XPEED Outdoor Series: Installation and Operation Manual

www.cnbtec.
com
XPEED Outdoor Series
Ver 1.0
INSTALLATION AND OPERATION MANUAL
(3810-0250A_110119)
WWW.CNBTEC.COM
This lightning flash with arrowhead symbol is intended to alert The user to the presence of un-insulated dangerous voltage Within the products enclosure that may be of sufficient magnitude To constitute a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to The presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Important Safety Instructions

Read Instructions
Read all of the safety and operation instructions before using the product.
Retain Instructions
Save these instructions for future reference.
Attachments / Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause hazards, damage product and void warranty.
Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only with a mounting device recommended by the manufacturer, or sold with the product. To insure proper mounting, follow the manufacturers instructions and use only mounting accessories recommended by manufacturer.
Power source
This product should be operated only from the type of power source indicated on the marking label.
Precautions
Operating
Before using, make sure power supply and others are properly connected. While operating, if any abnormal condition or malfunction is observed, stop using the camera immediately and then contact your local dealer.
Handling
Do not disassemble or tamper with parts inside the camera. do not drop or subject the camera to shock and vibration as this can damage camera. Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your quality of camera.
Installation and Storage

Do not install the camera in areas of extreme temperature, which exceed the allowable range. Avoid installing in humid or dusty places. Avoid installing in places where radiation is present. Avoid installing in places where there are strong magnetic fields and electric signal. Avoid installing in places where the camera would be subject to strong vibrations.
WWW.CNBTEC.COM
Table of Contents
1. Introduction
Features Product & Accessories Parts Name & Functions 4 6 7
2. Installation
Dip Switch Setup Installation Using the Wall Mount Installation Using the Pendant Mount Wire Connections 8 11 12 13
3. Operation
Check Points before Operation Preset and Pattern Function Pre-Check Starting OSD Menu Reserved Preset Preset Swing Pattern Group Other Functions 15 15 15 15 16 16 16 17 17
4. OSD Menu
OSD Display of Main Screen General Rules of key Operation for Menu Main Menu Display Setup Privacy Zone Mask Setup ( 26x (S2465N(P)X), 36x (S2965N(P)X) EXview 27x(SCN-22Z27F /SCN-23Z27F) (Option) Models Only ) Camera Setup (27x (SCN-22Z27F /SCN-23Z27F models) Camera Setup (26x (S2465N(P)X), 36x (S2965N(P)X ) EXview Models) Motion Setup Preset Setup Swing Setup Patten Setup Group Setup System Initialize 18 19 19 19 20 21 23 25 26 28 29 30 32
5. Specifications
26x (S2465N(P)X) EXview Models 27x (SCN-22Z27F/SCN-23Z27F) Models 36x (S2965N(P)X) EXview Models Dimensional Drawings 33 34 35 36
6. System Models and Related Accessories

System Model Numbers Related Accessories 38 38
WWW.CNBTEC.COM
1. Introduction
~ Features
Camera Specifications
Image Pick-up Device: 1/4" Interline Transfer CCD
Zoom Magnification:
26x Optical Zoom, 12x Digital Zoom (Max. 312x Zoom) Model S2465N(P)X 27x Optical Zoom, 10x Digital Zoom (Max. 270x Zoom) Model SCN-22Z27F /SCN-23Z27F 36x Optical Zoom, 12x Digital Zoom (Max. 432x Zoom) Model S2965N(P)X
Day & Night Function
Various Focus Mode : Auto-Focus / Manual Focus / SemiAuto Focus.
Each Preset has its own video configuration, label, relay output setting values. You can adjust each Preset setting independently.
Powerful Pan/Tilt Functions

Max. 360/sec high speed pan/Tilt Movement
Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result, time to target view is reduced dramatically and the video on the monitor is very natural to watch.
For jog operation using a controller, since ultra slow speed 0.05/sec can be reached, it is very easy to locate camera to desired target view. Additionally it is easy to move camera to a desired position with zoom-proportional pan/tilt movement.
Preset, Pattern, Swing, Group, Privacy Mask and More...

Max. 127 Presets are assignable and characteristics of each preset can be set up independently, such as white Balance, Auto Exposure, Label, Digital Outputs and so on.
Max. 8 set of Swing action can be stored. This enables to move camera repetitively between two preset positions with designated speed.
Max. 4 of patterns can be recorded and played back. This enables to move camera to follow any trajectory operated by joystick as closely as possible.
Max. 8 set of Group action can be stored. This enables to move camera repetitively with combination of preset or pattern or Swing. A Group is composed of Max. 20 entities of Preset/Patten/Swings.
Privacy Masks are assignable, not to intrude on others privacy. (8 Privacy Zones) Only available with Models S2465N(P)X, S2965N(P)X, SCN-22Z27F /SCN-23Z27F (option)
PTZ(Pan/Tilt/Zoom) Control
With RS-485 communication, Max. 255 of cameras can be controlled at the same time.
Pelco-D, Pelco-P, Samsung or Panasonic protocol can be selected as a control protocol in the current version of firmware.
WWW.CNBTEC.COM
OSD(On Screen Display) Menu

OSD menu is provided to display the status of camera and to configure the functions interactively.
The information such as Camera ID, Pan/Tilt Angle, Alarm I/O and Preset can be displayed on screen.
Alarm I/O Functions

