Prefix Pro Blend
Prefix Pro Blend
Prefix Pro Blend
THE PICKUP
The system's under-saddle pickup is the industry standard Fishman Acoustic Matrix. It is made with Fishman's exclusive co-polymer sensing material. This proprietary material reproduces your acoustic guitar sound with a sensitivity and dynamic range that surpasses all other known materials (including piezo-ceramic and so called "piezo-film" pickups).
USER GUIDE
At the heart of the pickup is a multi-layer sandwich of co-polymer strips. These strips sense motion across the entire length of the saddle for unparalleled performance. Compared ceramic pickups with individual elements, the Acoustic Matrix' "unitary" co-polymer design provides a more natural and balanced response, with sensitivity to both the strings and the soundboard. The transducer is fully enclosed in a shielded foil wrap for dead quiet performance and total EMI noise rejection.
THE MICROPHONE
This quality electret-condenser microphone will provide very high level sound reproduction before feedback when used in conjunction with the unit's Phase, Notch and Contour EQ (see page x). Conveniently shock-mounted to the underside of the preamp chassis, the microphone is strategically isolated inside the instrument. For stage use, the Microphone's interior location affords you unprecedented freedom of movement as well as minimal bleed through from other instruments.
QUICK START
We recommend that you preset the system EQ to locate and eliminate microphone feedback before you mix in the under-saddle pickup. 1. Set all controls as follows: Notch and Volume fully counter-clockwise All EQ sliders at center position Blend slider at lowest position (B = microphone) 2. Slowly increase the volume and play the notes from the open low E, up to the fourth fret G sharp until the instrument starts to rumble or howl with feedback on one or more of these notes. Adjust the Notch control until this feedback is eliminated (usually between one and two o'clock on the dial).
SETUP
Battery Compartment
Pull the small tab at the top of the Onboard Blender toward you. The body of the preamp will swing out, revealing the battery compartment. Observe the polarity marks on the battery clip and install a fresh 9V alkaline battery accordingly.
USER GUIDE
Microphone Trim Control
A small circular potentiometer is located on the side of the preamp that faces the back of the guitar. This control can be accessed by opening the battery compartment. Set the Blend slider to the center position and with a small slotted screwdriver and adjust the Trim Control until both the microphone and pickup levels are balanced to your taste.
Endpin Jack
When you plug into the endpin jack, the Prefix Pro Blend switches on. To conserve the battery, remove the instrument cable from the endpin jack when the system is not being used. It is a good idea to turn down your amp or mixer input before you plug into the endpin jack. Doing so will protect your speakers (and your ears) from loud pops.
CONTROLS
Volume Control
This is a master volume control for both the pickup and the microphone. Set this as high as possible (without distorting your amp or mixer) for the cleanest signal.
Notch
Tune the Notch filter to scoop out the lowest range of feedback when you play bass notes between the open low E string and (up to and including) the forth fret G sharp on the same string. Low frequency "cavity resonance" feedback can usually be squelched by setting the Notch control between one o'clock and two o'clock on the dial. Note that for instruments that do not suffer from low frequency feedback, the notch can be defeated by moving the dial to the Off (seven o'clock) position.
Phase Switch
Flip the Phase switch back and forth until you find the position that sounds best and subdues mid-bass feedback. Mid-bass feedback generally occurs when you play bass notes above the fourth fret G sharp on the low E string.
Bass
This control affects the under-saddle pickup signal only! A Boost here will add depth and weight to the sound the instrument.
USER GUIDE
Contour EQ
The Contour slider and the Frequency knob make up this EQ. The Frequency knob lets you tune in on the specific range of sounds that you can boost/cut with the Contour (level) slider. With the Contour EQ you can boost or cut a wide range of frequencies, from gutsy low midrange (250 Hz) to brilliant high treble (10 kHz). Often your instrument will benefit from a slight midrange cut. To cut mids, boost the Contour control and then sweep the Frequency control until you find the band of frequencies that are brash and nasal sounding (usually around the middle center of the Frequency knob's travel). Then move the Contour slider below its detent to taste.
Treble
This control affects the under-saddle pickup signal only! A boost here will help to "cut through the mix". Conversely, cutting the Treble will mellow and subdue your amplified tone.
Blend Control
This control determines the balance between the two pickups. Move the slider left to emphasize the Microphone (B). Move it right to hear more of the Pickup (A).
USER GUIDE
SUGGESTED EQ SETTINGS
Anti-feedback
See Quick Start on Page 3
Brilliance
If you are playing through a limited range amplifier (like an electric guitar amp) or have dead strings on the instrument, you can brighten up your sound by setting the Frequency knob all the way to the right and raising the Contour (level) slider to taste. If you plan to play at high stage volume levels, dial in more pickup than microphone to avoid feedback.
Mid-Cut
You can scoop out harsh midrange by setting the Frequency knob at about 12:00 and the Contour (level) slider cut to taste below the center detent. Often the desired mid-cut will fall into the same frequency range as potential microphone feedback. You can also cut midrange (pickup only) by boosting the BASS and TREBLE sliders to realize an "implied" mid-cut at 800 Hz.
Fingerstyle
This setting will add fullness to the bass and definition to the treble.
10
USER GUIDE
SPECIFICATIONS
Nominal Input Level: Input Overload: Pickup Input Impedance: Output Impedance: Nominal Output Level: THD: Signal to Noise Ratio: -20 dBV (20 Hz - 20 kHz)-2 dBV 20 M Ohms Less than 3.5 k Ohms -12 dBV Less than .04 %, -20 dBV input 77 dB (A weighted referred to nominal -20 dBV input) Less than 4 mA 9V alkaline battery (estimated 140 hours continuous use with low battery indicator at 6.5V) 20Hz - 300 Hz (-15 dB) 12 dB at 60 Hz 3 dB at 350 Hz 12 dB at 10 kHz 3 dB at 2.4 kHz 12dB (adjustable from 250 Hz to 10 kHz) Q = 0.5
Notch Filter Range: Bass Control Range: Treble Control Range: Contour Control Range:
11
Limited Warranty
The Fishman Prefix Pro Blend is warranted to function for a period of One (1) Year from the date of purchase. If the unit fails to function properly within the warranty period, free repair and the option of replacement or refund in the event that Fishman is unable to make repair are Fishmans only obligations. This warranty does not cover any consequential damages or damage to the unit due to misuse, accident, or neglect. Fishman retains the right to make such determination on the basis of factory inspection. Products returned to Fishman for repair or replacement must be shipped in accordance with the Return Policy, as follows. This warranty remains valid only if repairs are performed by Fishman. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
Return Policy
To return products to Fishman Transducers, you must follow these steps... 1. Call Fishman Transducers at 978-988-9665 for a Return Authorization Number (RAN). 2. Enclose a copy of the original Bill of Sale as evidence of the date of purchase, with the product in its original packaging and a protective carton or mailer. 3. Fishman Transducers technicians will determine whether the item is covered by warranty or if it instead has been damaged by improper customer installation or other causes not related to defects in material or workmanship. 4. Warranty repairs or replacements will be sent automatically free of charge. 5. If Fishman Transducers determines the item is not covered by warranty, we will notify you of the repair or replacement cost and wait for your authorization to proceed.
FISHMAN TRANSDUCERS
340-D Fordham Road Wilmington MA 01887 USA Phone 978-988-9199 Fax 978-988-0770 www.fishman.com
009-089-005 1-01