Refining Processes 2004 PDF

Rening Processes Index
Company Index
Rening Articles
E quipment and Services
Providers
Rening Processes Index - 1
Alkylation
Alkylation, catalytic
Alkylation, sulfuric acid
Alkylationfeed preparation
AlkylationHF
Aromatics
Aromatics extractive distillation
Aromatics recovery
Asphaltoxidation
Benzene reduction
Catalytic cracking (MSCC)
Catalytic dewaxing
Catalytic reforming
Coking
Coking, exi
Coking, uid
Crude distillation
Crude topping units
Deasphalting
Deep catalytic cracking
Deep thermal conversion
Desulfurization
Dewaxing
Dewaxing/wax deoiling
Diesel upgrading
Dieselultra-low-sulfur diesel (ULSD)
Electrical desalting
Ethers
EthersETBE
EthersMTBE
Fluid catalytic cracking
Fluid catalytic crackingpretreatment
Gas treatingH
2
S removal
Gasication
Gasoline desulfurization
Gasoline desulfurization, ultra-deep
H
2
S and SWS gas conversion
H
2
S removal
H
2
S removal, Thiopaq
Hydrocracking
Hydrocracking, resid
Hydrocracking/hydrotreatingVGO/DAO
Hydrodearomatization
Hydrodesulfurization
HydrodesulfurizationUDHDS
Hydronishing
Hydronishing/hydrotreating
Hydrogen
Hydrogenation
HydrogenHTCR-based
HydrogenHTER-p based
HydrogenMethanol-to-Shift
Hydrogenrecovery
Hydrogensteam methane reforming (SMR)
Hydroprocessing, residue
Hydroprocessing, ULSD
Hydrotreating
Rening Processes Index - 2
Hydrotreatingaromatic saturation
Hydrotreatingcatalytic dewaxing
Hydrotreating, diesel
Hydrotreatinglube and wax
HydrotreatingRDS/VRDS/UFR/OCR
Hydrotreatingresid
Isomerization
Isooctane
Isooctane/isooctene
Isooctene/Isooctane/ETBE
LPG recovery
Lube and wax processing
Lube extraction
Lube hydrotreating
Lube oil rening, spent
Lube treating
Mercaptan removal
NOx abatement
NOx reduction, low-temperature
Olens recovery
Olens-butenes extractive distillation
Olens-dehydrogenation
Oligomerization of C
3
C
4
cuts
Oligomerizationpolynaphtha
Oxygen enrichment for Claus units
Oxygen enrichment for FCC units
Paraxylene
Prereforming with feed ultra purication
Resid catalytic cracking
SBS SO
3
removal process
SO
2
removal, regenerative
Sour gas treatment
Spent acid regeneration
Spent oil lube re-rening
Sulfur degassing
Sulfur recovery
Thermal gasoil process
Treatinggases
Treatinggasoline
Treatinggasoline and light hydrocarbon
liquids
Treatinggasoline desulfurization, ultra deep
Treatingjet fuel/kerosine
Treatinglight liquids
TreatingPhenolic caustic
Treatingreformer products
Treatingspent caustic deep neutralization
Treatingsweetening
Vacuum distillation
Visbreaking
Wax hydrotreating
Wet gas scrubbing (WGS)
Wet scrubbing system, EDV
White oil and wax hydrotreating
Company Index
ABB Lummus Global, Inc.
Air Products and Chemicals Inc.
Aker Kvaerner
Akzo Nobel Catalysts
Akzo Nobel Catalysts bv
Axens
BARCO
Bechtel Corp.
Belco Technologies Corp.
Black & Veatch Pritchard, Inc.
BOC Group, Inc.
CB&I Howe-Baker Process and
Technologies
CDTECH
Chevron Lummus Global LLC
ChevronTexaco Corp.
Codan Development LLC
ConocoPhillips, Technology Solutions
Division
Costain Oil, Gas & Process Ltd.
Criterion Catalyst Co., LP
Davy Process Technology Ltd.
ExxonMobil Research and
Engineering Co.
Fina Research S.A.
Fortum Oil and Gas
Foster Wheeler
Future Energy GmbH
Gas Technology Products LLC
GE Energy
Goar, Allison & Associates, Inc.
GTC Technology Inc.
Haldor Topse A/S
Hydrocarbon Technologies, Inc.
IFP Group Technologies
Kellogg Brown & Root, Inc.
Linde AG, Gas Division
Linde BOC Process Plants LLC
Lyondell Chemical Co.
Merichem Chemicals & Renery
Services LLC
Paques Bio System B.V.
PDVSA-INTEVEP
Poerner Ingenieurgesellschaft GmbH
Process Dynamics, Inc.
Research Institute of Petroleum
Processing, Sinopec
Shell Global Solutions International B.V.
Shell International Oil Products B.V.
Snamprogetti SpA
Stone & Webster Inc.
STRATCO DuPont
Technip
TOTALFINAELF
Uhde GmbH
UOP LLC
Viscolube SpA
W.R. Grace & Co.
Equipment and Services providers
ARCA Regler GmbH
Axens
Burckhardt Compression AG
DMC Clad Metal Div., Dynamic Materials Corp.
Engelhard Corporation
Fischer Valve Div., Emerson Process Management
Gas Technology Products LLC
KBC Advanced Technologies
Samson AG Mess-und Regeltechnik
SNC-Lavalin GDS
Thermo Electron Corp.
UOP LLC
US Filter
Alkylation
Application: The AlkyClean process converts light olens into alkylate
by reacting the olens with isobutane over a true solid acid catalyst.
AlkyCleans unique catalyst, reactor design and process scheme allow
operation at low external isobutene-to-olen ratios while maintaining
excellent product quality.
Products: Alkylate is a high-octane, low-Rvp gasoline component used
for blending in all grades of gasoline.
Description: The light olen feed is combined with the isobutene make-
up and recycle and sent to the alkylation reactors which convert the
olens into alkylate using a solid acid catalyst (1). The AlkyClean process
uses a true solid acid catalyst to produce alkylate, eliminating the safety
and environmental hazards associated with liquid acid technologies. Si-
multaneously, reactors are undergoing a mild liquid-phase regeneration
using isobutene and hydrogen and, periodically, a reactor undergoes a
higher temperature vapor phase hydrogen strip (2). The reactor and mild
regeneration efuent is sent to the product-fractionation section, which
produces propane, n-butane and alkylate, while also recycling isobutene
and recovering hydrogen used in regeneration for reuse in other renery
hydroprocessing units (3). The AlkyClean process does not produce any
acid soluble oils (ASO) or require post treatment of the reactor efuent or
nal products.
Product: The C
5
+
alkylate has a RON of 9398 depending on processing
conditions and feed composition.
Economics:
Investment (basis 10,000-bpsd unit) $/bpsd 3,100
Operating cost, $/gal 0.47
Installation: Demonstration unit at Fortums Porvoo, Finland Renery.
Reference: The Process: A new solid acid catalyst gasoline alkylation
technology, NPRA 2002 Annual Meeting, March 1719, 2002.
Licensor: ABB Lummus Global, Akzo Nobel Catalysts and Fortum Oil
and Gas.
Alkylation
Application: Convert propylene, amylenes, butylenes and isobutane to
the highest quality motor fuel using ReVAP (Reduce Volatility Alkylation
Process) alkylation.
Products: An ultra-low-sulfur, high-octane and low-Rvp blending stock
for motor and aviation fuels.
Description: Dry liquid feed containing olens and isobutane is charged
to a combined reactor-settler (1). The reactor uses the principle of dif-
ferential gravity head to effect catalyst circulation through a cooler pri-
or to contacting highly dispersed hydrocarbon in the reactor pipe. The
hydrocarbon phase that is produced in the settler is fed to the main
fractionator (2), which separates LPG-quality propane, isobutane recycle,
n-butane and alkylate products. A small amount of dissolved catalyst is
removed from the propane product by a small stripper tower (3). Major
process features are:
Gravity catalyst circulation (no catalyst circulation pumps re-
quired)
Low catalyst consumption
Low operating cost
Superior alkylate qualities from propylene, isobutylene and amyl-
ene feedstocks
Onsite catalyst regeneration
Environmentally responsible (very low emissions/waste)
Between 60% and 90% reduction in airborne catalyst release over
traditional catalysts
Can be installed in all licensors HF alkylation units.
With the proposed reduction of MTBE in gasoline, ReVAP offers sig-
nicant advantages over sending the isobutylene to a sulfuric-acid-al-
kylation unit or a dimerization plant. ReVAP alkylation produces higher
octane, lower Rvp and endpoint product than a sulfuric-acid-alkylation
unit and nearly twice as many octane barrels as can be produced from
a dimerization unit.
Yields: Feed type
Butylene Propylene-butylene mix
Composition (lv%)
Propylene 0.8 24.6
Propane 1.5 12.5
Butylene 47.0 30.3
i-Butane 33.8 21.8
n-Butane 14.7 9.5
i-Pentane 2.2 1.3
Alkylate product
Gravity, API 70.1 71.1
Rvp, psi 67 67
ASTM 10%, F 185 170
ASTM 90%, F 236 253
RONC 96.0 93.5
Per bbl olefin converted

i-Butane consumed, bbl 1.139 1.175
Alkylate produced, bbl 1.780 1.755
Installation: 140 worldwide licenses.
Licensor: Technology Solutions Division of ConocoPhillips.
Alkylation, continued
Alkylation
Application: The Topse xed-bed alkylation (FBA) technology applies
a unique xed-bed reactor system with a liquid superacid catalyst ab-
sorbed on a solid support. FBA converts isobutane with propylene, bu-
tylene and amylenes to produce branched chain hydrocarbons. As an
alternative, FBA can conveniently be used to alkylate isopentane as a
means of disposing isopentane for Rvp control purpose.
Products: A high-octane, low-Rvp and ultra-low-sulfur blending stock
for motor and aviation gasoline.
Description: The FBA process combines the benets of a liquid catalyst
with the advantages of a xed-bed reactor system. Olen and isobutane
feedstocks are mixed with a recycle stream of isobutane and charged to
the reactor section (1). The olens are fully converted over a support-
ed liquid-phase catalyst conned within a mobile, well-dened catalyst
zone. The simple xed-bed reactor system allows easy monitoring and
maintenance of the catalyst zone with no handling of solids.
Traces of dissolved acid in the net reactor efuent are removed
quantitatively in a compact and simple-to-operate efuent treatment
unit (2). In the fractionation section (3), the acid-free net reactor efuent
is split into propane, isobutane, n-butane and alkylate. The unique reac-
tor concept allows an easy and selective withdrawal of small amounts of
passivated acid. The acid catalyst is fully recovered in a compact catalyst
activity maintenance unit (4). The integrated, inexpensive and onsite-
maintenance of catalyst activity is a distinct feature of the FBA process.
Other signicant characteristics of FBA include:
High exibility (feedstock, operation temperature)
Low operating costs
Low catalyst consumption.
Process performance:
Olefin feed type
MTBE raffinate FCC C
4
cut C
3
C
5
cut
Alkylate product
RON (C
5
+) 98 95 93
MON (C
5
+) 95 92 91
Economics: (Basis: MTBE rafnate, inclusive feed pretreatment and on-
site catalyst activity maintenance)
Investment (basis: 6,000 bpsd unit), $ per bpsd 5,600
Utilities, typical per bbl alkylate:
Electricity, kWh 10
Steam, MP (150 psig), lb 60
Steam, LP (50 psig), lb 200
Water, cooling (20F rise), gal10
3
2.2
Licensor: Haldor Topse A/S.