4 alarm sensor inputs and 2 alarm Output relays are available.
To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo coupler and the relay is used for alarm output.
The signal range of sensor input is from DC 5.0 to 12.0 volts to adopt various applications. Meanwhile, the maximum load of relay contact is 250VAC, 3A or 28VDC, 3A.
If an external sensor is activated, camera con be set to move to the corresponding Preset position. Meanwhile, the output relay can be matched to some specific preset positions to do counteractions such as turning on the light or sound the alarm.
Reserved Presets for Special Purpose

Most camera characteristics can be set up easily and directly with reserved preset, not entering into OSD menu. For more information, refer to Reserved Preset in this manual.
Easy Installation and Perfect Outdoor Environment Compatibility

Fans and heaters are built-in camera for cold and hot temperature environment. Also idealistic mechanical design protects camera from water and dust. (IP 66)
It is easy to install and maintain camera with terminal for cable connection in brackets.
WWW.CNBTEC.COM
1. Introduction Product & Accessories

Basic Components
Other Components (available to be ordered separately)
WWW.CNBTEC.COM
1.
Introduction
Parts Name & Functions
Dome Cover
Do not detach protection vinyl from dome cover before finishing all installation process to protect dome cover from scratches or dust. Sets up camera ID and protocol.
DIP Switch Main Body Cable Drop Prevention Spring
Enables signals and power to come and go between main body and mount bracket.
This part keeps the camera from dropping during installation and maintenance. After install the Bracket, please, hang the spring to the drop prevention hook of main body as shown in picture for further tasks.
Lockup Screw
After assembling main body to bracket, screw main body to bracket to protect them from separation by vibration and so on.
Fuse
If the fuse is burnt to protect your came from over-current damage, the fuse have to be replace with new one. The fuse specification is 250V 2A. however, we recommend consulting with supplier to remove the cause of overcurrent.
Cabling Terminal Block Mold Line TACT Switch
During installation, Power, Video, Communication, Alarm I/O cables are connected on to this cables terminal block.
Mark to assemble main body to bracket. Network Board Factory reset
WWW.CNBTEC.COM
2. Installation
9 Before installing the camera, you should set the DIP switches to configure the camera ID, communication protocol. Do not use the system upgrade terminal.
DIP Switch Setup
Camera ID Setup
ID number of camera is set using binary number. The example is shown bellow.
Pin ID Value ex) ID=5 Ex) ID=10
1 1 ON OFF
2 2 OFF ON
3 4 ON OFF
4 8 OFF ON
5 16 OFF OFF
6 32 OFF OFF
7 64 OFF OFF
8 128 OFF OFF
The range of ID 1~255. Do not use 0 as camera ID. Factory default of Camera ID is 1. If you want to control a certain camera, you must match the camera ID with Cam ID setting of DVR or Controller.
WWW.CNBTEC.COM
2. Installation
Communication Protocol Setup
Select the appropriate Protocol With DIP switch combination.
Switch state Protocol/Baud rate P0 (Pin 1) OFF ON OFF ON OFF ON P1(Pin 2) OFF OFF ON ON OFF OFF Others P2(Pin 3) OFF OFF OFF OFF ON ON PELCO-D, 2400bps PELCO-D, 9600bps PELCO-P, 4800bps PELCO-P, 9600bps SAMSUNG, 4800bps PANASONIC, 9600bps Reserved
If you want to control using DVR or P/T controller, their protocol must be identical to camera. Otherwise, you can not control the camera. It you changed camera protocol by changing DIP S/W, the change will be effective after you reboot the camera. Factory default of protocol is Pelco-D, 2400bps.
Input Sensor Active Type

When a sensor input is used, its functional type should be set. There are two types; Normal Open type and Normal Close type.
-Normal Open : Voltage is let out when the sensor is activated -Normal Close : Voltage is let out when the sensor is not activated
Pin Switch position ON ST1 (Pin 4) OFF ON ST2 (Pin 5) OFF ON ST3 (Pin 6) OFF ON ST4 (Pin 7) OFF Sensor 4 Normal Open Sensor 3 Normal Open Sensor 4 Normal Close Sensor 2 Normal Open Sensor 3 Normal Close Sensor 1 Normal Open Sensor 2 Normal Close Sensor type Sensor 1 Normal Close
If a wrong type of sensor is selected, it activates in the opposite way to the sensor input.
WWW.CNBTEC.COM
Termination Switch Setting

Termination switch (Pin 4) is used in cases listed below. Long-distance communication between the controller and the camera (1-to-1 connection) When the connection distance between the two units is especially long, communication errors may occur due to the impedance of transmission cable. In this case, set the termination switch of both units to ON. Controlling multiple cameras (Multiple connection) The camera may not operate correctly if multiple cameras are connected and controlled. In this case, set the termination switch of the controller and the last connected camera to ON and the switch of other cameras is OFF. Ex) Using the Terminating Resistance.
10
WWW.CNBTEC.COM
2. Installation
Installation Using the Wall Mount
11
WWW.CNBTEC.COM
2. Installation Installation Using the Pendant Mount
12
WWW.CNBTEC.COM
2. Installation Wire Connections
Power Connection
The standard power for the system is 24VAC / 2A. Please, check the voltage and current capacity of rated power carefully.
Video Connection
Connect With BNC coaxial cable.
RS-485 Communication
For PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the same time, RS-485 communication lines of them is connected in parallel as shown below.
13
WWW.CNBTEC.COM
2. Installation
Sensor Input/Relay Output
Sensor input connection
Before connecting sensors, check driving voltage and output signal type of the sensor. Since output signal types of the sensors are divided into Open Collector and Voltage Output type in general, the cabling must be done properly after considering these types. Also, the sensor type, i.e. Normal Open or Normal Close in DIP switch in main body of camera must be set properly.
Signal Line IN COM+
Description Connect(+)cable of electric power source for sensors to this port as shown in the circuit above.
IN1 -, IN2 -, IN3 -, In4 -
Connect output of sensors for each port as shown in the circuit above.
Relay output connection
Maximum allowable electrical load of relay is shown bellow table.
Driving Power Max. Capacity
DC 28VDC, 3A
110VAC 110VAC, 3A
220VAC 250VAC, 3A
14
WWW.CNBTEC.COM
3. Operation Check Points before Operation

