Manitex M1768

LOAD CHARTS
for Use With
WRITTEN EXAMINATIONS
Manitex M1768
Manitex, Inc., by providing pages of one of its manuals, is not providing a substitute for training on a Manitex crane. These pages are reproduced for illustration only and not as a substitute for reviewing the entire manual for a particular crane. Make sure that you are fully trained on, and review the entire manual for, every crane you operate.
This load chart has been adapted from the original manufacturers load chart for use in the NCCER Mobile Crane Certification Examination. It is not to be used for calculating loads, planning lifts, or for any other purpose.
Millennium Series M1768 General Specifications
M o d e l s h o w n w it h o p t io n a l jib a n d
STANDARD EQUIPMENT
2-Speed planetary hoist. 5-Ton (4.5-mt) hook and ball. 2-Sheave boom point. Anti-two-block shutoff. Boom hoist cylinder. System pressure gauge. 70-Gallon (265-liter) hydraulic reservoir. Removable boom rest. .inish paint in Manitex colors. Engine start/stop. Operator/service/parts manuals. 3-Section telescopic boom 26 to 68 (7.93m to 20.73m). 260 .eet (79.25m) of 916" (14.3mm) EIPS IWRC wire rope. 372 Non-continuous rotation. Pedestal, turret, rotation bearing and swing system. Dual operator control stations. Hydraulic capacity alert warning system (HYCAS) - audio. Audible outrigger/stabilizer motion alarm. A-frame link type outriggers. A-frame rear stabilizer. 3-Section vane type hydraulic pump. Signal horn. 18-.oot (5.49m) Subframe.
Manitex M1768 Page 1 of 4
M1768 STANDARD SPECI.ICATIONS AND .EATURES

BOOM 26 To 68 (7.93m to 20.73m). Inverted-T cross section. 3-Section telescoping type, extended and retracted proportionally by double-acting hydraulic cylinder and cablecrowd system. Maximum tip height 79 (24.09m). BOOM POINT Two high-density nylon sheaves mounted on heavy-duty roller bearings. Two removable pin-type rope guards. HOIST Maximum theoretical line speed 247 fpm (75.29 mpm). Maximum theoretical bottom-layer line pull 12,000 lb (5,443 kg). Two-speed planetary reducer. Spring-applied, pressure-released internal brake. WIRE ROPE 260 (79.25m) of 9/16" (14.29mm) diameter 6 x 25 EIPS IWRC. BOOM ELEVATION Double-acting hydraulic cylinder. Working range from 13 below horizontal to 80 above. SWING SYSTEM Externally mounted, double-reduction planetary driven by hydraulic motor. Maximum theoretical swing speed 1.80 rpm. Wet multi-disc internal brake is spring applied, pressure released. Oversized diameter ball bearing swing circle with external gear. 372 Non-continuous rotation. OUTRIGGERS 2010 (6.13m) Extended. A-frame link type. Operated independently for precise leveling. Equipped with double-acting hydraulic cylinders. 16" x 20" (406mm x 508mm) Pivoting pads. 8 12" (215.9mm) Maximum rise. A-.RAME STABILIZERS 8 (2.44m) Retracted; 10 (3.05m) extended. Operated independently for precise leveling. Double-acting hydraulic cylinders. 8" x 11" (203mm x 279mm) fixed pads. 9" (229mm) Maximum rise. SUB.RAME Torsionally resistant, rigid 4-plate design. Mounted under crane full length of truck frame. REAR UNDERRIDE PROTECTION Supplied on factory mounted cranes. .abricated structure mounted under rear of bed. BACK-UP ALARM Supplied on factory-mounted cranes. Electronic audible motion alarm activated when truck transmission is in reverse gear. MOUNTING Pedestal and subframe are mounted to chassis by threaded rods and clamp plates. No welding, drilling, or bolting to truck. CONTROL SYSTEM Dual operator stations are equipped with four single-lever crane controls arranged to ANSI B30.5 standards. .ully proportional control valves and system pressure gauge. Each station also includes outrigger and stabilizer controls, engine start/stop, foot throttle, signaI horn, capacity light indication, boom-angle indicator, bubble levels, load chart and range diagram. HYDRAULIC SYSTEM A 3-section vane pump direct mounted to power take-off on truck transmission provides 35 gpm (133 lpm) to the hoist, 8 gpm (30 Ipm) to the swing circuit and 18 gpm (68 lpm) to other crane functions. 70-Gallon (265-liter) baffled reservoir includes 10-micron filter in the return line. Extensive use of SAE O-ring and face seal O-ring hydraulic fittings. HYDRAULIC CYLINDERS All are equipped with integral holding valves. BOOM REST Heavy-duty fabrication. Easily removed to simplify loading and unloading. LOAD HOOK 5-Ton (4.5-mt) capacity hook with heavyduty swivel and weight is provided for single-line operation. HYDRAULIC CAPACITY ALERT SYSTEM (HYCAS) Hydraulically senses boom hoist cylinder pressures and indicates an overload condition with an audible alarm. Optional shutdown prevents continuing overload. ANTI-TWO-BLOCK SYSTEM Audible warning and shutoff functions prevent hook from contacting boom point. ELECTRICAL 12-Volt direct current. Environmentally sealed enclosure contains accessory circuit, terminal strips and relays. In-line fuse. DESIGN/WELDING Design conforms to ANSI B30.5. Welding conforms to AWS D1.1. MANUALS Operator, service and parts manuals depict correct crane operation, maintenance procedures and parts listing. WARRANTY 12-Month warranty covers parts and labor resulting from defects in material or workmanship.
OPTIONS
pressures. Color-coded gauge at each operator station and audible alarm indicate approaching overload. Optional shutdown system hydraulically prevents continuing overload.
ELECTRONIC CAPACITY ALERT SYSTEM (ECAS) Electronically senses boom hoist cylinder
.IXED SWING-AROUND JIB 23 (7.01m)

