Plextor Plexwriter 820 Manual

Operation Manual
Model PX-R820Ti Internal and PX-R820Te External

CD Recorder/Reader
March 1999
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee interference will not occur in a particular installation. If this equipment
causes harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
For External Model Users: Please use the external shielded SCSI cables supplied with this
CD-ROM drive. Using other signal cables may exceed the limits of the Class B Part 15 of the
FCC Rules.
Any changes or modifications should be approved by the party responsible for compliance
of FCC Rules; otherwise, the user loses authority to operate the equipment.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified here-
in may result in hazardous radiation exposure.
The laser beam emitted from the optical pickup is invisible. Accordingly:
Do not open the optical pickup housing.
Obtain service only from Plextor-authorized personnel.
LASER INFORMATION
These products have been designed and manufactured according to IEC 825-1 on the Safety
of Laser products. This product comes under Class 1 Laser Products. A Laser Caution
Marking is attached on the top of the internal drive model: Caution: Invisible laser radiation
when open. Avoid direct exposure to beam.
CAUTION
To disconnect the CD-ROM drive from an electrical current, pull out the power plug.
VORSICHT
DIE TRENNUNG VOM NETZ ERFOLGT DURCH ZIEHEN DES NETZSECKES.
Zur Einhaltung der Funk-Entstrung von nicht selbstndig betreib-
baren Hochfrequenzgerten (periphere Anlagenkomponenten).
Dieses Gert entspricht als Einzelgert den Funk-Entstranfor-
derungen der Postverfgung Nr. 243/1991. Wird das Gert inner-
halb einer Anlage zusammen mit anderen Gerten betrieben. So
mu bei Inanspruchnahme der Allgemeinen (Betriebs-) genehmi-
gung nach der BMPT-AmtsblVfg Nr. 243/1991 die gesamte Anlage
folgenden Richtlinien entsprechen:
Grenzwertklases B der EN55022
Auflagen nach 2 der BMPT-AmtsblVfg 243/1991
Dies ist bei der Zusammensetzung einer Anlage (z.B. Computersystem) aus nur einzein
geprften Gerten nicht immer erfllt.
G-Vfg.243
CD Recorder/Reader
PX-R820Ti Internal
PX-R820Te External
Plextor reserves the right to make improvements in the products described in this manual at
any time without prior notice.
Plextor makes no representation or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any particular
purpose. Further, Plextor Corp. reserves the right to revise this manual and to make changes
in its content without obligation to notify any person or organization of such revision or
change.
This manual is copyrighted, all rights reserved. It may not be copied, photocopied, translated,
or reduced to any electronic medium or machine-readable form without Plextors prior
permission.
Manual copyright March 1999 Plextor Corp.
Licenses and Trademarks
All licenses and trademarks are property of their respective owners.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Internal Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
External Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
A Gentle Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. What Else Do I Need? . . . . . . . . . . . . . . . . . . . . . . . 6
4. Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5. Drive Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Panel Internal and External Drive . . . . . . . . . . . . . . . . 9
PX-R820Ti Internal Drive Rear Panel . . . . . . . . . . . . . . . . . 10
PX-R820Te External Drive Rear Panel . . . . . . . . . . . . . . . . . 11
6. Drive Switch/Jumper/Dial Settings . . . . . . . . . . . . . 12
PX-R820Ti Internal Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PX-R820Te External Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Other Switch/Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . 17
7. Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Internal Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
External Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8. Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . 20
Board Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Drive Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Mounting an Internal Drive . . . . . . . . . . . . . . . . . . . . . . . . . . 25
External Drive Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Regarding Soundcards and Audio Cables . . . . . . . . . . . . . . . . 32
Audio Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9. Software Device Driver Installation . . . . . . . . . . . . 33
10. Using CD-ROM/CD-R Discs and Trays . . . . . . . . . . 35
Tray Loading and Operating . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Handling CD-R Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cleaning the Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
11. How To Play Audio CDs on Your Drive . . . . . . . . . . 37
12. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Upgrading Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
12.1 PC Compatibles: Inital Installation . . . . . . . . . . . . . . . . . 42
12.2 PC Compatibles: Existing Installations . . . . . . . . . . . . . . . 49
12.3 Apple Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13. Contacting Plextors Technical Support Department 56
How to Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Before You E-mail/Log On/Fax/Call . . . . . . . . . . . . . . . . . . . . . 57
Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Helpful Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
14. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Appendix: Windows 95/98 Installation Guide . . . . . . . . 62
About Plextor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . 79
PX-R820T OPERATION MANUAL 1
Introduction
Thank you for purchasing the Plextor PlexWriter 8/20, a high performance and
reliable CD Reader/Recorder. We appreciate the confidence you have shown in us.
Our goal is to put you and keep you on the leading edge of CD technology.
To get you there, we first have to help you install your PlexWriter 8/20 drive properly
and operate it correctly. After that, the responsibility is yours to seek the applications
that make a CD-R such a powerful and exciting addition to your system.
Throughout this manual we will occasionally refer to the PlexWriter by the
general model number PX-R820T. We will also refer to the model numbers with a
lowercase i or e added to it to indicate internal or external, respectively. For
your purposes, all references apply to the PlexWriter 8/20 CD-R drive. (CD-R is a
common abbreviation for CD-Recordable drives and recordable CD media.)
For those of you with PCs, the installation process may seem a bit complicated
(Mac people have it easy). Fear not. We have successfully walked through the
installation process with millions of customers who previously had lived in mortal
terror of the innards of their computer.
In this manual you should find all the information you need to successfully install,
operate, and troubleshoot your drive. If you run into an unsolvable problem,
however, please contact us (see Chapter 13 for the different ways you can contact
us). You will be connected to our friendly, helpful band of tech support reps who
know their stuff. What might seem like an uncooperative CD-R drive to you could
very well be a 30-second fix to them. But we will never know unless you contact
us. If you are having trouble, please dont give up and take your drive back to where
you bought it until you have spoken with one of our tech support reps.
CHAPTER 1
This manual is designed to be followed in sequence. It is aimed primarily
at those who will connect their PlexWriter 8/20 drive to a PC.
Mac users should look for this symbol:
Users of UNIX-based systems
should look for this symbol:
as an indicator of sections of the manual that pertain to them.
Many of you reading this manual are experienced computer users who
have successfully installed peripherals in the past. There probably are a
number of sections in this manual that you can skip over. However, we ask
everyone from novice computer users to experienced computer
professionals to read the sections marked with this symbol:
2 PX-R820T OPERATION MANUAL
Box Contents
YOUR TASK: Check the contents of the box.
YOUR OBJECTIVE: Make sure you got everything you paid for.
YOUR METHOD: Compare what you find in the box with the tables on
the following pages.
What you find in your Plextor box depends on two factors: 1) what
configuration you purchased; and 2) what the company that sold you the box
put in or took out while it was in their possession.
Plextor currently sells its PlexWriter 8/20 drives in two configurations:
1) Drive with bundled software, including CD-mastering software for
PC, packet writing software, Plextors own CD Res-Q software for
HDD disaster recovery, Plextor Manager Utilities, and media. (We
may add more utilities as we uncover them.)
2) Drive kit with SCSI interface board, the software listed above, cables,
and media.
The drive kits come with either PCI bus-mastering SCSI controllers or PCMCIA
controllers for laptops. The configuration you received is indicated by stickers
applied to your box. Your drive may also have been integrated into a computer
system or subsystem sold by a third party.
NOTE: A security sticker was applied to the top of your box. The contents of
your box were carefully checked before this sticker was applied. If it
was cut before you purchased the box, you should carefully check the
contents to ensure nothing has been removed. If something is missing,
you should contact the party from whom you purchased the box for an
explanation.
There may be a good reason why the security sticker on the box was
cut before you received it. For example, a dealer may have purchased
a Drive Only configuration from Plextor, then added a SCSI interface
board and/or software purchased separately before selling the box to
you.
NOTE: If your drive came preinstalled, the rails, cables, interface boards and
other parts shown on the following pages may have been installed and
may not be separately available. Other accessories, especially
software, may not have been purchased from Plextor and thus may be
different from those sold in Plextor retail packages.
CHAPTER 2
DRIVE
SOFTWARE KIT SCSI KIT
CD-R drive
X X
4 mounting screws X X
Approved CD-R media (1 piece) X X
Plextor CD with
bundled software,
Plextor Manager, and CD Res-Q X X
SCSI interface board
and manual* X
Audio cable* X (2)
SCSI cable*
X
Plextor operation manual* X X
Warranty registration card X X
Extra jumpers for setting drive
switches
X X
CHAPTER 2 Box Contents
* Please see Chapter 13, page 59, for locations to purchase additional or replacement accessories.
Use the following tables to check the contents of your box:
PX-R820Ti Internal Drives
DRIVE
SOFTWARE KIT SCSI KIT
CD-R drive
X X
Approved CD-R media (1 piece) X X
Plextor CD with
bundled software,
Plextor Manager, and CD Res-Q X X
SCSI interface board
and manual* X
Audio cable* X
Power cable X X
SCSI cable*
X
Plextor operation manual* X
Warranty registration card X X
* Please see Chapter 13, page 59, for locations to purchase additional or replacement accessories.
PX-R820Te External Drives
A Gentle Reminder. . .
YOUR TASK: Save your box (if you received one).
YOUR OBJECTIVE: Have a secure container in which to ship your drive
back to Plextor, if necessary.
YOUR METHOD: Find an empty space in your home/office and fill it
with the Plextor box.
If you received your PlexWriter 8/20 CD-R drive in a Plextor box, you should
save the box after you have installed your drive. There are many sets of hands
some of them potentially unfriendly that a PlexWriter 8/20 might go
through on its way from us to you. Our box and its packaging material were
designed and drop tested to ensure that your PlexWriter 8/20 can endure
rough treatment and still arrive in working order.
We advise you to hold on to your box in case you should ever need to return
your drive to Plextor for any reason. Unfortunately, some of our customers
have not held on to their boxes and have had to resort to some
less-than-secure methods to get drives back to us. We have received drives in
a shoebox, in an unpadded express mail envelope, and in a box filled with
buttered popcorn.
We cannot assume liability for any damage your drive sustains during
shipment. Therefore, please ship your drive in the safest manner possible. We
believe your drive will be most secure if it is shipped in a Plextor box. We
hope you will never have to ship your drive back to us. If you do, however,
we hope you will send it packaged in a Plextor box.
If you did not receive a Plextor box (for example, your drive came pre-installed
in a computer), we recommend that you pay a packaging store (e.g., Mail
Boxes Etc.) in your area to ship your drive. The drives that we have received
from most packaging stores have arrived in good shape. If you dont have a
packaging store in your area, call our Technical Support Department for
packaging pointers before you ship your drive. In fact, you must call our
Technical Support Department to get an RMA number before returning any
drive (see Chapter 13).
What Else Do I Need?
YOUR TASK: Review the software and hardware installed in your
current computer system.
YOUR OBJECTIVE: Determine what else you may need to operate your
CD-R drive.
YOUR METHOD: Inventory your current computer system; check list
below.
If you purchased a Plextor box labeled Drive Kit with PCI SCSI Interface or
Drive Kit with PCMCIA Interface, your needs are simple: none. Everything you
need to successfully install and operate your PlexWriter 8/20 is included in the
box you purchased.
If you are a PC owner who has purchased a PlexWriter 8/20 Drive with
Software Kit, life gets a bit more complicated. These drives are intended for
purchase by those with SCSI adapters purchased or installed separately. They
do not have cables or a SCSI controller. Software Only packages are for those
who need a Plextor CD-R drive but prefer to use their own sources for all the
accessories. If you purchased a software kit, you will need to select cables and
a SCSI controller. The SCSI controller you own will fall into one of two groups:
1) You do not own a SCSI interface board.
In this case, you have to get one. Your local computer store and
numerous mail order vendors carry them. Due to the technical
demands of producing your own CDs, it is suggested that you buy a
high performance bus-mastering interface board. Older PIO SCSI
interface boards may not properly support CD recording. We suggest
you purchase a bus-mastering PCI card from any of the larger adapter
companies. See page 59 for suggested sources.
2) You own a SCSI interface board.
If you purchased your SCSI interface board several months or years
before you purchased your PlexWriter 8/20, you may need to update
your device drivers. See the discussion about Device Drivers in
Chapter 9 of this manual.
NOTE: We recommend that you do not use a SCSI interface built into a
soundboard.
CHAPTER 3
If you need to purchase a SCSI cable, note the following:
Internal Cables
You may already have a SCSI ribbon cable. If you are removing an existing
internal SCSI device and installing the PlexWriter 8/20, you can use the same
cable. If you are not removing an existing internal SCSI device, you may need
to purchase a different SCSI ribbon cable from your local computer supply
store. The cable must have at least as many connectors as you have SCSI
peripherals (including one for your PlexWriter 8/20), plus one additional
connector to attach to the interface board. Be sure to read the section on
Termination in Chapter 7 of this manual.
External Cables
If you have an external PlexWriter 8/20, you will need to purchase an external
SCSI cable. Make sure at least one end of the cable has the same kind of SCSI
connector as your PlexWriter. The other end of the cable must have the proper
connector to fit your SCSI controller or another daisy-chained external SCSI
device. Be sure to read the section on Termination in Chapter 7 of this manual.
You will also need:
Premastering Software
In order to create CD-R discs, you will need to have premastering software
installed on your computer system. You can check our web site (www.plextor.com)
for an updated list. We provide premastering software kits in retail packaging
for your convenience.
Once you have assembled everything you need, youre ready to install your
drive. But first, a few words of caution are in order.
CHAPTER 3 What Else Do I Need?
Precautions
YOUR TASK: Read the list of precautions below.
YOUR OBJECTIVE: Avoid any undo harm coming to you or your drive.
YOUR METHOD: Review the list and use common sense.
Your new PlexWriter 8/20 is a precision electromechanical device. Like the
rest of your computer system, it requires reasonable care in its installation and
use.
Please read this manual carefully and keep it handy for easy reference. Use
this manual for installation, operation, and troubleshooting. See your dealer or
call Plextors Technical Support Department should your drive require repair
or service.
