Wire-EDM GibbsCAM 2006

May 2006

ProprietaryNotice
This document contains propriety information of Gibbs and Associates and is to be used only pursuant to and in conjunction with the license granted to the licensee with respect to the accompanying Gibbs and Associates licensed software. Except as expressly permitted in the license, no part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, magnetic, optical, chemical, manual or otherwise, without the prior expressed written permission from Gibbs and Associates or a duly authorized representative thereof. It is strongly advised that users carefully review the license in order to understand the rights and obligations related to this licensed software and the accompanying documentation. Use of the computer software and the user documentation has been provided pursuant to a Gibbs and Associates licensing agreement. Copyright 2001-2006 Gibbs and Associates, Inc. All rights reserved. The Gibbs logo, GibbsCAM, GibbsCAM logo, Virtual Gibbs, Gibbs SFP, MTM, SolidSurfacer, and Powerfully Simple. Simply Powerful. are either trademark(s) or registered trademark(s) of Gibbs and Associates in the United States and/or other countries. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. All other brand or product names are trademarks or registered trademarks of their respective owners. Contains Autodesk RealDWG by Autodesk, Inc., Copyright 1998-2006 Autodesk, Inc. All rights reserved. Acknowledgements: Written by Wil Gaffga, Lori Turner & Mike ONeill Thanks to Bill Gibbs, Steve Aughinbaugh & Mario Guerrero for their input and assistance. Printed in the United States of America

Gibbs and Associates 323 Science Drive Moorpark, CA 93021

Modified: 5/30/06

Table of Contents

Table of Contents
GENERAL INFORMATION 1
What Is Wire EDM? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Wire EDM Package Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Wire EDM Package Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

USE AND REFERENCE

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Menu Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 File Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Dimension Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Info Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Toolbar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Display Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 View Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Undo/Redo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Solid Rendering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Return to GibbsCAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Top Level Palette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Wire Strategy/Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Machining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Add or Edit Gluestops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Modify Taper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Specify Conic or Cylindrical Radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 No-Core Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Edit or Modify Geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Resequence the Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Operation Sheet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Machining Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Create CNC code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Using the Package - Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
i

Table of Contents

Wire Configuration/Strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Wire Configuration - Machine Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Machine 32 Wire diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Wire guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Output Z Planes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Part Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Check Travel Limits When Creating Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Machining Report. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Wire Configuration - Machining Strategy Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Skim cut direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Skim cut transition 41 Gluestop Removal: 41 Multiple Parts: 42 Parts with Land: 44 Corner Loop and Corner Relief: 44 Wire Configuration - Display Settings Tab: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Display Settings: 46 Show / Hide: 46 Wire guide display: 46 Simulation Speed: 46 Viewport Selection: 46 Display datums: 46 Agie machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 AGIE Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Charmilles CT machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Creating a Wire EDM Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Add or Edit a GlueStop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Modify Taper Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Wire Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 No-Core Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Number of cuts: 57 Overlap: 58 Dimensioning the Part. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Resequence the Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Machining Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Creating CNC Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Right-Click Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Post Processing Enhancements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 creating your own posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
ii

Table of Contents

About creating your own posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Valid Variable Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Drilling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

TUTORIALS

69

Tutorial #1 Wire EDM 2-Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Tutorial #2 Wire EDM 4-axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Tutorial #3 Wire EDM Open Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

INDEX

101

iii

Table of Contents

iv

GENERAL INFORMATION

General Information

CHAPTER 1 : General Information

WHAT IS WIRE EDM?
Wire EDM (Electric Discharge Machining) is a process by which stock is cut by the means of a gap being burned through the material by the heat produced by electrical sparks between the stock and a wire. The part and wire are immersed in a dielectric (electrically nonconducting) fluid which also acts as a coolant and flushes away debris.

Figure 1: Example of how Wire EDM cuts through material. 12345A charged wire approaches the workpiece in a dielectric fluid. At a certain distance, the charge arcs to the workpiece The wire and workpiece are heated and a vacuum is formed. Material is stripped off the wire and the workpiece. There is a small implosion and more material is removed from the workpiece and wire.

General Information

WIRE EDM PACKAGE OVERVIEW

The Wire EDM package works in conjunction with GibbsCAM and not as a stand-alone product. It is intended to be used as a supplement to existing milling and/or turning clients. To this end, it includes functionality to produce most 2-axis parallel, 2-axis tapered and 4-axis parts. A key feature is the ease of use; therefore, some functions which are only required for special one-off situations are not directly implemented. This is to keep the interface uncluttered and to retain the ease of use. As for most things, there will normally be a work-around to handle these odd situations. The Wire EDM package is designed to produce Wire EDM toolpath from GibbsCAM geometry. Given the fact that EDM is quite different from milling or turning, the Wire EDM package is a selfcontained module that includes machining, simulation and code creation. Using the package you will be able to create punches or dies (closed parts) and:
2-axis parts, with parallel walls 2-axis tapered parts, with or without parallel land 4-axis parts, with or without land Machine open shapes using 2-axis cuts

The 4-axis parts require two 2-axis profiles that represent the top and bottom of the tapered part of the component. Each closed part can have a user-specified number of rough/skim cuts and may have one or more gluestops. You can machine a single part or multiple parts with Wire EDM. When more than one part is required, an overall machining strategy will dictate how the sequence of machining will occur. This will include the option to complete each part, rough each part first or rough and skim each part first. As for the removal of gluestops, an overall strategy indicates whether they are removed after the initial rough cut, after all skim cuts, or left in the part for manual removal. It should be noted that the Wire EDM product is a system that deals solely with the machining of wire parts and contains minimal geometry creation or editing facilities. Most geometry creation or editing must be done within GibbsCAM.

General Information

WIRE EDM PACKAGE DETAIL

This product has been designed with ease of use as a priority. In GibbsCAM, you select the geometry that represent the parts to be cut, then load the geometry into the Wire EDM product where you can indicate how each part is machined, view the toolpath simulation and create CNC code. To create a wire part, you must first define the geometry that represents the part boundaries within GibbsCAM using standard 2-axis geometry. Next, select all of the geometry required to define the wire part(s), including points for gluestop start locations. Wire EDM is designed to apply machining to 2D profiles; therefore, the only geometry entities it requires are 2D lines, arcs, circles and points. Once the geometry is selected, click on the Launch EDM option from the GibbsCAM Wire EDM menu to switch to the Wire EDM package. The Wire EDM package interface is a complete window that covers the GibbsCAM window. The interface is similar to GibbsCAM but is designed for Wire EDM work. The main functions within Wire EDM are:
Wire Strategy: Defining the overall machining strategy, including:

Part orientationland on top or bottom. How gluestops are removedafter rough cuts, after skim cuts or manually. How multiple parts are machinedcomplete each part, rough cuts first or rough/skim first. How skim cuts are transitioned to change offsetseither by adding small lines off/on the part, or tangential arc off/on. Machine configurationtravel limits, wire guide limits.
Machine a part

Select a profile and indicate the start point of the wire for the first gluestop. Indicate how many and which rough/skim cuts are to be used for the selected part. Specify gluestop width. Specify first element to be machined on the profile. Select part type as either parallel, tapered (with optional land) or 4-axis (with optional land). For a 4-axis part, a second profile must be selected to represent the bottom of the part

General Information

Add a gluestop

Add an additional gluestop to a machined part. Select the element for the gluestop, the start point and the gluestop width.
Modify the taper angle of an individual element.

Select any element on a 2-axis tapered part and you can change the angle of taper for that element only. Note that if the element is an arc, then the elements immediately before and after the arc must also be changed. Using the Wire EDM product, you are able to machine either a single part or multiple parts. Each part can be either a 2-axis part with parallel walls, 2-axis tapered (with or without land) or 4-axis (again with or without land cuts). The product enables you to allocate attributes to each part and to specify an overall strategy for all parts. Attributes applying to each part include:
The number of skim cuts The number of gluestops (and their respective locations) The type of part (2-axis, 2-axis tapered, 4-axis, etc.) The direction around the part

The overall machining strategy covers:

When gluestops are removed - after the first roughing cut, after all the skim cuts, or not removed at all (manually removed) If all cuts are the same direction around each part, or alternate skim cuts are reversed (to reduce the number of times the wire need to be broken and re-threaded) How offsets are changed between each skim cut (by adding small moves away from the part and back on again) Whether all of each part is completed before moving to the next one, or if all parts are roughed and then skimmed

The strategy can be changed at any time and the toolpath will automatically be updated to reflect the changes.

