ARCHIVE

WELDING
SAFETY
DEPARTMENT OF LABOUR - NEW ZEALAND
 ARCHIVE

Important Note:
All the publications in the Archive contain
the best guidance available at the time of
publishing. However, you should consider
the effect of any changes to the law since
then. You should also check that the
Standards referred to are still current.

Published by the Department of Labour

PO Box 3075
Wellington
New Zealand
www.osh.dol.govt.nz

First published: 1982

Revised: 1987

2
 ARCHIVE
Foreword

THIS BOOKLET was produced by the New Zealand Department of

Labour as part of its continuing drive to reduce the incidence and
severity of industrial accidents.
It is not a technical guide or a recommendation to use particular
brands of clothing or equipment.
It is a guide to safe work methods and practices wherever welding
and gas-cutting are performed in the industrial environment. It should be
closely studied by employers and workers, tradespeople, apprentices, and
anyone who has to use welding or gas-cutting equipment in a factory or
workshop, on a building site, or in any other workplace.
It is the responsibility of employers to ensure that all operators are
adequately trained, and that they know, understand and use the correct
operating techniques.
Equally, it is the responsibility of every operator to use only the
correct operating techniques.
Information in this booklet conforms with NZS 4781:1973 Code of
practice for safety in welding and cutting. As this booklet is a general
guide, the code of practice should be referred to when more specific
information is required on any point.

3
 ARCHIVE
Contents

Foreword .................................................................................................. 3
PART 1—GAS WELDING AND CUTTING
Storage and handling of cylinders ........................................................... 9
Gases used in welding and cutting ........................................................ 10
Assembly of equipment ......................................................................... 11
Flashbacks: the causes and cure ............................................................ 12
Sequence for lighting up ........................................................................ 14
Sequence for shutting down .................................................................. 15
General safety rules ............................................................................... 16
Hazards and how to avoid them ............................................................ 17
Repair of petrol tanks etc. ...................................................................... 19
PART 2 — ELECTRIC WELDING
Arc welding machines ........................................................................... 22
Equipment checklist for operators ......................................................... 23
General safety rules ............................................................................... 24
Hazards and how to avoid them ............................................................ 25
PART 3 — FURTHER SAFETY REQUIREMENTS
Training of gas/electric welders............................................................. 28
Overalls and protective clothing ............................................................ 29
Protective equipment ............................................................................. 30
Fire protection and extinguishers .......................................................... 31
Work in confined spaces ........................................................................ 34
Ventilation systems ................................................................................ 35
New Zealand Standards ......................................................................... 40
APPENDICES
Special cutting and welding systems ..................................................... 41
Welding terminology ............................................................................. 44
 GAS WELDING AND CUTTING EQUIPMENT
ARCHIVE

Fig. 1 A typical portable gas plant, with the cylinders securely mounted on
a robust, rubber-tyred trolley for easy movement. A flashback arrestor is
fitted to each regulator. The welder is wearing suitable goggles, overalls
and safety shoes. The cylinder key is left fitted to the oxygen cylinder.

6
 ARCHIVE

Fig.2 A typical set-up showing oxygen cylinder, cylinder valve, regulator

with gauges and a flashback arrestor.

Fig.4 A suitable flashback arrestor for

use with portable trolley-mounted gas
plants or individual pipeline outlets.
There are also other suitable models
and types to protect branch lines, ring
mains, manifold and storage cylinders.
Some include a temperature cut-off
Fig.3 Outlet valves, showing left- valve which is activated by an external
hand and right-hand threads. fire. Reputable equipment suppliers will
be able to recommend particular models
for particular situations
7
 ARCHIVE

Fig. 5 A MIG (Metal Inert Gas) welding plant. The gas cylinder is not
shown, but stands behind the wire feed unit. The complexity of the unit can
be seen, and it is suitable for use only by experienced workers.

8
PART I — GAS WELDING AND CUTTING
ARCHIVE
Storage and handling of cylinders

CYLINDERS CONTAINING compressed oxygen or fuel gases are

labelled with their contents on the shoulder of the cylinder.
Although the cylinders are also colour coded, the label is the
primary identification of the contents. Do not use an unlabelled
cylinder— return it to the supplier.
Here are the general rules for the safe storage and handling of
cylinders:
(a) Store cylinders safely and securely to prevent them from
falling. Do not store them near elevators, stairs or gangways,
or in unventilated enclosures such as cupboards.
(b) Handle cylinders one at a time and use rope slings only for
lifting — not chains or magnetic lifts.
(c) Always close the valves of empty cylinders, and store them
separately from full ones.
(d) Keep all cylinders away from electrical apparatus, heat and
other sources of ignition.
(e) Store oxygen cylinders separately from fuel gas cylinders.
(f) Keep all oxygen cylinders and fittings in a place where they
cannot be contaminated by oil or grease. These substances can
ignite violently in the presence of oxygen, and if the oxygen is
under pressure an explosion may result.
(g) Always store and use acetylene cylinders in the upright
position. They contain liquid acetone to keep the acetylene
stable. If the valve is opened when the cylinder has been on its
side, liquid acetone will be will be withdrawn with the gas. If
the cylinder has been on its side, stand it upright for at least an
hour before use.

