3GPP TS 25.304

3GPP TS 25.304 V7.8.
0 (2009-09)
Technical Specification
3rd Generation Partnership Project; Technical Specification Group Radio Access Network; User Equipment (UE) procedures in idle mode and procedures for cell reselection in connected mode (Release 7)
The present document has been developed within the 3rd Generation Partnership Project (3GPP TM) and may be further elaborated for the purposes of 3GPP. The present document has not been subject to any approval process by the 3GPP Organizational Partners and shall not be implemented. This Specification is provided for future development work within 3GPP only. The Organizational Partners accept no liability for any use of this Specification. Specifications and reports for implementation of the 3GPP TM system should be obtained via the 3GPP Organizational Partners' Publications Offices.
Release 7
3GPP TS 25.304 V7.8.0 (2009-09)
Keywords
UMTS, radio
3GPP Postal address
3GPP support office address

650 Route des Lucioles - Sophia Antipolis Valbonne - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Internet
http://www.3gpp.org
Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
2009, 3GPP Organizational Partners (ARIB, ATIS, CCSA, ETSI, TTA, TTC). All rights reserved. UMTS is a Trade Mark of ETSI registered for the benefit of its members 3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners LTE is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners GSM and the GSM logo are registered and owned by the GSM Association
3GPP
Release 7
3GPP TS 25.304 V7.8.0 (2009-09)
Contents
Foreword ......................................................................................................................................................5 1 2 3
3.1 3.2
Scope..................................................................................................................................................6 References ..........................................................................................................................................6 Definitions and abbreviations ..............................................................................................................7

Definitions...................................................................................................................................................7 Abbreviations...............................................................................................................................................8
4
4.1 4.2 4.3
General description of Idle mode.......................................................................................................10

Overview ...................................................................................................................................................10 Functional division between AS and NAS in Idle mode ..............................................................................11 Service type in Idle and Connected Mode ...................................................................................................13
Process and procedure descriptions ...................................................................................................14
5.1 PLMN selection .........................................................................................................................................14 5.1.1 General.................................................................................................................................................14 5.1.2 Support for PLMN Selection.................................................................................................................14 5.1.2.1 General ...........................................................................................................................................14 5.1.2.2 UTRA case .....................................................................................................................................15 5.1.2.3 GSM case........................................................................................................................................15 5.2 Cell selection and reselection in idle mode..................................................................................................15 5.2.1 Introduction..........................................................................................................................................15 5.2.2 States and state transitions in Idle Mode ................................................................................................16 5.2.2.1 Cell Selection process overview.......................................................................................................16 5.2.2.2 Camped normally state overview .....................................................................................................17 5.2.2.3 Connected mode State overview ......................................................................................................17 5.2.2.4 Any cell selection State overview ....................................................................................................17 5.2.2.5 Camped on any cell State overview..................................................................................................17 5.2.3 Cell Selection Process...........................................................................................................................18 5.2.3.1 UTRA case .....................................................................................................................................18 5.2.3.1.1 Description ................................................................................................................................18 5.2.3.1.2 Criteria ......................................................................................................................................18 5.2.3.2 GSM case........................................................................................................................................19 5.2.4 Void .....................................................................................................................................................19 5.2.5 Camped Normally State ........................................................................................................................19 5.2.5.1 UTRA case .....................................................................................................................................19 5.2.5.2 GSM case........................................................................................................................................19 5.2.6 Cell Reselection Evaluation Process......................................................................................................19 5.2.6.1 UTRA case .....................................................................................................................................19 5.2.6.1.0 Use of MBMS PL ......................................................................................................................20 5.2.6.1.1 Measurement rules for cell re-selection when HCS is not used ....................................................20 5.2.6.1.1a High mobility state when HCS is not used ..................................................................................20 5.2.6.1.2 Measurement rules for cell re-selection when HCS is used..........................................................21 5.2.6.1.3 Highest ranked cells with cell reservations, access restrictions or unsuitable for normal camping.....................................................................................................................................23 5.2.6.1.4 Cell Reselection Criteria ............................................................................................................23 5.2.6.1.5 Cell reselection parameters in system information broadcasts......................................................27 5.2.6.2 GSM case........................................................................................................................................30 5.2.7 Cell Selection when leaving connected mode ........................................................................................30 5.2.7.1 UTRA case .....................................................................................................................................30 5.2.7.2 GSM case........................................................................................................................................30 5.2.8 Any Cell Selection state........................................................................................................................30 5.2.9 Camped on Any Cell State ....................................................................................................................30 5.2.9.1 UTRA case .....................................................................................................................................30 5.2.9.2 GSM case........................................................................................................................................30 5.3 Cell Reservations and Access Restrictions (cells not operating in MBSFN mode)........................................31 5.3.1 UTRA cells ..........................................................................................................................................31
3GPP
Release 7
3GPP TS 25.304 V7.8.0 (2009-09)
5.3.1.1 5.3.1.2 5.3.1.3 5.3.2 5.3a 5.4 5.4.1 5.4.2 5.4.3 5.4.4 5.5
Cell status and cell reservations .......................................................................................................31 Access Control ................................................................................................................................32 Emergency Call...............................................................................................................................32 GSM cells.............................................................................................................................................32 Cell Reservations and Access Restrictions (MBSFN cells only for FDD and 3.84/7.68 Mcps TDD).............32 Cell Selection and Reselection Processes in RRC Connected Mode.............................................................33 Void .....................................................................................................................................................33 Void .....................................................................................................................................................33 Cell Reselection Process in RRC connected mode .................................................................................33 Cell Selection Process in RRC connected mode.....................................................................................33 Location Registration .................................................................................................................................33
6
6.1 6.2 6.3 6.3.1 6.3.1.1 6.3.1.2 6.3.1.3
Broadcast information receiving........................................................................................................33

Reception of System Information ...............................................................................................................33 Cell Broadcast in Idle Mode, CELL_PCH and URA_PCH..........................................................................33 MBMS Services.........................................................................................................................................34 MBSFN cluster selection and reselection...............................................................................................34 MBSFN cluster selection .................................................................................................................34 Camped on MBSFN cluster .............................................................................................................34 MBSFN inter frequency neighbour information ...............................................................................35
7 8
8.1 8.2 8.2b 8.3 8.4 8.4.1 8.4.1.1 8.4.1.2 8.4.2
Void .................................................................................................................................................35 Paging and SCCPCH selection and in FDD the H-RNTI selection.....................................................35
Paging Channel selection ...........................................................................................................................35 SCCPCH selection when entering Connected mode ....................................................................................35 H-RNTI selection when entering Connected mode (FDD only) ...................................................................36 Discontinuous Reception for Paging...........................................................................................................37 Discontinuous Reception for MBMS ..........................................................................................................38 Discontinuous Reception for MCCH.....................................................................................................38 Discontinuous Reception via MICH.................................................................................................38 Discontinuous Reception via MODIFIED SERVICES INFORMATION..........................................39 Discontinuous Reception for MTCH .....................................................................................................39
8a 9 10
MBMS Notification ..........................................................................................................................39 Void .................................................................................................................................................39 Void .................................................................................................................................................40 Change history ...........................................................................................40
Annex A (informative):
3GPP
Release 7
3GPP TS 25.304 V7.8.0 (2009-09)
Foreword
This Technical Specification has been produced by the 3rd Generation Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document.
3GPP
Release 7
3GPP TS 25.304 V7.8.0 (2009-09)
Scope
The present document specifies the Access Stratum (AS) part of the Idle Mode procedures applicable to a UE. The nonaccess stratum (NAS) part of Idle mode procedures and processes is specified in [5]. The present document also specifies cell selection and reselection processes applicable to UEs in connected mode. Invocation of these processes is described in [4]. The present document specifies the model for the functional division between the NAS and AS in a UE. The present document applies to all UEs that support at least UTRA, including multi-RAT UEs as described in 3GPP specifications, in the following cases: When the UE is camped on a UTRA cell; When the UE is searching for a cell to camp on; The details for those cases are described in the specifications of the other RAT.
NOTE:
The present document presents also examples of inter-layer procedures related to the idle mode processes and describes idle mode functionality of a dual RAT UTRA/GSM UE. The present document also specifies how idle-mode and reselection procedures are affected by the provision of MBMS services.
References
References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] 3GPP TS 43.022: "Functions related to Mobile Station in idle mode and group receive mode". 3GPP TS 25.301: "Radio Interface Protocol Architecture". 3GPP TS 25.303: "Interlayer Procedures in Connected Mode". 3GPP TS 25.331: "Radio Resource Control (RRC); protocol specification". 3GPP TS 23.122: "NAS functions related to Mobile Station (MS) in idle mode ". 3GPP TR 25.922: "Radio Resource Management Strategies". 3GPP TS 25.211: "Physical channels and mapping of transport channels onto physical channels (FDD)". 3GPP TS 25.221: "Physical channels and mapping of transport channels onto physical channels (TDD)". 3GPP TS 22.011: "Service accessibility". 3GPP TS 25.133: "Requirements for Support of Radio Resource Management (FDD)". 3GPP TS 25.123: "Requirements for Support of Radio Resource Management (TDD)".
The following documents contain provisions which, through reference in this text, constitute provisions of the present document.
3GPP
Release 7
3GPP TS 25.304 V7.8.0 (2009-09)
[12] [13] [14] [15] [16] [17]
3GPP TR 21.905: "Vocabulary for 3GPP Specifications". 3GPP TS 45.008: "Radio subsystem link control". 3GPP TS 25.214: "Physical layer procedures (FDD)". 3GPP TS 25.224: "Physical Layer Procedures (TDD)". 3GPP TS 24.008: "Mobile radio interface layer 3 specification, Core Network Protocols - Stage 3". 3GPP TS 25.346: "Introduction of the Multimedia Broadcast Multicast Service (MBMS) in the Radio Access Network (Stage-2)".
3
3.1
Definitions and abbreviations

Definitions
For the purposes of the present document, the following definitions and the definitions in [12] apply. Acceptable Cell: A cell that satisfies certain conditions as specified in 4.3. A UE can always attempt emergency calls on an acceptable cell. Available PLMN: A PLMN for which the UE has found at least one cell and read its PLMN identity. Barred Cell: A cell a UE is not allowed to camp on. Camped on a cell: UE has completed the cell selection/reselection process and has chosen a cell. The UE monitors system information and (in most cases) paging information. Camped on any cell: UE is in idle mode and has completed the cell selection/reselection process and has chosen a cell irrespective of PLMN identity. Camped on MBSFN cluster: UE has completed the MBSFN Cluster selection/reselection process and has chosen a MBSFN Cluster. The UE monitors system information and receives notifications for MBMS services and possibly receives a MBMS service. DRX cycle: Individual time interval between monitoring Paging Occasion for a specific UE. EHPLMN: Any of the PLMN entries contained in the Equivalent HPLMN list stored on the USIM [5]. Equivalent PLMN list: List of PLMNs considered as equivalent by the UE for cell selection, cell reselection , MBSFN Cluster selection MBSFN Cluster reselection and handover according to the information provided by the NAS. Home PLMN: A PLMN where the Mobile Country Code (MCC) and Mobile Network Code (MNC) of the PLMN identity are the same as the MCC and MNC of the IMSI. Location Registration (LR): UE registers its presence in a registration area, for instance regularly or when entering a new registration area. Maximum DRX cycle: Time interval for the longest possible DRX cycle in a cell. MBMS Activated Service: An MBMS service that the UE has joined (multicast) or is interested in (broadcast). MBMS Preferred Layer (PL): A frequency layer that is indicated by the UTRAN to be preferred for camping for MBMS purposes. MBSFN cluster: Set of cells operating in MBSFN mode providing only MBMS service in PtM mode and seen as one cell by a UE. MBSFN mode: In order to achieve higher spectral efficiency synchronized cells operate in MBSFN mode which implies that they transmit exactly the same content over an area that is seen as one MBSFN cell by the UE. Paging Block Periodicity (PBP): Period of the occurrence of Paging Blocks. (For FDD, PBP = 1).
3GPP
Release 7
3GPP TS 25.304 V7.8.0 (2009-09)
Paging Message Receiving Occasion (TDD only): The frame where the UE receives actual paging message. Paging occasion: (FDD) The SFN of the PICH frame where the UE monitors its paging indicator (i.e. the SFN of the PCCPCH frame in which the PICH frame begins). (TDD) The paging block, which consists of several frames. The value of Paging Occasion is equal to the first frame of the Paging Block. Process: A local action in the UE invoked by a RRC procedure or an Idle Mode procedure. Radio Access Mode: Radio access mode of the cell, FDD or TDD. Radio Access Technology: Type of technology used for radio access, for instance UTRA or GSM. Registered PLMN: This is the PLMN on which certain Location Registration outcomes have occurred [5]. Registration Area: (NAS) registration area is an area in which the UE may roam without a need to perform location registration, which is a NAS procedure. Reserved Cell: A cell on which camping is not allowed, except for particular UEs, if so indicated in the system information. Restricted Cell: A cell on which camping is allowed, but access attempts are disallowed for UEs whose access classes are indicated as barred. Selected PLMN: This is the PLMN that has been selected by the NAS, either manually or automatically. Serving cell: The cell on which the UE is camped. Strongest cell: The cell on a particular carrier that is considered strongest according to the layer 1 cell search procedure [14][15]. As the details of the layer 1 cell search are implementation dependent, the precise definition of 'strongest cell' is also implementation dependent. Suitable Cell: This is a cell on which an UE may camp. For a UTRA cell, the criteria are defined in subclause 4.3, and for a GSM cell the criteria are defined in [1].
3.2
AS BCCH CM CN DRX DSCH FDD GC GPRS GSM HCS IMSI MBMS MBSFN MCC MCCH MICH MM MNC MSCH MTCH NAS NI PCH
Abbreviations
Access Stratum Broadcast Control Channel Connection Management Core Network Discontinuous Reception Downlink Shared Channel Frequency Division Duplex General Control (SAP) General Packet Radio Service Global System for Mobile Communications Hierarchical Cell Structure International Mobile Subscriber Identity Multimedia Broadcast-Multicast Service MBMS over a Single Frequency Network Mobile Country Code MBMS point-to-multipoint Control Channel MBMS notification Indicator Channel Mobility Management Mobile Network Code MBMS point-to-multipoint Scheduling Channel MBMS point-to-multipoint Traffic Channel Non-Access Stratum (MBMS) Notification Indicator Paging Channel
For the purposes of the present document, the following abbreviations apply:
3GPP
Release 7
3GPP TS 25.304 V7.8.0 (2009-09)
PI PICH PLMN RAT RRC SAP TDD TMGI UE UMTS UTRA UTRAN
Page Indicator Page Indication Channel Public Land Mobile Network Radio Access Technology Radio Resource Control Service Access Point Time Division Duplex Temporary Mobile Group Identity User Equipment Universal Mobile Telecommunications System UMTS Terrestrial Radio Access UMTS Terrestrial Radio Access Network
3GPP
Release 7
10
3GPP TS 25.304 V7.8.0 (2009-09)
4
4.1
General description of Idle mode

