Persta Industrie e

Valves for the industry
Globe valves
n Gate valves
n Swing check valves
n
6100.1.05.14
Prolog
Industrial valves made by company Stahl-Armaturen

PERSTA GmbH are designed according to DIN-Standards,
EN-Standards and according to the technical rules like
AD and the European Pressure Vessel Guideline 97/23/EG.
Design, manufacture and testing of these valves was
carried out on condition that the valves are operated
under normal operating conditions. Normal operating
conditions contain for example the following:
If the purchaser expects stresses deviating from the

normal operating conditions he has to indicate these
requirements unambiguously and completely in the
inquiry as well as in the order. This would allow us,
as the valve manufacturer, to work out corresponding
measures and to suggest them to the customer. These
measures could be for example:
Special choose of the body material
Higher wall-thickness
n Protection of areas which are endangered by wear
n Special gaskets and bolt connections
n Special operation instructions depending on the
medium and the kind of operation
n Special coatings
n Additional equipment to avoid excessive overpressure
n Special design for control operation, etc
n
n
Operation with liquid or gaseous media, without special

corrosive, chemical or abrasive influences.
n Frequency of temperature-change of app. 3 6 K
per minute.
n Usual flow rates, depending on the kind of medium and
the range of application of the valve.
n Operation without additional outer influences like
pipeline-forces, vibrations, wind load stressing,
earthquake, corrosive environment, fire, operation load
stressing, disintegration pressure of unstable fluide, etc.
n
During planning and installation of the pipeline the

customer should take measures which minimize
additional dangers and pressures on the valves, on the
piping system and on the environment, for example by:
Installation of vibration dampers
Consideration of a security final position in case of
break down of energy
n Taking measures to ensure the safe drainage of
dangerous media in case of leakage, etc
n
n
Please see our relevant Instruction Operational

Maintenance manual for further information and
warnings which have to be considered for the
operation of industrial valves.
Imprint
Copyright in and to this documents shall remain with
Stahl-Armaturen PERSTA GmbH.
Duplication, application or notification to a third party
is forbidden, criminal and institute legal proceeding
(German Copyright Act, UWG, BGB). All rights, including
rights created by patent grant or registration of a utility
model, are reserved.
Technical alterations reserved
6100.1.05.14
Table of content
Designation
Type
Size
Rating
Page
Globe valves
Gobe
valve
200 AE/BE/AJ/BJ
DN 10-50
PN 10-160
1-4
Lift check valve
240 MT
DN 10-50
PN 10-160
1-4
Globe valve
200 AE/BE/AJ/BJ
DN 65-200
PN 10-160
5-8
Lift check valve
240 MT
DN 65-200
PN 10-160
5-8
Bellow seal globe valve / VALTRA
200 AL
DN 15-400 (200)
PN 10-160
9-10
High pressure globe valve HD 91
200 JM
DN 10-65/50
PN 320
11-14
200 LM/202 LM
DN 10-65
PN 500
15-20
200 LS/200 LJ
DN 10-65
PN 500
15-20
240 MT
DN 10-65
PN 500
15-20
Stop check valve HD 2000
240 MM
DN 10-65
PN 500
15-20
High pressure globe valve DVA 25/40
200 BZ
DN 80-250
PD 25/40
21-24
with back seat

High pressure lift check valve
HD 2000
Further standards
25-26
Special globe valve variants
27-28
Gate valves
Small
gate valve
808 GJ
DN 10-40
PN 10-100
Small gate valve / VALTRA
800/808 GJ
NPS 1/2 - 2 / DN 15-50 Class 800/10-40
33-36
Gate valve
700 HJ/JJ (GA)
DN 50-150
PN 10-100
37-42
Gate valve
700 HJ/JJ (GA)
DN 200-250
PN 10-40
43-46
Gate valve
700 HJ/JJ
DN 200-300
PN 63-100
47-50
Gate valve
400 JJ
DN 350-700
PN 63-100
51-54
Gate valve / VALTRA
700 JJ
DN 300-1000
PN 10-25
55-56
Gate valve / VALTRA
700 JJ
DN 300-700
PN 40
57-58
Gate valve
700 JJ
DN 50-300 / 250
PN 160/PD 18
59-62
High pressure gate valve DSK 10
700 JT
DN 50-150
PD 10
63-66
700 JT
DN 200-350 / 300
PD 10
67-70
700 JT
DN 350-700
PD 10
71-74
700 JT
DN 65-300
PD 25/40
75-78
High pressure gate valve DSK 16 - 63
700 JT
DN 50-600
PD 16-63
79-82
Overpressure-safety-devices /
29-32
83-84
PERSTA Type SV 97, -98, -99

Gate valve variants
6100.1.05.14
85-86
Designation
Type
Size
Rating
Page
Swing check valves
Swing check valves

640 AA
DN 50-250
PN 10-40
Swing check valves/VALTRA
640 AA
DN 300-800
PN 10-40
Swing check valves
640 AA
DN 50-300 / 250
PN 63-160 (PD 18)
High pressure swing check valves DRI 26
640 AB
DN 65-300
PD 25 / 40
High pressure swing check valves DRI 16 - 63 640 AB
DN 50-600
PD 16-63
High pressure
640 ST
PD 25 / 40
stop check valves DRA 26
Freewheel swing check valve
640 DJ
DN 50-800
PN 40-250
Swing check valves variants
109
110
Line blind valves
Line
blind valves DPV 10
Line blind valves DPV 16-63
87-90
91-94
95-98
99-102
103-106
107-108
990 VW
DN 350-700
PD 10
111-114
990 VW
DN 65-600
PD 16-63
115-118
Strainer
Strainer
990 ST
DN 10-65
PN 500
119-122
Strainer
DSF
990 ST
DN 80-250
PD 25 / 40
123-124
Technical appendix
Pressure-rate-tables
PD 10-63
125
Flange dimensions
126
Design
127-128
Butt welding ends DIN 3239 and 2559
129
Butt welding ends EN 12627
130
Processing and test equipment/test facilities
131
Qualification/approvals
132
Figure number code
133
Notice
The values indicated in the operating pressure and temperature tables are the max. admissible operating data for our
valves. Before choosing a valve, the plant-specific extent of variations of the pressure and temperature as well as
possible emergency conditions have to be considered
6100.1.05.14
Globe valves
Globe valve
Globe valves
Lift check valve
200 AE/BE/AJ/BJ
n
240 MT
PN 10-160
PN 10-160
DN 10-50
DN 10-50
Range of application
Admissible operating pressure [bar] at design temperature [C] 1)
Material PN -200 -60 -10 20 120 150 200 250 300 350 400 450 500 510 520 530 540 550
1.0460
10-40 40 40 40 37 35 32 28 24 21 10
63 63 63 63 58 50 45 40 36 32 24
100 100 100 100 90 80 70 60 56 50 38
160 160 160 160 145 130 112 96 90 80 60

10-40 40 40 40 40 40 40 35 31 30 28 18 14 11 9
1.5415 5)
63 63 63 63 63 63 63 56 50 47 45 29 22 16 14
100 100 100 100 100 100 100 87 78 74 70 45 34 27 22
160 160 160 160 160 160 160 139 125 118 112 72 55 43 35

1.7335 10-40 40 40 40 40 40 40 40 38 36 34 29 24 19 15 12 9
63 63 63 63 63 63 63 63 61 58 56 47 40 32 25 20 15
100 100 100 100 100 100 100 100 95 91 87 74 62 49 38 31 24
160 160 160 160 160 160 160 160 153 146 139 118 100 79 62 46 35

1.4571
10-40 2)3)4) 40 40 40 40 40 40 40 40 38 36 34 32 32 32 31 31 31 31

63 2)3)4) 63 63 63 63 63 59 56 53 50 48 47

100 2)3)4) 100 100 100 100 100 92 88 83 79 76 73

160 2)3)4) 160 160 160 160 160 150 142 135 127 123 119

1.0566 10-40 4)6) 40 40 40 40 37 35 32 28

63 4)6) 63 63 63 63 58 50 45 40

100 4)6) 100 100 100 100 92 80 70 60

160 4)6) 160 160 160 160 147 130 112 96

1) Operating temperature = design temperature minus temperature surcharge acc. to DIN regulations.
2) Application at more than 400 C operating temperature only admissible if no intercrystalline corrosion has to be expected.
3) At operating temperature 400 C the material of the screws is 1.4986.
4) In case of screws A4-70 with > 8 x d screw-length the mechanical strength properties acc. to table 6 of DIN 267 Part 11 have been considered.
5) Butt welding ends
6) At temperature > 50 C only applicable for short-time service.
6100.1.05.14
Globe valves
Globe valve
Globe valves
Lift check valve
200 AE/BE/AJ/BJ
n
240 MT
PN 10-160
Standard features
n
n
n
n
n
n
n
n
n
n
PN 10-160
Straight body
Die-forged valve body and bonnet
Shut-off disc, Fig. No. 200 AE
Shut-off disc with yoke sleeve, standard features AJ
Trottle disc with yoke sleeve, standard features BJ
Trottle disc standard features BE
Outside screw and yoke
Position indicator if required
Turning and rising stem (AE/BE)
Non-turning, rising stem (AJ/BJ)
DN 10-50
DN 10-50
Media
Depending on the material the valves are suitable for
water, gas, oil and other non aggressive media
Fields of application
Chemical industries, power plants, ship building and
other
Pressure and temperature ratings

n
n
n
Pressure rating BW-Ends up to 160 bar

Pressure rating FL up to 160 bar
Temperature rating up to 550 C
Materials
n
n
n
n
n
1.0460
1.0566
1.5415 only with BW-Ends
1.7335
1.4571
Further materials on request.
Design Highlights
Benefits
Free from porosity and shrink holes
Seats are hardfaced or welded on
Extremely resistant to wear
Body-bonnet connection male and female
Sealing blow out proof

Body and bonnet in two separate pieces with bolted
connection
To ease maintenance work, e.g. regrinding

of the body seats
6100.1.05.14
Globe valves
Globe valve
Globe valves
Lift check valve
200 AE/BE/AJ/BJ
n
240 MT
PN 10-160
PN 10-160
DN 10-50
Zeichnungs-Nr.: Angebot/1/0
DN 10-50
DN 25
PN 160
Aufsatz-Ventil - 200 AE 25.1
Globe
valve AJ/BJ
Erstellt
01.08.2013 SYSTEM
Globe valve AE/BE
Geprft
D
Artikel-N
Revision
01.08.2013 BECKER
STAHL-ARMATUREN PERSTA GmbH, POSTFACH 2240, 595
Eigenschaften
610
609
511
600
510
Anschluss Austritt
Flansch DIN 2501
Anschluss Eintritt
Flansch DIN 2501
Form des Anschlusses am Austr.

Form des Anschlusses am Eintr.
Dichtl. EN 1092-1 Form B2

Dichtl. EN 1092-1 Form B2
Gewicht [kg]
12
590
710
260
220
180
463
12
462
450
420
200
170
190
160
400
300
100
= Ersatzteilempfehlung
440
Mae Armatur
L
464
500
Mae Antrieb
PosNr Art.Nr. Bezeichnung

100
160
170
190
200
300
400
420
440
450
462
463
464
500
501
600
609
610
202406
100665
120672
122135
107041
110030
116034
118714
111525
114653
121207
114080
109571
107015
108569
108703
114581
111074
Werkstoff
Gehuse DV 160/25
Dichtring
Stiftschraube
Sechskantmutter
Bgeldeckel V 160/25
Kegel 25
Spindel
Packungshlse
Stopfbuchsbrille 16
Nietstift
Klappschraube
Scheibe
Sechskantmutter
Spindelmutter
Zylinderstift
Handrad 12/180
Scheibe
Sechskantmutter
H2
501
1.0566, Sitz
Grafit
A4-70
A4-70
1.0566
1.0566, Sitz
1.4571
Grafit
1.4571
A4-50
1.4571
A4-50
A4-70
1.0718
Stahl
5.3106
Stahl
1.1181
Technische nderungen vorbehalten
Lift check valve
210
190
BW-Version
170
160
330
H1
304
100
L
L
6100.1.05.14
Globe valves
Globe valve
Globe valves
Lift check valve
200 AE/BE/AJ/BJ
n
240 MT
PN 10-160
PN 10-160
DN 10-50
DN 10-50
Materials

Pos. Component
1.0460 (21) 9)
1.0566 (25)

1.0566 4)
100 Body
1.0460 4)8)
160
4 Gasket
Graphite
Graphite
1.1181
A4-70
170 Stud 1)
1.7709
A4-70
170 Stud 2)
1)
1.1181
A4-70
190 Hexagonal nut
1.7218
A4-70
190 Hexagonal nut 2)
200 Bonnet
1.0460
1.0566
210 Bonnet
1.0460
1.0566
4Disc
1.4021 3)
1.0566 4)
300
304
4 Disc
1.4021 3)
1.4571 6)
330
4 Spring
1.4310
1.4310
4 Stem
1.4021
1.4571
400
4 Packing
Graphite
Graphite
420
440 Gland flange
1.0460
1.4571
450 Rivet
1.1181
A4-50
462 Gland bolt
1.1181
1.4571
463 Washer
St
A4-50
464 Hexagonal nut
1.1181
A4-70
4 Stem nut
1.0718
1.0718
500
4 Cylindrical pin
St
St
501
4 Yoke sleeve
1.0718
1.0718
510
4 Needle bearing
WLSt
WLSt
511
590 Grease nipple
5.8
5.8
600 Handwheel
5.3106
5.3106
609 Washer
St
St
610 Hexagonal nut
1.1181
1.1181
710 Anti-rotation device
5.3106
5.3106
BW-Version
1.5415 (42)
1.7335 (44)
1.4571 (82)
1.4571 (87)
1.5415 5)
Graphite
1.7709
1.4923
1.7218
1.7218
1.7335
1.7335
1.7335 5)
1.4571 5)
1.4310
1.4021
Graphite
1.0460
1.1181
1.1181
St
1.1181
1.0718
St
1.0718
WLSt
5.8
5.3106
St
1.1181
5.3106
1.7335 5)
Graphite
1.7709
1.4923
1.7218
1.7218
1.7335
1.7335
1.7335 5)
1.4571 5)
1.4310
1.4021
Graphite
1.0460
1.1181
1.1181
St
1.1181
1.0718
St
1.0718
WLSt
5.8
5.3106
St
1.1181
5.3106
1.4571 7)
Teflon
A4-70
A4-70
A4-70
A4-70
1.4571
1.4571
1.4571 6)
1.4571 6)
1.4571
1.4571
Teflon
1.4571
A4-50
1.4571
A4-50
A4-70
1.0718
St
1.0718
WLSt
5.8
5.3106
A4-50
A4-70
5.3106
1.45717)
Graphite
A4-70
A4-70
A4-70
A4-70
1.4571
1.4571
1.45716)
1.45716)
1.4571
1.4571
Graphite
1.4571
A4-50
1.4571
A4-50
A4-70
1.0718
St
1.0718
WLSt
5.8
5.3106
A4-50
A4-70
5.3106
4 Spare parts
Special materials on request; alterations reserved.
1) PN 10-40
2) PN 63-160
3) Seat hard faced
4) Seat hard faced with Cr17

5) Seat hard faced with Stellite
6) PN 63 seat hard faced with Stellite
7) PN 63 seat hard faced with hastelloy

8) DN 50 PN 63-160 material 1.0619 hard faced with Cr17
9) DN 50 PN 10-40 Flange Version with 1.0619 hard faced with Cr17
Dimensions/mm

FL
BW
PN
DN
L
L
H
H1
10-40

63-160

63-100
160
10
15
20
25
32
40
50
10
15
20
25
32
40
50
50
130
130
150
160
180
200
230
210
210
230
230
260
260
300
300
130
130
130
130
160
180
210
150
150
150
160
180
210
250
250
215
215
220
220
245
250
260
220
220
220
220
285
285
285
285
85
85
90
90
115
130
120
100
100
100
100
140
140
150
150
Weights/kg

Stroke
1.0619
H2
h
D1
H
275
275
275
275
305
305
345
275
275
275
275
335
335
345
345
12
12
12
12
15
15
18
12
12
12
12
15
15
18
18
140
140
140
140
180
180
180
180
180
180
180
225
225
150
225
260
260

200 AE/BE

PN
DN
FL
BW

10-40
10
4,5
3,8

15
5,0
4,2

20
5,7
3,8

25
6,3
4,0

32
10,0
7,3

40
11,2
7,3

50
15,5
11,0
63-160
10
8,7
5,9

15
8,6
6,2

20
10,4
5,5

25
10,9
5,8

32
19,0
13,2

40
21,0
12,8
63-100
50
24,1
15,0
160
50
25,0
15,0
240 MT

FL
BW
3,2
3,2
3,9
4,7
7,9
9,1
12,1
6,0
6,8
9,0
9,2
15,6
16,8
19,5
22,0
2,4
2,4
2,4
2,3
5,5
5,5
7,9
4,0
4,0
4,0
4,0
9,0
9,0
11,0
11,0
The valves are also available in angle pattern up DN 100.
Kvs-values (m3/h)

Line
DN 10
DN 15
DN 20
PN 10-40
DN 25
200 AE (BW)
3,0
4,5
6,2
8,6
16,0
21,0
30,0
3,0
4,5
6,2
8,6
16,0
21,0
30,0
200 AE (FL)

1,8
3,0
5,3
8,6
13,0
21,0
37,2
1,8
4,5
5,3
8,6
13,0
21,0
37,2
200 BE (BW)
2,8
4,2
5,9
7,6
14,5
19,5
26,9
2,8
4,2
5,9
7,6
14,5
19,5
26,9
200 BE (FL)

1,5
2,8
4,9
7,6
11,2
19,5
34,5
2,8
4,2
5,9
7,6
14,5
19,5
34,5
240 MT (BW)
2,7
4,1
5,7
7,9
14,6
19,2
34,0
2,7
4,1
5,7
7,9
14,6
19,2
34,0
240 MT (FL)
1,7
2,7
5,7
7,9
11,9
19,2
25,8
1,7
2,7
5,7
7,9
11,9
19,2
25,8
DN 32
DN 40
DN 50
DN 10
DN 15
DN 20
PN 63-160
DN 25
DN 32
DN 40
DN 50
6100.1.05.14
Globe valves
Globe valve
Globe valves
Lift check valve
200 AE/BE/AJ/BJ
n
240 MT
PN 10-160
PN 10-160
DN 65-200
DN 65-200
Material PN -200 -50 -10 20 100 120 150 200 250 300 350 400 425 450 475 500 510 520 530 540 550
1.0619 10-16
25
40
63
100
160 3)
16
25
40
63
100
160
16
25
40
63
100
160
16
25
40
63
100
160
16
25
40
63
100
160
15
23
37
53
83
135
14
22
35
50
80
130
13
20
32
45
70
112
11
17
28
40
60
96
10
16
24
36
56
90
1.5419 10
25
40
63
100
160 3)
10
25
40
63
100
160
10
25
40
63
100
160
9
23
36
59
92
148
9
23
36
59
92
148
9
22
35
58
90
143
8
20
31
51
80
128
7
19
29
48
74
119
7
17
27
45
69
111
7
16
26
42
65
104
1.7221 10-16 2)
25 2)
40 2)
63 2)
100 2)
160 2)
16
25
40
63
100
160
16
25
40
63
100
160
16 15,1
25 23,6
40 37,7
55 54
87 84
140 136
15
23
37
53
83
135
14
22
35
50
80
130
13
20
32
45
70
112
16
25
40
63
100
160
8
13
21
32
50
80
6
16
25
41
63
101
6
16
24
40
62
100
6
15
24
39
61
98
6
15
23
38
59
94
3
9
14
22
35
55
3 2 2
7 6 4
11 9 7
18 14 12
28 22 18
44 35 29
11
17
28
40
60
96
1.7357 10-16 16 16 16 16 15 14 13 11 10 8
25 25 25 25 25 25 25 25 25 24 23 22 21 20 18 15 12 9
40 40 40 40 40 40 40 40 40 38 36 35 34 33 29 24 19 15
63 63 63 63 63 63 63 63 63 61 58 57 56 51 47 40 32 25
100 4) 100 100 100 100 100 100 100 100 95 91 89 87 80 74 62 49 38

1.4308 10-16 16 16 16 16 13 12,6 12 11 8 8
25 25 25 25 25 21 19,8 18 17 13 12
40 40 40 40 40 34 32,4 30 24 21 20
1.4581 10-16 16 16 15 14,6 14 13 13 12 12 11 10 8 7,5 7 7 7 7 7 6,5
25 25 25 24 23,2 22 21 20 19 18 17 16 13 12,5 12 11 11 11 11 11
40 40 40 38 36,8 35 33 32 30 28 26 24 21 20 19 19 19 19 18 18

Permissible differential pressure (pressure
inlet below the disc) acc. to EN 13709.
3) PN 160 is only valid for DN 65-100.
4) Only for globe valves DN 65-80; for lift check valves DN 65-125.
6100.1.05.14
Globe valves
Globe valve
Globe valves
Lift check valve
200 AE/BE/AJ/BJ
n
240 MT
PN 10-160
Standard features
n
n
n
n
n
n
n
n
n
n
PN 10-160
Straight bonnet
Cast steel body and bonnet
Shut-off disc, Fig. No. AE
Shut-off disc with yoke sleeve standard features AJ
Throttle disc with yoke sleeve standard features BJ
Throttle disc, Fig. No. 200 BE
Position indicator if required
Turning and rising stem (AE/BE)
Non-turning, rising stem (AJ/BJ)
DN 65-200
DN 65-200
Media
Depending on the material the valves are suitable for
Chemical industries, power plant, ship building and other

n
n
n
Pressure rating BW-Ends up to 160 bar

Materials
n
n
n
n
n
n
1.0619
1.5419
1.7221
1.7357
1.4581
1.4308
Design Highlights
Benefits
Seats are welded on
Sealing blow out proof
Body and bonnet in two pieces with bolted connection
6100.1.05.14
Globe valves
Globe valve
Globe valves
Lift check valve
200 AE/BE/AJ/BJ
n
240 MT
PN 10-160
PN 10-160
DN 65-200
DN 65-200
Globe valve AE/BE
Globe valve AJ/BJ
610
609
600
501
500
464
463
462
440
450
420
200
190
170
160
400
314
310
300
100
510
511
710
H2
590
Lift check valve
BW-Version
190
210
170
160
H1
330
304
100
6100.1.05.14
Globe valves
Globe valve
Globe valves
Lift check valve
200 AE/BE/AJ/BJ
n
240 MT
PN 10-160
PN 10-160
DN 65-200
DN 65-200
Materials
Pos. Component
1.0619 (11)
1.5419 (32)
1.7221 (31)
1.7357 (34)
1.4581 (72)

1.5419 5)
1.7221
1.7357 5)
1.4581 9)
100 Body
1.0619 4)
160
4 Gasket
Graphite
Graphite
Graphite
Graphite
Teflon
Stud 1)
1.1181
1.7709
A4-70
1.7709
A4-70
170
Stud 2)
1.7709
1.4923
A4-70
1.4923
170
1)
Hexagonal nut
1.1181
1.7218
A4-70
1.7218
A4-70
190
Hexagonal nut 2)
1.7218
1.7218
A4-70
1.7218
190
Bonnet
1.0619
1.7357
1.7221
1.7357
1.4581
200
Cover
1.0460
1.7335
1.0566
1.7335
1.4571
210
4 Disc
1.4021 3)
1.7335 5)
1.0566 4)
1.7335 5)
1.4571 8)
300
304
4 Disc
1.0460 3)
1.7335 5)
1.0566 4)
1.7335 5)
1.4571 8)
310
4 Filling piece
1.0035
1.0035
1.0035
1.0035
1.4571
4 Disc nut
1.0050
1.0050
1.0050
1.0050
1.4571
314
4 Spring
1.4310
1.4310
1.4310
1.4310
1.4571
330
4 Stem
1.4021
1.4021
1.4571
1.4021
1.4571
400
4 Packing
Graphite
Graphite
Graphite
Graphite
Teflon
420
440 Gland flange
1.0460
1.0460
1.4571
1.0460
1.4571
450 Rivet
1.1181
1.1181
A4-50
1.1181
A4-50
462 Gland bolt
1.1181
1.1181
1.4571
1.1181
1.4571
463 Washer
St
St
A4-50
St
A4-50
464 Hexagonal nut
1.1181
1.1181
A4-70
1.1181
A4-70
4 Stem nut
1.0718
1.0718
1.0718
1.0718
1.0718
500
4 Cylindrical pin
St
St
St
St
St
501
4 Yoke sleeve
1.0718
1.0718
1.0718
1.0718
1.0718
510
4 Bearing
WLSt
WLSt
WLSt
WLSt
WLSt
511
590
Grease nipple
5.8
5.8
5.8
5.8
5.8
600 Handwheel
5.3106
5.3106
5.3106
5.3106
5.3106
600 Handwheel
5.3106
5.3106
5.3106
5.3106
5.3106
609 Washer
St
St
St
St
A4-50
610 Hexagonal nut
1.1181
1.1181
1.1181
1.1181
A4-70
710 Anti-rotation device
5.3106
5.3106
5.3106
5.3106
5.3106
4 Spare parts
1.4308 9)
Graphite
A4-70
A4-70
1.4308
1.4571
1.4571 8)
1.4571 8)
1.4571
1.4571
1.4571
1.4571
Graphite
1.4571
A4-50
1.4571
A4-50
A4-70
1.0718
St
1.0718
WLSt
5.8
5.3106
5.3106
A4-50
A4-70
5.3106
Special materials on request; alterations reserved.
1) PN 10-40
2) PN 63-160
3) Seat hard faced DN 125, 1.0460 seat hard faced with Cr17
4) Seat hard faced with Cr17

9) PN 63 seat hard faced with hastelloy
5) Seat hard faced with stellite
8) PN 63 seat hard faced with stellite
Dimensions/mm
Weights/kg

FL
BW Stroke
PN
DN
L
L
H
h
H1
D1
H2
10-40

105
115
140
145
170
240
225
280
280
360
360
450
330
390
400
495
530
575
63-160
65
340
340
360
22
120

80
380
380
400
25
145

100
430
430
410
30
165

63
125
500
500
535
40
210

150
550
550
555
50
235

100
125
500
500
535
40
210

150
550
550
555
50
235

280
280
360
360
400
410
360
450
535
555
360
450
535
555
65
80
100
125
150
200
1.4308 (77)
290
310
350
400
480
600
290
310
350
400
480
600
310
360
400
465
530
575
22
25
30
40
50
65

DN

65
80
100
125
150
200
PN
10-16
FL

27,5
37,0
52,0
69,0
103,0
171,0
PN
25-40
FL

27,5
37,0
53,0
69,0
110,5
175,0
PN
10-40
BW

DN
PN
10-16
FL
PN
25-40
FL
PN
10-40
BW
PN
63
FL
65
80
100
125
150
200
18,5
29,6
35,4
58,0
80,0
145,0
18,5
29,6
35,4
58,0
80,0
160,0
11,5
20,4
29,0
40,0
65,0
148,0
29,0
42,0
63,0
101,0
145,0
PN
63
FL
200 AE / BE
PN
PN
63
100
BW
FL
16,0
34,0
24,0
34,0
28,0
47,0
36,0
47,0
41,0
72,0
56,0
72,0
55,0
117,0
93,0
120,0
97,0
160,0
125,0
166,0
156,0
240 MT
PN
63
BW
13,0
23,0
38,0
78,0
110,0
PN
100
FL
29,0
42,0
63,0
106,0
150,0
PN
100
BW
PN
160
FL
PN
160
BW
24,0
36,0
56,0
93,0
125,0
39,0
51,0
80,0
24,0
36,0
56,0
PN
100
BW
PN
160
FL
PN
160
BW
13,0
33,0
23,0
46,0
38,0
71,0
78,0
110,0
13,0
23,0
38,0
Kvs-values (m3/h) BW- and FL-version

