Toshiba 27a44 Service Manual

FILE NO.
050-200411
SERVICE MANUAL
COLOR TELEVISION
27A44
DOCUMENT CREATED IN JAPAN, Mar., 2004
SERVICING NOTICES ON CHECKING

1. KEEP THE NOTICES
As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual.
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
2. AVOID AN ELECTRIC SHOCK

There is a high voltage part inside. Avoid an electric shock while the electric current is flowing.
3. USE THE DESIGNATED PARTS

The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used.
7. PERFORM A SAFETY CHECK AFTER SERVICING

Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE

In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is secured against implosion. However, when removing it or serving from backward, it is dangerous to give a shock. Take enough care to deal with it.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal Earphone jack
HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.) 1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER. 2. PART NO. and DESCRIPTION You can find it in your SERVICE MANUAL.
IMPORTANT
Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon.
A1-1
TABLE OF CONTENTS
SERVICING NOTICES ON CHECKING ..................................................................................... HOW TO ORDER PARTS .......................................................................................................... IMPORTANT ............................................................................................................................... TABLE OF CONTENTS .............................................................................................................. GENERAL SPECIFICATIONS .................................................................................................... DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ............................................................................................... 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................ SERVICE MODE LIST ................................................................................................................ CONFIRMATION OF HOURS USED ......................................................................................... WHEN REPLACING EEPROM (MEMORY) IC .......................................................................... ELECTRICAL ADJUSTMENTS .................................................................................................. BLOCK DIAGRAMS ................................................................................................................... PRINTED CIRCUIT BOARDS MAIN/CRT ................................................................................................................................ SCHEMATIC DIAGRAMS MICON ..................................................................................................................................... CHROMA ................................................................................................................................. DEFLECTION .......................................................................................................................... POWER ................................................................................................................................... SOUND .................................................................................................................................... TUNER/STEREO ..................................................................................................................... AV ............................................................................................................................................ CRT .......................................................................................................................................... COMB/FILTER ......................................................................................................................... WAVEFORMS ............................................................................................................................. MECHANICAL EXPLODED VIEWS ........................................................................................... MECHANICAL REPLACEMENT PARTS LIST ......................................................................... ELECTRICAL REPLACEMENT PARTS LIST ........................................................................... A1-1 A1-1 A1-1 A2-1 A3-1~A3-6 B1-1 B2-1, B2-2 C1-1 C1-1 C1-1 D-1~D-5 E-1, E-2 F-1~F-4 G-1, G-2 G-3, G-4 G-5, G-6 G-7, G-8 G-9, G-10 G-11, G-12 G-13, G-14 G-15, G-16 G-17, G-18 H-1, H-2 I-1, I-2 J1-1, J1-2 J2-1~J2-4
A2-1
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Deflection Magnetic Field Color System Speaker Position Size Impedance Sound Output NTSC3.58+4.43 /PAL60Hz G-2 Tuning System Broadcasting System Tuner and Receive CH System Destination Tuning System Input Impedance CH Coverage Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting G-3 Power Power Source Power Consumption Stand by (at AC) Per Year Protector Power Fuse Safety Circuit IC Protector(Micro Fuse) G-4 Regulation Safety Radiation X-Radiation G-5 G-6 Temperature Operating Humidity Operation Storage UL/CSA FCC/IC DHHS/HWC +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH AC DC at AC 125 W at AC 120 V 60 Hz 3 -Yes Yes No W at AC 120 V 60 Hz kWh/Year Yes Yes 120V AC 60Hz Picture(FP) Sound(FS) FP-FS US 1Tuner USA(W/ CATV) F-Synth VHF/UHF 75 ohm 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No MAX 10%(Typical) BV/BH 27 inch / 676mmV Normal 108 NTSC 2Speaker Front 2.0 x 3.5 Inch 8 ohm 2.5 + 2.5 W 2.0 + 2.0 W No System M degree +0.45G/0.18G
A3-1
G-7 On Screen Display Menu Menu Type Picture Contrast Brightness Color Tint Sharpness Audio Bass Treble Balance BBE On/Off Stable Sound On/Off Surround On/Off Set Up TV/CABLE(CATV) CH Program Add/Erase Option Language V-chip CH Label Favorite CH Lock On/Off Timer Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Game Timer Sleep Timer Sound Mute V-chip Rating 16: 9 G-8 G-9 OSD Language Clock and Timer On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode) more than -Sleep Timer Max Time Step Program(On Timer / Off Timer / Clock) English 120 Min 10 Yes No Min Sec Min Yes Yes Yes Yes Yes Yes Yes Yes Yes No French Spanish Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No
A3-2
G-10 Remote Control Unit Glow in Dark Remocon Format Custom Code Power Source Total Keys Keys Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down TV/Caption/Text CH1/CH2 TV/Video(TV/AV) CH RTN/CH ENT(Quick View) Sleep RE Call(Call) Reset Menu/Enter Mute Exit MTS(Audio Select) Fav.Up Fav.Down 16: 9 Multi Brand Keys CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) FF Rew Rec Play Stop TV VCR Cable DVD CODE Volume Up(DVD) Volume Down(DVD) DVD CLEAR TOP MENU DVD MENU DISPLAY Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Voltage(D.C) UM size x pcs RC-GW Yes Toshiba TV:40-BF h 3V UM-4 x 2 pcs 49 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Keys
A3-3
G-11 Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type BBE Auto Search CH Allocation SAP Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect CH Lock Video Lock Game Timer (Max Time:120 Min) Energy Star Favorite CH Surround 16:9 Mode 2 Tuner P-in-P Yes Yes No No Yes Yes Yes Yes Yes Yes No Yes 3 Lines Yes No Yes No No No Yes No Yes Yes Yes USA,Toshiba Type No No No Yes No No Yes Yes No
A3-4
G-12 Accessories Owner's Manual Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) ESP Card PTB Sheet 300 ohm to 75 ohm Antenna Adapter Yes No[From '04 MAR O/R] No No Yes UM4 size x 2 No No No No No No No No No No No No No No No Language W/ Warranty English /French Yes Yes No
A3-5
G-13 Interface Switch Front Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down Rear AC/DC TV/CATV Selector Degauss Main Power SW Indicator Power Stand-by On Timer Terminals Front Video Input Audio Input Other Terminal Rear Video Input(Rear1) Video Input(Rear2) Audio Input(Rear1) Audio Input(Rear2) Video Output Audio Output S- Input Euro Scart Color Stream Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet G-14 G-15 G-16 Set Size Weight Carton Master Carton Content Material Dimensions Gift Box Material Dimensions Design Description of Origin Drop Test Height (cm) Container Stuffing G-17 Cabinet Material Cabinet PCB G-18 Environment Pb Free Cd Free Cabinet Front Cabinet Rear Non-Halogen Demand Eyelet Demand Lead-free Solder Yes No No W x D x H(mm) W x D x H(mm) -Yes Double/Brown 850 Yes Natural Dropping At 1 Corner / 2 Edges / 4 Surfaces 60 (ORION SPEC:31) 168 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No x 575 x 665 As per Buyer's Description of Origin ----x -Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) 37.0kg 41.0Kg F Type No 740 x 491.5 x 571.5 ( 81.6 lbs) ( 90.4 lbs) No Sets /-x -No RCA x 3 No No No RCA RCA RCA x 2 RCA x 2 RCA RCA x 2 Yes No RCA RCA x 2 No Yes(RED) No No Yes Yes Yes Yes No No No No Yes No No No
A3-6
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)
Fig. 1-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Screwdriver
CRT Support Alligator Clip Fig. 1-4
GND on the CRT
Fig. 1-1 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.
2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Rubber Cap
CRT CRT Support Fig. 1-2
Support Fig. 1-5
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts. B1-1
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
Masking Tape (Cotton Tape)
IC
Tweezers
Fig. 2-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) NOTE Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely. 4. Peel off the Masking Tape.
Fig. 2-3
5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Blower type IC desoldering machine
Braided Shield Wire
Soldering Iron
IC
Fig. 2-2
IC pattern
Fig. 2-4
B2-1
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Soldering Iron. (Refer to Fig. 2-8.)
Thin-tip Soldering Iron
IC
Soldering Iron
Fig. 2-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, always be sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.)
Solder
Soldering Iron
IC
Supply soldering from upper position to lower position
Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Braided Shield Wire
Fig. 2-7 B2-2
SERVICE MODE LIST

This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key VOL. (-) MIN Remocon Key 0 Releasing of V-CHIP PASSWORD. Initialization of the factory. NOTE: Do not use this for the normal servicing. If you set a factory initialization, the memories are reset such as the channel setting, and the POWER ON total hours. POWER ON total hours is displayed on the screen. Refer to the "CONFIRMATION OF HOURS USED". VOL. (-) MIN 6 Can be checked of the INITIAL DATA of MEMORY IC. Refer to the "WHEN REPLACING EEPROM (MEMORY) IC". VOL. (-) MIN VOL. (-) MIN 8 9 Writing of EEPROM initial data. NOTE: Do not use this for the normal servicing. Display of the Adjustment MENU on the screen. Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment). Operations
VOL. (-) MIN
CONFIRMATION OF HOURS USED

POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0". ADDRESS DATA 1. Set the VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. Initial setting content of MEMORY IC. INIT 00 90 3. After the confirmation of using hours, turn off the power. POWER ON total hours. CRT ON 0010
= (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
FIG. 1
WHEN REPLACING EEPROM (MEMORY) IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: No need setting for after INI 1F due to the adjustment value. INI 00 10 +0 90 50 +1 E8 00 +2 02 00 +3 65 00 +4 5E 00 +5 B3 00 +6 24 00 +7 37 99 +8 39 3F +9 AC 0F +A AA 0D +B 04 E6 +C 40 A8 +D 40 21 +E 40 42 +F 7F 00
Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. ADDRESS and DATA should appear as FIG 1. 3. ADDRESS is now selected and should "blink". Using the VOL. UP/DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using VOL. UP/DOWN button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 9. Turn POWER on. 10. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 1 second. 11. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC. C-1
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION Use an isolation transformer when performing any service on this chassis. Before removing the anode cap, discharge electricity because it contains high voltage. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. When you exchange IC and Transistor for a heat sink, apply the silicon grease on the contact section of the heat sink. Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.) Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter 3. Multi-sound Generator 4. Pattern Generator On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 1 second to appear the adjustment mode on the screen as shown in Fig. 1-1. TV
2. BASIC ADJUSTMENTS
2-1: CONSTANT VOLTAGE 1. Place the set with Aging Test for more than 5 minutes. 2. Using the remote control, set the brightness and contrast to normal position. 3. Set condition is AV MODE without signal. 4. Connect the digital voltmeter to the TP003. 5. Adjust the VR502 until the digital voltmeter is 123 0.5V. 2-2: CUT OFF 1. Place the set with Aging Test for more than 15 minutes. 2. Set condition is AV MODE without signal. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select "CUT OFF". 5. Adjust the Screen Volume until a dim raster is obtained. 2-3: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 10 minutes. 2. Receive the gray scale pattern from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (12) on the remote control to select R CUT OFF. 5. Press the CH. UP/DOWN button on the remote control to select the R CUT OFF, G CUT OFF, B CUT OFF, B. DRIVE or R. DRIVE. 6. Adjust the VOL. UP/DOWN button on the remote control to whiten the R CUT OFF, G CUT OFF, B CUT OFF, B. DRIVE, and R. DRIVE at each step tone sections equally. 7. Perform the above adjustments 5 and 6 until the white color is looked like a white. 2-4: FOCUS
00 OSD
35 Fig. 1-1
3. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 4. Press the MENU button on the remote control to end the adjustments.
NO. 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 FUNCTION OSD H CUT OFF H. VCO H. PHASE AFC GAIN V. SHIFT H. SIZE V. SIZE V. LINEARITY VS CORRECTION DRIVE R DRIVE B R CUT OFF G CUT OFF B CUT OFF BRIGHT MAX BRIGHT CENT BRIGHT MIN CONTRAST MAX NO. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 88 FUNCTION CONTRAST CENT CONTRAST MIN COLOR MAX COLOR CENTER COLOR MIN TINT SHARPNESS Cb DELAY FINE Cr DELAY FINE Cb PEDESTAL ADJ Cr PEDESTAL ADJ E/W PARABOLA E/W CORNER E/W TRAPEZIUM LEVEL SEPARATION1 SEPARATION2 READ DATA
1. Receive the monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 2-5: HORIZONTAL PHASE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select H. PHAS. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum.
Fig. 1-2 D-1
2-6: HORIZONTAL SIZE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (06) on the remote control to select H. SIZE. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes 11%. 2-7: VERTICAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Adjust the VR401 until the horizontal line becomes fit to the notch of the shadow mask. 2-8: VERTICAL SIZE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select V. SIZE. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes 9 2%. 2-9: VERTICAL LINEARITY NOTE: Adjust after performing adjustments in section 2-8. After the adjustment of Vertical Linearity, reconfirm the Vertical Position and Vertical Size adjustments. 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (08) on the remote control to select V. LIN. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum. 2-10: TRAPEZIUM 1. Receive the crosshatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (32) on the remote control to select TRAPEZIUM. 4. Press the VOL. UP/DOWN button on the remote control until the both vertical lines of the screen become parallel. A 2-14: BRIGHT CENT 1. Receive the monoscope pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI CENT". 4. Press the VOL. UP/DOWN button on the remote control until the white 0% is starting to be visible 5. Receive the monoscope pattern. (Audio Video Input) 6. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~4. 7. Press the TV/VIDEO button on the remote control to set to the CS mode. 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI CENT". 9. Press the VOL. UP/DOWN button on the remote control to set the same step numbers as the AV mode. 2-13: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-1) 2-11: PARABOLA 1. Receive the crosshatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (30) on the remote control to select PARABOLA. 4. Press the VOL. UP/DOWN button on the remote control until the right and left vertical lines are straight. 2-12: LEVEL 1. Receive the VHF HIGH (70dB). 2. Connect the AC voltmeter to pin 6 of CP101. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (33) on the remote control to select "LEVEL". 4. Press the VOL. UP/DOWN button on the remote control until the AC voltmeter is 75 2mV.
TV
00 OSD
35 B
Fig. 2-1
D-2
2-15: TINT/COLOR CENT 1. Receive the color bar pattern. 2. Connect the oscilloscope to TP024. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (24) on the remote control to select "TINT". 4. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes as straight line (Refer to Fig. 2-2) 5. Connect the oscilloscope to TP022. 6. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "COL.CENT". 7. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 120 10% of the white level. (Refer to Fig. 2-3) 8. Receive the color bar pattern. (Audio Video Input) 9. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~7. 10.Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 2~7. 2-17: SEPARATION 1, 2 Please do the method (1) or method (2) adjustment. Method (1) 1. Set the multi-sound signal generator for each different L-ch and R-ch frequency (Ex. L-ch=2KHz, R-ch=400Hz) and receive the RF. 2. Connect the oscilloscope to the Audio Out Jack. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (34) on the remote control to select SEP 1. 4. Press the VOL. UP/DOWN button on the remote control to adjust it until the audio output wave becomes a fine sine wave. 5. Press the CH UP button once the set to "SEP 2" mode. Then perform the above adjustment 4. Method (2) 1. Set the multi-sound signal generator L-ch=1KHz, R-ch =Non input and receive the RF. 2. Connect the oscilloscope to the Audio Out Jack (R-ch). 3. Press the AUDIO SELECT button on the remote control to set to the stereo mode. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (34) on the remote control to select SEP 1. 5. Press the VOL. UP/DOWN button on the remote control to adjust it until the R-ch output becomes minimum. 6. Set the multi-sound signal generator L-ch=Non input, R-ch=1KHz and receive the RF. 7. Connect the oscilloscope to the Audio Out Jack (L-ch). 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (35) on the remote control to select SEP 2. 9. Press the VOL. UP/DOWN button on the remote control to adjust it until the L-ch output becomes minimum. 2-18: Confirmation of Fixed Value (Step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. NO. 02 04 05 09 15 17 19 20 21 23 25 26 27 28 29 31 FUNCTION H.VCO AFC GAIN V.SHIFT VS.CORRECTION BRI.MAX BRI.MIN CONT.CENT CONT.MIN COL.MAX COL.MIN SHARPNESS CB DL CR DL CB PED CR PED CORNER RF 03 04 02 38 140 45 64 20 90 00 40 00 00 08 08 35 AV 03 04 02 38 140 45 64 20 90 00 40 00 00 08 08 35 CS 03 04 02 38 140 45 64 20 90 00 40 00 00 08 08 35
"A" Fig. 2-2
white 100%
red 120% Fig. 2-3
2-16: CONTRAST MAX MANUAL 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select CONT. MAX. 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes 110. 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 5. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 1~3. D-3
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue color. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB
R G B UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT Fig. 3-2-a
R G B
WEDGE
WEDGE
WEDGE WEDGE POSITION Fig. 3-2-b
PURITY MAGNETS 6 POLE MAGNETS 4 POLE MAGNETS Fig. 3-1
D-4
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CRT PCB
CP806 TP024 TP022 J801 R805 R803
CP803
CP802B
CP801B
CD801 CRT CD802
CP801A CP101 TU001
FB401 CP401 VR401 TP003 W003
VR502
AC IN CRT
CP501 CP1001 J707
CD501 CP802A CP502 L503 CRT J705 J706
SPEAKER
MAIN PCB
D-5
BLOCK DIAGRAM
TU001 17 11 10 13 12
MICON IC101 OEC7090A
SPEAKER SP1001
30 SCL1 31 SDA1
5 AFT S_IN 11
VIDEO 3
S INPUT
YUV IN
12
CHROMA IC IC601 M61283FP R70T
SOUND AMP IC IC1001 AN17808B

46
CVBS1
53
CVBS4
27 26
SCL
40 44 48
V IN U IN Y IN
2 18 19 14 2
SOUND DECORDER IC IC902 AN5829S 22 21
FSC OUT
63 V OUT FBP IN
H OUT ACL
SDA
L R R
G OUT
R OUT
B OUT
3 23
AUDIO 3 AUDIO 1/2

