Orifice, Nozzle and Venturi Flow Rate Meters

Page 1 of 4

Resources, Tools and Basic Information for Engineering and Design of Technical Applications!
Flow Pressure Flow Meters
+2 Share this on Google+ Recommend 61

Water Meters Search

Orifice Fittings
Tweet

Custom Search

Home Acoustics Air Psychrometrics Basics Combustion Drawing Tools - 2D Schematic Drawings Dynamics Economics Electrical Environment Fluid Mechanics Gas and Compressed Air HVAC Systems - Air Conditioning - Heating - Noise and Attenuation - Ventilation Hydraulics and Pneumatics Insulation Material Properties Mathematics Mechanics - Beams and Columns Miscellaneous Physiology Piping Systems - Codes and Standards - Corrosion - Design Strategies - Dimensions - Fluid Flow and Pressure Drop - Heat Loss and Insulation - Pressure Ratings - Temperature Expansion - Valve Standards Process Control - Control Valves - Documentation - Fluid Flow Meters - Risk, Reliability and Safety - Temperature Measurement Pumps Standards Organizations Steam and Condensate - Control Valves and Equipment - Flash Steam - Heat Loss and Insulation - Pipe Sizing - Thermodynamics Thermodynamics Water Systems

Sponsored Links

Orifice, Nozzle and Venturi Flow Rate Meters

The orifice, nozzle and venturi flow rate meters use the Bernoulli Equation to calculate the fluid flow rate using pressure difference through obstructions in the flow
Sponsored Links

Water & Air Flowmeters

www.erdco.com Rotameter, Turbine & Thermal types for process, environmental & OEM's!
In a flow metering device based on the Bernoulli Equation the downstream pressure after an obstruction will be lower than the upstream pressure before. To understand orifice, nozzle and venturi meters it's therefore necessary to explore the Bernoulli Equation.

The Bernoulli Equation

Assuming a horizontal flow (neglecting minor elevation differences between measuring points) the Bernoulli Equation can be modified to: p1 + 1/2 v12 = p2 + 1/2 v22 where p = pressure = density v = flow velocity The equation can be adapted to vertical flow by adding elevation heights h1 and h2. Assuming uniform velocity profiles in the upstream and downstream flow - the Continuity Equation can be expressed as q = v1 A1 = v2 A2 where q = flow rate A = flow area Combining (1) and (2), assuming A2 < A1, gives the "ideal" equation: q = A2 [ 2(p1 - p2) / (1 - (A2 / A1)2) ]1/2 (3) (2) Free Industry Magazines Medical Design Briefs (1)

For a given geometry (A), the flow rate can be determined by measuring the pressure difference p1 - p2. The theoretical flow rate q will in practice be smaller (2 - 40%) due to geometrical conditions. The ideal equation (3) can be modified with a discharge coefficient: q = cd A2 [ 2(p1 - p2) / (1 - (A2 / A1)2) ]1/2 where cd = discharge coefficient The discharge coefficient cd is a function of the jet size - or orifice opening - the area ratio = Avc / A2 where Avionics Intelligence (3b) E&P (Hart's E&P)

Water Flow Air Flow Cross Flow

Convert Units
Temperature

Avc = area in "vena contracta" "Vena Contracta" is the minimum jet area that appears just downstream of the restriction. The viscous effect is usually expressed in terms of the nondimensional parameter Reynolds Number - Re. Due to the Benoulli and Continuity Equation the velocity of the fluid will be at it's highest and the pressure at the lowest in "Vena Contracta". After the metering device the velocity will decrease to the same level as before the obstruction. The pressure recover to a pressure level lower than the pressure before the obstruction and adds a head loss to the flow. Equation (3) can be modified with diameters to: q = cd /4 D22 [ 2(p1 - p2) / (1 - d4) ]1/2 where D2 = orifice, venturi or nozzle inside diameter D1 = upstream and downstream pipe diameter d = D2 / D1 diameter ratio (4)

0.0
o o

Engineering Standards

C F

Convert!
Length

1.0
m km in ft yards miles nautical miles

Convert!

http://www.engineeringtoolbox.com/orifice-nozzle-venturi-d_590.html

6/20/2013

Orifice, Nozzle and Venturi Flow Rate Meters

Page 2 of 4

Volume

= 3.14 Equation (4) can be modified to mass flow for fluids by simply multiplying with the density: m = cd /4 D22 [ 2(p1 - p2) / (1 - d4) ]1/2 (5)

1.0
m3 liters in3 ft3 us gal

Convert!
Velocity

When measuring the mass flow in gases, its necessary to considerate the pressure reduction and change in density of the fluid. The formula above can be used with limitations for applications with relatively small changes in pressure and density.

1.0
m/s km/h ft/min ft/s mph knots

The Orifice Plate

The orifice meter consists of a flat orifice plate with a circular hole drilled in it. There is a pressure tap upstream from the orifice plate and another just downstream. There are in general three methods of placing the taps. The coefficient of the meter depends upon the position of taps.

