The Secret of Hydraulic Schematics

BTPHydraulics www.iranfluidpower.com

w w .ir w an flu id po w er .c om

Table of Contents
The Secret to Reading and Interpreting Hydraulic Schematics ................................................. 1 Hydraulic System Schematics ................................................................................................................ 1 Reservoirs ....................................................................................................................................................... 2 .............................................................................................................3 Hydraulic Lines, Tubes & Hoses ............................................................................................................. 3 Pumps .............................................................................................................................................................. 5 Hydraulic Motors ......................................................................................................................................... 7 Hydraulic Cylinders ..................................................................................................................................... 8 Area, Volume & Cycle Time ..................................................................................................................... 10 Pressure Control Symbols ....................................................................................................................... 11 Pressure Relief Valve ................................................................................................................................ 12 Sequence Valve ........................................................................................................................................... 13 Pressure Reducing Valve ......................................................................................................................... 14 Directional Control Valves ...................................................................................................................... 15 Two Position Flow Control Valves .......................................................................................................... 17 Three Position Flow Control Valves ..................................................................................................... 18 How Valves Are Actuated ...................................................................................................................... 19 Flow Control Mechanisms ...................................................................................................................... 20 Fluid Conditioning Mechanisms and Symbols .................................................................................. 21 Accumulators ............................................................................................................................................. 22 Miscellaneous Mechanisms and Symbols ........................................................................................ 23

Reading and Interpreting Hydraulic Schematic S ymbols

Sullivan

Page 1

The Secret to Reading and Interpreting Hydraulic System Schematics

The secret to being successful at reading and interpreting a schematic for a hydraulic system is really quite simple. Very often, technicians will forget that the symbols on schematics are really a completely different language of pictographs pictures of what the object does used to represent the component. As you read this manual and begin to study the symbols inside, go to the extra effort to try and figure out why the symbols are drawn as they are. If you think about it, pumps will look like what pumps do, and all of the other symbols will come close to looking like what they are intended to be. As 1. 2. 3. you read the schematic, remember the following: You already have a good idea of what the machine does and how the components work. The schematic is a picture of the machine, which does what you understand. Therefore, whether it looks like it or not, the schematic and the machine match match.

Dont forget what you already know when you pick up a schematic use what you know to force the schematic to make sense. Take the time to learn what the system is supposed to do. This is what a schematic is for to teach why a system does what it does. lost, If you get lost remember that you always have to have fluid flowing, and as it flows it follows this path: starting at the pump, fluid flows from high pressure to low, and ends up back at the reservoir. Good luck. Reading and Interpreting Hydraulic Schematic Symbols
Sullivan

Page 1

Reservoirs
Reservoirs are used to contain fluid, provide cooling, separate out air and sludge, and provide a head pressure to the pump if the reservoir is pressurized.

VENTED RESERVOIR

PRESSURIZED RESERVOIR

PRESSURIZED RESERVOIR PRESSURIZED RESERVOIR

Reservoirs can also be drawn to show the point of connection for suction and return lines.

VENTED RESERVOIR OIL RETURN ABOVE OIL LEVEL

VENTED RESERVOIR OIL RETURN BELOW OIL LEVEL

VENTED RESERVOIR SUCTION LINE ATTACHED TO BOTTOM

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 2

Hydraulic Lines, Tubes & Hoses

Hydraulic lines, tubes and hoses (or any other conductor) that carry the fluid between components is drawn as a line.

PRESSURE OR RETURN LINE

OIL FLOWS IN ONE DIRECTION

OIL FLOWS IN BOTH DIRECTIONS

PILOT LINES

DRAIN LINES

FLEXIBLE LINE

GASEOUS SUPPLY SHOWING DIRECTION

OUTLINE FOR ENCLOSURE

INSTRUMENT LINE

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 3

Hydraulic Lines, Tubes & Hoses (continued)

Connections for lines and hoses are shown below. Pay particular attention to the presence of a dot at the intersection of lines. If theres no dot visible and lines cross, the lines do not connect. If lines intersect but one line ends, then even without a dot the lines do connect.

