PA1500L-M0 rev 08/07

Air Hydraulic Pumps

Instruction Manual
MODELS: PA1500L & PA3801L
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419 * Fax: 816-891-6599
E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com

! This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.

Maximum Operating Pressure 10,000 PSI

Printed in Taiwan
Save these instructions. For your safety, read and PRODUCT DESCRIPTION
understand the information contained within. The owner and BVA Hydraulics Air Hydraulic Pumps are engineered to meet
operator shall have an understanding of this product and safe most Industrial Standards for Performance and Safety. Its
operating procedures before attempting to use this product. unique hydraulic circuit allows quick displacement of hydraulic
Instructions and safety information shall be conveyed in fluid under no load conditions and easy pumping in loaded
the operator's native language before use of this product conditions. These air actuated pumps supply compressed
is authorized. Make certain that the operator thoroughly hydraulic fluid to compatible applications i.e. rams, presses,
understands the inherent dangers associated with the use and spreaders, compactors and crimping machines, anywhere
misuse of the product. If any doubt exists as to the safe and that 10,000 PSI of fluid pressure is needed. Special skill,
proper use of this product as outlined in this factory authorized knowledge and training may be required for a specific task
manual, remove from service immediately. and the product may not be suitable for all the jobs described
Inspect before each use. It is recommended that, prior to above. Unsuitable applications would include applications
each use, an inspection be done by qualified personnel and that call for a device to move, level or support persons,
that any missing or damaged parts, decals, warning/ safety animals, hazardous materials, mobile homes/ dwellings in
labels or signs be replaced with BVA Hydraulics authorized general, mirrors and/or plate glass, and/or to connect/secure
replacement parts only. Any pump that appears to be damaged hatches, components, etc. between bulkheads. The user
in any way, is worn, leaking or operates abnormally shall be must ultimately make the decision regarding suitability of the
removed from service immediately until such time as repairs product for any given task and assume the responsibility of
can be made. Any pump that has been or suspected to have safety for himself or herself and others in the work area.
been subject to a shock load (a load dropped suddenly,
causing the system pressure to exceed 10,000 PSI), shall ! WARNING: To reduce the risk of personal injury and/or
be removed from service immediately until checked out by property damage, ensure that the rated working pressure of
a BVA Hydraulics authorized service center. Owners and each pressurized attachment be equal to or greater than the
operators of this equipment shall be aware that the use and rated working pressure developed by the hydraulic pump.
subsequent repair of this equipment may require special
training and knowledge.
! Always check connections before using. Alteration
of these products is strictly prohibited. Use only those
adapters and attachments provided and approved by the
manufacturer.

SPECIFICATIONS
Model Usable Oil Rated Output Flow Rate Inpur Air Output Input Weight
Number Capacity Pressure (in3/min) Pressure Port Port (lbs)
(in3) (psi) No Load Load (psi) Threads Threads

PA1500L 91.5 19.4

10,000 61 10 110-175 3/8"-18NPT 1/4"-18NPT
PA3801L 231.9 30.4

Handle

Plastic Plug Manifold Plug/

Oil Output Port

Color Coded Hose

Advance Button

Remote Control
Oil Reservoir
Hex Plug/
Second Air Input Port
Retract Button First Air
Input Port

Figure 1 - Model PA1500L & PA3801L Components (PA1500L shown)

2
 BEFORE USE ASSEMBLY
1. Before using this product, read the instruction manual To hook up pump with remote control:
completely and familiarize yourself thoroughly with the 1. Connect red hose into air line coupler number 1 on the pump
product and the hazards associated with its improper and then put other end of red hose into corresponding slot
use. on remote control
2. Know your pump, its limitations and how it operates before 2. Connect purple hose into air line coupler number 2 on
attempting to use the pump and then put other end of purple hose into
3. Use Spare Parts List Illustration on pages 6 & 8 as reference corresponding slot on remote control.
of location and assembly. 3. Connect white hose to air line coupler number 3 on the
4. Replace shipping plug (red color) with air vent plug (black pump and then put other end of the white hose into
color). Refer to #58 on parts illustration. corresponding slot on remote control.
Note: Always secure threaded port connections with non-
hardening pipe thread compound. Tighten securely to prevent
accidental removal of components while in use. Take care not
to introduce compound into port orifices.