Before power is applied, please check the cables carefully. The camera ID of the controller must be identical to that of the target camera. The camera ID can be checked by reading DIP switches of the camera. If your controller supports multi-protocols, the protocol must be changed to match to that of the camera. If you changed camera protocol by changing DIP switches, the change will be effective after you reboot the camera. Since the operation method can be different for each controller available, refer to the manual for your controller if camera can not be controlled properly. The operation of this manual is based on the standard Pelco Controller.
Preset and Pattern Function Pre-Check

Check how to operate preset and pattern function with controller or DVR in advance to operate camera function fully when using controller or DVR. Refer to the following table when using standard Pelco protocol controller.
<Go Preset> <Set Preset> <Run Pattern> <Set Pattern>
Input[Preset Number] and press [Preset] button shortly. Input[Preset Number] and press [Preset] button for more than 2 seconds. Input[Pattern number] and press [Pattern] button shortly. Input[Preset Number] and press [Pattern] button for more than 2 seconds.
If controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For more information, refer to Reserved Preset in this manual.
Starting OSD Menu

Function : Using the OSD menu, Preset, Pattern, Swing, Group and Alarm I/O function can be configured for each application. Enter Menu : <Go Preset> [95]
Reserved Preset
Description Function Some Preset numbers are reserved to special functions. 1. <Go Preset> [95] 2. <Go Preset> [131-134] : Enters into OSD menu : Runs pattern function 1~4
3. <Go Preset> [141~148] : Runs Swing Function 1~8 4. <Go Preset> [151~158] : Runs Group Function 1~8
15
WWW.CNBTEC.COM
3. Operation Preset
Function Max. 127 positions can be stored as Preset position. The Preset number can be assigned from 1 to 128, but 95 is reserved for starting OSD menu. Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently for each preset. Label should be blank and Relay Outputs should be set to OFF as default. Camera Adjust should be set GLOBAL as default. All characteristics can be set up in OSD menu. Set Preset Run Preset Delete Preset <Set Preset> [1~128] <Go Preset> [1~128] To delete Preset, use OSD menu
Swing
Function By using Swing function, you can make camera to move between 2 Preset positions repeatedly. When swing function runs, camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW(Counterclockwise) direction.
In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd point, Camera turns on its axis by 360 in CW(Clockwise) direction and then it turns on its axis by 360 in CCW(Counterclockwise) direction. Speed can be set up from 1/sec to 180/sec Set Swing Run Sing To set Swing, use OSD menu Method 1) <Run Pattern> [Swing NO.+10] ex) Run Swing 3 : <Run Pattern>[13] Method 2) <Go Preset> [Swing NO.+140] ex) Run Swing 3 : <Go Preset>[143] Deleting Swing To delete Swing, use OSD menu.
Pattern
Function Pattern Function is that a camera memorizes the path (mostly curve path) by joystick of controller and preset move functions for assigned time and revives the path exactly as it memorized. 4 Patterns are available and Maximum 1200 communication commands can be stored in a pattern.
Setting Pattern
Pattern can be created by one of following two methods.
Method 1) <Set Pattern> [Pattern NO.] - Pattern editing screen is displayed as bellow. - Movement by Joystick and preset movement can be memorized in a pattern. - The rest memory size is displayed in progress bar. - To save the recording, press NEAR key and to cancel, press FAR key.
Method 2) Using OSD Menu : See the section how to use OSD Menu.
Run Pattern
Method 1) <Run Pattern>[Pattern NO.]
ex) Run Pattern 2 : <Run Pattern>[2]
Method 2) <Go Preset>[Pattern NO.+130] ex) Run Pattern 2 : <Go Preset>[132]
Delete Pattern
Use OSD menu to delete a Pattern.
16
WWW.CNBTEC.COM
3. Operation Group
Function The group function allows running sequence of Presets, Pattern and/or Swings. Max. 8 group can be stored. Each group can have max. 20 action entities which can be preset, pattern or swing. Preset speed can be set up and the repeat number of pattern & Swing can be set up in Group setup. Dwell time between actions can be set up also.
Setting Group Run Group
Use OSD Menu to create a Group. 1) <Run Pattern>[Group No.+20] ex)Run Group7 : <Run Pattern>[27] 2) <Go Preset>[Group No.+150] ex)Run Group7 : <Go Preset>[157]
Deleting Group
Use OSD Menu to delete.
Other Functions
Power Up Action This function enables to resume the last action executed before power down. Most of actions such as Preset, Pattern, Swing and Group are available fort his function but Jog actions are not available to resume.
Auto Flip
In case that tilt angle arrives at the top of tilt orbit(90), the zoom module camera pans180 to keep tracing targets. If this function is set to OFF, tilt movement range is 0~95
Park Action
This function enables to locate the camera to specific position automatically if operator doesnt operate the controller for a while. The park Time can be defined as an interval from 1 minute to 4 hours.
Alarm I/O
4 Alarm Inputs and 2 Alarm Outputs (Relay output) are used. If an external sensor is activated, camera can be set to move to corresponding preset position. Also, the output relay can be matched to some specific preset positions to do counteractions such as turning on the light or sounding the alarm. It is noted that the latest alarm input is effective if multiple sensors are activated.
Privacy Zone Mask
To protect privacy, Max. 8 Privacy Masks can be created on the arbitrary position to hide objects such as windows, shops or private house. With Spherical Coordinates system, powerful Privacy Zone Mask function is possible. This function is only available with S2465N(P)X, S2665N(P)X, S2965N(P)X and SCN-22Z27F /SCN-23Z27F(P)(Option).
Global/Local Image Setup
WB(White Balance) and AE(Auto Exposure) can be set up independently for each preset. There are 2modes, Global mode & Local Mode. The Global mode means that WB or AE can be set up totally and simultaneously for all presets in ZOOM CAMERA SETUP menu. The Local mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu. Each Local WB/AE value should activate correspondingly when camera arrives at each preset location. During jog operation, Global WB/AE value should be applied. All Local WB/AE value do not change although Global WB/AE value changes.
SemiAuto Focus
This mode exchanges focus mode automatically between Manual Focus mode and Auto focus mode by operation. Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation. With Manual mode at preset, Focus data is memorized in each preset in advance and camera calls focus data in correspondence with presets as soon as camera arrives at a preset. It should shorten time to get focuses. Focus mode changes to Auto Focus mode automatically when jog operation starts.
17
WWW.CNBTEC.COM
4. OSD Menu OSD Display of Main Screen
P/T/Z Information
Current Pan/Tilt angle in degree, zoom magnification and a compass direction.
Camera ID
Current Camera ID (Address).
Action Title
Followings are possible Action Titles and their meaning. SET PRESET xxx PRESET xxx PATTERN x SWGx/PRESET xxx UNDEFINED When Preset xxx is stored When camera reach to preset xxx
When Pattern x is in action When Swing x is in action When undefined function is called to run
Preset Label
The Label stored for specific Preset.
Alarm Information
This information shows current state of sensor input and relay output. If the Input and output points are ON state it will show a number corresponding to each point When they are OFF state, -will be displayed. Ex) point 2&3 of inputs and 1 of output are ON, OSD will show as below
18
WWW.CNBTEC.COM
4. OSD Menu General Rules of key Operation for Menu

