2009 TSFX Physics U3
2009 TSFX Physics U3
2009 TSFX Physics U3
Detailed Studies 1. Einsteins Special Relativity OR 2. Further Electronics OR 3. Structures and Materials 13 13 13 13 13 13 26 26 26 Total 90
p: 03 9663 3311
f: 03 9663 3939
e: admin@tsfx.com.au
w: www.tsfx.com.au
p: 03 9663 3311
f: 03 9663 3939
e: admin@tsfx.com.au
w: www.tsfx.com.au
direction: 3 marks
The volleyball is struck by a person with an impulse on the ball of 13.5 Ns upwards. QUESTION 2 If the duration of the impact was 0.25 s, what was the average force of the person on the ball?
direction: 3 marks
QUESTION 3 With what velocity does the ball leave the person?
m/s
direction: 3 marks
Page 1
QUESTION 4 Which one of the following is the worst representation of Newtons First Law; the Law of inertia? A. An object maintains its state of motion unless acted on by an unbalanced force. B. An object maintains its velocity unless acted on by an unbalanced force. C. An object maintains its speed unless acted on by an unbalanced force. D. An object maintains its momentum unless acted on by an unbalanced force. E. An object maintains its inertia unless acted on by an unbalanced force. 2 marks
Questions 5 and 6 refer to the following information: A small 24 g stone is placed on a fast moving circular turntable at a point 8 cm from the centre, as illustrated in Figure 1. It is moving with a speed of 50 m/s. stone 8 cm
Figure 1 QUESTION 5 What is the magnitude of the frictional force holding the stone in its motion?
2 marks
QUESTION 6 The speed of the turntable is increased fairly rapidly and the stone (st) leaves its circular path. Which of the arrows A - D in Figure 2 indicates the most likely path of the stone as it leaves the turntable, as viewed from above?
direction of rotation
st
A
Figure 2
C D
2 marks
Page 2
QUESTION 7 Andrew, Betty and Charles are discussing the size of the earths gravitational field at an altitude equal to the earths radius (RE), as illustrated in Figure 3. Andrew says that the gravitational field strength due to the Earth at this point will be 2.45 N/kg. Betty argues that it will be 4.9 N/kg and Charles is very confident that g = 9.8 N/kg at this altitude. Explain who is correct and why?
RE RE
Figure 3
Questions 8 to 10 refer to the following information: In attempting to jump from one ramp to another a skater moving at 4.8 m/s attempts to clear a gap of 2.0 metres. The take-off angle is of 28 elevation. For questions 8 & 9 assume air resistance is negligible.
Figure 4
Page 3
QUESTION 8 After leaving the first ramp, what time does it take for the skater to reach the highest point in his flight?
s 3 marks QUESTION 9 Does the skater land on the other ramp? Show your calculations and reasoning.
3 marks QUESTION 10 When positioned as in Figure 4, which of the vectors (A D) represents the direction of the net force acting on the skater at this time? (Air resistance must be included for consideration).
B C
2 marks
Page 4
Questions 11 to 13 refer to the following information: The Asteroid Research Spacecraft (ARS) has been launched and will orbit the asteroid Skradgit whose mass is very much less than that of earth. QUESTION 11 Which one of the statements A to D best describes how the period of the spacecraft in orbit around Skradgit would compare with the period of an Earth satellite with the same orbital radius? A. B. C. D. The period around the asteroid would be greater than for the Earth satellite. The period around the asteroid would be less than for the Earth satellite. The period would be the same. There is insufficient information to decide.
2 marks
m/s
3 marks
Page 5
Questions 14 to 15 refer to the following information: A dog (mass = 14 kg) runs in a northerly direction across a beach with a speed of 3.0 m/s and turns to run to the west at 3.0 m/s. QUESTION 14 What is the magnitude and direction of the change of velocity of the dog?
m/s
direction: 2 marks
QUESTION 15 What is the magnitude and direction of the impulse on the dog due to the sand?
kgm/s
direction:
2 marks
Page 6
G1 W
12 V
G3 Y
G4
X G2
Figure 1 QUESTION 1 Determine the total resistance for the circuit in Figure 1.
