Tgs TGX GB

Guidelines to tting bodies
TRUCKNOLOGY
GENERATION
(TGS/TGX)
Edition 2013 Version 1.0
We reserve the right to make changes in the course of technical development.
2012 MAN Truck & Bus Aktiengesellschaft
Reprinting, reproduction or translation, even of excerpts, is not permitted without the written permission of MAN.
All rights, in particular under copyright, are strictly reserved by MAN.
Trucknology
and MANTED
are registered trademarks of MAN Truck & Bus AG

Where designations are trademarks they are, even without the
or sign, acknowledged as the proprietors protected marks.

P U B L I S H E R
MAN Truck & Bus AG
(mentioned in the text below MAN)
SMTST Depar t ment
Da c ha u e r St r . 6 6 7
D - 8 0 9 9 5 Mu n i c h
E- Mai l :
esc@man. eu
Fax:
+ 49 (0) 89 1580 4264
www. mant ed. de
TRUCKNOLOGY
GENERATION (TGS/TGX) I
1
1
1
1
2
2
3
3
4
7
8
8
10
10
11
11
11
11
12
13
14
17
18
22
26
26
27
28
28
29
31
32
34
TRUCKNOLOGY
GENERATION (TGS/TGX)
1. Applicability and legal agreements
1.1 Applicability
1.2 Legal agreements and approval procedure
1.2.1 Preconditions
1.2.2 Responsibility
1.2.3 Quality assurance
1.2.4 Approval
1.2.5 Submission of documents
1.2.6 Registration
1.2.7 Liability for defects
1.2.8 Product liability
1.2.9 Safety
1.2.10 Manuals from body and conversion companies
1.2.11 Limitation of liability for accessories/spare parts
2. Product designations
2.1 Vehicle designation and wheel formula
2.1.1 Door designation
2.1.2 Variant descriptor
2.1.3 Wheel formula
2.1.4 Sufx
2.2 Model number, vehicle identication number, vehicle number, basic vehicle number
2.3 Use of logos
2.4 Cabs
2.5 Engine variants
3. General
3.1 Axle overload, one-sided loading
3.2 Minimum front axle load
3.3 Wheels, rolling circumference
3.4 Permissible overhang
3.5 Theoretical wheelbase, overhang, theoretical axle centreline
3.6 Calculating the axle load and weighing procedure
3.7 Checking and adjustment procedures before and after body has been tted
3.8 Notes on MAN Hydrodrive
TRUCKNOLOGY
GENERATION (TGS/TGX) II
34
34
39
40
40
43
43
45
46
52
52
53
53
54
55
56
56
57
57
57
58
58
60
60
60
63
63
63
63
67
68
68
70
71
73
73
74
78
90
91
91
4. Modifying the chassis
4.1 Frame material
4.1.1 Subframe material
4.2 Corrosion protection
4.3 Drill holes, riveted joints and screw connections on the frame
4.4 Modifying the frame
4.4.1 Welding the frame
4.4.2 Modifying the frame overhang
4.4.3 Modications to the wheelbase
4.5 Retrotting additional equipment add-on components or accessories
4.5.1 Retrotting additional or larger fuel tanks after factory delivery
4.6 Propshafts
4.6.1 Single joint
4.6.2 Jointed shaft with two joints
4.6.3 Three-dimensional propshaft layout
4.6.3.1 Propshaft train
4.6.3.2 Forces in the propshaft system
4.6.4 Modifying the propshaft layout in the driveline of MAN chassis
4.7 Modifying the wheel formula
4.7.1 Safety-related components
4.8 Coupling devices
4.8.1 Basics
4.8.2 Trailer coupling, D value
4.9 Tractor units and converting the vehicle type - truck / tractor
4.9.1 Articulated vehicles
4.9.2 Converting trucks into tractor units or tractor units into trucks
4.10 Modifying the cab
4.10.1 General
4.10.2 Spoilers, roof extensions, roofwalk
4.10.3 Roof sleeper cabs
4.11 Add-on frame components
4.11.1 Rear underride guard
4.11.2 FUP - front underride protection
4.11.3 Sideguards
4.12 Modications to engine systems
4.12.1 Modications to the air intake system
4.12.2 Modications to exhaust gas routing for engines
4.12.3 Modications to the AdBlue
system
4.12.4 Engine cooling
4.12.5 Engine encapsulation, noise insulation
4.13 Fitting other manual gearboxes, automatic transmissions and transfer boxes
TRUCKNOLOGY
GENERATION (TGS/TGX) III

91
91
93
95
96
97
97
97
97
98
101
101
102
105
108
108
108
109
117
118
119
119
122
124
125
126
136
136
137
5. Bodies
5.1 General
5.1.1 Machinery Directive
5.1.2 CE marking
5.1.3 Afxing the hazardous goods marker board to the front panel
5.3 Subframes
5.3.1 General
5.3.2 Permissible materials, yield points
5.3.3 Subframe design
5.3.4 Attaching subframes and bodies
5.3.5 Screw connections and riveted joints
5.3.6 Flexible connection
5.3.7 Rigid connection
5.4 Bodies
5.4.1 Testing of bodies
5.4.2 Platform and box bodies
5.4.3 Tail-lifts
5.4.4 Interchangeable containers
5.4.5 Self-supporting bodies without subframe
5.4.6 Single-pivot body
5.4.7 Tank and container bodies
5.4.8 Tippers
5.4.9 Set-down, sliding set-down and sliding roll-off tippers
5.4.10 Propping air-sprung vehicles
5.4.11 Loading cranes
5.4.12 Cable winches
5.4.13 Transport mixers
5.4.14 Car transporter
TRUCKNOLOGY
GENERATION (TGS/TGX) IV
138
138
138
138
138
139
140
140
143
143
144
146
146
146
147
147
148
148
148
148
149
150
6. Electrics, electronics, wiring
6.1 General
6.2 Routing cables, earth cable
6.3 Handling batteries
6.3.1 Handling and maintaining the batteries
6.3.2 Handling and maintaining batteries with PAG technology
6.4 Additional wiring diagrams and wiring harness drawings
6.5 Fuses, additional power consumers
6.6 Lighting installations
6.7 Electromagnetic compatibility
6.8 Radio equipment and aerials
6.9 Interfaces on the vehicle, preparations for the body
6.9.1 Electrical connections for tail-lifts
6.9.2 Engine start-stop system
6.9.3 Tapping into the speed signal
6.9.4 Tapping into the reverse gear signal
6.10 Electronics
6.10.1 Display and instrumentation concept
6.10.2 Diagnostics concept and parameterisation using MAN-cats
6.10.3 Parameterisation of the vehicle electronics

6.10.4 ESP yaw rate sensor
6.10.5 Emergency Brake Assist
TRUCKNOLOGY
GENERATION (TGS/TGX) V
153
153
153
153
153
154
155
157
157
158
158
158
159
160
161
161
161
162
166
167
169
170
173
175
175
178
180
181
181
181
183
7. Power take-off (See separate booklet)
8. Brakes, lines
8.1 ALB, EBS braking system
8.2 Brake and compressed air lines
8.2.1 Basic principles
8.2.2 Voss 232 system plug connectors
8.2.3 Installing and attaching lines
8.2.4 Compressed air loss
8.3 Connecting additional air consumers
8.4 Retrotting continuous brakes not manufactured by MAN
9. Calculations
9.1 Speed
9.2 Efciency
9.3 Tractive force
9.4 Gradeability
9.4.1 Distance travelled on uphill or downhill gradients
9.4.2 Angle of uphill or downhill gradient
9.4.3 Calculating the gradeability
9.5 Torque
9.6 Power output
9.7 Rotational speeds for power take-offs at the transfer case
9.8 Driving resistances
9.9 Turning circle
9.10 Axle load calculation
9.10.1 Performing an axle load calculation
9.10.2 Calculation of weight with trailing axle lifted
9.11 Support length for bodies without subframes
9.12.1 Trailer coupling
9.12.2 Rigid drawbar trailers / central axle trailers
9.12.3 Fifth-wheel coupling
The ESC numbers stated in the illustrations are purely for internal reference.
They are of no consequence to the reader.
If not otherwise stated: all dimensions in mm, all weights and loads in kg.
TRUCKNOLOGY
GENERATION (TGS/TGX) 1
1. Applicability and legal agreements
1.1 Applicability
The statements in this guide are binding. If technically feasible, exceptions will be approved only if a written request has been
submitted to MAN, (for address see Publisher above).
1.2 Legal agreements and approval procedure
1.2.1 Preconditions
In addition to this Guide, the company carrying out the work must observe all
laws and decrees
accident prevention regulations
operating instructions
relating to the operation and construction of the vehicle. Standards are technical standards; they are therefore minimum requirements.
Anyone who does not endeavour to observe these minimum requirements is regarded as operating negligently.
Standards are binding when they form part of regulations.
Information given by MAN in reply to telephone enquiries is not binding unless conrmed in writing. Enquiries are to be directed to
the relevant MAN department. Information refers to conditions of use that are usual within Europe. Dimensions, weights and other basic
data that differ from these must be taken into consideration when designing the body, mounting the body and designing the subframe.
The company carrying out the work must ensure that the entire vehicle can withstand the conditions of use that it is expected
to experience.
For certain types of equipment, such as loading cranes, tail-lifts, cable winches etc, the respective manufacturers have developed
their own body regulations. If, when compared with this MAN Guide, they impose further conditions, then these too must be observed.
References to
legal stipulations
accident prevention regulations
decrees from professional associations
work regulations
other guidelines and sources of information
are not in any way complete and are only intended as ideas for further information.
They do not replace the companys obligation to carry out its own checks.
Fuel consumption is considerably affected by modications to the vehicle, by the body and its design and by the operation of equipment
driven by the vehicles engine. It is therefore expected that the company carrying out the work implements a design that facilitates
the lowest possible fuel consumption.
TRUCKNOLOGY
1.2.2 Responsibility
The responsibility for proper
design
production
installation of bodies
modication to the chassis
always lies fully with the company that is manufacturing the body, installing it or carrying out modications (manufacturers liability).
This also applies if MAN has expressly approved the body or the modication. Bodies/conversions that have been approved in writing
by MAN do not release the body manufacturer from his responsibility for the product. Should the company carrying out the work detect
a mistake either in the planning stage or in the intentions of
the customer
the user
its own personnel
the vehicle manufacturer
then that mistake must be brought to the attention of the respective party.
The company is responsible for seeing that the vehicles
operational safety
trafc safety
maintenance possibilities and
handling characteristics
do not exhibit any disadvantageous properties.
With regard to trafc safety, the company must operate in accordance with the state of the art and in line with the recognised rules in
the eld in matters relating to
the design
the production of bodies
the installation of bodies
the modication of chassis
instructions and
operating instructions.
Difcult conditions of use must also be taken into account.
1.2.3 Quality assurance
In order to meet our customers high quality expectations and in view of international product/manufacturer liability legislation an
on-going quality monitoring programme is also required for conversions and body manufacture/installation. This requires a functioning
quality assurance system. It is recommended that the body manufacturer sets up and provides evidence of a quality system that
complies with the general requirements and recognised rules (e.g. DIN EN ISO 9000 et seq. or VDA 8).
Evidence of a qualied system can be provided for example by:
TRUCKNOLOGY
If MAN is the party awarding the contract for the body or conversion evidence of qualication will be requested.
MAN reserves the right to carry out its own system audit in accordance with VDA 8 or a corresponding process check at the suppliers
premises. VDA volume 8 has been agreed with the following body manufacturers associations:
ZKF (Zentralverband Karosserie- und Fahrzeugtechnik Central Association of Body and Vehicle Engineering) and
BVM (Bundesverband Metall Vereinigung Deutscher Metallhandwerke Federation of German Metal Trades Associations).
It has also been agreed with the ZDH (Zentralverband des Deutschen Handwerks Central Association of German Craft Trades).
Documents:
VDA Volume 8
Minimum quality assurance requirements for trailer, body manufacturers, obtainable from the Verband der Automobilindustrie e.V
(VDA) (German Engine Industry Association), http://www.vda-qmc.de.
1.2.4 Approval
Approval from MAN for a body or a chassis modication is not required if the bodies or modications are carried out in accordance with
this Guide. If MAN approves a body or a chassis modication, then this approval refers
In the case of bodies only to the bodys fundamental compatibility with the respective chassis and the interfaces to the body
(e.g. dimensions and mounting of the subframe)
In the case of chassis modications only to the fact that, from a design point of view, the modications to the chassis in
question are fundamentally permissible.
The approval note that MAN enters on the submitted technical documents does not indicate a check on the
Function
Design
Equipment of the body or the modication.
Observance of this Guide does not free the user from responsibility to perform modications and manufacture bodies properly from
a technical point of view. The approval note only refers to such measures or components as are to be found in the submitted technical
documents.
MAN reserves the right to refuse to issue approvals for bodies or modications, even if a comparable approval has already been issued.
Later submissions for approval are not automatically treated the same as earlier ones, because technical advances achieved in
the interim period have to be taken into account.
MAN also reserves the right to change this Guide at any time or to issue instructions that differ from this Guide for individual chassis.
If several identical chassis have the same bodies or modications MAN can, to simplify matters, issue a collective approval.
1.2.5 Submission of documents
Documents should only be sent to MAN if bodies/conversions diverge from this Guide. Before work begins on the vehicle, technical
documents that require approval or inspection must be sent to MAN (for address see Publisher above).
For an approval process to proceed swiftly, the following are required:
Documents should be submitted in duplicate
The number of individual documents should be kept to a minimum
All the technical data and documents must be submitted.
TRUCKNOLOGY
The following information should be included:
Vehicle model (see Chapter 2.2 for model code) with
- cab design
- wheelbase
- frame overhang
Vehicle identication number or vehicle number (if already available, see Chapter 2.2)
Identication of deviations from this Guide to Fitting Bodies in all documentation!
Loads and their load application points:
- Forces from the body
- Axle load calculation
Special conditions of use:
Subframe:
- Material and cross-sectional data
- Dimensions
- Type of section
- Arrangement of cross members in the subframe
- Special features of the subframe design
- Cross-section modications
- Additional reinforcements
- Upsweeps, etc.
Means of connection:
- Positioning (in relation to the chassis)
- Type
- Size
- Number.
The following are not sufcient for inspection or approval:
Parts lists
Brochures
Photographs
Other not binding information.
Drawings are only valid if they bear the number that has been assigned to them. It is therefore not permitted to draw in the bodies or
modications on chassis drawings that have been provided by MAN and to submit these for approval.
1.2.6 Registration
National legislation on the registration of modied vehicles shall be complied with.
Modications made to the chassis shall be presented to a technical vehicle inspection centre for approval.
The company carrying out the work shall remain responsible, also after registration of the vehicle, should the competent authorities issue
a registration certicate with a lack of knowledge relating to the operational safety of the product.
TRUCKNOLOGY
Multi-stage co-operation modules in accordance with 2007/46/EC
I. Process
In line with the multi-stage process in accordance with Annex XVII of Directive 2007/46/EC each manufacturer is responsible for
the approval and conformity of production of all systems, components or separate technical units manufactured by him or added by him
to the previously built stage.
In accordance with 2007/46/EC the bodybuilder is a manufacturer in the second or further production stage.
II. Responsibilities
The bodybuilder shall always remain responsible:
For modications made by him to the basic vehicle.
For parts already approved at an earlier stage if modications made to the basic vehicle cause the approvals issued earlier
for this vehicle to be no longer applicable.
For ensuring that modications he has carried out comply with the corresponding national/international legislation,
in particular those of the target country.
For ensuring that modications he has carried out are presented to a technical vehicle inspection centre for approval.
For ensuring that compliance with legislation is documented in a corresponding manner (test report and/or approval or
other documentation in accordance with the legal requirements of the target country).
MAN, as the manufacturer of the basic vehicle, shall always remain responsible:
For providing upon request by the bodybuilder the available homologation documentation (EC/ECE approvals)
for the scope of supply of the basic vehicle in electronic form.
III. Identication of the vehicle
The respective vehicle shall be given a vehicle identication number (VIN) which MAN issues as the manufacturer of the incomplete
basic vehicle.
The requirements set forth in Annex XVII to Directive 2007/46/EC and the associated procedure instructions published together
with it shall always apply.
IV. Conformity of production (CoP)
The requirements set forth in the specic EC Directives and Annex X to Directive 2007/46/EC together with the requirements set forth in
Annex 2 to the ECE Agreement of 1958 shall always apply.

V. Provision of documentation for registration/the subsequent build stages
In accordance with Annex XVII to Directive 2007/46/EC MAN, as manufacturer of the basic vehicle, shall provide the bodybuilder(s) with
the available EC/ECE system approvals together with the Certicate of Conformity (CoC)
1)
available for the basic vehicle in electronic form.
1)
Only if the vehicle is EG-compliant and MAN has printed a CoC.
Case 1: Registration in Germany
If MAN serves as general contractor (single invoice transactions) the bodybuilder(s) is/are under an obligation,
as manufacturer of the second stage(s), to provide the following documentation in electronic form:
Case A: The specic conditions of delivery provide for the acceptance/approval and registration process to be carried
out by the vehicle manufacturer (MAN).
1. In the case of an existing and valid whole vehicle type-approval in accordance with 2007/46/EC
for the manufacturing stages, a CoC.
2. Alternatively to 1: The test reports and approval documentation required for national individual approval procedures
in accordance with Section 13 of the EC vehicle approval Directive.
TRUCKNOLOGY
The latest time for submitting the above stated documentation in printable form is the day the completed vehicle is returned to
the contractually agreed place of delivery.
The documentation shall be sent to the following e-mail address: documents@de.man-mn.com.
In cases where MAN receives a CoC from the bodybuilder, then original certicates may only be generated by MAN on behalf
of the bodybuilder.
Case B: The acceptance/approval and registration process is to be carried out by the contract partner
or by the manufacturer of the nal completion stage of the vehicle.
1. None. The registration process is the responsibility of the contract partner or the manufacturer of the nal completion
stage of the vehicle.
In all other cases the acceptance/approval and registration process is to be carried out by the manufacturer of the nal completion stage
of the vehicle or by the corresponding contract partner.
Case 2: Registration outside Germany but inside the area of application of Directive 2007/46/EC
If MAN serves as general contractor then the bodybuilder is under an obligation, as the nal stage manufacturer, to provide in
electronic form, all the necessary approval/registration documentation for all modications made during the subsequent
manufacturing stages of the respective responsible sales organisation or importer which exceed the scope of the basic vehicle.
Irrespective of any general contractor status of the importers, the acceptance/approval and registration process is to be carried out
by the manufacturer of the nal completion stage of the vehicle or by the corresponding contract partner.
The importer in the respective country or the corresponding contract partner have the authority and responsibility
for the registration process.
MAN does not provide national data for registration purposes that exceeds that for incomplete vehicles set forth in Annex IX to Directive
2007/46/EC in its current form and as amended from time to time. This also applies in particular to national model codes and encrypted
basic technical data.
MAN as a manufacturer reserves the right following corresponding feasibility studies and economic implementation and after
reaching corresponding specically applicable agreements with national sales organisations and importers, to provide data for national
registration which exceeds the scope of that set forth above (e.g. vehicles manufacturing plates etc.).
Corresponding enquiries shall be sent to the following e-mail address: documents@de.man-mn.com
VI. Condentiality agreement
The bodybuilder may not forward the approval documentation provided by MAN to any third parties without obtaining prior,
express permission from MAN.
The forwarding of documentation that is directly associated with the registration of the vehicle in question to persons of the institutions
listed below is excepted:
MAN sales partners
Technical vehicle inspection centres or testing organisations
Approving authorities
Registration authorities or licensing centres acting for the government
TRUCKNOLOGY
Type approval/homologation for
TiB (Truck in the Box),
CiB (Chassis in the Box),
BiB (Bus in the Box),
CKD (Complete Knocked Down),
SKD (Semi Knocked Down),
PKD (Partly Knocked Down)
For these versions MAN is not considered to be the manufacturer within the meaning of Directive 2007/46/EC therefore,
the responsibility for the homologation and registration process lies with the manufacturer of these vehicles.
In principle, the substance of the contracts respectively concluded with MAN shall apply.
In principle, MAN does not provide registration-related data for completed vehicles. Exceptions include homologation documentation
for components subject to approval such as the engine. Such documentation will be provided by MAN in electronic form.
This does not however, preclude MAN from reserving the right following corresponding feasibility studies and economic
implementation and after reaching corresponding specically applicable agreements with national sales organisations and importers,
from providing data for national registration which exceeds the scope of that set forth above (e.g. vehicles manufacturing plates etc.).
Corresponding enquiries shall be sent to the homologation department at MAN.
1.2.7 Liability for defects
Liability claims in respect of defects only exist within the framework of the purchasing contract between buyer and seller.
In accordance with this, liability for defects lies with the respective seller of the goods.
Claims against MAN are not valid if the fault that is the subject of the complaint was due to the fact that
This Guide was not observed
In view of the purpose for which the vehicle is used, an unsuitable chassis has been selected
The damage to the chassis has been caused by
- the body
- the type of body mounting or how the body has been mounted
- the modication to the chassis
- improper use.
TRUCKNOLOGY
1.2.8 Product liability
Any faults in the work that are identied by MAN are to be corrected. Insofar as is legally permissible, MAN disclaims all liability,
in particular for consequential damage.
Product liability regulates:
The liability of the manufacturer for its product or component
The compensation claim made by the manufacturer against whom a claim has been made against the manufacturer of
an integral component, if the damage that has occurred is due to a fault in that component.
The company that has made the body or carried out the modication is to relieve MAN of any liability to its customer or other third party
if the damage that has occurred is due to the fact that
The company did not observe this Guide
The body or chassis modication has caused damage on account of its faulty
- design
- manufacture
- installation
- instructions
The fundamental rules that are laid down have not been complied with in any other way.
1.2.9 Safety
In order to ensure operational reliability and road safety and to maintain the validity of the warranty, the bodybuilder must observe
the instructions given in these guidelines exactly. MAN shall not be liable for non-compliance.
Before commencing work on the body, making modications or starting installation work, the bodybuilder must also have knowledge
of the sections of the operators manual that relate to the work he is completing. It will otherwise be impossible to recognise risks and
other persons may be endangered.
MAN cannot be liable for reliability, safety and suitability if:
Bodies are not designed and tted in accordance with these guidelines
Original parts or approved parts are replaced with other parts
Unauthorised modications are made to the vehicle
Approvals by third parties, for example Technical Inspection Agencies or approvals from public authorities, shall not be considered
sufcient for precluding safety risks.
TRUCKNOLOGY
Companies carrying out work on the chassis/vehicle are liable for any damage that may be caused by poor functional and operational
safety or inadequate operating instructions. Therefore, MAN requires the body manufacturer or vehicle conversion company to:
Ensure the highest possible safety, in line with the state of the art
Provide comprehensible, sufcient operating instructions
Provide permanent, easily visible instruction plates on hazardous points for operators and/or third parties
Observe the necessary protection measures (e.g. re and explosion prevention)
Provide full toxicological information
Provide full environmental information.
Safety is top priority! All available technical means of avoiding incidents that will undermine operational safety are to be implemented.
This applies equally to
Active safety = prevention of accidents. This includes:
- Driving safety achieved by the overall vehicle design, including the body
- Safety as a consequence of the drivers well-being achieved by keeping occupant stress caused by vibrations,
noise, climatic conditions etc. to a minimum
- Safety as a consequence of observation and perception, in particular through the correct design of lighting systems,
warning equipment, providing sufcient direct and indirect visibility
- Safety as a consequence of operating equipment and controls this includes optimising the ease of operation of all
equipment, including that of the body.
Passive safety = avoidance and reduction of the consequences of accidents. This includes:
- Exterior safety such as the design of the outside of the vehicle and body with respect to deformation behaviour and
the installation of protective devices
- Interior safety including the protection of occupants of vehicles and cabs that are installed by the body builders.
Climatic and environmental conditions have effects on:
Operational safety
Readiness for use
Operational performance
Service life
Cost-effectiveness.
Climatic and environmental conditions are, for example:
The effects of temperature
Humidity
Aggressive substances
Sand and dust
Radiation.
Sufcient space for all parts required to carry out a movement, including all pipes and cables, must be guaranteed. The operating
instructions for MAN trucks provide information about the maintenance points on the vehicle. Regardless of what type of body is tted,
good access to the maintenance points must be ensured in all cases. It must be possible to carry out maintenance unhindered and
without having to remove any components. Sufcient ventilation and/or cooling of the components is to be guaranteed.
TRUCKNOLOGY
1.2.10 Manuals from body and conversion companies
In the event of a body being added or modications to the vehicle being carried out, the operator of the vehicle is also entitled to receive
operating instructions from the conversion company. All specic advantages offered by the product are of no use if the customer is
not able to:
Handle the product safely and properly
Use it rationally and effortlessly
Maintain it properly
Master all of its functions.
As a result, every vehicle body builder and converter must check his technical instructions for:
Clarity
Completeness
Accuracy
Comprehensibility
Product-specic safety instructions.
Inadequate or incomplete operating instructions carry considerable risks for the user. Possible effects are:
Reduced benet, because the advantages of the product remain unknown
Complaints and annoyance
Faults and damage, which are normally blamed on the chassis
Unexpected and unnecessary additional cost through repairs and time lost
A negative image and thereby less inclination to buy the same product or brand again.
Depending on the vehicle body or modication, the operating personnel must be instructed about operation and maintenance.
Such instruction must also include the possible effects on the static and dynamic performance of the vehicle.
1.2.11 Limitation of liability for accessories/spare parts
Accessories and spare parts that MAN has not manufactured or approved for use in its products may affect the trafc safety and
operational safety of the vehicle and create hazardous situations. MAN (or the seller) accepts no liability for claims of any kind resulting
from a combination of the vehicle together with an accessory that was made by another manufacturer, regardless of whether MAN (or
the seller) has sold the accessory itself or tted it to the vehicle (or the subject of the contract).
TRUCKNOLOGY
2. Product designations
2.1 Vehicle designation and wheel formula
To enable unique and easily comprehensible identication of the different variants new vehicle designations have been systematically
introduced. The vehicle designation system is based on three levels:
- Door designation
- Variant descriptor (in the sales and technical documentation e.g. data sheets, chassis drawings)
- Model code.
2.1.1 Door designation
The door designation comprises:
Model range + permissible weight + engine power
TGX 18.400
Model range + Permissible weight + Engine power
T GX 1 8 . 4 0 0
Abbreviated notation of model range TGX = Trucknology
Generation X,
technically permissible weight in [t],
engine power [DIN-hp] rounded to the nearest 10hp
2.1.2 Variant descriptor
The variant descriptor = vehicle designation which comprises the door designation + wheel formula + sufx.
The terms wheel formula and sufx are dened in the following sections.
Model range + permissible weight + engine power + wheel formula + sufx
TGS 24.480 6x2-2 LL-U
Model range + Permissible weight + Engine power
T GS 2 4 . 4 8 0 6 x 2 - 2 L L - U
Wheel formula Sufx
TRUCKNOLOGY
2.1.3 Wheel formula
The wheel formula stipulates the number of axles and provides additional identication of drive, steered and leading/trailing axles.
Wheel formula is a commonly used, but not standardised term. It is wheel locations that are counted and not the individual wheels.
Twin tyres are therefore regarded as one wheel.
The following two examples illustrate the wheel formula:
Table 1: Wheel formula examples
6 x 2 - 4
6 x 2 / 4
6 = Total number of wheel locations, i.e. 3 axles
x = No function
2 = Number of driven wheels
- = Trailing axle behind the rear drive-axle assembly
/ = Leading axle ahead of the rear drive-axle assembly
4 = Number of steered wheels
The number of steered wheels is only stated if, aside from steered front wheels, leading axles or trailing axles are also involved.
A leading axle is located ahead of a rear drive-axle assembly and a trailing axle is behind the rear drive-axle assembly.
A slash / represents a leading axle and a hyphen - represents a trailing axle.
If a chassis is tted with both leading and trailing axles the number of steered wheels follows the hyphen -.
If the vehicle is tted with MAN HydroDrive
hydrostatic front axle drive then the wheel formula receives an additional H,
e.g. 6x4H = a front axle with MAN HydroDrive
, 2 rear axles, one of which is driven.

Currently the following wheel formulae are available ex-works:
Table 2: TGS and TGX wheel formulae
4x2 Two-axle vehicle with one drive axle
4x4 Two-axle vehicle with two drive axles All-wheel drive
4x4H Two-axle vehicle with two drive axles, front axle with MAN HydroDrive
6x2/2 Three-axle vehicle with non-steered Pusher leading axle

6x2/4 Three-axle vehicle with steered leading axle
6x2-2 Three-axle vehicle with non-steered trailing axle
6x2-4 Three-axle vehicle with steered trailing axle
6x4 Three-axle vehicle with two driven non-steered rear axles
6x4-4 Three-axle vehicle with 2 driven axles, (rst and second axles), steered trailing axle
6x4H/2 Three-axle vehicle with MAN HydroDrive
front axle drive, one driven rear axle, non-steered leading axle
6x4H/4 Three-axle vehicle with MAN HydroDrive
front axle drive, one driven rear axle, steered leading axle
6x4H-2 Three-axle vehicle with MAN HydroDrive
-front axle drive, one driven rear axle, non-steered trailing axle
6x4H-4 Three-axle vehicle with MAN HydroDrive
front axle drive, one driven rear axle, steered trailing axle
TRUCKNOLOGY
Table 2: TGS and TGX wheel formulae (continuation)
6x6 Three-axle vehicle with all-wheel drive
6x6H Three-axle vehicle with all-wheel drive, front axle with MAN HydroDrive
8x2-4 Four-axle vehicle with one drive axle, two steered front axles, non steered trailing axle
8x2-6 Four-axle vehicle with one drive axle, two steered front axles, steered trailing axle
8x4 Four-axle vehicle with two steered front axles and two driven rear axles
8x4/4 Four-axle vehicle with one front axle, one steered leading axle and two driven rear axles
8x4-4 Four-axle vehicle with one front axle, two driven rear axles and one steered trailing axle
8x4H-6 Four-axle vehicle with two steered front axles (2nd front axle with MAN HydroDrive
), one driven rear axle and a steered

trailing axle
8x6 Four-axle vehicle All wheel drive with two front axles (2nd driven) and two driven rear axles
8x6H Four-axle vehicle All wheel drive with two front axles (2nd front axle with MAN HydroDrive
) and two driven rear axles

8x8 Four-axle vehicle All wheel drive with two front axles and two rear axles, all driven
2.1.4 Sufx
The sufx to the vehicle designation denes the type of suspension, differentiates trucks from tractor units and describes special
product features.
T GX 2 5 . 4 8 0 6 x 2 - 2 LL-U
Sufx
Types of suspension (Digits 1 and 2 of sufx)
Table 3: Types of suspension
BB Leaf suspension on front axle(s), leaf suspension on rear axle(s)
BL Leaf suspension on front axle(s), air suspension on rear axle(s)
LL Air suspension on front axle(s), air suspension on rear axle(s)
Semitrailer tractor units are designated with an S sufx. Trucks have no special designation.
Example for semitrailer tractor:
T GS 3 3 . 4 4 0 6 x 6 BBS
S = Semitrailer tractor
TRUCKNOLOGY
Special product (design) features are added separately following a hyphen - after the rst section of the sufx:
Example for special product features:
T GS 1 8 . 3 5 0 4 x 2 BL S -TS
-TS = Weight optimised version for silo tanker
Table 4: Designations for special designs produced to-date (to be supplemented with further designs)
-U For low design Ultra e.g.: TGX 18.400 4x2 LLS-U
-TS Weight optimised version for silo tanker, e.g.: TGS 18.400 4x2 BLS-TS
-WW World wide variant, eligible for licensing outside Europe only, e.g. TGA 40.xxx 6X6 BB-WW
-CKD Completely knocked down, for assembly in MAN factory of the recipient country, e.g.: TGS 40.xxx 6x4 BB-WW-CKD
-EL EfcientLine
2.2 Model number, vehicle identication number, vehicle number, basic vehicle number
The three-digit model number, also called model code, provides a technical identication of the MAN chassis and also identies
to which vehicle range it belongs. This number is part of the 17-digit vehicle identication number (VIN) and is located at digits 4 to 6 in
the VIN. The basic vehicle number, formulated for sales purposes, also contains the model number at digits 2 to 4.
The seven-gure vehicle number describes the technical equipment on a vehicle; it contains the model number at digits 1 to 3, followed
by a four-digit sequential number. The vehicle number is to be found in the vehicle papers and on the vehicles manufacturing plate.
The vehicle number can be quoted instead of the 17-digit vehicle identication number in the event of any technical queries regarding
conversions and bodies. Table 5 gives some examples of the model number, vehicle identication number, basic vehicle number and
vehicle number.
Table 5: Example vehicle designation, model number, vehicle identication number, basic vehicle number and vehicle number
Vehicle designation Model number
Model code
Vehicle identication number
(VIN)
Basic vehicle
number
Vehicle number
TGX 18.440 4x2 BLS
TGS 26.410 6x2-4 LL
TGX 33.540 6x4 BB
06X
21S
26X
WMA06XZZ97K001464
WMA21SZZ67M479579
WMA26XZZ67K001465
L06XKG31
L21SGF38
L26XLV12
06X0004
21S0002
26X0001
TRUCKNOLOGY
Table 6: Model numbers, tonnage class, vehicle designation and wheel formula on TGS, TGS-WW and TGX
TGS model code
Model number Tonnage Designation , xxx stands for
various engine powers
Engine Suspension
03S 18 t TGS 18.xxx 4X2 BB D20/D26 R6 BB
06S 18 t TGS 18.xxx 4X2 BL D20/D26 R6 BL
08S 18 t TGS 18.xxx 4X2 BLS-TS D20/D26 R6 BL
10S 18 t TGS 18.xxx 4X2 LL D20/D26 R6 LL
13S 18 t TGS 18.xxx 4X2 LLS-U D20/D26 R6 LL
15S 18 t TGS 18.xxx 4X2 LL-U D20/D26 R6 LL
18S 26 t TGS 26.xxx 6X2-2, 6X2-4 BL D20/D26 R6 BLL
21S 26 t TGS 26.xxx 6X2-2, 6X2-4 LL D20/D26 R6 LLL
22S 18 t TGS 18.xxx 4X4H BL D20/D26 R6 BL
24S 24/26 t TGS 24/26.xxx 6X2/2, 6X2/4 BL D20/D26 R6 BLL
26S 26/33 t TGS 26/33.xxx 6X4 BB D20/D26 R6 BBB
30S 26/33 t TGS 26/33.xxx 6X4 BL D20/D26 R6 BLL
35S 26 t TGS 26.xxx 6X4H-2, 6X4H-4 BL D20/D26 R6 BLL
37S 35 t TGS 35.xxx 8X4 BB D20/D26 R6 BBBB
39S 37/41 t TGS 37/41.xxx 8X4 BB D20/D26 R6 BBBB
41S 32/35 t TGS 32/35.xxx 8X4 BL D20/D26 R6 BBLL
42S 26 t TGS 26.xxx 6X4H/2, 6X4H/4 BL D20/D26 R6 BLL
45S 24 t TGS 24.xxx 6X2-2 LL-U D20/D26 R6 LLL
49S 32 t TGS 32.xxx 8X4 BB D20/D26 R6 BBBB
Engine Suspension
52S 18 t TGS 18.xxx 4X4 BB D20/D26 R6 BB
56S 26/33 t TGS 26/33.xxx 6X6 BB D20/D26 R6 BBB
59S 35 t TGS 35.xxx 8X6H BL D20/D26 R6 BBLL
70S 26 t TGS 26.xxx 6X6H BL D20/D26 R6 BLL
71S 28 t TGS 28.xxx 6X4H-4 BL D20/D26 R6 BLL
73S 35 t TGS 35.xxx 8X4H-6 BL D20/D26 R6 BBLL
74S 28 t TGS 28.xxx 6X2-4 BL D20/D26 R6 BLL
80S 18 t TGS 18.xxx 4X4 BL D20/D26 R6 BL
82S 26/33 t TGS 26/33.xxx 6X6 BL D20/D26 R6 BLL
90S 35 t TGS 35.xxx 8X2-4, 8X2-6 BL D20/D26 R6 BBLL
92S 35 t TGS 35.xxx 8X4-4 BL D20/D26 R6 BLLL
TRUCKNOLOGY
TGS-WW model code
Engine Suspension
03W 19 t TGS 19.xxx 4X2 BBS-WW D20/D26 R6 BB
06W 19 t TGS 19.xxx 4X2 BLS-WW D20/D26 R6 BL
18W 26 t TGS 26.xxx 6X2-2, 6X2-4 BL-WW D20/D26 R6 BLL
19W 28 t TGS 28.xxx 6X2-2 BL-WW D20/D26 R6 BLL
26W 33 t TGS 33.xxx 6X4 BB-WW D20/D26 R6 BBB
30W 26/33 t TGS 26/33.xxx 6X4 BLS-WW D20/D26 R6 BLL
39W 41 t TGS 41.xxx 8X4 BB-WW D20/D26 R6 BBBB
49W 32 t TGS 32.xxx 8X4 BB-WW D20/D26 R6 BBBB
52W 18 t TGS 18.xxx 4X4 BB-WW D20/D26 R6 BB
60W 35/41 t TGS 35/41.xxx 8X8 BB-WW D20/D26 R6 BBBB
71W 19 t TGS 19.xxx 4X2 BBS-WW-CKD D20/D26 R6 BB
72W 19 t TGS 19.xxx 4X2 BLS-WW-CKD D20/D26 R6 BL
73W 28 t TGS 28.xxx 6X2-2 BL-WW-CKD D20/D26 R6 BLL
76W 33 t TGS 33.xxx 6X4 BB-WW-CKD D20/D26 R6 BBB
77W 40 t TGS 40.xxx 6X4 BB-WW-CKD D20/D26 R6 BBB
78W 26 t TGS 26.xxx 6X4 BL-WW-CKD D20/D26 R6 BLL
79W 41 t TGS 41.xxx 8X4 BB-WW-CKD D20/D26 R6 BBBB
TRUCKNOLOGY
TGX model code
Engine Suspension
05X 18 t TGX 18.xxx 4X2 BLS D20/D26 R6 BL
06X 18 t TGX 18.xxx 4X2 BL D20/D26 R6 BL
10X 18 t TGX 18.xxx 4X2 LL D20/D26 R6 LL
13X 18 t TGX 18.xxx 4X2 LLS-U D20/D26 R6 LL
15X 18 t TGX 18.xxx 4X2 LL-U D20/D26 R6 LL
18X 26 t TGX 26.xxx 6X2-2, 6X2-4 BL D20/D26 R6 BLL
21X 26 t TGX 26.xxx 6X2-2, 6X2-4 LL D20/D26 R6 LLL
22X 18 t TGX 18.xxx 4X4H BL D20/D26 R6 BL
24X 24/26 t TGX 24/26.xxx 6X2/2, 6X2/4 BL D20/D26 R6 BLL
26X 26/33 t TGX 26/33.xxx 6X4 BB D20/D26 R6 BBB
27X 28 t TGX 28.xxx 6X4 BB D20/D26 R6 BBB
28X 28 t TGX 28.xxx 6X4 BB-CKD D20/D26 R6 BBB
30X 26/33 t TGX 26/33.xxx 6X4 BL D20/D26 R6 BLL
42X 26 t TGX 26.xxx 6X4H/2, 6X4H/4 BL D20/D26 R6 BLL
45X 24 t TGX 24.xxx 6X2-2 LL-U D20/D26 R6 LLL
78X 18 t TGX 18.xxx4X2 BLS D28 V8 BL
79X 33 t TGX 33.xxx 6X4 BL D28 V8 BLL
86X 41 t TGX 41.xxx 8X4/4 BBS D26 R6 BLBB
87X 41 t TGX 41.xxx 8X4/4 BLS D26 R6 BLLL
88X 28 t TGX 28.xxx 6X2-2 BL-CKD D20/D26 R6 BLL
89X 28 t TGX 28.xxx 6X2-2 BL D20/D26 R6 BLL
92X 35 t TGX 35.xxx 8X4-4 BL D20/D26 R6 BLLL
94X 41 t TGX 41.xxx 8X4/4 BBS D28 V8 BLBB
95X 41 t TGX 41.xxx 8X4/4 BLS D28 V8 BLLL
2.3 Use of logos
MAN logos on the chassis may not be removed or modied in any way without prior approval from MAN.
Modications to the chassis or body that do not conform with this Guide to Fitting Bodies and that have not received MAN approval ba
MAN (for address see Publisher above) must receive a new vehicle identication number (VIN) from the manufacturer responsible for
the modication (normally the vehicle conversion company).
In such cases where the chassis/vehicle has received a new VIN, the logos on the radiator grille (MAN lettering, lion emblem) and
the doors (door designation see Section 2.1.1) must be removed.
TRUCKNOLOGY
2.4 Cabs
TGS and TGX cabs are of different sizes. There are 3 different cabs each:
Table 7.1: TGS cabs up to EURO 5 exhaust emission standard

