Fundamentals of Pneumatics: Chapter B-1

123
Chapter B-1
Chapter 1 Fundamentals of pneumatics
Festo Didactic TP101
124
Chapter B-1
1.1 Physical fundamentals Air is an abundant gas mixture with the following composition: ! ! Nitrogen approx. 78 vol. % Oxygen approx. 21 vol. %
It also contains traces of carbon dioxide, argon, hydrogen, neon, helium, krypton and xenon. To assist in the understanding of the natural laws as well as the behaviour of air, the physical dimensions which are employed. The data is taken from the International System of Units, SI for short. Basic units Quantity Length Mass Time Temperature Derived units Quantity Force Area Volume Flowrate Pressure Symbol L m t T Symbol F A V qv p Units Meter (m) Kilogram (kg) Second (s) Kelvin (K, 0 C = 273.15 K) Units Newton (N) = 1 kg m/s2 Square metre (m2) Cubic metre (m3) (m3/s) Pascal (Pa) 1 Pa= 1 N/m2 1 bar = 105 Pa
Newtons Law: Force = mass acceleration F=ma where a is replaced by the acceleration due to gravity g = 9.81 m/s2 Pressure: 1 Pascal is equal to the constant pressure on a surface area of 1 m2 with the vertical force of 1 N (Newton).
TP101 Festo Didactic
125
Chapter B-1
The pressure prevailing directly on the earths surface is known as atmospheric pressure (pamb). This pressure is also referred to as reference pressure. The range above this pressure is known as excess pressure range (pe > 0), the range below is referred to as vacuum range (pe < 0). The atmospheric differential pressure pe is calculated according to the formula: pe = pabs pamb This is illustrated by the following diagram:
Fig. 1.1 Air pressure
Atmospheric pressure does not have a constant value. It varies with the geographical location and the weather. The absolute pressure pabs is the value relative to pressure Zero - Vacuum. It is equal to the sum of the atmospheric pressure and the excess pressure or vacuum. In practice, pressure gauges which only indicate the excess pressure are generally used. The absolute pressure value pabs is approximately 100 kPa (1 bar) higher. Generally, in pneumatics all data concerning air quantity refers to the socalled standard state. According to DIN 1343, the standard state is the status of a solid, fluid or gaseous substance defined by standard temperature and pressure. Standard temperature Standard pressure Tn = 273.15 K, tn = 0 C pn = 101325 Pa = 1.01325 bar
126
Chapter B-1
1.2 Characteristics of air A characteristic of air is its minimal cohesion, i.e. the forces between the air molecules are to be disregarded for operating conditions usual in pneumatics. In common with all gases, air has no particular shape. Its shape changes with the slightest resistance, i.e. it assumes the shape of its surroundings.
Fig. 1.2 Boyle-Mariottes Law
Boyle-Mariottes Law
Air can be compressed and it endeavours to expand. The applicable relationship is given in Boyle-Mariottes Law. At constant temperature, the volume of a given mass of gas is inversely proportional to the absolute pressure, i.e. the product of absolute pressure and volume is constant for a given mass of gas. p1 V1 = p2 V2 = p3 V3 = Constant
127
Chapter B-1
The following example illustrates the above principles. Air at atmospheric pressure is compressed by an air compressor to 1/7th the volume. What is the gauge pressure of the air assuming a constant temperature process ? p1 V1 = p2 V2
Example calculation
p 2 = p1
V1 V2
Note: V2 / V1 = 1/7
p1 = pamb = 100 kPa = 1 bar p2 = 1 7 = 700 kPa = 7 bar absolute Therefore: pe = pabs pamb = (700 100) kPa = 600 kPa = 6 bar
A compressor that produces 600 kPa must have a compression ratio of 7:1 Air expands by 1/273 of its volume at constant pressure, a temperature of 273 K and a temperature rise of 1 K. According to the Gay-Lussacs law, the volume of a given mass of gas is proportional to the absolute temperature as long as the pressure does not change. V1 T1 = V2 T2 or
V = Constant T The volume change V is: V = V2 V1 = V1 The following applies for V2: V2 = V1 + V = V1 + V1 (T2 T1 ) T1 T2 T1 T1
Gay-Lussac law
V1 = Volume at T1, V2 = Volume at T2
128
Chapter B-1
The above equations only apply if the temperatures in K are used. In order to be able to calculate in oC, the following formula is to be used:
V2 = V1 +
V1 (T2 T1 ) 273C + T1
Example calculation
0.8 m3 air at temperature T1 = 293 K (20 oC) are heated to T2 = 344 K (71 oC). How much does the air expand?
0.8m 3 (344K 293K) 293K V2 = 0.8m 3 + 0.14m 3 = 0.94.m 3 V2 = 0.8m 3 + The air has expanded by 0.14 m3 to 0.94 m3. If the volume is kept constant during the temperature rise, this results in the following formula for the pressure increase: p 1 T1 = p 2 T2 or
p = Constant T
General gas equation
The general gas equation is a combination of all three: p 1 V1 p 2 V2 = = Constant T1 T2 In the case of a given mass of gas, the product of pressure and volume divided by the absolute temperature is constant. This general gas equation results in the previously mentioned laws, if one of the three factors p, V or T is kept constant in each case.
! ! !
Pressure p constant Volume V constant Temperature T constant
isobar changes isochore changes isothermal changes

Fundamentals of Pneumatics: Chapter B-1

Uploaded by

Copyright:

Available Formats

Fundamentals of Pneumatics: Chapter B-1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fundamentals of Pneumatics: Chapter B-1

Uploaded by

Copyright:

Available Formats

123

Chapter 1 Fundamentals of pneumatics

Festo Didactic TP101

TP101 Festo Didactic

Festo Didactic TP101

TP101 Festo Didactic

V1 = Volume at T1, V2 = Volume at T2

Festo Didactic TP101

Pressure p constant Volume V constant Temperature T constant

isobar changes isochore changes isothermal changes

TP101 Festo Didactic

You might also like