Overview
When a UE is switched on, a public land mobile network (PLMN) is selected and the UE searches for a suitable cell of this PLMN to camp on. Criteria for cell selection and cell re-selection between radio access technologies (RATs) described in this document only consider radio criteria. In addition to RAT, the PLMN type may differ as well. In this specification, the term PLMN is used as a generic term covering both GSM MAP and ANSI-41 type of PLMNs. According to the type of PLMN, the way to identify it can be different. If the PLMN type is GSM, the PLMN is identified by 'PLMN identity' and if the PLMN type is ANSI-41, the PLMN is identified by 'SID' The NAS shall provide a list of equivalent PLMNs, if available, that the AS shall use for cell selection and cell reselection. The UE searches for a suitable cell of the selected PLMN and chooses that cell to provide available services, and tunes to its control channel. This choosing is known as "camping on the cell". The UE will, if necessary, then register its presence, by means of a NAS registration procedure, in the registration area of the chosen cell and as outcome of a successful Location Registration the selected PLMN becomes the registered PLMN [5]. If the UE finds a more suitable cell, it reselects onto that cell and camps on it. If the new cell is in a different registration area, location registration is performed. If necessary, the UE shall search for higher priority PLMNs at regular time intervals as described in [9] and search for a suitable cell if another PLMN has been selected by NAS. NOTE: For RRC connected mode the requirements for the search for higher priority PLMNs are defined in [4]. If the UE loses coverage of the registered PLMN, either a new PLMN is selected automatically (automatic mode), or an indication of which PLMNs are available is given to the user, so that a manual selection can be made (manual mode). Registration is not performed by UEs only capable of services that need no registration. The purpose of camping on a cell in idle mode is fourfold: a) It enables the UE to receive system information from the PLMN. b) When registered and if the UE wishes to establish an RRC connection, it can do this by initially accessing the network on the control channel of the cell on which it is camped. c) If the PLMN receives a call for the registered UE, it knows (in most cases) the registration area of the cell in which the UE is camped. It can then send a "paging" message for the UE on control channels of all the cells in the registration area. The UE will then receive the paging message because it is tuned to the control channel of a cell in that registration area and the UE can respond on that control channel. d) It enables the UE to receive cell broadcast services. If the UE is unable to find a suitable cell to camp on, or the USIM is not inserted, or if the location registration failed (except for LR rejected with cause #12, cause #14 or cause #15, see [5] and [16]), it attempts to camp on a cell irrespective of the PLMN identity, and enters a "limited service" state in which it can only attempt to make emergency calls. The idle mode tasks can be subdivided into three processes: PLMN selection; Cell selection and reselection; Location registration.
The relationship between these processes is illustrated in Figure 1.
3GPP
Release 7
11
3GPP TS 25.304 V7.8.0 (2009-09)
Manual Mode
Automatic mode
PLMN Selection
Indication to user Location Regist ration response PLMNs available
PLMN selected NAS Control
Cell Selection and Reselection

Radio measurem ents
Registration Area changes CM requests
Location Registration
Figure 1: Overall Idle Mode process
4.2
Functional division between AS and NAS in Idle mode
Table 1 presents the functional division between UE non-access stratum (NAS) and UE access stratum (AS) in idle mode. The NAS part is specified in [5] and the AS part in the present document. Examples of different idle mode procedures are presented in Clause 10.
3GPP
Release 7
12
3GPP TS 25.304 V7.8.0 (2009-09)
Table 1: Functional division between AS and NAS in idle mode

Idle Mode Process PLMN Selection UE Non-Access Stratum Maintain the list of allowed PLMN types. It can be GSM-MAP only, ANSI-41 only or both. Maintain a list of PLMNs in priority order according to [5]. Select a PLMN using automatic or manual mode as specified in [5] and request AS to select a cell belonging to this PLMN. For each PLMN, associated RAT(s) may be set. Evaluate reports of available PLMNs from AS for PLMN selection. Maintain a list of equivalent PLMN identities. Report available PLMNs with associated PLMN type and RAT to NAS on request from NAS or autonomously. It shall respect allowed PLMN types indications from NAS. Perform measurements needed to support cell selection. Detect and synchronise to a broadcast channel. Receive and handle broadcast information. Forward NAS system information to NAS. Search for a suitable cell. The cells broadcast their 'PLMN identity' (GSM-MAP) or 'SID' in the system information. Respond to NAS whether such cell is found or not. If associated RATs is (are) set for the PLMN, perform the search in this (these) RAT(s) and other RATs for that PLMN as specified in [5]. If such a cell is found, the cell is selected to camp on. Perform measurements needed to support cell reselection. Detect and synchronise to a broadcast channel. Receive and handle broadcast information. Forward NAS system information to NAS. Change cell if a more suitable cell is found. Report registration area information to NAS. UE Access Stratum Search for available PLMNs. If associated RAT(s) is (are) set for the PLMN, search in this (these) RAT(s) and other RAT(s) for that PLMN as specified in [5]. Perform measurements to support PLMN selection. Synchronise to a broadcast channel to identify found PLMNs.
Cell Selection
Control cell selection for example by indicating RAT(s) associated with the selected PLMN to be used initially in the search of a cell in the cell selection. NAS is also maintaining lists of forbidden registration areas.
Cell Reselection
Control cell reselection by for example, maintaining lists of forbidden registration areas. Maintain a list of equivalent PLMN identities and provide the list to AS. Maintain a list of forbidden LAs and provide the list to AS
Location registration
Register the UE as active after power on. Register the UE's presence in a registration area, for instance regularly or when entering a new registration area. Maintain lists of forbidden LAs. Deregister UE when shutting down.
3GPP
Release 7 MBMS
13 Maintain priority information for various services and participate in service selection. Indicate to AS if an offered session has previously been received.
3GPP TS 25.304 V7.8.0 (2009-09) Maintain a list of TMGIs of activated services. Notify NAS of service availability and request NAS to prioritise in case of service conflicts. Report to NAS when an activated service requires action. Receive and handle the MCCH and MTCH, and, if applicable, the MSCH and MICH.
4.3
Service type in Idle and Connected Mode
This clause defines the level of service that may be provided by the network to a UE in Idle mode and Connected Mode. The action of camping on a cell is necessary to get access to some services. Three levels of services are defined for UE: Limited service (emergency calls on an acceptable cell) Normal service (for public use on a suitable cell) Operator service (for operators only on a reserved cell)
Furthermore, the cells are categorised according to which services they offer: acceptable cell: An "acceptable cell" is a cell on which the UE may camp to obtain limited service (originate emergency calls). Such a cell shall fulfil the following requirements, which is the minimum set of requirements to initiate an emergency call in a UTRAN network: The cell is not barred, see subclause 5.3.1.1; The cell selection criteria are fulfilled, see subclause 5.2.3.1.2;
suitable cell: A "suitable cell" is a cell on which the UE may camp on to obtain normal service. Such a cell shall fulfil all the following requirements. The cell shall be part of either: the selected PLMN, or: the registered PLMN, or: a PLMN of the Equivalent PLMN list according to the latest information provided by the NAS. The cell is not barred, see subclause 5.3.1.1; The cell is part of at least one LA that is not part of the list of "forbidden LAs for roaming" [9], which belongs to a PLMN that fulfills the first bullet above; The cell selection criteria are fulfilled, see subclause 5.2.3.1.2.
If the IE Multiple PLMN List [4] is broadcast in the cell, the cell is considered to be part of all LAs with LAIs constructed from the PLMN identities in the Multiple PLMN List and the LAC broadcast in the cell. barred cell: A cell is barred if it is so indicated in the system information [4].
3GPP
Release 7
14
3GPP TS 25.304 V7.8.0 (2009-09)
reserved cell: A cell is reserved if it is so indicated in system information [4]. Exceptions to these definitions are applicable for UEs camped on a cell that belongs to a LA that is forbidden for regional provision of service, and during emergency calls. A cell that belongs to a LA that is forbidden for regional provision service ([5], [16]) is suitable but provides only limited service. If a UE has an ongoing emergency call, all acceptable cells of that PLMN are treated as suitable for cell reselection for the duration of the emergency call. suitable MBSFN cluster: A cell is part of an MBSFN cluster if it is indicated in system information [4]. An MBSFN cluster provides exclusively MBMS services. A suitable MBSFN cluster shall fulfil all the following requirements: For FDD and 3.84/7.68 Mcps TDD the MBSFN cluster shall be part of either: the registered PLMN, or: a PLMN of the Equivalent PLMN list The MBSFN cluster shall be indicated as: providing MBSFN only service
For FDD and 3.84/7.68 Mcps TDD MBSFN cluster selection/reselection process for MBSFN clusters operating on the same frequency shall be based on reception quality. Details of the process are not specified.
5
5.1
5.1.1
Process and procedure descriptions

PLMN selection
General
In the UE, the AS shall report available PLMNs to the NAS on request from the NAS or autonomously. UE shall maintain a list of allowed PLMN types. The allowed PLMN type can be GSM-MAP only, ANSI-41 only or both. During PLMN selection, based on the list of allowed PLMN types and a list of PLMN identities in priority order, the particular PLMN may be selected either automatically or manually. Each PLMN in the list of PLMN identities can be identified by either 'PLMN identity' (GSM-MAP) or 'SID'. In the system information on the broadcast channel, the UE can receive a 'PLMN identity' (GSM-MAP) or a 'SID' or a 'PLMN identity' (GSM-MAP) and a 'SID', in a given cell. For a given cell, the UE might receive several 'PLMN identities' from the system information on the broadcast channel. The result of the PLMN selection is an identifier of the selected PLMN, the choice being based on the allowed PLMN types, UE capability or other factors. This identifier is one of either 'PLMN identity' for GSM-MAP type of PLMNs or 'SID' for ANSI-41 type of PLMNs. In case that the list of allowed PLMN types includes GSM-MAP, the non-access part of the PLMN selection process is specified in [5]. In the case that list of allowed PLMN types includes ANSI-41, the non-access stratum part of the PLMN selection is specified in TIA/EIA/IS-2000.5 and TIA/EIA/IS-707.
5.1.2
5.1.2.1
Support for PLMN Selection

General
On request of the NAS the AS should perform a search for available PLMNs and report them to NAS.
3GPP
Release 7
15
3GPP TS 25.304 V7.8.0 (2009-09)
5.1.2.2
UTRA case
The UE shall scan all RF channels in the UTRA bands according to its capabilities to find available PLMNs. On each carrier, the UE shall search for the strongest cell and read its system information, in order to find out which PLMN the cell belongs to. If the UE can read one or several PLMN identities in the strongest cell, each found PLMN (see the PLMN reading in [4]) shall be reported to the NAS as a high quality PLMN (but without the RSCP value), provided that the following high quality criterion is fulfilled: 1. For an FDD cell, the measured primary CPICH RSCP value shall be greater than or equal to -95 dBm. 2. For a TDD cell, the measured P-CCPCH RSCP shall be greater than or equal to -84 dBm. Found PLMNs that do not satisfy the high quality criterion, but for which the UE has been able to read the PLMN identities are reported to the NAS together with the CPICH RSCP value for UTRA FDD cells and P-CCPCH RSCP for UTRA TDD cells. The quality measure reported by the UE to NAS shall be the same for each PLMN found in one cell. The search for PLMNs on the rest of the carriers may be stopped on request of the NAS. The UE may optimise this search by using stored information of carrier frequencies and optionally also information on cell parameters, e.g. scrambling codes, from previously received measurement control information elements. Once the UE has selected a PLMN, the cell selection procedure shall be performed in order to select a suitable cell of that PLMN to camp on.
5.1.2.3
GSM case
Support for network selection in GSM is described in [1].
5.2
5.2.1
Cell selection and reselection in idle mode

