Emi Emc
Emi Emc
Emi Emc
Radiated electromagnetic field coupling may be treated as two cases. In the near
field, E and H field coupling are treated separately. In the far field, coupling is
treated as a plane wave coupling.
Some typical external noise sources into a radio receiver include radiated electric
field coupling from: high-voltage power lines, broadcast antennas, communications
transmitters, vehicle ignition systems and electric machinery. Most conducted
coupling from external sources occurs through the ac power lines.
Typical radio interference to other equipment includes radiated electric field coupling
to: TV sets, broadcast receivers, telephone lines, appliances, and communications
receivers. Most conducted coupling to other equipment occurs through the ac power
lines.
The most common methods of noise reduction include proper equipment circuit
design, shielding, grounding, filtering, isolation, separation and orientation, circuit
impedance level control, cable design, and noise cancellation techniques.
Electromagnetic radiation involves electric (E) and magnetic (H) fields. Any
change in the flux density of a magnetic field will produce an electric field change in
time and space (Faraday's Law). This change in an electric field causes another
change in the magnetic field due to the displacement current (Maxwell). A time-
varying magnetic field produces an electric field and a time-varying electric field
results in a magnetic field. This forms the basis of electromagnetic waves and time-
varying electromagnetics (Maxwell's Equations). Wave propagation occurs when
there are two forms of energy and the presence of a change in one leads to a change
in the other. Energy interchanges between electric and magnetic fields as the wave
progresses.
Broadband Emissions - a broadband signal may spread its energy across hundreds
of megahertz or more. The magnitude of broadband radiated emissions is usually
expressed in terms of volts per meter per MHz (V/m/MHz). This type of signal is
composed of narrow pulses having relatively short rise and fall times. Broadband
signals are further divided into random and impulse sources. These may be
transient, continuous or intermittent in occurrence. Examples include unintentional
emissions from communication and radar transmitters, electric switch contacts,
computers, thermostats, motor speed controls, thyratron circuits, ignition systems,
voltage regulators, pulse generators, arc/vapor lamps, and intermittent ground
connections. They may also result from galactic and solar noise, lightning
electromagnetic pulses, and by radio frequency pulses associated with electrostatic
discharges.
EMC Regulations affecting the U.S. are provided primarily by the following three
agencies:
One or more of the following types of EMI/EMC Tests are applicable to commercial
and military electronic equipment as determined by the intended application:
Conducted Emissions (CE), Radiated Emissions (RE), Conducted Susceptibility (CS),
and Radiated Susceptibility (RS). The Emissions Tests (CE & RE) record any
undesirable emissions from the test article. This data is plotted against the applicable
specification limits. The Susceptibility Tests (CS & RS) determine the test article's
ability to operate in the typical operating environment. The test article is exposed to
electromagnetic signals at the levels and frequency ranges required by the applicable
specification.
This web site offers information which may be used to design, evaluate, and trouble-
shoot electronic equipment for EMI, EMC. The site resources include Radio Frequency
Interference (RFI) topics, circuit design guidelines; typical EMI/EMC test descriptions,
EMI/EMC reference documents; document Search Engine access; and EMI/EMC
related links for additional information.
Have you ever wondered why the interference that you receive on the radio communications
bands can sometimes disrupt the intended signals?� Interference probability is based on the
potential power transfer densities involved due to the proximity of equipment and antenna
systems; the various transfer mechanisms, and equipment performance. The electromagnetic
transfer mechanisms may vary depending on modes of operation, propagation conditions, and
other variables.� The propagation paths that exist for signal transfer from the transmitters to a
receiver within the RF environment of a radio communications band can be numerous.�
Antenna-to-antenna coupling parameters may vary depending on antenna gain, directivity, beam
width, side lobes, polarization, separation, propagation conditions of the path (path loss), etc.�
� The receiver characteristics which influence performance include noise, dynamic range,
sensitivity, selectivity (RF, IF), desensitization, adjacent signal susceptibility, intermodulation,
cross modulation and spurious response susceptibility.� Once a particular type of interference is
determined to be likely, any analysis should be limited to its most predominate effects.� The
following types of interference are applicable to Radio Frequency (RF) communications
equipment.