! WARNING
• Study, understand, and follow all • Never attempt to disconnect hydraulic connections under
instructions provided with and on this pressure. Release all line pressure before disconnecting
device before use. hoses.
• All WARNING statements must be • Use only approved accessories and approved hydraulic fluid.
carefully observed to help prevent • Never attach ANY component not authorized by manufacturer.
personal injury. • Always ensure that the chosen application is stable to work
• No alteration shall be made to this on and around.
• Do not connect to application which can return more oil to
device.
the reservoir than the pump reservoir can hold.
• Always wear protective gear when
• Do not connect pump to hydraulic system powered by
operating hydraulic equipment.
another pump.
• Keep hydraulic equipment away from
• This device is not suitable for use as support device! As
flames and heat. Hydraulic fluid can
the system load is lifted, use blocking and cribbing to guard
ignite and burn. Do not operate if
against a falling load.
leaks are detected.
• All personnel must be clear before lowering load or
• Crush Hazard. Keep hands and feet
depressurizing the system.
away from loading area. Avoid pinch
• Never try to disassemble a hydraulic cylinder, refer repairs
points or crush points that can be
to qualified, authorized personnel.
created by the load, cylinder, or any
equipment of system. HYDRAULIC HOSES & FLUID TRANSMISSION LINES
• To avoid crushing and related injuries: • Avoid short runs of straight line tubing. Straight line runs
NEVER work on, under or around do not provide for expansion and contraction due to
a lifted load before it is properly pressure and/or temperature changes.
supported by appropriate mechanical • Reduce stress in tube lines. Long tubing runs should be
means. Never rely on hydraulic supported by brackets or clips. Before operating the pump,
pressure alone to support load. tighten all hose connections with proper tools. Do not
overtighten. Connections should only be tightened securely
HYDRAULIC PUMPS and leak-free. Overtightening can cause premature thread
• The user must be a qualified operator familiar with the failure or high pressure fittings to burst.
correct operation, maintenance, and use of pumps. Lack of • Should a hydraulic hose ever rupture, burst or need to be
knowledge in any of these areas can lead to personal injury. disconnected, immediately shut off the pump and release
• Do not exceed rated capacity of the pump or any equipment all pressure. Never attempt to grasp a leaking pressurized
in the system. hose with your hands. The force of escaping hydraulic fluid
• Never attempt to lift a load weighing more than the capacity can inflict injury.
of the cylinder. • Do not subject the hose to potential hazard such as fire,
• Burst hazard exists if hose or connection pressure exceeds sharp objects, extreme heat or cold, or heavy impact.
rated pressure. • Do not allow the hose to kink, twist, curl, crush, cut or bend
• Do not subject the pump and its components to shock so tightly that the fluid flow within the hose is blocked or
loads. reduced. Periodically inspect the hose for wear.
• Inspect pump, cylinder, hoses and connections before each • Do not pull, position or move setup by the hose.
use to prevent unsafe conditions from developing. Do not • Hose material and coupler seals must be compatible with
use if they are damaged, altered or in poor condition. Do hydraulic fluid used. Hoses also must not come in contact
not operate the system with bent or damaged coupler or with corrosive materials such as battery acid, creosote-
damaged threads. impregnated objects and wet paint. Never paint a coupler
• Never hold or stand directly in line with any hydraulic or hose.
connections while pressurizing. • FAILURE TO HEED THESE WARNINGS MAY RESULT IN
• Use gauge or other load measuring instrument to verify load. PERSONAL INJURY AS WELL AS PROPERTY DAMAGE.
3
 OPERATION MAINTENANCE
! To reduce the risk of personal injury and/or property Important: Use only a good quality hydraulic jack fluid. Never
damage, hydraulic connections must be securely fastened use brake fluid, transmission fluid, turbine oil, motor oil, alcohol,
before building pressure in the system. Release all system glycerin etc. Use of other than good quality hydraulic oil will
pressure before loosening any hydraulic connection in the void warranty and damage the pump, hose, and application.
system. We recommend Mobil DTE 13M or equivalent.