Introduction
As stated in clause 1, the present document applies to UEs that support at least UTRA. Different types of measurements are used in different RATs and modes for the cell selection and reselection. The performance requirements for the measurements are specified in [10] and [11]. The NAS can control the RAT(s) in which the cell selection should be performed, for instance by indicating RAT(s) associated with the selected PLMN, and by maintaining a list of forbidden registration area(s) and a list of equivalent PLMNs. The UE shall select a suitable cell and the radio access mode based on idle mode measurements and cell selection criteria. In order to speed up the cell selection process, stored information for several RATs may be available in the UE. When camped on a cell, the UE shall regularly search for a better cell according to the cell reselection criteria. If a better cell is found, that cell is selected. The change of cell may imply a change of RAT. Details on performance requirements for cell reselection can be found in [10] and [11]. The NAS is informed if the cell selection and reselection results in changes in the received system information. For normal service, the UE has to camp on a suitable cell, tune to that cell's control channel(s) so that the UE can: Receive system information from the PLMN; Receive registration area information from the PLMN, e.g., location area and routing area; and Receive other AS and NAS Information;
If registered: receive paging and notification messages from the PLMN; and initiate call setup for outgoing calls or other actions from the UE.
3GPP
Release 7
16
3GPP TS 25.304 V7.8.0 (2009-09)
5.2.2
States and state transitions in Idle Mode
Figure 2 shows the states and procedures in Idle Mode.

go here w henever a new PLMN is selected no cell inf ormation stored f or the PLMN
cell inf ormation stored f or the PLMN Stored inf ormation Cell Se lection no suitable cell found
no suitable cell found
Init ial Cell Se lection
suitable cell f ound
suitable cell f ound no suitable cell f ound
Cell Selection w hen leaving connected mode
suitable cell f ound
Camped normally
NA S indicates that registration on selected PL MN is rejected (except w ith cause #12, #14 or #15 [5][16])
return to idle mode
leave idle mode
trigger suitable cell f ound
Connected mode
Cell Reselection Evaluation Process
no suitable cell f ound go here w hen no US IM in the UE
no acceptable cell f ound
Any Cell Selection
US IM inserted acceptable cell f ound Cell Se lection w hen leaving connected mode
acceptable cell f ound
Camped on any cell
suitable cell found
return to idle mode
leave idle mode
trigger acceptable cell found
Connected mode (Emergency calls only)
no acceptable cell f ound
Figure 2: Idle Mode Cell Selection and Reselection In any state, a new PLMN selection causes an exit to number 1
5.2.2.1
Cell Selection process overview
Whenever a PLMN has been selected by NAS, the UE shall attempt to find a suitable cell to camp on.
3GPP
Release 7
17
3GPP TS 25.304 V7.8.0 (2009-09)
The NAS may control the cell selection by: providing information on RAT(s) associated with the selected PLMN; maintaining lists of forbidden registration areas; providing a list of equivalent PLMNs;
One or several RATs may be associated with the selected PLMN. In [5] it is specified which RAT a UE shall select to search for a suitable cell of the selected PLMN. The AS shall attempt to find a suitable cell to camp on as specified in clause 5.2.3. When the MBMS frequency layer dispersion is triggered, the UE actions are specified in [4]. If a suitable cell is found, the UE shall select this cell to camp on, and report this event to NAS so that the necessary NAS registration procedures can be performed. When the registration is successful, the UE enters in state Camped normally in order to obtain normal service. If the UE is unable to find any suitable cell of selected PLMN the UE shall enter the Any cell selection state.
5.2.2.2
Camped normally state overview
In this state, the UE obtains normal service and performs the tasks specified in 5.2.5. If after a Cell reselection evaluation process a better cell is found, the Cell reselection procedure is performed. If no suitable cell is found, the UE shall enter the state Any cell selection. If a necessary NAS registration is rejected, the UE shall enter the Any cell selection state, except if the LR is rejected with cause #12, cause #14 or cause #15. In this case the UE shall behave as specified in [5] and [16]. When UE leaves idle mode in order to enter the state Connected mode, the UE shall attempt to access the current serving cell. If the access attempt to the serving cell fails, the UE shall use the Cell reselection evaluation procedure.
5.2.2.3
Connected mode State overview
The procedures in Connected mode state are specified in [4] When returning to idle mode, the UE shall use the procedure Cell selection when leaving connected mode in order to find a suitable cell to camp on and enter state Camped normally. If a suitable cell is found, then the AS reports this event to NAS to be capable to perform necessary NAS registration procedures. If no suitable cell is found, the Stored information cell selection procedure shall be used. If no suitable cell is found in cell reselection evaluation process, the UE enters the state Any cell selection.
5.2.2.4
Any cell selection State overview
In this state the UE performs the tasks specified in subclause 5.2.8 The state Any cell selection is also entered if the NAS indicates that a location registration is rejected except if the LR is rejected with cause #12, cause #14 or cause #15, see [5], or if there is no USIM in the UE. If the UE received an LR reject with cause #12, cause #14 or cause #15, the UE shall behave as specified in [5] and [16]. If an acceptable cell is found, the UE shall inform the NAS and camp on this cell and obtain limited service, state Camped on any cell. The subsequent actions of the NAS regarding the PLMN selection are specified in [5].
5.2.2.5
Camped on any cell State overview
In this state the UE obtains limited service and shall behave as specified in subclause 5.2.9. The UE shall regularly attempt to find a suitable cell, trying all RATs that are supported by the UE. If a suitable cell is found, this causes an exit to number 2 in figure 2.
3GPP
Release 7
18
3GPP TS 25.304 V7.8.0 (2009-09)
NOTE:
The 'PLMN selection' process may select a new PLMN at any time in idle mode, which in Figure 2 causes an exit to number 1.
5.2.3
5.2.3.1
5.2.3.1.1
Cell Selection Process

UTRA case
Description
The UE shall use one of the following two search procedures: a) Initial Cell Selection This procedure requires no prior knowledge of which RF channels are UTRA carriers. The UE shall scan all RF channels in the UTRA bands according to its capabilities to find a suitable cell. On each carrier, the UE need only search for the strongest cell. Once a suitable cell is found this cell shall be selected. b) Stored Information Cell Selection This procedure requires stored information of carrier frequencies and optionally also information on cell parameters, e.g. scrambling codes, from previously received measurement control information elements. Once the UE has found a suitable cell the UE shall select it. If no suitable cell is found the Initial cell selection procedure shall be started.
5.2.3.1.2
Criteria
The cell selection criterion S is fulfilled when:
for FDD cells: for TDD cells:

Where:
Srxlev > 0 AND Squal > 0 Srxlev > 0
Squal = Q qualm eas (Q qualm in + Q qualm inO ffset) Srxlev = Q rxlevm eas (Q rxlevm in + Q rxlevm inO ffset) Pcom pensation
Where: the signalled values QqualminOffset and QrxlevminOffset are only applied when a cell is evaluated for cell selection as a result of a periodic search for a higher priority PLMN while camped normally in a VPLMN [5]. During this periodic search for higher priority PLMN the UE may check the S criteria of a cell using parameter values stored from a different cell of this higher priority PLMN.
3GPP
Release 7 Squal Srxlev Qqualmeas
19
3GPP TS 25.304 V7.8.0 (2009-09)
Qrxlevmeas Qqualmin QqualminOffset Qrxlevmin QrxlevminOffset Pcompensation UE_TXPWR_MAX_RACH P_MAX
Cell Selection quality value (dB) Applicable only for FDD cells. Cell Selection RX level value (dB) Measured cell quality value. The quality of the received signal expressed in CPICH Ec/N0 (dB) for FDD cells. CPICH Ec/N0 shall be averaged as specified in [10]. Applicable only for FDD cells. Measured cell RX level value. This is received signal, CPICH RSCP for FDD cells (dBm) and P-CCPCH RSCP for TDD cells (dBm). Minimum required quality level in the cell (dB). Applicable only for FDD cells. Offset to the signalled Qqualmin taken into account in the Squal evaluation as a result of a periodic search for a higher priority PLMN while camped normally in a VPLMN [5] Minimum required RX level in the cell (dBm) Offset to the signalled Qrxlevmin taken into account in the Srxlev evaluation as a result of a periodic search for a higher priority PLMN while camped normally in a VPLMN [5] max(UE_TXPWR_MAX_RACH P_MAX, 0) (dB) Maximum TX power level an UE may use when accessing the cell on RACH (read in system information) (dBm) Maximum RF output power of the UE (dBm)
5.2.3.2
GSM case
The cell selection criteria and procedures in GSM are specified in [1].
5.2.4
Void
5.2.5
5.2.5.1
Camped Normally State

UTRA case
When camped normally, the UE shall perform the following tasks: select and monitor the indicated PICH and PCH of the cell as specified in clause 8 according to information sent in system information; monitor relevant System Information. This is specified in [4]; perform necessary measurements for the cell reselection evaluation procedure; execute the cell reselection evaluation process on the following occasions/triggers: 1) UE internal triggers, so as to meet performance as specified in [10] and [11]; 2) When information on the BCCH used for the cell reselection evaluation procedure has been modified If the UE supports MBMS and MBMS is active in the cell and the UE is permitted to receive MBMS services in the cell, the UE shall perform MBMS tasks as specified in subclause 6.3.
5.2.5.2
GSM case
The Camped Normally State is specified in [1].
5.2.6
5.2.6.1