X Do not put your computer monitor (or any other device weighing
more than 30 lbs.) on top of the PlexWriter 8/20 external drive.
X Do not place your drive in direct sunlight, on heating units, or near
electrical appliances that draw large amounts of current, such as a
high-powered audio amplifier, microwave oven, toaster, hair dryer, etc.
7 Keep the area around your drive clean from dust, smoke, and other
contaminants.
7 Use a soft, dust-free cloth for cleaning your drive. Do not allow
moisture or liquids including water, cleaning fluids, or solvents to
touch the drive. Thinner, benzene, or alcohol-based solvents can mar
your drives surface.
7 To help ensure that your CD-ROM discs remain free of dirt or other
contaminants, they should be stored in a jewel case. Use only industry
standard discs. Do not insert warped, poorly balanced, or cracked discs
into the drive.
7 Keep your CD-ROM disc clean. See Chapter 10 for tips on handling
and cleaning CD-ROM discs.
X Do not drop or jolt the drive.
X Do not attempt to open the drive and service it yourself. Removing the
cover may expose you to harmful electrical voltages or the laser beam.
For your safety, entrust service to Plextor-authorized service personnel
only.
CHAPTER 4
Drive Features
YOUR TASK: Get to know your drive.
YOUR OBJECTIVE: Learn how to operate different features of the drive.
Learn what goes where. Learn some terms that will
be used elsewhere in the manual.
YOUR METHOD: Match the parts of your drive to the diagrams below.
FRONT PANELInternal and External Drive
' Tray Front Door: Attached to tray drawer.
^ Eject Button: Push to eject tray. During CD play mode, playback is stopped
when pressed once and the disc ejects when pressed twice.
Emergency Eject Hole: Insert emergency eject stick, paper clip, or other
thin, rigid object to eject tray if automatic eject button does not work. Turn
OFF power before using this feature.
CD-Audio Play Button: With audio CD in drive, push once to put drive in
CD-Audio play mode. Push button once during CD play mode to skip
tracks. Push and hold down play button more than one second to fast
forward.
I Write Speed Indicator: Orange when recording at 1X, 2X, 4X and 8X
speeds.
CHAPTER 5
Door Closed
' Tray Front Door
^ Eject Button
^ Headphone Jack
I Volume Control
I DISC Indicator
I
1X, 2X, 4X, 8X
Write Indicators
CD-Audio Play Button
Emergency Eject Hole
I ON/READ Indicator
I ON/READ Indicator: Green when power is ON and no disc is in drive.
Green flashing when disc is being accessed.
I Disc Indicator: Green when disc is in the drive and power is ON.
I Volume Control: Controls volume of headphone jack. This control has no
effect on the rear panel audio outputs.
^ Headphone Jack: Stereo mini-jack for headphones and powered speakers.
PX-R820Ti Internal DriveREAR PANEL
' Audio Output Connector: Outputs stereo analog signal. Use to connect to
soundboard or audio amplifier. Use standard MPC-3, type 4-pin connector.
^ Jumpers: Use to select SCSI ID number, parity, termination, or block size.
Leave these jumpers at their factory settings unless one or more of the
following situations pertain to you:
SCSI ID number: If you are using more than one SCSI peripheral, you
may have to change your SCSI ID number (see page 14).
Termination: Review Chapter 7 to determine if you need to turn your
terminator switch off.
Block size: If you are working in a UNIX environment and want to boot
from your CD-R drive, see page 15.
SCSI Interface Connector: Connects to SCSI interface board using 50-pin
to 50-pin flat ribbon SCSI cable.
Power Connector: Connects to your computers power supply (DC +5V and
+12V).
CHAPTER 5 Drive Features
' Audio Output Connector
SCSI Interface Connector ^ Jumpers Power Connector
PX-R820Te External DriveREAR PANEL
' DIP Switches: Use to select parity, termination, test, block size, or eject
lock. Leave these jumpers at their factory settings unless one or more of the
following situations pertain to you:
Termination: Review Chapter 7 to determine if you need to turn your
terminator switch OFF.
Block size: If you are working in a UNIX environment and want to boot
from your CD-R drive, see page 16.
Eject lock: If you work in an environment where you need to prevent
others from removing a CD-R disc from your drive, see page 16.
^ SCSI ID: Use this dial to designate SCSI ID numbers. Rotate the dial to
change the number. If you are using more than one SCSI peripheral, you
may need to change your SCSI ID number (see page 15).
Power Switch: To turn power ON/OFF.
AC Power Input: Use the power cord supplied with your drive.
I Audio Output: Outputs stereo analog signal. Use to connect to soundboard
or audio amplifier. Use standard RCA jack connectors.
I SCSI Interface Connector In and Out: One connector should be used to
link your CD-R drive to your SCSI host adapter; the other to link your CD-R
drive to another SCSI peripheral with a daisy chain cable (see page 31). You
may use either connector for either purpose.
CHAPTER 5 Drive Features
I SCSI Interface Connector
' DIP Switches
I Audio Output
Connectors
AC Power Input
^ SCSI ID
Power Switch
CHAPTER 6
Drive Switch/Jumper/Dial Settings
YOUR TASK: Find the locations of the jumpers (internal drive), the
switches, and the rotary dial (external drive). Check
their settings. Change them, if necessary.
YOUR OBJECTIVE: To ensure that your new CD-R drive can coexist with
other equipment you might have installed in your
computer. To ensure that your drive will work
properly after it is installed.
YOUR METHOD: Find the locations of the jumpers, the switches, and
the rotary dial on the diagram in Chapter 5. Read
below to determine if your drives settings need to be
changed. If so, follow the directions for making the
necessary changes.
Your PlexWriter 8/20 needs to be flexible enough to work with the variety of
computer systems (PC, Mac, Sun, Silicon Graphics, DEC, etc.) that can use
SCSI peripherals. To provide this flexibility, Plextor gives its customers options
on the drives settings before it is installed. On an internal drive, settings are
determined by the position of jumpers on the jumper block at the rear of the
drive. On an external drive, settings are determined by the position of DIP
switches and the rotary dial on the rear panel of the drive.
Fortunately, we have a pretty good idea of the environment in which most of our
drives will be used (a single SCSI device connected to a PC or Mac). Your drive
ships from our factory with its jumpers, switches, and/or dial set to work in this
environment.
You should leave the jumpers found on the rear panel of the PX-R820Ti and
the switches and rotary dial found on the rear panel of the PX-R820Te at their
factory settings, unless: 1) you plan to use another SCSI peripheral (e.g.,
CD-ROM, hard disk, scanner) with your computer system in addition to your
CD-R drive; or 2) you find it necessary to change the device type setting (most
likely in an older UNIX system).
If you plan to use additional SCSI peripherals, you may need to change the
jumper, switch, and/or dial settings of the PX-R820Ti/PX-R820Te. This section will
describe how to make these changes.
If the CD-R drive is the only SCSI peripheral you will use with your computer
and you do not need to change the device type setting, skip now to Chapter
8: Hardware Installation. (Take our word for it, most of you can now skip to
Chapter 8.)
PX-R820Ti Internal Drive
Factory Setting of Jumper Block
The functions shown are ON if the jumpers are installed and OFF if the
jumpers are removed. The jumpers are set by the factory as follows:
Installing and Removing Jumpers
Ensure power to the drive is OFF before installing or removing jumpers.
To remove a jumper, pull it off with your fingers or a pair of needle-nose pliers.
To add a jumper, push it onto the jumper pins. Extra jumpers are supplied with
the PX-R820Ti in addition to the three jumpers already installed at the factory.
CAUTION: Install jumpers across each pin as shown. Do not connect one pin
switch to another by installing the jumpers lengthwise. Doing so
could result in damage to the drive.
Install jumpers this way
(Vertically)
CHAPTER 6 Drive Switch/Jumper/Dial Settings
ON (Jumper installed)
OFF (Jumper removed)
SCSI-ID
PARITY
TERM
BLOCK SIZE
TEST
DO NOT install jumpers this way
(Horizontally)
Jumper
EJECT LOCK
SCSI ID Number
It is possible to chain (using a daisy chain cable) SCSI peripherals to a single
SCSI interface board, or to the SCSI port of an Apple computer up to seven
devices with the PlexWriter 8/20. Daisy chaining a few drives together should be
possible with no loss of performance. When using multiple SCSI peripherals,
however, it is necessary to set each peripheral to a unique SCSI ID number.
NOTE: To guarantee specified performance, cable length of all daisy chain
cables and cabling in external case should not exceed 1.5 meters. It is
physically impossible to daisy chain 15 external drives with total cable
length under 1.5 meters.
If you bought a Plextor kit with a SCSI interface board, both the drive and the
board are SCAM compliant, which means each time you turn on your
computer, the drive will internally reset its SCSI ID to avoid any conflict. If you
separately purchased or already own a SCSI interface board, it may not be
SCAM compliant.
For those of you without SCAM adapters, your Plextor CD-R drive can be set
to use one of eight SCSI ID numbers. The drive should arrive with its SCSI ID
set to 4. Accordingly, if you already use another SCSI peripheral, and its SCSI
ID is also set to 4, you must change the SCSI ID number of either this
peripheral or the CD-R drive. In the past, this always had to be done manual-
ly. If you connect your PlexWriter to an existing SCSI controller, you will still
need to go through this exercise of checking and possibly changing SCSI IDs.
Changing the SCSI ID: PX-R820Ti
The SCSI ID number of the PX-R820Ti is determined by the placement of
jumpers on Pins 1, 2, and 3. To find the location of Pin 1, Pin 2, and Pin 3,
refer to the diagram on page 13. To change the SCSI ID number, follow the
chart below.
Jumper Installed Across
SCSI ID Number Pin 1 Pin 2 Pin 3
0 OFF OFF OFF
1 ON OFF OFF
2 OFF ON OFF
3 ON ON OFF
4 OFF OFF ON
5 ON OFF ON
6 OFF ON ON
7 ON ON ON
For example, the factory setting for SCSI ID 4 is made by installing a jumper
across Pin 3 of the jumper block, leaving Pin 1 and 2 uncovered. To set the
SCSI ID at 7, you would install a jumper across Pin 1, another jumper across
Pin 2, and a third jumper across Pin 3. To set the SCSI ID at 2, you would
install a jumper across Pin 2, leaving Pins 1 and 3 uncovered.
Factory Settings
PX-R820Te External Drive
SCSI ID Number
Please see description page 15. It is also applicable to the external drive.
Factory Setting of Dial and DIP Switches
CAUTION: Turn the drives power OFF before changing the setting of the dial
or DIP switches.
The SCSI ID number of the PX-R820Te is determined by the position of the
pointer on the SCSI ID rotary dial. The drive will arrive with its SCSI ID set to
4. The rotary dial and DIP switches are set by the factory, as shown below:
Changing the SCSI ID
Using the blade of a screwdriver, rotate the dials arrow to a different SCSI ID
number.
PARITY
(ON) 1
(OFF) 0
TERM
TEST
BLOCK
SIZE
EJECT
LOCK
Other Switch/Jumper Settings
PX-R820Ti/PX-R820Te
The remaining switches (external drives) and jumpers (internal drives) are:
Parity Leave this ON. The parity check provided by the ON setting
enhances the reliability of the SCSI bus. Set to OFF only if your
computer system or SCSI controller specifically requests that pari-
ty be disabled.
Term This enables or disables (turns ON or OFF) SCSI termination.
Factory setting is enabled (ON). See page 18 for an explanation of
SCSI termination and to determine if you need to change this set-
ting.
Test Leave this OFF. It is for factory use only.
Block Leave this OFF, unless you are working in a UNIX environment
and want to boot from your CD-R drive. If so, set this
switch/jumper ON.
Eject Lock Leave this OFF, unless you work in an environment where you
need to prevent others from removing a disc from your drive.
Termination
YOUR TASK: Find the location of the SCSI termination jumper or
switch.
YOUR OBJECTIVE: Determine if you must disable the SCSI termination.
YOUR METHOD: Your drive was shipped with termination enabled.
If necessary, remove the termination jumper or turn
the SCSI termination DIP switch OFF by following the
instructions below.
You must enable SCSI termination if the PlexWriter is the only SCSI peripheral
used with your computer. In addition, you must enable termination (ON) if you
are using multiple SCSI peripherals with your computer and the PlexWriter is
positioned as the last peripheral in a daisy chain. If you are using an Ultra SCSI
host adapter, we recommend using active termination.
NOTE: The PlexWriter uses active termination.
If you have internal SCSI peripherals only, or external SCSI peripherals only
(but not both), then you should be using an internal ribbon cable or external
cable (or cables), respectively (but not both). In this case, all devices between
the host adapter and the last peripheral on the opposite end of the ribbon
cable, or the last peripheral at the end of your daisy chain, should have their
termination removed, disabled, or turned off.
If you have both internal and external SCSI peripherals (both the internal and
external connectors of your host adapter are used), then the termination of
your SCSI host adapter should be removed, disabled, or turned OFF. The last
peripheral on your internal cable and the last peripheral on your external daisy
chain should retain their termination. All other SCSI peripherals connected to
the host adapter should have their termination removed, disabled, or turned off.
NOTE: Some host adapters and peripherals have the ability to disable and
enable termination power. This should not be confused with termination
itself. Termination power can and should be provided by at least one
device attached to your SCSI host adapter. Your Plextor drive
automatically supplies termination power. Any additional devices
supplying termination power will not cause any problems.
CHAPTER 7
REMEMBER: Only the last SCSI peripheral in a daisy chain should have
termination enabled. If you have any SCSI devices chained after
your PlexWriter, you must disable or turn OFF the PlexWriters
termination using the following instructions:
Internal Termination
The PlexWriter internal drive is shipped from the factory with its termination
enabled (ON).
To disable termination, remove the jumper from the termination pins on the
back panel of your drive. Refer to the diagrams on page 13 for the location of
the termination pins (labeled Term). They are the second set of pins from the
left.
If your drive is already installed in your computer, be sure to turn off your
computer before removing (or reinstalling) the jumpers. We recommend that
you retain the jumpers so you can reinsert them onto the termination pins if
you later need to turn the drives termination ON.
