TX50S manual

TECHNICAL , MAINTENANCE AND INSTALLATION MANUAL

TX50S FM TRANSMITTER

JUNE 2000
CTE international Via Sevardi 7 42010 Mancasale (REGGIO E.) ITALY

Pag. 1

TX50S manual

OWNERS MANUAL MAINTENANCE MANUAL TX50S FM TRANSMITTER

Printed : 06-05-2000 Rev. A Cod. MAN-TX50-06052000A

IN ACCORDING TO R&TTE RULES NOTIFIED BODY : 0523

ITALY RESTRICTIONS : Luso dellapparato soggetto a concessione Potenza RF 50 Watt Canalizzazione 100 Khz (solo mod. TX50S)

All rights are strictly reserved Reproduction or issue to third parties in any form whatever is not permitted without written authorization

Pag. 2

TX50S manual

CONTENTS

CHAPTER 1
1.1

SAFETY INSTRUCTIONS

Introduction--------------------------------------------------------------------------------- 6

CHAPTER 2
2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11

ELECTRICAL SPECIFICATIONS

Frequency and power----------------------------------------------------------------------- 8 Modulation capability ---------------------------------------------------------------------- 8 Characteristics in MONO------------------------------------------------------------------- 8 Characteristics in STEREO ----------------------------------------------------------------- 9 SCA characteristics------------------------------------------------------------------------- 9 Readout on LCD display ------------------------------------------------------------------- 9 Remote control ----------------------------------------------------------------------------- 9 Power supply and temperature range ------------------------------------------------------10 Mechanical specifications -----------------------------------------------------------------10 Options ------------------------------------------------------------------------------------10 Standards satisfied -------------------------------------------------------------------------10

CHAPTER 3
3.1 3.2 3.3

DESCRIPTION OF THE DEVICE

Main features ------------------------------------------------------------------------------11 Available options --------------------------------------------------------------------------12 Block diagram -----------------------------------------------------------------------------12

CHAPTER 4
4.2 4.2 4.3 4.4 4.5 4.6

INSTALLATION

Unpacking and inspection -----------------------------------------------------------------16 Installation---------------------------------------------------------------------------------16 Power supply ------------------------------------------------------------------------------16 Ground loops ------------------------------------------------------------------------------17 Transmitter power up ----------------------------------------------------------------------17 Transmitter settings------------------------------------------------------------------------17

Pag. 3

TX50S manual

Connection diagram -----------------------------------------------------------------------------------------------29

CHAPTER 5
5.1 5.2 5.3 5.4 5.5 5.6 5.7

CIRCUITS DESCRIPTION

AUDIO-IN board --------------------------------------------------------------------------30 SINTD board ------------------------------------------------------------------------------31 MBA board --------------------------------------------------------------------------------31 AGC board---------------------------------------------------------------------------------32 HSW board --------------------------------------------------------------------------------33 40WN and RFDC boards ------------------------------------------------------------------33 DLCD board -------------------------------------------------------------------------------34

CHAPTER 6
6.1 6.2 6.3 6.4

ADJUSTAMENTS

HSW module power supply -------------------------------------------------------------35 40WN module RF power module --------------------------------------------------------36 RFDC module directionl coupler --------------------------------------------------------36 MBA module mother board -------------------------------------------------------------37

CHAPTER 7
7.1 7.2 7.3 7.4

MODULATION MEASUREMENTS

General informations ----------------------------------------------------------------------40 Modulation peak analysis measurements--------------------------------------------------41 Modulation power measurements ---------------------------------------------------------45 Considerations on the real measurements performed -------------------------------------46

CHAPTER 8
8.1 8.2

REMOTE CONTROL

PC connection -----------------------------------------------------------------------------49 COM1--------------------------------------------------------------------------------------49

Pag. 4

TX50S manual

CHAPTER 9
9.1 9.2

INTERNAL AND REAR WIEW

Internal adjastments and settings -----------------------------------------------------------------55 Rear connections------------------------------------------------------------------------------------59

CHAPTER 10
10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 10.10 10.11

DIAGRAMS AND LAYOUTS

HSW board power supply ----------------------------------------------------------------63 AUDIO-IN board - audio inputs-----------------------------------------------------------67 DLCD boarddisplay driver ---------------------------------------------------------------73 MBA board mother board ---------------------------------------------------------------78 KEY board key --------------------------------------------------------------------------85 SINTD boardVCO oscillator -------------------------------------------------------------88 DMPX board stereocoder ----------------------------------------------------------------94 AGC board audio automatic gain control ------------------------------------------------97 CON boardMBA / RFDC connection-------------------------------------------------- 101 40WN board RF power module -------------------------------------------------------- 104 RFDC board directional coupler ------------------------------------------------------- 107

Pag. 5

TX50S manual

SAFETY INSTRUCTIONS
1.1 Introduction
CTE has always managed to improve the safety standard if its transmitting and receiving equipment. All produced systems are tested in compliance with international EN60950 and EN60215 rules. Obviously this is not sufficient to avoid any accident during the installation and the use of our equipment in compliance with EN60215 rule, the radio transmitters and the auxiliary equipment must be used by qualified technical staff only and CTE declines any responsibility for damages caused by an improper use or improper setting up performed by inexperienced staff, not qualified or operating with instruments or tools not in compliance with safety set of rules.

WARNING
CURRENT AND VOLTAGE WORKING IN THIS EQUIPMENT ARE DANGEROUS. THE STAFF MUST ALWAYS OBSERVE THE SAFETY RULES, INSTRUCTIONS AND NORMS CONTAINED HEREIN.

WARNING
THE INSTRUCTIONS CONTAINED IN THIS MANUAL MUST BE READ BEFORE SWITCHING ON OR SETTING THE TRANSMITTER

WARNING
ANY TRANSMITTER SERVICING, REPAIRING OR CHECKING OPERATION REQUIRING THE OPENING OF THE TOP OR BOTTOM COVER, MUST BE PERFORMED AFTER THE MAINS SUPPLY DISCONNECTION WITHOUT REMOVING THE EARTH CONNECTION WHICH THE EFFICIENCY MUST BE VERIFIED: THE CABLE MUST BE IN GOOD CONDITIONS AND WELL CONNECTED.

WARNING
STAFF OPERATING UPON THE TRANSMITTER SYSTEM MUST NOT BE TIRED: AFTER HEAVY WORKS OR CARRYING HEAVY MACHINES BY HAND, IT IS NECESSARY TO RESPECT A PERIOD OF REST BEFORE WORKING WITH SYSTEMS WHICH COULD HAVE DANGEROUS ELECTRIC VOLTAGE IF THEY ARE NOT DISCONNECTED.

Pag. 6

TX50S manual

WARNING
SEVERAL SYMBOLS, INSIDE THE TYPICAL TRIANGLE SHOWING DANGER, HAVE BEEN PRINTED ON SEVERAL TRANSMITTER PARTS. ATTENTION SHOULD BE PAID, BECAUSE THERE COULD BE THE DANGER DUE TO HOT SURFACES, ELECTRIC VOLTAGE HIGHER THAN 50VOLT OR OTHER SPECIFIED DANGERS. Certain devices (for example the RF final circuits mosfets) contain Beryllium Oxide BeO; these components must not be broken, crashed or heated. This oxide passes through the common systems of filtering, including the respiratory apparatus. The prolonged inhalation at high degrees causes poisoning with respiratory apparatus paralysis, till death.

WARNING
ALL THE MODULES CONTAINING BeO ARE MARKED WITH THE TRIANGULAR WARNING SYMBOL INDICATING THE NOTICE:

WARNING !

TOXIC HAZARD THESE DEVICES CONTAIN BERYLLIUM OXIDE OBSERVE SAFETY INSTRUCTIONS !

The staff in charge, besides being technically qualified, must have a practice of the first aid in case of emergency or accident (reanimation, heart massage, mouth to mouth respiration, etc.). Before going on with the operations to be performed, it is necessary to know the position of the general electric switch and the one of the extinguishers, which are to be used very quickly if necessary.

Pag. 7

TX50S manual

TX50S FM BROADCASTING TRANSMITTER

ELECTRICAL
2.1

SPECIFICATION

FREQUENCY - POWER

Frequency range---------------------------------------------------------------------------- 87.6 to 107.9MHz Frequency setting -------------------------------- in 100KHz steps (model TX50S-S have 10 Khz steps) Internal setting mode -----------------------------------------------------------------------------------by keys External setting mode ------------------------------------------------- by remote control ( RS232-RS485 ) Frequency stability------------------------------------------------------------------------------ 1000Hz/year Frequency generation------------------------------------------------------------------------ PLL synthesizer Modulation type ----------------------------------------------------------direct VCO frequency modulation Nominal frequency deviation -------------------------------------------------------------------------75KHz Deviation linearity in all frequency range------------------------------------------------------------ 0.2dB Peak detector error -------------------------------------------------------------------------------------- <0.1dB RF output power --------------------------------------------------------------------------------------0 to 50W Power resolution setting---------------------------------------------------------------------------------- 0.1W Power control limit setting --------------------------------------------------------------------------1 to 50W Power control stability -------------------------------------------------------------------------------- < 0.1dB Reverse output power control limit ---------------------------------------------------------------- 1 to 9.9W Reverse output power steps control--------------------------------------------------------------------- 0.1W Harmonics emission ---------------------------------------------------------------------------------- <-70dBc Spurious emission------------------------------------------------------------------------------------- <-95dBc Carrier reduction power ( carrier enable off )------------------------------------------------------- >60dBc

2.2

MODULATION CAPABILITY

MONO (left and right) ----------------------------------------------------------------------- 30Hz to 15KHz STEREO (by internal stereo generator) ---------------------------------------------------- 30Hz to 53KHz SCA (two channels) -------------------------------------------------------------------------30Hz to 100KHz COMPOSITE------------------------------------------------------------------- MONO or STEREO + SCA

2.3

CHARACTERISTICS IN MONO

Signal input ---------------------------------------------------------------------------------------- Left + Right Input impedance------------------------------------------------------------------- 600 (balanced) or 10k Unbalance rejection-------------------------------------------------------------------------------------->40dB Input level----------------------------------------------------------------------------------------6 to +12dBm Pre-emphasis ---------------------------------------------------------------------------------------- 75 or 50s Audio frequency response (30Hz to 15KHz) -------------------------------------------------------<0.15dB Audio frequency response ( 19KHz to 100KHz) ----------------------------------------------------<-40dB Modulation distortion---------------------------------------------------------------------------------- <0.03% Signal to noise ratio -------------------------------------------------------------------------------------->85dB

Pag. 8

TX50S manual

2.4

CHARACTERISTICS IN STEREO

Signal inputs -------------------------------------------------------------------------------------- Left or Right Input impedance------------------------------------------------------------------- 600 (balanced) or 10k Unbalance rejection-------------------------------------------------------------------------------------->40dB Input level----------------------------------------------------------------------------------------6 to +12dBm Pre-emphasis ---------------------------------------------------------------------------------------- 75 or 50s Audio frequency response (30Hz to 15KHz) -------------------------------------------------------<0.15dB Audio frequency response (19KHz to 100KHz)------------------------------------------------------<40dB cross-talk between left and right channel-------------------------------------------------------------->50dB Distortion at frequency deviation of 75KHz-------------------------------------------------------- <0.03% Distortion at frequency deviation of 100KHz ------------------------------------------------------ <0.03% Signal to noise referred at deviation of 75KHz------------------------------------------------------->80dB Suppression of 38KHz ---------------------------------------------------------------------------------->80dB Spurious suppression outside band------------------------------------------ .in according to ETS 300-384 Pilot reference for RDS encoder (19 Khz out)--------------------------------------------------------- 1Vpp

2.5

SCA CHARACTERISTICS

Input (SCA1, SCA2) ----------------------------------------------------------------------- BNC unbalanced Input impedance------------------------------------------------------------------------------------------ 10K Frequency response (50KHz to 100KHz) ------------------------------------------------------------ <0.1dB Distortion -------------------------------------------------------------------------------------------------<0.1% Modulation capability -------------------------------------------------------------------------------- 0 to 10%

2.6

READOUT ON LCD DISPLAY (40x4 character )

Forward power resolution -------------------------------------------------------------------------------- 0.1W Reverse power resolution -------------------------------------------------------------------------------- 0.1W Modulation resolution ------------------------------------------------------------------------------------1KHz Line voltage resolution -------------------------------------------------------------------------------------- 1V Power amplifier voltage resolution ------------------------------------------------------------------------ 1V Power amplifier current resolution-----------------------------------------------------------------------0.1A Heatsink temperature resolution--------------------------------------------------------------------------- 1C

2.7

REMOTE CONTROL

COM1 (front panel)--------------------------------------------------------------------------------------RS232 COM2 (rear panel) ---------------------------------------------------------------------------------------RS232 COM3 (rear panel) ---------------------------------------------------------------------------------------RS485 Personal computer software -----------------------------------------National Instruments LAB-VIEW Transmission protocol---------------------------------------------------------------------AES-EBU SP 490

Pag. 9

TX50S manual 2.8

POWER SUPPLY AND TEMPERATURE RANGE

Operating voltage --------------------------------------------------------------------- 115 or 230V AC 10 % Line power--------------------------------------------------------------------------------------------- <150VA Nominal temperature range ----------------------------------------------------------------------- -5 to 45C Operating temperature range ---------------------------------------------------------------------10 to 50C Storage temperature range ---------------------------------------------------------------------- -40 to 50C

2.9

MECHANICAL SPECIFICATION

19 rackmount--------------------------------------------------------------------------------- 485x88x500mm Weight------------------------------------------------------------------------------------------------------ 12Kg

2.10

OPTIONS

Option A -------------------------------------------------------------------------------------- Stereo generator Option B ---------------------------------------------------------------------Automatic Audio Level Control Option C --------------------------------------------------------------------------------------- Remote Control TX50S-S --------------------------------------------------------------------------------10 Khz frequency steps

2.11

STANDARDS COMPLYS ( R&TTE )

Electrical characteristics ----------------------------------------------------------------------- ETSI 300-384 EMC characteristics ---------------------------------------------------------------------------- ETSI 300-447 Safety characteristics ------------------------------------------------------------------ EN-60950EN-60215 Notified Body ------------------------------------------------------------------------------------------------0523

Pag. 10

TX50S manual

GENERAL DESCRIPTION
3.1 Main features
TX50S is a FM band broadcasting transmitter with modern conceiving and technology, which by a simple design produces an output radio signal with high characteristics of quality, reliability and security. The simple manufacturing obtained with a hi integration of functions, has allowed to create a machine with few controls and connections. Most printed circuits are multilayer with a surface mounting technology component assembling. The eventual repairing can be done by simply changing the fault involved board, without searching the defective component. One of the most important characteristics is done by the high quality of the frequency modulation and the high signal-to-noise ratio; moreover, the modulation is typically constant within 0.1dB throughout the whole FM band (88108MHz ). A proper peak detector allows to perform both traditional modulation measurements (usual bar-graph with peak), and modulation and power modulation ones with long observation periods (even with many hours or days) according to the latest international regulations, which properly cared to fix a limit scientifically measurable to the peak and modulation power (CEPT 54-01). An particular audio circuit can control the input audio level with a 6dB dynamics referred to the nominal value: this can be extremely useful when the audio signal level is not fixed or when this one can be subject to fluctuations (usually very slow) due to thermal driftsbad systems maintenance, possible damages along radio link paths etc. A proper board can be inserted to obtain this function and a proper microprocessor follows constantly the modulation value correcting through proper algorithms, implemented in its memory, the value of the modulator gain, keeping this way the modulation very close to the maximum allowed value. The corrections take place at very long periods of time; the board does not perform the audio compressing-limiting functions, but just compensates possible drifts occurring on the systems carrying the audio channel before entering in the FM transmitter. No measurable phase or amplitude distortion is introduced in the modulation when the automatic gain control circuit is enabled. In addition an alarm which switches the power off in case of modulation absence can be inserted since the unmodulated carrier transmission is forbidden in many countries, with no chance to identify the radio. The transmitter can be set like a modern signals generator so the output power is completely managed by a device which guarantees that the values of forward power, reflected power, maximum output power versus the temperature and loading conditions, are always the ones set or the ones allowed by maximum limits. A directional wide band coupler with remarkable directivity and large on board memory allows to obtain a power accuracy worthy of a good measurement instrument. All parameters (frequency, levels, mono/stereo, pre-emphasis, power) can be set by the keyboard and stored in E2 PROM in order to be kept even without electric supply. A great number of events can be stored: each alarm is distinguished by a starting and an ending alarm date. The

Pag. 11

TX50S manual controlled parameters are: modulation absence, heatsink temperature, mains supply voltage, RF power final stage voltage and current, main oscillator fault. Besides the keyboard, the transmitter can be remotely controlled in different ways. A personal computer can be connected as monitor to the DB9 socket placed on the front panel and by a special program, to be load easily on the PC, all the transmitter parameters can be set and seen. Furthermore its possible to perform all the modulation analysis provided by the CEPT 54-01 regulations and create the related graphics which can be stored as a file in the PC. A second RS232 port placed in the transmitter rear part can be connected to the power amplifier connected in series to the exciter, thus allowing the power data display on the same PC connected to the front RS232. A third RS485 port placed in the rear part can be connected to a MODEM which is connected to the phone line thus assuring the transmitter telecontrol, remotely or from the studio. The same RS485 port can be used for the connection N+1 of more transmitters (max 32). In this case a transmitter acts as a joker, so it replaces the faulty equipment, automatically adapting to all its parameters. Each transmitter is also provided with an output port (IN/OUT) suitable to drive the antenna cable multiplexer and the one for the input audio signals switching.

3.2

Available options
a) b) c1) c2) STEREO ENCODER AGC REMOTE CONTROL N+1 system : additional board allowing the internal encoding of the stereophonic signal : additional board allowing a frequency modulation control : software for the PC connection : software to obtain N+1 system

Model TX50S-S have 10 Khz frequency steps

3.3

Block diagram
The transmitter can be modulated by five different audio signal.

