b-

Designation: E 595 - 93

AMERICAN SOCIETY FOR TESTING AND MATERIALS 100 Barr Harbor Dr.. West Conshohocken, PA 19428 Reprinted from the Annual Book of ASTM Standards. Copyright ASTM If not listed in the current combined index, will appear in the next edition.

Standard Test Method for Total Mass Loss and Collected Volatile Condensable

Materials from Outgassing in a Vacuum Environment

This standard is issued under the fixed designation E 595; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (f) indicates an editorial change since the last revision or reapproval.

Standardrfor rhe specijic year o/issue which has been adopted by the Depanmenl of Defense.

This test method has been approved for use by agencies of the Department of Defense. Consult the DOD Index

of Specifications and

1. Scope 1.1 This test method covers a screening technique to determine volatile content of materials when exposed to a vacuum environment. Two parameters are measured: total mass loss (TML) and collected volatile condensable materials (CVCM). An additional parameter, the amount of water vapor regained (WVR), can also be obtained after completion of exposures and measurements required for TML and CVCM. 1.2 This test method describes the test apparatus and related operating procedures for evaluating the mass loss of materials being subjected to 125C at less than 7 x low3 Pa (5 x 10e5 torr) for 24 h. The overall mass loss can be classified into noncondensables and condensables. The latter are characterized herein as being capable of condensing on a collector at a temperature of 25C.
N OTE I-Unless otherwise noted, the tolerance on 25C and 12X is f 1C and on 23C is +2C. The tolerance on relative humidity is k5 %.

sqfety problems associated with its use. It is the responsibility

1.7 This standard does not purport to address all of the

of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 2. Referenced Document 2.1 ASTM Standard: E 177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods2 2.2 Adjunct: Micro VCM Detailed Drawings3 3, Terminology 3.1 Definitions: 3.1.1 collected volatile condensable material, CVCM-the quantity of outgassed matter from a test specimen that condenses on a collector maintained at a specific constant temperature for a specified time. CVCM is expressed as a percentage of the initial specimen mass and is calculated from the condensate mass determined from the difference in mass of the collector plate before and after the test. 3.1.2 total mass loss, TML-total mass of material outgassed from a specimen that is maintained at a specified constant temperature and operating pressure for a specified time. TML is calculated from the mass of the specimen as measured before and after the test and is expressed as a percentage of the initial specimen mass. 3.1.3 water vapor regained, WI&the mass of the water vapor regained by the specimen after the optional reconditioning step. WVR is calculated from the differences in the specimen mass determined after the test for TML and CVCM and again after exposure to a 50 % relative humidity atmosphere at 23C for 24 h. WVR is expressed as a percentage of the initial specimen mass. 4. Summary of Test Method 4.1 This microvolatile condensable system4 was developed from an earlier system for determination of macrovolatile condensables that required much larger samples and a longer test. 2 Annual Book of ASTM Standards, Vol 14.02.

1.3 Many types of organic, polymeric, and inorganic materials can be tested. These include polymer potting compounds, foams, elastomers, films, tapes, insulations, shrink tubings, adhesives, coatings, fabrics, tie cords, and lubricants. The materials may be tested in the as-received condition or prepared for test by various curing specifications. 1.4 This test method is primarily a screening technique for materials and is not necessarily valid for computing actual contamination on a system or component because of differences in configuration, temperatures, and material processing. 1.5 The criteria used for the acceptance and rejection of materials shall be determined by the user and based upon specific component and system requirements. Historically, TML of 1 .OO % and CVCM of 0.10 % have been used as screening levels for rejection of spacecraft materials. 1.6 The use of materials that are deemed acceptable in accordance with this test method does not ensure that the system or component will remain uncontaminated. Therefore, subsequent functional, developmental, and qualification tests should be used, as necessary, to ensure that the materials performance is satisfactory.
I This test method is under the jurisdiction of ASTM Committee E-2 I on Space Simulation and Applications of Space Technology and is the direct responsibility of Subcommittee E2 I .05 on Contamination. Current edition approved June 15, 1993. Published August 1993. Originally published as E 595 - 77. Last previous edition E 595 - 90.
1

3 Available from ASTM Headquarters. Order PCN 12-505950-00. 4 Muraca, R. F., and Whittick, J. S., Polymers for Spacecraft Applications. SRI Project ASD-5046, NASA CR-89557, N67-40270, Stanford Research Institute, September, 1967.