18 SDA 17 SCL 16 19
17
16
15
14
55
24 L
11
COMB FILTER IC IC1501 LA76605M-TLM

16 18
TONE CONTROL IC IC302 AN5891SA-E1V
30
S INPUT
A/V OUT
HV S FBT FB401 10 7 1 9 6 3 +180V +25V Q502 SWITCHING 10 T501
5 3
6 11 10 F
8 CRT V801 7
SOUND+B +B
15
IC504 LTV-817M-VB
FEED BACK 1 V.OUTPUT IC IC401 LA78041 5 DY
H. OUT Q402 Q405
E-1
E-2
D404 TP003 W002 R500 TP004 D501 R542 D502 C513_1 C503 D504 C502 CP502 CP507 F501 CP501 FH501
_1 C5 08
R438 R443 C415 W001 D503 R502 RY501 C506_1 R520 L501 CP508 TH501_1 FH502 R544 Q514 HS501 R501 C507 D507 R432 W003 R430
Q502
C535
C512 W801 B501 C505_1 SW105 W004 R539 R540 R541_1 D523
FB401_2
W005
D524 R545 R543_1
T501
D516
D509 W802 R508 R807 R803 R805 D506 Q802 Q806 D525 OS101
IC504
R547 D508 D812 R510 CP801B CD801B Q804 D810 D801 W013 C108 R120 D109 R802
C524
W007 W009
09
W010 VR502 Q507 R506 Q801 D802 W817 CD802B W825 CP802B C801 Q803 CP806_1 R102 D514 D811 W016 Q805 W011 D520 R806
D4
W006
_1 12 C4
D407
R554 R553 D408_1 W012 B504 W863 D512 Q504 C520 C521 D511 D517 C802
01 _1
C426
D528
C509
D803
C421_1
D405
B403
R824
J8
Q505
CD801A
CP801A
Q405
PRINTED CIRCUIT BOARDS MAIN/CRT (INSERTED PARTS)
C527 C501 C504 W042 W043 C523 W806 W056
R505
C425
C517
C413_1
Q503
R434
R536 C539 R512 R503 Q508
D510
R524
CP401
C409 D410 W033 C110 C139 W035 W032 W037 W038 W040 Q509 R426 W039 D406
SOLDER SIDE
W055
R515
C427
L402 R527 W021 R535 R428 W019 R537 C403 W008 W023 C550
W827
W052 W054 C122
D403 IC401
W823 W020 B405
R459_2
R433 D414 T401 C442 C417 R414 C402 R406 W029 R437 R002 Q402 W027 W024 W044 W041 W030 D417 R410_1 D402 R455_1 R418 W836 C408 D419 W048 W185 W046 W045 R436 W071 TP006 Q408 W084 W026 W025 W022 D415 D416 C401 C407 C406 R413 R001 R429 C422_1
D113 W053 X101_1 R146
C430 R421 VR401_1 R441 D608 W018 Q410 R427 W017 R422
R132 R124
C113
W861
CP101
HS401
R118 W097 W103 W091 W805 W107 W108 W094 W106 R130 R140 R139 W128 R119
W065 TP005
W123 W120
W081
R419 R457 R517_1
R456 W844
Q409
W121
J708
W078
W086
W085
C728 D513
W080
C645
W114 W099 W111 W113 W098 W083
D104
W811
W093
D105 W116 W104 W109 W101 W102
D701
J704
W057
C711 C707 C621 W075 W186 W074 W077 W076 W070 W073 W072 W090 W183 W068 W067 W079 W187 W089
R710
W064 D703 W058 D702 W061
W125
C638 C627 C618
W829
W060
W088
W069
W087
W082 C642 C646 C611
W100 D607
D705
J703
W063 R701 C710 W059 W062 R702 C705 W130 C708 C622
W095 W184 Q607 C605 R616 Q606 C609_1 D601 D602 Q602 W115 C629 W110 W139 Q604 Q601 D603 C615 C608 C603 R603 Q611 C606 W170 W169 CP802A CD802A R626 W167 D606 D605 R902 R901
C901
C910 C905 C903 C902 W176 W092 W174 R904 R905 W180 W117 W175 R302 L301 J705 C904
J701
C1004 D704 C1007 W131 W132 C733 W134 C1003 W803 W135 R1009
W157
C306 R623 W155 D604 W150 W151 C1008 C610 R648 W140 W144 W173 C602 W172 W815 W142 C304 C317
C302 C333 R301 W141 R601 C305 C308 J706
J702
C701 C702 W819 W820 D709 C001_1 W812 D001
C1009 HS1001 IC1001
L1512 W154 W143 C1002 C1005 C1011_1 W858 L1501 W136 W148 W149 W147
W165 C321 C318
R6
R649
02
C1502 C1518 C1520 C1001 W137 W145 W835 C1532 W146 L1508 W848 C1501
W168
W164 W181 W163 W166 L1503 L1502 C316 C319 R304 CP1001 R303 J707
C314
TU001
C1535 W162 C1510 W133 W138 W156 L1511 L1505 L1510 C1528 C1530_1 C1525
W834 W831 W160 W161 W832 W177 W178 W179 W833
D706
C916
W096
W830
C919
C914
W119
C630
X602
L901
C907
W118
W112
W129 W126
SW103
SW104
F-1
R4
52
W828
W028 C109
W822 D106
C114
W049
Q512
R133
L40
SW101
HS402
SW102
R546
C418
D505
C420_1
CP803
D411
R507
R804
W015
F-2
- REPLACE AS MARKED. RISK OF FIRE
C519 _1
R4 39
R612
R907
C737 R734
Q902
R906
R724
C628 R635 R641
R709 IC702 R705 Q709 R1013
C640 R1523 R610
C706 C724 C727 R726 C722 C736
C303
C719
R706 IC701 R729 R733 C725 C738 R739
C301
Q605 Q614
Q1001
R605 C607
C734 R735
C1507
R1004 C005
Q1504
R1003
C1523
C1515 R1509
C1512 C1514 R1512 C1516
R1503
R1506 R1530 C1531 C1517 R1505 Q1503 C002 R006 C1519
Q1508
C1521
1 60 IC
F-3
R404 R810 C541 R532 R533 R801 C554 C511 R811 R815 C809 R819 R813
B_SHORT
R808
Q101
B_SHORT
R821 R809 R812 R817 C811 R820 R814 R818 C810 R816 C805_1
R513 R516 R103 R106 R525 R511 C510 R112 R113 R114 R519 C416 C405 R407 R453 R403 R417 R415 Q411 R448 R461 R462 R409_1 C131 C146 C120 R126 R150
SOLDER SIDE
C119 C111
C106 R137 R131
C121 C117 R125 R109 C115 R138 IC101 R110 C104 C102 R101
R128
C411 R449 R458 C439
PRINTED CIRCUIT BOARDS MAIN/CRT (CHIP MOUNTED PARTS)
Q103
R401
R135 C141 R136 C643 C644 C637 IC199_1
C136 C137
Q711 R721
R711 R627 R704 Q712
R127 R142 R141 R628 R632 R143 C138 R129 C135
R134 C128 C140 C142
R730
R618 C632 R703 R736 R617 C624 R728 R727 C735 C631 33
R145 R625 R708 R725 C619_1 R622 C913 C917 R634 R629 R912 C614 C641 R903 49 R609 R607 R1529 R1508 Q901 17 C647 C143 C911 C918 C915 IC902 C912 C908
R1010 R1011 C1010 C1012
R1528 R1504
1 C616 R654 C612 R636 R611 R620 Q603 R608 R606 R604 C635 R613 R1522 R1510 C1506 IC1501 C1503 C1513 Q1507 C1509 R1507 C1508 C1504 C1505 R1502 R1516 R1518 IC1502 IC1503
C639 R1520 C1533 R1519 C1526
R314 C307 C309 C310 C313 C741
IC302
C315 C322
C334 C311 C312 C720
R745
C742
R746 C320
F-4
A
ACCESSORY
MICON SCHEMATIC DIAGRAM

(MAIN PCB)
8
OS101 RPM7138-WH5 B+ 3 GND 2 D109 SLR-342VCT32 POWER ON LED SW Q101 KTC3875S_Y_RTK 2.7 0 0 R109 1K Vout 1 5.0 0 4.9 16V 10 KA C108 CP101 173979-7 GND I2C_SCL I2C_SDA I2C_OFF GND R103 2.7K SW101 EVQ21505R SW103 EVQ21505R SW102 EVQ21505R VOL DOWN CH DOWN VOL UP CH UP 1 2 3 4 5 6 7 47 1/4W
BT001 R03(AB)E_2P_G
7
R101
560
R102
BT002 R03(AB)E_2P_G
TM101 R25-1939
270 1/4W
R120
R106
560 SW104 EVQ21505R SW105 EVQ21505R 1K 1/4W POWER R124
AUDIO L AUDIO R
R130 47K 1/4W
R150 1K
1.8 0 0 CLAMP SW Q103 KTC3875S_Y_RTK
FROM/TO CHROMA
100 1/4W
C142
R146
MICON IC IC101 1 5.0 4.0 0 NC AUDIO MUTE EXT MUTE VOLUME BBE SW AFT KEY 1 KEY 2 X RAY REMOCON ON_TIMER S_IN Y/C_SW AUDIO_SW OEC7090A 42 H_CTL PROTECT 12C_OFF SYNC H SYNC V SYNC BLUE B GREEN G RED R BLANK CLOCK_CNT SDA1 SCL1 0 R126 0 5.0 2.1 4.0 4.8 0 C131 0 0 0 R141 R142 R143 820 820 5.0 NC 5.0 R135 5.0 R136 5.0 5.0 5.0 2.4 2.0 2.0 1.0 5.0 R125 10 VCC C109 0.1 B C128 0.1 50V 0.47 KA YK C114 F 5.0 5.0 0 5.0 MEMORY IC IC199_1 S-24C16AFJA-TB-01 22 C117 47P CH R133 C111 0.001 B 2 4.7K 4.7K 820 150P CH R127 3.9K R128 3.9K R129 3.9K 10 33 0 W811 D105 100 C120 0.001 B C146 33P CH
AT+5V PROTECT CLAMP_OFF SYNC_OUT HD VD OSD_B C136 C137 B OSD_G OSD_R D104 OSD_BLK C138 1SS133 SW_Y_OUT RESET POWER SDA SCL B 0.1 0.1 B
6
TO SOUND
220P
CH R118 2.2K 1/4W
C143 220P TV_MUTE CH
R110 10K
FROM TUNER/STEREO
R112 2.2K R113 2.2K
AFT
37
5.0 5.0 2.2
38
0.1
3.2
39
40
41
16V 10 KA
R114 47K R119 22K 1/4W C140 220P CH C141
FROM/TO AV EXT_MUTE S_IN AUDIO_SW
C139
34
5.0
35
36
FROM/TO TUNER/STEREO 10P CH R145 2.2K C135 1SS133
11
32
0 0 5.0 0 NC 3.5
R139 100 1/4W R140 100 1/4W 4 3
J_AUDIO_OUT_R J_AUDIO_OUT_L SDA SCL FROM/TO SOUND
12
13
14
FROM/TO DEFLECTION
NC P FAIL DEGAUSS H X-RAY TEST CNVSS X.IN
POWER MCU_CLOCK RESET CVIN VHOLD HLF FILT
29
30
31
220P CH
15
H_CTL 16 27 X-RAY MTZJ5.1B 5.0 3.2 NC 0 C102 C104 27P CH 27P CH X101_1 100CT8R005 8MHz 1 2.3 1.7 0 21 VSS C115 820P CH C113 0.1 B R131 1K C119 220P CH C121 0.01 B 20 X.OUT 23 100 R138 R132 1/4W C122 50V 1 KA 1M
28
R134
10K
SDA SCL
0.1 B
17
FROM/TO POWER X-RAY P.FAIL
C106
D106
18
19
DEGAUSS_H GND POWER
24
25
26
TO COMB FILTER
1K
1/4W
Y/C_SW
6.3V 2200
MTZJ5.6B
C110
R137
D113
10K
MODE
SDA
6 SCL
8 VCC
VSS
E2
W822
E1 0 2 0
E0 1 0
PCB010 TMC559
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
G-1
G-2
CHROMA SCHEMATIC DIAGRAM

