O Ring Brochure

Specialists in Seals & Service
O-Ring Sizing and Materials Guide

Contains ISO 3601 Information
Kalrez
Choose Kalrez O-rings for the most harsh sealing conditions.
What makes Kalrez a superior elastomer?

Kalrez materials have virtually universal chemical resistance
Minimum swell
Reduce fugitive emissions
Service temperature range up to 327C
Maintains sealing force to better then most other materials
Low compression set
Longer seal life
Kalrez can save your company money through increased production cycle time and
reduced damage to your equipment.
Specialists in Seals & Service
Table of Contents
Hi-Tech Seals Inc. Compound Specifications
Machining Specifications
O-Ring Gland Types
Selecting an O-Ring Cross-Section
Groove Details
Extrusion Gap
ID Stretch/OD Interference
Reduction in Cross-Section
Compression
Gland Fill
O-Ring Sizing Charts
000 Series
100 Series
200 Series
300 Series
400 Series
O-Rings for Tube Fittings
Tolerance for Non-Standard O-Rings
Metric Application Gland Dimensions
Face Seal Glands
Dynamic Reciprocating Applications
Static Radial Applications
Common O-Ring Failures
Materials Guide
1
2
3
3
3
4
6
7
8
8
9
10
10
12
15
18
21
23
24
25
25
26
27
28
32
Table of Contents
Table of Contents
Hi-Tech Seals - Popular Compound Specification Guide
Compound Specifications
Service
-40 C to 120 C
A general service Nitrile compound for a wide range of applications

including petroleum based fluids. Nitrile compounds also have excellent
resistance to compression set, tear and abrasion resistance.
Elastomer Type
Durometer
N70
Nitrile
70 +/- 5
N90
Nitrile
90 +/- 5
-25 C to 120 C
70 +/- 5
-55 C to 120 C
-67 F to 248 F
A low temperature Nitrile compound for use in applications where

sealability at lower temperatures is important. Due to the lower
acrylonitrile content, this compound will show slightly less resistance to
petroleum products.
LTN
Temperature
Range
Compound
Nitrile
-40 F to 248 F
-13 F to 248 F
Generally used for higher pressures than the 70 durometer materials,

while having comparable media resistance.
HS7
Highly Saturated
Nitrile
70 +/- 5
-40 C to 150 C
-40 F to 302 F
This is a hydrogenated Nitrile compound which provides the material

with improved resistance to heat, ozone and aging. Similar applications
to Nitrile but with improved mechanical properties and media resistance.
Excellent for many oilfield and automotive applications. H2S resistance
up to 10%.
HS8
Highly Saturated
Nitrile
80 +/- 5
-40 C to 150 C
-40 F to 302 F
Generally used for higher pressures than the 70 durometer materials

HS9
Highly Saturated
Nitrile
90 +/- 5
-40 C to 150 C
-40 F to 302 F

while having comparable media resistance. Improved ED resistance.
Genuine Viton compounds have excellent resistance to ozone,
weather, oxygen, mineral oil, fuels, hydraulic fluids, aromatics, petroleum
fluids, many organic solvents and chemicals. Viton is also used in high
temperature applications.
Viton Extreme TBR and ETP compounds are also available.
TBR- Totally Base Resistant compound that provides improved
performance over other TFE/Propylene polymers.
ETP- Provides the excellent thermal resistance of Viton along with
significantly advanced chemical resistance.
V75
Viton
75 +/- 5
-25 C to 204 C
-13 F to 400 F
V90
Viton
90 +/- 5
-25 C to 204 C
-13 F to 400 F
Genuine Viton is generally used for higher pressure than the 75

durometer materials while having comparable media resistance.
LTV
Viton GLT
75 +/- 5
-40 C to 204 C
-40 F to 400 F
Genuine Viton GLT is used for lower temperature applications than the
75 durometer materials while having comparable media resistance.
PF7
Perfluoroelastomer
75 +/- 5
-15 C to 300 C
5 F to 572 F
Perfluroelastomer materials combine the best heat and chemical

resistance performance compared to other elastomer materials.
PF9
Perfluoroelastomer
90 +/- 5
-4 C to 230 C
25 F to 466 F

A80
Aflas
80 +/- 5
0 C to 230 C
32 F to 446 F
Tetrafluoroethylene-Propylene materials exhibit exceptional thermal and

chemical resistance including hot water, steam, acids, alkaline solutions,
ammonia, amines, brake fluids, petroleum fluids and sour gas. Low
temperature may restrict sealing abilities.
NEO
Neoprene
70 +/- 5
Neoprene is a general purpose material for refrigerants, ozone and

weather.
E70
EthylenePropylene
70 +/- 5
-45 C to 135 C
-49 F to 275 F
-54 C to 150 C
-65 F to 302 F
E80
EthylenePropylene
80 +/- 5
-54 C to 150 C
Generally used for higher pressures than 70 durometer EPDM

compounds while having comparable media resistance.
S70
Silicone
70 +/- 5
-55 C to 230 C
FS7
Fluorosilicone
70 +/- 5
-55 C to 200 C
-67 F to 392 F
-65 F to 302 F
-67 F to 446 F
Ethylene-Propylene materials exhibit excellent resistance to water,

steam, brake fluids and ozone.
Silicone compounds offer the widest elastomer temperature range but

typically can not be used in dynamic applications or petroleum based
fluids.
Fluorosilicone for use in petroleum and synthetic oils, greases, amines,
amine-treated hydrocarbons and steam.
F.D.A., NSF and UL listed or approved materials available upon request. We also offer a complete range of coloured or internally lubed compounds as required. Some materials are
available in durometers that range from 40 to 95 shore A. Most compounds available in metric sizing.
Hi-Tech Seals Inc. also offers a complete range of back-up rings, anti-extrusion devices as well as X-rings and square cut rings. These products are available in a variety of sizes and
materials, please contact your sales office for more information.
O-Ring Gland Types
O-rings are primarily used to prevent the loss of a fluid or gas. However, O-rings can be used as
dust seals, drive belts or on rotating shafts. Most O-ring seals can be classified into one of the three
arrangements shown below.
Rod Configuration
Face Type Configuration
Selecting an O-Ring Cross-Section
Piston Configuration
Whereas the ID or OD of the O-ring for a design is significantly influenced by the diameter of the
mating components (piston/rod and bore), the cross-section of the O-ring is usually fairly arbitrary.
The following table describes some of the advantages when opting for a small cross-section or a
large cross-section.
Advantages of Smaller Cross-Section
More compact
Lighter weight
Less expensive; especially for higher cost
elastomers like FKM or fluorosilicone

Less machining required for machined grooves
since grooves are smaller
More resistant to explosive decompression
Advantages of Larger Cross-Section

Less prone to compression set
Less volume swell in liquid on a percentage
basis
Allows for larger tolerance while still
maintaining acceptable compression squeeze

and compression ratio over full stack-up range
Less prone to leakage due to contamination;
dirt, lint, scratches, etc.
Groove Details
Piston Detail
Rod Detail
c
c
a- wall angle b- break edge c- radius d- angle e- chamfer length

O-Ring
Series
O-Ring C/S
Inch
mm
0.070
1.78
100
0.103
2.62
200
0.139
3.53
300
0.210
5.33
400
0.275
6.99
0.004-0.012
Inch
0-5
0.10-0.30
mm
ce
a at 15-d
-d at 20-
Inch
mm
Inch
mmb
Inch
mm
0.008-0.016
0.20-0.40
0.043
1.10
0.035
0.90
d
0.008-0.016
0.20-0.40
0.059
1.50
0.043
1.10
0.016-0.031
0.40-0.80
0.071
1.80
0.055
1.40
0.016-0.031
0.40-0.80
0.106
2.70
0.083
2.10
0.031-0.047
0.80-1.20
0.142
3.60
0.110
2.80
The surface roughness of the O-ring housing and any mating part has a significant impact on the life
and sealing performance of the O-ring. The following are surface roughness values in micrometers
(m):
For a static mating surface: Ra 1.6 / Rz 6.3
For a dynamic mating surface: Ra 0.4 / Rz 1.6
For more information on surface finish values, please contact Hi-Tech Seals Inc. engineering.
O-Ring
Series
b2
O-Ring C/S
Inch
mm
O-Ring C/S Squeeze (%)

HD
PD
HPS
b3
b1
b2
Inch
+ 0.010
- 0.000
/ mm
+ 0.25
- 0.00
b3
0.070
1.78
13-27
10-24
14-35
0.110/2.80
0.165/4.20
0.220/5.60
100
0.103
2.62
12-24
8-22
13-30
0.150/3.80
0.205/5.20
0.260/6.60
200
0.139
3.53
11-22
7-20
13-30
0.197/5.00
0.252/6.40
0.307/7.80
300
0.210
5.33
11-20
7-18
12-28
0.283/7.20
0.354/9.00
0.429/10.90
400
0.275
6.99
9-19
6-17
10-25
0.374/9.50
0.484/12.30
0.594/15.10
HD- Hydraulic Dynamic Applications

PD- Pneumatic Dynamic Applications
HPS- Hydraulic & Pneumatic Static Applications
Note: For piston applications, b1, b2 and b3, values do not apply for 001-003 and 400-424 series
O-rings.
Note: For rod applications b1, b2 and b3 values do not apply for 001-003, 028-050, 135-178, 232-284,
350-395, 400-424 and 430-475.
b1
Extrusion Gap
Extrusion is a concern for radial seals where there is gap between the piston and the bore for a piston
type seal or between the rod and the bore for a rod type seal. It is not typically a concern for face
type seals where the metal parts to be sealed are in contact line-to-line. The issue is that at higher
pressures and especially for softer O-ring elastomers, the O-ring can be forced by the pressure into
the small gap between the piston (or rod) and the bore. Unless the bore and the piston (or rod) are
ensured to remain concentric by the hardware, we have to assume that entire possible gap can shift
to one side (see diagram below).
Piston Type Seal
Extrusion Gap= Bore 0- Piston 0
Rod Type seal