The first two ones are made by monophonic left and right channels, which can be balanced or unbalanced. The input dynamic goes from 6 to +12dBm with an input impedance w hich can be high or low. On these channels either the European or American pre-emphasis value can be inserted. A low pass filter on each of the two inputs assures a good attenuation of audio frequencies higher than 15KHz which could interfere, in case of stereophonic transmission, with higher band and with la subcarrier of the Multiplex signal; the out-of-band attenuation of the filter is not excessive in order not to increase then phase distortion (group delay) of the in band audio signal: 6070dB of attenuation, even with 0.1dB of amplitude linearity up to 15KHz, unavoidably creates a distortion on the analogue signal that an experienced ear can perceive. Right or left signals can be combined to generate monophonic transmission (should you only have one of the two signals, it Pag. 12

TX50S manual will be necessary to externally put in parallel the two inputs); in case of stereophonic transmission, the two channels are fed inside the stereo code board. The mono signal or the stereo one, thus obtained, is combined with the other three possible input audio signals: an external Multiplex signal and two SCA signals, one of which can be the RDS one, which can be synchronized with a 19KHz one connected on the IN/OUT rear connector. The composite signal can enter the AGC board, which has the task to check the its amplitude and consequently to keep the modulation at the correct value, or it can follow its path and enter into the frequency modulator after having passed through a limiter circuit (CLIPPER). This circuit must became active just in cases of faults of previous circuits or in case of mistake in the setting of the low frequency input nominal levels; this is to avoid to interfere with the adjacent channels. For not activating this fuse, which produces remarkable distortions on the modulation, it is necessary to take all proper cautions, that is the use of external compressor-limiters or by inserting the internal AGC circuit which protects a lot against damages and drifts. The oscillator, directly modulated by the composite signal, covers the whole FM band and its synthesized in steps of 10KHz . The reference frequency is obtained by a 10MHz crystal kept at constant temperature of 55C, whilst the output frequency is set by the main microcontroller. The oscillator phase noise is very good and it is in compliance with ETSI 300-384 regulations (<145dBc for a shifting of 1MHz from the carrier). The modulation linearity is typically contained within 0.1dB without complicated corrections. The RF final power circuit is wide band and it provides 50W RF output controlled with high accuracy; directional coupler has a directivity higher than 25dB on the whole band and an error which is lower than 0.2dB, it is also compensated in temperature and totally shielded. The power supply is of a switching type and it gives the four essential voltages, all obtained with this technique. A small voltage measurement transformer allows to check the effective value of mains supply voltage with accuracy and to interrupt the output power in case this value exits from the normal operating window of the transmitter (15% respect the nominal value of 115VAC or of 230VAC). The mechanical position of the power supply and the final circuits of RF power allow to obtain a vent flu just for cooling of the involved circuits, obtaining this way a really remarkable efficiency of that function. In normal running conditions, when the transmitter is working in a full power at environmental temperature, the radiator temperature is lower than 35C, whereas the other circuits temperature does not exceed 30C. No components are involved with the air flow, so it isnt requested a filter on the aspiration fan, which replacing is rather simple. The power supply is completely shielded both for internal circuits and for its unavoidable emissions toward the outside. Data displaying and setting is obtained by a board which is placed directly on the front panel containing a microprocessor, memory, keyboard, LCD display. The displaying area is wide so allowing to display and set needed data in a very easy way, thus making the transmitter-user technician interaction extremely user friendly. Its possible to protect the transmitter input and output parameter settings with a password, while all measurements can be done by whoever without interfering on its operation. Two communication RS232 ports and a RS485 port can make possible the communication between the transmitter and a PC, with the power amplifier and the driver exciter, or with a modem connected with the telephone line. Pag. 13

TX50S manual Maintenance or repairing of damages do not require the soldering use for the replacement of the parts to be changed; only six flat cables link all different boards.

Pag. 14

TX50S manual

TX50S BLOCK DIAGRAM

Pag. 15

TX50S manual

INSTALLATION
4.1 Unpacking and inspection
Immediately, after the transmitter has been delivered, please carefully check the package to verify possible damages caused by shipment. Should be found some damages, please immediately contact the CTE dealer. It is recommended to keep the original package for a future shipment d to, for instance, repairing ue or setting. A return with a package which is different from the original one will make the warranty rights lost.

4.2

Installation

The transmitter TX50S is composed of a 19 inches width rack which takes 2 units in height in a vertical rack mount. It is recommended to use 4 fixing plastic washers in order to avoid damages to the front panel varnishing. We remind to carefully connect the earth both to the transmitter and to the rack mountnever disconnect it without having switched the supply voltage off by the mains switch. Design has considered the new rules concerning the electromagnetic compatibility so there arent problems to locate systems CE marked nearby.

4.3

Power supply

AC power supply at 50/60Hz can be at 115VAC or 230VAC . The switching on control is placed for security reasons on the rear panel with the protection fuse, which must have the value 1.6A for the higher voltage and 3.15A for the lower one and it must be a delayed type. To change the value of the mains supply voltage, the small PCB placed inside the mains supply socket must be switched, taking care to place it in the position allowing to read of the needed voltage.

BEFORE SWITCHING THE TRANSMITTER ON, MAKE SURE THAT THE POWER SUPPLY IS CORRECT AND CONNECT THE RIGHT LOAD OR ANTENNA!

Pag. 16

TX50S manual

4.4

Ground loops

Sometimes connecting various ground sockets having different potentials may produce some unwanted loops, which may create hum in the modulation: in this case it is essential to firstly identify the origin of these currents, which normally spring from the antenna ground, mains supply ground or from the input low frequency signals ground. If the inconvenience can not be removed, the balanced input of the two channels LEFT and RIGHT can be used, thus obtaining common mode noise rejection of 40dB approximately. All the inputs and outputs are protected by diodes against the electrostatic discharges and they are provided with filters against the RF noise.

4.5

Transmitter power up

After making sure about the proper earth socket connection, correct power supply and connection of the load on the antenna output, the equipment can be switched on. If there is the first switching on, problems of wrong setting cant occur since the transmitter contains some standard values and the output power will be set to 0.5W, in order to avoid any problem of interference or driving for possible following amplifiers. The set values will be displayed and changed according to your need before the RF power is emitted from the transmitter. The equipment is provided with a memory which holds all settings even when the electric supply is off, however it is recommended to set the power at 0.5 W when uninstalling the transmitter itself to avoid any problem in case of a new setting up.

REMEMBER THE PASSWORD !

To enter the setting menu, knowing the password is mandatory. Its a four digits number written on the transmitter delivery document. Should it be forgotten, it will be possible to perform the set up by setting the Z2 jumper placed on the board DLCD (vertical board placed behind the rear panel) on the soldering side; the jumper is easy to identify through the close capture: PASSWORD ON/OFF. In this case, this operation must be performed with the equipment switched off and it requires also the opening of the top cover which, at ended operation, must be closed again with all its screws; it is essential to use a proper cross point screwdriver.

4.6

Transmitter settings

4.6.1 At the switching on, the display will glow giving for few seconds the following screen shot

Pag. 17

TX50S manual

4.6.2 Afterwards another page will appear for few seconds allowing to change the mains supply voltage value; the value setting operation to 115 or 230VAC by switching the network socket, and eventually changing the fuse value, allows the transmitter to operate correctly, but it doesn't allow the microprocessor controlling the equipment to know the mains supply voltage value. For this reason, if the value appearing on the said screen shot doesn't match with the one set on the rear voltage changer, it will be necessary to type ENTER to update to the changing; if the set value unmatched with the one read on the mains supply switch, the transmitter will turn to MAINS SUPPLY VOLTAGE ALARM, for example reading a 220VAC voltage when it is set for a 115VAC value: in this case the alarm is obviously given since the read voltage exceeds 15% of the nominal value (220V is almost the double of 115V).

If the line voltage appearing on the display matches with the one reading on the mains supply switch, it isnt necessary to type anything. On the opposite ENTER is required. On the screenshot the options contained in the transmitter and the hour of the last switching on will also appear and it will correspond to the current hour and date. If one finds out a discrepancy between the hour given and the current one, it will be necessary to correct the error in the clock setting. If this screenshot is accessed from another menu, the indication LAST POWER ON will show the last switching on date and it will be able to give the operator some indications about accidental switching off. 4.6.3 If all the indications are right, after a while the first page will be shown; which with the second one will contain all the most important measurements of the transmitter: Pag. 18

TX50S manual

The display is explanatory enough FREQUENCY is the output frequency set in MHz FORW. PW is the forward output RF power REFL. PW is the input reflected power on the RF connector LOCK ON shows that main oscillator is locked the programmed frequency MODULATION shows the modulation value of the COMPOSITE signal TEMPERATURE shows the radiator temperature value of the RF power final mosfet LINE VOLTAGE shows the mains supply voltage Moreover, in the lower part of the display, at the middle there is the indication of the number of alarms eventually set in the memory which have taken place after the last clearing of the memory. These ones will be displayed automatically by a continuous enter of PAGE UP. If one enters PAGE DOWN in this screen shot, the previous one returns and it will be possible to see once again the date of the last switching on or to change the mains supply voltage value. If an alarm is on, always in the same position of the display, the intermitting message ALARM will be pointed out. 4.6.4 important measures: By entering PAGE UP, its possible to see the second screen shot of the most

AUDIO LEVEL

PREEMPH. 75 AUDIO

is the nominal audio signal set on the setting window placed on the rear panel: if this value doesn't match to the needed one, its possible to choose 0 , 4.1 , 6dBm or, by placing the jumper on var, its possible to choose a value between 6 and +12dBm. is the chosen pre emphasis value, always on the rear window, also the value 50s can be selected; the inclusion or the disabling may be performed by the keyboard in a following screen shot. shows whether the transmitter is set to mono or stereo. Pag. 19

TX50S manual CARRIER EN PA VOLTAGE PA CURRENT MAX PW SET RFL PW SET shows if the output power is enabled either by a keyboard command or by an external command through the IN/OUT rear connector. is the supply voltage of the RF power final mosfet. is the voltage drained by the mosfet final power. is the maximum power value which can be programmed by the keyboard in the screen shot Forward PW adj (150W) to avoid accidental over drivings of the following amplifiers. is the maximum allowed output reflected power. Should this limit be reached, the direct power will be reduced to keep constant the limit value of the reflected power

4.6.5 displayed:

By entering again PAGE UP, eventual alarms present in the memory will be

They are stored in a chronological order ordered by number, type and date. Besides the real alarm, also the complementary event is stored (return to normality), in order to know the alarm period time:

By entering PAGE UP, the next alarm is displayed, or, if in the last screen shot of main measures there was not any alarm, it will be displayed the screen shot for the PASSWORD request to access the measures. If inside the transmitter the Z2 jumper placed on the DLCD board (in the rear of the front display panel board) is placed to OFF, this request is skipped, so its possible to directly set the transmitter. 4.6.6 The screen shot for the password request is the following:

Pag. 20

TX50S manual

To go on, it is essential entering the four numbers which can be known by reading the transmitter delivery document. If the password is unknown or it is too difficult to open the top cover by unscrewing the 20 locking screws, it is just possible to surf among the previous screen shots which give all the information about the transmitter. 4.6.7 By entering the right combination and then ENTER, the first setting of the transmitter is accessed:

In this screen shot i the maximum value of the direct power setting can be changed by the keyboard with the limit of 50W, this to avoid to drive an eventual following amplifier, which could bear an input maximum power of few Watts, with an excessive power and harmful consequences; therefore in this screen shot output power cant be adjusted, but a remedy is taken to solve a quite common error in the output power adjustment of the exciter-amplifier systems. The change and entry of new data may be performed by pressing the horizontal and vertical cursors and the ENTER button. 4.6.8 Entering instead PAGE UP, the following screen shot is accessed:

Pag. 21

TX50S manual In this screen shot, like in the previous one, its possible to set the higher limit of the allowed maximum reflected power. If the set limit tends to be exceeded, for a bad antenna operation or a bad load connected to the RF connector, the direct power is reduced proportionally so that this limit won't be exceeded, thus protecting the RF power final mosfet. Usually the reflected power limit is set to a value equal to 10% of the set direct power. Therefore, if the output power is adjusted at 50W, the reflected one can be 5W. The higher limit of this parameter is 10W and the resolution is 0.1W. 4.6.9 By entering PAGE UP, the following screen shot is accessed:

In this screen shot the output power can be set by means of NEW F. PW adj.. The resolution is 0.1W and the new direct power data are entered by the horizontal and vertical cursors and ENTER. After the new power has been set, it will be possible to read the power measurement really present on the antenna connector (forward and reflected), which may be slightly different from the set one due to the control circuit error or it may be very different in case of standing waves on the output circuit which forces the power control circuits to reduce the power in order not to exceed the reflected power limits. By means of the horizontal cursor, the power enable can be set, this software command doesn't operate if the transmitter is externally disabled through a CARRIER EN control placed on the rear IN / OUT connector. Each output power variation command is softly performed with the achievement of the final value in 3 seconds approximately. 4.6.10 By entering PAGE UP the following screen shot is accessed :

In this screen shot the output frequency can be set by the usual cursors with a resolution of 10KHz. On the display the current frequency and the new value appear. Pag. 22

TX50S manual After the ENTER key has been pressed for the new value, the output power is disabled for a few seconds, allowing the oscillator to exactly reach the new value. 4.6.11 By entering PAGE UP, the following screen shot is accessed:

All the rules concerning the radio transmitters in FM band include some limits of accuracy and stability of the output frequency. These limits usually depend on parameters of internal crystal reference, which are at the same time connected firstly to the temperature and ageing of the crystal itself. For this reason the crystal is heated at a constant temperature of 55C, which guarantees a considerable thermal stability, however a frequency correction due to ageing is easily implemented just manually. The present screen shot allows a very fine adjustment of the frequency value assigned to the radio station without the need to open the transmitter. By entering a correction factor between 0 and 255, the transmitter frequency can be corrected with a 20Hz step only; this operation can be performed during the normal periodical check of the transmitter or, as it is shown below, through a remote telecontrol. By entering the new correction value, its possible to reach a 2KHz offset in comparison to the central value. 4.6.12 PAGE UP for a new screen shot :

In this case its possible to insert the pre-emphasis or to set the transmitter from mono to stereo and vice versa. The pre-emphasis value (50 or 75s) is switched by a jumper placed on the rear window of the rack. The pre-emphasis operates on the LEFT and RIGHT channels only.

Pag. 23

TX50S manual By choosing the STEREO option, the LEFT and RIGHT channels are encoded with the stereo subcarrier addition, from which its possible to get a synchronism in the IN/OUT rear connector (1Vpp sine wave). On the opposite, if an external stereophonic source is already available, the LEFT and RIGHT inputs must be kept free by using the MPX input (rear BNC); in this case the transmitter must be set to MONO even if the transmission is STEREOPHONIC. When the transmission is monophonic, if one enters by the two LEFT and RIGHT channels, the transmitter is modulated at the nominal value; if only one channel is available, this one must enter at the same time both in the LEFT and RIGHT channel inputs, so they must be put in parallel otherwise the deviation would be half of the nominal one. 4.6.13 By entering PAGE UP the following screen shot appears :

Here its possible to see the frequency deviation value and the input signal values. When the composite signal is chosen (addition of all the modulating signals), the numerical and visual indication appearing is the frequency modulation expressed in KHz while on the LEFT, RIGHT MPX signals, the level is measured and displayed as value 100 when it matches the nominal value. The indication states the peak and the chosen measurement will be flashing displayed on the LCD. By modulating the transmitter through the nominal level input signals and with fixed tone (i.e.. 400Hz), the deviation must not exceed 75KHz (COMP) and the input signal level must not exceed 100%. But if a music signal is available at the input, indication can also exceed this value and the exact rules for this check will be seen in the screen shot 11. Besides, if the automatic audio gain control is off, the 75KHz deviation value is equivalent to 100% of the input signal values. On the opposite, if the AGC is on 75KHz deviation can be obtained by an input signal which is variable, as level, from half to the double of the nominal value. 4.6.14 By entering PAGE UP the following screen shot will appear:

Pag. 24

TX50S manual

In this screen shot its possible to enter, if installed, the option of the modulation level automatic control due to the audio signals: when the AGC is on, the maximum modulation value is checked at 75KHz varying the audio amplifiers gain; the dynamic is 6dB and this is useful when the input signal level is not sure. For a wider explanation about the AGC operating see paragraph 4.4. There is also a control on the modulation presence, since everywhere it isnt allowed to transmit by unmodulated carrier; after two minutes of modulation absence an alarm can be given and the power can be disabled. When the modulation returns to the normal value, the alarm stops and the usual operation is restored; in case of stereophonic transmission, the threshold for the modulation absence is 10KHz, because of the subcarrier value. 4.6.15 By entering PAGE UP the following screen shot appear :

Pag. 25

TX50S manual

Pag. 26

TX50S manual

The previous eight screen shots, if selected, allow to perform the measurement of the modulation analysis according to the CEPT 54-01rule. For an exhaustive explanation of this new measurement method see chapter 7. Briefly, it can be said that a music signal can exceed the limit threshold of 75kHhz, provided that this exceeding is contained in a certain percentage. The rules concerning this topic are contained in the above mentioned regulation and in the IEC-244. Thus its possible to quantify the excess of over modulation peak and its possible to show, as in the appendix, that the numerical factor K fixing this limit can not be greater than 0.2. Modulation power on the opposite can not be higher than the one relating to a sine signal deviating 19KHz (reference =0dB) The observation period, for the measurement and the calculation of these factors, is 1 minute, after that the result will be displayed. For the calculation of the K over modulation peak factor, 1200 samplings are performed during a 60 sec measurement, and the value factor is obviously 0 if no peaks exceed 75KHz. The value 0.2 is acceptable as a higher over modulation limit; the value 0.5 shows that the modulation must be reduced of 1dB at least, values higher than K indicates strong over modulations. For the modulation power, over 10 millions of samplings are performed during the minute of examination and power integral defined in the measurement segment is calculated; the result is compared to the one equivalent to a sine signal which deviates 19KHz; the result of the comparison is expressed in dB and it must not be higher than 0, in order to make the measurement complying with the rule. This limit is debatable and, as it has been described in chapter 7, normally in on-field measurements the values of 2,3dB are found which, after all, we estimate dont cause over modulations. Since the peak modulation values are random (they depend, besides on the set levels, on the type of musical pieces as well), K or PM values can remarkably vary during the day relating to the type of the transmitted program; its useful to do many measurements at different times by trying to Pag. 27

TX50S manual

measure dance-music rather than spoken. By using the Personal-Computer interfaced with COM1 placed on the front panel its possible to perform this measurement with many hours of observation periods as it will further be seen. 4.6.16 By entering PAGE UP the following screen shot is accessed:

Here the transmitter internal clock which is used for the memorisation of all the events can be set. At the top the current date appears, the new date at the bottom; in left to right order month, day, year, hours, minutes, seconds appear. 4.6.17.1 By entering PAGE UP the next page is accessed:

By pressing three times the ENTER button, all the alarms in the memory are erased. By entering PAGE UP, the start position is restored.