TGS cabs up to EURO 5 exhaust emission standard
Description Dimensions* Views
Name
Technical
description
Length Width High roof Side Front
M
LHD
F99L17S
RHD
F99R17S
1.880 2.240 1737
L
LHD
F99L34S
RHD
F99R34S
2.280 2.240 1737
LX
LHD
F99L39S
RHD
F99R39S
2.280 2.240 2035
*) Dimensions refer to the cab without attachments such as mudguards, front spoiler, mirrors, roof spoiler etc.
TRUCKNOLOGY
Table 7.2: TGS cabs from EURO 6 exhaust emission standard
TGS cabs from EURO 6 exhaust emission standard
Name Technical
Description
M
LHD
F99L17S
RHD
F99R17S
1.880 2.240 1737
L
LHD
F99L34S
RHD
F99R34S
2.280 2.240 1737
LX
LHD
F99L39S
RHD
F99R39S
2.280 2.240 2035
TRUCKNOLOGY
Table 7.3: TGX cabs up to EURO 5 exhaust emission standard
TGX cabs up to EURO 5 exhaust emission standard
Name Technical
Description
XL
LHD
F99L44S
RHD
F99R44S
2.280 2.440 1737
va va va VA VA
XLX
LHD
F99 L49 S
RHD
F99 R49 S
2.280 2.440 2035
va
XXL
LHD
F99L45S
RHD
F99R45S
2.280 2.440 2260
TRUCKNOLOGY
Table 7.4: TGX cabs from EURO 6 exhaust emission standard
TGX bei Abgasnorm Euro 6
Description Dimensions* View
Name Technical
Description
XL
LHD
F99L44S
RHD
F99R44S
2.280 2.440 1737
XLX
LHD
F99 L49 S
RHD
F99 R49 S
2.280 2.440 2035
XXL
LHD
F99L45S
RHD
F99R45S
2.280 2.440 2260
TRUCKNOLOGY
2.5 Engine variants
In-line six-cylinder Diesel engines (R6) of the D20/D26 Common Rail range are installed in the TGS and TGX (= 1st 3rd digits of
the engine designation). The engines are available in Euro 4 with cooled EGR and PM-Kat
plus Euro 5 with SCR technology.

A newly developed V8 Common Rail engine from the D28 family supplements the TGX range. In accordance with European
regulations the engines are tted with on board diagnosis, including a NO
x
analyser (with engine torque limitation in the event of NO
x

analyser failure). and exhaust gas aftertreatment in accordance with the following table:
Abbreviations:
EGR: Exhaust Gas Recirculation
EEV: Enhanced Environmentally friendly Vehicle
OBD: On-Board Diagnostics
PM-Kat
: Particulate Matter (particle lter)

SCR: Selective Catalytic Reduction using AdBlue as the reducing agent
TRUCKNOLOGY
Table 8: TGS/TGX engines/engine designations D20 / D26
Vehicle
designation
Emission
class
Power [kW] /
at rpm
ODB
generation
EGR Exhaust
gas after
treatment
Max. torque
[Nm] / at [rpm]
Engine
type
Engine
designation
xx.360
Euro 3
265 kW / 1.900
No OBD
EGR
None
1.800 at 1.000 - 1.400 rpm
R6
D2066LF48
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF49
xx.440 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF50
xx.480 353 kW / 1.900 2.300 at 1.050 - 1.400 rpm D2676LF31
xx.320
Euro 4
235 kW / 1.900
OBD 1 +
NO
x
control
PM-Kat
1.600 at 1.000 - 1.400 rpm D2066LF39

xx.360 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF38
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF37
xx.440 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF36
xx.480 353 kW / 1.900 2.300 at 1.050 - 1.300 rpm D2676LF05
xx.320 235 kW / 1.900
No EGR SCR
1.600 at 1.000 - 1.400 rpm D2066LF65
xx.360 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF64
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF63
xx.440 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF62
xx.480 353 kW / 1.900 2.300 at 1.050 - 1.300 rpm D2676LF20
xx.540 397 kW / 1.900 2.500 at 1.050 - 1.350 rpm D2676LF19
xx.320* 235 kW / 1.900 1.600 at 1.000 - 1.400 rpm D2066LF72
xx.360* 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF71
xx.400* 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF70
xx.440* 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF69
xx.480* 353 kW / 1.900 2.300 at 1.050 - 1.400 rpm D2676LF33
xx.540* 397 kW / 1.900 2.500 at 1.050 - 1.350 rpm D2676LF32
xx.320
Euro 5
235 kW / 1.900 1.600 at 1.000 - 1.400 rpm D2066LF28
xx.360 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF27
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF26
xx.440 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF25
xx.480 353 kW / 1.900 2.300 at 1.050 - 1.300 rpm D2676LF14
xx.540 397 kW / 1.900 2.500 at 1.050 - 1.350 rpm D2676LF13
xx.320* 235 kW / 1.900 1.600 at 1.000 - 1.400 rpm D2066LF20
xx.360* 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF19
xx.400* 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF18
xx.440* 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF17
xx.480* 353 kW / 1.900 2.300 at 1.050 - 1.400 rpm D2676LF16
xx.540* 397 kW / 1.900 2.500 at 1.050 - 1.350 rpm D2676LF15
TRUCKNOLOGY
Vehicle
designation
Emission
class
Power [kW] /
at rpm
ODB
generation
EGR

Exhaust
gas after
treatment
Max. torque
[Nm] / at [rpm]
Engine
type
Engine
designation
xx.320
Euro5
235 kW / 1.900
OBD 2
+ NO
x

control
No EGR SCR
1.600 at 1.000 - 1.400 rpm
R6
D2066LF43
xx.360 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF42
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF41
xx.440 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF40
xx.480 353 kW / 1.900 2.300 at 1.050 - 1.400 rpm D2676LF07
xx.540 397 kW / 1.900 2.500 at 1.050 - 1.350 rpm D2676LF06
xx.320* 235 kW / 1.900 1.600 at 1.000 - 1.400 rpm D2066LF47
xx.360* 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF46
xx.400* 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF45
xx.440* 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF44
xx.480* 353 kW / 1.900 2.300 at 1.050 - 1.400 rpm D2676LF09
xx.540* 397 kW / 1.900 2.500 at 1.050 - 1.350 rpm D2676LF08
xx.320 235 kW / 1.900
EGR Oxi-Kat
1.600 at 1.000 - 1.400 rpm D2066LF53**
xx.360 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF52**
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF51**
xx.440 324 kW / 1.900 2.100 at 950 - 1.400 rpm D2676LF22**
xx.480 353 kW / 1.900 2.300 at 950 - 1.400 rpm D2676LF21**
xx.320
EEV
235 kW / 1.900
No EGR SCR
1.600 at 1.000 - 1.400 rpm D2066LF60
xx.360 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF59
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF58
xx.440 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF57
xx.480 353 kW / 1.900 2.300 at 1.050 - 1.400 rpm D2676LF18
xx.540 397 kW / 1.900 2.500 at 1.050 - 1.350 rpm D2676LF17
xx.320
Euro 6
235 kW / 1800
OBD 2
+ NO
x

control
EGR SCR
1600 at 930 - 1400 rpm
R6
D2066LF68
xx.360 265 kW / 1800 1800 at 930 - 1400 rpm D2066LF67
xx.400 294 kW / 1800 1900 at 930 - 1400 rpm D2066LF61
xx.440 324 kW / 1800 2100 at 930 - 1400 rpm D2676LF26
xx.480 353 kW / 1800 2300 at 930 - 1400 rpm D2676LF25
* = In case of NO
X
system failure, engines tted with OBD 1b or OBD 2 are without torque reduction (TR). Only applies to engines for re services,
rescue services and military vehicles in accordance with Annex I.6558 of Directive 2005/55/EC, version 2006/81/EC
** = Engines only for UK and Ireland
Tabelle 9: TGX engines/engine designations D28 V8
Vehicle
designation
Emission
class
Power [kW] /
at rpm
ODB
generation
EGR

Exhaust
gas after
treatment
Max. torque
[Nm] / at [rpm]
Engine
type
Engine
designation
xx.680 Euro 5 500 kW / 1.800 OBD 1
+ NOx
control
No EGR SCR
3.000 at 1.100 - 1.500 rpm
V8
D2868LF02
xx.680 500 kW / 1.900 2.700 at 1.000 - 1.700 rpm D2868LF03
xx.680* 500 kW / 1.900 OBD 2
+ NOx
control
2.700 at 1.000 - 1.700 rpm D2868LF04
xx.680 500 kW / 1.900 2.700 at 1.000 - 1.700 rpm D2868LF06
xx.680* 500 kW / 1.900 2.700 at 1.000 - 1.700 rpm D2868LF07
xx.680 EEV 500 kW / 1.800 3.000 at 1.100 - 1.500 rpm D2868LF05
* = In case of NO
X
TRUCKNOLOGY
Tabelle 10: TGS-WW engines/engine designations D20 / D26
Vehicle
designation
Emission
class
Power [kW] /
at rpm
ODB
generation
EGR Exhaust
gas after
treatment
Max. torque
[Nm] / at [rpm]
Engine
type
Engine
designation
xx.360
Euro 3
265 kW / 1.900
No OBD
EGR
None
1.800 at 1.000 - 1.400 rpm
R6
D2066LF48
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF49
xx.440 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF50
xx.480 353 kW / 1.900 2.300 at 1.000 - 1.400 rpm D2676LF02
xx.480 353 kW / 1.900 2.300 at 1.000 - 1.400 rpm D2676LF31
xx.320
Euro 4
235 kW / 1.900
OBD 1
PM-Kat
1.600 at 1.000 - 1.400 rpm D2066LF35

xx.360 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF33
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF32
xx.440 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF31
xx.480 353 kW / 1.900 2.300 at 1.050 - 1.300 rpm D2676LF01
xx.320 235 kW / 1.900
OBD 1
+ NO
X

control
1.600 at 1.000 - 1.400 rpm D2066LF39
xx.360 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF38
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF37
xx.440 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF36
xx.480 353 kW / 1.900 2.300 at 1.050 - 1.300 rpm D2676LF05
xx.320 235 kW / 1.900
No EGR SCR
1.600 at 1.000 - 1.400 rpm D2066LF65
xx.360 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF64
xx.400 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF63
xx.440 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF62
xx.480 353 kW / 1.900 2.300 at 1.050 - 1.400 rpm D2676LF20
xx.540 397 kW / 1.900 2.500 at 1.050 - 1.350 rpm D2676LF19
xx.320* 235 kW / 1.900 1.600 at 1.000 - 1.400 rpm D2066LF72
xx.360* 265 kW / 1.900 1.800 at 1.000 - 1.400 rpm D2066LF71
xx.400* 294 kW / 1.900 1.900 at 1.000 - 1.400 rpm D2066LF70
xx.440* 324 kW / 1.900 2.100 at 1.000 - 1.400 rpm D2066LF69
xx.480* 353 kW / 1.900 2.300 at 1.050 - 1.400 rpm D2676LF33
xx.540* 397 kW / 1.900 2.500 at 1.050 - 1.350 rpm D2676LF32
* = In case of NO
X
Tabelle 11: Engine for 27X and 28X engine designations D26 (not EC and without torque limitation) in models 27X and 28X
Vehicle
designation
Emission
class
Power [kW] /
at rpm
ODB
generation
EGR Exhaust gas
after treat-
ment
Max. torque
[Nm] / at [rpm]
Engine
type
Engine
designation
xx.440 Conama P6 324 kW / 1.900 No OBD EGR Oxi-Kat 2.100 at 1.000 - 1.400 rpm
R6
D2676LF10
xx.480*
Conama P7
353 kW / 1.900
ODB 2 (Brasil) No EGR SCR
2.400 at 1.000 - 1.400 rpm D2676LF23
xx.400* 294 kW / 1.900 2.000 at 1.000 - 1.400 rpm D2676LF24
xx.440* 324 kW / 1.900 2.200 at 1.000 - 1.400 rpm D2676LF28
* = OBD 2 engines (Brasil) without torque reduction (DMR) in the case of No
X
system failure.
G G
TRUCKNOLOGY
3. General
National and international regulations take priority over technically permissible dimensions and weights if they limit the technically
permissible dimensions and weights. The following data can be obtained from the quotation documents and documents contained in
MANTED
at www.manted.de:
Dimensions
Weights
Centre of gravity position for payload and body (minimum and maximum position for body)
for the production standard chassis / tractor unit. The data contained in these documents may vary depending on what technical
features the vehicle is actually tted with upon delivery. The critical factor is the vehicles actual conguration and condition at the time
delivery. To achieve optimum payload carrying capability the chassis must be weighed before work starts on the body.
Calculations can then be made to determine the best centre of gravity position for payload and body as well as the optimum body
length. As a result of component tolerances the weight of the standard chassis is allowed to vary by 5%, in accordance with
DIN 70020. Any deviations from the standard equipment level will have a greater or lesser effect on dimensions and weights.
Changes in equipment may result in deviations in the dimensions and weights, particularly if different tyres are tted that then also lead
to a change in the permissible loads.
In each individual case when a body is tted care needs to be taken to ensure the following
Under no circumstances may the permissible axle weights be exceeded
A sufcient minimum front axle load is achieved
The position of the centre of gravity and loading must not be one-sided
The permissible overhang (vehicle overhang) is not exceeded.
3.1 Axle overload, one-sided loading
Fig. 1: Overloading the front axle ESC-452
Fig. 2: Difference in wheel load ESC-126
TRUCKNOLOGY
Formula 1: Difference in wheel load
G 0,05 G
tat
The body must be designed such that one-sided wheel loads do not occur. Following checks, a maximum wheel load difference of 5%
is permitted (where 100% represents the actual axle load and not the permissible axle load).
Example:
Actual axle load G
tat
= 11.000 kg
Therefore, the permissible wheel load difference is:
G = 0,05 G
tat
= 0,05 11.000 kg
G = 550 kg
This means for example that the wheel load on one side is 5,225 kg and 5,775 kg on the other.
The calculated maximum wheel load provides no information on the permissible individual wheel load for the tyres tted.
Information on this can be found in the technical manuals supplied by the tyre manufacturers.
3.2 Minimum front axle load
In order to maintain steerability, the stipulated minimum front axle load must be ensured under all vehicle load conditions, see table 12.
Fig. 3: Minimum front axle loading ESC-451
TRUCKNOLOGY
Table 12: Minimum front axle loading for any load condition as a % of the respective actual vehicle weight
Minimum front axle loading for any load condition as a % of the respective actual vehicle weight
GVW = Gross vehicle weight
SDAH = Rigid drawbar trailer
ZAA = ZAA = Centre-axle trailer
Number of axles Wheel formula
Without SDAH
/ZAA
With SDAH /ZAA
GG trailer 18 t
Tridem SDAH /ZAA
GG trailer > 18 t
Other rear load
e.g. crane, taillift
Two-axle vehicle
4x2, 4x4H
4x4
25% 25% 35% 30%
More than 2 axles
6x2/2, 6x2/4
6x2-2, 6x2-4
6x4, 6x4-4
6x4H/2, 6x4H/4
6x4H-2, 6x4H-4
6x6, 6x6H
8x2-4, 8x2-6 8x4,
8x4/4, 8x4-4
8x4H-6, 8x6,
8x6H, 8x8
20% 25%* 30%* 25%*
If more than one front axle is tted the % value is the total of the front axle loads.
* = Three axle vehicles with lifting leading or trailing axles must be treated as having two axles when the lifting axles are raised.
In this condition the higher minimum front axle load for two axle vehicles applies.
** = -2% for steered leading/trailing axles, only if the vehicles are loaded/unloaded with payloads.
With combined rear loads like rigid drawbar trailers with loading crane for example, the higher minimum front axle load is valid.
These values are inclusive of any additional rear loads such as:
nose weights exerted by a centre-axle trailer
loading cranes
tail lifts
transportable fork lift trucks.
3.3 Wheels, rolling circumference
Different tyre sizes on the front and rear axle(s) can only be tted to all-wheel-drive vehicles if the difference in rolling circumference of
the tyres used does not exceed 2% or 1.5% if the MAN HydroDrive
system is installed.
The basis for calculation is always the circumference of the smaller tyre.
Every change of tyre type requires approval from the manufacturer. Enquiries can be made by completing the form Request for
certication, available to download from www.manted.de or via the online certication form. Any associated parameterisation will
be carried out at the same time as certication.
The notes in Chapter 5 Body relating to anti-skid chains, load rating and clearance must be observed.
3.4 Permissible overhang
The permissible overhang length is dened as the distance between the theoretical rear axle centreline (resulting from the theoretical
wheelbase) and the end of the vehicle (including the bodywork). For denition see the following the following paragraph 3.5.
The following maximum values are permitted, expressed as a percentage of the theoretical wheelbase
- Two-axle vehicles 65%
- all other vehicles 70%.
If the vehicle is not equipped to tow trailers the above values may be exceeded by 5%.
The basic requirement is that the minimum front axle loads given in table 12 (par. 3.2.) must be observed for every operating condition.
G
zul1
u
t
G
zul2
l
12
= l
t

G
zul1
u
t
G
zul2
G
zul3
l
12
l
t
l
23
TRUCKNOLOGY
Theoretical rear
axle centreline
Theoretical rear
axle centreline
G
permissible1
G
permissible1
G
permissible2
G
permissible2
G
permissible3
3.5 Theoretical wheelbase, overhang, theoretical axle centreline
The theoretical wheelbase is an aid for calculating the position of the centre of gravity and the axle loads.
The denition is given in the following gures.
Fig. 4: Theoretical wheelbase and overhang two-axle vehicle ESC-446
Formula 2: Theoretical wheelbase for a two-axle vehicle
l
t
= l
12
Formula 3: Permissible overhang for a two-axle vehicle
U
t
0,65 l
t
Fig. 5: Theoretical wheelbase and overhang for a three-axle vehicle with two rear axles and identical rear axle loads ESC-447
G
zul1
u
t
G
zul2
G
zul3
l
12
l
t
l
23
TRUCKNOLOGY
Theoretical rear
axle centreline
G
permissible1
G
permissible2
G
permissible3
Formula 4: Theoretical wheelbase for a three-axle vehicle with two rear axles and identical rear axle loads
l
t
= l
12
+ 0,5 l
23
Formula 5: Permissible overhang for a three-axle vehicle with two rear axles and identical rear axle loads
U
t
0,70 l
t
Fig. 6: Theoretical wheelbase and overhang for a three-axle vehicle with two rear axles and different rear axle
loads (e.g. in the MAN vehicle range all 6x2s) ESC-448

Formula 6: Theoretical wheelbase for a three-axle vehicle with two rear axles and different rear axle loads
G
permissible3
l
23
l
t
= l
12
+
G
permissible2
+ G
permissible3
Formula 7: Permissible overhang length three-axle vehicle with two rear axles and unequal rear axle loads
U
t
0,70 l
t
TRUCKNOLOGY
Theoretical rear
axle centreline
Theoretical front
axle centreline
G
permissible1
l
12
l
23
l
t
U
t
l
34
G
permissible2
G
permissible3
G
permissible4
Fig. 7: Theoretical wheelbase and overhang for a four-axle vehicle with two front and two rear axles
(any axle load distribution) ESC-450

Formula 8: Theoretical wheelbase for a four-axle vehicle with two front and two rear axles (any axle load distribution)
G
permissible1
l
12
G
permissible4
l
34
l
t
= l
23
+ +
G
permissible1
+ G
permissible2
G
permissible3
+ G
permissible4
Formula 9: Permissible overhang length for a four-axle vehicle with two front and two rear axles
U
t
0,70 l
t
3.6 Calculating the axle load and weighing procedure
It is essential that an axle load calculation be completed in order to ensure correct design of the body.
The weights given in the sales documents only apply to production standard vehicles. Weight differences can be caused by optional
equipment or manufacturing tolerances. Manufacturing inaccuracies (within tolerances) may occur.
Achieving optimum compatibility between bodywork and truck is only possible if the vehicle is weighed before any work on the body is
commenced. The weights thus obtained are then taken as a basis for an axle load calculation.
The vehicle must be weighed subject to following conditions:
Without the driver
With a fully lled AdBlue
tank and fully lled fuel tank

With the handbrake released and the vehicle secured with chocks
If tted with air suspension, raise the vehicle to normal driving position
Liftable axle(s) must be raised to the normal driving position (as in loaded condition)
Do not actuate any moving-off aid.
TRUCKNOLOGY
Observe the following sequence when weighing a vehicle (leading or trailing axle relates to the rear axle):
Two-axle vehicles
1
st
axle
2
nd
axle
whole vehicle as a check
Three-axle vehicles with two rear axles
1
st
axle
2
nd
together with 3
rd
axle
Four axle vehicle with two front and two rear axles
1
st
together with 2
nd
axle
3
rd
together with 4
th
axle
Four-axle vehicle with one front and three rear axles
1
st
axle
2
nd
together with 3
rd
and 4
th
axles
whole vehicle as a check.
3.7 Checking and adjustment procedures before and after body has been tted

On the TGS/TGX do not check or adjust:
ALB settings: No adjustments necessary once bodywork has been tted
Tachograph MTCO as this has already been calibrated at the factory
Digital tachograph DTCO as this has already been calibrated at the factory.
According to EU Directives however, a person authorised to carry out tests must enter the registration number (normally this is not yet
assigned when the vehicle leaves the MAN factory).

When installing a central lubrication system:
Do not connect the lubrication system to the low-maintenance brake camshafts on drive axles tted with drum brakes.
Drive axles tted with drum brakes are installed on all-wheel drive vehicles and on vehicles of medium build height (planetary axles).
Low-maintenance brake camshafts can be recognised from their protective tube, see Fig. 8.
Lubrication may only be applied every 4 years using special high-temperature grease in accordance with MAN Standard 284.
TRUCKNOLOGY
with
protective tube
without
protective tube
Fig. 8: Protective tube of the low-maintenance brake camshaft ESC-481
Checking and adjustment procedures that must be completed by the bodybuilder before/once the body has been tted:
Before the body is tted, the roof spoiler supplied by MAN and mounted on the chassis frame must be tted onto the cab roof.
Basic beam alignment of the headlamps, see also Section 6.6 in this booklet for details
Check battery charge status according to the charging schedule, sign battery charging log.
See also the Chapter Electrics, electronics, wiring
Check rear underride protection for compliance with statutory regulations.
Check sideguards for compliance with statutory regulations (for dimensions see the Chapter Modifying the chassis)
and adjust as necessary.
A digital tachograph DTCO must be calibrated after the body has been tted. Furtermore, all information e.g. vehicle
registration number and the country of registration must be added. Since April 2011 the vehicle registration number and
the country of registration must be entered into new tachographs using the company card, even if the calibration data is not
changed. This must be performed by an authorised person.
TRUCKNOLOGY
3.8 Notes on MAN Hydrodrive
MAN Hydrodrive
is a hydrostatic front axle drive that employs wheel hub motors. The system is selectable and operates in the speed
range between 0 and 28 km/h. Vehicles tted with Hydrodrive
are legally regarded as off-road vehicles as dened by 70/156 EEC

(as last amended by 2005/64/EU and 2005/66/EG).
The Hydrodrive
hydraulic circuit is solely approved for the regulated drive of the front axle and may not be used to supply other
hydraulic systems. Modications to the Hydrodrive
hydraulic system (including relocating pipework) may only be carried out by

specically authorised companies.
In the case of semi-trailer tippers and other bodies where there is a risk of the cargo falling into the area around the oil cooler an oil
cooler cover must be tted. This is available tted ex-works or as a retrot solution under the name Protective cover for oil cooler/fan
for HydroDrive
. (Installation no. 81.36000.8134).

4. Modifying the chassis
To provide customers with the products they want, additional components sometimes need to be installed, attached or modied.
For uniformity of design and ease of maintenance, we recommend that original MAN components be used as long as these comply
with the vehicles structural design. To keep maintenance work to a minimum, we recommend the use of components that have the
same maintenance intervals as the MAN chassis. Modications to safety-critical components of wheel/axle guides, steering and brakes
are not allowed. Existing anti-roll bars may neither be removed nor modied.
Installation and/or modication of components frequently requires intervention in the control units CAN architecture (e.g. when
extending the EBS electronic braking system). The necessary modications and/or expansion of the vehicle programming are
described under the corresponding topic in these guidelines.
Such modications may only be undertaken with assistance from the electronics experts at MAN service centres and the programming
must be approved by MAN (for address see Publisher above). Retrotted systems may, under certain circumstances, not be assimila-
ted into the vehicles on-board Trucknology
systems Time maintenance system of Flexible maintenance system.

For this reason it is not possible to achieve the same degree of maintenance convenience as is possible with original equipment.
4.1 Frame material
When carrying out modications to the chassis longitudinal and cross-members only use of the original frame material S500MC
(QStE 500TM) is approved.
Exception: For prole 33 and 42, the frame is made of S420MC = QStE420TM.
For prole 43, the frame is made of LNE500 to Brasilian standard NBR 6656:2008
Table 13: Steel for TGS/TGX frame
Material
number
Previous
material
designation
Previous
standard
0,2
N/mm
2
B
N/mm
2
New material
designation
New
standard
Prole codes as
per table 14
1.0980 QStE420TM SEW 092 420 480-620 S420MC DIN EN 10149-2 33
1.0984 QStE500TM SEW 092 500 550-700 S500MC DIN EN 10149-2 31 32 34
500 560-700 LNE500 NBR 6656:2008 43
For subframe longitudinal and cross-members only steels with a yield point of
0,2
350 N/mm
2
may be used.
For additional details on subframes see the Subframe Chapter 5.3.3.
Depending on the model, the following longitudinal frame members are used.
B
o

B
u

e
x

h

H

R

t
e
y

TRUCKNOLOGY
Surface centre of gravity S
Fig. 9: Prole data for longitudinal frame members ESC-112
Table 14: Prole data for longitudinal frame members (Proles in bold are used for TGS and TGX ranges)
No H
mm
h
mm
B
o
mm
B
u
mm
t
mm
R
mm
G
kg/m
0,2
N/mm
2
B
N/mm
2
A
Mm
2
e
x
mm
e
y
mm
l
x
cm
4
W
x1
cm
3
W
x2
cm
3
l
y
cm
4
W
y1
cm
3
W
y2
cm
3
31 270 254 85 85 8 10 26 500 550..700 3296 20 135 3255 241 241 201 101 31
32 270 251 85 85 9,5 10 30 500 550..700 3879 21 135 3779 280 280 232 110 36
33 334 314 85 85 10 10 37 420 480..620 4711 19 167 6691 401 401 257 135 39
34 270 256 85 85 6,8 10 22 500 550..700 2821 19 135 2816 209 209 174 92 26
43
1)
270 254 85 85 8 10 26 500 560..700 3296 20 135 3255 241 241 201 201 31
45 270 251 85 85 9,5 10 30 500 560..700 3879 21 135 3779 280 280 232 110 36
1) LNE500 in accordance with Brasilian Standard NBR 6656:2008, for TGX in Latin America (As of 03 2010:CKD types 28X.88X).
Table 15 gives the standard model-related allocation of longitudinal frame members valid on the date of publication of this guide.
No guarantee is given or implied as to the currentness or completeness of this data.
Up-to-date and binding instructions on the longitudinal frame member prole to be used can be found in:
the chassis drawing
the technical data sheet
which can be found for the corresponding vehicle at www.manted.de under Chassis.
TRUCKNOLOGY
Table 15: Model-related allocation of longitudinal frame member proles
Tonnage Type Vehicle Wheelbase Prole code
TGS TGX
18 t
03S TGS 18.xxx
4x2
BB

31
05X TGX 18.xxx
BLS-EL
BLS
06S 06X TGS/TGX 18.xxx
BL
08S TGS 18.xxx BLS-TS 34
10S 10X
TGS/TGX 18.xxx
LL
31
LLS
13S 13X LLS-U 31, 42
15S 15X LL-U
31
22S 22X 4x4 H
BL
BLS
52S
TGS 18.xxx 4x4
BBS
BB
52W BB-WW
78X TGX 18.xxx 4x2 BLS
80S
TGS 18.xxx 4x4
BL
80S BLS
24 t
24S 24X TGS/TGX 24.xxx 6x2/2 BLS 31
45S 45X LL-U 31

TRUCKNOLOGY
TGS TGX
26 t
18S 18X TGS/TGX 26.xxx 6x2-2 BLS
31
BL
18W TGS 26.xxx BL-WW
BLS-WW
21S 21X TGS/TGX 26.xxx LL
LLS
24S TGS 26.xxx 6x2/4 BL
24X TGS/TGX 26.xxx 6x2/2 BLS
TGX 26.xxx 6x2/4
26S 26X TGS/TGX 26.xxx 6x4 BBS
BB 3900 mm
> 3900 mm 32
30S 30X BL
31
BLS
30W TGS 26.xxx BLS-WW
35S
TGS/TGX 26.xxx
6x4 H-2
BL
BLS
42S
42X
6x4 H/2 BLS
6x4 H/4
BLS
TGS 26.xxx BL
70S TGS/TGX 26.xxx 6x6 H
BL
BLS
78W
TGS 26.xxx
6x4
BL-WW-CKD
BLS-WW-CKD
82S
6x6
BL
BLS
56S
BB
3900 mm
> 3900 mm 32
BBS 31
TRUCKNOLOGY
TGS TGX
28t
19W
TGS 28.xxx
6x2-2
BL-WW

31
BLS-WW
28X TGX 28.xxx 6x4 BBS-CKD 43, 45
71S
TGS 28.xxx
6x4 H-4 BL
31 73W 6x2-2
BLS-WW-CKD
BL-WW-CKD
74S 6x2-4 BL
88X TGX 28.xxx
6x2-2
BLS-CKD 45
89S
TGS 28.xxx
BL
31
BLS
84S 6x4-4 BL
89X TGX 28.xxx 6x2-2
BLS
33t
6x4
BBS
31
BB 3900 mm
> 3900 mm 32
26W TGS 33.xxx
BB-WW 3900 mm 31
3900 mm 32
BBS-WW

31
BL
BLS
30W
TGS 33.xxx
BLS-WW
47S 6x6 H
BB
BBS
56W 6x6
BBS-WW
BB-WW
76W
6x4
BBS-WW-CKD
BB-WW-CKD 3900 mm
3900 mm 32
79X TGX 33
BLS

31 BL
82S
TGS 33.xxx 6x6
BL 4200 mm
4200 mm 32
BLS 31
56S
BB 3900 mm 31
> 3900 mm 32
BBS 31
TRUCKNOLOGY
TGS TGX
35 t
37S
TGS 35.xxx
8x4
BB
31
41S BL
59S 8x6 BL
60W 8x8 BB-WW
73S 8x4 H-6 BL
90S 8x2-4
BL
92S 92X TGS/TGX 35.xxx 8x4-4
93S
TGS 35.xxx 8x6 BB
96S
37 t 39S TGS 37.xxx 8x4 BB 31
40 t
34W
TGS 40.xxx
6x4
BB-WW
32
34W BBS-WW
58S
6x6
BBS
58S BB
58W BB-WW
58W BBS-WW
77W 6x4 BB-WW-CKD
41 t
39S
TGS 41.xxx
8x4
BB