Line
DN 65
DN 80
DN 100
DN 125
DN 150
DN 200
PN 10-160 PN 10-160 PN 10-160 PN 10-160 PN 10-160 PN 10-40
200 AE / AJ
71,0
122,0
162,0
260,0
370,0
660,0
200 BE / BJ
61,5
78,0
104,0
171,0
250,0
422,0
240 MT
72,1
105,9
171,6
263,0
374,0
688,0
The valves are also available in angle pattern up to DN

100 nominal sizes > DN 200 on request.
Permissible differential pressure (pressure

inlet below the disc) acc. to EN 13709.
DN 65 80 100 125 150 200

bar 110 70 44 33 21 14
6100.1.05.14
Globe valves
VALTRA Bellow seal globe valve
200 AL
PN 10-160
Globe valves
200 AL
PN 10-40 (63-160)
DN 15-50
n
DN 65-400 (DN 65-200)
DN 15-50
DN 65-400
6100.1.05.14
Globe valves
200 AL
PN 10-160
Globe valves
200 AL
PN 10-40 (63-160)
DN 15-50
n
DN 65-400 (DN 65-200)
Materials

Component

Body

welded on with

Bonnet

Disc

welded on with

Bellow seal

Gasket

Bolt

Hexagonal nut

Stuffing box

Gland flange

Stem upper part

Stem lower part

Handwheel

1)
2)
3)
4)
5)
6)
1.0619
1.4408
1.0619
1.4408
Stellite
1.4370 1)
1.0619
1.4408 / 1.4571
2)
1.4571
1.4021
Stellite
1.4021 1)
1.4571
1.4571
1.4571 Graphite layer
A2-70 5)
A2-70 3)
A2-70 4)
A2-70 5)
Pure graphite
1.4408
1.4408 6)
1.4122
1.4122
1.4571
1.4571
0.6020
0.6020
1.1138
1.1138
1.4370 1)
1.1138 / 1.0566
1.4571 / 1.0566
Stellite
1.4571
A2-70 5)
A2-70 5)
1.4408
1.4122
1.4571
0.6020
PN 63 Stellite
PN 63 1.4571
PN 63 1.7709
PN 63 1.7218
PN 63 A4-70
DN 65 1.0420
Dimensions/mm

FL
BW
PN
DN
L
L H/open
D

40
15
130
130
290
150

20
150
130
290
150

25
160
130
300
150

32
180
160
335
175

40
200
180
340
175

50
230
210
360
200

65
290
290
460
200

80
310
310
610
250

100
350
350
610
300

125
400
400
615
300

150
480
480
645
400

200
600
600
910
400

250
730
730
1280
600

300
850
850
1285
600

350
980
980
1675
600

400
1100
1100
1685
600

63
15
210
210
300
150

20
230
230
300
150

25
230
230
300
150

32
260
260
335
175

40
260
260
340
175

50
300
300
360
200

65
340
340
460
200

80
380
380
610
300

100
430
430
610
300

125
500
500
615
300

150
550
550
945
400

200
650
650
910
400

100-160 15
210
210
375
175

20
230
230
375
175

25
230
230
375
175

32
260
260
410
250

40
260
260
410
250

50
300
300
560
250

65
340
340

80
380
380
880
400

100
430
430
880
400

125
500
500
890
400
100

150
200
550
650
550
650
1080
1045
400
400
160

150
200
550
650
550
650
1140
1140
400
400
Weights/kg

PN
DN
FL
BW

40
15
7
6

20
8
7

25
8
7

32
12
10

40
14
11

50
17
13

65
26
18

80
40
30

100
56
38

125
86
72

150
155
130

200
255
215

250
393
325

300
492
444

350
800
720

400
1020
890
6100.1.05.14
10
Globe valves
200 JM
PN 320
DN 10-65/50
ASME
version
available
Material PN -10 20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 5802) 5902) 6002)

1.0460 160 160 160 160 160 160 160 151 132 118 99 80 76 73 69 65 61 54 45 37
250 250 250 250 250 250 250 235 206 184 155 125 119 113 107 102 96 85 71 58
320 320 320 320 320 320 320 302 264 236 198 160 153 145 138 130 123 109 91 75
1.5415 160 192 192 192 192 192 192 179 165 141 137 132 131 130 129 128 127 126 125 124 109 85 64 51 41
250 300 300 300 300 300 300 280 258 221 213 206 205 203 202 200 199 197 196 194 170 132 101 79 64
320 320 320 320 320 320 320 320 320 283 273 264 262 260 258 256 255 253 251 249 217 170 129 102 81

1.7335 160 192 192 192 192 192 192 192 189 174 165 156 154 152 150 148 146 145 144 143 142 129 109 86 70 57 44 36 29
250 300 300 300 300 300 300 300 294 272 258 243 240 237 234 231 228 227 225 224 222 202 170 134 109 88 69 57 46
320 320 320 320 320 320 320 320 320 320 320 311 307 304 300 296 292 290 289 287 285 258 217 172 140 113 88 72 59

1.7383 2) 160 192 192 192 192 192 192 192 192 189 174 165 163 161 159 157 156 154 152 150 143 127 111 97 85 74 64 55 48 41 36 32
250 300 300 300 300 300 300 300 300 294 272 258 255 252 249 246 243 240 237 234 224 199 174 152 132 115 100 85 75 65 56 49
320 320 320 320 320 320 320 320 320 320 320 320 320 320 319 315 311 307 304 300 287 255 223 194 170 147 128 109 96 83 72 63

2) For temperatures > 570 C, stem in 1.4923 and hightemperature-packing.
11
6100.1.05.14
Globe valves
Standard features
n
n
n
n
n
n
n
Disc and stem in one piece

Die-forged valve body
Non-turning, rising stem
Position indicator
Throttle disc
Yoke sleeve supported by needle bearings
Possibility to add an actuator-flange
200 JM
PN 320
DN 10-65/50
Media
Depending on the material the globe valves are suitable
for water, gas, oil and other non aggressive media
High temperature steam and water, refining (catalytic
reformers and hydrocrackers), petrochemical and chemical industries, power plants

n
n
Pressure rating 320 bar

Temperature rating from -10 C up to 600 C
Materials
n
n
n
n
1.0460
1.5415
1.7335
1.7383
Design Highlights
Body seat: edge seat welded on integratedly
with stellite
Disc / stem single piece of material

> 570 C with stellited edge seat
Sealing to the outside only means

of the gland packing
Body and bonnet in two separate pieces with

bolted connection

(axial type)
Benefits
No pressed in or screwed seat ring, therefore no
crevice corrosion or loosening
No damages between disc and stem

because of high flow velocity
No bonnet gaskets, therefore reduction of possible

leakage areas
To ease maintenance work, e.g. regrinding of the

body seats

n To minimize the expenditure of effort when
operating valve

n Simple retrofitting of an electric actuator possible
n
6100.1.05.14
12
Globe valves
619
619
610
610
613
613
600
600
531
531
511
511
510
510
200
200
716
716
448
448
440
440
420 421
420 421
412
412
400
400
100
100
13
6100.1.05.14
200 JM
PN 320
DN 10-65/50
590
590
464
464
463
463
462
462
192
192
172
172
Globe valves
200 JM
PN 320
DN 10-65/50
Materials
Pos. Component

100 Body
welded on with
172 Stud
192 Hexagonal nut
200 Bonnet
4Stem
400
412 Guide sleeve
420 / 421 4Packing
440 Gland flange
4Dirt scraper
448
462 Stud
463 Washer
464 Hexagonal nut
4Yoke sleeve
510
4Bearing
511
531 Screwing
590 Grease nipple
600 Handwheel
610 Hexagonal nut
613 Screw pin
619 Lock washer
4Tension pin
716
1.0460 (21)
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.0460
Stellite
1.7709
1.7218
1.7379
1.4122 1)
0.7660
Pure graphite
1.7379
Graphite plait
1.7709
St
1.7218
CW 713 R
WLSt
1.0460
5.8
5.3106
St
45H
ST
1.0904
1.5415
Stellite
1.7709
1.7218
1.7379
1.4122 1)
0.7660
Pure graphite
1.7379
Graphite plait
1.7709
St
1.7218
CW 713 R
WLSt
1.0460
5.8
5.3106
St
45H
ST
1.0904
1.7335
Stellite
1.7709
1.7218
1.7379
1.4122 1)
0.7660
Pure graphite
1.7379
Graphite plait
1.7709
St
1.7218
CW 713 R
WLSt
1.0460
5.8
5.3106
St
45H
ST
1.0904
1.7383
Stellite
1.7709
1.7218
1.7379
1.4122 1)2)

0.7660
Pure graphite 2)

1.7379
Graphite plait
1.7709
St
1.7218
CW 713 R

WLSt
1.0460
5.8
5.3106
St
45H
ST
1.0904
4 Spare parts

1) On request stem in 1.4923 with stellited seats
2) For temperatures > 570 C stem with stellited seats in 1.4923 and hightemperature-packing
Dimensions/mm
Weights/kg and Kvs-values

DIN/ISO
DN
L
H
Stroke R/Stroke
D
5210
10
15
20
25
32
40
50
65 / 50
150
150
160
160
250
250
250
250
208
208
250
250
415
415
415
415
10
10
16
16
27
27
27
27
5
5
8
8
9
9
9
9
140
140
180
180
280
280
280
280
F07/F10
F07/F10
F10
F10
F10/F14
F10/F14
F10/F14
F10/F14

Kvs
DN
BW
(m3/h)

10
4
2,3
15
4
3,4
20
6,9
6,2
25
6,9
7,9
32
23
20,0
40
23
24,1
50
23
28,3
65 / 50
23
28,3
Attention: In case of welding connections the permissible

operating overpressure is valid for the corresponding tube dimension.
6100.1.05.14
14
Globe valves
200 LM
Globe valves
Lift check valve HD 2000
PN 500
240 MT
n
n
PN 500
DN 10-65
DN 10-65
ASME
version
available
Material PN 20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 5802) 5902) 6002) 6102) 6202) 6302) 6402) 6502)

1.0460 500 550 550 550 550 550 550 518 463 389 315 300 285 270 255 240 213 177 146

1.5415 500 550 550 550 550 550 550 550 550 537 518 514 510 507 503 500 496 493 489 426 333 253 200 160

1.7335 500 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 500 426 338 275 222 173 142 116

1.7383 2) 500 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 500 437 381 333 289 252 214 189 163 140 124

1.4903 2) 500 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 500 465 430 380 338 298 261 231 198 172
1.4901 2)
500 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 526 470 419 370 322 278 241 207
1.4550
500 550 550 550 550 550 550 544 504 481 463 460 456 454 451 449 447 445 443 442 441 440 439 438 437 437 436 435 434 433 396 363 320 271 240 207
2) For temperatures > 570 C, stem in 1.4980 and hightemperature-packing.
15
6100.1.05.14
Globe valves
200 LM
Globe valves
PN 500
240 MT
n
n
PN 500
DN 10-65
DN 10-65
Standard features
Media
Disc and stem in one piece

n Non-turning, rising stem
n Position indicator / Anti-rotation device
n Throttle disc
n Yoke sleeve supported by needle bearings
n Greater than DN 20 with integral actuator flange
n Back seat type available (200 LS / 200 LJ)
n All HD 2000 valves also available in
angle pattern (e.g. 202 LM)
Depending on the material the valves are suitable

n
n
reformers and hydrocrackers, petrochemical and
chemical industries

Pressure rating up to 550 bar
(depending on selected material)
n
n
Materials
n
n
n
n
n
n
n
1.0460
1.4550
1.4901
1.4903
1.5415
1.7335
1.7383
Design Highlights
Body seat: tapered seat welded on integratedly
with stellite
Disc and stem in one piece; up from 570 C

with stellited tapered seat
Sealing to the outside only by means of the

gland packing
Body and bonnet in two separate pieces with bolted

connection
Benefits
No pressed in or screwed seat ring, therefore no
crevice corrosion or loosening
Damage between disc and stem duo to high flowrates

is prevented
No bonnet gasket, therefore reduction of possible

leakage areas

of the body seats
Yoke sleeve made of bronze
Cup springs above the upper needle bearing
Good emergency running properties
To maintain the necessary closing forces when

dimensions change between stem and yoke arms due
to thermal fluctuation
6100.1.05.14
16
Globe valves
200 LM
PN 500
DN 10-65
200 LM Shut-off globe valve

D
600
619
610
605
531
590
553
524
527
511
510
552
716
448
440
464
462
200
420 421
190
412
400
170
100
17
6100.1.05.14
Globe valves
202 LM
PN 500
DN 10-65
202 LM Shut-off globe valve

D
600
619
610
605
531
590
553
524
527
511
510
552
716
448
440
200
420 421
412
400
L1
100
L1
6100.1.05.14
18
Globe valves
Globe valves
Stop check valve
Globe valves
240 MM
n
PN 500
240 MT
200 LS
n
PN 500
DN 10-65
DN 10-65
PN 500
DN 10-65
240 MM Stop check valve
200 LS globe valve with back seat
also available in angle pattern

D
D
600
600
619
619
610
610
605
590
531
553
524
524
527
527
511
511
H
553
510
590
531
605
510
552
552
716
716
448
448
440
440
200
420 421
420 421
412
412
411
400
400
330
100
200
304
100
L
240 MT Lift check valve

192
172
210
160
308
330
100
304
19
6100.1.05.14
Globe valves
Globe valves
Stop check valve
Globe valves
240 MM
n
PN 500
240 MT
200 LM/LS
n
PN 500
DN 10-65
DN 10-65
PN 500
DN 10-65
Materials
Pos.
Component
1.0460 (21)
1.5415 (42)
1.7335 (44)
1.7383 (45) 2)
100 Body
1.0460
1.5415
1.7335
1.7383
welded on with
Stellite
Stellite
Stellite
Stellite
4 Gasket
Graphite
Graphite
Graphite
Graphite
160
170 Stud
1.7709
1.7709
1.7709
1.7709
172 Stud
1.4923
1.4923
1.4923
1.4923
190 Hexagonal nut
1.7218
1.7709
1.7218
1.4986
192 Hexagonal nut
1.4923
1.4923
1.4923
1.4923
200 Bonnet
1.7379
1.7379
1.7379
1.7379
210 Cover
1.7380
1.7380
1.7380
1.7380
4 Disc
1.4923
1.4923
1.4923
1.4923
304
308 Guide bush
1.4923
1.4923
1.4923
1.4923
330 Pressure spring
2.4669
2.4669
2.4669
2.4669
4 Stem
1.4122 1)
1.4122 1)
1.4122 1)
1.4122 1)2)
400
411 Back seat ring
1.4980
1.4980
1.4980
1.4980
412 Guide sleeve
0.7660
0.7660
0.7660
0.7660
4 Packing
Pure graphite
Pure graphite
Pure graphite
Pure graphite
420
4 Thrust ring
Pure graphite
Pure graphite
Pure graphite
Pure graphite
421
440 Gland flange
1.7379
1.7379
1.7379
1.7379
448
4 Dirt scraper
Graphite plait
Graphite plait
Graphite plait
Graphite plait
462 Stud
1.7709
1.7709
1.7709
1.7709
464 Hexagonal nut
1.7218
1.7218
1.7218
1.7218
4 Yoke sleeve
CW 713 R
CW 713 R
CW 713 R
CW 713 R
510
4 Bearing
WLSt
WLSt
WLSt
WLSt
511
524 Spring
1.8159
1.8159
1.8159
1.8159
527 Supporting ring
1.4021
1.4021
1.4021
1.4021
531 Screwing
1.0460
1.0460
1.0460
1.0460
4 O-Ring
Viton
Viton
Viton
Viton
552
4 O-Ring
Viton
Viton
Viton
Viton
553
590 Grease nipple
5.8
5.8
5.8
5.8
600 Handwheel
5.3106
5.3106
5.3106
5.3106
605 Key
1.0060
1.0060
1.0060
1.0060
610 Hexagonal nut
St
St
St
St
619 Lock washer
St
St
St
St
716 Tension pin
1.0904
1.0904
1.0904
1.0904

4 Spare parts

1.4901(66) 2)
1.4550
1.4903
Stellite
Graphite
1.4923
1.4986
1.4986
1.4923
1.7379
1.4903
1.4923
1.4980
2.4699
1.4122 1)2)
1.4980
0.7660
Pure graphite
Pure graphite
1.7379
Graphite plait
1.4923
1.4923
CW 713 R
WLSt
1.8159
1.4021
1.0460
Viton
Viton
5.8
5.3106
1.0060
St
St
1.0904
1.4901
Stellite
Graphite
1.4923
1.4986
1.4923
1.4986
1.7379
1.4901
1.4923
1.4980
2.4699
1.4122 1)2)
1.4980
0.7660
Pure graphite
Pure graphite
1.7379
Graphite plait
1.4980
1.4923
CW 713 R
WLSt
1.8159
1.4021
1.4122
Viton
Viton
5.8
5.3106
1.0060
St
St
1.0904
1.4550
Stellite
Graphite
1.4980
1.4986
1.4986
1.4986
1.7379 3)
1.4550
1.4980
1.4980
2.4669
1.4980 1)
1.4980
0.7660
Pure graphite
Pure graphite
1.7379 3)
Graphite plait
1.4980
1.4986
CW 713 R
WLSt
1.8159
1.4021
1.0460
Viton
Viton
5.8
5.3106
1.0060
St
St
1.0904
1) On request stem with stellited seats

2) For temperatures > 570 C stem with stellited seats in 1.4980 and hightemperature-packing.
3) Nickel plated
Dimensions/mm

DN
L
L1
H
H1 Stroke
10
15
20
25
32
40
50
65
1.4903 (63) 2)
150
150
180
180
300
300
300
360
75
75
90
90
150
150
150
200
228
228
280
280
445
445
445
563
99
99
122
122
182
182
182
208
10
10
16
16
27
27
27
36
Weights/kg
R/
Stroke
D
5
5
8
8
9
9
9
12
140
140
225
225
360
360
360
450
DIN/ISO
5210

BW
BW
BW
BW
DN 200 LM 202 LM 240 MM 200 LS
F07 1)
F07 1)
F10
F10
F10/F14
F10/F14
F10/F14
F14/F16
10
15
20
25
32
40
50
65
6,0
6,0
11,5
11,3
47,5
47,0
46,5
107,0
6,0
6,0
11,5
11,3
47,5
47,0
46,5
107,0
6,0
6,0
11,5
11,3
47,5
47,0
46,5
128,0
6,0
6,0
11,5
11,3
47,5
47,0
46,5
107,0
BW Kvs (m3/h)
240 MT 200 LM / LS
3,8
3,8
7,9
7,7
30,5
30,0
29,5
72,0
2,3
3,4
6,2
7,9
20,0
24,1
28,3
48,5
1) Specify flange ends when placing order

Attention: In case of welding connections the permissible
operating overpressure is valid for the corresponding tube dimension.
6100.1.05.14
20
Globe valves
High pressure globe valve DVA 25 / DVA 40
200 BZ
PD 25 / PD 40
DN 80-250
ASME
version
available
BW-
Version
Material
PD 20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650
1.0460
25 250 250 250 250 250 235 206 184 155 125 119 113 107 102 96 85 71 58
1.5415
25 300 300 300 300 300 280 258 221 213 206 205 203 202 200 199 197 196 194 170 132 101 80 64
1.7335
25 300 300 300 300 300 300 294 272 258 243 240 237 234 231 228 227 225 224 222 202 170 134 110 88 69 57 46
1.7380
25 300 300 300 300 300 300 300 294 272 258 255 252 249 246 243 240 237 234 224 199 174 152 132 115 100 85 75 65 56 49
1.6368
25 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 309 257 205 153 102
1.4903
25 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 316 290 263 238 213 191 169 150 132 115 100 85 75 65
1.4901
25 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 320 297 275 253 231 209 187 166 147 128 110 96 82

Attention: Pressure rating of the materials 1.6368, 1.4903 and 1.4901 was reduced in the cold range to 320 bar. This pressure rating is only valid for the DVA 25.
BW-
Version
Material
PD 20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650
1.0460
40 400 400 400 400 400 377 330 295 248 200 191 182 172 163 153 136 113 93
1.5415
40 480 480 480 480 480 448 413 354 342 330 328 325 323 321 318 316 314 311 272 212 161 127 102
1.7335
40 481 481 481 481 481 481 471 436 413 389 384 380 375 370 365 363 361 358 356 323 272 215 175 141 110 91 74
1.7380
40 480 480 480 480 480 480 480 471 436 413 408 403 398 394 389 384 380 375 358 318 278 243 212 184 160 137 120 104 90 79
1.6368
40 600 600 600 600 600 600 600 600 600 600 600 600 600 600 577 495 412 328 245 163
1.4903
40 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 596 551 506 464 422 382 342 306 271 240 212 184 160 137 120 104
1.4901
40 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 553 513 475 440 405 369 334 299 266 235 205 177 153 132


Attention: Pressure rating of the materials 1.6368, 1.4903 and 1.4901 was reduced in the cold range to 600 bar. This pressure rating is only valid for the DVA 40.
21
6100.1.05.14
Globe valves
Standard features
Straight pattern
n Pressure sealing bonnet acc. to VGB-guidelines
n Throttle disc
n Body seat welded on integratedly
n Outside screw and yoke
n Position indicator / Anti-rotation device
n Yoke sleeve supported at the top and the bottom
By means of needle bearings
n Universal valve head for mounting actuators
n
n

200 BZ
PD 25 / PD 40
DN 80-250
Materials
n
n
n
n
n
1.0460
1.5415
1.7335
1.7383
1.6368
1.4903
1.4901
Further materials and sizes on request.

Media
Chemical industries, industries and power plant.
Design Highlights
Benefits
Die-forged body and bonnet
Pressure sealing bonnet
Best possible sealing function
Body seat welded on integratedly with stellite
Extended bonnet
To reduce temperatures
Outside located anti twist device
Usable as position indicator
Minimum packing wear
Gland flange and gland ring in two separate pieces
Cup springs above the upper needle bearing
Damage to the stem by irregular tightening of gland

bolts is avoided
To minimize the expenditure of effort when operating
the valve
To maintain the necessary closing forces at elongation

changes between stem and yoke arms due to thermal
changes. Also to protect against excess torsion when
electric actuators are fitted.
6100.1.05.14
22
Globe valves
200 BZ
PD 25 / PD 40
DN 80-250
DVA 25 n PD 25 n DN 80-250
540
524
510
511
200
464
H
462
440
190
170
273
420
272
271
160
270
400
311
300
DS
100
L
DVA 40 n PD 40 n DN 80-200
540
524
510
511
200
464
440
H
462
190
170
420
273
272
271
160
270
400
311
300
DS
100
23
6100.1.05.14
Globe valves
200 BZ
PD 25 / PD 40
DN 80-250
Materials
Pos.
Component
1.0460 (21)
1.5415 (42)
1.7335 (44)
100 Body
1.0460
1.5415
1.7335
welded on with
Stellite
Stellite
Stellite
4 Gasket
Graphite
Graphite
Graphite
160
170 Stud
1.7709
1.7709
1.7709
190 Hexagonal nut
1.7218
1.7218
1.7218
200 Bonnet
1.7379
1.7379
1.7379
270 Cover
1.7383
1.7383
1.7383
271 Thrust ring
1.7383
1.7383
1.7383
272 Segmentring
1.7383
1.7383
1.7383
273 Cover
1.5419
1.5419
1.5419
300
4 Disc
1.4903
1.4903
1.4903
welded on with
Stellite
Stellite
Stellite
311 Grooved pin
1.4571
1.4571
1.4571
400
4 Stem
1.4122
1.4122
1.4122
400
4 Stem up to 500C
1.4980*
420
4 Packing
Graphite
Graphite
Graphite
440 Gland flange
1.7380
1.7380
1.7380
462 Stud
1.7709
1.7709
1.7709
464 Hexagonal nut
1.7218
1.7218
1.7218
510
4 Yoke sleeve
CW713R
CW713R
CW713R
511
4 Bearing
WLSt
WLSt
WLSt
524 Spring
Spring Steel
Spring Steel
Spring Steel
540 Flange
1.0460
1.0460
1.0460

4 Spare parts

* In PD 25 up to DN 150
* In PD 40 up to DN 125
DN
DS

L
mm
80
100
125
150
200
250
305 450 (475)

406
575
483 675 (725)
559 800 (850)
711 950 (1000)
864 1075 (1150)
H
mm
DN
DS

L
mm
80
100
125
150
200
368
575
359 675 (725)
533 800 (850)
610 950 (1000)
762 1075 (1150)
1.7383
1.6368
Stellite
Stellite
Graphite
Graphite
1.7709
1.4923
1.7218
1.7218
1.7379
1.7379
1.7383
1.4903
1.7383
1.4903
1.7383
1.4903
1.5419
1.5419
1.4903
1.4903
Stellite
Stellite
1.4571
1.4571
1.4122
1.4923
1.4980
Graphite
Graphite
1.7380
1.7380
1.7709
1.4923
1.7218
1.4923
CW713R
CW713R
WLSt
WLSt
Spring Steel
Spring Steel
1.0460
1.0460
1.4903 (63)
1.4901 (66)
1.4903
Stellite
Graphite
1.4923
1.7218
1.7379
1.4903
1.4903
1.4903
1.5419
1.4903
Stellite
1.4571
1.4923
1.4980
Graphite
1.7380
1.4923
1.4923
CW713R
WLSt
Spring Steel
1.0460
1.4901
Stellite
Graphite
1.4923
1.7218
1.7379
1.4901
1.4901
1.4901
1.5419
1.4901
Stellite
1.4571
1.4980
Graphite
1.7380
1.4923
1.4923
CW713R
WLSt
Spring Steel
1.0460
Weights/kg and Kvs-values DVA 25
Stroke R/Stroke H-Wheel DIN/ISO

mm
mm
mm
5210
32
42
51
62
82
96
11
450
14
500
17
600
21
720
27
24
F10 (F14)
F14
F14 (F16)
F16 (F25)
F25 (F30)
F30 (F35)
Dimensions/mm DVA 40
57
72
90
111
146
1.6368 (46)
Dimensions/mm DVA 25
64
82
100
122
160
190
1.7383 (45)
H
mm
Weights/kg and Kvs-values DVA 40
Stroke R/Stroke H-Wheel DIN/ISO

mm
mm
mm
5210
28
38
45
57
75
9
500
13
600
15
720
19
19

Kvs
DN
BW
(m3/h)

80
69
71
100
132
95
125
200
141
150
378
210
200
615
362
250
1120
510
F14
F14 (F16)
F16 (F25)
F25 (F30)
F30 (F35)

Kvs
DN
BW
(m3/h)

80
145
45
100
225
73
125
430
114
150
715
174
200
1140
300
6100.1.05.14
24
Globe valves
Further standards
Screw down non return valve 240 ME
Angle globe valve 202 AE
Changeover valve 203 EM
25
6100.1.05.14
Globe valves
Actuator variants
Universal Valve-Head
Assembly of E-actuators
For subsequent assembly of E-actuators

without welding
Standard design DN 65
Example
For running a particular limit of travel e.g.