External Termination
The PlexWriter external drive is shipped from the factory with its termination
turned ON.
To turn the termination OFF, first turn off the drives power, then change the
second DIP switch on the rear panel of the drive to the OFF position. Refer to
the pictures on page 16 for the location of the termination switch (labeled
Term). It is the second of the five switches.
CHAPTER 7 Termination
Hardware Installation
By itself, your PlexWriter 8/20 is incapable of communicating with your
computer. You must use a hardware link that enables your drive to talk with
the rest of your computer. PlexWriter 8/20 uses a SCSI interface as its link.
Plextor strongly recommends the use of a high performance bus-mastering
SCSI interface board, preferably a PCI card. You may have purchased a Plextor
kit with such a board included. If you purchased your PlexWriter 8/20 without
a SCSI interface board, we suggest you do not connect it to a non-bus-mastering
interface board (PIO). If you use an ISA bus-mastering card, we recommend
you do not connect any other SCSI peripherals to the same board. Connecting
the PlexWriter 8/20 to a parallel-to-SCSI or to the SCSI interface on a
soundboard is not recommended, as it will slow performance.
CHAPTER 8
Board Installation
YOUR TASK: Install a SCSI interface board in your computer.
YOUR OBJECTIVE: Provide the hardware link needed to enable your
CD-R drive to communicate with your computer.
YOUR METHOD: Remove your computers case. Install board and
attach necessary cables.
Let us point out that this is a CD-R drive installation and operation manual
it is not a SCSI interface board operation manual. Unless you purchased a SCSI
interface board (and its accompanying manual) bundled in the same box with
a PlexWriter 8/20, we have no way of knowing which type of board you elect
to use. There are dozens of SCSI interface boards on the market. Each one is
installed somewhat differently. Therefore, instructions for this section should
only be considered as guidelines. For more detailed instructions on how to
properly install your SCSI interface board, you should refer to the operation
manual that you received when you purchased the board.
CAUTION: If static electricity may be present in the room where you are
working, discharge any you may have on your body by touching a
grounded object before you remove the host adapter from its
packaging.
Static electricity is a silent killer. Just a small jolt to one of the
chips on your interface board may render it useless with no
apparent damage. Positioning your computer in a location
without a carpet underfoot is one method of guarding against
static electricity damage. Using common sense, such as not
walking on a carpeted floor in stocking feet just before you install
your drive, is another.
Before proceeding, make sure the power to your computer and
any external peripherals are OFF and your computer is
UNPLUGGED from its power source.
CHAPTER 8 Hardware Installation
To remove your computers cover, follow the directions provided by your
computers manufacturer. Typically, this involves loosening or removing
several screws on the back panel of your computer and sliding off your
computers cover.
Carefully remove the SCSI interface board from its packaging. Select a vacant
slot in your computer where you will install the board (refer to the manual
packaged with your interface board for instructions as to which slot in your
system to use). If you are installing an internal drive, try to pick a slot that is
closest to where the drive will be installed.
Remove the cover plate for this slot from the back panel of your computer.
Keep the screw from the cover plate nearby, as you will need it in a moment.
Save the cover plate in case you need it at a later date.
Plug the SCSI interface board into the slot you have selected. Rock the board
from end to end to ensure that it sits firmly in the slot. Dont force it. If you
cannot push the board down completely into the slot, remove the board and
try again.
Expansion Slot Cover
Rear Panel
Once you have successfully inserted the board, fasten it in place using the
cover plate screw that you removed earlier.
Drive Positioning
YOUR TASK: Determine where you want to install your drive.
YOUR OBJECTIVE: Position the drive in the proper manner so that it
operates correctly.
YOUR METHOD: If you have an internal drive, find an open bay in
your computer. If you have an external drive, find an
open space on your desktop.
The PlexWriter 8/20 should only be installed horizontally. When the drive is
in a vertical position, the disc may not always be flat against the tray drawer.
The write head may lose contact with the disc surface and cause write errors
during recording. Therefore, we do not recommend installing this drive
vertically.
Horizontal Horizontal
NOTE: The following section is only for those installing internal drives. If you
have an external drive, skip to page 29.
Mounting an Internal Drive
YOUR TASK: Mount your internal drive inside your computer.
YOUR OBJECTIVE: A securely positioned drive whose connectors are
within easy reach of the various cables that must
attach to it.
YOUR METHOD: Identify the drive bay where you will mount your
drive. Remove bay cover. If necessary, use mounting
rails to install drive in bay.
Your PC probably looks something like this:
You can mount your drive in any available bay. You must remove the small
panel that covers the bay that you want to use. Typically, this is done after you
have removed your computers cover. The panel can then be popped out by
pressing outward lightly (in some older cases you may have to remove screws
that hold the panel in place).
You now need to determine if you must install mounting rails on the sides of
your drive. To do so, insert the drive into the open bay. If the drive fits tightly
with little or no clearance on either side of the drive, you will not have to use
mounting rails. The drive can be mounted directly into your computer.
CAUTION: Do not mount your drive in your computer using screws other than
those supplied by Plextor. You may damage the drive if you insert
screws that are too long.
Available bay with
cover panel removed
If you must use mounting rails, install them as shown below:
NOTE: Plextor does not provide rails. If rails are necessary, it is up to the
computer/chassis manufacturer to provide them.
There are four holes provided on each side of the drive. To mount an internal
drive in most computers, the rails should be fastened to the lower pair of holes.
In some instances, you may need to fasten the rails to the upper set of holes.
You will find that four screws were supplied with your drive. Use only these
screws. After fastening the rails, check their positioning by sliding the drive
into the bay before you connect any cables.
Check Your Jumper Settings
Once you have determined: a) that you have properly mounted the rails; or
b) that you dont have to use mounting rails, you are almost ready to finish
your drives installation. However, before doing so, check your jumper settings
one last time and be sure to record the serial number of your drive for future
reference. It may also be helpful to record the TLA code found on the back
or top of your drive.
If you have no other SCSI peripherals (e.g., CD-ROM, hard disk, scanner, print-
er, etc.) in your system other than your CD-R drive, you should not change the
jumpers from their factory setting or remove the termination resistors.
If you have other SCSI peripherals as part of your computer system, you may
need to change the settings of the SCSI ID and/or remove the termination
jumper. See Chapters 6 and 7 for information on how to change these settings.
Be sure not to mistake the inner and
outer face of the rail when attaching.
Typically, the smooth side of the rail
faces away from the
drives chassis.
Cable Connections
You must make a minimum of two cable connections to your CD-R drive. A
third cable connection will need to be made if you are using a soundboard in
your computer and plan to connect the PlexWriters audio output to the audio
connector on the soundboard.
The two cable connections that you must make are:
1) SCSI cable
2) power cable
The SCSI cable you will need is a standard 50-pin flat-ribbon cable. If you
already have one other SCSI peripheral (such as a hard disk) and your existing
cable has only two connectors, remove the cable and replace it with a cable
with additional connectors. Connect the SCSI host adapter to a connection on
either end of the cable. Connect the two peripherals to the other two
connectors (one at the middle connector and one at the end of the cable).
Refer to Chapter 7 of this manual for setting the termination of the devices.
CAUTION: It is easy to accidentally plug your SCSI ribbon cable upside down
into both your drive and SCSI interface board. Accordingly, be
sure you match the red stripe along one side of the SCSI cable to
Pin 1 on the interface board and Pin 1 on the drive. Each
connector on the ribbon cable has a key in the middle. This key
should fit into a slot in the middle of each connector of the
interface board, your PlexWriter, and any other internal SCSI
peripherals.
Double-check your work. You must ensure the side of the SCSI
cable with the red stripe is matched to Pin 1 on the interface
board and on the drive.
Personal Computer
Audio Connector
Jumpers
DC Power Supply
DC+12V 0.6A
DC+5V 0.3A
Power Supply
from Personal
Computer
SCSI Interface Connector
Power Connector
SCSI Ribbon Cable
SCSI Host Adapter
The easiest way to install your SCSI cable is to plug it into the SCSI connector
on the rear panel of the drive before you insert the drive into your computer.
Then you can thread the cable through the front of the open bay you plan to
use and back toward the SCSI interface board. Connect the cable to your SCSI
interface board and finish mounting your drive in the proper position. The
drive should slide smoothly into the bay. If it does not, check for obstructions
in the bay and ensure the side rails (if needed) are attached properly.
You now need to make the power connection. In most computers, you will
find additional power connectors that are ready for your use. Check the cable
running from your power supply to your hard disk and see if it has extra
connectors on it. If so, you can plug one of these into the power connector
found on the rear panel of the CD-R drive.
If you do not find any additional connectors (either because they were not
supplied or they are all in use), you will have to buy a splitter or a Y-connector.
These can also be found at most computer stores.
A third cable, an audio cable, must be used if there is a soundboard in your
system. This cable runs from the four-pin audio output connector on the rear
panel of your drive to your soundboard. See page 32 for more information
about audio cables.
To Pin 1
Either end of the cable may be connected
to the CD-R drive or the SCSI interface
board
Pin 1
#1
Installation of your internal drive is now complete. Skip to page 32.
External Drive Installation
YOUR TASK: Connect cables from your external drive to your PC
or Mac. Check to see if switch, dial, and terminator
settings need to be adjusted.
YOUR OBJECTIVE: A well-functioning drive that does not conflict with
any other peripherals in your computer system.
YOUR METHOD: Follow the directions below for making cable
connections. Review your current computer setup to
see if potential conflicts exist. If so, make the
necessary switch, dial, and/or terminator changes.
If you are installing a single PX-R820Te and you have no other SCSI
peripherals attached to your system, you should leave the switches, dial, and
terminator found on the rear panel of your drive at their factory settings. If you
do have additional SCSI peripherals (e.g., CD-ROM, scanner, printer) attached
to your computer, you may need to change your dial and terminator settings.
See Chapters 6 and 7 for information on how to change these settings.
If you are installing a single PX-R820Te external drive, connect it as shown on
the next page.
PC Connection
SCSI Cable
SCSI Interface Board
Personal Computer
Y
AC Power
Supply
PX-R820Te Rear Panel
If you are installing more than one PX-R820Te external drive (or one
PX-R820Te and other external SCSI peripherals), connect them as shown
below:
NOTE: Performance of SCSI devices may suffer if total cable length in daisy
chain plus cabling in external case exceeds 1.5 meters. Assume
cabling in external case equals about 20cm when adding up total
cable length. Quality of cabling is also important. Use shielded cables
when possible.
PC or Mac Connections Multiple Drives
Personal Computer
SCSI Cable
All connections are
50-pin High Density
No terminator
No terminator
Termination enabled using
DIP switch setting
SCSI
Interface
Board
Daisy
Chain Cable
Regarding Soundcards and Audio Cables
Whichever category your soundboard falls into, you will find that the best
source of information about installing the soundboard in your computer is
your soundboard's manual. Once you have successfully installed the
soundboard in your computer, you can continue below for a description of the
different cable connections that need to be made. Plextor strongly suggests
you not use the SCSI connection on your soundcard to control your PlexWriter
8/20.
Audio Cables
Plextor provides audio cables in kits which also include SCSI controllers
because we are assuming this will be the primary, or possibly the first, SCSI
CD-ROM in your system. Our bare drive kits include no cabling. In kits with
a SCSI card, two cables come with an internal kit and one set with an external
kit. One cable delivered with your internal drive is MPC compliant, and the
other has connectors designed for use with Sound Blaster sound cards. The
cable delivered with your external drive has two RCA-type color-coded con-
nectors at one end, which connect to your drive, and a single stereo mini-jack
at the other end, which plugs into the line-in receptacle on your soundboard
(at the back of your computer).
If you purchased an internal drive SCSI card kit and you have a soundcard
other than SoundBlaster that is not MPC compliant, you will have to purchase
a different audio cable from a computer supply store. We can help by
recommending several vendors who offer audio cables and can get them to
you quickly at a reasonable price (see page 59).
The following diagram illustrates where the SCSI cable and audio cable need
to be connected to your internal CD-R drive:
Soundboard without SCSI Interface
1 Audio Connector
2 Power Connector
3 SCSI Connector
Software Device Driver
Installation
YOUR TASK: Install the correct version of software device drivers
into your computer system.
YOUR OBJECTIVE: Enable your CD-R drive to communicate with the rest
of your computer system.
YOUR METHOD: Insert the floppy disk containing the device drivers
into your floppy disk drive. Follow the directions
provided by their supplier in order to copy the drivers
to the proper location in your computer.
A device driver is a software program that allows your computer to interact
with your drive. If you do not use a device driver, or you use an outdated
version of the required device driver, you will not be able to operate your
PlexWriter 8/20. The lack of a device driver, or the use of an improper version
of a device driver, are the most common causes of calls to Plextors Technical
Support Department.
For the purpose of setup and installation, the primary source of the device
driver you require to support your PlexWriter 8/20 CD-ROM function should
be your operating system or Plextor. Your PlexWriter 8/20 acts as a CD-ROM
drive for the purpose of setup and installation. This allows it to be easily
recognized and supported by the generic CD-ROM device driver files in
Windows 95 or OS/2 Warp, as well as the DOS/Windows driver provided in
Plextor Manager. Even if you are not running DOS or Windows 3.11 and do
not need the Plextor Manager device driver, there are other valuable utilities
provided with Plextor Manager. We recommend you review the separate
manual for this software to determine if you want to install these utilities.
NOTE: Mac users must purchase device drivers separately.
Additionally, software called packet writing or DLAsoftware allows you to use the
drive as a read/write CD-ROM drive in Windows 95/98 and possibly NT 4.0. If you
purchased a retail kit with software and/or SCSI card, this software is included.
You will also need to have an ASPI Manager file for DOS/Windows 3.x or a
mini-port driver file (.MPD) for Windows 95/98 to support your SCSI host
adapter. ASPI Managers are provided by SCSI host adapter manufacturers.
