PVQ PDF

Vickers
Piston Pumps
PVQ Piston Pumps

Variable Displacement, Quiet Series
For Industrial Applications
Revised 10/96
GB-C-2132
Introduction
PVQ piston pumps are in-line, variable

displacement units and are available in
nine sizes. Displacement is varied by
means of pressure and/or flow
compensator controls. An impressive
assortment of control options offers
maximum operating flexibility.
PVQs operate at quietness levels that
meet todays demanding industrial
conditions. The sound level of each unit
approaches or is below that of the
electric motor driving it. Sound is
reduced by a patented timing
arrangement that also produces low
pressure pulses in the outlet flow. This
Vickers, Incorporated 1997

All Rights Reserved
leads to reduced tendencies for noise in

systems using PVQs.
The PVQ series is capable of operating
with many types of hydraulic fluid.
Water-content and phosphate ester
fluids can be accommodated, in addition
to the typical petroleum based and
synthetic fluids.
Many PVQ pumps are available in a
thru-drive configuration to accommodate
a multitude of application and installation
requirements. Thru-drive models can be
coupled to various types and sizes of
fixed and variable displacement pumps,
resulting in a compact and versatile
package. Such a package offers lower

installed cost by reducing the installation
size and by requiring only one mounting
pad on the prime mover.
Quiet PVQs have excellent operating
characteristics, and the pumps many
control and mounting options allow
choosing the optimum model for any
application. Additionally, PVQs possess
the same durability and long life
characteristics expected of the best
industrial products in todays
marketplace. For over 75 years, the
Vickers name has been synonymous
with long trouble-free service.
Contents
Model Series
Maximum Geometric
Displacement
cm3/r (in3/r)
Rated Speed
r/min
Maximum Pressure
bar (psi)
Page
PVQ10
10,5 (0.643)
1800
210 (3000)
PVQ13
13,8 (0.843)
1800
140 (2000)
PVQ16
16,0 (0.976)
1800
210 (3000)
13
PVQ20
21,1 (1.290)
1800
210 (3000)
17
PVQ25
25,2 (1.540)
1800
210 (3000)
29
PVQ32
32,9 (2.010)
1800
140 (2000)
17
PVQ40
41,0 (2.500)
1800
210 (3000)
39
PVQ45
45,1 (2.750)
1800
186 (2700)
39
PVQ63
63,0 (3.844)
1800
210 (3000)
55
EDQ-L-30 Amplifier/Controller
61
Application Data
65
D Fluid Cleanliness
D Hydraulic Fluids and Temperature Ranges
D Fire Resistant Fluids
D Installation and Start-up
D Ordering Procedure
PVQ10 & PVQ13 Model Series
Ratings
Model
Series
Maximum Geometric
Displacement
cm3/r (in3/r)
Rated
Speed
r/min
Maximum
Pressure
bar (psi)
Input Power at Max.

Pressure & Rated Speed
kW (hp)
Approx.
Weight
kg (lb)
PVQ10
10,5 (0.643)
1800
210 (3000)
7,4 (10)
7,2 (16)
PVQ13
13,8 (0.843)
1800
140 (2000)
6,5 (8.75)
7,2 (16)
Pressure Limits
Case pressure 0,35 bar (5 psig) maximum
Inlet pressure 0,2 bar (5 in. Hg) vacuum to 2 bar (30 psig)
Model Code
1
1
P
V
Q
2
R
L
5
1
3
N
S
F
Pump design number
Inline piston pump

Variable volume
Quiet series
10 Design number subject to change.

Installation dimensions remain
unchanged for designs 1019.
Displacement in cc/rev and pressure

ratings
C**
Mounting flange specifications
CM**
Rotation viewed from shaft end

Right hand (cw), standard
Left hand (ccw), optional
C**V**B
Ports, type and location
Shafts, input
Straight keyed SAE A modified, .75
dia. x 1.75 long
Splined SAE A modified, 9T 16/32 DP
major dia. fit
Shaft end ISO 3019/2 E20N (available
with MA mount only)
Seals
Buna N, standard
Fluorocarbon, optional
10
11
C**VC**P
CG
Control type
SE SAE O-ring rear port, 1.0625 inlet

& outlet (standard)
SS SAE O-ring side port, 1.3125 linlet
& outlet (optional)
6
A2 Flange SAE J744 82-2 (SAE A)

MA Flange ISO 3019/2-80A2HW
(available with N drive shaft only)
4
Series PVQ
10 10,5 cc/rev (0.64 cir), 210 bar

(3000 psi)
13 13,8 cc/rev (0.84 cir), 140 bar
(2000 psi)
3
C**V**P
C**VC**B
Pressure compensator.
PVQ10: Standard model is
C21, indicating setting of 207
bar (3000 psi); range is 0221
in tens of bar (3503000 psi).
C14, indicating factory setting
of 138 bar (2000 psi); range is
0214 in tens of bar
(3502000 psi).
Low pressure compensator.
Standard model is CM7,
indicating factory setting of 69
Pressure compensator C**, as
above with load sensing.
Standard load sensing setting
is 11 bar (160 psi); range
1017 bar (150250 psi); with
bleed-down orifice. Example:
C21V11B indicates PVQ10
compensator with 207 bar
pressure setting and 11 bar
load-sense differential.
Pressure compensator with
load sensing as C**V**B
above, but with bleed-down
orifice plugged.
load sensing. Compensator
same as C** above. Standard
load sensing setting is 24 bar
(350 psi), range 1731 bar
(250450 psi). With
bleed-down orifice.
CD**
UV
10
12

load sensing. Same as
C**VC**B above, but with
bleed-down orifice plugged.
Pressure compensator
modified for hydraulic remote
control.
Electric dual range
compensator. PVQ10: CD21
is standard 210 bar setting of
high range (24210 bar).
PVQ13: CD14 is standard
140 bar setting of high range
(24140 bar). Both units
require low range to be set by
customer (20100 bar).
Unloading Valve for
accumulator circuits. See
installation details.
Control option
Blank Without adjustable maximum

displacement stop (standard)
D
Adjustable maximum displacement
stop (optional)
11
11
11
12
20
12
Control design
C** and CM**

C**D and CM**D
C**V(C)**B and C**V(C)**P
UV, CD** and CG
Special suffixes
S2 Shaft up mounting
S3 British Standard Parallel Threads
Counterbore Ports (ISO R288 threads).
Contact Vickers for available
configurations.
S9 Special CG compensator for use with
electronically modulated relief valves
Controls
adjusts pump flow in response to a

remote pressure signal and maintains
outlet pressure at a level slightly above
load pressure. The integral pressure
limiter overrides the load sensing
control, reducing pump displacement as
the preset maximum operating pressure
is reached.
Pressure Compensators
C & CM
The pressure compensator control
automatically adjusts pump delivery to
maintain volume requirements of the
system at a preselected operating
pressure. Maximum pump delivery is
maintained to approximately 3,4 bar (50
psi) below the pressure setting before
being reduced. The pressure
compensator control operates on one
side of center and has an adjustment
range as designated in the model coding.
Standard load-sense differential pressure

settings, by control type, follow. See
model code for setting range.
CG
requirements of the system at either of
two preselected operating pressures.
Maximum pump delivery is maintained
to approximately 3,4 bar (50 psi) below
either pressure control setting before
being reduced.
Control type and pressure range are
designated in the model code.
C**V11B Standard load-sensing and

pressure limiting control with 11 bar
differential pressure (standard factory
setting). Includes bleed-down orifice to
exhaust load-sense signal for
low-pressure standby condition.
C**V11P Same as C**V11B above,
but with bleed-down orifice plugged.
C**VC24B Same as C**V11B, but
with factory differential pressure setting
of 24 bar.
C**VC24P Same as C**V11P, but
of 24 bar.
C & CM
Pressure Compensator with

Adjustable Maximum
Displacement Stop D
The adjustable maximum stop pressure
control enables the maximum pump
delivery to be externally adjusted from
25% to 100% while maintaining all of the
standard features of a pressure
compensated pump. To assist initial
priming, manual adjustment control
setting must be at least 40% of
maximum flow position.
Remote Control Pressure

Compensator CG
Exactly the same as the C (pressure
compensation option) except the
machine operator is able to change the
compensator setting through the use of
a remote pilot relief valve, such as
Vickers C-175.
CD
Note: Graphic symbols shown with

external valve(s) and cylinder to
illustrate typical usage.
Electric Dual Range Pressure

Compensator CD
Load Sensing & Pressure

Limiting Compensators
The dual range pressure compensator

control automatically adjusts pump
delivery to maintain volume
C**V***B ({orifice open)

& C**V***P ({orifice plugged)
This compensator provides load sensing

control under all pressure conditions up
to the desired maximum. It automatically
3
PVQ10 Model Series

Note: To obtain full flow operation of pump, pressure compensator
setting must be 14 bar (200 psi) above desired operating pressure.
Full flow curves were obtained with compensator settings 14 bar
(200 psi) above 210 bar (3000 psi) max. rated pressure.
Volumetric efficiency
Performance Data
Oil type:
SAE 10W
Oil temperature: 49C (120F)
Inlet:
0.2 bar (5 in. Hg)
100%
80%
210 bar (3000 psi)

140 bar (2000 psi)
70 bar (1000 psi)
35 bar (500 psi)
60%
40%
100%
Overall efficiency
70 bar (1000 psi)
140 bar (2000 psi)
80%
60%
35 bar (500 psi)

210 bar (3000 psi)
40%
l/min
32
USgpm
8
16
140 bar (2000 psi)

70 bar (1000 psi)
35 bar (500 psi)
210 bar (3000 psi)
Input power
kW
15
hp
20
15
10
Delivery
10
210 bar (3000 psi)

140 bar (2000 psi)
70 bar (1000 psi)
35 bar (500 psi)
500
1000
Speed r/min
1500
2000
Input power
Delivery
24
PVQ13 Model Series

Performance Data
Oil type:
SAE 10W
Inlet:
0.2 bar (5 in. Hg)
100%
80%
140 bar (2000 psi)

70 bar (1000 psi)
35 bar (500 psi)
60%
40%
Overall efficiency
100%
80%
140 bar (2000 psi)

70 bar (1000 psi)
35 bar (500 psi)
60%
40%
USgpm
l/min
32
16
140 bar (2000 psi)

70 bar (1000 psi)
35 bar (500 psi)
Input power
kW
15
hp
20
15
10
10
5
Delivery
140 bar (2000 psi)

70 bar (1000 psi)
35 bar (500 psi)
500
1000
Speed r/min
1500
2000
Input power
Delivery
24
Sound Data
Sound Level dB(A)*
Full Stroke
Speed
r/min
Cutoff
PVQ13
51
53
43
42
55
54
48
50
100 (1500)
56
55
50
52
57
61
51
56
175 (2500)
59
51
35 (500)
53
54
46
44
70 (1000)
55
54
49
52
100 (1500)
56
58
51
56
140 (2000)
57
65
53
57
175 (2500)
60
54
35 (500)
56
56
47
44
70 (1000)
59
59
49
51
100 (1500)
59
60
51
55
140 (2000)
60
67
53
56
175 (2500)
62
53
35 (500)
58
58
52
49
70 (1000)
60
61
53
56
100 (1500)
62
63
55
58
140 (2000)
63
57
175 (2500)
1800
PVQ10
140 (2000)
1500
PVQ13
70 (1000)
1200
PVQ10
35 (500)
1000
Pre
re
Pressure
bar (psi)
65
57
*Sound pressure data equivalent to NFPA Standard.
Temperature: 50C (120F)

Test Fluid:
URSA-ED (10W)
Inlet Pressure: Atmospheric (0 psig)
Note: To ensure maximum noise

reduction at full flow conditions,
Engineering recommends limiting
pressure of PVQ10 to 175 bar (2500
psi) and PVQ13 to 100 bar (1500 psi) at
1800 rpm.
Response Data
Yoke response recorded at rated speed and pressure, 0 psi inlet, 82C (180F), SAE 10W oil. Pressure rise was 6900 bar
(100,000 psi) per second.
PVQ10
PVQ13
Control Type
On stroke
Off stroke
On stroke
Off stroke
0.040 sec.
0.020 sec.
0.048 sec.
0.016 sec.
Rear Ports, C & CM Controls, No.1 Shaft

