Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 193 views

    Renishaw Encoders RGH41 Series Readhead

    Uploaded by

    juliangoal
    Renishaw’s 40μm RGH41 series readheads offer all the benefits of the established 20 μm RG2 linear encoder system, such as reflective tape scale, patented filtering optics, set-up LED, good dirt immunity and high speed.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Renishaw Encoders RGH41 Series Readhead

    Uploaded by

    juliangoal
    193 views4 pages
    Renishaw’s 40μm RGH41 series readheads offer all the benefits of the established 20 μm RG2 linear encoder system, such as reflective tape scale, patented filtering optics, set-up LED, good dirt immunity and high speed.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Renishaw’s 40μm RGH41 series readheads offer all the benefits of the established 20 μm RG2 linear encoder system, such as reflective tape scale, patented filtering optics, set-up LED, good dirt immunity and high speed.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    193 views4 pages

    Renishaw Encoders RGH41 Series Readhead

    Uploaded by

    juliangoal
    Renishaw’s 40μm RGH41 series readheads offer all the benefits of the established 20 μm RG2 linear encoder system, such as reflective tape scale, patented filtering optics, set-up LED, good dirt immunity and high speed.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 4

    Data sheet L-9517-0186-03-D

    RGH41 series readhead

    Renishaws 40 m RGH41 series readheads offer all the benefits of the established 20 m RG2 linear encoder system, such as reflective tape scale, patented filtering optics, set-up LED, good dirt immunity and high speed.
    These compact readheads with integral interpolation provide an increased range of resolutions to match the demands of a wide range of applications, whilst their high speed enables an increase in the productivity of the end-users system. The 40 m RGH41 increases the already generous set-up tolerances of the RG2, whilst maintaining Renishaws famous contamination immunity. For added flexibility, dual limit switch sensing is included as standard to enable dedicated signals for each end-of-axis indication, along with a repeatable reference or datum mark.

    These benefits give the RGH41 greater flexibility complementing the breadth of applications in which the RG2 is already used, from co-ordinate measuring and layout machines to electronics assembly and test, linear motors and a host of custom linear motor solutions. Digital range RGH41T - 10 m resolution RGH41D - 5 m resolution RGH41G - 2 m resolution RGH41X - 1 m resolution RGH41N - 0.4 m resolution RGH41W - 0.2 m resolution RGH41Y - 0.1 m resolution RGH41H - 50 nm resolution Analogue range RGH41B - 1 Vpp differential (single limit) RGH41A - 1 Vpp differential (dual limit)

    Non-contact open optical system Large installation tolerances High speed operation up to 15 m/s Industry standard digital and analogue output options Resolutions from 10m to 50 nm Integral reference and dual limit sensors Integral set-up LED Uses Renishaw RGS40-S self-adhesive scale

    RGH41 Installation drawing


    Reference mark sensor position >R50 dynamic bend radius >R10 static bend radius Optical centre 2 holes M3 x 0.5 x 9.5 max (Yaw tol. 1) 0.8 3.6 8.6 3* 9 12.6* >6 4 4 18*

    Data sheet RGH41 series readhead

    Dimensions and tolerances in mm.

    A-9531-0250 reference mark actuator

    14

    7 15.5 23.5 Set-up LED

    14.5

    13

    27

    6 3 10 14.6 14.6 Q limit switch sensor position

    RGS40 scale

    10.5

    2 holes M3 x 0.5 x 7.5 max

    3* 8.6 0.13 (Roll tol. 1) A-9531-0251 Q limit switch actuator Mount dimple up

    A-9531-0251 P limit switch actuator Mount dimple to substrate (size as Q actuator) Arrow indicates forward direction of readhead relative to scale 44 38 3 A

    P limit switch sensor position

    Detail A
    Readhead Scale surface (Pitch tol. 1) 0.8 Readhead to scale clearance Arrow indicates optical and reference mark centre line 2* Rideheight 0.8 0.15

    4.7 max.

    Scale thickness 0.2

    11.6* 5*

    2.2*

    * Dimension measured from substrate

    Alternative mounting faces

    Output specifications
    Digital output signals - RGH41T, D, G, X, N, W, Y, H
    Form - square wave differential line driver to EIA RS422A (except limit switch P, Q, Alarm E- and external set-up signal X) Incremental 2 channels A and B in quadrature (90 phase shifted)
    Signal period P Model RGH41T Resolution S RGH41D RGH41G RGH41X RGH41N RGH40W A B RGH40Y RGH40H P (m) S (m) 40 20 8 4 1.6 0.8 0.4 0.2 10 5 2 1 0.4 0.2 0.1 0.05

    Alarm single limit readheads - differential line driven output dual limit readheads - single-ended line driven output 20 ms minimum
    For RGH41T, G, X alarm asserted for signal amplitude <15 %. Either asynchronous pulse E as shown (options 03/05) or line driver channels 3-state (options 04-06). For RGH41N, W, Y, H - alarm Easserted when: - Signal amplitude >150% - Readhead exceeds specified maximum speed Also, outputs are 3-stated at signal amplitude <15%

    E
    Inverse signal not shown for clarity E- only on dual limit readheads (option 05/06)

    Inverse signal not shown for clarity

    Reference

    Synchronised pulse Z, duration as resolution S. Repeatability of position (uni-directional) maintained within 20 C from temperature at time of phasing and for speeds <0.5 m/s. For RGH40W, Y, H only Z pulse re-synchronised at power-up with any one of the quadrature states (00, 01, 11, 10). Inverse signal not shown for clarity

    External set-up
    5 (nom) voltage at X 0 0 50% signal level 70% 100%

    Between 50% and 70% signal level , X is a duty cycle, 40 m duration. Time spent at 5 V increases with signal level. At >70% signal level X is nominal 5V.