9
 ARCHIVE
Gases used in welding and cutting

OXYGEN (02) makes up about 20 percent of the air around us. It is not
a flammable gas, but usually nothing can burn unless oxygen is present.
If the amount of oxygen in the air is increased, even slightly, the
air itself becomes dangerous. Sparks will readily ignite into fires, fires
will burn much more fiercely, and flames will spread more quickly. If
clothes catch fire in an oxygen-enriched atmosphere they will burn as if
soaked in petrol.
Never allow the air to become enriched with oxygen through leaks
or misuse. For example, do not use oxygen to “sweeten the air” in a
confined space or to blow dust off clothes.
Do not use oxygen to power tools which run on compressed air as
any oil or grease in the tool may burst into flames or explode.
ACETYLENE (C2H2) burns quietly and smokily with a white flame.
Mixed with oxygen, it produces the blue, very hot flame used in welding
and cutting.
Acetylene cylinders are filled with a porous material containing
acetone into which the acetylene is dissolved. Acetylene is an unstable
gas and dangerously so at pressures over 100 kPa (14.5 lbs/in2). Never
set the cylinder outlet gauge at a higher pressure than this.
Acetylene forms an explosive mixture with oxygen at
concentrations from 2 percent up to 82 percent. This can easily happen
if there is a leak, especially in a confined space. Acetylene smells like
garlic or onions, which helps in detecting this hazard.
Copper, or any material containing 70 percent or more of copper,
forms an explosive compound (copper acetylide) with acetylene which
is likely to explode on impact. For this reason, never join acetylene
hoses with copper tube or copper wire — always use the proper fittings.
LIQUEFIED PETROLEUM GAS (lpg) is used in oxy-lpg cutting and in
air-lpg heating torches. It is heavier than air and will collect in low-lying
places.
Lpg in New Zealand is approximately 60 percent propane and 40
percent butane. Because it is heavier than air, do not use lpg in trenches,
holes, or anywhere it can spill down to a lower level. As with acetylene,
the cylinder must be kept upright. This is because propane is a liquid,
and is likely to seep through the valve.
Lpg forms an explosive mixture with oxygen at concentrations of
between 2 percent and 10 percent.

10
 ARCHIVE
Assembly of equipment

THE OUTLET valves on oxygen cylinders and other, inert, gases are
threaded right-hand. The valves on acetylene, lpg and all other fuel
gases are threaded left-hand.
This safeguard of using right-hand threads for oxygen and left-
hand threads for fuel gases applies also to the associated equipment.
However, this does not mean that all equipment with right-hand
threads may be used for any inert gas, or that equipment with left-hand
threads may be used for any fuel gas. Only equipment labelled for use
with the particular gas may be used.
The proper sequence for assembling equipment is as follows:
(a) Make sure that the cylinder valve threads are free from oil,
grease and other foreign matter.
(b) Open each cylinder valve briefly to blow out any dust or
moisture inside the thread.
(c) Fit the regulators to the cylinders.
(d) Make sure the regulator pressure adjusting screws are
released, by turning them anti-clockwise until they are slack.
(e) Open each cylinder valve slowly. When the high-pressure
gauge needle has stopped moving, screw in the pressure
adjusting screw until a steady flow of gas issues from the
regulator outlet. This purges the regulator of any dirt or dust.
Allow the gas to flow for a few seconds only then release the
pressure adjusting screw to stop the flow of gas.
(f) Fit the hoses to the regulators.
(g) Purge each hose to remove dust or dirt by the same procedure
used when purging the regulators.
(h) Fit the torch to the hoses.
(i) Fit the correct tip or cutting nozzle to the torch.
(j) Always check that all unions are correctly tightened and that
there are no leaks before lighting up. (Use a mixture of
detergent and water.) If you do this every time the equipment
is assembled, it will become automatic.
NOTE: The cylinder valve key should be left fitted to the
oxygen cylinder. This is to enable any person to turn the
cylinders off in case of an incident.

11
 ARCHIVE
Flashbacks: the causes and cure

FLASHBACKS are the unintentional and uncontrolled burning back of

gas through the blowpipe mixer. They result from the presence of
oxygen and a fuel gas in the same supply line. Any flashback will
damage the equipment to some extent. A serious flashback — or several
minor ones — will make the equipment unsafe for further use, unless it
is properly overhauled.
Many flashbacks go unrecognised. Sometimes the only sign is a
loud crack, followed by a puff of carbon from the welding tip when
relighting. This carbon, which is produced by the decomposition of the
fuel gas, is proof that a flashback has occurred.
The least damage a flashback can do is to deposit carbon in the
torch valves, which can affect their operation and lead to more serious
flashbacks. If, as is likely, the flame travels some distance along the
hoses, the bore will suffer damage and be weakened. Small particles
may break loose and lodge in the valve or mixer.
Serious flashbacks can cause substantial and expensive damage to
the regulator and may even pass right through it and into the cylinder,
causing a cylinder fire.
The most common causes of flashbacks are:
• Excessive or incorrect pressures set by the operator, resulting
in the gas flow rate exceeding the capacity of the cutting
nozzle or welding tip. The gas at the higher pressure then
flows into the lower pressure line. This can occur either if
incorrect pressures are used, or if incompatible items of
equipment are connected together.
• A leak from the regulator, hose, or connections results in a
drop of the gas pressure in the line, and gas from the higher
pressure line backfeeds into it.
• Leaking valves allow gas to seep through and mix by
diffusion when the equipment is not in use, such as during tea
breaks, meal breaks and overnight.
• Lighting up with both torch control valves open, but one
cylinder closed.
• When an oxygen cylinder becomes empty the fuel gas may
backfeed into the oxygen line, regulator and cylinder. If the
regulator is then placed on a new oxygen cylinder, and the

12
 ARCHIVE
Flashbacks cont’d

cylinder valve is opened too rapidly, the pressure can increase

the temperature of the mixed gas enough to ignite it.
The use of flashback arrestors can virtually eliminate this cause of
fires. A suitable fully integrated flashback arrestor is shown in fig. 4 on
page 7. Fitting an arrestor is recommended especially in situations
where the operator is not working close to the cylinder control valves.
Possible consequences of not arresting a flashback range from a burst
hose to the bomb effect of a cylinder exploding.
The functions of flashback arrestors are to:
• Protect against sudden or slow reverse flow of gas, by means
of a non-return valve.
• Arrest a flashback and extinguish the flame.
• Protect against leakage and ignition of unburnt gases after a
flashback by automatically shutting off the gas supply.
• Show when the arrestor has operated by means of an indicator.
• Vent off excess pressure in hoses via a safety valve.
• Shut off the gas supply if the arrestor inlet pressure falls
below the outlet pressure due to a leak in any of the supply
equipment.
For total protection, fit an arrestor to each gas line, one adjacent to
the regulator outlet and one at the handpiece. The arrestor will not have
to be fitted if the handpiece has a built-in arrestor. Consult the
manufacturer or supplier to make sure the correct model, for the
particular gas and for the particular equipment, is used.
NOTE: Should a flashback occur, first turn off the blowpipe
oxygen and then the acetylene. Inspect the hoses for possible
damage and replace if necessary. Purge the hose before
lighting up, but never in a confined space.