This is defined as undesired signals with frequency components that fall within the receiver�s
RF passband and are translated into the Intermediate Frequency (IF) passband via the mixer
stage.� The interfering signal frequency is equal to the sum of the receiver�s tuned frequency
and one half of the narrowest IF bandwidth.� These signals are amplified and detected through
the same process as the desired signals; therefore, a receiver is very susceptible to these
emissions even at lower levels.�
This is defined as undesired signals with frequency components which fall within or near the
receiver�s RF passband and are translated outside of the IF passband via the mixer stage.�
These signals must be of sufficient amplitude to produce non-linear effects within the receiver�s
RF amplifier or mixer stages.� Some of the resulting non-linear response signals may be
converted to the IF passband frequency via the mixer stage where they are amplified and
detected through the same process as the desired signals.� These become similar to co-
channel interference signals at this point. The undesired emissions which are translated outside
of the IF passband may still pass through the remaining receiver stages, if at high enough levels
to survive the out-of-passband attenuation.� They may then be processed by the detector.�
The predominant response for this case is desensitization.�
Results:� Non linear effects in the RF or mixer stages producing receiver desensitization,
intermodulation and cross modulation.�
This is defined as undesired signals with frequency components that are significantly removed
from the receiver�s RF passband.� High level signals may produce spurious responses in the
receiver if mixed with local oscillator (LO) harmonics to produce a signal falling within the IF
passband.� The spurious responses result from the mixing of an undesired signal with the
receiver�s LO.� The amplitude of these responses is directly proportional to the level of the
undesired signals prior to mixing with the LO.� The spurious responses in a receiver usually
occur at specific frequencies.� Any other out of band signals are attenuated by the IF
selectivity.�
Results:� An undesired response created by the mixing of an undesired signal with the LO.�
The undesired signals which mix with the LO and are capable of being translated to the IF stages
are the spurious response frequencies.� These frequencies and their interference power levels
are a function of the receiver�s susceptibility to these responses.�
The transmitter�s fundamental output signal includes characteristics of the power distribution
over a range of frequencies around the fundamental frequency.� These are determined by the
base-band modulation characteristics and are represented by a modulation envelope function.�
The primary parameter associated with the modulation envelope is the transmitter�s nominal
bandwidth (3dB).� This may be derived from the transmitter modulation characteristics (by
Fourier analysis), measured, or from the manufacturer�s specifications.� The power distribution
in the modulation sidebands may be represented by a modulation envelope function showing the
variation of power with frequency.�
The main concern with a transmitter�s harmonic emissions is the undesired signal outputs which
are harmonically related to the fundamental signal rather than to other oscillator circuits.� The
relative power associated with the harmonic emissions may be modeled using data for the
particular transmitter type.� However, since harmonic output power can vary considerably from
one transmitter to another for the same type and model, it should be represented statistically.�
Harmonic emission models may be derived from statistical summaries of measured data or from
manufacturer�s equipment specifications.� Transmitter spurious emission models for prediction
of frequencies above the fundamental are based on harmonic emission levels.� The modulation
envelope must be represented for harmonics as was done for the fundamental.�
6.0 Transmitter Noise
Transmitter noise includes the output spectrum that is a result of the thermal noise generated in
the driver and final amplifier stages as well as the synthesizer noise from lower level stages.�
This is a broad-band noise; however, it usually does not cover the immediate modulation
sidebands.� The level may be specified as the power per bandwidth as a function of frequency
(dBm/Hz).�
These are the undesired signals that result from the local mixing of a transmitter�s output
emission with that of another transmitter.� The mixing usually occurs in the non-linear circuits of
a transmitter whose antenna receives a high level of RF from another transmitter antenna in close
proximity.� The mixing products are radiated by the transmitter�s antenna as possible co-
channel or adjacent signal interference signals.