UTRA case
The cell reselection process is specified in the following sub-clauses:
3GPP
Release 7
20
3GPP TS 25.304 V7.8.0 (2009-09)
5.2.6.1.0
Use of MBMS PL
In the cell reselection process, an MBMS PL shall only be applicable while the UE is receiving an MBMS session from one or more of the ongoing activated MBMS services for which this PL is indicated.
5.2.6.1.1
Measurement rules for cell re-selection when HCS is not used
The measurement rules below apply in Idle, URA_PCH, CELL_PCH states. In CELL_FACH state the UE is required to perform measurements on all intra-frequency, inter-frequency and inter-RAT cells listed in system information according to requirements specified in [10]. In Idle, URA_PCH, CELL_PCH and CELL_FACH states the UE shall only consider those cells the UE is mandated to measure according to the measurement rules below as measured cells in the cell reselection criteria (subclause 5.2.6.1.4). If the system information broadcast in the serving cell indicates that HCS is not used, then for intra-frequency and interfrequency measurements and inter-RAT measurements, the UE shall: use Squal for FDD cells and Srxlev for TDD for Sx, and apply the following rules.
1. If Sx > Sintrasearch, UE may choose to not perform intra-frequency measurements. If Sx <= Sintrasearch, perform intra-frequency measurements. If Sintrasearch, is not sent for serving cell, perform intra-frequency measurements. 2. If Sx > Sintersearch and MBMS PL has not been indicated, and Srxlev > SsearchHCS if SsearchHCS is signalled, UE may choose to not perform inter-frequency measurements. If Sx > Sintersearchand MBMS PL has been indicated and the serving cell belongs to the MBMS PL, and Srxlev > SsearchHCS if SsearchHCS is signalled, UE may choose to not perform inter-frequency measurements. If Sx > Sintersearch, and MBMS PL has been indicated and the serving cell does not belong to the MBMS PL, and Srxlev > SsearchHCS if SsearchHCS is signalled, UE shall at least perform inter-frequency measurements on the MBMS PL. If Sx <= Sintersearch, or Srxlev <= SsearchHCS if SsearchHCS is signalled, perform inter-frequency measurements. If Sintersearch, is not sent for serving cell, perform inter-frequency measurements. 3. If Sx > SsearchRAT m, and Srxlev > SHCS,RATm if SHCS,RATm is signalled, UE may choose to not perform measurements on cells of RAT "m". If Sx <= SsearchRAT m, or Srxlev <= SHCS,RATm if SHCS,RATm is signalled, perform measurements on cells of RAT "m". If SsearchRAT m, is not sent for serving cell, perform measurements on cells of RAT "m". If HCS is not used and if Slimit,SearchRATm is sent for serving cell, UE shall ignore it. NOTE: The presence of SsearchHCS and SHCS,RATm thresholds in system information are used to avoid introducing new parameters to system information and their presence does not imply that HCS is used.
5.2.6.1.1a
High mobility state when HCS is not used
High-mobility, as applied in HCS case, is also applicable in non-HCS if the parameters non-HCS_ TCRmax, nonHCS_NCR and non-HCS_TCRmaxhyst are sent on the system information broadcast. If in non-HCS environment the number of cell reselections during time period non-HCS_TCRmax exceeds non-HCS_NCR, or if the network (via RRC signalling) has ordered the UE to consider itself to be in high-mobility state, then highmobility state has been detected. When the number of cell reselections during time period non-HCS_TCRmax no longer exceeds non-HCS_NCR, the UE shall: continue in high-mobility state. if the criteria for entering high mobility is not detected during time period non-HCS-TCrmaxHyst: exit high-mobility.
If the UE is in non-HCS environment and in high-mobility state, the UE shall apply the speed dependent scaling rules as defined in subclause 5.2.6.1.4.
3GPP
Release 7
21
3GPP TS 25.304 V7.8.0 (2009-09)
5.2.6.1.2
Measurement rules for cell re-selection when HCS is used
The measurement rules below apply in Idle, URA_PCH, CELL_PCH states. In CELL_FACH state the UE is required to perform measurements on all intra-frequency, inter-frequency and inter-RAT cells listed in system information according to requirements specified in [10]. In Idle, URA_PCH, CELL_PCH and CELL_FACH states the UE shall only consider those cells the UE is mandated to measure according to the measurement rules below as measured cells in the cell reselection criteria (subclause 5.2.6.1.4). If the system information broadcast in the serving cell indicates that HCS is used, then for intra-frequency and interfrequency measurements, the UE shall: use HCS priority1 as the HCS priority broadcast in the system information and apply the following rule: IF an MBMS PL is used THEN If the UE is in HCS low mobility state, for serving cell and neighbour cells belonging to the MBMS PL set the HCS priority = HCS priority1 + HCS_OFFmbms. If the UE is in HCS high mobility state, for serving cell and neighbour cells belonging to the MBMS PL set the HCS priority = HCS priority1. for serving cell and neighbour cells not belonging to the MBMS PL, set the HCS priority = HCS priority1.
IF an MBMS PL is not used THEN For serving cell and all neighbour cells set HCS priority = HCS priority1 Then apply this to the following:
1. For intra-frequency and inter-frequency measurement rules for UEs not in high-mobility use Squal for FDD cells and Srxlev for TDD cells for Sx and apply the following rules. IF (Srxlevs <= SsearchHCS) or (if FDD and Sx <= Sintersearch) THEN measure on all intra-frequency and inter-frequency cells. ELSE IF (Sx > Sintrasearch) THEN measure on all intra-frequency and inter-frequency cells, which have higher HCS priority level than the serving cell ELSE measure on all intra-frequency and inter-frequency cells, which have equal or higher HCS priority level than the serving cell ENDIF IF (Sintrasearch is not sent for the serving cell) THEN measure on all intra-frequency cells. Fast-moving UEs may also use this rule. measure on all inter-frequency cells, which have higher HCS priority level than the serving cell unless measurement rules for fast-moving UEs are triggered. ENDIF ENDIF If HCS is used and if SsearchHCS or Sintersearch (in FDD) are not sent for the serving cell, UE shall: measure on all intra-frequency and inter-frequency cells.
3GPP
Release 7
22
3GPP TS 25.304 V7.8.0 (2009-09)
2. For intra-frequency and inter-frequency measurement rules for fast-moving UEs: If the number of cell reselections during time period TCRmax exceeds NCR, or if the network (via RRC signalling) has ordered the UE to consider itself in high mobility state, then high-mobility has been detected. In this highmobility state, UE shall IF (Srxlevs <= SsearchHCS) or (if FDD and Sx <= Sintersearch), or SsearchHCS or Sintersearch (in FDD) are not sent for the serving cell THEN measure on all intra-frequency and inter-frequency cells. ELSE measure intra-frequency and inter-frequency neighbouring cells, which have equal or lower HCS priority than serving cell.
ENDIF
When the number of cell reselections during time period TCRmax no longer exceeds NCR, UE shall continue these measurements during time period TCrmaxHyst if the criteria for entering high mobility is not detected during time period TCrmaxHyst: exit high-mobility.
When serving cell belongs to a hierarchical cell structure, the UE shall follow these rules for Inter-RAT measurements: 1. Inter-RAT threshold-based measurement rules for UEs not in high-mobility use Squal for FDD cells and Srxlev for TDD cells for Sx and apply the following rules. IF (Srxlevs <= SHCS,RATm) or (if FDD and Squal <= SSearchRATm) THEN UE shall measure on all inter-RATm cells. ELSE IF (Sx > Slimit,SearchRATm) THEN UE may choose to not measure neighbouring cells in RAT "m". ELSE UE shall measure on all neighbouring cells in RAT "m", which have equal or higher HCS priority level than the serving cell ENDIF ENDIF If HCS is used and if SHCS,RATm is not sent for the serving cell, UE shall measure on all inter-RATm cells. 2. Inter-RAT measurement rules for fast-moving UEs If the number of cell reselections during time period TCRmax exceeds NCR, or if the network (via RRC signalling) has ordered the UE to consider itself in high mobility state, then high-mobility has been detected. In this high-mobility state, UE shall IF (Srxlevs <= SHCS,RATm) or (if FDD and Squal <= SSearchRATm), or SHCS,RATm or SSearchRATm are not sent for the serving cell THEN UE shall measure on all inter-RATm cells.
ELSE
3GPP
Release 7
23
3GPP TS 25.304 V7.8.0 (2009-09)
measure the neighbouring cells in RAT "m", which have an equal or lower HCS priority than the serving cell
ENDIF
When the number of cell reselections during time interval TCRmax no longer exceeds NCR, UE shall continue these measurements during time period TCrmaxHyst if the criteria for entering high mobility is not detected during time period TCrmaxHyst exit high-mobility.
5.2.6.1.3
Highest ranked cells with cell reservations, access restrictions or unsuitable for normal camping
For the highest ranked cell (including serving cell) according to cell reselection criteria specified in subclause 5.2.6.1.4, the UE shall check if the access is restricted according to the rules in subclause 5.3.1.1. If that cell and other cells have to be excluded from the candidate list, as stated in subclause 5.3.1.1, the UE shall not consider these as candidates for cell reselection. This limitation is removed when the highest ranked cell changes. If the highest ranked cell is an intra-frequency or inter-frequency cell which is not suitable due to being part of the "list of forbidden LAs for roaming" or belonging to a PLMN which is not indicated as being equivalent to the registered PLMN, the UE shall not consider this cell and other cells on the same frequency, as candidates for reselection for a maximum of 300s. If the UE has to perform an any cell selection procedure any limitation shall be removed. If the highest ranked cell is an inter-RAT cell which is not suitable due to being part of the "list of forbidden LAs for roaming" or belonging to a PLMN which is not indicated as being equivalent to the registered PLMN, the UE shall not consider this cell as a candidate for reselection for a maximum of 300s. If the UE has to perform an any cell selection procedure any limitation shall be removed.
5.2.6.1.4
Cell Reselection Criteria
The following cell re-selection criteria are used for intra-frequency cells, inter-frequency cells and inter-RAT cells: The quality level threshold criterion H for hierarchical cell structures is used to determine whether prioritised ranking according to hierarchical cell re-selection rules shall apply, and is defined by:
Hs = Qmeas,s - Qhcss Hn = Qmeas,n - Qhcsn TOn * Ln
If it is indicated in system information that HCS is not used, the quality level threshold criterion H is not applied. The cell-ranking criterion R is defined by:
Rs = Qmeas,s + Qhysts + Qoffmbms Rn = Qmeas,n - Qoffsets,n + Qoffmbms - TOn * (1 Ln)

where:
3GPP
Release 7
24
3GPP TS 25.304 V7.8.0 (2009-09)
the signalled value Qoffmbms is only applied to those cells (serving or neighbouring) belonging to the MBMS PL where:
TOn = TEMP_OFFSETn * W(PENALTY_TIMEn Tn) Ln = 0 Ln = 1 W(x) = 0 W(x) = 1 if HCS_PRIOn = HCS_PRIOs if HCS_PRIOn <> HCS_PRIOs for x < 0 for x >= 0
TEMP_OFFSETn applies an offset to the H and R criteria for the duration of PENALTY_TIMEn after a timer Tn has started for that neighbouring cell. TEMP_OFFSETn and PENALTY_TIMEn are only applicable if the usage of HCS is indicated in system information. The timer Tn is implemented for each neighbouring cell. Tn shall be started from zero when one of the following conditions becomes true: if HCS_PRIOn <> HCS_PRIOs and Qmeas,n >= Qhcsn Or if HCS_PRIOn = HCS_PRIOs and for serving FDD and neighbour FDD cells if the quality measure for cell selection and reselection is set to CPICH RSCP in the serving cell, and: Qmeas,n > Qmeas,s + Qoffset1s,n for serving FDD and neighbour FDD cells if the quality measure for cell selection and reselection is set to CPICH Ec/No in the serving cell, and: Qmeas,n > Qmeas,s + Qoffset2s,n for all other serving and neighbour cells: Qmeas,n > Qmeas,s + Qoffset1s,n Tn for the associated neighbour cell shall be stopped as soon as any of the above conditions are no longer fulfilled. Any value calculated for TOn is valid only if the associated timer Tn is still running else TOn shall be set to zero. At cell-reselection, a timer Tn is stopped only if the corresponding cell is not a neighbour cell of the new serving cell, or if the criteria given above for starting timer Tn for the corresponding cell is no longer fulfilled with the parameters of the new serving cell. On cell re-selection, timer Tn shall be continued to be run for the corresponding cells but the criteria given above shall be evaluated with parameters broadcast in the new serving cell if the corresponding cells are neighbours of the new serving cell.
Sn Qmeas Cell Selection value of the neighbouring cell, (dB) Quality value. The quality value of the received signal derived from the averaged CPICH Ec/No or CPICH RSCP for FDD cells, from the averaged P-CCPCH RSCP for TDD cells and from the averaged received signal level for GSM cells. The averaging of these measurement quantities are performed as specified in [10] and [11]. For FDD cells, the measurement that is used to derive the quality value is set by the Cell_selection_and_reselection_quality_measure information element.
3GPP
Release 7
25
3GPP TS 25.304 V7.8.0 (2009-09)
Cell reselection parameters broadcast in system information are listed in subclause 5.2.6.1.5. The cell selection criterion S used for cell reselection is fulfilled when:
for FDD cells: for TDD cells: for GSM cells:

Where :
Srxlev > 0 AND Squal > 0 Srxlev > 0 Srxlev > 0
Squal = Qqualmeas Qqualmin Srxlev = Qrxlevmeas - Qrxlevmin - Pcompensation
Squal Srxlev Qqualmeas
Cell Selection quality value (dB) Applicable only for FDD cells. Cell Selection RX level value (dB) Measured cell quality value. The quality of the received signal expressed in CPICH Ec/N0 (dB) for FDD cells. CPICH Ec/N0 shall be averaged as specified in [10]. Applicable only for FDD cells. Measured cell RX level value. This is received signal, CPICH RSCP for FDD cells (dBm), P-CCPCH RSCP for TDD cells (dBm) and the averaged received signal level as specified in [10] for GSM cells (dBm). CPICH RSCP, P-CCPCH RSCP and the received signal level for GSM cells shall be averaged as specified in [10] and [11]. Minimum required quality level in the cell (dB). Applicable only for FDD cells. Minimum required RX level in the cell (dBm) max(UE_TXPWR_MAX_RACH P_MAX, 0) (dB) Maximum TX power level an UE may use when accessing the cell on RACH (read in system information) (dBm) Maximum RF output power of the UE (dBm)
Qrxlevmeas
Qqualmin Qrxlevmin Pcompensation UE_TXPWR_MAX_RACH P_MAX
If HCS is not used in the serving cell the UE shall perform ranking of all cells that fulfil the criterion S, among: all measured cells (see subclause 5.2.6.1.1).
If HCS is used in the serving cell, then from the cells that fulfil the criterion S, the UE shall perform ranking of all cells among 1. when in low-mobility (see subclause 5.2.6.1.2), all measured cells, that have the highest HCS_PRIO among those cells that fulfil the criterion H >= 0. all measured cells, not considering HCS priority levels, if no cell fulfil the criterion H >= 0.
2 when in high-mobility (see subclause 5.2.6.1.2), all measured cells, and among these cells: if there are cells with a lower HCS priority than the serving cell that fulfil the criterion H >= 0: from the cells that have a lower HCS priority than the serving cell, all cells that have the highest HCS_PRIO among those cells that fulfil the criterion H >=0;
else:
3GPP
Release 7
26
3GPP TS 25.304 V7.8.0 (2009-09)
if there are cells that fulfil the criterion H >= 0 with an HCS priority higher or equal to the HCS priority of the serving cell: from the cells that have an HCS priority higher or equal to the HCS priority of the serving cell, all cells that have the lowest HCS_PRIO among those cells that fulfil the criterion H >=0;
else all cells not considering HCS priority levels.
The cells shall be ranked according to the R criteria specified above, deriving Qmeas,n and Qmeas,s and calculating the R values using CPICH RSCP, P-CCPCH RSCP and the averaged received signal level as specified in [10] and [11] for FDD, TDD and GSM cells, respectively. The offset Qoffset1s,n is used for Qoffsets,n to calculate Rn, the hysteresis Qhyst1s is used for Qhysts to calculate Rs. For UE in RRC connected mode states CELL_PCH or URA_PCH the hysteresis Qhyst s takes the value Qhyst1s,PCH to calculate Rs, if provided in SIB4 [see 4]. For UE in RRC connected mode state CELL_FACH the hysteresis Qhyst s takes the value Qhyst1s,FACH to calculate Rs, if provided in SIB4 [see 4]. If the usage of HCS is indicated in system information, TEMP_OFFSET1n is used for TEMP_OFFSETn to calculate TOn. If it is indicated in system information that HCS is not used, TEMP_OFFSETn is not applied when calculating Rn. The best ranked cell is the cell with the highest R value. If a TDD or GSM cell is ranked as the best cell, then the UE shall perform cell re-selection to that TDD or GSM cell. If an FDD cell is ranked as the best cell and the quality measure for cell selection and re-selection is set to CPICH RSCP, the UE shall perform cell re-selection to that FDD cell. If this cell is found to be not suitable, the UE shall behave according to subclause 5.2.6.1.3. If an FDD cell is ranked as the best cell and the quality measure for cell selection and re-selection is set to CPICH Ec/No, the UE shall perform a second ranking of the FDD cells according to the R criteria specified above, but using the measurement quantity CPICH Ec/No for deriving the Qmeas,n and Qmeas,s and calculating the R values of the FDD cells. The offset Qoffset2s,n is used for Qoffsets,n to calculate Rn, the hysteresis Qhyst2s is used for Qhyst s to calculate Rs. For UE in RRC connected mode states CELL_PCH or URA_PCH the hysteresis Qhysts takes the value Qhyst2s,PCH to calculate Rs, if provided in SIB4 [see 4]. For UE in RRC connected mode state CELL_FACH the hysteresis Qhyst s takes the value Qhyst2s,FACH to calculate Rs, if provided in SIB4 [see 4]. If the usage of HCS is indicated in system information, TEMP_OFFSET2n is used to calculate TOn. If it is indicated in system information that HCS is not used, TEMP_OFFSETn is not applied when calculating Rn. Following this second ranking, the UE shall perform cell reselection to the best ranked FDD cell. If this cell is found to be not suitable, the UE shall behave according to subclause 5.2.6.1.3. In all cases, the UE shall reselect the new cell, only if the following conditions are met: the new cell is better ranked than the serving cell during a time interval Treselection. For UE in RRC connected mode states CELL_PCH or URA_PCH the interval Treselections,PCH applies, if provided in SIB4 [see 4], while for UE in RRC connected mode state CELL_FACH the interval Treselections,FACH applies, if provided in SIB4 [see 4]. For hierarchical cell structures when high mobility state has not been detected, if according to the HCS rules the serving cell is not ranked then all the ranked cells are considered to be better ranked than the serving cell. In case the UE reselects to a cell on an MBMS preferred frequency to receive an MBMS service not available on the current frequency the UE may reduce interval TreselectionS, TreselectionS, PCH and TreselectionS, FACH. Additionally the UE shall apply the following scaling rules to Treselections or Treselections,PCH or Treselections,FACH: For intra-frequency cells and high mobility state not detected: no scaling applied.
For intra-frequency cells and high mobility state is detected: multiply Treselections or Treselections,PCH or Treselections,FACH by the IE "Speed dependent ScalingFactor for_Treselection" if sent on system information.
For inter-frequency cells and high mobility state not detected:
3GPP
Release 7
27
3GPP TS 25.304 V7.8.0 (2009-09)
multiply Treselections or Treselections,PCH or Treselections,FACH by the IE "Inter-Frequency ScalingFactor for Treselection" if sent on system information.
For inter-frequency cells and high mobility state is detected: multiply Treselections or Treselections,PCH or Treselections,FACH by both the IEs "Speed dependent ScalingFactor for_Treselection" if sent on system information and "Inter-Frequency ScalingFactor for Treselection" if sent on system information.
For inter-RAT cells and high mobility state not detected: multiply Treselections or Treselections,PCH or Treselections,FACH by the IE "Inter-RAT ScalingFactor for Treselection" if sent on system information.
For inter-RAT cells and high mobility state is detected: multiply Treselections or Treselections,PCH or Treselections,FACH by both the IEs Speed dependent ScalingFactor for_Treselection if sent on system information and Inter-RAT ScalingFactor for Treselection" if sent on system information.
In case scaling is applied to Treselections or Treselections,PCH, the UE shall round up the result after all scalings to the nearest second. In case scaling is applied to Treselections,FACH, the UE shall round up the result after all scalings to the nearest 0.2 seconds. more than 1 second has elapsed since the UE camped on the current serving cell.
5.2.6.1.5
Cell reselection parameters in system information broadcasts
The selection of values for network controlled parameters can be optimised by means of different methods. Examples of methods are described in [6]. Cell reselection parameters are broadcast in system information and are read in the serving cell as follows: Qoffset1s,n This specifies the offset between the two cells. It is used for TDD and GSM cells and for FDD cells in case the quality measure for cell selection and re-selection is set to CPICH RSCP. Qoffset2s,n This specifies the offset between the two cells. It is used for FDD cells in case the quality measure for cell selection and re-selection is set to CPICH Ec/No. Qhyst1s This specifies the hysteresis value (Qhyst). It is used for TDD and GSM cells and for FDD cells in case the quality measure for cell selection and re-selection is set to CPICH RSCP. Qhyst1s,PCH This specifies the hysteresis value (Qhyst) to be used in RRC connected mode states CELL_PCH and URA_PCH. It is used for TDD and GSM cells and for FDD cells in case the quality measure for cell selection and re-selection is set to CPICH RSCP. If this parameter is not provided in SIB4, Qhyst1s shall be used. Qhyst1s,FACH This specifies the hysteresis value (Qhyst) to be used in RRC connected mode state CELL_FACH. It is used for TDD and GSM cells and for FDD cells in case the quality measure for cell selection and re-selection is set to CPICH RSCP. If this parameter is not provided in SIB4, Qhyst1s shall be used. Qhyst2s This specifies the hysteresis value (Qhyst). It is used for FDD cells if the quality measure for cell selection and reselection is set to CPICH Ec/No. Qhyst2s,PCH
3GPP
Release 7
28
3GPP TS 25.304 V7.8.0 (2009-09)
This specifies the hysteresis value (Qhyst) to be used in RRC connected mode states CELL_PCH and URA_PCH. It is used for FDD cells if the quality measure for cell selection and re-selection is set to CPICH Ec/No. If this parameter is not provided in SIB4, Qhyst2s shall be used. Qhyst2s,FACH This specifies the hysteresis value (Qhyst) to be used in RRC connected mode state CELL_FACH. It is used for FDD cells if the quality measure for cell selection and re-selection is set to CPICH Ec/No. If this parameter is not provided in SIB4, Qhyst2s shall be used. HCS_PRIOs, HCS_PRIOn This specifies the HCS priority level (0-7) for serving cell and neighbouring cells. HCS priority level 0 means lowest priority and HCS priority level 7 means highest priority. HCS_OFFmbms This specifies the offset to the normal HCS priority level that is used for cells belonging to the MBMS PL. Qhcss, Qhcsn This specifies the quality threshold levels for applying prioritised hierarchical cell re-selection. Qoffmbms This specifies the additional offset added to cells belonging to the MBMS PL. Qqualmin This specifies the minimum required quality level in the cell in dB. It is not applicable for TDD cells or GSM cells. Qrxlevmin This specifies the minimum required RX level in the cell in dBm. PENALTY_TIMEn This specifies the time duration for which the TEMPORARY_OFFSETn is applied for a neighbouring cell. TEMPORARY_OFFSET1n This specifies the offset applied to the H and R criteria for a neighbouring cell for the duration of PENALTY_TIMEn. It is used for TDD and GSM cells and for FDD cells in case the quality measure for cell selection and re-selection is set to CPICH RSCP. TEMPORARY_OFFSET2n This specifies the offset applied to the H and R criteria for a neighbouring cell for the duration of PENALTY_TIMEn. It is used for FDD cells in case the quality measure for cell selection and re-selection is set to CPICH Ec/No. TCRmax This specifies the duration for evaluating allowed amount of cell reselection(s). NCR This specifies the maximum number of cell reselections. TCRmaxHyst This specifies the additional time period before the UE can exit high-mobility. non-HCS_TCRmax This specifies the duration for evaluating allowed amount of cell reselection(s) in case of non-HCS usage. non-HCS_NCR
3GPP
Release 7
29
3GPP TS 25.304 V7.8.0 (2009-09)
This specifies the maximum number of cell reselections in case of non-HCS usage. non-HCS_TCRmaxHyst This specifies the additional time period before the UE can revert to low-mobility measurements in case of non-HCS usage. Treselections This specifies the cell reselection timer value. Treselections,PCH This specifies the cell reselection timer value the UE shall use in RRC connected mode states CELL_PCH and URA_PCH if provided in SIB4, otherwise Treselections shall be used. Treselections,FACH This specifies the cell reselection timer value the UE shall use in RRC connected mode state CELL_FACH if provided in SIB4, otherwise Treselections shall be used. SsearchHCS This threshold is used in the measurement rules for cell re-selection. When HCS is used, it specifies the limit for Srxlev in the serving cell below which the UE shall initiate measurements of all neighbouring cells of the serving cell. When HCS is not used, it specifies the limit for Srxlev in the serving cell below which the UE ranks inter-frequency neighbouring cells of the serving cell. SsearchRAT 1 - SsearchRAT k This specifies the RAT specific threshold in the serving cell used in the inter-RAT measurement rules. SHCS,RATm This threshold is used in the measurement rules for cell re-selection. When HCS is used, it specifies the RAT specific threshold in the serving cell used in the inter-RAT measurement rules. When HCS is not used, it specifies the limit for Srxlev in the serving cell below which the UE ranks inter-RAT neighbouring cells of the serving cell. Sintrasearch This specifies the threshold (in dB) for intra frequency measurements and for the HCS measurement rules. Sintersearch This specifies the threshold (in dB) for inter-frequency measurements and for the HCS measurement rules. Slimit,SearchRATm This threshold is used in the measurement rules for cell re-selection when HCS is used. It specifies the RAT specific threshold (in dB) in the serving UTRA cell above which the UE may choose to not perform any inter-RAT measurements in RAT "m". Speed dependent ScalingFactor for Treselection This specifies the scaling (multiplication) factor to be used by the UE in idle mode or RRC connected mode states for the parameters Treselections or Treselections,PCH or Treselections,FACH in case high-mobility state has been detected. Inter-frequency ScalingFactor for Treselection This specifies the scaling (multiplication) factor to be used by the UE for scaling the parameters Treselections or Treselections,PCH or Treselections,FACH for the inter-frequency case. Inter-RAT ScalingFactor for Treselection This specifies the scaling (multiplication) factor to be used by the UE for scaling the parameters Treselections or Treselections,PCH or Treselections,FACH for the inter-RAT case.
3GPP
Release 7
30
3GPP TS 25.304 V7.8.0 (2009-09)
5.2.6.2
GSM case
The cell reselection procedure in GSM, including reselection from GSM to UTRA, is specified in [1].
5.2.7
5.2.7.1
Cell Selection when leaving connected mode

UTRA case
When returning to idle mode from connected mode, the UE shall select a suitable cell to camp on. Candidate cells for this selection are the cell(s) used immediately before leaving connected mode. If no suitable cell is found, the UE shall use the Stored information cell selection procedure in order to find a suitable cell to camp on. When returning to idle mode after an emergency call on any PLMN, the UE shall select an acceptable cell to camp on. Candidate cells for this selection are the cell(s) used immediately before leaving connected mode. If no acceptable cell is found, the UE shall continue to search for an acceptable cell of any PLMN in state Any cell selection.
5.2.7.2
GSM case
Cell selection when leaving connected mode in GSM is specified in [1].
5.2.8
Any Cell Selection state
In this state, the UE shall attempt to find an acceptable cell of an any PLMN to camp on, trying all RATs that are supported by the UE and searching first for a high quality cell, as defined in subclause 5.1.2.2. The UE, which is not camped on any cell, shall stay in this state until an acceptable cell is found.
5.2.9
5.2.9.1
Camped on Any Cell State