TABLE Letter AA B4 CA DA= EA.= p. c Gc HA JA K L M N P Q : T u v

w

Test Apparatus in. 0.250 0.438 1.300 0.531 0.380 0.026 0.50 0.030 0.500 l/,~
7A o

Dimensions (See Fig. 2) Tolerance *0.005 *0.005 *0.005 *0.005 *0.005 *0.005 *0.01 *0.05 *0.01 o
*1/= *l/&

mm 6.3 11.1 33.0 13.45 9.65 0.65 7.1 0.75 12.7 1.6 8.0 16.0 16,0 32.0 50.0 25.5 0.4 12.0 25.5 25.5 50.0 6.0 25.0 1.6

Toleranca *0. I *0.1 *0.1 *O.1O *O.1O *O.1O *0.3 *0,10 *0.3 kO.8 &O.8 *0.1 kO.8 *0.8 *0.8 &O.8 20.3 *0.8 *0.8 &O.8 &O.8 &O.8 AO.8 kO.8

Notes diameters diameterB diameterB

stook size

0.625 % 11/, 2 :.015 1/2 1 1 2 1/4 1 l/,@

*0.005 *l/* *l/* *l& *1/= *0.01 o

*1/=

cover plate must fit snugly

hatf stock thickness

*1/=
*1/~

x Y z

*1/~ *1/= *1/~

*1/=

radius, twicel

A Critical dimensions that must be maintained for test results to be comparable. S Diameters must be concentric to *0. I mm (*0.005 in.) for test results to be comparable. c ~Msh ~~ ~UW ~w=. SatisfUtW ~a~s have been produoed by making substrate surfaoe finish, 1.6 pm RMS (63 pin. plated with eiactroiess nicket, 0.0127-mm (0.0005-in.) thick, and fin&hed with electroplated chromium, 00051-mm (0.0002-in.) thiok,

RW), higW po~sh~t

4.2 The test specimen is exposed to 23C and 50 % relative humidity for 24 h in a preformed, degreasedcontainer (boat) that has been weighed.After this exposure,the boat and specimen are weighed and put in one of the specimen compartments in a copper heating-bar that is part of the test apparatus. The copper heating-bar can accommodate a number of specimens for simultaneous testing. The vacuum chamber in which the heating bar and other parts of the test apparatus are placed is then sealed and evacuated to a vacuum of at least 7 x 10-3Pa (5 x 10-5torr). The heating bar is used to raise the specimen compartment temperature to 125C. This causes vapor from the heated specimen to stream from the hole in the specimen compartment. A portion of the vapor passesinto a collectorchamber in which some vapor condenseson a previously-weighedand independently temperature-controlled, chromium-plated collector plate that is maintained at 25C, Each specimen compartment has a corresponding collector chamber that is isolated from the others by a compartmented separator plate to prevent cross contamination. After 24 h, the test apparatus is cooled and the vacuum chamber is repressurizedwith a dry, inert gas. The specimen and the collector plates are weighed. From these results and the specimen mass determined prior to the vacuum exposure, the percentage TML and percentage CVCM are obtained. Normally, the reported values are an average of the percentages obtained from three samples of the same material.
NOTE 2It is also possible to conduct infrared and other analytical tests on the condensate in conjunction with mass-loss tests. Sodium chloride flats may be used for infka.red analysis. These flats are nominally 24 mm (1 in.) in diameter by 3.2-mm (O.125-in.) thick, and are supported edgewisein a metal holder that fits into the collector plate receptacle. On completion of the test, the flats are placed into an infrared salt flat holder for examination by an infmed spectrophotometer. As an alternative method, the condensate may be dissolved from the metallic collector, the solvent evaporated, and the

residue deposited on a salt flat for infrared tests. Sodium chloride flats shall not be used for CVCM determinations.

