g0440 M
g0440 M
2 HP & 3 HP
CYCLONE DUST COLLECTORS
OWNER'S MANUAL
(For models manufactured since 03/12)
COPYRIGHT APRIL, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED OCTOBER, 2013 (TS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR7027 PRINTED IN TAIWAN
Model G0441 Shown
With Optional Stand
V6.10.13
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injuryincluding amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
Lead from lead-based paints.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents
INTRODUCTION ............................................... 2
Machine Description ...................................... 2
Contact Info.................................................... 2
Manual Accuracy ........................................... 2
Identification ................................................... 3
G0440 Machine Data Sheet .......................... 4
G0441 Machine Data Sheet .......................... 6
SECTION 1: SAFETY ....................................... 8
Safety Instructions for Machinery .................. 8
Additional Safety for Dust Collectors ........... 10
SECTION 2: POWER SUPPLY ...................... 11
Availability .................................................. 11
Full-Load Current Rating ........................... 11
Circuit Requirements ................................. 11
G0440 Circuit Requirements ..................... 11
G0441 Circuit Requirements ..................... 11
Connection Type ....................................... 12
Grounding Instructions .............................. 12
Extension Cords ........................................ 12
SECTION 3: SETUP ....................................... 13
Unpacking .................................................... 13
Needed for Setup ......................................... 13
G0440 Inventory .......................................... 14
G0441 Inventory .......................................... 15
Site Considerations ...................................... 16
Wall Mounting .............................................. 17
Materials Needed for Standard Wood
Framed Walls ............................................ 17
Materials Needed for Concrete/Masonry
Wall ............................................................ 18
Assembly ..................................................... 19
Test Run ...................................................... 25
SECTION 4: DESIGNING THE SYSTEM ....... 26
General ........................................................ 26
Duct Material ................................................ 26
Metal Duct ................................................. 27
Flexible Duct .............................................. 27
System Design ............................................. 28
Step 1. Decide Who Will Design ............... 28
Step 2. Sketch Your Shop Layout ............. 28
Step 3. Sketch a Basic Duct Layout .......... 28
Step 4. Determine Required CFMs ........... 29
Determining Main Line Duct Size .............. 30
Determining Branch Line Duct Size .......... 30
Planning Drop Downs ................................ 30
Multiple Dust Ports .................................... 31
Two Machines on Same Branch Line ....... 31
Calculating Duct Resistance ..................... 31
Example Materials List .............................. 33
System Grounding ....................................... 34
SECTION 5: OPERATIONS ........................... 35
Remote Control ............................................ 35
General ........................................................ 35
SECTION 6: ACCESSORIES ......................... 36
SECTION 7: MAINTENANCE ......................... 38
Emptying Drum ............................................ 38
Cleaning Filter .............................................. 38
Rinsing Filter ................................................ 38
Removing/Replacing Filter ........................... 39
SECTION 8: SERVICE ................................... 41
Troubleshooting ........................................... 41
SECTION 9: WIRING ...................................... 42
Wiring Safety Instructions ............................ 42
G0440 Wiring Diagram ................................ 43
G0441 Wiring Diagram ................................ 44
G0440/G0441 Electrical Components ......... 45
SECTION 10: PARTS ..................................... 46
G0440 Main ................................................. 46
G0441 Main ................................................. 48
WARRANTY AND RETURNS ........................ 53
-2-
Model G0440/G0441 (Mfg. Since 03/12)
The Model G0440/G0441 is a 2-stage cyclone
wood dust collector capable of collecting dust
from multiple machines running simultaneously.
Cyclonic action separates the heavy dust and
chips from the fine particles and drops them into
the steel collection drum. Any remaining fine dust
travels past the impeller and is trapped by the
pleated cartridge filter. With the use of the cable
and pulley system on the outside of the filter
assembly, the caked dust is brushed down into
the collection bag.
The machine is controlled by the remote magnetic
switch mounted to it or by the IR remote control-
lereach control includes timer options.
INTRODUCTION
Machine Description
We are proud to provide a high-quality owners
manual with your new machine!
We made every effort to be exact with the instruc-
tions, specifications, drawings, and photographs
contained inside. Sometimes we make mistakes,
but our policy of continuous improvement also
means that sometimes the machine you receive
will be slightly different than what is shown in
the manual.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused about a procedure, check our website
for an updated version. We post current manuals
and manual updates for free on our website at
www.grizzly.com.
Alternatively, you can call our Technical Support
for help. Before calling, please write down the
Manufacture Date and Serial Number stamped
into the machine ID label (see below). This infor-
mation helps us determine if updated documenta-
tion is available for your machine.
Manufacture Date
Serial Number
Manual Accuracy
We stand behind our machines. If you have
any questions or need help, use the information
below to contact us. Before contacting, please get
the serial number and manufacture date of your
machine. This will help us help you faster.
Grizzly Technical Support
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Email: techsupport@grizzly.com
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: manuals@grizzly.com
Contact Info
Model G0440/G0441 (Mfg. Since 03/12)
-3-
Identification
To reduce the risk of
serious injury when using
this machine, read and
understand this entire
manual before beginning
any operations.
Figure 1. Identification (Model G0441 shown with optional stand).
Canister
Filter Assembly
Vacuum
Hose
Collection
Drum
Optional
Stand
Remote
Magnetic Switch
Inlet
Port
Blower
Housing
Motor
-4-
Model G0440/G0441 (Mfg. Since 03/12)
The information contained herein is deemed accurate as of 11/4/2013 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 3 Model G0440
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 To Order Call: (800) 523-4777 Fax #: (800) 438-5901
MODEL G0440 2 HP CYCLONE DUST COLLECTOR
Product Dimensions:
Weight.............................................................................................................................................................. 287 lbs.
Width (side-to-side) x Depth (front-to-back) x Height............................................................... 59 x 37-3/4 x 93-1/4 in.
Footprint (Length x Width)..................................................................................................................... 37-3/4 x 59 in.
Shipping Dimensions:
Carton #1
Type........................................................................................................................................... Cardboard Box
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 314 lbs.
Length x Width x Height............................................................................................................. 54 x 28 x 35 in.
Must Ship Upright......................................................................................................................................... Yes
Carton #2
Type........................................................................................................................................... Cardboard Box
Content......................................................................................................................................... Canister Filter
Weight...................................................................................................................................................... 38 lbs.
Length x Width x Height............................................................................................................. 49 x 18 x 18 in.
Must Ship Upright.......................................................................................................................................... No
Electrical:
Power Requirement........................................................................................................... 220V, Single-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 220V
Full-Load Current Rating........................................................................................................................................ 14A
Minimum Circuit Size.............................................................................................................................................. 20A
Connection Type......................................................................................................................... Permanent Hardwire
Switch Type......................................................................... Remote Control Magnetic Switch w/Overload Protection
Motors:
Main
Type.................................................................................................. TEFC Capacitor-Start Induction (Class F)
Horsepower................................................................................................................................................ 2 HP
Phase............................................................................................................................................ Single-Phase
Amps............................................................................................................................................................ 14A
Speed................................................................................................................................................ 3450 RPM
Power Transfer ............................................................................................................................... Direct Drive
Bearings..................................................................................................... Shielded & Permanently Lubricated
Model G0440/G0441 (Mfg. Since 03/12)
-5-
The information contained herein is deemed accurate as of 11/4/2013 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 2 OF 3 Model G0440
Main Specifications:
Operation
Dust Collector Type.......................................................................................................... Two-Stage (Cyclone)
Approved Dust Types................................................................................................................................ Wood
Filter Type............................................................................................................................... Pleated Cartridge
Airflow Capacity............................................................................................................ 1354 CFM @ 2.5 in. SP
Max Static Pressure (at 0 CFM)............................................................................................................. 10.4 in.
Main Inlet Size............................................................................................................................................. 7 in.
Inlet Adapter Included.................................................................................................................................... No
Machine Collection Capacity At One Time....................................................................................... 3 Machines
Maximum Material Collection Capacity................................................................................................ 4.7 cu. ft.
Filtration Rating............................................................................................................................ 0.2 2 Micron
Filter Surface Area................................................................................................................................ 96 sq. ft.
Bag Information
No of Lower Bags............................................................................................................................................. 1
Lower Bag Diameter............................................................................................................................ 15-3/4 in.
Canister Information
No of Canister Filters........................................................................................................................................ 1
Canister Filter Diameter....................................................................................................................... 15-3/4 in.
Canister Filter Length.......................................................................................................................... 46-3/4 in.
Collection Drum Size......................................................................................................................... 35 Gallons
Impeller Information
Impeller Type...................................................................................................................................... Radial Fin
Impeller Size........................................................................................................................................ 14-1/2 in.
Construction
Lower Bag...................................................................................................................................... Clear Plastic
Canister............................................................................................................................ Spun Bond Polyester
Frame....................................................................................................................... Steel Sheet Metal (14 ga.)
Impeller....................................................................................................................................................... Steel
Paint........................................................................................................................................... Powder Coated
Blower Housing......................................................................................................................... 11 Gauge Steel
Body.......................................................................................................................................... 14 Gauge Steel
Collection Drum..................................................................................................................................... Steel
Other
Optional Stand......................................................................................................................................... H7499
Other Specifications:
Country Of Origin ............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time ............................................................................................................. 3 Hours
Serial Number Location .................................................................................................................................. ID Label
Sound Rating ............................................................................................................................................. 83 85 dB
ISO 9001 Factory .................................................................................................................................................... No
CSA Certified ......................................................................................................................................................... Yes
Awards ....................................................................................................... American Woodworker Editor's Pick 2006
-6-
Model G0440/G0441 (Mfg. Since 03/12)
G0441 Machine Data Sheet
The information contained herein is deemed accurate as of 11/6/2013 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 3 Model G0441
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 To Order Call: (800) 523-4777 Fax #: (800) 438-5901
MODEL G0441 3 HP CYCLONE DUST COLLECTOR
Product Dimensions:
Weight.............................................................................................................................................................. 347 lbs.