LINES CONNECTED

LINES CONNECTED

LINES CONNECTED

LINES NOT CONNECTED

LINES NOT CONNECTED

LINES NOT CONNECTED

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 4

Pumps
Pumps are drawn as circles with triangles pointing outward from the center. The triangle represents the direction that fluid flows out of the pump and should be viewed as an arrow. A single arrow shows a one-direction (unidirectional) pump, while two arrows indicate a reversible (bidirectional) pump. A diagonal arrow cutting across the pump body indicates the pump displacement (output flow and volume) can be adjusted. A small rectangle on the side of the pump with a small arrow inside indicates that the pump output is compensated (adjusted or controlled) by a pressure signal from a pilot line.

INLET

OUTLET

FIXED DISPLACEMENT UNIDIRECTIONAL

FIXED DISPLACEMENT REVERSIBLE

VARIABLE DISPLACEMENT

VARIABLE DISPLACEMENT PRESSURE COMPENSATED

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 5

Pumps (continued)
Pumps are also drawn to indicate how their output can be controlled. Note that the attachments to the pumps look like the components they represent. The lever and pedal look like a lever and pedal. The drive shaft is shown as a pair of lines on the side of the pump, either with or without an arrow showing the direction of rotation. Pumps can also be drawn as stacks, which indicates that all pumps are driven by the same driveshaft or PTO.

LEVER CONTROLLED

PEDAL CONTROLLED

PUMP WITH DRIVE SHAFT

DRIVE SHAFT SHOWING DIRECTION

PUMP STACK

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 6

Hydraulic Motors
Hydraulic motors are actually hydraulic pumps that work in reverse. Except for a few minor differences pumps and motors are virtually identical. Use the same rules to interpret motor symbols as you would pump symbols.

OUTLET

INLET

NON-REVERSIBLE MOTOR

REVERSIBLE MOTOR

BI-DIRECTIONAL PRESSURE COMPENSATED

MOTOR WITH DRIVE SHAFT

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 7

Hydraulic Cylinders
Hydraulic cylinders convert fluid power to linear mechanical power. Fluid under pressure pushes against the ends of the piston to move it in order to move some other mechanism. Cylinders are drawn as rectangles with lines in the center to represent the piston and lines through the piston, ends to represent the rod Fluid ports are shown on the outer ends of the cylinder barrel rod. barrel. A single-acting cylinder only has one port so that fluid under pressure only enters one end and pushes only in one direction. The cylinder reverses by opening a valve to let gravity or a spring return the piston to the other end. A double-acting cylinder has ports at each end so pressurized fluid will enter both ends and push against the piston in both directions.

PORT

PISTON ROD

BARREL TYPICAL HYDRAULIC CYLINDER

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 8

Hydraulic Cylinders (continued)

SINGLE-ACTING CYLINDER

DOUBLE-ACTING CYLINDER

DOUBLE ROD-END CYLINDER

DIFFERENTIAL CYLINDER

SINGLE ROD END WITH A FIXED CUSHION AT BOTH ENDS

SINGLE ROD END WITH ADJUSTABLE CUSHION ON ROD END ONLY

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 9

Area, Volume & Cycle Time

The speed at which a cylinder moves is based upon the fluid flow rate (in gallons/minute or cubic feet/minute) and the volume (displacement) of the piston. Cycle time is the time it Cycle time takes a cylinder to move its full length, and is found by dividing the displacement of the cylinder (area x stroke) by the flow rate, then multiplying by 60 seconds Cycle time is critical in seconds. diagnosing a hydraulic problem.
AREA Area = 3.14 x radius
2

STROKE

VOLUME (CID) = Area x Stroke CYCLE TIME = (Volume/Flow Rate) x 60 150 cu. in. cylinder 450 cu. in. per minute flow x 60 sec = 0.333 x 60 = 20 sec
Volume and Displacement are the same, and are found by multiplying area times length. When calculating cycle time, make sure you use the same units of measurement. Cubic feet per minute cannot be used with gallons, and vice versa. Reading and Interpreting Hydraulic Schematic Symbols Page 10
Sullivan