4.3 After the specimen has been weighedto determine the TML, the WVR can be determined, if desired,as follows:the specimen is stored for 24 h at 23C and 50 % relative humidity to permit sorption of water vapor. The specimen mass after this exposure is determined, From these results and the specimen mass determined after vacuum exposure, the percentage WVR is obtained. 4.4 Two or three empty specimen chambers in the heater bar and collector plates on the cold bar, selectedfor each test at random, can be used as controls to ensure that uniform cleaning procedures have been followedafter each test. 4.5 A typical test apparatus can have 24 specimen chambers with 24 associated collector plates so that a number of specimens of Merent types can be tested each time the foregoing operations are conducted. Three specimen compartments can serve as controls and three can be used for each type of material being tested. The total time required for specimens requiring no prior preparation is approximately 4 &ys. The equipment should be calibrated at least once a year by using previously tested materials as test specimens. 4.6 The apparatus may be oriented in any direction as long as the configuration shown in Fig. 1 is maintained and bulk material does not faU from the sample holder nor obstruct the gas-exit hole. The dimensions for critical components given in Fig. 2 and Table i are provided so that apparatus constructed for the purpose of this test may provide uniform and comparable results. 5. Signifkance and Use 5.1 This test method evaluates, under carefullycontrolled conditions, the changes in the mass of a test specimen on exposure under vacuum to a temperature of 125Cand the 9

595 absorption of water vapor while exposed to an uncontrolled humidity environment. While control of humidity is not necessary at this point, the temperature for the weighing should be controlled at 23C, the same temperature prescribed for the 24-h storage test. 6. Apparatus 6.1 The apparatus used in the determination of TML and CVCM typically contains two resistance-heatedcopper bars. Generally, each bar is 650 mm (25.5 in.) in length with a 25-mm (l-in.) square cross section, and contains 12 specimen chambers. The open section of each specimen chamber allows vapors from the specimen to pass through a hole into a collector chamber where it impinges on a removable chromium-plated collector plate maintained at 25C throughout the test. (See Figs. 1 and 2.) Variations in test apparatus configurations are acceptableif critical dimensions are maintained as prescribed in Table 1. 6.2 Typically,a total of 24 specimen chambers is used for testing during a 24-h vacuum operation; three of the chambers are maintained as controls. The test apparatus can be mounted on the base plate of a vacuum system within a narrow vacuum bell, 260 mm (10Ydin.) in diameter, that rests on a specially adapted feed-through collar, also supported by the base plate. 6.3 The operation of the vacuum chamber system and any device for raising the vacuum bell can be automatically controlled. Power to the heating element mounted in the copper bars is generally controlled by variable transformers through temperature controllers. Recorders with an electronic icepoint referencejunction feedback may be used to monitor the heater bar temperatures. A heat exchangerusing a suitable fluid maybe used to maintain the collectorplate at 25C during the test.4 6.4 It is recommended that the vacuum chamber system include automatic controls to prevent damagein the event of power failure or cooling fluid supply failure when in unattended operation. Care must be taken to prevent backstreaming of oil from vacuum or diffusion pumps into the vacuum chamber. 6.5 The controller thermocouple should be mechanically attached to the heater bar or ring to prevent the thermocouple from loosening over time. It is essential that the orifice of the sample heater and collector plate be aligned and checked regularly.A good test of alignment and stability is to run the same material in every sample chamber. The results should agree within the accuracy of the test per Section 11. 7. Test Specimen 7.1 Finished products (for example,elastomers,hardware, and structural parts) are cut into small pieceson the order of 1.5 to 3.()-mm (1/16 to l/i-in.) cubes to fit into the specimen boat. Boats approximately 10by 6 by 12 mm (3/8 by 1Aby % in.) have been found satisfactory.
7,2

SEPARATOR FIG. 1

PLATE

Schematic of Critical Potion of Test Apparatus (Section A-A of Figure 2)