Width (side-to-side) x Depth (front-to-back) x Height............................................................. 60-1/4 x 38-1/2 x 109 in.
Footprint (Length x Width)............................................................................................................... 32-7/8 x 32-7/8 in.
Shipping Dimensions:
Carton #1
Type........................................................................................................................................... Cardboard Box
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 354 lbs.
Length x Width x Height............................................................................................................. 53 x 28 x 34 in.
Must Ship Upright......................................................................................................................................... Yes
Carton #2
Type........................................................................................................................................... Cardboard Box
Content......................................................................................................................................... Canister Filter
Weight...................................................................................................................................................... 46 lbs.
Length x Width x Height............................................................................................................. 49 x 22 x 22 in.
Must Ship Upright.......................................................................................................................................... No
Electrical:
Power Requirement........................................................................................................... 220V, Single-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 220V
Full-Load Current Rating........................................................................................................................................ 22A
Minimum Circuit Size.............................................................................................................................................. 40A
Connection Type.......................................................................................................................... Permanent Hardwire
Switch Type......................................................................... Remote Control Magnetic Switch w/Overload Protection
Motors:
Main
Type.................................................................................................. TEFC Capacitor-Start Induction (Class F)
Horsepower................................................................................................................................................ 3 HP
Phase............................................................................................................................................ Single-Phase
Amps............................................................................................................................................................ 22A
Speed................................................................................................................................................ 3450 RPM
Power Transfer ............................................................................................................................... Direct Drive
Bearings..................................................................................................... Shielded & Permanently Lubricated
Model G0440/G0441 (Mfg. Since 03/12)
-7-
The information contained herein is deemed accurate as of 11/4/2013 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 2 OF 3 Model G0441
Main Specifications:
Operation
Dust Collector Type.......................................................................................................... Two-Stage (Cyclone)
Approved Dust Types................................................................................................................................ Wood
Filter Type............................................................................................................................... Pleated Cartridge
Airflow Capacity............................................................................................................ 1654 CFM @ 2.0 in. SP
Max Static Pressure (at 0 CFM)............................................................................................................. 14.2 in.
Main Inlet Size............................................................................................................................................. 8 in.
Inlet Adapter Included.................................................................................................................................... No
Machine Collection Capacity At One Time....................................................................................................... 3
Maximum Material Collection Capacity................................................................................................ 7.4 cu. ft.
Filtration Rating............................................................................................................................ 0.2 2 Micron
Filter Surface Area.............................................................................................................................. 113 sq. ft.
Bag Information
No of Lower Bags............................................................................................................................................. 1
Lower Bag Diameter............................................................................................................................ 19-3/4 in.
Canister Information
No of Canister Filters........................................................................................................................................ 1
Canister Filter Diameter................................................................................................................... 19-11/16 in.
Canister Filter Length.......................................................................................................................... 46-1/4 in.
Collection Drum Size......................................................................................................................... 55 Gallons
Impeller Information
Impeller Type...................................................................................................................................... Radial Fin
Impeller Size........................................................................................................................................ 15-1/2 in.
Construction
Lower Bag...................................................................................................................................... Clear Plastic
Canister............................................................................................................................ Spun Bond Polyester
Frame....................................................................................................................... Steel Sheet Metal (14 ga.)
Impeller....................................................................................................................................................... Steel
Paint........................................................................................................................................... Powder Coated
Blower Housing......................................................................................................................... 11 Gauge Steel
Body.......................................................................................................................................... 14 Gauge Steel
Collection Drum..................................................................................................................................... Steel
Other
Optional Stand......................................................................................................................................... H7509
Other Specifications:
Country Of Origin ............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time ............................................................................................................. 3 Hours
Serial Number Location .................................................................................................................................. ID Label
Sound Rating ............................................................................................................................................. 83 85 dB
ISO 9001 Factory .................................................................................................................................................... No
CSA Certified ......................................................................................................................................................... Yes
Awards ....................................................................................................... American Woodworker Editor's Pick 2006
-8-
Model G0440/G0441 (Mfg. Since 03/12)
ELECTRICAL EQUIPMENT INJURY RISKS. You
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
DISCONNECT POWER FIRST. Always discon-
nect machine from power supply BEFORE making
adjustments, changing tooling, or servicing machine.
This prevents an injury risk from unintended startup
or contact with live electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are not approved safety glasses.
OWNERS MANUAL. Read and understand this
owners manual BEFORE using machine.
TRAINED OPERATORS ONLY. Untrained oper-
ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized useespecially
around children. Make workshop kid proof!
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin-
ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
SECTION 1: SAFETY
Model G0440/G0441 (Mfg. Since 03/12)
-9-
WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips, which could cause loss of work-
piece control.
HAZARDOUS DUST. Dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material,
and always wear a NIOSH-approved respirator to
reduce your risk.
HEARING PROTECTION. Always wear hear-
ing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
INTENDED USAGE. Only use machine for its
intended purpose and never make modifications
not approved by Grizzly. Modifying machine or
using it differently than intended may result in
malfunction or mechanical failure that can lead to
serious personal injury or death!
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.
GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly.
FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement dur-
ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owners manual or the manufacturer for rec-
ommended accessories. Using improper acces-
sories will increase the risk of serious injury.
UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
CHECK DAMAGED PARTS. Regularly inspect
machine for any condition that may affect safe
operation. Immediately repair or replace damaged
or mis-adjusted parts before operating machine.
MAINTAIN POWER CORDS. When disconnect-
ing cord-connected machines from power, grab
and pull the plugNOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intend-
ed operation, stop using the machine! Contact our
Technical Support at (570) 546-9663.
-10-
Model G0440/G0441 (Mfg. Since 03/12)
Additional Safety for Dust Collectors
INTENDED USE. This dust collector is designed
for collecting wood dust and chips from wood-
working machines. DO NOT use it to collect
metal, dirt, drywall, asbestos, lead paint, silica, liq-
uids, aerosols, biohazards, or explosive materials.
Collecting the wrong materials can result in seri-
ous inhalation hazards, fire, or machine damage.
HAZARDOUS DUST. Dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material,
and always wear a NIOSH-approved respirator to
reduce your risk.
WEAR A RESPIRATOR. Fine dust that is too
small to be caught in the filter will be blown into
the ambient air during operation. To reduce your
risk of respiratory damage from this fine dust,
always wear a NIOSH approved respirator during
operation and for a short time after. Also, never
collect dust from any type of hazardous material.
IMPELLER HAZARDS. All objects collected by
this machine can strike the rotating impeller. DO
NOT place hands, hair, clothing, or tools near the
open inlet during operation. The powerful suction
could easily pull them into the impeller, which will
cause serious personal injury or damage to the
machine. Always keep small animals and children
away from open dust collection inlets.
DISCONNECTING POWER SUPPLY. Turn the
switch OFF, disconnect the dust collector from
the power supply, and allow the impeller to come
to a complete stop before leaving the machine
unattended or doing any service, cleaning, main-
tenance, or adjustments.
REGULAR CLEANING. Regularly check/empty
the collection bags or drum to avoid the buildup
of fine dust that can increase the risk of fire. Make
sure to regularly clean the surrounding area where
the machine is operatedexcessive dust buildup
on overhead lights, heaters, electrical panels, or
other heat sources will increase the risk of fire.
SUSPENDED DUST PARTICLES AND IGNITION
SOURCES. DO NOT operate the dust collector in
areas where explosion risks are high. Areas of
high risk include, but are not limited to, areas near
pilot lights, open flames, or other ignition sources.
AVOIDING SPARKS. Avoid collecting steel frag-
ments or stones. These items can produce sparks
when they strike the impeller, which can smol-
der in wood dust for a long time before a fire is
detected. If you accidentally cut into wood con-
taining tramp metal (nails, staples, spikes, etc.),
immediately turn OFF the dust collector, discon-
nect it from power, and wait for the impeller to
stopthen empty the collection container into an
approved airtight metal container.
OPERATING LOCATION. To reduce respira-
tory exposure to fine dust, locate permanently
installed dust collectors away from the working
area or in another room. DO NOT place the dust
collector where it can be exposed to rain or mois-
tureexposure to water creates a shock hazard
and will reduce the life of the machine.
FIRE SUPPRESSION. Only operate the dust col-
lector in locations that contain a fire suppression
system or have a fire extinguisher nearby.
STATIC ELECTRICITY. Plastic dust lines gener-
ate high amounts of static electricity as dust chips
pass through them. Although rare, sparks caused
by static electricity can cause explosions or fire.
To reduce this risk, make sure all dust lines are
thoroughly grounded by using a grounding wire.
EMPTYING DUST. When emptying dust from the
collection container, wear a respirator and safety
glasses. Empty dust away from ignition sources
and into an approved container.
DUST ALLERGIES. Dust from certain woods will
cause an allergic reaction. Always make sure you
know what type of wood dust you are exposed to
in the event that this happens.
Model G0440/G0441 (Mfg. Since 03/12)
-11-
SECTION 2: POWER SUPPLY
Availability Circuit Requirements
Before installing the machine, consider the avail-
ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrican or
qualified service personnel in accordance with all
applicable codes and standards.
G0440 Full-Load Current Rating ....... 14 Amps
G0441 Full-Load Current Rating ....... 22 Amps
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
Note: The circuit requirements listed in this man-
ual apply to a dedicated circuitwhere only one
machine will be running at a time. If this machine
will be connected to a shared circuit where mul-
tiple machines will be running at the same time,
consult a qualified electrician to ensure that the
circuit is properly sized for safe operation.