1. What is EMI?
A) Electromagnetic Interference (EMI) is defined as electromagnetic energy
from sources external or internal to electrical or electronic equipment that
adversely affects equipment by creating undesirable responses (degraded
performance or malfunctions). EMI can be divided into two classes: continuous
wave (CW) and transient.
2. What is EMC?
A) Electromagnetic Compatibility (EMC) is defined as an electrical system's
ability to perform its specified functions in the presence of electrical noise
generated either internally or externally by other systems. The goal of EMC is
to minimize the influence of electrical noise.
4. What are some basic test categories and their associated requirements?
A) The following EMI Tests are performed as determined by the equipment's
intended application: Conducted Emissions (CE), Radiated Emissions (RE),
Conducted Susceptibility (CS), and Radiated Susceptibility (RS). The
Emissions Tests (CE & RE) record any undesirable emissions from the test
article. This data is plotted against the applicable specification limits. The
Susceptibility Tests (CS & RS) determine the test article's ability to operate in
the typical operating environment. The test article is exposed to
electromagnetic signals at the levels and frequency ranges required by the
applicable commercial or military specification.
5. Where are EMI/EMC tests performed?
A) There are many EMI/EMC testing labs throughout the U.S. and many other
countries. Shielded room test chambers and open area test sites (OATS) may be
used depending on the test requirements document.
7. What is RFI?
A) Radio Frequency Interference (RFI) is considered as part of the EMI
spectrum, with interference signals being within the radio frequency (RF)
range. This term was once used interchangeably with EMI.
9. What is an emitter?
A) In EMI applications, this term applies to unintentional radiators, particularly
those that are the source of interference. Otherwise, the term refers to the
intentional radiators such as transmitter antennas.
Introduction
This information is presented as guidelines to the preliminary design and
development stages of electronic circuits for the purpose of preventing
potential electromagnetic interference (EMI) and electromagnetic compatibility
(EMC) problems.� The tips are representative of good printed circuit board
(PCB) design practices and are recommended as a checklist for evaluating
and selecting EMI/EMC software modeling tools.� The EMI simulation of
circuit boards requires the evaluation of many details such as clock
frequencies, switching rates, rise/fall times, signal harmonics, data transfer
rates, impedances, trace loading and consideration of the types and values of
the various circuit components.� The physical layout of the PC board and its
associated metallic components are important considerations.� Special
attention should be given to the placement and characteristics of signal
source components, vias, traces, pads, board stack-up, shielded enclosures,
connectors and cables.� For example, as signal frequencies and
clock/switching rates increase, PC board trace characteristics can become
similar to those of transmission lines and radiators.�� A PC board trace or
component can become an efficient antenna at a length as small as one
twentieth of a wavelength.�
EMI/EMC problems may be approached at the component, PC board or
enclosure levels.� However, it is much more efficient to deal with these
problems as close to the source or susceptible victim as possible.�
Therefore, it is important to consider these tips as guidelines for PCB design
and layout so that problems may be identified and prevented prior to actual
fabrication of the equipment.
General
(1) EMI controls should be applied at the circuit and box levels prior to
addressing EMI at the interconnected and system levels.
(2) Digital circuits are more likely to be the source of emissions due to the
handling of periodic waveforms and the fast clock/switching rates.� Analog
circuits are more likely to be the susceptible victims due to higher gain functions.
(4) EMI problems involving an active component can be the result of the device's
output transferring the emissions or its input providing the path for
susceptibility.�� However, at high frequencies the active component may
become a direct radiator or receptor of EMI.� Also, the component�s power
and ground connections can provide paths for both emissions and susceptibility.
(5) Although common mode currents are usually small compared to differential
mode currents, they can be the main cause of radiated emissions.
