Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 92 views

    Sikadur - 31: 2-Part Thixotropic Epoxy Adhesive

    Uploaded by

    camelia_pirjan5776
    Sikadur-31 is a two-part, thixotropic epoxy adhesive and repair mortar used for bonding or filling gaps between construction materials. It has high strength and adhesion without the need for primers on most surfaces. Sikadur-31 has good chemical resistance and can be applied in layers up to 30mm thick. It is solvent-free, cures without shrinkage, and remains flexible with low creep under load.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Sikadur - 31: 2-Part Thixotropic Epoxy Adhesive

    Uploaded by

    camelia_pirjan5776
    92 views4 pages
    Sikadur-31 is a two-part, thixotropic epoxy adhesive and repair mortar used for bonding or filling gaps between construction materials. It has high strength and adhesion without the need for primers on most surfaces. Sikadur-31 has good chemical resistance and can be applied in layers up to 30mm thick. It is solvent-free, cures without shrinkage, and remains flexible with low creep under load.

    Original Description:

    sikadur-31

    Original Title

    sikadur-31

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Sikadur-31 is a two-part, thixotropic epoxy adhesive and repair mortar used for bonding or filling gaps between construction materials. It has high strength and adhesion without the need for primers on most surfaces. Sikadur-31 has good chemical resistance and can be applied in layers up to 30mm thick. It is solvent-free, cures without shrinkage, and remains flexible with low creep under load.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    92 views4 pages

    Sikadur - 31: 2-Part Thixotropic Epoxy Adhesive

    Uploaded by

    camelia_pirjan5776
    Sikadur-31 is a two-part, thixotropic epoxy adhesive and repair mortar used for bonding or filling gaps between construction materials. It has high strength and adhesion without the need for primers on most surfaces. Sikadur-31 has good chemical resistance and can be applied in layers up to 30mm thick. It is solvent-free, cures without shrinkage, and remains flexible with low creep under load.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    Product Data Sheet Edition 17/08/2007 Identification no: 02 04 02 03 001 0 000000 Sikadur-31

    Sikadur-31
    2-part thixotropic epoxy adhesive
    Product Description
    Uses Sikadur-31 is a solvent-free, moisture tolerant, thixotropic, two part structural adhesive and repair mortar, based on epoxy resins and special fillers, designed for use at temperatures between +10C and +40C. As a structural adhesive for: Concrete elements Hard natural stone Ceramics, fibre cement Mortar, Bricks, Blocks, Masonry etc. Steel, Iron, Aluminium Wood Polyester, Epoxy Glass As a fast setting repair mortar for: Corners and edges Hole and void filling Joint arrises Joint filling and crack sealing: Rigid joint filling Crack filling and sealing (non moving) Characteristics / Advantages Sikadur-31 has the following advantages: Easy to mix and apply Suitable for dry and damp concrete surfaces Very good adhesion to most construction materials High strength adhesive Thixotropic: non-sag and suitable for vertical and overhead application Solvent free Hardens without shrinkage Different coloured components (for mixing control) No primer needed High initial and ultimate strengths Good abrasion resistance Adhesive and filler in one Impermeable to liquids and water vapour Good chemical resistance

    Construction

    Sikadur-31

    1/4

    Tests
    Approval / Standards Conforms to ASTM C 881-78, Type I, Grade 3, Class B+C.

    Product Data
    Form
    Colours Part A: Part B: Part A+B mixed: white black concrete grey

    Packaging

    3 kg (A+B) Pre-batched unit Part A: 2.00 kg plastic container Part B: 1.00 kg plastic container

    Storage
    Storage Conditions / Shelf-Life 12 months from date of production if stored properly in original unopened, sealed and undamaged packaging in dry conditions at temperatures between +5C and +40C. Protect from direct sun light.

    Technical Data
    Chemical Base Density Sag Flow Epoxy resin. 1.85 kg/l (Part A+B mixed) (at +27C) On vertical surfaces it is non-sag up to 10 mm thickness. (According to FIP 5.3 with measurement according to ASTM D2730) Layer Thickness 30 mm max. When using multiple units, one after the other. Do not mix the following unit until the previous one has been used in order to avoid a reduction in handling time. Change of Volume Shrinkage / Creep: Hardens without shrinkage.