Convert!
Pressure

1.0
Pa (N/m2) bar mm H2O kg/cm2 psi inches H2O

Convert!
Flow

1.0
m3/s m3/h US gpm cfm

Convert!

Free Industry Magazines Medical Design Briefs

Flange location - Tap location 1 inch upstream and 1 inch downstream from face of orifice "Vena Contracta" location - Tap location 1 pipe diameter (actual inside) upstream and 0.3 to 0.8 pipe diameter downstream from face of orifice Pipe location - Tap location 2.5 times nominal pipe diameter upstream and 8 times nominal pipe diameter downstream from face of orifice The discharge coefficient - cd - varies considerably with changes in area ratio and the Reynolds number. A discharge coefficient cd = 0.60 may be taken as standard, but the value varies noticeably at low values of the Reynolds number. Discharge Coefficient - cd Diameter Ratio d = D2 / D1 Reynolds Number - Re 10
4

105 0.595 0.603 0.608 0.61 0.614

106 0.594 0.598 0.603 0.608 0.609

107 0.594 0.598 0.603 0.608 0.609

E&P (Hart's E&P)

0.2 0.4 0.5 0.6 0.7

0.60 0.61 0.62 0.63 0.64

The pressure recovery is limited for an orifice plate and the permanent pressure loss depends primarily on the area ratio. For an area ratio of 0.5, the head loss is about 70 - 75% of the orifice differential. Avionics Intelligence The orifice meter is recommended for clean and dirty liquids and some slurry services. The rangeability is 4 to 1 The pressure loss is medium Typical accuracy is 2 to 4% of full scale The required upstream diameter is 10 to 30 The viscosity effect is high The relative cost is low

References

Engineering Standards

American Society of Mechanical Engineers (ASME). 2001. Measurement of fluid flow using small bore precision orifice meters. ASME MFC-14M-2001. International Organization of Standards (ISO 5167-1:2003). Measurement of fluid flow by means of pressure differential devices, Part 1: Orifice plates, nozzles, and Venturi tubes inserted in circular crosssection conduits running full. Reference number: ISO 5167-1:2003. International Organization of Standards (ISO 5167-1) Amendment 1. 1998. Measurement of fluid flow by means of pressure differential devices, Part 1: Orifice plates, nozzles, and Venturi tubes inserted in circular cross-section conduits running full. Reference number: ISO 5167-1:1991/Amd.1:1998(E). American Society of Mechanical Engineers (ASME). B16.36 - 1996 - Orifice Flanges

The Venturi Meter

In the venturi meter the fluid is accelerated through a converging cone of angle 15-20o and the pressure difference between the upstream side of the cone and the throat is measured and provides a signal for the rate of flow.

http://www.engineeringtoolbox.com/orifice-nozzle-venturi-d_590.html

6/20/2013

Orifice, Nozzle and Venturi Flow Rate Meters

Page 3 of 4

The fluid slows down in a cone with smaller angle (5 - 7o) where most of the kinetic energy is converted back to pressure energy. Because of the cone and the gradual reduction in the area there is no "Vena Contracta". The flow area is at a minimum at the throat. High pressure and energy recovery makes the venturi meter suitable where only small pressure heads are available. A discharge coefficient cd = 0.975 can be indicated as standard, but the value varies noticeably at low values of the Reynolds number. The pressure recovery is much better for the venturi meter than for the orifice plate. The venturi tube is suitable for clean, dirty and viscous liquid and some slurry services. The rangeability is 4 to 1 Pressure loss is low Typical accuracy is 1% of full range Required upstream pipe length 5 to 20 diameters Viscosity effect is high Relative cost is medium

References

International Organization of Standards - ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices, Part 1: Orifice plates, nozzles, and Venturi tubes inserted in circular crosssection conduits running full. Reference number: ISO 5167-1:2003. American Society of Mechanical Engineers ASME FED 01-Jan-1971. Fluid Meters Their Theory And Application- Sixth Edition

The Nozzle
Nozzles used for determining fluid's flowrate through pipes can be in three different types: The ISA 1932 nozzle - developed in 1932 by the International Organization for Standardization or ISO. The ISA 1932 nozzle is common outside USA. The long radius nozzle is a variation of the ISA 1932 nozzle. The venturi nozzle is a hybrid having a convergent section similar to the ISA 1932 nozzle and a divergent section similar to a venturi tube flowmeter. Discharge Coefficient - cd Diameter Ratio d = D2 / D1 0.2 0.4 0.6 0.8 Reynolds Number - Re 104 0.968 0.957 0.95 0.94 105 0.988 0.984 0.981 0.978 106 0.994 0.993 0.992 0.991 107 0.995 0.995 0.995 0.995

The flow nozzle is recommended for both clean and dirty liquids The rangeability is 4 to 1 The relative pressure loss is medium Typical accuracy is 1-2% of full range Required upstream pipe length is 10 to 30 diameters The viscosity effect high The relative is medium

References

American Society of Mechanical Engineers ASME FED 01-Jan-1971. Fluid Meters Their Theory And Application- Sixth Edition International Organization of Standards - ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices, Part 1: Orifice plates, nozzles, and Venturi tubes inserted in circular crosssection conduits running full. Reference number: ISO 5167-1:2003.