Pag. 28

TX50S manual

CONNECTION DIAGRAM

Pag. 29

TX50S manual

CIRCUITS DESCRIPTION
5.1 AUDIO-IN board
The AUDIO-IN board has the task to interface the input audio signals with the modulator. Level adjustments are performed on the m, as well as pre -emphasis insertion and input impedance selection. The outputs, going through a flat-cable to the mother board, are raised to a high level and made balanced in order not to be interfered with the transformer flow dispersion. The LEFT and RIGHT signals available on the connectors placed on the rear panel enter, after a first RF noise filter, respectively into U6 and U1. By the U11 switch and the Z1 jumper accessible at the back, the input impedance can be selected (600 or 10k). A similar function is performed by the jumpers Z3, Z4, Z5, Z6, which allow to select the input nominal value level; on the two channels MONO examined, the switches U13 and U12 change the gain by switching three resistances or a trimmer to put the input level to 0, 4.1, 6dBm or by RT3 and RT4 to a level between 6 and +12dBm. The signal is then the pre-emphatized; the value 50s or 75s is chosen by the jumper Z2, while the possible inserting is controlled by the front keyboard. Through U3 and U4 the LEFT and RIGHT channels output is made differential. The MULTIPLEX external signal path is simpler. On it, its only adjusted the level at the nominal value by U16, still controlled by Z3, Z4, Z5, Z6. U9 adds up the MPX signal with the two SCA signals and generates the balanced output signal. Normally, on the SCA signals its difficult to establish an input nominal level since their contribution to the frequency deviation is variable and depends both on the number of subcarriers between 53 and 100KHz and on the difference about MONO or STEREO transmission. In any case, the total deviation of all the subcarriers (19KHz, SCA1, SCA2) must not exceed 10% of the maximum nominal deviation, which in most cases is 75KHz. If the transmitter is monophonic and only the RDS signal placed in one of the two SCA inputs is present, the deviation level of the transmitted data can reach 7,5KHz; whereas if the transmitter is stereophonic and besides the RDS signal also a lower quality audio channel on a subcarrier is present, for example at 76KHz, the total of each subcarrier deviations cant exceed 7,5KHz. The stereo driving carrier will deviate 4KHz, the RDS signal and the other audio channel will have to deviate, for example, 1,75KHz. For this reason, it has been preferred to make the SCA channel levels independent between the nominal input one of the audio channels. The adjustment is obtained by RT1 and RT2 trimmers always placed on the rear panel. All the set levels are showed in the display and the choice to adopt a parameters manual setting related to the input signals level has been preferred to an easier keyboard setting to avoid a non standard levels setting which makes the servicing or the transmitter replacement problematical. The audio signal level errors must not be cleared on the transmitter, but at a former stage. Normally, every broadcasting station fixes a nominal level for all signals and all the adopted equipment must respect this sole value. As higher is this value, as higher will be the noise immunity, and the signalnoise ratio as well.

Pag. 30

TX50S manual

5.2

SINTD board

SINTD board is placed at the rack centre, directly connected to the mother board from which it can be quickly removed. It has the function of frequency synthesized oscillator (88 108MHz) modulated by the audio composite signal. The FET Q1 is the core of the board and oscillates at the set and controlled frequency. All the techniques to obtain high performances in terms of noise and modulation linearity have been adopted. Moreover for a decade EL.CA already have been adopting these circuits solutions (oscillators with coaxial line) for frequencies even till 3GHz for FM transmitters and audio links. Eight varicaps DV1-DV8 modulate the oscillator being driven by the Q2 low output impedance which reduces Nyquist this way wide band noise produced by the variable capacity diodes; at 1MHz between the carrier, the SSB noise is already better than 145dBc, in accordance to ETSETSI-300-384. The Q3 transistor reduces the flicker-noise due to the power supply; the D3-D4 series doesnt allow the Q1 saturation, while Q4 and Q5 uncouple the oscillator from the following amplification stages. The U14 output has a power of 10dBm. The Q6 transistor leads the oscillator signal into the prescaler of the PLL circuit (U4); this integrated circuit performs all the frequency synthesis functions: its set by U1 ports through the main microprocessor placed on the DLCD board. The reference frequency (10MHz) is produced by Q7; the crystal is kept at a constant temperature by a feedback obtained through U5 and U6; the value 55C is 5C higher than the maximum operating temperature, so allowing to obtain a frequency stability lower than a part per million at the environmental working range 0-45C. The error amplifier of the phase comparator i ternal to the PLL chip is composed by U13 and U2 n and it has a closed loop cut frequency lower than one Hertz, so that the lowest frequencies of the modulating stereophonic signal can maintain a separation higher than 50dB between the two channels. The modulation, coming from the mother board and from the AUDIO-IN board, is simply added to the VCO error voltage, no linearization has been provided to make the deviation constant versus the output frequency; typically the deviation error is contained within 0,1 dB all over 20 MHz band. The oscillator has been carefully shielded to avoid that close transmitters could induce spurious frequencies on the output.

Pag. 31

TX50S manual

5.3

MBA board

The central board has the task to distribute the power supplies and the input and output signals; moreover, the audio filters and the peak-to-peak detector for the different modulation level measurements are implemented in it. Both the left and the right channel signals coming from the AUDIO-IN board through the J7 connector, pass through an elliptic filter made of precision active components; the bandwidth at 0.1dB is 15KHz and the attenuation over 19KHz is higher than 40dB; no adjustment is provided, the resistances have a precision of 0.1% and the capacitors are selected and high quality type. U3, U4, U5 and U6 make the left channel filter, the right one is symmetrical. Another elliptic filter of an lower order clean the MULTIPLEX signal by removing the surious signals created by the switching over 600KHz; however this is a typical L-C placed between the two sections of U1. The two further stages formed of U2 make a phase equalizer (RT2) and a amplitude equalizer (RT3) to compensate the DMPX board errors and the previous filter. The operational amplifier U12 generates the composite signal by adding all the signals; the output of the first section can either enter in the automatic gain control optional board or, in its absence, it enters the U12 second section which acts as a clipper using the saturation and the interdiction of the operational amplifier output circuit. The threshold value is regulated by RT6, this output of this stage enters directly into the frequency modulator placed on the SINTD board. The U17 switch selects the audio signal to be measured which the level is d etected by a peak-topeak detector made by U13, U14, U15. Through the U18 switch, controlled by the DLCD board, the measurement can be of peak or envelope, in accordance to the peak measurements or modulation power. A circuit made of U22 and U23 disables the output power in case of external command (CE) or synthesizer fault. This function is performed through software also and this circuit represents a security guarantee for such an important function.

5.4

AGC board

The task of this board is to guarantee the maximum allowed modulation where is not sure that the input audio signal has a fixed value. This option can be added to the transmitter at any time and, when its present, the Z3 jumper placed on the MBA board must be set to ON. Its adjustment, when enabled, is 6dB around the nominal value and it uses 32 gain variation steps of 0.3dB each approx. The operation is quite simple: a wide band amplifier (U6) has the gain which depends on the R2 - R33 resistive value; these are switched by U2, U3, U4 and U5, they are controlled at their time by the microcontroller U1. The AGCO output audio signal is detected by U7, U8 and U9 and the peak-to-peak value is measured by the microcontroller, which consequently decides which gain must be given to the amplifier. The intervention time of the gain variations is not constant, but its for the input signal value; the gain variation algorithm versus the time is complex in order not to distort the signal, anyhow its possible to say that, when the signal has a level equal to half of the nominal one, in a couple of minutes approximately or little bit more its restored to the nominal value. On the opposite, when it has a value which is the double of the set value, it takes just few seconds to reach the nominal value. Pag. 32

TX50S manual On the board its possible to activate an alarm signal which takes place when the modulation is lower than 10KHz for a period of time longer than two minutes (the level 10KHz has been selected because is a little higher than the value due to the stereo subcarrier). When the modulation absence alarm is on, the output power is removed and the transmitter remains in stand-by until the modulation will be restored.

5.5

HSW board

This circuit provides all the needed voltages for the transmitter operation. The voltage coming from the rectified output of the power transformer (48V peak) is filtered by the capacitor group C1 - - C6 then its reduced at the 28 Volt value by the switching regulator Q3 which is driven by U2 and U3. RT1 regulates the current limitation from 1A to 5A, while RT2 regulates the output voltage at 28V. U1 and Q2 protect the circuit against accidental short circuits, by switching off the driver supply. U1, operational amplifier with low offset, measures the current absorbed by the final through the shunt R40 (PAC output). From the +28VDC voltage which supplies the final by three switching regulators in series, its obtained +15VDC (U5),12VDC (U7), +5VDC (U6). The first and the second voltage feed all the transmitter analogue circuits, whereas the third one feeds the LCD display backlight only. The voltage (+5VDC) which feeds all the logic circuits is obtained in place, for the low CMOS circuits consumption. A small voltage transformer TF1 is directly connected to the power, its 9V output is measured by U9 (MX536a), which detects the true effective value and send it through the second section of U6 to the main microprocessor for the control and visualization. The trimmer RT6 is a fine regulation of the measurement.

5.6

40WN and RFDC boards

These board represent the RF power amplifier and the output stage with the directional coupler. The first two stages adopt typical class A polarized bipolar transistors; here the power adjustment is made by acting on the collector supply. So, by a 0 -12VDC control, a constant power adjustment in Watt/Volt is obtained, which is very important for a control stability. The final stage (Q3) is a MOSFET which can deliver more than 60W output; its B class polarized through RT2. Its neutralized against unwanted oscillations by R21 and R14, R15 and R16. All the circuits are wide band and they do not require any alignment. The adoption of air-coiled inductors has allowed to remarkably reduce the space took by the circuits; moreover all the capacitors used in the output circuit are high quality type. The elliptic low pass filter placed at the output, after the power final stage, removes the harmonics by typically attenuating them more than 80dB. The inductor L19 short-circuits the final transistor, providing an accurate protection in case of discharges coming from the antenna. Pag. 33

TX50S manual

The J2 output of the 40WN module enters the RFDC directional coupler placed in another next metal box. This is made of two lines which are strip-line coupled at 30dB. The forward and reflected power are detected by compensating with accuracy the frequency response of the directional coupler. The continuous voltages so obtained are amplified by U1, which introduces also a thermal compensation to the detecting diodes.

5.7

DLCD board

All the input and output data concerning the transmitter are controlled by the DLCD board, to which also the keyboard and the LCD display control and visualisation board are connected. A Motorola microprocessor 68HC11 controls the whole transmitter through the J1 and J2 connectors: the keyboard is multiplexed by U6 and U9. All the values to be measured are fed to the E port with the proper protections against overvoltages or polarity inversions (DZ1 - - DZ8 diodes). A self supplied clock (U21) is connected to the D port through three lines. The microcontroller serial port is switched by U2 and U25 on the RS232 connector placed on the front panel, on the rear one and on the RS485 port on the rear as well; the driver for RS232 is made of U18 (MAX232), while the one for RS485 is U19 (SN75176). The ports B, C and F of the P are connected to an external 128KB flash memory, where the XPT management program is present, which at any time can be loaded through the front COM1 by any PC. The G port is for all the outputs (pre-emphasis enabling, mono-stereo, alarms, measurement selection, etc.). The two external outputs for the alarms are uncoupled by two reed relays with closed or opened contacts selected by two jumpers placed on the MBA board (Z1 and Z2). A part of the H port is used, as output in PWM, to control the forward and reflected power and the fine correction of the transmission frequency. The PWM mean value is detected with accuracy, to avoid errors due to supply voltage variations or saturation and interdiction of the H port outputs. The operational amplifiers U11, U12, U13 and U14 are part of the powers control circuit The control loop has a cut frequency of several hundreds Hertz, so in few milliseconds the power can be controlled and eventually reduced or eliminated in extreme events. The microprocessor therefore provides to the loop the forward and reflected power reference values, the quantities to be checked are PWR and PWD, coming from the directional coupler, while the over stated operational amplifiers represent the error amplifier. The LCD display, driven by the A port, is a 40x4 alphanumerical characters type and allows an useful displaying of data and transmitter settings.

Pag. 34

TX50S manual

ADJUSTMENTS
6.1 Module HSW power supply

The HSW module, which feeds the whole equipment, has an input voltage of 48Vdc provided from the rectified output of the power transformer, and it provides in output all the needed voltages: +28Vdc, +15Vdc, +5Vdc, 15Vdc. Before switching on for the first time the equipment its necessary to switch off the output connector J1 to adjust and verify all the output voltages. The power supply is placed on the radiator in a vertical position, parallel the transmitter right side. For its adjustment its necessary to dismantle the right lateral by keeping off the two screws which connect it to the front panel and also the other two screws which connect it to the rear panel. After the transmitter has been switched on the voltmeter is to be kept on the pin 12 of J1 (output connector) and RT2 will be adjusted to have 28Vdc. Leading the voltmeter pointer on the pin 13 of J1 RT5 is to be adjusted to have +15Vdc. Then it must be check that the voltages +5Vdc on the pin 6 and 12Vdc on the pin 7 are right. Then the voltmeter is to be connected to the 1 of J1 and RT3 is to be adjusted to have offset void (0 V): this is the output for the current measurement absorbed by the RF final. RT1 must be placed at middle run and it will be adjusted as to limit the final current over 55W output. Once the adjustments have been done J1 will be connected again observing the XPT normal operating.

Pag. 35

TX50S manual The trimmer RT6 is adjusted so that the mains supply voltage measurement (230 or 115Vac) is displayed coinciding to the one that is measured directly on the external line AC power supply.

6.2

40WN Module - RF final power

The RF power module is placed in a vertical position on the radiator, enclosed in a metal box. Its completely in wide band and it doesnt require any component alignment which adapt the input and output impedance of the different stages and antenna. The only required adjustment is for the final and driver bias current.

The SMB connector at 90 which leads the RF input signal to the power amplifier module must be taken off and the trimmer RT1 is adjusted to have a voltage of 0.3V at the resistance ends R11, which corresponds to a 0.3A current. Then the RT2 trimmer is adjusted to have a reading of 1A on the display at the correspondence of the PA value visualisation in second page of the main measurements.

6.3

RFDC module- directional coupler

On the directional coupler, which is the module connected to the antenna connector and enclosed in a metal box placed on the radiator, four trimmers must be adjusted.

Pag. 36

TX50S manual

The SMB at 90 angle w hich drives the RF input signal to the power module is to be disabled and RT4 and RT2 are adjusted, so that the value 0 is displayed on the LCD at the correspondence of the forward and reflected power measurement. At this moment the input power is to be c onnected, at 98MHz frequency with a 25W power will be set, it must be connected a thermal wattmeter at the antenna output and RT3 is set to read on the display, at the correspondence of the direct power, the 25W value, read also on the thermal wattmeter. Then the thermal wattmeter is to be disconnected and replaced with a directional Wattmeter connected without 50 charge as to have all the reflected power. A 5W reflected power is to be set and RT2 adjusted to have the same reading on the measurement instrument.

6.4

MBA module - mother board

On the mother board its possible to perform the modulation width setting, of the stereophonic coded signal levels, the automatic check gain regulation threshold, and the phase compensation and the multiplex signal width. The mother board receives on three connectors the VCO oscillator module (SINTD), the stereophonic coded module and the automatic check gain module. Adjust the trimmer RT4 of the MBA board as to have +8Vdc at R7 ends. Inject a +6dBm signal into the r MPX input, after the same level in the settings window has been ear selected, then adjust the RT5 trimmer to read 75KHz on the measurement main page at the modulation correspondence, by TX in MONO.

Pag. 37

TX50S manual

Inject a 400Hz signal and +6dBm level in the LEFT input, switch into STEREO and adjust RT7 of the MBA board to read still 75KHz deviation also for MPX channel. Adjust also RT1 if the subcarrier deviation at 19KHz is not the 10% of the total and adjust again the previous RT7 trimmer. Adjust the RT1 trimmer of the MBA board so that the limitation is symmetrical, on the upper and lower part of the wave form injected with a level higher than 6dB over the nominal.

Pag. 38

TX50S manual Adjust the RT6 trimmer of the MBA board to fix the clipper intervention threshold at the required value over 75KHz. Adjust the RT1 trimmer of the synthesis board to have the exact frequency deviation with the input nominal level presence. Adjust the RT2 and RT3 trimmer of the MBA board for the maximum stereophonic division.