with air or current
PERCON piston drive
PERCON piston drive
Spring opening
Spring closing
Example
6100.1.05.14
26
Globe valves
Variants
Disc with edge seat
Disc with soft seat
For media with small quantities

of impurities
E.g. of lead or PTFE for crystallizing media etc.
PTFE-stuffing box
Stuffing box with lantern and

test screw plug
Stuffing box with central cup

spring tightening
Also for sealing water or leakage suction
In order to minimize maintenance costs
Limit switches
On-Off position indicator
Non-rotating stem
Can be supplied mechanically

or inductively
With sheet metal bracket
In order to reduce packing wear
Stem extension
PERLOC system locking

mechanism Also for interlocking
Locking mechanism
With chambers for aggressive media

up to approx. max. 280 C
Disc with elastomer coated

obturator E.g. with PTFE spacer ring for
special media up to approx. 280 C
Control disc
Pinned down suitable for operating
in intermediate position
Hard faced back seat
With padlock
mechanism (safety circuits)
27
6100.1.05.14
Globe valves
Special valves
Y-pattern stop check valve
Globe valve
with insulating section
Bellow seal
Y-valve
Monobloc valve
Monobloc-Z-valve
6100.1.05.14
28
Gate valves
Small gate valve
808 GJ
PN 10-100
DN 10-40
Material PN -200 -60 -10 20 120 150 200 250 300 350 400 450 475 480 500 510 520 530 540 550
1.0460 10-40 40 40 40 37 35 32 28 24 21 13 8 7
63 63 63 63 56 50 45 40 36 32 21 13 12
100 100 100 100 90 80 70 60 56 50 34 21 19

1.7335 10-40 40 40 40 40 40 40 40 38 36 34 32 31 29 24 19 15 12 9
63 63 63 63 63 63 63 63 61 58 56 52 51 47 40 32 25 20 15
100 100 100 100 100 100 100 100 95 91 87 81 79 74 62 49 38 30 23

1.0566 2) 10-40 40 40 40 37 35 34 28
63 63 63 63 58 50 45 40
100 100 100 100 92 80 70 60

1.4571
10-40 40 40 40 40 40 38 35 33 31 30 29
63 63 63 63 63 63 57 50 47 44 42 40
100 100 100 100 100 100 90 80 75 70 65 60
29
6100.1.05.14
Gate valves
Small gate valve
808 GJ
PN 10-100
DN 10-40
Standard features
Media

Full bore
n Wedge
n Non-turning rising stem
n Available with flange, socket and
buttweld ends
Depending on the material the gate valves are suitable

n
n
other

n
n

Materials
n
n
n
n
1.0460
1.7335
1.0566
1.4571
Design Highlights
Benefits
Wedge made of stellite
Gasket, male and female face
Blow out protection
Full bore
No reduction in seat area
Minimal wear of the gland-packing
6100.1.05.14
30
Gate valves
Small gate valve
808 GJ
PN 10-100
DN 10-40
Small gate valve FL-version
D1
613
610
600
605
530
510
464
463
460
440
450
420
190
200
170
160
400
350
140
100
Socket welding version
31
6100.1.05.14
BW-version
Gate valves
Small gate valve
808 GJ
PN 10-100
DN 10-40
Materials
Pos.
Component
1.0460 (21)
1.7335 (44)
1.0566 (25)
100 Body
1.0460
1.7335
1.0566
1.4571
140 Seat ring
1.4571
1.4571 1)
4 Gasket
Graphite
Graphite
Graphite
160
170 Stud
1.7709
1.4923
A4-70
190 Hexagonal nut
1.7218
1.4923
A4-70
200 Bonnet
1.0460
1.7335
1.0566
350 Wedge
1.4021
2.5788
2.5788
4 Stem
1.4021
1.4021
1.4571
400
4 Packing
Graphite
Graphite
Graphite
420
440 Gland flange
1.0460
1.0460
1.4571
450 Rivet
1.1181
1.1181
A4-50
460 Gland bolt
1.1181
1.1181
1.4571
463 Washer
St
St
A4-50
464 Hexagonal nut
1.1181
1.1181
A4-70
4 Yoke sleeve
1.0718
1.0718
1.0718
510
530 Yoke nut
1.0718
1.0718
1.0718
600 Handwheel
0.7040
0.7040
0.7040
605 Key
1.0060
1.0060
1.0060
610 Hexagonal nut
St
St
St
613 Screw pin
45H
45H
45H

4 Spare parts

1.4571 (87)
1.4571
1.4571
Graphite
A4-70
A4-70
1.4571
2.5788
1.4571
Graphite
1.4571
A4-50
1.4571
A4-50
A4-70
1.0718
1.0718
0.7040
1.0060
St
45H
1) Welded on with Stellite
Dimensions/mm and Kvs-values

FL
BW
PN
DN
L
L

10-100
10

15
130
130

20
150
150

25
160
160

32
180
180

40
240
240
SM
Kvs
L
H
Stroke
D1 (m3/h)
105
105
105
105
115
115
205
205
205
205
228
228
27
27
27
27
35
35
140
140
140
140
180
180
14,2
29,2
39,5
74,7
95,3
6100.1.05.14
32
Gate valves
VALTRA Small gate valve
800/808 GJ
Class 800 (PN 10-40)
NPS 1/2 - 2 (DN 15-50)
Material PN -10 20 100 150 200 250 300 350 400 450 475 480
1.0460 10-40 40 40 40 37 35 32 28 24 21 13

Material -29 38 93,5 149 204,5 260 315,5 343,5 371 399 426,5 454,5
482 510 538

ASTM A 105 Class 800 136,2 136,2 124,1 120,7 116,6 110,0 100,7 98,6 97,9 92,7 75,9 49,3 31,7 19,0 9,7

33
6100.1.05.14
Gate valves
800/808 GJ
Class 800 (PN 10-40)
NPS 1/2 - 2 (DN 15-50)
Standard features
Media

Full bore
n Wedge
n Non-turning rising stem
n Available with flange, socket and
buttweld ends

n
n
other

n
n
Pressure rating up to 136,2 bar

Materials
n
n
1.0460
ASTM A 105
Design Highlights
Benefits
Wedge made of stellite
Gasket, male and female face
Blow out protection
Full bore
Minimal wear of the gland-packing
6100.1.05.14
34
Gate valves
800/808 GJ
Class 800 (PN 10-40)
NPS 1/2 - 2 (DN 15-50)
Small gate valve FL-version

D
610
609
440
600
430
464
420
462
190
400
170
200
160
100
510
350
140
P.O. No.:
PN40 FORM B1
SHEET:
DOCUMENT:
071948
008
6100.1.05.14
CLASS:
PN40
SIZE:
DN25
LW
14
WEIGHT
KG:
DRAW:
DKSR418032E001N
0
REV.
LWREV.
REV.
REV.
GATE VALVE OS#Y BB FB FL DIN

DN25 " C22.8/1.4021 NACE
9021290OP STOCK
ITEM No.:
35
DESCRIPTION:
6,4
Fogaroli
SIEKMANN ECONOSTO GMBH &
LVF-RAOUL
TAG No.:
Socket welding version
CHECKED:
27/03/2008
CUSTOMER:
DATE:
DATE:
DATE:
DATE:
BW-version
Gate valves
800/808 GJ
Class 800 (PN 10-40)
NPS 1/2 - 2 (DN 15-50)
Materials
Pos. Component
1.0460 (21)

FL
ASTM A 105
(B1)
BW / SM
100 Body
1.0460
ASTM A 105
140 Seat ring
ASTM A 276 type 410
ASTM A 276 type 410
4 Gasket
Spiral-Grafit
Spiral-Grafit
160
170 Stud
AISI 410
AISI 410
190 Hexagonal nut
ASTM A 194 2H
ASTM A 194 2H
200 Bonnet
1.0460
ASTM A 105
350 Wedge
ASTM A 182 F6
ASTM A 182 F6
4 Stem
ASTM A 276 type 410
ASTM A 276 type 410
400
4 Packing
Graphite
Graphite
420
430 Gland ring
ASTM A 276 type 410
ASTM A 276 type 410
440 Gland flange
ASTM A 105
ASTM A 105
462 Stud
AISI 410
AISI 410
464 Hexagonal nut
ASTM A 194 2H
ASTM A 194 2H
4 Yoke sleeve
ASTM A 582 type 416
ASTM A 582 type 416
510
600 Handwheel
St
St
609 Washer
St
St
610 Hexagonal nut
St
St

4 Spare parts
Dimensions/mm

808 GJ
NPS
L
H
D
LW

808 GJ
NPS
SM
1/2
3/4
1
1 1/4
1 1/2
2
14,0
19,0
24,0
30,0
37,0
48,0
1/2
3/4
1
1 1/4
1 1/2
2
90
110
127
127
127
150
152
182
214
247
270
333
90
110
110
130
130
180
2,2
3,5
5,0
6,5
8,5
17,0
800 GJ
NPS
L
H
D
LW
800 GJ
NPS
SM
1/2
3/4
1
1 1/4
1 1/2
2
1/2
3/4
1
1 1/4
1 1/2
2
80
90
110
127
127
127
145
152
182
214
247
270
70
90
110
110
130
130
10,0
14,0
19,0
24,0
30,0
37,0
1,6
2,2
3,5
5,0
6,5
8,5
808 GJ PN 10-40
DN
L
H
D
a
808 GJ
DN
FL
15
20
25
40
50
15
20
25
40
50
130
150
160
240
250
152
182
214
270
333
90
110
110
130
180
14,0
18,0
24,0
36,5
48,0
4,5
6,5
7,9
13,0
24,5
Kvs
(m3/h)
14,2
25,2
37,2
61,0
95,3
149,0
7,2
14,3
26,3
40,9
63,9
100,0
14,2
25,2
37,2
95,3
149,0
6100.1.05.14
36
Gate valves
Gate valve
700 HJ/JJ (GA n PN 10-40)
PN 10-100
DN 50-150
ASME
version
available
Pressure rate table acc. DIN 2401

Material PN -60 -10 20 120 150 200 250 300 350 400 425 450 475 500 510 520 530 540 550

1.0619
16 16,0 16,0 16,0 15,0 14,0 13,0 11,0 10,0 8,0

25 25,0 25,0 25,0 23,0 22,0 20,0 17,0 16,0 13,0

40 40,0 40,0 40,0 37,0 35,0 32,0 28,0 24,0 21,0
1.0460 10 2) 10,0 10,0 10,0 9,6 8,8 8,1 6,9 6,3 5,0

16 16,0 16,0 16,0 15,3 14,0 13,0 11,0 10,0 8,0

25 25,0 25,0 25,0 23,9 22,0 20,0 17,0 16,0 13,0

40 40,0 40,0 40,0 38,1 35,0 32,0 28,0 24,0 21,0

63 63,0 63,0 63,0 58,1 50,0 45,0 40,0 36,0 32,0

100 100,0 100,0 100,0 92,5 80,0 70,0 60,0 56,0 50,0
1.0566 3)4) 10 2) 10,0 10,0 10,0 10,0 10,0 9,0 8,0 7,0
16 2) 16,0 16,0 16,0 16,0 15,0 14,0 13,0 11,0
25 2) 25,0 25,0 25,0 25,0 24,0 22,0 20,0 17,0
40 2) 40,0 40,0 40,0 40,0 39,0 35,0 31,0 28,0
63 2) 63,0 63,0 63,0 63,0 61,0 55,0 49,0 44,0
100 2) 100,0 100,0 100,0 100,0 96,0 88,0 79,0 70,0
1.5415 10 2) 10,0 10,0 10,0 10,0 10,0 10,0 8,8 8,0 7,6 7,2 6,8
16 2) 16,0 16,0 16,0 16,0 16,0 16,0 14,1 12,8 12,2 11,5 10,9

25 25,0 25,0 25,0 25,0 25,0 25,0 22,0 20,0 19,0 18,0 17,0

40 40,0 40,0 40,0 40,0 40,0 40,0 35,0 31,0 30,0 29,0 28,0

63 63,0 63,0 63,0 63,0 63,0 63,0 56,0 50,0 47,0 46,0 45,0

100 100,0 100,0 100,0 100,0 100,0 100,0 87,0 78,0 74,0 72,0 70,0
1.7335 10 2) 10,0 10,0 10,0 10,0 10,0 10,0 10,0 9,6 9,2 8,8 8,4 8,0 7,2 6,0 4,8 3,6
16 2) 16,0 16,0 16,0 16,0 16,0 16,0 16,0 15,4 14,7 14,1 13,4 12,8 11,5 9,6 7,7 5,8

25 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,0 23,0 22,0 21,0 20,0 18,0 15,0 12,0 9,0

40 40,0 40,0 40,0 40,0 40,0 40,0 40,0 38,0 36,0 35,0 34,0 33,0 29,0 24,0 19,0 15,0

63 63,0 63,0 63,0 63,0 63,0 63,0 63,0 61,0 58,0 57,0 56,0 53,0 47,0 40,0 32,0 25,0

100 100,0 100,0 100,0 100,0 100,0 100,0 100,0 95,0 91,0 89,0 87,0 82,0 74,0 62,0 49,0 38,0
1.7383 10 2) 10,0 10,0 10,0 10,0 10,0 10,0 10,0 9,5 9,1 8,9 8,7 8,3 7,4 6,3 5,0 4,4 3,8 3,3
16 2) 16,0 16,0 16,0 16,0 16,0 16,0 16,0 15,2 14,6 14,2 13,9 13,2 11,8 10,0 7,9 7,0 6,0 5,2
25 2) 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,8 22,8 22,3 21,8 20,6 18,4 15,6 12,4 10,9 9,4 8,1
40 2) 40,0 40,0 40,0 40,0 40,0 40,0 40,0 38,0 36,4 35,6 34,8 33,0 29,5 25,0 19,8 17,4 15,1 13,0
63 2) 63,0 63,0 63,0 63,0 63,0 63,0 63,0 60,8 58,2 57,0 55,7 52,8 47,2 40,0 31,7 27,8 24,2 20,8
100 2) 100,0 100,0 100,0 100,0 100,0 100,0 100,0 95,0 91,0 89,0 87,0 82,5 73,8 62,5 49,5 43,5 37,8 32,5
2) Pressure rating not applicable in design code
3) In case of stainless steel bolts (DINmaterial code A4-70) with > 8 x d bolt length the strength characteristics acc. to table 6 of DIN 267 part 11 have been considered.
4) At temperature > 50 C only applicable for short time service.
37
6100.1.05.14
Gate valves
Gate valve
700 HJ/JJ (GA n PN 10-40)
PN 10-100
DN 50-150
Pressure rate table acc. DIN EN 1092-1

Material PN -10 20 50 100 150 200 250 300 350 400 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600

1.0619
16 16,0 16,0 16,0 14,8 14,0 13,3 12,1 11,0 10,2 9,5 5,2

25 25,0 25,0 25,0 23,2 22,0 20,8 19,0 17,2 16,0 14,8 8,2

40 40,0 40,0 40,0 37,1 35,2 33,3 30,4 27,6 25,7 23,8 13,1

1.0460
10 10,0 10,0 10,0 9,2 8,8 8,3 7,6 6,9 6,4 5,9 3,2

16 16,0 16,0 16,0 14,8 14,0 13,3 12,1 11,0 10,2 9,5 5,2

25 25,0 25,0 25,0 23,2 22,0 20,8 19,0 17,2 16,0 14,8 8,2

40 40,0 40,0 40,0 37,1 35,2 33,3 30,4 27,6 25,7 23,8 13,1

63 63,0 63,0 63,0 58,5 55,5 52,5 48,0 43,5 40,5 37,5 20,7

100 100,0 100,0 100,0 92,8 88,0 83,3 76,1 69,0 64,2 59,5 32,8

1.5415
10 10,0 10,0 10,0 10,0 10,0 10,0 9,7 8,5 8,0 7,4 6,9 6,4 5,9 5,4 4,9 4,4 3,5 2,8 2,2

16 16,0 16,0 16,0 16,0 16,0 16,0 15,6 13,7 12,9 11,9 11,0 10,2 9,4 8,6 7,8 7,0 5,6 4,4 3,5

25 25,0 25,0 25,0 25,0 25,0 25,0 24,4 21,4 20,2 18,6 17,2 16,0 14,7 13,5 12,3 11,0 8,8 7,0 5,5

40 40,0 40,0 40,0 40,0 40,0 40,0 39,0 34,2 32,3 29,9 27,6 25,6 23,6 21,6 19,7 17,7 14,0 11,2 8,9

63 63,0 63,0 63,0 63,0 63,0 63,0 61,5 54,0 51,0 47,1 43,5 40,3 37,2 34,1 31,0 27,9 22,2 17,7 14,1

100 100,0 100,0 100,0 100,0 100,0 100,0 97,6 85,7 80,9 74,7 69,0 64,0 59,1 54,2 49,2 44,2 35,2 28,0 22,3

1.7335
10 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 9,5 9,0 8,4 8,0 7,6 7,2 6,8 6,5 5,5 4,4 3,7 2,9 2,3 1,9 1,5

16 16,0 16,0 16,0 16,0 16,0 16,0 16,0 16,0 15,2 14,4 13,4 12,8 12,1 11,5 10,8 10,4 8,8 7,1 5,9 4,6 3,7 3,0 2,5

25 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,8 22,5 21,0 20,0 19,0 18,0 17,0 16,3 13,8 11,1 9,3 7,2 5,8 4,7 3,9

40 40,0 40,0 40,0 40,0 40,0 40,0 40,0 40,0 38,0 36,0 33,7 32,0 30,4 28,8 27,2 26,0 22,0 17,9 14,8 11,6 9,3 7,6 6,2

63 63,0 63,0 63,0 63,0 63,0 63,0 63,0 63,0 60,0 56,7 53,1 50,5 47,9 45,4 42,8 41,1 34,8 28,2 23,4 18,3 14,7 12,0 9,9

100 100,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0 95,2 90,0 84,2 80,2 76,1 72,0 68,0 65,2 55,2 44,7 37,1 29,0 23,3 19,0 15,7

1.7383
10 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 9,7 9,2 8,8 8,3 7,8 7,3 6,9 6,4 5,6 4,9 4,2 3,7 3,2 2,7 2,4 2,0 1,8 1,6

16 16,0 16,0 16,0 16,0 16,0 16,0 16,0 16,0 15,6 14,8 14,0 13,3 12,5 11,8 11,0 10,2 8,9 7,8 6,8 5,9 5,1 4,4 3,8 3,3 2,8 2,5

25 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,4 23,2 22,0 20,8 19,6 18,4 17,2 16,0 14,0 12,2 10,7 9,2 8,0 6,9 6,0 5,2 4,5 4,0

40 40,0 40,0 40,0 40,0 40,0 40,0 40,0 40,0 39,0 37,1 35,2 33,3 31,4 29,5 27,6 25,7 22,4 19,6 17,1 14,8 12,9 11,0 9,7 8,3 7,2 6,4

63 63,0 63,0 63,0 63,0 63,0 63,0 63,0 63,0 61,5 58,5 55,5 52,5 49,5 46,5 43,5 40,5 35,4 30,9 27,0 23,4 20,4 17,4 15,3 13,2 11,4 10,2

100 100,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0 97,6 92,8 88,0 83,3 78,5 73,8 69,0 64,2 56,1 49,0 42,8 37,1 32,3 27,6 24,2 20,9 18,0 16,1
6100.1.05.14
38
Gate valves
Gate valve
700 HJ/JJ (GA n PN 10-40)
PN 10-100
DN 50-150
Pressure rate table only valid for buttweld ends

Material PD -60 -10 20 100 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600

1.0460
10 100,0 100,0 100,0 100,0 94,0 82,0 74,0 64,2 59,5 48,0 45,0 43,0 41,0 38,0 34,0 28,0 23,0

10 100,0 102,1 102,1 100,0 96,0 88,0 79,0 70,0
1.0566 2)3)

1.5415
10 120,0 120,0 120,0 120,0 112,0 103,0 88,0 85,0 82,0 82,0 81,0 81,0 80,0 79,0 79,0 78,0 78,0 68,0 53,0 40,0 32,0 25,0

1.7335
10 120,0 120,0 120,0 120,0 120,0 118,0 109,0 103,0 97,0 96,0 95,0 94,0 92,0 91,0 91,0 90,0 89,0 89,0 81,0 68,0 54,0 44,0 35,0 28,0 23,0 18,0

1.7383
10 120,0 120,0 120,0 120,0 120,0 120,0 118,0 109,0 103,0 102,0 101,0 99,0 98,0 97,0 96,0 95,0 94,0 89,0 79,0 69,0 61,0 53,0 46,0 40,0 34,0 30,0 26,0 22,0 20,0

2) At temperatures > 50 C only applicable for short time service.
3) In case of stainless steel bolts (DINmaterial code A4-70) with > 8 x d bolt length the strength characteristics acc. to table 6 of DIN 267 part 11 have been considered.
39
6100.1.05.14
Gate valves
Gate valve
700 HJ/JJ (GA n PN 10-40)
Standard features
n
n
n
n
n
n
n
n
Split disc gate valve / 2 disc-design = Type JJ

Wedge gate valve / Flexible wedge design = Type HJ
Full bore, exception DN 65/50 and DN 125/100
Non turning, rising stem
Yoke sleeve
Available with flange and buttweld ends
Option standard features GA

n
n
n
Wedge gate valve / Flexible wedge design

Inside screw
Non-rising turning stem
PN 10-100
DN 50-150
Materials
n
n
n
n
n
n
1.0460
1.0619 just for flange type PN 10-40
1.0566
1.5415
1.7335
1.7383
Media
n
n
n

Acc. to PERSTA PD 10 up to 120 bar
Design Highlights
The main valve body is one-piece die-forged
incorporating the bonnet flange and the guide for the
shut-off device
Hard faced seats (valve body and shut-off device).

Hardness app. 35-37 HRC

other
Benefits
Die-forged parts, compared with cast steel parts are
generally free from porosity and shrink holes. The
special of the valve body minimizes the existance of
welding seams
To improve the stress capability when temperature and

pressure fluctuate

n No reduction in seat area
Bolted bonnet with reduced shaft bolts
Full bore, except DN 65/50 and DN 125/100
Non - turning rising stem
Type GA, turning non-rising stem
Minimum wear to the gland packing compared with

ground stem surfaces
Small dimensions
6100.1.05.14
40
Gate valves
Gate valve
700 HJ/JJ (GA n PN 10-40)
PN 10-100
DN 50-150
610
613
600
605
510
531
511
590
464
462
440
H
420
450
200
170
190
160
400
360
363
100
H1
700 GA
41
6100.1.05.14
Gate valves
Gate valve
700 HJ/JJ (GA n PN 10-40)
PN 10-100
DN 50-150
Materials
Pos. Component

1.0619 (11)
PN 10-40
1.0460 (21)
1.0566 (25)
1.5415 (42)
1.7335 (44)
1.0460 1)
1.0566 1)
1.5415 2)
1.7335 2)
100 Body
1.0619 1)
160
4 Gasket
Graphite 4)
Graphite 4)
Graphite 4)
Graphite 4)
Graphite 4)
170 Stud
1.7709
1.7709
A4-70
1.7709
1.7709
190 Hexagonal nut
1.7218
1.7218
A4-70
1.7218
1.7218
200 Bonnet
1.0460
1.0460
1.0566
1.5415
1.7335
3)
3)
3)
2)
4 Disc
1.0460
1.0460
1.0566
1.5415
1.7335 2)
360
363 Pressure piece
1.4021
1.4021
1.4021
1.4021
1.4021
4 Stem
1.4021
1.4021
1.4571
1.4122
1.4122
400
4 Packing
Graphite
Graphite
Graphite
Graphite
Graphite
420
440 Gland flange
1.0460
1.0460
1.4571
1.0460
1.0460
450 Grooved pin
St
St
1.4571
St
St
462 Eye bolt
1.1181
1.1181
A4-50
1.1181
1.1181
464 Hexagonal nut
1.1181
1.1181
A4-70
1.1181
1.1181
4 Yoke sleeve
1.0718
1.0718
1.0718
1.0718
1.0718
510
4 Bearing
WLSt
WLSt
WLSt
WLSt
WLSt
511
531 Screwing
1.0718
1.0718
1.0718
1.0718
1.0718
590 Grease nipple
5.8
5.8
5.8
5.8
5.8
600 Handwheel
5.3106
5.3106
5.3106
5.3106
5.3106
605 Key
1.0060
1.0060
1.0060
1.0060
1.0060
610 Hexagonal nut
St
St
St
St
St
613 Screw pin
45H
45H
45H
45H
45H

4 Spare parts

1) Welded on with Cr17


3) Welded on with 18/8

4) DN 150 grooved with graphite layer

1.7383 (45)
1.7383 2)
Graphite 4)
1.7709
1.7218
1.7383
1.7383 2)
1.4021
1.4122
Graphite
1.0460
St
1.1181
1.1181
1.0718
WLSt
1.0718
5.8
5.3106
1.0060
St
45H
Attention: Ki-Gate-Valve 700 GA only in material 1.0460
Dimensions/mm
700 GA GS-C25N 700 GA

PN 10-25 40-100 10-40 63-100 10-40 63-100 10-25
40 10-25
40
63
100 10-40 63-100 10-25
40 10-40
Kvs
DN
L
L
H
H Stroke
D
D
H1
FL
FL
FL
FL
FL
FL
BW
BW
FL
FL
BW (m3/h)

50
250
250
337
337
63
180
180
280
21,5
21,5
19,0
19,0
23,5
26,5
15,0
15,5
19,0
19,0
15,0 258,0
65 / 50
270
290
337
337
63
180
180
280
21,0
21,0
26,0
30,5
15,5
16,0
21,0
21,0
28,0 258,0
80
280
310
410
410
90
225
225
345
40,0
40,0
35,0
35,0
40,5
45,0
28,0
31,0
35,0
35,0
28,0 628,0
100
300
350
455
505
110
280
360
405
57,0
61,5
50,0
54,0
63,0
71,0
43,0
47,0
50,0
54,0
43,0 991,0
125 / 100
325
400
455
505
110
280
360
405
53,5
59,0
74,0
89,0
45,0
49,0
53,0
59,0
45,0 991,0
150
350
450
655
685
165
360
450
525 114,0 120,0
92,0
98,0 138,0 155,0
80,0 100,0
92,0
98,0
80,0 2323,0
6100.1.05.14
42
Gate valves
Gate valve
700 HJ/JJ (GA)
PN 10-40
DN 200-250
Material PN -60 -10 20 120 150 200 250 300 350 400 450

10-16 16 16 16 15 14 13 11 10 8 6
1.0460 25 25 25 25 23,5 22 20 17 16 13 10
40 40 40 40 37,5 35 32 28 24 21 10

10-16 16 16 16 16 15 14 13 11
1.0566 2) 25 25 25 25 25 24 22 20 17
40 40 40 40 40 38 35 32 28

2) At temperatures > 50 C only applicable for short-time service.
43
6100.1.05.14
Gate valves
Gate valve
700 HJ/JJ (GA)
PN 10-40
Standard features
n
n
n
n
n
n
n
n
Split disc gate valve / 2 disc-design = Type JJ

Wedge gate valve / Flexible wedge design = Type HJ
Body with full bore
Non-turning rising stem
Yoke sleeve
DN 200-250
Materials
n
n
1.0460
1.0566
Media
For water, gas, oil and other non aggressive media
Option standard features GA

n
n
n
Wedge gate valve / Flexible wedge design

Inside screw
Non-rising turning stem
other

n
n

Design Highlights
n
Hard faced seats (valve body and shut-off device)