The menu items surrounded with < > always has its sub menu. For all menu level, to go into sub menu, press NEAR key. To go to up-one-level menu, press FAR key. To move from items to item in the menu, use joystick in the Up/Down or Left/Right. To change a value of an item, use Up/Down of the joystick in the controller. Press NEAR key to save values and Press FAR key to cancel values. Specifications and functions should be different by models.
Main Menu
SYSTEM INFORMATION DISPLAU SETUP DOME CAMERA SETUP SYSTEM INITIALIZE Displays system information and configuration. Enable/Disable of OSD display on Main Screen. Configure various functions of this camera. Initializes system configuration and sets all data to factory default configuration.
Display Setup
This menu defines Enable/Disable of OSD display on main Screen, If an item is set to be AUTO, the item is displayed only when the value of it is changed. CAMERA ID PTZ INFORMATION ACTION TITLE PRESET LABEL ALARM I/O [ON/OFF] [ON/OFF/AUTO] [ON/OFF/AUTO] [ON/OFF/AUTO] [ON/OFF/AUTO]
COMPASS DIRECTION SETUP

Set North to assign compass direction as criteria. Move camera and press NEAR button to save.
19
WWW.CNBTEC.COM
4. OSD Menu Privacy Zone Mask Setup

(Models S2465N(P)X, S2965N(P)X, SCN-22Z27F /SCN-23Z27F (Option) Only)
Select area in image to mask. MASK NO [1~8] Select Mask number. If the selected mask has already data, camera moves as it was set. Otherwise, UNDEFINED will be displayed under MASK NO. DISPLAY [ON/OFF] Sets if camera makes mask shows or not on images. CLEAR MASK [CANCEL/OK] Deletes data in the selected mask NO.
Privacy Zone Area Setup

Move camera to the area to mask. Then the menu to adjust mask size will be displayed.
Privacy Zone Size Adjustment

Adjust mask size, Use joystick or arrow buttons to adjust mask size. (Left/Right) (Up/Down) Adjusts mask width. Adjusts mask height.
20
WWW.CNBTEC.COM
4. OSD Menu
Camera Setup ( Model SCN-22Z27F /SCN-23Z27F)
Setup the general functions of 27x optical zoom camera module. FOCUS MODE [AUTO/MANUAL/SEMIAUTO] Sets camera focus mode. MAX ZOOM [x1 ~ x270] Sets the maximum zoom magnification. FLICKERLESS [ON/OFF] When an NTSC camera if used under 50Hz and PAL under 60Hz flickering may appear on the screen. When this happens, turn FLICKERLESS setting ON. This prevents flickering which happens when the frequency of the power and the frequency of camera are different. When FLICKERLESS in ON, Day&Night mode goes DAY and Digital Slow Shutter mode goes OFF automatically. COLOR [ON/OFF] Switching color mode to black-white mode LINE LOCK [ON/OFF] If Line lock sync is ON, video signal is synchronized with AC power. Video can be fluctuated after setting is changed.
WHITE BALANCE SETUP