! Always monitor pressure, load or position using 1. Inspect hoses and connections daily. Replace damaged
suitable equipment. Pressure may be monitored by means of components immediately with BVA Hydraulics replacement
an optional manifold and gauge. Load may be monitored by parts only.
means of a load cell and digital indicator. Correct application 2. Tighten connections as needed. Use non-hardening pipe
position can only be determined by the operator of the thread compound when servicing connections.
equipment. 3. Use only good quality hydraulic fluid. We recommend Mobil
DTE 13M or equivalent.
1. Air connection: Remove plug from first or second air input
port (refer to figure 1) and connect to adequate air supply. Adding Hydraulic Fluid
Install hex plug on unused air input port to prevent air 1. Depressurize and disconnect hydraulic hose from
leakage. application.
2. Hydraulic connection: Remove manifold plug from oil 2. With pump in upright, horizontal position, remove the air
output port and connect to suitable application using 3/8 vent plug located on the top plate of the reservoir.
NPT connection. 3. Use a small funnel to fill reservoir to within 3/4" (19mm) of
3. To operate pump, press and hold on the advance button of the opening.
the remote control until desired pressure, load or position 4. Wipe up any spilled fluid and reinstall the air vent plug.
is reached. Always monitor pressure, load or position
using suitable equipment. Pressure may be monitored by Changing Hydraulic Fluid
means of an optional manifold and gauge (contact BVA 1. For best results, change fluid once a year.
Hydraulics). Load may be monitored by means of a load 2. Repeat step 2 on Adding Hydraulic Fluid, then pour used
cell and digital indicator. Correct application position can fluid into a sealable container.
only be determined by the operator of the equipment. 3. Dispose of fluid in accordance with local regulations.
4. To retract application, simply press the retract button on 4. Fill with a good quality hydraulic jack oil as recommended
the remote control. above. Reinstall air vent plug.

Note: Both air input ports use a 1/4 NPT air nipple (not Lubrication
included). It is recommended to install an inline air filter and When pump is operated on daily basis, the manufacturer
dryer upstream from the pump to provide clean, lubricated air. recommends installing an inline oiler and air dryer. Use SAE
Contact BVA Hydraulics for necessary accessories. grade oil (5W to 30W).

Storage
1. When not in use, depressurize and disconnect hydraulic
hoses from application.
2. Wipe clean, thoroughly.
3. Store in clean, dry environment. Avoid temperature
extremes.
4. For transportation or long storage, replace the air vent plug
with shipping plug.
5. Shield pump with a protective cover.

4
 TROUBLESHOOTING GUIDE
The following information is intended as an aid in determining if problem exists. Pumps should be repaired only by authorized
BVA Service Center. For repair service, contact service center in your area.

Symptom Possible Causes Corrective Action

Application does not extend, move or • Overload condition • Remedy overload condition
respond to pressurized fluid • Loose couplers • Tighten couplers
• Faulty couplers • Replace couplers
• Pump malfunction • Contact service center
• Inadequate air supply • Ensure air source can dedicate
7.8 CFM @ 110~175 PSI

Application responds to pressurized • Overload condition • Remedy overload condition

fluid, but system does not maintain • Pump or valve malfunction • Contact Service Center
pressure • Application/connection leaking • Replace application/connection

Application responds slower than • Loose connection or coupler • Tighten connection or coupler
normal • Restricted hydraulic line or fitting • Clean and replace if damaged
• Application/connection leaking • Replace application/connection

Application does not return fluid to • Malfunctioning coupler, damaged ap- • Secure load by other means.
pump (i.e. cylinder will not retract) plication Depressurize pump and hose,
remove coupler and/or application,
then renew or replace