Mini-port drivers are generally included with Windows 95/98. However, if
CHAPTER 9
your SCSI host adapter was released recently, it may not be supported by your
release of Windows 95/98 and NT. In this case, you should contact the host
adapter manufacturer who should have provided the required .MPD file. If you
bought a PlexWriter kit with a SCSI host adapter, Plextor has included the
applicable ASPI Manager and *.MPD files with your Plextor Manager software.
A more common problem is that the CD-ROM ASPI Manager and/or the
Device Driver that you received with your SCSI interface board at the time of
purchase needs to be updated in order to work with your PlexWriter 8/20. SCSI
interface board manufacturers are continuously updating their ASPI Manager
to provide support for new SCSI peripherals as they enter the market. Most of
these companies will provide you with an update at little or no cost. In addi-
tion, if you have a modem, you can call the bulletin board or web site that
many of these companies maintain and download the most recent version.
Before installing drivers, check that all the cable connections between your
CD-R drive and PC are correct and that all switches, dials, and termination are
set properly. If you are using a PX-R820Te external drive, turn the power
switch to OFF. Once the drive installation is complete, remember to turn the
drives power ON before turning your computer on.
If you purchased a drive kit with software or a drive kit with a SCSI host
adapter and software, we have included a special Plextor device driver for use
with a DOS or Windows PC. This device driver was custom designed by
Plextor to ensure optimum reading performance of your PlexWriter. Please
refer to the separate Plextor Manager Users Manual provided for PC
installation.
If you are installing your drive on a UNIX workstation, please refer to your
systems documentation. UNIX operating systems also provide CD-ROM device
drivers. Remember, third party software is required for mastering and
recording CDs.
All of the above issues regarding device drivers are primarily applicable to
operating your PlexWriter 8/20 as a CD-ROM device (reader) and for the drive
to be recognized by your operating system. In order to take advantage of the
PlexWriter 8/20s ability to record on CD-R media, you will also need special
software. We recommend purchasing CD-mastering software and packet writ-
ing software, which also happens to be included in all Plextor software and
SCSI kits. Plextor also provides a HDD disaster recovery program in these kits
called CD Res-Q. For those who purchase a bare CD-R drive and own a
Plextor 12PleX or faster CD-ROM, the DiscDupe feature of Plextor Manager
will allow you to copy CDs directly from the CD-ROM to the CD-R drive.
CHAPTER 9 Software Device Driver Installation
Using CD-ROM/CD-R
Discs and Trays
YOUR TASK: Learn how to handle, load, and care for your discs.
YOUR OBJECTIVE: Protect your discs. Insert and eject discs properly so
your drive operates without interruption.
YOUR METHOD: Practice loading discs into trays.
Tray Loading and Operating
1) While the drive is powered up, push the Eject button. The tray drawer
will slide out in 23 seconds.
2) Lay the bare CD into the
depression in the tray, label side
up. The CD should lay flat in the
drive; you do not need to use the
clips in the tray.
3) Press the Eject button again and
the tray will slide shut within
seconds.
NOTE: We recommend you use the Eject button to close the tray in a smooth
and secure manner. Closing the tray by pressing the front of the
drawer by hand is not recommended and risks damage or premature
wearing of the mechanism.
CHAPTER 10
Handling CD-R Media
Care should be taken when handling CD-R media. Dust, scratches, and finger
prints on the data side of the disc can cause write errors during recording. When
picking up or holding CD-R media, you can either place your fingers only on
the outer edge of the disc or place one finger through the center hole and one
finger along the outer edge. Once you are finished creating a disc, you can
then label it by writing on the top using permanent ink or by using self-sticking
CD-R labels.
NOTE: We recommend placing self sticking CD-R labels after recording as the
weight of the label may unbalance the disc and cause write errors during
recording.
Cleaning the Disc
For proper read and write performance, it is important that your CD-R and
CD-ROM discs be clean. Trying to record on a dirty disc may result in a failed
session and ruin the disc.
If the disc is merely dusty, you may use a commercially available dust removal
spray such as Dust-Off or Vari-Air to blow dust particles off the disc. You
should not use liquid or chemical cleaners. They may damage the disc and
make it unusable.
After removing the dust particles, you may wipe the disc using a clean, soft
cotton cloth to remove surface dirt such as fingerprints. Use a straight-line
motion, wiping from the center out. Do not wipe the disc in a circular motion.
If CD-R media becomes dirty or soiled with grease or other contaminants not
removable by wiping, you should probably discard the disc. It will probably
fail during the recording process.
HINT: Keeping your frequently used CD-R and CD-ROM discs in jewel cases
at all times will prevent them from becoming dirty or damaged.
CHAPTER 10 Using CD-ROM Discs and Trays
How to Play Audio CDs
on Your Drive
YOUR TASK: Learn how to use your CD-R drive so that it can also
play audio CDs.
YOUR OBJECTIVE: Increase functionality of your drive. Provide musical
accompaniment for presentations. Goof off at work.
YOUR METHOD: You may choose from a variety of methods. You can
use anything from front panel controls or very basic,
bare bones audio CD software utilities to software
utilities that rival or surpass the capabilities of the CD
player attached to your stereo system.
1) The most basic method is to use the PlexWriter 8/20 front panel audio
controls. No special drivers are needed to operate this feature.
Once an AUDIO CD is inserted into the drive, simply push the button
to begin audio play. Once the audio is playing, push the play button
once for track advance, or hold down the button for more than 1
second to begin a fast forward search (ffwd). To eject, press the
Stop/Eject button once to stop audio play and a second time to eject
the CD.
2) Other alternatives include audio utilities designed into your operating
system (Media Player in Windows, for instance) or various other
utilities that can be purchased commercially.
3) Mac users can run a program such as CDT Remote (which is typically
included with FWBs CD-ROM device driver).
In order to hear the audio CD your drive is playing, you can plug a pair of
stereo headphones or self-powered speakers into the headphone jack on the
drives front panel. You can also connect your drive to an audio amplifier as
shown on page 39. The audio cables shown are available at most computer
and audio supply stores.
NOTE: The volume control on the front panel of your drive adjusts only the
sound level of the headphone jack. It has no impact on the volume
level of the rear panel audio outputs. Plextor Manager software can
CHAPTER 11
control volume level of the signal from the rear panel audio outputs.
Please refer to the Plextor Manager manual for information regarding
this function.
CHAPTER 11 How to Play Audio CDs on Your Drive
Stereo Mini-Plug
(To headphone jack)
Audio Amplifier
Audio Input
RCA-Type Plugs
(To audio out)
RCA-Type Plugs
Audio Amplifier
Audio Input
PX-R820Ti or PX-R820Te
PX-R820Te
CHAPTER 11 How to Play Audio CDs on Your Drive
Troubleshooting
YOUR TASK: Review some of the common problems you may
encounter when installing or operating your
PlexWriter drive.
YOUR OBJECTIVE: Gain a better understanding of how your drive
operates. Attempt to prevent problems before they
occur. Quickly fix many simple problems on your
own, rather than wait for assistance from a Plextor
representative.
YOUR METHOD: Read this entire section. Many of the problems
discussed happen only rarely. Many may seem as if
they do not pertain to you. If you are familiar with
the variety of problems that can occur, however, you
will be better prepared to deal with them if they
happen to you.
Guidelines
If you experience trouble with your PlexWriter drive, follow these guidelines:
PC Users:
1) Most SCSI interface boards can sense when a problem has occurred
and will generate an error message on your computer. Take note of
this message. Then, run the test (diagnostic) program that is probably
included with the device drivers for your SCSI interface board. Follow
the instructions given in the SCSI interface boards manual. If the
information provided by the error message and test program is not
sufficient for you to fix the problem, proceed to Step 2.
2) If your problem occurs during or immediately after the drives installation,
read Section 12.1PC Compatibles: Initial Installation. If your problem
occurs after you have run the drive successfully for an extended period,
read Section 12.2PC Compatibles: Existing Installations.
3) Attempt to match the problem you are having with the entries listed
beneath Symptoms. Then narrow your search by checking to see if
Additional Symptoms apply to you as well. Because different SCSI
interface boards generate differently worded error messages, the
messages displayed by your computer may differ from those shown
on the following pages.
CHAPTER 12
Upgrading Firmware
The PlexWriter 8/20 has the ability to upload new firmware to the drive.
Typically, Plextor creates new firmware revisions to meet the peculiar needs of
large computer manufacturers. It is rare that these will impact the performance
or operation of your drive. However, if you have proceeded through this chap-
ter with no result, you should check out our web site to learn about the latest
firmware.
Firmware upgrades can be found in either the Technical Support area or on the
Downloads page. There will be a description of the new firmware and its
intended use. Follow instructions for downloading, then simply run the
executable file on your system. The firmware upgrade will occur automatically.
Apple Computer Users:
Read Section 12.3Apple Macintosh
Technical Support
If you still cannot solve your problem after reviewing the relevant sections of
this chapter, visit the Technical Support and Frequently Asked Questions areas
of our web site.
NOTE: We encourage you to go to the Plextor web site (www.plextor.com)
before attempting to contact Technical Support. The answers to the most
common questions callers ask can be found quickly in the Frequently
Asked Questions area. Alink to the FAQ can be found on our home page.
If your problem persists, we ask you to try to isolate the problem before
contacting Technical Support. To do this, you should boot the system to DOS
from a floppy. The contents of this floppy may be available on our web site. If
you cannot locate the files on our web site, you will need to contact Technical
Support following the instructions in Chapter 13. They can help you locate the
files or send them to you via email.
Once you have created the floppy, insert it into the floppy drive and reboot
your system. At the prompt, type the drive letter for the CD-R drive (e.g. at the
A: prompt, type D:). If the drive is functional and you have a disc in the drive,
you should be able to see a list of directories and files on the CD (type DIR at
the prompt). If the CD-R drive is functioning properly, you can then focus on
the OS install or configuration of other equipment or software as likely
suspects.
CHAPTER 12 Troubleshooting
If after further sleuthing you cannot solve the issue, please contact Plextors
Technical Support Department (see Chapter 13).
12.1 PC Compatibles: Initial Installation
Symptoms Additional Symptom
No sound when running a No sound when playing an audio CD
program
Possible Causes and Solutions
Application Does Not Use CD-Audio
There are two types of audio you may encounter when using CD-ROMs:
1) Soundcard Audio:
This comes from data (e.g., .WAV or .MID files) that is transferred from
your CD-ROM disc via the SCSI host adapter into your computer and
is translated by your soundboard into sound. If you do not have a
soundboard or USB speakers, you will not be able to hear this form of
audio.
2) CD-Audio:
This comes from audio discs (like the ones used by your home stereo)
that are translated directly by your CD-R drive into sound. You do not
need a soundboard to hear this audio. You can hear this audio by
plugging a set of headphones or powered speakers into the
headphone jack on the front of your drive.
One reason, then, that you might not hear sound when playing a CD-ROM
disc is that a soundboard is required. These discs use only soundcard audio,
not CD-Audio.
To help you determine if you are having a soundboard problem or a CD-Audio
problem, try playing an audio CD in your CD-R drive. If you can hear music
(through headphones or speakers connected to the headphone jack on the
front of your drive), the CD-ROM disc you are playing may require the use of
a soundboard in order to hear sound. If possible, check the manual that came
with the CD-ROM disc and see if the use of a soundboard is recommended or
required.
If you have a soundboard and can hear an audio CD when it is played, but
cannot hear sound when you play a CD-ROM disc, you may have configured
your soundboard incorrectly. Check the troubleshooting section of your
soundboard manual for further advice. If you have a soundboard, but you
cannot hear an audio CD when it is played, check the following:
Improper/Missing Audio Cable
If you use a soundboard, you must connect the soundboard to your CD-R drive
with an audio cable. See page 32 to ensure you have properly installed this
audio cable. If you have a soundboard and CD-R drive but lack an audio cable,
contact one of the locations listed on page 59 for information on where to
purchase a cable.
Device Drivers Need to Be Updated
If you can hear an audio CD in your CD-R drive when it is in CD-Audio play
mode (see Chapter 11), but you cannot hear an audio CD with another music
CD utility (e.g., Animotions MCS CDMaster, CorelCD), your device drivers may
need to be updated. Contact your soundcard manufacturer for assistance.
Soundboard Volume Low
If when playing an audio CD, you do not hear sound even though everything
appears to be functioning normally (busy light on drive flickers, the time
counter on your audio CD utility is advancing), you may have the mixer
settings for your soundboard set too low. Each soundboard has different
settings for each input source, including one for CD-Audio. Run your
soundboards mixer program and verify that the volume is turned up.
Bad Soundboard Audio Cable
If you have verified that you have made the proper cable connections between
your drive and soundboard and you have the correct device drivers installed,
but you still do not hear sound when playing an audio CD, the problem may
rest with your audio cable. It may be defective and need to be replaced.
You can check to see if this is the case by doing the following:
1) Unplug the audio cable from the rear of your PlexWriter drive.
2) Plug a set of headphones or speakers that you know are good into the jack
on the front of the drive.
3) Try to play an audio CD. If you can now hear music, you may conclude that
you do, in fact, have a bad audio cable.
Symptoms
Cannot view PhotoCD discs
Can read only first session of a multisession disc
Receive error messages while reading PhotoCD images
Your PlexWriter drive is capable of reading Kodak PhotoCD multisession discs
if you use the appropriate device drivers and you run a PhotoCD viewing
program (e.g., Adaptec, Kodaks PhotoCD Access).
Device Drivers Need to Be Updated
If you purchased a SCSI card in a Plextor kit, contact Plextor Technical Support
for device driver information. If you purchased your SCSI card separately,
please contact the manufacturer of that card.
Bad PhotoCD Disc
If you can see a list of files from your PhotoCD (after issuing a DIR command),
but cannot read them, or experience errors while reading them, you may have
a bad PhotoCD disc. Try another PhotoCD disc. If it works, you should have
the defective disc replaced.
Invalid drive specification Error appears upon initial installation
No device found of the CD-R drive and device
No SCSI interface board found driver software
or no response from SCSI
interface board
No drives in use
Improper SCSI Device Driver Installation
Your computer needs a SCSI software device driver to link the SCSI interface
board to the CD-R drive. If this driver cannot be loaded properly, an error mes-
sage will normally be displayed on the screen.