Example - Kerosene Flow Through a Venturi Meter

The pressure difference dp = p1 - p2 between upstream and downstream is 100 kPa (1 105 N/m2). The specific gravity of kerosene is 0.82. Upstream diameter is 0.1 m and downstream diameter is 0.06 m. Density of kerosene can be calculated as: = 0.82 (1000 kg/m3) = 820 (kg/m3) Density, Specific Weight and Specific Gravity - An introduction and definition of density, specific weight and specific gravity. Formulas with examples. Upstream and downstream area can be calculated as: A1 = ((0.1 m)/2)2 = 0.00785 (m2) A2 = ((0.06 m)/2)2 = 0.002826 (m2) Theoretical flow can be calculated from (3): q = A2 [ 2(p1 - p2) / (1 - (A2/A1)2) ]1/2 q = (0.002826 m2) [ 2 (105 N/m2) / (820 kg/m3)(1 - ( (0.002826 m2) / (0.00785 m2) )2) ]1/2 = 0.047 (m3/s) For a pressure difference of 1 kPa (0,01x105 N/m2) - the theoretical flow can be calculated:

http://www.engineeringtoolbox.com/orifice-nozzle-venturi-d_590.html

6/20/2013

Orifice, Nozzle and Venturi Flow Rate Meters

Page 4 of 4

q = (0.002826 m2) [ 2 (0.01 105 N/m2) / (820 kg/m3)(1 - ( (0.002826 m2) / (0.00785 m2) )2) ]1/2 = 0.0047 (m3/s) The mass flow can be calculated as: m=q = (0.0047 m3/s) (820 kg/m3) = 3.85 (kg/s)

Flow Rate and Change in Pressure Difference

Note! - The flow rate varies with the square root of the pressure difference. From the example above: a tenfold increase in the flow rate requires a one hundredfold increase in the pressure difference!

Transmitters and Control System

The nonlinear relationship have impact on the pressure transmitters operating range and requires that the electronic pressure transmitters have the capability to linearizing the signal before transmitting it to the control system.

Accuracy
Due to the non linearity the turn down rate is limited. The accuracy strongly increases in the lower part of the operating range. More about Flow Meters as Orifices, Venturi meters, and Nozzles Fluid Mechanics The Bernoulli Equation The Continuity Equation TurnDown Ratio and Flow Measurement Devices - An introduction to Turn Down Ratio and flow measurement accuracy.
Sponsored Links

Duct Leakage Testing

www.oriflow.com Learn about duct leakage testing by the best in the business.

Search the Engineering ToolBox

Search
Custom Search

Related Topics
Fluid Flow Meters - Flow metering basics - Orifice, Venturi, Flow Nozzles, Pitot Tubes, Target, Variable Area, Positive Displacement, Turbine, Vortex, Electromagnetic, Ultrasonic Doppler, Ultrasonic Time-oftravel, Mass Coriolis, Mass Thermal, Weir V-notch, Flume Parshall and Sluice Gate flow meters and more Fluid Mechanics - The study of fluids - liquids and gases. Involves various properties of the fluid, such as velocity, pressure, density and temperature, as functions of space and time.

Related Documents
Equation of Continuity - The Equation of Continuity is a statement of mass conservation Flow of Liquids from Containers - Flow from tanks Flowmeters and Turndown Ratio - An introduction to turndown ratio for flow measurement devices as orifices, venturi meter etc. Nozzles - Gas flow through nozzles - sonic chokes Orifices - Air Discharge - Air volume through orifices

Engineering ToolBox - SketchUp Edition - Online 3D modeling!

Engineering ToolBox - SketchUp Edition - enabled for use with the amazing, fun and free Google SketchUp

Translate the ToolBox

Arabic - Chinese (Simplified) - Chinese (Traditional) - Dutch - French - German - Italian - Japanese - Korean Portuguese - Russian - Spanish - - Select Your own language . .

About the ToolBox

We appreciate any comments and tips on how to make The Engineering ToolBox a better information source. Please contact us by email editor.engineeringtoolbox@gmail.com if You find any faults, inaccuracies, or otherwise unacceptable information. The content in The Engineering ToolBox is copyrighted but can be used with NO WARRANTY or LIABILITY. Important information should always be double checked with alternative sources. All applicable national and local regulations and practices concerning this aspects must be strictly followed and adhered to.

Advertise in the ToolBox

If you want to promote your products or services in the Engineering ToolBox - please use Google Adwords.

http://www.engineeringtoolbox.com/orifice-nozzle-venturi-d_590.html

6/20/2013