Installation dimensions in mm (inches)
Compensator position
for R.H. rotation models
20,6
(0.81)R
162,8
(6.41)
Outlet connection for R.H.

rotation models 11/16-12
UN-2B straight thd. (0.75
O.D. tubing)
108,7
(4.28)
Compensator
position for
L.H. rotation
models
44,4
(1.75)
69,8
(2.75)
12,7
(0.50)
6,3(0.25)
6,1(0.24)
130
(5.12)D
Caution: While pump is operating do

not back compensator adjustment
screw out beyond dimension shown.
177
(6.97)
Case drain connection

.562-18 UN-2B straight
thd for .375 O.D.
tubing
28,4
(1.12)
84,8
(3.34)
84,8
(3.34)
Model number
shown here
79,2
(3.12)
50
(1.97)
82,55 (3.250)
82,50 (3.248) D
33,5 16,8
(1.32) (0.66)
Right hand
rotation
53,2
(2.09)
106,4
(4.188)
47,7
(1.88)R
11,1
(0.437)D
2 holes
4,79 (0.1885)
square
4,76 (0.1875)
52,3
(2.06)
28,6
(1.125)
163,6
(6.44)
25,4
(1.00)
Compensator
adjustment
screw 0.94 hex
19,05 (0.750)
D
19,02 (0.749)
Direction of rotation
shown here
38,1
(1.50)
21,13 (0.832)
21,00 (0.827)
28,4
(1.12)
57,1
(2.250)
67,8
(2.67)
Alternate
case drain
connection
135,9
(5.35)
Outlet connection for L.H. rotation

models 11/16-12 UN-2B straight
thd. (0.75 O.D. tubing)
Side Ports
Outlet connection 1.3125-12

UN-2B straight thd. (1.00 O.D.
tubing) for R.H. rotation models
153,2
(6.03)
79,2
(3.12)
50
(1.970)
Port
B
Port
A
38,1
(1.50)
177
(6.97)
Outlet connection 1.3125-12
UN-2B straight thd. (1.00 O.D.
tubing) for L.H. rotation models
165,1
(6.500)
52,3
(2.06)
82,5
(3.250)
No. 3 Shaft
N Shaft with MA Flange

(Flange and shaft end ISO 3019/2-80A2HW-E20N)
31,7
(1.25)
22,51
22,38
(0.886)
(0.881)
23,8
(0.938)
0.6249 Major
0.6245 Dia.
22,00
(0.866)
11,27
(0.444)
79,98
79,93
(3.149)
(3.147)
20,001
19,99
(0.788)
(0.787)
SAE standard involute spline flat root

major diameter fit. 9 teeth 16/32 pitch
diameter ref. .4835/.4725 minor diameter
36,0
(1.42)
5,99
5,97
(0.234)
(0.235)
Square key
8,51
(0.335)
7,24
(0.285)
54,50
(2.15)
109,00
(4.29)
Remote Compensator CG
Adjustment
1. Turn pressure control (such as C-175)
CCW to minimum setting.
Load Sensing with Pressure Limiting

Compensator C**V****
To mounting face
of pump mtg. flg.
2. Turn compensator adjustment plug to

desired minimum pressure (17 bar,
250 psi or higher).
3. Full pressure range can now be
obtained with pressure control.
Load sensing comp. control

port location for R.H.
rotation .4375-20 UNF-2B
boss connection
167,39
(6.59)
190,75
(7.51)
Caution:
Effective compensator pressure will be
CG compensator control setting (1769
bar, 2501000 psig) plus remote relief
valve setting.
Load sensing control port
location for L.H. rotation
45,1
(1.775)
28,45
(1.12)
Max.
19,05
(0.75)
28,45
D
(1.12)
.4375-20 UNF-2B
thread for CG
control models.
Connect to pressure
control, such as
C-175. SAE O-ring
boss connection
.250 O.D. tubing
Do not operate pump

with this port plugged.
Compensator adj. knob.

Do not back out adj. knob
beyond 28,4 (1.12) dim.
shown while pump is
operating.
Pressure Compensator
Control with
Adjustable Maximum
Displacement Stop D
Adjustment
Loosen locknut on adjusting rod. Turn
adjusting rod clockwise (CW) to
decrease maximum pump delivery, or
counter-clockwise (CCW) to increase
maximum pump delivery, until desired
setting is obtained. Secure this setting
by tightening locknut.
Adjustable maximum stop

pressure compensator control
position on left hand models
Minimum delivery position

(screw flush with nut)
Do not adjust below flush.
23,9 (0.94)
across flats
on hex.
232,9
(9.17)
194,6
(7.66)
94,5
(3.72)
15,7
(0.62)
50
(1.97)
22,7
(0.90)
94,5
(3.72)
28,4
(1.12)
87,9
(3.46)
Adjusting rod
(Approx. cc/rev
change per turn:
PVQ10 0.94
PVQ13 1.12)
Locknut 11,2 (0.44)

across flats
Vertical Shaft-up Installation S2 Drain Port Option
36,3
(1.43)
Additional drain port,
9/ -18 UNF-2B
16
Electric Dual Range

Control CD
Adjustment
1. With the directional valve
de-energized, loosen locknut 5 and
turn the adjusting screw 4 to the
desired first stage pressure setting,
then tighten locknut 5.
2. With solenoid de-energized, turn
adjusting spool 1 counterclockwise
(CCW) until nut 3 is bottomed in
adjusting screw slot. (Second stage
setting is now equal to first stage
pressure setting.) Turn adjusting
spool clockwise (CW) to desired
second stage pressure
requirements. One complete turn of
adjusting spool equals
approximately 41 bar (600 psi).
Energize solenoid and check
pressure setting. De-energize
solenoid and re-adjust if necessary.
Secure this setting by tightening
locknut 2.
1. Adjusting spool sets

288,5
(11.36)
2. Locknut 17,3 (0.68)

across flats
3. Locknut must be
contained within slot of
adjusting screw as shown
4. Adjusting screw 25,4
(1.00) across flats sets
first stage pressure
5. Locknut 31,7 (1.25)

across flats
158,7
(6.25)
158,7
(6.25)
50
(1.97)
Position for
R.H. models
Dual range pressure
compensator position
Solenoid Data (110V AC 50 Hz and 115/120V AC 60 Hz)

Solenoid current
115/120V AC 60 Hz
110V AC 50 Hz
Inrush amps
(R.M.S.)
2.0
Holding amps
.54
.64*
* Maximum peak inrush amps approximately 1.4 x R.M.S. value shown.
Refer to catalog GB-C-2015B for additional solenoid valve data.

Note: Any sliding spool valve, if held
shifted under pressure for long periods

of time, may stick and not spring return
due to fluid residue formation and,
therefore, should be cycled periodically
to prevent this from happening.
10
Electrical conduit
conn. 1/2 NPTF thd.
Electric Dual Range

Maximum Displacement
Stop CD**D
Maximum Flow Adjustment
With the system pressure below both
compensator settings, loosen maximum
stop adjusting screw locknut and adjust
screw to desired flow position (turning
screw clockwise decreases flow and
turning screw counterclockwise
increases flow). To lock screw in
position tighten locknut. To assist initial
priming, adjust control setting to at least
40% of maximum flow position.
Electrical conduit
connection 1/2
NPTF thd.
Minimum delivery
position (flush with nut).
Do not adjust below flush.
170,4
(6.71)
Position for
R.H. models
22,9
(0.90)
168,4
(6.63)
168,4
(6.63)
50
(1.97)
Locknut 11,2 (0.44) across flats
15,7
(0.62)
Maximum stop (adjusting screw)
Compensator Control
.250-20 UNC thd.

2. With directional valve de-energized,
turn adjusting spool 1
counterclockwise until nut 3 is
bottomed in adjusting screw slot.
(Second stage setting is now equal
to first stage pressure setting.) Turn
adjusting spool clockwise to desired
locknut 2.
Maximum delivery position

2. Locknut 17,3 (0.68)

across flats
212,8
(8.38)
91,4
(3.60)
3. Locknut must be
5. Locknut 31,7 (1.25)
across flats

Solenoid current
115/120V AC 60 Hz
110V AC 50 Hz
Inrush amps
(R.M.S.)
2.0
Holding amps
.54
.64*



11
Unloading Valve Control UV

With the unloading valve control the
variable pump will unload at a preset
pressure. The pump will maintain this no
flow, low pressure (approximately 14 bar
[200 psi]) standby condition, until
system pressure drops to about 85% of
the preset unloading pressure. The
pump will then return on stroke and
provide full flow until the preset
unloading pressure is reached again.
Unload valve
control port
To load
Inlet
With this control, an efficient

accumulator charging circuit is obtained.
The pump will provide full flow to fill the
accumulator until the maximum
charging pressure is reached. The
pump then goes to a standby condition
until the accumulator pressure drops to
85% of the desired maximum. The
accumulator is then recharged as the
cycle starts over again.
Check Valve
Outlet
Drain
Setting Pressures
A separate right angle check valve must
be provided to maintain the accumulator
hydraulic charge and prevent back flow
when the pump is unloaded. The check
valves internal leakage must not
exceed five drops per minute. The
control port must be connected to
system pressure, downstream of the
check valve.
1. Back out accumulator unloading

pressure adjustment screw to below
desired unloading pressure.
2. Adjust desired standby pressure.
Adjustment range
PVQ10 100210 bar (15003000 psi)
PVQ13 100140 bar (15002000 psi)
3. Set accumulator pressure by

screwing in the accumulator
unloading adjustment screw.
Accumulator recharge (cut-in)
pressure is a function of the
maximum accumulator pressure
and is not adjustable.
Cut-in pressure is 85% of unloading

pressure, minimum.
4. Check pressure settings and

re-adjust if necessary.
Standby pressure
adjustment
198,4
(7.82)
Control Port .4375-20

UNF-2B thd. SAE O-ring boss
connection .25 OD tubing
Accumulator unloading
pressure adjustment
225,3
(8.87)
145,5
(5.95)
164,3
(6.57)
70,6
(2.78)
29,5
52,3 (1.16)
(2.06)
79,2
(3.12)
50,0
(1.97)
Port
A
Port
B
56,1
(2.21)
12
PVQ16 Model Series

Ratings
Model Series
Maximum
Geometric
Displacement
cm3/r (in3/r)
Rated
Speed
r/min
Maximum
Pressure
bar (psi)
Input Power at
Max. Pressure &
Rated Speed
kW (hp)
Approx.
Weight
kg (lb)
PVQ16
16,0 (0.976)
1800
210 (3000)
11,2 (15)
15 (33)
Pressure Limits
Model Code
P
V
Q
2
R
L
5
10
11
Seals
10
Inline piston pump

Variable volume
Quiet series
Buna N, standard
Pump design number

D
stop (optional)

ratings

SE Inch SAE O-ring boss rear port

6
A2 Flange SAE J744 82-2 (SAE A)

4
Series PVQ
16 16,0 cc/rev (0.976 cir), 210 bar

(3000 psi)
3

9
Control type
11
Control option
Control design
10 CG and CV6
11 C**
C**
Pressure compensator. Standard

model is C21, indicating setting of
210 bar (3000 psi); range is 0221
CG Pressure compensator modified for
hydraulic remote control.
CV6 Load sensing. Standard load sensing
setting is 6 bar (90 psi) differential.
No pressure compensation and no
bleed-down orifice. Relief valve is
required, such as Vickers CS-06.
Shafts, input
Shaft SAE J744 16-1 (SAE A)
Straight keyed
13
Control C
pressure.
to approximately 5 bar (70 psi) below
the control pressure before being
reduced.
operates on one side of center and has
an adjustment range as designated in
the model coding.
P
Pressure Compensator Control

with Adjustable Maximum
Displacement Stop D
The adjustable maximum displacement
stop allows the maximum pump delivery
to be externally adjusted from 50% to
100%, while maintaining the standard
features of the pressure compensated
pump.