3 marks
2 marks
Page 7
QUESTION 3 Which globe(s) will glow the brightest? Explain your answer. Globe:
2 marks QUESTION 5 At which point (W, X, Y, Z) would you place an ammeter to confirm your answer to Question 2? A. B. C. D. W X Y Z
2 marks
Page 8
Questions 6 to 9 refer to the following information: Jo and Peter are designing a circuit to function as a thermostat. Their circuit will consist of a thermistor, an LED and a variable voltage supply, Vs, as shown in Figure 2.
Figure 2
The characteristic curves for the thermistor and the LED are shown in Figures 3 and 4 respectively.
3.0
120 100
Resistance (kOhm)
2.5 2.0
Current (mA)
0 10 20 30 40
80 60 40 20 0
Figure 3
0.5
1.5
2.5
Figure 4
Page 9
QUESTION 6 Determine the resistance of the thermistor in when the temperature is 20oC.
1 mark
1 mark QUESTION 8 V
Jo and Peter would like the LED to produce enough light for a photodiode to switch on a heater when the temperature is below 20oC. The LED will glow brightly enough when the current is 10mA. QUESTION 8 Determine the supply voltage required for the LED to indicate when the temperature is 20oC.
2 marks V
QUESTION 9 Will Jo and Peters circuit work as they intended? Provide reasons for your answer.
Page 10
Questions 10 to 13 refer to the following information: A state of the art audio system is to be set up in the music classroom. The system will be wired using optical cabling. The block diagram in Figure 5 shows the arrangement of the devices and the electrical components enabling the signal from a microphone to be sent to and amplified for a set of speakers.
Figure 5 QUESTION 10 Which of the following components (A-D) shows where light intensity modulation occurs in the system described in Figure 5? Modulation A. B. C. D. Microphone LED Photodiode Amplifier 1
V(out) (V)
V(in) (V)
Figure 6
Page 11
2 marks
V(in) (V)
Time(ms)
QUESTION 13 On the axes below, sketch the corresponding output voltage of amplifier 2. Clearly label the vertical axis.
0.25
0.2
0.15
0.1
0.05
0 0 1 2 3 4 5 6 7
Time(ms)
3 marks
Page 12
QUESTION 14 The photodiode receiving the light signal from the optical fibres has the following I-V curve.
Figure 8 What is the photocurrent produced by the photodiode when a light intensity of 4.0 Wm-2 is produced by the optical cables? A 1 mark
Page 13
QUESTION 2 Galileos postulate implies that: A. B. C. D. a stationary observer will observe all inertial frames the same. all inertial frames of reference are unique. all velocities are relative to the observer. time passes at different rates that depend on the speed of the observer.
2 marks
Page 14
The following information refers to Questions 3 to 5: Imagine a train of proper length 100 m passing through a station at half the speed of light. There are two lightning strikes, one at the front and one at the rear of the train, leaving scorch marks on both the train and the station platform. Observer X is standing on the station platform midway between the two strikes, while observer Y is sitting in the middle of the train. Light from each strike travels to both observers.
0.5 c
QUESTION 3 If observer X on the station concludes from his observations that the two lightning strikes occurred simultaneously, what would observer Y on the train see? A. B. C. D. Observer Y would observe Bolt A first. Observer Y would observe both Bolts at the same time. Observer Y would observe Bolt B first. Observer Y is going so fast no bolts of lightning will be observed.
2 marks
QUESTION 4 What will be the distance between the scorch marks on the train, according to X? A. B. C. D. 76 87m 100m 115m
2 marks
Page 15
QUESTION 5 What will be the distance between the scorch marks on the platform, according to Y? A. B. C. D. 76 87m 100m 115m
2 marks
QUESTION 6 George is moving with uniform velocity of 0.9c relative to Wendy. They are each wearing a wristwatch with a second hand that takes one minute to make one complete revolution. When George observes the second hand on his watch to have made one complete revolution, how many revolutions will Wendy observe the second hand of her watch to have made? A. B. C. D. 0.43 0.9 1.0 2.3 2 marks
QUESTION 7 Muons have a half-life of 3.1 x 10-6 s as measured in a reference frame in which the muons are at rest. Suppose an accelerator creates a pulse of muons moving with a speed of 0.9c. How far will the pulse have travelled as measured by a laboratory observer when half the muons in the pulse will have decayed? (c = 3.0 x 108 ms-1) A. B. C. D. 835 930 1920 2130
2 marks
Page 16
The following information refers to Questions 8 and 9: When electrons are accelerated through a potential difference of 1.50 106 V, they attain a speed of 0.97c relative to the laboratory. The rest mass of an electron is 9.1 x 10-31 kg. QUESTION 8 Determine the mass of the electron at this speed. A. B. C. D. 9.1 x 10-31 kg 9.4 x 10-30 kg 3.7 x 10-30 kg 3.9 x 10-30 kg 2 marks
QUESTION 9 Determine its kinetic energy at this speed. A. B. C. D. 1.02 x 10-13J 1.56 x 10-13J 2.51 x 10-13J 3.36 x 10-13J 2 marks
QUESTION 10
Relativistic momentum is: A. B. C. D. equal to the internal change in an objects motion. dependent on the relativistic mass and velocity of the object. dependent only to an objects relative mass. a fixed quantity related to the rest conditions of the object.