USE AND REFERENCE

Use and Reference

CHAPTER 2 : Use and Reference

OVERVIEW
GibbsCAM Wire EDM is able to machine both open and closed profiles and create 2-axis or 4-axis parts.
Each 2-axis part (parallel or tapered walls) requires a single closed profile and a point to represent the start position (wire thread location). Each 4-axis part requires two closed profiles, one to represent the top of the part and one to represent the bottom. You will also need a point for each gluestop start position. Open profiles may be machined, but these can only be done with parallel or tapered cuts (not 4-axis). They do not need a gluestop (it is optional) and only require a point for the wire thread position if the wire starts away from the profile. You are also able to create No-Core Cutting. This functionality enables you to either remove a free-form

shape or circular hole. Free-form shapes require a closed profile and a point for the wire start position, and holes simply require a circle. Within GibbsCAM, you select the profiles and points required to define each part together with any profiles and/or circles for No-Core cuts. Click on Launch EDM from the Wire EDM menu and you will be automatically taken into the Wire EDM product.

T I P

If you do not select any geometry before clicking on the EDM option, you will be given the opportunity to start the EDM package without transferring any geometrythis is useful if you want to check/modify a previously saved Wire EDM program.

INTERFACE
The Wire EDM interface resembles the GibbsCAM interface and uses both icons and pull-down menus. Virtually everything is done by using the icons at the top and right of the screen, but a list of the pull-down menu options is included for completeness. If you leave the mouse over an icon, you will get a short Tooltip describing the functionality of the icon. By right-clicking on an icon you will get a more detailed description. Most of the screen area, the Workspace, is reserved for graphics. Like in GibbsCAM, the stock area is displayed with grid lines. At the bottom of the screen area are 2 boxes. Each time you select a

Use and Reference

command that requires input, the name of the command will be displayed in the first box and the type of input required will be displayed in the second box.

1 - Menu 2 - Toolbar

3 - Top Level palette 4 - Workspace

5 - Input requirements 6 - Mouse Position

Figure 1: Elements of the Wire EDM interface.

10

Use and Reference

MENU ITEMS
The pull-down menus at the top of the screen contain the following functions:

11

Use and Reference

File Menu

Revert to original data: Reverts

back to original geometry from GibbsCAM. All functions, commands and processes that you have executed will be erased. Open part: Open a previously saved Wire EDM part. Save part: Save current part. Save part as : Save current part as a new filename. Notes: Select this item to enter data about the part file.

Copy (clipboard): Copy graphics to clipboard. Print: The Print sub-menu provides access to several print

options.
Print current view: Print current view. Print part full size: Print entire full sized part.

Plot to scale : Brings up a dialog in which you can select or

enter the exact scale at which you wish to plot or print. Printer set-up: Change printer settings.

12

Use and Reference

Graphics print config: Configure

how

graphics

are

printed.
Exit System: Exit Wire-EDM and return to GibbsCam.

XY Point: XY position of a point. Line horizontal: Dimension a line using its horizontal distance (X). Line vertical : Dimension a line using its vertical distance (Y). Line parallel : Dimension a line using actual line length. 2 pts horizontal : Dimension between two points (horizontal distance). 2 pts vertical: Dimension between two points (vertical distance). 2 pts parallel: Dimension between two points (actual distance). Angle of line : Dimension the angle of one line. Angle 2 lines: Dimension angle between two lines. Arc radius: Dimension the radius of an arc. Arc angle : Dimension the included angle of an arc. Configure: Configure dimension text height and decimal places.

Dimension Menu

For more details on Dimensions see page 23.

Info Menu
Measure: Measure the distance between two points. Select the

two points and an alert dialog will open with the data requested
Area/perimeter: Calculate the area/perimeter of a profile. Select

the closed shape and an alert dialog will open with the data requested.

13

Use and Reference

Calculator: Brings up the desktop calculator that includes memory/recall and trig functions.

Settings Menu
Points : Show/hide gluestop start points/circles. Dimensions: Show/hide dimensions. Axes: Show/hide axes (XY, XZ or YZ) symbol. Language: Select operating language. Interface: Select the interface style you prefer to work with. Gibbs style fixed is the default and locks the Top Level palette in the top right corner. Gibbs style - floating unlocks the Top Level palette so it may be placed anywhere on your screen.

14

Use and Reference

Setup post editor: Allows the user to assign specific preferences for post editing.

Setup Technology data: This dialog allows you to define a list of material types, wire types and wire diameters. In Wire strategy/configuration settings, drop down menus are used to select material and wire. The corresponding technology data entered here will be automatically loaded into those lists.

15

Use and Reference

Hot keys: Customizes hot key commands.

Display
Redraw: Redraw will force a screen refresh that will clean up the display of items. Full: Zoom full will shrink or grow the display of items in the Workspace to fit

within the Wire EDM window. Window: Select this item for a drag-zoom. Zoom in: Zoom in by 10%. Zoom out: Zoom out by 10%. Pan left: Pan left by 10%. Pan right: Pan right by 10%. Pan up: Pan up by 10%. Pan down : Pan down by 10%. Viewports : Select the multiple viewports configuration. The Viewports command can split the screen into two, three, or four views. The setting is controlled by the Select Viewport layout dialog which can also be accessed from the Multiple Viewports button. Simply click on one of the six configurations to change the Workspace display. Each viewport can be individually set to the view you prefer.

16

Use and Reference

Help
About GibbsCAM Wire EDM: Displays information about the product and the version currently being used. Posts : Displays a help window (shown below) with topics relating to EDM post processing.

17

Use and Reference

TOOLBAR
The Toolbar provides quick access to commonly used commands such as setting the display and view settings, part configuration and undo/redo functions.

1 - Display Commands 2 - Configuration 3 - View Commands

4 - Undo / Redo 5 - Miscellaneous Commands 6 - Solid Rendering

7 - Return to GibbsCAM

Display Commands
The first four buttons control the display of items in the Workspace, similar to several of the items in the GibbsCAM View palette. These commands include Redraw, Zoom Full, Zoom In and Zoom Out.
Redraw: Redraw will force a screen refresh that will clean up the display of items. Zoom Full : Zoom Full will shrink or grow the display of items in the Workspace to fit within the Wire

EDM window.
Zoom In: The Zoom In command will increase the display of items in the Workspace by 10%. You may

also Zoom In on the part by using Shift + + or the mouse wheel or by dragging the mouse on an area that you want to zoom in on.
Zoom Out: The Zoom Out command will decrease the display of items in the Workspace by 10%. You may also Zoom Out on the part by using Shift - - or the mouse wheel.

In addition, Ctrl + arrow keys will pan the part in the specified direction. Right-clicking a part and dragging it will also move it in the specified direction.

18

Use and Reference

Configuration
The Configuration button opens the Configuration dialog which provides for updating configuration settings, including display settings on elements.

Show-Hide: This set of checkboxes controls what is displayed in the Workspace. Checking Dimensions

will display the dimensions created using the Dimension icons, while Axes display the parts axes as in GibbsCAM. Profile start will draw an arrow indicating the direction in which a cut will start. Dir indicators is a series of arrows showing the direction of a cut, drawn along geometry and toolpath. Checking Rapid moves will display rapid moves as dotted lines so you can see where the machine is moving.
Command Repeat: Activating the Command repeat checkbox allows you to perform a function, such as breaking geometry, multiple times without having to re-select the command. When a function, such as Split Element, is chosen, the system will remain in that mode until another function is selected. This is very convenient when performing a series of commands using the same function. Display Grid : Activating the Display Grid checkbox draws the stock boundaries using grid lines. Units: These radio buttons toggle between Metric or Inch measurement units. Redraw: After making the above selections, click Redraw to instantly see the results of your changes

without closing the Configuration dialog.

19

Use and Reference

Colors: This dialog allows you to configure the display colors of the Wire EDM system. Click on the name of the item to change the color. Check Use wire color for each wire cut to be rendered in a different color (if unchecked, all machining is rendered in the same color). Backup: This setting allows you to designate the backup file and frequency of backups. Select the
Autobackup enabled

checkbox to activate this function.

Undo: This setting allows you to set the number and types of undos the system tracks.

View Commands
The View control buttons set the view orientation of the part geometry. Settings include Plan, Front, Side, Isometric, Multiple Viewports, and Mouse View Rotation.
Plan: The Plan button sets the view to the top of the part, looking down on the XY plane. Front : The Front button sets the view to the front of the part, looking at the XZ plane.

20

Use and Reference

Side: The Side button sets the view to the top of the part, looking at the YZ plane. Isometric view : The Isometric button sets the view to a three-axis view of the part. While in isometric view, click the Dynamic Rotation button and the cursor will change into an axes icon when it is positioned over the part in isometric view. Left-click and hold the mouse button to dynamically rotate the view. Remember to deactivate this feature after you have finished with it by right clicking or by clicking on the icon again. Multiple Viewports: The Multiple Viewports button can split the screen into two, three, or four views. The

setting is controlled by the Select viewport layout dialog which is accessed from the Multiple Viewports button. Simply click on one of the six configurations to change the Workspace display. Each viewport can be individually set to the view you prefer.

Figure 2: The Select viewport layout dialog and a part displayed with multiple viewports

Undo/Redo
The Undo and Redo buttons allow you to remove changes on a part. The undone changes can also be re-done. The Undo command logs the last 100 modifications made to the part file including syncs, geometry changes and machining functions. The Undo function may be fine tuned or disabled in the Configuration dialog.