Alkylation
Application: To combine propylene, butylenes and amylenes with isobutane
in the presence of strong sulfuric acid to produce high-octane branched
chain hydrocarbons using the Efuent Refrigeration Alkylation process.
Products: Branched chain hydrocarbons for use in high-octane motor
fuel and aviation gasoline.
Description: Plants are designed to process a mixture of propylene,
butylenes and amylenes. Olens and isobutane-rich streams along with
a recycle stream of H
2
SO
4
are charged to the STRATCO Contactor reac-
tor (1). The liquid contents of the Contactor reactor are circulated at high
velocities and an extremely large amount of interfacial area is exposed
between the reacting hydrocarbons and the acid catalyst from the acid
settler (2). The entire volume of the liquid in the Contactor reactor is main-
tained at a uniform temperature, less than 1F between any two points
within the reaction mass. Contactor reactor products pass through a ash
drum (3) and deisobutanizer (4). The refrigeration section consists of a
compressor (5) and depropanizer (6).
The overhead from the deisobutanizer (4) and efuent refrigerant
recycle (6) constitutes the total isobutane recycle to the reaction zone.
This total quantity of isobutane and all other hydrocarbons is maintained
in the liquid phase throughout the Contactor reactor, thereby serving to
promote the alkylation reaction. Onsite acid regeneration technology is
also available.
Product quality: The total debutanized alkylate has RON of 92 to 96
clear and MON of 90 to 94 clear. When processing straight butylenes,
the debutanized total alkylate has RON as high as 98 clear. Endpoint of
the total alkylate from straight butylene feeds is less than 390F, and less
than 420F for mixed feeds containing amylenes in most cases.
Economics (basis: butylene feed):
Investment (basis: 10,000-bpsd unit), $ per bpsd 3,500
Utilities, typical per bbl alkylate:
Electricity, kWh 13.5
Steam, 150 psig, lb 180
Water, cooling (20F rise), 10
3
gal 1.85
Acid, lb 15
Caustic, lb 0.1
Installation: Nearly 600,000 bpsd installed capacity.
Reference: Hydrocarbon Processing, Vol. 64, No. 9, September 1985,
pp. 6771.
Licensor: STRATCO, DuPont.
Alkylation
Application: The Alkad process is used with HF alkylation technology to
reduce aerosol formation in the event of an HF release, while maintain-
ing unit operability and product quality. The Alkad process is a passive
mitigation system that will reduce aerosol from any leak that occurs
while additive is in the system.
Description: The additive stripper sends acid, water and light-acid sol-
uble oils overhead and on to the acid regenerator. Heavy acid soluble
oils and the concentrated HF-additive complex are sent to the additive
stripper bottoms separator. From this separator the polymer is sent to
neutralization, and the HF-additive complex is recycled to the reactor
section. The acid regenerator removes water and light-acid soluble oils
from the additive stripper overhead stream. The water is in the form of
a constant boiling mixture (CBM) of water and HF.
There is no expected increase in the need for operator manpower.
Maintenance requirements are similar to equipment currently in stan-
dard operation in an HF alkylation unit in similar service.
Experience: ChevronTexaco, the co-developer of the Alkad process, in-
stalled facilities to use this technology in the HF Alkylation unit at their
former El Dorado, Kansas, renery. This unit began initial operations in
1994.
Installation: One unit is under construction.
Licensor: UOP LLC and ChevronTexaco Corp.

Alkylation
Application: UOPs Indirect Alkylation (InAlk) process uses solid catalysts
to convert light olens (mainly C
4
but also C
3
and C
5
) to alkylate.
Description: The InAlk process makes premium alkylate using a combi-
nation of commercially proven technologies. Iso-butene reacts with itself
or with other C
3
C
5
olens via polymerization. The resulting mixture of
higher molecular weight iso-olens may then be hydrogenated to form
a high-octane parafnic gasoline blendstock that is similar to alkylate,
but usually higher in octane, or it may be left as an olenic high-octane
gasoline blending component.
Either resin or solid phosphoric acid (SPA) catalysts are used to po-
lymerize the olens. Resin catalyst primarily converts iso-butene. SPA
catalyst also converts n-butenes. The saturation section uses either a
base-metal or noble-metal catalyst.
Feed: A wide variety of feeds can be processed in the InAlk process.
Typical feeds include FCC-derived light olens, steam-cracker olens
and iC
4
dehydrogenation olens.
Installation: The InAlk process is an extension of UOPs catalytic con-
densation and olen saturation technologies. UOP has licensed and de-
signed more than 400 catalytic condensation units for the production of
polygasoline and petrochemical olens and more than 200 hydrogena-
tion units of various types. Currently ve InAlk units are in operation.
Licensor: UOP LLC.
Alkylation, catalytic
Application: CDAlky process is an advanced sulfuric acid-catalyzed al-
kylation process that reacts light olen streams from renery sources,
such as uid catalytic cracking (FCC) units or from steam-cracking units,
with iso-parafns to produce motor fuel alkylate.
Description: The patented CDAlky process is an advanced sulfuric acid-
catalyzed alkylation process for the production of motor fuel alkylate. The
process ow diagram shows the basic conguration to process a mixed
C
4
-olen feed and produce a bright, clear, high-quality motor fuel alkyl-
ate, without the need for water/caustic washes or bauxite treatment.
This process yields a higher-quality product while consuming sig-
nicantly less acid than conventional technologies. The ow scheme is
also less complex than conventional designs, which reduces capital and
operating costs.
Conventional sulfuric-acid alkylation units use mechanical mixing
in their contactors to achieve the required contact between acid and
hydrocarbon phases, and are characterized by high acid consumption.
In addition, conventional technologies are unable to take the full ben-
et of operating at lower temperature, which substantially improves
alkylate quality and lowers acid consumption.
CDTECH has developed a novel contactor that operates at lower
temperatures and substantially reduced acid consumption50%+. The
CDAlky process uses conventional product fractionation, which can con-
sist of a single column or two columns. This process has been designed
to make it possible to reuse equipment from idled facilities.
The benets of the CDAlky process include:
Lower acid consumption
Lower utilities
Reduced operating cost
Reduced environmental exposure
Higher octane product
Lower CAPEXsimpler owsheet with fewer pieces of equipment
Highly exible operation rangemaximum absolute product oc-
tane or maximum octane barrels
Lower maintenanceno mechanical agitator or complex seals
Less corrosion due to dry system
No caustic waste stream
Installation: Consistent with time-tested methodology for developing
new processes, CDTECH has been operating a 2-bpd pilot plant in this
novel mode of operation for an extended time period without the pen-
alties associated with conventional technologies.
Licensor: CDTECH.

Alkylation, sulfuric acid

Application: Auto-refrigerated sulfuric-acid catalyzed process that com-
bines butylene (and propylene or pentylene if desired) with isobutane
to produce high-octane gasoline components that are particularly at-
tractive in locations that are MON limited. Technology can be installed
grassroots or retrot into existing alkylation facilities.
Products: A low-sulfur, low-Rvp, highly isoparafnic, high-octane (espe-
cially MON) gasoline blendstock is produced from this alkylation process.
Description: Olen feed and recycled isobutane are introduced into the
stirred, autorefrigerated reactor (1). Mixers provide intimate contact be-
tween the reactants and the acid catalyst. Highly efcient autorefrig-
eration removes heat of reaction heat from the reactor. Hydrocarbons
vaporized from the reactor to provide cooling are compressed (2) and
returned to the reactor. A depropanizer (3), which is fed by a slipstream
from the refrigeration section, is designed to remove any propane intro-
duced to the plant with the feeds.
Hydrocarbon products are separated from the acid in the settler
containing proprietary internals (4). In the deisobutanizer (5) isobutane
is recovered and recycled along with makeup isobutane to the reactor.
Butane is removed from alkylate in the debutanizer (6) to produce a
low Rvp, high-octane alkylate product. A small acid stream containing
acid-soluble oil byproducts is removed from the unit and is either regen-
erated on site or sent to an off-site sulfuric acid regeneration facility to
recover acid strength.
Yields:
Alkylate yield 1.8 bbl C
5
+/bbl butylene feed
Isobutane required 1.2 bbl/bbl butylene feed
Alkylate quality 97 RON / 94 MON
Rvp, psi 3
Utilities: Typical per barrel of alkylate produced:
Water, cooling, Mgal 2
Power, kWh 9
Steam, lb 200
H
2
SO
4
, lb 19
NaOH, 100%, lb 0.1
Operating experience: Extensive commercial experience in both Exxon-
Mobil and licensee reneries, and a total operating capacity of 119,000-
bpsd at 11 locations worldwide. Unit capacities range from 2,000 to
30,000 bpd, and single reactor/settler trains with capacities up to 9,500
bpsd. Recent commercial applications include a revamp at ExxonMobils
Altona, Australia, renery and a new unit at TNK-BPs Ryazan, Russia
renery, which is currently under construction.
Continued
Technical advantages:
Autorefrigeration is thermodynamically more efcient, allows low-
er reactor temperatures that favor better product quality, and low-
ers energy usage.
Staged reactor results in a high average isobutane concentration,
which favors high product quality.
Low space velocity results in high product quality and reduced
ester formation eliminating corrosion problems in fractionation
equipment.
Low reactor operating pressure translates into high reliability for
the mechanical seals for the mixers, which operate in the vapor
phase.
Economic advantages:
Lower capital investmentSimple reactor/settler conguration,
less compression requirements translate into a signicant invest-
ment savings compared to indirect refrigeration systems
Lower operating costsAutorefrigeration, lower mixing and com-
pression power requirements translate into lower operating costs
Better economy of scaleReactor system is simple and easily ex-
pandable, with 9,500 bpsd single train capacities easily achiev-
able.
Reference: Lerner, H., Exxon sulfuric acid alkylation technology, Hand-
book of Petroleum Rening Processes, 2nd edition, R. A. Meyers, Ed.,
pp. 1.31.14.
Licensor: ExxonMobil Research and Engineering Co.
Alkylation, sulfuric acid, continued
Application: Upgrades alkylation plant feeds with Alkyning process.
Description: Diolens and acetylenes in the C
4
(or C
3
C
4
) feed react se-
lectively with hydrogen in the liquid-phase, xed-bed reactor under mild
temperature and pressure conditions. Butadiene and, if C
3
s are present,
methylacetylene and propadiene are converted to olens.
The high isomerization activity of the catalyst transforms 1-butene
into cis- and trans-2-butenes, which affords higher octane-barrel pro-
duction.
Good hydrogen distribution and reactor design eliminate channeling
while enabling high turndown ratios. Butene yields are maximized, hy-
drogen is completely consumed and, essentially, no gaseous byproducts
or heavier compounds are formed. Additional savings are possible when
pure hydrogen is available, eliminating the need for a stabilizer. The pro-
cess integrates easily with the C
3
/C
4
splitter.
Alkyfining performance and impact on HF alkylation product:
The results of an Alkyning unit treating an FCC C
4
HF alkylation
unit feed containing 0.8% 1,3-butadiene are:
Butadiene in alkylate, ppm < 10
1-butene isomerization, % 70
Butenes yield, % 100.5
RON increase in alkylate 2
MON increase in alkylate 1
Alkylate end point reduction, C 20
The increases in MON, RON and butenes yield are reected in a
substantial octane-barrel increase while the lower alkylate end point re-
duces ASO production and HF consumption.
Economics:
Investment:
Grassroots ISBL cost:
For an HF unit, $/bpsd 430
For an H
2
SO
4
unit, $/bpsd 210
Annual savings for a 10,000-bpsd alkylation unit:
HF unit, US$ 4.1 million
H
2
SO
4
unit, US$ 5.5 million
Installation: Over 80 units are operating with a total installed capacity
of 700,000 bpsd.
Licensor: Axens.

