74 HC 132
74 HC 132
74 HC 132
http://onsemi.com
MARKING
DIAGRAMS
Features
14
A1
14
VCC
B1
13
B4
Y1
12
A4
A2
11
Y4
B2
10
B3
Y2
A3
GND
Y3
SOIC14
D SUFFIX
CASE 751A
HC132G
AWLYWW
1
14
HC
132
ALYW G
G
TSSOP14
DT SUFFIX
CASE 948G
1
FUNCTION TABLE
Inputs
Output
L
L
H
H
L
H
L
H
H
H
H
L
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
74HC132
A1
1
3
B1
A2
2
4
6
B2
A3
Y2
5
Y = AB
9
8
B3
Y1
Y3
10
A4 12
11
B4
Y4
13
PIN 14 = VCC
PIN 7 = GND
ORDERING INFORMATION
Package
Shipping
SOIC14
(PbFree)
TSSOP14*
Device
74HC132DR2G
74HC132DTR2G
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently PbFree.
http://onsemi.com
2
74HC132
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
VCC
*0.5 to )7.0
VIN
*0.5 to )7.0
VOUT
DC Output Voltage
*0.5 to )7.0
*0.5 to VCC )0.5
IIK
*20
mA
IOK
$20
mA
IOUT
$25
mA
ICC
$75
mA
IGND
$75
mA
TSTG
*65 to )150
_C
260
_C
)150
_C
14SOIC
14TSSOP
125
170
_C/W
SOIC
TSSOP
500
450
mW
Output in 3State
High or Low State
TL
TJ
qJA
Thermal Resistance
PD
MSL
Moisture Sensitivity
FR
Flammability Rating
VESD
ILatchup
Level 1
Oxygen Index: 30% 35%
UL 94 V0 @ 0.125 in
u2000
u200
$300
mA
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Tested to EIA/JESD22A114A.
2. Tested to EIA/JESD22A115A.
3. Tested to EIA/JESD78.
4. For high frequency or heavy load considerations, see Chapter 2the ON Semiconductor HighSpeed CMOS Data Book (DL129/D).
Parameter
DC Supply Voltage (Referenced to GND)
DC Input Voltage, Output Voltage (Referenced to GND)
TA
tr, tf
Min
Max
Unit
2.0
6.0
VCC
*55
)125
_C
No Limit
(Note 5)
ns
http://onsemi.com
3
74HC132
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
VCC
Symbol
Parameter
VT+max
Maximum PositiveGoing
Input Threshold Voltage
(Figure 5)
VT+min
Test Conditions
Guaranteed Limit
(V)
*55_C to 25_C
v85_C
v125_C
Unit
VOUT = 0.1 V
|IOUT| v 20 mA
2.0
4.5
6.0
1.5
3.15
4.2
1.5
3.15
4.2
1.5
3.15
4.2
Minimum PositiveGoing
Input Threshold Voltage
(Figure 5)
VOUT = 0.1 V
|IOUT| v 20 mA
2.0
4.5
6.0
1.0
2.3
3.0
0.95
2.25
2.95
0.95
2.25
2.95
VTmax
Maximum NegativeGoing
Input Threshold Voltage
(Figure 5)
2.0
4.5
6.0
0.9
2.0
2.6
0.95
2.05
2.65
0.95
2.05
2.65
VTmin
Minimum NegativeGoing
Input Threshold Voltage
(Figure 5)
2.0
4.5
6.0
0.3
0.9
1.2
0.3
0.9
1.2
0.3
0.9
1.2
VHmax
(Note 7)
Maximum Hysteresis
Voltage
(Figure 5)
2.0
4.5
6.0
1.2
2.25
3.0
1.2
2.25
3.0
1.2
2.25
3.0
VHmin
(Note 7)
Minimum Hysteresis
Voltage
(Figure 5)
2.0
4.5
6.0
0.2
0.4
0.5
0.2
0.4
0.5
0.2
0.4
0.5
VOH
Minimum HighLevel
Output Voltage
2.0
4.5
6.0
1.9
4.4
5.9
1.9
4.4
5.9
1.9
4.4
5.9
4.5
6.0
3.98
5.48
3.84
5.34
3.7
5.2
2.0
4.5
6.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
4.5
6.0
0.26
0.26
0.33
0.33
0.4
0.4
VIN v
VOL
Maximum LowLevel
Output Voltage