(MAIN PCB)
8 8
FROM/TO AV
VIDEO_IN2 V_IN[YUV] VIDEO_IN1 U_IN[YUV] Y_IN[YUV] VIDEO_IN3 R618 100 8.2K VIDEO_OUT R616 120 1/2W R617 5.5 8.8 4.9 AT+5V REG Q607 KTC3203_Y
0.015 B
C631
C632
R603 1SS133 MTZJ8.2B 330 1/2W MTZJ15B D602 D603
18P CH
7
R634 R622 5.6K 16V 47 YK 1K
16V 47 YK
50V 1 KA
50V 1 KA
50V 0.47 KA
C605
C619_1
16V 47 YK
50V 1 KA
50V 1 KA
3.579545MHz
X602 100CT3R505
0.1 B
C614
C607
C610
C611
C624
C618
C621
D601
C627
C630
0.1
0.01
FROM/TO COMB FILTER C_V_OUT_SW P.CON+5V Y_V_OUT_SW VIDEO_OUT 7 R602 12 3W
0.1
12
C622
FROM/TO MICON 2.7 P.CON+5V REG Q606 KTC3209_Y 5.0 7.2 3W 5.0 P.CON 5V REG Q602 KTC3209_Y 5.0 7.2 5.5 7.2 5.5 P.CON 5V REG Q604 KTC3209_Y 5.5 50V 1 KA 48 C641 0.1 B 2.2 49 C IN(Y/C) NC(GND) Y IN(Y/C) VREG VCC CVBS4 5.7V VREG OUT fsc OUT NC FAST YUV DELAYDE Y OUT 1 HVCO F/B 59 EW OUT VIDEO LINE OUT 8.7 VREG OUT HVCO F/BDEF GND1 VRAMP AGC CAP LOGIC GND V OUT VRAMP CAP 1 W815 3.2 MMTS 4.0 2 0 2 AFC FILTER 15 G OUT 22 16 B OUT G IN B IN V PULSE OUT INV.FBP OUT DEF GND2 DEF VCC MONITOR OUT HI VCC R OUT ACL 15 4.0 4.0 14 R641 10K 9 R635 CH CH C647 C646 120K R636 10 0.012 16V 1000 YK 100P CH D605 1SS133 1.5K 0.1 B R612 C629 C628 C639 B 13 R625 KANP R632 6.8K 33K 16 15 CHROMA IC IC601 M61283FP R70T 47 NC(GND) 48 Y IN(YUV) 54 33 V/C GND 34 XTAL 3.58 27 SCL SDA CLK CONT FAST BLK R IN 0 3.0 8.7 1.9 R610 100 16V 47 YK C640 0.01 F 5.7 3.2 0 NC 0 2.8 NC 3.0 3.0 8.7 4.0 3.9K R606 330 R608 4.0 8 4.0 0 3.0 47 46 CVBS1 0 1.2 45 44 NC(GND) U IN(YUV) 0 1.9 5.0 1.2 43 42 41 40 NC(GND) CVBS2 V/C VCC V IN(YUV) 0 1.9 5.6 2.8 39 38 37 36 NC(GND) CVBS3 MCU 5.7 VREG OUT C_APC 0 3.2 35 34 NC(GND) 0 33 32 3.6 SW_Y_OUT 0 NC 5.0 3.5 NC 5.0 3.5 3.5 4.9 NC 4.2 2.9 C637 2.9 C643 2.9 C644 4.6 4.9 4.9 2.1 11 SYNC_OUT R629 6.8K D608 11E1-EIC CLAMP_OFF W805 33P CH 33P CH 33P CH R627 SCL 100 R628 SDA 100 POWER AT+5V RESET PROTECT
Y SW OUT NC MCU RESET
P.CON+8V[A] FSC_OUT
R649 12
50
C642
51
52
MCU CLOCK OUT P_CON CONT
53
FROM/TO TUNER/STEREO
55
C603
TUNER_VIDEO TUNER+5V
56
57
24
25
26
28
29
30
31
P.CON+8V[B] P.CON+5V
OSD_BLK OSD_R OSD_G OSD_B VD HD
10 1/2W
58
TO SOUND
61
P.CON+8V[B]
2.2
R613 390 22P CH R604 C635 1K
62
63
NC(Vcc)
NC(Vcc)
FBP IN
H OUT
64
NC
NC
FROM POWER R601 UNREG+12V GND 15 1/2W 11.3 7.9 P.CON 8V REG Q611 KTC3209_Y TF C606
17
18
19
20
6dB AMP Q603 KTC3875S_Y_RTK
6dBAMP Q614 7.9 KTA1504S_Y_RTK 7.8 7.3 3.8 3.8
7.3
6dB AMP Q605 KTC3875S_Y_RTK C608 16V 47 YK
R605
R648
330 R607
10K
60
1.7
2.3
21
23
3 0
4 0
5 5.5
6 0
7 NC 3.8
8 8.0
9 8.0
10 0
11 8.0 NC
12 8.0
13 4.0
14
R654 C609_1 56K 50V 1 KA C615
0.33
C638
7.9 8.5 16V 100 YK FROM/TO DEFLECTION C645
11.3
8.5
0.1
MTZJ12B
1SS133
R609 16V 47 YK D604 100
0.01
C616
P.CON 8V REG Q601 KTC3209_Y C602
C612
16V 10
100P
100P
1SS133
R611
D606
D607
6.8K
TO CRT/SVM CP802A B2013H02-7P P.CON+8V R620 100 R623 100 1/4W R626 100 1/4W NC GND R.OUT G.OUT B.OUT CLAMP_OFF 1 2 3 4 5 6 7
10K
P.CON+5V P.CON+8V[A] GND V_OUT EW_OUT H.OUT H_SYNC ABCL
PCB010 TMC559
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-3
G-4
DEFLECTION SCHEMATIC DIAGRAM

(MAIN PCB)
8
FROM/TO DY V.OUTPUT IC IC401 LA78041 + R401 PUMP UP VCC GND 1 2 3 4 4.0 25.0 2.0 0 560 1/2W 560 1/2W R429 560 1/2W 4.7K CH R421 R433 C422_1 C416 THERMAL PROTECTION 100V 0.1 MMTS AMP 18 CP401 B06B-DVS 6 5 L402 ELH5L4132N NC NC 4 3 2 1 R439 35V 100 YK 1/2W 1K 1W C425 2KV 0.001 R 6 5 4 3 2 1 V801 M68LWF088X
R407 1.2K 10K 1SS133 1SS133 1SS133 220 1/4W +-1%
16
5 12.0
6 25.0 17
7 4.0
9 10 8 6 11
R G B 5 7 1
7
D419 R455_1
100P
7
1 2
TO CRT/SVM (CP805)
W836
11E1-EIC C407
D402
R427
D416
CD803_1 CU823001
R462
R418
8.2K +-1% C406 R415 50V 1 YK 820 12K +-1% 560P CH R413
25V 1000 MHE
820 1/2W
2.9 2.3 0.7 0
100V 0.22 MMTS
BUFFER Q409 KTA1266 2.3 R456 5.6K 1/2W
4.7K 1/4W
D417
R457
R414
R417 FB401_2 FJN27A003_M 115 1 V.POSI ADJ VR401_1 2.2K METAL 180 COL HV 39K C408
1.0 0.4
C409
R448
2.5
2.9
50V 6.8 UHT
R422
0.7 R461 R449 27K 1K HS401 763WAA0191
R419
FROM/TO CHROMA V_OUT EW_OUT GND P.CON+8V[A] P.CON+5V H.OUT H_SYNC ABCL
C442
6.5 DRIVE Q410 0 2SC4159
1W
68K
1/2W
1 1/2W
680 1/2W
R437
MTZJ30B
BUFFER Q408 KTA1266
R459_2
50V 10 YK D410 D403
BUFFER Q411 KTC3875S_Y_RTK
MTZJ30B
C417
820
E180 6 108.0 B+ 2 105.0 AFC 9 HEA 0 TER 10 0 0.2 2.0 8 4 3 8 0.1 5 GND E12 E27 GND E8
R458
1K
C405
6
F S GND 0 11 ABL 8.1
1.2
W827
W828
W823
C411 0.001 CH C401 MMTS 19 17.3 0 26.3 T401 ETH19Y203AY 0 5 1 4 0.1 3 2 0.0027 CMPP H.OUT Q405 2SD2499(LBOEC1) 115 20 B405 W4BRH3.5X6X1.0 50V 22 YK R428 0.1 100 1/4W B403 0 21 0.015 250V 0.43 PMS 02DK000058
ERD07-15L50
C412_1
630V 0.022 CPP 1.25KV
500V 27P SL C402 R409_1 1K R453 10K FROM/TO POWER R403 H.DRIVE Q402 KTC3227_Y 0.4 1K
D408_1
C418
C420_1
CMPP L403
5
TP004 PROTECTOR TEST TP003 ANORD
100V 0.01
17.3 R406 0
W4BRH3.5X6X1.0
1.25KV
FE201-6L49
C421_1
470 1/2W
C403
HS402 763WAA0231
D409
B_SHORT
GND R434 +B 1.8 10W W863 R452 390 2W D414 11E1-EIC D415 11E1-EIC R410_1 47 2W
FORCUS FROM/TO CRT SCREEN
FBT+B
D405 AU02A-EIC
H+B
R443 150K 1/2W C427 100V 0.1
W861
R404 MTZJ5.1B 100 D404
R432 8.2K 1/2W C415 500V 150P B 68K 1/2W R430
MMTS
3
AU02A-EIC D407
FROM/TO MICON 1.2 2W R438 R436 18K 1/4W +-1% TP005 TP006 R441 15K +-1% 100V 22 YK C430
H_CTL W844 MTZJ5.6B 1/4W +-1% 0.01 B D411 AU02A-EIC
35V 1000 YK
X-RAY D406 R426
C413_1
TO CRT/SVM MHE CP801A B2013H02-5P 180V NC NC NC NC GND HEATER 1 2 3 4 5
C439
C426
250V 22
4.7K
X-RAY TEST
PCB010 TMC559
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
ARE
G-5
G-6
POWER SCHEMATIC DIAGRAM