Try rebooting the computer. Watch as the CONFIG.SYS file executes, and look
for an error message to appear. You can press the Control and S keys
simultaneously to freeze the display in order to read the error message (use the
Control and S combination again to continue).
If the SCSI device driver cannot be loaded properly, either a software or
hardware conflict exists. Software conflicts are generally caused by memory
managers; hardware conflicts by two peripherals vying for the same address
space. Please read the next two sections on Software and Hardware conflicts.
Software Conflict with Other Device Drivers
The SCSI interface board normally designates the device driver as the first
device driver loaded by the computer. When the computer has a memory
manager (e.g., HIMEM.SYS, 386MAX.SYS, or QEMM.SYS), in most cases the
memory manager is loaded first and the device driver loaded directly
thereafter.
If other device drivers are loading before the CD-ROM driver, place them after
the CD-ROM driver. If the memory manager tries to load the device driver into
high memory (e.g., DEVICEHIGH or LOADHIGH), disable the function so that
the driver is loaded into conventional memory.
Hardware Conflict Between the Interface Board and Your Computer
The SCSI interface board may be in conflict with another peripheral in your
computer. Normally, this conflict can be settled by selecting a different address
for the SCSI interface board. In some cases, you may wish to select a different
address for the conflicting peripheral.
If the driver still does not recognize the interface board, try the following:
1) Remove all non-essential peripherals from your computer (e.g.,
network boards, fax boards, etc.) and their device drivers from the
CONFIG.SYS and AUTOEXEC.BAT files.
2) Reboot the computer and ensure that the SCSI cards ASPI and
device driver recognizes the CD-R drive.
3) Turn OFF the computer and reinstall each peripheral and its device
drivers one at a time.
4) Repeat Steps 2 and 3 until the problem reoccurs. This means that the
problem is with the last peripheral you installed.
Improper MSCDEX Installation
The Microsoft CD-ROM extensions (filename: MSCDEX.EXE) or equivalent
files are required to run your CD-R drive under MS-DOS. If the SCSI driver was
successfully loaded, check for proper installation of MSCDEX.EXE by
rebooting the computer and watching the AUTOEXEC.BAT file as it executes
for an error message.
SCSI Interface Board Not Properly Seated
If the SCSI interface board is not fully seated into the computers expansion
slot, the device driver software will not recognize it. Inspect the interface
board where it seats into the connector on your computers motherboard.
There should not be more than a small gap between the interface board and
the connector.
Symptom
Incorrect DOS version
Conflict Between MS-DOS 5.0 and Microsofts CD-ROM Extensions Version
2.2 (or Lower)
MS-DOS 5.0 users should use Microsofts CD-ROM Extensions (filename
MSCDEX.EXE) Version 2.25. If you do not have either of these versions and
plan to use DOS 5.0 with MSCDEX.EXE Ver 2.2 (or lower), you can resolve this
conflict by doing the following
1) Type the following line into your CONFIG.SYS file:
DEVICE=C:\DOS\SETVER.EXE
2) Switch to the DOS prompt.
3) Type the following:
SETVER MSCDEX.EXE 4.01
Then press the Enter key.
4) Reboot your computer.
Conflict Between MS-DOS 6.0 and Microsofts CD-ROM Extensions (file-
name: MSCDEX.EXE) Version 2.21 (or Lower)
MSCDEX.EXE Ver. 2.22 (or higher, preferably ver. 2.25) must be used with
DOS 6.0. Use of an earlier version will result in an Incorrect DOS Version
message. A copy of MSCDEX.EXE ver. 2.25 is included with DOS 6.0. You can
find this file in your C:\DOS directory.
If you previously had loaded MSCDEX.EXE ver. 2.21 (or lower), your computer
might still be recognizing this lower version rather than 2.22 (or higher).
To correct this problem, you must edit your AUTOEXEC.BAT file using a text
editor or word processor. Your AUTOEXEC.BAT file will probably contain a
line that may look something like this:
C:\TSCSI\MSCDEX.EXE /D:TSLCD /M:10
In this example, C:\TSCI is the path to MSCDEX.EXE. The path name will vary
depending on the type of SCSI device driver software you use. The D:TSLCD
refers to the device.
Change only the path of this line in your AUTOEXEC.BAT file so that it finds
the updated MSCDEX.EXE file in your DOS directory. This line should be
edited to read:
C:\DOS\MSCDEX.EXE /D:PLEX0001 /M:10
in DOS. Save the AUTOEXEC.BAT file and reboot your computer.
In Windows 3.1, the AUTOEXEC.BAT file would read:
C:\WINDOWS\COMMAND\MSCDEX.EXE/D:PLEX0001/M:10
and the CONFIG.SYS file would look something like this:
DEVICE=C:\SCSI\ASPI8DOS.SYS
(ASPI Manager for AHA2940 controller)
DEVICE=C:\SCSI\ASPICD.SYS /D:DEVICE_NAME
(ASPI Manager CD-ROM driver)
or
When using the Plextor driver (PLEXTOR.SYS) instead of ASPICD.SYS:
DEVICE=C:\PROGRA~1\PLEXTOR\PLEXTOR.SYS /D:DEVICE_NAME
(ASPI Manager CD-ROM driver)
No device found Driver fails to recognize the SCSI
No SCSI interface board found interface board
or no response from SCSI
interface board
Possible Cause and Solution
Drive Not Resetting
In some cases, even if you restart the computer by pressing its reset button or
the Control, Alt, and Delete keys simultaneously, the drive does not appear to
respond. Try turning the power switches on the drive and computer OFF, then
ON. This complete shutdown should fully reset the drive and computer.
Symptom Additional Symptom
CDR101 Not Ready All commands sent to the drive
Reading Drive [X] result in CDR101 error
Defective CD-ROM or CD-R Disc
A fingerprint, contaminants, or deep scratches on the discs surface may
prevent the drive from reading or writing data. Read Chapter 10 to learn how
to handle and clean discs.
You should also review the low performance symptom discussed on page 53.
Bad Connection Between the CD-R Drive and the SCSI Interface Board
Inspect the cable, drive, and interface board for recessed, broken, or bent pins.
If a ribbon cable is used, inspect for any signs of distress, such as kinking.
Ensure the red stripe side of the ribbon cable plugs into Pin 1 on both the drive
and the interface board.
Audio CD Disc in the Drive
Plextor CD-R drives are capable of playing high-quality audio when used with
appropriate audio playback software, or when the drive is set to Audio CD
play mode (see Chapter 11). Since audio compact discs do not have computer
data, typing computer commands while a CD-Audio disc is in your drive will
result in an error message.
12.2 PC Compatibles: Existing Installations
Invalid drive specification Interface board driver fails to
No device found recognize the CD-R drive
Drive not responding
Drive Is Not On
If you have a PlexWriter external drive, check that its front-panel power switch
is ON. If the drive is the internal model, ensure the power cord from your
computers power supply is plugged firmly into the drive power connector.
Power is applied correctly if one of the front panel LEDs are on.
Ensure the red stripe side of the ribbon cable plugs into Pin 1 on both the drive
and the interface board.
Improper SCSI Bus Termination
Ensure that only the peripheral at the end of the internal SCSI cable and/or the
last peripheral in a daisy chain of external devices is terminated (see Chapter
7). Some peripherals have a setting marked Termination Power instead of
Terminator. Ensure that termination power switches are set correctly.
CDR101Not Ready CD-R drive responds to directory
Reading Drive [X] (DIR) command but cannot run a
program
Improper SCSI Bus Termination
Ensure that only the last peripheral on the SCSI bus is terminated (see Chapter
7). Some peripherals have a setting marked Termination Power instead of
Terminator. Ensure that termination power switches are set correctly.
Defective CD-ROM/CD-R Disc
Fingerprints, contaminants, or deep scratches on the discs surface may
Conflict with a Network Card
Temporarily remove the network card and all related drivers. Reboot the com-
puter and check that the SCSI controller and the CD-RW drive are recognized.
CDR101Not Ready Errors occur intermittently
Reading Drive [X]
Drive Not Terminated
If your CD-ROM drive is the only SCSI peripheral attached to your computer
or is the last SCSI peripheral in a daisy chain (i.e., a cable connecting multiple
SCSI peripherals to a single SCSI interface board), check that its termination
switch is ON. Always turn the drive power OFF before changing the setting of
the rear panel switches (see Chapter 7).
CDR101Not Ready All commands sent to the drive
Reading Drive [X] result in CDR101 error
Audio CD Disc in the Drive
Plextor CD-ROM drives are capable of playing high-quality audio when used
with appropriate audio playback software or when the drive is set to Audio CD
play mode (see Chapter 11). Since audio compact discs do not have computer
data, typing standard data commands when a CD-Audio disc is in the drive
will result in an error message.
Inspect the cable, drive, and interface card for recessed, broken, or bent pins.
CDR103Not High Occurs with certain discs only
Sierra Format
Incorrect Disc
The disc might be intended for another type of computer, such as a Macintosh
or Sun, or it is not mastered in the High Sierra or ISO 9660 formats.
CDR103Not High Occurs regardless of the discs used
Sierra Format
Incorrect Jumper Setting
You might have the block jumper set to ON. (If you have an internal drive, see
page 13. If you have an external drive, see page 16).
Hardware Conflict
If the SCSI interface board uses DMA channels, try changing the selected DMA
channel. See the instruction manual for your SCSI interface board.
Memory Manager Conflict
If the SCSI interface board uses memory-mapped addressing or has a BIOS,
exclude the addresses from the memory manager. See your SCSI interface
board instruction manual.
Incorrect Version of Microsoft CD-ROM Extensions
Version 2.00 or higher of MSCDEX is required to read a High Sierra or ISO
9660 format disc.
Excessive noise CDR101 error message
Disc heard jumping
Excessive vibration
prevent the drive from reading data. See Chapter 10 to learn how to handle
and clean discs.
You should also review the low performance symptom discussed on the next
page.
CD-R Drive Set to Test Mode
Turn this switch OFF. The test mode is for factory use only. Always turn the
drive power OFF before changing the setting of the switches (see Chapter 6).
CD-ROM/CD-R Disc is Poorly Balanced
Poorly manufactured discs that are out-of-balance or discs with poorly
distributed ink on labeling will cause significant vibration at high speeds. Read
errors may also occur. Such out-of-balance conditions can also exist if the disc
label adds more weight to one area of the disc than another. Adhesive labels
may also cause out-of-balance conditions. Remove any adhesive labels on the
label side of the disc and clean the surface following instructions in Chapter
10. If there is no foreign substance on the disc, you may wish to contact the
disc manufacturer for a replacement.
In DOS or Windows (3.x, 95, 98, NT), use Plextor Manager to lower the drive
speed.
Symptom
Low performance of CD-ROM application software
Drive Automatically Set to Slower Throughput
Plextors drives are designed to automatically switch from top speed
throughput to slower speeds when they encounter a defect or a scratch on
your disc. The drive will then continue to read data from the disc at the
auto-selected speed for a period of time. If no read errors are encountered,
then the drive spins up to the top speed possible without read errors. It is also
possible that the disc is dirty. Please refer to Chapter 10 for instructions on how
to clean your CD-ROM disc.
Symptoms
Disc is ejected after being inserted
ON/BUSY light flashes 4 times
CD Is Unreadable
Plextors drives are designed to automatically eject any unreadable CD. Please
be sure that the CD-ROM/CD-R disc or audio CD is label-side up in the tray.
If not, this will cause the drive to eject the CD. An incorrectly written CD-R
disc, or a damaged, scratched, or otherwise unreadable CD will cause this
same symptom. Inserting a known good disc will correct this problem.
12.3 Apple Macintosh
Symptoms
Invalid drive specification
No device found
Drive not responding
SCSI Address Conflicts with the Hard Disk Drive
This usually can be corrected by selecting another SCSI address (normally
addresses 1 to 6) for your CD-R drive.
NOTE: The Macintoshs hard disk uses address 0 and its internal SCSI adapter
uses address 7.
Bad connection between CD-R drive and SCSI interface
Check cable for bent pins.
Symptom
Computer does not respond
INIT Conflicts
Remove all INITs except those absolutely needed from your System Folder and
the ones copied from the CD-ROM device driver disk. If the CD-R drive
functions correctly, reinstall the INITs one at a time, restarting the Macintosh
after each one until the problem is solved.
Symptom
Low performance of CD-ROM application software
System Set for Virtual Memory
If your Macintosh is using System 7 and is in Virtual Mode, it may exhibit slow
performance during real-time graphics and animation. This is because your
hard disk drive and CD-R drive must use your computers SCSI bus almost
simultaneously. To remedy this, remove Virtual Mode from the system and
restart the Macintosh.
Contacting Plextors
Technical Support
Department
YOUR TASK: Learn the variety of methods you can use to contact
Plextors Technical Support Department. Learn what
information you should gather before contacting
Plextors Technical Support Department.
YOUR OBJECTIVE: Know how to get in contact with Plextor if you
experience any problems installing or operating
your PlexWriter 8/20 CD-R drive.
YOUR METHOD: Store Plextors email, web site, phone, and fax
numbers in a convenient location. Keep your drives
serial number and a copy of your sales receipt handy
as well.
If you experience a problem while installing or operating your PlexWriter 8/20
drive, please refer first to the relevant sections of this manual regarding setup
and installation (Chapters 69). If you do not uncover the solution there,
please refer next to the Troubleshooting chapter in this manual (Chapter 12). It
contains solutions to the most common types of problems fielded by our
technical support staff. You may also wish to refer to the Frequently Asked
Questions (FAQ) section of our web site to assist you in troubleshooting the
problem on your own.
NOTE: We encourage you to go to the Plextor web site (www.plextor.com)
before attempting to contact Technical Support. The answers to the most
common questions callers ask can be found quickly in the FAQ area. A
link to the FAQ can be found on our home page.