Extrusion Gap = Bore 0- Rod 0
Concentricity & Diametral Clearance
A= Radial Gap
B= Diametrical Gap
Maximum Possible Extrusion Gap
Extrusion
Gap
High
Pressure
* Extrusion gaps should always be based on maximum diametral gap.
NOTE: The chart on the right is not to ISO

specification, it is meant to be used as a
reference guide.
690.0
552.0
LIMITS FOR EXTRUSION
10000
8000
414.0
6000
276.0
4000
207.0
3000
138.0
2000
EXTRUSION
69.0
55.2
1000
800
41.4
27.6
600
NO
EXTRUSION
400
20.7
300
13.8
200
6.9
mm 0
In.
0
.3
.5
.8
1.0
.010
.020
.030
.040
DUROMETER
(HARDNESS SHORE A)
- 70
- 80
- 90
Total Diametral Clearance *

(Radial Clearance if Concentricity Between
Piston and Cylinder is Rigidly Maintained)
*Reduce the clearance shown by 60% when
using silicone or fluorosilicone elastomers.
100
Fluid Pressure (psi)
There are different methods to counter O-ring

extrusion. One of these methods is to simply
increase the durometer rating of the O-ring.
However, as you increase the durometer, the
O-ring can become less malleable. Another
option would be the use of anti-extrusion
devices. These are thin rings made of hard
plastic materials such as PTFE, Nylon, and PEEK.
Once in place these ring will provide essentially
zero clearance.
Fluid Pressure (Bar)
Extrusion
ID Stretch/OD Interference
For hydraulic and pneumatic rod sealing applications

The O-ring outside diameter (d1 + 2d2) should be at least equal to or larger than the housing outside
diameter, d4, to give interference on the outside diameter. The O-ring outside diameter should not
exceed 3% of the housing outside diameter for O-rings with a diameter d1, greater than 250 mm,
or 5% for O-rings with a diameter d1 smaller than 250 mm. For O-rings with a diameter d1 smaller
than 20 mm, this is not always possible due to tolerance issues, which can result in a greater outside
diameter interference.
For hydraulic and pneumatic static axial sealing applications
An O-ring is compressed in the axial direction. An O-ring can be pressurized from an internal or
external source. A proper housing design minimizes the number of gaps through which the O-ring
can extrude and reduces potential damage to the O-ring during assembly. In this case the following
housing dimensions apply:
O-Ring C/S
O-Ring
Series
Inch
mm
0.070
100
+0.008/-0.000 w +0.20/-0.00
Liquid Applications
Gas/Vacuum Applications
+0.004/-0.000
(Inch/mm)
Inch
mm
1.78
0.126/3.20
0.114/2.90
0.051
1.30
0.103
2.62
0.157/4.00
0.142/3.60
0.079
2.00
200
0.139
3.53
0.209/5.30
0.189/4.80
0.106
2.70
300
0.210
5.33
0.299/7.60
0.276/7.00
0.165
4.20
400
0.275
6.99
0.354/9.00
0.335/8.50
0.224
5.70
(Inch/mm)
+0.10/-0.00
For hydraulic and pneumatic piston sealing applications

The nominal O-ring inside diameter, d1, should be stretched between 2% and 5% for dynamic
applications and 2% and 8% for static applications. For O-rings with a diameter d1 smaller than 20
mm, this is not always possible which can result in a wider range of stretch. To minimize this range
and the maximum stretch, it is necessary to minimize the tolerance of the housing diameter, d3,
and have a less stringent requirement for the minimum O-ring stretch. In dynamic applications,
it is important to keep the maximum stretch to 5% or less to avoid detrimental effects on sealing
performance.
w- width of the O-ring axial housing, h- height of the seal housing
0 d2
0 d1
0 d4
0 d3
Reduction in Cross-Section
Elastomers seal by their ability to be compressed therefore, if the ID of the O-ring is stretched, the
cross-section of the O-ring will decrease. The following table gives the O-ring cross-sections that
result of from various percentages of ID stretch.
ISO Sizing
Number
Original O-Ring C/S
Reduced O-Ring C/S at % ID Stretch (Inch/mm)
Inch
mm
1%
2%
3%
4%
5%
000
0.070
1.78
0.069/1.76
0.069/1.74
0.068/1.73
0.068/1.71
0.068/1.69
100
0.103
2.62
0.102/2.59
0.101/2.57
0.100/2.54
0.100/2.52
0.100/2.49
200
0.139
3.53
0.138/3.49
0.137/3.46
0.136/3.42
0.135/3.39
0.134/3.35
300
0.210
5.33
0.208/5.28
0.206/5.22
0.205/5.17
0.204/5.12
0.203/5.06
400
0.275
6.99
0.272/6.92
0.270/6.85
0.268/6.78
0.267/6.71
0.266/6.64
Compression
The difference between the original O-ring cross-section and the final O-ring cross-section once
installed is known as the compression squeeze.
Compression Squeeze
C/S
Compression Squeeze = C/S - H
This can usually be expressed as a percentage: O-Ring C/S Squeeze (%) = Compression Squeeze x 100

C/S
For recommended O-ring C/S squeeze (%) values please refer to page 5.
Gland Fill
The gland fill is the percentage of the gland that is occupied by the O-ring. It is calculated by dividing
the cross-sectional area (CSA) of the O-ring by the cross-sectional area of the gland.
Area of a circle = r2 and r = D , where D = diameter (C/S)

2
Therefore, O-ring CSA = C/S 2

2
( )
w
Gland Fill (%) = O-ring CSA x 100

Gland CSA
w- housing width
h- housing height
* Effect of gland angle not addressed.
It is important to consider the housing fill or occupancy of the installed O-ring to avoid detrimental
effects on radial sealing performance. Housing fill of the installed O-ring should not be more than
85 % to allow for possible O-ring thermal expansion, volume swell due to fluid exposure and effects
of tolerances.
Volume change is the increase or decrease of the volume of an elastomer after it has been in
contact with a fluid, measured in percent (%). For static O-ring applications volume swell up to
30 % can usually be tolerated. For dynamic applications, 10 or 15 % swell is a reasonable maximum
unless special provisions are made in the gland design itself. This is a general rule and there may
occasionally be exceptions.
Gland CSA = h x w*
It is also important to note there are significant differences in the coefficients of thermal expansion
and contraction between the O-ring material and the housing materials. Elastomers can have
coefficients of expansion 7 to 20 times higher than that of metal, such as steel.
OD
O-Ring Sizing Charts
ID
C/S
000 Series
O-ring Sizing Charts
ISO Sizing
Number
10
Nominal
ID
C/S
Inch Standard (Actual)

ID
C/S
Metric Standard (Actual)

ID
C/S
001
1/32
1/32
0.029
0.004
0.040
0.003
0.74
0.10
1.02
0.08
002
3/64
3/64
0.042
0.004
0.050
0.003
1.07
0.10
1.27
0.08
003
1/16
1/16
0.056
0.004
0.060
0.003
1.42
0.10
1.52
0.08
004
5/64
1/16
0.070
0.005
0.070
0.003
1.78
0.13
1.78
0.08
005
3/32
1/16
0.101
0.005
0.070
0.003
2.57
0.13
1.78
0.08
006
1/8
1/16
0.114
0.005
0.070
0.003
2.90
0.13
1.78
0.08
007
5/32
1/16
0.145
0.005
0.070
0.003
3.68
0.13
1.78
0.08
008
3/16
1/16
0.176
0.005
0.070
0.003
4.47
0.13
1.78
0.08
009
7/32
1/16
0.208
0.005
0.070
0.003
5.28
0.13
1.78
0.08
010
1/4
1/16
0.239
0.005
0.070
0.003
6.07
0.13
1.78
0.08
011
5/16
1/16
0.301
0.005
0.070
0.003
7.65
0.13
1.78
0.08
012
3/8
1/16
0.364
0.005
0.070
0.003
9.25
0.13
1.78
0.08
013
7/16
1/16
0.426
0.005
0.070
0.003
10.82
0.13
1.78
0.08
014
1/2
1/16
0.489
0.005
0.070
0.003
12.42
0.13
1.78
0.08
015
9/16
1/16
0.551
0.007
0.070
0.003
14.00
0.18
1.78
0.08
016
5/8
1/16
0.614
0.009
0.070
0.003
15.60
0.23
1.78
0.08
017
11/16
1/16
0.676
0.009
0.070
0.003
17.17
0.23
1.78
0.08
018
3/4
1/16
0.739
0.009
0.070
0.003
18.77
0.23
1.78
0.08
019
13/16
1/16
0.801
0.009
0.070
0.003
20.35
0.23
1.78
0.08
020
7/8
1/16
0.864
0.009
0.070
0.003
21.95
0.23
1.78
0.08
021
15/16
1/16
0.926
0.009
0.070
0.003
23.52
0.23
1.78
0.08
022
1/16
0.989
0.010
0.070
0.003
25.12
0.25
1.78
0.08
023
1-1/16
1/16
1.051
0.010
0.070
0.003
26.70
0.25
1.78
0.08
024
1-1/8
1/16
1.114
0.010
0.070
0.003
28.30
0.25
1.78
0.08
025
1-3/16
1/16
1.176
0.011
0.070
0.003
29.87
0.28
1.78
0.08
026
1-1/4
1/16
1.239
0.011
0.070
0.003
31.47
0.28
1.78
0.08
027
1-5/16
1/16
1.301
0.011
0.070
0.003
33.05
0.28
1.78
0.08
028
1-3/8
1/16
1.364
0.013
0.070
0.003
34.65
0.33
1.78
0.08
029
1-1/2
1/16
1.481
0.013
0.070
0.003
37.62
0.33
1.78
0.08
030
1-5/8
1/16
1.614
0.013
0.070
0.003
41.00
0.33
1.78
0.08
031
1-3/4
1/16
1.739
0.015
0.070
0.003
44.17
0.38
1.78
0.08
032
1-7/8
1/16
1.864
0.015
0.070
0.003
47.35
0.38
1.78
0.08
033
1/16
1.989
0.018
0.070
0.003
50.52
0.46
1.78
0.08
034
2-1/8
1/16
2.114
0.018
0.070
0.003
53.70
0.46
1.78
0.08
OD
ID
C/S
000 Series
Nominal
ID
C/S