8
(MAIN PCB)
D516 1SS133 10.9
RELAY DRIVE Q504 KTC3198 0
R515 10K 1/4W
C513_1
C519_1
KX
RY501 ALKS321 2 3 DEGAUSS COIL L503 8R270010 1 2 TH501_1 CP507 003P-2100 1 1.5M 1/2W R520 1 BLADE WIDE CP501 A3963WV2-3PD 2 2 WHITE 1 1 BLACK WHITE F501 BLACK 6.3A125V FH501 FH502 EYF-52BCY EYF-52BCY 6.3A125Vor51MS063L CP508 003P-2100 1 CP502 A1561WV2-2P 1 2.7M 1/2W +-10%
250V 0.001 KX
250V 0.001
7
TO SOUND D505 25V 2200 YK 30DF6-FC W806 R517_1 SOUND+B 0.39 3W 1SS133 P.CON+12V GND SOUND_GND D517 R503 1SS133 D514 10K 1/4W 38 R537 100K 1/4W 115.4 C510 C539 T501 8 8140066S 0.01 B 115.5 82K 1/4W 9 P1 7 10 NC 50V 2.2 R536 C517 W825 B504 220P CH R535 2KV 0.0015 R D510 160V 220 YXF R527 0.68 2W 3.9K 1/4W 47K 1/4W R507 YK 10K 1/4W R505 115.1 114.7 +B SW. Q503 2SA1371 1SS133
4 R500
C501
R501 RM11C-EIC RM11C-EIC 1 7W
R541_1 1.2M 1/4W 0.22 1W R539
D501
R540
C502 ECQUL 2KV 0.001 R RM11C-EIC D504
C503 470 UP C507 2KV 0.001 R RM11C-EIC D503
1.2M 1/4W
COIL,LINE FILTER L501 2R2A752F28Y 0.22 ECQUL
D502
D513
FROM/TO DEFLECTION H+B +B FBT+B GND
ZPB45BL3R0A
275V 0.1
AC120V_60Hz CD501_1 0R615901
6.3A 125V
275V
200V
D523
MTZJ18B
C505_1
C506_1
CURRENT DET. Q512 2SA1624 115.7
50.0 25.0 0
6 11 P2 5 159.4 SWITCHING Q502 159.4 D 2SK3326(2) G 5.3 5.3 0 S R 2KV 0.001 SWITCHING Q514 KTC3203_Y R544 270 1/4W D507 1SS133 1N4937 150 1/4W D509 2 1SS133 100 1/4W 0 13 R502 330 2W 1.5 C524 C512 100V 0.047 MMTS 500V 0.001 B 2 HS501 763WAA0244 1 16 C511 240.0 12 NC
141.6 0 40.0
115.2 STAND BY SW. Q505 2SC2909 0 0 R513
R516 10K 10K TO TUNER/STEREO P.CON+B GND
W5RH3.5X5X1.0 FE201-6L49 C521
W801
B501 BL02RN1-R62
138.9
3 14
C535
26.0 15
TO CHROMA UNREG+12V GND
R542 0.15 1W
FROM/TO MICON 2.2 YK R545 D524 D511 R546 R524 P.FAIL R525 3.3K 1/4W 15K X-RAY DEGAUSS_H POWER GND
4
10.7 1 C554 0.022 B 6.3 W817 5.7 15K 1/2W R553 9.7 FEED BACK SWITCHING Q507 KTC3198 R532 1.5K R510 100 1/4W R533 270 9.7
FEED BACK IC504 LTV-817M-VB 16.3 4
C504 C520 1K 1/2W 500V 0.001 D512 GND1 21DQ09N B
R508 100 1/4W
D506 1N4937
1.5
MTZJ18B
0.056 B
47 YK
50V P.CON+12V SW. Q508 KTA1271_Y 12.9 R511 22K R512 12.9 12.8 1K 1/2W 16V
R543_1
C541
C509
25V
C550 220 YK
3
6.8K 1/4W 100K 1/2W R506 R554
16V 2200 YK
CAUTION:
250V 0.0022 KX MTZJ6.2B D508 MTZJ5.6B
IS THE LIVE CONNECTION

C523 0.001 CH
MTZJ15B
D525
100 1/4W
+B ADJ
VR502 22K D528
R547
C508_1
0.8 STAND BY SW. Q509 KTC3198
1SS133
D520
C527
0.7 0
R519 10K
TO AV P.CON+12V GND FROM/TO COMB FILTER GND
2
PCB010 TMC559
6.3A 125V
CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, 6.3A 125V(F501)

REPLACE ONLY WITH THE SAME TYPE FUSE UNE PROTECTION CONTINUE LES RISQUES DINCEIE ATTENTION:POUR NUTILISER QUE DES FUSIBLE DE MEME TYPE 6.3A 125V(F501)
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
ARE
G-7
G-8
SOUND SCHEMATIC DIAGRAM

8
(MAIN PCB)
50V 10 YK
220K C333
R314
C315
0.1
0.015 B
C307
C319
FROM TUNER/STEREO 23 R302 0.033 B 2.7K 1/4W C301 SW_AUDIO_L 22 SW_AUDIO_R 2.7K 1/4W R301
50V 10
YK
7
0.033 B 50V 10 YK 50V 10 YK 50V 10 YK 0.01 B C310 C313 W832 C304 C309 0.039 B 3.9 3.9 6 7 PF2 PF3 C317 C321 4.0 15 16 VD L ONT Balance /MUTE
3.9 1 PF1 TONE CONTROL IC IC302 AN5891SA-E1V
1.7 2 AGC
3.0 3 L IN
NC 4 NC
NC 5 NC
3.9 8 PF4
0 9 GND
4.0 10 LT
4.0 11 LB
NC 12 NC
NC 13 NC
2.0 14 BD
2.9
AGC
SURR
Tone Control
Volume 2.2K Control
+ + NC 21 0 NC 0 NC C318 NC 20
MODE control VCC 32 2.3 7.9 31
R IN 30 4.5 C305
Vref 29 4.0 50V 10 YK 0
NC 28 0 NC
NC 27 4.0 NC
BB 26
RB RT BLD TD 25 24 23 22 4.0 4.4 3.0 2.0
R OUT SDA SCL 19 18 17 4.0 3.5 3.5 50V 10 YK
50V 10 YK
50V 10 YK
0.01 B
C312
C316
50V 10 YK
R303 100 1/4W R304
C302
C334
1 B
FROM CHROMA
C308
P.CON+8V[B] 100uH 0305 16V 100 YK C311 0.01 B C306 B
C314
L301
50V 10 YK
100
1/4W
0.1
56P CH C322
C303
C320
FROM/TO COMBI FILTER GND FROM/TO MICON SDA SCL
4
TV_MUTE SOUND AMP IC IC1001 AN17808B + + ATT. + VOL CH2 VOL MUTE OUT 6 7 8 0 0.7 3.7 STAND CH1 GND VCC -BY OUT 9 10 11 12 0.7 0 16.5 12.7 RIPPLE FILTER CH1 CH2 NC GND RF IN IN 1 2 3 4 5 0 NC 0.2 16.0 0 0.2 + ATT.CONT. 25 24 CP1001 A2502WV2-4P 4 3 2 1 W803 R1003 15K R1004 25V 2200 YK 0.0047 B R1011 C1012 R1010 12K B 15K 25V 1000 YK 25V 1000 YK C1001 50V 0.1 YK C1002 50V 0.1 YK C1009 C1004 4 3 2 1 (R) (L) SP1001_1 S0509F12-F 8 OHM 2.5W W/CONECTOR.2SPEAKER SPEAKER 8 OHM 2.5W
56P
CH
W831
FROM POWER SOUND+B
GND P.CON+12V SOUND_GND
12K C1010
W858
0.0047
R1013 10K 25V 220 YK R1009 MUTE 68K 1/4W Q1001 KRC111SRTK 3.6 0 0
C1003
W833 26 50V 0.22 YK 50V 22 YK W834 27 HS1001 763WAA0215
W835
C1011_1
220P B
C1005
C1008
C1007
PCB010 TMC559
ARE
CAUTION: DIGITAL TRANSISTOR
G-9
G-10
TUNER/STEREO SCHEMATIC DIAGRAM

8
(MAIN PCB)
TU001
19
115-V-K015AR_B 9 (ADRESS) 14 SIF OUT 8 (XTAL) 16 IF OUT AUDIO OUT VIDEO OUT
20
11 SDA
10 SCL
12 AFT
MB
MB
15 BT
13
17
FROM/TO CHROMA
21
18
7
W812
NC
NC
NC
NC
NC
NC NC
NC
NC
NC
TUNER+5V TUNER_VIDEO P.CON+8V[B]
0.1 B
C002
P.CON+5V
R006
100
100 YK
C005
C001_1
0.1 MTZJ33B D001
6
W820
6.3V
W819
FROM POWER R001 P.CON+B 68K 1/2W R002 68K 1/2W TO MICON GND
AFT
FROM/TO MICON 220 1/4W 1/4W R901 R904 SCL SDA J_AUDIO_OUT_L 1/4W 1/4W 56K
R902
3.2 2.3 BUFFER Q901 KTA1504S_Y_RTK 0
56K
C901
50V 1 KA
J_AUDIO_OUT_R R912 3.2 2.3 BUFFER Q902 0 KTA1504S_Y_RTK R906 R903 39K C902 50V 1 KA W829 39K C919 W830
220
R905
4
330 50V 10 YK
TO SOUND L901 SW_AUDIO_L 0.047 B C913 0.1 B 0.1 B SW_AUDIO_R C911 100uH 0305 C917
3
24 SOUND DECORDER IC IC902 AN5829S 2.3 23 2.3 22 2.3 21 2.3
DAC
NC 20
19
5.0
18
5.0
GND
17
16
3.7
15
3.6
14
2.6
13
Det SAP
3.7
AGC Matrix
OUT SW
ZAP IIC Decoder L-R Filter L+R Filter L-R Demod L+R Demod
St.PLL Cancel Pilot Filter Stereo
Det Pilot Filter Noise Filter Spectral
VCA Input
FROM/TO AV
J_AUDIO_OUT_L J_AUDIO_OUT_R AUDIO_IN1/2[R] AUDIO_IN1/2[L] AUDIO_IN3[R] AUDIO_IN3[L]
Switch De-Emph (L-R)/SAP 75us Filter Cancel SAPout Offset Expand Cancel Wide Band Offset
Filter SAP Demod SAP Det Noise
fH.2fH Trap Filter RMS Det Wide Band dbx De-Emph
Filter Wide Band Expand Spectral
2.3 1 0 2 2.3 3 2.3 C904 4 2.2 50V 4.7 KA 5
RMS Det Spectral
6 2.2 C907 0.4 50V 10 YK
Vcc
8 2.4 50V 0.33 KA
9 2.4 C914
10 0.4
11 2.3 C918 50V 3.3 KA
12 3.4 0.1 B
5.1 C910
2
10V 100 YK C916
50V 4.7 KA
50V 4.7 KA
0.022 B
0.022 B
C912
R907
C905
0.1 B
39K C903
C908
C915
PCB010 TMC559
ARE
G-11
G-12
AV SCHEMATIC DIAGRAM
8
FROM/TO CHROMA 28 V_IN[YUV] U_IN[YUV] Y_IN[YUV] R725 29 MTZJ12B MTZJ12B R730 MTZJ12B D701 D702 75 D703 R736 75
(MAIN PCB)
YUV_IN(REAR) J704 MSP-213V1-652_NI H1 2 1 E
H2
VIDEO_OUT VIDEO_IN2 VIDEO_IN1 VIDEO_IN3 C711 C707 R702 16V 100 YK R709 270 220 1/4W C708 16V 10 KA R704 1K MUTE Q711 KTC3875S_Y_RTK 0 R710 0.1 1K 1/4W 0.2 16V 10 KA R708 1K
75 H1
A/V_OUT(REAR) J708 MSP-213V2-432_NI

H1 NC H1 H2
C728 0.2 R711 0.1 1K 16V 470 YK MUTE Q712 KTC3875S_Y_RTK 0
68
R705
3.3K
R703 2.2K
C710 16V 47 KANP
4.6 R706 3.3K
5.2
BUFFER Q709 KTA1504S_Y_RTK
6
LINE2(REAR) J703 MSP-213V2-432_NI
H1 NC H1 H2
R721
C727 1 B C724 1 B
R734 1K R728 1K 0.0056 B C735 MTZJ12B 0.0056 B
R727
FROM/TO TUNER/STEREO
75 D705
C737
5
J_AUDIO_OUT_R J_AUDIO_OUT_L C702 AUDIO_IN1/2[R] C701 AUDIO_IN1/2[L] AUDIO_IN3[L] AUDIO_IN3[R] 16V 10 KA 16V 10 KA R701 16V 220 YK 560 1/4W C705 1 0 3.7 12.7
AUDIO SW(R) IC IC701 SW1 V.OUT Vcc MM1501XNRE Vin1 GND Vin2 6 4.5 0 4.5 C725 1 2 5 B C722 1 B R733 1K R726 1K 0.0056 B C736 MTZJ12B
LINE1(REAR) J701 MSP-213V2-432_NI