2 marks
Page 17
QUESTION 11 In the Michelson-Morley experiment an interferometer is used in which a beam of light is split into two beams. These travel along different paths and are then recombined and interfere and so form interference fringes. The diagram below shows the main features of such an interferometer.
What did the results of the experiment indicate? A. B. C. D. No detectable velocity difference from light reflecting off each mirror. Speed of light is affected by the speed of the light source. A changing interference fringe pattern was observed when the interferometer is rotated. At difference times of the year the Earth travels in different directions.
2 marks
Page 18
The following information refers to Questions 12 and 13: Suppose that some time in the future it will be possible for astronauts to travel to a distant star system 8.4 light years away, at a constant speed of 0.95c. QUESTION 12 How many years would it take for the astronauts to get there as measured by observers in the Earths frame of reference? A. B. C. D. 8.84 years 8.4 years 2.8 years 1.4 years 2 marks
QUESTION 13 On arrival at the star system they immediately set out on the return journey, at the same speed. On their arrival back on Earth how many years have passed, since the astronauts first left Earth, as measured by the astronauts? A. B. C. D. 2.8 years 5.6 years 16.8 years 17.7 years
2 marks
Page 19
Figure 1 When switch S1 closes the 100F capacitor charges. After a period of time in which the capacitor has fully charged, S1 opens and S2 closes causing the capacitor to discharge through resistor A. QUESTION 1 What is the time constant for the charging of the capacitor? A. B. C. D. 10 ms 20 ms 100 ms 200ms 2 marks
Page 20
The graph in Figure 2 represents the discharge characteristics of the capacitor when switch S2 closes.
Figure 2 QUESTION 2 The value of resistor A is best represented by: A. B. C. D. 100 200 500 1000 2 marks
Page 21
The following information applies to Questions 3 and 4: In the circuit in Figure 3, a resistor is connected to an AC power supply through a single power diode. Leads of a cathode ray oscilloscope are connected to each side of the resistor at points A and B.
Figure 3 The following graphs in Figure 4 represent a range of possible displays on the screen of the cathode ray oscilloscope.
Figure 4
Page 22
QUESTION 3 Which graph best represents the display on the cathode ray oscilloscope? A. B. C. D. E. F. Graph A Graph B Graph C Graph D Graph E Graph F
2 marks
QUESTION 4 The connections to the cathode ray oscilloscope are now moved to positions C and D.
Which graph best represents the time varying voltage that is likely to be viewed on the screen? A. B. C. D. E. F. Graph A Graph B Graph C Graph D Graph E Graph F
2 marks
Page 23
QUESTION 5 The circuit in Figure 5 is a voltage divider power supply that can be used to provide a DC voltage (V OUT) to a LOAD.
Figure 5 Select the alternative which best describes this circuit. A. B. C. D. A regulated power supply because it can provide a DC voltage to the load at a value less than the supply voltage. A regulated power supply because it can provide a constant DC voltage to a load. An unregulated power supply because if the load resistance changes the value of V OUT also changes. An unregulated power supply because the supply to the voltage divider is DC.
2 marks
Page 24
QUESTION 6 The circuits in Figure 6 are attempts by a student to develop a full-wave rectified voltage supply to a resistor.