ID
C/S

ID
C/S
035
2-1/4
1/16
2.239
0.018
0.070
0.003
56.87
0.46
1.78
0.08
036
2-3/8
1/16
2.364
0.018
0.070
0.003
60.05
0.46
1.78
0.08
037
2-1/2
1/16
2.489
0.018
0.070
0.003
63.22
0.46
1.78
0.08
038
2-5/8
1/16
2.614
0.020
0.070
0.003
66.40
0.51
1.78
0.08
039
2-3/4
1/16
2.739
0.020
0.070
0.003
69.57
0.51
1.78
0.08
040
2-7/8
1/16
2.864
0.020
0.070
0.003
72.75
0.51
1.78
0.08
041
1/16
2.989
0.024
0.070
0.003
75.92
0.61
1.78
0.08
042
3-1/4
1/16
3.239
0.024
0.070
0.003
82.27
0.61
1.78
0.08
043
3-1/2
1/16
3.489
0.024
0.070
0.003
88.62
0.61
1.78
0.08
044
3-3/4
1/16
3.739
0.027
0.070
0.003
94.97
0.69
1.78
0.08
045
1/16
3.989
0.027
0.070
0.003
101.32
0.69
1.78
0.08
046
4-1/4
1/16
4.239
0.030
0.070
0.003
107.67
0.76
1.78
0.08
047
4-1/2
1/16
4.489
0.030
0.070
0.003
114.02
0.76
1.78
0.08
048
4-3/4
1/16
4.739
0.030
0.070
0.003
120.37
0.76
1.78
0.08
049
1/16
4.989
0.037
0.070
0.003
126.72
0.94
1.78
0.08
050
5-1/4
1/16
5.239
0.037
0.070
0.003
133.07
0.94
1.78
0.08
ISO Sizing
Number
11
OD
ID
C/S
100 Series
ISO Sizing
Number
12
Nominal
ID
C/S

ID
C/S

ID
C/S
102
1/16
3/32
0.049
0.005
0.103
0.003
1.24
0.13
2.62
0.08
103
3/32
3/32
0.081
0.005
0.103
0.003
2.06
0.13
2.62
0.08
104
1/8
3/32
0.112
0.005
0.103
0.003
2.84
0.13
2.62
0.08
105
5/32
3/32
0.143
0.005
0.103
0.003
3.63
0.13
2.62
0.08
106
3/16
3/32
0.174
0.005
0.103
0.003
4.42
0.13
2.62
0.08
107
7/32
3/32
0.206
0.005
0.103
0.003
5.23
0.13
2.62
0.08
108
1/4
3/32
0.237
0.005
0.103
0.003
6.02
0.13
2.62
0.08
109
5/16
3/32
0.299
0.005
0.103
0.003
7.59
0.13
2.62
0.08
110
3/8
3/32
0.362
0.005
0.103
0.003
9.19
0.13
2.62
0.08
111
7/16
3/32
0.424
0.005
0.103
0.003
10.77
0.13
2.62
0.08
112
1/2
3/32
0.487
0.005
0.103
0.003
12.37
0.13
2.62
0.08
113
9/16
3/32
0.549
0.007
0.103
0.003
13.94
0.18
2.62
0.08
114
5/8
3/32
0.612
0.009
0.103
0.003
15.54
0.23
2.62
0.08
115
11/16
3/32
0.674
0.009
0.103
0.003
17.12
0.23
2.62
0.08
116
3/4
3/32
0.737
0.009
0.103
0.003
18.72
0.23
2.62
0.08
117
13/16
3/32
0.799
0.010
0.103
0.003
20.29
0.25
2.62
0.08
118
7/8
3/32
0.862
0.010
0.103
0.003
21.89
0.25
2.62
0.08
119
15/16
3/32
0.924
0.010
0.103
0.003
23.47
0.25
2.62
0.08
120
3/32
0.987
0.010
0.103
0.003
25.07
0.25
2.62
0.08
121
1-1/16
3/32
1.049
0.010
0.103
0.003
26.64
0.25
2.62
0.08
122
1-1/8
3/32
1.112
0.010
0.103
0.003
28.24
0.25
2.62
0.08
123
1-3/16
3/32
1.174
0.012
0.103
0.003
29.82
0.30
2.62
0.08
124
1-1/4
3/32
1.237
0.012
0.103
0.003
31.42
0.30
2.62
0.08
125
1-5/16
3/32
1.299
0.012
0.103
0.003
32.99
0.30
2.62
0.08
126
1-3/8
3/32
1.362
0.012
0.103
0.003
34.59
0.30
2.62
0.08
127
1-7/16
3/32
1.424
0.012
0.103
0.003
36.17
0.30
2.62
0.08
128
1-1/2
3/32
1.487
0.012
0.103
0.003
37.77
0.30
2.62
0.08
129
1-9/16
3/32
1.549
0.015
0.103
0.003
39.34
0.38
2.62
0.08
130
1-5/8
3/32
1.612
0.015
0.103
0.003
40.94
0.38
2.62
0.08
131
1-11/16
3/32
1.674
0.015
0.103
0.003
42.52
0.38
2.62
0.08
132
1-3/4
3/32
1.737
0.015
0.103
0.003
44.12
0.38
2.62
0.08
133
1-13/16
3/32
1.799
0.015
0.103
0.003
45.69
0.38
2.62
0.08
134
1-7/8
3/32
1.862
0.015
0.103
0.003
47.29
0.38
2.62
0.08
135
1-15/16
3/32
1.925
0.017
0.103
0.003
48.90
0.43
2.62
0.08
OD
ID
C/S
100 Series
Nominal
ID
C/S

ID
C/S

ID
C/S
136
3/32
1.987
0.017
0.103
0.003
50.47
0.43
2.62
0.08
137
2-1/16
3/32
2.050
0.017
0.103
0.003
52.07
0.43
2.62
0.08
138
2-1/8
3/32
2.112
0.017
0.103
0.003
53.64
0.43
2.62
0.08
139
2-3/16
3/32
2.175
0.017
0.103
0.003
55.25
0.43
2.62
0.08
140
2-1/4
3/32
2.237
0.017
0.103
0.003
56.82
0.43
2.62
0.08
141
2-5/16
3/32
2.300
0.020
0.103
0.003
58.42
0.51
2.62
0.08
142
2-3/8
3/32
2.362
0.020
0.103
0.003
59.99
0.51
2.62
0.08
143
2-7/16
3/32
2.425
0.020
0.103
0.003
61.60
0.51
2.62
0.08
144
2-1/2
3/32
2.487
0.020
0.103
0.003
63.17
0.51
2.62
0.08
145
2-9/16
3/32
2.550
0.020
0.103
0.003
64.77
0.51
2.62
0.08
146
2-5/8
3/32
2.612
0.020
0.103
0.003
66.34
0.51
2.62
0.08
147
2-11/16
3/32
2.675
0.022
0.103
0.003
67.95
0.56
2.62
0.08
148
2-3/4
3/32
2.737
0.022
0.103
0.003
69.52
0.56
2.62
0.08
149
2-13/16
3/32
2.800
0.022
0.103
0.003
71.12
0.56
2.62
0.08
150
2-7/8
3/32
2.862
0.022
0.103
0.003
72.69
0.56
2.62
0.08
151
3/32
2.987
0.024
0.103
0.003
75.87
0.61
2.62
0.08
152
3-1/4
3/32
3.237
0.024
0.103
0.003
82.22
0.61
2.62
0.08
153
3-1/2
3/32
3.487
0.024
0.103
0.003
88.57
0.61
2.62
0.08
154
3-3/4
3/32
3.737
0.028
0.103
0.003
94.92
0.71
2.62
0.08
155
3/32
3.987
0.028
0.103
0.003
101.27
0.71
2.62
0.08
156
4-1/4
3/32
4.237
0.030
0.103
0.003
107.62
0.76
2.62
0.08
157
4-1/2
3/32
4.487
0.030
0.103
0.003
113.97
0.76
2.62
0.08
158
4-3/4
3/32
4.737
0.030
0.103
0.003
120.32
0.76
2.62
0.08
159
3/32
4.987
0.035
0.103
0.003
126.67
0.89
2.62
0.08
160
5-1/4
3/32
5.237
0.035
0.103
0.003
133.02
0.89
2.62
0.08
161
5-1/2
3/32
5.487
0.035
0.103
0.003
139.37
0.89
2.62
0.08
162
5-3/4
3/32
5.737
0.035
0.103
0.003
145.72
0.89
2.62
0.08
163
3/32
5.987
0.035
0.103
0.003
152.07
0.89
2.62
0.08
164
6-1/4
3/32
6.237
0.040
0.103
0.003
158.42
1.02
2.62
0.08
165
6-1/2
3/32
6.487
0.040
0.103
0.003
164.77
1.02
2.62
0.08
166
6-3/4
3/32
6.737
0.040
0.103
0.003
171.12
1.02
2.62
0.08
167
3/32
6.987
0.040
0.103
0.003
177.47
1.02
2.62
0.08
168
7-1/4
3/32
7.237
0.045
0.103
0.003
183.82
1.14
2.62
0.08
169
7-1/2
3/32
7.487
0.045
0.103
0.003
190.17
1.14
2.62
0.08
ISO Sizing
Number
13
OD
ID
100 Series
ISO Sizing
Number
14
C/S
Nominal
ID
C/S

ID
C/S

ID
C/S
170
7-3/4
3/32
7.737
0.045
0.103
0.003
196.52
1.14
2.62
0.08
171
3/32
7.987
0.045
0.103
0.003
202.87
1.14
2.62
0.08
172
8-1/4
3/32
8.237
0.050
0.103
0.003
209.22
1.27
2.62
0.08
173
8-1/2
3/32
8.487
0.050
0.103
0.003
215.57
1.27
2.62
0.08
174
8-3/4
3/32
8.737
0.050
0.103
0.003
221.92
1.27
2.62
0.08
175
3/32
8.987
0.050
0.103
0.003
228.27
1.27
2.62
0.08
176
9-1/4
3/32
9.237
0.055
0.103
0.003
234.62
1.40
2.62
0.08
177
9-1/2
3/32
9.487
0.055
0.103
0.003
240.97
1.40
2.62
0.08
178
9-3/4
3/32
9.737
0.055
0.103
0.003
247.32
1.40
2.62
0.08
OD
ID
200 Series
Nominal
ID
C/S