H1 NC H1 H2
C706
C733 16V 22 KA R739 75
S-JACK J702 YKF51-5503 1
4
FROM/TO MICON AUDIO SW(L) IC EXT_MUTE AUDIO_SW S_IN IC702 1 0 3.7 12.7 SW1 V.OUT Vcc MM1501XNRE Vin1 GND Vin2 6 4.5 0 4.5
0.1
0.0056 B
R729
75 D704
C738
C734 0.1 B
R735
75
2 FRONT-VIDEO J705 HTJ-032-03AY

NC
3
TO COMB FILTER
MTZJ6.2B
D709
S_VIDEO_IN[Y] S_VIDEO_IN[C] MTZJ12B R724 D706 75
FRONT-AUDIO.L J706 HTJ-032-03AW

NC
C719 1 B
R745 1K
2
FROM POWER C720 1 P.CON+12V GND B R746 1K
0.0056
FRONT-AUDIO.R J707 HTJ-032-03AR

NC
C741
LINE3_A_IN_L
C742
0.0056
LINE3_A_IN_R
PCB010 TMC559
G-13
G-14
CRT SCHEMATIC DIAGRAM

8
(CRT PCB)
CRT BLOCK (W/O SVM)

FROM DEFLECTION 2KV 0.001 B CP801B B2013H02-5P CP806_1 1 2 3 4 5 180V NC NC GND HEATER NC NC W802 C802
FROM DEFLECTION
SCREEN
R802
FROM CHROMA C805_1 CP802B B2013H02-7P 1 2 3 4 5 6 7 CLAMP GND R.OUT G.OUT B.OUT CLAMP OFF NC 1SS133 R809 4.7K GREEN/RED OUT Q803 98.4 KTC3199_Y 390P B R813 390 GREEN/RED OUT Q805 125.0 KTC4217 7.4 D802 1SS133 39 4.7K BLUE OUT Q802 KTC3199_Y 390 BLUE OUT Q806 KTC4217 7.4 R810 220 128.0 7.0 D803 1SS133 C801 100P B R824 100 1/2W TCC421 PCB110 7.0 14F:RED OUT 27":GREEN OUT 99.6 R804 1SS133 R814 390P B R816 68 R808 220 68 1SS133 37 100 (27"RED) D810 RED/GREEN OUT Q804 220 KTC4217 7.4 D801 123.0 6.9 14F:GREEN OUT 27":RED OUT R806 38
FOCUS
R803 12K 2W
2.7K 1/4W
R812
RED/GREEN OUT Q801 100.6 KTC3199_Y
0.1
3.2 2.7
C811 R817
R801
R807 12K 2W
2.7K 1/4W
R820 100 (27"GREEN) D811
2.7
96.4
3.2
96.4 8
C810
R818
0 9 6.4 10 11 12 NC 1 CP803 2 A2361WV2-2P 96.4 FROM BRAIDED WIRE
7 6 5
R805 12K 2W
2.7K 1/4W 0 0
R821
95.4 2.7
C809 390P B R815 390 R819 68
1
0
100 D812 1SS133
3.2
F CRT SOCKET J801_1 ISHS53S
R811 4.7K
ARE
G-15
G-16
COMB/FILTER SCHEMATIC DIAGRAM

8
(MAIN PCB)
L1511 15uH 0305 16V 100 YK
7.9 2.5 2.0
6
L1505 R1530 15uH 0305 R1503 R1505 6.8K 270
0.01 B
C1528
C1531
C1535 16V 10 KA 470 FROM AV S_VIDEO_IN[C] R1512 W848 BUFFER Q1503 KTC3875S_Y_RTK 470 S_VIDEO_IN[Y]
6.3V 100 YK
C1510
0.01 B
C1509
C1513 0.1 B
5.0 1.0 1.0
C1519 100P CH C1517 R1506 R1507 3.3K 0.1 1K B 4.5 0 4.5
VIDEO SW(Y) IC IC1502 Vin1 GND Vin2 6 MM1501XNRE SW1 V.OUT Vcc 1 0 4.4 7.9
FROM MICON Y/C_SW
4
C1504 0.1 B R1502 COMB FILTER IC IC1501 LA76605M-TLM 2.6 2.4 CIN COUT 18 1 4.9 INSEL YIN2 GND AVCC DVCC SAND CASTLE OUTSEL YOUT GND YIN1 AFC RD 2 4.2 3 0 4 4.9 5 4.9 6 C1502 6.3V 100 YK C1503 0.1 B C1506 4.0 0.1 B C1507 2.1 PHASE DET FSC_IN GND GND 8 0.1 B 0 9 7 0 17 3.4
VIDEO SW(C) IC IC1503 MM1501XNRE 0 4.5 Vin1 SW1 6 1 5 2 0 4.5 GND Vin2 V.OUT Vcc 4.4 7.9 16V 100 YK L1501
FROM/TO CHROMA
Y_V_OUT_SW C_V_OUT_SW P.CON+8V[A] 100uH 0305 C1523 C1532 F 0.1
100
C1505 1 B
15
16
0 C1514 R1528 0.1 B L1508 R1529 C1521 0.1 B R1509 6.3V 100 YK 2.9 14 3.6 13
C1501
6.3V 100 YK
C1508
L1502
0.1 B
P.CON+5V 15uH 0305 100uH 47K C1520 0305 L1510
220uH 0305
L1503 220uH 0305
12
82K C1516 2.7K R1504 C1518 0.1 B 9.5 C1512 8.2K 50V 1 KA 0.9 0.1 B C1515 0.1 B
5.0 2.4 BUFFER Q1504 KTC3875S_Y_RTK 2.0 R1508 3.9K
R1523 100 R1510
FSC_OUT
11
R1518 5.0 2.2 1.6 R1519
0 10
6.3V 100 YK
47K
0.01 B
C1525
C1526
27K C1530_1 16V 47 KA R1520 C1533 22P CH 1.2K
L1512 22uH
R1522 VIDEO_OUT 1K
R1516
24K
1K
FROM/TO POWER GND
FROM/TO SOUND
GND
PCB010 TMC559
G-17
G-18
MICON
WAVEFORMS
1 1V 0.1 s/div
0.5V 10ms/div
13 1V 20 s/div
2 1V 1 s/div
9 1V 50 s/div
14 2V 20 s/div
3 1V 50 s/div
10 2V 20 s/div
15 2V 20 s/div
DEFLECTION
4 1V 0.1ms/div
11 0.5V 20 s/div
16 2V 5ms/div
CHROMA
7 1V 20 s/div
12 1V 2 s/div
17 20V 5ms/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-1
WAVEFORMS
18 10V 10ms/div
38 50V 20 s/div
25 2V 5ms/div
19 20V 20 s/div
39 50V 20 s/div
26 5V 2ms/div
SOUND
20 2V 20 s/div
22 2V 5ms/div
27 5V 2ms/div
AV
21 200V 50 s/div
23 2V 5ms/div
28 200mV 20 s/div
CRT
37 50V 20 s/div
24 2V 5ms/div
29 200mV 20 s/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-2
MECHANICAL EXPLODED VIEW

201 107 102C 201 201 201 203 109 202 109 121 102A 106 202 PCB110 (CRT PCB ASS'Y) 102B 201 102B 201
102
201
202 121 109
121
202
110 206 121 109 204
203
204 105
103 206
203
104 101G 205 101G
203 108
101G 101F 203 101D
PCB010 (MAIN PCB ASS'Y)
101B 101E 101C 101A
101
I-1
MECHANICAL EXPLODED VIEW (PACKING DIAGRAM)
118, 119, 120, TM101
113
112
115
116
114
114 111
I-2
MECHANICAL REPLACEMENT PARTS LIST (FOR USA)

Location No. TSB P/N
101 101A 101B 101C 101D 101E 101F 101G 102 102A 102B 102C 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 201 202 203 204 205 206 AE004100 AE004101 AD301618 AE004102 AD301620 AE004103 AE004104 AE003071 AE004105 AE004106 AE003021 AE004107 AD301616 AE004293 AE003190 BZ710660 AE004108 AD301624 AD300768 BZ710260 AE004109 AD300432 AD301626 AD301627 AE004110 AE000232 AE004111 AE003390 AD300022 AE004112 AE000412 BZ710036 AD301625 BZ710031 BZ710239 BZ710019 BZ710018
Reference No.
A3N426N720 701WPJC545 711WPAA088 712WPBA084 713WPAA090 723549A034 735WPBA983 800WQ0A041 A3N426N740 702WPAA386 800WQ0A072 800WQ0A076 761WPA0263 800WQ0A066 800WQ0A067 741WUA0021 722549A312 724000A002 762WPA0009 899HV3T000 723000C517 791WHA0092 792WHA0416 792WHA0417 793WCDC090 795WCA0665 A3N426N975 JA4UD200 J3I70417 J3N42601A 769WSAA005 8117540B04 8141J50D54 8110630A04 8109I30A04 8109630802 8107630804
Description
CABINET,FRONT ASSY CABINET,FRONT PLATE,FRONT DOOR GLASS,LED AV LABEL BUTTON ASS'Y FELT SHEET CABINET,BACK ASSY CABINET,BACK FELT SHEET FELT SHEET HOLDER,JACK FELT SHEET FELT SHEET SPRING,EARTH SHEET,RATING SHEET,CSA HOLDER,CRT WIRE HOLDER,ANODE WIRE SHEET,BAR CODE LAMIFILM,BAG PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX PAD 378x1114 INSTRUCTION BOOK KIT POLYBAG,INSTRUCTION(RED CAUTION) REGISTRATION CARD INSTRUCTION BOOK WASHER CRT T=1 SCREW,TAPPING(B0) TRUSS SCREW,TAP TITE(P) GW20 SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(B) WH7 SCREW,TAP TITE(B) BRAZIER SCREW,TAP TITE(S) BRAZIER 4x20 5x45 3x10 3x10 3x8 3x8
J1-1
MECHANICAL REPLACEMENT PARTS LIST (FOR CANADA)