(6) Emissions and susceptibility that are typical in single layer, free wired (using
power and ground traces instead of planes) PC Board design, can be greatly
improved by using multi-layer PC boards with power planes.� High capacitance
between a forward signal and its return path (ground plane) provides
containment of the electric field.� Low inductance of the paths provides for
magnetic flux cancellation.� Although not always realistic in a PCB stack-up
design, a trace should be spaced one dielectric layer away from its associated
return path and the voltage and ground planes should be as closely spaced as
possible.
b. A ground plane can lower the overall ground impedance, thus reducing
high frequency ground bounce.� Also, the impedance between the
ground and voltage planes is lowered at the high frequencies and this
reduces power bus ringing.�
(8) Clocked IC�s with rapid output transitions can be very demanding on voltage
and current distribution components such as the power supply, power bus, and
power planes.� The inductance of the power bus can prevent the rapid energy
transfer needed to meet the quick output transitions and fast rise times.� This
can be improved with the placement of decoupling capacitors at the IC�s power
pins.� The capacitors must be properly selected in their frequency response to
deliver the energy needed at the IC�s output frequency spectrum.� However,
as the number of decoupling paths increase, so do the number of voltage drops
across them and this can result in power bus transients along with the associated
common mode emissions.�� This problem can be minimized with proper
power plane design in the area of the IC�s.� The power plane acts as an
effective high frequency capacitor, and consequently, as an additional energy
source needed for cleaner IC outputs.���
PCB Layout
(1) Use multi-layer PC boards rather than single-layer boards whenever possible.
(2) If a single layer board must be used, a ground plane should be utilized to help
reduce radiation.
(3) Top and bottom ground planes can help reduce radiation from multi-layer
boards by at least 10 dB.
(4) Segmented PC board ground planes are useful for reducing cable radiation
due to common mode currents.
(5) Power and return planes should be located on opposite sides of a multi-layer
PCB.� Effective power planes are low in inductance.� Therefore, any
transients that may develop on the power planes will be at lower levels, resulting
in lower common mode EMI.
(6) Connection of the power planes to high frequency IC power pins should be as
close to the IC pins as possible.� Faster rise times may require connections
directly to the pads of the IC power pins.
(7) Analog and digital circuits are susceptible to interaction when located in close
proximity to each other.� These should be located on different layers of the PC
board whenever possible.� If the circuits must be located on the same layer,
they should be separated into analog and digital areas with proper isolation
layout.
(8) High frequency traces, such as those used for clock and oscillator circuits,
should be contained by two ground planes.� This provides for maximum
isolation.� The reactance of a trace or conductor can easily exceed its dc
resistance as frequency increases.� If this trace is run close to its ground plane,
the inductance can be reduced by about one third.��
(9) Additional EMI preventive measures for clock/oscillator traces include the
utilization of guard traces grounded to the ground plane at several locations. The
shielding of clock and oscillator components with foil or small metallic enclosures
may also be needed.
(10) Overall circuit cross-talk increases by a factor of two whenever the clock rate
is doubled.�� EMI radiation and cross-talk may be reduced by minimizing the
PC board trace height above the ground plane.�
(11) PC board edge radiation may be the result of traces being located too close
to the board edge.� This can be minimized by keeping traces at a distance of at
least 3 times the board thickness away from the board edge.�
(2) Capacitors may be used for signal filtering and power source decoupling
within their high frequency performance characteristics.� However, their internal
and external inductance can limit performance at high frequencies.� Ceramic
capacitors are recommended for the high frequencies, particularly those in the
GHz range.� A capacitor providing a reactance of less than 1 Ohm at the
frequency of concern should suffice.�� Capacitor lead and trace lengths must
be short at the high frequencies in order to prevent the addition of inductive
reactance.
(3) PC board bypass capacitors used at high frequencies (greater than 100 MHz)
should utilize surface mount technology (SMT) with vias close enough to the
mounting pad to minimize or eliminate the traces.� The via holes should be
large (greater than .035 inch in diameter) and the PC board should be thin
enough to bring power and ground planes near the body of the capacitor (less
than .030 inch thick).�� Proper design layout of the bypass capacitors can
greatly reduce the power and ground circuit noise by lowering the overall
effective inductance of the capacitors.