VTmin or VT+max
|IOUT| v 4.0 mA
|IOUT| v 5.2 mA
VIN VT+max
|IOUT| v 20 mA
VIN
VT+max
|IOUT| v 4.0 mA
|IOUT| v 5.2 mA
IIN
6.0
$0.1
$1.0
$1.0
mA
ICC
Maximum Quiescent
Supply Current
(per Package)
6.0
2.0
20
40
mA
http://onsemi.com
4
74HC132
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6.0 ns)
VCC
Symbol
Parameter
Guaranteed Limit
(V)
*55_C to 25_C
v85_C
v125_C
Unit
tPLH,
tPHL
2.0
4.5
6.0
125
25
21
155
31
26
190
38
32
ns
tTLH,
tTHL
2.0
4.5
6.0
75
15
13
95
19
16
110
22
19
ns
10
10
10
pF
Cin
9. For propagation delays with loads other than 50 pF, and information on typical parametric values, see the ON Semiconductor HighSpeed
CMOS Data Book (DL129/D).
Typical @ 25C, VCC = 5.0 V
CPD
24
10. Used to determine the noload dynamic power consumption: P D = CPD VCC
Semiconductor HighSpeed CMOS Data Book (DL129/D).
tr
tPHL
tTHL
VCC
tPLH
OUTPUT
DEVICE
UNDER
TEST
GND
90%
50%
10%
pF
TEST POINT
tf
90%
50%
10%
INPUT
A OR B
2f
tTLH
CL*
http://onsemi.com
5
74HC132
4
VHtyp
3
4
5
VCC, POWER SUPPLY VOLTAGE (VOLTS)
VHtyp = (VT + typ) (VT typ)
VH
VIN
VCC
VCC
VH
VT +
VT
VT +
VT
VIN
GND
GND
VOH
VOH
VOUT
VOUT
VOL
VOL
VCC
VOUT
VIN
http://onsemi.com
6
74HC132
PACKAGE DIMENSIONS
SOIC14
CASE 751A03
ISSUE H
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.127
(0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
A
14
P 7 PL
0.25 (0.010)
T
D 14 PL
0.25 (0.010)
T B
DIM
A
B
C
D
F
G
J
K
M
P
R
K
M
R X 45 _
SEATING
PLANE
SOLDERING FOOTPRINT*
7X
7.04
14X
1.52
1
14X
0.58
1.27
PITCH
DIMENSIONS: MILLIMETERS
http://onsemi.com
7
MILLIMETERS
MIN
MAX
8.55
8.75
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.337 0.344
0.150 0.157
0.054 0.068
0.014 0.019
0.016 0.049
0.050 BSC
0.008 0.009
0.004 0.009
0_
7_
0.228 0.244
0.010 0.019
74HC132
PACKAGE DIMENSIONS
TSSOP14
CASE 948G01
ISSUE B
14X K REF
0.10 (0.004)
0.15 (0.006) T U
T U
N
2X
14
L/2
0.25 (0.010)
M
B
U
L
PIN 1
IDENT.
N
F
0.15 (0.006) T U
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE W.
DETAIL E
A
V
K1
J J1
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
SECTION NN
W
C
0.10 (0.004)
T SEATING
PLANE
DETAIL E
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
14X
0.36
14X
1.26
DIMENSIONS: MILLIMETERS
http://onsemi.com
8
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.50
0.60
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN MAX
0.193 0.200
0.169 0.177
0.047
0.002 0.006
0.020 0.030
0.026 BSC
0.020 0.024
0.004 0.008
0.004 0.006
0.007 0.012
0.007 0.010
0.252 BSC
0_
8_
74HC132
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including Typicals must be validated for each customer application by customers technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
http://onsemi.com
9
74HC132/D