Pindex System Instructions
Pindex System Instructions
Pindex System Instructions
Laser beam assures easy, quick and reliable pin placement. I Bright laser beam to accurately locate drill position I Clear visibility in all light conditions reduces eye fatigue I Focus-free laser light outlasts conventional lights
Whenever precision is an absolute requirement. I Drill automatically penetrates to exact depth I Manual drilling procedure I Plastic housing
PINDEX DE LUXE If you value additional comfort. I Precision light beam to accurately locate drill position I Manual or pneumatic drilling procedure I Foot switch to activate machine
I Special introductory pin pack I Integrated air blow gun I Metal housing for enhanced durability I Special introductory pin pack
PINDEX Laser Retrofit Kit Upgrade your Mark II* model with the latest technology. Can be easily fitted without special tools.
* Applies to serial number 840101001 and higher. Kit can not be used on DE LUXE models
A well-proven system: PINDEX / TRI-PLUS for easy fabrication of perfect models and dies.
The Pindex System offers many decisive advantages for the fabrication of your models and dies: The model can be poured immediately after impression taking without having to position pins first. The impression remains completely unchanged and results in precise models. The precision pins and sleeves are always inserted accurately as the drill channels are always absolutely parallel, enabling easy removal and repositioning of dies. In addition, the plastic or metal sleeves prevent stone abrasion which may occur during repeated removal and reinsertion of dies.
1.
The model is poured in the usual manner. Care must be taken to maintain a model thickness from base to the marginal extension (without tooth) between 1015 mm in order to avoid fracture du-ring drilling.
7.
If two PINDEX Pins are used per die, the following sizes are recommended: one long pin / white sleeve and short pin / grey sleeve or 2 medium pins / brown sleeves. The advantage of these pins is that they can also be used when the dentition is thin (they need 4 mm less height). Instead of medium pins, conical brass pins with metal sleeves can also be used.
13.
A separating medium is applied to the master model and the base is poured. The use of the PINDEX rubber base mold is recommended. Important: Pouring the base within one hour after fabricating the model improves accuracy as the base and model stone expand at the same rate. A class IV die stone is recommended for the base.
2.
The bottom of the model is trimmed flat. A model trimmer is used to shape the model and a carbide milling machine may be used to remove the palatal area.
8.
The use of PINDEX Dual-Pins with metal sleeves or Tri-Plus Pins with plastic sleeves is particularly indicated in the anterior region.
14.
After the stone base has set, the rubber mold can be removed.
3.
A flat grinder may be used to trim the model flat if the trimming disc is uneven.
15.
The base is trimmed as required.
9.
The unique design of these pins prevents rotation of the die. The hole is notched lingually in order to facilitate placement and to identify the position of the pin.
4.
Before drilling pin channels, each hole location should be plotted on the occlusal surface of the master model and marked accordingly with a pencil. This facilitates precise drilling and subsequent section-ing of dies.
16.
To facilitate articulation, self-articulating PINDEX Pins with sleeves are used. The sleeves are either placed over the metal pins of the PINDEX rubber base mold before pouring the base or cemented into holes that are drilled into the base later using the PINDEX machine.
10.
PINDEX Dual-Pins should be placed with the guiding pin labially, which makes sectioning much easier.
5.
All holes drilled with the PINDEX machine are parallel. As a rule, two holes are drilled per die, unless a PINDEX Dual-Pin or TriPlus Pin is used.
11.
After cementing the PINDEX Pins, the corresponding sleeves are placed over them.
17.
The model is adjusted in the articulator.
18.
Since all pins are parallel, the master model with the pins can be removed in one piece. Thus, the sectioning of the dies can be performed from the bottom side of the model.
6.
PINDEX Pins are cemented with any cyanoacrylate cement. Importent: Always cement short pins first.
12.
Before pouring the base, a strip of wax can be placed over the long pins and positioned over the short pins to close the opening of the sleeve.
19.