Location No. TSB P/N
101 101A 101B 101C 101D 101E 101F 101G 102 102A 102B 102C 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 201 202 203 204 205 206 AE004100 AE004101 AD301618 AE004102 AD301620 AE004103 AE004104 AE003071 AE004105 AE004106 AE003021 AE004107 AD301616 AE004293 AE003190 BZ710660 AE004108 AD301624 AD300768 BZ710260 AE004109 AD300432 AD301626 AD301627 AE004110 AE000232 AE004111 AE003390 AD300022 AE004112 AE000053 BZ710036 AD301625 BZ710031 BZ710239 BZ710019 BZ710018
Reference No.
A3N426N720 701WPJC545 711WPAA088 712WPBA084 713WPAA090 723549A034 735WPBA983 800WQ0A041 A3N426N740 702WPAA386 800WQ0A072 800WQ0A076 761WPA0263 800WQ0A066 800WQ0A067 741WUA0021 722549A312 724000A002 762WPA0009 899HV3T000 723000C517 791WHA0092 792WHA0416 792WHA0417 793WCDC090 795WCA0665 A3N426N975 JA4UD200 J3I70417 J3N42601A 800WR0A011 8117540B04 8141J50D54 8110630A04 8109I30A04 8109630802 8107630804
Description
CABINET,FRONT ASSY CABINET,FRONT PLATE,FRONT DOOR GLASS,LED AV LABEL BUTTON ASS'Y FELT SHEET CABINET,BACK ASSY CABINET,BACK FELT SHEET FELT SHEET HOLDER,JACK FELT SHEET FELT SHEET SPRING,EARTH SHEET,RATING SHEET,CSA HOLDER,CRT WIRE HOLDER,ANODE WIRE SHEET,BAR CODE LAMIFILM,BAG PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX PAD 378x1114 INSTRUCTION BOOK KIT POLYBAG,INSTRUCTION(RED CAUTION) REGISTRATION CARD INSTRUCTION BOOK SHEET CRT SUPPORT (D) SCREW,TAPPING(B0) TRUSS SCREW,TAP TITE(P) GW20 SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(B) WH7 SCREW,TAP TITE(B) BRAZIER SCREW,TAP TITE(S) BRAZIER 4x20 5x45 3x10 3x10 3x8 3x8
J1-2
ELECTRICAL REPLACEMENT PARTS LIST

Location No.
! R410 R419 ! R426 ! R434 ! R436 ! R438 ! R439 ! R441 ! R452 ! R459 ! R500 ! R501 ! R502 ! R506 ! R517 ! R520 ! R527 ! R541 ! R542 ! R602 ! R649 ! R803 ! R805 ! R807 C408 C412 C413 C418 C420 C421 C425 C426 C430 C442 C501 C502 C503 C505 C506 C507 C508 C513 C517 C519 C521 C527 C535 C646 C802 C1003 C1004 C1009
TSB P/N
AD302107 AD300784 BZ210030 BZ210259 BZ210023 BZ210022 BZ210003 BZ210231 AD301385 AD301595 BZ210080 AD301596 BZ210249 BZ210162 AD302108 BZ210206 BZ210149 BZ210190 BZ210248 AD301975 AD301975 BZ210050 BZ210050 BZ210050 BZ110032 AD301599 AD301977 AE001019 AD300723 AD301600 BZ110182 BZ110225 BZ110195 AD301601 BZ210176 BZ110182 BZ110182 BZ110025 BZ110035 BZ110012 BZ110222 AD301026 BZ110191 AD301026 BZ110228 BZ110119 BZ110182 AD301321 BZ110247 BZ210176 BZ110053 BZ110053 BZ410037 BZ410006 BZ410006 BZ410020 BZ410054 BZ410021 BZ410043 BZ410019 BZ410020 BZ410063 BZ410021 BZ410063 AD302110 AD301980 BZ410019 BZ410063 BZ410043
Reference No. RESISTORS

R3X18A470J R3X1811R2J R4X5T4472F R5Y2CF1R8J R4X5T4183F R6558A1R2J R3K181102J R4X5T6153F R3X18A391J R65582010J R0G3K2275K R5X2AE010J R3X28A331J R002T4682J R3X28BR39J R002T2155J R3X18AR68J R63581R22J R3X181R15J R3X28B120J R3X28B120J R3X18A123J R3X18A123J R3X18A123J E5EZF3102M P4N8FJ272H E0ELF4102M P4J7F3434J P4N8FJ153H P3N1F5223J C03L0R713K E5EZFD220M E02LU8220M E53FF56R8M E02LF3222M C03L0R713K C03L0R713K P2122B224M P2122B104M E51CGC471M CD39E0MH3M CD39E0M13M C03L0R7E3K CD39E0M13M E62NFB221M E02LF2222M C03L0R713K CQG0CH412J C0JBB0713K E02LF3222M E02LF3102M E02LF3102M D97U03301B D1VT001330 D1VT001330 D97U05R11B 0021721150 D97U05R61B D2WT011E10 D97U03001B D97U05R11B D2WTAU02A0 D97U05R61B D2WTAU02A0 D2CF0715L0 D2CF2016L0 D97U03001B D2WTAU02A0 D2WT011E10 R,METAL OXIDE R,METAL OXIDE R,METAL R,CEMENT R,METAL R,FUSE R,METAL R,METAL R,METAL OXIDE R,FUSE RC R,CEMENT R,METAL OXIDE RC R,METAL OXIDE RC R,METAL OXIDE R,FUSE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE CE CMPP CE CMPP CMPP CPP CC CE CE CE CE CC CC CMP CMP CE CC CC CC CC CE CE CC CC CC CE CE CE
Description
47 OHM 2W 1.2 OHM 1W 4.7K OHM 1/4W 1.8 OHM 10W 18K OHM 1/4W 1.2 OHM 2W 1K OHM 1W 15K OHM 1/6W 390 OHM 2W 1 OHM 1/2W 2.7M OHM 1/2W 1 OHM 7W 330 OHM 2W 6.8K OHM 1/4W 0.39 OHM 3W 1.5M OHM 1/2W 0.68 OHM 2W 0.22 OHM 1W 0.15 OHM 1W 12 OHM 3W 12 OHM 3W 12K OHM 2W 12K OHM 2W 12K OHM 2W 1000 UF 25V 0.0027UF 1.25KV 1000 UF 35V 0.43 UF 250V PMS 0.015 UF 1.25KV 0.022 UF 630V 0.001 UF 2KV R 22 UF 250V 22 UF 100V 6.8 UF 50V NP 2200 UF 25V 0.001 UF 2KV R 0.001 UF 2KV R 0.22 UF 275V ECQUL 0.1 UF 275V ECQUL 470 UF 200V 0.0022UF 250V 0.001 UF 250V 0.0015UF 2KV R 0.001 UF 250V 220 UF 160V 2200 UF 16V 0.001 UF 2KV R 100 PF 50V CH 0.001 UF 2KV B 2200 UF 25V 1000 UF 25V 1000 UF 25V MTZJ33B T-77 1SS133T-77 1SS133T-77 MTZJ5.1B T-77 SLR-342VCT32 MTZJ5.6B T-77 11E1-EIC MTZJ30B T-77 MTZJ5.1B T-77 AU02A-EIC MTZJ5.6B T-77 AU02A-EIC ERD07-15L50 FE201-6L49 MTZJ30B T-77 AU02A-EIC 11E1-EIC
CAPACITORS
!
! ! ! ! !
DIODES
D001 D104 D105 D106 D109 D113 D402 D403 D404 D405 ! D406 D407 D408 D409 D410 ! D411 D414 DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,ZENER LED DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON
J2-1

Location No.
D415 D416 D417 D419 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D514 D516 D517 D520 D523 D524 D525 D528 D601 D602 D603 D604 D605 D606 D607 D608 D701 D702 D703 D704 D705 D706 D709 D801 D802 D803 D810 D811 D812
TSB P/N
BZ410043 BZ410006 BZ410006 BZ410006 BZ410062 BZ410062 BZ410062 BZ410062 BZ410111 AD300731 BZ410006 BZ410066 AD300671 AD301980 AD300731 BZ410010 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 AD300671 BZ410006 BZ410094 BZ410021 BZ410006 BZ410058 BZ410094 AD300070 BZ410006 BZ410006 BZ410006 BZ410043 AD300070 AD300070 AD300070 AD300070 AD300070 AD300070 BZ410066 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 AD301981 AD302111 AD301983 BZ611117 BZ410088 AE002803 AD301988 AD301988 BZ611068 AE003081 AE003002 AD301988 AD301988 BZ510109 BZ510109 BZ510097 BZ510040 BZ510073 BZ510073 BZ510110 BZ510109 BZ510098 BZ510005
Reference No. DIODES

D2WT011E10 D1VT001330 D1VT001330 D1VT001330 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D28F30DF60 D2WXN49370 D1VT001330 D97U06R21B D97U01801B D2CF2016L0 D2WXN49370 D28T21DQN9 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D97U01801B D1VT001330 D97U01501B D97U05R61B D1VT001330 D97U08R21B D97U01501B D97U01201B D1VT001330 D1VT001330 D1VT001330 D2WT011E10 D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U06R21B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 I56F07090A A3N402M015 I01FF58910 I03TD80410 0002E00610 I06FC1283A I0UF015010 I0UF015010 I01FF58290 I0FSP7808B I03FE76605 I0UF015010 I0UF015010 TCAA3875SY TCAA3875SY TCAT03227Y TDUU024990 TAATA12660 TAATA12660 TC30041590 TCAA3875SY T220033260 TA3T1371A0 DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,RECTIFIER DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON
Description
11E1-EIC 1SS133T-77 1SS133T-77 1SS133T-77 RM11C-EIC RM11C-EIC RM11C-EIC RM11C-EIC 30DF6-FC 1N4937 1SS133T-77 MTZJ6.2B T-77 MTZJ18B T-77 FE201-6L49 1N4937 21DQ09N-TA2B1 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ18B T-77 1SS133T-77 MTZJ15B T-77 MTZJ5.6B T-77 1SS133T-77 MTZJ8.2B T-77 MTZJ15B T-77 MTZJ12B T-77 1SS133T-77 1SS133T-77 1SS133T-77 11E1-EIC MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ6.2B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 OEC7090A AN5891SA-E1V LA78041 LTV-817M-VB M61283FP R70T MM1501XNRE MM1501XNRE AN5829S AN17808B LA76605M-TLM MM1501XNRE MM1501XNRE KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3227_Y-AT 2SD2499(LB0EC1) KTA1266-AT(Y,GR) KTA1266-AT(Y,GR) 2SC4159(D,E) KTC3875S_Y_RTK 2SK3326(2) 2SA1371(D,E)-AE
! ! ! !
ICS
IC101 IC199 IC302 IC401 ! IC504 IC601 IC701 IC702 IC902 ! IC1001 IC1501 IC1502 IC1503 Q101 Q103 Q402 Q405 Q408 Q409 Q410 Q411 Q502 Q503 IC INIT DATA IC IC PHOTO COUPLER IC IC IC IC IC IC IC IC TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON FET TRANSISTOR,SILICON
TRANSISTORS
J2-2

