Lashing System

On Site Examination & Lifting Equipment Specialists
Ratchet Lashings
Full details and safety information about our range of Polyester Ratchet Lashings Download as PDF
Applications
Polyester Webbing Slings, Polyester Round Slings and Ratchet Lashings are used for lifting loads or securing objects that may have fragile or delicate surfaces , which could be harmed if lifted with chains or wire ropes .
Range
offers a wide range of Webbing And Round Slings from WLL 1 tonne to 20 tonne as standard, with special slings being manufactured up to WLL 100 tonne . Specially designed and much larger capacity Round slings up to WLL 800 tonne can be produced upon request. Ratchet Lashings can be supplied from 800kgs to 10 tonne MBL (10,000 daN). Special lashing assemblies can be manufactured upon request.
Design
Webbing Slings in accordance with BS EN1492 are manufactured from synthetic polyester material and are woven using the same core materials. Round Slings in accordance with BS EN 1492 are also produced from the same polyester core materials. Ratchet Lashings in accordance with EN12195-2 are produced from the same polyester core materials Each sling is marked with : 1. WLL and effective working length 2. relevant standard applicable e.g. BS EN 1492, EN12195, BS5759 3. Individual identification or traceability mark 4. Manufacturers name or symbol e.g.Lift King, 5. CE Lashking
Finish
webbing and Round Slings supplied in accordance with BS EN 1492 are colour coded to reflect the WLL. ratchet lashings are supplied in accordance with BS EN 12195 and can be produced in various colours to suit customer requirements.
Certification
All Webbing and Round Slings and Ratchet Lashings can be supplied with an EC Declaration of Conformity and /or manufacturers works certificate.
Instructions for use

In selecting and using web lashings, consideration shall be given to the required lashing capacity, taking into account the mode of use and the nature of the load to be secure. The size, shape and weight of the load, together with the intended method of use, transport environment and the nature of the load will affect the correct selection. For stability reasons free-standing units of load have to be secured with a minimum of one pair of web lashings for frictional lashing and two pairs of web lashing for diagonal lashing. The selected web lashings shall both be strong enough and of the correct length for the mode of use. Basic lashing rules: 1. Plan the fitting and removal operations of lashing before starting a journey. 2. Keep in mind that during journeys parts of the load may have to be unloaded. 3. Calculate the number of web lashings according to EN 12195-1 4. Only those web lashings designed for frictional lashing with STF on the label are to be used for frictional lashing; 5. Check the tension force periodically, especially shortly after starting the journey. Because of different behaviour and elongation under load conditions, different lashing equipment (e.g. lashing chain and web lashings) shall not be used to lash the same load. Consideration shall also be given to ancillary fittings (components) and lashing devices in the load restraint assembly are compatible with the web lashing. During use flat hooks shall engage over the complete width of the bearing surface of the hook. Release of the web lashing: Care should be taken to ensure that the stability of the load is independent of the lashing equipment and that the release of the web lashing shall not cause the load to fall off the vehicle, thus endangering the personnel. If necessary attach lifting equipment for further transport to the load before releasing the tensioning device in order to prevent accidental falling and/or tilting of the load. This applies as well when using tensioning devices which allow controlled removal. Before attempting to unload a unit of load its web lashings shall be released so that it can be lifted freely from the load platform. During loading and unloading attention has to be paid to proximity of any low overhead power lines. The materials from which web lashings are manufactured have a selective resistance to chemical attack. Seek the advice of the manufacturer or supplier if exposure to chemicals is anticipated. It should be noted that the effects of chemicals may increase with rising temperature. The resistance of man-made fibres to chemicals is summarised below. Polyamides are virtually immune to the effects of alkalis. However, they are attacked by mineral acids.
Polyester is resistant to mineral acids but is attacked by alkalis. Polypropylene is little affected by acids and alkalis and is suitable for applications where high resistance to chemicals (other than certain organic solvents) is required. Solutions of acids or alkalis which are harmless may become sufficiently concentrated by evaporation to cause damage. Take contaminated webbings out of service at once, thoroughly soak them in cold water, and dry naturally. Web lashings complying with this Part of EN 12195 are suitable for use in the following temperature ranges: 1. 40C to +80C for polypropylene (PP); 2. 40C to +100C for polyamide (PA); 3. 40C to +120C for polyester (PES); These ranges may vary in a chemical environment. In that case the advice of the manufacturer or supplier shall be sought. Changing the environment temperature during transport may affect the forces in the web lashing. Check the tension force after entering warm areas. Web lashings shall be rejected or returned to the manufacturer for repair if they show any signs of damage. The following criteria are considered to be signs of damage; 1. Only web lashings bearing identifications labels shall be repaired; 2. If there is any accidental contact with chemical products, a web lashing shall be removed from service and the manufacturer or supplier shall be consulted; 3. for web lashings (to be rejected): tears, cuts, nicks and breaks in load bearing fibres and retaining stitches; deformations resulting from exposure to heat; 4. for end fittings and tensioning devices: deformations, splits, pronounced signs of wear, signs of corrosion. Care should be taken that the web lashing is not damaged by the sharp edges of the load on which it is used. A visual inspection before and after each use is recommended. Only legibly marked and labelled web lashings shall be used. Web lashings shall not be overloaded: only the maximum hand force of 500 N (50 daN on the label; 1daN = 1 kg) shall be applied. Mechanical aids such as levers, bars etc. as extensions are not to be used unless they are part of the tensioning device. Web lashings shall never be used when knotted. Damage to labels shall be prevented by keeping them away fro sharp edges of the load and, if possible, from the load. The webbing shall be protected against friction, abrasion and damage from loads with sharp edges by using protective sleeves and/or corner protectors.
2013 Certs Assured Ltd. All Rights Reserved.

Lashing System

Uploaded by

Copyright:

Available Formats

Lashing System

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lashing System

Uploaded by

Copyright:

Available Formats

What materials are ratchet lashings and slings commonly made from?

What temperature ranges are ratchet lashings suitable for use in?

On Site Examination & Lifting Equipment Specialists

Instructions for use

2013 Certs Assured Ltd. All Rights Reserved.

You might also like