32
39W BB-WW
60W 8x8 BB-WW
79W 8x4 BB-WW-CKD

86X TGX 41.xxx 8x4/4 BBS
33
87X 8x4/4 BLS
93S TGS 41.xxx 8x6 BB 32

94X
TGX 41.xxx
8x4/4 BBS
33
95X 8x4/4 BLS
96S TGS 41.xxx 8x8 BB 32
4.1.1 Subframe material
For reasons of strength, the materials S235JR (St37-2) and S260NC (QStE260N) are only suitable for use to a limited degree.
They are therefore only permitted for subframe longitudinal and cross members that are subject only to line loads from the body.
Should point loads arise or if auxiliary equipment is to be tted that exerts localised forces, e.g. tail-lifts, cranes and cable winches,
then steels with a yield point of
0,2
> 350 N/mm must always be used.
TRUCKNOLOGY
Surface and corrosion protection affects the service life and appearance of the product. In general, the quality of the coatings on body
components should be equal to that of the chassis.
In order to full this requirement, the MAN Works Standard M 3297 Corrosion protection and coating systems for non-MAN
bodies is binding for bodies that are ordered by MAN. If the customer commissions the body, this standard becomes a
recommendation only. Should the standard not be observed, MAN provides no guarantee for any consequences.
MAN-works standards may be sourced via www.normen.man-nutzfahrzeuge.de, registration required. For corrosion protection of
the body see chapter 5.2.
Series production MAN chassis are coated with environmentally friendly, water-based 2-component chassis top-coat paints at approx.
80C. To guarantee uniform coating, the following coating structure is required for all metal component assemblies on the body and
subframe:
Bare metal or blasted component surface (SA 2.5)
Primer coat: 2-component epoxy primer, permitted in accordance with MAN standard M 3162-C if possible,
cathodic dip painting to MAN works standard M 3078-2,
with zinc phosphate pre-treatment
Top coat: 2-component top-coat paint to MAN works standard M 3094, preferably water-based; if there are no
facilities for this, then solvent-based paint is also permitted. (www.normen.man-nutzfahrzeuge.de, registration required).
See the relevant paint manufacturers data sheets for information on tolerances for drying and curing times and temperatures. When
selecting and combining materials the compatibility of the different metals (e.g. aluminium and steel) must be taken into consideration as
must the effects of the electrochemical series (cause of contact corrosion).
After all work on the chassis has been completed:
Remove any drilling swarf
Remove burrs from the edges
Apply wax preservative to any cavities
Mechanical connections (e.g. bolts, nuts, washers, pins) that have not been painted over must be given optimum corrosion protection.
To prevent the occurrence of salt corrosion whilst the vehicle is stationary during the body-building phase, all chassis must be washed
with clean water to remove any salt residues as soon as they arrive at the body manufacturers premises.
4.3 Drill holes, riveted joints and screw connections on the frame
If possible, use the holes already drilled in the frame. No drilling should be carried out in the anges of the longitudinal frame member
proles, i.e. in the upper and lower anges (see Fig. 10). The only exception to this is at the rear end of the frame, outside the area of all
the parts tted to the frame that have a load-bearing function for the rearmost axle (see Fig. 11).
This also applies to the subframe.
d

b b
b b
b

b

a

a

c
TRUCKNOLOGY
a 40
b 50
c 25
TGS/TGX: d 16
Fig. 10: Frame drill holes in the upper and lower ange ESC-155 Fig. 11: Drill holes at frame end ESC-032
It is allowable to make drillings in the frame along its total useable length. However, the permissible distances between holes must be
observed (see Fig. 12). After drilling, rub down all holes and remove any burrs.
Fig. 12: Distances between drill holes ESC-021
TRUCKNOLOGY
Several frame components and add-on components (e.g. corner plates with cross member, shear plates, platform corner pieces) are
riveted to the frame during production. If modications to these components need to be carried out afterwards, screw connections
with a minimum strength class of 10.9 and mechanical locking device are permitted. MAN recommends Ripp self-locking bolts/nuts in
accordance with MAN standard M7.012.04 (may be sourced via www.normen.man-nutzfahrzeuge.de.
The manufacturers stipulated tightening torque must be observed. If double nip countersunk bolts are reinstalled then new bolts/nuts
must be used on the tightening side.
The tightening side can be recognised by slight marks on the bolts nips or nut ange (see Fig. 13).
Fig. 13: Marks on the bolts nips on the tightening side ESC-216
Alternatively, it is possible to use high-strength rivets (e.g. Huck
-BOM, blind fasteners) manufacturers installation instructions

must be followed. The riveted joint must be at least equivalent to the screw connection in terms of design and strength.
In principle it is also possible to use ange bolts. MAN draws your attention to the fact that such ange bolts place high requirements on
installation accuracy. This applies particularly when the grip length is short.
TRUCKNOLOGY
Plastic tube
4.4 Modifying the frame
4.4.1 Welding the frame
As a rule, no welding work is to be carried out on the frame and axle mountings other than that described in these guidelines or in
the MAN repair instructions. Welding work on components and assemblies that are subject to design approval (e.g. coupling devices,
underride protection) may only be carried out by the design approval holder. Welding work on these components will lead to the with-
drawal of the design approval and may pose serious trafc safety risks! Welders must have specialist knowledge in chassis welding.
The workshop must therefore employ suitably trained and qualied personnel to carry out the required welding work (e.g. in Germany,
according to the DVS leaets 2510 2512 Carrying out repair welding work on commercial vehicles, and DVS leaet 2518 Weld
criteria for use of ne grain steels in commercial vehicle manufacture/repair , available from the DVS publishing house).
The frames of MAN commercial vehicles are made from high-strength ne-grain steels. Welding work on the frame is only permitted
using the respective original frame material; see Chapter 4.1. The ne-grain steels used during manufacture are well suited for welding.
Performed by a qualied welder, the MAG (metal-active gas) and MMA (manual metal arc) welding methods ensure high quality, long
lasting welded joints.
Welding materials:
A suitable welding ller material must be chosen which has at least the same yield point and tensile strength of the material that is to be
welded.
It is important to prepare the area of the weld thoroughly before welding so that a high-quality joint can be achieved.
Heat-sensitive parts must be protected or removed. The areas where the part to be welded joins the vehicle and the earth terminal on
the welding equipment must be bare; therefore any paint, corrosion, oil, grease, dirt, etc., must be removed.
Only direct current welding may be employed; note the polarity of the electrodes.
Pipes/wires (air, electric) in the vicinity of the weld must be protected against heat. It is better to remove them completely.
Fig. 14: Protecting heat-sensitive parts ESC-156
Welding should not be attempted if the ambient temperature falls below +5C.
No undercuts are to be made whilst carrying out welding work (see llet welds, Fig. 15). Cracks in the weld seam are not permitted.
Joint seams on the longitudinal members are to be made as V or X seams in several passes. Vertical welds should be carried out from
bottom to top (see Fig. 17).
TRUCKNOLOGY
at least 2 passes
Root pass
No undercuts
Direction of welding
Fig. 15: Undercuts ESC-150 Fig. 16: Welding at X and Y seam ESC-003
Fig. 17: Vertical welds on the frame ESC-090
To prevent damage to electronic assemblies (e.g. alternator, radio, FFR, EBS, EDC, ECAS), adhere to the following procedure:
Disconnect the positive and negative leads at the battery; join the loose ends of the cables together (- with +)
Turn on the battery master switch (mechanical switch) or bypass the electric battery master switch on the solenoid
(disconnect cables and join together)
Attach the earth clip of the welding equipment directly to the area to be welded, ensuring there is good conductivity
(see above)
If two parts are to be welded together, connect them together rst, ensuring good conductivity (e.g. connect both
parts to the earth clip)
It is not necessary to disconnect electronic components and assemblies if the procedure detailed above is followed exactly.
TRUCKNOLOGY
Frame extension
Frame extension
4.4.2 Modifying the frame overhang
If the rear overhang is modied, the centre of gravity of the payload and the body shifts and, as a result, the axle loads change.
Only an axle load calculation can show whether this is within the permissible range. Such a calculation is therefore essential and must
be carried out before beginning the work. The frame overhang may only be extended using the same material as was used for the frame
during manufacture, see Chapter 4.1.
Extending the frame using several prole sections is not permissible.
Fig. 18: Extending the frame overhang ESC-493
CAN wiring harnesses may never be cut and lengthened.
Pre-prepared wiring harnesses are available from MAN for rear lights, auxiliary rear lights, trailer sockets, side marker lamps and
ABS cables. Detailed procedures are given the booklet TG Interfaces.
If it is intended to extend vehicles with short overhangs, the existing cross member between the rear spring hangers must be left
in place.
An additional frame cross member must be tted if the distance between the cross members is more than 1,500 mm (see Fig. 19).
A tolerance of +100 mm is permitted. There must always be an end cross member tted.

TRUCKNOLOGY
Fig. 19: Max. distance between frame cross members ESC-092
If a frame overhang is shortened as far as the axle guide or suspension (e.g. rear spring hanger, stabiliser bracket) the cross members
in this area (normally tubular cross-members) must either remain in place or be replaced with suitable original MAN end cross members
(see Fig. 20).
Fig. 20: Frame end of a tractor unit ESC-503
4.4.3 Modications to the wheelbase
Every change of wheelbase requires approval from the manufacturer. Enquiries can be made by completing the form A1.3 Request of
conrmations, available to download from www.manted.de or via the online certication form. The associated parameterisation of the
wheelbase and if changed the frame overhang, will be carried out at the same time as certication.
Technical design specications applicable to steering (in particular 70/311 EEC, last amended by 2004/09/24) mean that, depending
upon the number and type of steered axles, wheelbase, tyres axle loads and permissible gross weight, chassis of the TGS/TGX range
are tted with different steering wheels (diameter), steering gear (range of ratios) and steering oil piping (cooling coils).
Therefore, when considering wheelbase extensions the MAN (for address see Publisher above)
should always be rst consulted as to whether the planned change to the wheelbase will require other steering component
modications.
Parameterisation of the wheelbase modication (see next paragraph) is only possible if the correct components have been installed.
MAN shall not be liable for errors, made as a result of late consultations, that lead to increased cost. In addition, before commencing any
work, an application must be made to the MAN repair shop for a conversion data le (vehicle parameterisation) quoting the new
wheelbase. Parameterisation is carried out using the MAN-cats
diagnosis system.
Modications to the wheelbase can be made by:
Moving the entire rear axle assembly
Disconnecting the longitudinal frame members and inserting or removing a section of frame.
TRUCKNOLOGY
Provided modications are carried out in accordance with all of the following points, wheelbase modications will have been carried out
properly and approval will not be necessary.
The new wheelbase must remain between the minimum and maximum standard wheelbase for the same model according to model
code (see Chapter 2.2, Table 6). (= model limit) . ANY shortening or extension of wheelbases that exceed the model limit may only be
carried out by MAN or their qualied conversion suppliers. The maximum distance between the cross members
following a wheelbase modication is 1,500 mm. A tolerance of +100 mm is permitted. Any modications to the driveshaft section of
the driveline must be carried out according to the guidelines contained in this Guide to Fitting Bodies, see Chapter 4.6.3.1 and the
instructions provided by the driveshaft manufacturer. If the new wheelbase is the same as a series wheelbase on a production model,
then the arrangement of the driveshaft and cross members must be the same as that for a series wheelbase vehicle. Guidelines on
moving air pipes and electric cables are contained in Chapter 6, Electrics, electronics and wiring). CAN wiring harnesses may not be
cut, therefore when shortening the wheelbase, the wiring harness should simply be routed over a longer distance.
Do not form rings or loops.
During wheelbase extensions all rear axle related control units and sensors must be moved with the axle. Appropriate wiring harness
adapters are therefore available for all rear axle related control units and sensors. System, method and item numbers are described
in detail in the booklet Interfaces TG. Axle guide components and suspension (e.g. spring hangers, trailing arm brackets) may not be
located in the area ahead of and within the bends in the frame, a minimum clearance of 100 mm to the 2nd frame break must be
adhered to (see Fig. 21).
Fig. 21: Forbidden zone for rear axle locating parts ESC-500
On types with hydraulic forced steering of the trailing axle ZF-Servocom
RAS (e.g. all 6x2-4), depending upon the extent of the

wheelbase modication, steering arms with different steering angles must be installed on the 1
st
and 2
nd
axles, according to table 16.
Table 16: Steering arms for 6x2-4 with ZF-Servocom
RAS trailing axle steering

Wheelbase [mm]
1
st
2
nd
axle
Steering armitem no. max. steering angle steering arm
3.900 4.200 81.46705.0508 19
> 4.200 4.800 81.46705.0004 16,5
> 4.800 5.500 81.46705.0509 14,5
> 5.500 81.46705.0510 13,5

On types tted with ZF-Servocom
RAS-EC electronic/hydraulic leading axle steering system (all 6x2/4 and 8x4/4 vehicles) extending
the wheelbase is not possible however shortening it is. Modications to the steering system are inadmissible.
On vehicles with two mechanically steered front axles (e.g. 8x4) steered axles may only be moved by MAN suppliers.
TRUCKNOLOGY
Provided guidelines listed here are followed, shortening the wheelbase is possible for these models using:
Moving axles
The axle-mounting brackets, axle locating hardware and cross-members should be completed using rivets or MAN double nip
countersunk bolts to MAN Standard M 7.012.04 (may be sourced via www.normen.man-nutzfahrzeuge.de) as described in Section 4.3.
Observe the hole-to-hole distances specied there!
Welding
The guidelines on welding in this Guide to Fitting Bodies (see Chapter 4.4.1) must be observed. If frame components are to be inserted,
such as longitudinal frame members, frame inserts, the original frame material must be used. For frame materials see Chapter 4.1.
It is recommended that the longitudinal frame members are pre-heated to 150C 200C.
The frame must not be disconnected in the vicinity of:
Points where loads are introduced from the body
Bends in the frame, minimum distance 100 mm
Axle guides and suspension (e.g. spring hangers, trailing arm mountings), minimum distance 100mm
Transmission mountings (including transfer cases on all-wheel drive vehicles), engine mountings
The allowable area for welds when performing wheelbase modications lies between the bend in the frame and the front-most rear axle
guide. Welded seams along the longitudinal axis of the vehicle are not permitted!
Position of weld seams see Fig. 22.
Fig. 22: Allowable weld area ESC-501
If changing the wheelbase involves disconnecting the longitudinal frame members, the weld seams must be secured with inserts, in
accordance with Fig. 23 or Fig. 24.

550
= =
2
50
50
25 25
1
= =
1
2
3
3
4
0

TRUCKNOLOGY
Use the existing drill holes in the frame in the vicinity of the angle
inserts. Distance between drill holes 50, Distance between edges 25
Level the weld seam where parts should be in contact.
Weld seam by assessment group BS, DIN 8563, part 3.
Use prole sections with equal ange lenghts.
Width is the same as the inner width of the frame. Tolerance - 5 mm.
Thickness same as frame thickness. Tolerance -1. Material min. S355J2G3 (St52-3)
Fig. 23: Inserts for shortening the wheelbase ESC-012
2
1
4
3
300
50
50
25 25
375
4
0

1
2
3
4
TRUCKNOLOGY
Use the existing frame drill holes in the area of the angle inserts.
Angle inserts must be of one piece.
Distance between drill holes 50, edge distance 25
Level the weld seam where parts should be in contact.
Weld seam by assesment group BS, DIN 8563, part 3.
Use prole sections with equal ange lengths.
Width is the same as the inner width of the frame. Tolerance -5.
Rolled sections are not permitted.
Thickness same as frame thickness. Tolerance -1. Material S355J3G3 (St52-3)
Extend the wheelbase using a section of the original frame longitudinal member.
Material as stated in the Guide to Fitting Bodies, frame prole list.
Observe max. distance between frame cross members as stated in the Guide to Fitting
Bodies.
Fig. 24: Inserts for extending the wheelbase ESC-013
On some long-wheelbase chassis, frame inserts are already tted between the front and rear axles at the factory.
Frame inserts may not be welded together with the longitudinal frame members. This can be avoided for example, by inserting
a copper-based separating foil which is removed once the welding work is completed. Inserts used in changing the wheelbase may be
simply butted-up to one another and may either be welded together or joined with an overlapping plate (see Fig. 25).
TRUCKNOLOGY
Fig. 25: Overlapping inserts on inside and outside ESC-504
The section point between the frame and the insert joint may not coincide with a welded joint in the frame.
A distance between the joints of 100 mm must be observed. This is easy to achieve if during cutting of the frame the location of
the frame-insert joint is already taken into account.
Fig. 26: Overlapping insert on inside and outside ESC-505

TRUCKNOLOGY
4.5 Retrotting additional equipment add-on components or accessories
The manufacturer of an assembly, add-on component or accessory must co-ordinate the installation with MAN.
Retrot installation of components frequently requires intervention in the control units CAN architecture .
Such work always requires modication of the vehicle parameterisation. Retrotted systems may, under certain circumstances,
not be assimilated into the vehicles on-board Trucknology
systems Time maintenance system of Flexible maintenance system.

For this reason it is not possible to achieve the same degree of maintenance convenience as is possible with original equipment.
Subsequent modication or expansion of the vehicle parameterisation can only be carried out with the help of the electronics
specialists at MAN service centres with subsequent approval by MAN. As a result, retrot installation of components must be agreed
with MAN (for address see Publisher above) at the planning stage. MAN will rst check to see if it is actually possible to carry out the
planned work. For the approval procedure it is essential therefore, that full and veriable documentation be provided.
Under no circumstances does MAN accept responsibility for the design or for the consequences of non-approved retrotted equipment.
The conditions stated in this Guide and in the approvals must be observed. Approvals, reports and clearance certicates that have
been compiled by third parties (e.g. test and inspection authorities) do not automatically mean that MAN will also issue approval.
MAN reserves the right to refuse approval even though third parties may have issued clearance certicates.
Unless otherwise agreed, approval only refers to the actual installation of the equipment. Approval does not mean that MAN has
checked the entire system with regard to strength, vehicle handling etc., and has accepted responsibility for warranty of products.
The responsibility for this lies with the company carrying out the work. Retrotting of equipment may change the vehicles technical
data. The equipment manufacturer and/or the dealer / importer is responsible for determining and issuing this new data.

4.5.1 Retrotting additional or larger fuel tanks after factory delivery
Fuel is taxed at different rates even within the EU. If larger or additional fuel tanks are tted after the vehicle has been delivered from
the manufacturers factory then the additional tank volume becomes subject to the mineral oil excise duty applicable in the country into
which it is being imported upon crossing the border. Only fuel that is carried in the so-called standard tanks (plus fuel carried in
reserve fuel canisters up to a maximum quantity of 20 litres) is free of duty. Standard tanks are the fuel tanks tted to the vehicle
when it was delivered from the factory and not fuel tanks added at a later time by a body builder or workshop for example.
TRUCKNOLOGY
4.6 Propshafts
Jointed shafts located in areas where people walk or work must be encased or covered.
Depending on the local legislation in the country where the vehicle is used, it may be necessary to t a retaining cable or arrester
bracket to the propshaft.
4.6.1 Single joint
When a single cardan joint, universal joint or ball joint is rotated uniformly whilst bent it results in a non-uniform movement on
the output side (see Fig. 27). This non-uniformity is often referred to as cardan error. The cardan error causes sinusoidal-like
uctuations in rotational speed on the output side. The output shaft leads and trails the input shaft.
The output torque of the propshaft uctuates in line with this, despite constant input torque and input power.
Fig. 27: Single joint ESC-074
Because acceleration and deceleration occur twice during each revolution, this type of propshaft and layout cannot be permitted for
attachment to a power take-off. A single joint is feasible only if it can be proven without doubt that because of the
mass moment of inertia
rotational speed and
the angle of deection
the vibrations and loads are not signicant.
2
TRUCKNOLOGY
c
o
m
m
o
n
d
e
e
c
tio
n
p
la
n
e
c
o
m
m
o
n
d
e
e
c
tio
n
p
la
n
e
4.6.2 Jointed shaft with two joints
The non-uniformity of the single joint can be compensated for by combining two single joints in one propshaft. However, full compensati-
on of the movement can be achieved only if the following conditions are met:
Both joints have the same working angle, i.e.
1
=
2
The two inner yokes of the joint must be in the same plane
The input and output shafts must also be in the same plane, see Figs. 28 and 29.
All three conditions must always be met simultaneously so that the cardan error can be compensated for.
These conditions exist in the so-called Z and W arrangements (see Figs. 28 and 29). The common working plane that exists for Z or W
arrangements may be freely rotated about the longitudinal axis. The use of the W-arrangement should be avoided in practice.
The exception is the three-dimensional propshaft layout, see Fig. 30.
Fig. 28: W propshaft layout ESC-075
Fig. 29: Z propshaft layout ESC-076

R1
R2
TRUCKNOLOGY
A
ngle of offset
Plane I
formed by shafts 1 and 2
Plane II
formed by shafts 2 and 3
Fork in plane I Fork in plane II
4.6.3 Three-dimensional propshaft layout
If the input and output shafts are not in the same plane the layout is three-dimensional. The centre lines of the input and output shafts
are not parallel. There is no common plane and therefore, to compensate for the uctuations in angular velocity, the inner yokes (forks)
of the joint must be offset by angle (Gamma) - see Fig. 30.
Fig. 30: Three-dimensional propshaft layout ESC-077

The condition that the resulting working angle
R1
on the input shaft must be exactly the same as the working angle
R2
on the output
shaft still applies.
Therefore:

R1
=
R2
Where:

R1
= three-dimensional angle of shaft 1

R2
= three-dimensional angle of shaft 2.
Three-dimensional working angle
R
is a function of the vertical and horizontal angle of the propshafts and is calculated as:
Formula 10: Three-dimensional working angle

tan
2

R
= tan
2

v
+ tan
2

h

The required angle of offset (Gamma) can be calculated using the joint angles in the horizontal and vertical planes as follows:
Formula 11: Angle of offset

tan
h1
tan
h2
tan
1
= ; tan
2
; =
1
+
2
tan
1
tan
2
Where:

R
= Three-dimensional working angle

= Vertical working angle

h
= Horizontal working angle
= Angle of offset.
TRUCKNOLOGY
Note:
In the case of three-dimensional offset of a propshaft with two joints only the three-dimensional working angles need to be equal.
In theory therefore, an innite number of layout options can be achieved from the combination of the vertical and horizontal working
angles.
We recommend that the manufacturers advice be sought for determining the angle of offset of a three-dimensional propshaft layout.
4.6.3.1 Propshaft train
If the design dictates that greater lengths have to be spanned, propshaft systems comprising two or more shafts may be used.
Fig. 31 shows three basic forms of propshaft system in which the position of the joints and the drivers with respect to each other were
assumed to be arbitrary. Drive dogs and joints are to be matched to each other for kinematic reasons. Propshaft manufacturers should
be consulted when designing the system.
Fig. 31: Propshaft train ESC-078
4.6.3.2 Forces in the propshaft system
The joint angles in propshaft systems inevitably introduce additional forces and moments. If a telescoping propshaft is extended or
compressed whilst under load whilst under load further additional forces will be introduced.
Dismantling the propshaft, twisting the two halves of the shaft and then putting them back together again will not compensate for
the imbalances, it is more likely to exacerbate the problem. Such trial and error may cause damage to the propshafts, the bearings,
the joint, the splined shaft prole and assemblies. It is therefore essential that the markings on the propshaft are observed.
The marks must therefore be aligned when the joints are tted (see Fig. 32).
1
TRUCKNOLOGY
Fig. 32: Marking on propshaft ESC-079
Do not remove existing balancing plates and do not confuse propshaft parts otherwise imbalances will occur again.
If one of the balancing plates is lost or propshaft parts are replaced, the propshaft should be re-balanced.
Despite careful design of a propshaft system, vibrations may occur that may cause damage if the cause is not eliminated.
Suitable measures must be used to cure the problem such as installing dampers, the use of constant velocity joints or changing
the entire propshaft system and the mass ratios.
4.6.4 Modifying the propshaft layout in the driveline of MAN chassis
Body manufacturers normally modify the propshaft system when:
Modifying the wheelbase as a retrot operation
Installing pumps on the driveshaft ange of the power take-off.
In such cases the following must be observed:
The working angle of each cardan shaft in the driveline must be 7 maximum in each plane when loaded.
If propshafts are to be extended the entire propshaft system must be re-designed by a propshaft manufacturer.
Modications to the propshaft, such as extensions, may only be carried out by authorised workshops
Every propshaft must be balanced before installation.
Allowing the propshaft to hang on one side when tting or removing it may lead to the shaft becoming damaged.
A clearance of at least 30mm must be maintained.
When assessing the minimum clearance, the raising of the vehicle and associated movement of the axle due to the extension of the
springs and resulting change in position of the propshaft must be taken into consideration.
4.7 Modifying the wheel formula
Modifying the wheel formula means:

The installation of extra axles
The removal of axles
Changing the type of suspension (e.g. from leaf suspension to air suspension)
Making non-steered axles steerable
Modications to the wheel formula are prohibited.
Such conversions are only to be carried out by MAN Truck & Bus and its suppliers.
4.7.1 Safety-related components
Modications and changes to the following components:
Axle guide members (e.g. on control arms)
The steering system (e.g. on the steering arm)
Suspension (e.g. stabilisers)
The braking system
together with their mountings and fastenings are not permitted.
Suspension components or spring leaves may not be removed or modied. Leaf springs may be replaced only as a complete part and
only in pairs (left and right-hand side).
60

1
0
0

6
0

2
4
0
420
420
TRUCKNOLOGY
4.8.1 Basics
If the truck is intended to pull loads, the equipment required to do this must be tted and approved. Compliance with the minimum engine
power required by legislation and/or the installation of the correct trailer coupling does not provide any guarantee that the truck is
suitable for pulling loads. MAN (for address see Publisher above) must be contacted if the standard or
ex-works permissible gross vehicle weight is to be changed.
Contact must not occur between the truck and the trailer during manoeuvring. Adequate drawbar lengths should therefore be selected.
The legal requirements pertaining to trailer couplings (EU: 94/20/EC and country-specic regulations) as well as the required clearances
must be observed (in Germany, these are dened in DIN 74058 and EC Directive 94/20/EC).
The bodybuilder is obliged to ensure that the body is designed and constructed such that the coupling process can be performed and
monitored unhindered and without incurring any risks. The freedom of movement of the trailer drawbar must be guaranteed. If coupling
heads and sockets are installed offset to one side (e.g. on the drivers side rear light holder) the trailer manufacturer and vehicle operator
must ensure that the cables/pipes are long enough for cornering.
Fig. 33: Clearances for trailer couplings in accordance with 94/20/EC ESC-006

1
4
0
m
i
n
.
A A
250max.
300max.
R
2
0
m
a
x
.
R
4
0
m
a
x
.
100max.
4
5
m
a
x
.
3
0
m
a
x
.
3
0
m
a
x
.
6
5
m
i
n
.
300max.
5
5
m
i
n
.
3
2
m
i
n
.
3
5
0
m
i
n
.
4
2
0
m
a
x
.
4
5
m
i
n
.
7
5
m
i
n
.
7
5
m
i
n
.
100max.
15max.
30max.
65min.
TRUCKNOLOGY
Fig. 34: Clearances for trailer couplings in accordance with DIN 74058 ESC-152
Only original MAN end cross members and their associated reinforcement plates may be used when tting trailer couplings.
End cross members have a hole pattern that matches that of the associated trailer coupling. This hole pattern may under no
circumstances be modied to suit a different trailer coupling. The guidelines provided in the coupling manufacturers installation
instructions must be observed (e.g. tightening torques and their checking).
Lowering the trailer coupling without also lowering the end cross member is not permitted!
Some examples of how the coupling may be lowered are shown in Figs. 35 and 36.
These examples are purposely represented only schematically they do not form a design instruction.
Design responsibility rests with the respective bodybuilder/ converter.
Fig. 35: Lowered trailer coupling ESC-515
TRUCKNOLOGY
Fig. 36: Trailer coupling tted below the frame ESC-542
4.8.2 Trailer coupling, D value
See the booklet Coupling devices TG for detailed derivation of the D value and for rigid drawbar trailers D
c
and V values.
Example calculations can be found in the Calculations Chapter 9.
4.9 Tractor units and converting the vehicle type - truck / tractor
4.9.1 Articulated vehicles
The weight and size of semitrailers and semitrailer tractors must be checked to see if they are suitable for forming an articulated vehicle.
The following must therefore be checked:
Slew radii
Fifth-wheel height
Fifth-wheel load
Freedom of movement of all parts
Legal requirements.
In order to achieve maximum fth-wheel load the following actions are required before the vehicle goes into operation:
Weigh the vehicle
Calculate the axle loads
Determine the optimum fth-wheel lead
Check the front slew radius
Check the rear slew radius
Check the front angle of inclination
Check the rear angle of inclination
Check the overall length of the articulated vehicle
Install the fth-wheel coupling accordingly.
TRUCKNOLOGY
The required angles of inclination are 6 to the front, 7 to the rear and 3 to the side, in accordance with DIN-ISO 1726.
Different tyre sizes, spring ratings or fth-wheel heights between tractor unit and semitrailer may possibly reduce these angles so that
they no longer comply with the standard. In addition to the inclination of the semitrailer to the rear the following must also be taken into
account: Body roll when cornering, suspension compression travel (axle guide, brake cylinder, wheel covers), antiskid chains,
the pendulum motion of the axle unit on vehicles with tandem axles and the slew radii.
The plane of the fth-wheel pick-up plate on the semitrailer should run parallel with the road at permissible fth-wheel load.
The height of the fth-wheel coupling and/or its mounting plate must therefore be designed accordingly.
Fig. 37: Dimensions for semitrailer tractor units ESC-402
The fth-wheel lead, as stated in the sales documentation or the chassis drawings, is applicable to the standard vehicle only.
Under some circumstances, equipment that affects the vehicles unladen weight or dimensions requires, among others, the fth-wheel
lead to be modied. This can also change the payload capacity and the combinations overall length.
Only type-approved fth-wheel couplings and mounting plates that comply with Directive 94/20/EC may be used.
Installing a fth-wheel coupling without a subframe is not permitted. Under certain circumstances it is possible to t a fth-wheel coupling
directly. Here, the fth-wheel coupling is installed on the subframe together with special bearing brackets and a reinforcing plate
(not subject to type approval) and the mounting plate is omitted.
The size of the subframe and the quality of the material (
0,2
> 350 N/mm
2
) must be equivalent to those used on a comparable production
vehicle. The fth-wheel coupling base plate must lie only on the fth-wheel subframe and not on the frame longitudinal members.
The mounting plate must only be attached using bolts approved by MAN or by the fth-wheel coupling base plate manufacturer. When
tting the fth-wheel coupling and mounting plate observe the instructions/guidelines provided by the fth-wheel coupling manufacturer.
TRUCKNOLOGY
Connecting pipes/cables for air supply, brakes, electrics and ABS must not chafe on the body or snag during cornering.
The bodybuilder must therefore check the freedom of movement of all cables/pipes when cornering with a semitrailer.
When operating without a semitrailer, all pipes/cables must be attached securely in dummy couplings or connectors.
Furthermore, these connections must be tted such that all pipes/cables can be safely connected and disconnected.
If it is not possible to connect the air and electrical pipes/cables from road level then a suitable working platform measuring at least
400 mm x 500 mm together with access steps to the platform must be provided.
The following fth-wheel kingpins are available:
Fifth-wheel kingpin, size 50 of 2 diameter
Fifth-wheel kingpin, size 90 of 3.5 diameter
Which one is to be used depends on various factors. As for trailer couplings, the deciding factor is the D value.
The smaller of the two D values for the kingpin and the fth-wheel coupling applies for the articulated vehicle as a whole.
The D value itself is marked on the model plates:
Formula 12: D value for fth-wheel coupling
0,6 9,81 T R
D =
T + R - U
If the D value is known, the following formula is applied to calculate the permissible gross weight of the semitrailer:
Formula 13: Permissible gross weight of the semitrailer
D (T - U)
R =
(0,6 9,81 T) - D
If the permissible gross weight of the semitrailer and the D value of the fth-wheel coupling are known, the permissible gross weight of
the semitrailer tractor unit can be calculated with the following formula:
Formula 14: Permissible gross weight of the tractor unit
D (R - U)
T =
(0,6 9,81 R) - D
If the fth-wheel load is required and all other loads are known, the following formula can be used:
Formula 15: Fifth-wheel load
0,6 9,81 T R
U = T + R -
D
TRUCKNOLOGY
Where:
D = D value [ in kN ]
R = Permissible gross weight of the semitrailer [ in t ], including the fth-wheel load
T = Permissible gross weight of the semitrailer tractor [ in t ], including the fth-wheel load
U = Fifth-wheel load [ in t ]
Examples of calculations can be found in the Calculations Chapter 9.
4.9.2 Converting trucks into tractor units or tractor units into trucks
Conversion of a truck into a tractor unit or of a tractor unit into a truck or using the same vehicle alternatively as a tractor unit or truck
requires approval from MAN. MAN can provide further information (for address see Publisher above).
When converting a tractor unit to a truck or vice-versa, it is necessary to modify the vehicles EBS (brake) parameterisation.
Depending upon the vehicle undergoing conversion (leaf suspension), this may also involve installing different rear springs.
Due to the rear axle guide member, possible equipment with fth wheel ESP and fth wheel level adjustment, two-axle tractor units
with wheel formulae 4x2 and 4x4H can only be used as semitrailer tractors. Operation as a combined articulated vehicle/truck is not
permitted.
Models as of 03-2010: 05X, 06S, 06X, 08S, 10S. 10X, 13S, 13X, 22S, 22X, 78 X. Therefore, in the case of new-build vehicles to
be used as both tractor units and trucks, always select a truck chassis as a basis. Exceptions, even in connection with further vehicle
conversions require written approval from MAN (for address see Publisher above).
An exception are car transporters, see Chapter 5.4, Bodies.
4.10 Modifying the cab
4.10.1 General
Modications to the cabs structure (e.g. incisions/cut-outs, changes to the support structure including the seats and seat mountings,
cab extensions) together with modications to the cab mountings and tilting mechanism are prohibited. Such modications are only
to be carried out by qualied MAN Truck & Bus AG and its qualied conversion suppliers.
4.10.2 Spoilers, roof extensions, roofwalk
It is possible to retrot a roof spoiler or an aerodynamics kit. Original MAN spoilers and aerodynamics kits can be obtained for retrotting
from our spare parts service. Drawings can be found in MANTED
under Cabs. Only the proper mounting points on the cab roof should
be used when retrotting components to the cab roof.
Pos 11
Pos 13
Pos 12
Pos 15
Pos 14
Pos 3
Pos 4
Pos 16
Pos 17
Pos 18
Pos 19 Pos 7
Pos 8
Pos 9
Pos 10
Pos 7
Pos 8
Pos 9
Pos 10
Pos 11
Pos 12
Pos 13 Pos 14
Pos 15
Pos 16
Pos 17
Pos 18
Pos 19
Pos 4
Pos 3
Pos 3
Pos 7
Pos 8
Pos 9
Pos 10
Pos 13
Pos 16
Pos 14
Pos 15
Pos 17
Pos 18
Pos 19
Pos 12
Pos 11
Pos 4
Pos 26
Pos 25
Pos 24
Pos 23
Pos 22
Pos 20
Pos 21
TRUCKNOLOGY
Attachments on cab roofs
Fig. 38a: XXL-Fhs (L/R45) ESC-506a Fig. 38b: XLX-Fhs (L/R49) ESC-506b
Fig. 38c: LX-Fhs (L/R39) ESC-506c Fig. 38d: XL; L und M-Fhs (L/R 44; 34; 17) ESC-506d
TRUCKNOLOGY
Table 17: Attachment points on cab roofs
Position Bolts / drillings Tightening torque
Roof spoilerwith plastic high roof
3/3a
4/4a
M8 20 Nm
Roof spoilerwith steel high roof
24/24a
25/25a
26/26a
M8 20 Nm
Sun blindwith steel roof
20/20a
21/21a
22/22a
23/23a
M8 20 Nm
Sun blindwith plastic high roof
7/7a
8/8a
9/9a
10/10a
St 6,3 /
5,5 mm
10 Nm
Air hornwith plastic high roof
14/14a
15/15a
16/16a
17/17a
18/18a
19/19a
St 6,3 /
5,5 mm
10 Nm
Rotating beacons with plastic high roof
11/11a
12/12a
13/13a
St 6,3 /
5,5 mm
10 Nm
Drilling description a is symmetric with y = 0
Maximum load per bolt: 5kg
Maximum roof load: 30kg
Bolted connections over 3 offset points (not in one line)
Centre of gravity of roof extensions max. 200mm above the reference plane for the required bolting
drillings in the plastic raised roof (laminated-in plates):
- Drill axis parallel to the surface
- Drilling at an angle of 2 mm to the surface
- Drilling depth 10 mm +2 mm
Pos 2
Pos 1
TRUCKNOLOGY
Information on tting a roofwalk:
Table 18: Additional attachments for roofwalk
Position Bolts / drillings Tightening torque
Roofwalk on rear wall (all cabs)
1/1a
2/2a
M8 /
11,2 mm
20 Nm
Fig. 38e: Additional attachments for roofwalk ESC-506e
A support for the roofwalk must be tted to the rear wall
All 4 mounting points 1/1a, 2/2a must be used
The roofwalk must never be installed ahead of the rear edge of the roof hatch
maximum weight of the roofwalk must not exceed 30 kg
maximum roofwalk load 100 kg.
y
825
825 10%
8
2
0