AlkylationHF
Application: HF Alkylation improves gasoline quality by adding clean-
burning, mid-boiling-range isoparafns and reducing gasoline pool va-
por pressure and olen content by conversion of C
3
C
5
olen compo-
nents to alkylate.
Description: The alkylation reaction catalytically combines C
3
C
5
olens
with isobutane to produce motor-fuel alkylate. Alkylation takes place in
the presence of HF catalyst under conditions selected to maximize alkyl-
ate yield and quality.
The reactor system is carefully designed to ensure efcient contact-
ing and mixing of hydrocarbon feed with the acid catalyst. Efcient heat
transfer conserves cooling water supply. Acid inventory in the reactor
system is minimized by combining high heat-transfer rates and lower
total acid circulation.
Acid regeneration occurs in the acid regenerator or via a patented
internal-acid-regeneration method. Internal regeneration allows the
rener to shutdown the acid regenerator, thereby realizing a utility
savings as well as reducing acid consumption and eliminating polymer
disposal.
Feed: Alkylation feedstocks are typically treated to remove sulfur and
water. In cases where MTBE and TAME rafnates are still being pro-
cessed, an oxygenate removal unit (ORU) may be desirable.
Selective hydrogenation of butylene feedstock is recommended to
reduce acid regeneration requirements, catalyst (acid) consumption and
increase alkylate octane by isomerizing 1-butene to 2-butene.
Efficiency: HF Alkylation remains the most economically viable method
for the production of alkylate. The acid consumption rate for HF Alkyla-
tion is less than 1/100th the rate for sulfuric alkylation units. And un-
like sulfuric alkylation units, HF Alkylation does not require refrigeration
equipment to maintain a low reactor temperature.
Installations: Over 20 UOP licensed HF alkylation units are in operation.
Licensor: UOP LLC.
Aromatics
Application: The technology produces benzene and xylenes from tolu-
ene and/or heavy aromatics streams. The technology features a propri-
etary catalyst and can accommodate varying ratios of feedstock, while
maintaining high activity and selectivity.
Description: The technology encompasses three main processing areas:
feed preparation, reactor and product stabilization sections. The heavy
aromatics stream (usually derived from catalytic reformate) is fed to a
C
10
/C
11
splitter. The overhead portion, along with any toluene that may
be available, is the feed to the transalkylation reactor section. The com-
bined feed is mixed with hydrogen, vaporized, and fed to the reactor.
The un-reacted hydrogen is recycled for re-use. The product stream is
stabilized to remove fuel gas and other light components.
The process reactor is charged with a proprietary catalyst, which
exhibits good exibility to feed stream variations, including 100% C
9
+
aromatics. Depending on the feed composition, the xylene yield can
vary from 27 to 35% and C
9
conversion from 53 to 67%.
Process advantages include:
Simple, low cost xed-bed reactor design
Selective toward xylene production, with high toluene/C
9
conver-
sion rates
Physically stable catalyst
Flexible to handle up to 100% C
9
+ components in feed
Flexible to handle benzene recycle to increase xylene yields
Moderate operating parameters; catalyst can be used as replace-
ment to other transalkylation units, or in grassroots designs
Decreased hydrogen consumption due to low cracking rates
Efcient heat integration scheme, reduces energy consumption.
Licensor: GTC Technology Inc., using catalyst supplied by Sd-Chemie
Inc.
Aromatics extractive distillation

Application: Recovery of high-purity aromatics from reformate, pyrolysis
gasoline or coke-oven light oil using extractive distillation.
Description: In Uhdes proprietary extractive distillation (ED) Morphylane
process, a single-compound solvent, N-Formylmorpholine (NFM), alters the
vapor pressure of the components being separated. The vapor pressure of
the aromatics is lowered more than that of the less soluble nonaromatics.
Nonaromatics vapors leave the top of the ED column with some solv-
ent, which is recovered in a small column that can either be mounted on
the main column or installed separately.
Bottom product of the ED column is fed to the stripper to separate
pure aromatics from the solvent. After intensive heat exchange, the lean
solvent is recycled to the ED column. NFM perfectly satises the neces-
sary solvent properties needed for this process including high selectivity,
thermal stability and a suitable boiling point.
Economics:
Pygas feedstock:
Benzene Benzene/toluene
Production yield
Benzene 99.95% 99.95%
Toluene 99.98%
Quality
Benzene 30 wt ppm NA* 80 wt ppm NA*
Toluene 600 wt ppm NA*
Consumption
Steam 475 kg/t ED feed 680 kg/t ED feed**
Reformate feedstock with low-aromatics content (20 wt%):
Benzene
Quality
Benzene 10 wt ppm NA*
Consumption
Steam 320 kg/t ED feed
*Maximum content of nonaromatics
**Including benzene/toluene splitter
Installation: Fifty Morphylane plants (total capacity of more than 6
MMtpy).
References: Emmrich, G., F. Ennenbach and U. Ranke, Krupp Uhde
Processes for Aromatics Recovery, European Petrochemical Technology
Conference, June 2122, 1999, London.
Emmrich, G., U. Ranke and H. Gehrke, Working with an extractive
distillation process, Petroleum Technology Quarterly, Summer 2001, p.
125.
Licensor: Uhde GmbH.

Aromatics recovery
Application: GT-BTX is an aromatics recovery process. The technology
uses extractive distillation to remove benzene, toluene and xylene (BTX)
from renery or petrochemical aromatics streams such as catalytic re-
formate or pyrolysis gasoline. The process is superior to conventional
liquid-liquid and other extraction processes in terms of lower capital and
operating costs, simplicity of operation, range of feedstock and solvent
performance. Flexibility of design allows its use for grassroots aromatics
recovery units, debottlenecking or expansion of conventional extraction
systems.
Description: The technology has several advantages:
Less equipment required, thus, signicantly lower capital cost
compared to conventional liquid-liquid extraction systems
Energy integration reduces operating costs
Higher product purity and aromatic recovery
Recovers aromatics from full-range BTX feedstock without pre-
fractionation
Distillation-based operation provides better control and simplied
operation
Proprietary formulation of commercially available solvents exhibits
high selectivity and capacity
Low solvent circulation rates
Insignicant fouling due to elimination of liquid-liquid contactors
Fewer hydrocarbon emission sources for environmental benets
Flexibility of design options for grassroots plants or expansion of
existing liquid-liquid extraction units.
Hydrocarbon feed is preheated with hot circulating solvent and fed
at a midpoint into the extractive distillation column (EDC). Lean solvent
is fed at an upper point to selectively extract the aromatics into the col-
umn bottoms in a vapor/liquid distillation operation. The nonaromatic
hydrocarbons exit the top of the column and pass through a condenser.
A portion of the overhead stream is returned to the top of the column as
reux to wash out any entrained solvent. The balance of the overhead
stream is the rafnate product, requiring no further treatment.
Rich solvent from the bottom of the EDC is routed to the solvent-re-
covery column (SRC), where the aromatics are stripped overhead. Strip-
ping steam from a closed-loop water circuit facilitates hydrocarbon re-
moval. The SRC is operated under a vacuum to reduce the boiling point
at the base of the column. Lean solvent from the bottom of the SRC
is passed through heat exchange before returning to the EDC. A small
portion of the lean circulating solvent is processed in a solvent-regenera-
tion step to remove heavy decomposition products.
The SRC overhead mixed aromatics product is routed to the puri-
cation section, where it is fractionated to produce chemical-grade ben-
zene, toluene and xylenes.
Continued
Economics: Estimated installed cost for a 15,000-bpd GT-BTX extraction
unit processing BT-reformate feedstock is $12 million (US Gulf Coast
2004 basis).
Installations: Three grassroots applications with other cases in design
and construction.
Licensor: GTC Technology Inc.
Aromatics recovery, continued
Asphaltoxidation
Application: Biturox, a continuous oxidation process, converts suitable
feedstock blends at elevated pressure and temperature by a specially
designed reactor into road paving and industrial asphalt (bitumen) with
optimized properties (e.g. PEN Index).
Feed: Long and short resides from crudes with densities below 36API,
and renery side streams such as VGO, deasphalting pitch, solvent ren-
ing extracts, visbreaker bottoms, etc., as composed blend.
Description: The different feed components (A,B,C) are blended within
the unit and pumped via a feed/product heat-exchanger (1) to the reac-
tor vessel (2). The reactor is a vertical carbon-steel cylinder, equipped
with a multi-stage stirrer (3) and a bafe system (4), that control the
recirculation of the liquid and air dispersion within the reactor.
The oxidation processes operate on ow-controlled compressed air
(5), which is injected together with a small amount of water (6). The
internal cooling via water avoids local over-heating and prevents coke
formation and deposits within the reactor. A stable, homogenous pro-
cess temperature is crucial for the production of high-quality asphalt.
The nished product is pumped via the feed/product heat-exchanger (1)
to storage.
Offgas from the reaction (oxygen content approx. 2%) is scrubbed
(7) and is thermally treated in an incinerator (8) or sent to another ren-
ery offgas treating system.
For specic conditions related to feed and/or nished products pe-
culiarities, a two-stage Biturox-process is recommended.
Operating conditions:
Pressure, psig 29
Temperature, F 520
Oxygen utilization, % 90
Residence time paving grades approx. 2 hrs
industrial grades approx. 5 hrs
Yields: The Biturox process enables the userstarting from a great vari-
ety of (inexpensive) feedstock componentsto manufacture stable and
homogenous bitumen of improved PEN Indices, exceeding the standards
and requirements of chemical and construction industries.
Economics:
Investment, US$/bpsd: approx. 850
(basis 6000 bpsd, incl. standard offgas treatment)
Utilities for reactor section (per reactor cuft)
Air, cf/h 30
Water, gal/h 0.15
Electricity, kW 0.06
Steam (50 psig), lb/h: 0.12
Maintenance minimum
Turnaround interval, yr 2