13
 ARCHIVE
Sequence for lighting up

MOST FLASHBACKS are preventable if the correct lighting up and

shut down procedures are carried out. This is the sequence to follow:
(a) Open both cylinder valves (using only the key supplied by the
manufacturer).
(b) Check that there is ample gas in both cylinders.
(c) Set the fuel gas regulator pressure in this sequence:
(i) Open the fuel gas valve on the blowpipe;
(ii) Adjust the pressure regulating screw until the gauge
reads correctly;
(iii) Close the blowpipe fuel gas valve.
(d) Set the oxygen regulator pressure, using the same sequence.
(e) Open the fuel gas valve on the blowpipe. Allow the gas to
flow for a few seconds to purge the hose of air or any mixture
of gases. Then close the valve.
NOTE: Never purge the hose in a confined space.
(f) Open the oxygen valve on the blowpipe and purge the oxygen
hose of air or any mixture of gases.
(g) Make sure that the torch is not pointed at any other person or
at the cylinders. Then light the fuel gas and adjust the valve
(until the flame stops smoking, if acetylene is being used).
Use a friction lighter or an electric lighter. Never use a
cigarette lighter or matches.
(h) Open the oxygen valve(s) on the blowpipe, gradually, and
adjust to the desired flame.
NOTE: Purging the hoses should become an automatic
procedure before lighting up after any shutdown such as a tea
break.

14
 ARCHIVE
Sequence for shutting down

ON COMPLETION of the welding work, these are the correct

procedures for shutting down:
(a) Close the fuel gas valve on the blowpipe.
(b) Close the oxygen valve(s) on the blowpipe.
(c) Close both cylinder valves.
(d) Open oxygen valve(s) to release the pressure in the hose and
regulator. When both gauge needles have fallen to zero, close
the oxygen valve(s).
(e) Wind back the regulator pressure adjusting screw to release
the pressure on the regulator diaphragm.
(f) Repeat steps (d) and (e) with the fuel gas valve and regulator.

15
 ARCHIVE
General safety rules

SOME ADDITIONAL safety hints are given below. If you are unsure
about any safety matter, always ask an experienced person.
(a) Many booklets and pamphlets suggest you should make
periodic checks for leaks by using soapy water. However there
are oils or fats in soap which are not compatible with high-
pressure oxygen. Instead, use a 5 percent solution of Teepol or
a similar detergent in water.
(b) Never fill an oxygen cylinder with compressed air from an oil-
lubricated compressor. This is because residual oil in the air
will be deposited in the cylinder. If the cylinder then goes
back into the pool, and is refilled with oxygen, an explosion
will occur. Any oxygen bottle, regulator or hose that has been
used with compressed air must be downgraded and not used
for oxygen again.
(c) Leave the key spanners in position on the cylinders when in
use so they can be closed quickly in an emergency.
(d) Keep hoses and other equipment from obstructing
passageways, ladders and stairways. Where hoses are required
to go over passageways, they should be protected from
scuffing.
(e) Never wrap hoses around cylinders or regulators, as a leak or
flashback could cause even more damage.

16
 ARCHIVE
Hazards and how to avoid them

HERE ARE the main hazards encountered in gas welding and cutting
and how you can avoid them.
Injuries from burns during and after welding
Wear protective clothing. Never point a torch towards any other
person. Chalk a warning onto hot metal so that others will not touch it or
stand on it.
Injuries from backfires of blowpipes and explosions in hoses and equipment
Only use equipment in good condition. Light up only as set out on
p.14 of this booklet. Fit flashback arrestors to equipment.
Explosion of gas-air mixtures in workshops
These generally result from leaking hoses or from connections not
being gas-tight. If there is a smell of gas in the workshop, do not light up
until the cause has been found and rectified and the area has been well
ventilated to clear away any residual gases.
Fires in the work area and vicinity
Good housekeeping is essential. There should be no flammable
liquids (including solvents or liquefiable solids) waste or flammable
materials in the area, or piles of rubbish in which sparks may smoulder.
Do not leave a lighted torch unattended, or hung over the gas bottles or
regulators.
Oxygen-enriched atmosphere
A small increase in oxygen content of the air will cause fierce
burning of flames and sparks. Avoid allowing the air to become oxygen-
enriched as described on p. 10.
Fumes and gases
These are not a problem in a well-ventilated workshop. But, in
confined spaces, carbon monoxide can be a hazard. It comes from the
incomplete combustion of acetylene, and from the welding or cutting of
metal covered with paints, varnish, resins, or carbonaceous materials
such as bitumen.
Carbon monoxide has no smell to warn of its build-up. Early
symptoms may be a headache or sleepiness. At carbon monoxide levels
near the threshold limit of 50 ppm (parts per million) the symptoms are
a lack of concentration and co-ordination, and then unconsciousness.
17
 ARCHIVE
Hazards cont’d

Fumes of all descriptions should be disposed of promptly, especially

those from zinc and lead oxides. These are given off when flame is
applied to metals primed with zinc and lead paints. No one should be
exposed to fumes from zinc, lead, brass, bronze, copper, nickel, arsenic,
cadmium, manganese, phosphorus, selenium, silicon, beryllium,
mercury, fluorine, or stainless steels.
Good workshop ventilation, coupled with mechanical extraction
devices or breathing apparatus, is necessary.
Eye injuries
Suitable eye protection must be provided by employers and worn
by workers. There are types available, with either tinted or clear lenses,
to suit all types of work.
If in doubt, ask for advice from the manufacturer and/or supplier.
Use only the correct type of eye protection for the job.