    Mechanical / Physical Properties


    Compressive Strength
    Curing time 1 day 7 days 14 days

    (According to IS 9162-1979)
    +30C ~30 N/mm ~65 N/mm ~70 N/mm
    2 2 2

    Bond Strength
    Curing time 7 days Temperature +30C

    (According to ASTM C 882)


    Substrate Concrete dry Bond strength > 11 N/mm
    2*

    *100% concrete failure.

    Sikadur-31

    2/4

    System Information
    Application Details
    Substrate Quality Mortar and concrete must be older than 28 days (depends on minimal requirement of strengths). Verify the substrate strength (concrete, masonry, natural stone). The substrate surface (all types) must be clean, dry and free from contaminants such as dirt, oil, grease, existing surface treatments and coatings etc.. Steel substrates must be de-rusted similar to Sa 2.5. The substrate must be sound and all loose particles must be removed. Substrate Preparation Concrete, mortar, stone, bricks: Substrates must be sound, dry, clean and free from laitance, ice, standing water, grease, oils, old surface treatments or coatings and all loose or friable particles must be removed to achieve a laitance and contaminant free, open textured surface. Steel: Must be cleaned and prepared thoroughly to an acceptable quality i.e. by blast cleaning and vacuum. Avoid dew point conditions. Other surfaces (polyester, epoxy, glass, ceramic): On these substrates pre-apply Sikafloorr -156 (primer) and then, wet on wet apply Sikadur -31.

    Application Conditions / Limitations


    Substrate Temperature Ambient Temperature Material Temperature Substrate Moisture Content Dew Point +10C min. / +40C max. +10C min. / +40C max.
    Sikadur -31 must be at a temperature of between +10C and +40C.

    When applied to mat moisture concrete, brush the adhesive well into substrate. Beware of condensation! Substrate temperature during application must be at least 3C above dew point.

    Application Instructions
    Mixing Mixing Time Part A : Part B = 2 : 1 (by weight) Pre-batched units: Mix parts A+B together for at least 3 minutes with a mixing spindle attached to a slow speed electric drill (max. 600 rpm) until the material becomes smooth in consistency and a uniform grey colour. Avoid aeration while mixing. Then, pour the whole mix into a clean container and stir again for approx. 1 more minute at low speed to keep air entrapment at a minimum. Mix only that quantity which can be used within its potlife. When using a thin layer adhesive, apply the mixed adhesive to the prepared surface with a spatula, trowel, notched trowel, (or with hands protected by gloves). When applying as a repair mortar use some formwork. When using for bonding metal profiles onto vertical surfaces ,support and press uniformly using props for at least 12 hours, depending on the thickness applied (not more than 5 mm) and the room temperature. Once hardened check the adhesion by tapping with a hammer. Cleaning of Tools
    Clean all tools and application equipment with Sika Colma Cleaner immediately after use. Hardened / cured material can only be mechanically removed.

    Application Method / Tools

    Sikadur-31

    3/4

    Potlife

    100 g mass +30C

    (According to FIP 5.1 and 5.2) ~30

    The potlife begins when the resin and hardener are mixed. It is shorter at high temperatures and longer at low temperatures. The greater the quantity mixed, the shorter the potlife. To obtain longer workability at high temperatures, the mixed adhesive may be divided into portions. Another method is to chill parts A+B before mixing them (not below +5C).

    Value Base Health and Safety Information

    All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control. For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Material Safety Data Sheet containing physical, ecological, toxicological and other safety-related data. The information, and, in particular, the recommendations relating to the application and end-use of Sika products, are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sikas recommendations. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The user of the product must test the products suitability for the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

    Construction

    Legal Notes

    Sika India Pvt. Ltd. Commercial Complex II 620, Diamond Harbour Road Kolkata, 700 034, India

    Phone +91 33 2447 2448/2449 Telefax +91 33 2468 8688/2665 www. sika.in info@in.sika.com

    Sikadur-31

    4/4

    You might also like