Professional Documents
Culture Documents
3022
3022
INSTALLATION INSTRUCTIONS
SPECIFICATION
Power Supply : 220/240 Vac, 50 Hz Switch Action : 2 x SPST, type 1B Switch Rating : 220/240 Vac, 50 Hz, 3(1)A Timing Accuracy : +/- 1 min/month Enclosure Rating : IP30 Max. Ambient Temperature : 55C Designed to meet BS EN60730-2-7 Overall Dimensions : 102mm wide, 210mm high, 60mm deep Construction : Class 1 Control Pollution Situation : Degree 2 Rated Impulse Voltage : 2.5Kv Ball Pressure Test : 75C The unit must be installed by a competent electrician and the installation should conform to IEE Wiring Regulations. The supply to this unit should be wired through full disconnect in accordance with BS EN60730-1, i.e. one which provides an air gap of at least 3mm in both poles of the mains, e.g. a 13 amp plug and unswitched socket, or a switched, fused outlet with neon; either fitted with a 3 amp (max.) fuse.
SELECTOR SWITCH
ON OFF TIMED
Time Switch
3022 Terminals
N L
Mains Supply
2 (N) 4
Boiler
N
Pump
N N
Diverter Valve
USER INSTRUCTIONS
3022 PROGRAMMER OPERATING INSTRUCTIONS
1) Setting the programmer (Example 1) i) Decide when you want the ON periods. While griping the Dial Knob slide the dial tappets firmly as shown. The tappets may be quite stiff to move. If you want the switch ON between 7am and 10am and between 5pm (1700 hours) and 11pm (2300 hours), set the tappets as shown (A to 7, B to 10, C to 17 and D to 23). Remember:- Red tappets switch ON Blue tappets switch OFF ii) Using the Dial Knob rotate the dial completely at least twice, clockwise only, to clear the mechanism. A at the first ON time in the day (7) B at the first OFF time in the day (10) C at the second ON time in the day (17) D at the second OFF time in the day (23) 2) Setting the Time (Example 2) Suppose it is 2pm (1400 hours) when you are making this adjustment. Using the dial knob rotate the dial clockwise only until 14 on the dial is next to the Time mark, as shown. Remember that you will have to reset the time after a power cut and also when the clocks change by one hour in spring and autumn. Important: Any adjustment to the time setting must be made by rotating the dial clockwise only. TIMED (Selector switch in the up position). The clock will switch your system ON and OFF according to times at which you have set the four tappet arms. See example 1. OFF (Selector switch in the middle position). This position will completely override the tappet setting and the ON-OFF function of the timeclock enabling you to switch your system off. ON (Selector switch in the down position). This position operates in the opposite way to the OFF position. It will completely override the tappet settings and ON-OFF function of the timeclock enabling you to switch your system ON (e.g. during the winter when the timeclock is in an off position). The 2-way priority switch is set to give the emphasis or priority on the service which you require. On a cold morning for example you may want the heating to come on first. In this case the switch is set to HEATING PRIORITY. Or you may require two baths in succession, so WATER PRIORITY would be selected. Whichever priority is chosen, it will remain in that state until the switch is moved to the other priority position. To obtain water only, select WATER PRIORITY and turn the room thermostat down to the lowest setting.
3) Selecting the Programme Required The two selector switches operate entirely independently of each other as follows: The 3-way selector switch with positions marked TIMED, OFF and ON is used to operate and override the tappet settings on the clock as follows:
Danfoss Randall can accept no responsibility for possible errors in catalogues, brochures and other printed material, and reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
Ampthill Road, Bedford, MK42 9ER Tel: 01234 364621 Fax: 01234 219705 Email: danfossrandall@danfoss.com Website: www.danfoss-randall.co.uk 2 Part No: 7452 Iss.05 05/05