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup-
ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
G0440 Circuit Requirements
Nominal Voltage .............................. 220V/240V
Cycle ..........................................................60 Hz
Phase ........................................... Single-Phase
Circuit Rating ...................................... 20 Amps
G0441 Circuit Requirements
Nominal Voltage .............................. 220V/240V
Cycle ..........................................................60 Hz
Phase ........................................... Single-Phase
Circuit Rating ...................................... 40 Amps
This machine is prewired to operate on a 220V
power supply circuit that has a verified ground and
meets the following requirements:
This machine is prewired to operate on a 220V
power supply circuit that has a verified ground and
meets the following requirements:
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over-
loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the requirements in the following section.
Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power
supply.
-12-
Model G0440/G0441 (Mfg. Since 03/12)
Extension Cords
Since this machine must be permanently con-
nected to the power supply, an extension cord
cannot be used.
Connection Type
Figure 1. Typical setup of a permanently
connected machine.
Power
Source
Locking
Disconnect Switch
Machine
Ground Ground
Conduit Conduit
A permanently connected (hardwired) power sup-
ply is typically installed with wires running through
mounted and secured conduit. A disconnecting
means, such as a locking switch (see following
Figure), must be provided to allow the machine
to be disconnected (isolated) from the power
supply when required. This installation must be
performed by an electrician in accordance with all
applicable electrical codes and ordinances.
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.
Grounding Instructions
In the event of a malfunction or breakdown,
grounding provides a path of least resistance
for electrical current to reduce the risk of electric
shock. A permanently connected machine must
be connected to a grounded metal permanent wir-
ing system; or to a system having an equipment-
grounding conductor. All grounds must be verified
and rated for the electrical requirements of the
machine. Improper grounding can increase the
risk of electric shock!
Model G0440/G0441 (Mfg. Since 03/12)
-13-
Wear safety glasses dur-
ing the entire setup pro-
cess!
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
SECTION 3: SETUP
This machine and its com-
ponents are very heavy.
Get lifting help or use
power lifting equipment
such as a forklift to move
heavy items.
The following are needed to complete the setup
process, but are not included with your machine:
Description Qty
Assistants for Lifting Help ........................... 2
Optional Power Lifting Equipment .............. 1
Wrench or Socket
1
2" ................................. 2
Wrench or Socket
9
16" ................................ 2
Phillips Screwdriver #2 ............................... 1
Mounting Hardware (Page 18) ... As Needed
Medium-Strength Thread Locking
Compound ........................................ 1 Bottle
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover any damage, please call us immediately
at (570) 546-9663 for advice.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
Unpacking
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
Needed for Setup
-14-
Model G0440/G0441 (Mfg. Since 03/12)
G0440 Inventory
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Inventory (Figure 2) Qty
A. Intake Cylinder ........................................... 1
B. Cyclone Funnel .......................................... 1
C. Intake Barrel ............................................... 1
D. Canister/Drum Collection Bags ......... 1 Each
E. Gray Flexible Hose 7" X 32" ...................... 1
F. Motor/Blower Housing Assembly ............... 1
G. Collection Drum Lid .................................... 1
H. Collection Drum .......................................... 1
I. Collection Drum Seal ................................. 1
J. Clear Flexible Hose 9" x 8" ........................ 1
K. Hose Clamps 9" ......................................... 2
L. Outlet Port .................................................. 1
M. Filter L-Braces ............................................ 2
N. Foam Tape Roll 3 x 6mm .......................... 1
O. Hose Clamps 7" ......................................... 3
P. Hardware Box
Phillips Head Screws #10-24 x
3
8" .......... 6
Hex Nuts #10-24 ..................................... 6
Drum Latches ......................................... 3
Roll of Foam Tape 3 x 15mm ................. 1
Q. Hardware Box
Hex Bolts
5
16"-18 x 1" ............................ 22
Hex Bolts
5
16"-18 x
3
4" ........................... 24
Flat Washers
5
16" .................................. 64
Fender Washers
5
16" ............................... 4
Hex Nuts
5
16"-18 .................................... 22
R. Hardware Box
Casters ................................................... 4
Hex Nuts
3
8"-16 ....................................... 4
Lock Washers
3
8" .................................... 4
Flat Washers
3
8" ..................................... 8
S. Wall Mount Brace ....................................... 1
T. Barrel Gaskets ............................................ 2
U. Brace Gaskets ............................................ 2
V. Outlet Gasket ............................................. 1
W. Canister Filter Assembly ............................ 1
X. Hose Clamps 1
1
4" ...................................... 2
Y. Vacuum Hose 1
1
4" x 98" ............................ 1
Z. Collection Drum Vacuum Ring ................... 1
AA. Cyclone Vacuum Tube ............................... 1
F
C
B
A
D
E
L
J
I
G
H
N
Q
P
R
S
T
U
V
Figure 2. Model G0440 inventory.
K
M
O
W
X
Y
Z
AA
Model G0440/G0441 (Mfg. Since 03/12)
-15-
G0441 Inventory
The following is a description of the main compo-
nents shipped with your machine. Lay the compo-
nents out to inventory them.
Inventory: (Figure 3) Qty
A. Intake Cylinder ........................................... 1
B. Cyclone Funnel .......................................... 1
C. Intake Barrel ............................................... 1
D. Canister/Drum Collection Bags ......... 1 Each
E. Gray Flexible Hose 8" x 20" ....................... 1
F. Motor/Blower Housing Assembly ............... 1
G. Upper Collection Drum ............................... 1
H. Muffler ........................................................ 1
I. Gray Flexible Hose 8" x 5" ......................... 1
J. Lower Collection Drum ............................... 1
K. Clear Flexible Hose 9" x 13"....................... 1
L. Hose Clamps 9" ......................................... 2
M. Collection Drum Lid .................................... 1
N. Collection Drum Seal ................................. 1
O. Outlet Port .................................................. 1
P. Filter L-Braces ............................................ 2
Q. Foam Tape Roll 3 x 6mm .......................... 1
R. Hose Clamps 8" ......................................... 5
S. Hardware Box
Phillips Head Screws #10-24 x
3
8" ........ 12
Hex Nuts #10-24 ................................... 12
Drum Latches ......................................... 3
Roll of Foam Tape 3 x 15mm ................. 1
T. Hardware Box
Hex Bolts
5
16"-18 x 1" ............................ 24
Hex Bolts
5
16"-18 x
3
4" ........................... 24
Flat Washers
5
16" .................................. 68
Fender Washers
5
16" ............................... 4
Hex Nuts
5
16"-18 .................................... 24
U. Hardware Box
Casters ................................................... 4
Hex Nuts
3
8"-16 ....................................... 4
Lock Washers
3
8" .................................... 4
Flat Washers
3
8" ..................................... 8
V. Wall Mount Brace ....................................... 1
W. Barrel Gaskets ............................................ 2
X. Brace Gaskets ............................................ 2
Y. Outlet Gasket ............................................. 1
Z. Canister Filter Assembly ............................ 1
AA. Hose Clamps 1
1
4" ...................................... 2
AB. Vacuum Hose 1
1
4" x 98" ............................ 1
AC. Collection Drum Vacuum Ring ................... 1
AD. Cyclone Vacuum Tube ............................... 1
F
C
B
A
D
E
L
J
I
G
H
N
Q
P
R
S
T
U
V
Figure 3. Model G0441 inventory.
K
M
O
W
X
Y
Z
AA
AB
AC
AD
-16-
Model G0440/G0441 (Mfg. Since 03/12)
Site Considerations
Weight Load
Refer to the Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest work-
piece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the main-
tenance and service described in this manual.
See below for required space allocation.
Physical Environment
The physical environment where the machine is
operated is important for safe operation and lon-
gevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemi-
cals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41104F; the relative humidity
range exceeds 2095% (non-condensing); or the
environment is subject to vibration, shocks, or
bumps.
Electrical Installation
Place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals,
or other hazards. Make sure to leave access to
a means of disconnecting the power source or
engaging a lockout/tagout device, if required.
Lighting
Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.
Figure 4. Minimum working clearances.
27"
55"
27"
75"
87"
33"
Model G0440/G0441 (Mfg. Since 03/12)
-17-
Before mounting, make sure you locate your dust
collector away from any open flames or potential
ignition sources, as fine dust can easily ignite.
If you are mounting your dust collector to a wood
framed wall, you must build and install the wall
mounting boards described below to support the
heavy weight of the dust collector.
If you are mounting your dust collector to a con-
crete or masonry wall, skip to Page 18.
Materials Needed for Standard Wood
Framed Walls
2x12 Board 36" Long for Wall Mounting ..... 1
2x6 Board 36" Long for Wall Mounting ...... 1
Level 4' ....................................................... 1
Pencil .......................................................... 1
Measuring Tape .......................................... 1
Lag Bolts
3
8" x 5" (board/wall) .................. 16
Flat Washers
3
8" (board/wall) ................... 16
Lag Bolts
1
2" x 2" (machine/board) ........... 8*
Flat Washers
1
2" (machine/board) ............ 8*
Drill ............................................................. 1
Drill Bit
1
4" (for
3
8" predrill) .......................... 1
Drill Bit
3
8" (for
1
2" predrill) ......................... 1
Stud Finder ................................................. 1
*Two of these fastener sets will be used
in mounting the intake barrel brace dur-
ing assembly.
To mount the motor/impeller housing to a
wood framed wall:
1. Secure the wall mounting boards to your wall,
using the applicable layout diagrams for your
machine and wall type (see Figures 56).
Wall Mounting
81
3
4"
36"
3
1
2"
3
1
2"
12
1
2"
Ground
Wall Stud Wall Stud Wall Stud
2x12 Board
2x6 Board
= Lag Bolts, Countersunk
= Lag Bolts
Wood Framed Walls, G0440
Figure 5. G0440 wall mounting board layout.
81
3
4"
or
97
1
8"
for
Double
Barrel
36"
12
1
2"
Ground
Wall Stud Wall Stud Wall Stud
2x12 Board
2x6 Board
= Lag Bolts, Countersunk
= Lag Bolts
Wood Framed Walls, G0441
3
1
2"
3
1
2"
Figure 6. G0441 wall mounting board layout.