Pag. 39

TX50S manual

MODULATION MEASUREMENT
7.1 General information
The broadcast reception at frequency modulation is often made difficult because of the networks exceeding crowding; the interferences due to the adjacent channels makes the listening unpleasant. This inconvenient may be caused by a ignoring of the protection rules mentioned in the REC. ITUn R BS.412-7 of which the remarkable graphs reported below:

300KHz far from the program we are listening, it must have a level higher than the maximum of 7dB, if its at 200KHz the field intensity level at the point of listening, will be 6dB lower in monophonic or 7dB in stereophonic.
The graph shows that if the interfering network is at

These values, expressed in dB as protection ratio, assume that the interfering network is broadcasting with the maximum allowed spectrum width and this reaches the maximum at the correspondence of peaks and the maximum modulation power. In a laboratory its possible to simulate the worst example of modulation by modulating the transmitter, instead of dance-music, Pag. 40

TX50S manual with coloured noise as mentioned in the CCIR 559 rule (annex B). The process is described in the IEC 244-13 standard and consists of modulating the transmitter with noise as above, with a deviation equal to 32KHz. This work condition corresponds to the maximum allowed band occupation and to a radio broadcast spreading dance-music which modulates 75KHz. At these conditions (modulated transmitter with coloured noise in accordance to CCIR-559) there is the chance to have a reference of a radiophonic transmitter at frequency modulation which occupies the maximum allowed spectrum and on which its possible to perform all the modulation measurements repeatedly, having some parameters as results which can be applied and compared on the field to modulation measurements of a network which is broadcasting a normal music program. The music signal can not be surely measured by a normal detector with effective or peak value, differently from a fix tone signal. The measurement must be done, being not sinusoidal or other periodical form, detecting the power of the signal self (function proportional to its instantaneous value square) or the peak with very long observation periods.

7.2

Modulation peak analysis measurement

The CEPT 54-01 rule shows, in its paragraph 4.2, how the peak measurement must be performed on the modulation of a frequency modulation transmitter. The maximum deviation peak must be found in a 50msec window, to be sure of catching also modulating frequencies till 20Hz. At each minute 1200 representative peak modulation samples are available. These values, obtained with even many minutes long observation periods, will be placed into a graph in the following manner: on the abscissas, the frequency deviation will be placed with a deep scale of 150KHz on the ordinates the number of samples of the corresponding deviation value will be placed It maybe by extreme examples its possible to explain the concept better. Suppose to modulate the transmitter with a fix tone having a deviation of 75KHz and to perform the peak measurement in object for a period of 10 minutes. Thus 12000 samples all with the value 75 will be obtained: the graph will be of a single vertical line 12000 high and placed on the abscissa 75 (fig. 5.a). On the opposite if we modulate the transmitter for 3 minutes with 20KHz deviation, then for further 3 minutes with 40KHz and at last for further 3 minutes with 50KHz and the observation period fixed at 9 minutes we will obtain 10800 samples 3600 of which will have abscissa 30, other 3600 samples abscissa 40 and the last ones abscissa 50 (fig. 5.b).

Pag. 41

TX50S manual

Now, instead of these simple examples, take our transmitter modulated with the sample noise previously mentioned, and we detect in accordance with the CEPT 54-01 the modulation peak samples in a 30 minutes observation period, so obtaining the graph. 5.c-a whereas, if we increase the modulation, always with the same input signal, of 1dB, well obtain the graph 5.d-a with a 30 minutes observation period:

fig. 5.c-a

fig. 5.c-b

fig. 5.d-a

fig. 5.d-b

On the first graph it can be observed that during the 30 minutes about 2600 peak samples have been measured which have deviated the carrier of 54KHz, 1500 60KHz, 10 75KHz, while about ten samples resulted higher than 75KHz. What has been measured is a signal which respects all the spectrum occupation and over modulation rules; it can be soon noticed that this signal has been higher with its modulation peaks than the threshold of 75KHz for about 0.2% of the samples so its wrong to sustain that this value is never exceeded at all. Relying for the modulation adjustment on the bar-graph of which almost all the transmitters are equipped, one risks to have to under modulate if the trimmer is set to remain within 75KHz.

Pag. 42

TX50S manual In the figures 5.c-b and 5.d-b, as suggested by CEPT 54-01, the Accumulated distribution plot of deviation have been reported on the graph, relating to the graphs of the left figures -a and -b ; in this case all the samples from left to right have been added and the samples total value has been normalized. In other words, starting from left fig. 5.d-a (0KHz) and going towards right (150KHz) its noticed that all the samples are towards right (100 %) till about 35KHz, to 50KHz over than the 80% of samples is on the right, at 70kHhz just the 5% of samples is on the right, as it has been evidenced on the graphs b ordinates. The CEPT 54-01 rule and the equivalent REC. ITU-R SM.1268 and REC. ITU-R BS.412-7, at this point stop and they do not give exact and rigorous information about the interpretation of the graphs mentioned above. On the opposite by connecting the different rules its possible to analyse the graphs of fig. 5.c-a and 5.c-b to draw some statistic parameters which, deriving from a reference system, can, as said previously, be applied to a typical music broadcast. So some quantities will be defined peculiar to the two graphs which will define just one over modulation factor, whose value will be used as limit parameter. Definitions: M OM : : average of all the measured samples as peak maximum every 50msec average of the samples which have exceeded the 75KHz threshold only samples percentage which has exceeded 75KHz as to the total over modulation factor, defined as follows: K = (OM - 75)*OM% /100 The formula can be explained easily and intuitively, since the over modulation factor is directly proportional to the peak number percentage detected over 75KHz (OM%), while the ones lower than this threshold must not give any contribution to K, and its also directly proportional to the peaks KHz value which have exceed 75KHz (OM75). If no maximum peaks measured through the 50msec samples has exceeded 75KHz, we are in a favourable condition, OM = 0 and OM% = 0 and so K = 0 If all the peaks exceed 75KHz and their average is 78 then K = (78 75) * 100 / 100 = 3 Now getting the example again of the transmitter modulated with coloured noise as to the CCIR559 and IEC-244 rules previously seen, which has originated the graphs of fig. 5c-a , 5c-b, 5d-a and 5d-b and we apply the above mentioned parameters and calculate them each minute. Thus it will be obtained other graphs which can be added to the two previous couples, so originating a screen shot full of all the parameters relating to the peak modulation measurement:

OM% : K :

Pag. 43

TX50S manual

fig. 5.e

fig. 5.f Examine the graphs of. 5.e, which could correspond to the modulation peak analysis of a regular transmitter which doesnt over modulate: in these each minute M, OM, OM% values have been

Pag. 44

TX50S manual

calculated and consequently the K factor. It can be noticed that K value constantly keeps each minute below the value 0.01. So assume this value as limit for the over modulation factor. Increasing the modulation of 1dB the graphs in fig. 5.f are given, corresponding to a transmitter which deviates little more than 8KHz; in this case K value is 0.11. Thus it can be noticed that for small modulation values higher than 75KHz, K increases considerably. The rules rightly have tried to fix some limits for the instruments accuracy which need to perform this kind of measurements, but the system weakness is surely constituted by the receiver, with all its problems concerning the answer to quick transitory and also the peaks, which is almost ever distorted by the medium and low frequency filters group delaying with over elongations or miscompensated attenuation. So it would be ideal to draw the modulating signal, which is usually available on all the transmitters, performing all the measurements on it, after having made sure of the exact relation between the audio level and the frequency deviation. In the TX50S this is automatic and we think if a modulation peak analysis measurement made far from the transmitter, has produced doubtful and questionable results, it must be repeated by the instrument inside the transmitter like in the TX50S. The measurement must be started for a whole day observation period so to pick up the programs having most over modulation problems and consequently to act on the dynamic limitercompressor every study must have. With this measurement method help its possible to set best the limitercompressor no longer by ear but by real data and no more subjective elements.

7.3

Modulation power measurement

Another important parameter determining the interference intensity on the adjacent channel is the modulation power value. The term is not of common use and the idea that the modulation power can influence the interferences is not easy to understand. Reading the CEPT 54-01 rule its noticed that the transmitter modulation power in object must not exceed the samples reference signal one, represented by a sinusoidal signal which deviates 19KHz of peak. The 19KHz value has no relation with the stereophonic subcarrier value but its the frequency deviation which the sample signal creates on the transmitter. On the tuned receiver this signal will be carried to the loudspeaker with a certain voltage directly proportional to the deviation value; then there will be a certain electric power on the loudspeaker equal to the effectual voltage square about divided into the loudspeaker impedance; it, at less of the diffuser efficiency, coincides to the acoustic power. So its possible to believe the modulation power as the equivalent of the acoustic power spread by the loudspeaker, and perceived by our ears. Thus as for the electric power, the equivalent mathematical rules are valid for the modulation power also. In the first case the value depends on the voltage square, in the second one on the deviation square. Pag. 45

TX50S manual

In the case of a sinusoidal quantity, which may be voltage or deviation, the power is calculated for a time equal or multiple the semi period of the wave form, while in the case of a music signal the calculation is to be made by the integral which defines the power. Besides the modulation power value in absolute form would be of a difficult understanding, for this reason any sinusoidal signal is taken as reference whose power, for long observation periods, doesnt depend on the sinusoid frequency but only on its peak value square. So the rule provides to measure the modulation power, which is as previously seen equal to modulating signal electric power, for one minute time period and to compare it to a sinusoidal modulating signal one which deviates 19KHz. The result, expressed in dB, must be lower or equal to zero to comply the rule. The modulation power integral calculation is made inside the transmitter by integrating, between 0 and 1 minute, the modulating signal square. The integration is made in a discreet manner by calculating the function area in the integration time; the signal sampling is made at a double speed respecting its bandwidth, so microprocessor is practically locked for a minute to follow instant by instant MPX signal value. After this period it performs the set values square, add them up, which is equal to the integral, then it calculates the logarithm respecting the reference sinusoidal value. The value is displayed in a numerical form or on a graph (on the PC) which has in the abscissas the time (discreet with 1min steps) and in the ordinates the value in dB of the music signal power and the reference sinusoidal one ratio. Even in this case its possible to refer to a modulating signal made of the usual coloured noise in accordance to CCIR-559 particularly Rec.ITU-R BS.412-7 mentions at pag.5-note 4: The power of a sinusoidal tone causing a peak deviation of 19KHz is equal to the coloured noise modulation signal according to Recommendation ITU-R BS.641 , i.e. a coloured noise signal causing a quasi-peak deviation of 32KHz So, for the modulation power measurement instrument alignment, its possible to refer either to a 500Hz sinusoidal signal (the frequency is not important) which makes the carrier to deviate of 19KHz or to the coloured noise which deviates 32KHz. Both signals give the listening the same sensation of volume intensity , told in non technical words and not considering physiological effects of the ear sensibility at the different frequencies.

7.4

Considerations on the real measurements performed

Performing modulation measurements with the methods described so far on broadcast networks which have been modulating for years without over modulation problems, one realizes how the limits imposed by the rules mentioned so far are particularly restrictive and maybe not in compliance with current reality. There are some contradictions and gaps the rules self sometimes point out. We report two examples which give the idea of the real difficulty about the strict application of them:

Pag. 46

TX50S manual REC. 641 , Rep.1064 5. FREQUENCY DEVIATION OF THE SIGNAL GEN. ...................The unwanted transmitter L is then modulated with a 500 Hz sinusoidal tone obtained from audio generator A. Attenuator B is then adjusted to obtain a deviation of 32 KHz. The audio frequency level as the input of the unwanted transmitter before the pre-emphasis is now measured by means of the noise voltmeter U. The noise-weighting network is switched off. Next, a noise signal C+D replaces the sinusoidal tone, and attenuator E is adjusted to obtain the same peak-reading as before at the noise voltmeter. The quasipeak deviation is thus equal to 32 KHz. Since the preemphasis has not been included in the level measurement, the actual peak deviation is higher .The described adjustment corresponds to the present-day broadcasting practice. Note. A normal sound-broadcasting programme without compression is simulated by modulating the unwanted transmitter with the standardized coloured noise signal using a frequency deviation of 32 KHz. Therefore, the results obtained with this method and this deviation are only valid for sound broadcasting programmes without compression.

The not considering the pre-emphasis leads to a difference of 1dB about, whereas the audio compressors installed now in every broadcast networks increase the modulation power of 2dB further on. If a stereophonic signal is being examined the Rec.ITU-R BS.412-7 is very clear and it makes no distinction between the modulation power within monophonic and stereophonic signal: Rec. ITU-R BS.412-7 2.3 The radio-frequency protection ratios assume that the maximum peak deviation of 75 KHz is not exceeded. Moreover, it is assumed that the power of the complete multiplex signal including pilot-tone and additional signals , integrated over any interval of 60 s is not higher than the power of a MPX signal containing a single sinusoidal tone which causes a peak dev. of 19 KHz (see Note 4 ) ............................................................................................. Note 4 The power of a sinusoidal tone causing a peak dev. Of 19 KHz is equal to the power of the coloured noise modulation signal according to ITU-R BS.641 i.e. a coloured noise signal causing a quasi-peak deviation of 32 KHz .

Whereas the IEC 244-13 makes a difference between monophonic signal (reference of 32KHz) and stereophonic one (40KHz): IEC 244-13 witch 9.4 For monophonic operation Check that the pre and de-emphasis filters are in circuit Adjust the output of the LF generator at <1KHz to a level corresponds to a frequency dev. 7.4 dB below maximum rated Pag. 47

TX50S manual deviation ( 32 KHz for 75 KHz dev.) Measure the peak value by means of the noise meter at the out of the demodulator ( without weighting network). Switch the LF generator out of circuit and the noise generator in circuit and adjust the output of the noise generator , so that the noise meter gives the same reading. The peak-dev. is now correct. ............................................................................................... ............................................................................................... For stereophonic operation Check that the appropriate pre and de-emphasis are in circuit Adjust the output of the LF generator at <1KHz to a level corresponding to a frequency deviation of 40 KHz including pilot tone. Measure the peak value in channel B after the demodulator and stereo encoder by means of the noise meter (without the weighting network ). For the remaining procedure , see the method used for monophonic operation In case of stereophonic broadcast in accordance to the IEC 244-13 rule the reference power is moved highwards of 1.9 dB in relation to the corresponding REC. ITU-R BS.412-7.

Pag. 48

TX50S manual

REMOTE CONTROL
8.1 PC connections

The transmitter can be connected to a Personal Computer through a three wires serial cable. There are three serial ports: the first (COM1), placed on the front panel works as monitor for a connection to a PC, the second (COM2), placed on the back needs for the connection to a possible power amplifier, with the third (COM3) its possible to connect a modem linked to a telephone line or to do the connection of N+1 transmitters. The PC must have: processor Operative system RAM Non volatile memory Graphic CD reader : : : : : PENTIUM o sup. WIN3.1 / WIN95 / WIN98 32MB 32MB SVGA 600x800/768x1024

8.2

COM1

If one wishes to connect a PC to replace the transmitter keyboard and thus have a wider and easier communication to every visualisation and control function, its possible to connect the DB9 front port (COM1) to a serial cable with at least three wires to the serial port of a personal computer where the communicating software provided on the transmitter enclosed CD has been already loaded. If unready it is sufficient to start the SETUP and automatically the software is installed as to create an icon (XPT-50), which will need for the program start. Once started it will appear on the display:

Pag. 49

TX50S manual

The screen cursor which displays the modulation will be still and the low left inscription RS232 Connection will show: not connected. At this point it is essential, after the transmitter has been switched on, to make it communicate. So the transmitter keyboard blue button marked as REMOTE 232 must be entered The following page will appear on the display:

which indicates that by default the COM1 connection has been chosen instead of the COM3 and on the COM2 no power amplifier is connected. If on the COM2 an amplifier was connected automatically it would be detected and its caption would appear beside the COM2 one. If a modem connected to the telephone line is to be connected it needs to select by the horizontal cursor and the data key the COM3. If the selected options are right, pressing ENTER the communication to the PC connected to the COM1 is entered, the blue key led switches on, on the display the cursor moves from left towards right, displaying the modulation peaks as an oscilloscope and the caption connected will appear on the left bottom. The first page is just an introduction to the system, of which its possible to know the options installed or the hour of the last switching on. At the right bottom of the display there is a grey window with an arrow and if it is entered its possible to enter into the following pages:

Pag. 50

TX50S manual

The second page allows to know all the transmitter operation data: frequencypower etc., without the possibility to modify them. Choosing by the lower arrow the third page the data displaying of the input low frequency signal and modulation can be entered:

All the pages have different coloured windows to divide the width measurements from the setting of them. On the top of this page its possible to check which channel is displayed on the screen shot (COMPOSITE); to change this display because, for example, one wants to check the LEFT course, one must enter the lower window (MODULATION SETTINGS), and press DATA SETTING ENTER. The red button will switch on, the modulation will disappear and changing in the window Channel Modulation, the respective changes will be displayed on the higher window too. When the chosen data are the requested ones its possible to switch the red button off and the normal displaying will be restored. Selecting the fourth page the power settings are entered: Pag. 51

TX50S manual

Here also the settings are distinguished from the measurements by a different colour. To change data it is sufficient to press the red button, which will lighten, and will change data in the RF POWER SETTING window. At every new setting a changing of the measurement displayed above will correspond. On the top right window also the power final stage parameters are reported. Choosing the next page there will be:

Here the transmitter clock settings and frequencies can be changed. Pag. 52

TX50S manual Differently from the previous pages, here the variations cannot be performed in real time, to avoid the transmitter goes on unwanted frequencies. So, at first data must be inserted then the red button must be pressed to enter them. During the frequency change power is disabled for few seconds and the oscillator anomalous condition is not stored as alarm. If an out-of-channelization frequency is entered, the item is ignored. It is also possible a fine frequency correction, to correct the crystal ageing by inserting a number included between 0 and 255 and checking by a frequency-meter connected to the RF monitor. The following page allows the alarm displaying and erasing:

The quantities controlled by this function are: MAINS SUPPLY VOLTAGE CURRENT ON THE RF FINAL VOLTAGE ON THE RF FINAL RF FINAL RADIATOR TEMPERATURE MODULATION ABSENCE SYNTHESIZED OSCILLATOR ANOMALOUS OPERATING EXTERNAL CARRIER ENABLE Whenever the limits joined to each quantity mentioned above are exceeded, the output power is taken off, a visual signalling and ON/OFF contacts are given and the event is stored and associated to the date when it has occurred.