Application does not fully extend (cyl- • Reservoir overfilled • Secure load by other means.
inder or spreader) Depressurize pump and hose,
remove application, then drain fluid to
proper level
• Fluid level in pump is low • Secure load by other means.
Depressurize pump and hose,
remove application, then fill fluid to
proper level

Poor performance • Fluid level in pump is low • Ensure proper fluid level

5
 Air Hydraulic Pump
Service Parts
MODEL: PA1500L
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419 * Fax: 816-891-6599
E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com

Note: Not all components of the pump are replacement items, but are illustrated as a PA1500L-M0
convenient reference of location and position in the assembly sequence. rev 08/07

Parts Illustration

Note: To ensure safe and reliable performance, replace worn or damaged parts with BVA Hydraulics
Authorized Replacement Parts only.
6
 Air Hydraulic Pump
Service Parts
MODEL: PA1500L
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419 * Fax: 816-891-6599
E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com

Note: Not all components of the pump are replacement items, but are illustrated as a PA1500L-M0
convenient reference of location and position in the assembly sequence. rev 08/07

Parts List
Item Part Number Description Qty Item Part Number Description Qty
1 649-1-0050-055 Allen screw (M5X0.8X5L) 10 41 A57-6-2023-108 Bushing 1
2 A57-3-5003-109 Pump handle 1 42 573-7-0120-105 Back-up ring 1
3 649-1-0050-046 Allen screw (M5X0.8X30L) 8 43 * U-cup 1
4 A57-6-5301-105 Release valve, air motor piston1 44 A59-6-1013-105 Pump piston cylinder 1
5 A57-6-5302-107 Release valve piston, 1 45 A57-6-1016-106 Spacer 1
6 * O-ring 1 46 H18-6-8103-104 Crush washer (Steel and rubber)1
7 * Back up ring 1 47 A57-6-1001-204 Base, hydraulic unit 1
8 511-2-0181-103 Compression spring 1 48 A57-6-1605-105 Gasket 1
9 D05-6-1001-106 Manifold plug (oil output port) 1 49 511-7-0140-200 O-ring 2
10 A57-6-3007-105 Noise suppresor 1 50 A57-3-5002-107 Remote control assy. 1
11 666-5-0160-107 C-clip 1 51 A57-6-5309-101 Air hose 1
12 * O-ring 2 52 A17-6-1105-103 Manifold plug, air 1
13 * Back-up ring 2 53 A57-6-2062-108 Air inlet connector (H17x41L,1
14 A57-6-4002-201 Oil discharge valve 1 thread 1/4"-18NPTF both ends)
15 512-2-0043-108 Compression spring 1 54 651-7-0063-007 Air line coupler (H10x20L, 5
16 601-7-0009-001 Steel ball 1 thread 1/8"PT, 1/4" air line)
17 511-7-0410-102 O-ring 1 55 A57-6-5305-103 Air inlet base 1
18 * Copper washer 6 56 642-1-0050-048 Allen screw (M5X0.8X40L) 2
19 A57-6-1603-202 Reservoir top plate 1 57 641-1-0098-103 Hex bolt 1
20 644-1-0060-05311 Set screw 1 58a A57-3-5007-107 Shipping plug (red) 1
21 503-9-0050-106 Steel ball seat 1 58b A57-3-1900-109 Air vent plug (black) 1
22 601-7-0006-005 Steel ball 1 59 512-2-0061-100 Compression spring 1
23 A59-6-1017-102 Pressure relief valve cylinder1 60 644-1-0040-204 Lower assy. bolt, release valve1
24 A17-6-1216-102 Pressure relief valve stem 1 61 512-2-0033-105 Compression spring 1
25 512-2-0067-010 Compression spring 1 62 503-9-0035-100 Steel ball seat 1
26 601-7-0008-009 Steel ball 1 63 601-7-0003-009 Steel ball 1
27 A17-5-1603-300 Pressure relief valve screw 1 64 A57-6-3003-305 Release valve 1
28 532-3-0127-106 Crush washer (steel & rubber)2 65 A57-6-3004-307 Release valve guide 1
29 A59-6-1015-108 Oil intake valve 1 66 * O-ring 1
30 520-8-0134-101 Filter 1 67 * Back-up ring 1
31 * Reservoir gasket 1 68 552-2-0010-105 Compression spring 1
32 A57-6-1601-107 Oil reservoir 1 69 * Release valve pin 1
33 649-1-0060-122 Thru bolt, air motor 4 70 A57-6-3001-112 Release valve cap 1
34 A57-6-1002-105 End plate, air motor 1 71 * O-ring 1
35 A17-6-2105-108 Gasket 2 72 A57-6-1604-103 Gasket 1
36 A17-4-2100-500 Air motor piston 1 73 A17-6-1002-103 Noise suppresor 1
37 A57-6-1003-107 Cylinder, air motor piston 1 74 666-5-0250-108 C-clip 1
38 A57-3-1011-108 Pump piston 1 75 A57-5-4001-102 Oil manifold 1
39 512-2-0410-017 Compression spring 1 76 A57-6-5303-120 Air hose 1
40 A57-6-1014-102 Pump piston guide 1 (*) A57-3-9909-107 Seal kit -
(*) Seal kit includes item #6, 7, 12, 13, 18, 31, 43, 66, 67,
69, 71

