Answer CCNA Security Chapter 2 Test - CCNAS v1.

1 | Invisible Algorithm

3/20/13 4:08 PM

Answer CCNA Security Chapter 2 Test CCNAS loading v1.1

In this post, i share the questions and answer for CCNA Security Chapter 2 Test. This CCNA Security Chapter 2 So i share the new questions and answer for your references.

test is using CCNAS v1.1. I took this CCNAS Chapter 2 Test on April 2012. Several new questions were included.

1. Refer to the exhibit. What two pieces of information can be gathered from the generated message? (Choose two. ) This message is a level five notification message. This message appeared because a minor error occurred requiring further investigation. This message appeared because a major error occurred requiring immediate action. This message indicates that service timestamps have been globally enabled. This message indicates that enhanced security was configured on the vty ports.

2. By default, how many seconds of delay between virtual login attempts is invoked when the login block-for command is configured? one two three four five

http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/

Page 1 of 12

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

3. Refer to the exhibit. Routers R1 and R2 are connected via a serial link. One router is configured as the NTP of the show ntp associations detail command on R2? (Choose two. ) Both routers are configured to use NTPv2. Router R1 is the master, and R2 is the client. Router R2 is the master, and R1 is the client. The IP address of R1 is 192. 168. 1. 2. The IP address of R2 is 192. 168. 1. 2. 4. What are two characteristics of the SDM Security Audit wizard? (Choose two. ) It uses interactive dialogs and prompts to implement AAA. router. configuration changes to implement. to the outside network. services are tested against known vulnerabilities.

master, and the other is an NTP client. Which two pieces of information can be obtained from the partial output

It automatically enables Cisco IOS firewall and implements Cisco IOS IPS security configurations to secure the

It displays a screen with Fix-it check boxes to let you choose which potential security-related

It requires users to first identify which router interfaces connect to the inside network and which connect

It is initiated from CLI and executes a script in which the managment plane functions and forwarding plane

5. If AAA is already enabled, which three CLI steps are required to configure a router with a specific view? (Choose three. ) assign a secret password to the view assign commands to the view assign users who can use the view associate the view with the root view create a superview using the parser view view-name command create a view using the parser viewview-name command

6. Refer to the exhibit. Which statement regarding the JR-Admin account is true? JR-Admin can issue show, ping, and reload commands. JR-Admin can issue ping and reload commands. JR-Admin can issue only ping commands. JR-Admin can issue debug and reload commands.
http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/ Page 2 of 12

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

JR-Admin cannot issue any command because the privilege level does not match one of those defined.

7. Which recommended security practice prevents attackers from performing password recovery on a Cisco IOS router for the purpose of gaining access to the privileged EXEC mode? Keep a secure copy of the router Cisco IOS image and router configuration file as a backup. Disable all unused ports and interfaces to reduce the number of ways that the router can be accessed. Configure secure administrative control to ensure that only authorized personnel can access the router. Locate the router in a secure locked room that is accessible only to authorized personnel. Provision the router with the maximum amount of memory possible. 8. Which three options can be configured by Cisco AutoSecure? (Choose three.) CBAC SNMP syslog security banner (Corrected by Andy) interface IP address enable secret password

9. Refer to the exhibit. Based on the output of the show running-config command, which type of view is SUPPORT? secret view, with a level 5 encrypted password root view, with a level 5 encrypted secret password superview, containing SHOWVIEW and VERIFYVIEW views CLI view, containing SHOWVIEW and VERIFYVIEW commands 10. Which three services on a router does Cisco SDM One-Step Lockdown enable? (Choose three. ) SNMP TCP intercepts SSH access to the router Cisco Discovery Protocol password encryption service firewall on all outside interfaces

11. An administrator defined a local user account with a secret password on router R1 for use with SSH. Which
http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/ Page 3 of 12

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

three additional steps are required to configure R1 to accept only encrypted SSH connections? (Choose three. ) configure the IP domain name on the router enable inbound vty Telnet sessions generate the SSH keys configure DNS on the router enable inbound vty SSH sessions generate two-way pre-shared keys 12. Which statement describes the operation of the Cisco SDM Security Audit wizard? The wizard configures a router to prevent unauthorized access. The wizard compares a router configuration against recommended settings. The wizard monitors network data and logs possible unauthorized or malicious traffic. The wizard logs the effectiveness of network security measures for baseline comparisons.