WB MODE [AUTO/MANUAL] In Manual mode, Red and Blue level can be setup manually. RED ADJUST BLUE ADJUST [0~255] [0~255]
21
WWW.CNBTEC.COM
4. OSD Menu
AUTO EXPOSURE SETUP
BACKLIGHT [OFF/C1/C2/L1/L2/U1/U2/D1/D2/R1/R2] Sets Backlight Compensation. The reference position and the level of BLC are selectable. Refer to the table below. Note1) DAY/NIGHT SLOW SHOUTTER [AUTO/DAY/NIGHT] [OFF/2~128 Field] Activates SLOW SHUTTER function when luminance of image(signal) is too dark. It is possible to set up the maximum number of fields piled up one on another by SLOW SHUTTER function. It is only available when DAY/NIGHT mode is DAY AE MODE [AUTO/SHUTTER/IRIS/AGC/MANUAL] There are five modes of Auto Exposure function. Except AUTO mode, the others can be selected when DAY/NIGHT mode is DAY and Slow Shutter mode is OFF. IRIS LEVEL GAIN LEVEL SHUTTER SPEED [0~255] It can be set when AE is in IRIS mode or MANUAL mode. [0~255] It can be set when AE is in AGC mode or MANUAL mode. [0~27] It can be set when AE is in SHUTTTER SPEED mode or in MANUAL mode. As for setting value, refer to the table below. Note2) BRIGHTNESS [0~96] It can be set when AE is not in MANUAL mode.
Note1) Backlight Compensation

Value C1 L1 U1 D1 R1 Description Low weight at the center of the screen Low weight at the left of the screen Low weight at the upper of the screen Low weight at the lower of the screen Low weight at the right of the screen Value C2 L2 U2 D2 R2 Description High weight at the center of the screen High weight at the left of the screen High weight at the upper of the screen High weight at the lower of the screen High weight at the right of the screen
*The values are based on NTSC type models.
Note2) Shutter Speed Table

Value 0 1 2 3 4 5 6 Shutter 1/60 sec 1/125 sec 1/150 sec 1/200 sec 1/250 sec 1/300 sec 1/350 sec Value 7 8 9 10 11 12 13 Shutter 1/400 sec 1/450 sec 1/500 sec 1/600 sec 1/700 sec 1/800 sec 1/900 sec Value 14 15 16 17 18 19 20
Shutter 1/1000 sec 1/1100 sec 1/1300 sec 1/1500 sec 1/1600 sec 1/1800 sec 1/2000 sec
Value 21 22 23 24 25 26 27
Shutter 1/2500 sec 1/2500 sec 1/3000 sec 1/3500 sec 1/4000 sec 1/6000 sec 1/10000 sec
22
WWW.CNBTEC.COM
4. OSD Menu Camera Setup ( Models S2465N(P)X, S2965N(P)X)

Setup the general functions of 26x / 36x optical zoom modules. FOCUS MODE [AUTO/MANUAL/SEMIAUTO] Sets camera focus mode. DIGITAL ZOOM [ON/OFF] Sets digital zoom on or off. FLICKERLESS [ON/OFF] When an NTSC camera is used under 50Hz or PAL under 60Hz, flickering may appear on the screen. When this happens, turn Flickerlees setting ON. This prevents flickering which happens when the frequency of the power and the frequency of camera are different. COLOR [ON/OFF] Switching color mode to black-white mode. LINE LOCK [ON/OFF] If Line lock sync is ON, video signal is synchronized with AC power. Video can be fluctuated after setting is changed.
WHITE BALANCE SETUP

WB MODE [AUTO/MANUAL] In Manual mode, Red and Blue level can be setup manually. RED ADJUST BLUE ADJUST [0~255] [0~255]
23
WWW.CNBTEC.COM
4. OSD Menu
AUTO EXPOSURE SETUP
BACKLIGHT [ON/OFF] Sets Backlight Compensation. DAY/NIGHT AE MODE [AUTO/DAY/NIGHT] [AUTO/SHUTTER/IRIS/GAIN/BRIGHT/MANUAL] Selects automatic exposure mode. Each mode appears with adjustable values. When Flickeress mode is ON, AE mode is automatically in SHUTTER SPEED mode. IRIS LEVEL [CLOSE/F1.6~F28] (Model S1465N(P)X, S1965N(P)X) [CLOSE/F1.4~F22] (Model S1665N(P)X) It can be set when AE is in IRIS mode or MANUAL mode. GAIN LEVEL [3dB~28dB] It can be set when AE is in MANUAL mode. SHUTTER SPEED [1/1sec~1/10000sec] It can be set when AE is in SHUTTER SPEED mode or MANUAL mode. BRIGHTNESS [0~31] It can be set when AE is in BRIGHTNESS mode. WDR Only available with S1965N(P)X Models.
24
WWW.CNBTEC.COM
4. OSD Menu Motion Setup

Setup the general functions of Pan/Tilt motions. MOTION LOCK [ON/OFF] If Motion Lock is set to ON, it is impossible to set up and delete Preset Swing, Pattern and Group. It is possible only to run those functions. To set up and elete those functions, enter into OSD menu. PWR UP ACTION [ON/OFF] Refer to Other Functions section. AUTO FLIP [ON/OFF] Refer to Other Functions section. JOG MAX SPEED [1/sec~360/sec] Sets maximum jog speed. Jog speed is inversely proportional to zoom magnification. As zoom magnification goes up, pan/tilt speed goes down. JOG DIRECTION [INVERSE/NORMAL] If you set this to Inverse, the view in the screen is moving same direction with jog tilting. If Normal is selected, the view in the screen is moving reversely. FRZ IN PRESET [ON/OFF] (27x, 36x Models Only) If Freeze in preset function mode is ON, camera starts freezing the image of start point at start point of preset movement. Camera keeps displaying the image of start point during preset movement and does not display the images which camera gets during preset movement. As soon as camera stops at preset end point, camera start displaying live images which it gets at preset end point. This function is only available with 27x ,36x Models.
PARK ACTION SETUP