If you have not been successful in your quest, our Technical Support
Department will help you solve problems that relate specifically to your
PlexWriter8/20 drive. In many cases, a problem that appears to be caused by
your CD-R drive actually originates in another part of your computer. In such
instances, our technical support staff will try to help you identify the part (e.g.,
SCSI interface board) at fault and will refer you to the manufacturer of that part
for further assistance.
Although we think highly of the capabilities of our technical support staff, we
recognize that they do suffer from some limitations; namely, they do not
CHAPTER 13
possess psychic or telepathic powers. Therefore, their ability to help you
depends a great deal on your ability to help them. You must act as their eyes
and ears as they try to diagnose and fix your problem. If you gather the infor-
mation requested below before you contact them, you will find that your prob-
lem can be resolved much more quickly.
How to Contact Us
There are three ways for you to contact Plextors Technical Support
Department:
1) Send us email at support@plextor.com or visit our web site for
answers to Frequently Asked Questions.
2) Send a fax to the attention of the Technical Support Department at
408-986-1010. Include your telephone number and the hours during
which you can be reached. Be as detailed as possible in describing
your problem. It typically is useful if you also send a printout of your
AUTOEXEC.BAT and CONFIG.SYS files if you are running
DOS/Windows 3.x operating system.
3) Call 800-886-3935 and select the technical support extension.
Before You email/Log On/FAX/Call
Knowledge is power (or so some say). Empower our technical support folks
with information. This will save both you and them time and possible
frustration. Please gather as much of the following information as possible
before contacting us.
7 The serial number and TLA number of your CD-R drive. Your serial
number can be found both on the warranty card that accompanied the
drive and on a label on the drive itself. The TLA number appears both
on the drive label and on a sticker at the rear of internal drives.
7 The version of Plextor Manager you are using, if applicable.
7 The latest version of firmware you loaded onto the drive, if applicable.
7 The name and model number of your SCSI interface board (e.g.,
Adaptec AHA-2940, Advansys ABP-930UA).
7 The version of the software device drivers, if any, that came with your
SCSI interface board (this typically is found on the label of the floppy
disk which contains the device drivers).
7 The version of the Windows, DOS, Mac, Novell, OS/2, or UNIX
operating system you are using.
CHAPTER 13 Contacting Plextors Technical Support Department
7 The brand name and model number of your computer (e.g., Dell
466/NP, Micron P66PCI Powerstation, ALR Evolution V, Apple
Macintosh, Performa 575).
7 The type of VGA, Super VGA, or other graphics card you use.
7 Brand name and model number of any other peripherals you have
installed/connected to your computer (e.g., CD-ROM, scanner, fax
board, network board).
Returns
You must receive an RMA (Returned Materials Authorization) number from our
Technical Support Department before any Plextor CD-R drive can be returned
for repair or replacement. Any drive sent to Plextor without an RMA number
will not be accepted. Drives must be sent postage prepaid. We recommend
that you insure your shipment, as Plextor cannot be held responsible for any
damage that may occur during shipment.
Helpful Contacts
COMPANY PHONE FAX BBS, Web, and/or
Product email address
Adaptec 408-945-8600 408-262-2533
SCSI interface boards & CD-R software www.adaptec.com
Advansys 800-525-7443 408-383-9612 408-383-9540
SCSI interface boards www.advansys.com
AMC 800-390-9328 425-861-8391
Devices, cables & accessories cust.svc@amcdirect.com
Bason Comp. 800-238-4453 818-727-9064 818-597-0275
SCSI interface boards www.bowin.com
CeQuadrat 800-330-6734 650-843-3799
CD-R software www.cequadrat.com
Creative Labs 405-742-6600 405-742-6633 405-742-6660
Soundboards www.creativelabs.com
Creative Digital Research 408-255-0999 408-255-1011
Windows UNIX software for CD-R www.cdr.com
Diamond 800-468-5846 408-325-7408 408-524-9301
Soundboards www.diamondmm.com
DPT 407-830-5522 407-260-5366 407-830-1070
SCSI interface boards www.dpt.com
DTC 408-474-0868 408-474-0828 408-546-5671
SCSI interface boards www.datatechnology.com
FWB 650-482-4800 650-482-4858
Mac device drivers www.fwb.com
Pacific Inter Connects 408-654-0234 408-982-9329
Audio cables www.piccable.com
Plextor 408-980-1838 408-986-1010 408-986-1569
Recommend SCSI boards, audio cables,
and all other technical support needs support@plextor.com
Testa CD Labs 520-531-1880
CD-Tach Performance Benchmarks http://tcdlabs.simplenet.com
Specifications
PX-R820Ti/e Internal/External
Disc
Useable Formats CD-DA; CD-ROM (Mode 1); CD-ROM (Mixed Mode);
Read and Write CD-ROM & CD-DA; CD-ROM XA; Mode 2 Form 1 and Form 2;
Mode 2 Mixed Form, CD-I; Photo CD; CD-EXTRA
Disc Type ISO 9660-HFS; Rockridge; PhotoCD, Video CD; CD-I; CD-Extra
(CD-Plus); Enhanced CD; CD-R; CD+G; CD-Midi
Disc Diameter 12cm (60 min. & 74 min.)
Writing Modes Track-at-Once, Disc-at-Once, Multisession, Fixed and Variable
Packet Writing
Recommended Taiyo Yuden, TDK, Ricoh, Mitsui, Kodak, Fuji, Hitachi, Sony,
Media Imation, Philips
Performance
Data Transfer Rate CLV Write/CAV Read
Sustained Read/Write 20X (read only): 3.0MB/sec Outer track
12X (read only): 1.8MB/sec
8X (read only): 1.2MB/sec
4X (read/write): 600KB/sec
Burst Read/Write 10MB/sec (synchronous)
(Fast SCSI) 4MB/sec Burst (asynchronous)
Average Random 170ms
Access
Data Buffer 4MB
Spindle Motor Brushless
Error Rate Mode 1: Block/10
12
Bits; Mode 2: Block/10
9
Bits
CHAPTER 14
Front Panel
Eject Auto Eject; Manual Emergency Eject
Lights DISC IN; ON/BUSY; Write; L.H.
Disc Loading Auto
Headphone Jack Stereo Minijack, 0.8V at 32 Ohms
Volume Control Wheel Knob
CD-Audio Controls Play/Track Advance; Stop/Eject
Rear Panel
Power Supply Internal: DC +5V at Average 0.78A (peak 0.93A);
DC +12V at Average 0.7A (peak 1.2A)
External: AC 100-240V 50/60 Hz, 0.3A (Auto Switching)
Power Switch External: Tumbler Type; 3A, 250V
Interface Connector Internal: SCSI Bus, 50-Pin Flat Ribbon Type
External: SCSI Bus, Two (2) 50-Pin High Density
Termination Internal: Jumper Switch
External: DIP Switch
Audio Output Internal: Stereo Analog Output, Molex Connector (L*G*G*R),
MPC3 Standard
External: Stereo Analog Output, RCA Jacks
Jumper Switches Internal: SCSI ID, Parity, Term, Test, Block Size, Eject
DIP Switch External: Parity, Term, Test, Block Size, Media Lock
Rotary Switch External: SCSI ID
Environmental Conditions
Operating
Temperature 5 to 40 degrees Celsius
Humidity 20% to 80% Noncondensing
Storage
Temperature 30 to 55 degrees Celsius
Humidity 20% to 95% Noncondensing
Dimensions and Weight
Dimensions (W/H/D) Internal: 5.78" x 1.64" x 7.95" (without front panel)
External: 7.0" x 2.24" x 12.03" (without projection)
Weight Internal: 2.5 lbs
External: 5.8 lbs.
Reliability
MTBF 60,000 POH
Tray Loading 30,000 Load Cycles
CHAPTER 14 Specifications
Windows 95/98
Installation Guide
Quick Install
Windows 95/98 should automatically recognize and support your SCSI
controller and Plextor CD-R drive. Microsoft has included a generic CD-ROM
device driver in the operating system. This driver also supports the PlexWriter
as a reader. They have also included numerous controller specific drivers on
the Windows 95/98 CD-ROM. If you connect your Plextor drive to a
previously installed and operating SCSI controller, Windows 95/98 will
recognize it automatically. You will need to install third party software to use
the PlexWriter as a recorder. If you purchased your SCSI controller in a Plextor
kit, you can use either the Windows 95/98 CD or the Plextor Manager disc to
provide the necessary file, when applicable. If you purchased your new SCSI
controller from another source, you must use the Windows 95/98 CD. If
Windows 95/98 does not have the necessary file, you will need to use software
provided by the manufacturer of the SCSI controller. If you encounter any
problems, we suggest you read the following detailed instructions.
Instructions and Background
If the Quick Install description above does not work, this section will tell you
a little about the Windows 95/98 operating system, help you figure out what
your current system configuration is, and then walk you through the
installation. If you are lucky, this process will be close to Plug and Play.
Either way, dont worry. You will soon be using the highest performance CD-R
drive around. If you have any problems at all, our technical support staff will
help you.
Microsoft has incorporated Plug and Play software into Windows 95/98.
Theoretically, this enables true Plug and Play peripherals, such as your Plextor
CD-R drive, to configure themselves automatically after installation. You have
been hearing about Plug and Play for a long time now. The unfortunate thing
is that even now things are not quite as automatic as they should be. Thats all
right though Plextor will make it work for you.
For a true Plug and Play experience while installing a SCSI peripheral, many
things are required. Your system must have Plug and Play BIOS available either
on the motherboard or on a Peripheral Component Interconnect (PCI) SCSI
controller. All PCI controllers have this capability. Your controller itself must
also have its own Plug and Play capabilities. Again, all PCI controllers include
APPENDIX
these features. Your SCSI controller must also be SCAM capable. It may sound
like a con game, but actually SCAM stands for SCSI Configured Auto Magically
(sure it sounds hokey, but we didnt make it up). Others may refer to it as SCSI
Configured AutoMatically.
Any combination of up to seven internal and external devices can be attached
to a single SCSI controller. Each must be set to a unique ID number (06) for
identification purposes in your computer system. SCAM is the Plug and Play
feature that overrides whatever a devices SCSI ID is set to (physically, via
jumpers or switches on the back of the drive) and makes sure each device has
a unique ID.
Your computers capabilities are pretty much out of our control. On the other
hand, your Plextor drive is fully SCAM capable. Benevolent folks that we are,
if you bought a Plextor kit you also have a SCAM capable SCSI controller in
front of you wouldnt make much sense to sell you a true Plug and Play
drive and some old technology controller board, would it? You can also buy
SCAM capable controller kits off the shelf at most computer stores now. It is
possible that you have a PCI SCSI controller, which means you are in really
good shape, especially if you have already installed Windows 95/98.
So, lets say your computer is Plug and Play or you have a PCI SCSI controller,
your SCSI controller and Plextor CD-R drive are SCAM capable, and you have
successfully installed Windows 95/98. No problem, right? Wrong. In Windows
95/98, various files are used to support different SCSI controllers (think of them
as device drivers). Unfortunately, different files are used in a SCAM environment
than are used in a non-SCAM environment. To make matters worse, some
Windows 95/98 releases will not recognize when your controller is SCAM
capable and load the correct file. Instead, since SCAM was not a requirement
for logo certification by the time Windows 95/98 was released, and most
devices were not yet capable, it automatically loads the files that support the
non-SCAM device.
As you might suspect by now, Plextor fixes this problem for you. Just pay close
attention to the instructions and everything will work out fine. Now that we
have bored you with the history and current state of Plug and Play, its time to
get that great new CD-R drive up and running. Turn the page and lets get you
started.
APPENDIX Windows 95/98 Installation Guide
Configuration Identification
The first thing you want to do is figure out exactly what your configuration is
and what you are trying to accomplish. Review the following descriptions and
then go to the appropriate section of this manual.
1) You have purchased a new SCAM capable Plextor CD-R drive kit with
a SCAM capable SCSI controller. If you purchased the drive without a
SCSI controller, it is also possible that you already had, or separately
purchased, a SCAM capable SCSI controller board, your computer
has a Plug and Play BIOS, or your SCSI controller is of the PCI variety.
You have Windows 95/98 installed. You may have purchased a new
computer with Windows 95/98 installed, or you purchased an
upgrade to Windows 95/98 on floppies and already installed it. You
may also have upgraded to Windows 95/98 from a CD using an older
CD-ROM drive. If this scenario describes your situation, consider
yourself a state-of-the-art computer jockey. Go to the section titled
Plug and Play Installation (page 65).
2) You have a SCAM capable controller, as in the Plug and Play
configuration, but your computer is a little older and does not have a
Plug and Play BIOS. You also do not have a PCI class SCSI controller
to provide Plug and Play BIOS. Go to the section titled Non-Plug and
Play Installation (page 68).
3) You did not buy a Plextor kit and have an older SCSI board that is not
SCAM capable. Go to the section titled Non-SCAM Installation
(page 71).
4) You are currently running DOS or Windows 3.x and have purchased
an upgrade to Windows 95/98 on CD-ROM. Since you do not have
an old CD-ROM drive, you need to install your new Plextor CD-R
drive first. But you need to run the upgrade while in a DOS/Windows
environment, and you need a device driver. Problem? Not with
Plextor. We provide all the software you need to run under
DOS/Windows and upgrade to Windows 95/98. Its a bit complex,
but well get you there. Go to the section titled Upgrading to
Windows 95/98 From DOS/Windows Using CD-ROM (page 73).
By the way, our instructions generally assume you are installing a SCSI
controller as well as a Plextor CD-R drive. Of course, it is quite possible you
already have a SCSI controller installed and operating under Windows 95/98. If
so, you can make appropriate adjustments to the procedures. For instance, since
your controller is already functioning under Windows 95/98, it will not ask for
a disk or CD to get support for the controller. We have addressed some potential
problems this may cause in the troubleshooting portion of each section.