UTRA case
In this state, the UE shall perform the following tasks: select and monitor the indicated PICH and PCH of the cell as specified in clause 8; monitor relevant System Information; This is specified in [4]; perform necessary measurements for the cell reselection evaluation procedure; Execute the cell reselection evaluation process on the following occasions/triggers: 1) UE internal triggers, so as to meet performance as specified in [10] and [11]; 2) When information on the BCCH used for the cell reselection evaluation procedure has been modified; regularly attempt to find a suitable cell trying all RATs that are supported by the UE. If a suitable cell is found, this causes an exit to number 2 in Figure 2.
In this state the UE is not permitted to receive any MBMS services.
5.2.9.2
GSM case
The camped on any cell state in GSM is specified in [1].
3GPP
Release 7
31
3GPP TS 25.304 V7.8.0 (2009-09)
5.3
5.3.1
Cell Reservations and Access Restrictions (cells not operating in MBSFN mode)
UTRA cells
There are two mechanisms which allow an operator to impose cell reservations or access restrictions. The first mechanism uses indication of cell status and special reservations for control of cell selection and re-selection procedures. The second mechanism, referred to as Access Control, shall allow to prevent selected classes of users from sending initial access messages for load control reasons. At subscription, one or more Access Classes are allocated to the subscriber and stored in the USIM [9], which are employed for this purpose.
5.3.1.1
Cell status and cell reservations
Cell status and cell reservations are indicated with the Cell Access Restriction Information Element in the System Information Message [4] by means of three Information Elements: Cell barred (IE type: "barred" or "not barred"), Cell Reserved for operator use (IE type: "reserved" or "not reserved"), Cell reserved for future extension (IE type: "reserved" or "not reserved").
When cell status is indicated as "not barred", "not reserved" for operator use and "not reserved" for future extension (Cell Reservation Extension), All UEs shall treat this cell as candidate during the cell selection and cell re-selection procedures in Idle mode and in Connected mode.
When cell status is indicated as "not barred", "not reserved" for operator use and "reserved" for future extension (Cell Reservation Extension), UEs shall behave as if cell status "barred" is indicated using the value "not allowed" in the IE "Intra-frequency cell re-selection indicator" and the maximum value for Tbarred, see [4] (see also below).
When cell status is indicated as "not barred" and "reserved" for operator use, UEs assigned to Access Class 11 or 15 shall treat this cell as candidate during the cell selection and cell reselection procedures in Idle mode and in Connected mode if the cell belongs to the home PLMN or to any EHPLMN if present. UEs assigned to an Access Class in the range 0 to 9 and 12 to 14 shall behave as if cell status "barred" is indicated using the value "not allowed" in the IE "Intra-frequency cell re-selection indicator" and the maximum value for Tbarred, see [4] (see also below).
When cell status "barred" is indicated, The UE is not permitted to select/re-select this cell, not even for emergency calls. The UE shall ignore the "Cell Reserved for future extension (Cell Reservation Extension) use" IE. The UE is not permitted to receive any MBMS services. The UE shall select another cell according to the following rule: If the "Intra-frequency cell re-selection indicator" IE in Cell Access Restriction IE is set to value "allowed", the UE may select another cell on the same frequency if selection/re-selection criteria are fulfilled. If the UE is camping on another cell, the UE shall exclude the barred cell from the neighbouring cell list until the expiry of a time interval Tbarred. The time interval Tbarred is sent via system information in a barred cell together with Cell status information in the Cell Access Restriction IE. If the UE does not select another cell, and the barred cell remains to be the "best" one, the UE shall after expiry of the time interval Tbarred again check whether the status of the barred cell has changed.
3GPP
Release 7
32
3GPP TS 25.304 V7.8.0 (2009-09)
If the "Intra-frequency cell re-selection indicator" IE is set to "not allowed" the UE shall not re-select a cell on the same frequency as the barred cell. During an ongoing emergency call, the Intra-frequency cell reselection indicator IE" shall be ignored, i.e. even if it is set to "not allowed" the UE may select another intrafrequency cell. If the barred cell remains to be the "best" one, the UE shall after expiry of the time interval Tbarred again check whether the status of the barred cell has changed.
The reselection to another cell may also include a change of RAT.
5.3.1.2
Access Control
Information on cell access restrictions associated with the Access Classes is broadcast as system information, [4]. The UE shall ignore Access Class related cell access restrictions when selecting a cell to camp on, i.e. it shall not reject a cell for camping on because access on that cell is not allowed for any of the Access Classes of the UE. A change of the indicated access restriction shall not trigger cell re-selection by the UE. Access Class related cell access restrictions shall be checked by the UE before sending an RRC CONNECTION REQUEST message when entering Connected Mode from UTRAN Idle mode. Access Class related cell access restrictions, if it is sent as a part of Domain Specific Access Restriction parameters, shall also be checked by the UE before sending INITIAL DIRECT TRANSFER message. Otherwise, cell access restrictions associated with the Access Classes shall not apply for a UE which already is in Connected Mode.
5.3.1.3
Emergency Call
A restriction on emergency calls, if needed, shall be indicated in the "Access class barred list" IE [4]. If access class 10 is indicated as barred in a cell, UEs with access class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with access classes 11 to 15, emergency calls are not allowed if both access class 10 and the relevant access class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Full details of operation under "Access class barred list" are described in [9].
5.3.2
GSM cells
The cell access restrictions applicable to GSM are specified in [1].
5.3a
Cell Reservations and Access Restrictions (MBSFN cells only for FDD and 3.84/7.68 Mcps TDD)
For an MBSFN cluster (see [4]) when cell status is indicated "not reserved" for operator use and "not reserved" for future extension (Cell Reservation Extension), and Cell Barred is set to "barred" or "not barred", All UEs shall treat this MBSFN cluster as candidate during the MBSFN cluster selection and MBSFN cluster reselection procedures.
For an MBSFN cluster (see [4]) when cell status is indicated as "not reserved" for operator use and "reserved" for future extension (Cell Reservation Extension), UEs shall not consider this MBSFN cluster as candidate during the MBSFN cluster selection and MBSFN cluster re-selection procedures. The UE may choose to not recheck the status of this MBSFN cluster during the time corresponding to the maximum value for Tbarred (see [4]).
For an MBSFN cluster (see [4]) when cell status is indicated as "reserved" for operator use, UEs assigned to Access Class 11 or 15 shall treat this MBSFN cluster as candidate during the MBSFN cluster selection and MBSFN cluster re-selection procedures. UEs assigned to an Access Class in the range 0 to 9 and 12 to 14 shall not consider this MBSFN cluster as candidate during the MBSFN cluster selection and MBSFN cluster re-selection procedures The UE may choose
3GPP
Release 7
33
3GPP TS 25.304 V7.8.0 (2009-09)
to not recheck the status of this MBSFN cluster during the time corresponding to the maximum value for Tbarred (see [4]). Note: The UE should in all cases assume intra-frequency cell re-selection has the value allowed.
5.4
5.4.1
Cell Selection and Reselection Processes in RRC Connected Mode

Void
5.4.2
Void
5.4.3
Cell Reselection Process in RRC connected mode
The cell reselection process in Connected Mode is the same as cell reselection evaluation process used for idle mode, described in subclause 5.2.6.
5.4.4
Cell Selection Process in RRC connected mode
The cell selection process in Connected Mode is for out of service conditions [4] is the same as the cell selection process used for idle mode, described in subclause 5.2.3. Selection of a suitable cell during a state transition or a change of frequency in Connected Mode is the same as the selection of a suitable UTRA cell used for idle mode, described in subclause 5.2.3.1. If the UE is ordered to select a suitable UTRA cell on a given frequency, it shall attempt to select a suitable cell on that frequency before considering cells on other frequencies.
5.5
Location Registration
In the UE, the AS shall report registration area information to the NAS. If the UE reads more than one PLMN identity in the current cell, the UE shall report the found PLMN identities that make the cell suitable in the registration area information to NAS. The non-access part of the location registration process is specified in [5]. Actions for the UE AS upon reception of Location Registration reject are specified in [9] and [16].
6
6.1
Broadcast information receiving

Reception of System Information
Requirements are specified in [4].
6.2
Cell Broadcast in Idle Mode, CELL_PCH and URA_PCH
A UE supporting Cell Broadcast Service (CBS) shall be capable to receive BMC messages in the Idle mode, in URA_PCH and CELL_PCH. When several PCHs exist in the cell, the FACH which carries the CTCH may be mapped to a different SCCPCH than the PCH selected by the UE for paging in Idle mode (as specified in Sec. 8.1). In this case, UEs with basic service capabilities shall be capable to change from the SCCPCH that carries the PCH selected for
3GPP
Release 7
34
3GPP TS 25.304 V7.8.0 (2009-09)
paging to another SCCPCH which carries Cell Broadcast messages (i.e. the CTCH mapped to an FACH) and receive BMC messages during time intervals which do not conflict with the UE specific paging occasions. NOTE: In case certain BMC messages conflict with the UE specific paging occasions the reception of CBS cannot be guaranteed and depends on UE capabilities.
6.3
MBMS Services
If the UE has activated MBMS services and MBMS is available in the cell (i.e., the MCCH information is provided on the BCCH) and the UE is permitted to receive MBMS in the cell, the UE shall: receive the MCCH as specified in clause 8.4 and in [4]; participate in MBMS counting as specified in [4]; receive each FACH on which the MTCH carrying an MBMS activated service that does not require the establishment of an RRC connection is mapped.
The UE may: monitor the MICH as specified in clause 8a and in [4]; receive the MSCH.
6.3.1
6.3.1.1
MBSFN cluster selection and reselection

MBSFN cluster selection
MBSFN cluster selection/reselection process for MBSFN clusters operating on the same frequency may be based on reception quality of the CPICH for FDD or P-CCPCH for TDD. Details of the process are not specified. The UE shall search for MBSFN clusters if the frequencies on which MBSFN clusters are available are not indicated in the cell that the UE is camping on for normal service if the mobile is configured to receive services via MBSFN mode. Details of the process are not specified. For 1.28 Mcps TDD, the UE that needs receive MBMS services delivered in an MBSFN cluster may at the first step select a non MBSFN cell (i.e. a unicast cell), that the MBSFN cluster is associated with. The UE can get synchronized to the MBSFN cluster with the help of the information indicated in system information broadcast by the associated unicast cell,and receive the system information and MCCH messages in the MBSFN Special Timeslot. The details of the association between MBSFN clusters and non MBSFN cells operating in a unicast carrier are not specified. In case there are more than one MBSFN clusters indicated in system information broadcast by a unicast cell, the process of which MBSFN cluster should be selected for searching is not specified.
6.3.1.2
Camped on MBSFN cluster
When camped on a MBSFN cluster, the UE shall perform the following tasks: receive the MCCH as specified in clause 8.4 and in [4]; monitor the available MBMS services on theMBSFN cluster that the UE is camping on
The UE may: monitor the MICH as specified in clause 8a and in [4]; receive the MSCH.
3GPP
Release 7
35
3GPP TS 25.304 V7.8.0 (2009-09)
6.3.1.3
MBSFN inter frequency neighbour information
Upon detection of one MBSFN cluster all other frequencies on which MBMS service is provided in MBSFN mode for one of the PLMN assigned to the MBSFN cluster are indicate as specified in [4]. The UE chooses the frequency for the MBSFN cluster to be received based on the information on the services that are provided on the MBSFN clusters of those frequencies. In the case that the UE does not receive a service from the current MBSFN cluster and the UE is configured to receive an MBMS service in MBSFN mode it should attempt to receive information on ongoing services as specified in [4].
Void
8
8.1
Paging and SCCPCH selection and in FDD the HRNTI selection