Continued
Installation: Poerner has licensed over 25 Biturox Oxidation Units world-
wide with a total capacity of 28.9 million bbl/y and performed over 200
pilot tests on all important bitumen crude bases and blends.
Reference: Poerner, A., How to use less expensive crudes for making
quality bitumen, The Singapore Asphalt Conference 1996.
Licensor: Poerner Ingenieurgesellschaft GmbH.
Asphaltoxidation, continued
Benzene reduction
Application: Benzene reduction from reformate, with the Benfree pro-
cess, using integrated reactive distillation.
Description: Full-range reformate from either a semiregenerative or CCR
reformer is fed to the reformate splitter column, shown above. The split-
ter operates as a dehexanizer lifting C
6
and lower-boiling components
to the overhead section of the column. Benzene is lifted with the light
ends, but toluene is not. Since benzene forms azeotropic mixtures with
some C
7
parafn isomers, these fractions are also entrained with the
light fraction.
Above the feed injection tray, a benzene-rich light fraction is withdrawn
and pumped to the hydrogenation reactor outside the column. A pump
enables the reactor to operate at higher pressure than the column, thus
ensuring increased solubility of hydrogen in the feed.
A slightly higher-than-chemical stoichiometric ratio of hydrogen to ben-
zene is added to the feed to ensure that the benzene content of the
resulting gasoline pool is below mandated levels, i.e., below 1.0 vol%
for many major markets. The low hydrogen ow minimizes losses of
gasoline product in the offgas of the column. Benzene conversion to
cyclohexane can easily be increased if even lower benzene content is
desired. The reactor efuent, essentially benzene-free, is returned to the
column.
The absence of benzene disrupts the benzene-iso-C
7
azeotropes, there-
by ensuring that the latter components leave with the bottoms fraction
of the column. This is particularly advantageous when the light refor-
mate is destined to be isomerized, because iso-C
7
parafns tend to be
cracked to C
3
and C
4
components, thus leading to a loss of gasoline
production.
Economics:
Investment, Grassroots ISBL cost, $/bpsd: 300
Combined utilities, $/bbl 0.17
Hydrogen Stoichiometric to benzene
Catalyst, $/bbl 0.01
Installation: Twenty-six benzene reduction units have been licensed.
Licensor: Axens.
Catalytic cracking (MSCC)

Application: To selectively convert gas oils and residual feedstocks to high-
er-value cracked products such as light olens, gasoline and distillates.
Description: The MSCC process uses a uid catalyst and a novel contact-
ing arrangement to crack heavier materials into a highly selective yield
of light olens, gasoline and distillates. A distinguishing feature of the
process is that the initial contact of oil and catalyst occurs without a riser
in a very short residence time followed by a rapid separation of initial re-
action products. Because there is no riser and the catalyst is downow-
ing, startup and operability are outstanding.
The conguration of an MSCC unit has the regenerator (1) at a
higher elevation than the reactor (2). Regenerated catalyst falls down a
standpipe (3), through a shaped opening (4) that creates a falling curtain
of catalyst, and across a well-distributed feed stream. The products from
this initial reaction are quickly separated from the catalyst. The catalyst
then passes into a second reaction zone (5), where further reaction and
stripping occurrs. This second zone can be operated at a higher tem-
perature, which is achieved through contact with regenerated catalyst.
Since a large portion of the reaction product is produced under very
short time conditions, the reaction mixture maintains good product ole-
nicity and retains hydrogen content in the heavier liquid products. Ad-
ditional reaction time is available for the more-difcult-to-crack species
in the second reaction zone/stripper.
Stripped catalyst is airlifted back to the regenerator where coke depos-
its are burned, creating clean, hot catalyst to begin the sequence again.
Installations: Four MSCC units are currently in operation with another
in design/construction.
Reference: Short-Contact-Time FCC, AIChE 1998 Spring Meeting,
New Orleans.
Licensor: UOP LLC (in cooperation with BARCO).
Catalytic dewaxing
Application: Use the ExxonMobil Selective Catalytic Dewaxing (MSDW)
process to make high VI lube base stock.
Products: High VI / low-aromatics lube base oils (light neutral through
bright stocks). Byproducts include fuel gas, naphtha and low-pour diesel.
Description: MSDW is targeted for hydrocracked or severely hydrotreated
stocks. The improved selectivity of MSDW for the highly isoparafnic-lube
components results in higher lube yields and VIs. The process uses mul-
tiple catalyst systems with multiple reactors. Internals are proprietary (the
Spider Vortex Quench Zone technology is used). Feed and recycle gases
are preheated and contact the catalyst in a down-ow-xed-bed reactor.
Reactor efuent is cooled, and the remaining aromatics are saturated in a
post-treat reactor. The process can be integrated into a lube hydrocracker
or lube hydrotreater. Post-fractionation is targeted for client needs.
Temperatures, F 550 to 800
Hydrogen partial pressures, psig 500 to 2,500
LHSV 0.4 to 3.0
Conversion depends on feed wax content
Pour point reduction as needed.
Yields:
Light neutral Heavy neutral
Lube yield, wt% 94.5 96.5
C
1
C
4
, wt% 1.5 1.0
C
5
400F, wt% 2.7 1.8
400F Lube, wt% 1.5 1.0
H
2
cons, scf / bbl 100 300 100 300
Economics: $3,000 5,500 per bpsd installed cost (US Gulf Coast).
Installation: Eight units are operating and four are in design.

Catalytic reforming
Application: Upgrade various types of naphtha to produce high-octane
reformate, BTX and LPG.
Description: Two different designs are offered. One design is conventional
where the catalyst is regenerated in place at the end of each cycle. Oper-
ating normally in a pressure range of 12 to 25 kg /cm
2
(170 to 350 psig)
and with low pressure drop in the hydrogen loop, the product is 90 to 100
RONC. With its higher selectivity, trimetallic catalysts RG582 and RG682
make an excellent catalyst replacement for semi-regenerative reformers.
The second, the advanced Octanizing process, uses continuous cata-
lyst regeneration allowing operating pressures as low as 3.5 kg /cm
2
(50
psig). This is made possible by smooth-owing moving bed reactors (13)
which use a highly stable and selective catalyst suitable for continuous
regeneration (4). Main features of Axens regenerative technology are:
Side-by-side reactor arrangement, which is very easy to erect and
consequently leads to low investment cost.
The Regen C
2
catalyst regeneration system featuring the dry burn
loop, completely restores the catalyst activity while maintaining its
specic area for more than 600 cycles.
Finally, with the new CR401 (gasoline mode) and AR501 (aromatics
production) catalysts specically developed for ultra-low operating pres-
sure and the very effective catalyst regeneration system, reners operat-
ing Octanizing or Aromizing processes can obtain the highest hydrogen,
C
5
+ and aromatics yields over the entire catalyst life.
Yields: Typical for a 90C to 170C (176F to 338F) cut from light Ara-
bian feedstock: Conventional Octanizing
Oper. press., kg /cm
2
1015 <5
Yield, wt% of feed:
Hydrogen 2.8 3.8
C
5
+ 83 88
RONC 100 102
MONC 89 90.5
Economics:
Investment: Basis 25,000 bpsd continuous octanizing unit, battery
limits, erected cost, US$ per bpsd 1,800
Utilities: typical per bbl feed:
Fuel, 10
3
kcal 65
Steam, net, HP, kg 12.5
Water, boiler feed, m
3
0.03
Installation: Of 111 units licensed, 64 units are designed with continu-
ous regeneration technology capability.
Reference: Continuing Innovation In Cat Reforming, NPRA Annual
Meeting, March 15 17, 1998, San Antonio.
Continued
Fixed Bed Reformer Revamp Solutions for Gasoline Pool Improve-
ment, Petroleum Technology Quarterly, Summer 2000.
Increase reformer performance through catalytic solutions, Sev-
enth ERTC, November 2002, Paris.
Squeezing the most out of xed-bed reactors, Hart Show Special,
NPRA 2003 Annual.
Licensor: Axens.
Catalytic reforming, continued
Catalytic reforming
Application: Increase the octane of straight-run or cracked naphthas for
gasoline production.
Products: High-octane gasoline and hydrogen-rich gas. Byproducts may
be LPG, fuel gas and steam.
Description: Semi-regenerative multibed reforming over platinum or bi-
metallic catalysts. Hydrogen recycled to reactors at the rate of 3 mols /
mol to 7 mols /mol of feed. Straight-run and /or cracked feeds are typi-
cally hydrotreated, but low-sulfur feeds (<10 ppm) may be reformed
without hydrotreatment.
Operating conditions: 875F to 1,000F and 150 psig to 400 psig reac-
tor conditions.
Yields: Depend on feed characteristics, product octane and reactor pres-
sure. The following yields are one example. The feed contains 51.4%
parafns, 41.5% naphthenes and 7.1% aromatics, and boils from 208F
to 375F (ASTM D86). Product octane is 99.7 RONC and average reactor
pressure is 200 psig.
Component wt% vol%
H
2
2.3 1,150 scf/bbl
C
1
1.1
C
2
1.8
C
3
3.2
iC
4
1.6
nC
4
2.3
C
5
+ 87.1
LPG 3.7
Reformate 83.2
Economics:
Utilities, (per bbl feed)
Fuel, 10
3
Btu release 275
Water, cooling (20F rise), gal 216
Steam produced (175 psig sat), lb 100
Licensor: CB&I Howe-Baker Process and Technology.