21

Use and Reference

Solid Rendering
Clicking on the Solid Rendering button will change the stock diagram to a 3-dimensional solid image. When you click the Solid Rendering button new icons will appear in the Top Level Palette. These buttons provide control over Solid Rendering. The view can be rotated, panned and zoomed as the part is being cut. Clicking Play will begin the Solid Rendering. Clicking on Step Forward moves the rendering forward in small increments. The remaining buttons are Stop, Rewind and color adjusting slides.

Return to GibbsCAM
Clicking the Return to GibbsCAM button will switch the user back to the GibbsCAM environment where the user may make changes to the geometry. Selecting the new geometry and re-launching EDM will send the user back to the Wire EDM environment,

22

Use and Reference

TOP LEVEL PALETTE

This palette contains icons to access setting the wire strategy and machining settings.
Wire Strategy Machining Gluestop Taper Radius Sync No Core Cutting Geometry Dimensions Information Sequence Operation Sheet Simulation Create code

Wire Strategy/Configuration
Clicking on this button opens the Wire strategy/configuration settings dialog. This dialog allows you to set the machining methodology, wire guide locations, 4-axis display settings and any parameters that relate to the whole job. The Wire strategy/configuration settings dialog is discussed in greater detail under Wire Configuration/Strategy on page 31.

23

Use and Reference

Machining
Clicking on this button allows you to create or edit a wire part. Select the geometry that represents the profile to be cut. On 4-axis parts, the top profile should be selected. More information may be found in the section Creating a Wire EDM Part on page 52.

Add or Edit Gluestops

Clicking on this button allows you to add, edit or delete a gluestop. Select an element (line or arc) on an existing wire part where you require an additional gluestop to be created. Select the start point for the wire and a gluestop will be added. If you select an element that represents an existing gluestop, you will be able to change the gluestop attributes (gluestop width) or to remove the gluestop altogether. More information may be found in the section Add or Edit a GlueStop on page 55.

24

Use and Reference

Modify Taper
Clicking on this button enables you to modify the taper angle of individual or a range of elements on a 2-axis tapered part. Simply click on the element of the part that you want to change and you will be shown the overall part taper angle and the angle for the selected element. Enter a new angle and you will see the part change accordingly. More information may be found in the section Modify Taper Angle on page 56.

Specify Conic or Cylindrical Radius

Clicking on this button enables you to specify whether the radius of an arc is conical or cylindrical or you may enter your own radius value. Cylindrical arcs have a constant radius while conic arcs have a larger radius at the end of a taper. This option can be applied to tapered parts only.

25

Use and Reference

Sync
Each 4-axis part is automatically synchronized to end points of an element on the selected top and bottom profile(s). This icon enables you to add additional sync points around the profile. Click near the end of an element on the top profile, then as you drag the mouse around you will see a line being rubber-banded from the end of the element. Click near the end of the element that you want to sync with on the lower profile and the machining for that part will be resynchronized. More information may be found in the section Wire Synchronization on page 57.

No-Core Cutting
Once you have clicked this icon, you select either a closed profile or a circle. If you select a profile, you will be asked where you want to start (and must select a point), the wire overlap and the number of skim cuts as well as selected skim cuts. If you select a circle, you will be asked for the initial hole diameter and the hole will be machined by a series of ever-increasing arcs to remove the material between the initial diameter and the final (circle) diameter. More information may be found in the section No-Core Cutting on page 57.

Edit or Modify Geometry

Clicking on this button enables you to edit or modify existing geometry. Commands include Fillet, Chamfer and Split an Element. More information may be found in the section Dimensioning the Part on page 59.

Dimensions
Clicking on this button will activate the Dimension dialog. This will allow you to add dimensions to your part. Options include Line Horizontal, Line Vertical, Line Parallel, 2 Points Horizontal, 2 Points Vertical, 2 Points
Parallel, XY Point, Angle of Line, Angle of 2 Lines, Arc Radius, Arc Angle and Text Configuration. These items are also accessed from the Dimension menu. The

26

Use and Reference

descriptions of each item are under Dimension Menu on page 13 and more details on dimensioning a part may be found in the section Dimensioning the Part on page 59.
Information

Clicking on this button will activate the Info dialog. The Info dialog has several utilities. Commands include Any Construction
Element, Any Non-construction Element, Measure, Area/Perimeter and Calculator. Select an element to get data relating to its start

point, end point, angle etc. More information may be found in the section Information on page 60.

Resequence the Operations

Resequence the order of machining. The machining is normally carried out in the order in which you have created it. To change this sequence, click on this icon and simply select each part or No-Core shape/circle that you want to machine in the order that you want to cut them. If you only select some parts, then those selected will be machined before the others that were not selected. Note that all No-Core cuts will always be performed before the parts are cut. More information may be found in the section Resequence the Operations on page 62.

27

Use and Reference

Operation Sheet
Clicking on this button generates an Operation sheet that includes part notes, a listing of all operations and a part preview. The content may be customized by selecting the Notes item from the File menu. The data entered in Notes will be reflected in the Operations sheet.

28

Use and Reference

Machining Simulation
Click this button to simulate the machining. You can select the speed of simulation using the scroll bar at the top of the dialog. You can also switch to Step mode, so that you can check each individual movement of the wire. More information may be found in the sectionMachining Simulation on page 62

Figure 3: The Simulation dialog and a rendered part.

29

Use and Reference

Create CNC code

Clicking this button will allow you to simultaneously generate the CNC code and view the Cut Part Rendering. When Go is clicked, you will be prompted to enter a program number. When you click OK after entering a program number, the rendering and code generation will begin. The code is saved to the file W1 on your C:\ drive by default. More information may be found in the sectionCreating CNC Code on page 63.

Figure 4: Dialogs involved in creating code.

30

Use and Reference

USING THE PACKAGE - DETAIL

WIRE CONFIGURATION/STRATEGY
The Wire Strategy/Configuration Settings dialog is split into three areas, each selected by clicking on the relevant tab near the top of the dialog.

Wire Configuration - Machine Configuration Tab

The settings found in the Machine configuration tab enable you to set the parameters for the machine that will be used to cut the part.

31

Use and Reference

Machine
Select the machine that you will be creating code for. A list of machines configured on your system will be available on the pull-down menu. If you click on the Configure button to the left of this menu, you will be able to modify parameters specific to the selected machine, including machine travel limits and wire guide limits.
Configure: Pressing this button opens the Wire configuration settings dialog that allows you to set the

physical travel limits of the wire guides and the wires taper limits.

32

Use and Reference

Technology Settings: There are three options in the Technology data under the Technology settings tab, Do
not use technology data, Use technology settings, and Use technology table.

For the latter two options, you can specify up to six different technology values for each machine you have. Select the number of values you require by using the scroll arrows next to Number of fields. Clicking on the box to the right of the Field name allows you to enter your own field name. For example, you may wish to enter Offset diameter, Feedrate, Flushing or Epak number. Once you have configured how many technology fields you want to use together with their corresponding names, you can then enter the actual data to be used. If you check the units box, EDM knows that particular field is an inch/metric value and that you will be defining the content using the current units (inch or mm). If you use that table later in a part that has the opposite units, it will either multiply or divide the value by 25.4 to give the required data.

33

Use and Reference

When employing the Use technology settings option, this is done by clicking on the Technology settings button under the Machine section in the Wire strategy/configuration settings dialog.

The above table enables you to provide values for each technology field against each wire number that you will use to machine the parts. You can specify up to eight different wire numbers, one roughing and seven skim. The values entered in this table will be available next time you start the system; alternatively, you can save specific sets of data and reload them later and therefore build up a library of technology data for different material types, thicknesses, etc. When Use technology table is selected, click the Technology table button under the machine section in the Wire strategy/configuration settings dialog to define the technology table using the dialog shown above. A technology table contains a number of pre-defined machining methods which indicate how many skim cuts are to be used and the settings associated with the rough and each individual skim cut. In the example shown above, we have selected Rough + 1 Skim and entered data for these two cuts. Once the technology table is defined, click Save table to save it for future use.
Set Feedrates: Set Feedrates checkbox at the bottom of the Technology Settings dialog enables the input of

feedrates against each wire offset. If this checkbox is enabled, the Machining Report button at the bottom of the Wire strategy/configuration settings dialog becomes active. The Machining Report is also discussed on page 39. 34

Use and Reference

By using this command, you can quickly see how much time elapses until the first gluestop. You can simply select a new strategy and get a new estimate to judge which might be the best strategy under the circumstances.
Machine Settings: The Machine settings tab is used to configure datum settings.