18
 ARCHIVE
Repair of petrol tanks etc.

SEVERE EXPLOSIONS and fires, many resulting in fatalities, have

been caused by welding, cutting, brazing, soldering, or other
applications of heat to pipes, tanks, drums, and similar vessels which
have contained flammable materials and have not been made safe for
this work.
Containers which have previously held petrol or white spirit and
other such volatile liquids are highly dangerous to work on. A pin-point
of heat can be enough to set off an explosion or fire.
Equally dangerous are pipes or containers which have carried or
held such diverse contents as linseed oil, soap, diesel oil, any acid that
reacts with metals to produce hydrogen, or any combustible solids
which may have left a residue of dust.
It is essential to remove all residues during cleaning. The preferred
method is to steam clean and then either to fill with an inert gas such as
carbon dioxide or nitrogen, or to fill with water, leaving a very small
vented space at the point where the repair is to be made. (Allow for the
expansion of liquid in small-bore pipes.)
Never wash the container out with cold or hot water, or blow the
container out with air, to remove flammable material. Both methods are
ineffective.
The use of carbon tetrachloride is not recommended because:
• It is highly toxic.
• It can form phosgene gas when heated.
• It may react with the metal of the containers.
• It has been found to be ineffective on a number of occasions
in cleaning containers and explosions have followed.
Cleaning with trichloroethylene must be carried out with care
since:
• It is toxic.
• It decomposes on heating and may form phosgene gas.
Welders are recommended to study the booklet Hot Work on
Drums and Tanks (obtainable at any Department of Labour office)
before carrying out such repairs.

19
 ARCHIVE
ELECTRIC WELDING PLANT AND EQUIPMENT

Fig. 6 A MIG (Metal Inert Gas) welding plant. The complexity of this
equipment makes it suitable for use only by experienced workers.

20
 ARCHIVE

Fig. 7 Well-insulated modern electrode holders of the screw type.

Fig. 8 Typical safety equipment for the protection of eyes, ears, and hands.
These are suitable for various tasks, but it is important to select the correct
equipment for the work undertaken.

21
PART II — ELECTRIC WELDING
ARCHIVE
Arc welding machines

BOTH AC and DC welding generators and AC/DC transformer rectifier

welding machines operate on relatively high voltages that can seriously
injure or kill.
Under normal operating conditions, it is not possible to get a shock
from the outer casing or the frame of an electric welder. Should anybody
receive one, stop the engine of an engine-driven generator or switch off
the power supply and remove the connection plug from the mains
supply. Do not restart the machine until it has been cleared by a
registered electrician.
Do not use any welding machine that has been tampered with by
an unauthorised person. Only a registered electrician may make
alterations or repairs to the electrical supply, or to the internal electrical
connections of any welding machine.
Before using any welding machine, check the location of the
power disconnect switch. In an emergency, there may not be a chance to
pull the plug out.
Follow all printed rules and operating instructions supplied by the
manufacturer.

22
 ARCHIVE
Equipment checklist for operators

MODERN ELECTRIC welding equipment is well designed and easy to

adjust, but should be checked over before use. This is the suggested
checklist for operators:
(a) If the machine has become wet, disconnect the primary power
and dry it before use.
(b) Spread out the coiled welding cable and check the insulation
for damage.
(c) Reject all welding lead spliced within 3 metres of the holder.
(d) If a metal inert gas (MIG) or tungsten inert gas (TIG) welding
process is used, check the gas hoses and fittings for leaks.
(e) Check electrode holders for loose or exposed connections to
reduce the shock hazard.
(f) Check that the welding machine frame is earthed, with special
attention to earth connections.
(g) Do not earth to pipelines carrying gas or flammable liquids, or
to conduits carrying electric wires.
(h) If it is unavoidable for AC welding to be performed under wet
conditions, a reliable automatic control should be fitted to
reduce the no-load voltage. This is to prevent shock. Refer to
a registered electrician or to the manufacturer for advice.

23
 ARCHIVE
General safety rules

SOME ADDITIONAL safety rules for operators are given below:

(a) Always treat all electrical equipment as “live”. Do not take
chances. Keep water and other liquids away and keep yourself
dry.
(b) Keep leads and cables clear from obstructing passageways,
ladders and stairways.
(c) Use only cables of a sufficient capacity to carry the current
used. Do not overload.
(d) Use only a proper earthing clamp or bolted terminal.
(e) Use only standard cable connectors.
(f) Use only an insulated hook or other suitable device to hold the
electrode holder when you are not actually using it.
(g) If you are using a welding generator driven by an internal
combustion engine inside a building or confined area, the
engine exhaust must be conducted to the outside air.
(h) Input cables and extension leads should be kept as short as
practicable.
(i) Take particular care in earthing portable welding machines
driven by an internal combustion engine. Where an earthing
connection is provided, it must be used in accordance with the
manufacturer’s instructions. (This is also very important when
using ancillary power supply for drills, grinders and other
equipment).

24
 ARCHIVE
Hazards and how to avoid them

ELECTRIC WELDING has its own set of hazards. Here are the main
ones and how to avoid them:
Electric shock
Check the insulation of all cables regularly. Do not work in wet
conditions unless suitable precautions have been taken. Electrical work
should be carried out only by a registered electrician.
Burns
Wear suitable protective clothing. Cool down or clearly mark hot
objects.
Eye hazards
Use only a suitable helmet or handshield which is in good
condition. Always wear approved safety spectacles with side shields,
goggles or a visor when chipping or grinding. Ensure that adequate
welding screens are erected where practicable.
Fumes, vapours, dust, and gases
Make sure the work area is well ventilated. There are health risks
from the toxic substances in fluxes, filler rods, coatings, and cleaning
agents, and the by-products of heat and ultraviolet radiation from the
arc.
Dangerous substances
Some dangerous substances to note are:
BERYLLIUM. Used mainly as an alloy with other metals, beryllium is
deadly and extreme precautions must be taken. This metal must be
welded in inert atmospheres, inside airtight enclosures, with the welder
outside.
CADMIUM. Used in electroplating and as an alloy with metals,
cadmium is also an ingredient in some paints. A single exposure to
cadmium oxide fumes can cause a severe lung irritation that may be
fatal.
CHROMIUM. The oxidation of chromium alloys can produce
chromium trioxide fumes, often referred to as chromic acid. These
fumes may produce skin irritation as well as bronchitis and other
problems.