1
0
%

5
6
0

y

TRUCKNOLOGY
Centre of gravity
of top sleeper
Resulting centre
of gravity
Dimension will be determined by
the body builder
Cab oor
Cab centre of
gravity
approx. 660 kg
4.10.3 Roof sleeper cabs
It is possible to install roof sleeper cabs (top-sleepers) and raised roofs provided that the following conditions are met:
Approval must be obtained from MAN. This is the responsibility of the roof cab manufacturer and not the workshop carrying
out the work; see Section 4.5 Retrotting additional equipment add-on components or accessories in this Guide to Fitting
Bodies.
The manufacturer of the roof cab is responsible for compliance with regulations (in particular safety regulations, e.g.
trade association guidelines), regulations and laws (e.g. GGVS/ADR).
A suitable method of preventing the cab from closing by itself when it is tilted must be installed (e.g. by tting a securing device)
If the tilting process differs from that for the standard MAN cab, a simple but comprehensive operating manual must be drawn up.
The resulting centre of gravity of the extended cab must be in line with the specications, and evidence of this compliance
must be provided (see Fig. 39).
Roof sleeper cabs may only be installed on vehicles tted with an air suspended cab.
The maximum weights listed in table 19 are to be observed.
The antennas tted on original MAN cab roofs must be properly moved. This is intended to ensure good quality reception and
transmission of electromagnetic radiation in accordance with the EMC Directive. Extension of the antenna cable
(by splicing extra cable lengths in) is not permitted.
Fig. 39: Cab centre of gravity with roof sleeper cab ESC-410
TRUCKNOLOGY
Table 19: Roof cab, maximum weights of tted/installed components
Cab designation Technical code Requirements max. mass of roof cab
incl. equipment
LHD RHD
M F99 L17 S F99 R17 S Air-suspended cab 130 kg
L F99 L34 S F99 R34 S 180 kg
XL F99 L44 S F99 R44 S 200 kg
LX F99 L39 S F99 R39 S Modications to factory tted high roof cabs
are not permitted
XLX F99 L49 S F99 R49 S
XXL F99 L45 S F99 R45 S
4.11 Add-on frame components
4.11.1 Rear underride guard
TGS/TGX-chassis are factory-tted with MAN rear underride guards in various variants.
The choice of variant is controlled by MAN depending on the following parameters:
wheelbase formula, overall height, suspension type and wheelbase in combination with the works body (swap body ttings)
(see table 20). MAN underride guards are approved in accordance with Directive 70/221/EEC, latest amendment contained in 2006/20/EC.
Table 20: Underride guard variants (for and explanation of the values see g. 40)
Underride guards
tted by MAN
Version w x Y Z
81.41660-8176 C2
WB
191 mm max. 348 mm 340 mm max. 550 mm 56,3
81.41660-8177 C1 199 mm max. 332 mm 432 mm max. 550 mm 33,8
81.41660-8178 C2 291 mm max. 348 mm 340 mm max. 550 mm 56,3
81.41660-8180 B1 249 mm max. 318 mm 507 mm max. 550 mm 33,8
81.41660-8181 B2 366 mm max. 339 mm 391 mm max. 550 mm 56,3
81.41660-8183 A1 277 mm max. 305 mm 549 mm max. 550 mm 33,8
81.41660-8184 A2 408 mm max. 330 mm 418 mm max. 550 mm 56,3
The bodybuilder must check that statutory regulations are complied with and ensure that these requirements are adhered to because
the dimensions are dependent on the body and can only be determined when the vehicle, including the body, has been completed.
x
y
z
w
TRUCKNOLOGY
Body
Frame
Fig. 40: Dimensional specications for underride guard ESC-522
The following dimensions must be observed:
w = horizontal distance from frame end to rear edge of the underride guard.
y = vertical distance from frame lower edge to lower edge of the underride guard.
x = maximum permissible horizontal distance from the rear edge of the underride guard to the rear edge
of the body.
z = vertical distance from the lower edge of the underride guard to the road surface for an unladen vehicle,
maximum permissible in accordance with Directive 70/221/EEC is 550 mm.
= angle depends upon the requirements for dimensions w and y.
Depending upon the chassis variant, a folding underride guard from Ringfeder VBG is available as optional equipment
for vehicles tted with a MAN low coupling system. Alternatively, a folding underride guard for construction site vehicles is available from
Meiller. Never attempt to modify approved underride guards (no changes to weld seams, drill holes, angle) because this will invalidate
the certication/type approval! This also applies to vehicles with a factory tted body!
If rear underride guards are retrotted or retted, e.g. after shortening the frame, the bodybuilder/modier is responsible for tting a rear
underride guard in accordance with the regulations.
The following points must then be observed:
For the bolted connections between the bracket and frame it is imperative that MAN Verbus-Ripp bolts with shaft are used
(MAN 06.02813-4915, M14x1.5 10.9), tightening torque 200 Nm on the nut side (see Fig. 41).
At the lower bolted connections of the underride guard the bolts must be tightened with a torque of 330 Nm. (See Fig. 42)
Angle of the underride guard may not be modied at a later time, otherwise the certication will become void.
Any modications to the underride guard must be certied by an ofcially approved inspector
(e.g. an ofcially recognised expert in Germany).
TRUCKNOLOGY
Fig. 41: Bolted connection underride guard ESC-523 Fig.42: Lower bolted connection, underride guard bracket ESC-524
4.11.2 FUP - front underride protection
Motor vehicles used for the transport of goods that have at least four wheels and a maximum permissible mass of over 3.5 t must be
tted with front underride protection that is approved in accordance with Directive 2000/40/EC. This shall not apply to:
off-road vehicles, and
vehicles that are used for purposes incompatible with the provisions of front underrun protection.
Vehicles that do not meet the criteria for an off-road vehicle are tted with FUP that complies with the requirements of Directive 2000/40/
EC. Do not modify these underride protection devices (e.g. by modifying welded seams, drill holes, brackets) because this will invalidate
the certication/design approval! All-wheel-drive vehicles (wheel formulae e.g. 4x4, 6x6, 6x6-4, 8x6 and 8x8) and vehicles that full the
so-called off road criteria can be approved as off-road vehicles and are therefore not tted with front underride protection at the factory.
Ensure therefore, that the criteria for approval as an off-road vehicle is complied with.
The criteria are:
At least 50% of the wheels are driven
A differential lock or ASR is tted
Gradeability of the individual vehicle 25%
Plus at least 4 of the following requirements:
- Approach angle 25
- Departure angle 25
- Ramp angle 25
- Ground clearance beneath the front axles at least 250 mm
- Ground clearance beneath the rear axles at least 250 mm
- Ground clearance beneath the axles at least 300 mm
a a l

3
0
0

3
5
0

5
5
0
TRUCKNOLOGY
Body
If it is not possible to locate bodies and ancillaries (e.g. outriggers, tool boxes) such that the above stated criteria are not violated then
the vehicle must be retrotted with front underride protection that is available from the MAN spare parts organisation.
Responsibility for this lies with the body builder. MAN is not liable for any costs arising from the retrotting of front underride protection
to vehicles that were delivered as off-road vehicles.
4.11.3 Sideguards
Side guards (= SSV) protect vulnerable road users from the risk of falling sideways under the vehicle and being run over by the wheels.
Trucks, tractor units and their trailers with a permissible gross weight of > 3.5 t must be tted with sideguards (= SSV).
Exceptions applicable to the truck sector are as follows:
Vehicles that are not yet completed (chassis atng delivered)
Tractor units (not semitrailers)
Vehicles built for special purposes that are incompatible with the tting of sideguards.
In this connection, special vehicles mainly means vehicles with side tipper. This is only valid for vehicles with side tippers and a body
inside length of less then 7,500 mm. Neither vehicles for combined transport nor off-road vehicles are exempt from the mandatory r
equirement for tting SSVs.
For MAN chassis it is possible to obtain sideguards ex-works. If the body manufacturer is to retrot sideguards to the chassis, then
prole sections, prole supports and installation parts are available from MAN in a variety of designs. The company installing the
sideguards is responsible for compliance with legal regulations (regulated by Directive 89/297/EEC and in Germany by 32c StVZO
(Road Trafc Licensing Regulations).
It is not permissible to attach brake, air or hydraulic pipes to the sideguards; there may be no sharp edges or burrs; the rounding-off
radius for all parts cut to size by the bodybuilder must be at least 2.5 mm; rounded bolts and rivets may project by a maximum of 10 mm.
If the vehicle is tted with different tyres or different springs, the height of the guards must be checked and if necessary, corrected.
If there are several components in a row (battery box, tool box ) that serve as a form of SSV, a maximum distance of 25 mm is
permissible but the rear component may not project over the front component.
If it is necessary for the body builder to modify the original MAN sideguard prole then the relationship between the span I (= L2 in
the diagram) and projection a (= L3 in the diagram) apply as illustrated in the following diagram in accordance with Fig. 44. If, according
to expert opinion, the permitted dimensions are exceeded then the body builder must arrange for strength testing to be carried out.
The illustrations are only intended to clarify the dimensions for which the MAN sideguard strength requirements are met.
Fig. 43: TGA sideguards ESC-460
3
0
0
0
3
5
0
0
0
3
0
0
3
5
0
4
0
0
4
5
0
5
0
0
5
5
0
6
0
0
6
5
0
7
0
0
7
5
0
8
0
0
5
0
0
1
0
0
0
1
5
0
0
2
0
0
0
2
5
0
0
L
2

[
m
m
]
L 3 [ m m ]
TRUCKNOLOGY
V
e
r
s
i
o
n

w
i
t
h

t
w
o

s
i
d
e

g
u
a
r
d
s
V
e
r
s
i
o
n

w
i
t
h

o
n
e

s
i
d
e

g
u
a
r
d
s
Fig. 44: Graph for ascertaining the span and projection ESC-220
TRUCKNOLOGY
4.12 Modications to engine systems
4.12.1 Modications to the air intake system
In general modications to the air intake system are to be avoided. Various factory options are available for the TGS/TGX and body
builders should check to see if these can be used. Information on availability for the corresponding vehicle can be obtained from your
closest MAN sales branch.
If it is still not possible to avoid making modications the following requirements must be met:
The ow of intake of air must not be inhibited in any way.
The negative pressure in the intake branch must not be allowed to vary.
When modifying the intake system it must be ensured that all statutory regulations are fullled that are relevant to
noise and emissions.
All regulations pertaining to the components in question issued by professional associations or similar bodies must also
be fullled (e.g. surface temperature in the vicinity of handles/grips)
In the case of modied intake system
- MAN cannot guarantee compliance with these and other regulations.
Responsibility for this remains with the company performing the modication. This also applies to regulations
pertaining to on board diagnosis systems (OBD).
- MAN can provide no information about changes in fuel consumption or noise characteristics; in some circumstances
a new noise emission approval will be required. Components that have an effect on the vehicles acoustics
(e.g. nozzles in the air ter) may not be modied. If the noise limits are exceeded the type approval will become invalid!
For vehicles up to and including Euro 5, the following applies in addition to the general requirements:
Never change the shape or area of pipework cross-sections.
Sharp bends in the pipework should be avoided, mitre cuts are not permitted.
Do not modify air lters.
The service life of the air lter may be shortened when modications are made to the air intake.
Only approved air lter elements should be used.
The installation position of the humidity sensor in the air lter must not be changed.
The design of mountings and supports and the basic installation position of components must not be changed.
The air intake must be protected against ingesting warmed air (e.g. engine heat from the wheel arches or in the vicinity of
the exhaust silencer). A suitable position for the air intake must be chosen such that the intake air is not warmed by more
than 5C (difference between the ambient air temperature and the temperature at the turbocharger inlet). If the intake air
temperature is too high there is a risk that exhaust emission limits will be exceeded. If the exhaust emission limits are
exceeded the type approval will become invalid!
In order to avoid the ingestion of burning cigarette ends or similar a so-called cigarette mesh must be tted directly over the
air intake in the same fashion as the mesh installed on production vehicles (non-ammable material, mesh size SW6, area of
the open cross-section at least that of the intake air scoop on the air lter). There is a risk of vehicle re if this requirement is
not observed! MAN can provide no information on the effectiveness of the measure used, responsibility lies with the company
performing the modication.
The air intake must be positioned such that there is a low level of dust and spray ingestion.
Sufcient dewatering using water separation systems and unobstructed dust discharge from the lter housing and the
unltered side must be ensured otherwise damage may result.
Pipework on the ltered-air side must be selected to ensure that it is absolutely sealed from the unltered side. The inside
of the air intake pipes must be smooth no particles or similar may come loose from the sides. It is imperative that the air
intake pipe cannot slip out at the sealed joints. Suitable brackets must therefore be tted.
The vacuum sensor should be positioned in a straight section of the pipe at the shortest possible distance from
the turbocharger. It is the responsibility of the company carrying out the modication to ensure the sensor reads correctly.
TRUCKNOLOGY
Caution: Risk of engine damage if the sensor under reads!
All intake trunking must be capable of resisting vacuum pressures of 100mbar and temperatures of at least 80C
(peaks of 100C). Flexible tubing (e.g. hoses) are not permitted.
Modications to the air intake system may only be undertaken following written request and approval by MAN
(for address see Publisher above).
When installing the air compressor suction pipes, cross sections of sufcient size must be provided.
The pipe must have a vacuum stability of at least 250 mbar and a temperature stability range of between -40C and +120C.
Modications to the installed position, placement and alignment of sensors in the air intake system are not allowed.
Independent retrotting or removing of the safety elements (for difcult conditions) leads to non-compliance with
the emission limit values. Retrotting may only be carried out by MAN workshops. Under certain circumstances the vehicle
will require parameterisation.
4.12.2 Modications to exhaust gas routing for engines
In general modications to the exhaust systems are to be avoided. Various factory options are available for the TGS/TGX
and body builders should check to see if these can be used. The possible variants according to chassis type and engine can be found.
Information on availability for the corresponding vehicle can be obtained from your closest MAN sales branch.
If it is still not possible to avoid making modications the following requirements must be met:
The ow of outow of exhaust gases must not be inhibited in any way.
The backpressure in the exhaust must not be allowed to vary.
When modifying the exhaust or intake system it must be ensured that all statutory regulations are fullled that are relevant
to noise and emissions.
All regulations pertaining to the components in question issued by professional associations or similar bodies must also
be fullled (e.g. surface temperature in the vicinity of handles/grips)
In the case of modied exhaust systems
- MAN cannot guarantee compliance with these and other regulations. Responsibility for this remains with the company
performing the modication. This also applies to regulations pertaining to on board diagnosis systems (OBD).
- MAN can provide no information about changes in fuel consumption or noise characteristics; in some circumstances
a new noise emission approval will be required. Components that have an effect on the vehicles acoustics may not
be modied. If the noise limits are exceeded the type approval will become invalid!
- MAN can make no statements regarding compliance with the prescribed exhaust gas emission limits. It may be
necessary to obtain an emission certicate. If the emission limits are exceeded the type approval will become invalid!
If modications are made to the exhaust system and the exhaust gas routing then care must be taken to ensure that
the exhaust gas stream is not directed at any part of the vehicle and that the direction of the exhaust outlet points away from
the vehicle. (observe the relevant national regulations, in Germany this is the StVZO.
When moving the exhaust silencer it should be ensured that the original MAN bracket is re-used and the basic installation
position of components will be unchanged.
The position of the temperature and NO
x
sensors (where OBD is tted) on the exhaust silencer must not be changed.
Modications to the original MAN cable harness to the NO
X
sensor are not permissible.
If other cable harnesses are required, order original MAN cable harnesses from MAN spare-parts service.
CAN cables may not be untwisted as a result of EMC requirements.
Conversion work or modications to the exhaust gas routing from the exhaust manifold to the metal pipe (see Fig. 45)
are not permitted.
No blowing-out of products (e.g. bitumen) using exhaust gas pressure danger of damage to the exhaust system and engine.
Do not modify the cross-section (shape or area) of pipes. The original type of material must be used for pipes.
Do not modify silencers (including the silencer housing) in such a way that would invalidate the type approval.
TRUCKNOLOGY
Metal pipe
Support bracket
Temperature sensor
(On reverse)
NO
x
sensor (only on vehicles tted with OBD with
NO
x
analyser, mandatory from 10/2007)
When bending components, the bending radius must be at least double the diameter of the pipe.
The formation of wrinkles is not permissible.
Only continuous bends are permitted, i.e. no mitre cuts.
The function of the OBD relevant components may not be impaired. Should OBD relevant components be manipulated
the type approval will become invalid!
The connection of the pressure sensor tube on the silencer must always face the top, the following steel pipe must be
installed so that it rises continuously to connect with the sensor and it must have a minimum length of 300 mm and a maximum
length of 400 mm (including the exible section). The measurement line must be fabricated of M01-942-X6CrNiTi1810-K3-8x1
D4-T3. The general installation position of the pressure sensor must be retained (connection at bottom).
Heat-sensitive components (e.g. pipes, spare wheels) must be tted at least > 200 mm away from the exhaust; if heatshields
are tted, this clearance may be reduced to 100 mm.
For Euro 5 vehicles the following applies in addition to the lower emission standard requirements:
When moving the exhaust silencer it must be ensured that its original MAN support bracket is re-used.
Fig. 45: View of the exhaust silencer support bracket ESC-425
Extension of the exhaust routing by 1,000 mm is permissible from the metal pipe to the exhaust silencer without tting
high temperature insulation.
Extension of the exhaust routing by > 1,000 mm to max. 2,000 mm is permissible from the metal pipe to the exhaust silencer if
suitable high temperature insulation is tted.
TRUCKNOLOGY
Mixer
Metal pipe
Injection nozzle
Dosing module
Exhaust silencer
NO
X
sensor
Temperature sensor
Fig. 46: Exhaust tract, from mixer to metal pipe ESC-426
Only high-grade austenitic stainless steels may be used for manufacturing exhaust system piping. Reason: if otherwise
common ferritic steels are used, the ammonia (reaction product from AdBlue) will cause corrosion.
Stainless steel pipes must be welded using inert gas shielded arc welding (observe the steel manufacturers instructions)
with the work carried out by qualied and authorised personnel.
Fig. 47: Position of the NO
x
sensor (only vehicles with OBD and NO
X
analyser, mandatory from 10/ 2007) on the exhaust silencer)
ESC-427
TRUCKNOLOGY
Table 21: Overview of the austenitic stainless steels to be used in accordance with DIN 17440
Materials:
Description Material number
X 5 CrNi 18 10 1.4301
X 2 CrNi 19 11 1.4306
X 2 CrNiN 18 10 1.4311
X 6 CrNiTi 18 10 1.4541
X 6 CrNiNb 18 10 1.4550
X 5 CrNiMo 17 12 2 1.4401
X 2 CrNiMo 17 13 2 1.4404
X 6 CrNiMoTi 17 12 2 1.4571
X 2 CrNiMoN 17 13 3 1.4429
X 2 CrNiMo 18 14 3 1.4435
X 5 CrNiMo 17 13 3 1.4436
X 2 CrNiMoN 17 13 5 1.4439
For Euro 6 vehicles the following applies:
Changing the position of the exhaust gas silencer and modifying the routing of the exhaust pipe from the engine to the silencer
are impermissible.
Each modication to the exhaust end pipe must be assessed in relation to potentially increased noise generation. It may be necessary
to obtain a re-approval of the vehicle. Modifying the exhaust back-pressure compared to that of the factory installed exhaust system is
impermissible.
Damage to the lagging of the exhaust pipe is to be avoided. In the case of more serious damage it may become necessary
to replace the exhaust pipe.
Superstructures must be designed such that maintenance openings on the exhaust silencer are accessible and the lter element can
be removed and replaced.
TRUCKNOLOGY
AdBlue
feed pipe
AdBlue
pressure line
Dosing line
AdBlue
return pipe
Compressed air line
Air supply
AdBlue

tank Pump module Dosing modul Injection nozzle
4.12.3 Modications to the AdBlue
system
Before commencing with any modication work it should be checked to see if any of the existing MAN variations of the AdBlue
system
can be used. All vehicle modications must be carried out by qualied personnel.
AdBlue
(DIN 70070) is the trade name for an aqueous, synthetically manufactured 32.5% urea solution that is used for exhaust
gas after treatment in an SCR (selective catalytic reduction) catalytic converter.
Fig. 48: Schematic overview of the AdBlue
system in Euro 5 vehicles ESC-419

TRUCKNOLOGY
Pump module
Mixer, dosing module and
injection nozzle in the engine
area
Fuel ller inlet
AdBlue

filler inlet
AdBlue

tank for aqueous
urea solution
Cut-off valve between the tank
and the pump module pipe
Fig. 49: Overview of the relevant AdBlue
components on the vehicle overall ESC-420

Moving the AdBlue
tank
AdBlue
tanks all have four pipe connections and these are identied with a label so that the pipes are not mixed-up:
- AdBlue
feed and return lines (size 8.8x1.4, material PA-PUR, printed in yellow, pipe colour black)
- Engine coolant feed and return lines for heating the AdBlue
system(size 9x1.5, PA12-PHL-Y, printed in white,

pipe colour black)
Moving the combined/individual tank is only permissible if MAN original tanks are used and then only if a maximum pipe
length of 6.000 mm between the tank inlet and pump module inlet pipe is maintained
The routing of electrical and CAN cabling (e.g. for the ll level sensor, pump module, OBD sensors) is only permitted if original
MAN cable harnesses are used (available from the MAN spare parts service).
Moving the AdBlue
pump module
The pump module may only be moved to original MAN installation locations with the associated original MAN brackets.

Reason: strength/vibrations
< 1.0 m
< 1.0 m
> 0
> 0 > 0
TRUCKNOLOGY
Pump module
Original MAN bracket
AdBlue
- cable harness to
AdBlue
- tank
Lower edge of
the pump module
Source: Bosch installation guidelines
B
A
Fig. 50: Pump module and original MAN bracket ESC-421
When moving the pump module ensure that original MAN cable harnesses to the dosing module are used and that
the overall length does not exceed 3,000 mm.
The maximum possible height difference (delivery head) between the lower edge of the pump module and the lower edge
of the tank or the upper edge of the tank (and uppermost pipe position) may not exceed 1,000 mm.
Should the specications not be adhered to the warranty will be rendered invalid.
Fig. 51: Installation overview ESC-422
TRUCKNOLOGY
The chassis drawing depicts a production standard basic vehicle without special equipment tted.
For special equipment such as different fuel tanks, additional tanks for air suspension in order to accommodate frame adjustments/
swap body mountings or silencer variants with raised endpipes a position that deviates from standard may be necessary according to
the particular application.
Tables 22 and 23 dene the respective dosing module position for solo trucks and tractor units dependant upon the wheel formula,
cab and optional equipment.
The dosing module position associated with the respective variant is depicted in Figs. 5262.
Table 22: Possible positions for the AdBlue
system dosing module for solo trucks:

Wheel formula Cab Fuel tank Exhaust Variant Additional information
4x2, 4x4H,
6x2/2, 6x2/4,
6x2-2, 6x2-4,
6x4H-2, 6x4H-4,
6x4, 6x6H
L - XXL AdBlue single tank
Left-hand side mounted
exhaust, production
standard
1
Caution! Also applies to the
M cab, if tted with additional
tanks for air suspension in order
to accommodate frame
adjustments/swap body
mountings
4x2, 4x4H,
6x2/2, 6x2/4,
6x2-2, 6x2-4,
6x4H-2, 6x4H-4,
6x4, 6x6H
6X4H/2, 6X4H/4
M - XXL
AdBlue/Diesel
combi tank
exhaust, production
standard
2
Caution! Change to variant 1 if
tted with additional tanks for air
suspension in order to
accommodate frame
adjustments/swap body
mountings. 6x4, 6x6H, 6x4H-4
(71S)
from June 2010
6x4, 6x6H, 6X4H-4
M
AdBlue/Diesel
combi tank
exhaust, production
standard
3
6x4, 6x6H, 6x4H-4 (71S)
Up to May 2010
4x2, 4x4H,
6x2/2, 6x2/4,
6x2-2, 6x2-4,
6x4H-2, 6x4H-4,
6x4, 6x6H
AdBlue/Diesel
combi tank
Exhaust with raised endpipe
8x4-4 All variants All variants
4x2, 4x4H, 6x4,
6x6H, 6x2-2,
6x2-4, 6x4H-2,
6x4H-4, 6x2/2, 6x2/4
4x4, 6x4-4, 6x6
AdBlue single tank All variants
8x2-4, 8x2-6,
8x4, 8x4H-6,
8x6, 8x6H, 8x8
M AdBlue single tank All variants 4
Only possible with AdBlue
single tank
4x2, 4x4H,
6x2/2, 6x2/4,
6x2-2, 6x2-4,
6x4H-2, 6x4H-4,
6x4, 6x6H
L - XXL All variants Exhaust with raised endpipe 5

8x2-4, 8x2-6,
8x4, 8x4H-6,
8x6, 8x6H, 8x8
L - LX AdBlue single tank All variants 6
Only possible with AdBlue
single tank
TRUCKNOLOGY
Table 23: Possible positions for the AdBlue
system dosing module for tractor units:

Wheel formula Cab Fuel tank Exhaust Variant Additional information
4x2, 4x4H,
6x2-2, 6x2-4,
6x4, 6x6H
M - XXL
All variants
exhaust, production
standard
1
Bodywork limitations possible
with the M cab E.g.: crane
behind cab or swap body
tractor unit/solo truck
6x2/2, 6x2/4,
6x2-4, 6x4H-2,
6x4H-4
Single tank
4x2, 4x4H,
6x2/2, 6x2/4,
6x2-2, 6x2-4,
6x4H-2, 6x4H-4,
6x4, 6x6H
M
Combi tank
Exhaust with raised endpipe
3
Bodywork limitations
possibleE.g.: crane behind
cab or swap body tractor unit/
solo truck
4x2, 4x4H,
6x4, 6x6H,
4x4, 6x6
Single tank
4x4, 6x4-4, 6x6 Left-hand side mounted
exhaust, production
standard
4x2, 4x4H,
6x2-2, 6x4,
6x6H
L - LX All variants Exhaust with raised endpipe 5
Bodywork limitations
possibleE.g.: crane behind
cab or swap body tractor unit/
solo truck
6x2/2,
6x2/4,
6x2-4
4x4,
6x4-4,
6x6
TRUCKNOLOGY
Diagonally above the frame upper edge,
M cab ESC-721
Longitudinally on the frame,
M cab ESC-723
Diagonally above the frame upper edge,
L-XXL cabs ESC-722
Longitudinally on the frame,
L-XXL cabs ESC-724
Direction of travel Direction of travel
Variant 1
Fig. 52: Fig. 53:
Variant 2
Fig. 54: Fig. 55:
TRUCKNOLOGY
Longitudinally above the frame upper edge,
M cab, left-hand side mounted exhaust,
production standard ESC-725
Longitudinally above the frame,
right-hand side mounted exhaust,
M cab ESC-727
Longitudinally above the frame upper edge,
M cab, raised exhaust endpipe ESC-726
Longitudinally above the frame, raised exhaust
endpipe, M cab ESC-728
Variant 3
Fig. 56: Fig. 57:
Variant 4
Fig. 58: Fig. 59:
TRUCKNOLOGY
L-XXL cab, raised exhaust endpipe ESC-729
L-LX cab, diagonally above the frame up-
per edge rotated through 180, right-hand
side mounted exhaust ESC-730
L-LX cab, diagonally above the frame upper edge
rotated through 180, raised exhaust endpipe ESC-731
Direction of travel
Variant 5
Fig. 60:
Variant 6
Fig. 61: Fig. 62:
TRUCKNOLOGY
Dosing module
The position of the dosing module may not be changed.
Extending the pipe between the dosing module and the pump module is possible up to an overall length of 3,000 mm.
Extending/shortening the AdBlue
and engine coolant pipes.

Extensions for repositioning the AdBlue
tank or the combi tank can be achieved by procuring the longest pipe harness or one that
matches the installation. These can be procured from the MAN spare parts service. Harnesses may be shortened by trimming the pipe
bundle to length at the interface to the AdBlue
pump module. Alternatively, the harness may be looped so it covers a longer distance.
Under no circumstances may the pipes from the tank to the pump module be longer than 6,000 mm.
Generally only pipe-to-pipe unions with pipe connectors manufactured by VOSS are permitted (can be sourced e.g. from
the MAN spare parts department).
Inserting the pipe connector is only permitted using a special tool from Voss (crimping pliers MAN no.80.99625.0023).
In order to minimise pressure losses a maximum of only one extension is permissible for each corresponding
coolant/AdBlue
feed or return pipe.

Fig. 63: Pipe connector (VOSS) for extending/shortening the AdBlue
and coolant pipes ESC-423

For pressing the AdBlue
pipes on the plastic plug only pre-tted plastic plugs with 1,000 mm of pipe from VOSS
are permitted (can be sourced e.g. from the MAN spare parts department).
It is imperative to avoid kinking the lines.
It is imperative that the lines are isolated against cold in the same way as original lines are protected.
TRUCKNOLOGY
X
View X
Pipe 3
Pipe 1
Pipe 2
Pipe 4
Pipe 1: Heating pipe - feed
Pipe 2: Heating pipe - return
Pipe 3: AdBlue

return line
Pipe 4: AdBlue

feed line
Pipe identier

Fig. 64: AdBlue
pipe identier (size 8.8 x 1.4; material PA-PUR, printed in yellow, pipe colour black) ESC-428
Fig 65: Engine coolant pipe identier (size 9 x 1.5; PA12-PHL-Y, printed in white, pipe colour black) ESC-429
Fig. 66: View of a pipe bundle showing coolant and AdBlue
pipes ESC-430
TRUCKNOLOGY
Dosing module Injection nozzle
AdBlue
intake line
Dosing line
AdBlue
runback line
Compressed-air line
Air supply
AdBlue

Tank
Combinend
delivery dosing
module
Injection
nozzle
Fig. 67: Temperature sensor, injection nozzle, dosing module ESC-424
For Euro 6 vehicles the following applies in addition to the lower emission standard requirements:
In contrast to Euro 5 vehicles the Euro 6 AdBlue
system is arranged as follows:

Fig. 68: Schematic overview of the AdBlue
system in Euro 6 vehicles ESC-419a

TRUCKNOLOGY
The pump module and the dosing module have been combined into a single unit.
There are currently two installation positions dependent upon the cab:
Fig. 69: Position on M cab ESC-740
Fig. 70: Position on L, LX, XL, XLX, XXL cabs ESC-741
Drawings showing measurements can be made available on request.
TRUCKNOLOGY
Moving the pump module or the AdBlue
tank is currently not possible.

If the standard AdBlue
tank is replaced with a container of greater or smaller capacity, then the vehicle must be re-parameterised.
Only those AdBlue
tanks may be installed that are available as a factory option for the relevant vehicle. In addition to the tank,
all other components of the AdBlue
system must be adapted correspondingly.

Additional cut-off valves in the AdBlue
pipes are inadmissible. Plug-in connections on the ends of the pipes may only be replaced with
plug-in connections that are approved by the factory. (Part numbers can be obtained from the spare parts service). The pipes may not
be kinked or compressed. The pipe cross section may not be modied under any circumstances.
The AdBlue
pipes must be protected against the airstream. The insulation tted at the factory may not be removed or modied.
The AdBlue
pipes must be protected against temperatures of over 50. The feed line of the heating circuit may not be bundled with the
other pipes.
4.12.4 Engine cooling
The cooling system (radiator, grille, air ducts, coolant circuit) may not be modied.
Exceptions only with the approval of MAN (for address see Publisher above).
Modications to the radiator that reduce the cooling surface cannot be approved.
The cooling system may be only be lled using coolants approved by MAN in accordance with the information given in
the service ll uid database.
Materials that contain copper may not be used in the cooling circuit.
Under following conditions, a radiator of modied performance may be required:
Operating primarily under stationary conditions
Operating in climatically unfavorable zones (areas with severe climates)
Operating in areas where it can be expected that the cooling performance may be reduced e.g. due to a high dust level
The nearest MAN sales centre can provide information on delivery options for the respective vehicle; for retrot installation, contact
the nearest MAN service centre or MAN authorised workshop. When tting a third-party radiator, the requirements set forth in
the installation guideline for installed engines must be observed. This guideline can be obtained from MAN (for address see Publisher
above).
TRUCKNOLOGY
4.12.5 Engine encapsulation, noise insulation
Work on and modications to factory-tted engine encapsulation are not permitted. If vehicles are dened as low-noise,
they will lose this status if retrot work has been carried out on them.
The company that has carried out the modication will then be responsible for re-obtaining the previous status.
4.13 Fitting other manual gearboxes, automatic transmissions and transfer boxes
Fitting manual or automatic transmissions that have not been documented by MAN is not possible because there is no interface to
the CAN powertrain. If non-documented manual or automatic transmissions are tted malfunctions may occur in safety-relevant
electronic systems. Fitting third-party transfer boxes (e.g. for use as power take-offs) impacts the powertrain electronics.
On vehicles tted with mechanical manual transmissions it may, under certain circumstances, be possible to adapt the system
by parameterisation. Consult MAN (for address see Publisher above) before any work is commenced.
It is not permitted to install these units to vehicles tted with MAN TipMatic / ZF ASTRONIC (ZF12AS transmissions).
5. Bodies
5.1 General
For identication purposes, each body must be tted with a model plate that must contain the following data as a minimum:
Full name of body manufacturer
Serial number.
The plates must have a minimum height of 4 mm.
The data must be marked permanently on the model plate.
Applicable standards regarding the securing of loads on commercial vehicles, in Europe EN 12640 (lashing points), 12641 (tarpaulins)
and 12642 (body structure) are to be observed, if requested compliance with these standards must be ensured, e.g. by adding a relevant
clause to the purchase contract. Bodies have a signicant inuence on the vehicles handling characteristics and drag, and consequently
also on fuel consumption. Bodies must therefore not unnecessarily increase drag or negatively affect the vehicles handling
characteristics. The unavoidable bending and twisting of the frame should not cause any undesirable characteristics in either the body
or the vehicle. The body and chassis must be able to absorb such forces safely. The approximate value for permissible bending can be
calculated as follows:
Formula 16: Approximate value for permissible bending

i

1
l
i
+ l
f =
200
TRUCKNOLOGY
Where:
f = Maximum bending, in [mm]
l
i
= Wheelbases, l
i
= sum of the wheelbases, in [mm]
l
= Frame overhang, in [mm]

