Scaffold Safety Guide

A Guide to
Scaffolding
Safety
January 2006
Copyright notice
This publication is based on the Victoria WorkSafe publication “Guidance Note –

Fall Prevention for Scaffolders”. The graphics in this publication are sourced
from the QLD Department of Industrial Relations.
Disclaimer
This document provides general information about the rights and obligations of
employees and employers under ACT occupational health and safety laws.
It is intended to provide general information about the law and is not intended to
represent a comprehensive statement of the law as it applies to particular
problems or to individuals, or substitute for legal advice.
You should seek independent legal advice if you need assistance on the
application of the law to your situation.
January 2006
SCAFFOLDING SAFETY
CONTENTS
Introduction ………………………………………………………………………… 2
Overview of Scaffolding Injuries ………………………………………. 3
Overview of Scaffolding Injuries and Fatalities (2003-04) 3
Controlling the Risk of Internal Falls……………………………….. 3

Fully Decking Each Lift 3
Advantages 4
Precautions 5
Controlling the Risk of External Falls ……………………………….. 6
Sequential Erection 6
Controlling the Risk of Climbing Falls with Safe Access

Systems…………………………………………………………………………….….. 7
Summary 7
Fall Arrest & Travel Restraint Systems for Scaffolders ….… 8
Safety Harness 8
Further Information …………………………………………………………..… 12
1
SCAFFOLDING SAFETY
Introduction
Scaffolding is defined as the erection, alteration or
dismantling of a temporary structure, specifically erected to
support platforms. 1
Scaffolds are commonly used for working at heights and there

is the potential risk for a scaffolder (person working on a
scaffold) to fall from an incomplete scaffold during the
erection and dismantling of a scaffold.
In particular, scaffolders can be exposed to fall hazards:
• during the placement or removal of scaffold plants

(internal fall)
• from the open sides or ends of the scaffold (external fall)
• in climbing from one lift of the scaffold to the next lift

(climbing fall).
This guide will help you to identify some of the potential

risks and provides solutions and tips for fall protection when
erecting, dismantling or altering scaffolding, to help reduce
injuries and fatalities resulting from working unsafely on
scaffolds.
1
NOHSC Standard for Users and Operators of Industrial Equipment [NOHSC 1006(2001)]
– 3rd Edition
2
SCAFFOLDING SAFETY
Overview of Scaffolding Injuries

Overview of Scaffolding Injuries and Fatalities
(2003-04)
• Falls from a height – 26%

• Falls on the same level - 15%
Controlling the Risk of Internal Falls

Fully Decking Each Lift
The risk of internal falls while erecting a scaffold can be

controlled by fully decking each lift.
This involves:
• positioning a full deck of planks at each lift
• positioning planks on the next lift whilst standing on a

full-decked platform and
• leaving each lift fully decked in place until it is

dismantled.
During dismantling a lift, planks are removed while standing

on the full-decked platform immediately below.
3
SCAFFOLDING SAFETY
Advantages
By adopting this method:
• Scaffolders working aloft cannot fall through the

scaffold.
• Principal contractors can authorise work from any given

lift of the scaffold without the time delay and expense of
having working platforms relocated from one lift to
another.
Note: all platforms will require full edge protection

(guardrails-midrails-toeboards or quardrails-brickguards)
to enable such authorisation.
• Shade cloth and other types of containment sheeting can

be installed safely and easily.
Access to scaffolds for routine inspections is improved.
4
SCAFFOLDING SAFETY
Precautions
Precautions associated with this method include:
• The scaffold design must be checked to ensure that

the placement of a full deck at each lift will not
adversely affect the working capacity of the scaffold’s
standards and/or supporting structure.
• Decks on non-working lifts must be physically closed

off and signposted to prevent their inadvertent use,
where the number of fully decked lifts exceeds the
number of simultaneously used and/or loaded working
platforms that the scaffold can safely support.
• Where the provision of additional decks of planks

involves hazardous manual handling tasks, a risk
assessment must be conducted and appropriate control
measures must be implemented. Control measures
should be, in the first instance, mechanical aids such
as cranes, hoists or forklifts. Where this is not
reasonably practicable, consideration should be given
to other measures such as increased gang sizes, job
rotation or additional breaks.
5
SCAFFOLDING SAFETY
Controlling the Risk of External Falls