Hardness app. 35-37 HRC
Benefits
n
To improve the stress capability when temperature and

pressure fluctuate

n No reduction at seat area
Bolted bonnet with reduced shaft bolts
Full bore
Type GA, rotating non-rising stem
Minimum wear to the gland packing compared

with ground stem surfaces
Small dimensions
Simple retrofitting of an actuator possible without

welding
6100.1.05.14
44
Gate valves
Gate valve
700 HJ/JJ (GA)
PN 10-40
DN 200-250
610
613
600
605
531
532
510
511
590
464
462
440
450
420
200
170
160
190
400
362
360
361
100
700 JJ
45
6100.1.05.14
350
700 HJ
Gate valves
Gate valve
700 HJ/JJ (GA)
PN 10-40
DN 200-250
Materials
Pos.
Component
1.0460 (21)
100 Body
1.0460 3)
160
4 Seat ring
Grooved with

graphite layer
170 Stud
1.1181
190 Hexagonal nut
1.1181
200 Bonnet
1.0460
4 Wedge
1.0460 4)
350
360 / 361 4
Disc
1.8507 4)
362
4 Ball
WLSt
4 Stem
1.4021 5)
400
4 Packing
Graphite
420
Gland flange
1.0460
440
450 Pin
St
462 Eye bolt
1.1181
464 Hexagonal nut
1.1181
510 Yoke sleeve
1.0718
4 Needle bearing
WLSt
511
4 Screwing
1.0718
531
532 Screw pin
45H
4 Grease nipple
5.8
590
600 Handwheel
5.3106
605 Key
1.0060
610 Hexagonal pipe nut
St
613 Screw pin
45H

4 Spare parts

1.0566 (25)
1.0566 3)
Grooved with
graphite layer
A4-70
A4-70
1.0566
1.0566 4)
1.0566 4)
WLSt
1.4571
Graphite
1.4571
1.4571
A4-50
A4-70
1.0718
WLSt
1.0718
45H
5.8
5.3106
1.0060
St
45H
3) Welded on with 18/8

4) Welded on with Cr17
5) PN 40 DN 250 = 1.4122
Attention: Ki-Gate-Valve 700 GA only in material 1.0460
Dimensions/mm

PN
PN
PN
PN

10-25
40 Stroke 10-25
40
DN
L
L
H
h
D
D

200
400
550
810
220
360
450
250
450
650
975
285
450
450

700 GA
DN
H1
700 GA
DN
200
250
200
250
590
725

FL
DN PN 10-25
200
250
151,5
285,0
138,5
263,0
FL
PN 40
BW
PN 10-25
BW
PN 40
Kvs
(m3/h)
185
325
140
245
140
280
4000
6247
170
303
125
223
125
258
4000
6247
6100.1.05.14
46
Gate valves
Gate valve
700 HJ/JJ
PN 63-100
DN 200-300
Material PN -60 -10 20 120 150 200 250 300 350 400 450 475 480 500 510 520 530 540 550 560 570 580 590 600

1.0460 63 63 63 63 58 50 45 40 36 32 21 14 12
100 100 100 100 91 80 70 60 56 50 34 21 19

1.5415 63 63 63 63 63 63 63 56 50 47 45 37 35 29 22 16 14
100 100 100 100 100 100 100 87 78 74 70 57 54 45 34 27 22

1.7335 63 63 63 63 63 63 63 63 61 58 56 53 51 47 40 32 25 20 16 13 10
100 100 100 100 100 100 100 100 95 91 87 82 80 74 62 49 38 31 24 19 16

1.7383 63 63 63 63 63 63 63 63 62 62 60 55 53 47 40 35 28 25 22 18 15 12 11 9
100 100 100 100 100 100 100 100 98 96 94 85 82 74 62 53 43 39 33 27 23 19 17 15

47
6100.1.05.14
Gate valves
Gate valve
700 HJ/JJ
PN 63-100
Standard features
n
n
n
n
n
n
n
n
Split disc gate valve / 2 disc design type = Type JJ

Wedge gate valve / flexible wedge-design Type HJ
Full bore
Yoke sleeve
DN 200-300
Media
other

n
n

Materials
n
n
n
n
1.0460
1.5415
1.7335
1.7383
For low temperature service available as casting.

Other materials on request.
Design Highlights
Benefits
Hard faced seats (valve body and shut-off device)
Gasket located in gap
Blow out protection
Full bore
Non-rising stem
Minimum wear to the gland packing compared

with ground stem surfaces
6100.1.05.14
48
Gate valves
Gate valve
700 HJ/JJ
PN 63-100
DN 200-300
D
613
h
610
600
605
531
590
510
511
464
440
462
450
420
190
200
170
160
400
360
361
363
100
700 JJ
49
6100.1.05.14
700 HJ
Gate valves
Gate valve
700 HJ/JJ
PN 63-100
DN 200-300
Materials
Pos. Component
1.0460 (21)
1.5415 (42)
1.7335 (44)
1.7383 (45)

100 Body
1.0460
1.7383/1.5415
1.7383/1.7335
1.7383
4 Seat ring
Grooved with
Grooved with
Grooved with
Grooved with
160

graphite layer
graphite layer
graphite layer
graphite layer
170 Stud
1.7709
1.7709
1.7709
1.7709
190 Hexagonal nut
1.7218
1.7218
1.7218
1.7218
200 Bonnet
1.7383
1.7383
1.7383
1.7383
Disc
1.7383 4)
1.7383
1.7383 1)3)
1.8507 3)
360 / 361 4
363
4 Pressure piece
1.4122
1.4122
1.4122
1.4122
4 Stem
1.4021
1.4122
1.4122
1.4122
400
4 Packing
Graphite
Graphite
Graphite
Graphite
420
440 Gland flange
1.0460
1.0460
1.0460
1.0460
6)
6)
6)
St
St
St 6)
450 Pin
St
462 Eye bolt
1.1181 5)
1.1181 5)
1.1181 5)
1.1181 5)
464 Hexagonal nut
1.1181 9)
1.1181 9)
1.1181 9)
1.1181 9)
510
4 Yoke sleeve
1.0718 8)
1.0718 8)
1.0718 8)
1.0718 8)
511
4 Roller bearing
WLSt 7)
WLSt 7)
WLSt 7)
WLSt 7)
531 Screwing
1.0718
1.0718
1.0718
1.0718
590 Grease nipple
5.8
5.8
5.8
5.8
600 Handwheel
St
St
St
St
605 Key
1.0060
1.0060
1.0060
1.0060
610 Hexagonal nut
St
St
St
St
613 Screw pin
45H
45H
45H
45H

4 Spare parts
1)
2)
3)
4)
5)
6)
7)
8)
9)
DN 250 = 1.7383 welded on with Stellite

Welded on with Cr17
Welded on with Stellite
DN 250 = 1.0460 welded on with Cr17
DN 250 = 1.7709
DN 250 = 1.7218
DN 250 = Roller bearing
DN 250 = CW 713 R

DN 250 = 1.7218
Dimensions/mm

PN

63-100 Stroke
DN
L
H
h
D

200
550
890
210
600
250
650
1110
265
720
300
750
1310
313
900


DN
FL
PN
63
200
270
250
480
300
690

FL
PN
100
285
538
750
BW
PN
63-100
215
430
560
Kvs
(m3/h)
4000
6247
8997
6100.1.05.14
50
Gate valves
Gate valve
400 JJ
PN 63-100
DN 350-700
Material PN -10 20 120 150 200 250 300 350 400 450 475 480 500 510 520 530 540 550 560 570 580 590 600

1.0425 63 63 63 63 58 50 45 40 36 32 21 14,0 12
100 100 100 100 91 80 70 60 56 50 34 21,8 19

1.5415 63 63 63 63 63 63 63 56 50 47 45 37,0 35 29 22 16 14
100 100 100 100 100 100 100 87 78 74 70 57,0 54 45 34 27 22

1.7335 63 63 63 63 63 63 63 63 61 58 56 53,0 51 47 40 32 25 20 16 13 10
100 100 100 100 100 100 100 100 95 91 87 82,0 80 74 62 49 38 31 24 19 16

1.7383 63 63 63 63 63 63 63 63 62 62 60 55,0 53 47 40 35 28 25 22 18 15 12 11 9
100 100 100 100 100 100 100 100 98 96 94 85,0 82 74 62 53 43 39 33 27 23 19 17 15

51
6100.1.05.14
Gate valves
Gate valve
400 JJ
PN 63-100
Standard features
n
n
n
Split disc gate valve

Possibility to add an actuator
DN 350-700
Media


n
n


other
Materials
n
n
n
n
1.0425
1.5415
1.7335
1.7383
Design Highlights
Benefits
Seats and faced with stellite
Best possible sliding performance, minimum wear
Minimum wear to the gland packing
Yoke sleeve supported by needle bearing
Damage to the stem by irregular tightening of

gland bolts is avoided
Minimize the expenditure of effort
when operating valve
6100.1.05.14
52
Gate valves
Gate valve
400 JJ
PN 63-100
DN 350-700
531
511
510
Drawing
rotated
by 90
464
440
H
462
430
420
190
170
200
160
411
400
360
361
DS
363
100
53
6100.1.05.14
Gate valves
Gate valve
400 JJ
PN 63-100
DN 350-700
Materials
Pos.
Component
100 Body
welded on with
4 Seat ring
160
170 Stud
190 Hexagonal nut
200 Bonnet
Disc
360 / 361 4
welded on with
4 Pressure piece
363
4 Stem
400
4 Guide bushing
411
4 Packing
420
430 Gland ring
440 Gland flange
462 Stud
464 Hexagonal nut
4 Yoke sleeve
510
4 Bearing
511
531 Screwing
1.0425 (22)
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.0425
Stellite
Graphite
1.7709
1.7218
1.0460
1.7383
Stellite
1.4122
1.4021
1.8507
Graphite
1.5415
1.5415
1.7709
1.7218
CW 713 R
WLSt
1.7335
1.5415
Stellite
Graphite
1.7709
1.7218
1.5415
1.7383
Stellite
1.4122
1.4122
1.8507
Graphite
1.5415
1.5415
1.7709
1.7218
CW 713 R
WLSt
1.7335
1.7335
Stellite
Graphite
1.7709
1.7218
1.7335
1.7383
Stellite
1.4122
1.4122
1.8507
Graphite
1.5415
1.7383
1.7709
1.7218
CW 713 R
WLSt
1.7335
1.7383
Stellite
Graphite
1.7709
1.7218
1.7383
1.7383
Stellite
1.4122
1.4122
1.8507
Graphite
1.5415
1.7383
1.7709
1.7218
CW 713 R
WLSt
1.7335
4 Spare parts
Dimensions/mm

DN
DS

350
330
400
375
450
419
500
464
600
559
700
640
Stroke
L
H

365
850
1620
417
950
1745
455
1050
2030
515
1150
2260
625
1350
2560
690
1550
2695

DN
BW
350
400
450
500
600
700

950
1500
1850
2350
4300
5100
Kvs
(m3/h)
11243
14521
18105
22353
32188
41773
6100.1.05.14
54
Gate valves
VALTRA Gate valve
700 JJ
PN 10-25
DN 300-1000
610
H1
610
614
600
605
560,561
531
510
590
511
464
463
445
460
451
420
412
201
190
180
160
PN
614
600
605
16
532
510
kg
26
305
H1
D1 D
1160
330
450
350
550
1260
355
500
505 460
16x22
430
26
410
400
600
1430
410
600
565 515
16x26
482
26
560
500
700
1700
520
800
670 620
20x26
585
28
960
600
800
2035
630
800
780 725
20x30
685
28
1350
700
900
2260
735
895 840
24x30
800
30
1960
800
1000 2685
845
800 1015 950
24x33
905
32
2960
DN
H1
D1 D
d2
d4
kg
300
500
1160
330
450
460 410
12x26
378
28
305
350
550
1260
355
500
520 470
16x26
438
30
410
400
600
1430
410
600
580 525
16x30
490
32
560
500
700
1700
520
800
715 650
20x33
610
34
960
600
800
2035
630
800
840 770
20x36
725
36
1350
700
900
2260
735
800
910 840
24x36
795
36
1960
800
1000 2685
845
800 1025 950
24x39
900
38
2960
445 400
25
PN
40
1) Bei TB> 350C Werkstoff : 1.7709

PN 10-25
464
614
Sicherungsring
610
Sechskantmutter
hexagonal nut
440
605
Paeder
key
462
600
Handrad
handwheel
561
Senkschraube
countersunk screw
560
Verdrehsicherung
protect.against to
420
590
Schmiernippel
grease nipple
411
531
Verschraubung
screwing
511
Nadellager
needle bearing
510
Gewindebuchse
yoke sleeve
464
Sechskantmutter
hexagonal nut
463
Scheibe
washer
460
Klappschraube
gland bolt
451
Kerbstift
pin
445
Stopfbuchsbrille
gland flange
420
Packung
packing
411
Fhrungshlse
guide sleeve
400
Spindel
stem
DN 600,700
463
450
200
PN 40
190
DN 300,350,500
170
160
400
365
363
Baureihe: 700 JJ 22.1

fig.-no.:
362
360
Ersatzteil
100
spare part
piece detache
365
Plattenhalter
double disc guide
Druckstck
pressure piece
362
Kugel
ball
360
Schieberplatte
double disc
aufgepanzert mit
welded on with
201
Bgelhaube
bonnet
190 2)
Sechskantmutter
hexagonal nut
180 1) Schraubenbolzen
160
Dichtring
100
Gehuse
aufgepanzert mit
Datum
19.07.01
nderungen vorbehalten
Name
alternation reserved
L
GF/LR
sous reserve de modification
retaining ring
363
Pos.
Benennung
stud
gasket
body
welded on with
Designation
Platten-Rundsch
DN 300-800
gate valve
vanne passage dir
VALTRA ARMATUREN HANDELSGES.MBH-POSTFACH 2249-5956
Material PN -10 20 100 120 200 250 300 350 400

P265GH 10 10 10 10 10 9 8 7 6 5
16 16 16 16 16 14 13 11 10 8
25 25 25 25 25 22 20 17 16 13
55
PN
511
362
360
100
370
500
590
400
365
363
d4
12x22
300
D1 800
d2
DN
10
Wir behalten uns alle U

Jede Vervielfaeltigung,
Personen ist unzulaess
folgt (Urheberrechtsge
Fall der Patenterteilung
bleiben vorbehalten.
17.02.03
nd
Nr.
PN
GF / LR
GF / LR
Ers.durch dito
vom 31.10.97
nd
Nr.
Gendert
Datum/Name
Geprft
GF / LR
Gendert
Datum/Name
Geprft
Ers.durch dito
vom 31.10.97
6100.1.05.14
Gate valves
VALTRA Gate valve
700 JJ
PN 10-25
DN 300-1000
Materials
Pos.
Component
100 Body
welded on with
4 Gasket
160
170 Tension screw
190 Hexagonal nut
200 Bonnet
4 Disc
360
welded on with
4 Ball
362
4 Pressure piece
363
4 Double disc guide
365
4 Stem
400
411 Guide bushing
4 Packing
420
440 Gland flange
450 Grooved pin
462 Gland bolt
463 Washer
464 Hexagonal nut
4 Screw pin
510
4 Roller bearing
511
532 Countersink screw
590 Grease nipple
600 Handwheel
605 Key
610 Hexagonal nut
614 Retaining ring
P265GH (22)
P265GH
X20CrMo171
Sigraflex
1.7158
1.7158
P265GH
P265GH
X8CrTi18
1.4021
1.4021
P265GH
1.4021
GG 25
Graphite
P265GH
1.1181
1.1181
St
1.0501
0.7040
WLSt
8.8
5.8
St
1.0050
5.6
Spring Steel
4 Spare parts

Dimensions/mm

DN
PN
10-25
L
PN
10-25
H
PN
10-16
H1

PN
25
H1
PN
10-25
D
300
500
1165
345
345
450
350
550
1260
375
375
500
400
600
1410
420
420
600
500
700
1715
545
545
800
600
800
2035
635
655
800
700
900
2260
790
800
800
1000*
2690
1000*
800
900
1000

DN
PN
10
FL
PN
16
FL
PN
25
FL
PN
10
BW
PN
16
BW
PN
25
BW
Kvs
(m3/h)
300
320
330
360
295
295
350
390
405
445
360
360
400
540
560
610
500
500
500
815
860
945
765
765
600
1210
1270
1370
1170
1170
700
1690
1715
1980
1630
1630
800
2410
2440
3480
2330
2330
900
1000
315
380
525
850
1285
1775
2500
9230
11237
14677
23561
33929
46181
60318
*Attention: BW-overall length, DN 800, PN 25, 1250 mm

Flange-overall length, DN 800, PN 25, 1500 mm
6100.1.05.14
56
Gate valves
Gendert
Datum/Name
Geprft
VALTRA Gate valve
700 JJ
PN 40
DN 300-700
nd
Nr.
Kom. 111049 Pos.
610
KKS-NR. FEHLT
614
600
605
531
510
614
Sicherungsring
464
610
Sechskantmutter
605
Paeder
463
600
Handrad
561
Senkschraube
560
Verdrehsicherung
590
Schmiernippel
450
511
Nadellager
420
TIN
464
510
Gewindebuchse
463
Scheibe
nd
Nr.
511
440
462
H1
531
Verschraubung
Kom.
111049
Pos.
411
Baureihe: 700 JJ 22.2

fig.-no.:
190
200
170
160
400
365
Ma d1 und d2
363
420
Packung
400
Spindel
411
Fhrungshlse
KKS-NR.
FEHLT
365
Plattenhalter
363
Druckstck
362
Kugel
360
Schieberplatte
aufgepanzert mit
dimension d1 and d2
362
according to order
360
suiv. commande
dimension d1 et d2
100
Ersatzteil
spare part
Pos.
590
Benennung
Schmiernippel
531
Datum
511
10.12.01
Verschraubung
510
Name
464
Gewindebuchse

362
360
100
560
Bgelhaube
Sicherungsring
Sechskantmutter
Sechskantmutter
Schraubenbolzen
Paeder
Dichtring
Handrad
Gehuse
Senkschraube
aufgepanzert mit
Verdrehsicherung
201
614
190 2)
610
180 1)
605
160
600
100
561
piece detache
alternation
Baureihe: reserved
700 JJ 22.2
sous
reserve de modification
fig.-no.:
400
365
363
: A67G02J6
Sechskantmutter
460
Klappschraube
KENNZ.
: ENSTED
451
Kerbstift
BGR.
967110
445
Stopfbuchsbrille
gem Auftrag
610
400
614
365
600
363
605
560,561
362
531
360
510
100
590
511
464
463
445
460
451
420
412
201
190
180
160
: A67G02J6
KENNZ. : ENSTED
BGR. 967110
Gendert
Datum/Name
Geprft
610
614
600
605
560,561
531
510
590
511
464
463
445
460
451
420
412
201
190
180
160
TIN
H1
Ma d1 und d2
GF/LR
463
Nadellager
Pla
PN 40
Sechskantmutter
Scheibe
VALTRA ARMATUREN
HANDELS
460
Klappschraube
451
Kerbstift
445
Stopfbuchsbrille
420
Packung
411
Fhrungshlse
400
Spindel
365
Plattenhalter
363
Druckstck
362
Kugel
360
Schieberplatte
gem Auftrag
aufgepanzert mit
dimension d1 and d2
201
Bgelhaube
according to order
190 2)
Sechskantmutter
dimension d1 et d2
180 1) Schraubenbolzen
160
Dichtring
100
Gehuse
suiv. commande
aufgepanzert mit
Ersatzteil
Pos.
spare part
piece detache
Pla
Datum
10.12.01
Benennung
Name
GF/LR
PN 40
VALTRA ARMATUREN HANDELS

Material PN -10 20 100 120 200 250 300 350 400

P265GH 40 40 40 40 40 35 32 28 24 21
57
6100.1.05.14
Gate valves
VALTRA Gate valve
700 JJ
PN 40
DN 300-700
Materials
Pos.
Component
100 Body
welded on with
4 Seat ring
160
170 Tension screw
190 Hexagonal nut
200 Bonnet
4 Disc
360
welded on with
4 Ball
362
4 Pressure piece
363
4 Double disc guide
365
4 Stem
400
411 Guide bushing
4 Packing
420
440 Gland flange
450 Grooved pin
462 Gland bolt
463 Washer
464 Hexagonal nut
4 Yoke sleeve
510
4 Bearing
511
531 Yoke nut
600 Handwheel
605 Key
610 Hexagonal nut
614 Retaining ring
P265GH (22)
P265GH
X20CrMo171
Sigraflex
1.7158
1.7158
P265GH
P265GH
X8CrTi18
1.4021
1.4021
P265GH
1.4021
GG 25
Graphite
P265GH
1.1181
1.1181
St
1.0501
0.7040
WLSt
S355J2G3
St
1.0050
5.6
Spring Steel
4 Spare parts

Dimensions/mm

DN
L
H
Stroke
D

300
750
1260
345
500
350
850
1295
375
600
400
950
1575
445
800
500
1150
1795
525
800
600
1350
2155
640
800
700
1550
2595
770
800
800
1750

DN
FL
BW
300
350
400
500
600
700
800
440
610
890
1270
2310
3210
370
460
710
1050
1980
2960
Kvs
(m3/h)
9230
11237
14677
23561
33929
46181
6100.1.05.14
58
Gate valves
Gate valve
700 JJ
PN 160 / PD 18
DN 50-300/250
ASME
version
available
FL-
Version
Material PN -10 20 120 150 200 250 300 350 400 450 500 510 520 530 540 550

1.5415 160 160 160 160 160 160 160 139 125 118 112 72 55 43 35
1.7335 160 160 160 160 160 160 160 160 153 146 139 118 100 79 62 46 35
1.7383 160 160 160 160 160 160 160 160 153 146 139 118 100 79 70 61 52
BW-
Version
Material PD 20 50 100 120 150 200 250 300 350 400 420 430 440 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600
1.5415 18 258 246 229 219 204 185 170 146 141 136 134 133 132 130 129 128 112 88 67 53 42
1.7335 18 258 249 234 228 219 205 194 180 170 161 156 155 153 150 149 148 147 133 112 89 72 58 46 37 30
1.7383 18 258 250 239 233 224 210 205 194 180 170 166 164 162 159 156 155 153 131 115 100 88 76 66 56 50 43 37 33

59
6100.1.05.14
Gate valves
Gate valve
700 JJ
PN 160 / PD 18
Standard features
n
n
n
n
n
n
n
Die-forged body
Split disc type
Incorporated seats
Outside screw
Gasket located in a groove
Yoke sleeve with needle bearings
Universal valve head for mounting actuators
DN 50-300/250
Media
for water, gas, oil and other non aggressive medi
other

n
n
n
Pressure rating BW up to 258 bar (PD 18)

Temperature ratings up -10 C up to 600 C
Materials
n
n
n
1.5415
1.7335
1.7383
Design Highlights
Benefits
Die-forged valve body with incorporated seats
Seats and disc faced with stellite
Non-rising handwheel
Small dimensions
Non-turning, rising stem and burnished stem
Hammer head connection between wedge and stem
Gland ring and gland flange in two separate pieces
Yoke sleeve supported at the top and at the bottom by

means of needle bearings (axial type)
Valve head equipped with dirt scrapers below and

above the bearings
The wedges are able to move parallel to the axis of the

pipeline within the guiding groove. This protects the
stem against bending moments
bolts is avoided
To minimize the expenditure of effort when opening
and closing the valve
To protect against dirt and to avoid the loss

of lubricants
6100.1.05.14
60
Gate valves
Gate valve
700 JJ
PN 160 / PD 18
DN 50-300/250
610
613
600
605
540
553
542
510
511
552
464
440
462
H
430
420
412
200
190
410
170
160
400
360
361
100
363
Version DN 50 - 80
61
6100.1.05.14
Gate valves
Gate valve
700 JJ
PN 160 / PD 18
DN 50-300/250
Materials
Pos. Component

100 Body
160
4 Gasket

170 Stud
190 Hexagonal nut
200 Bonnet
360 / 361 4 Disc
363
4 Pressure piece
4 Stem
400
410 Back seat bushing
412 Guide sleeve
4 Packing
420
430 Gland ring
440 Gland flange
462 Eye bolt
464 Hexagonal nut
4 Yoke sleeve
510
4 Bearing
511
540 Flange
542 Headcap screw
552 / 553 4 Gasket
600 Handwheel
605 Key
610 Hexagonal nut
613 Screw pin
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.5415 1)
Grooved with
graphite layer
1.7709
1.7218
1.7383
1.7383 1)
1.4122
1.4923
1.4006
1.0718
Graphite
1.5415
1.5415
1.7709
1.7218
CW 713 R
WLSt
1.0425
8.8
NBR
St
1.0060
St
45H
1.7383/1.7335 1)
Grooved with
graphite layer
1.7709 2)
1.7218
1.7383
1.7383 1)
1.4122
1.4923
1.4006
1.0718
Graphite
1.5415
1.5415
1.7709
1.7218
CW 713 R
WLSt
1.0460
8.8
Viton
St
1.0060
St
45H
1.7383 1)
Grooved with
graphite layer
1.7709 2)
1.7218
1.7383
1.7383 1)
1.4122
1.4923
1.4006
1.0718
Graphite
1.5415
1.5415
1.7709
1.7218
CW 713 R
WLSt
1.0460
8.8
Viton
St
1.0060
St
45H
4 Spare parts

2) Working temperature > 550 C = Material 1.4923
Dimensions/mm

DN
L
H
50
65 / 50
80
100
125 / 100
150
200
250
300 / 250
300
360
390
450
525
600
750
900
1050
490
490
610
695
695
890
1090
1275
1275
Stroke
h
80
80
105
130
130
185
235
265
265
350
350
400
500
500
800
1000
1000
1000

DN
FL
BW
50
65 / 50
80
100
125 / 100
150
200
250
300 / 250
60
66
116
148
165
320
610
1050
1180
45
52
100
125
130
270
520
930
980
Kvs
(m3/h)
228
565
930
1995
3458
5367
5041
6100.1.05.14
62
Gate valves
700 JT
PD 10
DN 50-150
BW-
Version
Material PD 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600
1.0460 10 100 100 94 82 74 62 50 48 45 43 41 38 34 28 23

1.5415 10 120 120 112 103 88 85 82 82 81 81 80 79 79 78 78 68 53 40 32 25

1.7335 10 120 120 120 118 109 103 97 96 95 94 92 91 91 90 89 89 81 68 54 44 35 28 23 18

1.7383 10 120 120 120 120 118 109 103 102 101 99 98 97 96 95 94 89 79 69 61 53 46 40 34 30 26 22 20

63
6100.1.05.14
Gate valves
700 JT
PD 10
DN 50-150
Standard features
Media

n Full bore (Except DN 65/50 and DN 125/100)
n Yoke sleeve supported by needle bearings
n Pressure sealing bonnet
acc. VGB-guidelines

n
n
other

n
n

Materials
n
n
n
n
1.0460
1.5415
1.7335
1.7383

Design Highlights
Benefits
Die-forged valve body with integral seats
Compared to cast steel, robust and highly stressable
Hard faced seats
Full bore, except DN 65/50 and DN 125/100
Non-turning rising stem with burnished shaft
Minimum wear of the gland packing
Rolled stem thread
Possibility to add an actuator flange
Simple retrofitting of an actuator without welding
Optimal surface with higher surface hardness and

therefore better wear resistance then cut threads
6100.1.05.14
64
Gate valves
700 JT
PD 10
DN 50-150
613
610
605
600
530
510
590
511
464
462
440
420
194
190
200
H
171
170
272
271
160
270
400
360
363
DS
100
65
6100.1.05.14
Gate valves
700 JT
PD 10
DN 50-150
Materials
Pos. Component