ID
C/S

ID
C/S
201
3/16
1/8
0.171
0.005
0.139
0.004
4.34
0.13
3.53
0.10
202
1/4
1/8
0.234
0.005
0.139
0.004
5.94
0.13
3.53
0.10
203
5/16
1/8
0.296
0.005
0.139
0.004
7.52
0.13
3.53
0.10
204
3/8
1/8
0.359
0.005
0.139
0.004
9.12
0.13
3.53
0.10
205
7/16
1/8
0.421
0.005
0.139
0.004
10.69
0.13
3.53
0.10
206
1/2
1/8
0.484
0.005
0.139
0.004
12.29
0.13
3.53
0.10
207
9/16
1/8
0.546
0.007
0.139
0.004
13.87
0.18
3.53
0.10
208
5/8
1/8
0.609
0.009
0.139
0.004
15.47
0.23
3.53
0.10
209
11/16
1/8
0.671
0.009
0.139
0.004
17.04
0.23
3.53
0.10
210
3/4
1/8
0.734
0.010
0.139
0.004
18.64
0.25
3.53
0.10
211
13/16
1/8
0.796
0.010
0.139
0.004
20.22
0.25
3.53
0.10
212
7/8
1/8
0.859
0.010
0.139
0.004
21.82
0.25
3.53
0.10
213
15/16
1/8
0.921
0.010
0.139
0.004
23.39
0.25
3.53
0.10
214
1/8
0.984
0.010
0.139
0.004
24.99
0.25
3.53
0.10
215
1-1/16
1/8
1.046
0.010
0.139
0.004
26.57
0.25
3.53
0.10
216
1-1/8
1/8
1.109
0.012
0.139
0.004
28.17
0.30
3.53
0.10
217
1-3/16
1/8
1.171
0.012
0.139
0.004
29.74
0.30
3.53
0.10
218
1-1/4
1/8
1.234
0.012
0.139
0.004
31.34
0.30
3.53
0.10
219
1-5/16
1/8
1.296
0.012
0.139
0.004
32.92
0.30
3.53
0.10
220
1-3/8
1/8
1.359
0.012
0.139
0.004
34.52
0.30
3.53
0.10
221
1-7/16
1/8
1.421
0.012
0.139
0.004
36.09
0.30
3.53
0.10
222
1-1/2
1/8
1.484
0.015
0.139
0.004
37.69
0.38
3.53
0.10
223
1-5/8
1/8
1.609
0.015
0.139
0.004
40.87
0.38
3.53
0.10
224
1-3/4
1/8
1.734
0.015
0.139
0.004
44.04
0.38
3.53
0.10
225
1-7/8
1/8
1.859
0.018
0.139
0.004
47.22
0.46
3.53
0.10
226
1/8
1.984
0.018
0.139
0.004
50.39
0.46
3.53
0.10
227
2-1/8
1/8
2.109
0.018
0.139
0.004
53.57
0.46
3.53
0.10
228
2-1/4
1/8
2.234
0.020
0.139
0.004
56.74
0.51
3.53
0.10
229
2-3/8
1/8
2.359
0.020
0.139
0.004
59.92
0.51
3.53
0.10
230
2-1/2
1/8
2.484
0.020
0.139
0.004
63.09
0.51
3.53
0.10
231
2-5/8
1/8
2.609
0.020
0.139
0.004
66.27
0.51
3.53
0.10
232
2-3/4
1/8
2.734
0.024
0.139
0.004
69.44
0.61
3.53
0.10
233
2-7/8
1/8
2.859
0.024
0.139
0.004
72.62
0.61
3.53
0.10
234
1/8
2.984
0.024
0.139
0.004
75.79
0.61
3.53
0.10
ISO Sizing
Number
C/S
15
OD
ID
200 Series
ISO Sizing
Number
16
C/S
Nominal
ID
C/S

ID
C/S

ID
C/S
235
3-1/8
1/8
3.109
0.024
0.139
0.004
78.97
0.61
3.53
0.10
236
3-1/4
1/8
3.234
0.024
0.139
0.004
82.14
0.61
3.53
0.10
237
3-3/8
1/8
3.359
0.024
0.139
0.004
85.32
0.61
3.53
0.10
238
3-1/2
1/8
3.484
0.024
0.139
0.004
88.49
0.61
3.53
0.10
239
3-5/8
1/8
3.609
0.028
0.139
0.004
91.67
0.71
3.53
0.10
240
3-3/4
1/8
3.734
0.028
0.139
0.004
94.84
0.71
3.53
0.10
241
3-7/8
1/8
3.859
0.028
0.139
0.004
98.02
0.71
3.53
0.10
242
1/8
3.984
0.028
0.139
0.004
101.19
0.71
3.53
0.10
243
4-1/8
1/8
4.109
0.028
0.139
0.004
104.37
0.71
3.53
0.10
244
4-1/4
1/8
4.234
0.030
0.139
0.004
107.54
0.76
3.53
0.10
245
4-3/8
1/8
4.359
0.030
0.139
0.004
110.72
0.76
3.53
0.10
246
4-1/2
1/8
4.484
0.030
0.139
0.004
113.89
0.76
3.53
0.10
247
4-5/8
1/8
4.609
0.030
0.139
0.004
117.07
0.76
3.53
0.10
248
4-3/4
1/8
4.734
0.030
0.139
0.004
120.24
0.76
3.53
0.10
249
4-7/8
1/8
4.859
0.035
0.139
0.004
123.42
0.89
3.53
0.10
250
1/8
4.984
0.035
0.139
0.004
126.59
0.89
3.53
0.10
251
5-1/8
1/8
5.109
0.035
0.139
0.004
129.77
0.89
3.53
0.10
252
5-1/4
1/8
5.234
0.035
0.139
0.004
132.94
0.89
3.53
0.10
253
5-3/8
1/8
5.359
0.035
0.139
0.004
136.12
0.89
3.53
0.10
254
5-1/2
1/8
5.484
0.035
0.139
0.004
139.29
0.89
3.53
0.10
255
5-5/8
1/8
5.609
0.035
0.139
0.004
142.47
0.89
3.53
0.10
256
5-3/4
1/8
5.734
0.035
0.139
0.004
145.64
0.89
3.53
0.10
257
5-7/8
1/8
5.859
0.035
0.139
0.004
148.82
0.89
3.53
0.10
258
1/8
5.984
0.035
0.139
0.004
151.99
0.89
3.53
0.10
259
6-1/4
1/8
6.234
0.040
0.139
0.004
158.34
1.02
3.53
0.10
260
6-1/2
1/8
6.484
0.040
0.139
0.004
164.69
1.02
3.53
0.10
261
6-3/4
1/8
6.734
0.040
0.139
0.004
171.04
1.02
3.53
0.10
262
1/8
6.984
0.040
0.139
0.004
177.39
1.02
3.53
0.10
263
7-1/4
1/8
7.234
0.045
0.139
0.004
183.74
1.14
3.53
0.10
264
7-1/2
1/8
7.484
0.045
0.139
0.004
190.09
1.14
3.53
0.10
265
7-3/4
1/8
7.734
0.045
0.139
0.004
196.44
1.14
3.53
0.10
266
1/8
7.984
0.045
0.139
0.004
202.79
1.14
3.53
0.10
267
8-1/4
1/8
8.234
0.050
0.139
0.004
209.14
1.27
3.53
0.10
268
8-1/2
1/8
8.484
0.050
0.139
0.004
215.49
1.27
3.53
0.10
OD
ID
200 Series
Nominal
ID
C/S

ID
C/S

ID
C/S
269
8-3/4
1/8
8.734
0.050
0.139
0.004
221.84
1.27
3.53
0.10
270
1/8
8.984
0.050
0.139
0.004
228.19
1.27
3.53
0.10
271
9-1/4
1/8
9.234
0.055
0.139
0.004
234.54
1.40
3.53
0.10
272
9-1/2
1/8
9.484
0.055
0.139
0.004
240.89
1.40
3.53
0.10
273
9--3/4
1/8
9.734
0.055
0.139
0.004
247.24
1.40
3.53
0.10
274
10
1/8
9.984
0.055
0.139
0.004
253.59
1.40
3.53
0.10
275
10-1/2
1/8
10.484
0.055
0.139
0.004
266.29
1.40
3.53
0.10
276
11
1/8
10.984
0.065
0.139
0.004
278.99
1.65
3.53
0.10
277
11-1/2
1/8
11.484
0.065
0.139
0.004
291.69
1.65
3.53
0.10
278
12
1/8
11.984
0.065
0.139
0.004
304.39
1.65
3.53
0.10
279
13
1/8
12.984
0.065
0.139
0.004
329.79
1.65
3.53
0.10
280
14
1/8
13.984
0.065
0.139
0.004
355.19
1.65
3.53
0.10
281
15
1/8
14.984
0.065
0.139
0.004
380.59
1.65
3.53
0.10
282
16
1/8
15.955
0.075
0.139
0.004
405.26
1.91
3.53
0.10
283
17
1/8
16.956
0.080
0.139
0.004
430.68
2.03
3.53
0.10
284
18
1/8
17.955
0.085
0.139
0.004
456.06
2.16
3.53
0.10
ISO Sizing
Number
C/S
17
OD
ID
300 Series
ISO Sizing
Number
18
C/S
Nominal
ID
C/S