Pag. 53

TX50S manual

Besides the ceased alarms are stored as to know the output power absence period. As for the keyboard, the alarms can be erased. The last pages are dedicated to the modulation analysis measurement (power and peak):

Pag. 54

TX50S manual

As appendix the whole theory concerning this kind of measurements is dealt in chapter 7, dedicated to the modulation measurements. In the upper graphs the peak modulation statistic parameters of a broadcast network observed during 10 minutes period are reported. It can be observed that the 12000 peak measurement samples detected lead to consider that the network is on the limit of the allowed deviation; the last K diagram clearly shows the spoken broadcasting for the first two minutes followed by a music passage (K>4), at the end other two minutes spoken (K<3). By entering HELP on the window the followed rule appears (CEPT 54-01). The observation time period is edited in ANALYSIS TIME followed by START.

Pag. 55

TX50S manual

TX50S INTERNAL ADJUSTMENTS & SETTINGS

See figg. 9.a , 9.b , 9.c for function number Board name/ N Component 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 MBA/RT7 DMPX/C22 DMPX/RT1 DMPX/RT3 DMPX/RT2 DLCD/Z1 DLCD/P9 DLCD/BT1 DLCD/Z2 MBA/RT5 MBA/RT4 AGC/RT1 MBA/RT1 MBA/RT6 MBA/RT2 MBA/RT3 FUNCTION MPX frequency deviation Pilot frequency Pilot level Pilot phase MPX spurious Run/Boot MCU reset Clock battery Password Freq.dev.display Pilot THD AGC level input Clipper symm. Clipper level Chan. separation Chan. separation Mono frequency deviation Frequency Line voltage meas. PAC meas. +28Vdc +15Vdc PAC limiter PWR offset PWR meas. PWD meas. PWD offset Final RF mosfet current meas. Driver current DESCRIPTION Adjust, with nominal MPX input level, for 75 Khz frequency deviation Adjust stereo subcarrier to 19 Khz +/-1Hz Adjust to 20dB less than MPX signal Adjust to the right phase by antiphase tecnique Adjust for minimum spurious of MPX signal Set jumper to RUN for normal operation, to BOOT for firmware loading ( by COM1 ) Press button to Reset 68HC11 microcontroller Use only 3.3 V lithium battery (WARNING:TOXIC COMPONENT) Set jumper to PASSW. to enable password function. Adjust to display modulation = 75 Khz on Page 0 Adjust to minimum pilot THD Adjust, with nominal LF level input, DC voltage on DZ1 to 2.6V Adjust for clipper symmetry Adjust to the desired clipper level Adjust for max channel separation Adjust for max channel separation Adjust, with nominal mono audiolevel in MPX input, for 75 Khz deviation Adjust to right output frequency with fine frequency number set to 100 Adjust to display on page 0 line voltage measured between M2 connector pins on HSW board Adjust to 0Vdc on PAC (J1-1) without connector Adjust to 28 Vdc (J1-12) Adjust to 15 Vdc (J1-13) Rotate completely clockwise for Ilim>5A (max value) Adjust to obtain (without RFin) 0Vdc on PWR feedthrough Adjust to read on display (without RF load) PWD=PWR (PWR set = 5W) Adjust to obtain Pout = 50W (PWD set = 50W) Adjust to obtain (without RFin) 0Vdc on PWD feedthrough Adjust to read (without RF) PACurrent=1A on display page1 Adjust to obtain (without RF) 35mVdc voltage drop on R11

16 SINTD/RT1 17 SINTD/CV1 18 19 20 21 22 23 24 25 26 27 28 HSW/RT6 HSW/RT3 HSW/RT2 HSW/RT5 HSW/RT1 RFDC/RT2 RFDC/RT1 RFDC/RT3 RFDC/RT4 40WN/RT2 40WN/RT1

Pag. 56

TX50S manual

Pag. 57

TX50S manual

Pag. 58

TX50S manual

Pag. 59

TX50S manual

TX50S
See fig. 9.d

REAR CONNECTIONS & SETTINGS

for function number

FUNCTION

CONNECTION 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 NC NC NC NC GND EXTERNAL PWD EXTERNAL PWR NC NC NC NC NC NC GND I1 I2 NC NC NC RX ( amplifier ) TX ( amplifier ) NC GND NC NC NC NC NC INPUT RS485 + INPUT RS485 NC GND NC NC NC NC

AUX IN/OUT

PIN NUMBER ( DB9 )

AES/EBU IN

PIN NUMBER ( DB9 )

COM2 RS232 to power amplifier

PIN NUMBER ( DB9 )

COM3A RS485 to remote control (external Modem) or N+1 system

PIN NUMBER ( DB9 )

Pag. 60

TX50S manual

FUNCTION

CONNECTION
1 2 3 4 5 6 7 8 9 1 2 3 PIN NUMBER ( DB9 ) NC INPUT RS485 + INPUT RS485 NC GND NC NC NC NC 19 Khz sync. out ( 1 Vpp out ) EX Carrier enable input (input contact
open = enable) ALARM1 out (closed or open output contact / Z1, Z2 - MBA board ) ALARM2 out (closed or open output contact / Z1, Z2 MBA board )

COM3B RS485 to N+1 system

PIN NUMBER ( DB9 )

IN/OUT

7 8 9 10 11 12 13 14 15 16 17 18 19

EXTERNAL MONO / MPX INPUT ADJUSTMENT SUBCARRIER 1 INPUT ADJUSTMENT SUBCARRIER 2 INPUT ADJUSTMENT NOMINAL VALUE LF INPUT SETSETTING PREEMPHASIS VALUE CHOICE MONO INPUT ( L / R ) IMPEDENCE CHOICE LEFT INPUT ADJUSTMENT RIGHT INPUT ADJUSTMENT SCA1 & SCA2 INPUTS EXTERNAL MPX INPUT LEFT INPUT RIGHT INPUT RF OUT

5 GND 6 NC 7 NC 8 NC 9 NC Trimmer RT5 / AUDIO IN board -6 / +12 dBm adj. for 75 Khz modulation frequency Trimmer RT1 / AUDIO IN board -20 dBu adj. Trimmer RT2 / AUDIO IN board -20 dBu adj. Jumpers Z3,Z4,Z5,Z6 / AUDIO IN board 0 , 4.1 , 6 , variable (-6/+12) dBm setting choice Jumpers Z8,Z2 / AUDIO IN board 50 / 75 microseconds choice Jumpers Z1,Z7 / AUDIO IN board 600 Ohm / 10 Kohm choice Trimmer RT4 / AUDIO IN board -6 / +12 dBm adj. for 75 Khz modulation frequency Trimmer RT3 / AUDIO IN board -6 / 12 dBm adj. for 75 Khz modulation frequency BNC connector

PIN NUMBER (Cannon) PIN NUMBER (Cannon)

1 2 3 1 2 3

BNC connector GND LEFT + (unbalanced with GND) LEFT (balanced with LEFT+) GND RIGHT + (unbalanced with GND) RIGHT (balanced with RIGHT+) N connector

Pag. 61

TX50S manual

Fig. 9.d

Pag. 62

TX50S manual

DIAGRAMS AND LAYOUTS

Pag. 63

TX50S manual

HSW BOARD - POWER SUPPLY

Pag. 64

TX50S manual

HSW BOARD - POWER SUPPLY

Pag. 65

TX50S manual

HSW BOARD - POWER SUPPLY

|qty |part number |Val 1 |1 |BAR10 2 |1 |CCM_1u 3 |1 |CCM_1u 4 |1 |CCM_1u 5 |1 |CCM_1u 6 |1 |CCM_1u 7 |1 |CCM_1u 8 |1 |CCM_2n2 9 |1 |CCM_2u2 10 |1 |CCM_2u2 11 |1 |CCM_3n3 12 |1 |CCM_10n 13 |1 |CCM_56p 14 |1 |CCM_100n 15 |1 |CCM_100n 16 |1 |CCM_100n 17 |1 |CCM_100n 18 |1 |CCM_100n 19 |1 |CCM_100n 20 |1 |CCM_100n 21 |1 |CCM_100n 22 |1 |CCM_100n 23 |1 |CCM_100p 24 |1 |CCM_220n 25 |1 |CEV_10u-25V 26 |1 |CEV_10u-25V 27 |1 |CEV_10u-25V 28 |1 |CEV_47u-25V_EKR 29 |1 |CEV_47u-25V_EKR 30 |1 |CEV_47u-25V_EKR 31 |1 |CEV_47u-25V_EKR 32 |1 |CEV_47u-25V_EKR 33 |1 |CEV_47u-25V_EKR 34 |1 |CEV_47u-25V_EKR 35 |1 |CEV_47u-25V_EKR 36 |1 |CEV_220u-25V_EKR 37 |1 |CEV_220u-25V_EKR 38 |1 |CEV_220u-63V_EKR 39 |1 |CEV_220u-63V_EKR 40 |1 |CEV_220u-63V_EKR 41 |1 |CEV_220u-63V_EKR 42 |1 |CEV_470u-35V 43 |1 |CEV_1000u-100V 44 |1 |CEV_1000u-100V 45 |1 |CEV_1000u-100V 46 |1 |CEV_1000u-100V 47 |1 |CEV_1000u-100V 48 |1 |CEV_1000u-100V 49 |1 |DROP_NC 50 |1 |IRF540 51 |1 |IR2125 52 |1 |J156X14 Poli|J1| 53 |1 |LM3578 54 |1 |LTUBE-D8P5 55 |1 |LTUBE-D8P5 56 |1 |LTUBE-D8P5 57 |1 |LTUBE-D8P5 58 |1 |LTUBE-D8P5 59 |1 |LTUBE-D8P5 60 |1 |LT1074CT 61 |1 |LT1074CT 62 |1 |LT1376-5 63 |1 |L_TORO_100uH 64 |1 |L_TORO_100uH 65 |1 |L_TORO_250uH 66 |1 |L_TORO_250uH 67 |1 |MBR1045 68 |1 |MBR1045 69 |1 |MM_02V 70 |1 |MM_05V 71 |1 |MPSA06 72 |1 |MPSA06 73 |1 |MX536A 74 |1 |OP07N 75 |1 |RFILM5W 76 |1 |RFILM5W 77 |1 |RFILM5W 78 |1 |RT_72P 79 |1 |RT_72P 80 |1 |RT_3296W 81 |1 |RT_3296W |Tol | |1u |1u |1u |1u |1u |1u |2n2 |2u2 |2u2 |3n3 |10n |56p |100n |100n |100n |100n |100n |100n |100n |100n |100n |100p |220n |10u |10u |10u |47u |47u |47u |47u |47u |47u |47u |47u |220u |220u |220u |220u |220u |220u |470u |1000u |1000u |1000u |1000u |1000u |1000u | | | | | |1mH |1mH |1mH |22uH |22uH |1mH | | | |100uH |100uH |250uH |250uH | | | | | | | | |0.22 |0.22 |0.1 |10k |1k |500 |200 |Work.Volt.|description | |diode |D10| | |Multilayer Ceramic Capacito |C8| | |Multilayer Ceramic Capacito |C22| | |Multilayer Ceramic Capacito |C23| | |Multilayer Ceramic Capacito |C26| | |Multilayer Ceramic Capacito |C31| | |Multilayer Ceramic Capacito |C36| | |Multilayer Ceramic Capacitor|C14| | |Multilayer Ceramic Capacitor|C20| | |Multilayer Ceramic Capacitor|C29| | |Multilayer Ceramic Capacitor |C9| | |Multilayer Ceramic Capacitor|C11| | |Multilayer Ceramic Capacitor|C10| | |Multilayer Ceramic Capacitor |C7| | |Multilayer Ceramic Capacitor|C13| | |Multilayer Ceramic Capacitor|C21| | |Multilayer Ceramic Capacitor |C19| | |Multilayer Ceramic Capacitor |C39| | |Multilayer Ceramic Capacitor |C30| | |Multilayer Ceramic Capacito |C37| | |Multilayer Ceramic Capacitor |C38| | |Multilayer Ceramic Capacitor |C46| | |Multilayer Ceramic Capacitor |C12| | |Multilayer Ceramic Capacitor |C32| |25V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C40| |25V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C28| |25V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C27| |25V | |C45| |25V | |C33| |25V | |C34| |25V | |C35| |25V | |C43| |25V | |C41| |25V | |C44| |25V | |C42| |25V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C24| |25V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C25| |63V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C16| |63V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C17| |63V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C15| |63V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C47| |35V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C18| |100V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C1| |100V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C2| |100V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C3| |100V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C4| |100V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C5| |100V |ALUM. RADIAL ELCTROLYTIC CAPACITOR|C6| | | |Z2| | |N-Channel Power MOSFET TO220 |Q3| | |CURRENT LIMITING CHANNEL DRIVER |U3| | |Connettore Passo 3.96mm (156th) 14 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |SWITCHING REGULATOR |U2| |Inductor Tube Diametro 8.5mm Passo 5mm PTH|L5| |Inductor Tube Diametro 8.5mm Passo 5mm PTH|L7| |Inductor Tube Diametro 8.5mm Passo 5mm PTH|L6| |Inductor Tube Diametro 8.5mm Passo 5mm PTH|L8| |Inductor Tube Diametro 8.5mm Passo 5mm PTH|L9| |Inductor Tube Diametro 8.5mm Passo 5mm PTH|L10| | |U7| | |U5| |1.5A, 500KHz STEP-DOWN SWITCHING REGULATOR |U8| |TOROIDE AVVOLTO 100uH 5 AMPERE |L2| |TOROIDE AVVOLTO 100uH 5 AMPERE |L4| |TOROIDE AVVOLTO 250uH 5 AMPERE |L1| |TOROIDE AVVOLTO 250uH 5 AMPERE |L3| |Diode MBR1045 Case DO220AB |D4| |Diode MBR1045 Case DO220AB |D6| | |M2| | |M1| |Transistor, NPN BJT |Q2| |Transistor, NPN BJT |Q1| | |U9| |ULTRA-LOW-OFFSET-VOLTAGE OPERATIONAL AMPLIFIER |Film Resistor Mounted with dissipator|R11| |Film Resistor Mounted with dissipator|R12| |Film Resistor Mounted with dissipator|R40| |Trimmer Cermet Monogiro serie 72P Beckman|RT1| |Trimmer Cermet Monogiro serie 72P Beckman|RT5| |Trimmer Cermet Multigiro serie 3296W Bourns|RT3| |Trimmer Cermet Multigiro serie 3296W Bourns|RT6|

| |20% |20% |20% |20% |20% |20% |10% |20% |20% |10% |10% |5% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% | | | | | | | | | | | | | | | | | | | | | | | | | | |% |% |% |10% |10% |10% |10%

Pag. 66

TX50S manual
82 83 84 85 86 87 88 89 90 91 92 93 94 95 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |RT_3296W |R05-J-68R |R05-J-68R |R025-J-1K0 |R025-J-1K0 |R025-J-1K0 |R025-J-1K2 |R025-J-1K5 |R025-J-2K2 |R025-J-2K2 |R025-J-2K2 |R025-J-2K7 |R025-J-2K7 |R025-J-3K3 |R025-J-10K |R025-J-10K |R025-J-10K |R025-J-15K |R025-J-22K |R025-J-22K |R025-J-47R |R025-J-56K |R025-J-000 |R025-J-100K |R025-J-100K |R025-J-100K |R025-J-100K |R025-J-100R |R025-J-100R |R025-J-270R |R025-J-270R |R025-J-270R |R025-J-390R |R025-J-560R |R025-J-680R |R025-J-680R |TLC27L2N |TMP37 |TP1_1 |TP1_1 |TRF_ELCA01 |ZPD5V1 |ZPD12V |ZPD15V |1N4001 |1N4001 |1N4148 |1N4148 |1N5818 |1N5818 |74HC14N |500 |68R |68R |1K0 |1K0 |1K0 |1K2 |1K5 |2K2 |2K2 |2K2 |2K7 |2K7 |4K7 |10K |10K |10K |15K |22K |22K |47R |56K |0R82 |100K |115K |100K |100K |100 |100 |270R |270R |270R |390R |820R |680R |680R | | | | | | | | | | | | | | | |10% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |V | | | | | | | | | | | | | |Trimmer Cermet Multigiro serie 3296W Bourns|RT2| |RESISTOR - Metal Film |R18|COD |RESISTOR - Metal Film |R17|COD |RESISTOR - Metal Film 0.25 W |R26| |RESISTOR - Metal Film 0.25 W |R29| |RESISTOR - Metal Film 0.25 W |R33| |RESISTOR - Metal Film |R16| |RESISTOR - Metal Film |R21| |RESISTOR SMD 0805 |R8| |RESISTOR - Metal Film |R10| |RESISTOR - Metal Film |R41| |RESISTOR - Metal Film |R15| |RESISTOR - Metal Film |R20| |RESISTOR - Metal |RESISTOR - Metal Film |R30| |RESISTOR - Metal Film |R35| |RESISTOR - Metal Film |R37| |RESISTOR - Metal Film |R31| |RESISTOR - Metal Film |R22| |RESISTOR - Metal Film |R36| |RESISTOR - Metal Film |R9| |RESISTOR - Metal Film |R7| |RESISTOR - Metal Film |R44| |RESISTOR - Metal Film |R13| |RESISTOR - Metal Film |R19| |RESISTOR - Metal Film |R38| |RESISTOR - Metal Film |R45| |RESISTOR - Metal Film |R24| |RESISTOR - Metal Film |R23| |RESISTOR - Metal Film |R25| |RESISTOR - Metal Film |R32| |RESISTOR - Metal Film |R39| |RESISTOR - Metal Film |R43| |RESISTOR - Metal Film |R42| |RESISTOR - Metal Film |R2| |RESISTOR - Metal Film |R28| |Precision Dual Operational Amplifiers DIP8|U6| | |U10| | |R18A| | |R17A| | |TF1| |Zener Diode 0,5 W - 5.1 V |DZ3| |Zener Diode 0,5 W - 12V |DZ2| |Zener Diode 0,5 W - 12V |DZ1| |General Purpose Rectifier |D2| |General Purpose Rectifier |D5| |General Purpose Rectifier 0,1 A |D3| |General Purpose Rectifier 0,1 A |D9| |Diode Schottky 3A |D7| |Diode Schottky 3A |D8| |IC, Hex Inverter Schmitt-Trigger |U1|