100 Body
welded on with
4 Gasket
160
170 Stud
171 Stud
190 Hexagonal nut
194 Hexagonal nut
200 Bonnet
270 Cover
271 Ring
272 Segmentring
4 Disc
360
welded on with
4 Pressure piece
363
4 Stem
400
4 Packing
420
440 Gland flange
462 Stud
464 Hexagonal nut
4 Yoke sleeve
510
4 Roller bearing
511
530 Screwing
590 Grease nipple
600 Handwheel
605 Key
610 Hexagonal nut
613 Screw pin
1.0460 (21)
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.0460
Cr17
Graphite
1.7709
1.7709
1.7218
1.7218
1.5419
1.0460
1.0460
1.0460
1.0460
18/8 (40)
1.4021
1.4021
Graphite
1.0460
1.7709
1.7218
1.0718
WLSt
1.0718
5.8
0.7040
1.0060
St
45H
1.5415
Stellite
Graphite
1.7719
1.7719
1.7218
1.7218
1.5419
1.5415
1.5415
1.5415
1.5415
Stellite
1.4021
1.4122
Graphite
1.0460
1.7709
1.7218
1.0718
WLSt
1.0718
5.8
0.7040
1.0060
St
45H
1.7335
Stellite
Graphite
1.7709
1.7709
1.7218
1.7218
1.5419
1.7335
1.7335
1.7335
1.7335
Stellite
1.4021
1.4122
Graphite
1.0460
1.7709
1.7218
1.0718
WLSt
1.0718
5.8
0.7040
1.0060
St
45H
1.7383
Stellite
Graphite
1.7709
1.7709
1.7218
1.7218
1.5419
1.7383
1.7383
1.7383
1.7383
Stellite
1.4021
1.4122
Graphite
1.0460
1.7709
1.7218
1.0718
WLSt
1.0718
5.8
0.7040
1.0060
St
45H
4 Spare parts
Dimensions/mm

Stroke
DN
DS
L
H
h
D

50
50
250
337
63
180
65 / 50
50
290
337
63
180
80
78
310
410
90
280
100
98
350
515
110
360
125 / 100 98
400
515
110
360
150
150
450
685
165
450

DN
FL
BW
Kvs
(m3/h)
50
65 / 50
80
100
125 / 100
150
258,0
258,0
628,0
991,0
991,0
2323,0
26,5
30,5
45,0
71,0
89,0
155,0
15,5
16,0
31,0
47,0
49,0
100,0
6100.1.05.14
66
Gate valves
700 JT
PD 10
DN 200-350/300
BW-
Version
Material PD 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600
1.0460 10 100 100 94 82 74 62 50 48 45 43 41 38 34 28 23

1.5415 10 120 120 112 103 88 85 82 82 81 81 80 79 79 78 78 68 53 40 32 25

1.7335 10 120 120 120 118 109 103 97 96 95 94 92 91 91 90 89 89 81 68 54 44 35 28 23 18

1.7383 10 120 120 120 120 118 109 103 102 101 99 98 97 96 95 94 89 79 69 61 53 46 40 34 30 26 22 20

67
6100.1.05.14
Gate valves
Standard features
n
n
n
n
n
n
n

Full bore
Pressure sealing bonnet acc. VGB-guidelines
700 JT
PD 10
DN 200-350/300
Media
other

n
n

Materials
n
n
n
n
1.0460
1.5415
1.7335
1.7383
Design Highlights
Benefits
compared to cast steel, robust and highly stressable
Seats and wedge faced with stellite
Full bore
Minimize the expenditure of effort when operating valve

bolts is avoided
6100.1.05.14
68
Gate valves
700 JT
PD 10
DN 200-350/300
600
610 613
605
530
510
511
590
463 464
440
430
194
190
170
200
462
H
171
273
272
271
160
420
270
411
400
360
363
DS
100
69
6100.1.05.14
Gate valves
700 JT
PD 10
DN 200-350/300
Materials
Pos. Component

100 Body
welded on with
4 Gasket
160
170 Stud
171 Stud
190 Hexagonal nut
194 Hexagonal nut
200 Bonnet
270 Cover
271 Ring
272 Segmentring
273 Cover
4 Disc
360
welded on with
4 Pressure piece
363
4 Stem
400
4 Guide bushing
411
4 Packing
420
430 Gland ring
440 Gland flange
462 Stud
463 Washer
464 Hexagonal nut
4 Yoke sleeve
510
4 Bearing
511
530 Screwing
590 Grease nipple
600 Handwheel
605 Key
610 Hexagonal nut
613 Screw pin
1.0460 (21)
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.0460
18/8
Graphite
1.7709
1.7709
1.7218
1.7218
1.5415
1.0460
1.0460
1.0460
1.7383
1.7383
Cr17
1.4122
1.4021
1.8507
Graphite
1.0718
1.0460
1.7709
St
1.7218
CW 713 R
WLSt
1.0718
5.8
0.7040
1.0060
St
45H
1.7383/1.5415
Stellite
Graphite
1.7709
1.7709
1.7218
1.7218
1.5415
1.5415
1.5415
1.5415
1.5415
1.7383
Stellite
1.4122
1.4122
1.8507
Graphite
1.0718
1.0460
1.7709
St
1.7218
CW 713 R
WLSt
1.0718
5.8
0.7040
1.0060
St
45H
1.7383/1.7335
Stellite
Graphite
1.7709
1.7709
1.7218
1.7218
1.5415
1.7335
1.7335
1.7335
1.7335
1.7383
Stellite
1.4122
1.4122
1.8507
Graphite
1.0718
1.0460
1.7709
St
1.7218
CW 713 R
WLSt
1.0718
5.8
0.7040
1.0060
St
45H
1.7383
Stellite
Graphite
1.7709
1.7709
1.7218
1.7218
1.5415
1.7383
1.7383
1.7383
1.7383
1.7383
Stellite
1.4122
1.4122
1.8507
Graphite
1.0718
1.0460
1.7709
St
1.7218
CW 713 R
WLSt
1.0718
5.8
0.7040
1.0060
St
45H
4 Spare parts
Dimensions/mm

DN
DS
200
225 / 200
250 / 200
225 / 250
250
300 / 250
300
350 / 300
198
198
198
235
235
235
276
276
Stroke
550
600
650
600
650
750
750
850
920
920
920
1130
1130
1130
1300
1300
210
210
210
265
265
265
310
310
D
600
600
600
720
720
720
900
900

Kvs
DN
BW
(m3/h)
200
225 / 200
250 / 200
225 / 250
250
300 / 250
300
350 / 300
260
270
280
530
550
580
850
870
4000
6247
8997
9257
6100.1.05.14
70
Gate valves
700 JT
PD 10
DN 350-700
ASME
version
available
BW-
Version
Material PD 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650
1.0425 10 100 100 94 82 74 62 50 48 45 43 41 38 34 28 23

1.5415 10 120 120 112 103 88 85 82 82 81 81 80 79 79 78 78 68 53 40 32 25

1.7335 10 120 120 120 118 109 103 97 96 95 94 92 91 91 90 89 89 81 68 54 44 35 28 23 18

1.7383 10 120 120 120 120 118 109 103 102 101 99 98 97 96 95 94 89 79 69 61 53 46 40 34 30 26 22 20
1.4903 10 136 136 136 136 136 136 136 136 136 136 136 136 136 136 134 122 119 110 101 93 84 76 68 61 54 48 42 37 32 27 24 21

71
6100.1.05.14
Gate valves
Standard features
n
n
n
n
n
n

Easy assembly of an E-actuator
700 JT
PD 10
DN 350-700
Media
other

n
n

Materials
n
n
n
n
n
1.0425
1.5415
1.7335
1.7383
1.4903
Design Highlights
Benefits
Seats and disc faced with stellite
Pressure sealed bonnet

bolts is avoided
6100.1.05.14
72
Gate valves
700 JT
PD 10
DN 350-700
618
617
616
605
531
511
510
718
715
710
420
464
421
440
194
430
190
H
170
462
200
273
272
171
271
160
270
411
400
360
361
363
DS
100
73
6100.1.05.14
Gate valves
700 JT
PD 10
DN 350-700
Materials
Pos. Component

100 Body
welded on with
4 Gasket
160
170 Stud
171 Stud
190 Hexagonal nut
194 Hexagonal nut
200 Bonnet
270 Cover
271 Ring
272 Segmentring
273 Cover
Disc
360 / 361 4
welded on with
4 Pressure piece
363
4 Stem
400
4 Guide bushing
411
4 Packing
420
430 Gland ring
440 Gland flange
462 Stud
464 Hexagonal nut
4 Yoke sleeve
510
4 Bearing
511
531 Yoke nut
605 Key
616 Screw pin
617 Screw pin
618 Hexagonal nut
710 Switch bracket
715 Key
718 Washer
1.0425 (22)
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.4903 (63)
1.0425
Stellite
Graphite
1.7709
1.7709
1.7218
1.7255
1.5415
1.0460
1.0460
1.0460
1.0460
1.0460
Stellite
1.4122
1.4021
1.8507
Graphite
1.5415
1.0460
1.7709
1.7218
CW 713 R
WLSt
1.7335
1.0060
1.0460
45H
St
1.0425
1.4021
1.0038
1.5415
Stellite
Graphite
1.7709
1.7709
1.7218
1.7218
1.5415
1.5415
1.5415
1.5415
1.0460
1.5415
Stellite
1.4122
1.4923
1.8507
Graphite
1.5415
1.5415
1.7709
1.7218
CW 713 R
WLSt
1.7335
1.0060
1.0460
45H
St
1.0425
1.4021
1.0038
1.7335
Stellite
Graphite
1.7709
1.7709
1.7218
1.7218
1.5415
1.7335
1.7335
1.7335
1.0460
1.7335
Stellite
1.4122
1.4923
1.8507
Graphite
1.5415
1.7335
1.7709
1.7218
CW 713 R
WLSt
1.7335
1.0060
1.0460
45H
St
1.0425
1.4021
1.0038
1.7383
Stellite
Graphite
1.7709
1.7709
1.7218
1.7218
1.5415
1.7383
1.7383
1.7383
1.0460
1.7383
Stellite
1.4122
1.4923
1.8507
Graphite
1.5415
1.7383
1.7709
1.7218
CW 713 R
WLSt
1.7335
1.0060
1.0460
45H
St
1.0425
1.4021
1.0038
1.4903
Stellite
Graphite
1.7709
1.7709
1.7218
1.7218
1.5415
1.4903
1.4903
1.4903
1.0460
1.4903
Stellite
1.4122
1.4923 / 1.4980
1.8507
Graphite
1.5415
1.7383
1.7709
1.7218
CW 713 R
WLSt
1.7335
1.0060
1.0460
45H
St
1.0425
1.4021
1.0038
4 Spare parts
Dimensions/mm
DN

350
400
450
500
600
700
DS
L
H
Stroke

330
850
1730
365
375
950
1850
415
419
1050
2070
465
464
1150
2300
515
559
1350
2765
625
640
1550
2895
690

DN
BW
350
400
450
500
600
700
995
1600
2000
2490
4550
5750
Kvs
(m3/h)
11243
14521
18105
22353
32188
41773
6100.1.05.14
74
Gate valves
700 JT
PD 25 / PD 40
DN 65-300
ASME
version
available
BW-
Version
Material PD

20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650

1.0460 25 250 250 250 250 250 235 206 184 155 125 119 113 107 102 96 85 71 58

1.5415 25 300 300 300 300 300 280 258 221 213 206 205 203 202 200 199 197 196 194 170 132 101 79 64

1.7335 25 300 300 300 300 300 300 294 272 258 243 240 237 234 231 228 227 225 224 222 202 170 134 109 88 69 57 46

1.7383 25 300 300 300 300 300 300 300 294 272 258 255 252 249 246 243 240 237 234 224 199 174 152 132 115 100 85 75 65 56 49

1.6368 25 410 410 410 410 410 410 410 410 410 410 410 410 410 402 360 309 257 205 153 102

1.4903 25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 418 383 372 344 316 290 263 238 213 191 169 150 132 115 100 85 75 64
1.4901 25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 423 397 370 345 320 297 275 252 230 208 186 166 147 127 110 95 82

1) Operating temperature = design temperature minus temperature surcharge acc. to DIN regulations. For temperatures > 570 C stem in 1.4980
BW-
Version
Material PD

20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650

1.0460 40 400 400 400 400 400 377 330 295 248 200 190 181 172 162 153 135 113 93

1.5415 40 480 480 480 480 480 447 412 353 341 330 327 325 322 320 318 315 313 311 271 212 161 127 101

1.7335 40 481 481 481 481 481 481 471 436 412 388 384 379 374 370 365 363 360 358 355 322 271 215 175 141 110 90 73

1.7383 40 480 480 480 480 480 480 480 471 436 412 407 403 398 393 388 384 379 374 358 318 278 242 212 183 160 136 120 103 89 79

1.6368 40 657 657 657 657 657 657 657 657 657 657 657 657 657 643 577 495 412 328 245 163

1.4903 40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 669 612 596 551 506 464 421 381 341 306 271 240 212 183 160 136 120 103
1.4901 40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 677 635 592 552 512 475 440 404 369 334 298 265 235 204 176 152 131

75
6100.1.05.14
Gate valves
Standard features
n
n
n
n
n
n
n
n
Body made of forged steel

Disc guided in groove
Welded seat rings
Position indicator / Switch bracket
Pressure sealing bonnet acc. to VGB-guidelines
Possibility to add an actuator
700 JT
PD 25 / PD 40
DN 65-300
Materials
n
n
n
n
n
n
n
1.0460
1.4901
1.4903
1.5415
1.6368
1.7335
1.7383

Media
n
n


High temperature steam and water, refining
(catalytic reformers and hydrocrackers),
petrochemical and chemical industries
Design Highlights
n
Long bonnet
Seats of the shut-off device and of the valve body

generally faced with stellite
Benefits
n
Best possible sliding performance and minimum wear
Non-rising handwheel
Small dimensions
Outside located switch-bracket
Protects against torsion of the stem
Hammer head connection between shut-off

device and stem
Yoke sleeve supported at the top and at the bottom

by means of needle bearings (axial type)
The wedges are able to move parallel to the axis of the

pipeline within the guiding groove. This protects the
stem against bending moments

bolts is avoided
6100.1.05.14
76
Gate valves
DSK 26
700 JT
PD 25
PD 25 / PD 40
DN 80-300
DN 65-250
DN 65-300
510
511
200
464
H1
462
H2
440
190
420
170
273
272
271
270
160
DS
400
360
100
DSK 26
PD 40
510
511
200
464
440
462
H1
170
H
190
H2
420
273
272
271
270
160
400
100
DS
360
77
6100.1.05.14
Gate valves
700 JT
PD 25 / PD 40
DN 65-300
1.6368 (46)
1.4903 (63)
1.4901 (66)
1.4903
Stellite
Graphite
1.7709
1.7218
1.5419
1.4903
1.4903
1.4903
1.5419
1.4903
Stellite
1.4923
1.4980
Graphite
1.7380
1.4923
1.4923
CW713R
WLSt
1.4901
Stellite
Graphite
1.7709
1.7218
1.5419
1.4901
1.4901
1.4901
1.5419
1.4901
Stellite
1.4980
Materials
Pos. Component
1.0460 (21)
1.5415 (42)
1.7335 (44)

100 Body
1.0460
1.5415
1.7335
welded on with
Stellite
Stellite
Stellite
4 Gasket
Graphite
Graphite
Graphite
160
170 Stud
1.7709
1.7709
1.7709
190 Hexagonal nut
1.7218
1.7218
1.7218
200 Bonnet
1.5419
1.5419
1.5419
270 Cover
1.7383
1.7383
1.7383
271 Ring
1.7383
1.7383
1.7383
272 Segmentring
1.7383
1.7383
1.7383
273 Cover
1.5419
1.5419
1.5419
4 Disc
1.7383
1.7383
1.7383
360
welded on with
Stellite
Stellite
Stellite
4 Stem
1.4122
1.4122
1.4122
400
4 Stem from 570 C
400
4 Packing
Graphite
Graphite
Graphite
420
440 Gland flange
1.7380
1.7380
1.7380
462 Stud
1.7709
1.7709
1.7709
464 Hexagonal nut
1.7218
1.7218
1.7218
4 Yoke sleeve
CW713R
CW713R
CW713R
510
4 Bearing
WLSt
WLSt
WLSt
511
1.7383 (45)
1.7383
1.6368
Stellite
Stellite
Graphite
Graphite
1.7709
1.7709
1.7218
1.7218
1.5419
1.5419
1.7383
1.4903
1.7383
1.4903
1.7383
1.4903
1.5419
1.5419
1.7383
1.4903
Stellite
Stellite
1.4122
1.4923
1.4980
Graphite
Graphite
1.7380
1.7380
1.7709
1.4923
1.7218
1.4923
CW713R
CW713R
WLSt
WLSt
Graphite
1.7380
1.4923
1.4923
CW713R
WLSt
4 Spare parts
Dimensions/mm DSK 26.25

DN
DS
L
H
H1
H2
Stroke R/Stroke H-Wheel

mm
mm
mm
mm
mm
mm

80
70
305
556
605
511
80
16
400
100
90
406
658
725
606
105
18
450
125
111
483
781
861
720
130
21
500
150
136
559
952
1045
872
152
22
200
178
711
1078
1270
1045
192
24
250
222
864
1267
1515
1240
248
28
300
263 770 (991)
1528
1815
1497
287
29

DIN/ISO
5210
F10 (F14)
F14
F14
F16 (F14)
F25 (F16)
F30 (F25)
F30
Dimensions/mm DSK 26.40

DN
DS
L
H
H1
H2
Stroke R/Stroke
H-Rad

mm
mm
mm
mm
mm
mm

65
50
330
518
594
466
66
19
400
80
57
368
638
675
585
73
21
450
100
72
457
713
836
656
87
15
500
125
90
533
795
870
725
106
15
150
111
610
1090
1230
1040
133
15
200
146
762
1195
1370
1165
174
18
250
185
1270
1475
1685
1440
212
21

DN
BW
Kvs
(m3/h)

80
72
505
100
128
875
125
208
1270
150
380
1910
200
615
3270
250
1160
5080
300
1835
7140

DIN/ISO
5210
F10 (F14)
F14
F14
F16
F25 (F16)
F30 (F25)
F35 (F30)

DN
BW
Kvs
(m3/h)

65

83
210
80
136
310
100
219
505
125
411
835
150
676
1485
200
1188
2200
250
2208
3530
6100.1.05.14
78
Gate valves
High pressure gate valve DSK 16-63
700 JT
PD 16-63
DN 50-600
ASME
version
available
BW-
Version
Material PD 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650
1.0460 16 160 160 151 132 118 99 80 76 73 69 65 61 54 45 37
25 250 250 235 206 184 155 125 119 113 107 102 96 85 71 58
32 320 320 302 264 236 198 160 153 145 138 130 123 109 91 75
40 400 400 377 330 295 248 200 191 182 172 163 153 136 113 93

1.5415 16 192 192 179 165 141 137 132 131 130 129 128 127 126 125 124 109 85 64 51 41
25 300 300 280 258 221 213 206 205 203 202 200 199 197 196 194 170 132 101 79 64
32 385 385 358 330 283 273 264 262 260 258 256 255 253 251 249 217 170 129 102 81
40 480 480 448 413 354 342 330 328 325 323 321 318 316 314 311 272 212 161 127 102

1.7335 16 192 192 192 189 174 165 156 154 152 150 148 146 145 144 143 142 129 109 86 70 57 44 36 29
25 300 300 300 294 272 258 243 240 237 234 231 228 227 225 224 222 202 170 134 109 88 69 57 46
32 385 385 385 377 349 330 311 307 304 300 296 292 290 289 287 285 258 217 172 140 113 88 72 59
40 481 481 481 471 436 413 389 384 380 375 370 365 363 364 358 356 323 272 215 175 141 110 91 74

1.7383 16 192 192 192 192 189 174 165 163 161 159 157 156 154 152 150 143 127 111 97 85 74 64 55 48 41 36 32
25 300 300 300 300 294 272 258 255 252 249 246 243 240 237 234 224 199 174 152 132 115 100 85 75 65 56 49
32 384 384 384 384 377 349 330 326 322 319 315 311 307 304 300 287 255 223 194 170 147 128 109 96 83 72 63
40 480 480 480 480 471 436 413 408 403 398 384 389 384 379 375 358 318 278 243 212 184 160 137 120 104 90 79

1.6368 16 263 263 263 263 263 263 263 263 263 263 257 231 198 165 131 98 65
25 410 410 410 410 410 410 410 410 410 410 402 360 309 257 205 153 102
32 525 525 525 525 525 525 525 525 525 525 515 482 396 330 262 196 130
40 657 657 657 627 657 657 657 657 657 657 643 577 495 412 328 245 163

1.4903 16 272 272 272 272 272 272 272 272 272 272 272 272 272 272 268 245 239 221 203 186 169 153 137 123 108 96 85 74 64 55 48 41
25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 418 383 372 344 316 290 263 238 213 191 169 150 132 115 100 85 75 65
32 544 544 544 544 544 544 544 544 544 544 544 544 544 544 536 490 477 441 405 371 338 305 273 245 217 192 170 147 128 109 96 83
40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 669 613 596 552 507 464 422 382 342 306 271 240 212 184 160 137 120 104
1.4901

16
25
32
40
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
271
423
542
677
254
397
508
635
237
370
474
592
221
345
442
552
205
320
410
512
190
297
380
475
176
275
352
440
161
252
323
404
147
230
295
369
133
208
267
334
119
186
239
298
106
166
212
265
94
147
188
235
81
127
163
204
70
110
141
176
61
95
122
152
52
82
105
131
1) Operating temperature = design temperature minus temperature surcharge acc. to DIN regulations. Design according to working data PD 63 on request
79
6100.1.05.14
Gate valves
Standard features
Valve body made of forged steel
Split disc type
n Welded seatrings and guide bars
n Position indicator / non-rotating device
acc. VGB-guidelines
n Yoke sleeve supported by needle bearing
n Possibility to add an actuator
700 JT
n
n
n

Higher temperature ratings on request
PD 16-63
DN 50-600
Materials
n
n
n
n
n
1.0460
1.4901
1.4903
1.5415
1.7335
1.7383
1.6368
Media
reformers and hydrocrackers), petrochemical and
chemical industries
Design Highlights
Benefits
Long bonnet
Seats and discs faced with stellite
Best possible sliding performance and minimum wear
Outside located switch bracket
Protects against torsion
Hammer head connection between

shut-off device and stem
Wedge are able to aligne parallel to the axis of the

pipe shut-off device and stem within the guiding
groove. This protects the stem against bending
moments
Damage to the stem by irregular tightening of

gland bolts is avoided
Minimize the expenditure of effort
when operating valve
6100.1.05.14
80
Gate valves
700 JT
PD 16-63
DN 50-600
617 618
h
616
605
551
540
511
510
225
550
542 543
400
711 712
718
710 715
462 463
Drawing
464
rotated
448
by 90
440
190
170
200
430
273
171
411 420
272
271
160
411
270
360
361
363
DS
100
81
6100.1.05.14
Gate valves
700 JT
PD 16-63
DN 50-600
Materials
Pos. Component

100 Body
welded on with
4 Gasket
160
170 Stud
171 Stud
190 Hexagonal nut
200 Bonnet
225 Yoke head
270 Cover
271 Ring
272 Segmentring
273 Cover
360 / 361 4 Disc
welded on with
4 Pressure piece
363
4 Stem
400
4 Guide bushing
411
4 Packing
420
4 Ring
421
430 Gland ring
440 Gland flange
4 Dirt scraper
448
462 Stud
463 Washer
464 Hexagonal nut
4 Yoke sleeve
510
4 Bearing
511
540 Flange
542 Headcap screw
543 Hexagonal nut
550 / 551 4 Gasket
605 Key
616 Screw ring
617 Screw pin
618 Hexagonal pipe nut
710 Switch bracket
711 Hexagonal screw
712 Hexagonal nut
715 Key
718 Washer
1.0460 (21)
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.6368 (46)
1.4903 (63)
1.4901 (66)
1.0460
Stellite
Graphite
1.7709
1.7709
1.7218
1.5415
1.0460
1.0460
1.0460
1.0460
1.0460
1.0460
Stellite
1.4122
1.4921
1.8507
Graphite
Graphite
1.5415
1.0460
Graphite
1.7709
St
1.7218
CW 713 R
WLSt
1.0425
8.8
8
NBR
1.0060
1.0460
45H
St
1.0425
8.8
8
1.4021
1.0038
1.5415
Stellite
Graphite
1.7709
1.7709
1.7218
1.5415
1.0460
1.5415
1.5415
1.5415
1.5415
1.5415
Stellite
1.4122
1.4021
1.8507
Graphite
Graphite
1.5415
1.5415
Graphite
1.7709
St
1.7218
CW 713 R
WLSt
1.0425
8.8
8
NBR
1.0060
1.0460
45H
St
1.0425
8.8
8
1.4021
1.0038
1.7335
Stellite
Graphite
1.7709
1.7709
1.7218
1.5415
1.0460
1.7335
1.7335
1.7335
1.7335
1.7335
Stellite
1.4122
1.4923
1.8507
Graphite
Graphite
1.5415
1.7335
Graphite
1.7709
St
1.7218
CW 713 R
WLSt
1.0425
8.8
8
NBR
1.0060
1.0460
45H
St
1.0425
8.8
8
1.4021
1.0038
1.7383
Stellite
Graphite
1.7709
1.7709
1.7218
1.5415
1.0460
1.7383
1.7383
1.7383
1.7383
1.7383
Stellite
1.4122
1.4923
1.8507
Graphite
Graphite
1.5415
1.7383
Graphite
1.7709
St
1.7218
CW 713 R
WLSt
1.0425
8.8
8
NBR
1.0060
1.0460
45H
St
1.0425
8.8
8
1.4021
1.0038
1.6368
Stellite
Graphite
1.7709
1.7709
1.7218
1.5415
1.0460
1.6368
1.6368
1.6368
1.6368
1.6368
Stellite
1.4122
1.4923
1.8507
Graphite
Graphite
1.5415
1.6368
Graphite
1.4923
St
1.4923
CW 713 R
WLSt
1.0425
8.8
8
NBR
1.0060
1.0460
45H
St
1.0425
8.8
8
1.4021
1.0038
1.4903
Stellite
Graphite
1.7709
1.7709
1.7218
1.5415
1.0460
1.4903
1.4903
1.4903
1.4903
1.4903
Stellite
1.4122
1.4923
1.8507
Graphite
Graphite
1.5415
1.4903
Graphite
1.4923
St
1.4923
CW 713 R
WLSt
1.0425
8.8
8
NBR
1.0060
1.0460
45H
St
1.0425
8.8
8
1.4021
1.0038
1.4901
Stellite
Graphite
1.7709
1.7709
1.7218
1.5415
1.0460
1.4901
1.4901
1.4901
1.4901
1.4901
Stellite
1.4122
1.4980
1.8507
Graphite
Graphite
1.5415
1.4903
Graphite
1.4980
St
1.4980
CW 713 R
WLSt
1.0425
8.8
8
NBR
1.0060
1.0460
45H
St
1.0425
8.8
8
1.4021
1.0038
4 Spare parts
Dimensions/mm, Weights/kg and Kvs-values