Figure 6 Choose the alternative that best indicates the full selection of successful circuits. A. B. C. D. E. F. G. H. Circuit A only Circuit B only Circuit C only Circuit D only Circuits B and D Circuits A and C Circuits C and D All of the above circuits
2 marks
Page 25
QUESTION 7 A 100F smoothing capacitor is used to reduce the ripple voltage in a full-wave rectified power supply to an ohmic load. It was decided to operate a second identical load from the power supply as follows:
The ripple voltage with the second LOAD installed is likely to be about A. B. C. D. Half the original value. The same as the original value. Twice the original. No ripple voltage. 2 marks
QUESTION 8 The second LOAD was removed AND an additional two capacitors of the same value were added in parallel to the original:
Compared to the original peak-to-peak ripple voltage, it is now approximately A. B. C. D. A third of the original ripple. Two thirds of the original ripple. The same as the original ripple. Three times the original ripple.
2 marks
Page 26
The following information refers to Questions 9 and 10: The smoothed full-wave rectified voltage supplied to the input of a 6V IC voltage regulator (7806) is shown below in Figure 7. The voltage regulator has a 3.0V dropout zone requiring it to receive a minimum input of 9.0V. The smoothed voltage supply has a peak-to-peak variation of 2.0 volts and a peak of 12V. The LOAD has a resistance of 120 ohms.
Figure 7 QUESTION 9 Which of the following best represents the power dissipated across the 7806 voltage regulator? A. B. C. D. 0.25W 0.30W 0.50W 0.60W
2 marks
Page 27
QUESTION 10 The LOAD is changed for another resulting in the peak-to-peak ripple voltage increasing to 4.0V. The peak voltage remains at 12V.
Figure 8 Which of the graphs shown in Figure 8 best represents the output of the voltage regulator now? A. B. C. D. Graph 1 Graph 2 Graph 3 Graph 4
2 marks
Page 28
The following information applies to Questions 11 to 13: The circuit in Figure 9 uses a 6.0V zener diode to maintain a constant potential difference across a number of 300 ohm resistors. Switches 1 and 2 control current to the resistors. The zener has a power rating of 0.3W. Figure 9
QUESTION 11 When switch 1 is closed and switch 2 open, what current flows through the zener diode? A. B. C. D. 0.06A 0.04A 0.02A zero
2 marks QUESTION 12 Closing switch 2 so that both 300 resistors are connected causes current through the zener diode to: A. B. C. Increase Decrease Remain the same 2 marks
QUESTION 13 Select the best alternative from the options below. When switch 1 opens, A. B. C. D. The zener diode burns out. The current through the 50 ohm resistor reduces. The current through the 50 ohm resistor increases. The zener diode switches off.
Page 29
300
250
Stress (MPa)
Q
50 0 0 0.1 0.2 0.3 0.4
0.5
% Strain
QUESTION 1 Which of the four materials (A-D) has the greatest strength? A. B. C. D. M N P Q 2 marks
QUESTION 2 Which of the following properties (A-D) is true for material M? A. B. C. D. stiffest strongest largest strain energy toughest 2 marks
Page 30
QUESTION 3 Which of the following quantities (A-D) best represents the energy per unit volume to fracture for material N? A. B. C. D. 30 J/m3 300 J/m3 300 kJ/m3 30 MJ/m3
2 marks
QUESTION 4 Which of the four materials (A-D) is the most brittle? A. B. C. D. M N P Q 2 marks
QUESTION 5 Which of the four quantities (A-D) best estimates the value of Youngs Modulus for Material P? A. B. C. D. 500 Pa 500 kPa 500 MPa 50 GPa 2 marks
Page 31
Questions 6 to 9 refer to the following information: A balcony floor made of concrete is supported at the wall and by a support pillar 2 m from the wall. The balcony floor is 3 m wide as shown in Figure 2. Jeff is standing at the centre of the balcony floor. Jeff has a mass of 65 kg and the concrete floor has a mass of 200 kg.