.ixed length. stows along boom base. Maximum tip height 101 (30.79m).
TELESCOPIC SWING-AROUND JIB Working lengths 23 (7.01m) and 40 (12.19m). Stows along boom base. Telescopic section stows inside jib base. Manually pinned in retracted or extended position. Maximum tip height 118 (35.97m). H-STYLE STABILIZERS Two vertical double-acting hydraulic cylinders - 18" (457.2mm) stroke with 12" (304.8mm) diameter pivoting pads. to 6.10m). Deck of high density hardwood or diamond steel tread plate. Cross sills on 12" (305mm) centers. Bolts to subframe.
916
BED Choice of 8 x 14 to 20 lengths (2.44m x 4.27m

(14.3mm) rotation-resistant wire rope. Hook blocks for 2- to 4-part load line. Hanger sheave for 3- or 4-part line. Aerial baskets, 1- or 2-person. Top mounted work platform. Radio remote-control operation. .ront-bumper stabilizer for 360 operation. Hydraulic swivel for continuous rotation. Capacity overload shutdown system. Dunnage/tool boxes. Air throttle. Various mountings. Special paint. Roofing application. Hydraulic hose reel. Oil cooler for duty-cycle applications.
OPERATOR ASSIST .EATURES

Anti-Two-Block Warning and Shutoff Capacity-Alert System, Audio Warning Load Chart/Range Diagram Boom-Angle Indicator Audible Outrigger/Stabilizer Motion Alarm Engine Start/Stop Signal Horn Back-Up Alarm
Page 2
M1768 RANGE DIAGRAM

130 39.62 120 36.58 110 33.53 100 30.48 Height Above Ground in Feet Meters 90 27.43 80 24.38 70 21.34 60 18.29 50 15.24 40 12.19 30 9.14 20 6.10 10 3.05 Ground Level 0 20 10 40 60 70 30 50 80 90 3.05 6.10 9.14 12.19 15.24 18.29 21.34 24.38 27.43 Operating Radius from Centerline of Rotation in .eet Meters 80 75
AREA O. OPERATION
70
65 60 55 40-.oot Jib 50 12.19m Line through Centerline of Rotation 45 40
180 .ull Capacity Work
Optional 360 Operation
Centerline of Rotation
75
35 60 55 50 68 .eet 20.73m 45 40 58 .eet 17.68m 35 WARNING 48 .eet 30 Boom must be 14.63m fully retracted 25 when jib is 38 .eet 20 erected before 11.58m lowering boom 15 through 26 .eet this area. 10 7.93m 5 0
70
23-.oot Jib 7.01m 65
ALLOWABLE LINE PULL
WARNING
Anti-Two-Block system m u s t be in good op e rat ing cond ition before operating crane. Refer to Owners Manual. Keep at least three wraps on load line on drum at all times.
8500 lb 3856 kg 7400 lb 3357 kg
17000 lb 7711 kg 14800 lb 6313 kg
25500 lb 11567 kg 22200 lb 10070 kg
34000 lb 15422 kg 29600 lb 13426 kg
'$" (14.29mm) 6x25 IWRC