DSK 16
DSK 25
DSK 32
DSK 40
DSK 63
KV
DN
DS
L
H Stroke h
kg
L
H Stroke h
kg
L
H Stroke h
kg
H Stroke h
kg
H Stroke h
kg (m3/h)

65 - 200
Version DSK 26.40
Version DSK 26.40
225
202,5 1050 1720
240 1980 4221
250 / 225 202,5 1150 1720
240
250
225,0
Version DSK 26.25
Version DSK 26.25
1150 1980
270 2300
On request
On request 5211
300 / 250 225,0 1350 1980
270
300
270,0 1350 2195
305 3600 7504
350 / 300 270,0 1550 2195
305
350
315,0
1200 2140
350 2230 1550 2280
350 3750 1550 2400
350 5840 10214
400 / 350 315,0
1350 2140
350 1750 2280
350 1750 2400
350
400
360,0
1350 2320
400 3000 1750 2565
410 5500 1750 2700
410 8200 13340
450 / 400 360,0
1500 2320
400 1950 2565
410 1950 2700
410
450
405,0
1500 2485
445 3935 1950 2850
460 7700 16884
500 / 450 405,0
1650 2485
445 2150 2850
460
On request
500
450,0
1650 2850
495 5400 20844
600 / 500 540,0
On request
600
540,0
On request 30015

6100.1.05.14
82
Gate valves
Over-pressure-safety devices
If a closed gate valve filled with a medium (e.g. water)

(fig. 1) is heated, an unacceptably high pressure may
develop inside the body. The level of increase in pressure
that may occur depends upon the percentage volumes
of the fluid and vapour phases and on the increase in
the temperature of the medium. Overpressure inside the
body can adversely affect the operation of the gate valve.
Moreover an unacceptably high pressure load can result
in the failure of the pressure-retaining components.
closed nozzle
Fig. 1
medium enclosed in
the 3rd chamber
closed nozzle
500
Simple and effective protection against overpressure can

be achieved by means of a hole in the seat ring or in the
wedge on the side facing the pressure (Fig. 4). This hole
prevents the pressure inside the body from exceeding
the operating pressure; however, the gate valve can then
only provide a seal in one direction. If this is the case,
the direction of flow is shown by an arrow on the body.
Another possibility is an equalizing pipe connection to the
third room (Fig. 5) with the pressurized side.
20
30
50
70
80
400
10
350
300
250
200
150
3
100
Percentage volume of water (%)
Fig. 6 includes a pressure equalizing pipe to reduce the

opening torque with differential pressure, this configuration also enables the 3rd chamber to be relieved to the
high pressure side. Bi-directional flow characteristics are
achivable with this design.
450
Pressure of enclosed water (bar)
In case an outside overpressure safety device should

be assigned body has to be ordered with an appropriate
closed stud (Fig. 1 and 3).
90
Fig. 2
95
Attention: If there is a possibility of an unacceptable

pressure load of this kind developing inside the valve
because of the way it has been fitted or the way it is
used, the piping designer or operator must provide a suitable safety device.
100
Figure 2 shows the increase of pressure according to

percentage volume and temperature changes, when
water is in the body.
50
0
100
200
300
400
500
600
Temperature (C)
Fig. 3: With safety valve
83
6100.1.05.14
Fig. 4: With hole in the disc or seatring
Fig. 5: With equalizing pipe to the 3rd chamber
Fig. 6: With equalizing pipe and bypass valves
Gate valves
Over-pressure-safety devices
PERSTA Type SV 97 / SV 98 / SV 99
Assembly Sketch SV 97
Electronic
monitoring
Optional with
burst disc
Assembly Sketch SV 98
B
Installation:
Outlet A
Vertical downwards!
A: Blow-off stud
B: Steam-releasing-pipe
Optional
Electronic
sensor
Burst disc
Assembly Sketch SV 99 with lockable high pressure globe valve
Optional
Electronic
burst
monitoring
Burst disc
6100.1.05.14
84
Gate valves
85
Variants
Universal valve head for

mounting actuators
Stuffing box with central

plate-spring tightening
Position indicator /
Stem protection cap
Limit switch actuation
PERLOC-system locking device
Interlocking device
6100.1.05.14
Gate valves
Variants
Drainage stud,
variable position
Pos. L
Pos. A
Pos. F
Pos. S
Flow
direction
100
Pos. H
Pos. K
Pos. B
Pos. C
Pos. M
Pos. D
Pos. Y
Pos. 0
Pos. F
Pos. N
Pos. E
Water gland ring /

leakage suction
Pos. S
Pos. G
Stuffing box extrusion
6100.1.05.14
86
Swing check valves
640 AA
PN 10-40
DN 50-250
Material PN -10 20 120 150 200 250 300 350 400

1.0619 10-16 16 16 16 15 14 13 11 10 8
25 25 25 25 23 22 20 17 16 13
40 40 40 40 37 35 32 28 24 21

Operating temperature = design temperature minus temperature surcharge acc. to DIN regulations.
87
6100.1.05.14
Swing check valves
640 AA
PN 10-40
DN 50-250
Standard features
n
n
Body cast steel


n
n

Media
Depending on the material swing check valves are suitable for water, gas, oil and other non aggressive media
other
Materials
n
1.0619
Design Highlights
Hard faced integral body seat with 13 % Cr-Steel
or 17 % Cr-Steel layer
Shut-off disc with curved journal within lever
The lever rests on the hinge pin by means

of a separate bearing bush
Benefits
n
To improve movability and therefore to improve the

alignment of the disc to the body seat
Improved resistance to wear by means of proper

material selection
6100.1.05.14
88
Swing check valves
640 AA
PN 10-40
DN 50-250
FL-Version
D
190
170
210
160
H
382
384
385
387
380
100
470
469
411
405
EE-Version
89
6100.1.05.14
Swing check valves
640 AA
PN 10-40
DN 50-250
Materials
Pos. Component

100 Body
welded on with
4 Gasket
160
170 Stud
190 Hexagonal nut
210 Bonnet
4 Disc
380
welded on with
382
4 Hinge
4 Bushing
384
4 Pint
385
387 Washer
4 Hinge pin
405
4 Guide bushing
411
4 Gasket
469
470 Screw plug
1.0619 (11)
1.0619
Cr17
Graphite 2)
1.1181
1.1181
1.0460
1.4021
1)
1.0425
1.4006
1.4370
1.4021
1.4021
1.4006
2.4066
1.7709
4 Spare parts

1) DN 125 1.0460 welded on with Cr17
2) DN 150 grooved with graphite layer
Dimensions/mm

DN
L
H
D

50 230
165
172
65 290
185
212
80 310
210
227
100 350
225
257
125 400
255
292
150 480
310
327
200 600
370
412
250 730
435
462

Kvs
DN
FL
BW
(m3/h)

50
19
13

65
31
23
170
80
36
27
256
100
52
39
400
125
70
53
625
150
104
82
900
200
146
108
1600
250
289
249
2500
6100.1.05.14
90
Swing check valves
VALTRA Swing check valve
640 AA
PN 10-40
DN 300-800
Material PN -10 20 100 120 200 250 300 350 400

P265GH 10 10 10 10 10 9 8 7 6 5
16 16 16 16 16 14 13 11 10 8
25 25 25 25 25 22 20 17 16 13
40 40 40 40 40 35 32 28 24 21
Operating temperature = design temperature minus temperature surcharge acc. to DIN regulations.
91
6100.1.05.14
Swing check valves
Standard features
n
n
n
Disc with inside shaft

Body pressed-plate welding construction

n
n

640 AA
PN 10-40
DN 300-800
Media
Depending on the material swing check valves are
suitable for water, gas, oil and other non aggressive
media
other
Material
n
P265GH

Design Highlights
Benefits
Body- and disc seat welded on
Extemely resistant to wear
Disc with flexible shaft at the hinge
Optimum alignment of the disc to the body seat
Lever rests on the hinge pin by means of a separate

bushing
Inside shaft
Improved resistance wear by means of an optimal

material selection
Limited leckage due to less sealings
6100.1.05.14
92
dert
Name
rft
nd
Nr.
n
Swing check valves
640 AA
PN 10-40
DN 300-800
801
190
170
210
20.03.07
GF / LR
382
26.01.07
GF / LR
23.11.04
GF / LR
16.07.04
GF / LR
30.10.03
GF / LR
GF / LR
Ers. fr dito
vom 20.11.99
Gendert
405
160
385
nd
380
100
Ersatzteil
L
spare part
801
piece detache
419
407
405
nderungen vorbehalten 392

93
389
388

6100.1.05.14
Technical
Baureihe:
640alterations
AA 22.2reserved
fig.-no.:
386
384
Swing check valves
640 AA
PN 10-40
DN 300-800
Materials
Pos. Component

100 Body
welded on with
4 Gasket
160
170 Tension screw
190 Hexagonal nut
210 Bonnet
4 Disc
380
welded on with
4 Hinge
382
4 Pint
385
4 Hinge pin
405
801 Lifting eye bolt

P265GH (22)
P265GH
X20CrMo171
1.4541 / Graphite
1.7158
1.7158
P265GH
P265GH
X8CrTi18
S235JRG2
A2-70
1.4021
S355J2G3
4 Spare parts
Dimensions/mm
PN
PN
PN
PN
PN
PN
PN
10-16 25-40 10-16
25
40 10-16
25
DN
L
L
H
H
H
D
D

300 700
850
385
415
435
525
350 800
980
430
450
485
630
400 900 1100
500
540
595
745
500 1100 1250
585
615
670
870
870
600 1300 1450 1040
700 1500 1650
800 1700 1850

PN
40
D
525
640
755
890
1040
PN
PN
PN
PN
PN
PN
PN
PN
10
16
25
40
10
16
25
40
Kvs
DN FL
FL
FL
FL
BW
BW
BW
BW (m3/h)

300 275
285
350
430
255
255
305
355 3600
350 380
395
475
550
335
345
395
445 4900
400 560
575
735
895
525
525
365
745 6400
500 910
945 1180 1300
860
860 1040 1125 9996
600 14395
700 19593
800 25591
6100.1.05.14
94
Swing check valves
640 AA
PN 63-160 (PD 18)
DN 50-300/250
ASME
version
available
FL-
Version
Material PN -10 20 120 150 200 250 300 350 400 450 500 510 520 530 540 550

1.5415 63 63 63 63 63 63 63 53 50 47 45 29 22 16 14
1.7335 63 63 63 63 63 63 63 63 61 58 56 47 40 32 25 20 15
1.7383 63 63 63 63 63 63 63 63 61 58 56 47 40 32 28 24 20
FL-
Version
Material PN -10 20 120 150 200 250 300 350 400 450 500 510 520 530 540 550

1.5415 100 100 100 100 100 100 100 87 78 74 70 45 34 27 22
1.7335 100 100 100 100 100 100 100 100 95 91 87 74 62 49 38 31 24
1.7383 100 100 100 100 100 100 100 100 95 91 87 74 62 49 43 37 31
FL-
Version
Material PN -10 20 120 150 200 250 300 350 400 450 500 510 520 530 540 550

1.5415 160 160 160 160 160 160 160 139 125 118 112 72 55 43 35
1.7335 160 160 160 160 160 160 160 160 153 146 139 118 100 79 62 46 35
1.7383 160 160 160 160 160 160 160 160 153 146 139 118 100 79 70 61 52
BW-
Version
Material PD -10 20 50 100 120 150 200 250 300 350 400 420 430 440 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600

1.5415 18 258 258 246 229 219 204 185 170 146 141 136 134 133 132 130 129 128 112 88 67 53 42
1.7335 18 258 258 249 234 228 219 205 194 180 170 161 156 155 153 150 149 148 147 133 112 89 72 58 46 37 30
1.7383 18 258 258 250 239 233 224 210 205 194 180 170 166 164 262 159 156 155 153 131 115 100 88 76 66 56 50 43 37 33

95
6100.1.05.14
Swing check valves
640 AA
PN 63-160 (PD 18)
Standard features
n
n
n
n
Die-forged body
Disc with inside shaft
Fastening of the disc at the cover
DN 50-300/250
Media
n
n
n

other
Pressure rating BW-Ends 258 bar (PD 18)

Temperature rating up -10 C to 600 C
Materials
n
n
n
1.5415
1.7335
1.7383
Design Highlights
Benefits
Die-forged body
Integral seat
No contact corrosion
Lever rests on the hinge pin

by means of the guide bush
Optimum adjustment of the disc to the body seat by

means of the movability the guide bushing
To improve the stress capacity when temperature and

pressure changes
Bolted bonnet with reduced-shaft bolts
Fastening of the disc at the cover
Easy to assemble and disassemble
6100.1.05.14
96
Swing check valves
640 AA
PN 63-160 (PD 18)
DN 50-300/250
801
190
210
170
160
405
409
380
100
97
6100.1.05.14
Swing check valves
640 AA
PN 63-160 (PD 18)
DN 50-300/250
Materials
Pos. Component

100 Body
welded on with
4 Gasket
160
170 Stud
190 Hexagonal nut
210 Bonnet
4 Disc
380
welded on with
4 Hinge pin
405
4 Guide bush
409
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.5415
Stellite
Graphite
1.7709
1.7218
1.5415
1.5415
Stellite
1.4021
5.3106
1.0401
1.7383/1.7335
Stellite
Graphite
1.7709
1.7218
1.7335
1.7335
Stellite
1.4021
5.3106
1.0401
1.7383
Stellite
Graphite
1.7709
1.7218
1.7383
1.7383
Stellite
1.4021
5.3106
1.0401
4 Spare parts
Dimensions/mm
PN
63-100
DN
L
PN
160
L
50
65 / 50
80
100
125 / 100
150
200
250
300 / 250
300
360
390
450
525
600
750
900
1050
220
220
280
320
320
410
510
595
595
250
340
380
430
500
550
650
775
900
D
192
192
236
265
265
350
440
550
550
Weights/kg
DN
50
65 / 50
80
100
125 / 100
150
200
250
300 / 250
FL
BW
45
53
83
105
111
270
425
525
610
35
43
63
100
106
220
365
750
800
6100.1.05.14
98
High pressure swing check valves
DRI 26
640 AB
PD 25 / PD 40
DN 65-300
ASME
version
available
BW-
Version
Material PD

20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650

1.0460 25 250 250 250 250 250 235 206 184 155 125 119 113 107 102 96 85 71 58

1.5415 25 300 300 300 300 300 280 258 221 213 206 205 203 202 200 199 197 196 194 170 132 101 79 64

1.7335 25 300 300 300 300 300 300 294 272 258 243 240 237 234 231 228 227 225 224 222 202 170 134 109 88 69 57 46

1.7383 25 300 300 300 300 300 300 300 294 272 258 255 252 249 246 243 240 237 234 224 199 174 152 132 115 100 85 75 65 56 49

1.6368 25 410 410 410 410 410 410 410 410 410 410 410 410 410 402 360 309 257 205 153 102

1.4903 25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 418 383 372 344 316 290 263 238 213 191 169 150 132 115 100 85 75 64
1.4901 25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 423 397 370 345 320 297 275 252 230 208 186 166 147 127 110 95 82

BW-
Version
Material PD

20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650

1.0460 40 400 400 400 400 400 377 330 295 248 200 190 181 172 162 153 135 113 93

1.5415 40 480 480 480 480 480 447 412 353 341 330 327 325 322 320 318 315 313 311 271 212 161 127 101

1.7335 40 481 481 481 481 481 481 471 436 412 388 384 379 374 370 365 363 360 358 355 322 271 215 175 141 110 90 73

1.7383 40 480 480 480 480 480 480 480 471 436 412 407 403 398 393 388 384 379 374 358 318 278 242 212 183 160 136 120 103 89 79

1.6368 40 657 657 657 657 657 657 657 657 657 657 657 657 657 643 577 495 412 328 245 163

1.4903 40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 669 612 596 551 506 464 421 381 341 306 271 240 212 183 160 136 120 103
1.4901 40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 677 635 592 552 512 475 440 404 369 334 298 265 235 204 176 152 131

99
6100.1.05.14
DRI 26
Standard features
n
n
n
n

Swing check valve with internal hinge pin
Lever rests in separate support ring
640 AB
PD 25 / PD 40
DN 65-300
Media
Depending on the material swing check valves are
suitable for water, gas, oil and other non aggressive
media
n
n


other
Materials
n
n
n
n
n
n
n
1.0460
1.4901
1.4903
1.5415
1.6368
1.7335
1.7383

Design Highlights
Benefits
Tubular forged body
No pressure retaining weldseams
Seats faced with stellite
Lever rests in a separate support ring
Shut-off disc with curved journal
Optimum adjustment of the disc to the body seat
Cover can be used for dismantling

of the cover fastener
The setting of the disc can be examined before

installing the bonnet cover
No special tools are necessary for dismantling the disc

fastener
6100.1.05.14
100
DRI 26
640 AB
PD 25 / PD 40
DN 65-300
171
191
273
272
331
271
337
160
270
333
391
305
405 411
DS
382
383
380
100
140
101
6100.1.05.14
DRI 26
640 AB
PD 25 / PD 40
DN 65-300
Materials
Pos.
Component
100 Body
140 Seat ring
welded on with
4 Gasket
160
171 Stud
191 Hexagonal nut
270 Cover
271 Ring
272 Segmentring
273 Cover
305 Haltering
331 Hexagonal screw
4 Spannplatte
333
4 Retaining ring
337
4 Disc
380
welded on with
382 Hinge
4 Washer
383
4 Tension pin
391
4 Hinge pin
405
4 Guide bushing
411
1.0460 (21)
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.6368 (46)
1.4903 (63)
1.4901 (66)
1.0460
1.0460
Stellite
Graphite
A 193 B7
A 194 2H
1.7383
1.7383
1.7383
1.0460
1.7383
A4
1.4903
1.4301
1.7383
Stellite
1.7383
1.4923
1.4310
1.4923
5.3106
1.5415
1.5415
Stellite
Graphite
A 193 B7
A 194 2H
1.7383
1.7383
1.7383
1.0460
1.7383
A4
1.4903
1.4301
1.7383
Stellite
1.7383
1.4923
1.4310
1.4923
5.3106
1.7335
1.7335
Stellite
Graphite
A 193 B7
A 194 2H
1.7383
1.7383
1.7383
1.0460
1.7383
A4
1.4903
1.4301
1.7383
Stellite
1.7383
1.4923
1.4310
1.4923
5.3106
1.7383
1.7383
Stellite
Graphite
A 193 B7
A 194 2H
1.7383
1.7383
1.7383
1.0460
1.7383
A4
1.4903
1.4301
1.7383
Stellite
1.7383
1.4923
1.4310
1.4923
5.3106
1.6368
1.6368
Stellite
Graphite
A 193 B7
A 194 2H
1.4903
1.4903
1.4903
1.0460
1.7383
A4
1.4903
1.4301
1.4903
Stellite
1.7383
1.4923
1.4310
1.4923
5.3106
1.4903
1.4903
Stellite
Graphite
A 193 B7
A 194 2H
1.4903
1.4903
1.4903
1.0460
1.4903
A4
1.4903
1.4301
1.4903
Stellite
1.4903
1.4923
1.4310
1.4923
5.3106
1.4901
1.4901
Stellite
Graphite
A 193 B7
A 194 2H
1.4901
1.4901
1.4901
1.0460
1.4903
A4
1.4903
1.4301
1.4901
Stellite
1.4903
1.4923
1.4310
1.4923
5.3106
4 Spare parts
Dimensions/mm and Weights/kg

DRI 26.25
DN
DS
80
100
125
150
200
250
300
70
90
111
136
178
222
263
305
406
483
559
711
864
991
230
257
317
357
445
530
603
kg
49
83
137
265
401
744
1182

DRI 26.40
DN
DS
65
80
100
125
150
200
250
50
57
72
90
111
146
185
330
368
457
533
609
762
1270
231
246
278
337
431
479
587
kg
59
91
150
288
445
796
1542
6100.1.05.14
102
DRI 16-63
640 AB
PD 16-63
DN 50-600
ASME
version
available
BW-
Version
Material PD 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650
1.0460 16 160 160 151 132 118 99 80 76 73 69 65 61 54 45 37
25 250 250 235 206 184 155 125 119 113 107 102 96 85 71 58
32 320 320 302 264 236 198 160 153 145 138 130 123 109 91 75
40 400 400 377 330 295 248 200 191 182 172 163 153 136 113 93

1.5415 16 192 192 179 165 141 137 132 131 130 129 128 127 126 125 124 109 85 64 51 41
25 300 300 280 258 221 213 206 205 203 202 200 199 197 196 194 170 132 101 79 64
32 385 385 358 330 283 273 264 262 260 258 256 255 253 251 249 217 170 129 102 81
40 480 480 448 413 354 342 330 328 325 323 321 318 316 314 311 272 212 161 127 102

1.7335 16 192 192 192 189 174 165 156 154 152 150 148 146 145 144 143 142 129 109 86 70 57 44 36 29
25 300 300 300 294 272 258 243 240 237 234 231 228 227 225 224 222 202 170 134 109 88 69 57 46
32 385 385 385 377 349 330 311 307 304 300 296 292 290 289 287 285 258 217 172 140 113 88 72 59
40 481 481 481 471 436 413 389 384 380 375 370 365 363 364 358 356 323 272 215 175 141 110 91 74

1.7383 16 192 192 192 192 189 174 165 163 161 159 157 156 154 152 150 143 127 111 97 85 74 64 55 48 41 36 32
25 300 300 300 300 294 272 258 255 252 249 246 243 240 237 234 224 199 174 152 132 115 100 85 75 65 56 49
32 384 384 384 384 377 349 330 326 322 319 315 311 307 304 300 287 255 223 194 170 147 128 109 96 83 72 63
40 480 480 480 480 471 436 413 408 403 398 384 389 384 379 375 358 318 278 243 212 184 160 137 120 104 90 79

1.6368 16 263 263 263 263 263 263 263 263 263 263 257 231 198 165 131 98 65
25 410 410 410 410 410 410 410 410 410 410 402 360 309 257 205 153 102
32 525 525 525 525 525 525 525 525 525 525 515 482 396 330 262 196 130
40 657 657 657 627 657 657 657 657 657 657 643 577 495 412 328 245 163

1.4903 16 272 272 272 272 272 272 272 272 272 272 272 272 272 272 268 245 239 221 203 186 169 153 137 123 108 96 85 74 64 55 48 41
25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 418 383 372 344 316 290 263 238 213 191 169 150 132 115 100 85 75 65
32 544 544 544 544 544 544 544 544 544 544 544 544 544 544 536 490 477 441 405 371 338 305 273 245 217 192 170 147 128 109 96 83
40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 669 613 596 552 507 464 422 382 342 306 271 240 212 184 160 137 120 104
1.4901

16
25
32
40
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
271
423
542
677
254
397
508
635
237
370
474
592
221
345
442
552
205
320
410
512
190
297
380
475
176
275
352
440
161
252
323
404
147
230
295
369
133
208
267
334
119
186
239
298
106
166
212
265
94
147
188
235
81
127
163
204
70
110
141
176
61
95
122
152
52
82
105
131
103
6100.1.05.14
DRI 16-63
Standard features
n
n
n
n
n

Swing check valve with internal hinge pin
Welded seat ring

n
n
n
640 AB
PD 16-63
DN 50-600
Media

Higher ratings on request
Materials
n
n
n
n
n
n
n
1.0460
1.4901
1.4903
1.5415
1.6368
1.7335
1.7383
Design Highlights
Benefits
Seats faced with stellite
Shut-off device with curved journal
The setting of the disc can be examined before

installing the bonnet cover
6100.1.05.14
104
DRI 16-63
640 AB
PD 16-63
DN 50-600
801
171
191
210
272
271
160
270
H
325
305
405 411
391
196
382
408
DS
383
380
100
105
6100.1.05.14
DRI 16-63
640 AB
PD 16-63
DN 50-600
Materials
Pos. Component

100 Body
4 Gasket
160
171 Stud
191 Hexagonal nut
4 Tension pin
196
210 Bonnet
270 Cover
271 Ring
272 Segmentring
4 Supportring
305
325 Headcap screw
4 Disc
380
welded on with
4 Hinge
382
4 Washer
383
4 Tension pin
391
4 Hinge pin
405
4 Tension pin
408
4 Guide bushing
411
1.0460 (21)
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.6368 (46)
1.4903 (63)
1.4901 (66)
1.0460
Graphite
1.7709
1.7218
1.4310
1.7383
1.0460
1.0460
1.0460
1.0460
A4
1.0460
Stellite
1.0460
1.0460
1.4310
1.4923
1.4310
5.3106
1.0401
1.5415
Graphite
1.7709
1.7218
1.4310
1.7383
1.5415
1.5415
1.5415
1.5415
A4
1.5415
Stellite
1.5415
1.0460
1.4310
1.4923
1.4310
5.3106
1.0401
1.7335
Graphite
1.7709
1.7218
1.4310
1.7383
1.7335
1.7335
1.7335
1.7335
A4
1.7335
Stellite
1.7335
1.7335
1.4310
1.4923
1.4310
5.3106
1.0401
1.7383
Graphite
1.7709
1.7218
1.4310
1.7383
1.7383
1.7383
1.7383
1.7383
A4
1.7383
Stellite
1.7383
1.7383
1.4310
1.4923
1.4310
5.3106
1.0401
1.6368
Graphite
1.7709
1.7218
1.4310
1.7383
1.6368
1.6368
1.6368
1.7383
A4
1.6368
Stellite
1.7383
1.6368
1.4310
1.4923
1.4310
5.3106
1.0401
1.4903
Graphite
1.7709
1.7218
1.4310
1.7383
1.4903
1.4903
1.4903
1.4903
A4
1.4903
Stellite
1.4903
1.4923
1.4310
1.4923
1.4310
5.3106
1.0401
1.4901
Graphite
1.4923
1.4923
1.4310
1.4903
1.4901
1.4901
1.4901
1.4901
A4
1.4901
Stellite
1.4903
1.4923
1.4310
1.4923
1.4310
5.3106
1.0401
4 Spare parts

DN
DS
DRI 16
L
H
kg
DRI 25
L
H
kg
DRI 32 DRI 40
H
kg
H
kg
DRI 63
65-200
Version DRI 26.40
Version DRI 26.40
225
202,5 1050
450
910
250 / 225 202,5 1150
450
250
225,0
Version DRI 26.25
Version DRI 26.25 1150
515 1300
On request
On request
300 / 250 225,0 1350
515
300
270,0 1350
605 2300
350 / 300 270,0 1550
605

350
315,0 1200
540 2300 1550
580 2300 1550
785 4000
400 / 350 315,0 1200
540 1750
580 1750
785
400
360,0 1350
600 3600 1750
660 3600
450 / 400 360,0 1350
600 1950
660 On request
450
405,0 1500
690 5400 1950
750 5400
500 / 450 405,0 1500
692 2150
750
500
450,0 1650
600 / 500 540,0 1650
On request
600
540,0 On request
6100.1.05.14
106
High pressure stop check valve
DRA 26
640 ST
PD 25 / 40
DN 80-200
ASME
version
available
BW-
Version
Material PD