Pag. 67

TX50S manual

AUDIOIN BOARD - AUDIO INPUTS

Pag. 68

TX50S manual

AUDIOIN BOARD - AUDIO INPUTS

Pag. 69

TX50S manual

AUDIOIN BOARD- AUDIO INPUTS

Pag. 70

TX50S manual

AUDIOIN BOARD- AUDIO INPUTS

item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 |qty |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |part number |BERG100F1X06V |BERG100M1X02V |BERG100M1X02V |BERG100M1X03V |BERG100M1X05V |CPVP_6n8_63V |CPVP_6n8_63V |C1210_1n |C1210_1n |C1210_1n |C1210_1n |C1210_1n |C1210_1n |C1210_1n |C1210_1n |C4051BD |C4051BD |C4051BD |C4052BD |C4052BD |C4052BD |C4532BD |JFL_26M |LL4148 |LL4148 |LL4148 |LL4148 |LL4148 |LL4148 |LL4148 |LL4148 |LL4148 |LL4148 |LL4148 |LL4148 |LL4148 |LL4148 |L1812_1mH |L1812_1mH |L1812_1mH |L1812_1mH |L1812_1mH |L1812_1mH |L1812_1mH |L1812_1mH |L1812_1mH |PIN_WIRE |PIN_WIRE |PIN_WIRE |RT_72P |RT_72P |RT_72P-20K |RT_72P-20K |RT_72P-20K |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |R1206-F-2K22 |Val | | | | | |6n8 |6n8 |1n |1n |1n |1n |1n |1n |1n |1n | | | | | | | | | | | | | | | | | | | | | | |1mH |1mH |10uH |10uH |10uH |10uH |10uH |10uH |10uH | | | |10K |10K |20K |20K |20K |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |2K22 |Tol | | | | | |10% |10% |20 |20 |20 |20 |20 |20 |20 |20 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |10% |10% |10% |10% |10% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |Work.Volt.|description | | |Physical Connector | |Physical Connector | |Physical Connector | |Physical Connector | |Physical Connector |63V |capacitor |63V |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |Multiplexer, Analog 8-Bit | |Multiplexer, Analog 8-Bit | |Multiplexer, Analog 8-Bit | |Multiplexer, Analog Dual 4-Bit | |Multiplexer, Analog Dual 4-Bit | |Multiplexer, Analog Dual 4-Bit | |Decoder, 3-to-8 Line | |Connector Flat 26 pins | |diode | |diode | |diode | |diode | |diode | |diode | |diode | |diode | |diode | |diode | |diode | |diode | |diode | |diode | |inductor | |inductor | |inductor | |inductor | |inductor | |inductor | |inductor | |inductor | |inductor | |Pin Wire | |Pin Wire | |Pin Wire | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor

|J6| |J2| |J3| |J4| |J5| |C19| |C20| |C7| |C2| |C1| |C3| |C8| |C4| |C5| |C6| |U12| |U13| |U16| |U11| |U14| |U15| |U17| |J1| |D14| |D7| |D9| |D8| |D2| |D3| |D10| |D11| |D1| |D4| |D12| |D5| |D13| |D6| |L7| |L6| |L9| |L2| |L1| |L3| |L4| |L5| |L8| |W5| |W6| |W7| |RT1| |RT2| |RT3|COD |RT4|COD |RT5|COD |R44| |R49| |R39| |R31| |R30| |R28| |R46| |R35| |R34| |R37| |R36| |R29| |R38| |R40| |R41| |R50| |R85| |R86| |R83| |R84| |R81| |R82| |R47|COD |R43|COD |R18|COD |R48|COD |R32|COD |R16|COD

Pag. 71

TX50S manual
83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |R1206-F-2K22 |R1206-F-5K23 |R1206-F-5K23 |R1206-F-5K23 |R1206-F-5K62 |R1206-F-8K45 |R1206-F-8K45 |R1206-F-8K45 |R1206-F-10K5 |R1206-F-10K5 |R1206-F-10K5 |R1206-F-10K7 |R1206-F-10K7 |R1206-F-10K7 |R1206-F-22K1 |R1206-F-22K1 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K2 |R1206-J-4K7 |R1206-J-4K7 |R1206-J-5K6 |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-10K |R1206-J-11K |R1206-J-11K |R1206-J-22K |R1206-J-22K |R1206-J-47R |R1206-J-47R |R1206-J-100K |R1206-J-120R |R1206-J-120R |R1206-J-120R |R1206-J-120R |R1206-J-120R |R1206-J-120R |R1206-J-120R |R1206-J-680R |R1206-J-680R |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TL072D |TL072D |TL072D |TL072D |TL072D |TL072D |TL072D |TL072D |TL072D |TL072D |TL072D |ZMM5V6 |Z2_P100 |Z2_P100 |Z2_P100 |Z2_P100 |Z2_P100 |Z2_P100 |Z2_P100 |Z2_P100 |c1206-100n |2K22 |5K23 |5K23 |5K23 |5K62 |8K45 |8K45 |8K45 |10K5 |10K5 |10K5 |10K7 |10K7 |10K7 |22K1 |22K1 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K2 |4K7 |4K7 |120 |10K |10K |10K |10K |10K |10K |10K |22K |10K |22K |22K |22K |22K |11K |11K |22K |22K |47R |47R |100K |120R |120R |120R |120R |120R |120R |120R |680R |680R |10u |10u |10u |10u |10u |10u |10u |10u |10u |10u | | | | | | | | | | | | | | | | | | | | |100n |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% | | | | | | | | | | | | | | | | | | | | |10% | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V | | | | | | | | | | | | | | | | | | | | |25V |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor | | | | | | | | | | |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |zener diode | | | | | | | | |capacitor |R17|COD |R25|COD |R27|COD |R26|COD |R87|COD |R22|COD |R24|COD |R23|COD |R21|COD |R19|COD |R20|COD |R45|COD |R33|COD |R42|COD |R80| |R79| |R56| |R57| |R55| |R58| |R54| |R53| |R51| |R52| |R76|COD |R77|COD |R70| |R62| |R61| |R78| |R4| |R5| |R3| |R6| |R15| |R7| |R8| |R9| |R10| |R11| |R12| |R13| |R14| |R72| |R73| |R75| |R74| |R60| |R59| |R71| |R64| |R67| |R65| |R69| |R63| |R66| |R68| |R1| |R2| |C17| |C10| |C18| |C11| |C12| |C13| |C14| |C15| |C16| |C9| |U1| |U2| |U18| |U3| |U6| |U7| |U5| |U4| |U8| |U9| |U10| |DZ1| |Z1| |Z7| |Z2| |Z6| |Z5| |Z4| |Z3| |Z8| |CF9A|

Pag. 72

TX50S manual
173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-220p |c1206-220p |c1206-220p |c1206-220p |c1206-270p |c1206-270p |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |220p |220p |220p |220p |270p |270p |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |100V |100V |100V |100V |100V |100V |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |CF11A| |CF13A| |CF15A| |CF8A| |CF10A| |CF12A| |CF14A| |CF16A| |CF17A| |CF8B| |CF9B| |CF10B| |CF11B| |CF12B| |CF13B| |CF14B| |CF15B| |CF16B| |CF2A| |CF18A| |CF1A| |CF3A| |CF7B| |CF6B| |CF5B| |CF4B| |CF6A| |CF4A| |CF7A| |CF5A| |CF1B| |CF2B| |CF3B| |CF18B| |C25| |C23| |C26| |C24| |C22| |C21|

Pag. 73

TX50S manual

DLCD BOARD - DISPLAY DRIVER

Pag. 74

TX50S manual

DLCD BOARD- DISPLAY DRIVER

Pag. 75

TX50S manual

DLCD BOARD - DISPLAY DRIVER

item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 |qty |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |part number |AM29F010N |BAR10 |BAY21 |BAY21 |BC183 |BC183 |BC183 |BERG100M1X02V |CCM_1n |CCM_1u |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_10n |CCM_10n |CCM_10n |CCM_10n |CCM_10n |CCM_10n |CCM_10n |CCM_10n |CCM_27p |CCM_27p |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CEH_220u-16V |CEV_10u-25 |CEV_10u-25 |CEV_10u-25 |CEV_10u-25 |DS1302N |JFL_26M |JFL_26M |KEYBELCA1 |LF353N |LF353N |LF353N |LM336_5V |LM358N |LM7805 |L025_22u |MAX232N |MC68HC11K1 |Val | | | | | | | | |1n |1u |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |10n |10n |10n |10n |10n |10n |10n |10n |27p |27p |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |220uF |uF |10u |10u |10u | | | | | | | |5V | | | | | |Tol | | | | | | | | |5% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |10% |10% |10% |10% |10% |10% |10% |10% |5% |5% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |20% |20% |20% |20% |20% | | | | | | | | | | | | | |Work.Volt.|description | | | |diode | |diode | |diode | |Transistor, NPN BJT | |Transistor, NPN BJT | |Transistor, NPN BJT | | |100V |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor |16V | |V | |25v | |25V | |25V | | |Real Time Clock | |Connector Flat 26 pins | |Connector Flat 26 pins | | | |Opamp 5-pin | |Opamp 5-pin | |Opamp 5-pin | |Voltage Reference, ADJ. | |Opamp 5-pin | |Voltage Regulator, FIXED | |inductor | |Driver-Receiver RS232 | |

|U2| |D6| |D4| |D5| |Q5| |Q6| |Q4| |J3| |C40|COD |C15|COD |C1|COD |C12|COD |C13|COD |C14|COD |C20|COD |CF1|COD |C31|COD |C32|COD |C33|COD |C37|COD |C38|COD |C39|COD |C27|COD |C14A|COD |C32A|COD |C32C|COD |C32B|COD |C2|COD |C3|COD |C4|COD |C5|COD |C6|COD |C7|COD |C8|COD |C9|COD |C10|COD |C11|COD |C16|COD |C17|COD |C18|COD |CF3|COD |CF4|COD |C22|COD |C23|COD |C24|COD |C26|COD |C25|COD |CF19|COD |CF21|COD |C28|COD |CF2|COD |CF5|C |CF6|COD |CF8|COD |CF9|COD |CF22|COD |C34|COD |C35|COD |C36|COD |CF20|COD |CF10|COD |C41|COD |C19| |C21| |C29| |C30| |U21| |J1| |J2| |U24| |U7| |U11| |U13| |U17| |U16| |U23| |L1| |U18| |U1|

Pag. 76

TX50S manual
80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |MC34064 |M40247JY |NE5532N |NE5532N |NE5532N |PBATT_D16 |REED1A_12V |REED1A_12V |REED1A_12V |REED1A_12V |RSIP8C_10K |R025-J-1K0 |R025-J-1K0 |R025-J-1K0 |R025-J-1K8 |R025-J-1K8 |R025-J-1R8 |R025-J-2M2 |R025-J-3K3 |R025-J-4K7 |R025-J-4K7 |R025-J-4K7 |R025-J-5K6 |R025-J-5K6 |R025-J-10K |R025-J-10K |R025-J-10K |R025-J-10K |R025-J-10K |R025-J-10K |R025-J-10K |R025-J-10K |R025-J-10K |R025-J-10K |R025-J-10K |R025-J-10M |R025-J-12K |R025-J-12K |R025-J-18K |R025-J-18K |R025-J-18K |R025-J-33K |R025-J-33K |R025-J-33K |R025-J-47K |R025-J-47K |R025-J-56K |R025-J-68K |R025-J-68K |R025-J-68K |R025-J-68K |R025-J-82R |R025-J-100K |R025-J-100R |R025-J-100R |R025-J-100R |R025-J-100R |R025-J-100R |R025-J-100R |R025-J-100R |R025-J-100R |R025-J-150K |R025-J-150K |R025-J-150K |R025-J-150K |R025-J-150K |R025-J-150K |R025-J-150K |R025-J-220R |R025-J-220R |R025-J-330R |R025-J-390K |R025-J-560R |R025-J-560R |R025-J-680R |R025-J-820R |SN75176N |SP_TM114 |VP0610L |VP0610L |VP0610L |XT-HC49U |XT-TC38 |ZPD5V6 |ZPD5V6 |ZPD5V6 |ZPD5V6 |ZPD5V6 |ZPD5V6 |ZPD5V6 | | | | | | | | | | |10K |1K0 |1K0 |1K0 |1K8 |1K8 |1R8 |2M2 |3K3 |4K7 |4K7 |4K7 |5K6 |5K6 |10K |10K |10K |10K |10K |10K |10K |10K |10K |10K |10K |10M |12K |12K |18K |18K |18K |33K |33K |33K |47K |47K |56K |68K |68K |68K |68K |82R |100K |100 |100 |100 |100 |100 |100 |100 |100 |150K |150K |150K |150K |150K |150K |150K |220R |220R |330R |390K |560R |560R |680R |820R | | | | | |MHz | | | | | | | | | | | | | | | | | | |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Battery |BOBINA RELE |RELAIS SPDT |RELAIS SPDT |BOBINA RELE | |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |Driver-Receiver R85 | |Mosfet, N-chan Power |Mosfet, N-chan Power |Mosfet, N-chan Power |Crystal |Crystal TC38 |zener diode |zener diode |zener diode |zener diode |zener diode |zener diode |zener diode |U22| |LCD1| |U12| |U14| |U15| |BT1| |RL2| |RL2| |RL1| |RL1| |RR1|COD |R46|COD |R47|COD |R49|COD |R54|COD |R45|COD |R55| |R21|COD |R50|COD |R2|COD |R3|COD |R33|COD |R34|COD |R35|COD |R6|COD |R8|COD |R10|COD |R12|COD |R14|COD |R16|COD |R18|COD |R20|C |R29|COD |R56|COD |R64|COD |R65|COD |R31|COD |R38|COD |R1|COD |R22|COD |R63|COD |R32|COD |R40|COD |R41|COD |R42|COD |R44|COD |R43|COD |R28|COD |R30|COD |R37|COD |R39|COD |R4|COD |R53|COD |R5|COD |R7|COD |R9|COD |R11|COD |R13|COD |R15|COD |R17|COD |R19|COD |R23|COD |R25|COD |R26|COD |R27|COD |R58|COD |R60|C |R61|COD |R51|COD |R52|COD |R59|COD |R62|COD |R24|COD |R57|COD |R48|COD |R36|COD |U19| |P9| |Q2| |Q3| |Q1| |XT1| |XT2| |DZ2| |DZ3| |DZ4| |DZ5| |DZ6| |DZ7| |DZ8|

Pag. 77

TX50S manual
170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |ZPD5V6 |Z3_P100 |Z3_P100 |1N4148 |1N4148 |1N4148 |74HC00N |74HC00N |74HC151N |74HC151N |74HC164N |74HC245N |74HC245N |74HC533N |74HC533N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |zener diode | | |diode |diode |diode |Gate, 2-Input NAND |Gate, 2-Input NAND |Mux, 8-Bit |Mux, 8-Bit |Shift Register, 8-Bit |Transceiver, Octal 3-State |Transceiver, Octal 3-State |Latch, Octal D-Type 3-S |Latch, Octal D-Type 3-S |DZ1| |Z1| |Z2| |D1| |D2| |D3| |U10| |U20| |U9| |U25| |U8| |U5| |U6| |U3| |U4|

Pag. 78

TX50S manual

MBA BOARD - MOTHER BOARD

Pag. 79

TX50S manual

MBA BOARD- MOTHER BOARD

Pag. 80

TX50S manual

MBA BOARD - MOTHER BOARD

Pag. 81

TX50S manual

MBA BOARD - MOTHER BOARD

Pag. 82

TX50S manual

MBA BOARD - MOTHER BOARD

item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 |qty |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |part number |BAR10 |BAR10 |BAR10 |BAR10 |BAY21 |BAY21 |BC183 |BERG100M1X02V |BERG100M1X03V |BERG100M1X08V |BERG100M1X08V |BERG100M1X12V |BERG100M1X14V |CCM_1n |CCM_1u |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_2u2 |CCM_68p |CCM_68p |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_100n |CCM_150p |CCM_150p |CCM_150p |CCM_150p |CCM_150p |CCM_150p |CCM_150p |CCM_150p |CCM_470p |CCM_470p |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_10u-25V |CEV_47u-25V |CPVST_1n2_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPVST_6n8_63V |CPV_10n_100V |Val | | | | | | | | | | | | | |1n |1u |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |2u2 |68p |68p |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |150p |150p |150p |150p |150p |150p |150p |150p |470p |470p |10u |10u |10u |10u |10u |10u |10u |10u |10u |10u |10u |10u |10u |47u |1n2 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |6n8 |10n |Tol | | | | | | | | | | | | | |5% |20% |20% |20% |20% |20% |20% |20% |20% |5% |5% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |20% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |Work.Volt.|description | |diode | |diode | |diode | |diode | |diode | |diode | |Transistor, NPN BJT | |Physical Connector | |Physical Connector | | | | | | | | |100V |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor |25V | |25V | |25V | |25V | |25V | |25V | |25V | |25V | |25V | |25V | |25V | |25V | |25V | |25V | |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |63V |capacitor |100V |capacitor |D5| |D2| |D4| |D3| |D6| |D7| |Q1| |J4| |J3| |J9| |J10| |J12| |J8| |C58| |C59| |C44| |C45| |C46| |C48| |C43| |C47| |C72| |C23| |C24| |C53| |C55| |C51| |C52| |C54| |C68| |C69| |C70| |C71| |C63| |C62| |C60| |C64| |C65| |C66| |C67| |C61| |CF23|COD |C17| |C19| |C18| |C20| |C21| |C22| |C16| |C15| |C56| |C57| |C1| |C2| |C10| |C9| |C3| |C4| |C5| |C12| |C7| |C11| |C6| |C13| |C8| |C73|COD |C26| |C38| |C31| |C42| |C32| |C36| |C33| |C40| |C39| |C34| |C29| |C35| |C37| |C30| |C41| |C28|COD |C27|COD |C49|