massof those products that leavethe specimenand condense on a collectorat a temperature of 25C. 5.2 Comparisons of material outgassing properties are valid at 125C sample temperature and 25C collector temperature only. Samples tested at other temperatures may be compared only with other materials which were tested at that same temperature. 5.3 The measurements of the collected volatile condensable material are also comparable and valid only for similar collectorgeometry and surfacesat 25eC.Samples have been tested at sample temperatures from 5(YCto 230C, and at collector temperatures from 1C to 3(YCby this test technique. Data taken at non-standard conditions must be clearlyidentified and should not be compared with samples tested at 125C sample temperature and 25C collector temperature. 5.4 The simulation of the vacuum of space in this test method does not require that the pressure be as low as that encountered in interplanetary flight (for example, 10-12Pa (10-4 torr)). It is sutlicient that the pressure be low enough that the mean free path of gas molecules be long in comparison to chamber dimensions. 5.5 This method of screening materials is considered a conservativeone. It is possiblethat a fewmaterials will have acceptable properties at the intended use temperature but will be eliminated because their properties are not satisfactory at the test temperature of 125C.Also, materials that condense only below 25C are not detected. The user may designate additional tests to quali~ materials for a specific application. 5.6 The determinations of TML and WVR are tiected by the capacity of the material to gain or lose water vapor. Therefore, the weighingsmust be accomplished under controlled conditions of 23C and 50 % relative humidity, 5.7 Alternatively, all specimens may be put into open glassvials during the 24-h temperature and humidity conditioning. The vials must be capped prior to removal from the conditioning chamber. Each specimen must be weighed within 2 min after opening the vial to minimize the loss or
3

Products

that

require

compounding

are

normally

mixed in 10-g batches to ensure representative samples. Materials shall be cured as sheets, thin slabs, or thicker sections to simulate application in actual use; then they shall be sectioned in accordancewith the foregoingdimensions for specimen cubes.

P%N-i

NJ

\ x

+ -s H

R-

I I 4 *H A -~-- 1.
--s

. ---

?#

~---:--T 2 ,. -

-.

tl

I
I
I

FIG. 2

Critiod Portion of Test Apparatus (See Table 1 for Dimensions)

7.3 Adhesive tapes shall be applied to a surface,such as a preweighed aluminum ring or foil, to simulate actual use. Paints can be applied to aluminum foil by brushing, dipping, or spraying to approximate the as-usedthickness, then cured before testing. A paint can also be cured on an inert surface such as TFE-fluorocarbon, removed as a film, and treated as bulk material. Some adhesivesor sealants maybe applied to preweighedaluminum foil and cured.
4

7.4 Greases shall be placed into a boat. Liquids shall be placed directly in a boat or absorbed in an ignited neutral ftier such as asbestosor silica and then placed in a boat. The technique used shall be stated in the report. Liquids and greases, especially silicones, are prone to creep; if the material exhibits creep to such an extent that some flowsout of the boat, the test results shall be disregarded. 7.5 Minimum specimen massesin the order of 200 mg are

I I ;

required, If smaller quantities are utilized, the accuracy of the measurements may be impaired. 7.6 It is absolutely essential that specimen materials not be contaminated at any step in the specimen fabrication process, Most importantly, specimen material shall not be handled with the bare hands as oils from human skin are volatile and condensable and thus will cause falseTML and CVCM results. 7.7 The following specimen handling procedures are recommended to control contamination: 7.7.1 Wear suitable gloves or finger cots during all specimen preparation steps. 7.7.2 All previously prepared materials can be assumed to be contaminated in the as-receivedcondition; and must be cleaned. 7.7.3 Use cleaning solvents that are known to be nonreactive with the specimen material and that are known to leave no residue. 7.7.4 When possible,discard exterior surfacesof materials when preparing specimens. A clean razor blade can be used to shave off exterior surfaces of rubbers, foams, and other soft materials. Exterior surfaces of harder materials can be removed with a clean jewelers saw. A clean jewelersdrill can be used to remove specimen material from the center part of material suspected of being contaminated. 8. Procedure 8.1 Weigh a prepared aluminum foil boat and return it to its storage beaker in a glass desiccator utilizing silica gel desiccant. 8.2 Weigh a prepared collector and mount it into its cooling-platereceptacle. 8.3 Add the test specimen (100 to 300 mg) to the boat and condition the sample at 50 % relative humidity and 23Cfor a minimum of 24 h. 8.4 Weigh the conditioned specimen (see 4.6) using a balance having *1 pg sensitivity. 8.5 Place the specimen and boat into a specimen compartment of the heating bar in the microvolatilecondensable system.4
NOTE2Prior to the operation noted in 8.5, the copper compartment bar, separator, and cooling plate shall be clean, in position, and awaiting the specimen boats and collector plates.