Plug and Play Installation
Install Hardware
You should be able to simply install your SCSI controller, CD-ROM drive, and
all cabling without any concern for things like SCSI ID selection. First, turn
OFF your computer system, then review Chapter 8. You should also familiarize
yourself with Chapter 7: Termination. However, the quick solution here is to
place your internal drive at one end of the SCSI ribbon cable and the SCSI
controller at the other end of the cable. Your drive ships from the factory with
termination enabled, so everything should be fine. If you put another SCSI
device between the controller and the drive, you need to make sure
termination is disabled on that device. For external devices, if your Plextor
drive is the last in a chain of devices, leave termination enabled. If it is not last
in the chain, disable termination. All SCAM capable boards should have the
ability to automatically set termination of the board itself, so you should not
have to deal with this. Once your hardware is plugged in, it is time to play. But
first, we have to take care of that little device driver problem.
Install Software
After your CD-ROM drive and SCSI controller are installed, it is time to make
the right software file available to complete your Plug and Play environment.
Turn on your computer, and your system should automatically detect and
configure your SCSI controller. When you start Windows 95/98, it will then
recognize that it does not have the right driver available for your new SCSI
controller. A dialog box named New Hardware Found appears, followed
immediately by a dialog box named Insert Disk. At this point, click OK in the
Insert Disk dialog box and a second New Hardware Found dialog box will
appear. It will ask you to insert the Windows 95/98 disk or CD. DONT DO IT.
If you do put in your Microsoft disk or CD, Windows 95/98 may automatically
load the non-SCAM capable file for the SCSI controller we provided.
Instead, if you purchased a Plextor kit with SCSI controller, insert the Plextor
Manager disk. This disk has the SCAM capable support file for your SCSI
controller to complete your Plug and Play CD-ROM environment. After
inserting the disk, select Browse in the dialog box and then select the
appropriate drive letter. The Windows 95/98 configuration process should
select the correct file from the disk and copy it to the correct Windows 95/98
subdirectory on your hard drive.
If you purchased a SCAM capable SCSI controller separately, the correct file
should be located on a disk provided with the controller. We suggest you try
using this disk (supplied by the manufacturer of your SCSI controller) rather
than inserting the Windows 95/98 disk. If you do not have this disk (or cannot
find it among all the other disks you have), you can try using the files provided
by Windows 95/98, but we cannot guarantee you will get SCAM support.
Reboot Your Computer
Reboot your machine by selecting Shut Down from the Start Button. In the shut
down dialog box, select Restart the Computer and select Yes. This will reboot
your computer with the new configuration. As your system goes through all its
self checks, you might find it interesting to watch the display and note the SCSI
ID that has been assigned to your CD-R drive. Your drive came from the
factory physically set to ID 4. It is possible (especially if you have other SCSI
devices) that once you reboot your computer, the configuration process will
reassign the drive to some other SCSI ID number. If so, you have just seen
visual proof of Plextors SCAM capabilities. Get out your favorite or most
useful CD and enjoy or install premastering software and write your own.
Troubleshooting
If you followed the previous instructions, you should be up and running
without any problems. If things are not working correctly, there are four likely
problems.
1) You might have overlooked our instructions to use the Plextor
Manager to get the necessary driver support for your SCSI controller.
If you used the Windows 95/98 disk or CD, the configuration process
may have copied the wrong (i.e., non-SCAM capable) driver support.
Then, if some other SCSI device attached to your SCSI controller is
physically set to the same ID as your CD-R drive, a conflict will occur.
To solve this problem, insert the Plextor Manager or use Windows
Explorer or the following DOS command to copy the correct file to
the applicable Windows 95/98 subdirectory:
COPY D:\*.MPD C:\WINDOWS\SYSTEM\IOSUBSYS
Reboot again and everything should work fine.
2) The second likely cause is that your motherboard may not have a
Plug and Play capable BIOS and your Plug and Play SCSI controller
is not of the PCI variety. You will need to turn off your computer and
disable the Plug and Play capabilities on your SCSI controller. Review
the controllers documentation (check the Quick Start Guide or
similar document first) to determine the location of the disable
switch. After disabling, review the Install Hardware portion of the
Non-Plug and Play Installation section of this manual (page 68). Make
sure termination is set properly on your controller and all devices
attached to it. Restart your computer.
3) It is also possible that the SCSI controller you may have purchased
separately is not really SCAM capable. Not to worry, though. You
simply need to deal with SCSI ID selection. First turn off your
computer. Review the discussion of SCSI ID selection (Chapter 6) and
then check the physical selection of SCSI ID on your CD-R drive and
any other SCSI devices connected to your controller. Make sure that
all devices are physically set to unique IDs. Since your board is not
SCAM capable, it will probably not have automatic termination. You
will also need to make sure the termination of your board is set
properly. If you have both internal and external devices attached, the
termination on your controller should be disabled. Review the
controllers documentation to determine how to do this. If you have
only internal devices, or only external devices, termination of your
SCSI controller should remain enabled. After your IDs and
termination are set properly, restart your system.
4) It is possible that your previously or separately purchased SCAM
capable controller is not being supported properly by Windows
95/98. If you had to use the Windows 95/98 disk or CD to get support
for the controller, it may not have existed, or it may have loaded a
non-SCAM capable version of the file. If the file did not exist, you will
have to contact the SCSI controller manufacturer to obtain the
necessary file (you might first look through your own stack of disks
one more time). Once you have the correct file, you can then use the
Windows 95/98 Add New Hardware Wizard to load it. If Windows
95/98 did load a file during the configuration process, and you have
another SCSI device besides your Plextor CD-R drive, then you prob-
ably have a conflict with your SCSI IDs. In other words, Windows
95/98 loaded a non-SCAM capable support file. The quick fix here is
to leap out of the Plug and Play environment and reset the SCSI ID on
one of your devices per the previous paragraph. Alternatively, you
can find or obtain the SCAM capable file from the manufacturer of
your SCSI controller. You will then need to copy that file to a
Windows 95/98 subdirectory using Windows Explorer or the following
DOS command:
COPY D:\FILENAME.EXT C:\WINDOWS\SYSTEM\IOSUBSYS
The SCSI controller documentation should tell you which file to copy.
If not, you should contact the technical support department of the
SCSI controller manufacturer. If you cannot reach them, or they
cannot help you, contact Plextors Technical Support Department.
5) Finally, if you still suspect the CD-R drive as the source of the problem,
you should boot the system to DOS from a floppy. The contents for
this floppy may be available on Plextors web site. If you do not locate
the files on our web site, contact Technical Support by following the
instructions in Chapter 13. They can help you locate the files or send
them to you via email.
NOTE: We encourage you to visit our Plextor web site (www.plextor.com)
before attempting to contact Technical Support. The answers to
the most common questions callers ask can be found quickly in
the Frequently Asked Questions area. A link to the FAQ can be
found on our home page.
Once you have created the floppy, insert it into the floppy drive and
reboot your system. At the prompt, type the drive letter for the CD-ROM
drive (e.g. at the A: prompt, type D:). If the drive is functional and you
have a disc in the drive, you should be able to see a list of directories
and files on the CD (type DIR at the prompt). If the CD-R drive is func-
tioning properly, you can then focus on the OS install or configuration
of other equipment or software as likely suspects.
Non-Plug and Play Installation
Install Hardware
Refer to the Operation Manual for instructions on installing your SCSI
controller, cabling, and CD-R drive. If your non-PCI controller has Plug and
Play features, but your computer system is not supporting Plug and Play, you
will need to disable the Plug and Play capabilities on your SCSI controller.
Review the controllers documentation (check the Quick Start Guide or similar
document first) to determine the location of the disable switch.
You might want to familiarize yourself with the chapter on termination.
However, the quick solution here is to place your internal drive at one end of
the SCSI ribbon cable and the SCSI controller at the other end of the cable.
Your CD-R drive ships from the factory with termination enabled, so
everything should be fine. If you put another SCSI device between the
controller and the drive, you need to make sure termination is disabled on that
device. For external devices, if your drive is the last in a chain of devices, leave
termination enabled. If it is not last in the chain, disable termination.
Install Software
After your CD-ROM drive and SCSI controller are installed, it is time to make
the right software device driver file available to support your new controller.
Turn on your computer and start up Windows 95/98. Your system should
automatically detect and configure your SCSI controller. If you have just
installed it, Windows 95/98 will then recognize that it does not have the right
driver available. A dialog box named New Hardware Found appears, followed
immediately by a dialog box named Insert Disk. At this point, click on OK in
the Insert Disk dialog box and a second New Hardware Found dialog box will
appear. It will ask you to insert the Windows 95/98 disk or CD. Please, DONT
DO IT. If you do put in your Microsoft disk or CD, Windows 95/98 will
automatically load the non-SCAM capable file for the SCSI controller we
provided.
Instead, if you purchased a Plextor kit with SCSI controller, insert the Plextor
Manager disc. This disc has the SCAM capable support file for your SCSI
controller to complete your Plug and Play environment. After inserting the
disc, select Browse in the dialog box and then select the appropriate drive
letter (probably A:\). The Windows 95/98 configuration process should select
the correct file off the disc and copy it to the correct Windows 95/98
subdirectory on your hard drive.
If you purchased a SCAM capable SCSI controller separately, the correct file is
hopefully located on a disk provided with the controller. We suggest you try
using this disk supplied by the manufacturer of your SCSI controller rather than
inserting the Windows 95/98 disk. If you do not have this disk (or cannot find
it among all the other disks you have), you can try using the files provided by
Windows 95/98, but we cannot guarantee you will get SCAM support.
Reboot your machine by selecting Shut Down from the Start button. Select
Restart the Computer and select Yes. This will reboot your computer with the
new configuration.
Troubleshooting
If you followed the previous instructions, you should be up and running without
any problems. If things are not working correctly, there are four likely problems.
1) If you purchased a Plextor kit, you might have overlooked our
instructions to use the Plextor Manager disc to get the necessary
driver support for your SCSI controller. If you used the Windows
95/98 disk or CD, the configuration process may have copied the
wrong (i.e., non-SCAM capable) driver support. Then, if some other
SCSI device attached to your SCSI controller is physically set to the
same ID as your PlexWriter, a conflict will occur. To solve this
problem, insert the Plextor Manager disc and use Windows Explorer
or the following DOS command to copy the correct file to the
applicable Windows 95/98 subdirectory:
COPY D:\*.MPD C:\WINDOWS\SYSTEM\IOSUBSYS
Reboot again and everything should work fine.
2) The second likely cause is that you neglected to disable the Plug and
Play capabilities on your SCSI controller. Turn off your computer.
Review the controllers documentation (check the Quick Start Guide
or similar document first) to determine the location of the disable
switch.
3) It is also possible that the SCSI controller you purchased separately is
not really SCAM capable. Not to worry, though. You simply need to
deal with SCSI ID selection. First, turn off your computer. Review the
discussion of SCSI ID selection (Chapter 6) and then check the
physical selection of SCSI IDs on your drive and any other SCSI
devices connected to your controller. Make sure that all devices are
physically set to unique IDs. Since your board is not SCAM capable,
it will probably not have automatic termination. You will also need to
make sure the termination of your board is set properly. After your IDs
and termination are set properly, restart your system.
4) Finally, it is possible that your previously or separately purchased
SCAM capable controller is not being supported properly by
Windows 95/98. If you used the Windows 95/98 disk or CD to get
support for the controller, it may not have existed, or it may have
loaded a non-SCAM capable version of the file. If the file did not
exist, you will have to contact the SCSI controller manufacturer to
obtain the necessary file (you might first look through your own stack
of disks one more time). Once you have the correct file, you can then
use the Windows 95/98 Add New Hardware Wizard to load it. If
Windows 95/98 did load a file during the configuration process, and
you have another SCSI device besides your Plextor drive, then you
probably have a conflict with your SCSI IDs. In other words,
Windows 95/98 loaded a non-SCAM capable support file. The quick
fix here is to leap out of the Plug and Play environment and reset the
SCSI ID on one of your devices per the previous paragraph.
Alternatively, you can find or obtain the SCAM capable file from the
manufacturer of your SCSI controller. You will then need to copy that
file to a Windows 95/98 subdirectory using Windows Explorer or the
following DOS command:
COPYA:\FILENAME.EXT C:\WINDOWS\SYSTEM\IOSUBSYS
The SCSI controller documentation should tell you which file to copy.
If not, you should contact the Technical Support department of the
SCSI controller manufacturer. If you cannot reach them, or they
cannot help you, contact Plextors Technical Support Department.
Non-SCAM Installation
Install Hardware
Refer to Chapter 8 for instructions on installing your SCSI controller, cabling,
and CD-ROM drive. If your non-PCI controller has Plug and Play features, but
your computer system is not supporting Plug and Play, you will need to disable
the Plug and Play capabilities on your SCSI controller. Review the controllers
documentation (check the Quick Start Guide or similar document first) to
determine the location of the disable switch.
Since your SCSI board is not Plug and Play and SCAM capable, you will have
to ensure that all peripheral devices attached to the controller have unique
SCSI IDs (see Chapter 6). Make sure that all peripheral SCSI devices connect-
ed to the controller board are physically set to unique ID numbers (using
switches or jumpers).
You should familiarize yourself with Chapter 7: Termination. However, the
quick solution here is to place your internal drive at one end of the SCSI ribbon
cable and the SCSI controller at the other end of the cable. Your CD-R drive
ships from the factory with termination enabled, so everything should be fine.
If you put another SCSI device between the controller and the drive, you need
to make sure termination is disabled on that device. For external devices, if
your drive is the last in a chain of devices, leave termination enabled. If it is
not last in the chain, disable termination.
Finally, controllers that are not SCAM capable will not likely have automatic
termination. You will need to make sure termination of your controller is set
properly. If you have both internal and external devices attached, the
termination on your controller should be disabled. Review the controllers
documentation to determine how to do this. If you have only internal devices,
or only external devices, termination of your SCSI controller should remain
enabled.
Install Software
After your drive and SCSI controller are installed, it is time to make the right
software device driver files available to support your new controller. Turn on
your computer and start up Windows 95/98. Your system should automatically
detect and configure your SCSI controller. If you have just installed a new
controller, Windows 95/98 will recognize that it does not have the right driver
available. A dialog box named New Hardware Found appears, followed
immediately by a dialog box named Insert Disk. At this point, click on OK in
the Insert Disk dialog box and a second New Hardware Found dialog box will
appear. It will ask you to insert the Windows 95/98 disk or CD. If you do this,
it will automatically load the non-SCAM capable file.
