Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
532 views2 pages

Toe-Nailing For Uplift Reactions: 1. Proper Installation of Toe-Nails 3. Type of Nails

Uploaded by

odioslave

Wood connections

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt

Toe-Nailing For Uplift Reactions: 1. Proper Installation of Toe-Nails 3. Type of Nails

Uploaded by

odioslave
532 views2 pages
Wood connections

Original Title

t Tb Toe Nailing

Copyright

© © All Rights Reserved

Available Formats

PDF, TXT or read online from Scribd

Did you find this document useful?

Is this content inappropriate?

Wood connections

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
532 views2 pages

Toe-Nailing For Uplift Reactions: 1. Proper Installation of Toe-Nails 3. Type of Nails

Uploaded by

odioslave
Wood connections

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 2

Wood trusses are commonly attached

to the top plates of bearing walls using


a toe-nailing detail like the one shown
to the right. Is this toe-nailed connection
suffcient? It depends, the uplift resistance
of toe-nailed connections is governed by
three factors:
Conditions like wind loads or
cantilevers can produce uplift
reactions at truss bearing
supports. When this is the
case, the truss-to-bearing
connection is required to
resist the uplift reaction.
Toe-Nailing for Uplift Reactions
Copyright 2002, 2003 Wood Truss Council of America, Inc. All Rights Reserved. TTBTOENAILING-030601
1. PROPER INSTALLATION OF TOE-NAILS
To get the most out of a toe-nailed
connection, it is important to toe-
nail correctly. The fgure to the right
illustrates proper toe-nailing. The
dimensions shown are only meant to
serve as a rough guide. Toe-nail-
ing through truss plates does not
affect the uplift capacity of
the connection provided the
truss plate is not damaged
during installation.
2. GRADE & SPECIES OF TOP PLATE LUMBER
The grade and species
of the top plate also
affect the amount of uplift
resistance obtained from
a toe-nailed connection.
For example, a toe-nailed
connection using a
Southern Pine top plate will
provide greater resistance than
the same connection using
a Spruce-Pine-Fir top plate.
Graphic printed from the NDS

with permission of the AF&PA.


3. TYPE OF NAILS
The type of nail used in a toe-nailed connection
also infuences its uplift capacity. Some typical nails
are show below. When installing toe-nails, use care
to avoid splitting the bottom chord lumber. The
Building Designer should provide nail spacing and
minimum end and edge distances. In lieu of such
guidance, a rule-of-thumb is to limit the total number
of toe-nails to three for a 2x4 top plate and fve for
2x6 top plate.
Above graphic printed with permission from Simpson Strong Tie Company.
2.5" Spiral
10d
3" Spiral
16d Sinker
16d Common
3.5" Spiral
Minimum 1" spacing
between nails on the
same face.
IS TOE-NAILING ENOUGH?
Use this table to estimate the uplift capacity of a toe-nailed connection. For example, three 16d common nails toe-
nailed into a Southern Pine top plate will provide 216 lb (3 x 72 lb) of nominal uplift resistance. For wind load cases,
multiply the nominal uplift by the wind load duration factor as described in footnote 1 of the table. This factored uplift
resistance for the toe-nailed connection must be equal to or greater than the uplift reaction listed on the Truss Design
Drawing. See Sample Truss Design Drawing.
Wood Truss Council of America
One WTCA Center
6300 Enterprise Lane Madison, WI 53719
608/274-4849 608/274-3329 fax
www.woodtruss.com wtca@woodtruss.com
Copyright 2002, 2003 Wood Truss Council of America, Inc. All Rights Reserved.
Reproduction of this document, in any form, is prohibited without written permission from WTCA. This document should appear in more than one color.
An informational series designed to address
the issues and questions faced by professionals
in the building construction process.
Under industry guidelines, trusses that have been feld altered on the jobsite or overloaded during the installation phase of construction may null
or void your truss manufacturer's limited warranty. Check your truss manufacturer's limited warranty for specifc information.
NOMINAL UPLIFT CAPACITY PER TOE-NAIL
VALUES FOR TOP PLATE SPECIES
NAIL TYPE SP* DF-L* HF* S-P-F*
16d Common (0.162" x 3.5") 72.0 56.7 38.9 36.7
16d Box (0.135" x 3.5") 60.0 47.3 32.4 30.6
12d Common (0.148" x 3.25") 61.1 48.1 33.0 31.1
12d Box (0.128" x 3.25") 52.8 41.6 28.5 26.9
1. Nominal design values shall be multiplied by all applicable adjustment factors to determine allowable design
values per NDS

.
2. Uplift capacities for pneumatically driven nails are similar to box nails of the same length and diameter.
3. For nail capacities not shown here, consult a design professional.
4. Values are based on the species of the top plate or the lesser of the species.
*SP: Southern Pine *DF-L: Douglas Fir Larch *HF: Hemlock-Fir *S-P-F: Spruce-Pine-Fir
ANYTRUSS USA
5) Provide mechanical connection (by others)
of truss to bearing plate with minimum
uplift capacity of 459 lbs. at joints 1 & 9.
5) Provide mechanical connection (by others)
of truss to bearing plate with minimum
uplift capacity of 459 lbs. at joints 1 & 9.
SAMPLE TRUSS DESIGN DRAWING
MECHANICAL UPLIFT CONNECTIONS
If the toe-nail uplift resistance is less than the uplift reaction on the Truss Design Drawing, it is necessary to use a
mechanical uplift connection like those shown here.

You might also like