Catalytic reforming
Application: The CCR Platforming process is used throughout the world
in the petroleum and petrochemical industries. It produces feed for an
aromatics complex or a high-octane gasoline blending product and a
signicant amount of hydrogen.
Description: Hydrotreated naphtha feed is combined with recycle hy-
drogen gas and heat exchanged against reactor efuent. The combined
feed is then raised to reaction temperature in the charge heater and sent
to the reactor section.
Radial-ow reactors are arranged in a vertical stack. The predomi-
nant reactions are endothermic; so an interheater is used between each
reactor to reheat the charge to reaction temperature. The efuent from
the last reactor is heat exchanged against combined feed, cooled and
split into vapor and liquid products in a separator. The vapor phase is
hydrogen-rich. A portion of the gas is compressed and recycled back to
the reactors. The net hydrogen-rich gas is compressed and charged to-
gether with the separator liquid phase to the product recovery section.
This section is engineered to provide optimum performance.
Catalyst ows vertically by gravity down the reactor stack. Over
time, coke builds up on the catalyst at reaction conditions. Partially de-
activated catalyst is continually withdrawn from the bottom of the reac-
tor stack and transferred to the CCR regenerator.
Installation: UOP commercialized the CCR Platforming process in 1971
and now has commissioned more than 180 units (more than 3.9 million
bpd of capacity) with another 30 in various stages of design, construc-
tion and commissioning.
Efficiency/product quality: Commercial onstream efciencies of more
than 95% are routinely achieved in CCR Platforming units.
Licensor: UOP LLC.

Coking
Application: Conversion of vacuum residues (virgin and hydrotreated),
various petroleum tars and coal tar pitch through delayed coking.
Products: Fuel gas, LPG, naphtha, gas oils and fuel, anode or needle
grade coke (depending on feedstock and operating conditions).
Description: Feedstock is introduced (after heat exchange) to the bot-
tom of the coker fractionator (1) where it mixes with condensed recycle.
The mixture is pumped through the coker heater (2) where the desired
coking temperature is achieved, to one of two coke drums (3). Steam
or boiler feedwater is injected into the heater tubes to prevent coking in
the furnace tubes. Coke drum overhead vapors ow to the fractionator
(1) where they are separated into an overhead stream containing the
wet gas, LPG and naphtha; two gas oil sidestreams; and the recycle that
rejoins the feed.
The overhead stream is sent to a vapor recovery unit (4) where the
individual product streams are separated. The coke that forms in one of
at least two (parallel connected) drums is then removed using high-pres-
sure water. The plant also includes a blow-down system, coke handling
and a water recovery system.
Heater outlet temperature, F 900950
Coke drum pressure, psig 1590
Recycle ratio, vol/vol feed, % 0100
Yields:
Vacuum residue of
Middle East hydrotreated Coal tar
Feedstock vac. residue bottoms pitch
Gravity, API 7.4 1.3 211.0
Sulfur, wt% 4.2 2.3 0.5
Conradson
carbon, wt% 20.0 27.6
Products, wt%
Gas + LPG 7.9 9.0 3.9
Naphtha 12.6 11.1
Gas oils 50.8 44.0 31.0
Coke 28.7 35.9 65.1
Economics:
Investment (basis: 20,000 bpsd straight-run vacuum residue feed,
US Gulf Coast 2002, fuel-grade coke, includes vapor recovery), US$
per bpsd (typical) 4,000

Continued
Economics (continued):
Utilities, typical/bbl of feed:
Fuel, 10
3
Btu 145
Steam (exported), lb 20
Water, cooling, gal 180
Installation: More than 55 units.
Reference: Mallik, Ram, Gary and Hamilton, Delayed coker design con-
siderations and project execution, NPRA 2002 Annual Meeting, March
1719, 2002.
Licensor: ABB Lummus Global.
Coking, continued
Coking
Application: Upgrading of petroleum residues (vacuum residue, bitumen,
solvent-deasphalter pitch and fuel oil) to more valuable liquid products
(LPG, naphtha, distillate and gas oil). Fuel gas and petroleum coke are
also produced.
Description: The delayed coking process is a thermal process and con-
sists of red heater(s), coke drums and main fractionator. The cracking
and coking reactions are initiated in the red heater under controlled
time-temperature-pressure conditions. The reactions continue as the
process stream moves to the coke drums. Being highly endothermic,
the coking-reaction rate drops dramatically as coke-drum temperature
decreases. Coke is deposited in the coke drums. The vapor is routed to
the fractionator, where it is condensed and fractionated into product
streamstypically fuel gas, LPG, naphtha, distillate and gas oil.
When one of the pair of coke drums is full of coke, the heater outlet
stream is directed to the other coke drum. The full drum is taken ofine,
cooled with steam and water and opened. The coke is removed by hy-
draulic cutting. The empty drum is then closed, warmed-up and made
ready to receive feed while the other drum becomes full.
Benets of ConocoPhillips delayed coking technology are:
Maximum liquid-product yields and minimum coke yield through
low-pressure operation, patented distillate recycle technology and zero
(patented) or minimum natural recycle operation
Maximum exibility; distillate recycle operation can be used to
adjust the liquid-product slate or can be withdrawn to maximize unit
capacity
Extended furnace runlengths between decokings
Ultra-low-cycle-time operation maximizes capacity and asset uti-
lization
Higher reliability and maintainability enables higher onstream time
and lowers maintenance costs
Lower investment cost.
Economics: For a delayed coker processing 35,000 bpsd of heavy, high-
sulfur vacuum residue, the U.S. Gulf Coast investment cost is approxi-
mately U.S.$145160 million.
Installation: Low investment cost and attractive yield structure has made
delayed coking the technology of choice for bottom-of-the-barrel up-
grading. Numerous delayed coking units are operating in petroleum re-
neries worldwide.

Coking
Application: Manufacture petroleum coke and upgrade residues to
lighter hydrocarbon fractions using the Selective Yield Delayed Coking
(SYDEC) process.
Products: Coke, gas, LPG, naphtha and gas oils.
Description: Charge is fed directly to the fractionator (1) where it
combines with recycle and is pumped to the coker heater where it is
heated to coking temperature, causing partial vaporization and mild
cracking. The vapor-liquid mix enters a coke drum (2 or 3) for further
cracking. Drum overhead enters the fractionator (1) to be separated
into gas, naphtha, and light and heavy gas oils. There are at least two
coking drums, one coking while the other is decoked using high-pres-
sure water jets.
Operating conditions: Typical ranges are:
Heater outlet temperature, F 900950
Coke drum pressure, psig 15100
Recycle ratio, equiv. fresh feed 0.051.0
Increased coking temperature decreases coke production; increas-
es liquid yield and gas oil end point. Increasing pressure and/or recycle
ratio increases gas and coke make, decreases liquid yield and gas oil
end point.
Yields:
Operation: Max dist. Anode coke Needle coke
products, wt%
Gas 8.7 8.4 9.8
Naphtha 14.0 21.6 8.4
Gas oil 48.3 43.8 41.6
Coke 29.3 26.2 40.2
Economics:
Investment (basis: 65,00010,000 bpsd,
2Q 2004, US Gulf), $ per bpsd 2,7505,000
Utilities, typical per bbl feed:
Fuel, 10
3
Btu 120
Electricity, kWh 3
Steam (exported), lb 35
Water, cooling, gal 36
Installation: More than 65,000 tpd of fuel, anode and needle coke.
References: Handbook of Petroleum Rening Processes, 3rd Ed., pp.
12.3312.89.

Continued
Optimize coker operations, Hydrocarbon Processing, September
2003.
Delayed coking revamps, Hydrocarbon Processing, September
2004.
Drivers for additional delayed coking capacity in the rening indus-
try, Petroleum Economist, September 2003.
Licensor: Foster Wheeler/UOP LLC.
Coking, continued
Coking, flexi
Application: Continuous uid bed technology to convert heavy hydrocarbons
(vacuum residuum, extra heavy oil or bitumen) to full-range lighter liquid
products and low-Btu fuel gas. Applicable for resid conversion in reneries
with limited outlets for coke, for heavy feed conversion at the resource loca-
tion and for producing a fuel substitute where natural gas has high value.
Products: Liquid and gas products can be upgraded through conven-
tional treating. Low-Btu gas created from gasication of coke can be
burned in furnaces or boilers, replacing other fuels at reneries or up-
stream production facilities.
Description: FLEXICOKING has essentially the same reactor (1)/scrubber
(2) sections as FLUID COKING, and also has the same process exibility
options: recycle, once-through and VPS integrated.
Process heat is supplied by circulating hot coke between the heater
(3) and reactor. Coke reacts with air and steam in the gasier (4) to
produce heat and low-Btu gas that can be used as fuel in furnaces and
boilers, backing out fuel gas. About 97% of the coke generated is con-
sumed in the process; a small amount of coke is withdrawn from the
heater (3) and nes system (5), which can be disposed in cement kilns
or used in metals recovery. Partial gasication and oxygen-enrichment
can be used to provide additional process exibility. A dual-gasication
option can produce a hydrogen-rich stream.
Yields: Example, typical Middle East vacuum resid (~ 25 wt% Concar-
bon, ~5 wt% sulfur):
Recycle Once-through
Light ends, wt% 11.8 10.4
Naphtha (C
5
, 350F), wt% 11.5 9.5
Distillate (350 650F), wt% 14.5 13.1
Heavy gas oil (650F+), wt% 32.1 39.7
Low-Btu gas, MBtu/bbl 1.2 1.1
C
5
+ Liquids, wt% 58.1 62.3
Investment: TPC, US Gulf Coast, 2Q 2003 estimate with all environmen-
tal controls included (range dependent on unit capacity)
Capital investment, $/bpsd 3,000 4,700
Competitive advantages:
Fully continuous, commercially proven uid-bed coking and uid
bed gasication process that is internally fueled and heat inte-
grated with no purchase of fuel gas.
Low-value coke is converted to fuel gas for use onsite or sale.
Processes wide range of feeds, especially high metals, sulfur, CCR
and single-train capacities >100 Kbpsd
Continued technology developments providing enhancements for
yields, capacity, reliability and run length
More cost effective than delayed coking-partial oxidation or direct
gasication of heavy feeds.
Continued
Coking, flexi, continued
Coking, fluid
Application: Continuous uid bed technology to convert heavy hydro-
carbons (vacuum residuum, extra heavy oil or bitumen) to full-range
lighter liquid products and coke. Coke can be sold as fuel or burned in
an integrated uid bed boiler to produce power and steam.
Products: Liquid and gas products can be upgraded through conven-
tional treating. Fluid coke is widely used as a solid fuel, with particular
advantages in cement kilns and in uid bed boilers.
Description: Feed (typically 1,050F+ vacuum resid) enters the scrubber
(1) for heat exchange with reactor overhead efuent vapors. The scrub-
ber typically cuts 975F+ higher boiling reactor efuent hydrocarbons
for recycle back to the reactor with fresh feed. Alternative scrubber con-
gurations provide process exibility by integrating the recycle stream
with the VPS or by operating once-through, which produces higher liq-
uid yields. Lighter overhead vapors from the scrubber are sent to con-
ventional fractionation and light ends recovery. In the reactor (2), feed is
thermally cracked to a full-range of lighter products and coke.
The heat for the thermal cracking reactions is supplied by circulat-
ing coke between the burner (3) and reactor. About 20% of the coke
is burned with air to supply process heat requirements, eliminating the
need for an external fuel supply. The rest of the coke is withdrawn and
either sold as a product or burned in a uid bed boiler. Properties of the
uid coke enable ease of transport and direct use in fuel applications,
including stand-alone or integrated cogeneration facilities.
Yields: Example, typical Middle East vacuum resid (~25 wt% Concar-
bon, ~5 wt% sulfur):
Recycle Once-through
Light ends, wt% 11.8 10.4
Naphtha (C
5
, 350F), wt% 11.5 9.5
Distillate (350650F), wt% 14.5 13.1
Heavy Gas Oil (650F+), wt% 32.1 39.7
Net product coke, wt% 25.7 23.9
Coke consumed for heat, wt% 4.4 3.4
C
5
+ liquids, wt% 58.1 62.3
Investment: TPC, U.S. Gulf Coast, 2Q03 estimate with all environmental
controls included (range dependent on unit capacity)
Capital investment, $/bp/sd 2,2003,600
Competitive advantages:
Fully continuous commercially proven uid-bed coking process
Single-train capacities >100 KB/SD; greater than other processes
Process wide range of feeds, especially high metals, sulfur, CCR
Internally heat integrated, minimal purchase of fuel gas; lower
coke production than delayed coking