The body should transfer as few vibrations as possible to the chassis. We assume that bodybuilders should at the very least be able to
determine approximate ratings for the subframe and assembly. It is also expected that suitable measures are taken to prevent vehicle
overloading. The unavoidable tolerances and hystereses arising in vehicle design must also be taken into consideration.
These include, for example:
the tyres
the springs (including hysteresis in air suspension systems)
the frame
When the vehicle is in operation, other dimensional changes will occur. These include:
settling of the springs
tyre deformation
body deformation.
The frame must not be deformed before or during installation. Before positioning the vehicle for installation, it should be driven
backwards and forwards a few times to release any trapped stresses. This applies particularly to vehicles tted with more than 2 axles
due to the axle stiffness that occurs when cornering. The vehicle should be placed on a level surface to install the body. Frame height
differences on the left/right of 1.5% of the ground-to- frame upper edge distance are within the limits of the hysteresis and settling
effects outlined above. The body must be able to sustain such differences which should not be compensated by frame alignment, spring
inserts or by adjusting the air suspension level because these will inevitably change during operation. Variations > 1.5% must be notied,
before any repairs are carried out, to the MAN customer services department which will decide which measures are to be taken by the
bodybuilder and/or the MAN service centre. Accessibility, Clearances: Access to the ller necks for AdBlue
fuel and further service ll

uids using petrol pump nozzle must be ensured, by corresponding body cut-outs, if required. This applies in particular to bodies without
a subframe and to bodies with low substructure height.
Accessibility to any components attached to the frame (e.g. spare wheel lift, battery box) must not be impeded by the body.
The freedom of movement of moving parts in relation to the body must not be adversely affected.
For example:
Brake cylinders
Gearchange mechanism (gear linkage, cable-controlled gearshift)
Axle mounting components
Intarder pipework
To ensure minimum clearances the following should be taken into account:
Maximum compression of the springs
Dynamic compression during the journey
Compression when starting off or braking
Side tilt when cornering
Operation with anti-skid chains
Limp-home mode characteristics, for example damage to an air spring bellows during a journey and the resulting side tilt
(e.g. 3 side tilt to ISO 1726 on tractor units see also the Coupling devices TG booklet).
Despite wheel guards it is still possible for dirt, stones, sand etc., to be thrown up against the body, particularly during off-road use.
Body structures must therefore be suitably protected (e.g. by tting protective grilles or applying a resistant coating).
TRUCKNOLOGY
5.1.1 Machinery Directive (2006/42/EC)
The Machinery Directive can be obtained from EUR-Lex at the following link:
http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=OJ:L:2006:157:0024:0086:DE:PDF
or
http://eur-lex.europa.eu
General
The Machinery Directive serves to ensure the health and safety of persons, in particular of employees, consumers and objects,
in particular in relation to the risks inherent whilst using machinery.
It sets forth generally applicable, fundamental health and safety protection requirements in accordance with the state of the art at
the time of design, together with technical and commercial requirements that are supplemented by a range of specic requirements for
certain classes of machine.
There is an appropriate procedure for every type of machine with which compliance with the underlying health and safety protection
requirements can be checked. These include the conformity assessment procedures, the CE conformity markings and a risk
assessment. Furthermore, the manufacturer must prepare technical documentation for each machine.
Scope of application
In addition to the Guide to Fitting Bodies, bodybuilders must also observe the Machinery Directive. The Machinery Directive is
fundamentally not applicable to the trucks chassis because the applicable statutory requirements are dened in the Directive
on type-approval of motor vehicles and their trailers (70/156/EEC).
The Machinery Directive does however, apply to a range of bodies.
The products (truck bodies) that fall under this scope of application are dened in Article 1 of the Machinery Directive
(scope of application).
The Machinery Directive applies fundamentally to:
Machines
Interchangeable equipment
Safety-related components
Load suspension devices
Chains, ropes and straps
Removable driveshafts
Incomplete machines
Examples include:
Loading cranes
Liftgates (tail-lifts)
Tipper bodies
Flushing and suction bodies
Recovery platform bodies
Compressors tted to the body
Mechanically driven cable winches
Roll-off and set-down skip loader bodies
Aerial work platforms
Tanker bodies
TRUCKNOLOGY
Among others, exceptions include:
Agricultural and forestry tractor units
Vehicles and vehicle trailers (70/156/EWG)
If such a product (body/mounted equipment) is mounted onto the truck chassis, then the Machinery Directive applies not to the truck
chassis, but to the body that is mounted upon it. The Machinery Directive also applies to the interfaces between the truck chassis and
the body that are responsible for the safe movement and operation of the machine. This is why it is necessary to differentiate between
self-propelled agricultural machines (which fall fully under the Machinery Directive) and truck chassis with bodywork that includes or
is mounted with machinery.
Examples of self-propelled agricultural machines include:
Self-propelled construction machines
Concrete pumps
Mobile cranes
Gully emptiers
Drilling rig carrier vehicles
Denition of machinery in accordance with 2006/42/EC
an assembly, tted with or intended to be tted with a drive system other than directly applied human or animal effort, consisting of
linked parts or components, at least one of which moves, and which are joined together for a specic application;
an assembly referred to in the rst indent, missing only the components to connect it on site or to sources of energy and motion;
an assembly referred to in the rst and second indents, ready to be installed and able to function as it stands only if mounted on
a means of transport, or installed in a building or a structure;
assemblies of machinery referred to in the rst, second and third indents or partly completed machinery referred to in point (g) which,
in order to achieve the same end, are arranged and controlled so that they function as an integral whole;
an assembly of linked parts or components, at least one of which moves and which are joined together, intended for lifting loads and
whose only power source is directly applied human effort;
Source: Excerpt from 2006/42/EC
TRUCKNOLOGY
5.1.2 CE marking (CE conformity marking in accordance with 2006/42/EC)
The bodybuilder shall ensure that the superstructure, along with its attachments and accessories, complies with the statutory
requirements. The Machinery Directive (2006/42/EC) sets forth the types of machinery that require CE marking.
The following apply fundamentally to the superstructure:
All machinery must carry the CE mark. I.e. this includes all safety-relevant components, removable driveshafts, chains, cables and straps.
Incomplete machines may not carry a CE mark.
For the CE marking of machinery, the following applies:
The CE marking shall be afxed to the machinery visibly, legibly and indelibly.
The afxing on machinery of markings, signs and inscriptions that are likely to mislead third parties as to the meaning or form
of the CE marking, or both, shall be prohibited.
Any other marking may be afxed to the machinery provided that the visibility, legibility and meaning of the CE marking is
not thereby impaired.
In order to ensure the same quality for the CE marking and the manufacturers mark, it is important that they be afxed
according to the same techniques. In order to avoid confusion between any CE markings which might appear on certain
components and the CE marking corresponding to the machinery, it is important that the latter marking be afxed alongside
the name of the person who has taken responsibility for it, namely the manufacturer or his authorised representative.
It is prohibited to pre-date or post-date the date of manufacture of the machinery when afxing the CE marking.
If the CE marking is reduced or enlarged the proportions shown in the drawing reproduced here must be maintained.
The various components of the CE marking must have approximately the same vertical dimensions, which may not be
less than 5 mm. The minimum dimension may be waived for small-scale machinery.
The CE conformity marking shall consist of the initials CE taking the following form:
Where machinery is also the subject of other Directives relating to other aspects and providing for the afxing of the CE marking,
the marking shall indicate that the machinery also conforms to the provisions of those other Directives. However, where one or more
of those Directives allow the manufacturer or his authorised representative to choose, during a transitional period, the system to
be applied, the CE marking shall indicate conformity only to the provisions of those Directives applied by the manufacturer or his
authorised representative. Particulars of the Directives applied, as published in the Ofcial Journal of the European Union,
shall be given on the EC declaration of conformity. Where the full quality assurance procedure referred to in Article 12(3)(c)
and 12(4)(b) has been applied, the CE marking must be followed by the identication number of the notied body.
TRUCKNOLOGY
5.1.3 Afxing the hazardous goods marker board to the front panel
In order to avoid damage to the front ap through afxing the hazardous goods marker board the board should be tted in accordance
with the Service Information SI Number: 288606 Hazardous Goods Marker Board.
This is available from MAN specialist workshops.
Fig. 71: Correct position of the hazardous goods marker board on the front panel ESC-485
TRUCKNOLOGY
Surface and corrosion protection affects the service life and appearance of the product. In general, the quality of the coatings on body
components should be equal to that of the chassis.
To ensure this requirement is met, the MAN Works Standard M 3297 Corrosion protection and coating systems for non-MAN bodies
is binding for bodies that are ordered by MAN. If the customer commissions the body, this standard becomes a recommendation only.
Should the standard not be observed, MAN provides no guarantee for any consequences.
MAN-works standards may be obtained from www.normen.man-nutzfahrzeuge.de (registration required).
Series production MAN chassis are coated with environmentally friendly, water-based 2-component chassis top-coat paints at
approx. 80C. To guarantee uniform coating, the following coating structure is required for all metal component assemblies on the body
and subframe and, following frame modications, on the chassis:
Bare metal or blasted component surface (SA 2.5)
Primer coat: 2-component epoxy primer, or if possible cathodic dip painting to MAN works standard M 3078-2,
with zinc phosphate pre-treatment
Top coat: 2-component top-coat paint to MAN works standard M 3094, preferably water-based; if there are no facilities
for this, then solvent-based paint is also permitted (www.normen.man-nutzfahrzeuge.de, registration required).
Instead of a primer and top coat, the substructure of the body (e.g. longitudinal members, cross members and corner plates)
galvanising may also be used. See the relevant data sheets from the paint manufacturer for information on tolerances for drying
and curing times and temperatures. When selecting and combining different metals (e.g. aluminium and steel) the effect of the
electrochemical series on the occurrence of corrosion at the boundary surfaces must be taken into consideration (insulation).
The compatibility of materials must also be taken into consideration.
After all work on the chassis has been completed:
Remove any drilling swarf
Remove burrs from the edges
Apply wax preservative to any cavities.
Mechanical connections (e.g. bolts, nuts, washers, pins) that have not been painted over must be given optimum corrosion
Protection.
To prevent salt corrosion whilst the vehicle is stationary during the body-building phase all chassis must be washed with clean water
to remove any salt residues as soon as they arrive at the body manufacturer.
5.3 Subframes
5.3.1 General
Should a subframe be required it must be of a continuous design, it may not be interrupted or bent out to the side
(exceptions e.g. for some types of tipper, require approval).
No moving parts may be restricted in their freedom of movement by the subframe structure.
5.3.2 Permissible materials, yield points
The yield point, also called elongation limit or
0,2
limit, must not be exceeded under any driving or load conditions.
The safety coefcients must be taken into account. See table 24 for the yield points for different subframe materials.
TRUCKNOLOGY

2
B

3
B
H
B
Table 24: Subframe materials (examples), standard designations and yield points
Material
number
Material
designation old
Old standard
0,2
N/mm
2
B
N/mm
2
Material
designation new
New standard Suitability for use in
TGS/TGX subframe
1.0037 St37-2 DIN 17100 235 340-470 S235JR DIN EN 10025 Not permitted
1.0570 St52-3 DIN 17100 355 490-630 S355J2G3 DIN EN 10025 Well suited
1.0971 QStE260N SEW 092 260 370-490 S260NC DIN EN 10149-3 Not permitted
1.0974 QStE340TM SEW 092 340 420-540 Withdrawn Not for point loads
1.0976 N/A N/A 355 430-550 S355MC DIN EN 10149-2 Well suited
1.0978 QStE380TM SEW 092 380 450-590 Withdrawn DIN EN 10149-2 Well suited
1.0980 QStE420TM SEW 092 420 480-620 S420MC DIN EN 10149-2 Well suited
1.0984 QStE500TM SEW 092 500 550-700 S500MC DIN EN 10149-2 Well suited
Materials S235JR (St37-2) and S260NC (QStE260N) are not approved for TGS/TGX subframes.
5.3.3 Subframe design
The external width of the subframe must be the same as that of the chassis frame and must follow the exterior lines of the main frame.
The longitudinal members of the subframe must lie at on the upper ange of the frame longitudinal member.
As far as possible the subframe should be designed to be exible. The usual chamfered u-proles used in vehicle construction are
the best in terms of complying with the requirement for torsional exibility.
Rolled sections are not permitted. If a subframe is closed at various points to form a box, the transition from the box to the u-prole
must be gradual. The length over which the transition from the closed to the open section occurs must be at least triple the width of
the subframe (see Fig. 72).
Fig. 72: Transition from box to u-prole ESC-043
Where possible arrange the subframe cross member above the position of the frame cross member.
When tting the subframe the main frame connections must not be detached.
A B
TRUCKNOLOGY
Detail A Detail B
Mounting holes
Recess 40
Avoid diagoal welds at the frame bends
Provide cross-
members at the
bends in the frame
All drillings on the subframe-frame-
cross-member connection drilled
to 14,5 and reamed to 16 + 0,3
On each side, the middle bolt that sup-
ports the frame connection must be left
in place
If the subframe is shorter
than the frame round-off
here R = 0,5 subframe
thickness
Fig. 73: Subframe design ESC-096
The subframe longitudinal member must reach as far forward as possible at least beyond the rearmost front spring hanger.
For an air-sprung 1
st
axle we recommend a clearance of 600mm between the wheel centre of the 1
st
axle and the subframe.
875.0002
< a
a
0
,
2
.
.
.
0
.
3
h

3
0

t

h

t

r
=
2
t
h

0
,
6
.
.
0
,
7
h

3
0

TRUCKNOLOGY

Subframe extends to above
rearmost front spring hanger
Fig. 74: Distance of subframe from the middle of the 1st axle ESC-497
In order to comply with the required dimensions the subframe must follow the contours of the frame.
It may be tapered or recessed at the front (see Figs 75 to 78 for examples).
Fig. 75: Subframe taper at front ESC-030 Fig.76: Subframe recess at front ESC-031
Fig.77: Subframe - adapting by widening ESC-098 Fig. 78: Subframe - adapting by tapering ESC-099
TRUCKNOLOGY

Flexible shims such as rubber or
similar products are not permitted
5.3.4 Attaching subframes and bodies
Load transmission from the superstructure to the subframe in particular the attachment of the superstructure to the vehicle frame and
the corresponding connections are the responsibility of the body manufacturer. Subframes and chassis frames are to be connected
using either a exible or a rigid connection. Depending on the particular situation, it may be necessary to use both types of subframe to
vehicle attachment at the same time (this is then referred to as semi-rigid where the length and area of the rigid connection are stated).
The mounting brackets provided by MAN are intended for the exible installation of loading platforms and box bodies.
This does not mean that they are unsuitable for other add-ons and bodies. However, a check must be made to see whether they are
strong enough when equipment and machines requiring drives, lifting equipment, tanker bodies etc. are installed. Wooden or exible
shims between the frame and the subframe or the frame and the body are not permitted (see Fig. 79).
Reasoned exceptions are permitted only if MAN can issue written approval.
(For address see Publisher above).
Fig. 79: Flexible shims ESC-026
5.3.5 Screw connections and riveted joints
Screw connections with a minimum strength class of 10.9 and mechanical locking device are permitted, for screw connections see
Section 4.3 in this booklet. It is also possible to use high-strength rivets (e.g. Huck
-BOM, blind fasteners) manufacturers installation

instructions must be followed. The riveted joint must be at least equivalent to the screw connection in terms of design and strength.
In principle although never tested by MAN it is also possible to use ange bolts. MAN draws your attention to the fact that such
ange bolts place considerable requirements on installation accuracy because they have no locking device as such.
This applies particularly when the grip length is short.

Fig. 80: Riveted joint for open and closed proles ESC-157
1200
TRUCKNOLOGY

Mounting bracket on frame Mounting bracket on subframe
5.3.6 Flexible connection
Flexible connections are non-positive/frictional connections. Relative movement between frame and subframe is possible to a limited
degree. All bodies or subframes that are bolted to the vehicle frame by means of mounting brackets are exible connections.
Even when shear plates are used, these connecting pieces should be regarded as exible if they do not comply with the requirements
of a rigid connection (see Section 5.3.7 below) exible connections the mounting points located on the chassis must be used rst.
If these are not sufcient or cannot be used for design reasons, then additional mountings are to be located at suitable points.
If additional frame holes are required adhere to requirements stated in Section 4.3.
The number of mountings should be selected to ensure that the distance between the mounting point centres does not exceed
1,200 mm (see Fig. 81).
Fig. 81: Distance between subframe mountings ESC-400
If MAN mounting brackets are supplied, either tted to the vehicle or as loose components, the bodybuilder is still under obligation
to check whether their number and location (existing holes in frame) is correct and adequate for the particular body installation.
The mounting brackets on MAN vehicles have oblong holes that run in the longitudinal direction of the vehicle (see Fig. 82).
They compensate for any tolerances and for exible connections permit the unavoidable longitudinal movement between
the frame and the subframe or between the frame and the body. To balance out the width clearances, the subframe mounting brackets
may also have oblong holes and these must be arranged at right angles to the longitudinal direction of the vehicle.
Fig. 82: Mounting brackets with oblong holes ESC-038
The mounting brackets on the frame are ush with the frame upper edge (allowable tolerance of 1mm). Any gaps between the mounting
brackets may be compensated for by inserting steel shims of appropriate thickness (see Fig. 83). Avoid inserting more than four shims at
any one mounting point.
TRUCKNOLOGY

Compensate for variations in spacing with max. 4 shims, an air
gap of max. 1 mm is permissible.
Use spacer sleeves
with long bolts

2
5
Fig. 83: Shims between mounting brackets ESC-628
The bolted connection of the rst mounting bracket on the left and right is subject to high vertical loading. In order to allow increased
expansion length, long bolts ( 25 mm in length) with spacer sleeves for instance (see g. 90), must be tted to the front subframe
mountings in the case of subframes with exible attachments (not if there are three-point or diamond-shaped mountings) at the front
(see g. 84, section 5.4.2). The outer diameter of the spacer sleeves should equal the maximum width across the bolt head.
Fig. 84: Increasing elasticity by using longer bolts and spacer sleeves ESC-635
For other examples of exible mounting see Figs. 85 and 86.
TRUCKNOLOGY

Clamp - property class 8.8
Spacer - non elastic
Attached on frame web only
Angular or U-shaped bridging piece
Angle bracket, approx. 5 mm
thickness, tted
Fig. 85: Long bolts and cup springs ESC-101
Fig. 86: Shackle mounting ESC-123
TRUCKNOLOGY

5.3.7 Rigid connection
With rigid connections relative movement between the frame and subframe is no longer possible, the subframe follows all
the movements of the frame. If the connection is rigid the frame and the subframe prole in the vicinity of the rigid connection are
regarded as one single section for calculation purposes. Mounting brackets supplied ex-works and other connections that are
non-positive/frictional are not considered to be rigid connections. Only positive-locking connecting elements are rigid.
Positive-locking connecting elements are rivets or bolts. However, bolts are only classed rigid connectors if a hole tolerance of 0.2 mm
is maintained. If rigid connections are to be made using solid-shank bolts then the bolts thread may not come into contact with the bolt
hole walls (see Fig. 87). The minimum grade for bolts is 10.9.
Fig. 87: Contact of the bolt thread with the hole wall ESC-029
Due to the short grip lengths that are normally required, use may be made of spacer sleeves as shown in Fig. 88.
TRUCKNOLOGY

Subframe
Shear plate
Spacer sleeve
Frame
Thread must not touch
the hole wall of the
shear plate or of the
frame
Welds may only en-
croach into the radii of
the shear plates by a
max. of 45
Fig. 88: Fitting shear plates ESC-037, ESC-019
TRUCKNOLOGY

Fig. 89: Twin mounting with plug weld ESC-025
Single piece shear plates may be tted to each side of the frame. Individual shear plates are preferred however.
The thickness of the shear plate must be the same as the thickness of the frame web; a tolerance of +1 mm is permitted.
In order that the frames ability to twist is affected as little as possible, the shear plates are to be located only where absolutely
necessary. The beginning, end and the required length of a rigid connection can be determined by calculation.
The connection should be designed based on the calculation. Flexible mountings may be selected for the other mounting points outside
the dened rigid area.
TRUCKNOLOGY

5.4 Bodies
5.4.1 Testing of bodies
Testing of bodies and subsequent approval in writing at MAN (for address see Publisher above) is required when deviations have been
made from this Guide to Fitting Bodies and the deviation has been made for valid technical reasons.
For the calculations, two copies of body documentation that must be suitable for inspection are required.
This documentation must contain the following information in addition to a drawing of the body:
Identication of the deviations from the Guide to Fitting Bodies in all documentation!
Loads and their load application points:
- Loads applied by the body
- Axle load calculation
Special conditions of use:
Subframe:
- Material and cross-sectional data
- Dimensions
- Type of section
- Arrangement of cross members in the subframe
- Special features of the subframe design
- Cross-section modications
- Additional reinforcements
- Upsweeps, etc.
Means of connection:
- Positioning (in relation to the chassis)
- Type
- Size
- Number.
Photos, 3D pictures and perspective drawings may be used for purposes of clarity but they may not replace the binding documentation
set out above.
5.4.2 Platform and box bodies
To ensure even load distribution on the chassis a subframe is normally used.
Consideration should be given to wheel clearances as early as during the body design stage including the lowered position/chassis
position at full suspension compression. Additional clearance requirements for items such as anti-skid chains, vehicle body roll,
degree of axle articulation must also be taken into account. Hinged vehicle sides may not contact the road surface even when
the vehicle is in the lowered position or the chassis position is at full suspension compression.
The body must sit torsion free on the longitudinal frame members.
Closed bodies in particular, such as box bodies, are designed to be relatively torsionally stiff with respect to the chassis frame.
So that the desired twisting of the frame (for example when cornering) is not hindered by the body, the body xtures should be exible at
the front and rigid at the rear. This is particularly important if the vehicle is designed for off-road purposes. For this application,
we recommend a front body mount with a three-point or diamond-shaped mounting (see Fig. 90 for mounting principle).
TRUCKNOLOGY

Fig. 90: Mounting options for torsionally rigid bodies on exible chassis with three-point and diamond-shaped mountings ESC-158
5.4.3 Tail-lifts
Pre-requisites
Before installing a tail-lift (also called lifting platforms, loading platforms, liftgates), its compatibility with the vehicle design, the chassis
and the body must be checked.
The installation of a tail-lift affects:
Weight distribution
Body length
Bending of the frame
Subframe bending
Type of connection between frame and subframe, and
The on-board electrical system (battery, alternator, wiring).
The body manufacturer must:
Carry out an axle load calculation
Observe the stipulated minimum front axle load (see the General Chapter, Section 3.2 Minimum front axle load)
Avoid overloading the rear axles
If necessary shorten the body length and rear overhang or extend the wheelbase
Check stability
Design the subframe and the connections to the frame (exible, rigid) see the Section Subframe specication in this Chapter
Provide batteries of greater capacity (175 Ah but preferably 225 Ah) and an alternator of sufcient capacity (at least 28V 80 A,
but preferably 28V 110 A). These can be provided ex-works as optional equipment.
TRUCKNOLOGY

Install an electrical interface for the tail-lift (available ex-works as optional equipment; for wiring diagrams and pin assignment
see the Section on electrical connections).
Observe statutory regulations, e.g.:
- EC Machinery Directive (consolidated version of Directive 89/392/EEC: 98/37/EC)
- Accident prevention regulations
- Fit an underride guard
- Fit approved lighting installations in accordance with 76/756/EEC (in Germany, additional yellow indicator lights and
retroreective red-white warning markers are also required when operating the tail-lift, in accordance with 53b,
Paragraph 5, StVZO for lifting platforms).
Dening the sub-frame
The sub-frame tables are applicable subject to the following:
Minimum front axle load respected in accordance with Section 3.2 of the General Chapter
No design overload of the rear axle(s)
In addition to the support loads occurring on the tail-lift, both minimum front axle load and maximum rear axle load are to be
added to the trailer vehicle on testing.
Vehicles with lifting axles must lower the lifting axle during operation of the tail-lift.
Overhang limits in respect of max. vehicle overhang must be respected.
The values in the tables are the benchmark values for which, due to strength/deformation reasons, no outriggers are required.
They are only required if:
- The tail-lift loading capacity limits given in the tables is exceeded
- Outriggers are required for stability reasons
If outriggers although not required are tted, this does not affect the size of the extended sub-frame.
It is not permitted to raise the vehicle on the outriggers, as this could damage the frame.
The tables are sorted in ascending order according to tonnage class, variant description, suspension type and wheelbase, where the
vehicle designation (e.g. TGS 18.xxx 4x2 BB, TGX 26.xxx 6x2-2 BL) is to be regarded as an aid to orientation. The 3-digit type numbers,
also known as type code numbers, which appear at the 2
nd
and 4
th
positions of the basic vehicle number and at the 4
th
and 6
th

positions of the vehicle identication number are binding (for explanation, see the General Chapter).
All other technical documents, e.g. chassis drawings, assembly directives relate to the type number.
The overhang always related to the wheel centre of the last axle includes both the frame overhang of the
standard production chassis and the overall maximum vehicle overhang (including body and tail-lift, see Fig. 89 below),
which must not be exceeded when the tail-lift has been tted. If the specied maximum vehicle overhang is insufcient,
the sub-frame data in the following lines for which the -condition is satised applies (apart from the start of the rigid
connection, which relates only to the wheelbase).
The sub-frames in the tables are examples. For instance U120/60/6 is a U section open to the inside with an outer height of 120 mm,
top and bottom 60 mm wide and 6 mm thick over the entire cross section.
Other steel sections are acceptable if they have at least equivalent values in respect of the moment of inertia I
x
, moments of resistance
W
x1
W
x2
and yield point
0,2
.
TRUCKNOLOGY

Rigid area according to guidelines in Chapters
5.3.6 and 5.3.7
Flexible
Start from centre of
1
st
axle
Frame overhang
Max. vehicle
overhang
Table 25: Technical data for sub-frame prole
Prole Height Width Thickness I
x
W
x1
, W
x2
0,2
B
Mass
U100/50/5 100 mm 50 mm 5 mm 136 cm
4
27 cm
3
355 N/mm
2
520 N/mm
2
7,2 kg/m
U100/60/6 100 mm 60 mm 6 mm 182 cm
4
36 cm
3
355 N/mm
2
520 N/mm
2
9,4 kg/m
U120/60/6 120 mm 60 mm 6 mm 281 cm
4
47 cm
3
355 N/mm
2
520 N/mm
2
10,4 kg/m
U140/60/6 140 mm 60 mm 6 mm 406 cm
4
58 cm
3
355 N/mm
2
520 N/mm
2
11,3 kg/m
U160/60/6 160 mm 60 mm 6 mm 561 cm
4
70 m
3
355 N/mm
2
520 N/mm
2
12,3 kg/m
U160/70/7 160 mm 70 mm 7 mm 716 cm
4
90 cm
3
355 N/mm
2
520 N/mm
2
15,3 kg/m
U180/70/7 180 mm 70 mm 7 mm 951 cm
4
106 cm
3
355 N/mm
2
520 N/mm
2
16,3 kg/m
If adequate, the exible structure of the sub-frame is designated by a w. For the partially rigid structure (designated s),
the number of screw connections, the weld seam length in each case per frame side and the start of the rigid connection from
the centre of axle 1 are indicated (see Fig. 91). For the rigid and/or partially rigid connection, the conditions set out in Chapter 5.3.7
Bodies apply. In addition to the connecting elements listed in the table the installation guidelines of the tail-lift manufacturer must also be
observed when attaching the tail-lift attachment plates.
Fig. 91: Tail-lift installation: overhang dimension, dimensions with partially rigid connection ESC-433
TRUCKNOLOGY

Table 26: Subframe and mounting method
TGS/TGX 18.xxx Connection method: w = exible s = rigid
03S TGS/TGX 18.xxx 4x2 BB (leaf - leaf)
Wheel-
base
Standard
frame
overhang
max.
vehicle
overhang
LBW
useful
load
Min.
subframe
Type of
connection
Each frame side Start from
centre of
1
st
axle
Bolt diameter
16+0,2
Weld length
4.800 2.800 30,0 No subframe required
5.100 2.900 3.000 20,0 No subframe required
30,0 U 160/60/6 w
U 100/50/5 s 16 750 2.950
20,0 U 120/60/6 w
U 100/50/5 s 12 600 3.200
30,0 U 100/50/5 s 16 800 3.200
15,0 U 100/50/5 w
20,0 U 180/70/7 w
U 100/50/5 s 14 650 3.400
30,0 U 100/50/5 s 18 850 3.400
15,0 U 160/70/7 w
U 100/50/5 s 12 550 3.650
20,0 U 100/50/5 s 14 650 3.650
30,0 U 120/60/6 s 20 800 3.650
6.700 3.400 4.000 7,5 U 100/50/5 s 10 450 3.850
10,0 U 100/50/5 s 12 550 3.850
Caution: Overall length > 12 meter 15,0 U 100/50/5 s 14 650 3.850
20,0 U 100/50/5 s 16 750 3.850
30,0 U 140/60/6 s 24 950 3.850
05X 08S 13S 13X tractor units it is not permissible to convert these to trucks with tail-lifts
TRUCKNOLOGY

TGS/TGX 18.xxx Connection method: w = exible s = rigid
06S 06X 10S 10X 15S 15X TGS/TGX 18.xxx 4x2 BL / LL / LL-U (leaf - air / air - air / low build height air - air)
Wheel-
base
Standard
frame
overhang
max.
vehicle
overhang
LBW
useful
load
Min.
subframe
Type of
connection
centre of
1
st
axle
Bolt diameter
16+0,2
Weld length
4.200 2.350 30,0 No subframe required
30,0 U 120/60/6 w
U 100/50/5 s 16 700 2.600
30,0 U 180/70/7 w
U 100/50/5 s 16 750 2.750
20,0 U 120/60/6 w
U 100/50/5 s 12 550 2.950
30,0 U 100/50/5 s 16 750 2.950
15S 15X 15,0 U 100/50/5 w
20,0 U 180/70/7 w
U 100/50/5 s 14 550 3.050
30,0 U 100/50/5 s 18 800 3.050
15,0 U 160/60/6 w
U 100/50/5 s 12 600 3.200
20,0 U 100/50/5 s 14 700 3.200
30,0 U 120/60/6 s 20 800 3.200
10,0 U 120/60/6 w
U 100/50/5 s 10 450 3.400
15,0 U 180/70/7 w
U 100/50/5 s 12 550 3.400
20,0 U 100/50/5 s 14 650 3.400
30,0 U 120/60/6 s 20 750 3.400
6.300 3.700 3.750 7,5 U 120/60/6 w
U 100/50/5 s 10 400 3.650
10,0 U 160/70/7 w
U 100/50/5 s 10 450 3.650
15,0 U 100/50/5 s 12 550 3.650
20,0 U 100/50/5 s 14 650 3.650
30,0 U 140/60/6 s 20 800 3.650
6.700 3.400 4.000 10,0 U 100/50/5 s 12 550 3.850
15,0 U 120/60/6 s 16 600 3.850
30,0 U 160/70/7 s 24 800 3.850
TRUCKNOLOGY

TGS/TGX 24.xxx 6x2-2 Connection method: w = exible s = rigid
45S 45X TGS/TGX 24.xxx 6x2-2 LL-U (low build height air - air)
Wheel-
base
Standard
frame
overhang
max.
vehicle
overhang
LBW
useful
load
Min.
subframe
Type of
connection
centre of
1
st
axle
Bolt diameter
16+0,2
Weld length
+ 1.350 10,0 U 140/60/6 w
U 100/50/5 s 10 600 3.400
15,0 U 180/70/7 w
U 100/50/5 s 12 700 3.400
20,0 U 100/50/5 s 14 800 3.400
30,0 U 120/60/5 s 20 900 3.400
4.800 2.150 2.650 7,5 U 160/60/6 w
+ 1.350 U 100/50/5 s 10 550 3.550
10,0 U 180/70/7 w
U 100/50/5 s 12 600 3.550
15,0 U 100/50/5 s 14 750 3.550
20,0 U 100/50/5 s 16 850 3.550
30,0 U 140/60/6 s 22 1.000 3.550
TRUCKNOLOGY

TGS/TGX 26.xxx 6x2 Connection method: w = exible s = rigid

18S 18X 21S 21X TGS/TGX 26.xxx 6x2-2, 6x2-4 BL / LL (leaf - air / air - air)
Wheel-
base
Standard
frame
overhang
max.
vehicle
overhang
LBW
useful
load
Min.
subframe
Type of
connection
centre of
1
st
axle
Bolt diameter
16+0,2
Weld length
+ 1.350 30,0 U 120/60/6 w
U 100/50/5 s 14 750 3.050
+ 1.350 30,0 U 180/70/7 w
U 100/50/5 s 14 800 3.200
+ 1.350 15,0 U 120/60/6 w
U 100/50/5 s 12 600 3.400
20,0 U 180/70/7 w
U 100/50/5 s 14 700 3.400
30,0 U 100/50/5 s 16 850 3.400
+ 1.350 10,0 U 120/60/6 w
U 100/50/5 s 10 550 3.550
15,0 U 180/70/7 w
U 100/50/5 s 12 650 3.550
20,0 U 100/50/5 s 14 700 3.550
30,0 U 120/60/6 s 18 850 3.550
5.100 2.800 2.900 7,5 U 160/60/6 w
+ 1.350 U 100/50/5 s 10 500 3.700
10,0 U 180/70/7 w
U 100/50/5 s 10 550 3.700
15,0 U 100/50/5 s 12 650 3.700
20,0 U 100/50/5 s 14 750 3.700
30,0 U 120/60/6 s 20 850 3.700
5.500 3.100 3.200 7,5 U 100/50/5 s 10 550 3.950
+ 1.350 10,0 U 100/50/5 s 12 650 3.950
15,0 U 100/50/5 s 14 700 3.950
20,0 U 120/60/6 s 16 750 3.950
30,0 U 160/60/6 s 22 950 3.950
5.900 2.900 3.500 7,5 U 100/50/5 s 12 650 4.200
+ 1.350 10,0 U 120/60/6 s 14 650 4.200
20,0 U 160/60/6 s 20 850 4.200
30,0 U 180/70/7 s 26 950 4.200
Measurements in mm, loads in kN
TRUCKNOLOGY

Disconnect standard plug connector
and connect the cab-tail-lift cable
harness in between!
Legende
A100 255 Central electrics box
A302 352 Central computer 2
A358 Control unit tail-lift
A403 339 Vehicle management computer
A407 342 Instrumentation
F219 118 Tail-lift fuse (pin 15)
H254 Tail-lift warning lamp
K175 281 Starter interlock relay
K467 281 Tail-lift relay
S286 547 Tail-lift switch
X669 Plug connector, starter interlock
X744 Plug connector, tail-lift
X2541 246 Potential distributor 21 pin, lead 31000
X2542 246 Potential distributor 21 pin, lead 58000
X3186 Plug connector, tail-lift
Leads 91003, 91336, 91556, 91557, 91572 and 91573
lead to a 7 pin connector housing on the frame end
(rolled up).
Electrical connection
Electro-hydraulic tail-lifts require most careful design of their electrical supply. It is assumed that the information contained in the Chapter
Electrics, electronics, cables, of the Guide to Fitting Bodies is applied. Ideally, the electrical interface for the tail-lift should be supplied
ex-works (package comprises switches, warning lights, starter inhibitor and power supply for tail-lift). Retrotting is a complex procedure
and requires intervention in the vehicles power supply, which may only be carried out by correspondingly qualied MAN service staff.
The factory-tted transport securing device must be removed. The body manufacturer must check the circuitry of the tail-lift for its
compatibility with MAN vehicles. Under normal circumstances triggering of interface A358 may only be effected with 24 V continuous
signals not with ash pulses. In case of failure a clocked signal may be applied briey to relay K476.
For the tail-lift electric interface see the additional wiring diagram below.
Fig. 92: Additional wiring diagram, tail-lift for MAN no. 81.99192.1920
TRUCKNOLOGY

Anti-wear prole
Frame
5.4.4 Interchangeable containers
MAN swap body ttings: The TGS/TGX range includes fully air-sprung vehicles that can be supplied ex-factory with swap body ttings.
Installation dimensions and centring devices correspond to the requirements of EN 284. There is a dedicated module in MANTED

where CAD drawings of the MAN swap body ttings can be viewed.
Container and interchangeable platforms that meet the requirements of EN 248 may be tted to the vehicles stated above.
The standard swap body ttings cannot however be freely utilised if different bodies that do not meet the requirements of EN 248 are to
be mounted. The relocation of support points or different dimensions are only permitted if they have been approved at MAN (for address,
see Publisher above). Do not remove the centre supports their use is imperative!
The body must lie along their whole length. If this is not possible for design reasons, then an adequately dimensioned subframe must be
tted. Supports for interchangeable containers are not suitable for absorbing forces that are exerted by mounted machinery and point
loads. This means that when, for example, tting concrete mixers, tippers, fth-wheel subframes with fth-wheel couplings, etc, different
xtures and supports must be used.
The body manufacturer must provide evidence that they are suitable for this purpose.
Other interchangeable equipment: Interchangeable containers should lie on the upper side of the frame, along the whole length of the
frame. A subframe can be omitted if the requirements in the following Section 5.4.5 Self-supporting bodies without subframe are met.
Frame longitudinal members must however, be protected from wear (e.g. by tting an anti-wear prole as shown in Fig. 93).
Materials with a yield point of
0,2
350 N/mm may be used for the anti-wear prole, but not for the subframe. The anti-wear prole may
assume the functions of a subframe only if it can be demonstrated by calculation that it is suitable for this purpose.
Fig. 93: Anti-wear prole for interchangeable container ESC-121

6
0
0

TRUCKNOLOGY

Exaggerated representation of linear
contact between two U-sections
Subframe Linear contact
Frame
5.4.5 Self-supporting bodies without subframe
A subframe may possibly not be required if the following conditions are met:
There is a sufcient moment of resistance (affects the bending stress), and
There is a sufcient geometrical moment of inertia (affects exing) and
and there is a self-supporting body.
The prerequisite for vehicles that require a subframe in accordance with the above guideline is written approval from MAN (for address
see Publisher above).
Note on tting bodies without subframes:
The distances between the body cross members must not be above 600 mm (see Fig. 94).
This distance of 600mm may be exceeded only in the area of the rear axles.
Fig. 94: Distances between cross members if no subframe is tted ESC-001
The minimum lengths of the supports on the frame must be calculated according to the rules of Hertzian contact stresses.
For this application, it is assumed that there is linear contact between two cylinders rather than linear contact between a cylinder and
a at surface. Fig. 95 illustrates an exaggerated deformation of two U-sections placed one on top of the other.
An example of the calculation can be found in Chapter 9 Calculations.
Fig. 95: Deformation of two U-sections ESC-120
TRUCKNOLOGY

Vibration problems cannot be ruled out on bodies not tted with subframes. MAN cannot make any statements on the vibration
behaviour of vehicles tted with bodies that have no subframes, since the vibration behaviour depends on the body.
If inadmissible vibrations develop, the cause must be eliminated, which may mean that a subframe has to be retrotted after all.
Even on designs without subframe, access to the ller necks for fuel and other operating uids (z.B. AdBlue
) must be ensured as
must access to all other frame components ( e.g. spare wheel lift, battery box).
The freedom of movement of moving parts in relation to the body must not be adversely affected.
5.4.6 Single-pivot body
The single-pivot body, which is comparable with a fth-wheel coupling, always requires a subframe. Positioning of the pivot point for
the single-pivot body behind the theoretical rear axle centreline must be approved with regard to axle load distribution and handling.
In this case approval must be granted by MAN (for address see Publisher above).
5.4.7 Tank and container bodies
Depending on the type of goods being transported, the responsible party must ensure that the vehicles are equipped in accordance
with national requirements, guidelines and regulations. In Germany, the technical inspection organisations (DEKRA, TV) can provide
information regarding the transportation of hazardous goods (subject to the Hazardous Goods Regulations). Tank and container bodies
generally require a continuous subframe as described in Chapter 5.3 Subframes.
The conditions for approved exceptions for tanker and container bodies without subframes are listed below.
The front connection between the body and chassis must be designed so that it does not hinder the frames ability to twist.
This can be achieved using front mountings that are as exible as possible, e.g.:
Pendulum-type mounting (Fig. 96)
Flexible mounting (Fig. 97)
Fig. 96: Front mounting of pendulum type ESC-103 Fig. 97: Front mounting of exible type ESC-104
The front mounting point should be as close as possible to the front axle centreline. (see Fig. 98).
The rear, laterally stiff body support must be tted in the vicinity of the theoretical rear axle centreline. At this point the connection to
the frame should also be of sufcient size. The distance between the theoretical rear axle centreline and the centre of the support must
be <1,000 mm (see Fig. 98). See Section 3.5. Theoretical axle centreline.
1400
l
t
1000
500
TRUCKNOLOGY

Centre of support if possible the same as the theoretical rear axle centreline
and not > 1,000 mm away from it
Design the connection such that it affects frame twisting to
the least possible extent
Fig. 98: Layout of tanker and bulk container mountings ESC-404
Once the body has been installed it is important that a test is carried out to conrm whether vibrations or other disadvantageous handling
characteristics are evident. Vibration can be inuenced by correct subframe design and the correct layout of the tank mountings.
Tank and container bodies without subframe: Tanker and container bodies without subframes can be approved if the conditions described
here are observed and there are double or triple tank mountings on each side of the frame.
All supports must be arranged at the specied distances. If the permissible range is exceeded, this may cause the frame to bend
excessively, which is not permitted. The vehicle may only be used on metalled roads.
Once the body has been tted it is important that a test is carried out to check for vibrations or other disadvantageous handling
characteristics.
TRUCKNOLOGY

Table 27: Chassis without subframes for tanker bodies with double and triple mountings
Model Wheel formula Suspension Wheelbase
05S 4x2
4x4H
Leaf-air 3.600-4.500
06S
22S
22X
10S Full air
10X
18S 6x2-2
6x2-4
6x4H-2
6x4H-4
6x2-4
Leaf-air 3.900-4.500
+ 1.350
18X, HV1
35S
35X
74S
89S
89X
21S Full air
21X
42S 6x2/2
6x2/4
6x4H/2
6x4H/4
Leaf-air 2.600-4.150
+ 1.350
42X
4x2/2
6x2-4
6x2/2
700 1100 700 1400 700
800
1000 1200
1200
1200
1000 500
1000 1200 1200
1000 500
1000 500 500
TRUCKNOLOGY

Double mounting Triple mounting
Theoretical rear centreline Theoretical rear centreline
Theoretical rear centreline Theoretical rear centreline
Fig. 99: Requirements for tank mountings for designs without subframes ESC-411
5.4.8 Tippers
If repairs are to be carried out beneath the tipped superstructure of vehicles tted with tipping bodies, the bodybuilder must provide
supports to ensure their employees occupational safety.
Tipper bodies require a chassis designed for their special purpose. MAN has special tipper chassis in its product range.
These may be selected in MANTED
by querying the system by body type.