Select Use Datums to define up to ten sets of datum. The Datum fields section can be used to select the desired fields by selecting the corresponding checkboxes. When datums are enabled, the Datums button becomes available under the Machine section of the Wire strategy/ configuration settings dialog. Click this button to access the Wire Datum Settings dialog as shown here. You simply check the datums you want to use. Allocate a unique name to each datum, and then enter the data associated with the datum. If you checked the XY position field, you will be offered an XY buttonclick on this to select a point from the screen to automatically fill in the Work shift X and Work shift Y position boxes. 35

Use and Reference

After defining each datum, you will see a new right-click menu the next time you right click on a machined shape to change its properties. The right-click menu contains a list of the names of the datums you have defined. Select the required name in the list to associate the shape with the required datum. If you are using the Z top and Z thickness datum attributes, the part will be displayed at its new Z position the next time you redrawthis provides the ability to program stepped plates with parts of different thicknesses (you can also define optional new wire guide heights). All of the datum parameters you define are available to the post processor, including the ability to automatically shift XY positions by the defined values, if required.
Wire can be threaded at an angle: When Wire can be threaded at an angle is checked, the wire can be threaded when the two wire

guides are not directly above one another. Wire start positions are defined by XY and UV positions. When you define a 4-axis part with this option selected, the system will ask you for a start position on both the top and bottom profiles.

Wire diameter
The Dia is the diameter of the wire you will be using. The different wire types that may be used are available on a pull down menu.

Wire guides
The Z height of the upper and lower wire guides are used both for simulation of the machining and also to calculate the XY/UV coordinates for 4-axis code.

Material
The thickness of the stock and the Z position of the top of the stock should be entered in these text boxes. This is important for both drawing geometry and generating output data. The different materials that may be used are available on a pull down menu.

36

Use and Reference

Output Z Planes
These entries are used when generating code. It is recommended that you click on the Same as top and bottom of material button to automatically set these values based on the material settings. The system outputs code based on the Z height of XY data. If your part is on a block, a custom arrangement or below the top of the table, you will need to enter the proper values manually.

Figure 5: Output is done at the Z height of the XY data.

Part Orientation
Specify how the part is situated. Rendering will be modified to match your setup.

Check Travel Limits When Creating Code

If this option is checked, you will get a warning message if you try to move outside the travel limits you set for your machine.

37

Use and Reference

Advanced Settings
The Advance Settings button opens a dialog that contains additional strategy options for control over three areas of machining, No-Core circles, Circular dies and the entry moves made on Rough cuts.

No-Core Circles - Skim cut entry positions : This option is similar to that for circular dies (below). The skim

cut entry positions may be adjusted for No-Core operations on a circle.

T I P

To get skim cut entry position evenly spaced, the following conditions must be met: You must select the machining strategy to remove gluestops with the rough cut. The shape must be a circle (not a circular contour).

Rough cut entry moves : This option offers the facility to select the type of entry move for the rough cut for each shape. The line and arc option will require the input of an arc radius (which will be used for all entry moves).

When a line and arc entry is selected, the line will start at the wire thread position and end tangent to the arc (to form a teardrop shape). If the wire start position is less than the arc radius from the shape, then the line cannot be tangential to the arc (as it will start inside the arc) - in such cases 90 degrees of arc will always be used. For parts with land, a line-arc will only be used for roughing the land, unless the skim taper options has been selected on the second page of wire strategy settings. There is no gouge checking for any arc entry moves, the user must ensure that gluestops are not placed such that the arc will cut through any other part of the shape. In cases where land parts have line-arc entries for both land and taper, the user must check that the two arc entries do not create any loose material which may fall from the part.

38

Use and Reference

Circular dies - Skim cut entry positions: When gluestops are removed with the roughing cut, dies will have

the slug removed before any skim cuts. For circular dies, we have added the option to adjust the entry moves for each of these skim cuts such that each skim will start at a different position. The entries positions will be equally divided around the circular shape, so for 3 skim cuts they will be 120 degrees apart, 4 skim cuts 90 degrees apart and so on. Each skim cut will comprise 2 circular arcs (of equal length) and each skim cut will go past the previous exit position. So for 3 skim cuts, each skim cut will comprise two 240 degree arcs (to cover 360 degrees, plus 120 degrees to the next skim cut start position). To get skim cut entry position evenly spaced around a contour, the following condition must be met. You must select the machining strategy to remove gluestops with the rough cut. The shape must be closed circular contour. The shape must be a die (start point inside the circle).

T I P

Machining Report
The Machining Report command quickly calculates how much time elapses until the first gluestop. This option uses the feedrates together with the selected strategy to provide a simple report showing the total estimated time, time per wire offset, and distance cut with each wire offset. It will also list the time between each gluestop.

39

Use and Reference

Wire Configuration - Machining Strategy Tab

This is where you define the strategy to be used for the whole job. Click on the second tab, Machine strategy, you will get the following options:

Skim cut direction

All cuts in same direction indicates that the roughing cut and all skim cuts will be performed in the same

direction around the part. Each cut will start with a wire thread at the start position, lead into the gluestop and follow around the part until you reach the end of the part. The wire will then be broken so that it can be moved to the start of the next cut. If the part has more than one gluestop, the wire will be broken and re-threaded between each pair of gluestops. When you select the Reverse alternate cuts option, you have the option of a Retract distance. With this option selected, instead of stopping at the end of a cut and breaking the wire, it reverses back along the profile to perform the next skim cut. The Retract distance option enables the wire to be moved away 40

Use and Reference

from the part (normal to the end of the element) so that a new offset can be selected. The wire is then moved back onto the part with the new offset before reversing back around the shape. Thus, for a part with a single gluestop, the wire only needs to be broken once. For multiple gluestops, the roughing cut and all skim cuts will be performed using alternately reversed cuts between each pair of gluestops. So, for a part with three gluestops, the part will be machined as follows:
All cuts will be performed between the first and second gluestop. Wire break, then re-threaded at start position for second gluestop. All cuts performed between second and third gluestop. Wire break, then re-threaded at start position for third gluestop. All cuts performed between third and first gluestop. Wire break.

Skim cut transition

When all skim cuts are performed in the same direction around the part, the wire offset needs to be changed between each cut. This option provides for the wire to be moved away from the part in order to change the offset before proceeding with the next cut. The move away can be either a straight line or a tangential arc. When you select the Reverse alternate cuts instead of stopping at the end of a cut and breaking the wire, it reverses back along the profile to perform the next skim cut. The Retract distance option enables the wire to be moved away from the part (normal to the end of the element) so that a new offset can be selected.

T I P
Gluestop Removal:

Please note that transitions on tapered or 4-axis parts can only be made by a line. Arcs are only available for parallel cuts.

There are three options in this area. The first, Manually remove gluestops, simply means that all of the gluestops will be left in place. This option is useful when parts are held in with small micro-joints, so that the parts do not fall out and the job can be run unmanned. With the Cut gluestops after rough cut option, the wire will stop at each gluestop (ready for the operator to clamp the part), then continue to remove the gluestop, with the final gluestop on the part

41

Use and Reference

being extended by an optional extend distance. The wire will either be left in position on the part at the end of the gluestop, or an optional arc away from the part can be added.

T I P

If you use this option, since all of the gluestops will be removed before any skim cuts, the reverse skim cuts option will be ignored. There is no need to reverse cutsall skim cuts will follow the same direction.

With the Cut gluestops after all skim cuts option, each cut will leave the gluestops in place. Only when the final skim cut has been performed will the gluestops be removed. When you select this option with the Complete each part wire strategy, the rough and skim cuts are treated as one set of cuts when pairing the cuts together (the wire is reversed after the rough cut, avoiding the need to break and rethread). If you check the Skim all gluestops box, then the gluestop will be cut with the same number of skim cuts as the part; otherwise, it will be removed by a single roughing cut.

Multiple Parts:
The Complete each part option indicates that each part must be roughed, skimmed and the gluestops removed before moving onto the next part. 2 Stage, Rough first roughs all parts, then goes back to each part for a second stage of skim cuts and gluestop removal before proceeding to the next part. 2 Stage, Rough-skim first roughs and skims each part, and then goes back to each part for a second stage of cuts consisting of the removal of gluestops. 3 stage, rough-skim-gluestops roughs each part skims each part, and then removes the glues stops from each part. Selecting the Custom Strategy checkbox will enable the Select button. Click this button to define your individual strategy for machining multiple parts using the dialog shown below.

42

Use and Reference

You will see a list of each operation type (rough, skim, gluestops) which is further divided by part type (parallel, tapered, etc.). Deselect Treat open and closed profiles the same or the Treat punches and dies the same checkbox to get an extended list where parts are further subdivided into open and closed shapes as shown.

There are also three options available for removal of gluestops. They are Cut gluestops after all skim cuts, Cut gluestops after all rough cuts and Manually remove gluestops for Open profiles, Dies or Punches. These gluestop options are fully discussed on page 41. A custom strategy defines how to machine multiple parts using up to eight separate passes across the entire machining process. All of the operations to be undertaken for the first pass will be listed in the first (left-hand) box. To move an operation to the next pass, simply click on it to highlight it, then press the left or right arrow key to move it to the previous or following passes.There are four defined passes

43

Use and Reference

in this example. there will be four operations on the first pass, two on the second, only a parallel skim cut on the third and so forth.

