Relay Settings Tables - 12mar12

HT MOTOR RELAY SETTINGS TABLE Motor Feeder Feeder (breaker) Rating (Motor Feeder) Relay / Release Make Alstom
Relay / Release Type MiCOM P241
JOB NO : CLIENT : DOC NO : REV NO : Range Available
DATE : Remarks
Breaker No.
Panel No
Feeder CT Ratio Nos 400/5A
Setting Function Rated current Rated frequency Line CT Primary Line CT Secondary Line VT Primary Line VT Secondary
Setting Parameter
Recommended Settings 5A 50Hz 400A 5A 6600 Volt 110 Volt
IN fN
1 or 5A 50 or 60Hz
Ith> K Coefficient Thermal constant T1 Thermal constant T2 Thermal constant Tr Thermal Trip Thermal Alarm Alarm Threshold Thermal Lockout Lockout Thresh Inh Trip Dur St
0.2 to 1.5 In 0 to 10 1 - 180 min. 1 - 360 min. 1 - 999 min. Disabled/Enabled Disabled/Enabled 0.2% to 100% Disabled/Enabled 0.2% to 100% Disabled/Enabled
0.82 In 2 20 min. 20 min. 100 min. Enabled Enabled 80% Enabled 20% Disabled
Thermal Overload Protection (49)
Page 1 of 5
HT MOTOR RELAY SETTINGS TABLE Motor Feeder Feeder (breaker) Rating Relay / Release Make Relay / Release Type
JOB NO : CLIENT : DOC NO : REV NO : Range Available Disabled, DT, IEC S Inverse, IEC V Inverse, IEC E Inverse, UK LT Inverse, UK Rectifier, RI, IEEE M Inverse, IEEE V Inverse, IEEE E Inverse, US Inverse, US ST Inverse 0.2 to 15 In 0.04 to 100 0.025 to 1.2 0.01 to 100 0.1 to 10 DT/Inverse 0.0 to 100 Disabled/Enabled 0.2 to 15 In 0.04 to 100
DATE : Remarks
Breaker No.
Panel No
Feeder CT Ratio Nos
Setting Function
Setting Parameter
Recommended Settings
I>1 Fuction
DT
I>1 Current set Short circuit protection I>1 Time Dealy I>1 TMS I>1 Time Dial I>1 K (RI) I>1 Reset Charac. I>1 t RESET I>2 set as I>1 I>3 Status I>3 Current set I>3 Time Dealy I>4 Set as I>3
4.3 0.05 DT 0 Disabled Disabled Disabled
Page 2 of 5
JOB NO : CLIENT : DOC NO : REV NO : Range Available
DATE : Remarks
Breaker No.
Panel No
Feeder CT Ratio Nos
Setting Function
Setting Parameter
Recommended Settings
Blocked Rotor Protection (50 L/R)
I> Time Delay (T)
1-5 x 49 Pickup 0.1 - 60 sec
3.5 11.5
ISEF>1 Fuction
Earth Fault Protection ISEF>1 Current ISEF>1 Time Delay ISEF>1 TMS ISEF>1 Time dial ISEF>1 Reset Charac ISEF>1 tReset ISEF>2 Fuction V<1 Function Under voltage protection [27] V<1 Voltage set V< 1 Time delay V<1 TMS V<2 Status
Disabled, DT, IEC S Inverse, IEC V Inverse, IEC E Inverse, UK LT Inverse, UK Rectifier, RI, IEEE M Inverse, IEEE V Inverse, IEEE E Inverse, US Inverse, US ST Inverse 0.005 to 1 In 0.04 - 200 s 0.025 to 1.2 0.5 to 15 DT/Inverse 0 to 100 sec Disabled/Enabled Disabled/DT/IDMT 15 - 120 V 0.04 - 7200 S 0.05 - 100 Disabled/DT
DT
0.076 0.1 DT 0 Disabled DT 88 5 Disabled
Page 3 of 5
JOB NO : CLIENT : DOC NO : REV NO : Range Available Disabled/DT/IDMT 50 - 200 V 0.04 - 7200 S Disabled/DT Disabled / DT 0.05 to 0.8 In 0.04 - 200 s Disabled / IMDT Disabled / DT 45.65 Hz 0.1 - 100 s Disabled / IMDT 45.65 Hz 0.1 - 100 s 1In - 120In W 0.04 - 100 sec 0.05 - 300 sec Disabled / Enabled 15 - 75 0.00 - 100.0 sec Disabled / Enabled 0 - 40.0/In 25 - 325.0/In 0 - 100 sec 0 - 100 sec Disabled / Enabled 0 - 40.0/In 25 - 325.0/In
DATE : Remarks
Breaker No.
Panel No
Feeder CT Ratio Nos
Setting Function Over voltage protection [59] Negative sequence overcurrent (46)
Setting Parameter V> Status V>1 Voltage Set V< 1 Time delay V>2 Status I2>1 Status I2>1 Current I2>1 Time delay I2>2 Status F<1 Status F<1 Setting
Recommended Settings DT 126.5 5 Disabled DT 0.44 In 10 Disabled DT 48.5 5 DT 51.5 5 10In 5 17 Enabled 25 12 Enabled 38 67.3 10 0 Disabled -
Under Frequency (81)
F<1 Time delay F<2 Status F<2 Setting F<2 Time delay Rev P < Power set Rev P < Time delay Rev P < Drop-of time FFail Alarm status FFail Alarm angle FFail Alarm delay FFail 1 status FFail 1 -Xa1 FFail 1 -Xb1 FFail 1 Time delay FFail 1 DO Timer FFail 2 status FFail 2 -Xa1 FFail 2 -Xb1
Reverse power relay (32)
Field failure relay (40)
Page 4 of 5
Field failure SETTINGS TABLE HT MOTOR RELAY relay (40) Feeder Motor Feeder (breaker) Rating Relay / Release Make Relay / Release Type
JOB NO : CLIENT : DOC NO : REV NO : Range Available 0 - 100 sec 0 - 100 sec Disabled / DT 0.1 - 0.9 0.05 - 100 sec Disabled / DT 0.1 - 0.9 0.05 - 100 sec 0.05 - 300 sec
DATE : Remarks
Breaker No.
Panel No
Feeder CT Ratio Nos
Setting Function
Setting Parameter FFail 2 Time delay FFail 2 DO Timer PF<Status Lead Power Fact lead
Recommended Settings DT 0.9 50 msec DT 0.9 50 msec 17
Out of step protection (78)
PF < Lead TD PF<Status Llag Power Fact lag PF < Lag TD PF < Drop-off time
Page 5 of 5