Compensator CG
This compensator is the same as the
C compensator, except the machine
operator is able to change the
a remote pilot relief valve. The pump
must not be operated with the remote
compensator port plugged; port must be
connected to a remote pilot relief valve,
such as Vickers C-175. The effective
compensator setting is the sum of the
compensator control setting and the
remote relief valve setting.
Load Sensing Compensator

Control CV6
This control provides load sensing
to the system relief valve setting. It
automatically adjusts pump flow in
response to a remote pressure signal
and maintains outlet pressure at
approximately 6 bar (90 psi) above load
pressure. By venting the load-sense line
with external valving (e.g., Vickers
DG4V-3 directional valve), when no flow
or pressure demands are placed on the
system, the pump will go to a no-flow,
low pressure, energy conserving
standby mode.
This control does not include maximum
pressure limitation, so a separate
system relief valve (e.g., Vickers CS-03)
is required. The system relief valve will
limit the maximum system pressure to
the selected level.
P
LS
Dr
Max. displacement adjustment

D (optional)
C
Note:
Graphic symbols shown with external
valve to illustrate typical usage.
Dr
CG
14
CV6
Dr
Performance at 1800 r/min

100%
Overall efficiency
12 (16.1)
60%
Delivery l/min (USgpm)
40%
Input power
10 (13.4)
8 (10.7)
Delivery
6 (8.0)
30 (8.0)
4 (5.3)
20 (5.3)
Input power Kw (hp)
Efficiency
80%
Input power pump compensated

2 (2.6)
10 (2.6)
0
70
(1000)
140
(2000)
210
(3000)
Outlet pressure bar (psi)
Sound Data
Speed
r/min
Sound Level dB(A)*
Pressure
Press re
bar (psi)
Full Stroke
Cutoff
35 (500)
52
37
70 (1000)
59
56
55
40
56
48
140 (2000)
57
54
210 (3000)
58
55
35 (500)
57
46
70 (1000)
58
51
140 (2000)
59
55
210 (3000)
60
58
35 (500)
62
48
70 (1000)
63
53
140 (2000)
63
59
210 (3000)
1800
55
70 (1000)
1500
47
57
35 (500)
1200
54
140 (2000)
210 (3000)
1000
65
62

Test Fluid:
URSA-ED (10W)
15
Response Data
Control Type
On stroke
Off stroke
0.062 sec.
0.030 sec.
Load sense compensator
0.057 sec.
0.028 sec.
C Control with Control Option D

Adj. screw
UNF
3/ -16
4
Case drain port Dr

3/ -16 UNF
4
Filling port
60
(2.36)
34
(1.34)
Square
4,785
4,760
(0.188)
(0.187)
87
(3.42)
For L models
Max. flow adj. rod
5 (0.20) hex hole
6,5
(0.25)
25,4
(1.00)
For R models
43
(1.69)
17,5 (0.69)
Max.
56
(2.20)
110,5
96
(4.35)
(3.78)
87
(3.42)
11,5
(0.45)
Effective
stroke
10,5
(0.41)
130
(5.12)
106
105
(4.17)
(4.13)
44,5
(1.75)
180
(7.08)
90
(3.54)
19,050
19,025
95
(0.750)
(3.74)
(0.749)
21,13 10,5
82,55
21,01 (0.41)
82,50 (0.830)
(3.250) (0.829)
(3.248)
CG and CV6 Controls

Non-adjustable
78
(3.07)
28,5
28,5
(1.12) Outlet port P
Inlet port I (1.12)
11/16-12 UN
11/16-12 UN
Shaft rotation and port
22,5
(0.88)
181
(7.12)
Rotation
R.H.
L.H.
Port I
Inlet
Outlet
Port P
Outlet
Inlet
117
(4.61)
Remote control port R for

CG control. Load sensing
port LS for CV6 control
7/ -20 UNF
16
96
(3.78)
56
(2.20)
78
(3.07)
Outlet port P
11/16-12 UN
28,5
(1.12)
43
(1.69)
28,5
(1.12)
Case drain port Dr
3/ -16 UNF
4
16
60
(2.36)
Filling port
Inlet port I
11/16-12 UN
Ratings
Model
Series
Maximum Geometric
Displacement
cm3/r (in3/r)
Rated
Speed
r/min
Maximum
Pressure
bar (psi)
Input Power at Max.

kW (hp)
Approx.
Weight
kg (lb)
PVQ20
21,1 (1.290)
1800
210 (3000)
14,9 (20)
14 (31)
PVQ32
32,9 (2.010)
1800
140 (2000)
15,6 (21)
14 (31)
Pressure Limits
Model Code
1
1
P
V
Q
2
Buna N, standard
10
11
Pump design number

ratings

10

Thru-drive without coupling
(available with side ports only)
C**V**B
Shafts, input
Straight keyed SAE B modified,

2.31 long
3 Splined SAE B modified, 13T
16/32 DP major dia. fit
N Shaft end ISO 3019/2 E25N (available
with MB mount only)
28 26-tooth splined shaft (Vickers). Used
in PVQ20/32 single to mount on
PVQ40/45 B26 thru-drive.
C**V**P
C**VC**B
C21, indicating setting of 207
C14, indicating factory setting
of 138 bar (2000 psi); range is
0214 in tens of bar
(3502000 psi).
Low pressure compensator.
Standard model is CM7,
indicating factory setting of 70
1017 bar (150250 psi); with
orifice plugged.
12
13

(250450 psi). With
bleed-down orifice.
control.
Electric dual range
high range (24210 bar).
PVQ32: CD14 is standard
140 bar setting of high range
(24140 bar). Both units
require low range to be set by
customer (20100 bar).
Unloading Valve for
C**VC**P
CG
CD**
UV
11
Control option
Control type
C**

& outlet (standard)
SS SAE O-ring side port, 1.625 linlet
& outlet (optional)
7
Seals
S
F
Blank No thru-drive
A9
SAE J744 82-2 (SAE A) w/9T spline
A11 SAE J744 82-2 (SAE A) w/11T spline
6
Inline piston pump

Variable volume
Quiet series
CM**
5
B2 Flange SAE J744 101-2 (SAE B)

MB Flange ISO 3019/2-100A2HW
R
L
Series PVQ
20 21,1 cc/rev (1.29 cir), 210 bar

(3000 psi)
32 32,9 cc/rev (2.01 cir), 140 bar
(2000 psi)
3

D
stop (optional)
12
11
11
12
20
13
Control design
C** and CM**

C**D and CM**D
UV, CD** and CG
Special suffixes
configurations.
17

is reached.
Pressure Compensator Controls

C & CM
maintained to approximately 75 psi
(PVQ20) or 100 psi (PVQ32) below the
pressure setting before being reduced.
operates on one side of center and has
an adjustment range as designated in
the model coding.

CG
to approximately 75 psi (PVQ20) or 100
psi (PVQ32) below either pressure
control setting before being reduced.

of 24 bar.
of 24 bar.
C & CM

Displacement Stop D

Compensator CG
Vickers C-175.
CD

Compensator Control CD
Load Sensing & Pressure Limiter

Compensator Control


18

PVQ20 Model Series

Performance Data
Oil type:
SAE 10W
Inlet:
0.2 bar (5 in. Hg)
100%
80%
35 bar (500 psi)

70 bar (1000 psi)
140 bar (2000 psi)
210 bar (3000 psi)
60%
Overall efficiency
100%
80%
70 bar (1000 psi)

140 bar (2000 psi)
210 bar (3000 psi)
35 bar (500 psi)
60%
40%
l/min
40
USgpm
10
24
16
6
35 bar (500 psi)
70 bar (1000 psi)
140 bar (2000 psi)
210 bar (3000 psi)
kW
15
Input power
Delivery
10
hp
20
15
210 bar (3000 psi)

140 bar (2000 psi)
70 bar (1000 psi)
35 bar (500 psi)
10
5
500
1000
Speed r/min
1500
2000
Input power
Delivery
32
19
PVQ32 Model Series

Performance Data
Oil type:
SAE 10W
Inlet:
0.2 bar (5 in. Hg)
100%
80%
35 bar (500 psi)

70 bar (1000 psi)
140 bar (2000 psi)
60%
40%
Overall efficiency
100%
80%
140 bar (2000 psi)

70 bar (1000 psi)
35 bar (500 psi)
60%
40%
l/min
76
USgpm
15
38
19
10
140 bar (2000 psi)

70 bar (1000 psi)
35 bar (500 psi)
Input power
kW
15
15
10
20
hp
20
10
140 bar (2000 psi)

70 bar (1000 psi)
35 bar (500 psi)
500
1000
Speed r/min
1500
2000
Input power
Delivery
57
Delivery
20
Sound Data
Sound Level dB(A)*
Full Stroke
Speed
r/min
Cutoff
Pre
re
Pressure
bar (psi)
PVQ20
PVQ32
PVQ20
PVQ32
35 (500)
53
58
43
47
70 (1000)
56
59
47
50
140 (2000)
57
61
52
54
210 (3000)
59
54
35 (500)
55
61
43
47
70 (1000)
58
62
48
51
140 (2000)
59
63
52
54
210 (3000)
61
55
35 (500)
57
63
47
50
70 (1000)
59
65
51
54
140 (2000)
61
65
56
55
210 (3000)
62
59
35 (500)
60
66
50
53
70 (1000)
62
67
53
56
140 (2000)
63
68
58
62
210 (3000)
64
58
1000
1200
1500
1800

Test Fluid:
URSA-ED (10W)
21
Response Data
PVQ20
PVQ32
Control Type
On stroke
Off stroke
On stroke
Off stroke
0.070 sec.
0.023 sec.
0.080 sec.
0.020 sec.
0.090 sec.
0.015 sec.
0.100 sec.
0.018 sec.
Thru-drive Shaft Torque Limits

Any deviation from these maximum torque values must be approved by Vickers engineering.
135 (1200)
208 (1850)
PVQ20/32A9
Input Shaft Code

1
Model Series*
Maximum Input
Torque Total
Nm (lb. in.)
337 (2987)
208 (1850)
PVQ20/32A11
337 (2987)
* SAE B 4 inch thru-drive pilot not available in PVQ20/32 frame size.
Vertical Shaft-up Installation S2 Drain Port Option
Additional drain port,

3/ -16 UNF-2B
4
22
58 (517)
(
)
135 (1200)
Maximum Thru-drive
Torque Output
Nm (lb. in.)
29,2
(1.15)
123 (
(1100)
)
Rear Ports, C & CM Controls, No. 1 Shaft
Case drain
connection
.7500-16
UNF-2B
straight thd.
(for 0.50
O.D. tubing)
208
(8.19)
58,7
(2.31)
146
(5.750)
73
(2.88)
9,5
(.375)
6,4 (0.251)
Sq. key
6,3 (0.250)
Compensator
position for R.H.
rotation models
189
123,7 (7.44)
(4.87)
74,7
(2.94)
84,8
(3.34)
33,3
(1.31)
Compensator
position for L.H.
rotation models
28,4
(1.12)D
B 28,4
(1.12)
82,5
(3.25)
101,6 (4.000)
101,5 (3.998)
45,7
(1.80)
66,5
(2.62)
B
65
(2.56)
52,3
(2.06)
22,9
(0.90)
14,3 (0.562)D
2 holes (for mounting)
25,1 (0.989)
24,9 (0.979)
120,6
(4.75)D
12,7
(0.50)
22,22 (0.875)
D
22,20 (0.874)
Right hand rotation
193,8
(7.63)
93,5
(3.68) 186,9
(7.36)
Outlet connection for

L.H. rotation models
1.6250-12 UN-2B thd.
(for 1.25 O.D. tubing)

R.H. rotation models
1.6250-12 UN-2B thd.
Alternate case drain connection

.7500-16 UNF-2B straight thd.
B Caution while pump is operating

do not back compensator adjustment
screw out beyond dimension shown.
Side Ports
Case drain connection

B 28,4
(1.12)
174,5
(6.87)
61
(2.40)
108,7
(4.28)
52,4
(2.062)
82,5
(3.25)
31,7
(1.25)
65
(2.56)
L.H. rotation models
1.6250-12 UN-2B thd. inlet or

outlet connection 2 places
196,8
(7.75)
98,5
(3.88)

R.H. rotation models
Alternate case drain connection

No. 3 Shaft
N Shaft with MB Flange

(Flange and shaft end ISO 3019/21000A2HW-E25N)
8,00
7,96
(0.315)
(0.314)
Square key
31,7
(1.25)
22,2
22,1
(0.873)
(0.872)
Major
Dia.
23,8
(0.938)
28,01
27,71
(1.103)
(1.091)
14,25
(0.56)
100
99,95
D
(3.937)
(3.935)
25,006
24,994
D
(0.9845)
(0.9840)
SAE standard involute spline flat root major

diameter fit. 13 teeth 16/32 pitch 0.8125 pitch
diameter (ref.) 0.7335/0.7225 minor diameter
42,0
(1.65)
10,5
(0.413)
9,25
(0.364)
70,00
(2.76)
140,00
(5.51)
23
Adjustment
1. Turn pressure control (such as
C-175) CCW to minimum setting.
2. Turn compensator adjustment plug
to desired minimum pressure
(17 bar, 250 psi or higher).
Load Sensing with Pressure Limiter C**V****

To mounting face
of pump mtg. flg.

boss connection
167,39
(6.59)
190,75
(7.51)

Caution:
valve setting.