Factory-built tipper chassis require no additional work if it is ensured that the following points are observed:
The permissible gross weight
The permissible axle loads
The standard tipper body length
The standard frame overhang
The standard vehicle overhang
The maximum tipping angle of 50 to the rear or side
All tipper bodies require a continuous steel subframe. (For information on the minimum yield point and suitable materials see Section
5.3.2 in this booklet).
The body manufacturer is responsible for the connection between the chassis and the subframe.
Tipper rams and tipper mountings must be incorporated into the subframe because the vehicle frame is not designed to take point loads.
The following parameters must be observed:
Tipping angle to the rear or side 50
During tipping to the rear, the centre of gravity of the tipper body with payload should not move behind the centreline of
the last axle unless stability of the vehicle is guaranteed.
S

5
0
o

a

b
TRUCKNOLOGY

The centre of gravity of the tipper body
must not move behind the centreline of the last axle unless
the vehicle is sufcientls stable
We recommend:
During the tipping operation, the height of the centre of gravity of the tipper body should not be exceeded.
(Dimension a see g. 100 1.800).
The rear tipper mounting should be located as close as possible to the theoretical rear axle centreline.
Recommendation: The distance b (see table 28 and g. 100) between the centre of the tipper mountings and theoretical
rear axle centreline (1100 mm-1250 mm) should not be exceeded (theoretical rear axle centreline see Section 3.5).
Table 28: Tippers: Maximum values for centre of gravity height and tipper mounting spacing
Chassis Dimension a [mm] Dimension b [mm]
Two axle vehicle 4x2, 4x4H u. 4x4 1.800 1.100
Three axle vehicle x2, 6x4, 6x4H u. 6x6 2.000 1.250
Four axle vehicle 8x2, 8x4, 8x4H, 8x6, 8x6H u. 8x8 2.000 1.250
Fig. 100: Tippers: Maximum values for centre of gravity height and tipper mounting spacing ESC-405
For operational safety reasons, operational conditions or when the above stated recommendations are exceeded, further measures
may become necessary, such as the use of hydraulic outriggers to increase stability or the relocation of specic equipment.
It is however assumed that the bodybuilder recognises the requirement for such measures since they are intrinsically dependent upon
the design of his product.
To improve stability and operational safety, rear tippers are sometimes required to be tted with a so-called scissors-action support
and/or a support at the end of the frame (see Fig. 101).
TRUCKNOLOGY

Fig. 101: Rear tipper with scissors-action support and rear support ESC-406
To improve stability on vehicles with air suspension it must be ensured that the air suspension is lowered before commencing the tipping
operation. Lowering can either be done manually via the ECAS control unit or it can be automatic using special equipment Code 311PH
(input of the ECAS parameters for air suspension lowering to 20mm above the buffers). Special equipment 311PH automatically lowers
the vehicle to the dened level above the buffers if the power take-off is engaged when the vehicle is at a standstill. To ensure that the
function provided by Code 311PH is properly activated it is imperative that the correct order of operations is observed when engaging
the power take-off (see operating instructions). A check must also be carried out to ensure that the message No ride height appears on
the display and that the vehicle has actually lowered. If an automatic lowering system is not tted then the user/driver must be informed
of the requirement to manually lower the air suspension.
The following applies in addition to Euro 6 vehicles:
On these vehicles it is absolutely essential that spacers are tted on the right side. Otherwise the components will contact the exhaust
silencer when then the drop-side panels open.
5.4.9 Set-down, sliding set-down and sliding roll-off tippers
For these types of body, the design often means that the subframes cannot follow the contour of the main frame and special
connections to the main frame must therefore be provided. The body manufacturer must ensure that these xtures are adequately
sized and are properly located. Information regarding proven xtures together with their design and tting is available in the body ma-
nufacturers installation instructions. MAN mounting brackets are available for tting loading platforms and box bodies.
They are not suitable for tting set-down, sliding set-down and sliding roll-off tipper bodies.
Because of the low substructure heights, the freedom of movement of all moving parts attached to the chassis (e.g. brake cylinders,
transmission shift components, axle guide components, etc) and the body (e.g. hydraulic cylinders, pipes, tipper frame, etc.) must be
checked and ensured. If necessary an intermediate frame must be tted. Additional measures may include limiting the suspension
travel and restricting the pendulum movement of the tandem axle. These must be approved by MAN (for address see Publisher above).
When loading and unloading, outriggers are required at the end of the vehicle if:
The rear axle load is more than twice the technically permissible rear axle load. Here, the tyre and rim load capacity must
also be taken into account.
The front axle loses contact with the ground. For safety reasons, lifting of this kind is strictly forbidden!
The stability of the vehicle is not guaranteed. This can result from a high centre of gravity height, an inadmissible side tilt
when suspension compression occurs on one side, if the vehicle has sunk into soft ground on one side etc.
Rear support by locking the vehicle springs is permitted only if MAN (for address see Publisher above) has approved the installation
together with the respective load transmissions. The required evidence of stability is to be provided by the body manufacturer.
TRUCKNOLOGY

To improve stability on vehicles with air suspension it must be ensured that the air suspension is lowered before commencing
the tipping operation. Lowering can either be done manually via the ECAS control unit or it can be automatic using special equipment
Code 311PH (input of the ECAS parameters for air suspension lowering to 20mm above the buffers). Special equipment 311PH
automatically lowers the vehicle to the dened level above the buffers if the power take-off is engaged when the vehicle is at
a standstill. To ensure that the function provided by Code 311PH is properly activated it is imperative that the correct order
of operations is observed when engaging the power take-off (see operating instructions). A check must also be carried out to ensure
that the message No ride height appears on the display and that the vehicle has actually lowered. If an automatic lowering system
is not tted then the user/driver must be informed of the requirement to manually lower the air suspension.
5.4.10 Propping air-sprung vehicles
The following must always be observed when propping leaf/air or fully air-sprung vehicles:
The manufacturer of the body is responsible for the stability of the overall system when in working operation.
To improve stability on vehicles with air suspension it must be ensured that the air suspension is lowered before commencing
the tipping operation. Lowering can either be done manually via the ECAS control unit or it can be automatic using special equipment
Code 311PE (input of the ECAS parameters for crane operation). Special equipment 311PE automatically lowers the vehicle onto
the buffers if the power take-off is engaged when the vehicle is at a standstill. Once the lowering operation has nished the system
maintains a dened residual pressure in order to protect the air-suspension bellows. To ensure that the function provided by Code
311PE is properly activated it is imperative that the correct order of operations is observed when engaging the power take-off
(see operating instructions). A check must also be carried out to ensure that the message No ride height appears on the display
and that the vehicle has actually lowered. If an automatic lowering system is not tted then the user/driver must be informed of
the requirement to manually lower the air suspension.
Although the complete raising of the axles provides the optimum stability within physical limits, the load that results puts a greater strain
on frames and subframes frames. Completely raising the axles as well as lowering the vehicle without special equipment Code 311PE
will result in damage to the air-suspension bellows.
In order to comply with the specications set forth in the guidelines and to minimise foreseeable misuse/risks, tting special equipment
Code 311PE is strongly recommended. Exceptions are possible in the case of special purpose vehicles/body designs but this shall be
under the bodybuilders sole responsibility and in agreement with the customer.
Note:
The functions provided by Codes 311PE / 311PH are deactivated when the engine / power take-off or similar is turned on or off and
the standard control laws of the ECAS system activated (setting the air-suspension to ride height). In cases where the vehicle is
required to remain for a long period at a set level (lowered position of the air-suspension) it may be necessary to completely suppress
the controlling function of the ECAS air-suspension system.
Should this be necessary, suppression of the controlling function can be achieved using special equipment 311PK (input of the ECAS
parameters with auxiliary circuit for suppressing the automatic levelling suspension system). If this is not already tted to the vehicle it
can be retrotted by a MAN service outlet (for further details see MAN Service Information 239704a).
We explicitly point out that this measure does not contribute to stability and is therefore not a means of extending the technical limits
of body-mounted equipment (e.g. cranes). The ECAS controlling function may only be suppressed during working operation.
a
G
Kr
G
H
b
TRUCKNOLOGY

5.4.11 Loading cranes
Empty weight and the total moment of a loading crane must be matched to the chassis on which it will be tted.
The basis for the calculation is the maximum total moment and not the lifting moment. The total moment is the result of the empty weight
and the lifting force of the loading crane with the crane arm extended. For calculation of the loading crane total moment see
formula 17 below:
Fig. 102: Moments on the loading crane ESC-040
Formula 17: Total moment of loading crane
g s (G
Kr
a + G
H
b)
M
Kr
=
1000
Where:
a = Distance of the crane centre of gravity from the centre of the crane pillar in [m], with the crane arm extended
to maximum length
b = Distance of the maximum lifting load from the centre of the crane pillar in [m], with the crane arm extended
to maximum length
G
H
= Lifting load of the loading crane in [kg]
G
Kr
= Weight of the loading crane in [kg]
M
Kr
= Total moment in [kNm]
s = Impact coefcient from details provided by the crane manufacturer (dependent on the crane control system),
always 1
g = Acceleration due to gravity 9,81 [m/s]
TRUCKNOLOGY

The number of outriggers (two or four) and their positions and distance apart is to be determined by the crane manufacturer on
the basis of the stability calculation and vehicle load.
For technical reasons, MAN may insist that four outriggers are tted.
When the crane is operating, the outriggers must always be extended and level with the ground. They must be repositioned accordingly
for both loading and unloading. Hydraulic compensation between the outriggers must be blocked.
The crane manufacturer must also detail any ballast that is required for ensuring stability.
Amongst other characteristics, the torsional stiffness of the entire frame connection is responsible for the stability.
It must be noted that a high torsional stiffness of the frame connection will necessarily reduce the ride comfort and the off-road
capability of the vehicles. The body builder or crane manufacturer is responsible for ensuring that the crane and subframe are properly
attached. Operating forces including their safety coefcients must be safely absorbed.
Mounting brackets available ex-works are not suitable for this purpose. Avoid inadmissible (over)loading of the axle(s).
The maximum permissible axle loading during crane operation must not be more than twice the technically permissible axle load.
The impact coefcients provided by the crane manufacturer must be taken into consideration (see Formula 17)!
The permissible axle loads must not be exceeded during vehicle operation, therefore an application-specic axle load calculation is
essential.
Asymmetric installation of a crane is not permissible if uneven wheel loads arise as a result (permissible wheel load difference 5%,
see also Chapter 3.1). The body builder must ensure adequate compensation.
The pivoting range of the crane must be limited if this is required to maintain the permissible axle loads or stability.
Methods for ensuring this compliance are the responsibility of the loading crane manufacturer (e.g. by limiting the lifting load dependent
on the pivoting range). During installation and operation of the loading crane, the required freedom of movement of all moving parts
must be observed. Controls must have the minimum freedom of movement as required by law. Unlike other bodies the minimum load
on the front axle(s) for crane bodies in any load state must be 30% for two-axle vehicles or 25% for three and four-axle vehicles in order
to maintain steerability. For a detailed denition see Section 3.2 in this booklet.
Any nose weights exerted on the trailer coupling must be taken into consideration in the required axle load calculation.
On vehicles with lifting axles, the weight ratios must also be checked with the trailing axle lifted. If necessary, the lifting option must
be disabled (see also Rear loading crane later in this Chapter).

Depending on the size of the crane (weight and centre of gravity position) and location (behind the cab or at the rear), vehicles must
be tted with reinforced springs, reinforced anti-roll bars or reinforced shock absorbers, if these items are available.
These measures will prevent the chassis from adopting a lopsided position (e.g. due to reduced compression of the reinforced springs)
and will prevent or reduce any tendency to roll.
However, with crane superstructures, it is not always possible to prevent the chassis from standing lopsided because of the shift
in the vehicles centre of gravity.
After installation of the body, adjustments or checks may have to be made on the vehicle. This applies particularly to the headlights and
the rear underride guard and the sideguards. Approval for a crane superstructure is necessary if the requirements stipulated in
this Guide to Fitting Bodies are exceeded.
This is the case if:
The permissible total crane moment as stipulated in Fig. 106 is exceeded
Four outriggers are tted
Front outriggers are tted.
TRUCKNOLOGY

Intermediate frame
Different forces come into play when four outriggers are tted. This means that MAN (for address see Publisher above) must always be
consulted. To guarantee stability whilst the crane is operating, the subframe in the area between the two
outrigger members must have sufcient torsional stiffness.
For strength reasons, lifting the vehicle on the outriggers is permissible only if the subframe structure absorbs all the forces resulting
from the operation of the crane and provided its connection to the chassis frame is not rigid (e.g. mobile cranes).
According to the applicable national regulations, the crane body and its operation must, before rst use, be inspected by a crane expert
from the technical inspection organisations or by a person authorised to inspect cranes.
Loading crane behind the cab:
If chassis components protrude above the upper edge of the subframe an additional intermediate frame needs to be provided on
the subframe (see Fig. 103). This can be designed so that it serves as a reinforcement for the subframe.
Fig. 103: Clearance for loading crane behind the cab ESC-407
It must still be possible for the cab to tilt and it must be possible to operate the locking mechanism unhindered at any time.
There must be no obstructions that encroach on the arc described by the cab when tilting. The tilt radii of the cabs are given in
the chassis drawings (these can be obtained from MANTED
www.manted.de).
Even when the permissible front axle load is observed, care still needs to be taken to prevent excessive top-heaviness of the vehicle
for handling reasons. A reduction of the front axle load, for example, can be achieved by relocating equipment.
On some vehicles, the permissible front axle load can be increased if the required technical conditions exist.
See Chapter 3, General technical basics for information on and procedures for increasing the permissible front axle load.
Rear loading crane:
In order to create the required space for the loading crane and achieve a more favourable front axle loading the spare wheel, normally
located at the rear, can be moved to a position on the side of the frame.
Stronger springs, a stronger anti-roll bar and other available stabilisation aids from MAN must be installed depending on the size of the
crane and the axle load distribution. This will prevent the vehicle from standing lopsided and reduce its tendency to roll.
When a lifting trailing axle is lifted, the front axle of the vehicle experiences a considerable lightening of the load. Because of the point
load acting dynamically on the end of the frame as a result of the crane, it is likely that the driving characteristics will not be sufciently
stable. Therefore, the lifting facility must be disabled if more than 80% of the permissible drive axle load is reached when travelling
unladen with the crane and with the axle lifted. It must also be disabled if the minimum front axle load (30% of the actual vehicle weight
of the now two axle vehicle) is not reached.
L
TRUCKNOLOGY

For manoeuvring purposes the trailing axle can be relieved if the subframe and body are of adequate size (moving-off aid).
The higher bending and torsional forces acting on the body and the frame structure must then be taken into account. If a centre axle
trailer is to be towed then the trailer nose weight must be taken into account during the chassis design stage.
Most importantly, the front axle loads must not be allowed to drop below the values stated in Section 3.2. Minimum front axle loads.
Detachable rear loading cranes:
The centre of gravity of the payload will change depending on whether the crane is attached or not. To achieve the largest possible
payload without exceeding the permissible axle loads, we recommend that the centre of gravity of the payload with and without
the crane be marked clearly on the body.
The larger overhang resulting from the installation of the coupling device must be taken into consideration.
It is the responsibility of the body manufacturer to ensure that the coupling mounting bracket is of adequate strength and that
the bracket support is properly tted to the vehicle. Forklifts carried on the vehicle are to be treated as attachable loading cranes when
being transported.
A second trailer coupling is to be installed on the mounting brackets for detachable rear loading cranes if the vehicle is to be operated
with a trailer. This trailer coupling must be connected to the one installed on the vehicle by means of a towing eye (see Fig. 104).
Note the instructions in Section 4.8 Coupling devices.
The coupling device and the body must be able to safely absorb and transmit forces arising during trailer operation.
If the crane is attached but the vehicle is being operated without a trailer, an underride guard must be tted to the coupling device t
ogether with the lighting installation as required by law.
Fig. 104: Coupling device for rear loading cranes ESC-023
1,5 b
R
b
R

TRUCKNOLOGY

Subframe for loading crane:
All loading crane bodies require a subframe. Even in the case of crane total moments that theoretically produce a required geometrical
moment of inertia of below 175cm
4
, a subframe with a geometrical moment of inertia of at least 175cm
4
must be tted.
To protect the subframe we recommend tting an additional upper ange (anti-wear plate) to prevent the base of the crane from wearing
into the subframe.
The thickness of the upper ange should be 8-10 mm depending on the size of the crane.
Loading cranes are frequently installed with various types of body, for which a subframe is also required (e.g. on tippers, tractor units,
single-pivot bodies). In this case, depending upon the body and its loading, a larger subframe suitable for the entire body structure
must be used.
The subframe for a detachable loading crane must be designed to ensure that the coupling device and the loading crane can
be supported safely. The body manufacturer is responsible for the design of the mounting bracket (bolt xings, etc.).
When installing a loading crane behind the cab the subframe must be enclosed to form a box, at least in the area surrounding the crane.
If the loading crane is installed at the rear, a closed section prole must be used from the end of the frame to at least a point forward
of the front-most rear axle location element.
In addition, to increase the torsional stiffness of the subframe, a cross-strut (X-shaped connecting piece, see Fig. 105) or
an equivalent structure must be tted.
To be recognised by MAN as an equivalent structure, it is a pre-requisite that MAN (for address see Publisher above) has issued an
approval.
Fig. 105: Cross-strut in the subframe ESC-024
The method of calculating and the correlation between crane total moment and geometrical moment of inertia dependent upon the
chassis frame applies equally to crane structures with two outriggers located behind the cab or on the frame end.
Safety coefcients have already been taken into account. The crane total moment M
Kr
however, must be factored into the calculation
along with the impact coefcient supplied by the crane manufacturer (see also formula 17 above).
The graph for crane total moment and geometrical moment of inertia is reproduced for the frame sections of the TGS/TGX models here
(see Fig. 107 below). No cranes may be mounted on chassis/tractor units with frame prole number 34 (model codes as at 08/2007:
08S, 49S).
The graphs in Fig. 104 only apply to cranes with double outriggers. They apply equally to crane structures located behind the cab or on
the frame end. Safety coefcients have already been taken into account. The crane total moment M
Kr
however, must be factored into the
calculation along with the impact coefcient supplied by the crane manufacturer (see also the formula Total moment of loading crane
further above in Chapter 5.4.10)
If body conditions (e.g. low container vehicles, breakdown trucks, etc.) mean that the design methods described here cannot be adhered
to, the entire body must be approved by MAN (for address see Publisher above).
TRUCKNOLOGY

Example of how to use the graphs in Fig. 103:
A subframe is to be specied for a TGS 18.xxx 4x2 BB, model 03S vehicle, frame section number 31. The vehicle is to be tted with a
crane with a total moment of 160 kNm.
Solution:
A minimum geometrical moment of inertia of approx. 1,250 cm
4
is derived from Fig. 107.
If one U-section with a width of 80 mm and a thickness of 8mm is formed into a box with an 8 mm thick section, a section height of at
least 170 mm is required, see diagram in Fig. 108. If two U-sections of a width/thickness of 80/8 mm are formed into a box, the minimum
height is reduced to approx. 140 mm, see Fig. 109.
If, when the values are read off, the section size in question is not available, round up to the next available size; rounding down
is not permitted.
The freedom of movement of all moving parts is not taken into consideration here; it must therefore be re-checked when
the dimensions have been selected.
An open U-section, as in Fig. 107, must not be used in the area around the crane. It is only shown here because the diagram can also
be used for other bodies.
2
0
0
4
0
0
6
0
0
8
0
0
1
0
0
0
1
2
0
0
1
4
0
0
1
6
0
0
1
8
0
0
2
0
0
0
2
2
0
0
2
4
0
0
2
6
0
0
2
8
0
0
3
0
0
0
2
2
0
2
0
0
1
8
0
1
6
0
1
4
0
1
2
0
1
0
0
8
0
TRUCKNOLOGY

C r a n e t o t a l m o m e n t [ k N m ]
S
u
b
f
r
a
m
e

g
e
o
m
e
t
r
i
c
a
l

m
o
m
e
n
t

o
f

i
n
e
r
t
i
a

l
x

[

c
m
4

]
P
r
o

l
e

N
o

3
1

&

4
3
:

U

2
7
0
/
8
5
/
8
P
r
o

l
e

N
o

3
2

&

4
5
:

U

2
7
0
/
8
5
/
9
,
5
Fig. 106: Crane total moment and geometrical moment of inertia for TGS/TGX ESC-516a
2
8
0

2
6
0

2
4
0

2
2
0

2
0
0

1
8
0

1
6
0

1
4
0

1
2
0

1
0
0

8
0

0

2
0
0

4
0
0

6
0
0

8
0
0

1
0
0
0

1
2
0
0

1
4
0
0

2
0
0
0

1
8
0
0

1
6
0
0

2
2
0
0

2
4
0
0

2
6
0
0

2
8
0
0

3
2
0
0

3
0
0
0

3
4
0
0

1

U
8
0
.
.
.
2
2
0
/
6
0
/
6

2

U
8
0
.
.
.
2
8
0
/
6
0
/
7

3

U
8
0
.
.
.
2
2
0
/
7
0
/
6

4

U
8
0
.
.
.
2
8
0
/
7
0
/
7

5

U
8
0
.
.
.
2
8
0
/
7
0
/
8

6

U
8
0
.
.
.
2
2
0
/
8
0
/
6

7

U
8
0
.
.
.
2
8
0
/
8
0
/
7

8

U
8
0
.
.
.
2
8
0
/
8
0
/
8

2

4

7

5

8

1

3

H
t
B

S

6

TRUCKNOLOGY

S e c t i o n h e i g h t i n [ m m ]
G
e
o
m
e
t
r
i
c
a
l

m
o
m
e
n
t

o
f

i
n
e
r
t
i
a

[

c
m
4

]
O
p
e
n

U
-
s
e
c
t
i
o
n
Fig. 107: Geometrical moment of inertia for U-sections ESC-213
2
8
0

2
6
0

2
4
0

2
2
0

2
0
0

1
8
0

1
6
0

1
4
0

1
2
0

1
0
0

8
0

0

2
0
0

4
0
0

6
0
0

8
0
0

1
0
0
0

1
2
0
0

1
4
0
0

2
0
0
0

1
8
0
0

1
6
0
0

2
2
0
0

2
4
0
0

2
6
0
0

2
8
0
0

3
2
0
0

3
0
0
0

3
4
0
0

3
6
0
0

3
8
0
0

4
0
0
0

4
2
0
0

4
4
0
0

4
6
0
0

1

U
8
0
.
.
.
2
2
0
/
6
0
/
6

2

U
8
0
.
.
.
2
8
0
/
6
0
/
7

3

U
8
0
.
.
.
2
2
0
/
7
0
/
6

4

U
8
0
.
.
.
2
8
0
/
7
0
/
7

5

U
8
0
.
.
.
2
8
0
/
7
0
/
8

6

U
8
0
.
.
.
2
2
0
/
8
0
/
6

7

U
8
0
.
.
.
2
8
0
/
8
0
/
7

8

U
8
0
.
.
.
2
8
0
/
8
0
/
8

H
t
B

t

2

4

7

5

8

1

6

3

TRUCKNOLOGY

G
e
o
m
e
t
r
i
c
a
l

m
o
m
e
n
t

o
f

i
n
e
r
t
i
a

[

c
m
4

]
U
-
s
e
c
t
i
o
n

c
l
o
s
e
d
T
G
M
T
G
S
Fig. 108: Geometrical moment of inertia for open U-sections ESC-214
2
8
0
2
6
0
2
4
0
2
2
0
2
0
0
1
8
0
1
6
0
1
4
0
1
2
0
1
0
0
8
00
2
0
0
6
0
0
1
0
0
0
1
4
0
0
1
8
0
0
2
2
0
0
2
6
0
0
3
0
0
0
3
4
0
0
3
8
0
0
4
2
0
0
4
6
0
0
5
0
0
0
5
4
0
0
5
8
0
0
6
2
0
0
6
6
0
0
7
0
0
0
1
U
8
0
.
.
.
2
2
0
/
6
0
/
6
2
U
8
0
.
.
.
2
8
0
/
6
0
/
7
3
U
8
0
.
.
.
2
2
0
/
7
0
/
6
4
U
8
0
.
.
.
2
8
0
/
7
0
/
7
5
U
8
0
.
.
.
2
8
0
/
7
0
/
8
6
U
8
0
.
.
.
2
2
0
/
8
0
/
6
7
U
8
0
.
.
.
2
8
0
/
8
0
/
7
8
U
8
0
.
.
.
2
8
0
/
8
0
/
8
B
H
2
4
7
5
8
B
1
6
3
TRUCKNOLOGY

G
e
o
m
e
t
r
i
c
a
l

m
o
m
e
n
t

o
f

i
n
e
r
t
i
a

[

c
m
4

]
T
w
o

s
a
m
e

b
o
x
e
d

U
-
s
e
c
t
i
o
n
s
T
G
M
T
G
S
Fig. 109: Geometrical moment of inertia for boxed U-sections ESC-215
TRUCKNOLOGY

5.4.12 Cable winches
For installation of a cable winch the following points are important:
Pulling force
Installation location: Front, centre, rear, side installation
Type of drive: Mechanical, electromechanical, electrohydraulic.
Vehicle components such as axles, springs, frames, etc. must under no circumstances be overloaded by the operation of the cable
winch. This is particularly important if the direction of the winch towing force is not in line with the vehicle longitudinal axis. It may be
necessary to t an automatic pulling force limiter, a device that cuts-in depending upon the direction from which the pulling force is
applied. When a winch is installed at the front, its maximum pulling force is limited by the technically permissible front axle load. The
technically permissible front axle load is stated on the vehicles manufacturing plate and in the vehicle documentation.
A winch design that has pulling forces greater than the technically permissible front axle load may be tted only after prior consultation
with MAN (for address see Publisher above). Under all circumstances, care must be taken to ensure proper guidance of the cable.
The cable should feed through as few guide pulleys as possible. At the same time however, it must be ensured that the function of
vehicle parts is in no way adversely affected. A hydraulic winch drive is preferred because it offers better regulation and installation
options. The efciency of the hydraulic pump and motor is to be taken into account (see also the Chapter 9, Calculations).
A check should be made to see whether existing hydraulic pumps such as those on the loading crane or the tipper can be used.
This can sometimes avoid the need for installing several power take-offs.
The hydraulic circuit on vehicles tted with HydroDrive
is a closed circuit system. It may not be tapped to drive a cable winch.

On worm gears in mechanical winches, the permissible input speed must be observed (normally < 2,000 rpm).
The reduction ratio of the power take-off is to be selected accordingly. Take the low efciency of the worm gear into consideration when
calculating the minimum torque at the power take-off. Observe the instructions contained in the Chapter 6, Electrics, electronics wiring
for electromechanical and electrohydraulic winches.
5.4.13 Transport mixers
The MAN range includes chassis that are suitable for mounting a transport mixer body. These chassis can be recognised by
the additional sufx TM for Transport Mixer in the sales documentation. The chasis-side requirements and shear plates are included
with the vehicle.
In order to reduce the tendency to roll, transport mixer chassis must be tted with anti-roll bars on both rear axles and must be
equipped with springs that are specically tuned for the application.
The cement mixer body is generally driven by the ywheel-side power take-off (SSNA) at the engine. Further information on power
take-offs can be found in the separate Power take-offs booklet.
If a different chassis (e.g. a tipper chassis) is to be used for mounting a transport mixer it is assumed that the equipment of springs and
stabilizers of the axles and shear plate layout equivalent to that of a comparable transport mixer body is tted and that anti-roll bars for
both rear axles are tted
The shear plate arrangement of tipper chassis and the mounting brackets for loading platforms are not suitable for mounting transport
mixer bodies. Fig. 108 illustrates an example for the arrangement of shear plates on a transport mixer chassis.
The body is rigid along virtually its entire length, the only exception atng the front end of the subframe ahead of the drum mounting.
The rst two shear plates must be positioned in the area of the front mounting brackets for the drum. For a more detailed explanation
on subframe mountings see section 5.3.4 Attaching subframes and bodies. The shear plate thickness should be 8 mm and at least
match the material quality S355J2G3 (St52-3).
Concrete conveyor belts and concrete pumps cannot easily be tted onto standard concrete mixer chassis. In some circumstances, a
different subframe structure from that of the normal mixer subframe or a cross connection on the frame end is required (similar to rear
loading crane bodies, section 5.4.11, Subframes for loading cranes). Approval from MAN (for address see Publisher above) and from
the transport mixer manufacturer is essential.
300
1
3
0
4
5
TRUCKNOLOGY

Fig. 110: Transport mixer body ESC-016a
5.4.14 Car transporter
Car transporters are normally built on the basis of a two-axle tractor unit and have an interchangeable body.
The body is fastened to the tractor unit using releasable connections at the front, the fth-wheel coupling at the rear and additional
connectors. The transmission of loads from the body to the chassis, in particular the fastening of the body and the associated
connections, are always the responsibility of the bodybuilder.
The basic tractor unit shall be equipped as follows in order that the vehicle can be used as a car transporter:
(The equipment specications listed below relate solely to a tractor unit used as the basis vehicle.
Bodies mounted on truck chassis with a longer wheelbase are not discussed here):
- No approval for constructing car transporter body on 08S (TGS 18.xxx BLS-TS) and 13S/13X (TGS/TGX 18.xxx LLS-U)
- Maximum wheelbase 3,900 mm
- The four-point rear axle location system of the production standard tractor unit can be tted
(2nd generation cast version only for TGS/TGX) as can the level adjustment system for the tractor unit
(1 level adjustment system)
- It is imperative that a anti-roll bar is tted to the front axle
We strongly recommend equipping car transporters with ESP (available under code 307DT for types 06S and 10S)
- The vehicle type entered onto the ofcial papers must be Vehicle for interchangeable operation
(option to use as tractor unit and truck for car transport). This corresponds to use as a car transporter and no
parameterisation is required. Under no circumstances may a vehicle be reparameterised as a truck.
- The tractor unit end cross member with hole pattern for trailer coupling must be tted (no. 81.41250.0141).
Because of its greater thickness (9.5 mm) only this end cross member is suitable for supporting the forces exerted
by the rear body connection (never use 5 mm tractor unit end cross members).
In its so-called second life (after use as a car transporter) the vehicle can solely be used as a tractor unit but
not as a truck!
TRUCKNOLOGY

6. Electrics, electronics, wiring
6.1 General
The Chapter Electrics, electronics, wiring does not attempt to provide fully comprehensive information on all issues relating to
the vehicle electrical systems of modern commercial vehicles. Further information on individual systems can be found in the respective
repair manuals, which can be obtained from the spare parts service. The electrics, electronics and wiring installed in commercial vehicles
complies with the relevant applicable national and European standards and directives, which are to be regarded as minimum
requirements. MANs own standards often considerably exceed those minimum requirements of national and international standards.
As a result, many electronic systems have been adapted and expanded. In some situations, for reasons of quality or safety,
MAN stipulates the condition that MAN standards are used. This is stated in the corresponding sections. Body manufacturers can obtain
relevant MAN standards from www.normen.man-nutzfahrzeuge.de (registration required). There is no automatic updating and
replacement service.
6.2 Routing cables, earth cable
On MAN vehicles the frame is not misused as the earth cable; instead, a separate earth cable should be laid to the electric consumer
along with the positive lead. Common earth points to which the bodybuilder can connect earth cables are located:
In the central electrics compartment (rear, see g. 111)
Behind the instrumentation
On the rear right-hand engine mount.
For detailed instructions see section 6.5 additional power consumers, below.
No more than 10A (actual current consumption) in total may be drawn at the earth points behind the central electrics box and behind
the instrumentation. Cigarette lighters and any additional sockets have their own power limits, please refer to the respective instruction
manual.
The body builders negative cable may as a general rule be connected to the common earth points at the engine and under the following
conditions may be connected to the negative terminal of the batteries:
The vehicle is equipped with an earth cable between engine and frame (standard from January 2010 production).
The battery terminal has sufcient room for connection of the earth cable.
6.3 Handling batteries
6.3.1 Handling and maintaining batteries
The test and charging cycle in accordance with the charging log/ charging schedule applies (e.g. when the vehicle is not being used
whilst the body is being tted). Checking/charging the battery is to be carried out according to the charging log supplied with the vehicle
and is to be initialled.
Rapid charging or assist-starting equipment is not permitted for trickle charging since their use may damage control units.
Vehicle to vehicle assist-starting is permitted, provided the instructions in the operating manual are followed.
When the engine is running:
Do not switch off the battery main switch
Do not loosen or disconnect the battery terminals.
TRUCKNOLOGY