Relay Settings Tables - 12mar12

Uploaded by

Copyright:

Available Formats

Relay Settings Tables - 12mar12

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Relay Settings Tables - 12mar12

Uploaded by

Copyright:

Available Formats

HT MOTOR RELAY SETTINGS TABLE Motor Feeder Feeder (breaker) Rating (Motor Feeder) Relay / Release Make Alstom

Relay / Release Type MiCOM P241

JOB NO : CLIENT : DOC NO : REV NO : Range Available

Feeder CT Ratio Nos 400/5A

Recommended Settings 5A 50Hz 400A 5A 6600 Volt 110 Volt

Thermal Overload Protection (49)

Feeder CT Ratio Nos

4.3 0.05 DT 0 Disabled Disabled Disabled

JOB NO : CLIENT : DOC NO : REV NO : Range Available

Feeder CT Ratio Nos

Blocked Rotor Protection (50 L/R)

I> Time Delay (T)

1-5 x 49 Pickup 0.1 - 60 sec

0.076 0.1 DT 0 Disabled DT 88 5 Disabled

Feeder CT Ratio Nos

Under Frequency (81)

Reverse power relay (32)

Field failure relay (40)

Feeder CT Ratio Nos

Recommended Settings DT 0.9 50 msec DT 0.9 50 msec 17

Out of step protection (78)

You might also like