Pag. 83

TX50S manual
85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |CPV_10n_100V |CPV_470p_100V |C4051BN |C4051BN |JFL_26M |JFL_26M |JFL_26M |JFL_26M |J156X10 |J156X14 |LM358N |LM393N |LM7805 |LM7808 |LTUBE-D8P5 |LTUBE-D8P5 |LTUBE-D8P5 |LTUBE-D8P5 |L0305_10u |REED1A-HS-12V |REED1A-HS-12V |RT_67W |RT_67W |RT_67W |RT_67W |RT_67W |RT_67W |RT_67W |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K0 |R025-F-1K8 |R025-F-1K8 |R025-F-1K07 |R025-F-1K07 |R025-F-1K24 |R025-F-1K24 |R025-F-1K50 |R025-F-1K54 |R025-F-1K54 |R025-F-1K87 |R025-F-1K87 |R025-F-2K1 |R025-F-2K1 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |R025-F-2K2 |10n |470p | | | | | | | | | | | | |1mH |1mH |uH |uH |10uH | | |2K2 |0K |500 |2K2 |10K |10K |5K |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K0 |1K8 |1K8 |1K07 |1K07 |1K24 |1K24 |1K50 |1K54 |1K54 |1K87 |1K87 |2K1 |2K1 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |2K2 |10% |10% | | | | | | | | | | | | | | | | |10% | | |10% |10% |10% |10% |10% |10% |10% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |100V |100V | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |capacitor |capacitor |Multiplexer, Analog 8-Bit |Multiplexer, Analog 8-Bit |Connector Flat 26 pins |Connector Flat 26 pins |Connector Flat 26 pins |Connector Flat 26 pins | | |Opamp 5-pin |Voltage Comparator |Voltage Regulator, FIXED |Voltage Regulator, FIXED |inductor |inductor |inductor |inductor |inductor |BOBINA RELE |RELAIS SPDT |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |C50| |C25|COD |U17| |U18| |J1| |J2| |J7| |J11| |J6| |J5| |U21| |U22| |U20| |U19| |L1| |L2| |L4| |L3| |L5| |K1| |K1| |RT7| |RT2| |RT3| |RT1| |RT6| |RT5| |RT4| |R21| |R23| |R22| |R8| |R9| |R17| |R10| |R14| |R11| |R15| |R12| |R18| |R13| |R1| |R2| |R16| |R24| |R25| |R6| |R7| |R77| |R78| |R71| |R72| |R75| |R76| |R107|COD |R55| |R56| |R69| |R70| |R57| |R58| |R43| |R42| |R41| |R47| |R45| |R44| |R29| |R30| |R31| |R32| |R33| |R35| |R34| |R36| |R38| |R48| |R37| |R46| |R39| |R40| |R102| |R101| |R103| |R104| |R3| |R105| |R5| |R19| |R20|

Pag. 84

TX50S manual
175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |R025-F-2M2 |R025-F-3K9 |R025-F-3K30 |R025-F-5K6 |R025-F-5K6 |R025-F-6K81 |R025-F-8K2 |R025-F-8K25 |R025-F-10K |R025-F-10K |R025-F-10K |R025-F-10K |R025-F-10K0 |R025-F-10K0 |R025-F-10K0 |R025-F-15K |R025-F-18K |R025-F-18K0 |R025-F-18K0 |R025-F-18K0 |R025-F-27K0 |R025-F-33K |R025-F-33K |R025-F-33K0 |R025-F-33K0 |R025-F-47R |R025-F-95K3 |R025-F-95K3 |R025-F-100K |R025-F-100K |R025-F-100K |R025-F-100K |R025-F-100K |R025-F-100R |R025-F-100R |R025-F-100R |R025-F-100R |R025-F-120R |R025-F-120R |R025-F-120R |R025-F-150R |R025-F-243R |R025-F-243R |R025-F-330R |R025-F-330R |R025-F-390R |R025-F-390R |R025-F-500R |R025-F-562R |R025-F-562R |R025-F-680R |R025-F-768R |R025-F-768R |R025-F-822R |R025-F-825R |R025-F-825R |R025-F-825R |R025-F-825R |TIP127 |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |TL072N |VP0610L |VP0610L |ZPD8V2 |ZPD12V |Z3-100 |Z3-100 |Z3_P100 |1N4148 |74HC00N |2M2 |3K9 |3K30 |5K6 |5K6 |6K81 |8K2 |8K25 |10K |10K |10K |10K |10K0 |10K0 |10K0 |15K |18K |18K0 |18K0 |18K0 |27K4 |33K |33K |33K0 |33K0 |47R |95K3 |95K3 |100K |100K |100K |100K |100K |100R |100R |100R |100R |120R |120R |120R |150R |243R |243R |330R |330R |390R |390R |500R |562R |562R |680R |768R |768R |822R |825R |825R |825R |825R | | | | | | | | | | | | | | | | | | | | | | | | | | |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |Transistor, PNP Darlington |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Mosfet, N-chan Power |Mosfet, N-chan Power |zener diode |zener diode | | | |diode |Gate, 2-Input NAND |R94| |R95| |R111|COD |R96| |R97| |R4|COD |R100| |R82|COD |R85| |R84| |R83| |R81| |R113|COD |R114|COD |R115|COD |R89| |R99| |R120|COD |R119|COD |R110|COD |R98|COD |R93| |R92| |R109|COD |R112|COD |R91| |R53| |R54| |R73| |R74| |R117|COD |R116|COD |R118|COD |R51| |R52| |R49| |R50| |R26| |R27| |R28| |R108|COD |R59| |R60| |R87| |R88| |R79| |R80| |R86| |R61| |R62| |R90| |R63| |R64| |R106|COD |R65| |R66| |R68| |R67| |Q2| |U1| |U2| |U3| |U4| |U5| |U6| |U7| |U8| |U9| |U10| |U11| |U12| |U13| |U15| |U14| |U16| |Q4| |Q3| |DZ2|COD |DZ1|COD |Z1| |Z2| |Z3| |D1| |U23|

Pag. 85

TX50S manual

KEY BOARD - KEY

Pag. 86

TX50S manual

KEY BOARD - KEY

Pag. 87

TX50S manual

KEY BOARD - KEY

item 1 2 3 4 5 6 7 8 9 10 11 12 13 |qty |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |part number |BERG100M2X07V |LED_D3V |LED_D3V |RSIP8C_10K |SP_3FT |SP_3FT |SP_3FT |SP_3FT |SP_3FT |SP_3FT |SP_3FT |SP_3FTL |SP_3FTL |Val | | | |10K | | | | | | | | | |Tol | | | |5% | | | | | | | | | |Work.Volt.|description | |Physical Connector | |photoemissive diode | |photoemissive diode | | | | | | | | | | | | | | | | | | | |photoemissive diode |J1| |DL3| |DL2| |RR1| |P1| |P2| |P3| |P4| |P5| |P6| |P8| |P7DL1| |P7DL1|

Pag. 88

TX50S manual

SINTD BOARD- VCO OSCILLATOR

Pag. 89

TX50S manual

SINTD BOARD - VCO OSCILLATOR

Pag. 90

TX50S manual

SINTD BOARD - VCO OSCILLATOR

item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 |qty |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |part number |BCW31 |BCW72 |BERG100M1X14V |BFR92 |BFR92 |BFR92 |CEV_100u-35V |CEV_100u-35V |CEV_100u-35V |CEV_100u-35V |CEV_100u-35V |Coax |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C1210 |C4016BD |DROP |HSS2800 |HSS2800 |HSS2800 |LF353D |LL4148 |LL4148 |LL4148 |LL4148 |LMX2306D |LM358D |LM358D |L1812_1mH |L1812_2u2H |L1812_6u8H |MAV1_2-16_DIA300 |MAV11 |MAV11 |MMBFJ310LT1 |MMBR571LT1 |MMBV109LT1 |MMBV109LT1 |MMBV109LT1 |MMBV109LT1 |MMBV109LT1 |MMBV109LT1 |MMBV109LT1 |MMBV109LT1 |MMBV109LT1 |RCH_895 |RT_3314J |R1206-F-42K0 |R1206-J-1K0 |R1206-J-1K0 |Val | | | | | | |100u |100u |100u |100u |100u | |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n |1n | | | | | | | | | | | | | |1mH |2u2H |6u8H |1.6-16 pF | | | | |26-32 pF |26-32 pF |26-32 pF |26-32 pF |26-32 pF |26-32 pF |26-32 pF |26-32 pF |26-32 pF |uH |500 |42K0 |1K0 |1K0 |Tol | | | | | | |20% |20% |20% |20% |20% | |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 |20 | | | | | | | | | | | | | | | | |% | | | | | | | | | | | | | | |10% |1% |5% |5% |Work.Volt.|description | |Transistor, NPN BJT | |Transistor, NPN BJT | | | |Transistor, NPN BJT | |Transistor, NPN BJT | |Transistor, NPN BJT |35V | |35V | |35V | |35V | |35V | | | Coaxial Line | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |capacitor | |Analog Switch, Bilateral | | | |diode | |diode | |diode | |Opamp 5-pin | |diode | |diode | |diode | |diode | | | |Opamp 5-pin | |Opamp 5-pin | |inductor | |inductor | |inductor | |capacitor | | | | | |JFET, N-chan | |Transistor, NPN BJT | |Varactor | |Varactor | |Varactor | |Varactor | |Varactor | |Varactor | |Varactor | |Varactor | |Varactor | |inductor | |resistor | |resistor | |resistor | |resistor |Q2| |Q3| |J2| |Q7| |Q5| |Q4| |C19| |C16| |C15| |C17| |C21| |Coax1| |C38| |C26| |C27| |C34| |C28| |C35| |C39| |C40| |C29| |C41| |C24| |C36| |C31| |C42| |C25| |C32| |C30| |C55| |C56| |C57| |C2| |C51| |C33| |C58| |U13| |Z1| |D3| |D5| |D4| |U2| |D7| |D6| |D1| |D2| |U4| |U6| |U7| |L3| |L2| |L1| |CV1| |U3| |U14| |Q1| |Q6| |DV1| |DV2| |DV3| |DV4| |DV5| |DV6| |DV7| |DV8| |DV9| |L4| |RT1| |R30|COD |R3| |R5|

Pag. 91

TX50S manual
72 |1 |R1206-J-1K2 73 |1 |R1206-J-1M0 74 |1 |R1206-J-2K2 75 |1 |R1206-J-2K2 76 |1 |R1206-J-2K4 77 |1 |R1206-J-3K3 78 |1 |R1206-J-3K9 79 |1 |R1206-J-4K7 80 |1 |R1206-J-4K7 81 |1 |R1206-J-4K7 82 |1 |R1206-J-8K2 83 |1 |R1206-J-8K2 84 |1 |R1206-J-10K 85 |1 |R1206-J-10K 86 |1 |R1206-J-10K 87 |1 |R1206-J-10K 88 |1 |R1206-J-10K 89 |1 |R1206-J-10K 90 |1 |R1206-J-10K 91 |1 |R1206-J-10K 92 |1 |R1206-J-10K 93 |1 |R1206-J-12K 94 |1 |R1206-J-15K 95 |1 |R1206-J-18K 96 |1 |R1206-J-18K 97 |1 |R1206-J-22K 98 |1 |R1206-J-22K 99 |1 |R1206-J-22K 100 |1 |R1206-J-22K 101 |1 |R1206-J-33K 102 |1 |R1206-J-33K 103 |1 |R1206-J-56K 104 |1 |R1206-J-56R 105 |1 |R1206-J-56R 106 |1 |R1206-J-75R 107 |1 |R1206-J-82K 108 |1 |R1206-J-82K 109 |1 |R1206-J-82K 110 |1 |R1206-J-82R 111 |1 |R1206-J-100K 112 |1 |R1206-J-100K 113 |1 |R1206-J-100R 114 |1 |R1206-J-100R 115 |1 |R1206-J-150R 116 |1 |R1206-J-150R 117 |1 |R1206-J-200R 118 |1 |R1206-J-200R 119 |1 |R1206-J-200R 120 |1 |R1206-J-330R 121 |1 |R1206-J-330R 122 |1 |R1206-J-330R 123 |1 |R1206-J-330R 124 |1 |R1206-J-330R 125 |1 |R1206-J-330R 126 |1 |R1206-J-330R 127 |1 |R1206-J-330R 128 |1 |R1206-J-330R 129 |1 |R1206-J-360R 130 |1 |R1206-J-680R 131 |1 |R1210-J-68R 132 |1 |R1210-J-82R 133 |1 |R1210-J-82R 134 |1 |R1210-J-100R 135 |1 |R1210-J-100R 136 |1 |R1210-J-100R 137 |1 |R1210-J-100R 138 |1 |R2512 139 |1 |R2512 140 |1 |R2512 141 |1 |SMB-A 142 |1 |TAJ_10u-25V 143 |1 |TAJ_10u-25V 144 |1 |TAJ_10u-25V 145 |1 |TAJ_10u-25V |10u 146 |1 |TAJ_10u-25V 147 |1 |TAJ_10u-25V 148 |1 |TAJ_10u-25V 149 |1 |TAJ_10u-25V 150 |1 |TAJ_22u-16V 151 |1 |TAJ_22u-16V 152 |1 |TAJ_22u-16V 153 |1 |XTAL-BLOCK 154 |1 |ZMM3V3 155 |1 |ZMM3V3 156 |1 |c1206-22p 157 |1 |c1206-33p 158 |1 |c1206-33p 159 |1 |c1206-47n 160 |1 |c1206-68p 161 |1 |c1206-100n |1K2 |1M |2K2 |2K2 |2K4 |3K3 |3K9 |4K7 |4K7 |4K7 |8K2 |8K2 |10K |10K |10K |10K |10K |10K |10K |10K |10K |12K |15K |18K |18K |22K |22K |22K |22K |33K |33K |56K |56R |56R |75R |82K |82K |82K |82R |100K |100K |100R |100R |150R |150R |200R |200R |200R |330R |330R |330R |330R |330R |330R |330R |330R |330R |360R |680R |68R |82R |82R |100R |100R |100R |100R |33 |33 |33 | |10u |10u |10u |20% |25V |10u |10u |10u |10u |22u |22u |22u | | | |22p |33p |33p |47n |68p |100n |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% | |20% |20% |20% | |20% |20% |20% |20% |20% |20% |20% | | | |10% |10% |10% |10% |10% |10% | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |BNC |25V | |25V | |25V | |C12|COD |25V | |25V | |25V | |25V | |16V | |16V | |16V | | | | |zener diode | |zener diode |100V |capacitor |100V |capacitor |100V |capacitor |25V |capacitor |100V |capacitor |25V |capacitor |R13| |R67|COD |R48| |R49| |R58|COD |R4|COD |R1| |R10| |R11| |R9| |R36|COD |R17|COD |R31| |R37| |R28| |R29| |R33| |R27| |R35| |R34| |R64| |R54|COD |R59| |R14|COD |R32|COD |R57| |R56| |R55| |R66| |R12| |R65| |R60| |R46| |R45| |R41|COD |R8| |R6| |R7| |R47|COD |R15| |R16| |R40| |R42| |R51| |R50| |R38| |R39| |R44|COD |R23| |R25| |R24| |R26| |R18| |R19| |R20| |R21| |R22| |R2|COD |R52| |R69|COD |R53|COD |R71|COD |R43|COD |R70|COD |R72|COD |R68|COD |R62| |R63| |R61| |J1| |C18|COD |C4|COD |C11|COD |C13|COD |C1|COD |C14|COD |C37|COD |C20|COD |C53|COD |C54|COD |U5| |DZ1| |DZ2| |C46|COD |C45| |C50|COD |C47| |C44| |C8|

Pag. 92

TX50S manual
162 163 164 165 166 167 168 169 170 171 172 173 174 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-150p |c1206-150p |c1206-220n |c1206-470n |c1206-470n |74HC08D |100n |100n |100n |100n |100n |100n |100n |150p |150p |220n |470n |470n | |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% | |25V |25V |25V |25V |25V |25V |25V |100V |100V |15V |15V |15V | |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |Gate, 2-Input AND |C6| |C10| |C7| |C5| |C9| |C3| |C52|COD |C49| |C48| |C23| |C22| |C43|COD |U1|