28,45
(1.12)
Max.
45,1
(1.775)
19,05
(0.75)
28,45
D
(1.12)
.4375-20 UNF-2B
thread for CG
control models.
Connect to pressure
control, such as
C-175. SAE O-ring
boss connection
.250 O.D. tubing

beyond 28,4 (1.12) dim.
shown while pump is
operating.
Do not operate pump

Control with Adjustable
Max. Displacement Stop D
Adjustment
decrease maximum pump delivery or
counterclockwise (CCW) to increase
maximum pump delivery until desired

(screw flush with nut) do
not adjust below flush.
226,1
(8.90)
70,9
(2.79)
265,7
(10.46)
118,7
(4.66)
23,9
(0.94)
28,4
D
(1.12)
17,3
(0.68)
52,3
(2.06)
90,2
(3.55)
25,1
(0.99)
Locknut 11,2 (0.44)

across flats
24
Adjusting rod
(Approx. cc/rev
change per turn:
PVQ20 1.88
PVQ32 2.82)
Adjustable maximum stop

pressure compensator control
position on left hand models
28,4
(1.12)
Electric Dual Range

Control CD
Adjustment
locknut 2.
318,2
(12.53)

2. Locknut 17,3 (0.68)

across flats
3. Locknut must be
5. Locknut 31,7 (1.25)

across flats
134,9
(5.31)
158,7
(6.25)
52,3
(2.06)
Dual range pressure

Position for
L.H. models
Electrical conduit
conn. 1/2 NPTF thd.

Solenoid current
115/120V AC 60 Hz
110V AC 50 Hz
Inrush amps
(R.M.S.)
2.0
Holding amps
.54
.64*


25
Electric Dual Range

Stop CD**D
position, tighten locknut. To assist initial
Compensator Control
locknut 2.
201,7
(7.94)
Position for
L.H. models
25,1
(0.99)
23,9
(0.94)
52,3
(2.06)
Minimum delivery
position (flush with
nut). Do not adjust
below flush.

.250-20 UNC thd.

215,1
(8.47)
2. Locknut 17,3 (0.68)

across flats
93,5
(3.68)
3. Locknut must be

5. Locknut 31,7 (1.25)
across flats
144,5
(5.69)

Solenoid current
115/120V AC 60 Hz
110V AC 50 Hz
Inrush amps
(R.M.S.)
2.0
Holding amps
.54
.64*


26
Electrical conduit
connection 1/2 NPTF thd.

192,3
(7.57)

check valve.
Unload valve
control port
To load
Inlet
Check Valve
Outlet
Drain
Setting Pressures
Adjustment range
PVQ20 100210 bar (15003000 psi)
PVQ32 100140 bar (15002000 psi)


pressure, minimum.

Standby pressure
adjustment
pressure adjustment
246,4
(9.70)
174,5
(6.87)
174,5
(6.87)
145,5
(5.95)
82,5
(3.25)
52,4
(2.06)
65,0
(2.56)
56,1
(2.21)
27
A9 & A11 SAE A Thru-Drives

No. 1 shaft. Input torque not to exceed 73 Nm (650 lb. in.)
plus tabulated auxiliary pump torque with no overhung load.
Applications requiring overhung load capability or other
shaft ends are subject to approval by Vickers Engineering.
Note: Ports are reversed for

L.H. rotation.
Control location same for
both L.H. and R.H. rotation.
101,6 (4.00)
101,5 (3.998)
6,4 (0.251)
6,3 (0.250)
22,22 (0.875)
22,20 (0.874)
187
(7.36)
174,7
(6.88)
93,5
(3.68)
11,2
(0.44)
4,8
(0.188)
18,7 (0.738)
14,3
18,5 (0.729)
(0.562)
9,6
2 places 25,1 (0.989)
(0.39)
24,9 (0.979)
146,05
(5.75)
110,2
96 (4.34)
(3.78)
76,7
(3.02)
74,7
(2.94)
Output spline
(see table)
Thru-Drive
Cutaway View
Caution: While pump is operating,

do not back compensator adj. out
20,6
beyond 28,4 (1.12) dim. shown.
(0.81)
Construction plug. Do not remove.
Drain port .7500-16 UNF-2B thd. SAE
129,3
O-ring boss conn. .500 O.D. tubing.
(5.09)
28,4
Drain port .7500-16
7,9
(1.12)
UNF-2B thd. SAE O-ring (0.31)
boss conn. .500 O.D. tubing
.375-16 UNC-2B thd.
18,3 (0.72) deep
82,5
(3.25)
31,7
(1.25)
73,1
(2.88)
166,1
(6.54)
123,4
(4.86)
47,5
(1.87)
120,6
(4.75)
20,6
(0.81)
12,7
(0.50)
162
(6.38)
106,4
(4.19)
98,5
(3.88)
230,6
(9.08)
196,8
(7.75)
Inlet port R.H. see

note. 1.6250-12
UN-SAE str. thd.
SAE O-ring boss
connection 1.250
O.D. tubing
82,6
(3.252)
Use O-ring AS568-042 at interface
of auxiliary pump mounting
Outlet port R.H.

see note.
1.6250-12 UN-2B
thd. SAE O-ring
boss connection
1.250 O.D. tubing
Alternate drain port

.7500-16 UNF-2B
thd. SAE O-ring
boss connection
.500 O.D. tubing
A
See table
B
Model Series
ANS B92.1-1970
11 teeth 16/32 DP
Flat root side fit
Coupling Kit
16,7 (0.66)
33,0 (1.30)
02-136810
123 (1100)
ASA B5.15-1960
9 teeth 16/32 DP
Flat root side fit
A11
Installation Dimensions mm (in)
58 (517)
Spline Data
A9
Max. Torq e
Max Torque
Nm (in. lb.)
18,5 (0.73)
39,1 (1.54)
02-306041
Note: O-ring included with pump. Coupling kit, cap screws, and washers must be ordered separately to mount rear pump.
Typical Rear Pumps (with shaft codes) for PVQ20/32 Thru-Drives

Model
Series
Rear Pump
Shaft Code
PVQ10/13
PVB5/6
S124 suffix
V10
11
V20
A9
Typical Rear Pump
62
Note: A11 (not listed above) is intended for special application only.
28
Thru-drive
Coupling Kit
02-136810
02 136810
PVQ25 Model Series
Ratings
Model
Series
Maximum Geometric
Displacement
cm3/r (in3/r)
Rated
Speed
r/min
Maximum
Pressure
bar (psi)
Input Power at Max.

kW (hp)
Approx.
Weight
kg (lb)
PVQ25
25,2 (1.54)
1800
210 (3000)
16 (24)
14 (31)
Pressure Limits
Model Code
1
1
P
V
Q
2
R
L
5
1
3
N

Pump design number

ratings
CM**
C**V**B

Shafts, input
C**V**P
Straight keyed SAE B modified,

2.31 long
Splined SAE B modified, 13T
16/32 DP major dia. fit
with MB mount only)
C**VC**B
Seals
Buna N, standard
10
11
C**VC**P
CG
Control type
C**

& outlet (standard)
6
Inline piston pump

Variable volume
Quiet series

4
Series PVQ
25 25,2 cc/rev (1.54 cir), 210 bar

(3000 psi)
3
Standard setting 21 in tens of
bar (max. setting 201 bar).
Range 0221 in tens of bar.
Standard setting, 10 in tens of
bar (max. setting 103 bar).
Range 0210 in tens of bar
(3501500 psi).
1017 bar (150250 psi); with
orifice plugged.
(250450 psi). With
bleed-down orifice.
CD**
UV
10
12

control.
Electric dual range
high range (24210 bar). Unit
requires low range to be set
by customer (20100 bar).
Unloading Valve for
Control option

D
stop (optional)
11
10
11
12
20
12
Control design
C** and CM**

C**D and CM**D
CD**, CG, and UV
Special suffixes
configurations.
29

is reached.

C & CM
maintained to approximately 75 psi
(PVQ25) below the pressure setting
before being reduced. The pressure
compensator control operates on one side
of center and has an adjustment range as
designated in the model coding.

CG
to approximately 75 psi (PVQ25) below
being reduced.

of 24 bar.
of 24 bar.
C & CM

Displacement Stop D

Compensator CG
compensation option), except the
Vickers C-175.
CD


Compensator Control


30


Oil type: SAE 10W
Oil temp: 50_ C (120_ F)
Inlet pressure: 0 psi
100%
Efficiency
90%
kW (hp)
16,8 (22.5)
Overall efficiency
80%
70%
14,9 (20.0)
60%
13,0 (17.5)
Input power
9,3 (12.5)
Delivery
l/min (USgpm)
47,3 (12.5)
Delivery
7,5 (10.0)
Input power
11,2 (15.0)
50%
5,6 (7.5)
37,9 (10.0)
3,7 (5.0)
28,4 (7.5)
1,9 (2.5)
0
35
(500)
70
(1000)
100
(1500)
140
(2000)
175
(2500)
0
210
(3000)
31
Sound Data
Speed
r/min
Sound Level dB(A)*

Full Stroke
Cutoff
35 (500)
56.5
54.9
70 (1000)
57.7
58.3
100 (1500)
58.6
60.0
140 (2000)
59.5
61.3
175 (2500)
60.9
62.0
210 (3000)
66.6
63.1
35 (500)
60.9
56.9
70 (1000)
1000
Press re
Pressure
bar (psi)
62.4
60.1
100 (1500)
63.6
63.8
64.5
63.8
65.5
35 (500)
61.9
57.7
70 (1000)
63.5
61.9
100 (1500)
64.2
62.7
140 (2000)
65.3
63.3
175 (2500)
65.1
64.7
210 (3000)
65.9
65.3
35 (500)
64.0
59.0
70 (1000)
65.2
62.0
100 (1500)
66.0
63.4
140 (2000)
67.1
64.4
175 (2500)
67.5
65.7
210 (3000)
1800
62.3
63.3
210 (3000)
1500
63.1
140 (2000)
175 (2500)
1200
67.4
66.6

Test Fluid:
URSA-ED (10W)
Response Data
Yoke response recorded at rated speed and pressure, 0 psi inlet, 82C (180F),
SAE 10W oil. Pressure rise was 6900 bar (100,000 psi) per second.
Control Type
On stroke
Off stroke
0.030 sec.
0.012 sec.
0.040 sec.
0.012 sec.
32
Adjustment
1. Turn pressure control (such as C-175)
CCW to minimum setting.
2. Turn compensator adjustment plug to
desired minimum pressure (17 bar,
250 psi or higher).
Load Sensing with Pressure Limiter C**V****

To mounting face
of pump mtg. flg.

boss connection
167,39
(6.59)
190,75
(7.51)

Caution:
valve setting.