(3.5:1 SF). 29750 lb (13494 kg) Minimum breaking strength.
'$" (14.29mm) Rot resistant

(5.0:1 SF). 37000 lb (16783 kg) Minimim breaking strength.
WEIGHTS
Total crane, including hydraulic fluid.. .....................13,900 lb..... 6,305 kg 23 (7.01m) .ixed length jib...........................................545 lb........ 247 kg 40 (12.19m) Telescopic jib...........................................820 lb........ 372 kg 15-Ton (13.6-mt) single-sheave block ..........................260 lb........ 118 kg 20-Ton (18.1-mt) double-sheave block ........................350 lb....... 159 kg Hanger sheave for 3- and 4-part line ..............................50 lb.......... 23 kg 204" (6.20m) steel or wood bed ................................1,900 lb........ 862 kg
DEDUCTIONS
Auxiliary Block ............................................ 50 lb ......... 22.68 kg Overhaul Ball ..............................................120 lb ......... 54.43 kg Single-Sheave Load Block .........................260 lb ....... 117.93 kg Double-Sheave Load Block .......................350 lb ....... 158.76 kg Hose Reel...................................................190 lb ......... 86.18 kg
Outriggers and stabilizers fully extended and machine level.
Swing-Around Jib (Stowed) .......................See Load Rating Chart WARNING Lifting off the main boom point while the swing-around jib is erected is not intended or approved.
Meets ANSI B30.5 Requirements.
M1768 LOAD RATING CHART

BOOM LOAD RATINGS
11.58 Meters lb kg
9,752 8,373 7,262 6,042 4,695 3,769 2,998 2,068 78 14,600 76 12,680 72 10,500 65 58 51 42 32 16 8,160 6,570 5,420 4,470 3,580 2,380 6,623 5,752 4,763 3,701 2,980 2,459 2,028 1,624 1,079 79 11,810 76 70 65 59 53 47 39 29 15 9,830 7,690 6,240 5,200 4,390 3,720 3,120 2,500 1,610 5,357 4,459 3,488 2,830 2,359 1,991 1,687 1,415 1,134 730 78 74 70 65 60 55 50 43 36 28 14 9,200 7,280 5,910 4,940 4,200 3,610 3,110 2,670 2,240 1,780 1,400 4,173 3,302 2,681 2,241 1,905 1,637 1,411 1,211 1,016 807 635 78 75 72 69 65 62 58 55 50 46 41 36
Operating Radius Feet 5 8 10 12 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90
JIB LOAD RATINGS

20.73 Meters lb kg
7.92 Meters lb kg Meters

1.52 2.44 3.05 3.66 4.57 6.10 7.62 9.14 10.67 12.19 13.72 15.24 16.76 18.29 19.81 21.34 22.86 24.38 25.91 27.43 77 34,000 15,422
26 Feet
38 Feet
14.63 Meters lb kg
48 Feet
17.68 Meters lb kg
58 Feet
68 Feet
7.01 Meters lb kg Fixed Jib
23 Foot
12.19 Meters lb kg Telescopic
40 Foot
70 24,000 10,886 77 21,500 66 20,110 61 17,360 52 14,310 36 10,490 9,122 7,874 6,491 4,758 74 18,460 71 16,010 66 13,320 57 10,350 47 36 17 8,310 6,610 4,560
3,500 3,060 2,700 2,400 2,150 1,950 1,770 1,550 1,350 1,160 1,010 830
1,588 1,388 1,225 1,088 975 884 803 703 612 526 458 376 78 75 72 70 67 64 61 58 55 51 48 44 40 35 1,940 1,690 1,490 1,320 1,180 1,060 960 870 790 730 670 610 570 520 880 767 676 599 535 481 435 395 358 331 304 277 259 236
This capacity chart is for reference use only and must not be used for a specific serial number crane. Main boom load ratings are based on machine structural competence and do not exceed 85% of tipping.
Do not operate crane or accessories within 10 (3.05m) of live power lines.