Caution!
Always follow this sequence when disconnecting the batteries and actuating the battery main switch:
Switch off all electric consumers (e.g. lights, hazard warning lights)
Switch off ignition
Close the doors
Wait for a period of 20 seconds before disconnecting the batteries (negative terminal rst)
The electric battery main switch requires an additional run-down time of 15 seconds.
Reason:
Many vehicle functions are controlled by the central on-board computer (ZBR) that must rst save its last status before it can be isolated.
If, for example, the doors remain open, it will be 5 minutes before the computer can stop operating, because the computer also monitors
the door-closing function. If the doors are open a waiting period of over 5 minutes is therefore necessary before the batteries can be
disconnected. Closing the doors will shorten this waiting time to 20 seconds.
If the above sequence is not followed some control units will inevitably have incorrect entries (e.g. the ZBR central on-board computer).
6.3.2 Handling and maintaining batteries with PAG technology
When original factory-tted batteries are exhausted MAN specialist workshops will only t maintenance free PAG technology batteries
(PAG = positive Ag, positive electrode with thin silver plating). These differ from conventional batteries through improved resistance to
deep-discharge damage, longer shelf-life and better charging rate. The conventional ller caps have been replaced by charge eyes.
The test and charging cycle in accordance with the charging log/charging schedule is monitored with the help of these charge eyes
which indicate the state of charge by the colour of the ball in the middle of the ller cap.
Caution!
The ller caps (charge eyes) of maintenance-free batteries must not be opened.
Table 29: Charge eye indications
Indication Battery condition Procedure
Green Correct electrolyte level, acid density above 1.21 g/cm
3
The battery is charged and in order.
Note check completed in the charging log
Black Correct electrolyte level, but acid density below 1.21 g/cm
3
The battery must be charged.
Note the recharge in the charging log
White Electrolyte level too low, acid density may lie above or below 1.21 g/cm
3
The battery must be replaced
A detailed Service Information, SI Number: Amendment 2, 114002 Battery is available from MAN specialist workshops.
TRUCKNOLOGY

6.4 Additional wiring diagrams and wiring harness drawings
Additional wiring diagrams and wiring harness drawings that contain or describe body ttings can be obtained from MAN (for address
see Publisher above). It is the responsibility of body manufacturer to ensure that the documents he uses,
for example wiring diagrams and wiring harness drawings, correspond with the current status of equipment tted to the vehicle.
Further technical information can be obtained from the repair manuals. These can be obtained from the spare parts service.
6.5 Fuses, additional power consumers
Do not modify or extend the vehicles electrical system! This applies to the central electrics box in particular.
Any damage resulting from modications will be the responsibility of those who carried out the modications.
The following points must be observed when retrotting additional electric consumers:
There are no spare fuses in the central electrics box for use by the body manufacturer. Additional fuses can be tted in a plastic holder
located in front of the central electrics box.
Do not tap into existing vehicle circuits or connect additional electric consumers to fuses that are already occupied.
Each circuit installed by the body manufacturer must be adequately rated and have its own fuses. The rating of the fuse should ensure
the protection of the wiring and not that of the system connected to it. Electrical systems must ensure adequate protection against all
possible faults, without affecting the vehicle electrics. Freedom from feedback must always be ensured.
When selecting the size of the wire cross-section, the voltage drop and the heating of the conductor must be taken into account.
Cross-sections below 1 mm
2
are to be avoided because their mechanical strength is not sufcient. Positive and negative wires must
have the same minimum cross-section.Current draw for 12V equipment must be effected only via a voltage converter. Power draw from
just one battery is not permitted because unequal charge statuses may cause the other battery to become overcharged and damaged.
Under certain circumstances, e.g. for equipment with a high power requirement (e.g. electrohydraulic tail-lifts) or in extreme climatic
conditions, higher capacity batteries will be required. In order to provide extra power, a larger capacity alternator is available ex-works.
If the body manufacturer installs larger batteries, the cross-section of the battery cable must be adapted to suit the new power draw.
If consumers are directly connected to terminal 15 (pin 94 in the central electrics box; see Fig. 111) it is possible that entries will be
logged in the error memories of control units as a result of a reverse ow of current into the vehicles electrical system. Consumers must
therefore, be connected in accordance with the following instructions.
Power supply terminal 15
Always t a relay that is triggered via terminal 15 (pin 94). The load must be connected through a circuit breaker at terminal 30 (pins
90-1, 90-2 and 91 at the rear of the central electrics box) (see Fig. 111). The maximum load must not exceed 10 amperes
For maximum loads of up to 10 amperes the load must be connected through a circuit breaker at terminal 30 (pins 90-1,
90-2 and 91, see Fig. 111 rear of the central electrics box).
For loads > 10 amperes connect through a circuit breaker directly at the batteries
Do not connect at the batteries, instead connect to the earth points inside (see Fig. 111 rear of the central electrics box)
and outside (rear left engine mounting) the cab.
TRUCKNOLOGY

Terminal 31
Terminal 30
Terminal 15
Terminal 31
for sensors
No cables are connected here as
standard. However, the pin may be used
as an additional connecting pin using
a bridge to pin 94 for terminal 15.
Fig. 111: Central electrics box, rear view ESC-720
TRUCKNOLOGY

Circuit breaker in accordance
with the rated current of the
additional consumer
(maximum 10 amperes)
Additional consumer
(rated current maxi-
mum 10 amperes)
Relay for voltage supply terminal 15
for the additional consumers
(e.g. 81.25902-0473).
Only connect voltage supply
terminal 15 to this terminal from
consumers that could also be
installed as standard (exception:
relay control for additional
consumers).
Wiring diagram, additional consumers
Key:
A1 00 central electrics box
F354 main circuit breaker terminal 30
F355 main circuit breaker terminal 30
F400 circuit breaker steering lock
F522 circuit breaker cable 30000
F523 circuit breaker cable 30000
G100 battery 1
G101 battery 2
G102 alternator
K171 relay terminal 15
M100 starter
Q101 ignition switch
X1 00 earth connection engine
X1 364 bridge between connector pins 90-1 and 90-2 of the central electrics box
X1 365 bridge between connector pins 90-2 and 91 of the central electrics box
X1 539
X1 557 plug connection cab connection point
X1 642 earth point in cab behind instrumentation
X1 644 earth point in cab next to the central electrics box
X1 913 bridge for cable 30076 in the cable conduit on the engine
TRUCKNOLOGY

6.6 Lighting installations
If the lighting system is modied, the partial operating permit to EU Directive 76/756/EEC, as amended by 97/28/EC is rendered void.
This is particularly true if the design of the lighting installation has been changed (number/size of lights) or if a light has been replaced
with a different light that is not approved by MAN. The bodybuilder is responsible for compliance with all statutory provisions.
It is particularly important that LED side marker lamps are not extended using other types of lamp as this will destroy the ZBR (central
on-board computer)!
The maximum allowable load applied to the lighting current paths must be observed.
Fitting higher rated fuses than the corresponding ratings in the central electrics box is nor permitted.
The following reference values should be taken as maximum values:
Table 30: Lighting current paths
Parking light 5A per side
Brake light 4x21 W solely lamps
Indicators 4x21 W solely lamps
Rear fog lamps 4x21 W solely lamps
Reversing light 5A total.
The term solely lamps refers to the fact that these current paths are monitored for errors by the central on-board computer and
that any errors will be displayed. The installation of LED lighting elements that are not approved by MAN is prohibited.
Note that on MAN vehicles an earth cable is used. Earthing to the frame is not permitted (see also Section 6.2, Routing cables,
earth cable).
After the body has been installed, the basic beam alignment of the headlights must be reset. This is to be carried out directly on the
headlamps, even if the vehicle is tted with headlight levelling control. This is necessary because altering the setting of the levelling
control does not adjust the basic beam alignment for the vehicle. Extensions or modications to the lighting system must be completed in
co-operation with the nearest MAN service centre using MAN-cats
because it may become necessary to re-parameterise the vehicles

electronics. See also Section 6.10.2.
6.7 Electromagnetic compatibility
Due to the interaction between the various electrical components, electronic systems, the vehicle itself and the environment,
the electromagnetic compatibility (EMC) must be tested. All systems tted to MAN commercial vehicles comply with the requirements
of MAN standard M 3285, available from www.normen.man-nutzfahrzeuge.de (registration required).
TRUCKNOLOGY

MAN vehicles comply with the requirements of EC Directive 72/245/EEC, including 95/54/EC and as amended by 2004/104/EU when
they leave the factory. All equipment (denition of equipment as in 89/336/EEC) that is installed in the vehicle by the body manufacturer
must meet the corresponding statutory regulations in force at the time.
The body manufacturer is responsible for the EMC of his components or systems.
After installing such systems or components, the body manufacturer remains responsible for ensuring that the vehicle still meets
the current legal requirements.
Freedom from feedback between the body-side electrics/electronics and those of the vehicle must be ensured, especially where
body-side interference could affect the operation of onboard units for road toll logging, telematics equipment, telecommunications
systems or other equipment tted to the vehicle.
6.8 Radio equipment and aerials
All equipment that is installed on the vehicle must comply with the current legal requirements.
All radio equipment (e.g. radio units, mobile telephones, navigation systems, onboard units for road toll logging etc.)
must be properly equipped with external aerials.

In this context properly means:
Radio equipment, e.g. radio control systems for remotely operating various vehicle body functions, must be installed such
that the functions of the commercial vehicle are not affected.
Existing cables must not be moved or used for additional purposes.
Use as a power supply is not permitted (the exception being approved MAN active aerials and their cables).
Access to other vehicle components for maintenance or repair must not be impaired.
Only drill into the roof at the locations provided for in the MAN design and only use installation components
(for example self-tapping sheet metal screws, seals) approved for this purpose.
MAN-approved aerials, wiring, cables, bushes and connectors can be obtained from the spare parts service
Annex I of EU-Council Directive 72/245/EEC, version 2004/104/EU, stipulates that possible installation positions for transmission
antennas, approved frequency bands and the transmit power must be published.
For the following frequency bands the proper tment at the mounting points stipulated by MAN (see Fig. 112)
on the cab roof is permitted.
Table 31: Frequency bands and the approved mounting position on the roof
Frequency band Frequency range max. transmit power
Short wave < 50 MHz 10 W
4 m band 66 MHz to 88 MHz 10 W
2 m band 144 MHz to 178 MHz 10 W
70 cm band 380 MHz to 480 MHz 10 W
GSM 900 880 MHz to 915 MHz 10 W
GSM 1800 1.710,2 MHz to 1.785 MHz 10 W
GSM 1900 1.850,2 MHz to 1.910 MHz 10 W
UMTS 1.920 MHz to 1.980 MHz 10 W
Position 2
Position 1
Position 3
Position 2
Position 1
Position 3
TRUCKNOLOGY

Description Item number Item For antennas see electrical parts list
Antenna installation 81.28200.8365 Pos. 1 Radio antenna
Antenna installation 81.28200.8367 Pos. 1 Radio antenna + D & E-Net
Antenna installation 81.28200.8369 Pos. 1 Radio antenna + D & E-Net + GPS
Installation of radio antenna LHD 81.28200.8370 Pos. 2 CB radio antenna
Installation of radio antenna RHD 81.28200.8371 Pos. 3
Installation of radio antenna LHD 81.28200.8372 Pos. 2 Trunked radio antenna
Installation of radio antenna RHD 81.28200.8373 Pos. 3
Einbau Funkantenne LL 81.28200.8374 Pos. 2 Trunked radio antenna 2 m band
Einbau Funkantenne RL 81.28200.8375 Pos. 3
Antenna installation LHD 81.28200.8377 Pos. 3 GSM and GPS antenna for the road toll
collection system
Antenna installation RHD 81.28200.8378 Pos. 2
Installation of radio antenna LHD 82.28200.8004 Pos. 2 CB and radio antenna
Installation of combi antenna RHD 81.28205.8005 Pos. 3 GSM + D & E-Net + GPS + CB radio
antenna
Installation of combi antenna LHD 81.28205.8004 Pos. 2
81.28240.0151
Tightening torque 6 NM
Transition resistance 1
81.28240.0151
Cross-section GSM & GPS antenna 81.28205.0080
High roof
Cross-section GSM & GPS antenna 81.28205.0080
sheet metal roofs
Schematic view
sheet metal roofs
L/R10;12;15;32;40
Schematic view
high roofs
L/R37;41;47
Cross-section Y=0
High roof
81.28200.8355
81.28200.8355
Cross-section Y=0
sheet metal roofs
Fig. 112: Antenna installation positions ESC-560
TRUCKNOLOGY

6.9 Interfaces on the vehicle, preparations for the body
No work is permitted on the vehicles electrical system other than via the interfaces provided by MAN (e.g. for tail-lifts, for start/stop
equipment, for intermediate speed regulation, FMS interface). Tapping into the CAN buses is prohibited except in the case of
the Body builder CAN bus see the control unit TG interface for external data exchange (KSM). The interfaces are described in detail in
the Interfaces TG booklet.
If the vehicle is ordered with body ttings (e.g. start/stop device on the end of the frame), these are already tted at the factory and partly
connected. The instrumentation is prepared in accordance with the order.
Before rst operation of the body ttings, the body manufacturer must ensure that valid, up-to-date versions of wiring diagrams and
wiring harness drawings are in use (see also Section 6.4).
Transport securing devices are tted by MAN (on the interfaces behind the front panel on the passenger side) for delivery of the vehicle
to the body manufacturer.
Before using each interface the transport securing devices must be properly removed.
The retrotting of interfaces and/or body ttings is often extremely complicated. It should not be attempted without enlisting the help of an
electronics specialist from the MAN service organisation.
Connecting to the D+ signal (engine running)
Caution: D+ may not be tapped from the alternator on TG vehicles.
In addition to the signals and information provided through the KSM interface it is also possible to tap into the D+ signal as follows:
The central on-board computer (ZBR) provides an Engine running signal (+24V).
This can be tapped into directly at the ZBR (socket F2 pin 17).
The maximum load on this connection may not exceed 1 Ampere. It should be noted that other internal consumers may also
be connected here. It must be ensured that this connection is free from feedback.
Remote transmission of data from the mass storage of digital tachographs and information contained on the driver card.
MAN supports the manufacturer-independent remote transmission of data from the mass storage of digital tachographs and information
contained on the driver card (RDL = remote download).
TRUCKNOLOGY

6.9.1 Electrical connections for tail-lifts
See Chapter Tail-lifts
6.9.2 Engine start-stop system
The engine start-stop system allows the vehicle engine to be started or stopped via a remote control or switch outside the cab.
The start-stop control is a system that works independently of the intermediate speed control interface and must be ordered separately.
There are various options available ex-works:
Engine start-stop system under the front panel (preparation)
Engine start-stop system on the engine
Engine start-stop system at the end of the frame (preparation)
If a variant does not exist or is not available as optional equipment for a vehicle, the engine start-stop system can be retrotted.
It must then be ensured that both the original MAN wiring harnesses and the documented connection options and locations are used.
It is also possible to incorporate the engine start-stop system via the CAN data bus. The requirement for this is that the customer-
specic control module (KSM) is installed in the vehicle at the factory. Further references, connection and signal descriptions can
be found in the separate guideline, TG Interfaces.
Specic parameterisation is not necessary for the engine start-stop system.
If the body manufacturer has installed the circuitry, the designation engine start-stop must be used.
This must not be confused with the term emergency stop.
6.9.3 Tapping into the speed signal
Caution! In order to avoid control unit error messages always switch off the ignition prior to carrying out any work on the tachograph!
It is possible to tap the speed signal from the tachograph. This will ensure that the load on the corresponding pin does not exceed 1 mA!
This is generally equates to the equivalent of two connected peripheral units. Should this option for tapping the signal be inadequate
then the following output multipliers bearing the MAN codes can be connected:
81.25311-0022 (3 * v-pulse output, max. load 1 mA for each output) or
88.27120-0003 (5 * v-pulse output, max. load 1 mA for each output).
Option for tapping the B7 signal = speed signal:
1) At connector B / Pin 7 or PIN 6 on the back of the tachograph
2) At the 3-pole plug connection X4366 / contact 1. The plug connection is located behind a cover on the driver side A-pillar
in the area around the drivers footwell.
3) At the 2-pole plug connection X4659 / contact 1 or 2. The plug connection is located behind the central electrical compartment
4) At the factory-tted interface with customer-specic control module from STEP1 (see the booklet TG electrical and
electronic interfaces, Chapter 4.3).
6.9.4 Tapping into the reverse gear signal
There are several options for tapping the reverse gear signal on vehicles in the TGS/TGX range. The reverse gear signal can be tapped
via the 2-pin connector X1627 at pin 1 or pin 2 of cable 71300. This is located in the central electrical compartment. It must be ensured
that the electrical load on the interface for the reverse gear signal does not exceed a permissible value of 100mA.
It is also possible to tap the reverse gear signal via the customer-specic module (KSM). The requirement for this is that
a customer-specic module (KSM) was tted at the factory. Further information, connection and signal descriptions can be found in
the separate Guide to Fitting Bodies booklet TG Interfaces.
Caution! All work must be carried out with the ignition turned off or with the battery disconnected. In addition to the accident prevention
regulations the applicable country-specic guidelines and laws must also be observed.
TRUCKNOLOGY

6.10 Electronics
The TGS/TGX range employs many electronic systems for controlling, regulating and monitoring vehicle functions.
The electronic braking system (EBS), electronic air suspension (ECAS) and the electronic diesel injection system (EDC) are just a few
examples. Full networking of the equipment fully guarantees that sensor readings can be processed to the same extent by all control
units.This enables the number of sensors, cables and connections to be reduced, which in turn reduces the number of possible
fault-sources. On the vehicle, network cables can be recognised because they are twisted. Several CAN bus systems are used in
parallel and this enables them to be optimally adapted to perform their respective tasks.
All data bus systems are reserved for exclusive use by the MAN vehicle electronics system; access to these bus systems is prohibited
except in the case of the Body builder CAN bus see the control unit TG interface for external data exchange (KSM).
6.10.1 Display and instrumentation concept
The instrument cluster installed in the TGS/TGX is incorporated into the control unit network by means of a CAN bus system.
Faults are displayed in plain text directly in the central display or through error codes. The instrumentation receives all the information
that is displayed in the form of a CAN message. Long-life LEDs are used instead of bulbs. The annunciator panel is vehicle-specic,
i.e. only functions and ttings that have been ordered are present. If other functions are retrotted at a later date and these are to be
displayed (e.g. retrotted tail-lift, seatbelt tensioner, tipper display in the cab) the system has to be re-parameterised using MAN-cats
.
An annunciator panel that matches the new parameters can be ordered from the MAN spare parts service.
In this way, body manufacturers may elect to have the superstructure functions, e.g. tail-lift or tipper operation, parameterised on
the vehicle and the instrumentation, together with the required symbols on the annunciator panel, installed during manufacture.
It is neither possible to incorporate superstructure functions on an in reserve basis nor is it permitted for the body manufacturer
to incorporate his own functions into the central display or tap signals from the back of the instrumentation.
6.10.2 Diagnostics concept and parameterisation using MAN-cats
MAN-cats
is the second generation MAN tool for diagnosis and parameterisation of electronic vehicle systems. MAN-cats
is therefore
used by all MAN service centres. If the body manufacturer or the customer informs MAN of the intended use or the body type
(e.g. for the intermediate speed control interface) when the vehicle is ordered, these can be incorporated into the vehicle at
the factory using EOL programming (EOL = end of line). MAN-cats
must be used if these parameters are to be changed.

For certain types of intervention in the vehicle systems the electronics specialists at MAN service centres are able to contact systems
specialists at the MAN factory to obtain the appropriate clearances, approvals and system solutions.
6.10.3 Parameterisation of the vehicle electronics
If any modications that require approval or that are critical to safety are carried out on the vehicle, or if the chassis needs to
be modied to adapt it to the body, or if conversion work or retrotting work needs to be carried out, a MAN-cats
specialist at
the nearest MAN service station must be consulted before any work commences to see if the vehicle needs to be re-parameterised.
TRUCKNOLOGY

6.10.4 ESP yaw rate sensor
The position and the mounting of the yaw rate sensor must not be modied.
Fig 113: Example of an ESP yaw rate sensor installation ESC-561
TRUCKNOLOGY

A
6.10.5 Emergency Brake Assist
The Emergency Brake Assist system (EBA) is a driver/brake assist system. It warns the driver of a potential rear-end collision accident
and initiates action when it detects an emergency situation. If necessary, the EBA will automatically apply the vehicles brakes in order
to minimise the effects of a collision or avoid an accident entirely.
The EBA receives information about road and trafc conditions in front of the vehicle from a radar sensor mounted within the front
bumper (see gure 114 detail A).
Fig. 114: Front of cab showing the installed position of the radar sensor using an EfcientLine vehicle as an example ESC-565
30 mm
40 mm
120 mm
70 mm 90 mm
45
TRUCKNOLOGY

1
A
Fig. 115: Front of cab detail A (radar sensor with cover) ESC-566
The radar sensor is a safety-relevant component and is tted behind a cover (see gure 115, number 1) in the vicinity of the step surface
on the front of the vehicle. To ensure trouble-free operation of the EBA it is essential that the following points are observed:
It must be ensured during the operation of vehicles tted with the EBA system, that the radar sensor cannot be either temporarily or
permanently obscured. The sensor detection zone will be limited if the area scanned by the radar is partially or fully masked by any
(front-end) attachments. The following illustration shows the minimum eld scanned by the radar sensor that must be kept free of
obstructions.
Fig. 116: Field scanned by the radar sensor ESC-562
TRUCKNOLOGY

Caution: On vehicles where the eld scanned by the radar sensor is either temporarily or permanently obscured by attachments or other
components (e.g. snowplough blade, cable winch attachment, other covers or any type of plate etc.), the EBA and ACC functions must
be permanently deactivated using a conversion data le.
During operation, exible components on the vehicle or attachments (electric cables, hoses, wire cables or similar) must also
be prevented from entering the eld scanned by the radar sensor.
For trouble-free operation of the EBA the following points must also be observed:
The position of the radar sensor determined at the factory, its cover and attachment bracket may not be altered.
Neither the position nor the location, material or surface characteristics (using adhesives, grinding, painting etc.) may
be modied.
The bracket including the attachment point for the radar sensor may not be loosened or modied.
Attaching other components or cables/hoses to the sensor bracket is not permitted.
Modications to or interventions in the wiring harness are not permitted.
If loosening the attachment bracket or removing the radar sensor cannot be avoided due to maintenance or repair work, the following
guidelines must also be observed for re-installation:
The radar sensor together with its bracket and cover must be re-attached in the position determined by the factory.
Only original MAN parts may be used for attachment purposes or as spares.
The sensor must be calibrated by a MAN Service Centre.
The EBA warns the driver with (among others) an acoustic signal, as soon as it detects a risk of collision. To ensure that this acoustic
signal will always operate properly, the original MAN loudspeakers (dual coil speakers) must be left in-place.
As soon as the Emergency Brake Assist system applies the vehicles brakes the brake lights are activated to warn following trafc.
Changing the brake lights tted at the factory or replacing them with rear light units that are not approved by MAN is therefore not
permitted. Further information about the lighting installation can be found in section 6.6 Lighting installation.
Following modications to the rear axle/rear axles, to the main frame of the vehicle or changes of tyre type and the installation of
additional axles, the sensor must be calibrated by correspondingly trained personnel/an MAN Service Centre. Once the modication
work has been completed the parameterisation of the vehicles electronics must be checked and adjusted where required.
TRUCKNOLOGY

7. Power take-off See separate booklet
8. Brakes, lines
The braking system is among the most important safety components on a truck. No changes should be made to any part of the brake
system including the brake lines except by suitably trained personnel. After any change a complete visual, audible, function and
efciency test of the complete braking system is to be performed.
8.1 ALB, EBS braking system
Due to the EBS it is not necessary for the body manufacturer to check the ALB (automatic load-dependent brake system); it is in any
case not possible to make adjustments. A check may possibly be required in line with the scheduled inspection of the braking system
(in Germany SP and section 29 StVZO). Should such an inspection of the braking system become necessary then a voltage
measurement using the MAN-cats diagnosis system or a visual check of the angle of the linkage at the axle load sensor must be carried
out. The EBS of vehicles tted with air suspension uses the axle load signal transmitted by the ECAS via the CAN data bus.
If conversions are carried out it must be ensured that this axle load information is not affected.
Never pull-out the plug on the axle load sensor. Before exchanging leaf springs, e.g. replacing them with springs for a different load,
it should be checked with the MAN workshop whether reparameterisation of the vehicle is necessary in order to be able to set the ALB
correctly.
8.2 Brake and compressed air lines
8.2.1 Basic principles
Polyamide (PA) tubes must in all circumstances:
- be kept away from heat sources
- be laid in such a way that no abrasion can occur
- be free from trapped stresses
- be laid without kinking.
Only PA tubing in accordance with DIN 74324 part 1 or to MAN standard M 3230 Part 1 is to be used
(www.normen.man-nutzfahrzeuge.de, registration required). In accordance with the standard this tubing is marked with
a number starting with M 3230 or ISO7628 every 350 mm.
Remove lines to protect them before welding work takes place.
For welding work, see also the Chapter Modifying the chassis Welding the frame section.
In view of the risk of heat build-up, PA pipes must not be attached to metal pipes or holders that are connected to
the following assemblies:
- Engine
- Air compressor
- Heating
- Radiator
- Hydraulic system.
TRUCKNOLOGY

Plug element
Air escapes if plug element is not
fully engaged
Plug connection fully engaged
(2
nd
detent)
O-ring to build up preload force and prevent
dirt from entering
O-ring for thread sealing
O-ring for plug element sealing
Retaining element

Plug connection not fully engaged
(1
st
detent) air loss occurs
Union screw
Brake servo
8.2.2 Voss 232 system plug connectors
For brake/air lines, only Voss 232 (MAN standard: M 3298) and Voss 230 system plug connectors (for NG6 smaller diameter pipes and
special connectors such as the double mandrel; MAN standard: M 3061) are permitted (www.normen.man-nutzfahrzeuge.de,
registration required). The standard referred to contains detailed instructions that must be applied in all cases when installing pneumatic
lines and assemblies. Body manufacturers can obtain the MAN standards listed here from www.normen.man-nutzfahrzeuge.de
(registration required).
The system 232 has two detent stages. If the plug element has only been inserted as far as the rst detent, the System 232
connection leaks deliberately; incorrect plug element engagement can be identied immediately by the noise that occurs.
The system must be relieved of pressure before the union screw is slackened.
After the connection between plug element and union screw has been separated the union screw must be renewed,
since the retaining element is rendered unt for further use when it is unscrewed.
The union screw must therefore be slackened off when a line is detached from an assembly. The plastic pipe with plug
element, union screw and retaining element constitutes a re-usable unit. Only the O-ring that seals the thread (see Fig. 117)
has to be renewed. (Grease the O-ring and clean the union screw when installing).
The plug connection unit described above is to be screwed into the assembly hand-tight, then nally tightened to 12 2 Nm
in metal and plastic (MAN Standard: M 3021, www.normen.man-nutzfahrzeuge.de, registration required).
Fig. 117: Voss System 232, functional principle ESC-174
TRUCKNOLOGY

8.2.3 Installing and attaching lines
Basics of installing lines:
Lines must not be laid loose; existing means of attachment and/or conduits are to be used.
Do not heat plastic pipes when installing them, even if they are to follow a curved path.
When attaching pipes, make sure that the PA pipes cannot become twisted.
Install a pipe clip or, in the case of a cluster of pipes, a cable tie at the beginning and end in each case.
Corrugated wiring harness pipes are to be attached to plastic consoles in the frame or, in the engine area,
to prepared cable routes using cable ties or clips.
Never attach more than one line to the same hose clip.
Only PA pipes (PA = polyamide) designed to DIN 74324 Part 1 or MAN Standard M 3230 Part 1
(extension of DIN 74324 Part 1) may
be used (www.normen.man-nutzfahrzeuge.de, registration required).
The cross-section of pipes or lines may not be changed
Add 1% to the length of the PA pipe (corresponding to 10 mm for each metre of cable), because plastic pipes contract in
the cold and the vehicles must be capable of working at temperatures down to - 40C.
The pipes must not be heated when installed.
When cutting plastic pipes to length, use plastic pipe cutters; sawing them to length creates ridges on the cut faces and
chippings get into the pipe.
PA pipes may rest on the edges of the frame or in the frame openings. A minimal amount of attening at the points of
contact is tolerated (maximum depth of 0.3 mm). However, notched abrasion is not permitted.
PA pipes are allowed to come into contact with each other. There should be minimal attening at the points where
the pipes come into contact with each other.
PA pipes can be bundled together with a cable tie but must be positioned parallel to each other (they should not cross over
each other). PA pipes and corrugated pipes should only be bundled together with pipes of the same type.
The restriction in movement
caused by the pipes becoming stiffer when bundled together should be taken into account.
Covering the edges of the frame with a cut corrugated pipe will cause damage; the PA pipe will be worn at the point where it
comes into contact with the corrugated pipe.
Points of contact with the edges of the frame can be protected with a protective spiral (see Fig. 118).
The protective spiral must tightly and completely grip the pipe it is protecting. Exception: PA pipes 6 mm).
Fig. 118: Protective spiral on a PA pipe ESC-151

TRUCKNOLOGY

PA pipes/PA corrugated pipes must not come into contact with aluminium alloys, e.g. aluminium tank, fuel lter housing;
aluminium alloys are subject to mechanical wear (re risk).
Pipes that cross over and pulsate (e.g. fuel pipes) must not be joined together with a cable tie at the cross-over point
(risk of chang).
No cables/pipes should be xed rigidly to injection pipes and steel fuel feed pipes for the ame starting system
(re risk, risk of chang).
Accompanying central lubricating cables and ABS sensor cables may be attached to air hoses only if a rubber spacer is tted.
Nothing may be attached to coolant hoses and hydraulic hoses (e.g. steering hoses) by means of cable ties (risk of chang).
Under no circumstances should starter cables be bundled together with fuel or oil pipes; this is because it is essential that
the cable from the positive terminal does not chafe.
Effects of heat: watch out for a build-up of heat in encapsulated areas. Resting the pipes/cables on heat shields is not
permitted (minimum distance from heat shields 100 mm, from the exhaust 200 mm)
Metal pipes are pre-strengthened and must not be bent or installed in such a way that they bend during operation.
If assemblies/components are mounted in such a way that they can move with respect to each other, then the following basic rules must
be followed when routing cables/pipes:
The cable/pipe must be able to follow the movement of the assembly without any problem; ensure that there is sufcient
distance between the moving parts for this (rebound/compression, steering angle, tilting of cab). The cables must not be stretched.
The respective starting and end point of the movement is to be dened exactly and used as the xed clamping point.
The PA or corrugated pipe is gripped tightly at the clamping point using the widest cable tie possible or a clip suitable for
the diameter of the pipe.
If PA and corrugated pipes are laid at the same junction, the stiffer PA pipe is laid rst. The softer corrugated pipe is then
attached to the PA pipe.
If a pipe is to tolerate movements at right angles to the direction in which it is laid, then sufcient distance between
the clamping points must be guaranteed (rule of thumb: distance between clamping points 5 x the amplitude of
movement to be withstood).
Large amplitudes of movement are best withstood by laying the pipe in a U-shape and by permitting movement along
the arms of the U.

Rule of thumb for the minimum length of the slack loop:
Minimum length of the slack loop = 1/2 amplitude of movement minimum radius
The following minimum radii are to be observed for PA pipes (the respective start and end point of the movement is
to be dened precisely as the xed clamping point):
Table 32: Minimum bending radii for PA pipes
Nominal pipe diameter - [ mm ] 4 6 9 12 14 16
Bending radius r [ mm ] 20 30 40 60 80 95
Use plastic clips to secure the lines and comply with the maximum clip spacing stated in Table 33.
Table 33: Maximum space between clips used to secure pipes in relation to pipe size
Pipe size 4 x 1 6 x 1 8 x 1 9 x 1,5 11 x 1,5 12 x 1,5 14 x 2 14 x 2,5 16 x 2
Clip spacing [mm] 500 500 600 600 700 700 800 800 800
51
52
70
72
59
58
71
53
57
55
54
56
TRUCKNOLOGY

8.2.4 Compressed air loss

Compressed air systems cannot achieve 100% efciency and slight leakage is often unavoidable despite the most careful installation
work. The question is therefore what degree of air pressure loss is unavoidable and when does the loss become too high? Simply put,
any loss of air pressure that would render a vehicle undriveable once the engine is started after a period of 12 hours parked must be
regarded as unacceptable. Based on this requirement there are two different methods of determining whether air loss is unavoidable or not:
Within 12 hours of the system having been charged to its cut-off pressure, the pressure must not be below < 6 bar in any circuit.
The check must be made with depressurised spring-loaded brake release units, in other words with the parking brake applied.
The pressure in the tested circuit must not have fallen by more than 2% within ten minutes of charging the system
to its cut-off pressure.
If air loss is greater than described above, an unacceptable leak is present and must be eliminated.
8.3 Connecting additional air consumers
All of the compressed air system pipework on the TGX/TGS uses the Voss systems 232 and 230 (for small pipes NG6 and special
connectors e.g. double mandrel). Only use of the original system components is permitted when working on the chassis.
Additional air consumers on the superstructure may only be connected to the compressed-air system via the additional consumers
circuit. A dedicated pressure relief valve must be tted for each additional consumer with a pneumatic connection > NG6 (6 x 1 mm).
The connection of additional air consumers to the following is not permitted:
To the service and parking brake circuits or to the trailer brake controller.
To the test connections (mounted on a distribution panel in an easily accessible location on the left side of the vehicle)
Directly to the four circuit protection valve
MAN uses a distribution rail on the solenoid-valve block to connect its own air-consumers. This is installed on to the cross member at the
bend in the frame. In a few exceptional cases it is installed laterally on the gusset plate of the cross member or on the left longitudinal
frame member as seen from the direction of travel (vehicles with wheel formula 8x6, 8x8).
Body manufacturers have two connection options:
The connections on the distribution rail are occupied by pipes, depending on the equipment tted. When the vehicle leaves the factory,
connections 52, 53, 54, 58 und 59 may be occupied to supply vehicle functions. It cannot be guaranteed therefore, that it will be possible
to connect additional ancillary consumers with a VOSS system 232 NG8 plug to one of these connections. In such cases, the overow
valve that must be tted separately by the bodybuilder must be connected using Voss plug L-SN12-KN12-KN12 (MAN-part number
81.98183-6101). The supply pipe must therefore be separated from the distribution rail.
Fig. 119: Location of the distribution block for additional air-consumers ESC-180a
Front view Rear view
The other possibility is a connection to a pressure relief and non-return valve, available from the factory for ancillary consumers mounted
on the body. Pressure relief 7,3
-0,3
bar (MAN No 81.52110.6049).
TRUCKNOLOGY

8.4 Retrotting continuous brakes not manufactured by MAN
Fitting continuous braking systems (retarders, eddy current brakes) that have not been documented by MAN is fundamentally not
possible. Retrotting of continuous brakes not manufactured by MAN is not permitted because the necessary intervention in the
electronically controlled braking system (EBS) and the vehicles on-board braking and drivetrain management system is not permitted.
9. Calculations
9.1 Speed
The following generally applies for the calculation of the driving speed on the basis of engine speed, tyre size and overall ratio:
Formula 18: Speed

0,06 n
Mot
U
v =
i
G
i
v
i
A
Where:
v = Driving speed, in [km/h]
n
Mot
= Engine speed, in [rpm]
U = Tyre rolling circumference, in [m]
I
G
= Transmission ratio
i
V
= Transfer case ratio
i
A
= Final drive ratio of the driven axle(s)
To calculate the theoretical maximum speed (or the design top speed), the engine speed is increased by 4%.
The formula therefore is as follows:
Formula 19: Theoretical maximum speed
0,0624 n
Mot
U
v =
i
G
i
v
i
A

Caution: This calculation is used exclusively to calculate the theoretical nal speed on the basis of engine speed and
transmission ratios. The formula does not take into consideration the fact that the actual maximum speed will be below this speed when
driving resistances offset the driving forces. An estimate of the actual achievable speeds using a driving performance calculation in
which air, rolling and climbing resistance on the one side and tractive force on the other offset each other, can be found in Section 9.8,
Driving resistances. On vehicles with a speed limiter in accordance with 92/24/EEC, the design top speed is generally 90 km/h.
Example of a calculation:

Vehicle: Model 56S TGS 33.430 6x6 BB
Tyre size: 315/80 R 22,5
Rolling circumference: 3,280 m
Transmission: ZF 16S 2522 TO
Transmission ratio in lowest gear: 13,80
Transmission ratio in highest gear: 0,84
Minimum engine speed at maximum engine torque: 1.000/min
Maximum engine speed: 1.900/min
Ratio for transfer case G 172 in on-road applications: 1,007
Ratio for transfer case G 172 in off-road applications: 1,652
Final drive ratio: 4,00
TRUCKNOLOGY