28,45
(1.12)
Max.
45,1
(1.775)
19,05
(0.75)
28,45
D
(1.12)
.4375-20 UNF-2B
thread for CG
control models.
Connect to pressure
control, such as
C-175. SAE O-ring
boss connection
.250 O.D. tubing

beyond 28,4 (1.12) dim.
shown while pump is
operating.
Do not operate pump

Control with Adjustable
Max. Displacement Stop D
Adjustment
counterclockwise (CCW) to increase
52,0
72,6 (2.05)
(2.86)
28,4
(1.12)
90,1
(3.55)
Locknut
11,2 (0.44) across flats
63,8
(2.51)
123,8
(4.87)
30,0
(1.18)
28,4
(1.12)
11,0
Max.
(0.43)
Adjusting screw
23,8 (0.90) across flats
Control position for

right hand rotation
Maximum stop
adjusting rod
(Approx. 2.22 cc/rev
change per turn)
Control position for

left hand rotation
220,2
196,2 (8.67)
(7.72)
252,1
(9.93)
Dimensions
to flange face
33
Electric Dual Range

Control CD
Dimension from
flange face
Adjustment
locknut 2.
312,1
(12.29)

2. Locknut 17,3 (0.68)

across flats
3. Locknut must be
5. Locknut 31,7 (1.25)

across flats
126,6
(4.98)
186,6
(7.35)
52,0
(2.05)
Dual range pressure

Position for
R.H. models
Electrical conduit
conn. 1/2 NPTF thd.

Solenoid current
115/120V AC 60 Hz
110V AC 50 Hz
Inrush amps
(R.M.S.)
2.0
Holding amps
.54
.64*


34
Electric Dual Range

Stop CD**D
Dimension from
flange face

position, tighten locknut. To assist initial
Compensator Control
locknut 2.
196,2
(7.72)
Position for
L.H. models
25,1
(0.99)
30,0
(1.18)
52,3
(2.06)
Minimum delivery
position (flush with
nut). Do not adjust
below flush.
Electrical conduit
connection 1/2 NPTF thd.
Maximum stop
adjusting rod
(Approx. 2.22 cc/rev
change per turn)
.250-20 UNC thd.

213,4
(8.40)

2. Locknut 17,3 (0.68)

across flats
93,5
(3.68)
3. Locknut must be
5. Locknut 31,7 (1.25)
across flats
136,3
(5.37)
196,3
(7.73)

Solenoid current
115/120V AC 60 Hz
110V AC 50 Hz
Inrush amps
(R.M.S.)
2.0
Holding amps
.54
.64*



35

check valve.
Unload valve
control port
To load
Inlet
Check Valve
Outlet
Drain
Setting Pressures
Adjustment range
PVQ25 100210 bar (15003000 psi)


pressure, minimum.

196,6
(7.74)
pressure adjustment
167,5
(6.59)

Standby pressure
adjustment
52,0
(2.05)
41,1
(1.62)
145,5
(5.95)
162,5
(6.40)
272,8
(10.74)
36
PVQ25 with C-type Control, No. 3 Shaft

Note: Ports are reversed
for L.H. rotation.
R.H. rotation
25,0
(0.98)
14,53
14,15
(0.572)
(0.557)
14,0 R
2 places
(0.55 R)
0,8
max. R
(0.03)
73,0
(2.87)
70,0
(2.76)
140,0
(5.51)
146,0
(5.75)
51,5
(2.03)
120,6
(4.75)
30,0
(1.18)
19,5 R
(0.77 R)
9.4
(0.37)
14,0
(0.55)
Outlet port B (see note) 1.0625-12 UN-2B thd.

SAE O-ring boss connection .750 O.D. tubing
(Shown for R.H. rotation)
196,6
(7.74)
167,5
(6.59)
44,0
(1.73)
60,0
(2.36)
101,60 30_
101.55
(4.000)
(3.998)
83,1
(3.27)
44,0
(1.73)
Drain port D2
.750-16 UNF-2B thd.
SAE O-ring boss
connection .500
O.D. tubing
56,0
2 places
(2.20)
47,0
(1.85)
28,4
(1.12)
52,0
70,0
(2.05) (2.76)
79,2
(3.12)
1.5
x 45_
(0.06)
162,5
(6.40)
#2 shaft
114,1
(4.49)
186,1
(7.33)
19,0
(0.75)
33,3
(1.31)
77,0
(3.03)
154,0
(6.06)
Compensator position for R.H. rotation

(Reverse for L.H. rotation)
41,1
(1.62)
Inlet port A (see note) 1.625-12 UN-2B thd.

SAE O-ring boss connection 1.250 O.D. tubing
(Shown for R.H. rotation)
29,5
(1.16)
Construction plugs
Do not remove
85,1
(3.35)
27,0
(1.06)
170,2
(6.70)
Alternate drain port D1

.750-16 UNF-2B thd.
SAE O-ring connection
.500 O.D. tubing
153,5
(6.04)
No. 1 Shaft

(Flange and shaft end ISO 3019/21000A2HW-E25N)
22,225
22,200
(0.8750)
(0.8740)
6,375
6,350
31,75
x
lg. key
(0.251) (1.250)
(0.250)
58,6
(2.31)
25,12
24,87
(0.989)
(0.979)
8,00
7,96
(0.315)
(0.314)
Square key
28,01
27,71
(1.103)
(1.091)
100
99,95
D
(3.937)
(3.935)
25,006
24,994
D
(0.9845)
(0.9840)
14,25
(0.56)
42,0
(1.65)
#1 shaft
1.5
x 45_
(0.06)
50.8
(2.00)
10,5
(0.413)
9,25
(0.364)
70,00
(2.76)
140,00
(5.51)
37
PVQ25 C**V(C)**P/B Load Sensing

with Pressure Limiter
196,6
(7.74)
167,5
(6.59)
52,0
(2.05)
28,4
(1.12)
162,5
(6.40)
71,0
(2.80)
19,0
(0.75)
70,6
(2.78)
for L.H. rotation
214,3
(8.44)
79,2
(3.12)
Load sensing
control port location
for L.H. rotation
77,0
(3.03)
for R.H. rotation
128,3
(5.05)
Load sensing com. control port for

R.H. rotation .4375-20 UNF-2B thd.
SAE O-ring boss connection .250
O.D. tubing
154,0
(6.06)
10,6
(0.42)
68,3
27,0 (2.69)
(1.06)
28,4
Max.
(1.12)
153,5
(6.04)
192,9
(7.59)
Caution: While pump is operating,

do not back out adjusting screw
beyond dimension shown.
PVQ25 CG Remote
Adjustment Compensator
196,6
(7.74)
167,5
(6.59)
52,0
(2.05)
162,5
(6.40)
186,1
(7.33)
28,4
(1.12)
75,1
(2.96)
114,8
(4.52)
153,5
(6.04)
38
15,1
(0.59)
58,4
(2.16)
for R.H. rotation
Load sensing com. control port for
R.H. rotation .4375-20 UNF-2B thd.
O.D. tubing
Ratings
Model
Series
Maximum Geometric
Displacement
cm3/r (in3/r)
Rated
Speed
r/min
Maximum
Pressure
bar (psi)
Input Power at Max.

kW (hp)
Approx.
Weight
kg (lb)
PVQ40
41,5 (2.500)
1800
210 (3000)
27,6 (37)
20,6 (45.4)
PVQ45
45,1 (2.750)
1800
186 (2700)
28,3 (38)
20,6 (45.4)
Pressure Limits
Note: Integral relief valve limits case pressure peaks to 0,7 bar (10 psi) higher
than inlet pressure to protect pump. Flow from valve is returned directly to pump
inlet. Use of case drain line required to limit steady-state case pressure.
Model Code
1
1
P
V
Q
2
Series PVQ
Inline piston pump
Variable volume
Quiet series
ratings
40 41, cc/rev (2.50 cir), 210 bar

(3000 psi)
45 45,1 cc/rev (2.75 cir), 186 bar
(2700 psi)
3

R
L
5

Thru-drive without coupling
(available with side ports only)
Blank
A9
A11
B26
6
No thru-drive
SAE J744 101-2 (SAE B) w/26T spline
SE SAE O-ring rear port, (standard)

SS SAE O-ring side port, (optional)
FS SAE 4-bolt, side ports (Preferred for
SAE A thru-drive. Not available on
SAE B thru-drive.)
7
1
2
3
4
Shafts, input
Straight keyed SAE B modified, 1.75
long (not available on thru-drive)
Straight keyed, SAE B-B modified
Splined SAE B modified, 13T
16/32 DP flat root side fit
Splined SAE B-B modified 15T

with MB mount only)
28 26 tooth splined shaft (Vickers). Used
in PVQ40/45 single to mount on
PVQ40/45 B26 thru-drive.
8
Seals
S
F
Buna N, standard
Pump design number

10
C**
4
Control type
Pressure compensator. PVQ40:

Standard model is C21, indicating
setting of 210 bar (3000 psi); range
is 0221 in tens of bar (3503000
psi). PVQ45: Standard model is
C19, indicating factory setting of
186 bar (2700 psi); range is 0219
CM** Low pressure compensator.
Standard model is CM7, indicating
factory setting of 70 bar (1000 psi);
range is 0210 in tens of bar
(3501500 psi).
C**V**B
1017 bar (150250 psi); with
C**V**P
orifice plugged.
10
11
12
13
C**VC**B

(250450 psi). With
bleed-down orifice.
C**VC**P Pressure compensator with
CG
Pressure compensator modified for
hydraulic remote control.
CD** Electric dual range compensator.
PVQ40: CD21 is standard 210 bar
setting of high range (24207 bar).
PVQ45: CD19 is standard 190 bar
setting of high range (24190 bar).
Both units require low range to be
set by customer (20100 bar).
UV
Unloading Valve for accumulator
circuits. See installation details.
11
Control option

D
stop (optional)
12
10
11
12
20
13
Control design
C** and CM**

C**D and CM**D
CD**, CG, and UV
Special suffixes
configurations.
39

is reached.

C & CM
This control automatically varies pump
displacement to meet the system flow
demand for a constant system pressure.
Displacement starts to reduce to zero
within 14 bar (200 psi) of the
compensator setting. Power draw-off is
minimized, therefore, system relief
valves should not be required.

CG
to approximately 3,4 bar (50 psi) below
being reduced.
C & CM

of 24 bar.
of 24 bar.

Displacement Stop D

Compensator CG
a remote pilot relief valve.

40
CD


Compensator Control

PVQ40 Model Series
Performance Data
Oil type:
SAE 10W
Inlet:
0 psi

100%
80%
210 bar (3000 psi)

140 bar (2000 psi)
70 bar (1000 psi)
35 bar (500 psi)
60%
40%
Overall efficiency
100%
140 bar (2000 psi)
70 bar (1000 psi)
80%
35 bar (500 psi)
210 bar (3000 psi)
60%
40%
USgpm
l/min
76
20
38
19
10
35 bar (500 psi)
70 bar (1000 psi)
140 bar (2000 psi)
210 bar (3000 psi)
0
hp
60
Input power
kW
45
45
30
15
Delivery
15
30
210 bar (3000 psi)

140 bar (2000 psi)
70 bar (1000 psi)
35 bar (500 psi)
500
15
1000
Speed r/min
1500
2000
Input power
Delivery
57
41
PVQ45 Model Series
Performance Data
Oil type:
SAE 10W
Inlet:
0 psi
100%
80%

140 bar (2000 psi)

70 bar (1000 psi)
35 bar (500 psi)
186 bar (2700 psi)
60%
100%
80%
35 bar (500 psi)

70 bar (1000 psi)
140 bar (2000 psi)
186 bar (2700 psi)
60%
USgpm
l/min
95
25
20
57
15
38
19
35 bar (500 psi)

70 bar (1000 psi)
140 bar (2000 psi)
186 bar (2700 psi)
10
0
hp
60
Input power
kW
45
45
30
15
42
Delivery
Delivery
76
30
186 bar (2700 psi)

140 bar (2000 psi)
70 bar (1000 psi)
35 bar (500 psi)
500
15
1000
Speed r/min
1500
2000
Input power
Overall efficiency
40%
Sound Data
Speed
r/min
Sound Level dB(A)**
Press re
Pressure
bar (psi)
Full Stroke
Cutoff
35 (500)
60
58
70 (1000)
65
65
61
60
62
62
140 (2000)
65
65
210 (3000)*
66
68
35 (500)
65
61
70 (1000)
67
64
140 (2000)
68
67
210 (3000)*
68
69
35 (500)
68
60
70 (1000)
69
65
140 (2000)
69
68
210 (3000)*
1800
65
70 (1000)
1500
61
63
35 (500)
1200
61
140 (2000)
210 (3000)*
1000
71
70
* PVQ40 at 210 bar (3000 psi) and PVQ45 at 186 bar (2700 psi)
**Sound pressure data equivalent to NFPA Standard.