480 218 330 150 260 118 220 100 190 86
Deductions for stowed jib
Page 3
M1768 OUTLINE DIMENSIONS

353" 10.74m 26 7.92m Retracted 68 20.73m Extended 19" 482.6mm
3.81m
126"
1.7m
57"
1333.5mm
52.5"
23" 584.2mm 21" 533.4mm

These dimensions are general, not for engineering. Some dimensions depend on truck selection.
12" 304.8mm 36" 914.4mm
168" 4,267.2mm 238" 6045.2mm
990.6mm
39"
TRUCK CHASSIS DATA

Minimum Requirements
Some configurations and options may increase requirements.
M1768 365" 11.10m Retracted 79 24.08m Extended 118 35.97m Jib Extended 80 13 7 1 1 "
2.4m
Wheelbase................................................ 238 In..........6,045mm Cab to Axle ............................................... 168 In..........4,267mm .rame Section Modulus ........................... 18 In3 ............ 3.295cc 50,000 psi..... 344,750 kPa .rame Section Modulus ......................... 15.9 In3 ............... 260cc 110,000 psi..... 758,450 kPa Nominal .rame Width ............................... 34 In.............864mm .ront Axle Gross Weight Rating .......... 12,000 lb........... 5,443 kg Rear Axle Gross Weight Rating........... 21,000 lb........... 9,525 kg
203.23mm 177.8mm
8"
3.05m
10
7"
2010"
6.35m
10" 254mm
Manitex Inc.
P.O. Box 1609
Form 842-597 Printed in USA
Georgetown, TX 78627-1609
Tel (512) 869-0552
Fax (512) 863-3776

1997 Manitex Inc
Due to continuing improvements, Manitex reserves the right to change product specifications without notice.
Page 4

Manitex M1768

Uploaded by

Copyright:

Available Formats

Manitex M1768

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manitex M1768

Uploaded by

Copyright:

Available Formats

LOAD CHARTS

for Use With

Millennium Series M1768 General Specifications

Manitex M1768 Page 1 of 4

M1768 STANDARD SPECI.ICATIONS AND .EATURES

.IXED SWING-AROUND JIB 23 (7.01m)

BED Choice of 8 x 14 to 20 lengths (2.44m x 4.27m

OPERATOR ASSIST .EATURES

Manitex M1768 Page 2 of 4

M1768 RANGE DIAGRAM

65 60 55 40-.oot Jib 50 12.19m Line through Centerline of Rotation 45 40

180 .ull Capacity Work

Optional 360 Operation

23-.oot Jib 7.01m 65

ALLOWABLE LINE PULL

8500 lb 3856 kg 7400 lb 3357 kg

17000 lb 7711 kg 14800 lb 6313 kg

25500 lb 11567 kg 22200 lb 10070 kg

34000 lb 15422 kg 29600 lb 13426 kg

'$" (14.29mm) 6x25 IWRC

'$" (14.29mm) Rot resistant

M1768 LOAD RATING CHART

Operating Radius Feet 5 8 10 12 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90

JIB LOAD RATINGS

7.92 Meters lb kg Meters

7.01 Meters lb kg Fixed Jib

12.19 Meters lb kg Telescopic

Do not operate crane or accessories within 10 (3.05m) of live power lines.

Deductions for stowed jib

Manitex M1768 Page 3 of 4

M1768 OUTLINE DIMENSIONS

23" 584.2mm 21" 533.4mm

12" 304.8mm 36" 914.4mm

168" 4,267.2mm 238" 6045.2mm

TRUCK CHASSIS DATA

Tel (512) 869-0552

Fax (512) 863-3776

Manitex M1768 Page 4 of 4

You might also like

'$" (14.29mm) 6x25 IWRC

'$" (14.29mm) Rot resistant