25
 ARCHIVE
Hazards cont’d

LEAD. Poisoning generally results from inhalation of fumes, although

the swallowing of dust is also a cause. Lead-based paints are a source of
lead fumes, especially when old steel structures are cut or welded. Signs
and symptoms of lead poisoning may include abdominal pains,
constipation, headaches, weakness, muscular aches or cramps, loss of
appetite, nausea, vomiting, weight loss, and anaemia. In severe cases it
can be fatal.
MAGNESIUM. The oxide fumes from magnesium can produce metal
fume fever, which is characterised by influenza-like symptoms.
MANGANESE. Fumes from manganese are highly toxic and can
produce total disablement after a few months of exposure to high fume
concentrations.
MERCURY. Mercury vapour can be produced by welding or cutting
metals coated with protective materials containing mercury compounds,
such as the antifouling paints used on ship bottoms. Nowadays less toxic
substitutes are used in place of mercury, but there will still be some
vessels in service which are protected with mercury-containing
antifouling compounds. Exposure to mercury vapour may result in
abdominal pain, vomiting, diarrhoea, and other serious problems which,
collectively, can result in death.
NICKEL. Often used as an undercoating on chrome-plated parts, nickel
and its compounds are generally considered to have low toxicity.
TITANIUM. Dust may irritate the respiratory tract in high
concentrations.
VANADIUM. Dust and vanadium pentoxide fumes may cause severe
eye, throat, and respiratory tract irritation and pain.
ZINC. Welding, brazing, or flame cutting of galvanised steel causes zinc
oxide fumes. Inhalation of these may result in metal fume fever.
FLUORIDES. These and other toxic compounds of fluorine may be
found in some welding and brazing fluxes, electrode coverings and
submerged arc fluxes. Containers are labelled to warn of the presence of
fluorides. The fumes will cause chills, fever, painful breathing, and
coughs if inhaled. Over a long period, fluoride can build up in the bones,
causing them to lose calcium and become brittle.
NITROGEN DIOXIDE. Formed in the welding arc directly from the air,
nitrogen dioxide is very irritating to the eyes and mucous membranes of
the lungs and throat. Exposure to concentrations between 200 ppm and

26
 ARCHIVE
Hazards cont’d

700 ppm (parts per million) can be fatal. Lower concentrations may
produce only mild bronchial irritation, but will be followed several
hours later by acute pulmonary oedema (fluid in the lungs).
PHOSGENE. This gas is produced when residues of chlorinated
hydrocarbon degreasers such as trichloroethylene and perchloroethylene
are left on metal being welded or flame-cut. The heat and the ultraviolet
radiation cause the degreaser to decay into phosgene gas, which was
used as a poisonous gas in the First World War. Freon gas, which is used
in many refrigeration plants and as a propellant in aerosol cans, will also
decompose to form phosgene when exposed to ultraviolet rays.
Phosgene will produce skin inflammation. Inhalation of high
concentrations will cause pulmonary oedema. Death may result through
respiratory or heart failure.
PHOSPHINE. When steel which has been coated with a phosphate
rust-proofing is welded, phosphine gas is generated. High
concentrations will irritate the eyes, nose, and skin. Very high
concentrations can result in severe damage to kidneys and other organs
and perhaps death.
OZONE. A gas produced by the ultraviolet radiation in the air in
the vicinity of arc welding and cutting operations, ozone is very
irritating to all mucous membranes. Excessive exposure produces
pulmonary oedema. Other effects of exposure include headache, chest
pain, and dryness of the respiratory tract.

27
PART III — FURTHER SAFETY PRECAUTIONS
ARCHIVE
Training of gas/electric welders

THE CARDINAL rule is do not use welding equipment unless you are
adequately trained and familiar with its safe use.
The Factories and Commercial Premises Act 1981 contains
specific provisions about training of personnel using dangerous
equipment. Never operate equipment which you do not understand. If
you notice untrained personnel using dangerous equipment, or anyone
using dangerous methods, report the matter to your supervisor
immediately.
If your supervisor does not act to stop the offence, inform your
trade union representative or the Department of Labour.

28
 ARCHIVE
Overalls and protective clothing

SPATTER FROM the welding arc, ultraviolet radiation, and slag from
chipping can all cause burns or health problems. Always wear industrial
overalls and appropriate eye protection when you are engaged in
welding and cutting operations. Keep overalls fastened up to the neck,
with the sleeves down and fastened about the wrist.
Wear gloves or gauntlets for arc welding, as protection against
shock, burns and radiation burns. Various jobs may require additional
protective clothing to be worn such as aprons, leggings, skull caps, and
shoulder covers. Safety footwear, preferably boots, should also be worn,
especially when heavy materials are handled.
The employer has a duty to provide these items where needed, and
the worker must wear them. All such items must be made of suitable
flame-resistant materials.

29
 ARCHIVE
Protective equipment

NEVER USE a helmet or shield which has cracks, splits, or pinholes in

it. Similarly, do not use, even for the smallest job, a cracked or broken
filter glass. It is an offence for an employer to provide unsatisfactory
equipment, and no worker should knowingly use it.
Safety spectacles with side shields must always be worn for
chipping or grinding, or when in an eye danger area.
You have a specific duty to protect others from the ultraviolet
radiation given off by electric arc welding. Unless you are welding in a
room or a booth which prevents other people from being affected, you
must place suitable screens around the work.
There are several types of portable, flame-resistant screens and
translucent curtains available. If a screen is damaged it must not be used
again until properly repaired. It may sometimes be necessary to use
suitable signs in addition to the screens.
Noise is not usually a problem associated with gas welding and
cutting, but some operations involving fabrication of steel plate can
generate high noise levels. If so, or if there are noisy processes nearby,
discuss the matter of personal hearing protection with your supervisor.
If fumes given off from the work are highly toxic, such as those
from cadmium, chromium, or beryllium, then some form of respiratory
protection, such as an air-supplied helmet, is still necessary even though
the work is done outside.