Location No.
Q504 Q505 Q507 Q508 Q509 Q512 Q514 Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q611 Q614 Q709 Q711 Q712 Q801 Q802 Q803 Q804 Q805 Q806 Q901 Q902 Q1001 Q1503 Q1504 Q1507 Q1508
TSB P/N
BZ510069 BZ510011 BZ510069 BZ510077 BZ510069 BZ510004 BZ510070 BZ510105 BZ510105 BZ510109 BZ510105 BZ510109 BZ510105 BZ510070 BZ510105 BZ510108 BZ510108 BZ510109 BZ510109 BZ510100 BZ510100 BZ510100 BZ510091 BZ510091 BZ510091 BZ510108 BZ510108 BZ510068 BZ510109 BZ510109 BZ510109 BZ510109 BZ310041 BZ310187 AD301606 AD301124 AD301607 BZ310041 BZ310041 AD301417 AD301417 AD300613 BZ310041 AD300613 AD300613 AD301608 BZ310189 AD301034 AD301038 AD300108 AD301038 AD301037 AD300110 AD300111 AD300112 AD301038 AD301356 BZ612010 BZ612010 BZ612010 BZ612010 BZ612010 BZ210218 BZ210101 AE004113 AE003346
Reference No. TRANSISTORS

TCATC31980 TC3T029090 TCATC31980 TAAT012714 TCATC31980 TA3T016240 TCAT032034 TCAT03209Y TCAT03209Y TCAA3875SY TCAT03209Y TCAA3875SY TCAT03209Y TCAT032034 TCAT03209Y TAAA1504SY TAAA1504SY TCAA3875SY TCAA3875SY TCATC3199Y TCATC3199Y TCATC3199Y TCA0042170 TCA0042170 TCA0042170 TAAA1504SY TAAA1504SY TNAAJ05003 TCAA3875SY TCAA3875SY TCAA3875SY TCAA3875SY 02167F101J 022100034A 02DK000058 029T000101 028R270010 02167F101J 02167F101J 02167F221J 02167F221J 02167F150J 02167F101J 02167F150J 02167F150J 0216A6220J 0450190161 048140066S 060J431019 063Q700002 060J431019 060J411024 060G401047 060G401046 060G401039 060J431019 066F130020 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 V1K63H3BTE V1163H4BTC A3N426N010 A3N425N110
Description
KTC3198-AT(Y,GR) 2SC2909(S,T)-AA KTC3198-AT(Y,GR) KTA1271_Y-AT KTC3198-AT(Y,GR) 2SA1624-AA KTC3203_Y-AT KTC3209_Y-AT KTC3209_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3203_Y-AT KTC3209_Y-AT KTA1504S_Y_RTK KTA1504S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3199_Y-AT KTC3199_Y-AT KTC3199_Y-AT KTC4217(O,Y) KTC4217(O,Y) KTC4217(O,Y) KTA1504S_Y_RTK KTA1504S_Y_RTK KRC111SRTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK 100 UH ELH5L4132N 02DK000058 2R2A752F28Y 8R270010 100 UH 100 UH 220 UH 220 UH 15 UH 100 UH 15 UH 15 UH 22 UH ETH19Y203AY 8140066S MSP-213V2-432 PBSN YKF51-5503 MSP-213V2-432 PBSN MSP-213V1-652 PBSN HTJ-032-03AY HTJ-032-03AW HTJ-032-03AR MSP-213V2-432 PBSN ISHS53S EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R NVG6TLTAB222 EVNCYAA03BE4 TMC559D TCC421D
! ! ! ! ! !
TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COIL COIL,LINEARITY COIL,CHOKE COIL,LINE FILTER COIL,DEGAUSS COIL COIL COIL COIL COIL COIL COIL COIL COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING
COILS &TRANSFORMERS
L301 L402 L403 ! L501 ! L503 L901 L1501 L1502 L1503 L1505 L1508 L1510 L1511 L1512 T401 ! T501 J701 J702 J703 J704 J705 J706 J707 J708 ! J801 SW101 SW102 SW103 SW104 SW105 VR401 VR502 PCB010 PCB110
JACKS
RCA JACK JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY,TUBE
SWITCHES
SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT VOLUME,SEMI FIXED VOLUME,SEMI FIXED PCB ASS'Y PCB ASS'Y
VARIABLE RESISTORS P.C.BOARD ASSEMBLIES
J2-3

Location No.
B403 B405 B501 B504 BT001 BT002 CD501 CD801 CD802 CD803 CP101 CP401 CP501 CP502 CP507 CP508 CP803 CP1001 CP801A CP801B CP802A CP802B EL001 EL002 F501 FB401 FH501 FH502 OS101 RY501 SP1001 TH501 TM101 TU001 V801 X101 X602 RESISTOR RC................... CAPACITORS CC................... CERAMIC CAPACITOR CE................... ALUMI ELECTROLYTIC CAPACITOR CP................... POLYESTER CAPACITOR CPP.................. POLYPROPYLENE CAPACITOR CPL.................. PLASTIC CAPACITOR CMP....................... METAL POLYESTER CAPACITOR CMPL................ METAL PLASTIC CAPACITOR CMPP................ METAL POLYPROPYLENE CAPACITOR CARBON RESISTOR
TSB P/N
BZ310129 BZ310129 BZ310045 BZ310121 AE000012 AE000012 AD300746 BZ614385 AD302116 BZ614378 BZ614102 BZ614240 BZ614176 BZ614283 BZ614016 BZ614016 BZ614269 AD301045 BZ614276 BZ614276 AD301997 AD301997 BZ614044 BZ614043 BZ614422 AE003347 AE002634 AE002634 AD301048 BZ612009 AD301613 BZ410079 AE000622 AE000273 AD301614 AD302002 BZ613004
Reference No. MISCELLANEOUS

024HT03564 024HT03564 024AT03481 024HT03553 1412004008 1412004008 120R615901 WCL6838038 WEL6852038 06CU823001 0694270139 069X460029 069S320419 069S420110 069W01001A 069W01001A 069S320010 069S140419 067U005049 067U005049 067U007029 067U007029 124120301A 124116281A 081PC6R305 043227016F 06710T0009 06710T0009 0773071001 0560V20115 070Y435007 DF5EL3R0A0 076R0GW010 0163300005 0981270B01 100CT8R005 100CT3R505
Description
W4BRH3.5X6X1.0 W4BRH3.5X6X1.0 BL02RN1-R62T2 W5RH3.5X5X1.0 R03(AB)E_2P_G R03(AB)E_2P_G 0R615901 WG26 5C GRAY 380MM WG26 7C GRAY 520MM CU823001 173979-7 B06B-DVS A3963WV2-3PD A1561WV2-2P 003P-2100 003P-2100 A2361WV2-2P A2502WV2-4P B2013H02-5P B2013H02-5P B2013H02-7P B2013H02-7P XRY20X30BD XRY16X28BD 51MS063L FJN27A003_M EYF-52BCY EYF-52BCY RPM7138-WH5 ALKS321 S0509F12-F ZPB45BL3R0A R25-1939 115-V-K015AR_B M68LWF088X HC-49/U-S HC-49/C
! !
! ! ! !
CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS BATTERY,MANGAN BATTERY,MANGAN CORD,AC BUSH FLAT CABLE AWM2468 A FLAT CABLE AWM2468 A CORD,CONNECTOR CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER WIRE HOLDER WIRE HOLDER EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY SPEAKER DEGAUSS ELEMENT TRANSMITTER RF UNIT CRT W/DY CRYSTAL CRYSTAL
J2-4
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN

Toshiba 27a44 Service Manual

Uploaded by

Copyright:

Available Formats

Toshiba 27a44 Service Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Toshiba 27a44 Service Manual

Uploaded by

Copyright:

Available Formats

FILE NO.

DOCUMENT CREATED IN JAPAN, Mar., 2004

SERVICING NOTICES ON CHECKING

2. AVOID AN ELECTRIC SHOCK

3. USE THE DESIGNATED PARTS

7. PERFORM A SAFETY CHECK AFTER SERVICING

5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE

External exposure metal: Antenna terminal Earphone jack

HOW TO ORDER PARTS

CRT Support Alligator Clip Fig. 1-4

GND on the CRT

CRT CRT Support Fig. 1-2

Support Fig. 1-5

Masking Tape (Cotton Tape)

Blower type IC desoldering machine

Braided Shield Wire

Thin-tip Soldering Iron

Supply soldering from upper position to lower position

Braided Shield Wire

Fig. 2-7 B2-2

SERVICE MODE LIST

VOL. (-) MIN

CONFIRMATION OF HOURS USED

WHEN REPLACING EEPROM (MEMORY) IC

Fig. 1-2 D-1

"A" Fig. 2-2

red 120% Fig. 2-3

R G B UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT Fig. 3-2-a

WEDGE WEDGE POSITION Fig. 3-2-b

PURITY MAGNETS 6 POLE MAGNETS 4 POLE MAGNETS Fig. 3-1

CD801 CRT CD802

CP801A CP101 TU001

FB401 CP401 VR401 TP003 W003

CP501 CP1001 J707

CD501 CP802A CP502 L503 CRT J705 J706

CHROMA IC IC601 M61283FP R70T

SOUND AMP IC IC1001 AN17808B

AUDIO 3 AUDIO 1/2

COMB FILTER IC IC1501 LA76605M-TLM

TONE CONTROL IC IC302 AN5891SA-E1V

FEED BACK 1 V.OUTPUT IC IC401 LA78041 5 DY

H. OUT Q402 Q405

D524 R545 R543_1

PRINTED CIRCUIT BOARDS MAIN/CRT (INSERTED PARTS)

C527 C501 C504 W042 W043 C523 W806 W056

R536 C539 R512 R503 Q508

W052 W054 C122

W823 W020 B405

D113 W053 X101_1 R146

R419 R457 R517_1

W114 W099 W111 W113 W098 W083

D105 W116 W104 W109 W101 W102

W064 D703 W058 D702 W061

C638 C627 C618

W082 C642 C646 C611

C302 C333 R301 W141 R601 C305 C308 J706

C701 C702 W819 W820 D709 C001_1 W812 D001

C1009 HS1001 IC1001

W165 C321 C318