You can save or load your custom strategies for use on other jobs by using the buttons at the bottom of the dialog.

Parts with Land:

This set of radio buttons define how land may be handled. The options include roughing the land before the taper, roughing the taper first or roughing the taper only (ignoring the land). Check Skim the taper to skim both the land and the taper for parts with land, and uncheck this option to skim the land only.

Corner Loop and Corner Relief:

These two mini-tabs enable automatic corner looping and corner relief moves. They both work in similar fashion and you can choose to use either, both, or neither of the options. Corner looping and corner Relief is available for nocore parts as well. 44

Use and Reference

When Add loops to external corners is enabled, all parallel cuts (including the land on parts with land) will have corner loops automatically added to external corners (including external corners inside dies). A loop will be added by extending the two elements by at least the distance specified (which can be a multiple of the wire diameter or a specific value, selected by using the pull-down menu). Having extended the elements, a tangential arc will be added from the end of the first element to the start of the second. Note that the radius of the loop will be automatically calculated and will be larger for sharper corners. The Minimum angle setting is used to enter the smallest change in angles between elements before a loop is added. Three options are offered for corner relief: Do not relieve internal corners, Add loops to internal corners, and Add lines to internal corners. Loops are added by moving back along each element by the specified distance (again, either a multiple of the wire diameter or a specific value) and adding an arc whose center is located at the original corner position. Lines are added at the corner itself, one away from the corner and another back along the same path to return to the corner. These lines will follow a path that bisects the angle of the corner; the length of each move is the distance specified (same as loop radius).

Wire Configuration - Display Settings Tab:

The third tab in this dialog provides some control on how the parts are drawn.

45

Use and Reference

Display Settings:
Since each skim cut follows the same path as the first roughing cut, if they were all drawn on top of each other, you would have no idea how many cuts had been programmed. Therefore, each skim cut is displayed above the previous cut, with the Z distance between each skim cut being set on this form. Four-axis parts are drawn with a series of lines between the top and bottom profile to indicate how the two profiles are joined together and synchronized. The distance between these 4-axis lines is also set on this form using Distance between 4 axis display lines.

Show / Hide:
You can optionally switch off the display of skim cuts, 4-axis lines and sync lines that have been interactively added to 4-axis parts. By pressing the button to the left of the colored boxes, you are also able to change the colors used to display the lines used for 4-axis display. This is particularly useful for differentiating between system-defined syncs and user-defined syncs.

Wire guide display:

Choose your preferences for the Wire guide display; you may prefer to display them as Rendered (small), or Rendered (large).
Extend wire through guides is used to provide a more realistic simulation. The wire will be drawn through and past the guides.

Simulation Speed:
Adjust the Simulation speed during rendering using the slide control in this section.

Viewport Selection:
Under Viewport selection, choose Mouse click to select a particular viewport by moving the mouse over the view and clicking on it. Choose Mouse over to automatically select the view that the mouse is over.
Mouse over makes it much faster to move between views and to use the mouse zoom and/or

T I P

pan to get the display you want. However, should you wish to change a particular view (say, plan view to side view), make sure that you move the mouse out of the view and up to the icon to select the new view at the top of the screen without going through another view (since you will simply select a new view as the mouse moves over it). If this is something that you do more often, you may prefer to select Mouse click instead of Mouse over.

Display datums:
Under the Display datums section, you have the option of displaying datum symbols at the XY position defined together with the name of any datum associated with a particular shape.

46

Use and Reference

AGIE MACHINES
This version includes Agie Evolution, Excellence and Progress post processors. When one of these posts are selected, a new button, AgieCut Settings, will be available on the first page of Wire Strategy/ Configuration Settings.

The Agie post processors require the selection of Material type, Wire type and Machining quality. This selection is displayed by clicking the Agie Settings button which opens the new input form shown on the right.
Quality: The surface quality of a

whole workpiece.The quality of machining is done by these five parameters.

Ra: Roughness. Te: Corner precision. Tkm: Tolerance of form. Speed high: Priority for speed. Quality high: Priority for high quality.

47

Use and Reference

Output Taper Parts As: There are two different taper modes: Agie Standard Conic: Taper value is constant on the whole contour (cylindrical). 4 Axis Geometry: The standard 4 axis taper (non-cylindrical). Material: Material of the pieces that are defined in a technological database. The default material is

Cold die Steel.

Wire: Wires are defined in a technological database insie the AGIEVISION. The default wire is Cobra

Cut A 0.25.
Entry / Exit Start Holes / Minimum Dia (num): The minimum diameter of all Entry and Exit Start Holes.

Having selected an Agie post, you will be offered a new machining type for closed contours, that of collar machining which is specific to the Agie machine. By checking the new Collar option, you will be offered a new set of parameters that enable you to define a collar part.

If you select the Open to the top option, you will be asked for the Z1 and Ang1 values, in order to define the chamfer at the top of the part. The Open to the bottom option will also ask for Z1 and Ang1 values, this time used to define the chamfer at the bottom of the collar. The third option Open to both sides (as shown above will ask for values to define both chamfers. Angles are in degrees and Z1, Z2 are both measured from the top of the part. Note: In this version, you will see the resulting part displayed as a parallel part (no chamfers shown), but the required collar definition will be output in the NC code. 48

Use and Reference

AGIE OUTPUT
When you create code using an Agie post processor, the NC output filename you select is used as the basis for all of the output files created. For example, if you provide a filename of c: \Evolution\ABC, the following files will be created (all in the c:\ABC folder):
ABC.SBR and ABC.SBL

The job files Geometry files

For each part (contour) you will get 2 files

ABCn.ISO and ABCn.ISR

Where n is the part number (1 for the first part, 2 for second and so on). For each no-core part you will get 4 files:
ABCnr.ISO and ABCnr.ISR ABCns.ISO and ABCns ISR

Geometry files for roughing Geometry files for skim cuts

For example, for a job with 2 parts and 1 no-core circle, you will get the following files (for the input filename ABC):
ABC.SBR and ABC.SBL ABC1.ISO and ABC1.ISR ABC2r.ISO and ABC2r.ISR ABC2sISO and ABC2s ISR

Job files Part 1 (contour) Part 2 (no-core roughing) Part 2 (no-core skim)

Since the Agie post processor expects filenames to be no more than 8 characters, you must ensure that the filename you specify is no more than 5 characters (files are numbered, so if you have more than 10 parts, you must only use 4 characters.). You must also make certain that you do not add any suffix to a filename.

Note: In this version, you will see the resulting part displayed as a parallel part (no chamfers shown), but the required collar definition will be output in the NC code.

49

Use and Reference

The Agie post processors require the selection of Material type, Wire type and Machining quality. This selection is displayed by clicking the Agie Settings button which opens the new input form shown on the right.
Quality: The surface quality of a

whole workpiece.The quality of machining is done by these five parameters.

Ra: Roughness. Te: Corner precision. Tkm: Tolerance of form. Speed high: Priority for speed. Quality high: Priority for high quality. Output Taper Parts As: There are two different taper modes:

50

Use and Reference

CHARMILLES CT MACHINES
When this post is selected a CT icon will appear in the toolbar, this opens CT Expert. A CT
Expert Settings button also will appear on the first page of Wire Strategy Settings.

Charmille Machine, Wire and Part information, also Sequence Definition are displayed by clicking the CT Expert Setting button which opens the form shown below.
Configure CT Expert Interface: Show

or change where the CT Expert Files are kept .

Get data from CT Expert: Get data from CT Expert such as wire type and/or diameter, workpiece material and height and the desired surface finish. Apply these CT Expert settings:

Applies new data from CT Expert to the current application.

51

Use and Reference

CREATING A WIRE EDM PART

When you click on this icon and select a profile, you will be presented with the following options to describe how the part is to be machined.

The first thing you must do is to select a start point. Click on the Select start point button and select a point that represents where the wire is to be threaded, prior to leading into the start of the part. If the shape is closed, then the first element to be machined on the part will be the element you selected when you picked the profile. The lead-in will be created normal to this element, starting at the selected point. If the shape is an open profile, you have the option of starting at the start of the first element in the profile, or starting away from the profile (you will need to select a start point).

T I P

If you choose to start on the profile, then you can add entry/exit moves (to apply/cancel compensation) which will take the form of straight line moves either tangential to the profile, or at 90 degrees. You can also opt to extend the start/end of the end elements. If you select a gluestop, this will always be added at the end of the profile (before any extension is added).