Pag. 93

TX50S manual

DMPX BOARD - STEREOCODER

Pag. 94

TX50S manual

DMPX BOARD - STEREOCODER

Pag. 95

TX50S manual

DMPX BOARD - STEREOCODER

item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 |qty |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |part number |BERG100M1X08V |BERG100M1X08V |C4011BD |C4011BD |C4011BD |C4011BD |C4013BD |C4013BD |C4017BD |C4017BD |C4029BD |C4029BD |C4040BD |C4051BD |C4051BD |C4051BD |C4051BD |C4051BD |C4051BD |LL4148 |LL4148 |RT_3314J |RT_3314J |RT_3314J |R1206-F-1K0 |R1206-F-1K3 |R1206-F-1K8 |R1206-F-2K2 |R1206-F-2K2 |R1206-F-2K2 |R1206-F-2K2 |R1206-F-2K2 |R1206-F-2K7 |R1206-F-2K7 |R1206-F-2M2 |R1206-F-8K2 |R1206-F-8K2 |R1206-F-10K |R1206-F-10K |R1206-F-10K |R1206-F-10K |R1206-F-10K |R1206-F-51R |R1206-F-68R |R1206-F-68R |R1206-F-68R |R1206-F-68R1 |R1206-F-100K |R1206-F-100R |R1206-F-100R |R1206-F-100R |R1206-F-100R |R1206-F-100R |R1206-F-100R |R1206-F-100R |R1206-F-100R |R1206-F-162R |R1206-F-162R |R1206-F-180R |R1206-F-200R |R1206-F-324R |R1206-F-432R |R1206-F-453R |R1206-F-453R |R1206-F-500R |R1206-F-536R |R1206-F-604R |R1206-F-649R |R1206-F-681R |R1206-F-681R |R1206-F-681R |R1206-F-806R |Val | | | | | | | | | | | | | | | | | | | | | |1K |100 |10K |1K0 |1K3 |1K8 |2K2 |2K2 |2K2 |2K2 |2K2 |2K7 |2K7 |2M2 |8K2 |8K2 |10K |10K |10K |10K |10K |51R |68R |68R |68R |68R1 |100K |100R |100R |100R |100R |100R |100R |100R |100R |162R |162R |180R |200R |324R |432R |453R |453R |500R |536R |620K |649R |681R |681R |681R |806R |Tol | | | | | | | | | | | | | | | | | | | | | |10% |10% |10% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |Work.Volt.|description | | | | | |Gate, 2-Input NAND | |Gate, 2-Input NAND | |Gate, 2-Input NAND | |Gate, 2-Input NAND | |Flip-Flop, D-Type | |Flip-Flop, D-Type | |Counter/Divider, Decade | |Counter/Divider, Decade | | | | | |Counter, 12-Stage | |Multiplexer, Analog 8-Bit | |Multiplexer, Analog 8-Bit | |Multiplexer, Analog 8-Bit | |Multiplexer, Analog 8-Bit | |Multiplexer, Analog 8-Bit | |Multiplexer, Analog 8-Bit | |diode | |diode | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor

|J1| |J2| |U1| |U21| |U7| |U12| |U8| |U13| |U6| |U11| |U23| |U5| |U2| |U3| |U4| |U9| |U10| |U15| |U20| |D1| |D2| |RT1| |RT3| |RT2| |R43| |R47| |R34| |R27| |R28| |R39| |R33| |R31| |R40| |R10| |R46| |R23| |R49| |R41| |R50| |R22| |R48| |R42| |R30| |R36| |R37| |R21| |R2| |R32| |R20| |R45| |R44| |R26| |R29| |R24| |R35| |R38| |R19| |R12| |R1| |R3| |R4| |R5| |R18| |R13| |R25| |R6| |R7| |R8| |R9| |R17| |R14| |R16|

Pag. 96

TX50S manual
73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |R1206-F-806R |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TAJ_10u-25V |TL072D |TL072D |TL072D |TL072D |TZBX4 |XT-HC49U |c1206-10p |c1206-10p |c1206-22p |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100p |c1206-100p |c1206-100p |c1206-100p |c1206-150p |c1206-150p |c1206-150p |c1206-150p |c1206-150p |c1206-150p |806R |10u |10u |10u |10u |10u |10u |10u |10u | | | | |22p |MHz |10p |10p |22p |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100p |100p |100p |100p |150p |150p |150p |150p |150p |150p |1% |20% |20% |20% |20% |20% |20% |20% |20% | | | | |5% | |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% | |25V |25V |25V |25V |25V |25V |25V |25V | | | | | | |100V |100V |100V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |100V |100V |100V |100V |100V |100V |100V |100V |100V |100V |resistor | | | | | | | | |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin |capacitor |Crystal |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |R15| |C4| |C8| |C14| |C17| |C20| |C21| |C9| |C7| |U14| |U16| |U19| |U22| |C22| |XT1| |C3| |C18| |C2| |CF2| |CF2A| |CF1A| |CF1| |CF6| |CF6A| |CF11| |CF11A| |CF23| |CF23A| |CF10| |CF10A| |CF9| |CF9A| |CF8| |CF8A| |CF5| |CF5A| |CF4| |CF4A| |CF3| |CF3A| |CF7| |CF7A| |CF20| |CF20A| |CF21| |CF21A| |CF13| |CF13A| |CF12| |CF12A| |CF15A| |CF15| |C1| |C15| |C5| |C19| |C16| |C26| |C25| |C6| |C24| |C23|

Pag. 97

TX50S manual

AGC BOARD- AUDIO AUTOMATIC GAIN CONTROL

Pag. 98

TX50S manual

AGC BOARD - AUDIO AUTOMATIC GAIN CONTROL

Pag. 99

TX50S manual

AGC BOARD - AUDIO AUTOMATIC GAIN CONTROL

item |qty |part number |references|Magazzino 1 |1 |BERG100M1X12V 2 |1 |C4051BD 3 |1 |C4051BD 4 |1 |C4051BD 5 |1 |C4051BD 6 |1 |LL4148 7 |1 |LL4148 8 |1 |LL4148 9 |1 |LL4148 10 |1 |L1812_6u8H 11 |1 |RT_3314J-10K 12 |1 |R1206-F-5K11 13 |1 |R1206-F-5K23 14 |1 |R1206-F-5K49 15 |1 |R1206-F-5K76 16 |1 |R1206-F-5K90 17 |1 |R1206-F-6K19 18 |1 |R1206-F-6K49 19 |1 |R1206-F-6K81 20 |1 |R1206-F-7K15 21 |1 |R1206-F-7K50 22 |1 |R1206-F-7K87 23 |1 |R1206-F-8K06 24 |1 |R1206-F-8K45 25 |1 |R1206-F-8K87 26 |1 |R1206-F-9K31 27 |1 |R1206-F-9K76 28 |1 |R1206-F-10K0 29 |1 |R1206-F-10K2 30 |1 |R1206-F-10K5 31 |1 |R1206-F-11K0 32 |1 |R1206-F-11K5 33 |1 |R1206-F-12K1 34 |1 |R1206-F-12K7 35 |1 |R1206-F-13K3 36 |1 |R1206-F-14K0 37 |1 |R1206-F-14K7 38 |1 |R1206-F-15K8 39 |1 |R1206-F-16K4 40 |1 |R1206-F-16K5 41 |1 |R1206-F-17K4 42 |1 |R1206-F-18K2 43 |1 |R1206-F-19K1 44 |1 |R1206-F-20K0 45 |1 |R1206-J-1K0 46 |1 |R1206-J-1M0 47 |1 |R1206-J-2K2 48 |1 |R1206-J-2K2 49 |1 |R1206-J-2K2 50 |1 |R1206-J-3K9 51 |1 |R1206-J-5K6 52 |1 |R1206-J-5K6 53 |1 |R1206-J-10K 54 |1 |R1206-J-10K 55 |1 |R1206-J-18K 56 |1 |R1206-J-22K 57 |1 |R1206-J-27K 58 |1 |R1206-J-47R 59 |1 |R1206-J-56K 60 |1 |R1206-J-56K 61 |1 |R1206-J-270R 62 |1 |R1206-J-270R 63 |1 |R1206-J-330R 64 |1 |ST62E25M1 65 |1 |TAJ_10u-25V 66 |1 |TAJ_10u-25V 67 |1 |TL072D 68 |1 |TL072D 69 |1 |TL072D |Val | | | | | | | | | |6,8uH |10K |5K11 |5K23 |5K49 |5K76 |5K90 |6K19 |6K49 |6K81 |7K15 |7K50 |7K87 |8K06 |8K45 |8K87 |9K31 |9K76 |10K0 |10K2 |10K5 |11K0 |11K5 |12K1 |12K7 |13K3 |14K |14K7 |15K8 |16K4 |16K5 |17K4 |18K2 |19K1 |20K0 |1K0 |1M |2K2 |2K2 |2K2 |3K9 |5K6 |5K6 |10K |10K |18K |22K |27K |47R |56K |56K |270R |270R |330R | |10u |10u | | | |Tol | | | | | | | | | |10 |10% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% |5% | |20% |20% | | | |Work.Volt.|description | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |25V |25V | | | | |Multiplexer, |Multiplexer, |Multiplexer, |Multiplexer, |diode |diode |diode |diode |inductor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor |resistor | | | |Opamp 5-pin |Opamp 5-pin |Opamp 5-pin Analog Analog Analog Analog 8-Bit 8-Bit 8-Bit 8-Bit |J1| |U2| |U3| |U4| |U5| |D2| |D1| |D4| |D3| |L1| |RT1|COD |R33|COD |R32|COD |R31|COD |R30|COD |R29|COD |R28|COD |R27|COD |R26|COD |R25|COD |R24|COD |R23|COD |R22|COD |R21|COD |R20|COD |R19|COD |R18|COD |R52|COD |R17|COD |R16|COD |R15|COD |R14|COD |R13|COD |R12|COD |R11|COD |R10|COD |R9|COD |R7|COD |R8|COD |R6|COD |R5|COD |R4|COD |R3|COD |R2|COD |R39|COD |R45|COD |R35|COD |R37|COD |R38|COD |R44|COD |R43|COD |R50|COD |R36|COD |R48|COD |R1|COD |R51|COD |R46|COD |R41|COD |R42|COD |R49|COD |R34|COD |R40|COD |R47|COD |U1| |CF6|COD |CF6A|COD |U6| |U7| |U8|

Pag. 100

TX50S manual
70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |TL072D |XT-HC49U |XT-KX20 |ZMM5V6 |Z3_P100 |c1206-33p |c1206-33p |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-100n |c1206-470n |c1206-470n | |MHz |MHz | | |33p |33p |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |100n |470n |470n | | | | | |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% |10% | | | | | |100V |100V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |25V |15V |15V |Opamp 5-pin |Crystal |Crystal |zener diode | |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |capacitor |U9| |XT1A| |XT1| |DZ1|COD |Z1| |C2|COD |C1|COD |CF2|COD |CF2A|COD |CF4|COD |CF5|COD |CF5A|COD |CF3|COD |CF3A|COD |C4|COD |CF7|COD |CF7A|COD |CF9A|COD |CF9|COD |CF8A|COD |CF8|COD |CF4A|COD |C3|COD |C5|COD

Pag. 101

TX50S manual

CON BOARD - MBA / RFDC CONNECTION

Pag. 102

TX50S manual

CON BOARD - MBA / RFDC CONNECTION

Pag. 103

TX50S manual

CON BOARD - MBA / RFDC CONNECTION

Item 1 2 3 4 5 6 7 8 9 10 11 |qty |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |part number |CCM_100n |CCM_100n |CCM_100n |J156X10 |PAD_160X140 |PAD_160X140 |PAD_160X140 |PAD_160X140 |PAD_160X140 |PAD_160X140 |TIP122 |Val |100n |100n |100n | | | | | | | | |Tol |10% |10% |10% | | | | | | | | |Work.Volt.|description | |capacitor | |capacitor | |capacitor | | | |Pin Wire | |Pin Wire | |Pin Wire | |Pin Wire | |Pin Wire | |Pin Wire | |Transistor, NPN Darlington

|C1| |C2| |C3| |J1| |W1| |W2| |W3| |W4| |W5| |W6| |Q1|

Pag. 104

TX50S manual

40WN BOARD - RF POWER MODULE

Pag. 105

TX50S manual

40WN BOARD- RF POWER MODULE

Pag. 106

TX50S manual

40WN BOARD - RF POWER MODULE

item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 |qty |1 |1 |16 |9 |1 |1 |1 |1 |2 |1 |1 |1 |1 |2 |1 |1 |1 |1 |1 |2 |4 |2 |1 |1 |1 |1 |1 |1 |2 |2 |14 |1 |1 |1 |1 |2 |1 |1 |4 |2 |1 |part number |BFQ68 |BFR96 |CSMD-HQ |C1210 |DU2860U |LCS_ELCA1 |LCS_ELCA2 |LCS_ELCA3 |LL4148 |L_VK200_P600 |L_2SP_5D_2L |L_2SP_5D_6L |L_2SP_7D_3L |L_4SP_7D_8L |L_6SP_8D_12L |L_6SP_8D_15L |L_6SP_8D_18L |L_8SP_8D_8L |L_20SP_6D_17L |L1812 |PAD_160X140 |RT_3314J |R1206-J-5K6 |R1206-J-10R |R1206-J-15R |R1206-J-56R |R1206-J-100R |R1206-J-270R |R1206-J-470R |R1206-J-680R |R2512 |SMB-A |TAJ_10u-25V |ZMM5V6 |c1206-33p |c1206-47p |c1206-56p |c1206-68p |c1206-100n |c1206-100p |c1206-150p |description |references |NPN 4 GHz Wideband Transistor |Q2 |NPN 4 GHz Wideband Transistor |Q1 |Chip High Frequency Monolithic Ceramic Capacitor|C11,C19,C21-C34 |Capacitor SMD 1210 |C1-C5,C14-C15,C17,C38 |N-Channel RF Power MOSFET (MaCom) |Q3 |BOBINA SU C.S. Ri=2.6mm, W=0.4mm, S=1mm, N=2.5 AVV.|L1 |BOBINA SU C.S. Ri=2.6mm, W=0.4mm, S=1mm, N=2.5 AVV.|L2 |BOBINA SU C.S. Ri=2.2mm, W=0.6mm, S=1mm, N=2.5 AVV.|L3 |diode |D1-D2 |Inductor PTH VK200 PASSO 600th |L14 |Bobina 2 Spire, diametro 5mm, larghezza 2mm, a Saldare|L4 |Bobina 2 Spire, diametro 5mm, larghezza 6mm, a Saldare|L5 |Bobina 2 Spire, diametro 7mm, larghezza 3mm, a Saldare|L7 |Bobina 4 Spire, diametro 7mm, larghezza 8mm, a Saldare|L8-L9 |Bobina 6 Spire, diametro 8mm, larghezza 12mm, a Saldare|L11 |Bobina 6 Spire, diametro 8mm, larghezza 15mm, a Saldare|L12 |Bobina 6 Spire, diametro 8mm, larghezza 18mm, a Saldare|L10 |Bobina 8 Spire, diametro 8mm, larghezza 8mm, a Saldare|L13 |Bobina 20 Spire, diametro 6mm, larghezza 17mm, a Saldare|L6 |Inductor SMD 1812 |L15-L16 |PAD X C.S. TIPO SMD 160X140 mills |J2-J5 |TRIMMER SMD 4 x 4.7 mm |RT1-RT2 |RESISTOR SMD 1206 |R4 |RESISTOR SMD 1206 |R9 |RESISTOR SMD 1206 |R6 |resistor |R1 |RESISTOR SMD 1206 |R5 |resistor |R2 |RESISTOR SMD 1206 |R7-R8 |RESISTOR SMD 1206 |R10,R24 |RESISTOR SMD 2512 |R3,R11-R23 |Female Right Angle SMB, PCB Mounting|J1 |TAJ Tantalium Capacitor SMD Size C|C13 |Zener Diode 0,5 W - 5.6 V |DZ1 |CAPACITOR SMD 1206 |C10 |CAPACITOR SMD 1206 |C6-C7 |CAPACITOR SMD 1206 |C8 |CAPACITOR SMD 1206 |C37 |CAPACITOR SMD 1206 |C12,C20,C35-C36 |CAPACITOR SMD 1206 |C9,C16 |CAPACITOR SMD 1206 |C18

Pag. 107

TX50S manual

RFDC BOARD - DIRECTIONAL COUPLER

Pag. 108

TX50S manual

RFDC BOARD - DIRECTIONAL COUPLER

Pag. 109

TX50S manual

RFDC BOARD - DIRECTIONAL COUPLER

item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 |qty |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |1 |part number |BNC-A |C1210 |C1210 |C1210 |C1210 |Elca_Coupler_RFDC |HSS2800 |HSS2800 |HSS2800 |HSS2800 |L1812 |L1812 |NE5532D |PAD_160X140 |PAD_160X140 |PAD_160X140 |PAD_160X140 |PAD_160X140 |RT_3314J |RT_3314J |RT_3314J |RT_3314J |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-1K0 |R1206-J-10K |R1206-J-10K |R1206-J-15R |R1206-J-15R |R1206-J-120R |R1206-J-120R |R1206-J-200R |R1206-J-200R |R1206-J-220K |R1206-J-220K |R1206-J-220K |R1206-J-220K |R1206-J-270R |R1206-J-270R |R1206-J-270R |R1206-J-270R |R1206-J-270R |R1206-J-270R |R1206-J-330R |R1206-J-330R |R1206-J-470R |R1206-J-470R |R2512 |R2512 |SMB-A |c1206-0p3 |c1206-1n |c1206-1n |c1206-22p |c1206-33p |c1206-33p |c1206-100n |c1206-100n |Val | |1n |1n |1n |1n | | | | | | | | | | | | | |2K2 |2K2 |2K2 |2K2 |1K |1K |1K |1K |10K |10K |15R |15R |120R |120R |200R |220R |220R |220K |220K |220K |270R |270R |270R |270R |270R |270R |330R |330R |470R |470R |82R |82R | |0p3 |1n |1n |22p |33p |33p |100n |100n |Tol | |10% |10% |10% |10% | | | | | | | | | | | | | | | | | |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% |1% | |10% |10% |10% |10% |10% |10% |10% |10% |Work.Volt.|description | |BNC | |capacitor | |capacitor | |capacitor | |capacitor | | | |diode | |diode | |diode | |diode | |inductor | |inductor | |Opamp 5-pin | |Physical Connector | |Physical Connector | |Physical Connector | |Physical Connector | |Physical Connector | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |resistor | |BNC |100V |capacitor |50V |capacitor |50V |capacitor |100V |capacitor |100V |capacitor |100V |capacitor |25V |capacitor |25V |capacitor

|J2| |C2| |C3| |C7| |C8| |TC1| |D1| |D2| |D3| |D4| |L1| |L2| |U1| |J6| |J7| |J4| |J5| |J1| |RT1| |RT2| |RT3| |RT4| |R12| |R11| |R22| |R21| |R29| |R24| |R3| |R6| |R8| |R18| |R16| |R26| |R20| |R19| |R9| |R10| |R15| |R14| |R13| |R28| |R27| |R25|COD |R7| |R17| |R1| |R4| |R2| |R5| |J3| |C12| |C5| |C9| |C11| |C1| |C6| |C4| |C10|

Pag. 110