Sequential Erection
The risk of external falls from the open sides and ends of the
scaffold can be reasonably controlled by adopting the sequential
erection method.
This method involves the one-bay-at-a-time sequential

installation of standards and guardrails (or guardrails alone
where standards are already in place). This ensures that
scaffolders are not required to walk further than one bay length
along an exposed edge of a scaffold platform. Dismantling is
simply a reverse of the sequence.
It should be noted that where platform brackets

(“hop-ups”) are to be installed later, where the adjacent
structure is yet to be built or in other similar circumstances,
internal guard rails should also be installed as part of the above
sequence.
The use of the sequential erection method does not preclude

the use of alternative methods such as purpose-designed
proprietary advance guardrail systems or other systems of
work that provide an equivalent level of fall protection.
The particular method selected to control the risk of external

falls will depend upon the relative feasibility of its
application to the scaffold configuration being considered.
6
SCAFFOLDING SAFETY
Controlling the Risk of Climbing Falls with

Safe Access Systems
Ensuring that an appropriate access system is in place can
control the risk of climbing falls for scaffolders gaining
access from one lift to the next. This can be in the form of
a stairway or ladder access that is progressively installed as
the scaffold is erected, rather than added on at a later
stage.
Employers should ensure that the practice of scaffolders

climbing the scaffold framework is strictly forbidden.
Summary
The three typical situations where scaffolders can be

exposed to a risk of a fall (internal, external and climbing)
can be reasonably controlled by a combination of fully
decking each lift, using the sequential erection method and
progressively providing access as the scaffold is erected.
7
SCAFFOLDING SAFETY
Fall Arrest & Travel Restraint Systems for

Scaffolders
Safety Harness
The use of a safety harness as a fall injury prevention system

has limited practical application for the construction of
scaffolds. A harness should not be used where:
• it is possible for scaffolders to hit an object prior to their

fall being arrested (See Figure 1)
• its use would restrict the scaffolder’s free movement so

as to increase the risk of sprain or strain injuries.
• its use would present a risk of scaffold components

becoming entangled or unbalanced during handling.
• there is no adequate and correctly positioned anchorage

for lanyards or inertia reels.
NOTE: Safety harnesses should not be used in the erection

and dismantling of normal standing scaffolds.
8
SCAFFOLDING SAFETY
ACCEPTABLE
Structural Beams
Fall arrest inertia reel

with energy absorber
End of fall (no

contact with
structure)
Figure1: Appropriate use of a harness system in the erection and

dismantling of a hung scaffold.
9
SCAFFOLDING SAFETY
Safety harness systems would be an acceptable control

solution in the following situations when erecting or
dismantling scaffolds:
• On hung scaffolds, where the scaffold is constructed from

top to bottom and there is nothing for the scaffolder to
strike below in the event of a fall (see Figure 1).
• On cantilevered needles (for the erection of the first lift

and later for dismantling that lift) and for decking
between the needles.
• When attaching and removing spurs that project from the

supporting scaffold or supporting structure.
• When fixing and removing trolley tracks on suspension

rigs. (A trolley track is a suspended rail that supports
and guides trolleys for swing stages, work cages,
boatswain’s chairs and other types of suspended
scaffolding).
NOTE: If harness systems are used, in all instances a

scaffolder must not be exposed to a fall prior to being
securely connected to, or after being disconnected from the
anchorage point.
10
SCAFFOLDING SAFETY
UNACCEPTABLE
Anchorage point
(note: scaffold
tube will not
have adequate
capacity - min
15 kilonewtons)
2 metre lanyard
Energy
absorber
End of fall –
worker strikes
transom
Figure2: Why harnesses are not acceptable for normal scaffolding

work (ie. scaffolds built from the ground up).
11
SCAFFOLDING SAFETY
Further Information
Occupational Health and Safety Act 1989 (the Act)
Scaffolding and Lifts Act (1912)
Scaffold and Lifts Regulations 1950
ACT WorkCover Information Bulletin - Scaffolding 04.16
ACT WorkCover Information Bulletin - Falls Prevention on