52

Use and Reference

Having selected your start point, you must then specify the gluestop width. This is done in the Gluestop lead in/out dialog, shown below. This opens once a point is selected. You can also enter the diameter of the start hole. This value will be available to the post processor in the event that you would like the approach move split in accordance with this diameter so that you might use different Epak settings for approaching the edge of the hole and approaching the part itself. If you select a circle for the start hole, the circle diameter will automatically be used for the start hole diameter. The start point coordinates are displayed for informational purposes only. These values can only be changed by pressing the Start point button and selecting a new point. Once you press OK you will be returned to the previous form to specify how the part is to be cut. You will see that the form has changed slightly, so that you can modify this start gluestop. The Modify gluestop/lead in button is now enabled, and clicking it will bring back the Gluestop lead in/out dialog to enable you to change either the start position, start hole diameter, or the gluestop width. The Change start element button is also enabled. Clicking here will allow you to select a different element at which to start. This is useful if you picked the wrong element on the profile and would like to start somewhere else on the part. Having selected your start point, it is a good idea to select the Number of cuts. You have the option of selecting between one and eight. Simply click on the required number at the bottom of the form. Note that this number includes the first roughing cut so, for example, four cuts would equal one roughing and three skim cuts. You may also select which specific wire offsets to use simply by checking the appropriate boxes under Select cuts.

53

Use and Reference

Cut type: The Parallel cut option needs no further data. The wire is simply kept vertical to produce parallel walls. Selecting Full height taper requires a Taper angle (in degrees). The part will always be assumed to be larger at the bottom than at the top, so if this is not the case, you will need to enter a negative angle.

You can change the angle of individual elements of a 2-axis tapered part using the Taper icon. This is the fourth item in the left column of the Top Level palette and is described on page 25 and under Modify Taper Angle on page 56. Adding land to a part requires the Land height to be specified. A part with land will be cut once with a roughing offset at the taper angle, then roughed and skimmed with parallel cuts to machine the land.

Near the top right-hand side of this section is a checkbox to indicate if this is to be a 4 axis part; checking this will change your options to include Full 4 axis and 4 axis with land. Regardless of whether you choose Full 4 axis or 4 axis with land, you must select a second profile to represent the bottom of the part. To do this, click on the Select lower profile button and then pick the required profile, making sure that the element you select on the profile is the first element to be machined. If you do not select the correct element, the part will appear twistedthis can be corrected later, but it is better to get it correct now. Having selected the start element on the upper profile, EDM automatically projects an entry line from the start point to the start element and calculates which element on the lower profile this line intersectsthis is the default start point on the lower profile. Once you have selected the lower profile

54

Use and Reference

of a 4-axis shape, click on Select start point on lower profile to select a different element at which to start on the lower profile.

T I P

Using the Select start point on lower profile option, EDM will start at the closest end (to the cursor) of this element. This creates an approach move to the 4-axis part that will twist in two separate directions as it moves towards the shape.

The 4 axis with land option requires a Land height and is treated in similar fashion as 2-axis with land. The 4-axis cuts will be performed once, with a roughing offset, followed by one roughing and all skim cuts parallel to the top profile.

ADD OR EDIT A GLUESTOP

This command enables you to either add another gluestop to a part or to edit an existing one. If you select an element that does not have a gluestop associated with it, you will be able to add a new gluestop. By selecting an element that already has a gluestop associated with it, or by selecting the lead-in to a gluestop, you are able to modify the gluestop definition. You will see when editing a gluestop, you also get the Remove Gluestop button, which allows you to delete a gluestop from a part.

55

Use and Reference

MODIFY TAPER ANGLE

By selecting this icon, you can then select an element or multiple elements of a 2-axis tapered part for which you can modify the taper angles. Select the element you wish to modify to get this form. To modify a single element, enter the value of the New taper angle and click OK. To modify multiple elements, click Select final element and select the element at the other end of the range of elements; the number of selected elements will be indicated in the box underneath this button. Clicking OK will update all the elements in the range with the new taper angle.

Different start and end angles can be specified under the Variable taper tab. Since this can only be applied to one element at a time, the Range of elements option is not provided in this case.

56

Use and Reference

WIRE SYNCHRONIZATION
This icon enables you to add a sync line to a 4-axis part. Sync lines are added between the ends of elements on the two profiles that represent the top and bottom of the part. First, select the element on the top profile, picking near to the end where the synchronization is to occur, then click on the corresponding element on the bottom profile. If you require the wire to remain stopped on one profile, while it continues on the other profile (e.g. stopped on the top and move around a radius on the bottom), then you may add two sync lines to the same element on the profile where the wire is to stop, each of these corresponding to a different element on the other profile. No point may have more than two syncs. When a 4-axis part has the same number of elements on both the upper and lower profiles, you can right-click on the part and be offered the option to automatically synchronize the cut. If you have already added user syncs, then this option will further auto-sync between each pair of user syncs.

NO-CORE CUTTING
After selecting this icon, you will be asked to select either a profile or a circle. If you select a profile, it must be closedyou will then be able to cut all of the area within the profile by using the dialog shown here. Corner loop and Corner Relief is also available. For more information see Corner Loop and Corner Relief: on page 44.

Number of cuts:
You can add optional skim cuts around the profile shape by selecting a number from one to eight in the Number of skim cuts tab. You may also select which specific wire offsets to use under the Selected skim cuts tab.

57

Use and Reference

Overlap:
The Overlap between cuts can be defined either by a percentage of wire diameter or by an actual distance. If you select Percentage of wire diameter and then change the wire diameter in the wire strategy control, the resulting destruction cuts will automatically be re-calculated based on the new wire size. Click on the Start position button to select a start point where the wire will be threaded. If you select a circle for NoCore cutting, then you will be presented with the dialog shown. As for the cutting profile, you can specify the Overlap as either a distance or as a percentage of the wire diameter (automatic recalculation also applies, should you change the wire diameter). The start position will be displayed as the center of the selected circle and the Final diameter is also taken from the selected circle. You can change the Initial diameter to be a value other than zero, in which case the No-Core cutting will start at that specified diameter, rather than at the center of the circle. Checking the CW box will create clockwise arcs, and leaving it unchecked will create counterclockwise cuts.

58

Use and Reference

DIMENSIONING THE PART

This icon offers a palette of icons for dimensioning your part. The top row of icons enables you to dimension a distance. To use any of the first three, you will be asked to select a line; you will then be shown the dimension of that line in either the horizontal (X) axis, the vertical (Y) axis, or the actual dimension parallel to the line. Move the mouse to position the dimension and then left-click to position it. Right-clicking will abandon the dimension. The next three buttons are similar, except you must pick two points and the dimension will be the distance between the points (again, either horizontal, vertical, or parallel). On the bottom row, from left to right, you can dimension a point (the XY position), the angle of one line, the angle between two lines, the radius of an arc and the included angle of an arc. The last icon on the bottom row is used to configure the dimensions. Using this dialog, you will be able to specify the number of decimal places to be used for both linear and angular dimensions and also the height (in inches) of the dimension text.

T I P

The dimension text height is used for all subsequently defined dimensions; existing dimensions will not be changed to reflect this new height.

59

Use and Reference

INFORMATION
This icon offers several methods of obtaining information relating to the part via the following palette of icons. The first two icons provide information on a selected element. Use the first icon to select a construction element (point or circle).

The second icon is for a profile line or arc. Click on the icon and then select the required element and you will be shown information specific to the type of element selected. This may include start/end point, length, and angle.

The third icon is used to measure the distance between two points. After selecting the two points, you will be shown the distance between them relative to the X axis and the Y axis as well as the actual distance between them.

60

Use and Reference

The fourth icon will ask you to select a profile; this will calculate the area and peripheral length around the profile.

The last icon provides a desktop calculator that includes memory/recall and trig functions.

61

Use and Reference

RESEQUENCE THE OPERATIONS

The order in which the machining occurs is determined by the order in which you create wire parts. If you have more than one part, then the first one you create will be machined first. Using this icon enables you to change the machining sequence. You will see a small form that keeps track of the number of parts you pick. Simply click on the part that you want to cut first, followed by the next one and so on until you have selected all the parts. Then click the Finished button and the machining will be resequenced.

T I P

This option only enables parts to be resequenced; it will not affect the order of machining No-Core cuts, which will always be cut in the order in which you define them. Destruction cuts will also occur before cutting any wire parts.

MACHINING SIMULATION
You can see a simulation of the toolpath by clicking on this icon. The form displayed offers a horizontal scroll bar to select the speed of simulation and a Step option to stop the wire at the end of each line or arc. If you select the Step checkbox, then the wire will stop at the end of each element. You will need to click the Step button repeatedly to proceed through the elements.

T I P

Moving the scroll bar to its maximum value will cause the wire to be displayed at the end of each element only. You will not see the wire move along any of the elements when this speed is selected.

62

Use and Reference

CREATING CNC CODE

This icon provides the same toolpath simulation as described above, but CNC code is created as the machining is being simulated. You will see a list of post processors that you have available and also a box containing the file name of the CNC code file. To select a new code filename, simply double-click on the box containing the filename. As the simulation is displayed, you will also see the code being created.