Continued
Continued technology developments (yields, run length, reliability)
Lower investment and better economy of scale than delayed
coking
Efcient integration with uid bed boilers for COGEN.
Coking, fluid, continued
Crude distillation
Application: Separates and recovers the relatively lighter fractions from a
fresh crude oil charge (e.g., naphtha, kerosine, diesel and cracking stock).
The vacuum asher processes the crude distillation bottoms to produce
an increased yield of liquid distillates and a heavy residual material.
Description: The charge is preheated (1), desalted (2) and directed to a
preheat train (3) where it recovers heat from product and reux streams.
The typical crude red heater (4) inlet temperature is on the order of
550 F, while the outlet temperature is on the order of 675F to 725F.
Heater efuent then enters a crude distillation column (5) where light
naphtha is drawn off the tower overhead (6); heavy naphtha, kerosine,
diesel and cracking stock are sidestream drawoffs. External reux for
the tower is provided by pumparound streams (710). The atmospheric
residue is charged to a red heater (11) where the typical outlet tem-
perature is on the order of 750 F to 775F.
From the heater outlet, the stream is fed into a vacuum tower (12),
where the distillate is condensed in two sections and withdrawn as two
sidestreams. The two sidestreams are combined to form cracking feed-
stock. An asphalt base stock is pumped from the bottom of the tower.
Two circulating reux streams serve as heat removal media for the tower.
Yields: Typical for Merey crude oil:
Crude unit products wt% API Pour, F
Overhead & naphtha 6.2 58.0
Kerosine 4.5 41.4 85
Diesel 18.0 30.0 10
Gas oil 3.9 24.0 20
Lt. vac. gas oil 2.6 23.4 35
Hvy. vac. gas oil 10.9 19.5 85
Vac. bottoms 53.9 5.8 (120)*
Total 100.0 8.7 85
*Softening point, F
Note: Crude unit feed is 2.19 wt% sulfur. Vacuum unit feed is 2.91 wt% sulfur.
Economics:
Investment ( basis: 100,00050,000 bpsd,
2nd Q, 2004, US Gulf ), $ per bpsd 800 1,180
Utility requirements, typical per bbl fresh feed
Steam, lb 24
Fuel (liberated), 10
3
Btu ( 80 120 )
Power, kWh 0.6
Water, cooling, gal 300 400
Installation: Foster Wheeler has designed and constructed crude units
having a total crude capacity in excess of 15 MMbpsd.
Continued
Reference: Encyclopedia of Chemical Processing and Design, Marcel-
Dekker, 1997, pp. 230 249.
Licensor: Foster Wheeler.
Crude distillation, continued
Crude distillation
Application: The Shell Bulk CDU is a highly integrated concept. It sepa-
rates the crude in long residue, waxy distillate, middle distillates and a
naphtha minus fraction. Compared with stand-alone units, the overall
integration of a crude distillation unit (CDU), hydrodesulfurization unit
(HDS), high vacuum unit (HVU) and a visbreaker (VBU) results in a 50%
reduction in equipment count and signicantly reduced operating costs.
A prominent feature embedded in this design is the Shell deepash HVU
technology. This technology can also be provided in cost-effective pro-
cess designs for both feedprep and lube oil HVUs as stand-alone units.
For each application, tailor-made designs can be produced.
Description: The basic concept of the bulk CDU is the separation of the
naphtha minus and the long residue from the middle distillate fraction,
which is routed to the HDS. After desulfurization in the HDS unit, nal
product separation of the bulk middle distillate stream from the CDU
takes place in the HDS fractionator (HDF), which consists of a main at-
mospheric fractionator with side strippers.
The long residue is routed hot to a feedprep HVU, which recov-
ers the waxy distillate fraction from long residue as the feedstock for
a cat-cracker or hydrocracker unit (HCU). Typical ashzone conditions
are 415C and 24 mbara. The Shell design features a deentrainment
section, spray sections to obtain a lower ashzone pressure, and a VGO
recovery section to recover up to 10 wt% as automotive diesel. The Shell
furnace design prevents excessive cracking and enables a 5-year run
length between decoke.
Yields: Typical for Arabian light crude
Products wt, %
Gas C
1
C
4
0.7
Gasoline C
5
150C 15.2
Kerosine 150 250C 17.4
Gasoil (GO) 250 350C 18.3
VGO 350 370C 3.6
Waxy distillate (WD) 370 575C 28.8
Residue 575C+ 16.0
Economics: Due to the incorporation of Shell high capacity internals
and the deeply integrated designs, an attractive CAPEX reduction can be
achieved. Investment costs are dependent on the required conguration
and process objectives.
Installation: Over 100 Shell CDUs have been designed and operated
since the early 1900s. Additionally, a total of some 50 HVU units have
been built while a similar number has been debottlenecked, including
many third-party designs of feedprep and lube oil HVUs.
Licensor: Shell Global Solutions International B.V.
Crude distillation
Application: The D2000 process is progressive distillation to minimize
the total energy consumption required to separate crude oils or con-
densates into hydrocarbon cuts, which number and properties are opti-
mized to t with sophisticated rening schemes and future regulations.
This process is applied normally for new topping units or new integrated
topping/vacuum units but the concept can be used for debottlenecking
purpose.
Products: This process is particularly suitable when more than two
naphtha cuts are to be produced. Typically the process is optimized to
produce three naphtha cuts or more, one or two kerosine cuts, two at-
mospheric gas oil cuts, one vacuum gas oil cut, two vacuum distillates
cuts, and one vacuum residue.
Description: The crude is preheated and desalted (1). It is fed to a rst
dry reboiled pre-ash tower (2) and then to a wet pre-ash tower (3).
The overhead products of the two pre-ash towers are then fraction-
ated as required in a gas plant and rectication towers (4).
The topped crude typically reduced by
2
/3 of the total naphtha cut is
then heated in a conventional heater and conventional topping column
(5). If necessary the reduced crude is fractionated in one deep vacuum
column designed for a sharp fractionation between vacuum gas oil, two
vacuum distillates (6) and a vacuum residue, which could be also a road
bitumen.
Extensive use of pinch technology minimizes heat supplied by heat-
ers and heat removed by air and water coolers.
This process is particularly suitable for large crude capacity from
150,000 to 250,000 bpsd.
It is also available for condensates and light crudes progressive distil-
lation with a slightly adapted scheme.
Economics:
Investment (basis 230,000 bpsd including atmospheric and
vacuum distillation, gas plant and rectication tower) 750 to
950 $ per bpsd (US Gulf Coast 2000).
Utility requirements, typical per bbl of crude feed:
Fuel red, 10
3
btu 5065
Power, kWh 0.91.2
Steam 65 psig, lb 05
Water cooling, (15C rise) gal 50100
Total primary energy consumption:
for Arabian Light or Russian Export Blend: 1.25 tons of fuel
per 100 tons of Crude
for Arabian Heavy 1.15 tons of fuel
per 100 tons of Crude

Continued
Installation: Technip has designed and constructed one crude unit and
one condensate unit with the D2000 concept. The latest revamp proj-
ect currently in operation shows an increase of capacity of the existing
crude unit of 30% without heater addition.
Licensor: TOTALFINAELF and Technip.
Crude distillation, continued
Crude topping units
Application: Crude topping units are typically installed in remote areas
to provide fuel for local consumption, often for use at pipeline pumping
stations and at production facilities.
Products: Diesel is typically the desired product, but kerosine, turbine
fuel and naphtha are also produced.
Description: Crude topping units comprise of four main sections: pre-
heat/heat recovery section, red heater, crude fractionation (distillation),
and product cooling and accumulation. The red heater provides heat
for the plant. Fuel for the heater can be residual products, offgas, natural
gas, distillate product, or combinations of these fuels, depending on the
installation. Heat integration reduces emissions and minimizes process-
energy requirements. Depending on the individual site, an electrostatic
desalter may or may not be required to prevent fouling and plugging,
and control corrosion in the fractionation section.
Crude topping units are modularized, which reduces construction
cost and complexity. Modular units also allow installation in remote ar-
eas with minimal mobilization. These units are typically custom designed
to meet individual customer requirements.
Crude topping units are self-contained, requiring few utilities for opera-
tion. Utility packages, wastewater treatment facilities and other associated
offsites are often supplied, depending on the individual site requirements.
Column pressure, psig 0 20
Temperature, F 550 650