-18-
Model G0440/G0441 (Mfg. Since 03/12)
2. Copy the mounting hole layout pattern from
the motor housing (see Figures 78) to your
wall mounting board, making sure the Top
Row Mounting Hole Height is correct for
your dust collector.
Use these measurements for hole
placement when mounting the
Model G0441.
Single-Barrel Top Row
Mounting Hole Height = 80"
Double-Barrel Top Row
Mounting Hole Height = 95"
20"
10" 10"
G0441 Motor Housing 7
3
4"
80"
or
95
5
8"
Floor
0.55"
Figure 8. G0441 wall mounting layout.
Use these measurements for hole
placement when mounting the
Model G0440.
Top Row Mounting Hole Height = 80"
20
1
2"
10
1
4"
G0440 Motor Housing 7
3
4"
80"
Floor
0.55"
10
1
4"
Figure 7. G0440 wall mounting layout.
3. Tighten
1
2" lag bolts into the mounting loca-
tions so they do not poke out more than
1
2"
from the mounting board to the top of the
head, but leave them out enough to slide the
housing over. This will prepare you for the
mounting instructions described in Assembly
on Page 19.
Figure 9. Board fastened to wall and ready for
G0440 motor/blower housing assembly.
Top Row Mounting Hole Height
Wall Stud Centers
Materials Needed for Concrete/
Masonry Wall
Concrete Anchor Stud
1
2" x 2
3
4" ............... 8*
Hex Nuts
1
2" .............................................. 8*
Flat Washers
1
2" ........................................ 8*
Hammer Drill .............................................. 1
Masonry Drill Bit
1
2" ................................... 1
Level 4' ....................................................... 1
Pencil .......................................................... 1
Measuring Tape .......................................... 1
*Two of these fastener sets will be used
in mounting the intake barrel brace during
assembly.
To mount the motor/impeller housing to a
concrete or masonry wall:
1. Copy the mounting hole layout pattern from
the motor housing to your wall, making sure
the Top Row Mounting Hole Height (see
Figures 78) is correct for your dust collec-
tor.
2. Mount the anchor studs to the wall in the
mounting hole locations for the motor/impel-
ler housing. This will prepare you for the
mounting instructions described in Assembly
on Page 19.
Model G0440/G0441 (Mfg. Since 03/12)
-19-
Assembly
To assemble dust collector:
1. With the help of assistants or power lifting
equipment, secure the motor/blower housing
assembly onto the hardware you mounted in
the Wall Mounting section.
2. Attach the 3 x 6mm foam tape to the top of
the intake cylinder, as shown in Figure 10.
Figure 10. Foam tape stuck on intake cylinder.
Intake
Cylinder
Foam Tape
3. Attach the intake cylinder to the bottom of the
housing, as shown in Figure 11, using (4)
5
16"-18 x
3
4" hex bolts and (4)
5
16" flat wash-
ers.
Note: Because this part of the dust collector
will not be accessible after assembly, con-
sider using medium strength thread locking
compound on the bolts that secure the intake
cylinder to the motor/blower housing assem-
bly. This added measure will ensure that the
fasteners will not come loose from vibration.
4. Temporarily attach the intake barrel to the
housing with a barrel gasket in between, as
shown in Figure 12, using (4)
5
16"-18 x
3
4"
hex bolts and (4)
5
16" flat washersand only
snug the bolts, rather than fully tighten them.
Figure 12. Securing blower on intake barrel.
Gasket Here
Intake Barrel
Figure 11. Attaching intake cylinder to the
bottom of motor housing.
Intake
Cylinder
Motor
Housing
HEAVY LIFT!
Straining or crushing injury
may occur from improperly
lifting machine or some of
its parts. To reduce this risk,
get help from other people
and use a fork lift (or other
lifting equipment) rated for
weight of this machine.
-20-
Model G0440/G0441 (Mfg. Since 03/12)
5. Place the intake barrel brace in position
and mark the location of the mounting holes
(shown in Figure 13) with a small pencil, nail,
or push pin.
Figure 14. Using tape on wrench in tight spot.
6. Remove the intake barrel you temporar-
ily attached in Step 4, drill holes where you
marked in Step 5, and loosely install the wall
mount brace to the wall with the remaining
fasteners from the Wall Mounting proce-
dure.
7. Use the (12)
5
16"-18 x
3
4" hex bolts and (12)
5
16" flat washers to re-install the intake bar-
rel to the housing with a barrel gasket in
between, as shown in Figure 12 on the previ-
ous page.
Note: When installing the two bolts above
the intake port, use duct tape on the bottom
of your wrench to hold the bolts in place, as
shown in Figure 14, to start the bolts easier.
Figure 13. Intake barrel brace positioned to
mark the mounting holes.
Mounting
Hole
Locations
8. Attach the cyclone funnel to the intake barrel
with a barrel gasket between them, as shown
in Figure 15, using (12)
5
16"-18 x 1" hex bolts,
(24)
5
16" flat washers, and (12)
5
16"-18 hex
nuts; also secure the wall mounting brace to
the lip of the intake barrel/funnel assembly
with the same hardware.
Note: At the places where you see 3 holes in
a row, only use the center hole for this step.
The two outside holes are only designed for
use with the optional stand.
Figure 15. Cyclone funnel attached to intake
barrel.
Barrel
Gasket Here
9. Tighten the wall mounting brace to the wall.
10. Attach the cyclone vacuum tube to the
cyclone funnel with (4)
5
16"-18 x
3
4" hex bolts
and (4)
5
16" flat washers (see Figure 16).
Figure 16. Cyclone vacuum tube and hose
attachment.
Model G0440/G0441 (Mfg. Since 03/12)
-21-
11. Attach the outlet port and filter L-braces to
the blower housing with the outlet gasket
between the outlet port and the housing, as
shown in Figures 1718, using (8)
5
16"-18 x
1" hex bolts, (16)
5
16" flat washers, and (8)
5
16"-18 hex nuts.
Note: On the G0441, one of the braces
attaches directly to the housing with the fol-
lowing extra hardware: (2)
5
16"-18 x 1" hex
bolts, (4)
5
16" flat washers, and (2)
5
16"-18 hex
nuts.
Figure 17. Model G0440 outlet port and filter
L-braces installed.
12. Mount the filter to the L-braces with the brace
gaskets between them, as shown in Figure
19, using (4)
5
16"-18 x
3
4" hex bolts and (4)
5
16" fender washers.
Figure 19. Mounting filters to the braces.
Brace Gasket Here
Figure 18. Model G0441 outlet port and filter
L-braces installed.
Outlet Gasket Here
13. Model G0440:
a. Apply the 3 x 15mm foam tape to
the edges of the outlet port and the
canister adapter, as shown in Figure 20.
Figure 20. Foam tape applied to the outlet port
and canister adapter (Model G0440).
Foam
Tape
-22-
Model G0440/G0441 (Mfg. Since 03/12)
b. Connect the gray flexible hose from
the outlet port to the canister adapter
and secure it in place with the two 7"
hose clamps, as shown in Figure 21.
Model G0441:
a. Apply the 3 x 15mm foam tape to
the lips of the outlet port, canister
adapter, and both ends of the muf-
fler, as shown in Figure 22.
Figure 22. Foam tape applied to upper
components (Model G0441).
Foam
Tape
Foam
Tape
b. Attach the 8" x 5" gray flexible hose
between the canister adapter and
the muffler with two 8" hose clamps,
then attach the 8" x 20" gray flexible
hose between the muffler and the
outlet port with the remaining two 8"
hose clamps (see Figure 23).
Note: It may be necessary to reposition the
canister L-braces down one bolt hole or
shorten the length of the longer piece of flex-
ible hose to accommodate the bend in the
hose.
Figure 23. Muffler properly positioned between
the two gray flexible hoses (Model G0441).
Muffler
14. Attach the casters to the bottom of the lower
collection drum, as shown in Figure 24, using
the (4)
3
8"-16 hex nuts, (8)
3
8" flat washers,
and (4)
3
8" lock washers included in the box
with the casters.
Figure 24. Casters attached to the lower
collection drum.
Figure 21. Gray hose properly installed (Model
G0440).
Hose
Clamps
Model G0440/G0441 (Mfg. Since 03/12)
-23-
NoteFor the Model G0441 Only: If you
plan to keep your machine under an 8' ceil-
ing, skip Step 15.
15. Model G0441: Connect the upper and lower
collection drums together and secure them
with the included metal clamp and provided
fasteners, as shown in Figure 25.
Figure 25. Installing metal clamp around
collection drum.
Fasteners
16. Install the drum latches, as shown in Figure
26, with the (6) #10-24 x
3
8" Phillips head
screws and (6) #10-24 hex nuts included in
the box with the drum latches. Make sure the
hex nuts are on the outside of the drum so
that they will not snag the plastic collection
bag.
NoteFor the Model G0441 Only: If you
are using the collection drum at full height,
use the extra (6) #10-24 Phillips head screws
and hex nuts provided to plug the lower latch
mounting holes.
Figure 26. Installing drum latches on collector
drum.
17. Place the collection drum vacuum ring on the
bottom of the collection drum (see Figure 27).
Note: During operation, this ring and the
vacuum connection to the cyclone funnel will
prevent the collection bag from collapsing.
Figure 27. Inserting collection drum vacuum
ring.
-24-
Model G0440/G0441 (Mfg. Since 03/12)
18. Insert the rubber seal over the top lip of the
collection drum rim. Pay special attention
to the direction of the seal, as shown in the
Figure 28.
Tip: To keep the seal in place, you can use
an adhesive applied to the rubber seal at
approximately 1" intervals.
Figure 28. Installing canister seal.
Seal
Drum
Rim
Optional
Adhesive
19. Insert the larger of the plastic collection bags
into the collection drum, place the lid on the
collection drum and hook the latch over the
lid, as shown in Figure 29, then clamp it in
place.