ID
C/S

ID
C/S
309
7/16
3/16
0.412
0.005
0.210
0.005
10.46
0.13
5.33
0.13
310
1/2
3/16
0.475
0.005
0.210
0.005
12.07
0.13
5.33
0.13
311
9/16
3/16
0.537
0.007
0.210
0.005
13.64
0.18
5.33
0.13
312
5/8
3/16
0.600
0.009
0.210
0.005
15.24
0.23
5.33
0.13
313
11/16
3/16
0.662
0.009
0.210
0.005
16.81
0.23
5.33
0.13
314
3/4
3/16
0.725
0.010
0.210
0.005
18.42
0.25
5.33
0.13
315
13/16
3/16
0.787
0.010
0.210
0.005
19.99
0.25
5.33
0.13
316
7/8
3/16
0.850
0.010
0.210
0.005
21.59
0.25
5.33
0.13
317
15/16
3/16
0.912
0.010
0.210
0.005
23.16
0.25
5.33
0.13
318
3/16
0.975
0.010
0.210
0.005
24.77
0.25
5.33
0.13
319
1-1/16
3/16
1.037
0.010
0.210
0.005
26.34
0.25
5.33
0.13
320
1-1/8
3/16
1.100
0.012
0.210
0.005
27.94
0.30
5.33
0.13
321
1-3/16
3/16
1.162
0.012
0.210
0.005
29.51
0.30
5.33
0.13
322
1-1/4
3/16
1.225
0.012
0.210
0.005
31.12
0.30
5.33
0.13
323
1-5/16
3/16
1.287
0.012
0.210
0.005
32.69
0.30
5.33
0.13
324
1-3/8
3/16
1.350
0.012
0.210
0.005
34.29
0.30
5.33
0.13
325
1-1/2
3/16
1.475
0.015
0.210
0.005
37.47
0.38
5.33
0.13
326
1-5/8
3/16
1.600
0.015
0.210
0.005
40.64
0.38
5.33
0.13
327
1-3/4
3/16
1.725
0.015
0.210
0.005
43.82
0.38
5.33
0.13
328
1-7/8
3/16
1.850
0.015
0.210
0.005
46.99
0.38
5.33
0.13
329
3/16
1.975
0.018
0.210
0.005
50.17
0.46
5.33
0.13
330
2-1/8
3/16
2.100
0.018
0.210
0.005
53.34
0.46
5.33
0.13
331
2-1/4
3/16
2.225
0.018
0.210
0.005
56.52
0.46
5.33
0.13
332
2-3/8
3/16
2.350
0.018
0.210
0.005
59.69
0.46
5.33
0.13
333
2-1/2
3/16
2.475
0.020
0.210
0.005
62.87
0.51
5.33
0.13
334
2-5/8
3/16
2.600
0.020
0.210
0.005
66.04
0.51
5.33
0.13
335
2-3/4
3/16
2.725
0.020
0.210
0.005
69.22
0.51
5.33
0.13
336
2-7/8
3/16
2.850
0.020
0.210
0.005
72.39
0.51
5.33
0.13
337
3/16
2.975
0.024
0.210
0.005
75.57
0.61
5.33
0.13
338
3-1/8
3/16
3.100
0.024
0.210
0.005
78.74
0.61
5.33
0.13
339
3-1/4
3/16
3.225
0.024
0.210
0.005
81.92
0.61
5.33
0.13
340
3-3/8
3/16
3.350
0.024
0.210
0.005
85.09
0.61
5.33
0.13
341
3-1/2
3/16
3.475
0.024
0.210
0.005
88.27
0.61
5.33
0.13
342
3-5/8
3/16
3.600
0.028
0.210
0.005
91.44
0.71
5.33
0.13
OD
ID
300 Series
Nominal
ID
C/S

ID
C/S

ID
C/S
343
3-3/4
3/16
3.725
0.028
0.210
0.005
94.62
0.71
5.33
0.13
344
3-7/8
3/16
3.850
0.028
0.210
0.005
97.79
0.71
5.33
0.13
345
3/16
3.975
0.028
0.210
0.005
100.97
0.71
5.33
0.13
346
4-1/8
3/16
4.100
0.028
0.210
0.005
104.14
0.71
5.33
0.13
347
4-1/4
3/16
4.225
0.030
0.210
0.005
107.32
0.76
5.33
0.13
348
4-3/8
3/16
4.350
0.030
0.210
0.005
110.49
0.76
5.33
0.13
349
4-1/2
3/16
4.475
0.030
0.210
0.005
113.67
0.76
5.33
0.13
350
4-5/8
3/16
4.600
0.030
0.210
0.005
116.84
0.76
5.33
0.13
351
4-3/4
3/16
4.725
0.030
0.210
0.005
120.02
0.76
5.33
0.13
352
4-7/8
3/16
4.850
0.030
0.210
0.005
123.19
0.76
5.33
0.13
353
3/16
4.975
0.037
0.210
0.005
126.37
0.94
5.33
0.13
354
5-1/8
3/16
5.100
0.037
0.210
0.005
129.54
0.94
5.33
0.13
355
5-1/4
3/16
5.225
0.037
0.210
0.005
132.72
0.94
5.33
0.13
356
5-3/8
3/16
5.350
0.037
0.210
0.005
135.89
0.94
5.33
0.13
357
5-1/2
3/16
5.475
0.037
0.210
0.005
139.07
0.94
5.33
0.13
358
5-5/8
3/16
5.600
0.037
0.210
0.005
142.24
0.94
5.33
0.13
359
5-3/4
3/16
5.725
0.037
0.210
0.005
145.42
0.94
5.33
0.13
360
5-7/8
3/16
5.850
0.037
0.210
0.005
148.59
0.94
5.33
0.13
361
3/16
5.975
0.037
0.210
0.005
151.77
0.94
5.33
0.13
362
6-1/4
3/16
6.225
0.040
0.210
0.005
158.12
1.02
5.33
0.13
363
6-1/2
3/16
6.475
0.040
0.210
0.005
164.47
1.02
5.33
0.13
364
6-3/4
3/16
6.725
0.040
0.210
0.005
170.82
1.02
5.33
0.13
365
3/16
6.975
0.040
0.210
0.005
177.17
1.02
5.33
0.13
366
7-1/4
3/16
7.225
0.045
0.210
0.005
183.52
1.14
5.33
0.13
367
7-1/2
3/16
7.475
0.045
0.210
0.005
189.87
1.14
5.33
0.13
368
7-3/4
3/16
7.725
0.045
0.210
0.005
196.22
1.14
5.33
0.13
369
3/16
7.975
0.045
0.210
0.005
202.57
1.14
5.33
0.13
370
8-1/4
3/16
8.225
0.050
0.210
0.005
208.92
1.27
5.33
0.13
371
8-1/2
3/16
8.475
0.050
0.210
0.005
215.27
1.27
5.33
0.13
372
8-3/4
3/16
8.725
0.050
0.210
0.005
221.62
1.27
5.33
0.13
373
3/16
8.975
0.050
0.210
0.005
227.97
1.27
5.33
0.13
374
9-1/4
3/16
9.225
0.055
0.210
0.005
234.32
1.40
5.33
0.13
375
9-1/2
3/16
9.475
0.055
0.210
0.005
240.67
1.40
5.33
0.13
376
9-3/4
3/16
9.725
0.055
0.210
0.005
247.02
1.40
5.33
0.13
ISO Sizing
Number
C/S
19
OD
ID
300 Series
ISO Sizing
Number
20
C/S
Nominal
ID
C/S

ID
C/S

ID
C/S
377
10
3/16
9.975
0.055
0.210
0.005
253.37
1.40
5.33
0.13
378
10-1/2
3/16
10.475
0.060
0.210
0.005
266.07
1.52
5.33
0.13
379
11
3/16
10.975
0.060
0.210
0.005
278.77
1.52
5.33
0.13
380
11-1/2
3/16
11.475
0.065
0.210
0.005
291.47
1.65
5.33
0.13
381
12
3/16
11.975
0.065
0.210
0.005
304.17
1.65
5.33
0.13
382
13
3/16
12.975
0.065
0.210
0.005
329.57
1.65
5.33
0.13
383
14
3/16
13.975
0.070
0.210
0.005
354.97
1.78
5.33
0.13
384
15
3/16
14.975
0.070
0.210
0.005
380.37
1.78
5.33
0.13
385
16
3/16
15.955
0.075
0.210
0.005
405.26
1.91
5.33
0.13
386
17
3/16
16.955
0.080
0.210
0.005
430.66
2.03
5.33
0.13
387
18
3/16
17.955
0.085
0.210
0.005
456.06
2.16
5.33
0.13
388
19
3/16
18.952
0.090
0.210
0.005
481.38
2.29
5.33
0.13
389
20
3/16
19.952
0.095
0.210
0.005
506.78
2.41
5.33
0.13
390
21
3/16
20.952
0.095
0.210
0.005
532.18
2.41
5.33
0.13
391
22
3/16
21.952
0.100
0.210
0.005
557.58
2.54
5.33
0.13
392
23
3/16
22.940
0.105
0.210
0.005
582.68
2.67
5.33
0.13
393
24
3/16
23.940
0.110
0.210
0.005
608.08
2.79
5.33
0.13
394
25
3/16
24.940
0.115
0.210
0.005
633.48
2.92
5.33
0.13
395
26
3/16
25.940
0.120
0.210
0.005
658.88
3.05
5.33
0.13
OD
ID
C/S
400 Series*
Nominal
ID
C/S