8.11 Maintain the heater bar temperature at 125C (or other nonstandard temperature) for 24 h, then close the high vacuum valveto the pumping system and turn off the heater bar current. 8.12 Open the vent valve and backfill with clean, dry nitrogen regulatedwithin a gagepressure range from 10to 30 kpa (2 to 4 psi) above atmosphere to cool the bars rapidly. 8.13 Allow the heater bar to cool su~ciently to permit handling (nominally 2 h to reach 50C). Then turn off the collector-plateheat exchangers,return the vacuum chamber to room pressureusing the clean, dry nitrogen, and open the chamber. 8.14 Store aluminum boats with specimens and respective collector plates in desiccators (using active silica gel desiccant) immediately. After specimens have cooled to approximately room temperature, but no longer than % h, remove and weigh each specimen within 2 min of its removal from the desiccators. Control collector plates are used to detect cross contamination or poor technique. Mass loss of greater than 20 p.gby a control is usually due to poor preparation and cleaningof the collector plate. Mass gain of greater than 50 pg is an indication of poor cleaning, poor bake-out of the heater assembly, cross contamination, or poor vacuum technique. Any change of 50 ~g (0.05 % of a 100-mgcontrol mass) or greater is reason for concern and for a review of or change in techniques. All data acquired during runs when this occurs shall be discarded or retained with a note indicating the discrepancy. 8.15 Return the foregoing samples to the relative humidity chamber for 24 h if the WVR is to be determined. Weigh the conditioned specimens (see 5.6).
NOTE3Annex Al contains recommended cleaning and storage procedures.

9. Calculation 9.1 Calculate TML as follows:

Initial Mass, g Specimenand boat Boat Specimenalone Differenceor mass loss Specimenon aluminum foil and boat Aluminum foil and boat Specimenalone Differenceor mass10ss S1+ B, B1 (S, + B,)B,= S1 L= S,-SF L/S, X 100=% S1+ A!l + B! Al, + B1 (S, + Al, + B,) (Al, + B,)= S, L=S,-SF L/S, X 100= % TML Final Mass,g SF+ B, B, (SF+ B,) B,= SF TML SF+ Al, + B, Al, + B, (SF+ Al, + B,) (Al, + B,)= SF

8.6 Mount and screw down the respective cover plates

~% / 1 1 ;

onto the entry end of each specimen compartment. 8.7 Close the vacuum system and evacuate it to 7 x 10-3 Pa (5 x 10-5 torr) or less within 1 h, using proper operating procedures. 8.8 Control of the collector plate temperature at 25C (or other temperature if a non-standard testis being conducted) shall be achieved within the first hour of pump-down. 8.9 When a pressure of 7 x 10-3 Pa (5 X 10-s torr) is reached, turn on the heater bar and adjust the variable transformers to raise the heater bar temperature to 125C(or other nonstandard test temperature) within 60 min. If the sample temperature will exceed 15(YC,up to 2 h may be required to reach temperature. Temperature controllers should maintain bar temperatures at 125*C(or other desired temperature). 8.10 Maintain the collector plate temperatures at 25C(or other nonstandard temperature). 5

9.1.1 A correction maybe made using control boats when

calculating TML. This correction is recommended but not required unless an excessivemass change occurs as described in 8.14. 9.2 Calculate CVCM as follows:
~ ~loo=%cvcM

()s~ where: CO = mass of condensable, g = CF- C,, c* = initial mass of collector plate, g,

(1)

!~

E 595 three values for each material and the averagevalue), 10.1.11 Percentage of water vapor regained, WVR (normally three values for each material and the averagevalue),if determined, 10.1,12 Initial mass of the dried collector plates, Cl, 10.1.13 Change in mass of the control collector plate, C~, in grams, 10.1.14 Final mass of the collectors, Cm 10.1.15 Percentage of collected volatile condensable material, CVCM (normally three values for each material and the average value), 10.1.16 Infrared spectrum or other analytical description of the condensed contamination when determined, and 10.1.16 Remarks about any noticeable incident or deviation from standard conditions observed during the test,
11. Precision and Bias

s, = initial specimen mass, g.