20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650

1.0460 25 250 250 250 250 250 235 206 184 155 125 119 113 107 102 96 85 71 58

1.5415 25 300 300 300 300 300 280 258 221 213 206 205 203 202 200 199 197 196 194 170 132 101 79 64

1.7335 25 300 300 300 300 300 300 294 272 258 243 240 237 234 231 228 227 225 224 222 202 170 134 109 88 69 57 46

1.7383 25 300 300 300 300 300 300 300 294 272 258 255 252 249 246 243 240 237 234 224 199 174 152 132 115 100 85 75 65 56 49

1.6368 25 410 410 410 410 410 410 410 410 410 410 410 410 410 402 360 309 257 205 153 102

1.4903 25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 418 383 372 344 316 290 263 238 213 191 169 150 132 115 100 85 75 64
1.4901 25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 423 397 370 345 320 297 275 252 230 208 186 166 147 127 110 95 82

BW-
Version
Material PD

20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650

1.0460 40 400 400 400 400 400 377 330 295 248 200 190 181 172 162 153 135 113 93

1.5415 40 480 480 480 480 480 447 412 353 341 330 327 325 322 320 318 315 313 311 271 212 161 127 101

1.7335 40 481 481 481 481 481 481 471 436 412 388 384 379 374 370 365 363 360 358 355 322 271 215 175 141 110 90 73

1.7383 40 480 480 480 480 480 480 480 471 436 412 407 403 398 393 388 384 379 374 358 318 278 242 212 183 160 136 120 103 89 79

1.6368 40 657 657 657 657 657 657 657 657 657 657 657 657 657 643 577 495 412 328 245 163

1.4903 40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 669 612 596 551 506 464 421 381 341 306 271 240 212 183 160 136 120 103
1.4901 40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 677 635 592 552 512 475 440 404 369 334 298 265 235 204 176 152 131

107
6100.1.05.14
DRA 26
640 ST
PD 25 / 40
Standard features
DN 80-200
Body hollow-forged in a closed die

Double-sided high-pressure shut-off system
- Function of a check valve
- Function of a gate valve
n Internal hinge pin, pivoted in a
separate retaining ring
n Movable shut-off system guided in a groove
n Defined stop of the check disc
n Pressure sealing bonnet acc. to VGB-guidelines
n Generally stellited seats
n
n

n Temperature rating up to 650 C
n
Materials
1.0460 n 1.5415
n 1.6368 n 1.4903
n
n
n
1.7335
1.4901
1.7383
Further materials and nominal sizes on request

Media
chemical industries
Design-Highlights

n Operating mode as a check valve and a gate valve
Benefits
Possible savings:
- One valve
- Two welding seams in pipeline
- Space and weights
- Less insulation time and effort
- Less maintenance and inspection equirements
n Secure protection of relevant and complex parts
of the plant
n Better flow characteristics than non-return valves
n Minimizing pressure drop
n Better smoothness of running and adjustment of the
valves in the body seats
n Prevention of positional deviations of the shut-off disc
and protection against damage
n Effective adjustment to the body seats with constant
repetitive contact
n
Sealing in both flow directions
Full straight seat passage

Full opening angle of the check disk
n Flexible-mounted non-return and shut-off disc
n
n
Shut-off system guided in a groove
Shut-off discs with anti-twist safeguard
6100.1.05.14
108
Swing check valves
640 DJ
PN 40-250
DN 50-800
Standard features
Die-forged valve body,
cast or as a welded steel design
n Available with flange and butt weld ends
n Bolted or pressure sealing bonnet
n Pneumatic or hydraulic actuator
for safe closing
n

n
n

Materials
1.0619+N n 1.0425 n 1.5415

Standard features: Die-forged valve body
1.7335
1.7383
Media
Depending on the material the Freerun swing check
valves are suitable for water, gas, oil and other non
aggressive media

Mainly in steam cycles for fast closing /
protection applications
Design Highlights
Benefits
Seats are welded on
Shut-off device with convey pin within lever
Freewheeling hinge pin
Low friction and less packing wear
Part turn actuator for safe closing
Safe and fast closing
Standard connection to ISO 5211
Symmetric body design
109
6100.1.05.14
Easy installation of pneumatic or hydraulic

part turn actuator
Actuators can be installed on the left or on the
right side without using new components
Swing check valves
Swing check valve variants
Swing check valve with lever and weight
Swing check valve with recuperating spring
6100.1.05.14
110
High pressure line blind valve
DPV 10
990 VW
PD 10
DN 350-700
ASME
version
available
BW-
Version
Material PD 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650
1.0425 10 100 100 94 82 74 62 50 48 45 43 41 38 34 28 23

1.5415 10 120 120 112 103 88 85 82 82 81 81 80 79 79 78 78 68 53 40 32 25

1.7335 10 120 120 120 118 109 103 97 96 95 94 92 91 91 90 89 89 81 68 54 44 35 28 23 18

1.7383 10 120 120 120 120 118 109 103 102 101 99 98 97 96 95 94 89 79 69 61 53 46 40 34 30 26 22 20
1.4903 10 136 136 136 136 136 136 136 136 136 136 136 136 136 136 134 122 119 110 101 93 84 76 68 61 54 48 42 37 32 27 24 21

111
6100.1.05.14
DPV 10
990 VW
Standard features
n
n
n
Welded seat ring

Position indicator
PD 10
DN 350-700
Media
Depending on the material line blind valves are suitable

n
n


chemical industries
Materials
1.0425
1.4903
n 1.5415
n 1.7335
n 1.7383

n
n
Design Highlights
n
Thin wallthickness
Position indicator

n
Benefits
Less temperature stresses

n Indicates if seal plate is mounted or dismantled

n Best possible sealing function

n
6100.1.05.14
112
DPV 10
990 VW
PD 10
DN 350-700
191
171
171
273
273
272
272
711
711
271
271
160
160
270
270
326
326
346
346
337
337
336
336
344
344
316
316
340
340
140
140
100
100
191
Closed passage (seal plate mounted)
Free passage (seal plate dismantled)
Special design with blow-out

attachment or guide-insert on request
113
6100.1.05.14
DPV 10
990 VW
PD 10
DN 350-700
Materials
Pos.
Component
100 Body
140 Seat ring
welded on with
4 Gasket
160
171 Stud
191 Hexagonal nut
270 Cover
271 Ring
272 Segmentring
273 Cover
316 Cone plate
326 Tension pin
336 Yoke sleeve
340 Plate
337 Locking ring
344 Stud bolt
4 O-Ring
346
711 Bolt
1.0425 (22)
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.4903 (63)
1.0425
1.0460
Stellite
Graphite
1.7709
1.7218
1.7383
1.7383
1.7383
1.0460
1.7383
1.4021
CW 713 R
1.7383
Spring Steel
1.4021
Viton
8.8
1.5415
1.5415
Stellite
Graphite
1.7709
1.7218
1.7383
1.7383
1.7383
1.0460
1.7383
1.4021
CW 713 R
1.7383
Spring Steel
1.4021
Viton
8.8
1.7335
1.7335
Stellite
Graphite
1.7709
1.7218
1.7383
1.7383
1.7383
1.0460
1.7383
1.4021
CW 713 R
1.7383
Spring Steel
1.4021
Viton
8.8
1.7383
1.7383
Stellite
Graphite
1.7709
1.7218
1.7383
1.7383
1.7383
1.0460
1.7383
1.4021
CW 713 R
1.7383
Spring Steel
1.4021
Viton
8.8
1.4903
1.4903
Stellite
Graphite
1.7709
1.7218
1.4903
1.4903
1.4903
1.0460
1.4903
1.4021
CW 713 R
1.7383
Spring Steel
1.4021
Viton
8.8
4 Spare parts

DN
DS
350
400
450
500
600
700
330
375
419
464
559
640
850
950
1050
1150
1350
1550
645
690
710
861
945
1150
kg
710
1150
1400
1800
2540
3750
6100.1.05.14
114
DPV 16-63
990 VW
PD 16-63
DN 65-600
ASME
version
available
BW-
Version
Material PD 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650
1.0460 16 160 160 151 132 118 99 80 76 73 69 65 61 54 45 37
25 250 250 235 206 184 155 125 119 113 107 102 96 85 71 58
32 320 320 302 264 236 198 160 153 145 138 130 123 109 91 75
40 400 400 377 330 295 248 200 191 182 172 163 153 136 113 93

1.5415 16 192 192 179 165 141 137 132 131 130 129 128 127 126 125 124 109 85 64 51 41
25 300 300 280 258 221 213 206 205 203 202 200 199 197 196 194 170 132 101 79 64
32 385 385 358 330 283 273 264 262 260 258 256 255 253 251 249 217 170 129 102 81
40 480 480 448 413 354 342 330 328 325 323 321 318 316 314 311 272 212 161 127 102

1.7335 16 192 192 192 189 174 165 156 154 152 150 148 146 145 144 143 142 129 109 86 70 57 44 36 29
25 300 300 300 294 272 258 243 240 237 234 231 228 227 225 224 222 202 170 134 109 88 69 57 46
32 385 385 385 377 349 330 311 307 304 300 296 292 290 289 287 285 258 217 172 140 113 88 72 59
40 481 481 481 471 436 413 389 384 380 375 370 365 363 364 358 356 323 272 215 175 141 110 91 74

1.7383 16 192 192 192 192 189 174 165 163 161 159 157 156 154 152 150 143 127 111 97 85 74 64 55 48 41 36 32
25 300 300 300 300 294 272 258 255 252 249 246 243 240 237 234 224 199 174 152 132 115 100 85 75 65 56 49
32 384 384 384 384 377 349 330 326 322 319 315 311 307 304 300 287 255 223 194 170 147 128 109 96 83 72 63
40 480 480 480 480 471 436 413 408 403 398 384 389 384 379 375 358 318 278 243 212 184 160 137 120 104 90 79

1.6368 16 263 263 263 263 263 263 263 263 263 263 257 231 198 165 131 98 65
25 410 410 410 410 410 410 410 410 410 410 402 360 309 257 205 153 102
32 525 525 525 525 525 525 525 525 525 525 515 482 396 330 262 196 130
40 657 657 657 627 657 657 657 657 657 657 643 577 495 412 328 245 163

1.4903 16 272 272 272 272 272 272 272 272 272 272 272 272 272 272 268 245 239 221 203 186 169 153 137 123 108 96 85 74 64 55 48 41
25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 418 383 372 344 316 290 263 238 213 191 169 150 132 115 100 85 75 65
32 544 544 544 544 544 544 544 544 544 544 544 544 544 544 536 490 477 441 405 371 338 305 273 245 217 192 170 147 128 109 96 83
40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 669 613 596 552 507 464 422 382 342 306 271 240 212 184 160 137 120 104
1.4901

16
25
32
40
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
271
423
542
677
254
397
508
635
237
370
474
592
221
345
442
552
205
320
410
512
190
297
380
475
176
275
352
440
161
252
323
404
147
230
295
369
133
208
267
334
119
186
239
298
106
166
212
265
94
147
188
235
81
127
163
204
70
110
141
176
61
95
122
152
52
82
105
131
115
6100.1.05.14
DPV 16-63
Standard features
n

n
n

with welded seat rings
Position indicator

n
n

990 VW
PD 16-63
DN 65-600
Media
Depending on the material line blind valves are suitable


Materials
1.0460
1.4901
n 1.4903
n 1.5415
n 1.6368
n 1.7335
n 1.7383

n
n
Design Highlights
n
Valve body and cover made of forged steel
Position indicator


n Cover can be used for dismantling of the
cover fastener
n
Benefits

n Indicates if seal plate is mounted or dismantled

n Best possible sealing function

n No special tools are necessary for dismantling

n
6100.1.05.14
116
DPV 16-63
990 VW
PD 16-63
DN 65-600
171
191
191
273
273
272
272
271
271
160
160
270
270
326
326
336
336
316
316
340
340
140
140
100
100
346
346
171
Closed passage (seal plate mounted)
Free passage
With blow-out attachment
(seal plate dismantled)
(seal plate mounted)
Special design with blow-out

attachment or guide-insert on request
117
6100.1.05.14
DPV 16-63
990 VW
PD 16-63
DN 65-600
Materials
Pos.
Component
100 Body
140 Seat ring
welded on with
4 Gasket
160
171 Tension screw
191 Hexagonal nut
270 Cover
271 Ring
272 Segmentring
273 Cover
316 Cone plate
326 Tension pin
336 Yoke sleeve
340 Plate
4 O-Ring
346
1.0460 (21)
1.5415 (42)
1.7335 (44)
1.7383 (45)
1.6368 (46)
1.4903 (63)
1.4901 (66)
1.0460
1.0460
Stellite
Graphite
A 193 B7
A 194 2H
1.7383
1.7383
1.7383
1.0460
1.7383
1.4021
CW 713 R
1.7383
Viton
1.5415
1.5415
Stellite
Graphite
A 193 B7
A 194 2H
1.7383
1.7383
1.7383
1.0460
1.7383
1.4021
CW 713 R
1.7383
Viton
1.7335
1.7335
Stellite
Graphite
A 193 B7
A 194 2H
1.7383
1.7383
1.7383
1.0460
1.7383
1.4021
CW 713 R
1.7383
Viton
1.7383
1.7383
Stellite
Graphite
A 193 B7
A 194 2H
1.7383
1.7383
1.7383
1.0460
1.7383
1.4021
CW 713 R
1.7383
Viton
1.6368
1.6368
Stellite
Graphite
A 193 B7
A 194 2H
1.4903
1.4903
1.4903
1.0460
1.4903
1.4021
CW 713 R
1.7383
Viton
1.4903
1.4903
Stellite
Graphite
A 193 B7
A 194 2H
1.4903
1.4903
1.4903
1.0460
1.4903
1.4021
CW 713 R
1.7383
Viton
1.4901
1.4901
Stellite
Graphite
A 193 B7
A 194 2H
1.4901
1.4901
1.4901
1.0460
1.4901
1.4021
CW 713 R
1.7383
Viton
4 Spare parts

DPV 16
DPV 25
DPV 32 DPV 40
DN
L
H
kg
L
H
kg
L
H
kg
L
H
kg

65
330
208
59,0 330
231
59
80
305
207
49
305
207
49
368
221
91,0 368
246
91
100
406
231
83
406
231
83
457
250 150,0 457
278
150
125
483
285
137
483
285
137
533
303 288,0 533
337
288
150
559
321
265
559
321
265
609
388 445,0 609
431
445
200
711
401
401
711
401
401
762
431 796,0 762
479
796
250
864
477
744
864
477
744 1270
528 1542,0 1270
587 1542
300
991
543 1182
991
543 1182
350
400
On request On request On request On request
450
500
600
DPV 63
On request
6100.1.05.14
118
Strainer
Strainer
990 ST
PN 500
DN 10-65
ASME
version
available
Material
PN -10 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650
1.0460

1.5415
500 550 550 550 550 550 550 518 463 389 315 300 285 270 255 240 213 177 146
500 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 537,4 518,8 514,7 510,9 507,3 503,8 500,3 496,7 493,1 489,3 426,9 333,5 253,5 200,1 160,1
1.7335
500 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 500,0 426,9 338,0 275,7 222,4 173,4 142,0 116,0
1.7383
500 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 500,3 437,3 381,7 333,5 289,1 252,0 214,9 189,0 163,1 140,8 124,5
1.4903
500 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 550,0 500,0 465,0 430,0 380,0 338,0 298,0 261,0 231,0 198,0 172,0
1.4901
500 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 550 526 470 419 370 322 278 241 207
1.4550
500 550 550 550 550 550 550 544 504 481 463 460 456 454 451 449 447 445 443 442 441 440 439 438 437 437 436 435 434 433 396 363 320 271 240 207
1) Operating temperature = design temperature minus temperature surcharge acc. to DIN regulations
119
6100.1.05.14
Strainer
Strainer
990 ST
PN 500
DN 10-65
Media
Standard features
n
n
n
n

Screw cap
Compact design
Also available in angle pattern (992 ST)
Depending on the material the strainer is suitable for

Chemical industries, power plants, process engineering

and other

n Maximum pressure difference
between inlet and outlet 2 bar
n
n
Materials
n
n
n
n
n
n
n
Screen/filter mesh size
1.0460
0,10
1.4550
0,25
1.4901
0,50
1.4903
1,00
1.5415
1.7335
1.7383
mm
mm
mm
mm
Further materials and strainer mesh on request
Design Highlights
Benefits
In contrast to cast steel parts generally free from
porosity and shrink holes
Body and bonnet in forged steel
Body in two separate pieces with bolted connection
Differences of screen/filter mesh size
Improved the service possibilities,

for exchanging the screen filter
Blow out protection
Individually selectable according to the grade

of pollution and medium
6100.1.05.14
120
Strainer
Strainer
990 ST
PN 500
DN 10-65
Flow direction
320
100
170
160
321
210
190
121
6100.1.05.14
Strainer
Strainer
990 ST
PN 500
DN 10-65
Materials
Pos. Component
1.0460 (21)
1.5415 (42)
1.7335 (44)
1.7383 (45)

100 Body
1.0460
1.5415
1.7335
1.7383
4 Dichtung
Graphite
Graphite
Graphite
Graphite
160
170 Stud
1.4923
1.4923
1.4923
1.4923
190 Hexagonal nut
1.4923
1.4923
1.4923
1.4923
210 Bonnet
1.7383
1.7383
1.7383
1.7383
4 Filter cylinder
1.4571
1.4571
1.4571
1.4571
320
4 Packing
Graphite
Graphite
Graphite
Graphite
321

1.4903 (63)
1.4901 (66)
1.4550 (89)
1.4903
Graphite
1.4986
1.4986
1.4903
1.4571
Graphite
1.4901
Graphite
1.4986
1.4986
1.4901
1.4571
Graphite
1.4550
Graphite
1.4986
1.4986
1.4550
1.4571
Graphite
4 Spare parts
Dimensions/mm

DN
10
15
20
25
321)
40
50
65
150
150
180
180
300
300
300
350
100
100
127
127
198
198
198
251
Weights/kg

DN
BW
10
15
20
25
321)
40
50
65
3,7
3,7
7,6
7,4
29,8
29,3
28,8
65,0
1) DN 32 not included in DIN-Standard

Attention: In case of welding connections the permissible operating
overpressure is valid for the corresponding tube dimensions.
6100.1.05.14
122
Strainer
Strainer DSF
990 ST
PD 25 / 40
DN 80-250
ASME
version
available
BW-
Version
Material PD

20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650

1.0460 25 250 250 250 250 250 235 206 184 155 125 119 113 107 102 96 85 71 58

1.5415 25 300 300 300 300 300 280 258 221 213 206 205 203 202 200 199 197 196 194 170 132 101 79 64

1.7335 25 300 300 300 300 300 300 294 272 258 243 240 237 234 231 228 227 225 224 222 202 170 134 109 88 69 57 46

1.7383 25 300 300 300 300 300 300 300 294 272 258 255 252 249 246 243 240 237 234 224 199 174 152 132 115 100 85 75 65 56 49

1.6368 25 410 410 410 410 410 410 410 410 410 410 410 410 410 402 360 309 257 205 153 102

1.4903 25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 418 383 372 344 316 290 263 238 213 191 169 150 132 115 100 85 75 64
1.4901 25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 425 423 397 370 345 320 297 275 252 230 208 186 166 147 127 110 95 82

BW-
Version
Material PD

20 50 100 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650

1.0460 40 400 400 400 400 400 377 330 295 248 200 190 181 172 162 153 135 113 93

1.5415 40 480 480 480 480 480 447 412 353 341 330 327 325 322 320 318 315 313 311 271 212 161 127 101

1.7335 40 481 481 481 481 481 481 471 436 412 388 384 379 374 370 365 363 360 358 355 322 271 215 175 141 110 90 73

1.7383 40 480 480 480 480 480 480 480 471 436 412 407 403 398 393 388 384 379 374 358 318 278 242 212 183 160 136 120 103 89 79

1.6368 40 657 657 657 657 657 657 657 657 657 657 657 657 657 643 577 495 412 328 245 163

1.4903 40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 669 612 596 551 506 464 421 381 341 306 271 240 212 183 160 136 120 103
1.4901 40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 680 677 635 592 552 512 475 440 404 369 334 298 265 235 204 176 152 131

123
6100.1.05.14
Strainer
Strainer DSF
990 ST
PD 25 / 40
DN 80-250
Media
Standard features
n

Depending on the material the strainer is suitable for


n Maximum pressure difference
between inlet and outlet 2 bar
Chemical industries, power plants, process engineering

and other
n
n
Materials
n
n
n
n
n
n
n
Screen/filter mesh size
1.0460
0,10
1.4901
0,25
1.4903
0,50
1.5415
1,00
1.6368
3,00
1.7335
1.7383
mm
mm
mm
mm
mm
Further materials and strainer mesh on request

Design Highlights
Benefits
In contrast to cast steel parts generally
free from porosity and shrink holes
Body and bonnet in forged steel
Differences of screen/filter mesh size
Cover with draining possibility
Ease removal filter residues
Individually selectable according to the grade

of pollution and medium
6100.1.05.14
124
Technical appendix
Pressure-rate tables PD 10-63
PERSTA pressure ratings (PD) have been developed

close to the standardized PN 100-630 pressure ratings
and apply to valves with accordingly designed butt weld
ends only. Valves with standard flanges are always
marked with the corresponding pressure ratings and
can be used within these limits only. The figures refer
to all pressure retaining components including the
obturators.
design of the operating elements such as the handwheel

and actuators or gear-boxes.
Differential pressure and operation

PERSTA gate valves can be operated with a differential
pressure up to 50 % of the design pressures given in
table 8.1. Always check with PERSTA first if they are to
be used with higher differential pressures. The operating
conditions (as specified by the customer) determine the
Attention:
The wall thickness for butt weld ends may vary for
different piping materials and must be checked
carefully for every application.
Notice:
The maximum differential pressures to which gate
valves with bodies made of 1.4901, 1.4903 and
1.6368 can be operated have to be always obtained
from PERSTA.
The valves will be marked as working pressure valves.
PERSTA - pressure ratings (PD) for butt weld valves

Material PD 120 150 200 250 300 350 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650
1.0460
10 100 100 94 82 74 62 50 48 45 43 41 38 34 28 23

16 160 160 151 132 118 99 80 76 73 69 65 61 54 45 37

25 250 250 235 206 184 155 125 119 113 107 102 96 85 71 58

32 320 320 302 264 236 198 160 153 145 138 130 123 109 91 75

40 400 400 377 330 295 248 200 191 182 172 163 153 136 113 93

1.5415
10 120 120 112 103 88 85 82 82 81 81 80 79 79 78 78 68 53 40 32 25

16 192 192 179 165 141 137 132 131 130 129 128 127 126 125 124 109 85 64 51 41

25 300 300 280 258 221 213 206 205 203 202 200 199 197 196 194 170 132 101 79 64

32 385 385 358 330 283 273 264 262 260 258 256 255 253 251 249 217 170 129 102 81

40 480 480 448 413 354 342 330 328 325 323 321 318 316 314 311 272 212 161 127 102

1.7335
10 120 120 120 118 109 103 97 96 95 94 92 91 91 90 89 89 81 68 54 44 35 28 23 18

16 192 192 192 189 174 165 156 154 152 150 148 146 145 144 143 142 129 109 86 70 57 44 36 29

25 300 300 300 294 272 258 243 240 237 234 231 228 227 225 224 222 202 170 134 109 88 69 57 46

32 385 385 385 377 349 330 311 307 304 300 296 292 290 289 287 285 258 217 172 140 113 88 72 59

40 481 481 481 471 436 413 389 384 380 375 370 365 363 364 358 356 323 272 215 175 141 110 91 74

1.7383
10 120 120 120 120 118 109 103 102 101 99 98 97 96 95 94 89 79 69 61 53 46 40 34 30 26 22 20

16 192 192 192 192 189 174 165 163 161 159 157 156 154 152 150 143 127 111 97 85 74 64 55 48 41 36 32

25 300 300 300 300 294 272 258 255 252 249 246 243 240 237 234 224 199 174 152 132 115 100 85 75 65 56 49

32 384 384 384 384 377 349 330 326 322 319 315 311 307 304 300 287 255 223 194 170 147 128 109 96 83 72 63

40 480 480 480 480 471 436 413 408 403 398 384 389 384 379 375 358 318 278 243 212 184 160 137 120 104 90 79

1.6368
16 263 263 263 263 263 263 263 263 263 263 257 231 198 165 131 98 65

25 410 410 410 410 410 410 410 410 410 410 402 360 309 257 205 153 102

32 525 525 525 525 525 525 525 525 525 525 515 482 396 330 262 196 130

40 657 657 657 627 657 657 657 657 657 657 643 577 495 412 328 245 163

1.4903
16 272 272 272 272 272 272 272 272 272 272 272 272 272 272 268 245 239 221 203 186 169 153 137 123 108 96 85 74 64 55 48 41

25 425 425 425 425 425 425 425 425 425 425 425 425 425 425 418 383 372 344 316 290 263 238 213 191 169 150 132 115 100 85 75 65

32 544 544 544 544 544 544 544 544 544 544 544 544 544 544 536 490 477 441 405 371 338 305 273 245 217 192 170 147 128 109 96 83

40 680 680 680 680 680 680 680 680 680 680 680 680 680 680 669 613 596 552 507 464 422 382 342 306 271 240 212 184 160 137 120 104
1.4901

16
25
32
40
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
272
425
544
680
271
423
542
677
125
6100.1.05.14
254
397
508
635
237
370
474
592
221
345
442
552
205
320
410
512
190
297
380
475
176
275
352
440
161
252
323
404
147
230
295
369
133
208
267
334
119
186
239
298
106 94 81 70 61 52
166 147 127 110 95 82
212 188 163 141 122 105
265 235 204 176 152 131
* Design according to working data
Technical appendix
Flange dimensions
d2
d4
DS
K
D
Raised face to DIN 2526 resp. EN 1092 (other flange-types possible)
Flange dimensions
Nom.-
DN 15 20 25 32 40 50 65 80
press Dimaensions

10
Flange D
95 105 115 140 150 165 185 200

b
16 18 18 18 18 20 22 24

k
65 75 85 100 110 125 145 160
Raised face d4
45 58 68 78 88 102 122 138

f
2
2
2
2
3
3
3
3

No. of bolts
4
4
4
4
4
4 8(4)*
8

Threat M12 M12 M12 M16 M16 M16 M16 M16

d2
14 14 14 18 18 18 18 18

100 125 150 200 250 300 350 400 500 600 700 800
220 250
24 26
180 210
158 188
3 3
8 8
M16 M16
18 18
285
22
240
212
3
8
M20
22
340
24
295
268
3
8
M20
22
395
26
350
320
3
12
M20
22
445
26
400
370
4
12
M20
22
505
26
460
430
4
16
M20
22
565
26
515
482
4
16
M24
26
670
28
620
585
4
20
M24
26
780
28
725
685
5
20
M27
30
895 1015
30 32
840 950
800 905
5
5
24 24
M27 M30
30 33
16