13. An administrator needs to create a user account with custom access to most privileged EXEC commands. Which privilege command is used to create this custom account? privilege exec level 0 privilege exec level 1 privilege exec level 2 privilege exec level 15

14. Which three areas of router security must be maintained to secure an edge router at the network perimeter? (Choose three.) physical security flash security operating system security remote access security router hardening zone isolation

15. Which service is enabled on a Cisco router by default that can reveal significant information about the router and potentially make it more vulnerable to attack? HTTP CDP FTP NTP TFTP 16. Which two operations are required to implement Cisco SDM One-Step Lockdown? (Choose two. ) Choose the One-Step Lockdown feature. Apply the documented network policies. Deliver the configuration changes to the router.
http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/ Page 4 of 12

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

Compare the router configuration against recommended settings. Select the Firewall and ACL task on the SDM Configuration screen.

17. Which statement matches the CLI commands to the SDM wizard that performs similar configuration functions? aaa configuration commands and the SDM Basic Firewall wizard auto secure privileged EXEC command and the SDM One-Step Lockdown wizard class-maps, policy-maps, and service-policy configuration commands and the SDM IPS wizard setup privileged EXEC command and the SDM Security Audit wizard

18. Refer to the exhibit. What is the significance of secret 5 in the generated output? The ADMIN password is encrypted using DH group 5. The ADMIN password is encrypted via the service password-encryption command. The ADMIN password is hashed using MD5. The ADMIN password is hashed using SHA.

19. Which three commands are required to restore a primary bootset from a secure archive on a router on which Cisco IOS resilience is enabled? (Choose three. ) dir command. show flash command. Boot the secure bootset Cisco IOS image using the boot command with the filename. Copy the secure bootset Cisco IOS image to flash using the copy IOS-backup-image flash command. Restore the secure configuration file using the copy config-backup flash command. Restore the secure configuration file using the secure boot-config restore filename command.

Restart the router in ROM monitor mode and display the secure bootset Cisco IOS image name using the

Restart the router, enter privileged EXEC mode, and display the secure bootset Cisco IOS image name using the

20. Which set of commands are required to create a username of admin, hash the password using MD5, and force the router to access the internal username database when a user attempts to access the console? R1(config)# username admin password Admin01pa55 R1(config)# line con 0 R1(config-line)# login local R1(config)# username admin password Admin01pa55 R1(config)# line con 0 R1(config-line)# login internal R1(config)# username admin Admin01pa55 encr md5 R1(config)# line con 0 R1(config-line)# login local
http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/ Page 5 of 12

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

R1(config)# username admin secret Admin01pa55 R1(config)# line con 0 R1(config-line)# login local R1(config)# username admin secret Admin01pa55 R1(config)# line con 0 R1(config-line)# login internal 21. Refer to the exhibit. Which two statements describe the current SDM logging setup? (Choose two. ) Buffered logging will be enabled on the router for Logging Level 7 messages. Buffered logging will be enabled on the syslog server for Logging Level 7 messages. All messages with a trap level of 4 and higher (less critical) will be logged. All messages with a trap level of 4 and lower (more critical) will be logged. The router interface IP address that is connected to the syslog server is 192. 168. 1. 3. The syslog server IP address is 192. 168. 1. 3. 22. What are two characteristics of SNMP community strings? (Choose two. ) A vulnerability of SNMPv1, SNMPv2, and SNMPv3 is that they send the community strings in plaintext. Commonly known community strings should be used when configuring secure SNMP. in an agent. SNMP read-only community strings can be used to get information from an SNMP-enabled device. SNMP read-write community strings can be used to set information on an SNMP-enabled device. 23. What is the minimum recommended modulus key length for keys generated to use with SSH? 256 512 768 1024 2048 24. Which two characteristics apply to Role-Based CLI Access superviews? (Choose two. ) CLI views have passwords, but superviews do not have passwords. Users logged in to a superview can access all commands specified within the associated CLI views. A single superview can be shared among multiple CLI views. Commands cannot be configured for a specific superview. Deleting a superview deletes all associated CLI views. 25. Refer to the exhibit. What two facts can be determined from the output? (Choose two.) The Cisco IOS image and configuration files have been properly secured. ROMmon mode will be inaccessible upon entering the privileged EXEC reload command. The Cisco IOS Resilient Configuration feature is enabled.
http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/ Page 6 of 12

If the manager sends one of the correct read-only community strings, it can get information and set information

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

The Cisco IOS Resilient Configuration feature has detected an image version mismatch. The Cisco IOS configuration files have been erased.

26. What are three requirements that must be met if an administrator wants to maintain device configurations via secure in-band management? (Choose three. ) network devices configured to accommodate SSH a separate network segment connecting all management devices at least one router acting as a terminal server encryption of all remote access management traffic connection to network devices through a production network or the Internet direct access to the console ports of all network devices

New Questions

Why is the usernamenamesecretpassword command preferred over the usernamenamepasswordpassword command? It uses the MD5 algorithm for encrypting passwords. It uses the standard type 7 algorithm for encrypting passwords. It allows the administrator to configure passwords of any length. It does not require the login local command to enable the local database for authentication.