ID
C/S

ID
C/S
425
4-1/2
1/4
4.475
0.033
0.275
0.006
113.67
0.84
6.99
0.15
426
4-5/8
1/4
4.600
0.033
0.275
0.006
116.84
0.84
6.99
0.15
427
4-3/4
1/4
4.725
0.033
0.275
0.006
120.02
0.84
6.99
0.15
428
4-7/8
1/4
4.850
0.033
0.275
0.006
123.19
0.84
6.99
0.15
429
1/4
4.975
0.037
0.275
0.006
126.37
0.94
6.99
0.15
430
5-1/8
1/4
5.100
0.037
0.275
0.006
129.54
0.94
6.99
0.15
431
5-1/4
1/4
5.225
0.037
0.275
0.006
132.72
0.94
6.99
0.15
432
5-3/8
1/4
5.350
0.037
0.275
0.006
135.89
0.94
6.99
0.15
433
5-1/2
1/4
5.475
0.037
0.275
0.006
139.07
0.94
6.99
0.15
434
5-5/8
1/4
5.600
0.037
0.275
0.006
142.24
0.94
6.99
0.15
435
5-3/4
1/4
5.725
0.037
0.275
0.006
145.42
0.94
6.99
0.15
436
5-7/8
1/4
5.850
0.037
0.275
0.006
148.59
0.94
6.99
0.15
437
1/4
5.975
0.037
0.275
0.006
151.77
0.94
6.99
0.15
438
6-1/4
1/4
6.225
0.040
0.275
0.006
158.12
1.02
6.99
0.15
439
6-1/2
1/4
6.475
0.040
0.275
0.006
164.47
1.02
6.99
0.15
440
6-3/4
1/4
6.725
0.040
0.275
0.006
170.82
1.02
6.99
0.15
441
1/4
6.975
0.040
0.275
0.006
177.17
1.02
6.99
0.15
442
7-1/4
1/4
7.225
0.045
0.275
0.006
183.52
1.14
6.99
0.15
443
7-1/2
1/4
7.475
0.045
0.275
0.006
189.87
1.14
6.99
0.15
444
7-3/4
1/4
7.725
0.045
0.275
0.006
196.22
1.14
6.99
0.15
445
1/4
7.975
0.045
0.275
0.006
202.57
1.14
6.99
0.15
446
8-1/2
1/4
8.475
0.055
0.275
0.006
215.27
1.40
6.99
0.15
447
1/4
8.975
0.055
0.275
0.006
227.97
1.40
6.99
0.15
448
9-1/2
1/4
9.475
0.055
0.275
0.006
240.67
1.40
6.99
0.15
449
10
1/4
9.975
0.055
0.275
0.006
253.37
1.40
6.99
0.15
450
10-1/2
1/4
10.475
0.060
0.275
0.006
266.07
1.52
6.99
0.15
451
11
1/4
10.975
0.060
0.275
0.006
278.77
1.52
6.99
0.15
452
11-1/2
1/4
11.475
0.060
0.275
0.006
291.47
1.52
6.99
0.15
453
12
1/4
11.975
0.060
0.275
0.006
304.17
1.52
6.99
0.15
454
12-1/2
1/4
12.475
0.060
0.275
0.006
316.87
1.52
6.99
0.15
455
13
1/4
12.975
0.060
0.275
0.006
329.57
1.52
6.99
0.15
456
13-1/2
1/4
13.475
0.070
0.275
0.006
342.27
1.78
6.99
0.15
457
14
1/4
13.975
0.070
0.275
0.006
354.97
1.78
6.99
0.15
ISO Sizing
Number
21
OD
ID
400 Series
ISO Sizing
Number
C/S
Nominal
ID
C/S

ID
C/S

ID
C/S
458
14-1/2
1/4
14.475
0.070
0.275
0.006
367.67
1.78
6.99
0.15
459
15
1/4
14.975
0.070
0.275
0.006
380.37
1.78
6.99
0.15
460
15-1/2
1/4
15.475
0.070
0.275
0.006
393.07
1.78
6.99
0.15
461
16
1/4
15.955
0.075
0.275
0.006
405.26
1.91
6.99
0.15
462
16-1/2
1/4
16.455
0.075
0.275
0.006
417.96
1.91
6.99
0.15
463
17
1/4
16.955
0.080
0.275
0.006
430.66
2.03
6.99
0.15
464
17-1/2
1/4
17.455
0.085
0.275
0.006
443.36
2.16
6.99
0.15
465
18
1/4
17.955
0.085
0.275
0.006
456.06
2.16
6.99
0.15
466
18-1/2
1/4
18.455
0.085
0.275
0.006
468.76
2.16
6.99
0.15
467
19
1/4
18.955
0.090
0.275
0.006
481.46
2.29
6.99
0.15
468
19-1/2
1/4
19.455
0.090
0.275
0.006
494.16
2.29
6.99
0.15
469
20
1/4
19.955
0.095
0.275
0.006
506.86
2.41
6.99
0.15
470
21
1/4
20.955
0.095
0.275
0.006
532.26
2.41
6.99
0.15
471
22
1/4
21.955
0.100
0.275
0.006
557.66
2.54
6.99
0.15
472
23
1/4
22.940
0.105
0.275
0.006
582.68
2.67
6.99
0.15
473
24
1/4
23.940
0.110
0.275
0.006
608.08
2.79
6.99
0.15
474
25
1/4
24.940
0.115
0.275
0.006
633.48
2.92
6.99
0.15
475
26
1/4
25.940
0.120
0.275
0.006
658.88
3.05
6.99
0.15
* Hi-Tech Seals Inc. offers O-rings in sizes ranging from 400-425. These O-ring size dimensions and tolerances are
unassigned under ISO 3601. In addition, Hi-Tech Seals stocks specific non-standard cross-section O-rings such as
3/8", 1/2" and 3/4".
22
OD
O-Rings for Tube

Fittings
ID
C/S
Sizing
Number
CS
ID
901
0.185
0.005
0.056
0.003
4.70
0.13
1.42
0.08
902
0.239
0.005
0.064
0.003
6.07
0.13
1.63
0.08
903
0.301
0.005
0.064
0.003
7.65
0.13
1.63
0.08
904
0.351
0.005
0.072
0.003
8.92
0.13
1.83
0.08
905
0.414
0.005
0.072
0.003
10.52
0.13
1.83
0.08
906
0.468
0.005
0.078
0.003
11.89
0.13
1.98
0.08
907
0.530
0.005
0.082
0.003
13.46
0.13
2.08
0.08
908
0.644
0.009
0.087
0.003
16.36
0.23
2.21
0.08
909
0.706
0.009
0.097
0.003
17.93
0.23
2.46
0.08
910
0.755
0.009
0.097
0.003
19.18
0.23
2.46
0.08
911
0.863
0.009
0.116
0.004
21.92
0.23
2.95
0.10
912
0.924
0.009
0.116
0.004
23.47
0.23
2.95
0.10
913
0.986
0.010
0.116
0.004
25.04
0.25
2.95
0.10
914
1.048
0.010
0.116
0.004
26.62
0.25
2.95
0.10
916
1.171
0.010
0.116
0.004
29.74
0.25
2.95
0.10
918
1.355
0.012
0.116
0.004
34.42
0.30
2.95
0.10
920
1.475
0.014
0.118
0.004
37.47
0.36
3.00
0.10
924
1.720
0.014
0.118
0.004
43.69
0.36
3.00
0.10
928
2.090
0.018
0.118
0.004
53.09
0.36
3.00
0.10
932
2.337
0.018
0.118
0.004
59.36
0.36
3.00
0.10

ID
CS
ORB Series
23
Tolerances for Non-Standard O-Rings

Cross-section tolerances for non-standard O-rings
Cross-section
Inch
Tolerance
Inch
Cross-section
mm
Tolerance
mm
0.031 < d2 0.124
0.003
0.80 < d2 3.15
0.08
0.124 < d2 0.177
0.004
3.15 < d2 4.50
0.10
0.177 < d2 0.248
0.005
4.50 < d2 6.30
0.13
0.248 < d2 0.331
0.006
6.30 < d2 8.40
0.15
Tolerances for Non-Standard O-rings
Inside diameter tolerances for non-standard O-rings
24
Inside diameter (d1)

Inch
Tolerance
Inch
Inside diameter (d1)

mm
Tolerance
mm
0.027 to 0.060
0.004
0.68 to 1.53
0.10
0.061 to 0.460
0.005
1.54 to 11.69
0.13
0.461 to 0.530
0.006
11.70 to 13.46
0.15
0.531 to 0.690
0.007
13.47 to 17.53
0.18
0.691 to 0.810
0.008
17.54 to 20.57
0.20
0.811 to 0.940
0.009
20.58 to 23.88
0.23
0.941 to 1.130
0.010
23.89 to 28.70
0.25
1.131 to 1.400
0.012
28.71 to 35.56
0.30
1.401 to 1.700
0.014
35.57 to 43.18
0.36
1.701 to 2.000
0.016
43.19 to 50.80
0.41
2.001 to 2.300
0.018
50.81 to 58.42
0.46
2.301 to 2.620
0.020
58.43 to 66.55
0.51
2.621 to 2.950
0.022
66.56 to 74.93
0.56
2.951 to 3.290
0.024
74.94 to 83.57
0.61
3.291 to 3.630
0.026
83.58 to 92.20
0.66
3.631 to 4.000
0.028
92.21 to 101.60
0.71
4.001 to 4.620
0.030
101.61 to 117.35
0.76
4.621 to 5.560
0.035
117.36 to 141.22
0.89
5.561 to 6.550
0.040
141.23 to 166.37
1.02
6.551 to 7.560
0.045
166.38 to 192.02
1.14
7.561 to 8.610
0.050
192.03 to 218.69
1.27
8.611 to 9.975
0.055
218.70 to 253.37
1.40
9.976 to 11.400
0.060
253.38 to 289.56
1.52
11.401 to 13.700
0.070
289.57 to 347.98
1.78
13.701 to 16.100
0.080
347.99 to 408.94
2.03
16.101 to 18.600
0.090
408.95 to 472.44
2.29
18.601 to 22.500
0.100
472.45 to 571.50
2.54
22.501 to 28.000
0.120
571.51 to 711.20
3.05
28.001 to 33.700
0.140
711.21 to 855.98
3.56
33.701 to 39.600
0.160
855.99 to 1005.84
4.06
39.601 to 45.800
0.180
1005.85 to 1163.32
4.57
45.801 to 52.000
0.200
1163.33 to 1320.80
5.08