Test Fluid:
URSA-ED (10W)
Response Data
Control Type
On stroke
Off stroke
0.050 sec.
0.020 sec.
0.040 sec.
0.010 sec.
43
Side Ports, C & CM Controls, No. 2 Shaft

Drain port D1 .875-14 UNF-2B thd. SAE
O-ring boss connection .625 O.D. tubing
Outlet port B see note.

1.3125-12 UN-2B thd. SAE
O-ring boss connection
1.000 O.D. tubing. Shown
for R.H. rotation.
Construction plug.
Do not remove.
191,00
(7.52)
41,56
(1.64)
95,25
(3.75)
50,04
(1.97)
97,28
(3.83)
194,56
(7.66)
25,37 (0.999)
25,35 (0.998)
34,04
(1.34)
20,32 (0.80)R
6,35 (0.250)
x 31.75 (1.250) Lg. key
6,38 (0.251)
58,67
(2.31)
120,65
(4.75)
28,22
(1.111)
27,97
(1.101)

for L.H. rotation.
25,4
(1.00)
25,45
Max.
(1.12)
Caution While pump is operating
do not back compensator
adjustment screw out
beyond dimension shown.
Plug shown for industrial
models.
14,22
(0.56)
176,28
(6.94)
Inlet port A see note.
1.87512 UN2B thd. SAE
for R.H. rotation
R.H.
Rotation
190,5
(7.50)
for L.H. rotation
for R.H. rotation
173,74
(6.84)
211,07
(8.31)
9,53
(.375)
118,11
(4.65)
86,87
(3.42)
28,45
(1.12)
56,90 (2.24)
101,6
(4.00)
101,5
(3.998)
73,03
(2.875)
146,05
(5.750)
Date of assembly
stamped on flange
44
93,2
(3.67)
55,63
(2.19)
63,5
(2.50)
95,76
(3.77)
12,7 (0.50)
Typ.
14,15
(0.557)
14,53
(0.572)
63,5
(2.50)
84,84
(3.34)
50,8
(2.00)
91,44
(3.60)
184,91
(7.28)
98,30
(3.87)
218,19
(8.59)
196,60
(7.74)
.875-14 UNF-2B thd. SAE
.625 O.D. tubing
52,83
(2.08)
Rear Ports
173,74
(6.84)
Inlet port A see note.

1.875-12 UN-2B thd. SAE
for R.H. rotation

for L.H. rotation.
86,87
(3.42)
47,7
(1.88)
47,7
(1.88)
91,4 96,8
(3.60) (3.81)
84,8
(3.34)
73,7
84,8 (2.90)
(3.34)
3
(0.12)

1.3125-12 UN-2B thd. SAE
for R.H. rotation

.625 O.D. tubing
221,2
(8.71)
No. 1 Shaft
3,8
(0.15) 91,4
(3.60)
No. 3 Shaft
44,45
(1.75)
No. 4 Shaft
45,97
(1.81)
44,45
(1.75)
25.12
22,225
(0.989) (0.8750)
24,87
22,200
(0.979) (0.8740)
6,375
(0.251) 31,75
x
lg. key
6,350 (1.250)
(0.250)
38,1
(1.50)
33.3
(1.31)
101,6 (4.00)
101,5 (3.99)
23,75
(0.935)
30_
1.5
x 45_
(0.06)
1,52
x 45_
(0.06)
9,52
(0.375)
33,32
(1.312)
9,4
(0.37)
Spline: SAE B Involute, 13T,

Spline: SAE B-B Involute,

15T, 16/32 DP flat root side fit
5,8
(0.23)

(Flange and shaft end ISO 3019/2-100A2HW-E25N)
10,50
(4.30)
100 (3.937)
99,95 (3.935)
42,0
(1.65)
Sq. key
8,00 (0.315)
7,96 (0.314)
28,01 (1.103)
27,71 (1.091)
11,27
(0.444)
25,006 (0.9845)
24,994 (0.9840)
9,25
(0.364)
70
(2.75)
140,0
(5.51)
45
C**V** Pressure Compensator

with Load Sensing

port location for R.H. rotation
O-ring boss connection .250
O.D. tubing
215,90
(8.50)
239,27
(9.42)
63,5
(0.250)
28,45
(1.12)
211,32
(8.32)
22,35
(0.88)
6,60
(2.6)
131,57
(5.18)
19,05
(0.75)
CG Remote Control
Load sensing control

port location for L.H.
rotation
50,8
(2.00)
10,92
(0.43)
74,68
(2.94)
118,88
(4.68)
79,25
(3.12)
Comp. control
port for L.H.
rotation
28,45
(1.12)
Max.
55,63
(2.19)
55,63
(2.19)
beyond 28,45 (1.12)
dimension shown while
pump is operating.
Comp. control port location for

R.H. rotation .4375-20
connection .250 O.D. tubing
46
Control with
Adjustable Maximum
Displacement Stop D
Adjustment
counter-clockwise (CCW) to increase
by tightening locknut. To assist initial
219,4
(8.64)
279,1
(10.99)
This control enables the maximum pump

compensated pump.
Note:
Not available with thru-drive models.
Maximum stop
adjusting screw
.250-20 UNC thd.
(Approx. cc/rev
change per turn:
PVQ40 3.22
PVQ45 3.55)
13,9
(0.59)
59,7
(2.35)
(screw flush with nut)
34
(1.34)
23,87
across flats
(0.94)

Do not back adj. knob
beyond 28,4 (1.12)
dimension shown while
pump is operating.
97,2
(3.83)
28,4
(1.12)
127,7
(5.03)
28,4
(1.12)
Max.
55,6
(2.19)
Locknut 11,7 (0.44)

across flats
47
Electric Dual Range

Stop CD**D
This control has the combined features
and adjustments of the CD control and
D control option. See preceding page
and following page for adjustment
procedures.
279,1
(10.99)
Solenoid Data
(110V AC 50 Hz and 115/120V AC 60 Hz)
Solenoid current
115/120V AC 60 Hz
110V AC 50 Hz
2 lead wires from

solenoid, approx. 152 mm
(6.00 in) long with M3 (#6)
size terminals provided for
customer connection.
219,4
(8.64)
Control position shown

for L.H. rotation
Inrush
amps
(R.M.S.)
Holding
amps
.54
.64*
2.0
15
(0.59)
* Maximum peak inrush amps approximately

1.4 x R.M.S. value shown.
Refer to catalog GB-C-2015B for

additional solenoid valve data.
Min. delivery
position (screw
flush with nut)
Control position
shown for R.H.
rotation


131,8
(5.19)
34
(1.34)
Max.
delivery
position
180,6
(7.11)
Max. stop adj. screw
(.250-20 UNC thd.)
73,41
(2.89)
17,53
(0.69)
Electrical conduit
connection
NPT thread
1/
2
Manual
actuator
Locknut
11,2 (0.44)
across flats
195,1
(7.68)
150,4
(5.92)
2. Locknut 17,3 (0.68)

across flats
3. Locknut must be
5. Locknut 31,7 (1.25)

across flats
48
55,6
(2.19)
218,9
(8.62)
Electric Dual Range

Control CD**
Adjustment
adjusting spool equals approximately
41 bar (600 psi). Energize solenoid
and check pressure setting.
De-energize solenoid and re-adjust if
necessary. Secure this setting by
tightening locknut 2.
214,6
(8.45)
268
(10.55)
312,7
(12.31)

335,2
(13.2)
2. Locknut 17,3 (0.68)

across flats
Manual
actuator
3. Locknut must be
Electrical conduit
connection
NPT thread

1/
2
5. Locknut 31,7 (1.25)

across flats
122,2
(4.81)
Solenoid Data
(110V AC 50 Hz and 115/120V AC 60 Hz)
Solenoid current
115/120V AC 60 Hz
110V AC 50 Hz
Inrush
amps
(R.M.S.)
2.0
* Maximum peak inrush amps approximately

1.4 x R.M.S. value shown.
Refer to catalog GB-C-2015B for

additional solenoid valve data.
Holding
amps
.54
.64*
Control position
shown for R.H.
rotation
83
(3.27)
190,2
(7.49)
55,6
(2.19)
Control position
shown for L.H.
rotation
2 lead wires from

solenoid, approx. 152 mm
(6.00 in) long with M3 (#6)
size terminals provided for
customer connection.

49

Unload valve
control port
To load
Inlet

Check Valve
Outlet
Drain
Setting Pressures
check valve.

Adjustment range
PVQ40 100210 bar (15003000 psi)
PVQ45 100186 bar (15002700 psi)


pressure, minimum.

Standby pressure
adjustment
pressure adjustment
219,4
(8.64)
145,5
(5.95)
184.9
(7.28)
74,7
(2.94)
91.4
(3.60)
50
55,6
(2.19)
A9 & A11 SAE A Thru-Drives

28,22
(1.11)
27,97
(1.10)
97,28
(3.83)
6,35 (0.251)
Sq. key
6,30 (0.250)
25,37
(0.999)
25,35
(0.998)
147,57
(5.81)
A (see table on next page)
Output spline see

thru-drive table on next
page
31,75
(1.25)
25,4
(1.00)
194,56
(7.66)
87,38
82,55
(3.44)
(3.253)
No. 2 shaft
50.8
(2.00)
58,67
(2.31)
151,13
(5.95)
191,26
(7.53)
38,1
(1.50)
101,6 (4.00)
101,5 (3.99)
12,7
(0.500)
28,45
(1.12)
Max.
Do not back out comp.

adjusting knob beyond
this dimension while
pump is operating.
45,97
(1.81)
22,61
(0.89)
Drain port D1. .875-14 UNF-2B thd.

O.D. tubing
1,42 (0.056)
1,32 (0.052)
12,7
(0.50)
50,8
(2.00)

O-ring boss connection .250
O.D. tubing

for L.H. rotation.
Inlet port A. See note

1.50 diameter inlet. SAE
J518 4-bolt flange.
Standard pressure series
.500-13 UNC-2B thd.
1.06 deep 4 places
84,84
(3.34)
.375-16 UNC-2B thd.

.88 deep 4 places
Outlet port B.
See note. 1.00
diameter inlet.
SAE J518 4-bolt
flange. Standard
pressure series
95,25
(3.75)
26,18
(1.031)
.375-16 UNC-2B
thd. .72 deep
2 holes
84,84
(3.34)
23,75
(0.935)
52,37
(2.062)
Outlet port B face
69,85
(2.75)
73,6
(2.90)
1,52 (0.06) x 45_

34,935
(1.375)
9,4
(0.37)
14,48
(0.57)
35,7
(1.406)
242,06
(9.53)
91,44
(3.60)
95,76
(3.77)
13,1
(0.516)
26,2
(1.031)
17,86
(0.703)
A flange
Alternate drain
port D2
53,09
(2.09)
91,95
(3.62)
105,43
(4.19)
91,95
(3.62)
51
B26 SAE B Thru-Drive

142,4
(5.61)
41,6
(1.64)

1.3125-12 UN-2B thd SAE O-ring
boss connection 1.00 O.D. tubing
191,0
(7.52)
A (see below)
5,8
(0.23)
98,5
No. 4 shaft
(3.88)
Modified
involute spline
SAE BB
197,3
(7.77)
1,52
(0.06)
x 45_
107,2 (4.221)
107,1 (4.219)
23,75
(0.935)
38,10
(1.500)
1,45 (0.057)
1.30 (0.051)
Drain port
176,3
(6.94)
45,9
(1.81)
Do not back out comp. adjusting knob

beyond this dimension while pump is
operating.
12,7
(0.50)
57,2
(2.25)

for L.H. rotation.
28,45
(1.12)
Max.

