Fioa0402u 16

FIOA-0402-U-16
Universal Analog I/O Modules
Field Analog Input Outputs.
FIOA-0402-U-16
Universal Analog I/O Modules :

Low cost compact Analog I/O modules with DIN rail mounting Programmable inputs allow same modules to accept RTD, Thermocouple, mA, mV and Volts 16 bit resolution 4 universal analog inputs and 2 analog outputs High Speed Modbus RTU (Slave) communication User definable Address, Baud rate and Parity through Software Configuration 2 wire RS485 port provided on pluggable terminal block Can be multi dropped as Modbus Slave on RS485 Network Indication for Diagnostics, Power and Communication Programming through standard Prizm software .........FREE!! CE marked with optional UL certification
Automation Simplified
Possible Applications :
FIOA can be used for various applications in industries. T ypical configuration includes the following :
1. Add analog I/O to your Controller.

Analog outputs (4-20 mA or 0-10VDC)
HIO 140
Analog inputs (mA, mV, RTD,Thermocouple,Volt)
2. Multiple FIOA units (Modbus Slaves) connected to Modbus Master

Node 1
~ ~
PLC Modbus Master
RS 485 Modbus Network
Node n
3. Data Acquistion Application (SCADA Connectivity)

Node 1
Node 2 Modbus RS485
~ ~
HMI Software ASTRA - by Renu Electronics Converter Example CNV-02 - by Renu Electronics Node n
* Images not to Scale.
Typical Wiring Diagrams :

1. Current Input Connections: 2. Voltage Input Connections:
V / mV
Analog Inputs
mA
CS
IN+ AGND
I-
CS
IN+ AGND I-
CURRENT
VOLTAGE & mV
3. RTD Input Connections:

RTD
4. Thermocouple Input Connections:

TC
CS
IN+ AGND I-
CS
IN+ AGND I-
3 WIRE RTD
THERMOCOUPLE
Analog Outputs
1. Current Output Connections:

Iout
2. Voltage Output Connections:

Vout
RL500 W
RL1000 W
VO IO A GND
VO
IO A GND
Specifications :
For mVolt inputs : Uses 0-100 mV input range resolved in 16 bits. Total error max : 0.2% of scale 1 LSB. For Current inputs : Uses 0-20mA input range is resolved in 16 bits. Total error max : 0.2% of scale 1 LSB. For Volt inputs : Uses 0-10V, 1-5V input range resolved in 16 bits. Total error max : 0.2% of scale 1 LSB. For RTD input : Uses 3 wire compensation technique. Excitation Current is 0.5mA. Power dissipated in RTD is 0.025mW @ 100 W. Range supported : -200 to 850OC. For Thermocouple Input : Uses 0-100mV input range resolved into 16 bits. Cold junction error is 1O maximum and 0.5O typical. Total error max : 0.5% of scale 1 bit + CJC error Response Time : Worst case 25mSec approx. Temperature Drift for Input and Output : 60 PPM max Normalization Factor : 0-99 (Software configurable)
Input Type J K E R S B N T Analog Outputs Resolution Load: 4-20 mA 0-10 V DC 16 Bit Less than 500 W Minimum 1k W Temperature Range -210 to 1200 C -200 to 1373OC -200 to 1000 C -50 to 1769 C -50 to 1769 C 0 to 1820 C -200 to 1300OC -200 to 400 C
O O O O O O
1 Bit Corresponds to 0.035 C 0.049OC 0.027 C 0.16 C 0.18 C 0.25 C 0.056OC 0.043 C
O O O O O O
General Specifications :
Power Operating Temperature Storage Temperature Humidity Mounting Size Immunity to ESD Immunity to Fast Transients Immunity to Radiated electromagnetic field Immunity to Conducted disturbances Surge Radiated emission : 24V DC 10%, 2.5W maximum O O : 0 to 50 C O : -20 to 80OC : 10% to 90% (Non condensing) : DIN rail mounting : 100 W x 70 H x 35 D mm : as per IEC61000-4-2 : as per IEC61000-4-4 : as per IEC61000-4-3 : as per IEC61000-4-6 : as per IEC61000-4-5 : as per EN61000-6-4 Communication Port : 2 wire RS485, RS232,CMOS logic Signals are available on RJ45 comm port. Same two wire RS485 signals are provided on terminal block : Modbus RTU Slave : 9600, 19.2k, 57.6k or 115.2k (software configurable) : Odd, Even or None (software configurable) : 1-255 (Software configurable) : 1.5KV isolation between communication ports, I/O and power supply section.
Driver Baud rate Parity Device ID Isolation
Basic Operations :
FIOA-0402-U-16 is Analog Input Output Model having 4 Universal Analog inputs and 2 Analog outputs. The ADC and DAC resolution is 16 bits. The Analog inputs can be Voltage (0-10V, 1-5V), Current (0 20 mA, 4 20 mA), mV ( 0 100 mV, 0 50 mV), RTD (PT 100 Alpha1 and Alpha2 constant), Thermocouple (B,R,S,E,J,K,N,T). Each input channel can be configured independently to work as any of the above type as per configuration made in the PRIZM software. The Analog outputs can be Voltage (0 10V) or Current (4 20 mA). Output channels also are software configurable to current or voltage. Unit supports standard Modbus RTU (slave) protocol for communicating with master device. Analog inputs and outputs are isolated from the communication port . Power supply is isolated from all internal circuitry. Input and Output channels of the FIOA are user configurable and any combination of input types is possible. Prizm Setup Software helps the user to configure the FIOA units and use them as per his requirements. System requirements for Prizm Setup Software are:
Device
IBM compatible PC with Pentium processor Operating System System RAM Hard disk VGA Monitor Color settings Resolution Mouse
Minimum
266 MHz Pentium II or higher Pentium compatible CPU Windows 2000 and above (except Windows Vista) At least 64 megabytes (MB) of RAM 150 MB free memory space 800x600 with 24 bit true color Microsoft mouse or compatible pointing device
Other Items required for FIOA configuration: 1. FIOA unit 2. +24VDC regulated power supply 3. Prizm Setup Software 4. FIOA to Device cable 5. Configuration download cable (IBM-005-H-00)
Dimensions :
70 .00
Pinout of COMM Port :
Pinouts of RJ connector is as shown below:

4. DATA+ (A) 3. GND 2. RS232 RX 1. RS232 TX 5. DATA- (B) 6. Terminal resistor 7. NC 8. CMOS_TX
100.00
PIN1
PIN8
COMM Port
35
All dimensions are in mm.
.00
FACTORY
Survey No. 2/6, Baner Road, Pune - 411045, India. Tel : +91 20 2729 2840 Fax : +91 20 2729 2839 Email : info@renuelectronics.com Website: www.renuelectronics.com
An ISO 9001 : 2008 and ISO 14001 : 2004 certified company
(Specifications subject to change without prior notice. DS-FIOA-0402-U-16 Family: Rev.F)

Fioa0402u 16

Uploaded by

Copyright:

Available Formats

Fioa0402u 16

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fioa0402u 16

Uploaded by

Copyright:

Available Formats

FIOA-0402-U-16

Universal Analog I/O Modules

Field Analog Input Outputs.

Universal Analog I/O Modules :

1. Add analog I/O to your Controller.

Analog inputs (mA, mV, RTD,Thermocouple,Volt)

2. Multiple FIOA units (Modbus Slaves) connected to Modbus Master

RS 485 Modbus Network

3. Data Acquistion Application (SCADA Connectivity)

Node 2 Modbus RS485

* Images not to Scale.

Typical Wiring Diagrams :

3. RTD Input Connections:

4. Thermocouple Input Connections:

1. Current Output Connections:

2. Voltage Output Connections:

Driver Baud rate Parity Device ID Isolation

Pinout of COMM Port :

Pinouts of RJ connector is as shown below:

You might also like