If Park Enable is set to ON, camera runs assigned function automatically if there is no PTZ command during assigned Wait Time. PARK ENABLE WAIT TIME [ON/OFF] [1 minute ~ 4 hours] The time is displayed with hh:mm:ss format and you can change this by 1 min unit. PARK ACTION [HOME/PRESET/PATTERN/SWING/GROUP] If it is set to HOME, all the functions go back to HOME position (PAN,TILT,ZOOM)=(0, 0, x1).
25
WWW.CNBTEC.COM
4. OSD Menu
ALARM ACTION SETUP
Sets the preset to move to when the alarm is input. ALARM N ACT [NOT USED/PRESET 1~128] Assign counteraction Preset position to each Alarm input
Preset Setup
PRESET NO. [1~128] If a selected preset is already defined, camera moves to pre-defined position and preset characteristics such as Label and Relay Outputs show on monitor. If a selected preset is not defined, UNDEFINED shows on monitor. CLR PRESET [CANCEL/OK] Delete current Preset data. EDIT SCENE EDIT LABEL Redefine current Preset scene position (i.e.PTZ). Edits Label to show on monitor when preset runs. MAX. 10 alphabets are allowed. RELAY OUT Sets the relay output. The figure on the right is current Setting value. '-' indicates OFF mode. If the relay is shown as figures, it means relay is ON. CAM ADJUST [GLOBAL/LOCAL] WB(White Balance) and AE(Auto Exposure) can be set up independently for each preset. There are 2 modes, Global mode & local mode. The Global mode means that WB or AE can be set up totally and simultaneously for all presets in ZOOM CAMERA SETUP menu. The local mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu. Each Local WB/AE value should activate correspondingly when camera arrives at each preset location. During jog operation, Global WB/AE value should be applied. All Local WB/AE value should not change although Global WB/AE value changes. If local is selected, Menu to set WB/AE shows on monitor.
26
WWW.CNBTEC.COM
4. OSD Menu
EDIT PRESET SCENE
Using Joystick, move camera to desired position.
By pressing NEAR key, save current PTZ data.
Press FAR key to cancel.
EDIT PRESET LABEL

Edits label to show on monitor when camera arrives at presets. In Edit label menu, a reverse rectangular is cursor. As soon as finishing selecting alphabet, cursor moves to the next digit.
Using Left/Right/Up/Down of joystick, move to an appropriate character from the Character set. To choose that character, press the NEAR key.
If you want to use blank, choose Space character( ). If you want To delete a character before, use back space character( ).
If you complete the Label editing, move cursor to OK and press NEAR key to save completed label. To abort current change, move cursor to Cancel and press NEAR key.
EDIT RELAY OUT

RELAY OUT N [ON/OFF] Sets relay output when changing preset position.
27
WWW.CNBTEC.COM
4. OSD Menu Swing Setup

SWING NO. [1~8] Selects Swing number to edit. If a selected Swing has not defined, NOT USED is displayed in 1st Position and 2nd Position. 1ST POS. 2ND POS. [PRESET 1~128] Set up the 2 position for Swing function. If a selected preset is not defined, UNDEFINED will be displayed as shown below.
When swing function runs, camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point is CCW(Counterclockwise) direction. In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd point, camera turns on its axis by 360 in CW direction and then it turns on its axis by 360 in CCW direction. SWING SPEED [1/sec~180/sec] Sets Swing speed from 1/sec to 180/sec. CLEAR SWING [CANCEL/OK] Deletes current Swing data.
28
WWW.CNBTEC.COM
4. OSD Menu Pattern setup

PATTERN NO. [1~4] Selects Pattern number to edit. If a selected pattern number is not defined, UNDEFINED will be displayed under selected pattern number. CLR PATTERN [CANCEL/OK] Deletes data in current pattern. EDIT PATTERN Starts editing pattern.
EDIT PATTERN
By using Joystick, move to start position with appropriate zoom. To start pattern recording, press NEAR key. To exit this menu, press FAR key.
Move camera with joystick of controller or run preset function to memorize the path (mostly curve path) in a selected pattern. The total memory size and the rest memory size is displayed in the form of bar. Maximum 1200 communication commands can be stored in a pattern. To save data and exit, press NEAR key. To cancel recording and delete record data, press FAR key.
29
WWW.CNBTEC.COM
4. OSD Menu Group Setup

GROUP NO. [1~8] Selects a group number. If the selected number is not set, UNDEFINED will be displayed selected Group number. CLEAR GROUP [CANCEL/OK] Clears the current setting of a group. EDIT GROUP Starts editing Group.
EDIT GROUP
Press NEAR key in NO list to start Group setup.
Note that MAX. 20Functions are allowed in a Group. Move cursor up/down and press NEAR key to set up.
Set up Action, Dwell time and Option. Note that selected item is displayed in reverse. Move cursor Left/Right to select items and move cursor Up/Down to change each value. ACTION ### DWELL [NONE/PRESET/SWING/PATTERN] [0 sec~4min] Sets Dwell Time between functions. OPT (Option) It should be preset speed when preset is set in Action. Is should be the number of repeat when Pattern or Swing is selected in Action.
30
WWW.CNBTEC.COM
4. OSD Menu
Set up items such as Action, ###, Dwell and OPT
After finishing setting up a Action, press NEAR key to one-upper-Level Menu(Step). Move cursor Up/Down to select Action Number and repeat Step ~ Step to edit selected Group.
After Finishing setting up all Action, press FAR key to exit. Then cursor should be moved to SAVE. Press NEAR key to save data.
31
WWW.CNBTEC.COM
4. OSD Menu System Initialize