CF = final mass of collector plate and condensable, g, and

9.2.1 A correction may be made using control collector plates when calculating CVCM. This correction is recommended but not required unless an excessivemass change occurs as described in 8.14.

c~= C&- cc,

where:

(2)

c~ = change in mass of control collector plate, g

CC~= final mass of control collector plate, g, and c~~= initial mass of control collector plate, g. 9.3 Calculate WVR as follows: St-s

s~
where:

x1

OO=%WVR

(3)

SF = reconditioned mass of specimen and boat after 24 h at

50% relative humidity, g, and SF = final specimen mass, g. 9.4 Calibrate the balance periodically (at least every 6 months) and apply the appropriate calibration factors.
10. Report

10.1 Report the followinginformation: 10.1.1 Trade name and number of the material, the manufacturer, the batch or lot number, or other such identification, 10.1.2 Summary of the preparation schedule (mixing proportions, cure time and temperature, post-cure, cleaning procedures), date prepared, 10.1.3 Number of samples (nominally three for each material, but many organizations use only two samples per test), 10.1.4 Samples configuration (size,shape, etc.). Statement of technique used in handling liquids or greases(see 7.4), 10.1.5 Statement of sample test temperature (125C), collector plate temperature (25C),and duration of test and dates of test, 10.1.6 If nonstandard sample or collector temperatures are used, clearly mark the test report NONSTANDARD CONDITIONS, and note the actual test temperature, 10.1.7 Initial mass of conditioned samples, S1, 10.1.8 Mass of samples as taken from test chamber, SF, 10.1.9 Final mass of samplesafler optional reconditioning for 24 h at 50% relative humidity and 23C, SF, if WVR determination is conducted, 10.1.10 Percentage of total mass loss, TML (normally

11.1 Precision of these measurements was established by interlaboratory tests of 7 materials by 13 organizations. Precision for particular materials is affectedby the nature of the material as well as testing variance. For example, monolithic, homogeneous materials with relativelylow TML and CVCM values will have high precision and low standard deviation, Materials that are mixed and cured individually before testing may not, be homogeneous or completely comparable from organization to organization. Despite such possible variations, the test can successfullyidentifi good and bad lots of materials, and screen out relatively low outgassing materials from relatively high outgassing materials. For example, DC340 grease was tested and found to have an averageTML value of 0.0867 %* 0.03459 % for the 15 organizations. Polyethylene beads had an average TML value of 0.38495 * .0047 % for the 15 organizations, and an averageVCM of 0.1441 k .0039 %. The same polyethylene beads were tested twice previously. TML values were 0.37986 * .0077 % and 0.3649* .0375 %. VCM valueswere 0.1253 * .01317 % and 0.1415 * .038 %. Precision for this test method is *10 % (95 % confidence level) for TML and *2O % for CVCM. 11.2 Bias for this test method has not been determined. 11.3 Precision of H is influenced greatlyby whether or not the material is hydrophilic. For example, CV2566 siliconeW/R was measured by 15 organizations as 0.01921 * .00313 %, or a 3 sigma uncertainty of 48.8 %. G569 glass tape had WVR of 0.09368 * .01314 %, or a 3 sigma uncertainty of 42.1 %. A reasonable approximation is 40 to 50% uncertainty in WVR for most materials with low WvR.
,

ANNEX Al. CLEANING AND STORAGE Al.1 Cleaning

A1.1.1 GeneralThe components shall be cleaned after fabrication to remove any residual oils, etc., from the fabrication process. The cleaning operations in Al. 1.2 through A1.1.9 shall be performed before each test run unless otherwise specified. 6

A1.1.2 Aluminum BoatsVapor degreasethe boats for 5 or more min. A 1:1:1by volume chloroforrn:acetone:ethanol solvent blend has been used successfully for this purpose. Dry the boats at 125 * 5C for at least 4 h. Al. 1.3 Collector PlatesImmerse and agitate collector plates in the solvent. Follow this with vapor-degreasingfor

em E 595
blend has been used successfully for this purpose. A 1.19 Cleaning Materials-All wiping materials and swabs shall be preextracted using solvents with which they will be used. (See Note Al .) All solvents shall be of spectra-grade or equivalent purity. The nitrogen gas shall be 99.9 % pure, or better, and shall have a dew point of -60C (-76F) or less. The gas shall be faltered using a Molecular Sieve 5A or equivalent. Metal tubing (for example, stainless steel or copper) that is used for gas transfer shall be cleaned before use.
N OTE AI-A recommended extraction procedure for cleaning wiping material is a 24-h treatment in a Soxhlet extractor charged with a mixture of 90 % chloroform: 10 % ethyl alcohol.