The solution to following is required:
1. Minimum speed in off-road applications at maximum torque
2. Theoretical maximum speed without speed limiter
Solution 1:
0,06 1000 3,280
v =
13,8 1,652 4,00
v = 2,16 km/h
Solution 2:
0,0624 1900 3,280
v =
0,84 1,007 4,00
v = 115 km/h
A speed of 115km/h is theoretically possible, however the speed limiter limits this to 90km/h.
(The speed is actually set to 89km/h as a result of the tolerances that must be taken into account).
9.2 Efficiency
The efficiency is the ratio of the power output to the power input. Since the power output is always smaller than the power input,
efficiency is always < 1 or < 100%.
Formula 20: Efficiency

P
ab
=
P
zu
When several units are connected in series, the individual efficiencies are multiplied.
Example of a calculation for individual efficiency:
Efficiency of a hydraulic pump = 0,7. If the required power output P
ab
is 20 kW, what should the power input P
zu
be?
Solution:
P
ab
P
zu
=

20
P
zu
=
0,7
P
zu
= 28,6 kW
TRUCKNOLOGY

Example of calculation for several efciencies:
Efciency of a hydraulic pump
1
= 0,7. This pump drives a hydraulic motor via a jointed shaft system with two joints.
Individual efciencies:

Hydraulic pump:
1
= 0,7
Jointed shaft joint a:
2
= 0,95
Jointed shaft joint b:
3
= 0,95
Hydraulic motor:
4
= 0,8
Power required, i.e., power output P
ab
= 20 kW
What is the power input P
zu
?
Solution:
Overall efciency:

ges
=
1

2

3

4

ges
= 0,7 0,95 0,95 0,8

ges
= 0,51
Power input:

20
P
zu
=
0,51
P
zu
= 39,2 kW
9.3 Tractive force
The tractive force is dependent on:
Engine torque
Overall ratio (including that of the wheels)
Efciency of power transmission
Formula 21: Tractive force
2 M
Mot
i
G
i
V
i
A
F
z
=
U
F
Z
= Tractive force, in [N]
M
Mot
= Engine torque, in [Nm]
= Overall efciency in the drive train see guideline values in Table 35
i
G
i
V
i
A
= Final drive ratio of the driven axle(s)
U = Tyre rolling circumference, in [m]
For an example of tractive force, see 9.4.3 Calculating gradeability.
TRUCKNOLOGY

9.4 Gradeability
9.4.1 Distance travelled on uphill or downhill gradients
The gradeability of a vehicle is expressed as a percentage (%). For example, the gure 25% means that for a
horizontal length of I = 100m, a height of h = 25m can be overcome. The same applies correspondingly to downhill gradients.
The actual distance travelled c is calculated as follows:
Formula 22: Distance travelled on uphill or downhill gradients
p
2
c = I
2
+ h
2
= I 1 +
100

c = Distance travelled, in [m]
l = Horizontal length of an uphill or downhill gradient, in [m]
h = Vertical height of an uphill/downhill gradient, in [m]
p = Uphill/downhill gradient, in [%]
Gradient p = 25%. What is the distance travelled for a length of 200 m?
25
2
c = I
2
+ h
2
= 200 1 +
100
c = 206 m
9.4.2 Angle of uphill or downhill gradient
The angle of the uphill or downhill gradient a is calculated using the following formula:
Formula 23: Angle of uphill or downhill gradient
p p h h
tan = , = arctan , sin = , = arcsin
100 100 c c
a = Angle of gradient, in []
p = Uphill/downhill gradient, in [%]
h = Vertical height of an uphill/downhill gradient, in [m]
c = Distance travelled, in [m]
If the gradient is 25%, what is the angle of the gradient?

p 25
tan = =
100 100
= arctan 0,25
= 14
0
5
10
20
40
0
10
20
30
70
80
90
100 1:1
1:1,1
1:1,3
1:1,4
1:1,7
1:2
1:2,5
1:3,3
1:5
1:10
45
30
35
25
15
TRUCKNOLOGY

D
o
w
n
h
i
l
l

g
r
a
d
i
e
n
t

U
p
h
i
l
l

g
r
a
d
i
e
n
t
G
r
a
d
i
e
n
t
G
r
a
d
i
e
n
t

r
a
t
i
o
Fig. 120: Gradient ratios, gradient, angle of gradient ESC-171
9.4.3 Calculating the gradeability
Gradeability is dependent on:
Tractive force (see Formula 21)
Overall combined mass, including overall mass of the trailer or semi-trailer
Rolling resistance
Adhesion (friction)
The following applies for gradeability:
Formula 24: Gradeability
F
z
p = 100 - f
R

9,81 G
z
Where:
p = Gradeability, [%]
M
Mot
= Engine torque, in [Nm]
F
z
= Tractive force in [N] (calculated in accordance with Formula 21)
G
z
= Overall combined mass, in [kg]
f
R
= Coefcient of rolling resistance, see Table 34
i
G
i
A
= Driven axle ratio
i
V
U = Tyre rolling circumference, [m]
= Overall efciency in the drive train, see Table 35
TRUCKNOLOGY

Formula 24 calculates the vehicles gradeability based on its characteristics of
Engine torque
Transmission, transfer case, nal drive and tyre ratio and
Overall combined mass
Here, only the vehicles ability to tackle a specic gradient based on its characteristics is considered. Not taken into consideration is
the actual adhesion between wheels and road which, in poor conditions (e.g. wet roads) can reduce traction so that hill-climbing
performance is far below the value calculated here. Calculation of the actual conditions based on adhesion is addressed in Formula 25.
Table 34: Coefcients of rolling resistance
Road surface Coefcient f
R
Good asphalt road 0,007
Wet asphalt road 0,015
Good concrete road 0,008
Rough concrete road 0,011
Block paving 0,017
Poor road 0,032
Dirt track 0,15...0,94
Loose sand 0,15...0,30

Table 35: Overall efciency in the drive train
Number of driven axles
One driven axle 0,95
Two driven axles 0,9
Three driven axles 0,85
Four driven axles 0,8

Example of calculation:

Vehicle: Model 56S TGS 33.430 6x6 BB
Max. engine torque: M
Mot
= 2.100 Nm
Efciency with three driven axles:
ges
= 0,85
Transmission ratio in lowest gear: i
G
= 13,80
Transfer case ratio - in on-road gear: i
V
= 1,007
- in off-road gear: i
V
= 1,652
Final drive ratio: i
A
= 4,00
Tyre 315/80 R 22.5 with rolling circumference: U = 3,280 m
Overall combined mass: G
Z
= 100.000 kg
Coefcient of rolling resistance:
- smooth asphalt f
R
= 0,007
- poor, rutted road f
R
= 0,032
TRUCKNOLOGY

Required is:
Maximum gradeability p
f
in on-road and off-road conditions.
Solution:
1. Maximum tractive force (for denition, see Formula 21) in on-road gear:
2 M
Mot
i
G
i
V
i
A
F
z
=
U
2 2100 0,85 13,8 1,007 4,00
F
z
=
3,280
F
z
= 190070 N = 190,07 kN

2. Maximum tractive force (for denition, see Formula 21) in off-road gear:
2 M
Mot
i
G
i
V
i
A
F
z
=
U
2 2100 0,85 13,8 1,007 4,00
F
z
=
3,280
F
z
= 311812 N = 311,8 kN

3. Maximum gradeability in on-road gear on good asphalt road:

F
z
p = 100 - f
R

9,81 G
z
190070
p = 100 - 0,007
9,81 100000
p = 18,68%
4. Maximum gradeability in on-road gear on poor, rutted road:

190070
p = 100 - 0,032
9,81 100000
p = 16,18%
TRUCKNOLOGY

5. Maximum gradeability in off-road gear on good asphalt road:

311812
p = 100 - 0,007
9,81 100000
p = 31,09%
6. Maximum gradeability in off-road gear on poor, rutted road:
311812
p = 100 - 0,032
9,81 100000
p = 28,58%
Note:
The examples shown do not take into consideration whether adhesion between road and driven wheels (friction) will allow the tractive
force required for tackling the gradient to be transmitted. The following formula is applied for this:
Formula 25: Gradeability taking into account road/tyre adhesion
G
an
p
R
= 100 - f
R

G
z

Where:

p
R
= Gradeability taking friction into account, in [%]
= Tyre/road surface coefcient of friction, on wet asphalt surface ~ 0,5
f
R
= Coefcient of rolling resistance, on wet asphalt road surface ~ 0,015
G
an
= Sum of the axle loads of the driven axles as mass, in [kg]
G
Z
Example of calculation:

Above vehicle: Model 56S TGS 33.430 6x6 BB
Coefcient, wet asphalt road: = 0,5
Coefcient of rolling resistance, wet asphalt: f
R
= 0,015
Overall combined mass: G
Z
= 100.000 kg
Sum of the axle loads of all driven axles: G
an
= 26.000 kg
0,5 26000
p
R
= 100 - 0,015
100000
p
R
= 11,5%
TRUCKNOLOGY

9.5 Torque
If force and effective separation are known:
Formula 26: Torque with force and effective separation

M = F I
If power output and rotational speed are known:
Formula 27: Torque with power output and rotational speed

9550 P
M =
n
In hydraulic systems, if delivery rate (volume ow rate), pressure and rotational speed are known:
Formula 28: Torque with delivery rate, pressure and rotational speed
15,9 Q p
M =
n
Where:

M = Torque, in [Nm]
F = Force, in [N]
l = Distance from the line of action of the force to the centre of rotation, in [m]
P = Power output, in [kW]
n = Rotational speed, in [rpm]
= Efficiency
Q = Volume flow rate, in [l/min]
p = Pressure, in [bar]
Example of calculation when force and effective separation are known:
A cable winch with a pulling force F of 50,000 N has a drum diameter d = 0.3 m.
Without taking efficiency into account, what is the torque?
Solution:
M = F l = F 0,5 d (the drum radius is the leverage)
M = 50000N 0,5 0,3 m
M = 7500 Nm
Example when power output and rotational speed are known:
A power take-off is to transmit a power P of 100 kW at n = 1500/min.
Without taking efficiency into account, what torque must the power take-off be able to transmit?
TRUCKNOLOGY

Solution:

9550 100
M =
1500
M = 637 Nm
Example if delivery rate (volume ow rate), pressure and rotational speed are known for a hydraulic pump:
A hydraulic pump delivers a volume ow rate Q of 80 l/min at a pressure p of 170 bar and a pump rotational speed n of 1000/min.
Without taking efciency into account, what torque is required?
Solution:

15,9 80 170
M =
1000
M = 216 Nm
If efciency is to be taken into account, the torques calculated in each case must be divided by the overall efciency
(see also Section 9.2, Efciency).
9.6 Power output
For lifting motion:
Formula 29: Power output for lifting motion

9,81 m v
M =
1000
For plane motion:
Formula 30: Power output for plane motion
F v
P =
1000
For rotational motion:
Formula 31: Power output for rotational motion
M n
P =
9550
TRUCKNOLOGY

In hydraulic systems:
Formula 32: Power output in hydraulic systems
Q p
P =
600
Where:
P = Power output, in [kW]
m = Mass, in [kg]
v = Speed, in [m/s]
= Efciency
F = Force, in [N]
M = Torque, in [Nm]
n = Rotational speed, in [rpm]
Q = Delivery rate (volume ow rate), in [l/min]
p = Pressure, in [bar]
Example 1 = Lifting motion:
Tail-lift payload including its own weight m = 2. 600 kg
Lift speed v = 0,2 m/s
If efciency is not taken into consideration, what is the power output?
Solution:

9,81 2600 0,2
P =
1000
P = 5,1 kW
Example 2: Plane motion:
Cable winch F = 100.000 N
Cable speed v = 0,15 m/s
If efciency is not taken into consideration, what is the power output requirement?

100000 0,15
P =
1000
P = 15 kW
Example 3 Rotational motion:
Power take-off rotational speed n = 1.800/min
Permissible torque M = 600 Nm
TRUCKNOLOGY

If efciency is not taken into consideration, what power output is possible?
Solution:
600 1800
P =
9550
P = 113 kW
Example 4: Hydraulic system:
Volume flow rate of the pump Q = 60 l/min
Pressure p = 170 bar
If efficiency is not taken into consideration, what is the power output?
Solution:
60 170
P =
600
P = 17 kW
9.7 Rotational speeds for power take-offs at the transfer case
If the power take-off is operating on the transfer case and its operation is distance-dependent, its rotational speed n
N
is given in
revolutions per metre of distance covered. It is calculated from the following:
Formula 33: Revolutions per meter, power take-off at the transfer box
i
A
i
V
n
N
=
U
The distance s in metres covered per revolution of the power take-off (reciprocal value of n
N
) is calculated with:
Formula 34: Distance per revolution, power take-off on the transfer case

U
s =
i
A
i
V
Where:
n
N
= Power take-off rotational speed, in [1/m]
i
A
= Final drive ratio
i
V
U = Tyre circumference, in [m]
s = Distance travelled, in [m]
Example:
Vehicle: Model 80S TGS 18.480 4x4 BL
Tyres 315/80 R22.5 with rolling circumference: U = 3,280 m
Final drive ratio: i
A
= 5,33
Transfer case G172, ratio in on-road gear: i
v
= 1,007
Ratio in off-road applications: i
v
= 1,652
TRUCKNOLOGY

Power take-off rotational speed in on-road gear:
5,33 1,007
n
N
=
3,280
n
N
= 1,636/m
This corresponds to a distance of:

3,280
s =
5,33 1,007
s = 0,611 m
Power take-off rotational speed in off-road gear:
5,33 1,652
n
N
=
3,280

n
N
= 2,684 m
This corresponds to a distance of:
3,280
s =
5,33 1,652
s = 0,372 m
9.8 Driving resistances
The main driving resistances are:
Rolling resistance
Climbing resistance
Air resistance (drag).
A vehicle can move along only if the sum of all resistances is overcome. Resistances are forces that either balance out the driving
force (uniform movement) or are smaller than the driving force (accelerated movement).
Formula 35: Rolling resistance force
F
R
= 9,81 f
R
G
z
cos
Formula 36: Climbing resistance force
F
S
= 9,81 G
z
sin
TRUCKNOLOGY

Angle of gradient (= formula 23, see Section 9.4.2, Angle of uphill and downhill gradients)
p p
tan = , = arctan
100 100
Formula 37: Air resistance force
F
L
= 0,6 c
W
A v
2
Where:
F
R
= Rolling resistance force, in [N]
f
R
= Coefcient of rolling resistance, see Table 34
G
Z
= Angle of uphill gradient, in []
F
S
= Climbing resistance force, in [N]
p = Uphill gradient, in [%]
F
L
= Air resistance force, in [N]
c
W
= Drag coefcient
A = Vehicle frontal area, in [m]
v = Speed, in [m/s]
Example:
Articulated vehicle: G
Z
= 40.000 kg
Speed: v = 80 km/h
Gradient: p
f
= 3%
Vehicle frontal area: A = 7 m
Coefcient of rolling resistance for good asphalt road: f
R
= 0,007
A distinction is to be made between the following:
with spoiler, c
W1
= 0,6
without spoiler, c
W2
= 1,0
Solution:
Additional calculation 1:
Conversion of driving speed from km/h into m/s:

80
v = = 22,22m/s
3,6
Additional calculation 2:
Conversion of gradeability from % into degrees:
3
= arctan = arctan 0,03
100
= 1,72
TRUCKNOLOGY

1. Calculation of rolling resistance:

F
R
= 9,81 0,007 40000 cos 1,72
F
R
= 2746 N
2. Calculation of climbing resistance:

F
S
= 9,81 40000 sin 1,72
F
S
= 11778 N
3. Calculation of air resistance F
L1
with spoiler:
F
L1
= 0,6 0,6 7 22,22
2
F
L1
= 1244 N
4. Calculation of air resistance F
L2
without spoiler:

F
L2
= 0,6 1 7 22,22
2
F
L2
= 2074 N
5. Overall resistance F
ges1
with spoiler:
F
ges1
= F
R
+ F
s
+ F
L1

F
ges1
= 2746 + 11778 + 1244

F
ges1
=

15768 N

6. Overall resistance F
ges2
without spoiler:
F
ges2
= F
R
+ F
s
+ F
L2

F
ges2
= 2746 + 11778 + 2074

F
ges2
=

16598 N
7. Power output requirement P
1
with spoiler, not taking efciency into consideration:
(power output in accordance with Formula 30, Power output for plane motion)
F
ges1
v
P
1
=
1000
15768 22,22
P
1
=
1000
P
1
= 350 kW (476 PS)
TRUCKNOLOGY

2
without spoiler, not taking efciency into consideration:
F
ges2
v
P
2
=
1000
16598 22,22
P
2
=
1000
P
2
= 369 kW (502 PS)
1
with spoiler and overall driveline efciency of = 0,95:

P
1
350
P
1
= =
0,95
P
1
= 368 kW (501 PS)
2
with spoiler and overall driveline efciency of = 0,95:
P
2
369
P
2
= =
0,95
P
2
= 388 kW (528 PS)
9.9 Turning circle
When a vehicle is cornering, each wheel describes a turning circle. The outer turning circle, or its radius, is the main subject of interest.
The calculation is not precise because when a vehicle is cornering the perpendiculars through the centres of all wheels do not intersect
at the curve centre point (Ackermann condition). In addition, while the vehicle is moving dynamic forces will arise that will affect the
cornering manoeuvre. However, the following formulae can be used for estimation purposes:
Formula 38: Distance between steering axes
j = s - 2r
o
Formula 39: Theoretical value of the outer steer angle
j
cot
ao
= cot
i
+
l
kt
Formula 40: Steer angle deviation

F
=
a
-
ao

Formula 41: Turning circle radius
l
kt
r
s
= + r
o
- 50
F
sin
ao
l
k
t
j
j
s
a0
i
r
0
r
0
r
0
0
TRUCKNOLOGY

O
uter turning circle
Fig. 121: Kinematic interrelationships when calculating the turning circle ESC-172
Example:

Vehicle: Model 06X TGX 18.350 4x2 BL
Wheelbase: l
kt
= 3.900 mm
Front axle: Model VOK-09
Tyres: 315/80 R 22.5
Rims: 22.5 x 9.00
Track width: s = 2.048 mm
Scrub radius: r
0
= 49 mm
Inner steer angle:
i
= 49,0
Outer steer angle:
a
= 3245 = 32,75
1. Distance between steering axes
j = s - 2 r
o
= 2048 - 2 49
j = 1950
2. Theoretical value for outer steer angle
j 1950
cot
ao
= cot
i
+ = 0,8693 +
l
kt
3900
cot
ao
= 1,369

ao
= 36,14
1600
4500
G = 260 kg
TRUCKNOLOGY

Theoretical rear
axle centreline
3. Steering deviation

F
=
a
-
ao
= 32,75 - 36,14 = -3,39

4. Turning circle radius
3900
r
s
= + 49 - 50 (-3,39)
sin 36,14

r
s
= 6831 mm
9.10 Axle load calculation
9.10.1 Performing an axle load calculation
To optimise the vehicle and achieve the correct superstructure ratings, an axle load calculation is essential. The body can be matched
properly to the truck only if the vehicle is weighed before any body building work is carried out. The weights obtained in the weighing
process are to be included in the axle load calculation.
The following section will explain an axle load calculation. The moment theorem is used to distribute the weight of the equipment to
the front and rear axles. All distances are with respect to the theoretical front axle centreline. For ease of understanding, weight is not
used in the sense of weight force (in N) in the following formulae but in the sense of mass (in kg).
Example:
A 400 litre tank is to be installed instead of a 140 litre tank.
A calculation of the weight distribution between the front and rear axles is required.
Difference in weight: G = 400 - 140 = 260 kg
Distance from theoretical front axle centreline = 1.600 mm
Theoretical wheelbase l
t
= 4.500 mm
Fig. 122: Axle load calculation: Tank layout ESC-550
TRUCKNOLOGY

Solution:
Formula 42: Rear axle weight difference:

G a
G
H
=
l
t

260 1600
=
4500
G
H
= 92 kg
Formula 43: Front axle weight difference:
G
V
= G G
H

= 260 - 92
G
V
= 168 kg
Rounding up or down to whole kilograms is sufcient in practice. Attention should be paid to the mathematically correct symbol,
to which the following rule applies:
Dimensions
- all distances/clearances that are IN FRONT OF the theoretical front axle centreline have a MINUS sign (-)
- all distances that are BEHIND the theoretical front axle centreline have a PLUS sign (+)
Weights
- all weights that are ADDED TO the vehicle have a PLUS sign (+)
- all equipment weights that are REMOVED FROM the vehicle have a MINUS sign (-)
Example Snowplough plate:

Weight: G = 120 kg
Distance from rst axle centreline: a = -1.600 mm
Theoretical wheelbase: l
t
= 4.500 mm
A calculation of the weight distribution to the front and rear axle is required.
Rear axle:
G a 120 (-1600)
G
H
= =
l
t
4500
G
H
= -43kg, the weight on the rear axle is reduced.
Front axle:
G
V
= G - G
H
= 120 - (-43)
G
V
= 163 kg, the weight on the front axle is increased.
The following table shows an example of a full axle load calculation. In this example, two variants are compared
(for variants see Table 36).
TRUCKNOLOGY

Table 36: Example of an axle load calculation
AXLE LOAD CALCULATION
MAN - Truck & Bus AG, Postf. 500620, 80976 Munich
Dpt. :ESC Vehicle, cab : TGL 8.210 4x2 BB 2006-12-20
Compiled by : Wheelbase : 3600 Calc. - no. : N03...........
Code : W - tech. : 3600 KSW - no. :
Tel. : Overhang : 1275 = Serie AE - no. :
Overhang : = Sonder Veh. - no :
Overhang tech. : 1275 File-no. :
VN : Vec.-drg. no. : 81.99126.0186 ESC-no. :
Customer : Body : 3.800 mm loading platform and rear-mounted crane -
Location : rigidly xed, total crane moment approx. 67 kNm
Name Dist. from
techn.
Weight distribution to Dist. from
techn.
Weight distribution to
FA-centre FA RA Total FA-centre FA RA Total
Chassis with driver, tools and spare
wheel
2.610 875 3.485 2.610 875 3.485
Trailer coupling 4.875 -12 47 35 4.875 -12 47 35
High-mounted exhaust pipe, left 480 30 5 35 480 30 5 35
Seat for driver, comfort -300 16 -1 15 -300 16 -1 15
Fuel tank steel, 150 ltr. (Serie 100 ltr.) 2.200 27 43 70 2.200 27 43 70
4.925 -4 14 10 4.925 -4 14 10
Fender plastic RA 3.600 0 25 26 3.600 0 25 25
2.905 4 16 20 2.905 4 16 20
Power take-off and pump 1.500 11 4 15 1.500 11 4 15
Tyres RA 225/75 R 17,5 3.600 0 10 10 3.600 0 10 10
Tyres FA 225/75 R 17,5 0 5 0 5 0 5 0 5
4.875 -11 41 30 4.875 -11 41 30
Seat bench -300 22 -2 20 -300 22 -2 20
Stabilisator RA 3.900 -3 33 30 3.900 -3 33 30
Other 1.280 29 16 45 1.280 29 16 45
Oil tank 1.559 60 45 105 1.559 60 45 105
Rear crane, arm folded down ** 1.020 631 249 880 0 0 0 0
Reinforcement in the crane area 1.100 31 14 45 1.100 31 14 45
Subframe u. Kippbrcke 3.250 90 840 930 3.250 90 840 930
Rear crane, arm craned ***
0 0 0 0
1.770 447 433 880
0 0 0 0
0 0 0 0
TRUCKNOLOGY

Chassis - unladen weight 3.540 2.275 5.815 3.357 2.458 5.815
Permissible loads 3.700 5.600 7.490 3.700 5.600 7.490
Difference between unladen weight & perm. loads 160 3.325 1.675 343 3.142 1.675
Centre of gravity for payload and FA fully laden X1 = 344 160 1.515 1.675 738 343 1.332 1.675
body with respect to RA fully laden X2 = -3.547 -1.650 3.325 1.675 -3153 -1467 3.142 1.675
techn. RA centreline actual X3 = 250 116 1.559 1.675 250 116 1.559 1.675
Axel overload -44 -1766 -227 -1.583
Loss of payload through axle overload 0 0
With even loading there remains 116 1559 1675 116 1.559 1.675
Payload 0 0 0 0 0 0 0 0
Vehicle laden 3.656 3834 7490 3473 4.017 7.490
Axle or vehicle loading 98,8% 68,5% 100,0% 93,9% 71,7% 100,0%
Axle load distribution 48,8% 51,2% 100,0% 46,4% 53,6% 100,0%
Vehicle unladen 3540 2275 5815 3357 2458 5815
Axle or vehicle loading 95,7% 40,6% 77,6% 90,7% 43,9% 77,6%
Axle load distribution 60,9% 39,1% 100,0% 57,7% 42,3% 100,0%
Vehicle overhang 47,2 %
*** Crane arm rests to the rear (relieves load on FA !!)
Observe the weight tolerances acc. to DIN 70020 Information supplied withour liability
9.10.2 Calculation of weight with trailing axle lifted
The weights given for trailing axle vehicles in the MANTED
system (www.manted.de) and other technical documents have been

calculated with the trailing axle lowered. Distribution of the axle loads to the front and driven axle after the trailing axle has been lifted is
easy to determine by calculation.
Weight on the 2
nd
axle (driven axle) with the 3
rd
axle (trailing axle) lifted.
Formula 44: Weight on the 2
nd
axle with 3
rd
axle lifted
G
23
l
t
G
2an
=
l
12
Where:
G
2an
= Unladen weight on the 2
nd
axle with the 3
rd
axle lifted, in [kg]
G
23
nd
and 3
rd
axles, in [kg]
l
12
= Wheelbase between 1
st
and 2
nd
axles, in [mm]
l
t
= Theoretical wheelbase, in [mm]
Weight on the front axle with the 3
rd
axle (trailing axle) lifted:
Formula 45: Weight on the 1
st
axle with the 3
rd
axle lifted
G
1an
= G - G
2an
TRUCKNOLOGY

Where:
G
1an
st
axle with the trailing axle lifted, in [kg]
G = Unladen weight of the vehicle, in [kg]
Example:
Vehicle: Model 21X TGX 26.400 6x2-2 LL
Wheelbase: 4.800 + 1.350
Frame overhang: 2.600
Cab: XXL
Unladen weight with the trailing axle lowered:
Front axle G
1ab
= 5.100 kg
Drive and trailing axle G
23
= 3.505 kg
Unladen weight G = 8.605 kg

Permissible axle loads: 7.500 kg / 11.500 kg / 7.500 kg
Solution:
1. Calculation of the theoretical wheelbase (see General Chapter):
G
3
l
23
l
t
= l
12
+
G
2
+ G
3
7.500

1.350
l
t
= 4.800 +
11.500 + 7.500
l
t
= 5.333 mm
2. Calculation of the unladen weight of the 2
nd
axle (= driven axle) with the 3
rd
axle (= trailing axle) lifted:

G
23
l
t
3.505 5.333
G
2an
= =
l
12
4.800
G
2an
= 3.894,2 kg
3. Calculation of the unladen weight of the 1
st
axle (+ front axle) with the 3
rd
axle (= trailing axle) lifted:
G
1an
= G - G
2an
G
1an
= 8.605 - 3.894,2

G
1an
= 4.710,8 kg
TRUCKNOLOGY

9.11 Support length for bodies without subframes
The calculation of the required support length in the following example does not take all inuences into account.
However, it does show one option and provides some good reference values for practical applications.
The support length is calculated using the following:
Formula 46: Formula for support length when no subframe is used
0,175 F E (r
R
+ r
A
)
l =

0,2
r
R
r
A
If the frame and support are made of different materials, then the following applies:
Formula 47: Modulus of elasticity in the case of different materials

2E
R
E
A
E =
E
R
+ E
A
Where:
l = Support length for each support, in [mm]
F = Force per support, in [N]
E = Modulus of elasticity, in [N/mm]
r
R
= External radius of frame longitudinal member prole section, in [mm]
r
A
= External radius of support prole section, in [mm]

0,2
= Yield point of the lower value material, in [N/mm]
E
R
= Modulus of elasticity of frame longitudinal member prole section, in [N/mm]
E
A
= Modulus of elasticity of support prole section, in [N/mm]
Example:
Interchangeable body chassis 21X TGX 26.400 6x2-2 LL, wheelbase 4,500 + 1,350, large-capacity cab,
permissible gross weight 26,000 kg, chassis unladen weight 8,915 kg.
Solution:
For payload and body there remains approx. 26.000 kg 8.915 kg = 17.085 kg
For each support if there are 6 bearing points on the chassis 17.085: 6 = 2.847 kg
Force F = 2.847 kg 9,81 kg m/s = 27.933 N
External radius of frame prole section r
R
= 18 mm
External radius of support prole section r
A
= 16 mm
Modulus of elasticity for steel E = 210.000 N/mm
Yield point for both materials
0,2
= 420 N/mm
Formula 46 can then be used to determine the approximate minimum length for every support:
0,175 27.933 210.000 (18+16)
l =
430
2
18 16
l = 655 mm
TRUCKNOLOGY

9.12.1 Trailer coupling
The required trailer coupling size is determined by the D value.
The formula for the D value is as follows:
Formula 48: D value
9,81 T R
D =
T + R
D = D value, in [kN]
T = Permissible gross weight of the towing vehicle, in [t]
R = Permissible gross weight of the trailer, in [t]
Example:
Vehicle 06X TGX 18.440 4x2 BL
Permissible gross weight 18,000 kg = T = 18t
Trailer load 26,000 kg = R = 26t
D value:
9,81 18 26
D =
18 + 26
D = 104 kN
If the trailer gross weight R and the D value of the coupling device are specied, the permissible gross weight of the towing
vehicle T can be determined using the following formula:
R D
T =
(9,81 R) - D
If the permissible gross weight of the towing vehicle T and the D value of the coupling device are specied, the maximum
permissible trailer load R can be determined using the following formula:
T D
R =
(9,81 T) - D
9.12.2 Rigid drawbar trailers / central axle trailers
Other conditions apply for the rigid drawbar and central axle trailers in addition to the D value. Trailer couplings and end cross members
have lower trailer loads because in this case the nose weight acting on the trailer coupling and the end cross member has to be taken
into account.
In order to harmonise the regulations within the European Union, the terms D
c
value and V value were introduced
with Directive 94/20/EC:
x
v
x
v
l l
TRUCKNOLOGY

The following formulae apply:
Formula 49: D
C
value formula for rigid drawbar and central axle trailers
9,81 T C
D
C
=
T + C
Formula 50: V value formula for central axle and rigid drawbar trailers with a permissible nose weight of < 10% of
the trailer mass and not more than 1,000 kg

X
2
V = a C
l
2

If the values for x/l have been calculated as < 1, a value of 1.0 is to be used.
Where:
D
C
= Lower D value when operating with a central axle trailer, in [kN]
T = Permissible gross weight of the towing vehicle, in [t]
C = Sum of the axle loads of the central axle trailer loaded with the permissible mass, in [t] ,not including nose weight S
V = V value, in [kN]
a = Reference acceleration in the coupling point, in m/s
2
. Two values are to be used: 1.8 m/s
2
for air
suspension or comparable suspension on the towing vehicle, and 2.4 m/s
2
on all other vehicles
x = Length of trailer body, see Fig. 123
l = Theoretical drawbar length, see Fig. 123
S = Nose weight of the drawbar on the coupling point, in [kg]
Fig. 123: Length of the trailer body and theoretical drawbar length (see also Chapter 4.8 Coupling devices) ESC-510
Example:
Vehicle: Model N13 TGL 8.210 4x2 BL
Permissible gross weight 7.490 kg = T = 7,49 t
Trailer:
Sum of the trailer axle loads: 11.000 kg = C = 11 t
Nose weight: S = 700 kg
Length of body: x = 6,2 m
Theoretical drawbar length: l = 5,2 m
Question: Can both vehicles be used in combination as a road train if the reinforced end cross member and
the Ringfeder 864trailer coupling are fitted to the truck?
TRUCKNOLOGY

Solution:
D
C
value:
9,81 T C 9,81 7,49 11
D
C
= =
T + C 7,49 + 11
D
C
= 43,7 kN
D
C
value for end cross member = 64 kN (see Chapter Coupling devices TG, Table 2)

x
2
6,2
2
= = 1,42
l
2
5,2
2
x
2
V = a C = 1,8 1,42 11 (1,8 at air suspension rearaxel)
l
2
V = 28,12 kN
V value for end cross member = 35 kN (see Chapter Coupling devices TG, Table 2)
Both vehicles can be combined to form a road train; however, the minimum front axle load of 30% of the respective vehicle weight
(including nose weight) must be observed in accordance with the General technical basics in the TGL/TGM Guide to Fitting Bodies.
An unladen truck may pull only an unladen central axle trailer.
9.12.3 Fifth-wheel coupling
The required fth-wheel coupling size is determined by the D value. The D value formula for fth-wheel couplings is as follows:
Formula 51: D value for fth-wheel coupling

0,6 9,81 T R
D =
T + R - U
If the D value is known and the permissible gross weight of the semitrailer is sought, the following applies:
Formula 52: Permissible gross weight of the semitrailer
D (T - U)
R =
(0,6 9.81 T) - D
If the permissible gross weight of the semitrailer and the D value of the fth-wheel coupling are specied, the permissible gross weight
of the tractor unit can be calculated with the following formula:
Formula 53: Permissible gross weight of the tractor unit
D (R - U)
T =
(0,6 9.81 R) - D
TRUCKNOLOGY

If the fth-wheel load is sought and all other loads are known, the following formula can be used:
Formula 54: Formula for fth-wheel load
0,6 9,81 T R
U = T + R -
D
Where:
D = D value, in [kN]
R = Permissible gross weight of the semitrailer in [t], including the fth-wheel load
T = Permissible gross weight of the tractor unit in [t], including the fth-wheel load
U = Fifth-wheel load, in [t]
Example:
Tractor unit: 10X TGX 18.400 4x2 LL
Fifth wheel load, in accordance with trailer type plate: U = 10.750 kg = 10,75 t
Permissible gross weight of the tractor unit: 18.000 kg = T = 18 t
Permissible gross weight of the semitrailer: 32.000 kg = R = 32 t
D value:
0,6 9,81 18 32
D =
18 + 32 - 10,75

D = 86,38 kN

Tgs TGX GB

Uploaded by

Copyright:

Available Formats

Tgs TGX GB

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tgs TGX GB

Uploaded by

Copyright:

Available Formats

Guidelines to tting bodies

are registered trademarks of MAN Truck & Bus AG

or sign, acknowledged as the proprietors protected marks.

GENERATION (TGS/TGX) III

6.10.3 Parameterisation of the vehicle electronics

, 2 rear axles, one of which is driven.

6x2/2 Three-axle vehicle with non-steered Pusher leading axle

), one driven rear axle and a steered

) and two driven rear axles

plus Euro 5 with SCR technology.

: Particulate Matter (particle lter)

1.600 at 1.000 - 1.400 rpm D2066LF39

1.600 at 1.000 - 1.400 rpm D2066LF35

tank and fully lled fuel tank

are legally regarded as off-road vehicles as dened by 70/156 EEC

hydraulic system (including relocating pipework) may only be carried out by

. (Installation no. 81.36000.8134).

systems Time maintenance system of Flexible maintenance system.

-BOM, blind fasteners) manufacturers installation instructions

RAS (e.g. all 6x2-4), depending upon the extent of the

RAS trailing axle steering

systems Time maintenance system of Flexible maintenance system.

= Vertical working angle

system in Euro 5 vehicles ESC-419

components on the vehicle overall ESC-420

system(size 9x1.5, PA12-PHL-Y, printed in white,

system dosing module for solo trucks:

system dosing module for tractor units:

and engine coolant pipes.

feed or return pipe.

and coolant pipes ESC-423

system is arranged as follows:

system in Euro 6 vehicles ESC-419a

tank is currently not possible.

system must be adapted correspondingly.

= Frame overhang, in [mm]

fuel and further service ll

GENERATION (TGS/TGX) 100

GENERATION (TGS/TGX) 101

-BOM, blind fasteners) manufacturers installation

GENERATION (TGS/TGX) 102

GENERATION (TGS/TGX) 103

GENERATION (TGS/TGX) 104

GENERATION (TGS/TGX) 105

GENERATION (TGS/TGX) 106

GENERATION (TGS/TGX) 107

GENERATION (TGS/TGX) 108

GENERATION (TGS/TGX) 109

GENERATION (TGS/TGX) 110

GENERATION (TGS/TGX) 111

GENERATION (TGS/TGX) 112

GENERATION (TGS/TGX) 113

GENERATION (TGS/TGX) 114

GENERATION (TGS/TGX) 115

GENERATION (TGS/TGX) 116

GENERATION (TGS/TGX) 117

GENERATION (TGS/TGX) 118

GENERATION (TGS/TGX) 119

GENERATION (TGS/TGX) 120