a b
c d
Figure 2 QUESTION 6 Which one or more of the following positions indicated by the dots in Figure 2, (A-D) would be the best place to reinforce the balcony floor with steel mesh? A. B. C. D. a b c d 2 marks
Jeff now walks to the end of the balcony. The balcony is in static equilibrium. QUESTION 7 Which of the following types of forces (A-D) best describes the force at point d? A. B. C. D. shear compression tensile gravitational 2 marks
Page 32
QUESTION 8 Which of the following quantities (A-D) best estimates the force from the supporting pillar on the balcony floor? A. B. C. D. 248 N 265 N 2475 N 2650 N 2 marks
QUESTION 9 Which of the following quantities (A-D) best estimates the force acting on the balcony from the wall? A. B. C. D. 0N 175 N 1750 N 2650 N 2 marks
Questions 10 to 13 refer to the following information: A steel cable has a Youngs Modulus of 200 GPa. The cable has a cross-sectional area of 100 mm2 and is 50 m long. The cable is then stretched such that its length is now 50.05 m. QUESTION 10 Which of the following quantities (A-D) best estimates the % strain of the cable? A. B. C. D. 0.0001 0.001 0.099 0.1 2 marks
Page 33
The cable is now stretched further and experiences a stress of 500 MPa. QUESTION 11 Which of the following quantities (A-D) best estimates the net force on the cable? A. B. C. D. 50 N 50103 N 50106 N 50109 N 2 marks
QUESTION 12 Which of the following quantities (A-D) represents the new strain experienced by the steel cable? A. B. C. D. 0.0025 0.25 2.5 1105 2 marks
QUESTION 13 Which of the following statements (A-D) best describes why steel is used for cabling rather than aluminium which has a Youngs modulus of 70 GPa? A. B. C. D. Steel is not a composite material Steel is more elastic Steel is less brittle Steel is stiffer 2 marks
Page 34
THE SCHOOL FOR EXCELLENCE UNIT 3 PHYSICS 2009 COMPLIMENTARY WRITTEN EXAMINATION 1 SECTION A CORE STUDIES AREA OF STUDY 1 - MOTION IN ONE AND TWO DIMENSIONS
QUESTION 1 At terminal velocity the force of air resistance (up) is equal in magnitude to the weight force down. Therefore the force of air resistance is 2.25 N up (or 2.21 N up if using g= 9.8). [1 mark] for recognising |mg| = | Fair| [1 mark] for 2.25 N [1 mark] for direction = up QUESTION 2 p = Ft Fave =
p 13.5 = 54 N = t 0.25
[1 mark] for correct substitution into formula [1 mark] for 54 N [1 mark] for direction = up QUESTION 3 p = mv p = m(v-u) Take upward as positive: 13.5 = 0.225 (v -28)
13.5 = v + 28 0.225
60 = v + 28 v = 60 28 = 32 m/s upward [1 mark] for correct substitution into formula [1 mark] for 32 m/s [1 mark] for direction = upward
Page 1
QUESTION 4 C is the correct option. Speed does not take direction into account. The other 4 statements are essentially correct. QUESTION 5 Friction is providing the centripetal force.
Fc =
[1 mark] for correct substitution into formula [1 mark] for 750 N QUESTION 6 B is the correct option. The stone moves off tangential to its circular path. QUESTION 7 Andrew is correct (g = 2.45 N/kg). [1 mark] The gravitational field strength is inversely proportional to the square of the radial distance according to the equation:
g =
GM [1 mark] r2
When the radial distance is doubled, the gravitational field strength will be a quarter of its value at the surface of the Earth. QUESTION 8 The skaters initial vertical velocity is given by uy = 4.8sin28 = 2.25 m/s. [1 mark] Using this and the formula v = u + at gives: 0 = 2.25 10t t = 0.23 s [1 mark] for the time to reach the highest point. QUESTION 9 Total time of flight = 2 x 0.23 = 0.46 s Horizontal velocity = ux = vx =4.8cos28 = 4.238 m/s [1 mark] Therefore the attained range will be 0.46 x 4.238 = 1.95 m [1 mark] and given that the ramps are 2.0 m apart, he doesnt make it. [1 mark] QUESTION 10 Gravity acts down and air resistance acts to the left (opposing his motion) so the best answer is B. Air resistance is significant in comparison with the weight force. [1 mark]
Page 2
objects then the period will be greater for the lighter central mass (M). [1 mark] for explanation. QUESTION 13 According to: v =
GM R
v=
QUESTION 14 Using Pythagoras yields v = 4.24 m/s [1 mark] in the south-westerly [1 mark] direction. QUESTION 15 p = mv = 14 x 4.24 = 59.4 kgm/s [1 mark] south-west. [1 mark]
Page 3
I=
V 12 = = 0.24 A R 50
QUESTION 3 G1 has the greatest potential difference and current of all globes. As P=IV, G1 has the largest power and therefore the greatest brightness. QUESTION 4 Answer is C. An open switch at point Y will redirect all the current through G2 and increase the brightness. QUESTION 5 Answer is A. As all the current from the battery passes through point W, an ammeter at this point would measure the current from the battery. QUESTION 6 1000 QUESTION 7 1.8 1.9 V QUESTION 8 At 10mA, LED has a PD of 1.7 V, the thermistor has a PD of V = IR = 10 10 3 1000 = 10V Supply Voltage = 10+1.7 = 11.7V QUESTION 9 No as temp decreases, R increases and I decreases. Therefore LED turns off. QUESTION 10 Answer is B. QUESTION 11 Non-inverting as the gradient is positive.