Figure 29. Latch hooked over lid for clamping.
20. Move the collector drum under the dust col-
lector and connect it to the cyclone funnel
with the clear flexible hose and the two 9"
hose clamps, as shown in Figure 30.
Figure 30. Drum attached to cyclone funnel with
clear 9" hose.
21. Connect the vacuum hose to the cyclone fun-
nel and collection drum vacuum tubes with
(2) 1
1
4" hose clamps (see Figure 31).
Figure 31. Connecting the vacuum hose.
Model G0440/G0441 (Mfg. Since 03/12)
-25-
22. Fit the plastic canister collection bag over
the bottom of the canister filter and clamp in
place with the metal bag clamp, as shown in
Figure 32.
Figure 32. Plastic collection bag clamped in
place under filter.
Bag
Clamp
23. Mount the switch on the funnel, as shown in
Figure 33, with the (2)
5
16"-18 x 1" hex bolts,
(4)
5
16" flat washers, and (2)
5
16"-18 hex nuts.
Test Run
Once the assembly is complete, test run your
machine to make sure it runs properly and is
ready for regular operation.
If, during the test run, you cannot easily locate
the source of an unusual noise or vibration, stop
using the machine immediately, then review the
Troubleshooting on Page 41.
If you still cannot remedy a problem, contact our
Tech Support at (570) 546-9663 for assistance.
To test run the machine:
1. Make sure you have read the safety instruc-
tions at the beginning of the manual and that
the machine is setup properly.
2. Make sure all tools and objects used during
setup are cleared away from the machine.
3. Press the ON/OFF button to turn the machine
ON.
4. Listen to and watch for abnormal noises or
actions. The machine should run smoothly
with little or no vibration or rubbing noises.
Strange or unusual noises should be inves-
tigated and corrected before operating the
machine further. Always disconnect the
machine from power when investigating or
correcting potential problems.
5. Press the TIMER button and cycle through
each of the times to make sure the lights illu-
minate on the switch.
6. Press the TIMER on the remote control and
cycle through each of the times in the same
manner as Step 5.
7. Press the ON/OFF button on the remote con-
trol to make sure it is working properly.
Figure 33. Switch mounted to funnel.
-26-
Model G0440/G0441 (Mfg. Since 03/12)
SECTION 4: DESIGNING THE
SYSTEM
General
Duct Material
You have many choices regarding main line and
branch line duct material. For best results, use
metal duct for the main line and branch lines, then
use short lengths of flexible hose to connect each
machine to the branch lines.
Plastic duct is also a popular material for home
shops. However, be aware that there is a fire or
explosion hazard if plastic duct material is used
for dust collection without being grounded against
static electrical charge build-up. This topic will be
discussed later in this section. Another problem
with using plastic is that it is less efficient per foot
than metal.
Plastic duct generates static
electrical buildup that can
cause fire or shock. Properly
ground it to reduce this risk.
Plastic Duct
Figure 34. Examples of plastic ducting
components.
The popularity of plastic duct is due to the fact
that it is an economical and readily available
product. It is also simple to assemble and easily
sealed against air loss. The primary disadvantage
of plastic duct for dust collection is the inherent
danger of static electrical build-up.
The Model G0440/G0441 works great as a central
system for a small shop or a dedicated dust col-
lector for large production machines.
When installing the dust collector be sure to put
it in an out of the way location such as a corner
or separate room. The dust collector is capable of
collecting dust from up to three machines running
simultaneously. Grizzly offers a complete line of
dust collection accessories for setting up a sta-
tionary system. Additionally, Grizzly offers a com-
plete guide book entitled Dust Collection Basics.
Whatever system you choose, always make sure
there are no open flames or pilot lights in the
same room as the dust collector. There is a risk of
explosion if dust is dispersed into the air.
Always guard against stat-
ic electrical build up by
grounding all dust collec-
tion lines.
Model G0440/G0441 (Mfg. Since 03/12)
-27-
There are a number of options when it comes to
metal duct, but metal duct that is specially manu-
factured for dust collection is the best choice.
When selecting your metal duct, choose high
quality metal duct with smooth welded internal
seams that will minimize airflow resistance. This
type of duct usually connects to other ducts
or elbows with a simple, self-sealing clamp, is
very quick and easy to assemble, and can be
readily dismantled and re-installed. This is espe-
cially important if you ever need to change things
around in your shop or add more tools.
Avoid inferior metal duct that requires you to cut it
to length and snap it together. This type of duct is
time consuming to install because it requires you
to seal all the seams with silicone and screw the
components on the ends with sheet metal screws.
Another disadvantage is the rough internal seams
and crimped ends that unavoidably increase static
pressure loss.
There are also many kinds of pure plastic flexible
hose, such as non-perforated drainage type hose
and dryer vent hose. Drainage type hose, while
being economical, does not quite have the flex-
ibility required for dust collection. The inside of the
duct is also deeply corrugated and can increase
the static pressure loss by as much as 50% over
smooth wall duct. Dryer vent hose, while being
completely flexible, is non-resistant to abrasion
and has a tendency to collapse in a negative
pressure system. We DO NOT recommend using
dryer vent hose in your dust collection system.
If using flex-hose, you should choose one of the
many types that are designed specifically for the
movement of solid particles, i.e. dust, grains,
and plastics. However, the cost of specifically
designed flexible duct can vary greatly. Grizzly
offers polyethylene hose, which is well suited for
the removal of particulate matter, especially saw-
dust, since it is durable and completely flexible.
Polyethylene is also very economical and avail-
able in a wide variety of diameters and lengths for
most applications.
Figure 36. Example of flexible metal duct.
Flexible Duct
Flexible hose is generally used for short runs,
small shops and at rigid duct-to-tool connections.
There are many different types of flex hose on
the market today. These are manufactured from
materials such as polyethylene, PVC, cloth hose
dipped in rubber and even metal, including steel
and aluminum.
The superior choice here is metal flex hose that is
designed to be flexible, yet be as smooth as pos-
sible to reduce static pressure loss.
Metal Duct
Advantages of metal duct is its conductivity and
that it does not contribute to static electrical
charge build-up. However, static charges are still
produced when dust particles strike other dust
particles as they move through the duct. Since
metal duct is a conductor, it can be grounded quite
easily to dissipate any static electrical charges.
Figure 35. Examples of metal pipe and
components.
-28-
Model G0440/G0441 (Mfg. Since 03/12)
System Design
Step 3. Sketch a Basic Duct Layout
Dust
Collector
Figure 37. Basic sketch of shop layout.
Figure 38. Efficient duct layout.
Main
Line Duct
Branch
Line
Ducts
GOOD
Dust
Collector
Figure 39. Inefficient duct layout.
BAD
Dust
Collector
For the next step, sketch how you will connect
your machines to the dust collector. Consider
these general guidelines for an efficient system:
1. Machines that produce the most saw dust
should be placed nearest to the dust collector
(i.e. planers and sanders).
2. Ideally, you should design the duct system to
have the shortest possible main line and sec-
ondary branch ducts. See the figures below
for ideas of efficient versus inefficient duct
layouts.
Step 1. Decide Who Will Design
For most small-to-medium sized shops, you can
design and build the dust collection system your-
self without hiring engineers or consultants. We
have included some basic information here to get
you started on a basic design.
If you have a large shop or plan to design a com-
plicated system, we recommend doing additional
research beyond this manual or seeking the help
of an expert.
Step 2. Sketch Your Shop Layout
When designing a successful dust collection sys-
tem, planning is the most important step. In this
step, sketch a basic layout of your shop, including
space requirements of different machines.
Before you get out your pencil and paper, we rec-
ommend you visit our FREE Workshop Planner
available on our website at www.grizzly.com.
Our Workshop Planner will allow you to quickly
and easily design and print a basic shop layout.
Don't worry, non-Grizzly brand machines can be
substituted with Grizzly machines for layout pur-
poses. Note: After you're finished, make sure to
save your layout for later modification.
Your sketch only needs the basic details of the
shop layout, similar to the Figure below, includ-
ing all your current/planned machines and your
planned placement of the dust collector.
Model G0440/G0441 (Mfg. Since 03/12)
-29-
3. Directional changes should be kept to a mini-
mum. The more directional change fittings
you use directly increases the overall resis-
tance to airflow.
4. Gradual directional changes are more effi-
cient than sudden directional changes (i.e.
use the largest corner radius possible when
changing hose or pipe direction).
5. Each individual branch line should have a
blast gate immediately after the branch to
control suction from one machine to another.
6. The simpler the system, the more efficient
and less costly it will be.
Step 4. Determine Required CFMs
Since each machine produces a different amount
of sawdust, the requirements for the minimum
amount of CFM to move that sawdust is unique
to the machine (for example, a planer produces
more sawdust than a table saw). Knowing this
required CFM is important to gauging which size
of duct to use.
Refer to the Figure below for a close estimation of
the airflow each machine requires. Keep in mind
that machines that generate the most sawdust
should be placed closest to the dust collector.
If the machine has multiple dust ports, the total
CFM required is the sum of all ports.
Figure 40. Approximate required airflow for
machines, based on dust port size.
Machine
Dust Port Size
Approximate
Required CFM
2" 98
2.5" 150
3" 220
4" 395
5" 614
6" 884
7" 1203
8" 1570
9" 1990
10" 2456
If the machine does not have a built-in dust port,
use the following table to determine which size of
dust port to install.
Figure 41. Dust port size and quantity per
average machine.