30
 ARCHIVE
Fire protection and extinguishers

FIRES ARE an ever-present danger around welding and cutting work.

No welding or cutting work should be started unless all the requirements
in this checklist have been met:
(a) All operators who are to use the equipment must be fully
trained.
(b) All equipment must be in good working order and correctly
assembled.
(c) Cylinders must be secured against falling or being knocked
over.
(d) Sufficient and suitable fire extinguishing equipment must be
available in the immediate vicinity of the work.
(e) All workers should know how to operate the fire
extinguishing equipment.
(f) Fire watchers must be appointed in locations where any major
fire may develop.
It is recommended that “Hot-Work Permits” (as shown in the
examples overleaf) be issued by the supervisor but only when the
supervisor is satisfied that it is safe to proceed.
The chart on page 33 of this booklet should be helpful in dealing
with small fires. Always notify the Fire Service even if you put the fire
out. They may wish to examine the scene for your benefit.
Fires from gas welding operations tend to occur while work is in
progress, while those caused by arc welding often occur some time after
work has ceased. This is because hot slag and spatters of molten metal
will bounce into awkward places, where they are not noticed, and
smoulder for some time before igniting.
Be careful when wetting down the work area, especially where
there is electrical equipment. It is advisable to check the area an hour or
so later. A fire watcher, equipped with sufficient and suitable fire
fighting equipment, must remain behind until all danger of fire has
passed. This will be not less than 30 minutes after hot work has been
completed.

31
 ARCHIVE
HOT WORK PERMIT HOT WORK PERMITS
TO BE DISPLAYED ON THE Left: Example of a hot work
WELDING OR CUTTING permit which can be printed on a
APPARATUS AND card and attached to a welding
RETURNED TO THE trolley. (Published by the
RESPONSIBLE OFFICER Australian Fire Protection
ON COMPLETION OF Association Ltd.)
THE WORK. Below: Example of NZS 4781

Permission Granted to

I have inspected the work. The permit is withdrawn as from...........................

............................is hereby authorised to carry out: cutting, burning, welding
(cross out where not applicable)

Signed...............................................
Factory manager or nominee
Signed.........................................
To Use (Type of Equipment)

(Date:time)
Factory manager
In (Location)

other work on..................................as from...................................

On (Date) (Date: time)

From (Time)
HOT WORK PERMIT

To (Time)
1. All combustible
materials removed
or made safe
2. No flammable liquids,
vapours, gases or
(Plant or equipment)

dusts present
3. Extinguishers/hoses
provided on site
4. Operator knows how
to use fire equipment
5. Operator knows
location of telephone/
fire alarm
6. Site inspected after
completion of work
(Name)

Permit issued by
(Responsible Officer)

32
 CLASS OF FIRE APPROVED TYPE OF EXTINGUISHER

Water Foam Vapourising Dry Chemical CO2 Gas

Liquid
Bucket Pump 9l Mixed Chemical B.C.F. Ordinary Dry Powder Gas under ptressure
Water/Gas expelled. type Multi-purpose
Soda Acid. 9l Stored Pressure
type.
A
CLASS “A” FIRES
Ordinary Combustibles YES YES Small fires only Small surface fires Small surface fires
Paper, wood, cloth, etc. only only
COOLING ACTION
B
CLASS “B” FIRES NO YES YES YES YES
Burning Liquids
Petrol, oil, paint,
fats, etc.
SMOTHERING ACTION
C
CLASS “C” FIRES
Gases or liquefied Cautious use as YES YES YES YES
Gases spray to dilute
DILUTE or disperse gas only
gas
SMOTHER liquid
HOW TO USE Direct jet at Allow foam to Direct jet to Direct discharge to Direct discharge to
heart of fire and fall lightly on front edge of fire front edge of fire front edge of fire
saturate. Fine burning surface first, sweeping first, sweeping first, sweeping from
spray to dilute to form a smoth- from side to side from side to cover side to side to cover
or disperse gas. ering blanket. to cover burning burning area. burning area. Note:
area. Rising heat may drive
CO2 away.

ELECTRICAL FIRES

33
It is not now considered that electrical fires constitute a class, since any fire involving or started by electrical equipment must, in fact, be a fire of Class
A, B or C. The normal procedure is to cut off the electricity and use an extinguishing method appropriate to what is burning. It is, however, advisable
to use extinguishing agents which are non-conductors of electricity; these include: B.C.F., Dry Powder, Carbon Dioxide.
ARCHIVE
 ARCHIVE
Work in confined spaces

IT IS ALWAYS dangerous to work with welding or cutting equipment in

a confined space.
Here are the safety procedures to follow:
(a) Never enter any confined space unless you are satisfied it is
adequately ventilated with fresh air. If in doubt, wear suitable
respiratory protection.
(b) Do not attempt to weld or cut if the presence of explosive
vapours or dusts is suspected. Test the atmosphere with a
suitable gas detector.
(c) All workers should wear a safety belt or lifeline as
appropriate, so that they may be easily removed from the
confined space without the need for anyone else to enter it.
(d) Keep welding plant outside and run leads only to the work
site.
(e) Do not work in a confined space unless you are closely
watched by someone outside. This person must understand the
welding plant and must be able to shut it down properly and
quickly in an emergency.
(f) Remove the gas torch and hoses from the space every time
that work stops-even for tea breaks. A small leak, for ten
minutes or so, could result in an explosion when work re-
starts.
NOTE: A correct safety procedure should be adopted for work in
confined spaces. An “entry permit” system should be used,
and completed by an experienced person. A copy of the
completed entry permit should be posted at the work site. As
well as declaring the confined space safe to be worked in, it
should also ensure that all machinery (prime movers,
connecting pipes and electrical equipment) has been isolated
by blanking, disconnecting or valving. Valves should be
secured to prevent accidental operation.