(4) Wire wound ferrite inductors may be used for EMI emissions and immunity
filtering at lower RF frequencies.� These can supply from about 1 microhenry to
1 millihenry of inductance.�� However, they can become a capacitor above
their resonant frequency and are useless in the most common EMI frequency
range of 50 MHz to 500 MHz.� Ferrites and ferrite beads are recommended for
higher frequency applications where they become lossy and act more like a
resistor.� Select a ferrite impedance of about 100 to 600 Ohms at the
frequencies of concern.
(5) Shielded I/O cable connectors equipped with bypass capacitors or filter pins
should be used whenever possible.
(6) I/O filters should be inside of the I/O connector (as with filter pins) instead of
on the PC board.
(7) I/O bypass capacitors should be mounted at the I/O connector instead of on
the PC board.
(8) I/O ferrites should be mounted inside of the I/O connector instead of on the
PC board.
(9) A snap-on ferrite bead at the I/O cable connector can provide 3 to 5 dB of
common mode absorption.
(11) Ferrite beads are available in high-Q resonant and low-Q non-resonant
(absorptive) types.� The low-Q beads are recommended for digital circuits and
filtering applications.���
(12) External cable or I/O connector filters can provide for a common mode
rejection of greater than 10 dB.
(1) Cables should be grouped according to their function such as power, analog,
digital, and RF.
(2) Separate connector assemblies should be used for analog and digital signals.
(3) Analog and digital connectors should be located as far apart as possible.
(4) Analog and digital signal pins should be separated by unused grounded pins
when sharing the same I/O connector.
(5) Individual pins should be used inside the I/O connector for each signal return
so that all return circuits remain separated.
(6) Connector crosstalk may be reduced by using separate power and ground
pins for each signal and by reducing the circuit�s loading and current
flow.���
(7) Cable shields should be grounded to equipment housing at the I/O points.
(8) Shielded I/O cables are most effective if grounded at both ends.
(9) Cable common mode currents should be removed at the equipment�s metal
housing prior to internal connections.
(10) Cables should be routed close to ground planes, shielded structures, and
cable trays.
Grounding
Introduction
It is important that software analysis tools address the following major problem
areas of PCB design. The fast clock speeds and rapid edge rates needed in
many PCB designs require proper management of board level design, layout and
signal interconnects in order to minimize EMI. High speed switching has the
capability of producing electromagnetic waves that generate resonance,
power/ground bounce, simultaneous switching noise, reflections, and coupling
between traces and power/ground planes. The effects of improper ground plane
design can hinder the performance of high-speed clocks and synchronous
busses. Most major sources of emissions appear due to signal related
parameters such as the clock or pulse repetition frequency, signal edge rate, and
signal ringing due to impedance mismatches. The greater the performance
characteristics of semiconductor components in a circuit design, the more
electromagnetic interference that may occur. Therefore, the design of a PCB
must eliminate any antennas that are capable of radiating electromagnetic
energy. Loops of signal and the corresponding ground return lines carrying high
frequency signals must be minimized.
Single layer boards are much more likely to cause EMI problems than multi-layer
boards. Two layer and four layer boards generally have a minimal of radiation in
comparison, if properly designed. A common problem at the system level is the
radiation due to cables interconnecting the PCB with external support equipment
or peripherals such as displays, external processors, and keyboards. In many
cases, there may be only one ground wire between the PCB and external
peripherals. The inductive ground conductor provides the return for all of the RF
energy carried to the external equipment through the multiple wiring. Any
impedance in the ground wire will prevent some of the RF energy from returning
to the PCB through the normal ground path. This radiated RF energy may be
coupled back through undesirable paths including some of the external
equipment. The emissions may cause EMI in other parts of the system, as well
as to EMI/EMC testing facilities.
The PCB design techniques for addressing susceptibility are somewhat similar to
those for emissions. Loop areas of greater size will tend to receive larger signal
levels. They are also capable of radiating EMI at higher levels. Ground bounce,
or common impedance coupling of circuits, can cause circuit operational failure
and the associated EMI. For example, if a ground path has high impedance, it
may cause a driving circuit�s reference voltage to shift, resulting in its input to
the microcomputer to be outside of the device�s required switching range for
normal operation.