Paging Channel selection
System information block type 5 (SIB 5) and System information block type 5bis (SIB 5bis)define common channels to be employed in Idle mode [4]. In a cell, a single or several PCHs may be established. Each Secondary Common Control Physical Channel (SCCPCH) indicated to the UE in system information may carry up to one PCH. Thus, for each defined PCH there is one uniquely associated PICH also indicated. In case that more than a single PCH and associated PICH are defined in SIB 5 or SIB 5bis, the UE shall perform a selection according to the following rule: The UE shall select a SCCPCH from the ones listed in SIB 5 or SIB 5bis based on IMSI as follows: "Index of selected SCCPCH" = IMSI mod K, where K is equal to the number of listed SCCPCHs which carry a PCH (i.e. SCCPCHs carrying FACH only shall not be counted). These SCCPCHs shall be indexed in the order of their occurrence in SIB 5 or SIB 5bis from 0 to K-1. For GSM-MAP, i.e. "IMSI (GSM-MAP)" is given as sequence of digits of type Integer(0..9), IMSI shall in the formula above be interpreted as a decimal integer number, where the first digit given in the sequence represents the highest order digit. For DS-41, i.e. "IMSI (DS-41)" is given as octet string, IMSI shall in the formulae above correspond to the decoded decimal representation of the IMSI-S part included in the octet string (see TIA/EIA/IS-2000-5). For example: IMSI (GSM-MAP) = 12 (digit1=1, digit2=2) In the calculations, this shall be interpreted as the decimal integer "12", not "1x16+2 = 18". "Index of selected SCCPCH" identifies the selected SCCPCH with the PCH and the uniquely associated PICH to be used by the UE. If the UE has no IMSI, for instance when making an emergency call without USIM, the UE shall use as default number IMSI = 0.
8.2
SCCPCH selection when entering Connected mode
If HS-DSCH operation in CELL_FACH state (FDD only) is not configured to the cell, when entering Connected mode from Idle mode by sending an RRC CONNECTION REQUEST message, the UE shall select the S-CCPCH which carries an FACH to be used for reception of the RRC CONNECTION SETUP message according to the following rule:
3GPP
Release 7
36
3GPP TS 25.304 V7.8.0 (2009-09)
the UE shall select an SCCPCH from the SCCPCHs listed in System Information Block type 5 (SIB 5) or System Information Block type 5bis (SIB 5bis) based on "Initial UE Identity" as follows: "Index of selected SCCPCH" = "Initial UE Identity" mod K, where K is equal to the number of listed SCCPCHs which carry a FACH (i.e. SCCPCHs carrying PCH only shall not be counted). These SCCPCHs shall be indexed from 0 to K-1 in the order of their occurrence in SIB 5 or SIB 5bis, and "Index of selected SCCPCH" identifies the selected SCCPCH. "Initial UE Identity" refers to the Information Element included by the UE into the RRC CONNECTION REQUEST message. In the above formula, the parameter "Initial UE Identity" shall be interpreted as follows, depending on the choice of UE-Id type of the respective IE: For UE-Id type "IMSI (GSM-MAP)", i.e. the IE is given as sequence of digits of type Integer(0..9), "Initial UE Identity" shall be interpreted as an integer number, where the first digit given in the sequence represents the highest order digit. For UE-Id types "TMSI and LAI (GSM-MAP)" or "P-TMSI and RAI (GSM-MAP)", only the TMSI or PTMSI parts given as Bitstring(32) shall be used, and "Initial UE Identity" shall be interpreted as a binary representation of an integer number, where the first bit in the Bitstring represents the highest order bit. For UE-Id type "IMEI", i.e. the IE is given as sequence of hexadecimal digits of type Integer(0..15), "Initial UE Identity" shall be interpreted as a hexadecimal representation of an integer number, where the first digit given in the sequence represents the highest order digit. For UE-Id type "IMSI (DS-41)", i.e. the IE is given as octet string, "Initial UE Identity" shall correspond to the decoded decimal representation of the IMSI-S part included in the octet string (see TIA/EIA/IS-2000-5). For UE-Id types "ESN (DS-41)" or "TMSI (DS-41)", i.e. the IE is given as Bitstring(32), "Initial UE Identity" shall be interpreted as a binary representation of an integer number, where the first bit in the Bitstring represents the highest order bit. For UE-Id type "IMSI and ESN (DS-41)" only the ESN part shall be used as "Initial UE Identity", as defined above.
8.2b
H-RNTI selection when entering Connected mode (FDD only)
If HS-DSCH operation in CELL_FACH state is configured to the cell in System Information Block type 5 (SIB 5) or System Information Block type 5bis, when entering Connected mode from Idle mode by sending an RRC CONNECTION REQUEST message, the UE shall start listening to the HS-SCCH indicated in System Information Block type 5 (SIB 5) or in System Information Block type 5bis (SIB 5bis). The detection of HS-SCCH is based on Common H-RNTI listed in System Information Block type 5 (SIB 5) or System Information Block type 5bis (SIB 5bis). The UE shall select the Common H-RNTI to be used for reception of the RRC CONNECTION SETUP message according to the following rule: the UE shall select a Common H-RNTI from the Common H-RNTIs listed in System Information Block type 5 (SIB 5) or System Information Block type 5bis (SIB 5bis) based on "Initial UE Identity" as follows: "Index of selected Common H-RNTI" = "Initial UE Identity" mod K, where K is equal to the number of listed Common H-RNTI. These Common H-RNTIs shall be indexed from 0 to K-1 in the order of their occurrence in SIB 5 or SIB 5bis, and "Index of selected Common H-RNTI" identifies the selected Common H-RNTI. "Initial UE Identity" refers to the Information Element included by the UE into the RRC CONNECTION REQUEST message. In the above formula, the parameter "Initial UE Identity" shall be interpreted as follows, depending on the choice of UE-Id type of the respective IE: For UE-Id type "IMSI (GSM-MAP)", i.e. the IE is given as sequence of digits of type Integer(0..9), "Initial UE Identity" shall be interpreted as an integer number, where the first digit given in the sequence represents the highest order digit.
3GPP
Release 7
37
3GPP TS 25.304 V7.8.0 (2009-09)
For UE-Id types "TMSI and LAI (GSM-MAP)" or "P-TMSI and RAI (GSM-MAP)", only the TMSI or PTMSI parts given as Bitstring(32) shall be used, and "Initial UE Identity" shall be interpreted as a binary representation of an integer number, where the first bit in the Bitstring represents the highest order bit. For UE-Id type "IMEI", i.e. the IE is given as sequence of hexadecimal digits of type Integer(0..15), "Initial UE Identity" shall be interpreted as a hexadecimal representation of an integer number, where the first digit given in the sequence represents the highest order digit. For UE-Id type "IMSI (DS-41)", i.e. the IE is given as octet string, "Initial UE Identity" shall correspond to the decoded decimal representation of the IMSI-S part included in the octet string (see TIA/EIA/IS-2000-5). For UE-Id types "ESN (DS-41)" or "TMSI (DS-41)", i.e. the IE is given as Bitstring(32), "Initial UE Identity" shall be interpreted as a binary representation of an integer number, where the first bit in the Bitstring represents the highest order bit. For UE-Id type "IMSI and ESN (DS-41)" only the ESN part shall be used as "Initial UE Identity", as defined above. After detecting the HS-SCCH with Common H-RNTI, the UE start reception of the corresponding HS-PDSCH(s) TTI.
8.3
Discontinuous Reception for Paging
The UE may use Discontinuous Reception (DRX) in idle mode in order to reduce power consumption. When DRX is used the UE needs only to monitor one Page Indicator, PI, (see definition in [7] and [8]) in one Paging Occasion per DRX cycle. The DRX cycle length shall be MAX(2k, PBP) frames, where k is an integer and PBP is the Paging Block Periodicity. PBP is only applicable for TDD and is equal to the PICH repetition period that is broadcast in system information. For FDD, PBP=1. The UE may be attached to different CN domains with different CN domain specific DRX cycle lengths. The UE shall store each CN domain specific DRX cycle length for each CN domain the UE is attached to and use the shortest of those DRX cycle lengths. The CS CN specific DRX cycle length coefficient shall be updated locally in the UE using information given in system information. On the other hand, the PS CN specific DRX cycle length coefficient shall be updated after the negotiation between the UE and PS CN by NAS procedure. If no specific value "k" is negotiated in NAS procedure, the UE and PS CN shall use the DRX cycle length given for PS CN domain in system information. The DRX cycle lengths to use for UTRAN connected mode is the shortest of the following: UTRAN DRX cycle length; any of the stored CN domain specific DRX cycle length for the CN domains the UE is only attached to with no signalling connection established.
For TDD, and for FDD in IDLE mode as well as in RRC Connected mode, if HS-DSCH operation in CELL_PCH and URA_PCH state is not configured to the cell, the UE shall use the IMSI, the number of available SCCPCH which carry a PCH (K) as derived according to subclause 8.1,the Cell System Frame Number (SFN), Np (for FDD, Np is the number of page indicators within a frame; for TDD, Np is the number of page indicators within a paging block), Frame offset (For FDD, Frame offset = 0; for TDD, PICH frame offset values are given in system information), PBP and the DRX cycle length to determine the Paging Occasions. For FDD, if HS-DSCH operation in CELL_PCH and URA_PCH state is configured to the cell, the UE in RRC Conneced mode shall use the IMSI, the number of indexed PICH for HSDPA supported paging (K) as derived from System Information Block Type 5 or System Information Block Type 5bis, the Cell System Frame Number (SFN), Np (Np is the number of page indicators within a frame), Frame offset (Frame offset = 0), PBP and the DRX cycle length to determine the Paging Occasions. In FDD the UE shall monitor its paging indicator in the PICH frame with SFN given by the Paging Occasion In TDD the UE shall monitor its paging indicator in the paging block given by the Paging Occasion. The Paging Occasion gives the SFN of the first frame of the paging block. The value of the Paging Occasion is determined as follows:
3GPP
Release 7
38
3GPP TS 25.304 V7.8.0 (2009-09)
Paging Occasion= {(IMSI div K) mod (DRX cycle length div PBP)} * PBP + n * DRX cycle length + Frame Offset Where n = 0,1,2 as long as SFN is below its maximum value. The actual Page Indicator within a Paging Occasion that the UE shall read is similarly determined based on IMSI. The Page Indicator to use is calculated by using the following formula: PI = DRX Index mod Np where DRX Index = IMSI div 8192 In FDD mode, Np = (18,36,72,144) is the number of Page Indicators per frame, and is given in IE "Number of PI per frame", part of system information in FDD mode. In TDD mode, Np is the number of Page Indicators per paging block and is calculated by the Paging Indicator Length LPI, the Burst Type (long or short midamble for 3.84/7.68 Mcps TDD) and the PICH repetition length, which are given in system information. If the UE has no IMSI, for instance when making an emergency call without USIM, the UE shall use as default numbers, IMSI = 0 and DRX cycle length = 256 (2.56 s), in the formulas above. For FDD, see [7] for details about the timing between a PICH frame and when the paging message is transmitted on the PCH in the associated S-CCPCH frame. In TDD mode, the Paging Message Receiving Occasion is calculated using the following formula: Paging Message Receiving Occasion =Paging Occasion + NPICH + NGAP + {(DRX Index mod Np) mod NPCH } *2 The value NPICH is the number of frames for PICH transmission and is equal to the PICH repetition length given in system information. The value NGAP is the number of frames between the last frame carrying PICH for this Paging Occasion and the first frame carrying paging messages for this Paging Occasion. The value NPCH is the number of Paging Groups. NPCH and NGAP are given in system information. For GSM-MAP, i.e. "IMSI (GSM-MAP)" is given as sequence of digits of type Integer(0..9), IMSI shall in the formulae above be interpreted as a decimal integer number, where the first digit given in the sequence represents the highest order digit. For DS-41, i.e. "IMSI (DS-41)" is given as octet string, IMSI shall in the formulae above correspond to the decoded decimal representation of the IMSI-S part included in the octet string (see TIA/EIA/IS-2000-5). For example: IMSI (GSM-MAP) = 12 (digit1=1, digit2=2) In the calculations, this shall be interpreted as the decimal integer "12", not "1x16+2 = 18".
8.4
Discontinuous Reception for MBMS
The UE may use discontinuous reception (DRX) on MBMS channels (MCCH, MSCH, MTCH) to reduce power consumption while subscribed to MBMS services.
8.4.1
Discontinuous Reception for MCCH
The UE may operate DRX on the MCCH either by monitoring the MICH to determine when it needs to receive the MCCH or by using the MODIFIED SERVICES INFORMATION message on the MCCH to determine that it does not need to acquire the remainder of the MCCH information. The timing of the MCCH information transmission and the need to receive the MCCH are described in detail in [4].
8.4.1.1
Discontinuous Reception via MICH
When the UE operates DRX on the MCCH through monitoring the MICH, the UE needs to monitor one Notification Indicator (NI), as defined in [7], [8], for each MBMS service it is subscribed to. For each service, a corresponding NI will be set continuously through the entire length of the modification period preceding a change in the associated
3GPP
Release 7
39
3GPP TS 25.304 V7.8.0 (2009-09)
MCCH information. The modification period should be long enough that a UE that only receives the MICH during its paging occasions can still reliably detect a notification. For each service, the 16 bit Notification Indicator to use is calculated as a function of the TMGI:
NI
TMGI
TMGI / G mod G , where G = 216.
A UE with one or more activated MBMS services may monitor the MICH. The exact timing with which the UE reads the MICH within a given modification period is left to the UE implementation, with the proviso that the UE needs to be able to detect notifications reliably for its activated MBMS service(s). The TMGI is structured as follows [16]: 8 6 5 4 3 2 1 Temporary Mobile Group Identity IEI Length of Temporary Mobile Group Identity contents MBMS Service ID MCC digit 2 MNC digit 3 MNC digit 2 NOTE: MCC digit 1 MCC digit 3 MNC digit 1 7 Octet 1 Octet 2 Octet 3 Octet 4 Octet 5 Octet 6 Octet 7 Octet 8
The MBMS Service identity, which is signalled in [4] (see subclause 10.3.9a.8), concerns a signalling optimisation of the TMGI.
For the calculation of the NI, the TMGI shall be interpreted as a binary representation of an integer number, represented by the bitstring formed by the exclusive OR operation of the MBMS Service ID (octets 3 to 5 of the TMGI) and the PLMN identity (octets 6 to 8 of the TMGI) with the first/ leftmost/ most significant bit corresponding with b8 of the first octet.
8.4.1.2
Discontinuous Reception via MODIFIED SERVICES INFORMATION
If the UE receives the MODIFIED SERVICES INFORMATION message on the MCCH and determines from its contents that no service whose information the UE needs to acquire has been modified, the UE may refrain from receiving the MCCH for the remainder of the modification period.
8.4.2
Discontinuous Reception for MTCH
If the UE operates DRX on the MTCH, the UE shall receive the MSCH as described in [4] to obtain scheduling information for the MTCH. The reception intervals for MBMS services are given by the IE Service transmissions list in the MBMS SCHEDULING INFORMATION message on the MSCH.
8a
MBMS Notification
The structure of the MICH is described in [7] and [14]. The RRC-layer behaviour of a UE receiving an MBMS notification indicator is specified in [4].
Void
3GPP
Release 7
40
3GPP TS 25.304 V7.8.0 (2009-09)
10
Void
Annex A (informative): Change history