Deasphalting
Application: Prepare quality feed for FCC units and hydrocrackers from
vacuum residue and blending stocks for lube oil and asphalt manufac-
turing.
Products: Deasphalted oil (DAO) for catalytic cracking and hydrocracking
feedstocks, resins for specication asphalts, and pitch for specication
asphalts and residue fuels.
Description: Feed and light parafnic solvent are mixed then charged to
the extractor (1). The DAO and pitch phases, both containing solvents,
exit the extractor. The DAO and solvent mixture is separated under su-
percritical conditions (2). Both the pitch and DAO products are stripped
of entrained solvent (3,4). A second extraction stage is utilized if resins
are to be produced.
Operating conditions: Typical ranges are: solvent, various blends of C
3
C
7
hydrocarbons including light naphthas. Pressure: 300 to 600 psig.
Temp.: 120F to 450F. Solvent-to-oil ratio: 4/1 to 13/1.
Yields:
Feed, type Lube oil Cracking stock
Sulfur, wt% 4.9 3.0
CCR, wt% 20.1 21.8
Visc, SSU@ 210F 7,300 8,720
Ni/V, wppm 29/100 46/125
DAO
Yield, vol.% of Feed 30 53 65
Gravity, API 20.3 17.6 15.1
Sulfur, wt% 2.7 1.9 2.2
CCR, wt% 1.4 3.5 6.2
Visc., SSU@ 210F 165 307 540
Ni/V, wppm 0.25/0.37 1.8/3.4 4.5/10.3
Pitch
Softening point, R&B,F 149 226 240
Penetration@77F 12 0 0
Economics:
Investment (basis: 2,00040,000 bpsd
2Q 2004, US Gulf), $/bpsd 8003,000
Utilities, typical per bbl feed: Lube oil Cracking stock
Fuel, 10
3
Btu 81 56
Electricity, kWh 1.5 1.8
Steam, 150-psig, lb 116 11
Water, cooling (25F rise), gal 15 nil
Continued
Installations: 50+. This also includes both UOP and Foster Wheeler units
originally licensed separately before merging the technologies in 1996.
Reference: Handbook of Petroleum Rening Processes, 2nd Ed., Mc-
Graw Hill, 1997, pp.10.1510.60.
Licensor: UOP LLC/Foster Wheeler.
Deasphalting, continued
Deasphalting
Application: Extract lubricating oil blend stocks and FCCU or hydrocracker
feedstocks with low metal and Conradson carbon contents from atmo-
spheric and vacuum resid using ROSE Supercritical Fluid Technology. Can
be used to upgrade existing solvent deasphalters. ROSE may also be
used to economically upgrade heavy crude oil.
Products: Lube blend stocks, FCCU feed, hydrocracker feed, resins and
asphaltenes.
Description: Resid is charged through a mixer (M-1), where it is mixed
with solvent before entering the asphaltene separator (V-1). Counter-
current solvent ow extracts lighter components from the resid while
rejecting asphaltenes with a small amount of solvent. Asphaltenes are
then heated and stripped of solvent (T-1). Remaining solvent solution
goes overhead (V-1) through heat exchange (E-1) and a second separa-
tion (V-2), yielding an intermediate product (resins) that is stripped of
solvent (T-2). The overhead is heated (E-4, E-6) so the solvent exists as
a supercritical uid in which the oil is virtually insoluble. Recovered sol-
vent leaves the separator top (V-3) to be cooled by heat exchange (E-4,
E-1) and a cooler (E-2). Deasphalted oil from the oil separator (V-3) is
stripped (T-3) of dissolved solvent. The only solvent vaporized is a small
amount dissolved in fractions withdrawn in the separators. This solvent
is recovered in the product strippers. V-1, V-2 and V-3 are equipped with
high-performance ROSEMAX internals. These high-efciency, high-ca-
pacity internals offer superior product yield and quality while minimiz-
ing vessel size and capital investment. They can also debottleneck and
improve operations of existing solvent deasphalting units.
The system can be simplied by removing equipment in the outlined
box to make two products. The intermediate fraction can be shifted
into the nal oil fraction by adjusting operating conditions. Only one
exchanger (E-6) provides heat to warm the resid charge and the small
amount of extraction solvent recovered in the product strippers.
Yields: The extraction solvent composition and operating conditions are
adjusted to provide the product quality and yields required for down-
stream processing or to meet nished product specications. Solvents
range from propane through hexane and include blends normally pro-
duced in reneries.
Economics:
Investment: (Basis: 30,000 bpsd, US Gulf Coast),
$ per bpsd 1,250
Fuel absorbed, 10
3
Btu 80110
Steam, 150-psig, lb 12
Installation: Thirty-six licensed units with a combined capacity of over

600,000 bpd.
Reference: Northup, A. H., and H. D. Sloan, Advances in solvent deas-
phalting technology, 1996 NPRA Annual Meeting, San Antonio.
Licensor: Kellogg Brown & Root, Inc.
Deasphalting, continued
Deep catalytic cracking
Application: Selective conversion of gasoil and parafnic residual feed-
stocks.
Products: C
2
C
5
olens, aromatic-rich, high-octane gasoline and
distillate.
Description: DCC is a uidized process for selectively cracking a wide
variety of feedstocks to light olens. Propylene yields over 24 wt% are
achievable with parafnic feeds. A traditional reactor/regenerator unit
design uses a catalyst with physical properties similar to traditional FCC
catalyst. The DCC unit may be operated in two operational modes: max-
imum propylene (Type I) or maximum iso-olens (Type II).
Each operational mode utilizes unique catalyst as well as reaction
conditions. Maximum propylene DCC uses both riser and bed cracking
at severe reactor conditions while Type II DDC uses only riser cracking
like a modern FCC unit at milder conditions.
The overall ow scheme of DCC is very similar to that of a conven-
tional FCC. However, innovations in the areas of catalyst development,
process variable selection and severity and gas plant design enables
the DCC to produce signicantly more olens than FCC in a maximum
olens mode of operation.
This technology is quite suitable for revamps as well as grassroot
applications. Feed enters the unit through proprietary feed nozzles, as
shown in the schematic. Integrating DCC technology into existing ren-
eries as either a grassroots or revamp application can offer an attractive
opportunity to produce large quantities of light olens.
In a market requiring both proplylene and ethylene, use of both
thermal and catalytic processes is essential, due to the fundamental
differences in the reaction mechanisms involved. The combination of
thermal and catalytic cracking mechanisms is the only way to increase
total olens from heavier feeds while meeting the need for an increased
propylene to ethylene ratio. The integrated DCC/steam cracking com-
plex offers signicant capital savings over a conventional stand-alone
renery for propylene production.
Products (wt% of fresh feed) DCC Type I DCC Type II FCC
Ethylene 6.1 2.3 0.9
Propylene 20.5 14.3 6.8
Butylene 14.3 14.6 11.0
in which IC
4
=
5.4 6.1 3.3
Amylene 9.8 8.5
in which IC
5
=
6.5 4.3
Installation: Six units are currently operating in China and one in Thai-
land. Several more units are under design in China.
Reference: Dharia, D., et al., Increase light olens production, Hydro-
carbon Processing, April 2004, pp. 6166.

Continued
Licensor: Stone & Webster Inc., a Shaw Group Co., and Research Insti-
tute of Petroleum Processing, Sinopec.
Deep catalytic cracking, continued
Deep thermal conversion
Application: The Shell Deep Thermal Conversion process closes the gap
between visbreaking and coking. The process yields a maximum of distil-
lates by applying deep thermal conversion of the vacuum residue feed
and by vacuum ashing the cracked residue. High-distillate yields are
obtained, while still producing a stable liquid residual product, referred
to as liquid coke. The liquid coke, not suitable for blending to commer-
cial fuel, is used for speciality products, gasication and/or combustion,
e.g., to generate power and/or hydrogen.
Description: The preheated short residue is charged to the heater (1)
and from there to the soaker (2), where the deep conversion takes place.
The conversion is maximized by controlling the operating temperature
and pressure. The soaker efuent is routed to a cyclone (3). The cyclone
overheads are charged to an atmospheric fractionator (4) to produce the
desired products like gas, LPG, naphtha, kero and gasoil. The cyclone
and fractionator bottoms are subsequently routed to a vacuum asher
(5), which recovers additional gasoil and waxy distillate. The residual liq-
uid coke is routed for further processing depending on the outlet.
Yields: Depend on feed type and product specications.
Feed, vacuum residue Middle East
Viscosity, cSt @100C 770
Products in % wt. on feed
Gas 4.0
Gasoline ECP 165C 8.0
Gas oil ECP 350C 18.1
Waxy distillate ECP 520C 22.5
Residue ECP 520C+ 47.4
Economics: The investment ranges from 1,300 to 1,600 US$/bbl in-
stalled excl. treating facilities and depending on the capacity and con-
guration (basis: 1998).