Face Seal Glands
Metric Sizes
C/S
Gland Depth
0.13
Liquid ( +- 0.00
)
Vacuum/Gases ( 0.13)
0.90
0.68
0.02
1.30
1.10
1.00 - 1.02
0.75
0.02
1.45
1.20
1.20
0.90
0.02
1.75
1.45
1.25 - 1.27
0.94
0.02
1.80
1.50
1.42
1.07
0.02
2.05
1.70
1.50
1.13
0.02
2.20
1.80
1.60 - 1.63
1.20
0.03
2.35
1.90
1.78 - 1.80
1.34
0.03
2.60
2.15
1.90
1.43
0.03
2.75
2.30
2.00
1.51
0.04
2.90
2.40
2.20 - 2.21
1.67
0.04
2.90
2.55
2.40
1.82
0.04
3.20
2.80
2.46
1.87
0.04
3.25
2.85
2.50
1.90
0.04
3.30
2.90
2.62
1.99
0.04
3.50
3.05
2.70
2.05
0.04
3.60
3.15
2.95
2.24
0.04
3.90
3.40
3.00
2.27
0.04
3.90
3.45
3.15
2.38
0.05
4.15
3.60
3.50 - 3.53
2.67
0.05
4.60
4.05
3.60
2.72
0.05
4.70
4.10
4.00
3.03
0.06
5.25
4.60
4.50
3.60
0.06
6.10
5.10
4.70
3.76
0.06
6.40
5.35
4.80
3.84
0.06
6.50
5.45
5.00
4.00
0.06
6.80
5.70
5.33- 5.34
4.26
0.08
7.25
6.05
5.50
4.40
0.08
7.45
6.25
5.70
4.56
0.08
7.75
6.50
5.80
4.64
0.08
7.90
6.60
6.00
4.98
0.08
8.00
6.75
6.40
5.31
0.10
8.30
7.20
6.50
5.40
0.10
8.40
7.30
6.90
5.73
0.10
8.95
7.75
6.99
5.80
0.10
9.05
7.85
7.00
5.81
0.10
9.05
7.90
7.50
6.23
0.10
9.70
8.40
8.00
6.64
0.10
10.35
9.00
8.40
6.97
0.15
10.90
9.45
Groove Width
This chart is based on DIN. 3771 information.
25
Dynamic Reciprocating Applications
Metric Sizes
C/S
Gland Depth
Diametral
Clearance
0.90
0.72
0.02
0.10
1.20
0.05
1.00 - 1.02
0.80
0.02
0.10
1.35
0.05
0.13
( +- 0.00
)
Max.
Eccentricity
1.20
0.96
0.02
0.10
1.60
0.05
1.25 - 1.27
1.00
0.02
0.10
1.70
0.05
1.42
1.13
0.02
0.10
1.90
0.05
1.50
1.20
0.02
0.10
2.00
0.05
1.60 - 1.63
1.28
0.03
0.10
2.10
0.05
1.78 - 1.80
1.42
0.03
0.10
2.40
0.05
1.90
1.52
0.03
0.10
2.50
0.05
2.00
1.60
0.04
0.10
2.65
0.05
2.20 - 2.21
1.89
0.04
0.10
3.00
0.05
2.40
2.06
0.04
0.10
3.25
0.05
2.46
2.11
0.04
0.10
3.35
0.05
2.50
2.15
0.04
0.10
3.40
0.05
2.62
2.25
0.04
0.10
3.55
0.05
2.70
2.32
0.04
0.10
3.70
0.05
2.95
2.53
0.04
0.10
4.00
0.05
3.00
2.61
0.04
0.15
4.05
0.07
3.15
2.74
0.05
0.15
4.25
0.07
3.50 - 3.53
3.07
0.05
0.15
4.75
0.07
3.60
3.13
0.05
0.15
4.85
0.07
4.00
3.48
0.05
0.15
5.40
0.07
4.50
3.99
0.05
0.15
6.00
0.07
4.70
4.17
0.05
0.15
6.30
0.07
4.80
4.26
0.05
0.15
6.40
0.07
5.00
4.44
0.05
0.15
6.70
0.10
5.33- 5.34
4.73
0.05
0.15
7.15
0.10
5.50
4.88
0.05
0.15
7.40
0.10
5.70
5.06
0.05
0.15
7.60
0.10
5.80
5.15
0.05
0.15
7.75
0.10
6.00
5.19
0.05
0.18
8.15
0.13
6.40
5.54
0.05
0.18
8.70
0.13
6.50
5.63
0.05
0.18
8.85
0.13
6.90
5.97
0.05
0.18
9.40
0.13
6.99
6.05
0.05
0.18
9.50
0.13
7.00
6.06
0.05
0.18
9.55
0.13
7.50
6.49
0.05
0.18
10.20
0.13
8.00
6.92
0.05
0.18
10.90
0.13
8.40
7.27
0.05
0.18
11.45
0.13
26
Groove Width
Static Radial Applications

Metric Sizes
Gland Depth
Diametral
Clearance
0.90
0.65
0.02
0.10
1.20
0.05
1.00 - 1.02
0.72
0.02
0.10
1.35
0.05
Groove Width
0.13
( +- 0.00
)
Max.
Eccentricity
1.20
0.87
0.02
0.10
1.60
0.05
1.25 - 1.27
0.91
0.02
0.10
1.65
0.05
1.42
1.03
0.02
0.10
1.90
0.05
1.50
1.09
0.02
0.10
2.00
0.05
1.60 - 1.63
1.16
0.03
0.10
2.10
0.05
1.78 - 1.80
1.29
0.03
0.10
2.35
0.05
1.90
1.38
0.03
0.10
2.50
0.05
2.00
1.45
0.04
0.10
2.65
0.05
2.20 - 2.21
1.74
0.04
0.10
3.00
0.05
2.40
1.90
0.04
0.10
3.25
0.05
2.46
1.94
0.04
0.10
3.35
0.05
2.50
1.98
0.04
0.10
3.40
0.05
2.62
2.07
0.04
0.10
3.55
0.05
2.70
2.13
0.04
0.10
3.65
0.05
2.95
2.33
0.04
0.10
4.00
0.05
3.00
2.40
0.04
0.15
4.05
0.07
3.15
2.52
0.05
0.15
4.25
0.07
3.50 - 3.53
2.82
0.05
0.15
4.75
0.07
3.60
2.88
0.05
0.15
4.85
0.07
4.00
3.20
0.06
0.15
5.40
0.07
4.50
3.64
0.06
0.15
6.00
0.07
4.70
3.80
0.06
0.15
6.30
0.07
4.80
3.88
0.06
0.15
6.40
0.07
5.00
4.04
0.06
0.15
6.70
0.10
5.33- 5.34
4.31
0.08
0.15
7.15
0.10
5.50
4.45
0.08
0.15
7.35
0.10
5.70
4.61
0.08
0.15
7.65
0.10
5.80
4.69
0.08
0.15
7.75
0.10
6.00
4.91
0.08
0.18
8.15
0.13
6.40
5.24
0.10
0.18
8.70
0.13
6.50
5.32
0.10
0.18
8.85
0.13
6.90
5.65
0.10
0.18
9.40
0.13
6.99
5.72
0.10
0.18
9.50
0.13
7.00
5.73
0.10
0.18
9.55
0.13
7.50
6.14
0.10
0.18
10.20
0.13
8.00
6.55
0.10
0.18
10.90
0.13
8.40
6.87
0.15
0.18
11.45
0.13
C/S
27
Common O-Ring Failures

Extrusion (and/or Nibbling) Description: The seal develops ragged edges (generally
on the low-pressure side) which appear tattered.
Contributing Factors: Excessive clearances. Excessive

pressure. Low-modulus/hardness elastomer. Excessive
gland fill. Irregular clearance gaps. Sharp gland edges.
Improper sizing.
O-Ring Failures
Suggested Solutions: Decrease clearances. Highermodulus/hardness elastomer. Proper gland design. Use of
polymer backup rings.
Over-Compression
Description: The seal exhibits parallel flat surfaces

(corresponding to the contact areas) and may develop
circumferential splits within the flattened surfaces.
Contributing Factors: Improper design-failure to account
for thermal or chemical volume changes, or excessive
compression.
Suggested solutions: Gland design should take into
account material responses to chemical and thermal
environments.
Spiral Failure
Description: The seal exhibits cuts or marks which spiral

around its circumference.
Contributing Factors: Difficult or tight installation
(static). Slow reciprocating speed. Low-modulus/hardness
elastomer. Irregular O-ring surface finish (including
excessive parting line). Excessive gland width. Irregular or
rough gland surface finish. Inadequate lubrication.
Suggested Solutions: Correct installation procedures.
Higher-modulus elastomers. Internally-lubed elastomers.
Proper gland design. Gland surface finish of 8-16 microinch
RMS. Possible use of polymer backup rings.
28
Compression Set
Description: The seal exhibits a flat-sided cross-section, the

flat side corresponding to the mating seal surfaces.
Contributing Factors: Excessive compression. Excessive
temperature. Incompletely cured elastomer. Elastomer with
high compression set. Excessive volume swell in chemical.
Outgassing/Extraction
Description: The failure is often very difficult to detect from

examination of the seal. The seal may exhibit a decrease in
cross-sectional size.
Contributing Factors: Improper or improperly cured
elastomer. High vacuum levels. Low hardness/plasticized
elastomer.
Suggested Solutions: Avoid plasticized elastomers. Ensure
all seals are properly post-cured to minimize outgassing.
Installation Damage
O-Ring Failures
Suggested Solutions: Low compression set elastomer.

Proper gland design for the specific elastomer. Confirm
material compatibility.
Description: The seal or parts of the seal may exhibit small

cuts, nicks or gashes.
Contributing Factors: Sharp edges on the glands or
components. Improper sizing of elastomer. Low-modulus/
hardness elastomer. Elastomer surface contamination.
Suggested Solutions: Remove all sharp edges. Proper
gland design. Proper elastomer sizing. Higher-modulus/
hardness elastomer.
29
Chemical Degradation
Description: The seal may exhibit many signs of

degradation including blisters, cracking, voids or
discoloration. In some cases, the degradation is observable
only by measurement of physical properties.
Contributing Factors: Incompatibility with the chemical
and/or thermal environment
Suggested Solutions: Selection of more chemically
resistant elastomer.
O-Ring Failures
Thermal Degradation
Description: The seal may exhibit radial cracks located

on the highest temperature surfaces. In addition, certain
elastomers may exhibit signs of softening-a shiny surface as
a result of excessive temperatures.
Contributing Factors: Elastomer thermal properties.
Excessive temperature excursions or cycling.
Suggested Solutions: Selection of an elastomer with
improved thermal stability. Evaluation of the possibility of
cooling sealing surfaces.
Explosive Decompression
Description: The seal exhibits blisters, pits or pocks on

its surface. Absorption of gas at high pressure and the
subsequent rapid decrease in pressure. The absorbed gas
blisters and ruptures the elastomer surface as the pressure
is rapidly removed.
Contributing Factors: Rapid pressure changes. Lowmodulus hardness elastomer.
Suggested Solutions: Higher-modulus/hardness
elastomer. Slower decompression (release of pressure).
30
Plasma Degradation
Description: The seal often exhibits discolouration, as well

as powdered residue on the surface and possible erosion of
elastomer in the exposed area.
Contributing Factors: Chemical reactivity of the plasma.
Ion bombardment (sputtering). Electron bombardment
(heating). Improper gland design. Incompatible seal
material.
Contamination
Description: The seal exhibits foreign materials on the

surface and/or within the O-ring.
Contributing Factors: Process environment deposition.
Reactions or degradation of the elastomer. Nonsemiconductor-grade elastomer.
Suggested Solutions: Specify contamination level
including manufacturing and packaging of the seals.
Abrasion
O-Ring Failures
Suggested Solutions: Plasma-compatible elastomer and

compound. Minimize exposed area. Examine gland design.
Description: The seal or parts of the seal exhibit a flat

surface parallel to the direction or motion. Loose particles
and scrapes may be found on the seal surface.
Contributing Factors: Rough sealing surfaces. Excessive
temperature. Process environment containing abrasive
particles. Dynamic motion. Poor elastomer surface finish.
Suggested Solutions: Use recommended gland surface
finishes. Consider internally lubed elastomers. Eliminate
abrasive components.
31
Material Guide
fluorocarboN (FKM, FPM)(Viton DuPont)
aflas (TFE/P)
-9C to +232C
+16F to +450F
-26C to +204C
-15F to +400F
Good high temperature capability