Change history
Date 10/1999 12/1999 TSG # RP-05 RP-06 RP-06 RP-06 RP-06 RP-06 RP-06 RP-06 RP-06 RP-07 RP-07 RP-07 RP-07 RP-07 RP-08 RP-08 RP-08 RP-08 RP-08 RP-08 RP-08 RP-09 RP-09 RP-09 RP-09 RP-09 RP-10 RP-10 RP-10 RP-10 RP-10 RP-10 RP-10 RP-11 RP-11 RP-11 RP-11 RP-11 RP-11 RP-11 RP-11 RP-11 RP-11 RP-11 RP-12 RP-12 RP-12 RP-13 RP-13 RP-13 RP-13 RP-13 RP-13 RP-14 RP-14 RP-15 RP-15 TSG Doc. RP-99464 RP-99632 RP-99633 RP-99633 RP-99633 RP-99632 RP-99633 RP-99633 RP-99631 RP-000037 RP-000037 RP-000037 RP-000037 RP-000037 RP-000217 RP-000217 RP-000217 RP-000217 RP-000217 RP-000217 RP-000217 RP-000355 RP-000355 RP-000355 RP-000355 RP-000355 RP-000565 RP-000565 RP-000565 RP-000565 RP-000565 RP-000565 RP-000565 RP-010022 RP-010022 RP-010022 RP-010022 RP-010022 RP-010022 RP-010022 RP-010200 RP-010022 RP-010022 RP-010037 RP-010305 RP-010435 RP-010305 RP-010539 RP-010539 RP-010539 RP-010539 RP-010539 RP-010539 RP-010756 RP-010756 RP-020063 RP-020063 CR 001 002 003 004 006 008 009 011 007 014 018 019 021 025 026 027 028 029 030 031 035 037 039 042 044 046 049 050 051 052 053 054 055 056 058 059 061 062 063 064 065 066 057 072 074 078 080 082 084 086 088 090 092 094 096 098 Rev 2 3 2 2 3 Subject/Comment Approved at TSG-RAN #5 and placed under Change Control Modification and editorial changes Specification of Cell reselection procedures in Integration of Cell Broadcast Service (CBS) Measurement used as a quality estimate for cell Discontinuous reception Barred Cells and Access Control Introduction of network control of UE measurement Editorial issues Cell Selection for DS-41 mode Modified description of cell search procedure UE individual DRX cycles in CELL_PCH and URA_PCH states Cell re-selection criteria including HCS Modified description of DRX Triggering of inter-system measurements for cell re-selection when HCS is used Cell re-selection Access Control Downlink signalling failure Cell-reselection parameter signalling Cell Selection and Reselection CN DRX cycle coefficient Paging channel selection Editorial corrections HCS measurement rules Usage of Ec/N0 measurement quantity for cell ranking Correction and restructuring Support for PLMN selection Correction of algorithm for paging channel selection Alignment of use of TEMP_OFFSET parameters with TS 25.331 Clarifications and Editorial Corrections Clarifications to cell selection and reselection procedures Removal of immediate cell evaluation One step cell selection Usage of HCS Parameters in Cell Reselection Clarification of usage of "Initial UE-Id" for SCCPCH selection Clarification of paging occasion Correction in Any Cell Selection State Correction to the definition of a suitable cell Correction to discontinuous reception in TDD Correction of PI calculation for Paging DRX Equivalent PLMN codes High quality cell in PLMN selection Clean-up Support of 1.28Mcps TDD Corrections to 25.304 Emergency calls in barred cells Clarification to usage of measurement thresholds Clarification to usage of measurement thresholds for HCS Definition of strongest cell in cell search procedures Miscellaneous corrections Correction to cells reserved for operator use Service type also valid in connected mode Cell Access Restrictions for emergency calls Clarification on DRX cycle length in connected mode Correction to search for available PLMNs Correction to TDD paging message receiving occasion Clarification of IMSI at Paging channel selection and DRX calculation Old 3.0.0 3.0.0 3.0.0 3.0.0 3.0.0 3.0.0 3.0.0 3.0.0 3.1.0 3.1.0 3.1.0 3.1.0 3.1.0 3.2.0 3.2.0 3.2.0 3.2.0 3.2.0 3.2.0 3.2.0 3.3.0 3.3.0 3.3.0 3.3.0 3.3.0 3.4.0 3.4.0 3.4.0 3.4.0 3.4.0 3.4.0 3.4.0 3.5.0 3.5.0 3.5.0 3.5.0 3.5.0 3.5.0 3.5.0 3.5.0 3.5.0 3.5.0 3.6.0 4.0.0 4.0.0 4.0.0 4.1.0 4.1.0 4.1.0 4.1.0 4.1.0 4.1.0 4.2.0 4.2.0 4.3.0 4.3.0 New 3.0.0 3.1.0 3.1.0 3.1.0 3.1.0 3.1.0 3.1.0 3.1.0 3.1.0 3.2.0 3.2.0 3.2.0 3.2.0 3.2.0 3.3.0 3.3.0 3.3.0 3.3.0 3.3.0 3.3.0 3.3.0 3.4.0 3.4.0 3.4.0 3.4.0 3.4.0 3.5.0 3.5.0 3.5.0 3.5.0 3.5.0 3.5.0 3.5.0 3.6.0 3.6.0 3.6.0 3.6.0 3.6.0 3.6.0 3.6.0 3.6.0 3.6.0 3.6.0 4.0.0 4.1.0 4.1.0 4.1.0 4.2.0 4.2.0 4.2.0 4.2.0 4.2.0 4.2.0 4.3.0 4.3.0 4.4.0 4.4.0
03/2000
2 1 1
06/2000
5 4
09/2000
1 2 1 2 1 1 2 1
12/2000
03/2001
1 3
1 1
06/2001
09/2001
1 1
12/2001 03/2002
3GPP
Release 7
RP-15 RP-16 RP-18 RP-20 RP-22 RP-23 RP-24 RP-24 RP-24 RP-25 RP-26 RP-26 RP-26 RP-26 RP-26 RP-27 RP-27 RP-27 RP-27 RP-27 RP-27 RP-27 RP-27 RP-28 RP-28 RP-28 RP-29 RP-29 RP-29 RP-29 RP-29 RP-31 RP-31 RP-31 RP-31 RP-34 RP-36 RP-36 RP-36 RP-36 RP-37 RP-38 RP-39 RP-40 RP-41 RP-45 RP-020324 RP-020716 RP-030289 RP-040094 RP-040208 RP-040208 RP-040208 RP-040332 RP-040526 RP-040506 RP-040494 RP-040488 RP-040488 RP-050081 RP-050073 RP-050073 RP-050073 RP-050112 RP-050077 RP-050128 RP-050073 RP-050314 RP-050314 RP-050314 RP-050460 RP-050479 RP-050479 RP-050468 101 104 107 111 113 116 114 119 121 123 124 126 127 125 129 131 132 133 134 137 139 0140 0141 0142 0145 0146 0147 0148
41
3GPP TS 25.304 V7.8.0 (2009-09)

4.4.0 5.0.0 5.1.0 5.2.0 5.3.0 6.0.0 6.1.0 6.1.0 6.1.0 6.2.0 6.3.0 6.3.0 6.3.0 6.3.0 6.3.0 6.4.0 6.4.0 6.4.0 6.4.0 6.4.0 6.4.0 6.4.0 6.4.0 6.5.0 6.5.0 6.5.0 6.6.0 6.6.0 6.6.0 6.6.0 6.7.0 6.8.0 6.8.0 6.8.0 6.9.0 7.0.0 7.1.0 7.1.0 7.1.0 7.1.0 7.2.0 7.3.0 7.4.0 7.5.0 7.6.0 7.7.0 5.0.0 5.1.0 5.2.0 5.3.0 6.0.0 6.1.0 6.2.0 6.2.0 6.2.0 6.3.0 6.4.0 6.4.0 6.4.0 6.4.0 6.4.0 6.5.0 6.5.0 6.5.0 6.5.0 6.5.0 6.5.0 6.5.0 6.5.0 6.6.0 6.6.0 6.6.0 6.7.0 6.7.0 6.7.0 6.7.0 6.8.0 6.9.0 6.9.0 6.9.0 7.0.0 7.1.0 7.2.0 7.2.0 7.2.0 7.2.0 7.3.0 7.4.0 7.5.0 7.6.0 7.7.0 7.8.0
06/2002 12/2002 06/2003 12/2003 03/2004 06/2004
1 1 3 2
09/2004 12/2004
03/2005
1 1 1 2
1 1
06/2005
09/2005
12/2005 03/2006
RP-050788 0150 RP-060188 0151 RP-060090 RP-060090 RP-060098 RP-060712 RP-070403 RP-070407 RP-070407 RP-070400 RP-070671 RP-070902 RP-080177 RP-080403 RP-080680 RP-090901 0152 0153 0154 0155 0156 0157 0158 0159 0160 0161 0163 0165 0167 0214
2 1
12/2006 06/2007
09/2007 12/2007 03/2008 05/2008 09/2008 09/2009
1 1 2 -
Upgrade to Release 5 - no technical change Limitations of CBS reception Highest HCS priority Correction to cell selection process to include RRC connected mode Upgrade to Release 6 - no technical changes H criteria & High mobility reselection Correction to UE selection of reserved cells Modification of the Sintersearch and SsearchRAT,m behaviour Selection of suitable cell HCS measurement rules & high-mobility Cell selection and reselection parameters Use of access class restrictions at Inter-RAT cell change Network Sharing and multiple PLMN identities TS 25.304 Introduction of MBMS Addition of MBMS Frequency Layer Convergence to 25.304 Correction to "selected PLMN" in access stratum Reselection procedure (1235) RSCP Thresholds HCS High-mobility measurement rules H criterion in HCS high-mobility MBMS Scope Correction to cell selection and reselection parameters to enable enhanced cell reselection Intra frequency measurement rules for HCS Addition of idle mode cell selection due to FLD MBMS Frequency Layer Convergence Removal of sentences in brackets in 25.304 Correction to condition for starting penalty timer in HCS reselection Selecting the correct priority layer in HCS high mobility Correction to inter-frequency cell reselection when HCS is not used Correction to cell reselection when HCS is not used and MBMS PL is indicated Structure and use of TMGI for MBMS notification Effect of partial roaming restrictions on cell reselection and proposed performance enhancement Corrected UE behaviour at LR reject Clarification regarding Access Class and Initial Direct Transfer 7.68 Mpcs TDD Option (Release 7) Introduction high mobility detection on RRC state change Introduction of HS-DSCH operation in CELL_FACH state S-CCPCH and PCH channel selection for Band IV or Band IX or Band X PLMN selection ping-pong control MBMS FDD and TDD Physical Layer Improvements H-RNTI selection More improvement on Dedicated Carrier for 1.28Mcps TDD MBMS Clarification on Treselection for MBMS Correction to HCS MBSFN Corrections Applicability of EHPLMN to 'reserved for operator use' barring
3GPP

3GPP TS 25.304

Uploaded by

Copyright:

Available Formats

3GPP TS 25.304

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

3GPP TS 25.304

Uploaded by

Copyright:

Available Formats

3GPP TS 25.304 V7.8.

3GPP TS 25.304 V7.8.0 (2009-09)

3GPP Postal address

3GPP support office address

3GPP TS 25.304 V7.8.0 (2009-09)

General description of Idle mode.......................................................................................................10

Process and procedure descriptions ...................................................................................................14

3GPP TS 25.304 V7.8.0 (2009-09)

Broadcast information receiving........................................................................................................33

3GPP TS 25.304 V7.8.0 (2009-09)

3GPP TS 25.304 V7.8.0 (2009-09)

3GPP TS 25.304 V7.8.0 (2009-09)

[12] [13] [14] [15] [16] [17]

Definitions and abbreviations

3GPP TS 25.304 V7.8.0 (2009-09)

3GPP TS 25.304 V7.8.0 (2009-09)

3GPP TS 25.304 V7.8.0 (2009-09)

General description of Idle mode

The relationship between these processes is illustrated in Figure 1.

3GPP TS 25.304 V7.8.0 (2009-09)

PLMN selected NAS Control

Cell Selection and Reselection

Registration Area changes CM requests

Figure 1: Overall Idle Mode process

Functional division between AS and NAS in Idle mode

3GPP TS 25.304 V7.8.0 (2009-09)

Table 1: Functional division between AS and NAS in idle mode

Service type in Idle and Connected Mode

3GPP TS 25.304 V7.8.0 (2009-09)

Process and procedure descriptions

Support for PLMN Selection

3GPP TS 25.304 V7.8.0 (2009-09)

Support for network selection in GSM is described in [1].

Cell selection and reselection in idle mode

3GPP TS 25.304 V7.8.0 (2009-09)

States and state transitions in Idle Mode

Figure 2 shows the states and procedures in Idle Mode.

no suitable cell found

Init ial Cell Se lection

suitable cell f ound

suitable cell f ound no suitable cell f ound

Cell Selection w hen leaving connected mode

suitable cell f ound

return to idle mode

leave idle mode

trigger suitable cell f ound

Cell Reselection Evaluation Process

no suitable cell f ound go here w hen no US IM in the UE

no acceptable cell f ound

Any Cell Selection

acceptable cell f ound

Camped on any cell

suitable cell found

return to idle mode

leave idle mode

trigger acceptable cell found

Connected mode (Emergency calls only)

Cell Reselection Evaluation Process

no acceptable cell f ound