Machine Average Dust Port Size
Table Saw ...................................................... 4"
Miter/Radial-Arm Saw ....................................2"
Jointer (6" and smaller) ................................. 4"
Jointer (8"-12") ............................................... 5"
Thickness Planer (13" and smaller) ............... 4"
Thickness Planer (14"-20") ............................6"
Shaper ........................................................... 4"
Router (mounted to table) ..............................2"
Bandsaw ........................................................ 4"
Lathe .............................................................. 4"
Disc Sander (12" and smaller) .......................2"
Disc Sander (13-18") ...................................... 4"
Belt Sander (6" and smaller) .........................2"
Belt Sander (7"-9") ........................................3"
Edge Sander (6" x 80" and smaller) .............. 4"
Edge Sander (6" x 80" and larger) ................ 5"
Drum Sander (24" and smaller) ............... 2 x 4"
Drum Sander (24" and larger) ................. 4 x 4"
Widebelt Sander (18" and smaller) ................ 5"
Widebelt Sander (24"-37" single head) ...2 x 6"
Widebelt Sander (24"-51" double head) .. 5 x 4"
Figure 42. CFM requirements labeled for each
machine.
395
395
614
790 395
220
98
Table Saw
Planer/
Moulder
Miter
Saw
Jointer Sander
Planer Shaper
Dust
Collector
Write the required CFM for each machine on your
sketch, as shown in the figure below.
-30-
Model G0440/G0441 (Mfg. Since 03/12)
The general rule of thumb for a main line duct is
that the velocity of the airflow must not fall below
3500 FPM.
For small/medium sized shops, using the inlet size
of the dust collector as the main line duct size
will usually keep the air velocity above 3500 FPM
and, depending on your system, will allow you to
keep multiple branches open at one time.
Mark your drawing, as shown in the figure below,
but using the inlet size for your dust collector as
the main line.
The general rule of thumb for a branch line duct is
that the velocity of the airflow must not fall below
4000 FPM.
For small/medium sized shops, using the dust
port size from the machine as the branch line duct
size will achieve the correct velocity in most appli-
cations. However, if the dust port on the machine
is smaller than 4", make the branch line 4" and
neck the line down right before the dust port.
Note: Systems with powerful dust collectors work
better if multiple blast gates are left open. This
also allows you to run two machines at once.
Experiment with different combinations of blast
gates open/closed to find the best results for your
system.
Write your determined branch line sizes on your
drawing, as shown in the following Figure.
Figure 43. Main line size labeled on sketch.
395
395
614
790 395
220
98
Dust
Collector
5" 6" 7"
Table Saw
Planer/
Moulder
Miter
Saw
Jointer Sander
Planer Shaper
The general rule of thumb for a branch line duct is
that the velocity of the airflow must not fall below
4000 FPM.
For small/medium sized shops, using the dust
port size from the machine as the branch line duct
size will achieve the correct velocity in most appli-
cations. However, if the dust port on the machine
is smaller than 4", make the branch line 4" and
neck the line down right before the dust port.
Note: Systems with powerful dust collectors work
better if multiple blast gates are left open. This
also allows you to run two machines at once.
Experiment with different combinations of blast
gates open/closed to find the best results for your
system.
Write your determined branch line sizes on your
drawing, as shown in the following Figure.
Determining Branch Line Duct Size
Figure 44. Branch line duct sizes labeled.
395
395
614
790 395
220
98
4"
4"
4" 6"
4" 4" 5"
5" 6" 7"
Table Saw
Miter
Saw
Jointer Sander
Planer Shaper
Planer/
Moulder
Dust
Collector
Plan the drop downs for each machine, using
blast gates wherever possible to control airflow.
Planning Drop Downs
To Planer
Blast Gate
Flex Pipe
Rigid Pipe
Rigid Pipe
(Main Line)
Elbow
Clamp
Y Branch
Figure 45. Drop down setup.
Determining Main Line Duct Size
Model G0440/G0441 (Mfg. Since 03/12)
-31-
Figure 46. Static pressure loss tables.
Duct
Dia.
Approximate
Static Pressure
Loss Per Foot of
Rigid Pipe
Approximate
Static Pressure
Loss Per Foot
of Flex Pipe
Main
Lines
at 3500
FPM
Branch
Lines
at 4000
FPM
Main
Lines
at 3500
FPM
Branch
Lines
at 4000
FPM
2" 0.091 0.122 0.35 0.453
2.5" 0.08 0.107 0.306 0.397
3" 0.071 0.094 0.271 0.352
4" 0.057 0.075 0.215 0.28
5" 0.046 0.059 0.172 0.225
6" 0.037 0.047 0.136 0.18
7" 0.029 0.036 0.106 0.141
8" 0.023 0.027 0.08 0.108
9" 0.017 0.019 0.057 0.079
Fitting
Dia.
90
Elbow
45
Elbow
45
Wye(Y)
90
Wye(Y)
3" 0.47 0.235 0.282 0.188
4" 0.45 0.225 0.375 0.225
5" 0.531 0.266 0.354 0.236
6" 0.564 0.282 0.329 0.235
7" 0.468 0.234 0.324 0.216
8" 0.405 0.203 0.297 0.189
In most small/medium shops it is only necessary
to calculate the line with the longest duct length or
the most fittings (operating under the assumption
that if the line with the highest resistance works,
the others will be fine).
To calculate the static pressure of any given
line in the system, follow these steps:
1. Make a list of each size duct in the line,
including the length, and multiply those num-
bers by the static pressure value given in the
previous table.
2. List each type of elbow or branch and multiply
the quantity (if more than one) by the static
pressure loss given in the previous table.
Two Machines on Same Branch Line
Total CFM Branch Line Size
400 4"
500 4"
600 5"
700 5"
800 6"
900 6"
1000 6"
Adding duct work, elbows, branches and any
other components to a duct line increases airflow
resistance (static pressure loss). This resistance
can be minimized by using rigid (smooth) pipe and
gradual curves, as opposed to flexible pipe and
90 elbows.
To help you think about this resistance, imagine
riding a bicycle in a tunnel that is an exact replica
of your duct work. If the inside of the tunnel is very
bumpy (flexible pipe) and has a lot of sharp turns
(90 elbows), it will take a lot more effort to travel
from one end to the other.
The purpose of calculating the resistance is to
determine if it is low enough from the machine to
the dust collector to meet the given CFM require-
ment for the machine. Use the following tables to
calculate the resistance of duct work.
Calculating Duct Resistance
Multiple Dust Ports
If your machine has multiple dust ports, add the
total CFM given for each dust port size from
the table provided in the earlier subsection,
Determine Required CFMs, then find the closest
CFM in the table below to determine the correct
branch size. Split the branch line just before the
dust ports with matching duct sizes.
If two machines will connect to the same branch
line and both will operate at the same time, then
add the required CFM for each machine together
and find the closest total CFM in the table below
to determine the correct branch size.
If both machines will never run at the same time,
reference the machine with the biggest dust port
in the table below and add blast gates after the
Y-branch to open/close the line to each machine.
-32-
Model G0440/G0441 (Mfg. Since 03/12)
Figure 47. Additional factors affecting static
pressure.
Additional Factors Static Pressure
Seasoned (well used)
Dust Collection Filter
1"
Entry Loss at Large
Machine Hood
2"
Figure 48. Totaling static pressure numbers.
Main Line
6" Rigid Pipe (0.037) at 20' ................ 0.740
Branch Line
4" Rigid Pipe (0.075) at 10' ................ 0.750
4" Flex Pipe (0.28) at 5' ........................ 1.400
Elbows/Branches
6" 45 Y-Branch ................................ 0.329
4" 45 Elbow ........................................ 0.225
Additional Factors
Seasoned Filter ................................ 1.000
Total Static Pressure Loss ................ 4.444
4. Total your list as shown in the example below
to come up with your overall static pressure
loss number for that line.
Note: Always account for a seasoned filter,
so you don't end up with a system that only
works right when the filter is clean.
Note: When calculating static pressure loss
to determine if multiple lines can be left open
at the same time, only include the main line
numbers once.
3. Add the additional factors from the following-
table to your list.
5. Compare the total static pressure loss for that
line to the closest CFM given in Figure 50 for
your dust collector on Page 34.
Example: A typical Data Sheet Performance
Curve is illustrated in Figure 49. Find 4.4 on
the Static Pressure axis (the amount of total
static pressure loss calculated in Figure 48),
then refer to the closest value on the CFM
axisapproximately 1120 CFM.
The 1120 CFM for the static pressure loss of
the line connected to the router is well above
the 220 CFM requirement of that machine.
-6-
G0440/G0441/G0443 Cyclone Dust Collectors
93
3
8"
67"
75
1
4"
26
7
8"
32
7
8"
24
1
2"
15
3
4"
43
3
4"
7"
37
3
4"
59
1
16"
32
7
8"
7"
32
7
8"
7"
17
1
4"
G0440 MACHINE
DATA SHEET
Customer Service #: (570) 546-9663 To Order Call: (800) 523-4777 Fax #: (800) 438-5901
MODEL G0440
2 HP TWO-STAGE CYCLONE DUST COLLECTOR
2005 BY GRIZZLY INDUSTRIAL
F
2
5
0
V
A
C
220V Motor
220V
Circuit Board
220V Magnetic Contactor
Switch and Overload Relay
Ground
Hot
Hot
DISCONNECT
SWITCH
(as recommended)
1-PHASE
220 VAC
G0440 Wiring Diagram
-44-
Model G0440/G0441 (Mfg. Since 03/12)
READ ELECTRICAL SAFETY
ON PAGE 42!
A1
G
r
o
u
n
d
2T1 6T3 14NO 4T2
1L1 5L3 13NO 3L2
NHD C-18D
2T1 4T2 6T3
98 97
A2
96
O R
95
2
1
23
2
4
2
5
NHD NTH-25
ON/OFF
Switch
A2
OL_NO AC
OUT
AC
IN
S
t
a
r
t
C
a
p
a
c
i
t
o
r
6
0
0
M
F
D
1
2
5
V
A
C
R
u
n
C
a
p
a
c
i
t
o
r
6
0
F
3
0
0
V
A
C
220V Motor
220V
Circuit Board
220V Magnetic Contactor
Switch and Overload Relay
Ground
Hot
Hot
DISCONNECT
SWITCH
(as recommended)
1-PHASE
220 VAC
G0441 Wiring Diagram
Model G0440/G0441 (Mfg. Since 03/12)
-45-
READ ELECTRICAL SAFETY
ON PAGE 42!