Sectioning from the bottom side prevents any injury to the margin extensions. Before breaking the dies, the PINDEX Handsaw may be used to separate them from above.
20.
Safe alignment of the die with Tri-Plus Pins.
13) Pouring of the base using the PINDEX rubber base mold.
21.
The complete PINDEX model is a precise base for the dental technician to work from. 4) Location of drill position with light beam indicator. 16) Self-articulating PINDEX Pins with sleeves in place.
18) Removal of the model in one piece thanks to completely parallel pins.
21) Completed PINDEX model with gingival mask in place (coltne Gi-Mask).
The PINDEX System: All you need for the complete fabrication of precision models and dies.
The patented Tri-Plus Pin (in two sizes) as well as a comprehensive range of speciality pins with matching sleeves, flexible base molds and the Pindex Handsaw complete the system.
Tri-Plus: Superior precision with economy. I Tripod design prevents rotation of the die and ensures optimum retention. I Anti-rotational notch prevents rotation of the die and creates a marking for accurate repositioning of dies. I Ideal for thin, narrow dentition. I Economic plastic sleeves guarantee an accurate fit.
PINDEX Specialty Pins PX-155 Tri-Plus Medium Pin with Plastic Sleeve (16 mm) PX-111B Medium Brass Pin with Metal Sleeve
PINDEX
Ordering Information
PINDEX Accessories
PX-119 PX-120 PX-124 PX-125 PX-146 Carbide Drills Reamer Light Bulbs Laser Retrofil Kit (for Mark II Models only) Flexible Rubber Base Molds (Full arch, Right and Left Quadrants) Flexible Rubber Base Molds (Full arch) Flexible Rubber Base Molds (Right/Left Quadrants) 3 pcs. 1 pc. 10 pcs. 1 pc.
Long Pins & Plastic Sleeves Refill-Pack 100 pcs. Bulk-Pack 1'000 pcs.
PINDEX Medium Pins & Plastic Sleeves PX-102 Refill-Pack 100 pcs. PX-112 Bulk-Pack 1'000 pcs.
PX-147 PX-148
PINDEX Short Pins & Plastic Sleeves PX-117 Refill-Pack 100 pcs. PX-115 Bulk-Pack 1'000 pcs.
Complete with the same Accessories as P-113L Plus: Foot switch Assembly Blow gun Assembly Hex Key Wrench Grounded Cord Assembly
*not available in the EU
PINDEX Dual-Pins & Metal Sleeves PX-154 Refill-Pack 100 pcs. PX-153 Bulk-Pack 1'000 pcs.
PINDEX Articulating Pins PX-118 Refill-Pack PINDEX Self-Articulating Pins & Plastic Sleeves PX-145 Refill-Pack PX-144 Bulk-Pack
TRI-PLUS Pins
Medium Pins & Plastic Sleeves PX-155 Refill-Pack PX-255 Eco-Pack Long Pins & Plastic Sleeves PX-156 Refill-Pack PX-256 Eco-Pack 1'000 pcs. 10'000 pcs.
For optimum performance of your Whaledent PINDEX System, we recommend the use of genuine PINDEX Pins and Accessories. Look for the on all brass PINDEX Pins.
PINDEX Plastic Sleeves for Articulating Pins PX-145S Bulk-Pack 1'000 pcs.
Coltne AG Feldwiesenstrasse 20 9450 Altsttten/Switzerland Tel. +41 (0)71 757 53 00 Fax +41 (0)71 757 53 01 office@coltenewhaledent.ch
Coltne/Whaledent Inc. 750 Corporate Drive Mahwah, NJ 07430/USA Tel. +1 201 512 8000 Fax +1 201 529 2103 productinfo@coltenewhaledent.com
Coltne/Whaledent Ltd. The President Suite-C Kendal House, Burgess Hill Victoria Way West Sussex, RH15 9NF/U.K. Tel. +44 (0)1444 235486 Fax +44 (0)1444 870640 hq@coltenewhaledent.co.uk
9602-DM