.250 O.D. tubing
9,7
(0.38)
14,5
(0.57)
No. 2 shaft
6,35
31,75
x
lg. key
(0.25) (1.250)
101,7 (4.003)
101,6 (4.001)
25,4
(1.00)
120,65
(4.75)
.500-13
UNC-2B thd
.88 deep
2 holes
Inlet port A see note. 1.875-12

UN-2B thd. SAE O-ring boss
connection 1.500 O.D. tubing
28,2 (1.110)
27,9 (1.100)
101,6
(4.00)
63,50
(2.50)
25,1
(0.999)
50,8
(2.00)
56,7
(2.31)
73,03
(2.875)
254,8
(10.03)
146,05
(5.750)
95,25
(3.75)
95,25
(3.75)
98,30
(3.87)
196,6
(7.74)
Max. Torque
Nm (in. lb.)
Dimension A
mm (in)
Coupling Type
Thru-drive
Coupling
ASA B5.15-1960
9 teeth 16/32 DP
Flat root side fit
58 (517)
10,92 (0.43)
9T/9T
864224
A11
ANS B92.1-1970
11 teeth 16/32 DP
Flat root side fit
118 (1050)
12,57 (0.495)
11T/11T
864325
24,89 (0.98)
26T/26T
627168
B26
Special Vickers
26 teeth 32/64 DP
Flat
Fl t root side fit
t id
10,92 (0.43)
26T/13T
864307
20,56 (0.81)
26T/15T
475134
Model Series
Spline Data
A9
179 (
(1587)
)
Note: Coupling, screws, and washers must be ordered separately to mount rear pump. A O-ring (AS568-042) and B O-ring (AS568-155) are
included with each thru-drive pump. Couplings for B26 are step type for 13 and 15 tooth as shown.
52
Thru-drive Shaft Torque Limits

Input Shaft Code
2
337 (2987)
215 (1900)
208 (1850)
337 (2987)
337 (2987)
215 (1900)
208 (1850)
337 (2987)
PVQ40/45B26
337 (2987)
PVQ40/45A11
208 (1850)
PVQ40/45A9
215 (1900)
Model Series
Maximum Input
Torque Total
Nm (lb. in.)
Maximum Thru-drive
Torque Output
Nm (lb. in.)
337 (2987)
58 (517)
123 (1100)
179 (1587)
Note: Both input and output limits must be met.
Typical Rear Pumps (with Shaft Codes) for

PVQ40/45 Thru-Drives
Model
Series
Rear Pump
Shaft Code
PVQ10/13
PVB5/6
S124 suffix
V10
11
V20
A9
Typical Rear Pump
Thru-drive
Coupling
62
864224
2
PVE12
864307
28
627168
864307
28
627168
864307
475134
28
627168
V2010 OR V2020
11
864307
20V
151
864307
2520V
166
475134
PVQ20/32
B26
PVQ40/45
Note: A11 (not listed above) is intended for special application only.
53
Thru-Drive Pump Support Bracket

An optional support bracket should be
used when a heavy second pump is
mounted to a thru-drive PVQ40 or
PVQ45. The support bracket (627179),
two screws (199740), and two washers
(427700) must be ordered separately.
171,45
(6.75)
11,68
(0.46)
147,83
(5.820)
10,41 (0.410)
2 holes
10,29 (0.405)
85,85
(3.38)
33,78
(1.33)
82,55
(3.25)
17,27
R
(0.68)
55,37
(2.18)
12,85 (0.506)
2 holes
12,73 (0.501)
19,05
(0.75)
19,05
(0.75)
19,05
(0.75)
28,575
(1.125)
54
114,30
(4.500)
28,575
(1.125)
85,85
(3.38)
PVQ63 Model Series
Ratings
Model Series
Maximum
Geometric
Displacement
cm3/r (in3/r)
Rated
Speed
r/min
Maximum
Pressure
bar (psi)
Input Power at
Max. Pressure &
Rated Speed
kW (hp)
Approx.
Weight
kg (lb)
PVQ63
63,0 (3.844)
1800
210 (3000)
47,5 (64)
63,0 (139)
Pressure Limits
Model Code
P
V
Q
2
R
L
Inline piston pump

Variable volume
Quiet series
FS Flange SAE side port

ratings
C2 Flange SAE C 2-bolt

4
Series PVQ
63 63,0 cc/rev (3.84 cir), 210 bar

(3000 psi)
3

Shafts, input
Straight keyed SAE C, long
Seals
Buna N, standard
Pump design number
10 Design (PVQ63 with EDG controls)

20 Design (PVQ63 with C** controls)
Design number subject to change.
unchanged for designs 1019 and
2029.
10
Control type
C**
Pressure compensator. Standard

model is C21, indicating setting of
210 bar (3000 psi); range is 0221
CG
Pressure compensator modified
for hydraulic remote control.
CGV6F Remote pressure compensator
with high response load sensing
control. Load sensing setting is
6 bar (87 psi) P, without
bleed-down orifice.
EDG
Direct electric displacement control
with remote pressure compensator.
10
Control design
10 CG, CGV6F, and EDG

11 C**
55
Control C
LS

maintained to approximately 3,4 bar (50
psi) below the pressure control before
being reduced. The pressure
compensator control operates on one
side of center and has an adjustment
range as designated in the model
coding.
P
R
Dr
Dr
CG
Load Sensing & Remote

Compensator Control CGV6F
Dr

Compensator CG
This compensator is the same as the
C compensator, except the machine
operator is able to change the
a remote pilot relief valve. The pump
must not be operated with the remote
compensator port plugged; the port
must be connected to a remote pilot
relief valve, such as Vickers C-175. The
effective compensator setting is the sum
of the compensator control setting and
the remote relief valve setting.
56
This control provides load sensing

to the desired maximum pressure
controlled by a remote relief valve. It
automatically adjusts pump flow in
response to a load pressure signal and
maintains outlet pressure at a level
approximately 6 bar (87 psi) above load
pressure. By venting the load sense line
with external valving when no flow or
pressure demands are placed on the
system, the pump will go to a no-flow,
low pressure, energy conserving
standby mode. A remote pressure relief
valve is required to override the load
sensing control, reducing pump
displacement as the preset maximum
operating pressure is reached.
CGV6F
The pumps outlet flow is used to stroke
the pump. An integral sequence valve
maintains a minimum outlet pressure of
10 bar (150 psi) to assure the necessary
control pressure is available. Controller
EDQ-L-30 is needed to drive the
proportional valve and provides the
appropriate interface for the LVDT.
Direct Electric Displacement

Control with Remote Pressure
Compensator EDG
This control varies pump flow from zero
to maximum displacement in response
to an input voltage of 05 volts. The
pump has an integral LVDT feedback
device that measures yoke position. The
electric control is overridden by a
remote pressure compensator. When
the system pressure reaches the remote
compensator relief valve setting, the
pump is destroked to the displacement
needed to maintain the selected
pressure.
POS
EDG

100%
Efficiency
Overall efficiency
80%
60%
Delivery l/min (USgpm)
Input power
40 (53.6)
Delivery
120 (31.7)
30 (40.2)
80 (21.1)
20 (26.8)
40 (10.5)

0
70
(1000)
140
(2000)
Input power Kw (hp)
50 (67.0)
40%
10 (13.4)
210
(3000)
Sound Data
Speed
r/min
Sound Level dB(A)*
Pressure
Press re
bar (psi)
Full Stroke
Cutoff
35 (500)
53
45
70 (1000)
59
58
56
46
58
56
140 (2000)
60
53
210 (3000)
62
59
35 (500)
59
50
70 (1000)
60
53
140 (2000)
63
60
210 (3000)
65
64
35 (500)
63
56
70 (1000)
65
60
140 (2000)
69
67
210 (3000)
1800
54
70 (1000)
1500
48
56
35 (500)
1200
54
140 (2000)
210 (3000)
1000
70
68

Test Fluid:
URSA-ED (10W)
57
Response Data
Control Type
On stroke
Off stroke
0.108 sec.
0.031 sec.
0.075 sec.
0.025 sec.
C Control
35,7
(1.40)
17,85
(0.70)
Outlet
30
port P (1.18)
M12
23
deep
(0.90)
69,8
(2.75)
34,9
(1.37)
Case drain port Dr.

1 1/16-12 UN
128
(5.04)
256
(10.08)
7,95 (0.3129)
Sq. Key
7,935 (0.3124)
78
(3.07)
+0
0,05
+0
(5.00)
0.002
127
295
(11.61)
R16
(R0.63)
60
(2.36)
9,5
(0.37)
57,2
(2.25)
14,5
(0.57)
260,5
(10.25)
Adj. screw
163,4
147 (6.43)
(5.79)
34,9
(1.37)
130
(5.12)
90,5
(3.56)
57,2
(2.25)
58
84
(3.31)
139,3
(5.48)
153,6
(6.05)
97,5
(3.84)
35,2 0,1
(1.385 0.004)
+0
31,75
0,05
+0
(1.25)
0.002
114
(4.50)
181
(7.12)
30
(1.18)
Max.
69,8
(2.75)
114,4
(4.50)
17,5
6
(0.69)
24
hex
(0.94)
35,7
(1.40)
252
(9.92)
Inlet
38
port I (1.50)
23
deep
M12
(0.90)
17,85
(0.70)
107
(4.21)
107
(4.21)
CGV6F Control
2,4
(0.09)
120
(4.72)
71
(2.79)
8
(0.31)
Max.
68
(2.68)
30
(1.18)
36,5
(1.44)
Unadjustable
60
(2.36)
Remote compensator port R

7/ - 20 UNF
16
36,5
(1.44)
14,5
(0.57)
9,5
(0.37)
194
(7.64)
Load sensing port LS

7/ -20 UNF
16
57,2
(2.25)
142
(5.59)
130
(5.12)
34,9
(1.37)
7,95 (0.3129)
Sq. Key
7,935 (0.3124)
177
(6.97)
114,4
(4.50)
35,2 0,1
(1.385 0.004)
90,5
(3.56)
181
(7.12)
17,5
6
(0.69)
57,2
(2.25)
69,8
(2.75)
+0
0,05
+0
(1.250)
0.002
31,75
Inlet
38
port I (1.50)
23
M12
deep
(0.90)
114,4
(4.50)
252
(9.92)
17,85
(0.70)
35,7
(1.40)
CG Control
128
(5.04)
256
(10.08)
Remote control port R

7/ -20 UNF
16
114,2
(4.50)
84,6
(3.33)
127+0
0,05
(5.00)
+0
0.002
8
(0.31)
Max.
39,5
(1.55)
Unadjustable
7,95 (0.3129)
Sq. Key
7,935 (0.3124)
60
(2.36)
9,5
(0.37)
78
(3.07)
Case drain port Dr.