G0440/G0441 Electrical Components
Figure 69. G0441 magnetic switch assembly.
Contactor
Overload
Relay
Circuit Board
Magnetic Switch
Junction Box
220V
1
2
CONNECTION
Motor Wiring
Figure 67. Motor wiring. Figure 68. Motor wiring schematic.
-46-
Model G0440/G0441 (Mfg. Since 03/12)
1 1-1
1-2
1-3
1-4 1-5
1-6
2
3V3
4
5
6
7
8
9
10
11
12
13
14A
15
16
17
18V2
19
20
21
22
23
24
25
26
27
28
28-1
29
30 31
32V3
32V3-1
32V2-2
32V2-3
32V2-4
32V2-5
34V2
35
36
37
38
39
40
41
42
43
44V2
45
46
47
48
49
50
51V2
52V2A
52V2
53
54
55
56
57
58
59
60
94
95
61
62V2
63
64
65
66
67
68
69
70
71
72V2
73
74
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
79
26
46
61
96
32V2-3
59
48
DUTY
Grizzly Cyclone Induction Motor
Connections:
Manufactured for Grizzly in Taiwan
HEAT WEIGHT CLASS
DATE
HZ
SER. NO.
VOLT
OUTPUT
AMP
RPM PHASE
3V3-1
3V3-2
3V3-3
3V3-4
1-9
1-7
1-10
1-8
SECTION 10: PARTS
g
G0440 Main
Model G0440/G0441 (Mfg. Since 03/12)
-47-
G0440 Parts List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 P0440001 MOTOR 2HP 220V 1-PH 39 P0440039 BARREL GASKET 584MM DIA.
1-1 P0440001-1 MOTOR FAN COVER 40 P0440040 INTAKE BARREL 20"
1-2 P0440001-2 MOTOR FAN 41 P0440041 HEX BOLT 5/16-18 X 3/4
1-3 P0440001-3 CAPACITOR COVER 42 P0440042 FLAT WASHER 5/16
1-4 P0440001-4 S CAPACITOR 300M 125V 1-3/4 X 3-3/8 43 P0440043 BARREL GASKET 584MM DIA.
1-5 P0440001-5 R CAPACITOR 50M 250V 1-5/8 X 3-1/2 44V2 P0440044V2 CYCLONE FUNNEL 20" V2.08.10
1-6 P0440001-6 JUNCTION BOX 45 P0440045 HEX BOLT 5/16-18 X 1
1-7 P0440001-7 BALL BEARING 6205ZZ 46 P0440046 FLAT WASHER 5/16
1-8 P0440001-8 BALL BEARING 6203ZZ 47 P0440047 HEX NUT 5/16-18
1-9 P0440001-9 CONTACT PLATE 48 P0440048 HOSE CLAMP 9"
1-10 P0440001-10 CENTRIFUGAL SWITCH 3450 49 P0440049 CLEAR FLEX PIPE 9" x 200MM
2 P0440002 MOTOR CORD 12G 3C 50 P0440050 COLLECTION DRUM LID V2.08.06
3V3 P0440003V3 REMOTE MAG SWITCH 220V V3.01.12 51V2 P0440051V2 DRUM SEAL TYPE-T 2.1M V2.11.09
3V3-1 P0440003V3-1 CONTACTOR NHD C-12D 220V 52V2A P0440052V2A COLLECTION DRUM ASSY 35GAL V2.08.10
3V3-2 P0440003V3-2 OL RELAY NHD NTH-14 11-14A 52V2 P0440052V2 COLLECTION DRUM 35GAL V2.08.10
3V3-3 P0440003V3-3 CIRCUIT BOARD 220V W/TRANSFORMER 53 P0440053 DRUM LID LATCH ASSEMBLY
3V3-4 P0440003V3-4 ON/OFF SWITCH 110V/220V 54 P0440054 PHLP HD SCR 10-24 X 3/8
4 P0440004 REMOTE CONTROLLER 55 P0440055 HEX NUT 10-24
5 P0440005 HEX BOLT 3/8-16 X 1-1/2 56 P0440056 CASTER 2"
6 P0440006 FLAT WASHER 3/8 57 P0440057 HEX NUT 3/8-16
7 P0440007 LOCK WASHER 3/8 58 P0440058 LOCK WASHER 3/8
8 P0440008 HEX NUT 3/8-16 59 P0440059 FLAT WASHER 3/8
9 P0440009 BLOWER COVER 60 P0440060 HEX BOLT 5/16-18 X 1
10 P0440010 HEX BOLT 3/8-16 X 1 61 P0440061 FLAT WASHER 5/16
11 P0440011 FENDER WASHER 3/8 62V2 P0440062V2 SWITCH MOUNTING BRACKET V2.01.12
12 P0440012 LOCK WASHER 3/8 63 P0440063 HEX NUT 5/16-18
13 P0440013 HEX NUT 3/8-16 64 P0440064 WALL MOUNTING BRACE
14A P0440014A IMPELLER 14-1/2" V2.02.06 65 P0440065 MOTOR SPEC LABEL
15 P0440015 IMPELLER FENDER WASHER 3/8 66 P0440066 MOTOR WARNING LABEL
16 P0440016 HEX BOLT 3/8-16 X 1 LH 67 P0440067 GLASSES/RESPIRATOR LABEL
17 P0440017 FOAM TAPE 3 X 6 X 1600MM 68 P0440068 READ MANUAL LABEL
18V2 P0440018V2 BLOWER HOUSING 14.5" IMP V2.02.06 69 P0440069 HANDS/INLET LABEL
19 P0440019 FLAT WASHER 5/16 70 P0440070 RETURN RED HANDLE LABEL
20 P0440020 HEX BOLT 5/16-18 X 3/4 71 P0440071 ELECTRICITY LABEL
21 P0440021 OUTLET GASKET 306 X 226MM 72V2 P0440072V2 MACHINE ID LABEL CSA V2.01.12
22 P0440022 OUTLET PORT 73 P0440073 MODEL NO/HP/GRIZZLY LABEL (LARGE)
23 P0440023 HEX BOLT 5/16-18 X 1 74 P0440074 MODEL NO/HP/GRIZZLY LABEL (SMALL)
24 P0440024 FLAT WASHER 5/16 77 P0440077 EXT TOOTH WASHER 3/8
25 P0440025 HEX NUT 5/16-18 78 P0440078 MOTOR MOUNT GASKET
26 P0440026 HOSE CLAMP 7" 79 P0440079 FOAM TAPE 3 X 15 X 600MM
27 P0440027 GRAY FLEX PIPE 7" X 800MM 80 P0440080 CYCLONE VACUUM TUBE
28 P0440028 FILTER L-BRACE (LH) 81 P0440081 FLAT WASHER 5/16
28-1 P0440028-1 BRACE GASKET 155 X 37MM 82 P0440082 HEX BOLT 5/16-18 X 3/4
29 P0440029 FILTER L-BRACE (RH) 83 P0440083 TUBE PLUG 1-1/4"
30 P0440030 HEX BOLT 5/16-18 X 3/4 84 P0440084 FOAM TAPE 3 X 6 X 300MM
31 P0440031 FLAT WASHER 5/16 85 P0440085 VACUUM HOSE 1-1/4" X 98"
32V3 P0440032V3 CANISTER ASSEMBLY (BEIGE) V3.07.12 86 P0440086 COLLECTION DRUM VACUUM TUBE
32V3-1 P0440032V3-1 CANISTER CAGE ASSY (BEIGE) V3.07.12 87 P0440087 FLAT WASHER 5/16
32V2-2 P0440032V2-2 FOAM TAPE 3 X 25 X 1400MM V2.11.09 88 P0440088 HEX BOLT 5/16-18 X 3/4
32V2-3 P0440032V2-3 FOAM TAPE 3 X 35 X 1255MM V2.11.09 89 P0440089 HOSE CLAMP 1-1/4"
32V2-4 P0440032V2-4 CAN FILTER 386MM W/FOAM TAPE V2.11.09 90 P0440090 TUBE PLUG 1-1/4"
32V2-5 P0440032V2-5 BAG CLAMP 445MM V2.11.09 91 P0440091 FOAM TAPE 3 X 6 X 300MM
34V2 P0440034V2 PLASTIC BAG 470 X 600MM V2.11.09 92 P0440092 COLLECTION DRUM VACUUM RING
35 P0440035 FOAM TAPE 3 X 6 X 1600MM 93 P0440093 DRUM COLLECTION BAG 640 X 1000MM
36 P0440036 INTAKE CYLINDER 10" 94 P0440094 JUNCTION BOX
37 P0440037 FLAT WASHER 5/16 95 P0440095 JUNCTION BOX CORD 12G 3C 12"
38 P0440038 HEX BOLT 5/16-18 X 3/4 96 P0440096 GROUNDING WIRE 12G 6" (GREEN)
-48-
Model G0440/G0441 (Mfg. Since 03/12)
G0441 Main
71
72
73
74
75
76
77
78V2
DUTY
Grizzly Cyclone Induction Motor
Connections:
Manufactured for Grizzly in Taiwan
HEAT
WEIGHT
CLASS
DATE
HZ
SER. NO.
VOLT
OUTPUT
AMP
RPM
PHASE
79
80
1
2
3V3
4
5
6
7
8
9
10
11
12
13
14A
15
16
17
18A
19
20
21
22
23
24
25
26
27A-1
27A-2
28
28-1
29
30
31
32V3
32V3-1
32V2-2
32V2-3
32V2-4
32V2-5
34V2
35
36
37
38
39
40
41
42
43
44V2
45
46
47
48
49
50
51V3
52
53V2
54
55
56
57
58
59
60
61
62
63
64
65
67
68V2
69
70
83
84
85
86
100
101
102
103
104
105
106
107 108
109
110
111
112
113
114
26
26
85
26
46
46
85
32V2-3
48
53V2A
66
94
95
96
3V3-1
3V3-2
3V3-3
3V3-4
1-1
1-2
1-3
1-4 1-5
1-6
1-9
1-7
1-10
1-8
Model G0440/G0441 (Mfg. Since 03/12)
-49-
G0441 Parts List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 P0441001 MOTOR 3HP 220V 1-PH 43 P0441043 BARREL GASKET 584MM DIA.