63

Use and Reference

RIGHT-CLICK EDITING
As an alternative to using the icons to modify a part, you can simply point to a line or arc on the screen and perform a right-click. Depending on what type of element you click on, you will be offered a small pull-down menu that provides various options similar to those shown. The menu on the right is shown when you pick a wire part (not a No-Core cycle). The first line is an indication of what type of part has been selected. This will be set to one of three options, Punch, Die or Open Profile. The next option Line: info indicates that the element selected is a line. Selecting this option will show you information about the selected line, including line length, angle, start and end position. The number of cuts and cut length are for informational purposes only. The cut length is the length of a cut around the profile. The Rev prof dir option provides a means of reversing the profile direction; clicking this will reverse the profile and will cause all of the machining to be automatically re-calculated. The context menu for a 4axis profile, on the other hand, will contain Rev upper prof and Rev lower prof as well as Rev both profs. Clicking on the Delete machining option will delete all destruction cuts.
Pattern repeat offers the ability to repeat the selected machining along a path. To apply a pattern, check the box to use pattern and press the select path button, then pick a contour. You will be shown how many repeats will be created as a number on the form press Pam to apply the pattern. To remove the pattern repeat, right-click again and un-check use pattern box and press OK. The path must be a

contour, where the machining will be repeated at each point along the contour (each connector / terminator). The toolpath will be translated so that first wire thread position in the machining will be located at each point on the path. The Properties option at the bottom of the menu provides a method for updating the selected part. If you picked a line that represents a lead-in to a gluestop, then the clicking on Properties will show the form containing the gluestop data. Any other element of the part will show the form containing the part definition data. In either case, you will be able to change the data and update the part.

64

Use and Reference

If you right-click on part of a wire No-Core cycle, you will get a slightly different menu. The first line indicates whether you selected a circle or a profile. The third line provides access to element information. The cut length is the total peripheral length of all the cuts used to destroy the circle /shape. Clicking on the Delete machining option will delete all destruction cuts. Clicking on the Properties option will show the form that was used to create the cycle so that you can change the machining parameters. Right-clicking on a 4-axis sync line provides a menu option to delete the sync line. If you Right Click on a 4-axis line or arc or on a No-Core cycle, you will get the menu shown below. If you have already added user syncs, then this option will further auto-sync between each pair of user syncs. If you right click on any other type of element (a point, a dimension, or a line/arc that has not been used to create a wire part), you will be presented with a menu that simply offers element information (in the case of a dimension, you can also delete the selected dimension). Select the (Element): info option to bring up the Element info dialog as shown.

65

Use and Reference

POST PROCESSING ENHANCEMENTS

A new post processor (drill.pp) has been added to the library of posts. This will create a file containing only XY positions of the wire thread positions to be used to drill the material prior to use on the EDM machine. A new document has been provided to help those wishing to modify or write their own post processors. This will include details on new post processing functionality added to this release:
Simpler commands to format the output, thereby enabling easy switching between inch/metric and absolute/ incremental output. Current single-line IF command enhanced to include IF/THEN blocks and IF/ELSE. The ability to output part profile data (rather than toolpath data) as required by machines such as the Agie Evolution. Added flag in posts to indicate if part is upside-down.

Added new post variables for Part name, Part Filename, Tape Name, and variables for the new datum functionality.

66

Use and Reference

CREATING YOUR OWN POSTS

In the Help menu there is an entry called Posts. This item contains information that will help those wishing to modify or write their own post processors.

This includes details on new Post Processing functionality in the WireEDM module including:
Simpler commands to format the output, thereby enabling easy switching between inch/ metric and absolute/ incremental output. Current single-line IF command enhanced to include IF/THEN blocks and IF/ELSE. The ability to output part profile data (rather than toolpath data) as required by machines such as the Agie Evolution. A flag in posts to indicate if part is upside-down. New post variables for Part name, Part Filename, Tape name and variables for the new datum functionality.

ABOUT CREATING YOUR OWN POSTS

The default EDM posts are installed in the \plugins\edm\posts folder. You will find the plug-ins folder in the same location as your Gibbs EXE file. Each EDM post is a single text file with the extension .pp. Also the posts folder there should also be a similarly named file with the extension .cfg. this file is used by the EDM product and contains machine configuration settings such as travel limits and technology field names. This file must not be edited. When EDM runs, it looks in the \plugins\edm\posts folder and builds a list of all .pp files. This list is displayed, alphabetically, as the list of machines on the wire strategy form.

67

Use and Reference

Before making changes to any post, be sure to always make a backup copy of the post. If this backup is made within the \plugins\edm\posts folder and has the .pp extension it will also appear on the machine list.

If you copy a post to a new name, you should also copy the associated .cfg file. When EDM runs, it will create a .cfg file for post if one does not already exist, but it will use default values for the technology configuration settings which may be different from those used by the post that you have copied.

Post Files: Each post is test file that can be edited using a standard text editor. If a word-processor type editor is used, make sure to save the post as a text file. The post file is not case dependant, although lower-case is generally used. Comments & Variables: Comments may be included by preceding the comment with an exclamation

mark (!). Comments can either be added to the end of a line or a complete line may be a comment. Where a numeric value is to be used, an expression may be used. Your own variables may be also be created to help with calculations. Variable names may be up to 32 characters. Variable names must start with a character (A-Z), can contain the underscore character (_) and numbers (0-9). To avoid conflicts, use names that are not likely to be used in future versions of the software when defining variable names. This can be done by adding a user-specific prefix. For example, instead of offset1, use post1_offset1.

Valid Variable Definitions

x1=10 x2+20 * Cos(45) x3=((x1+2/2)+(x1*x2/2.9)**2)*sin(45)

All variables are treated as floating point numbers. There are several text variables that may be used to create output. You cannot create your own text variables and there are currently no text manipulation functions.

DRILLING
The post processor drill.pp may be found in the library of posts. This will create a file containing only XY positions of the wire thread positions to be used to drill the material prior to use on the EDM machine.

68

TUTORIALS

Tutorials

CHAPTER 3 : Tutori a ls
The Tutorials section of the manual is designed to introduce you to actually working with the GibbsCAM Wire EDM package. There are three tutorials, one covering 2-axis parts, another covering 4-axis parts and the last covering open profile parts. All of the tutorials start with a part file that came with your Wire EDM package. If you are unclear on a topic brought up in the tutorial, please refer to the Reference section of this manual.

TUTORIAL #1 WIRE EDM 2-AXIS

In this tutorial you will become familiar with working with the GibbsCAM Wire EDM interface and creating a simple 2-axis EDM part. You will need to have GibbsCAM and the Wire EDM package installed and licensed.
Launch GibbsCAM. Open the file
die block.vnc.

The file should be located in a folder that was installed along with your Wire EDM package.

71

Tutorials

The part should look like the following image.

Select all of the geometry on the screen (Ctrl-A). Select Launch EDM - Selected Geometry from the Wire EDM menu.

Your Wire EDM screen should look similar to the following image.

Click on the Zoom Full button in the Toolbar to fit the geometry to the screen.

72

Tutorials

The first thing we need to do is to set the wire configuration and strategy.
Click on the Wire Configuration button. It is the top left button in the Top Level palette.

Clicking on the Wire Configuration button will activate the dialog shown below. This dialog is where you will select the type of wire machine you have, wire display, the Z top of the part, part thickness, part orientation and the output for Z planes.
Enter the values as shown.

73

Tutorials

Click on the
Machine strategy

tab.Enter the values shown here.

Clicking on the Machine strategy tab will open this dialog box. Enter the settings shown here. This sets the preferences for how we are going to machine this part.
When you have finished, click OK. Now that we have set up the machine, we can begin to put toolpath on our geometry. Click on the Machining button in the Toolbar.

Looking at the bottom of the screen, we can see that we are being asked to pick the profile to be cut.

Select the area of the middle profile as shown.

74

Tutorials

You now get the Create Wire Part dialog. This dialog allows you to set
Cut type, Start position

and the number of skim cuts. We now need to select a start point for the cut.
In the current dialog click on Select start point.

The bottom of the screen is asking us to select a start point.

Select the point in the middle profile as shown.

You will now see a dialog, as shown below, displaying the coordinates of the start point. We need to set the width of the gluestop.

Enter the value shown here and click on OK.

You will be sent back to the Create Wire Part dialog.

75

Tutorials

Click OK. Click on the Isometric View button in the Toolbar.

Click on the Zoom Full button in the Toolbar.

This will put the part into isometric view and fit the geometry and the toolpath to the screen.The results of your toolpath should look like the image on the right. This is a simple example of how to create a wire path. Now we will go back and modify the toolpath.

Right-click anywhere on the profile to open the right-click menu. Select Properties.

Clicking on Properties opens the Modify Wire Part dialog. This dialog looks similar to the Create Wire Part dialog that we used to generate the toolpath. We will use this dialog to modify the toolpath in order to set a taper and the number of skim cuts.

76

Tutorials

Click on the Full height taper radio button.

This modifies the dialog to include a Taper angle text box and a different graphic.
Enter a taper angle of 5 degrees.

Next we will add some skim cuts.

In the Number of cuts section, click on 4 to set four skim cuts.

Your dialog should look like the image above.