Pressure Control Symbols

Hydraulic pressure is controlled through the use of valves that open and close at different times to allow fluid to be pressure. bypassed from points of high pressure to points of low pressure The basic valve symbol is a square which represents the valve body or spool An arrow in the center represents the path oil takes through the valve. spool. Pressure control valves are typically pilot operated that is, the valve is moved automatically by hydraulic pressure and not by a person. Pilot oil pressure is resisted by a spring, which can often be adjusted. The higher the spring tension, the valve. more fluid pressure is required to move the valve To visualize the operation of this type of valve, imagine that the entire square will move away from the pilot line and towards the spring. If the valve is normally-open fluid flow will be cut off by the pilot line. If the valve is normally-closed the normally-open, normally-closed, pilot line will cause oil to start flowing. Valves can either be on/off valves with no flow in the middle, or infinitely variable, which means flow will gradually increase or decrease as pilot pressure increases and/or decreases.
INLET PILOT LINE

SPRING

SPRING

INLET PILOT LINE

OUTLET

OUTLET

NORMALLY OPEN VALVE

NORMALLY CLOSED VALVE

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 11

Pressure Relief Valve

A pressure relief valve is a normally closed valve that senses the high pressure at its inlet. As the pressure at the inlet increases, the pressure in the pilot line begins to push against the valve body (spool). As the valve body moves, the ports begin to line up and fluid will begin flowing through the relief valve. The relief valve typically dumps back into the reservoir. Most relief valves are infinitely variable.

PRESSURE RELIEF VALVE

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 12

Sequence Valve
A sequence valve is a normally closed valve that opens once the inlet pressure reaches a preset point. This type of valve is designed to allow different components to act sequentially, meaning one after the other. Once the primary actuator reaches the limit of its travel fluid pressure in the feed line will rise. This rising pressure opens the sequence valve which allows fluid to flow through it to the secondary cylinder.

TO PRIMARY CYLINDER

SEQUENCE VALVE

TO SECONDARY CYLINDER

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 13

Pressure Reducing Valve

A pressure reducing valve is a normally open valve that senses the outlet pressure going to an actuator. As the pressure in the outlet increases, pilot pressure increases which gradually closes the reducing valve. As the valve closes, oil from the high pressure side of the valve is directed back to the reservoir which dumps pressure at the outlet.

OR
PRESSURE REDUCING VALVE PRESSURE REDUCING VALVE

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 14

Directional Control Valves

The direction that fluid flows in a line can be controlled by using valves which allow flow in only one direction. These valves are typically referred to as check valves because they check the flow if it tries to reverse. These valves can have simple check balls or can have machined poppet type valves. They can also be more complex pilot operated valves that have spools. ball. In the case of a ball check valve, the allowed flow is opposite the arrow, or towards the ball If the valve has no spring, the valve offers resistance to flow only in the closed direction; in the open direction the valve moves with any movement of fluid and does not have a pressure setting. If the check valve has a spring it will oppose flow in the open direction up to the point where hydraulic pressure overcomes spring tension. Check valves can also be pilot operated.

NO FLOW

FREE FLOW

ONE WAY VALVE (CHECK VALVE)

BY-PASS VALVE (SPRING LOADED CHECK VALVE)

PILOT OPERATED BY-PASS VALVE

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 15

Directional Control Valves (continued)

Another method of drawing check valves (directional valves) is using composite symbols as in the previous sequence. This method contains a blocked path and a free path. The dashed lines represent pilot pressure lines. As pressures increase on the blocked side of the valve, that pilot line moves the valve to reduce or cut off supply, depending upon whether the valve is normally open or closed. The spring keeps the valve in the normal position If pressure builds up on the flow side of the valve, the position. pilot line pressurizes and moves the valve into the open position, compressing the spring in the process, and allowing oil to flow. If the flow attempts to reverse, the other pilot line pressurizes and adds to spring pressure to close the valve, cutting off flow. These valves are commonly referred to as flow dividers or flow control valves. This type of valve can be a pressure relief valve or pressure reducing valve depending upon location of pilot source and spring setting.

FREE FLOW
NO FLOW ONE WAY VALVE SHOWN CLOSED

PILOT PRESSURE FROM RIGHT PUSHES VALVE UPWARD TO ALLOW FLOW

Sullivan

Reading and Interpreting Hydraulic Schematic Symbols

Page 16

Two Position Flow Control Valves

Two position flow control valves typically are used to make the flow reverse to an actuator in a simple system, although other arrangements are possible. The valve spool slides long-ways to allow one or the other valve position to direct flow. Because these valves have no center position they must be used with a pressure relief valve that opens to dump system pressure when the actuator bottoms out.