7
 Air Hydraulic Pump
Service Parts
MODEL: PA3801L
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419 * Fax: 816-891-6599
E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com

Note: Not all components of the pump are replacement items, but are illustrated as a PA1500L-M0
convenient reference of location and position in the assembly sequence. rev 08/07

Parts Illustration

Note: To ensure safe and reliable performance, replace worn or damaged parts with BVA Hydraulics
Authorized Replacement Parts only.
8
 Air Hydraulic Pump
Service Parts
MODEL: PA3801L
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419 * Fax: 816-891-6599
E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com

Note: Not all components of the pump are replacement items, but are illustrated as a PA1500L-M0
convenient reference of location and position in the assembly sequence. rev 08/07

Parts List

Item Part Number Description Qty. Item Part Number Description Qty.
1 649-1-0050-055 Screw M5x0.8x16L 10 41 A57-6-1014-102 Piston cover 1
2 A57-3-5003-109 Handle 1 42 A57-6-2023-108 Bushing 1
3 649-1-0050-046 Screw M5x0.8x30L 8 43 * Back-up ring 1
4 A57-6-5301-105 Release cylinder 1 44 * U-cup 1
5 A57-6-5302-107 Release piston 1 45 A59-6-1013-105 Pump 1
6 * O-ring 1 46 A57-6-1016-106 Washer 1
7 * Back-up ring 1 47 * Special washer 1
8 511-2-0181-103 Compression spring 1 48 A57-6-1001-204 Base 1
9 D05-6-1001-106 Nut H19x23L 1 49 * Pad B 1
10 A57-6-3007-105 Noise Suppresor 1 50 * O-ring 2
11 666-5-0160-107 C-clip no.16 1 51 A57-3-5002-107 Air control assy. 1
12 * O-ring 2 52 A57-6-5309-101 Air tubes 1
13 * Back-up ring 2 53 A17-6-1105-103 Plastic cover 1
14 A57-6-4002-201 Oil outlet valve 1 54 A57-6-2062-108 Air inlet connector (H17x41L,1
15 512-2-0043-108 Compression spring 1 thread 1/4"-18NPTF both ends)
16 601-7-0009-001 Steel ball 1 55 651-7-0063-108 Coupler 5
17 * O-ring 1 56 A57-6-5305-103 Air entrance base 1
18 649-1-0060-040 Screw M6x1x15L 18 57 642-1-0050-048 Screw M5x0.8x40L 2
19 * Washer 18 58 641-1-0098-103 Screw 1/8” 1
20 A57-6-1603-202 Reservoir cover 1 59a A57-3-5007-107 Shipping plug (red) 1
21 644-1-0060-053 Screw M6x1x6L 1 59b A57-3-1900-109 Air vent plug (black) 1
22 503-9-0050-106 Steel ball block 1 60 512-2-0061-100 Compression Spring 1
23 601-7-0006-005 Steel ball 1 61 A57-4-3003-105 Release Valve 1
24 * Special washer 2 62 A57-6-3004-307 Release base 1
25 A59-6-1017-102 High pressure base 1 63 * O-ring 1
26 A17-6-1216-102 Pin 1 64 * Back-up Ring 1
27 512-2-0067-010 Compression spring 1 65 552-2-0010-105 Compression Spring 1
28 A17-5-1603-300 Pressure adjust nut 1 66 * Release pin 1
29 601-7-0008-009 Steel ball 1 67 A57-6-3001-112 Release bar 1
30 A57-6-6006-108 Oil entrance valve 1 68 * O-ring 1
31 520-8-0134-101 Filter 1 69 * Pad A 1
32 * Packing 1 70 666-5-0250-108 Silencer 1
33 A57-6-6007-201 Reservoir 1 71 A17-6-1002-103 C-clip 1
34 649-1-0060-122 Screw M6xP1x120L 4 72 A57-5-4001-102 Oil outlet base 1
35 A57-6-1002-105 Motor cover 1 73 A57-6-5303-120 Air tube 1
36 A17-6-2105-108 Cylinder washer 2 (*) A57-3-9914-100 Seal kit -
37 A17-4-2100-500 Air piston assy. 1
38 A57-6-1003-107 Cylinder 1 (*) Seal kit includes item #6, 7, 12, 13, 17, 19, 24,
39 A57-3-1011-108 Piston assy. 1 32, 43, 44, 47, 49, 50, 63, 64, 66, 68, 69
40 512-2-0410-017 Compression spring 1