Resistant to strong acids and bases, amines, solvents and hot
water
Aflas is found in numerous applications in the oilfield
industry
Poor low temperature performance and low resilience
carboxylated nitrile (CBX, XNBR)
Material Guide
-20C to +135C
-4F to +275F
VITON EXTREME (FKM)(DuPont)
Increased strength, improved tensile and tear properties,

plus excellent abrasion resistance compared to a standard
Nitrile compound
Lower solvent swell
Excellent chemical resistance to petroleum oils and fluids
Commonly used in dynamic applications
Do not use with polar solvents, glycol brake fluids, aromatic
hydrocarbons, chlorinated hydrocarbons and strong acids
chloroprene (CR) (Neoprene DuPont)
-40C to +121C
-40F to +250F
ethylene propylenE (EPDM, EPR)

Excellent resistance to ozone, hot water, steam and aging

Wide temperature range
Commonly used with brake fluids and refrigerants
Poor resistance to petroleum fluids and mineral oils
32
-20C to +204C
-4F to +400F
Viton Extreme is a fluorocarbon compound that exhibits

significantly improved performance over regular Viton
Two types are available- TBR and ETP
TBR- Totally Base Resistant compound that provides
improved performance over other TFE/Propylene polymers
ETP- provides the excellent thermal resistance of Viton
along with significantly advanced chemical resistance
fluorosilicone (FVMQ)
-56C to +204C
-69F to +400F
Has exceptional ozone, weather, and good chemical

resistance
Good mechanical properties are retained over a wide
temperature range
Exhibits good resistance to refrigerants (R12)
-54C to +150C
-65F to +302F
Excellent resistance to higher temperatures, petroleum oils,

gasoline
Wide range of chemical resistance
Very good ozone, weather and aging resistance
Poor compatibility with H2S over 2%, amines, acetone, hot
water and steam
Poor low temperature characteristics although some
compounds are suitable to -40C/-40F

Excellent resistance to hydrocarbon fuels, petroleum oils
and silicone oils
Relatively low tear strength, abrasion resistance and tensile
strength
Generally not suited for dynamic applications
hIGHLY SATURATED NITRILE (HSN, HNBR)
-40C to +160C
-40F to +320F
A Nitrile based compound with improved chemical

resistance
Wider temperature range than standard Nitrile
High strength material that resists extrusion, abrasion and
wear
Water and steam resistance to +149C/+300F
H2S resistance up to 10%
Commonly used with petroleum oils and CO2
Do not use with chlorinated hydrocarbons, polar solvents or
strong acids
Low temperature compounds available down to -54C/-65F
polyurethane (AU, EU)
-54C to +105C
-65F to +220F
A thermoplastic elastomer able to handle high

temperatures and hostile fluids
Has excellent strength and toughness properties
Demonstrates high resilience and flexibility which permits
easier installation than PTFE materials
Not suitable with water and phosphate fluids above
+80C/+176F
A thermoplastic elastomer with higher tensile strength,

toughness and wear resistance
A good combination of hardness and elasticity
Good low temperature flexibility
Can be used in high pressure hydraulic systems where parts
are subject to wear
nitrile (NBR)
-70C to +260C
-94F to +500F
-40C to +120C
-40F to +248F
Presently the most widely used elastomer in the seal
industry
Provides an exceptional balance of good mechanical
properties, wear properties and chemical resistance
Resistant to most mineral oils and greases
Do not use with glycol based brake fluids and strong acids
Low temperature compounds to -54C
perfluoroelastomer (FFKM)
(Kalrez DuPont)
-15C to +250C
+5F to +482F
Has the broadest chemical resistance of any elastomeric

material
Combines the sealing integrity of elastomers with chemical
resistance approaching that of PTFE
Not suitable with liquid sodium and potassium, fluorinated
solvents and refrigerants
Compounds available to+325C/+617F
Kalrez 4079- A low compression set 75 durometer
compound with excellent chemical resistance, good
mechanical properties and outstanding hot air aging
properties.
Kalrez Spectrum 6380- An 80 durometer compound
specifically developed for chemical processes involving
hot, aggressive amines; in addition it has excellent overall
chemical resistance.
Kalrez Spectrum 7090- A 90 durometer compound that
is specifically targeted for use in applications requiring high
hardness/higher modulus properties. This compound has
excellent mechanical properties including compression set
resistance and explosive decompression resistance.
peEK
High strength
Able to retain its mechanical properties at high
temperatures
Commonly used for anti-extrusion purposes
Do not use with Hydrochloric, Nitric, or Sulphuric acids
ptfe (Teflon DuPont)

-200C to +250C
-328F to +482F
Has virtually universal chemical resistance
Very low coefficient or friction
Fillers such as bronze, moly, glass and carbon are commonly
added to alter mechanical properties
SILICONE (VMQ)
-65C to +232C
-85F to +450F
Material Guide
hYTREL (TPC- ET)(DuPont)

-54C to +149C
-65F to +300F
Excellent resistance to oxidation and ozone degradation

Most commonly used in static applications due to its poor
tensile strength and wear resistance
Popular for food and medical applications
Material information given is intended to serve as a general
guideline only. Actual testing in the application environment is
always recommended.
33
9211 - 41 Avenue,
Edmonton, Alberta T6E 6R5
Ph: (780) 438-6055
Fax: (780) 434-5866
www.hitechseals.com
Toll Free Phone: 1-800-661-6055

Toll Free Fax: 1-800-465-5866
Email: info@hitechseals.com
Bay #3, 5940 - 30 Street SE,

Calgary, Alberta T2C 1X8
Ph: (403) 720-2856
Fax: (403) 279-2662
www.hitechseals.com

Toll Free Fax: 1-800-321-0862
1180 Kerrisdale Blvd; Unit #8,

Newmarket, Ontario, L3Y 8Z9
Ph: (905) 953-9666
Fax: (905) 953-8739
www.hitechseals.com

Toll Free Fax: 1-888-580-SEAL (7325)
1450 Rue Nobel, Suite #20,

Boucherville, Qubec, J4B 5H3
Tl: (450) 655-SEAL (7325)
Tlec: (450) 655-7359
www.hitechseals.com
Tlphone Sans Frais: 1-866-894-SEAL (7325)

Facsimil Sans Frais: 1-866-904-SEAL (7325)
Courriel: info@hitechseals.com
Kalrez, Viton and Viton Extreme are registered trademarks of DuPont Performance Elastomers L.L.C.
Teflon and Hytrel are registered trademarks of the DuPont Company.
Aflas development by Asahi Glass Co., Ltd.
02/09
Canadian Owned and Operated

O Ring Brochure

Uploaded by

Copyright:

Available Formats

O Ring Brochure

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

O Ring Brochure

Uploaded by

Copyright:

Available Formats

Specialists in Seals & Service

O-Ring Sizing and Materials Guide

Choose Kalrez O-rings for the most harsh sealing conditions.

What makes Kalrez a superior elastomer?

Specialists in Seals & Service

Hi-Tech Seals - Popular Compound Specification Guide

A general service Nitrile compound for a wide range of applications

A low temperature Nitrile compound for use in applications where

Generally used for higher pressures than the 70 durometer materials,

This is a hydrogenated Nitrile compound which provides the material

Generally used for higher pressures than the 70 durometer materials

Generally used for higher pressures than the 80 durometer materials

Genuine Viton is generally used for higher pressure than the 75

Perfluroelastomer materials combine the best heat and chemical

Generally used for higher pressures than the 75 durometer materials

Tetrafluoroethylene-Propylene materials exhibit exceptional thermal and

Neoprene is a general purpose material for refrigerants, ozone and

Generally used for higher pressures than 70 durometer EPDM

Ethylene-Propylene materials exhibit excellent resistance to water,

Silicone compounds offer the widest elastomer temperature range but

Face Type Configuration

Selecting an O-Ring Cross-Section

elastomers like FKM or fluorosilicone

Advantages of Larger Cross-Section

Allows for larger tolerance while still

maintaining acceptable compression squeeze

a- wall angle b- break edge c- radius d- angle e- chamfer length

O-Ring C/S Squeeze (%)

HD- Hydraulic Dynamic Applications

HPS- Hydraulic & Pneumatic Static Applications

Rod Type seal

* Extrusion gaps should always be based on maximum diametral gap.

NOTE: The chart on the right is not to ISO

LIMITS FOR EXTRUSION

Total Diametral Clearance *

Fluid Pressure (psi)

There are different methods to counter O-ring

Fluid Pressure (Bar)

For hydraulic and pneumatic rod sealing applications

For hydraulic and pneumatic piston sealing applications

w- width of the O-ring axial housing, h- height of the seal housing

Original O-Ring C/S

Reduced O-Ring C/S at % ID Stretch (Inch/mm)

Compression Squeeze = C/S - H

Gland Fill (%) = O-ring CSA x 100

O-Ring Sizing Charts

O-ring Sizing Charts

Inch Standard (Actual)

Metric Standard (Actual)

Inch Standard (Actual)

Metric Standard (Actual)

O-ring Sizing Charts

O-ring Sizing Charts

Inch Standard (Actual)

Metric Standard (Actual)

Inch Standard (Actual)

Metric Standard (Actual)

O-ring Sizing Charts

O-ring Sizing Charts

Inch Standard (Actual)