Which two statements describe the initial deployed services of Cisco routers and recommended security configuration changes? (Choose two.) CDP is disabled by default and should be enabled on all interfaces, even when the service is not required. Configuration autoloading is disabled by default but should be enabled, even when the service is not required. ICMP mask reply is disabled by default but should be enabled on untrusted interfaces. ICMP unreachable notifications are enabled by default but should be disabled on untrusted interfaces. FTP is enabled by default and should be disabled. TCP keepalives are disabled by default but should be enabled globally to prevent certain DoS attacks.

Which command is used to verify the existence of a secure Cisco IOS image file? (by Naji Alobaidi) show version dir
http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/ Page 7 of 12

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

show flash show secure bootset

Which three types of views are available when configuring the Role-Based CLI Access feature? (Choose three.) (by Naji Alobaidi) superuser view root view superview CLI view admin view config view

[Update by Xase]

Why is the username name secret password command preferred over the username name password password command? It uses the MD5 algorithm for encrypting passwords. It uses the standard type 7 algorithm for encrypting passwords. It allows the administrator to configure passwords of any length. It does not require the login local command to enable the local database for authentication.

Which statement describes the operation of the CCP Security Audit wizard? The wizard compares a router configuration against recommended settings. The wizard monitors network data and logs possible unauthorized or malicious traffic. The wizard logs the effectiveness of network security measures for baseline comparisons. The wizard performs an analysis of implemented security measures based on a saved baseline.

http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/

Page 8 of 12

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

Which three services does CCP One-Step Lockdown enable? (Choose three.) SNMP TCP intercepts SSH access to the router Cisco Discovery Protocol password encryption firewall on all outside interfaces

Please take note that this CCNA Security Chapter 2 answer is not 100% correct. I got 97.9% for this CCNAS Chapter 2 test. So if you think you have better answer, please share with us. Thank You This entry was posted in Data Network, Network Security and tagged 2012, Answer, CCNA Security, CCNA Security Chapter 2 Answer, CCNA Security Chapter 2 Test, CCNAS Chapter 2 Test, CCNAS v1.1, Chapter 2 Test, Solution, Solution CCNA Security Chapter 2 by InviAlgo. Bookmark the permalink [http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/] .
7 THOUGHTS ON ANSWER CCNA SECURITY CHAPTER 2 TEST CCNAS V1.1

Andy on May 22, 2012 at 1:04 AM said:

you have forgot to add security banner in 8.

InviAlgo on May 29, 2012 at 3:03 AM said:

Thank You

http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/

Page 9 of 12

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

alejandro on May 29, 2012 at 6:16 AM said:

esta exelente el blog y una pregunta cuando va a meter los mas quiz de ccna security

Naji Alobaidi on July 30, 2012 at 5:59 PM said:

new qusstion Which command is used to verify the existence of a secure Cisco IOS image file? show version dir show flash show secure bootset (the answer) Which three types of views are available when configuring the Role-Based CLI Access feature? (Choose three.) superuser view(answer) root view (answer) superview CLI view(answer) admin view config view

http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/

Page 10 of 12

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

InviAlgo on July 30, 2012 at 9:54 PM said:

hi Naji Alobaidi, Thanks for the update. I have updated the question. I believe the answer for the second question are root view, superview and cli view. Anyway, really appreciate your contribution. Thanks again

Naji Alobaidi on August 1, 2012 at 8:44 PM said:

I had my test for ch2 2days ago and I got the correct anwer of this 2 question in cisco system . also I beleve your answer is correct too. Thank you

JM on February 7, 2013 at 1:34 AM said:

Muchas gracias. Pase con 100% todas las respuestas publicadas son correctas. Thanks a lot. I pass with 100% all answers posted is right.

Search Invisible Algorithm: which two statements describe the initial deployed services of cisco routers and recommended security configuration changes? (choose two ), why is the usernamenamesecretpassword command preferred over the usernamenamepasswordpassword command?, which two statements describe the initial deployed services of cisco routers and recommended security configuration changes?, ccna security v1 1, Which command is used to verify the existence of a secure Cisco IOS image file?, ccna security chapter 2 exam answers, Why is the username name secret Answer CCNA Securitypassword Chapter command preferred over the username name password password command?, which two statements describe 7 Test CCNAS the initial deployed services of cisco routers and recommended security configuration changes, ccna security answers, v1.1
Page 11 of 12

Chapter CCNAS

http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/

Answer CCNA Security Chapter 2 Test - CCNAS v1.1 | Invisible Algorithm

3/20/13 4:08 PM

ccna security chapter 5 answers

http://www.invialgo.com/2012/answer-ccna-security-chapter-2-test-ccnas-v1-1/

Page 12 of 12