Click on Update.

The dialog should close and the result is an updated toolpath that should look similar to the image shown here. The actual height between each displayed skim cut and the number as well as the color of the dashed 4-axis lines will vary depending on your Display settings found in the Wire strategy/ configuration settings dialog. There is geometry on this part that was not covered in this tutorial. You can use this geometry for continued practice with different machine settings, tapers etc.

77

Tutorials

Save this file in case you would like to go back and work with it at a later date.

78

Tutorials

TUTORIAL #2 WIRE EDM 4-AXIS

In this tutorial you will learn how to create a 4-axis Wire EDM part. Additionally, the lessons learned in the first tutorial will be reinforced through practice.
Launch GibbsCAM. Open the file Four Axis.vnc. The file should be located in a folder that was installed along with your Wire EDM package.

The part should look like the image on the right.

Select all of the geometry on the screen (Ctrl-A).

Select Launch EDM - Selected Geometry from the Wire EDM menu.

79

Tutorials

Your Wire EDM screen should look similar to the following image.
Click on the Zoom Full button in the Toolbar to fit the geometry to the screen.

The first thing we need to do is to set the wire configuration and strategy.
Click on the Wire Configuration button. It is the top left button in the Top Level palette.

Enter the values shown below into the dialog.

80

Tutorials

Click on the Machine strategy tab and enter the settings shown here.

When you have finished, click OK.

Now that we have set up the machine, we can begin to put a toolpath on our geometry.
Click on the Machining button in the Top Level palette.

Looking at the bottom of the screen, we can see that we are being asked to pick the profile to be cut.

81

Tutorials

Select the area of the middle profile as shown.

The Create Wire Part dialog opens, ready for us to select the type of cut we want to make. We now need to select a start point for the cut.
Click on the Select start point button. The bottom of the screen is asking for a start point. Select the point shown. It is the point that is outside of the profiles.

You will now see a dialog displaying the coordinates of the start point. We need to set the width of the gluestop.

82

Tutorials

Enter the value shown below and click OK.

We have been sent back to the Create Wire Part dialog to select the lower profile and the number of cuts to take.
Click on the 4 axis checkbox. Also set the dialog to take four cuts, as shown below. Click on the Select lower profile button.

83

Tutorials

Select the profile as shown to designate the lower profile.

When you select the lower profile, we are sent back to the Create Wire Part dialog to finish setting up the toolpath.
Click OK.

The results of our work should look something like the following image. Looking at the toolpath, we probably have some more work to do, as is often the case with 4-axis parts. We need to synchronize the wire path. In order to sync this toolpath, we need to break some of the elements. To make this easier, we are first going to turn on the Command repeat option.
Click on the Configuration button in the Toolbar to open the Configuration dialog. It is the fifth button from the left.

84

Tutorials

Activate the
Command repeat

function and close the dialog.

The
Command repeat

function allows us to perform the same action multiple times without having to repeatedly open a dialog and select a command.
Click on the Edit /Modify geometry button in the Top Level palette. Click on the Split Element button in the Edit Geometry palette.

The Split element dialog provides several ways to break geometry.

Select the first method Normal to element,
through a point.

Click Select line/arc.

To use the Normal to element, through a point function, we must first select the element we want to split, then we select the point normal to the element. The element will then be split at this point.

85

Tutorials

Split the element as shown here. 1 - Select this element 2 - Select this point Results in a split element

Go through the part and split the elements so your part looks like the one shown here.

86

Tutorials

After splitting the elements your screen should look something like the following image. While the results do look better, the part still needs some work. We need to manually sync some points.
Click on the Sync button in the Top Level palette.

Notice the bottom of the screen is prompting us to pick an element in the top profile that needs a sync point.
Select the points as shown in the following image.

After the point on the top profile is selected, the bottom of the screen prompts you to pick the sync point on the bottom profile. A line attaches your cursor to the top profile and will remain that way until the bottom sync is selected or a right-click is performed.

87

Tutorials

After clicking the two points you will see that the points are now synced. The toolpath looks a little better. We have some more syncs to add however to complete the part.

Add syncs at each of the elements that we split. When you are done, the toolpath should look like the image on the right.

This is better, but the toolpath at the corners is still not optimal. We will not get clean, sharp corners with this toolpath. We will need to add syncs from some of the corners of the top profile to the rounded corners of the bottom profile. Remember each element may have two syncs.

88

Tutorials

Add a sync from the corners to the ends of the rounded corners as shown here.

This is better. The exterior corners are controlled but the toolpath is still not optimal in the interior corners. The way to fix this is to have overlapping syncs from the interior corners.

89

Tutorials

Create a sync from the interior corners to the split elements as shown below.

This results in good toolpath.

90

Tutorials

Switch to isometric view to see the part complete with all of the skim cuts.

Click on the Simulation button to see the rendered part. Be sure to save the part.

91

Tutorials

TUTORIAL #3 WIRE EDM OPEN PROFILE

In this tutorial you will learn how to create a Wire EDM part from open profile geometry. An open profile part is really not that different than a closed profile part, but there are certain things to keep in mind.
Launch GibbsCAM and open the part Open Profile.vnc.

The part should look like the following image.

Select all of the geometry on the screen and transfer the data to the Wire EDM package.

The first thing we need to do is to set the wire configuration and strategy.
Click on the Wire Configuration button. It is the top left button in the Top Level palette.

92

Tutorials

Enter the values shown here.

93

Tutorials

Click on the
Machine strategy

tab and enter the settings shown. When you have finished, click OK. (Click OK again to dismiss the warning message).

We have set up the machine. We can now put a toolpath on our geometry.

Check to ensure that the direction indicators are pointing from the top of the part to the bottom. If arrows are not being drawn on your geometry, change this in the Configuration dialog (accessed from the Toolbar). If the indicators are pointing in the wrong direction see Rev Prof Dir in the Right click menu.
Now click on the Machining button in the Top Level Palette.

Click anywhere on the part.

94

Tutorials

Open profile parts travel in one direction and have a definite starting place, so the element you click on to select a profile to cut does not matter.
Enter information in the Create Wire Part dialog as shown here. When you are ready, click on Select start point.

Select the point that lies above the open profile and click OK in the Gluestop lead in/out dialog. Click on OK in the Create Wire Part dialog to generate the wire toolpath.

95

Tutorials

There is a problem with the toolpath. We selected the Extend End option, which causes the wire to cut into the part. We need to fix this.

Right-click anywhere on the EDM part and select Properties to modify the operation.

96

Tutorials

Turn off Start away from profile and Extend end. Enter a Normal Entry/Exit move of 0.25 as shown here and click on Update to change the operation.

The results of the modified operation look much better with a sufficient lead-in and lead-out. We are now going to make one last modification to this part, which is to add a taper.

97

Tutorials

Right-click on the profile to open the dialog and make the changes shown.

Click on Update to generate the following path.

We will now post process this part.

Click on the Create CNC Code button.

98

Tutorials

Enter a name in the Tape filename box and click GO.

The rendering will run and code will be generated simultaneously.

Save the part when you are done

99

Tutorials

100

INDEX

Index

Index
A
Advanced Settings: 38 Gluestop: 2324 Gluestop Removal: 41

B
Backup: 20

I
Information: 27 Isometric view: 21

C
Chamfer: 26 Change Start Element: 53 Check Travel Limits When Creating Code: 37 Circular dies - Skim cut entry positions: 39 Colors: 20 Command Repeat: 19 Configuration: 19 Create Code: 23, 30 Cut Type: 54

M
Machine: 32 Machine Settings: 35 Machining: 2324 Material: 36 Material Size: 20 Modify Gluestop: 53 Multiple Parts: 42 Multiple Viewports: 2021

D
Dimensions: 19, 26 Dir indicators: 19 Display Settings: 46 Distance Between Skim Cuts: 46 Dynamic Rotation: 21

N
No Core Cutting: 23 No-Core Circles - Skim cut entry positions: 38 No-Core Cutting: 26

O
Operations Sheet: 23, 28 Output Z Planes: 37 Overlap: 58

F
Fillet: 26 Front: 20

P G
Part Orientation: 37 Parts with Land: 44 Plan: 20
103

Geometry: 23, 26

Index

Plug-Ins Menu: 5 Profile start: 19

Wire Guides: 36 Wire Strategy: 23

R
Radius: 23, 25 Rapid moves: 19 Redo: 21 Redraw: 18 Remove Gluestop: 55 Retract Distance: 4041 Rough cut entry moves: 38 Z Height: 36 Zoom Full: 18 Zoom In: 18 Zoom Out: 18

S
Sequence: 23, 27 Set Feedrates: 34 Side: 20 Simulation: 29 Skim Cut Direction: 40 Skim Cut Transition: 41 Split Element: 19, 26 Start Position: 58 Sync: 23, 26

T
Taper: 23, 25 Technology Settings: 33

U
Undo: 2022

W
Wire can be threaded at an angle: 36 Wire Diameter: 36
104