CLEAR ALL DATA Deletes all configuration data such as display, camera, motion setup and so on. CLR DISPLAY SET CLR CAMERA SET CLR MOTION SET CLR EDIT DATA Initializes Display Configuration. Initializes camera Configuration. Initializes Motion Configuration. Deletes Preset Data, Swing Data, Pattern Data and Group Data. REBOOT CAMERA REBOOT SYSTEM Reboots Zoom Camera module. Reboots Speed Dome Camera.
Initial setting
Display setting
Camera ID PTZ Information Action Title Preset Label Alarm I/O North Direction Privacy Zone ON AUTO AUTO AUTO AUTO Pan 0 Undefined
Camera setting
Focus mode Digital Zoom Max Zoom Flickerless Color Line Lock White Balance Backlight Day&Night Slow Shutter AE Mode Brightness SemiAuto ON X216 X270 / x312 / x432 OFF ON OFF AUTO OFF AUTO OFF AUTO 50
Motion setting
Motion Lock Power up Action Auto Flip Jog Max Speed Jog Direction Park Action Alarm Action FRZ IN PRESET OFF ON ON 120 /sec INVERSE OFF OFF OFF
User setting data

Preset 1~128 Swing 1~8 Pattern 1~4 Group 1~8 Undefined Undefined Undefined Undefined
Above functions are only available with the following models; : S2465N(P) : S2965N(P)X : SCN-22Z27F /SCN-23Z27F(P)(Option)
32
WWW.CNBTEC.COM
5. Specifications ~ 26x EXview Models S2465NX / S2465PX

Video Signal
Image Pick-up Device Effective Pixels Horizontal Resolution S/N Ratio Zoom Focal Length Camera Aperture Range Minimum Illumination Day & Night Focus AE Mode White Balance BLC Flickerless Operation Range
NTSC
1/4 EXview HAD CCD 768(H) x 494(V) 380K 470 TV Lines More than 50 db
PAL
752(H) x 582(V) 440K 460 TV Lines
Types by installation
26x Optical Zoom, 12x Digital Zoom f=3.5(Wide)-91(Tele)mm F1.6(Wide)-3.8(Tele) 1.0Lux (Color) / 0.07Lux (Color, DSS) / 0.15 Lux (B/W,DSS) Auto / Day /Night (IR Cut Filter) Auto / Manual / SemiAuto Auto / Iris / Shutter / Manual / Brightness Auto / Manual( Red, Blue Gain Adjustable) On / Off On / Off Pan 360 (Endless) / Tilt 90 Preset : 360 / sec
Operation Speed
Manual : 1 ~ 360 / sec (inter-locked with zoom extension) Swing : 1 ~ 180 /sec
Pan/Tilt
Preset Setting Swing Setting Pattern Setting Group Setting Other Functions Communication Protocol Privacy Zone Alarm I/O OSD Menu Input Voltage
127 presets (label setting, individual video setting) 8 swings 4 pattern (1200 commands / pattern, 5 min) 8 groups (20 actions / group) Auto Flip, Auto Parking, Power Up Action RS-485 Pelco-D, Pelco-P, Samsung and Panasonic Selectable 8 Zones 4 inputs / 2 outputs On / Off 24VAC (19VAC ~ 29VAC) 48VA 2A Dome 149
General
Input Power Fuse Dimension
Housing : 209.7 x 247.2(H) mm (without Sun-Sheild) Weight(Approx.) Operational Temperature 3.8kg (without Sun-Sheild) / 4.3kg (with Sun-Sheild) -30 C ~ +50 C
33
WWW.CNBTEC.COM
5. Specifications
~ 27x Models SCN-22Z27F /SCN-23Z27F
NTSC
Image Pick-up Device Effective Pixels Horizontal Resolution Resolution S/N Ratio Zoom Focal Length Aperture Range Minimum Illumination Camera Day & Night Focus Iris Shutter Speed AGC White Balance BLC Flickerless Brightness Operation Range 1/4 IT CCD 811(H) x 508(V) 410K 768(H) x 494(V) 380K 795(H) x 596(V) 470K 752(H) x 582(V) 440K
Video Signal
PAL
580 TV Lines (BW 600 TV Lines), Sharpness Max. 50 dB (AGC Off) 27x Optical Zoom, 10x Digital Zoom f=3.6(Wide) - 97.2(Tele)mm F1.6(Wide)-3.7(Tele) 0.5Lux (30 IRE)Color / 0.1Lux (30 IRE) B/W / DSS(128FLD) Mode : 0.0005Lux (30 IRE) Auto / Day /Night Auto / Manual / SemiAuto Auto / Manual Auto (x128 ~ 1/60 sec ~ 1/10,000 sec) Normal / High / Off Auto / Manual( Red, Blue Gain Adjustable) NORMAL,C,L,U,D,R HIGH/LOW(6 Area Selectable) On / Off Adjustable (0-96) Pan 360 (Endless) / Tilt 90 Preset : 360 / sec
Operation Speed
Pan/Tilt
Preset Setting Swing Setting Pattern Setting Group Setting Other Functions Communication Protocol Privacy Zone(Option) Alarm I/O OSD Menu Input Voltage
General
34
WWW.CNBTEC.COM
5. Specifications 36x EXview Models S2965NX /S2965PX