    Limit open collector output Single limit (option 03/04) Dual limit (option 05/06) Length of actuating magnet Q Repeatability < 0.1 mm P, Q Length of actuating magnet Repeatability < 0.1 mm Termination 5 V to 25 V R* P, Q

    Recommended signal termination Readhead A B Z E+ Cable Z0 = 120R A B Z E5V 1k # 120R Customer electronics

    1k

    0V Standard RS422A line receiver circuitry. # Only required on alarm channel E for fail safe operation and to ensure alarm signal is asserted at low signal amplitude on RGH41N, W, Y, H when output is 3-stated

    Asynchronous pulse P, Q. Actuation device A-9531-0251, A-9531-2052, A-9531-2054. *Select R so that the maximum current does not exceed 20 mA. Alternatively, a suitable relay or opto-isolator may be used.

    Analogue output signals - RGH41A, B (1Vpp)


    Incremental 2 channels V1 and V2 differential sinusoids in quadrature (90 phase shifted) 40 m 0.6 to 1.2 Vpp with green LED indication and 120R termination. Limit open collector output Single limit RGH41B Length of actuating magnet Vq Repeatability < 0.1 mm Dual limit RGH41A Repeatability < 0.1 mm Vp Vq Length of actuating magnet Termination 5 V to 25 V R* Vp Vq

    (V1+) - (V1-) 90 (V2+) - (V2-)

    Reference

    0.8 to 1.2 Vpp

    (V0+) - (V0-)

    -18 0

    108

    Differential pulse V0 -18 to 108 . Duration 126 (electrical). Repeatability of position (uni-directional) maintained within 20C from temperature at time of phasing, and for speeds <0.5 m/s. Actuation device A-9531-0250. V0 V1 V2+ 120R V0 V1 V2-

    Asynchronous pulse P, Q. Actuation device A-9531-0251, A-9531-2052, A-9531-2054. *Select R so that the maximum current does not exceed 20 mA. Alternatively, a suitable relay or opto-isolator may be used. External set-up Between 50% and 70% signal level , X is a duty cycle, 20 m duration. Time spent at 5 V increases with signal level. At >70% signal level X is nominal 5V.

    5 (nom) voltage at X 0 0 50% signal level 70% 100%

    Recommended signal termination

    Renishaw plc New Mills, Wotton-under-Edge, Gloucestershire GL12 8JR United Kingdom

    T +44 (0)1453 524524 F +44 (0)1453 524901 E uk@renishaw.com www.renishaw.com

    Operating and electrical specifications


    Speed performance
    Clocked output readheads The RGH41N, W, Y, H readheads are available with a variety of different clocked outputs. The clocked options have been designed to prevent fine edge separations being missed by receiving electronics utilising slower clock speeds. Depending on the clock frequency chosen, each option has a different maximum speed and associated minimum recommended counter clock frequency. Analogue type A/B readheads 100

    Digital readheads
    Head type T D G X N, W, Y, H option 61 62 63 N 3.0 2.6 1.3 Maximum speed (m/s) Minimum recommended counter clock frequency (MHz)
    Encoder velocity (m/s) Resolution (m)

    15
    12 10 6 W 2.5 1.3 0.7

    x4 safety factor

    Signal amplitude (%) 10 1

    Y 1.3 0.7 0.35

    H 0.6 0.3 0.15

    Minimum recommended counter clock frequency (MHz)

    10 Frequency (kHz) 2

    100 4 8 16

    Speed (m/s)

    20 10 5

    Power supply 5 V 5% Ripple Temperature Humidity Sealing Acceleration Shock (non-operating) Vibration (operating) Mass EMC compliance (system) Cable Connector options

    120 mA (typical), 175 mA (RGH41N, W, Y, H) NOTE: For digital outputs, current consumption figures refer to unterminated readheads / interfaces. A further 25 mA per channel pair (eg A+, A-) will be drawn when terminated with 120 . Renishaw encoder systems must be powered from a 5 V dc supply complying with the requirements for SELV of standard EN (IEC) 60950. <200 mVpp maximum @ frequency up to 500 kHz maximum Operating 0 C to +55 C

    Storage -20 C to +70 C

    Storage 95% maximum relative humidity (non-condensing) Operating 80% maximum relative humidity (non-condensing) IP50 Operating 500 m/s 2 BS EN 60068-2-7:1993 (IEC 68-2-7:1983) 1000 m/s 2, 6 ms, sine BS EN 60068-2-27:1993 (IEC 68-2-27:1987) 100 m/s2 max @ 55 Hz to 2000 Hz BS EN 60068-2-6:1996 (IEC 68-2-6:1995) Readhead 50 g Cable 38 g/m

    BS EN 61000 BS EN 55011 12 core, double-shielded, maximum outside diameter 4.7 mm Flex life >20 x 10 6 cycles at 50 mm bend radius Code - connector type D - 15 pin D type plug L - 15 pin D type plug V - 12 pin circular plug W - 12 pin circular coupling plug F - Flying lead X - 16 pin in line connector Application RGH41T, D, G, X, N, W, Y, H RGH41A, B RGH41B RGH41B All readheads All readheads

    For worldwide contact details, please visit our main website at www.renishaw.com/contact
    RENISHAW and the probe emblem used in the RENISHAW logo are registered trademarks of Renishaw plc in the UK and other countries. apply innovation is a trademark of Renishaw plc. 2002-2007 Renishaw plc Issued 0807 Renishaw reserves the right to change specifications without notice

    *L-9517-0186-03*

    You might also like