9
 LIMITED LIFETIME WARRANTY

BVA Hydraulics®, represented in the United States by SFA Companies [“SFA”] warrants this product to be free from defects in
material and workmanship for the life of the product as long as the original purchaser owns the product. The warranty is non-
transferable and is subject to the terms, exclusions, and limitations described below:

• Damaged components, including but not limited to bent rams, dented or crushed cylinder walls, broken welds or couplers as
well as worn out seals, o-rings and springs are the result of misuse and not covered by warranty and BVA Hydraulics will not
provide any warranty credit for such damaged components.
• This warranty does not cover ordinary wear and tear, overloading, alterations (including repairs or attempted repairs not
performed by BVA Hydraulics or one of its authorized personnel), improper fluid use, or use of the product in any manner for
which the product was not intended or the use of which is not in accordance with the instructions or warnings provided with
the product.
• In the unlikely event that a BVA Hydraulics product fails due to material defect in workmanship, you may contact SFA for
disposition. In such cases, the customer’s sole and exclusive remedy for any breach or alleged breach of warranty is limited
to the repair or replacement of the defective product.
• Under no circumstances is BVA Hydraulics liable for any consequential or incidental damage or loss whatsoever.
• THIS WARRANTY IS LIMITED TO NEW PRODUCTS SOLD THROUGH AUTHORIZED DISTRIBUTORS AND OTHER
CHANNELS DESIGNATED BY BVA HYDRAULICS. NO AGENT, EMPLOYEE OR OTHER REPRESENTATIVE OF BVA
HYDRAULICS IS AUTHORIZED TO MODIFY THIS WARRANTY.
• THE FOREGOING IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FOR A FITNESS FOR A PARTICULAR
PURPOSE.
• Components not manufactured by BVA Hydraulics including certain motor systems, gasoline engines, and others are not
covered by this warranty and instead are covered by the manufacturer’s separate manufacturer’s warranty provided in the
package.
• BVA Hydraulics’ liability in all cases is limited to, and will not exceed the purchase price paid for the product.

SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419
E-mail: sales@bvahydraulics.com
10
 SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419
E-mail: sales@bvahydraulics.com
 SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419
E-mail: sales@bvahydraulics.com