Video Signal
Image Pick-up Device Effective Pixels Horizontal Resolution S/N Ratio Zoom Focal Length Aperture Range Camera
NTSC
1/4 EXview HAD CCD 768(H) x 494(V) 380K 530 TV Lines 50 dB (Weight ON)
PAL
752(H) x 582(V) 440K
36x Optical Zoom, 12x Digital Zoom f=3.4(Wide) ~ 122.4(Tele)mm F1.6(Wide) ~ 4.5(Tele) 1.4 Lux 1/60 sec(NT), 1/50 sec(PAL)
Minimum Illumination
0.1Lux 1/4 sec(NT), 1/3 sec(PAL) 0.01Lux 1/4 sec(NT), 1/3 sec(PAL) : ICR-ON
Day & Night Focus AE Mode White Balance BLC Flickerless Operation Range
Auto / Day / Night / WDR Auto / Manual / SemiAuto Auto / Iris / Shutter / Manual / Brightness Auto / Manual( Red, Blue Gain Adjustable) On / Off / WDR On / Off Pan 360 (Endless) / Tilt 90 Preset : 360 / sec
Operation Speed
Pan/Tilt
Preset Setting Swing Setting Pattern Setting Group Setting Other Functions Communication Protocol Privacy Zone Alarm I/O OSD Menu Input Voltage
General
35
WWW.CNBTEC.COM
5. Specifications Dimensional Drawings
Unit (mm)
36
WWW.CNBTEC.COM
5. Specifications Dimensional Drawings
Unit (mm)
37
WWW.CNBTEC.COM
6. System Models & Related Accessories System Model Numbers

26x Day/Night(ICR) / EX view HAD CCD Super HAD CCD EX view HAD CCD 27x Day/Night(ICR) 36x Day/Night(ICR)
S2465NXW S2465PXW
SCN-22Z27FW SCN-23Z27FW
S2965NXW S2965PXW
S2465NXP S2465PXP
SCN-22Z27FP SCN-23Z27FP
S2965NXP S2965PXP
SS2465NXW SS2465PXW
SDN-22Z27FW SDN-23Z27FW
SS2965NXW SS2965PXW
SS2465NXP SS2465PXP
SDN-22Z27FP SDN-23Z27FP
SS2965NXP SS2965PXP
S2465NX S2465PX
SCN-22Z27F SCN-23Z27F
S2965NX S2965PX
SS2465NX SS2465PX
SDN-22Z27F SDN-23Z27F
SS2965NX SS2965PX
Related Accessories Wall Mount Pendant Mount Corner Mount Pole mount Sun Shield SWB2000 SPB2000 SCB2000 SOB2000 SSS2000
38
WWW.CNBTEC.COM
MEMO
39

XPEED Outdoor Series: Installation and Operation Manual

Uploaded by

Copyright:

Available Formats

XPEED Outdoor Series: Installation and Operation Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

XPEED Outdoor Series: Installation and Operation Manual

Uploaded by

Copyright:

Available Formats

www.cnbtec.

XPEED Outdoor Series

INSTALLATION AND OPERATION MANUAL

XPEED Outdoor Series

Important Safety Instructions

Installation and Storage

XPEED Outdoor Series

6. System Models and Related Accessories

XPEED Outdoor Series

Day & Night Function

Various Focus Mode : Auto-Focus / Manual Focus / SemiAuto Focus.

Powerful Pan/Tilt Functions

Preset, Pattern, Swing, Group, Privacy Mask and More...

XPEED Outdoor Series

OSD(On Screen Display) Menu

Alarm I/O Functions

Reserved Presets for Special Purpose

Easy Installation and Perfect Outdoor Environment Compatibility

XPEED Outdoor Series

1. Introduction Product & Accessories

Other Components (available to be ordered separately)

XPEED Outdoor Series

Parts Name & Functions

DIP Switch Main Body Cable Drop Prevention Spring

Cabling Terminal Block Mold Line TACT Switch

Mark to assemble main body to bracket. Network Board Factory reset

XPEED Outdoor Series

DIP Switch Setup

Pin ID Value ex) ID=5 Ex) ID=10

8 128 OFF OFF

XPEED Outdoor Series

Input Sensor Active Type

XPEED Outdoor Series

Termination Switch Setting

XPEED Outdoor Series

XPEED Outdoor Series

2. Installation Installation Using the Pendant Mount

XPEED Outdoor Series

2. Installation Wire Connections

XPEED Outdoor Series

Signal Line IN COM+

IN1 -, IN2 -, IN3 -, In4 -

Relay output connection

Maximum allowable electrical load of relay is shown bellow table.

Driving Power Max. Capacity

XPEED Outdoor Series

3. Operation Check Points before Operation

Preset and Pattern Function Pre-Check

<Go Preset> <Set Preset> <Run Pattern> <Set Pattern>

Starting OSD Menu

XPEED Outdoor Series

Pattern can be created by one of following two methods.

Method 1) <Run Pattern>[Pattern NO.]

ex) Run Pattern 2 : <Run Pattern>[2]

Method 2) <Go Preset>[Pattern NO.+130] ex) Run Pattern 2 : <Go Preset>[132]

Use OSD menu to delete a Pattern.

XPEED Outdoor Series

Setting Group Run Group

Use OSD Menu to delete.