Page 4
QUESTION 12 Gradient of graph: QUESTION 13 Axes labelled to 7V, clipping at 7V corresponding over the time intervals of 0.3-2.8 ms and 6.5-7 ms. Minimum at 1.3 V. Also show the output signal as non-inverted.
8
0 0 1 2 3 4 5 6 7
Time(ms)
QUESTION 14 20A
Page 5
Galileo postulated that all velocities are relative to the observer. QUESTION 3 Answer is C
Given that X sees flashes travelling toward him with speed of light, as simultaneous. Observer Y, moving relative to X, will be in a different position from X when flashes arrive, so for Y they will not arrive simultaneously. The one coming from the front of the train will arrive first. QUESTION 4 For X: Answer is B
100
100 = 87 m 1.15
Answer is A
QUESTION 5
According to X the scorch marks on the station will be equal to the length of the observed train which is 87m. According to Y these marks will be length contracted.
100
87 = 76m 1.15
Answer is D
QUESTION 6
t = to ;
QUESTION 7
The half-life as measured by the laboratory observer = 3.1 x 10-6 x 2.3 = 7.1 x 10-6s, Therefore distance travelled = speed x time = 0.9c x 7.1 x 10-6 = 1920m QUESTION 8 Answer is C
1 v2 1 c 2
1 1 0.97
= 4 .1
Page 6
QUESTION 10
Answer is B
Dependent on the relativistic mass and velocity of the object. QUESTION 11 Answer is A
No detectable velocity difference from light reflecting off each mirror QUESTION 12 Answer is A
Travel time to the star system in Earths reference frame = QUESTION 13 Answer is B
1 v2 1 c 2
= 3 .2
17.7
Page 7
From the graph the time constant is found to be about 10ms. Resistance = time constant / capacitance = 10 x 10-3 / 100 x 10-6 = 100 ohm QUESTION 3 Answer is B
When the diode is forward biased there will be a small constant forward potential across it. In the other half of the cycle when the diode is reverse biased, it will have the full supply potential (as though it was an open switch). QUESTION 5 Answer is C
To be deemed regulated it must provide constant output voltage over a range of load and supply voltages. In a voltage divider V OUT is dependent on the total resistance across it. QUESTION 6 Answer is G
Both C and D result in current passing the same direction through the load QUESTION 7 Answer is C
Adding a second LOAD doubles the current. Since V RIPPLE I LOAD , then ripple becomes double. QUESTION 8 Since V RIPPLE Answer is A
V 6 = = 0.05 A R 120 V + VMIN The average voltage supplied to the regulator is approximately 11V ( MAX 11V 2
The potential drop across the regulator is 11 6 = 5.0V PLOSS = V x I = 5.0 x 0.05 = 0.25W QUESTION 10 Answer is A
The trough of the ripple voltage crosses into the dropout zone of the voltage regulator resulting in a reduced output voltage from the IC regulator.
Page 8
QUESTION 11
I 50 =
V 3 = = 0.06 A R 50
V 6 = = 0.02 A R 300
The total current is unchanged at 0.06A, and with the switches closed each resistor draws 0.02A, resulting in only 0.02A flowing through the zener diode. QUESTION 13 Answer is A
With switch 1 open all current is directed through the zener diode.
PZENER = 6.0 0.06 = 0.36W which exceeds the diode power rating.
Page 9
Largest gradient = stiffest QUESTION 3 Area under graph: QUESTION 4 QUESTION 5 Gradient : Answer is C
QUESTION 6
Concrete is weaker under tension and needs to be reinforced at points b and c. QUESTION 7 QUESTION 8 Answer is B Answer is C
= 0
F = 0
FW + 2475 2000 650 = 0 FW = 175
QUESTION 10 Answer is D
% strain =
QUESTION 11
F = A = 500 10 6 100 10 6 = 50 10 3 N
Page 10
QUESTION 12
Answer is A
Page 11