Flange D
95 105 115 140 150 165 185 200
b
16 18 18 18 18 20 22 24
k
65 75 85 100 110 125 145 160
Raised face d4
45 58 68 78 88 102 122 138
f
2
2
2
2
3
3
3
3
No. of bolts
4
4
4
4
4
4 8(4)*
8
Threat M12 M12 M12 M16 M16 M16 M16 M16
d2 14 14 14 18 18 18 18 18
220 250
24 26
180 210
158 188
3 3
8 8
M16 M16
18 18
285
22
240
212
3
8
M20
22
340
24
295
268
3
12
M20
22
405
26
355
320
3
12
M24
26
460
28
410
378
4
12
M24
26
520
30
470
438
4
16
M24
26
580
32
525
490
4
16
M27
30
715
34
650
610
4
20
M30
33
840
36
770
725
5
20
M33
36
910 1025
36 38
840 950
795 900
5
5
24 24
M33 M36
36 39
25

Flange D
95 105 115 140 150 165 185 200
b
16 18 18 18 18 20 22 24
k
65 75 85 100 110 125 145 160
Raised face d4
45 58 68 78 88 102 122 138
f
2
2
2
2
3
3
3
3
No. of bolts
4
4
4
4
4
4 8(4)*
8
Threat M12 M12 M12 M16 M16 M16 M16 M16
d2
14 14 14 18 18 18 18 18
235 270
24 26
190 220
162 188
3 3
8 8
M20 M24
22 26
300
28
250
218
3
8
M24
26
360
30
310
278
3
12
M24
26
425
32
370
335
3
12
M27
30
485
34
430
395
4
16
M27
30
555
38
490
450
4
16
M30
33
620
40
550
505
4
16
M33
36
730
44
660
615
4
20
M33
36
845
46
770
720
5
20
M36
39
960 1085
46 50
875 990
820 930
5
5
24 24
M39 M45
42 48
40

Flange D
95 105 115 140 150 165 185
b
16 18 18 18 18 20 22
k
65 75 85 100 110 125 145
Raised face d4
45 58 68 78 88 102 122
f
2
2
2
2
3
3
3
No. of bolts
4
4
4
4
4
4
8
Threat M12 M12 M12 M16 M16 M16 M16
d2
14 14 14 18 18 18 18
200
24
160
138
3
8
M16
18
235 270
24 26
190 220
162 188
3 3
8 8
M20 M24
22 26
300
28
250
218
3
8
M24
26
375
34
320
285
3
12
M27
30
450
38
385
345
3
12
M30
33
515
42
450
410
4
16
M30
33
580
46
510
465
4
16
M33
36
660
50
585
535
4
16
M36
39
755
52
670
615
4
20
M39
42
890
60
795
735
5
20
M45
48
995 1140
64 72
900 1030
840 960
5
5
24 24
M45 M52
48 56
63

Flange D 105 130 140 155 170 180 205 215

b
20 24 24 24 26 26 26 28
k
75 90 100 110 125 135 160 170
Raised face d4
45 60 68 78 88 102 122 138
f
2
2
2
2
3
3
3
3
No. of bolts
4
4
4
4
4
4
8
8
Threat M12 M16 M16 M20 M20 M20 M20 M20
d2
14 18 18 22 22 22 22 22
250 295
30 34
200 240
162 188
3 3
8 8
M24 M27
26 30
345
36
280
218
3
8
M30
33
415
42
345
285
3
12
M33
36
470
46
400
345
3
12
M33
36
530
52
460
410
4
16
M33
36
100

Flange D 105 130 140 155 170 195 220 230

b
20 24 24 24 26 28 30 32
k
75 90 100 110 125 145 170 180
Raised face d4
45 60 68 78 88 102 122 138
f
2
2
2
2
3
3
3
3
No. of bolts
4
4
4
4
4
4
8
8
Threat M12 M16 M16 M20 M20 M24 M24 M24
d2
14 18 18 22 22 26 26 26
265 315
36 40
210 250
162 188
3 3
8 8
M27 M30
30 33
355
44
290
218
3
12
M30
33
430
52
360
285
3
12
M33
36
505
60
430
345
3
12
M36
39
585
68
500
410
4
16
M39
42
160

Flange D 105 130 140 155 170 195 220 230

b
20 24 24 24 28 30 34 36
k
75 90 100 110 125 145 170 180
Raised face d4
45 60 68 78 88 102 122 138
f
2
2
2
2
3
3
3
3
No. of bolts
4
4
4
4
4
4
8
8
Threat M12 M16 M16 M20 M20 M24 M24 M24
d2
14 18 18 22 22 26 26 26
265 315
40 44
210 250
162 188
3 3
8 8
M27 M30
30 33
355
50
290
218
3
12
M30
33
430
60
360
285
3
12
M33
36
515
68
430
345
3
12
M39
42
585
* On request available for flanges acc.
78 DIN 2632 and DIN 2633.
500
410
4
16
M39
42
6100.1.05.14
126
Technical appendix
Design
Body:
As a pressure-retaining component, the body, including the
bonnet, determines the ranges in which the valves can be
used. The demand for valves to withstand higher pressure
and temperatures calls for special materials and production
processes. In high-pressure applications, pressure ratings,
nominal sizes and quantities require different production
processes which take account of different conditions of
use. Designs therefore vary according to the particular
applications.
PERSTA forged valve bodies, particularly those designed
for power stations, are die-forged or produced as opendie forgings which are then machined. Specific rolling and
forming processes give the parts and dense, uniform,
fine-structure with no bubbles or pores, and with a fibre
orientation that is ideal for their intended use.
The modern production methods have increased the use
of forged steel for high-pressure applications. However,
the development of die-forged bodies has been restricted
by the high forming forces and the associated size and
cost of the forgings. Machined open-die forgings are
therefore used for large bodies.
For PERSTA high pressure valves the following
production methods proved excellent results:
1. Hollow one-piece-forgings, mainly for valve bodies in the
DSK 26 range, 65 - 300. Connecting flanges or butt weld
ends are welded on with a circumferential seam.
2. Bodies for gate valves and swing check valves in the
DSK and DRI range, 50 - 600 are produced as solid,
open-die forgings which are then machined.
Valves are subjected to stress in the following ways:
mechanically by
n
operating pressure

n
operating temperature

n
temperature gradients during
starting up and shut down

n
erosion and cavitation by the medium

n
due to the forces exerted by the connected pipes,
fastening devices and the weight of mechanical
actuators, and
n
chemically

n
due to corrosion.
n

127
6100.1.05.14
smooth transitions between different wall thicknesses.

Gate valves are sealed on the downstream side of the
body. The required sealing force is provided by the medium
by means of the differential pressure. For pressure ratings
PD 10-63, PERSTA DSK gate valves are fitted with a
mechanical stembarel stop to limit the stress on the stems
and the sealing faces caused by the actuation forces.
Ledges or grooves are guiding the wedge or the split
wedge in the body after about 10 % of the opening lift.
The forces which have to be absorbed from the guides
are relatively low because there has already been a large
degree of pressure compensation at this point.
The weld seams are designed for easy radiographic or
ultrasonic testing.
All PERSTA gate valves and swing check valves can be
delivered with buttwelding ends to match the corresponding material and pipe diameter.
Stem sealing
The gland packing seals the stem guide onto outside.
Operational demands of this sealing arise by reason of
stem travel, pressure and friction at the gland packing, by
thermal cycle stress and by the medium. The design of the
gland follower resp. gland ring assures a smooth contact
pressure of the packing rings even in the case of an easily
irregular tightening of the gland bolts and prevents a seizing of the stem.
Mode of operation
A power applied by the stud bolts onto the gland follower
will be transmitted via the gland ring resp. chamber ring to
the packing rings. Thereby the packing rings are pressed
together. Upcoming surface pressure towards the wall of
the stuffing box chamber and towards the stem surface
tightens against the medium.
Technical appendix
Design
Operating characteristics:
An axial force which increases as the internal pressure
increases is applied to the elastic gasket. This force
compresses the elastic gasket which deforms radially
and axially. In the radial direction it is pressed against
the wall of the body and the cover, thus achieving the
required surface pressure and associated sealing force.
The ring on the gasket absorbs axial force and transfers
it to the segment ring. The segment ring is fitted in a
groove in the body, thus transferring the axial force to
the body. The segment ring consisting of four parts is
held in the groove by the centring cover. The cover is
pre-stressed by studs so that the gasket is deformed
and the sealing effect achieved even when the internal
pressure is low. Moreover the cover is centered by
means of the supporting cap.
Segmentring
Attention:
Overpressure devices are required to protect against
unacceptable pressure peaks. See page 83.
(440) Gland flange

(462) Stud
(430) Gland ring
(420) Packing
(421) Packing ring
(171) Stud
(170) Stud
(200) Bonnet
(273) Cover
(272) Segmentring
(271) Thrust ring
(160) Gasket
(270) Cover
(100) Body
6100.1.05.14
128
Technical appendix
Pipe and valve dimensions

Pipe (DIN 2448) and valve dimensions rel. DIN 3239 and DIN 2559
Butt welding ends

Line 1
Line 2
Line 3
Line 4
Line 5
Line 6
Line 7
Line 8
DN
bis PN 40
PN 63
PN 100
PN 160
PN 250
PN 320
PN 400
PN 630

10

15

20

25

40

50

65

80

100

125

150

200

250

300

350

400

500

129
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
d1
d2
dp (DIN2559)
d3
s
6100.1.05.14
20,0
20,0
20,0
20,0
20,0
20,0
20,0
24,0

18,0
18,0
18,0
18,0
18,0
18,0
18,0
22,0
13,0
13,0
13,0
13,0
12,0
12,0
10,0
11,5
17,2
17,2
17,2
17,2
17,2
17,2
17,2
21,3

2,0
2,0
2,0
2,0
2,6
2,6
3,6
5,0
24,0
24,0
24,0
24,0
24,0
24,0
31,0
37,0

22,0
22,0
22,0
22,0
22,0
22,0
28,0
34,0
17,0
17,0
17,0
17,0
16,0
15,0
17,0
18,5
21,3
21,3
21,3
21,3
21,3
21,3
26,9
33,7

2,0
2,0
2,0
2,0
2,6
3,2
5,0
8,0
31,0
28,0
22,0
26,9
2,3
37,0
37,0
37,0
37,0
39,0
39,0
48,0
54,0

34,0
34,0
34,0
34,0
35,0
35,0
44,0
49,0
28,5
28,5
28,5
27,0
26,5
24,0
29,0
25,0
33,7
33,7
33,7
33,7
33,7
33,7
42,4
48,3

2,6
2,6
2,6
3,2
3,6
5,0
7,1
12,5
54,0
54,0
54,0
54,0
54,0
54,67,0
83,0

49,0
49,0
49,0
49,0
49,0
49,0
61,0
77,0
43,0
43,0
43,0
41,0
38,5
36,0
40,0
43,5
48,3
48,3
48,3
48,3
48,3
48,3
60,3
76,1

2,6
2,6
2,6
3,6
5,0
6,3
11,0
17,5
67,0
67,0
67,0
67,0
67,0
83,0
83,0
96,0

61,0
61,0
61,0
61,0
61,0
77,0
77,0
90,0
54,0
54,0
54,0
52,5
45,0
59,5
49,5
51,5
60,3
60,3
60,3
60,3
60,3
76,1
76,1
88,9

3,2
3,2
3,2
4,0
8,0
8,8
14,2
20,0
83,0
83,0
83,0
83,0
83,0
96,0
121,0
77,0
77,0
77,0
77,0
77,0
90,0
115,0
69,0
69,0
69,0
65,0
59,5
68,0
81,0
76,1
76,1
76,1
76,1
76,1
88,9
114,3
3,6
3,6
3,6
5,6
8,8
11,0
17,5
96,0
96,0
96,0
96,0
121,0
121,0
121,0
90,0
90,0
90,0
90,0
115,0
115,0
115,0
81,0
81,0
81,0
76,5
93,0
87,5
81,0
88,9
88,9
88,9
88,9
114,3
114,3
114,3
4,0
4,0
4,0
6,3
11,0
14,2
17,5
121,0
121,0
121,0
121,0
115,0
115,0
115,0
115,0
104,0
104,0
104,0
98,5

114,3
114,3
114,3
114,3
5,0
5,0
5,0
8,0
147,0
147,0
147,0
147,0
141,0
141,0
141,0
141,0
130,5
130,5
127,0
120,5
139,7
139,7
139,7
139,7
4,5
4,5
6,3
10,0
176,0
176,0
176,0
176,0
170,0
170,0
170,0
170,0

156,5
156,5
154,0
144,5
168,3
168,3
168,3
168,3
5,6
5,6
7,1
12,5
228,0
228,0
228,0
228,0
222,0
222,0
222,0
222,0
204,5
204,5
199,5
189,0
219,1
219,1
219,1
219,1
7,1
7,1
10,0
16,0
282,0
282,0
282,0
276,0
276,0
276,0
256,5
255,0
248,5
273,0
273,0
273,0
Note:
8,0
8,8
12,5
The outer diameter values marked by colour depend on the used material
331,0
331,0
331,0
325,0
325,0
325,0
and heating diameter larger outer diameter
306,5
301,0
295,5
323,9
323,9
323,9
8,0
11,0
14,2
Pressureratings and materials acc. DIN 2401. (Wst. 1.0460; 1.0425; 1.5415; 1.7335;
365,0
365,0
365,0
1.7383) No casting materials are listed.
359,0
359,0
359,0
336,5
330,0
324,0
355,6
355,6
355,6
8,8
12,5
16,0
417,0
417,0
411,0
411,0
383,0
377,0
406,4
406,4
11,0
14,2
518,0
512,0
1) d1 is the maximal permitted scaling of the outer diameter;
478,0
generally for cast steal and weldable cast iron.
508,0
2) d3 is the outer diameter of the connected steelpipe Line 1 acc. ISO 4200-1985
14,2
Technical appendix
Pipe and valve dimensions

Pipe (DIN 2448) and valve dimensions rel. EN 12627

Butt welding ends

Line 1
Line 2
Line 3
Line 4
Line 5
Line 6
Line 7
DN
bis PN 40
PN 63
PN 100
PN 160
PN 250
PN 320
PN 400

10

15

20

25

40

50

65

80

100

125

150

200

250

300

350

400

500

A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
A
B
d3
s
Line 8
PN 630
18,0
18,0
18,0
18,0
18,0
18,0
18,0
13,2
13,2
13,2
13,2
12,0
12,0
10,0
17,2
17,2
17,2
17,2
17,2
17,2
17,2
2,0
2,0
2,0
2,0
2,6
2,6
3,6
22,0
22,0
22,0
22,0
22,0
22,0
28,0
17,3
17,3
17,3
17,3
16,1
14,9
16,9
21,3
21,3
21,3
21,3
21,3
21,3
26,9
2,0
2,0
2,0
2,0
2,6
3,2
5,0
28,0
22,3
26,9
2,3
35,0
35,0
35,0
35,0
35,0
35,0
44,0
28,5
28,5
28,5
27,3
26,5
23,7
28,2
33,7
33,7
33,7
33,7
33,7
33,7
42,4
2,6
2,6
2,6
3,2
3,6
5,0
7,1
50,0
50,0
50,0
50,0
50,0
50,0
62,0
43,1
43,1
43,1
41,1
38,3
35,7
38,3
48,3
48,3
48,3
48,3
48,3
48,3
60,3
2,6
2,6
2,6
3,6
5,0
6,3
11,0
62,0
62,0
62,0
62,0
62,0
77,0
77,0
53,9
53,9
53,9
52,3
44,3
58,5
47,7
60,3
60,3
60,3
60,3
60,3
76,1
76,1
3,2
3,2
3,2
4,0
8,0
8,8
14,2
77,0
77,0
77,0
77,0
77,0
91,0
117,0
68,9
68,9
68,9
64,9
58,5
66,9
79,3
76,1
76,1
76,1
76,1
76,1
88,9
114,3
3,6
3,6
3,6
5,6
8,8
11,0
17,5
91,0
91,0
91,0
91,0
117,0
117,0
117,0
80,9
80,9
80,9
76,3
92,3
85,9
79,3
88,9
88,9
88,9
88,9
114,3
114,3
114,3
4,0
4,0
4,0
6,3
11,0
14,2
17,5
117,0
117,0
117,0
117,0
104,3
104,3
104,3
98,3
114,3
114,3
114,3
114,3
5,0
5,0
5,0
8,0
144,0
144,0
144,0
144,0
130,7
130,7
127,1
119,7
139,7
139,7
139,7
139,7
4,5
4,5
6,3
10,0
172,0
172,0
172,0
172,0

157,1
157,1
154,1
143,3
168,3
168,3
168,3
168,3
5,6
5,6
7,1
12,5
223,0
223,0
223,0
223,0
204,9
204,9
199,1
187,1
219,1
219,1
219,1
219,1
7,1
7,1
10,0
16,0
278,0
278,0
278,0
257,0
255,4
248,0
273,0
273,0
273,0
8,0
8,8
12,5
329,0
329,0
329,0
307,9
301,9
295,5
323,9
323,9
323,9
8,0
11,0
14,2
362,0
362,0
362,0
338,0
330,6
323,6
355,6
355,6
355,6
8,8
12,5
16,0
413,0
413,0
384,4
378,0
406,4
406,4
11,0
14,2
Note:
516,0
479,6
The outer diameter values marked by colour depend on the used material
508,0
and heating diameter larger outer diameter.
14,2
22,0
11,3
21,3
5,0
35,0
17,7
33,7
8,0
50,0
23,3
48,3
12,5
77,0
41,1
76,1
17,5
91,0
48,9
88,9
20,0
Pipe values corelated to pressureratings acc. DIN 3239. Pressureratings and materials
acc. DIN 2401. (Wst. 1.0460; 1.0425; 1.5415; 1.7335;
1.7383). No casting materials are listed.
d3 is the outer diameter of the connected steelpipe Line 1 acc. ISO 4200-1985
6100.1.05.14
130
Technical appendix
Processing and test equipment / test facilities
Mechanical workshop
9 Machining centres for drilling, turning and milling
operations
# CNC-controlled and conventional horizontal and
vertical turning machines for workpieces up to app.
20 kN of weight
# Drilling and milling machines, CNC-controlled saw,
lapping and chipping machines, grinding machines and
turning machines
Welding shop
# Robot based welding systems for seat hard facing,
stelliting and joint welding
# Hand and machine-welding
# Electric annealing furnaces
# Manipulator for submerged arc welding
Assembly
7 Assembly and test equipment for the pressure
(tightness) test for valves up to max. DN 800 with
a max. test pressure of 1.000 bar
Transport Facilities
# Bridge cranes with max. carrying capacity of 160 kN
# Slewing cranes with max. carrying of 20 kN
# Fork lift trucks with max. carrying capacity of 75 kN
Ultrasonic test
n Type of equipment: USM35X, companies, GE
Krautkrmer
X-ray tests
n Type of equipment and capacity
2 ISO Volt 320, ISO Volt 150
all from company GE, Seiffert
131
6100.1.05.14
Technical appendix
Qualification
Approvals
Name of the testing firm Specification
or organisation

TV NORD CERT GmbH DIN EN ISO 9001
TV NORD CERT GmbH DIN EN ISO 50001
TV NORD Systems GmbH & Co. KG AD 2000 HP 0 / TRD 201 /
ASME B16.34
TV NORD Systems GmbH & Co. KG DIN EN ISO 3834-2 (EN 729-2) /
DGRL 97 / 23/EG Modul H/H1
TV NORD Systems GmbH & Co. KG KTA 3201.3 / KTA 3211.3 / 1408.3
VdTV (Bauteilkz. MLVs) TV . A . 030 - 08
TV NORD EnSys T08-85-03
(Eignungsprf. MLVs)
Eignungsprfung VGB KTA 1401 and AVS D 100/50
Global Standart Moscow GOST TR Nr. C-DE.MM06.B.00156
(Dirt scraper)
Global Standart Moscow GOST TR Nr. C-DE-MM06.B.00157
(Div. industrial valves)
Rostehnadzor Russland RTN
Promatomnadzor Minsk GOSPROMNADZOR (Belarus)
Bharat Heavy Electricals LTD 24 NRV
Paks Nuclear Power Plant KM51 / 2011
EDF EDF
Shell Nederland Raffin. BV Service group 77DAAB /
Service group 77DPBA
Shell Nederland Chemie BV Service group 77DAAB /
Service group 77DPBA
Kuwait Oil Company VEC / VA / GT / 015 / 16 / 97
Canada Canadian Registration; CSA B51
ENERGO-ATOM QS-System
Slovensk Elektrrne QS-System
Forsmark Kraftgruppe AB QS-System
GE Energy QS-System
Fire Safe ISO 10497 / API 607
And the complete documentation provided by PERSTA

quality control department is layed out with a view to
ensure that they meet the requirements which are set
out in the approvals and satisfy the user demands for
maximum operational safety.
PERSTA valves are designed, produced and tested in line
with the latest technology, PERSTA performs the following tests:
Acceptance of subsupplier
Acceptance of incoming raw materials
n Inspection of finished components and bought-in
parts in production, to ensure that they are designed in
accordance with the drawings
n Destructive and non-destructive testing
n Strength and tightness tests
n Function tests
n
n
Process tests joint welding
Normen and standards: AD; TRD; EN 288-1; EN ISO 15614-1+11; ASME IX

Materials acc. AD-HP 0
Materials acc. ISO/TR 15608 Materials based on code

1
1
1.0460
1
1
1.5415
5.1
1
1.0566
3
4.2
1.6368
4.1
5.1
1.7335
4.1
5.2
1.7383
4.2
6.4
1.4903
4.2
6.4
1.4901
6
8.1
1.4571
Ni
45
2.4858
111
(E)
121 135 141 511

(UP) (MAG) (WIG) (EB)
X
X
X
X
X
X
X
X
X
-
X
X
X
X
X
X
X
X
X
-
X
X
X
X
X
X
-
-
X
-
X
X
X
X
X
X
X
X
X
X
X
X
-
X
X
X
X
X
6100.1.05.14
132
Technical appendix
Figure number code
Figure

Type
PERSTA Code
Small globe valve (inside screw and yoke)

Small globe valve (outside screw and yoke)
Small lift check valve
Pressure gauge valve
Globe valve
Globe valve with throttle disc
Globe valve with non-rotating stem
Bellow seal globe valve
Globe valve with throttle disc and non-rotating stem
Bellow seal globe valve with throttle disc
Highpressure valve DVA 25 / 40
Highpressure valve HD 91
Highpressure valve HD 2000
Highpressure valve HD 2000 with back seat
Screw down non return valve
Stop check valve HD 2000
Lift check valve
Changeover valve DN 10-50
Changeover valve DN 65-200
Gate valve
Swing check valve
Highpressure swing check valve DRI 16 - 63
Swing check valve with lever and weight
High pressure stop check valve DRA
Gate valve, flexible wedge type, inside screw and yoke
Gate valve, flexible wedge type
Gate valve, split wedge type
High pressure gate valve DSK 16 - 63
Small gate valve, full bore
Small gate valve, reduced bore
Strainer
200 AB
200 AF/BF
240 MU
200 AD
200 AE / AJ
200 BE / BJ
200 AJ
200 AL
200 BJ
200 BL
200 BZ
200 JM
200 LM / 202 LM
200 LS / 200 LJ
240 ME
240 MM
240 MT
203 EH
203 EM
400 JJ
640 AA
640 AB
640 AE
640 AT
640 DJ
700 GA
700 HJ
700 JJ
700 JT
808 GJ
800 GJ
990 ST
990 VW
Figure number code
Example
XXX XX XX. X
Figure number code
Result
700 HJ 21. 1
Figure number
Materials
Connections
Materials
DIN-Nr.
EN-Bez.

1.0425
1.0425
1.0460
1.0460
1.0566
1.0566
1.0619
1.0619+N
1.4308
1.4308
1.4550
1.4550
1.4571
1.4571
1.4571
1.4571
1.4581
1.4581
1.4901
1.4901
1.4903
1.4903
1.5415
1.5415
1.5419
1.5419
1.6368
1.6368
1.7221
1.7221
1.7335
1.7335
1.7357
1.7357
1.7380
1.7383
Material code
(new)
Material code
(old)
P265 GH
H II
P250 GH
C22.8
P355NL1
TStE 355
GP240 GH+N
GS-C25N
GX5CrNi19-10
G-X6CrNi 18 9
X6CrNiNb18-10
X6CrNiNb18-10
X6CrNiMoTi17-12-2
X 6 CrNiMoTi 17 12 2
X6CrNiMoTi17-12-2
X 6 CrNiMoTi 17 12 2
GX5CrNiMoNb19-11-2
G-X5CrNiMoNb18 10
X10CrWMoVNb 9-2
X10CrMoVNb 9-1
X 10 CrMoVNb 9-1
16Mo3
15 Mo 3
GS-22 MO4
G 20 Mo5
15NiCuMoNb5
15 NiCuMoNb 5
G26CrMo4
GS-26 CrMo 4
13CrMo4-5
13 CrMo 44
G17CrMo5-5
GS-17 CrMo 5 5
11CrMo9-10
10 CrMo 9 10
PERSTA Code
22
21
25
11
77
89
82 (up to max. 280 C)
85
72
66
63
42
32
46
31
44
34
45
Connection type
Designation
PERSTA Code
Flange
BW Ends
Threaded sleeves
Threaded journals
Weld nipples
Pressure gauge connection
Ermeto-connection
Socket weld ends
Special connection
1
2
3
4
5
6
7
8
9
133
6100.1.05.14
Stahl-Armaturen PERSTA GmbH

Mlheimer Strae 18
59581 Warstein, Germany
Phone +49 29 02 7 62 - 02
Fax +49 29 02 7 67 03
www.persta.com
info@persta.de
6100.1.05.14
ce
n
e
i
r
e
Exp e difference
th

Persta Industrie e

Uploaded by

Copyright:

Available Formats

Persta Industrie e

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Persta Industrie e

Uploaded by

Copyright:

Available Formats

What types of valves are discussed in the document?

What types of valves are discussed in the document?

What factors should be considered for normal operating conditions of the valves?

What factors should be considered for normal operating conditions of the valves?

Valves for the industry

Industrial valves made by company Stahl-Armaturen

If the purchaser expects stresses deviating from the

Operation with liquid or gaseous media, without special

During planning and installation of the pipeline the

Please see our relevant Instruction Operational

Technical alterations reserved

Lift check valve

Lift check valve

Bellow seal globe valve / VALTRA

High pressure globe valve HD 91

High pressure globe valve HD 2000

High pressure globe valve HD 2000

Stop check valve HD 2000

High pressure globe valve DVA 25/40

with back seat

Special globe valve variants

Small gate valve / VALTRA

NPS 1/2 - 2 / DN 15-50 Class 800/10-40

700 HJ/JJ (GA)

700 HJ/JJ (GA)

Gate valve / VALTRA

Gate valve / VALTRA

High pressure gate valve DSK 10

High pressure gate valve DSK 10

High pressure gate valve DSK 10

High pressure gate valve DSK 26

High pressure gate valve DSK 16 - 63

PERSTA Type SV 97, -98, -99

Technical alterations reserved

Swing check valves

Swing check valves

Line blind valves

blind valves DPV 10

Line blind valves DPV 16-63

Butt welding ends DIN 3239 and 2559

Butt welding ends EN 12627

Processing and test equipment/test facilities

Figure number code

Technical alterations reserved

Lift check valve

Technical alterations reserved

Lift check valve

Pressure and temperature ratings

Pressure rating BW-Ends up to 160 bar

Further materials on request.

Die-forged valve body and bonnet

Free from porosity and shrink holes

Seats are hardfaced or welded on

Extremely resistant to wear

Body-bonnet connection male and female

Sealing blow out proof

Technical alterations reserved

To ease maintenance work, e.g. regrinding

Lift check valve

Globe valve AE/BE