Since your SCSI controller does not support SCAM, this is appropriate. After
inserting the disk or CD, select Browse in the dialog box and then select the
appropriate drive letter. The Windows 95/98 configuration process should
select the correct file off the floppy disk and copy it to the correct Windows
95/98 subdirectory on your hard drive.
It is possible that Windows 95/98 will not have the required support for your
SCSI controller. If that is the case, you will need to call the controller
manufacturers technical support department. If you still have problems, call
Plextors Technical Support Department at 800-886-3935.
Restart the computer and select Yes. This will reboot your computer with the
new configuration.
Troubleshooting
If you followed the previous instructions, you should be up and running without
any problems. If things are not working correctly, there are three likely problems:
1) You might have inadvertently copied the SCSI controller support files
on the Plextor Manager disk into your Windows subdirectory. It is
possible the SCAM files on our disk are not properly supporting your
controller. To solve this problem, delete the applicable *.MPD file(s)
from C:\Windows\System\Iosubsys and then reinstall the correct
support file using the Windows 95/98 Add New Hardware Wizard.
(See Add New Hardware, page 76, in the Upgrading to Windows
95/98 from DOS/Windows Using CD-ROM section.) Restart your
system and everything should work fine.
2) The second likely cause is that your previously purchased SCSI
controller supports some Plug and Play features, but it is not PCI and
is not SCAM capable, and you also have no Plug and Play BIOS on
your motherboard. You will need to disable Plug and Play on your
controller. Turn off your computer. Review the controllers
documentation (check the Quick Start Guide or similar document
first) to determine the location of the disable switch. Double-check for
proper termination. Restart your computer.
3) Finally, you may have failed to set a unique SCSI ID for each of your
peripheral devices connected to your controller. Turn off your
computer. Review SCSI ID selection (Chapter 6) and then check the
physical selection of SCSI IDs on your CD-ROM drive and any other
SCSI devices connected to your controller. Make sure that all devices
are physically set to unique IDs. After your IDs are set properly, restart
your system.
Upgrading to Windows 95/98
From DOS/Windows Using CD-ROM
Install Hardware
If you are installing your Plextor drive in a Plug and Play environment (Plug
and Play BIOS on the motherboard and a SCAM capable controller), refer to
Install Hardware in the Plug and Play Installation section on page 65.
If you are installing your Plextor drive in a non-Plug and Play environment (no
Plug and Play BIOS on the motherboard, and your interface card is not PCI but
is SCAM capable), refer to Install Hardware in the Non-Plug and Play
Installation section on page 68.
If you are installing your Plextor drive in a non-SCAM capable environment
(your SCSI controller is not SCAM capable), refer to Install Hardware in the
Non-SCAM Installation section on page 71.
Install Software
In order to use your Plextor drive under DOS or Windows 3.x to upgrade to
Windows 95, you must have a device driver to support it. If you just installed
a new SCSI controller that you did not purchase from us, you also need to load
what is called an ASPI Manager for your controller. Refer to your controllers
documentation for instructions. If you purchased our kit, the ASPI Manager
will load as part of our CD-R device driver installation process. If you
purchased our kit, or successfully loaded the ASPI Manager, you are ready to
go. Insert the Plextor Manager disk into your floppy drive. Then enter the
following DOS command to install the Plextor device driver:
A:\INSTALL
Or, from your Program Manager in Windows, choose File and Run, and enter
the following on the command line:
A:\INSTALL
Install Windows 95/98
Insert your Windows 95/98 CD into your new Plextor CD-R drive and follow
Microsofts instructions for upgrading. During the installation process,
Windows 95/98 will attempt to find and install support for your SCSI
controller, resulting in the following scenarios:
Separately Purchased SCSI Controller
If you have a previously purchased and installed SCSI controller that
is supported by Windows 95/98, support will be loaded automatically.
If your previously purchased SCSI controller is not supported by
Windows 95/98, you will be prompted to insert a disk that includes
the appropriate file. That disk should have been provided with the
controller.
If you have a separately purchased SCSI board installed, we cannot guarantee
support will be available on Windows 95/98. After the upgrade finishes, you
can check to see if Windows recognizes your SCSI controller by selecting My
Computer. If a CD-ROM drive icon is shown in this Window, everything
should be functioning properly. If not, then support for your SCSI controller did
not load properly (Windows 95/98 cant look through your controller to see
your drive). Select Control Panel and then double-click the Add New
Hardware icon and follow the instructions. This process will take some time,
but hopefully will find the files necessary to support your SCSI board. If not, it
is possible that Windows 95/98 does not have the necessary file available, or
that non-SCAM capable support was loaded even though you purchased a
SCAM capable controller. You may need to contact the manufacturer of the
SCSI controller to get the correct file. It is also possible that your older
controller simply does not have support available for Windows 95/98 and will
need to be replaced.
Plextor Provided SCSI Controller
If the SCSI controller provided by Plextor is not supported by Windows
95/98, you will be prompted to insert a disk that includes the
appropriate file. At this point, you can insert the Plextor Manager disk,
point Windows 95/98 to the root directory, and it will automatically
select and install the proper file.
If your Plextor provided SCSI controller is supported by Windows
95/98, it will automatically install non-SCAM capable 32-bit support
for your SCSI board. If your SCSI controller was not SCAM capable,
this would present no problem. However, since you purchased a
SCAM capable Plextor kit, you may experience problems. After the
installation is complete, copy the *. MPD file(s) from the Plextor disc
to the correct Windows 95/98 subdirectory using Windows Explorer or
the following DOS command:
COPY A:*.MPD C:\WINDOWS\SYSTEM\IOSUBSYS
The non-SCAM capable file originally installed will be overwritten.
Disable Plextor Manager
Our preliminary tests indicate that Plextors device driver will operate your
Plextor drive under Windows 95/98. However, our device driver is written in
16-bit code and has not been fully tested under Windows 95/98. In addition,
all the utilities (and more) available in 16-bit code Plextor Manager are also
available in 32-bit code Plextor Manager. Therefore, we recommend that you
disable the driver. If you choose to operate your Plextor drive under Windows
95/98 using the Plextor device driver and subsequently encounter any
problems, your first step should be to disable the driver. To disable Plextors
DOS/Windows driver, click on the Start button. From the pop-up menu, select
Run. Type NOTEPAD C:\CONFIG.SYS. This allows you to edit the
CONFIG.SYS file using the notepad editor. Find the lines that refer to the ASPI
Manager (example: BTDOSM.SYS or ASPI4DOS.SYS) and device driver called
PLEXTOR.SYS. Type REM in front of each of those two lines. This disables
these lines by marking them as Remarks. Select Save from the File menu, and
then Exit.
Restart the computer and then select Yes. This will reboot your computer with
the new configuration.
When Windows 95/98 starts, an icon for a CD-R drive will appear in My
Computer. If it does not, then the support for your SCSI controller has probably
not loaded correctly. Go to the following section, Add New Hardware. Even
if you get the CD-ROM icon, you may want to check that the Windows 95/98
32-bit driver is working properly. Select Control Panel in My Computer and
double-click on System. Click on the tab called Device Manager at the top of
the window. In the new window of devices, double-click on SCSI Controllers.
This displays all the SCSI controllers currently installed in your system. In the
box called Driver Status, the message should be This Device Is Working
Properly. If you get this message, you can now make full use of your CD-R
drive with the Windows 95/98 32-bit support.
Add New Hardware
If your SCSI controller is not recognized by Windows 95/98 after installation,
or if the message under Driver Status does not indicate that it is working
properly, you can use the Windows 95/98 Add Hardware Wizard in an attempt
to load the required support. Access My Computer, open Control Panel, then
double-click on the Add New Hardware icon and follow the directions. This
will look for and auto-install Windows 95/98 support for your SCSI board and
CD-R drive, if available. At the end of this process, a screen will notify you if
the SCSI board has been detected. If no new devices are detected, your SCSI
board is probably not supported by Windows 95/98 directly. You may be able
to get support from the manufacturer of the SCSI controller by calling their
technical support department.
About Plextor
Plextor is a subsidiary of the Shinano Kenshi Company (SKC), Ltd. SKCs roots
stretch back to 1918, when it began to manufacture textiles in Japans northern
prefecture of Nagano. (Nagano, incidentally, was the site of the 1998 Winter
Olympics.) SKCs involvement in the electronics industry started in 1962,
when it diversified into the production of stepper motors for commercial audio
products. SKC is now one of the worlds largest manufacturers of small motors
used in hard disks, floppy disks, tape drives, copy machines, video cameras,
and your Plextor CD-R drive.
Over the past decade, SKC has developed a reputation as an innovator in
compact disc and CD-ROM technology. In 1992, it was the second company
to begin shipments of double speed CD-ROM drives. In 1994, it was the first
company to begin shipments of half-height quad speed CD-ROM drives. In
early 1995, SKC was the first company to ship a six speed CD-ROM drive. In
early 1996, they shipped the first professional-quality eight speed CD-ROM
drive. Many award winning drives followed. The PlexWriter you now own
represents the highest achievement from the CD-ROM technology leader. SKC
is also a leading manufacturer of compact disc players used for industrial and
commercial applications (e.g., background music players for retail stores,
restaurants, and shopping centers).
Plextor acts as SKCs sales, service, and support arm throughout the world. In
addition to CD-ROM drives, Plextor also sells under its own label professional
audio equipment used by radio stations, high-speed printing presses, talking
books for the sight impaired, and a CD encoding system developed by SKC
that can pack up to eight hours of audio onto a single compact disc.
Plextor has offices in Asia, the Americas, and Europe. Plextor first opened an
office in Californias Silicon Valley in 1990. Rapid growth has required it to
move twice since then to larger offices. Plextor now occupies a 30,000 sq. ft.
facility in Santa Clara, California, which is staffed by sales, marketing,
technical support, engineering, administrative, and shipping personnel. Our
Japanese office opened in 1985. Our European office (in Brussels) began oper-
ation in 1994.
Plextor CD-ROM Drives
Data Access Buffer
Model Introduced Transfer Rate Time Size
1st generation DM-3020/5020 1990 150KB/sec 430ms 64K
2nd generation DM-3021/5021 1991 150KB/sec 340ms 64K
3rd generation DM-3024/5024 1992 300KB/sec 265ms 64K
4th generation DM-3028/5028 1993 335KB/sec 240ms 64K
5th generation PX-43CH/45CH 1994 600KB/sec 220ms 1MB
6th generation PX-43CS/45CS 1994 600KB/sec 170ms 256K
8th generation PX-43CE/45CE 1995 675KB/sec 130ms 256K
10th generation PX-12CS/12TS 1996 1.8MB/sec 105ms 512K
11th generation PX-20TS 1997 1.83.0MB/sec 85ms 512K
12th generation PX-32CS/PX-32TS 1997 28MB/sec 85ms 512K
13th generation PX-40TS/TSUW 1998 2.6-6.0 MB/sec 85ms 512K
Plextor CD-R Drives
Max
Record Max Data Access Buffer
Model Introduced Speed Transfer Time Size
1st generation PX-R24CS 1996 2X 300KB/sec 390ms 512K
2nd generation PX-R412CS 1997 4X 600KB/sec 190ms 2MB
3rd generation PX-R820T 1998 8X 1.2MB/sec 170ms 4MB
Warranty Information
PLEXTOR CORP. (PLEXTOR) warrants your PlexWriter 8/20 against any defect in
material and workmanship, under normal use, for a period of one year following its date
of purchase. In the event this product is found to be defective within the warranty
period, PLEXTOR will, at its option, repair or replace the defective unit.
This warranty is void if: a) the unit is operated or stored under abnormal use and
maintenance conditions; b) if the unit is repaired, modified, or altered, unless such
repair, modification or alteration is expressly authorized in writing by PLEXTOR; c) if the
unit is subject to abuse, neglect, lightning strike, electrical fault, improper packaging, or
accident; d) if the unit is installed improperly; or e) if the serial number of the unit is
defaced or missing.
PLEXTOR will not, under any circumstances, be liable for direct, special, or consequential
damages such as, but not limited to, damage or loss of property or equipment, loss of profits
or revenues, cost of replacement goods, or expense or inconvenience caused by service
interruptions. Under no circumstances will any person be entitled to any sum greater than
the purchase price paid for the unit.
To obtain warranty service, you must contact PLEXTORs Technical Support Department
by calling 800-886-3935. They will attempt to diagnose and correct your problem by
phone. If the unit does not function properly, they will issue a Return Material
Authorization (RMA) number. You may be asked to furnish proof of purchase to confirm
that the unit is still under warranty.
All drives returned to PLEXTOR must be securely packaged and shipped postage
prepaid. All product returns must be authorized in advance by PLEXTORs Technical
Support Department. Authorization is confirmed by issuance of the RMA number,
which must be written prominently on the outside of the box in which the defective unit
is returned to PLEXTOR.
PLEXTOR (U.S.A.)
4255 Burton Drive, Santa Clara, CA 95054
Web Site: www.plextor.com
email: support@plextor.com
Phone: 408-980-1838
FAX: 408-986-1010 BBS: 408-986-1569
Toll Free: 800-886-3935
PLEXTOR (Japan)
8F Kyodo-building 1-4-21 Yaesu
Chuou-ku, Tokyo, Japan 103
Web Site: www.plextor.co.jp
Phone: 81-3-3517-8061 FAX: 81-3-3517-8065
PLEXTOR (Europe)
Excelsiorlaan 1, 1930 Zaventem, Belgium
Web Site: www.plextor.be
Phone: 32-2-725-5522 FAX: 32-2-725-9495

Plextor Plexwriter 820 Manual

Uploaded by

Copyright:

Available Formats

Plextor Plexwriter 820 Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Plextor Plexwriter 820 Manual

Uploaded by

Copyright:

Available Formats

Operation Manual

Model PX-R820Ti Internal and PX-R820Te External

You might also like