34
 ARCHIVE
Ventilation systems

FUMES CAN be a serious problem in welding and cutting. They are

released from the coatings on welding rods and from the action of heat
or ultraviolet rays from the process reacting with solvents or coatings on
the metals being welded.
Some fumes are merely objectionable, but others are toxic and can
damage your health. Unless the work is being done in the open air,
mechanical ventilation is necessary to move the fumes away from the
worker and to produce a current of fresh air in the work area.
Always pay particular attention to ventilation when working in a
confined space, such as inside a boiler, tank or compartment of a ship.
Where gas-shielded arc welding is performed take care to guard against
creating an oxygen-deficient atmosphere. Air-supplied respirators, small
enough to fit beneath a welding helmet, are available and should be used
where satisfactory fresh air ventilation cannot be guaranteed.
There are two main types of mechanical ventilation:
General ventilation
Dilution of fumes by introducing or exhausting quantities of air
from the work room can be sufficient for many welding and cutting
activities if the workroom is large enough, if there are not too many
welders working within the area, and if there are no specially hazardous
chemical or physical agents produced by the welding or cutting.
Local exhaust ventilation
This is the most effective means of control and has the advantage
of providing a cleaner, healthier environment. It handles a smaller
volume of air and so results in a smaller heat loss from the workroom.
Care must be taken that:
• Exhaust openings are located as close as possible to the source
of the contamination.
• Contaminants are kept out of the breathing zone of the worker.
Exhaust hoods should be placed so as to draw fumes away
from the worker’s breathing zone.
• The exhausted air is discharged outside, and in a place where
it cannot contaminate fresh air being drawn into the work
room.

35
 ARCHIVE
Ventilation cont’d

Some types of ventilation systems are described below.

FREELY MOVABLE HOOD. This is a movable hood, attached to a fan,
which draws air from the workspace and exhausts it, via flexible
ducting, to the outside. It should provide an air velocity of at least 0.5m/
s across the welding site at even the most remote point from the exhaust
opening. The hood must always be placed as close as possible to the
work being done.
FIXED ENCLOSURE. This is a structure with a top and at least two
sides enclosing the welding or cutting operation. Ventilation is provided
so the area is continuously flushed with fresh air.
Air movement should be at least 0.5 m/s and the work should be
arranged and performed so that the fresh air enters the enclosure through
the worker’s breathing zone and then passes through the space in which
contaminants are produced.
DOWN-DRAFT BENCH. This is a bench or table which has an open
grid as the work surface. Air is drawn downward through the grid, into
exhaust ducting, and then expelled outside.
The contaminants should not be able to rise into the worker’s breathing
zone. Workpieces must not be so large as to cover too much of the
ducting or the exhaust effect will be lost.
EXTRACTOR NOZZLES. Semi-automatic welding processes, such as
the metal inert gas (MIG) processes, are now being supplied with built-
in slotted exhaust chambers. Contaminated air from around the welding
operation is drawn through the slotted exhaust chamber, which is
positioned to allow the welder a clear view of the electrode, and into the
exhaust system.
ELECTROSTATIC PRECIPITATORS. These are air cleaning systems
capable of very high efficiency. By recycling the already-warmed air in
the workplace they can make worthwhile savings in energy use,
especially during winter. Both fixed and portable models are available.
Many of these units have been designed particularly for welding
workshops. Contaminated air is drawn into the unit and passes through
an electrical field. The airborne particles receive a strong electric charge.
The air then passes into a second section containing electrically-charged
metal plates. These plates attract and capture the ionised particles and
the clean air is then returned to the room.

36
 ARCHIVE
VENTILATION SYSTEMS

Fig. 9 The Petone Technical Institute is an example of what can be

achieved when a workshop and its mechanical extraction system are
designed and built for welding and cutting.
The hood above the operator has a dual function. Around the outer rim are
slots which allow a down-draught of air to effectively seal off the work area
from the rest of the workshop, confining any fumes or particles within the
immediate area. At the same time, an up-draught sucks any fumes up
through the vents in the central part of the hood.
Each of the small work bays, which are curtained off from the main
workshiop, is fitted with a extraction ducts which are connected to a large
common duct.
37
 ARCHIVE

Fig. 1O An example of a fixed fume extraction unit in a welding bay at

Petone Technical Institute. There is a low-level vent, just above the work
table, to remove particles and heavy fumes. A high-level vent removes the
lighter fumes from near the ceiling. This type of unit works particularly well
when a blower or fan is used to push the air in the direction of the extractor
vents.

38
 ARCHIVE

Fig. 11 There are many designs of electrostatic precipitator available. They

are an efficient means of removing welding or cutting contaminants from
the air. In situations where the costs of heating or cooling the workshop are
significant, these units are highly suitable. The unit shown is mounted on a
trolley, making it fully portable.

39
 ARCHIVE
New Zealand Standards

NO PROTECTIVE clothing or equipment is suitable unless it provides

adequate protection from the particular hazards encountered. It is
therefore recommended that only products which comply with the
relevant New Zealand Standard be used, when there is a standard for the
item. Examples are eye protection, hearing protection, overalls, safety
footwear, and fire extinguishers.
All items which have been accepted as complying with the New Zealand
Standard, or with a suitable overseas Standard which has been accepted
for use in New Zealand, will bear a Standard Certification Mark.
Further information may be obtained from:

Standards Association of New Zealand,

Private Bag,
Wellington.
Phone 842 108.
Telex-NZ 3850.
Telegrams-Standards Wellington.