15 min. A 1: 1: 1 by volume chloroform:acetone:ethanol solvent blend has been used successfully for this purpose. Dry the collectors for 4 h minimum at 125 f 5-C. Al. 1.4 Specimen Chamber and Heating Bar-Take special care with the bar between test runs to avoid contamination during subsequent tests. Wash the bar cavities and surface with a suitable solvent. A 1:l by volume acetone:ethanol solvent blend has been used successfully for this purpose. Mount the bar into the system without specimens. Evacuate the system to 1 x 10m4 Pa ( 1 X 10m6 torr) and degas the bar at 150 f 5C for 4 h minimum. This is 25C above the normal test temperature. Then turn off the heater to the bar and allow the bar to cool under vacuum. Leave the heater chamber bar in place in the vacuum system. It need only by removed after the test for recleaning. The vacuum system can be configured to close off the belI volume, if necessary, thus permitting the vacuum-pumping system to be off over a weekend. A 1.1.5 Separator Plate-Wash the separator plate with a suitable solvent. A 1: 1 by volume acetone:ethanol solvent blend has been used successfully for this purpose. Use filtered dry nitrogen gas to remove particulates and to evaporate solvents. A 1.1.6 Collector Plate Support-Following the system degassing described in Al. 1.4, wipe the collector plate support using a suitable solvent. Ethanol has been used successfully for this purpose. A 1.1.7 Vacuum Bell-Poor vacuum is frequently caused by material outgassing from the internal bell surface. Wipe down the bell interior with a suitable solvent as required to restore vacuum-operating efficiency. Ethanol has been used successfully for this purpose. A 1.1.8 Other Items-Various other items such as brackets and standoffs can be cleaned as required by wiping with a suitable solvent. A 1: 1 by volume acetone:ethanol solvent

Al .2 Storage A 1.2.1 Boats-AAer cleaning, the boats can be placed in 5-cm3 beakers with designated compartment numbers, then stored in a desiccator that contains indicating silica gel. Seal the unit with a low-vapor pressure grease for ground glass joints. The boats shall be weighed within one day of being stored. A 1.2.2 Collector Plates-The plates can be mounted on a circular plate rack and stored in a desiccator that contains indicating silica gel. Seal the unit with a low-vapor pressure grease for ground glass joints. Plates shall be weighed within 1 day of being stored. Al .2.3 Handling and Storage-Due to the nature of this method, it is imperative that good cleaning procedures be followed to minimize handling of cleaned parts and the introduction of contaminants after cleaning. Hence, all components that have been cleaned must be stored in such a manner as to maintain their clean state. A 1.2.4 Vacuum System-Perform periodic maintenance in accordance with the manufacturers recommended practices in order to ensure good vacuum system performance.

APPENDIX (Nomnandatory Information) Xl. TEST REPORTING FORM

X1.1 The followingformat is suggestedfor reporting raw data and test results.
OWGASSING Material:(name,part number,bt, etc.) DescdptiOm (matedsl type, sampleJ form, cchr, etc.) Conditim (mix and oure, pm w poet oonditbn, as received, on substrate, etc.) Telephon& . DATA SHEET

Manufacture Requesw. Date: Blanks: Heater position

No.

LooatiOm Charge No.:

( ) ( )( )

initialholdermass, g F@ holder mass, g

InitialOoilectwmass, g Flnatcollectormass, g sample: Heater Position No. Initial hOider mass, g Mid holder PIUS sample

)(

)(

Final holder plus sample Reweighed sample pfus holder, 24 h 50 % RI+, gA Initial colleotor mass, g Final Oot!ector
mSSS, g

Total mass bss (TML) % Ave. % TML Total mass gain (CVCM) % Ave. % CVCM Total water regained~ Ave. % WVR (Sample WVR) A ~R measurement h OptiOnd Remarks (Sample appearance, @actor Date test begun: C. Sample temperature,

appearance

after test, any test anomalies, non-standard oondltions, problems, etc)

Coflector temperature, C: Datetest completed:

Pressure tom Time at test temperature hours:

Operator signature:

The American Society for Testing and Materials takes no position respechng the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision af any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shoufd make your views known to the ASTM Committee on Standards, 100 Barr Hzrbor Drive, West Conshohocken, PA 19428.