1-1 P0441001-1 MOTOR FAN COVER 44V2 P0441044V2 CYCLONE FUNNEL 20" V2.08.10
1-2 P0441001-2 MOTOR FAN 45 P0441045 HEX BOLT 5/16-18 X 1
1-3 P0441001-3 CAPACITOR COVER 46 P0441046 FLAT WASHER 5/16
1-4 P0441001-4 S CAPACITOR 600M 125V 1-3/4 X 3-3/4 47 P0441047 HEX NUT 5/16-18
1-5 P0441001-5 R CAPACITOR 60M 300V 1-5/8 X 3-1/2 48 P0441048 HOSE CLAMP 9"
1-6 P0441001-6 JUNCTION BOX 49 P0441049 CLEAR FLEX PIPE 9" X 340MM
1-7 P0441001-7 BALL BEARING 6205ZZ 50 P0441050 COLLECTION DRUM LID V2.08.06
1-8 P0441001-8 BALL BEARING 6203ZZ 51V3 P0441051V3 DRUM SEAL TYPE-R 2M V3.01.12
1-9 P0441001-9 CONTACT PLATE 52 P0441052 UPPER DRUM 25GAL
1-10 P0441001-10 CENTRIFUGAL SWITCH 3450 53V2A P0441053V2A COLLECTION DRUM ASSY 55GAL V2.11.09
2 P0441002 MOTOR CORD 12G 3C 53V2 P0441053V2 COLLECTION DRUM 35GAL V2.08.10
3V3 P0441003V3 REMOTE MAG SWITCH 220V V3.01.12 54 P0441054 DRUM CLAMP
3V3-1 P0440003V3-1 CONTACTOR NHD C-18D 220V 55 P0441055 HEX BOLT 5/16-18 X 3
3V3-2 P0440003V3-2 OL RELAY NHD NTH-25 2125A 56 P0441056 HEX NUT 5/16-18
3V3-3 P0440003V3-3 CIRCUIT BOARD 220V W/TRANSFORMER 57 P0441057 DRUM LID LATCH ASSEMBLY
3V3-4 P0440003V3-4 ON/OFF SWITCH 110/220V 58 P0441058 PHLP HD SCR 10-24 X 3/8
4 P0441004 REMOTE CONTROLLER 59 P0441059 HEX NUT 10-24
5 P0441005 HEX BOLT 3/8-16 X 1-1/2 60 P0441060 PHLP HD SCR 10-24 X 3/8
6 P0441006 FLAT WASHER 3/8 61 P0441061 HEX NUT 10-24
7 P0441007 LOCK WASHER 3/8 62 P0441062 CASTER 2"
8 P0441008 HEX NUT 3/8-16 63 P0441063 HEX NUT 3/8-16
9 P0441009 BLOWER COVER 64 P0441064 LOCK WASHER 3/8
10 P0441010 HEX BOLT 3/8-16 X 1-1/2 65 P0441065 FLAT WASHER 3/8
11 P0441011 FLAT WASHER 3/8 66 P0441066 HEX BOLT 5/16-18 X 1
12 P0441012 LOCK WASHER 3/8 67 P0441067 FLAT WASHER 5/16
13 P0441013 HEX NUT 3/8-16 68V2 P0441068V2 SWITCH MOUNTING BRACKET V2.01.12
14A P0441014A IMPELLER 15-1/2" V2.02.06 69 P0441069 HEX NUT 5/16-18
15 P0441015 IMPELLER FENDER WASHER 3/8 70 P0441070 WALL MOUNT BRACKET
16 P0441016 HEX BOLT 3/8-16 X 1 LH 71 P0441071 MOTOR SPEC LABEL
17 P0441017 FOAM TAPE 3 X 6 X 1600MM 72 P0441072 MOTOR WARNING LABEL
18A P0441018A BLOWER HOUSING 15-1/2" IMP V2.02.06 73 P0441073 GLASSES/RESPIRATOR LABEL
19 P0441019 FLAT WASHER 5/16 74 P0441074 READ MANUAL LABEL
20 P0441020 HEX BOLT 5/16-18 X 3/4 75 P0441075 HANDS/INLET LABEL
21 P0441021 OUTLET GASKET 326 X 226MM 76 P0441076 RETURN RED HANDLE LABEL
22 P0441022 OUTLET PORT 77 P0441077 ELECTRICITY LABEL
23 P0441023 HEX BOLT 5/16-18 X 1 78V2 P0441078V2 MACHINE ID LABEL CSA V2.01.12
24 P0441024 FLAT WASHER 5/16 79 P0441079 MODEL NO/HP/GRIZZLY LABEL (LARGE)
25 P0441025 HEX NUT 5/16-18 80 P0441080 MODEL NO/HP/GRIZZLY LABEL (SMALL)
26 P0441026 HOSE CLAMP 8" 83 P0441083 MUFFLER 8"
27A-1 P0441027A-1 GREY FLEX PIPE 8" X 500MM V2.04.08 84 P0441084 EXT TOOTH WASHER 3/8
27A-2 P0441027A-2 GREY FLEX PIPE 8" X 120MM V2.04.08 85 P0441085 FOAM TAPE 3 X 15 X 700MM
28 P0441028 FILTER L-BRACE (RH) 86 P0441086 MOTOR MOUNT GASKET
28-1 P0441028-1 BRACE GASKET 240 X 32MM 94 P0441094 JUNCTION BOX
29 P0441029 FILTER L-BRACE (LH) 95 P0441095 JUNCTION BOX CORD 12G 3C 12"
30 P0441030 HEX BOLT 5/16-18 X 3/4 96 P0441096 GROUNDING WIRE 12G 6" (GREEN)
31 P0441031 FLAT WASHER 5/16 100 P0441100 COLLECTION DRUM EXT KIT
32V3 P0441032V3 CANISTER ASSEMBLY (BEIGE) V3.07.12 101 P0441101 CYCLONE VACUUM TUBE
32V3-1 P0441032V3-1 CANISTER CAGE ASSY (BEIGE) V3.07.12 102 P0441102 FLAT WASHER 5/16
32V2-2 P0441032V2-2 FOAM TAPE 3 X 25 X 1400MM V2.11.09 103 P0441103 HEX BOLT 5/16-18 X 3/4
32V2-3 P0441032V2-3 FOAM TAPE 38 X 35 X 1460MM V2.11.09 104 P0441104 TUBE PLUG 1-1/4"
32V2-4 P0441032V2-4 CANISTER FILTER 486MM V2.11.09 105 P0441105 FOAM TAPE 3 X 6 X 300MM
32V2-5 P0441032V2-5 BAG CLAMP 545MM V2.11.09 106 P0441106 VACUUM HOSE 1-1/4" X 98"
34V2 P0441034V2 PLASTIC BAG 570 X 600MM V2.11.09 107 P0441107 COLLECTION DRUM VACUUM TUBE
35 P0441035 FOAM TAPE 3 X 6 X 1600MM 108 P0441108 FLAT WASHER 5/16
36 P0441036 INTAKE CYCLINDER 10" 109 P0441109 HEX BOLT 5/16-18 X 3/4
37 P0441037 HEX BOLT 5/16-18 X 3/4 110 P0441110 HOSE CLAMP 1-1/4"
38 P0441038 FLAT WASHER 5/16 111 P0441111 TUBE PLUG 1-1/4"
39 P0441039 BARREL GASKET 584MM DIA. 112 P0441112 FOAM TAPE 3 X 6 X 300MM
40 P0441040 INTAKE BARREL 20" 113 P0441113 COLLECTION DRUM VACUUM RING
41 P0441041 HEX BOLT 5/16-18 X 3/4 114 P0441114 DRUM COLLECTION BAG 640 X 1200MM
42 P0441042 FLAT WASHER 5/16
-50-
Model G0440/G0441 (Mfg. Since 03/12)
C
U
T
A
L
O
N
G
D
O
T
T
E
D
L
I
N
E
Name _____________________________________________________________________________
Street _____________________________________________________________________________
City _______________________ State _________________________ Zip _____________________
Phone # ____________________ Email _________________________________________________
Model # ____________________ Order # _______________________ Serial # __________________
WARRANTY CARD
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement ____ Friend ____ Catalog
____ Card Deck ____ Website ____ Other:
2. Which of the following magazines do you subscribe to?
3. What is your annual household income?
____ $20,000-$29,000 ____ $30,000-$39,000 ____ $40,000-$49,000
____ $50,000-$59,000 ____ $60,000-$69,000 ____ $70,000+
4. What is your age group?
____ 20-29 ____ 30-39 ____ 40-49
____ 50-59 ____ 60-69 ____ 70+
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years ____ 8-20 Years ____20+ Years
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5 ____ 6-9 ____10+
7. Do you think your machine represents a good value? _____Yes _____No
8. Would you recommend Grizzly Industrial to a friend? _____Yes _____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____Yes _____No
10. Comments: _____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
____ Cabinetmaker & FDM
____ Family Handyman
____ Hand Loader
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Old House Journal
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rife
____ Shop Notes
____ Shotgun News
____ Todays Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Woodwork
____ Woodworker West
____ Woodworkers Journal
____ Other:
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
FOLD ALONG DOTTED LINE
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
Place
Stamp
Here
Name_______________________________
Street_______________________________
City______________State______Zip______
Send a Grizzly Catalog to a friend:
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzlys sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzlys liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a Return Number, which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
WARRANTY AND RETURNS