Any problems or questions may also be referred to the nearest

branch of the Health Department, Labour Department or NZ Fire
Service.
NEVER TAKE CHANCES WITH YOUR SAFETY OR WITH
ANYONE ELSE’S

40
APPENDIX 1
ARCHIVE
Special cutting and welding systems

THE FOLLOWING is a brief description of specialised cutting and

welding systems and their associated hazards.
TAGS (TIG) WELDING. A non-consumable tungsten electrode is
surrounded by a shield of inert gas. Weld metal is added by means of a
suitable uncoated filler rod without the use of a flux.
ATOMIC HYDROGEN WELDING. The arc is struck between two
tungsten electrodes, and a jet of hydrogen is directed into the arc.
CARBON ARC WELDING. The electrode used is a carbon rod. The
hazards for this and the above two processes are as for ordinary electric
arc welding and the usual precautions should be taken i.e., protective
clothing and equipment and ventilation.
UNDERWATER WELDING. Ordinary welding techniques and gases
are used. Apart from the diving hazards, the main problem is poor
visibility. Burns are the most common injury.
PROJECTION WELDING. Is a variation of spot welding. The machines
used are basically similar, except that the electrodes are replaced by flat
copper platens which exert a uniform pressure over the joint area.
Raised projections on the workpiece melt when the current is passed
through them and collapse, forming a spot weld.
FLASH WELDING. Is another way of using resistance heating to obtain
fusion. Two parts are clamped with a small gap between the faces and
are wired up to a large transformer.
A voltage of about 10V is used. As the parts are moved together,
the high points of the irregular surfaces come into contact and a high
current flows at these points, which melt through resistance heating.
Droplets of metal flow and other arcs form, which heat the whole
surfaces.
The two workpieces are gradually moved together and more high
spots touch, melt, and form molten droplets. This is called flashing, and
it removes contaminants as well as heating the two surfaces to a uniform
temperature. Eventually, enough force is applied to forge the two
surfaces together and any remaining molten metal is forced out to the
surface.

41
 ARCHIVE
Special systems cont’d

Currents in excess of 100,000A can flow across the interface and

power inputs of up to 200kVA may be used. Obviously, electrical safety
is particularly important, as is the use of suitable eye protection.
ARC-PLASMA WELDING. The temperature in a tungsten arc during
TAGS welding is about 11,000°C. By surrounding the arc with a water-
cooled copper tube, the area of the arc is restricted and the temperature
almost doubles, to about 20,000°C. The plasma gas is passed through
this and expands rapidly, issuing from the hole in the nozzle as a high-
temperature ionised gas jet.
MICRO-PLASMA WELDING. A low-current version of the above
method, used in welding metal less than 1 mm thick. Operates at only
about 0.1 to 10A.
ARC-PLASMA CUTTING. Is the most common use for arc-plasma.
Unlike oxy-acetylene cutting, a chemical reaction does not occur to
achieve melting, so it is useful for cutting non-ferrous metals, such as
stainless steel, aluminium, copper and nickel.
The hazards associated with plasma welding and cutting are
similar to those for ordinary electric welding and oxy-acetylene cutting,
and the same precautions in respect of electrical safety, protective
clothing and equipment, and work methods, should be taken. There are,
however, two additional hazards-noise and fumes.
The plasma jet is ejected through the torch nozzle at very high
velocities, generating high-frequency noise. All personnel in the vicinity
of plasma torches must be provided with suitable hearing protection.
The noise generated increases in relation to the thickness of the material
being worked, so the hearing protection should be suitable for use with
the thickest material that will be used.
The Departments of Health and Labour can arrange to measure
actual noise levels, and will advise on the control of noise to
surrounding areas and on suitable hearing protection for operators.
Plasma systems are used on metals such as stainless steel,
aluminium, copper and nickel, which give off various toxic fumes and
gases when they are vaporised. As the high temperatures and fast cutting
speeds result in a build-up of these fumes, it is essential that adequate
mechanical ventilation is provided, preferably by means of a down-draft
exhaust through a water quench tank, or a boxed-in cutting table. It is
stressed that no one at all should be allowed to breath these fumes.

42
 ARCHIVE
Special systems cont’d

THERMIC LANCING. Is a method of oxygen cutting, particularly

useful on large blocks of reinforced concrete, or underwater.
A steel tube is packed with steel rods and oxygen is passed down
the tube, where it reacts with the iron in the rods. To start the iron/
oxygen reaction, the end of the lance is heated to a dull red by an
ordinary cutting or welding torch. Intense heat is produced by the
chemical reaction, which is self-sustaining as long as oxygen is fed
down the tube. No fuel gas is used through the lance. The lance is
consumed in the process.
There are no additional hazards to those involved in ordinary oxy-
acetylene cutting.
LASER SYSTEMS. Laser is an abbreviation of ‘Light Amplification by
Simulated Emission of Radiation’, and refers to a high-energy beam of
light. For welding and cutting, the beam is generated in a Cot laser tube.
Material up to about 10 mm thick has been successfully welded. In
cutting, a jet of gas such as nitrogen or oxygen is often used in
conjunction with the beam to blow molten material out of the hole.
Although the beam is focused and guarded, there is always a
possibility of reflection from various objects, and suitable eye protection
should always be worn by anyone in the vicinity of a laser system.

43
APPENDIX 2
ARCHIVE
Welding terminology

MAGS: Metal arc gas-shielded.

Alternative names: MIG metal inert gas
MAG metal active gas
GMAW gas metal arc welding
CO2 welding
semi-automatic welding
MMA: Manual metal arc.
Alternative name: electric arc welding
TAGS: Tungsten arc gas-shielded.
Alternative names: TIG tungsten inert gas
GTAW gas tungsten arc welding
Argonarc welding
OXY-ACETYLENE WELDING: Alternative name: gas welding
PLASMA:A body of ionised gas produced when a welding arc generates
a temperature high enough to enable a gas to dissociate into positive
ions and electrons. The gas in the centre of the arc is dissociated into a
plasma. It then flows away from the centre of the arc and reassociates
itself to produce neutral atoms, giving up its energy in the form of heat.

44