Note that the direction of oil flow does not change on the pump side of the valve The direcvalve. tion changes only after the valve flip-flops the flow to redirect pressure to the retracted side of the cylinder. Reading and Interpreting Hydraulic Schematic Symbols
Sullivan

Page 17

Three Position Flow Control Valves

Flow control valves are drawn as composite symbols using squares to represent the valve spool. To visualize the operation of these valves its necessary to imagine them moving longways with the spool sliding to move the different flow arrows into a position to allow oil to flow through them. The centers of the valves determine what type of system is in use. An open center system uses valves that allow oil to flow through them at all times out of the pump and back into the reservoir when no actuators are in use. This system does not require a pressure relief valve. A closed center system uses valves that block flow through them when no actuators are in use, thereby liquid locking the system. In this type of system a pressure relief valve is mandatory to prevent the system from destroying itself when the valves are in the center.

OPEN CENTER VALVE & SYSTEM

CLOSED CENTER VALVE & SYSTEM WITH PRESSURE RELIEF VALVE

Sullivan

Reading and Interpreting Hydraulic Schematic Symbols

Page 18

How Valves Are Actuated

There are a variety of ways to actuate control valves. These include manually by hand with a lever, manually by foot with a pedal, with an electric solenoid (coil), using external pilot pressure, using a spring, using internal pilot pressure, or using any combination of the above.

LEVER CONTROLLED

PEDAL CONTROLLED

SOLENOID CONTROLLED

INFINITELY VARIABLE
(NOT JUST ON AND OFF)

PILOT PRESSURE CONTROLLED

SOLENOID OPERATED WITH INTERNAL PILOT PRESSURE

SOLENOID OPERATED WITH INTERNAL PILOT PRESSURE AND SPRING CENTERING

Sullivan

Reading and Interpreting Hydraulic Schematic Symbols

Page 19

Flow Control Mechanisms

Sometimes its necessary to slow down flow or to create a pressure drop at some point in the system. This is done with a restrictor (snubber) that is similar to a fuel jet. Snubbers are drawn to represent a pinch in the line, and can either be fixed or variable, and can be controlled by other systems as well such as being temperature or pressure controlled.

FIXED RESTRICTOR

ADJUSTABLE RESTRICTOR

ADJUSTABLE RESTRICTOR PRESSURE COMPENSATED

ADJUSTABLE RESTRICTOR PRESSURE & TEMPERATURE COMPENSATED

Sullivan

Reading and Interpreting Hydraulic Schematic Symbols

Page 20

Fluid Conditioning Mechanisms and Symbols

Oil is conditioned by various mechanisms. Conditioned implies that the condition of the oil is changed from one state to another. Typical conditioners are filters, heaters and coolers. In addition, these mechanisms can contain drains of various sorts.

FILTER OR STRAINER

COOLER

HEATER

TEMPERATURE CONTROL UNIT

MANUAL DRAIN SEPARATOR

AUTO DRAIN SEPARATOR

MANUAL DRAIN FILTER SEPARATOR

AUTO DRAIN FILTER SEPARATOR

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 21

Accumulators
Hydraulic accumulators act as shock absorbers for the system. They are installed in parallel with the pump and do several things. They provide a small amount of emergency flow for steering and brakes, dampen out oscillations in pressure (keeping pressure constant), and provide flow when components move and activate. Theyre drawn as ovals with a line in the center which represents the diaphragm or piston that separates the oil from the nitrogen or spring.

PNEUMATIC (GAS FILLED) ACCUMULATOR

SPRING LOADED ACCUMULATOR

Reading and Interpreting Hydraulic Schematic Symbols

Sullivan

Page 22

Miscellaneous Mechanisms and Symbols

QUICK DISCONNECTS (CONNECTED)

QUICK DISCONNECTS (DISCONNECTED)

SPRING

PRESSURE SWITCH

RATCHETING DETENT ON VALVE

MANUAL SHUTOFF VALVE

TEST POINT FOR GAUGE

TEMPERATURE INDICATOR
Sullivan

PRESSURE INDICATOR

Reading and Interpreting Hydraulic Schematic Symbols

Page 23