11/16-12 UN
296
(11.65)
14,5
(0.57)
260
(10.25)
41
(1.61)
140
34,9 (5.51)
(1.37)
130
(5.12)
57,2
(2.25)
69,8
(2.75)
114,4
(4.50)
35,2 0,1
(1.385 0.004)
17,5
6
(0.69)
57,2
(2.25)
114,4
(4.50)
181
(7.12)
90,5
(3.56)
+0
0,05
+0
(1.250)
0.002
Inlet
38
port I (1.50)
31,75
23
deep
M12
(0.90)
252
(9.92)
17,85
(0.70)
35,7
(1.40)
59
EDG Control
Case drain port Dr.
11/16-12UN
+0
0,05
+0
(5.00)
0.002
127
Remote control port R

7/ -20 UNF
16
128
(5.04)
256
(10.08)
7,95 (0.3129)
Sq. Key
7,935 (0.3124)
Filling port
78
(3.07)
296
(11.65)
318
(12.52)
237,5 (9.35) Max.
Connector JIS C 5432

CNR01SPF 013 005
67
(2.64)
60
(2.36)
Outlet port P
11/16-12UN
57,2
(2.25)
8,5
(0.33)
Max.
14,5
(0.57)
Outlet port P1
11/16-12UN
9,5
(0.37)
241
(9.49)
34,9
69,8
(1.37) (2.75)
31,8
(1.25)
130
(5.12)
194
(7.64)
114,4
(4.50)
17,5
6
(0.69)
57,2
(2.25)
114,4
(4.50)
90,5
(3.56)
181
(7.12)
158
(6.22)
60
+0
0,05
+0
(1.250)
0.002
100,5
(3.96)
Inlet
38
port I (1.50)
31,75
35,2 0,1
(1.385 0.004)
23
M12
deep
(0.90)
35,7
(1.40)
252
(9.92)
17,85
(0.70)
107
(4.21)
107
(4.21)
158
(6.22)
209,5
(8.25)
EDQ-L-30 Amplifier/Controller
Schematic Block Diagram
200 mA (Q in <50 MV)
Jump
Mode
SW1
Qc
CP1**
Qe
CP2
X1
Q in
Q in
X0.5
Mode switch (SW1)
=1, Input demand 0-5V
=2, Input demand 0-10V
3
9V
VR3
V/I
CP4
0:1.27
1:1.46
2:1.63
3:1.82
4:2.00*
5:2.19
6:2.36
7:2.55
Gain
SW2
lm
CP7
PWM
SOL
+9V
Note: Limit time of mode switch at
4 to less than 15 minutes
VR9
Bias
P in
P in
0~1.0
Compensating value for internal
pump leakage proportional to
system pressure (optional).
VR11
DG
Qm
CP6
X0.2
VR13
DF
LV
CP5
50Hz
X1.0
CP8**
Ev
LVDT I/F
JP1
X1.2
60Hz
LVDT
(Installed in pump and
senses yoke position)
(JP1 switch selects frequency

set to 50Hz at factory)
* Factory setting
**CP1 and CP8 are observed as negative voltage.
VR5
Offset
VR6
Span
61
General Ratings
Item
Minimum
Typical
Maximum
Units
Vp=+24V
1.2
Idd
Vdd=+15V
80
mA
Iss
Vss=15V
60
mA
Mode SW=1
Mode SW=2
Dem nd Inp t
Demand Input
Condition
Ip
Power Current
Symbol
10
Qin
Jump Threshold
Qj
46
50
54
mV
Jump Value
Ij
Qin < Qj
220
200
180
mA
VR13=CCW
80
90
100
Delivery Adj.
115
120
125
VR13=CW
200
230
260
VR11=CCW
Delivery Adj.
280
300
VR11=CW
280
300
320
Bias=CCW
0.67
0.70
0.74
Delivery Adj.
0.95
1.00
1.05
Bias=CW
1.10
1.15
1.20
Io=1.0A
0.98
1.00
1.06
Gain=0
1.24
1.27
1.30
Gain=1
1.43
1.46
1.49
Gain=2
1.60
1.63
1.66
Gain=3
1.78
1.82
1.86
Gain=4
1.96
2.00
1.04
Gain=5
2.15
2.19
2.23
Gain=6
2.31
2.36
2.41
Gain=7
2.50
2.55
2.60
Dither Frequency
Dither Amplitude
Bias Current
Current Monitor
Proportion l Gain
Proportional G in
62
DF
DG
Bias
Im
Kp
Hz
mA
Installation Dimensions
Millimeters (inches)
OFF
SET
SPAN
180
(7.09)
CN3
170
(6.69)
CP9
VR5
CP5
(descriptions,
see next page)
1: PR1+
2: PR1
3: SEC+
4: SEC
5: SG
50Hz
60Hz
CP7
VR6
CP6
CP4
CP8
43
(1.69)
1
JP1
3
VR3
1: Qm
2: Qin+
3: Qin
4: Pin+
5: Pin
6: SG
150
(5.90)
CN2
CP3
GAIN
SW2
75
(2.95)
MODE
OC
SPAN
BIAS
CP1
CP2
SW1
VR9
CP10
VR11
5
(0.20)
53
(2.08)
VR13
20
(0.79)
9
(0.35)
96.5
(3.80)
40
(1.57)
(descriptions,
see next page)
1: Vss
Check Pins
CP1 (red):
Qc; value of demand after Mode switch (negative)
2: SG
CP2 (green):
Qe; difference between Qc and Qm
3: Vdd
CP3 (black):
SG; signal ground
4: Vp
CP4 (brown):
V/I; final control value
5: 0Vp
CP5 (blue):
LV; rectified secondary signal of LVDT
6: SOL+
CP6 (yellow):
Qm; yoke position (0 to 5V)
7: SOL
CP7 (white):
Im; voltage converted form output current (1A/1V)
CP8 (orange):
Ev; compensating value for internal leakage (negative)
CP9 (purple):
Losc; oscillation signal for LVDT (sine wave, 4 to 4.4 kHz)
CP10 (white):
Dosc; oscillation signal for dither (square wave, 120 Hz)
CN1
63
Connector Pin Assignment Descriptions

(from previous page)
Pin CN1
Pin Number
Symbol
Description
Vss
Power for signal process (15V)
SG
Return line of Vss and Vdd (signal ground)
Vdd
Power for signal process (+15V)
Vp
Power to drive solenoid coil (+24V)
0Vp
Return line of Vp (connected SG on the boad)
SOL+
Output to solenoid coil (+ side)
SOL*
Output to solenoid coil ( side)
* SOL is isolated from SG.
Pin CN2
Pin Number
Symbol
Description
Qm
Yoke position monitor (connected to CP6 on the boad)
Qin+
Demand input (+ side)
Qin*
Demand input ( side)
Pin+
Pressure signal input (+ side)
Pin
Pressure signal input ( side)
SG
Signal ground (connected to CP3 on the boad)
* Qin and Pin are isolated from SG.
Pin CN3
Pin Number
Symbol
Description
PRI+
Output to primary coil of LVDT (+ side)
PRI*
Output to primary coil of LVDT ( side)
SEC+
Input from secondary coil of LVDT (+ side)
SEC*
Input from secondary coil of LVDT ( side)
SG
Signal ground (connected to CP3 on the boad)
* PRI and SEC are isolated from SG.
Amplifier/Controller to LVDT Connection
2
4
Pump Side (LVDT)

64
Controller Side (CN3)
Application Data
Fluid Cleanliness
Proper fluid condition is essential for
long and satisfactory life of hydraulic
components and systems. Hydraulic
fluid must have the correct balance of
cleanliness, materials, and additives for
protection against wear of components,
elevated viscosity, and inclusion of air.
Essential information on the correct
methods for treating hydraulic fluid is
included in Vickers publication 561
Vickers Guide to Systemic
Contamination Control available from
your local Vickers distributor or by
contacting Vickers, Incorporated.

Recommendations on filtration and the
selection of products to control fluid
condition are included in 561.
Recommended cleanliness levels, using
petroleum oil under common conditions,
are based on the highest fluid pressure
levels in the system and are coded in
the chart below. Fluids other than
petroleum, severe service cycles, or
temperature extremes are cause for
adjustment of these cleanliness codes.
See Vickers publication 561 for exact
details.
Vickers products, as any components,

will operate with apparent satisfaction in
fluids with higher cleanliness codes than
those described. Other manufacturers
will often recommend levels above
those specified. Experience has shown,
however, that life of any hydraulic
component is shortened in fluids with
higher cleanliness codes than those
listed below. These codes have been
proven to provide a long, trouble-free
service life for the products shown,
regardless of the manufacturer.
System Pressure Level

bar (psi)
Product
<70 (<1000)
70-210 (1000-3000)
210+ (3000+)
Vane Pumps Fixed
20/18/15
19/17/14
18/16/13
Vane Pumps Variable
18/16/14
17/15/13
Piston Pumps Fixed
19/17/15
18/16/14
17/15/13
Piston Pumps Variable
18/16/14
17/15/13
16/14/12
Directional Valves
20/18/15
20/18/15
19/17/14
Pressure/Flow Control Valves
19/17/14
19/17/14
19/17/14
CMX Valves
18/16/14
18/16/14
17/15/13
Servo Valves
16/14/11
16/14/11
15/13/10
Proportional Valves
17/15/12
17/15/12
15/13/11
Cylinders
20/18/15
20/18/15
20/18/15
Vane Motors
20/18/15
19/17/14
18/16/13
Axial Piston Motors
19/17/14
18/16/13
17/15/12
Radial Piston Motors
20/18/14
19/17/13
18/16/13
65
Hydraulic Fluids and

Temperature Ranges
Use antiwear hydraulic oil, or
automotive type crankcase oil
designations SC, SD, SE or SF per SAE
J183FEB80.
Select a viscosity grade that will allow
optimum viscosity, between 40 cSt (180
SUS) and 16 cSt (80 SUS), to be
achieved within the optimum
performance envelope shown below.
For further information, see Vickers data
sheet B-920 or I-286-S.
Fire Resistant Fluids

All pumps can be used with water glycol
and polyol ester fluids. All except
PVQ16 and PVQ63 can be used with

phosphate ester fluids. All pumps can
be operated to 140 bar (2000 psi) with
these fluids, except PVQ13 and PVQ32
which are limited to 105 bar (1500 psi).
Input speed should not exceed 1800
r/min. System temperature should not
exceed 54 C (130 F). Inlet vacuum
should not exceed 101,6 millibar (3 in.
Hg). For more information, refer to
Vickers publication 579.
Installation and Start-up

(Commissioning)
Before a pump is started, fill the case
through the uppermost drain port with
hydraulic oil of the type to be used. The
case drain line must be connected to the
reservoir below oil level.
For multiple pump arrangements that

include non-PVQ sections, the
requirements of the non-PVQ units must
be considered.
Ordering Procedure
Order pumps by the full model
designation. Pump displacement,
mounting flange type, direction of
rotation, pump configuration, shaft end
type, seals, pressure adjustment range,
and specific control functions are all
specified in the full model code.
Couplings, O-rings, capscrews and
washers must be ordered separately for
all thru-drive pumps.
Viscosity
SUS
2300
cSt
500
Extreme performance envelope
Typical SAE 10W
viscosity grade oil
54
70
13
250
Optimum performance
envelope
20
10
50
_C
38
82
100
Temperature
65
150
180 _F

PVQ PDF

Uploaded by

Copyright:

Available Formats

PVQ PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PVQ PDF

Uploaded by

Copyright:

Available Formats

Vickers

PVQ Piston Pumps

PVQ piston pumps are in-line, variable

Vickers, Incorporated 1997

leads to reduced tendencies for noise in

package. Such a package offers lower

PVQ10 & PVQ13 Model Series

Input Power at Max.

Pump design number

Inline piston pump

10 Design number subject to change.

Displacement in cc/rev and pressure

Mounting flange specifications

Rotation viewed from shaft end

Ports, type and location

SE SAE O-ring rear port, 1.0625 inlet

A2 Flange SAE J744 82-2 (SAE A)

10 10,5 cc/rev (0.64 cir), 210 bar

Pressure compensator with

Blank Without adjustable maximum

C** and CM**

adjusts pump flow in response to a

Standard load-sense differential pressure

C**V11B Standard load-sensing and

Pressure Compensator with

Remote Control Pressure

Note: Graphic symbols shown with

Electric Dual Range Pressure

Load Sensing & Pressure

The dual range pressure compensator

C**V***B ({orifice open)

This compensator provides load sensing

PVQ10 Model Series

210 bar (3000 psi)

70 bar (1000 psi)

140 bar (2000 psi)

35 bar (500 psi)

140 bar (2000 psi)

210 bar (3000 psi)

210 bar (3000 psi)

PVQ13 Model Series

140 bar (2000 psi)

140 bar (2000 psi)

140 bar (2000 psi)

140 bar (2000 psi)

*Sound pressure data equivalent to NFPA Standard.

Temperature: 50C (120F)

Note: To ensure maximum noise

Rear Ports, C & CM Controls, No.1 Shaft

Outlet connection for R.H.

Caution: While pump is operating do

Case drain connection

Outlet connection for L.H. rotation

Outlet connection 1.3125-12

N Shaft with MA Flange

SAE standard involute spline flat root

Load Sensing with Pressure Limiting

2. Turn compensator adjustment plug to

Load sensing comp. control

C and CM

CV*B ({orifice open)