Construction Sites 3.14
ACT WorkCover Steel Construction Code of Practice, April

1997
AS/NZS 4576 – Guidelines for Scaffolding, available from

Standards Australia at www.standards.com.au or telephone
on 1300654 646
ACT WorkCover website: www.workcover@act.gov.au
12
SCAFFOLDING SAFETY
Notes
13
SCAFFOLDING SAFETY
Level 4, Eclipse House

197 London Circuit
Canberra City ACT 2600
www.workcover.act.gov.au
PO Box 224,
Civic Square, ACT 2608
Ph. 6205 0200

Fax. 6205 0366
E-mail: workcover@act.gov.au
ACT Government

Scaffold Safety Guide

Uploaded by

Copyright:

Available Formats

Scaffold Safety Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Scaffold Safety Guide

Uploaded by

Copyright:

Available Formats

A Guide to

This publication is based on the Victoria WorkSafe publication “Guidance Note –

Overview of Scaffolding Injuries and Fatalities (2003-04) 3

Controlling the Risk of Internal Falls……………………………….. 3

Controlling the Risk of Climbing Falls with Safe Access

Scaffolds are commonly used for working at heights and there

In particular, scaffolders can be exposed to fall hazards:

• during the placement or removal of scaffold plants

• from the open sides or ends of the scaffold (external fall)

• in climbing from one lift of the scaffold to the next lift

This guide will help you to identify some of the potential

Overview of Scaffolding Injuries

• Falls from a height – 26%

Controlling the Risk of Internal Falls

The risk of internal falls while erecting a scaffold can be

• positioning a full deck of planks at each lift

• positioning planks on the next lift whilst standing on a

• leaving each lift fully decked in place until it is

During dismantling a lift, planks are removed while standing

• Scaffolders working aloft cannot fall through the

• Principal contractors can authorise work from any given

Note: all platforms will require full edge protection

• Shade cloth and other types of containment sheeting can

Access to scaffolds for routine inspections is improved.

• The scaffold design must be checked to ensure that

• Decks on non-working lifts must be physically closed

• Where the provision of additional decks of planks

Controlling the Risk of External Falls

This method involves the one-bay-at-a-time sequential

It should be noted that where platform brackets

The use of the sequential erection method does not preclude

The particular method selected to control the risk of external

Controlling the Risk of Climbing Falls with

Employers should ensure that the practice of scaffolders

The three typical situations where scaffolders can be

Fall Arrest & Travel Restraint Systems for

The use of a safety harness as a fall injury prevention system

• it is possible for scaffolders to hit an object prior to their

• its use would restrict the scaffolder’s free movement so

• its use would present a risk of scaffold components

• there is no adequate and correctly positioned anchorage

NOTE: Safety harnesses should not be used in the erection

Fall arrest inertia reel

End of fall (no

Figure1: Appropriate use of a harness system in the erection and

Safety harness systems would be an acceptable control

• On hung scaffolds, where the scaffold is constructed from

• On cantilevered needles (for the erection of the first lift

• When attaching and removing spurs that project from the

• When fixing and removing trolley tracks on suspension

NOTE: If harness systems are used, in all instances a

Figure2: Why harnesses are not acceptable for normal scaffolding

Occupational Health and Safety Act 1989 (the Act)

Scaffolding and Lifts Act (1912)

Scaffold and Lifts Regulations 1950

ACT WorkCover Information Bulletin - Scaffolding 04.16

ACT WorkCover Information Bulletin - Falls Prevention on

ACT WorkCover Steel Construction Code of Practice, April

AS/NZS 4576 – Guidelines for Scaffolding, available from

ACT WorkCover website: www.workcover@act.gov.au