Utilities, typical per bbl @180C
Fuel, Mcal 26
Steam, net production, kg 20
Water, cooling, m
3
0.15
Installation: Presently, four Deep Thermal Conversion units have been
licensed. In two cases, this involved a revamp of an existing Shell Soaker
Visbreaker unit. In addition, two units are planned for revamp, while
one grassroots unit is currently under construction. Post startup services
and technical services on existing units are available from Shell.
Reference: Visbreaking Technology, Erdl and Kohle, January 1986.
Licensor: Shell Global Solutions International B.V. and ABB Lummus
Global B.V.
Desulfurization
Application: GT-DeSulf addresses overall plant protability by desulfur-
izing the FCC stream with no octane loss and decreased hydrogen con-
sumption by using a proprietary solvent in an extractive distillation sys-
tem. This process also recovers valuable aromatics compounds.
Description: FCC gasoline, with endpoint up to 210 C, is fed to the GT-
DeSulf unit, which extracts sulfur and aromatics from the hydrocarbon
stream. The sulfur and aromatic components are processed in a conven-
tional hydrotreater to convert the sulfur into H
2
S. Because the portion
of gasoline being hydrotreated is reduced in volume and free of olens,
hydrogen consumption and operating costs are greatly reduced. In con-
trast, conventional desulfurization schemes process the majority of the
gasoline through hydrotreating and caustic-washing units to eliminate
the sulfur. That method inevitably results in olen saturation, octane
downgrade and yield loss.
GT-DeSulf has these advantages:
Segregates and eliminates FCC-gasoline sulfur species to meet a
pool gasoline target of 20 ppm
Preserves more than 90% of the olens from being hydrotreated
in the HDS unit; and thus, prevents signicant octane loss and
reduces hydrogen consumption
Fewer components are sent to the HDS unit; consequently, a
smaller HDS unit is needed and there is less yield loss
High-purity BTX products can be produced from the aromatic-rich
extract stream after hydrotreating
Olen-rich rafnate stream (from the ED unit) can be recycled to
the FCC unit to increase the light olen production.
FCC gasoline is fed to the extractive distillation column (EDC). In a
vapor-liquid operation, the solvent extracts the sulfur compounds into
the bottoms of the column along with the aromatic components, while
rejecting the olens and nonaromatics into the overhead as rafnate.
Nearly all of the nonaromatics, including olens, are effectively sepa-
rated into the rafnate stream. The rafnate stream can be optionally
caustic washed before routing to the gasoline pool, or to a C
3
=
produc-
ing unit.
Rich solvent, containing aromatics and sulfur compounds, is routed
to the solvent recovery column, (SRC), where the hydrocarbons and sul-
fur species are separated, and lean solvent is recovered in columns bot-
toms. The SRC overhead is hydrotreated by conventional means and
used as desulfurized gasoline, or directed to an aromatics production
plant. Lean solvent from the SRC bottoms are treated and recycled back
to the EDC.
Economics: Estimated installed cost of $1,000 / bpd of feed and produc-
tion cost of $0.50 / bbl of feed for desulfurization and dearomatization.
Desulfurization
Application: The S-Brane process selectively separates sulfur from gaso-
line streams by using a membrane technology. This method can be used
to meet clean-gasoline requirements with minimal octane loss. S-Brane
also substantially reduces the reners need to hydrotreat naphtha.
Products: A low-sulfur stream (typically 80% of the feed) that can be di-
rectly blended into a gasoline pool and a small stream with concentrated
sulfur that requires further processing.
Description: S-Brane is a simple physical separation process that sepa-
rates a feed gasoline stream into two product streams. The feed stream
(ideally a C
5
-350F FCC gasoline stream) is passed over a membrane
that is selective for sulfur-containing hydrocarbon molecules. As the gas-
oline passes over the membrane, sulfur-containing molecules and some
hydrocarbon molecules dissolve into the membrane and, subsequently,
diffuse through it. A low-sulfur stream (retentate), about 7580% of the
inlet gasoline volume, can be directly blended into the gasoline pool.
A smaller stream (permeate) contains the majority of the sulfur
and must be processed further before being blended into the gasoline
pool.
S-Brane operates as a pervaporation-mode-membrane process. The
driving force that moves molecules through the membrane is a vacuum
on the backside (permeate side) of the membrane that causes a vapor
pressure gradient for each molecule type.
The shell side of the assembly is operated under vacuum conditions
(about 0.751.5 psia). Once through the membrane, permeate mole-
cules are condensed and passed along for further processing to treat the
now concentrated sulfur species. In the S-Brane process, the feed and
retentate are at about 230F and 100 psig while the permeate is rst a
vapor and then condensed into liquid form.
The process provides an effective way to reduce reners hydrotreat-
ing requirements and substantially avoid octane loss associated with hy-
drotreating-based technologies.
Economics: The capital cost of S-Brane is about 30% of a correspond-
ing size hydrotreating unit. The exact number is dependent on both the
processing capacity and also the sulfur levels of both the feed and the
desired product.
Membrane service-life: 3 years
Catalyst: None
Hydrogen requirement: None
Utilities (per bbl feed)
Electricity 0.91 kW
Water, cooling (20F rise) 128 gal
Steam, 50 lb 9.3 lbs
Steam, 300 lb 5.1 lbs
Continued
Installation: A 300-bpd demonstration plant has been in operation since
June 2003.
Reference: S-BraneTechnology Brings Flexibility To Reners Clean
Fuels Solutions, 2004 NPRA Annual Meeting, San Antonio, March
2223, 2004.
Licensor: W. R. Grace & Co.
Desulfurization, continued
Dewaxing
Application: Bechtels Dewaxing process is used to remove waxy com-
ponents from lubrication base-oil streams to simultaneously meet de-
sired low-temperature properties for dewaxed oils and produce slack
wax as a byproduct.
Description: Waxy feedstock (rafnate, distillate or deasphalted oil) is
mixed with a binary-solvent system and chilled in a very closely controlled
manner in scraped-surface double-pipe exchangers (1) and refrigerated
chillers (2) to form a wax/oil/solvent slurry.
The slurry is ltered through the primary lter stage (3) and dewaxed
oil mixture is routed to the dewaxed oil recovery section (5) to separate
solvent from oil. Prior to solvent recovery, the primary ltrate is used to
cool the feed/solvent mixture (1). Wax from the primary stage is slurried
with cold solvent and ltered again in the repulp lter (4) to reduce the
oil content to approximately 10%.
The repulp ltrate is reused as dilution solvent in the feed chilling
train. The wax mixture is routed to a solvent-recovery section (6) to re-
move solvent from the product streams (hard wax and soft wax). The
recovered solvent is collected, dried (7) and recycled back to the chilling
and ltration sections.
Economics:
Investment (Basis: 7,000-bpsd feedrate
capacity, 2004 US Gulf Coast), $/bpsd 9,300
Fuel, 10
3
Btu (absorbed) 160
Electricity, kWh 15
Steam, lb 35
Water, cooling (25F rise), gal 1,100
Installation: Over 100 have been licensed and built.
Licensor: Bechtel Corp.
Dewaxing
Application: Selectively convert feedstocks waxy molecules by isomeriza-
tion in the presence of ISODEWAXING Catalysts. The products are high-
quality base oils that can meet stringent cold ow properties.
Description: ISODEWAXING Catalysts are very special catalysts that con-
vert feedstocks with waxy molecules (containing long, parafnic chains)
into two or three main branch isomers that have low-pour points. The
product also has low aromatics content. Typical feeds are: rafnates,
slack wax, foots oil, hydrotreated VGO, hydrotreated DAO and uncon-
verted oil from hydrocracking.
As shown in the simplied ow diagram, waxy feedstocks are mixed
with recycle hydrogen and fresh makeup hydrogen, heated and charged
to a reactor containing ISODEWAXING Catalyst (1). The efuent will
have a much lower pour point and, depending on the operating severity,
the aromatics content is reduced by 50 80% in the dewaxing reactor.
In a typical conguration, the efuent from a dewaxing reactor is
cooled down and sent to a nishing reactor (2) where the remaining
single ring and multiple ring aromatics are further saturated by the ISO-
FINISHING Catalysts. The efuent is ashed in high-pressure and low-
pressure separators (3, 4). Small amounts of light products are recovered
in a fractionation system (5).
Yields: The base oil yields strongly depend on the feedstocks. For a typi-
cal low wax content feedstock, the base oil yield can be 9095%. Higher
wax feed will have a little lower base oil yield.
Economics:
Investment: This is a moderate investment process; for a typical size
ISODEWAXING/ISOFINISHING Unit, the capital for ISBL
is about 6,000 $/bpsd.
Utilities: Typical per bbl feed:
Power, kW 3.3
Fuel , kcal 13.4 x 10
3
Steam, superheated, required, kg 5.3
Steam, saturated, produced, kg 2.4
Water, cooling, kg 192
Chemical-hydrogen consumption, Nm
3
/m
3
oil 30~50
Installation: Ten units are in operation and eight units are in various
stages of design or construction.
Reference: NPRA Annual Meeting, March 2004, San Antonio, Paper
AM-04-68.
Licensor: Chevron Lummus Global LLC.
Dewaxing/wax deoiling
Application: Bechtels Dewaxing/Wax Fractionation processes are used
to remove waxy components from lubrication base-oil streams to si-
multaneously meet desired low-temperature properties for dewaxed oils
and produce hard wax as a premium byproduct.
Description: Bechtels two-stage solvent dewaxing process can be ex-
panded to simultaneously produce hard wax by adding a third deoiling
stage using the Wax Fractionation process. Waxy feedstock (rafnate,
distillate or deasphalted oil) is mixed with a binary-solvent system and
chilled in a very closely controlled manner in scraped-surface double-
pipe exchangers (1) and refrigerated chillers (2) to form a wax/oil/solvent
slurry.
The slurry is ltered through the primary lter stage (3) and dewaxed
oil mixture is routed to the dewaxed oil recovery section (6) to separate
solvent from oil. Prior to solvent recovery, the primary ltrate is used to
cool the feed/solvent mixture (1).
Wax from the primary stage is slurried with cold solvent and ltered
again in the repulp lter (4) to reduce the oil content to approximately
10%. The repulp ltrate is reused as dilution solvent in the feed chilling
train. The low-oil content slack wax is warmed by mixing with warm
solvent to melt the low-melting-point waxes (soft wax) and is ltered in
a third stage ltration (5) to separate the hard wax from the soft wax.
The hard and soft wax mixtures are each routed to solvent recovery sec-
tions (7,8) to remove solvent from the product streams (hard wax and
soft wax). The recovered solvent is collected, dried (9) and recycled back
to the chilling and ltration sections.
Economics:
Fuel, 10
3
Btu (absorbed) 230
Electricity, kWh 25
Steam, lb 25
Installation: Seven in service.
Diesel upgrading
Application: Topses Diesel Upgrading process can be applied for im-
provement of a variety of diesel properties, including reduction of diesel
specic gravity, reduction of T90 and T95 distillation (Back-end-shift),
reduction of aromatics, and improvements of cetane, cold-ow prop-
erties, (pour point, clouds point, viscosity and CFPP) and diesel color
reduction (poly shift). Feeds can range from blends of straight-run and
cracked gas oils up to heavy distillates, including light vacuum gas oil.
Description: Topses Diesel Upgrading process is a combination of treating
and upgrading. The technology combines state-of-the-art reactor internals,
engineering expertise in quality design, high-activity treating catalyst and
proprietary diesel upgrading catalyst. Every unit is individually designed to
improve the diesel property that requires upgrading. This is done by select-
ing the optimum processing parameters, including unit pressure and LHSV
and determining the appropriate Topse high-activity catalysts. The pro-
cess is suitable for new units or revamps of existing hydrotreating units.
In the reactor system, the treating section uses Topses high-ac-
tivity CoMo or NiMo catalyst, such as TK-573 or TK-574, to remove
feed impurities such as sulfur and nitrogen. These compounds limit the
downstream upgrading catalyst performance, and the puried stream is
treated in the downstream upgrading reactor. Reactor catalyst used in
the application is dependent on the specic diesel property that requires
upgrading. Reactor section is followed by separation and stripping/frac-
tionation where nal products are produced.
Like the conventional Topse hydrotreating process, the diesel up-
grading process uses Topses graded-bed loading and high-efciency
patented reactor internals to provide optimal reactor performance and
catalyst utilization. Topses high-efciency internals are effective for a
wide range of liquid loading. Topses graded-bed technology and the
use of shape-optimized inert topping material and catalyst minimize
the pressure drop build-up, thereby reducing catalyst skimming require-
ments and ensuring long catalyst cycle lengths.
References: Patel, R., How are reners meeting the ultra-low-sulfur
diesel challenge? NPRA 2003 Annual Meeting, San Antonio, March
2003.
Fuente, E., P. Christensen, and M. Johansen, Options for meeting
EU year 2005 fuels specications, ERTC, November 1999.
Installations: A total of 13 units are in operation; ve in Asia-Pacic re-
gion, one in the Middle East, two in Europe and ve HDS/HDA units (see
Hydrodearomatization).

Dieselultra-low-sulfur diesel (ULSD)

Application: Topse ULSD process is designed to produce ultra-low-sul-
fur diesel (ULSD)550 wppm Sfrom cracked and straight-run dis-
tillates. By selecting the proper catalyst and operating conditions, the
process can be designed to produce 5 wppm S diesel at low reactor
pressures (<500 psig) or at higher reactor pressure when products with
improved density, cetane, and polyaromatics are required.
Description: Topse ULSD process is a hydrotreating process that com-
bines Topses understanding of deep-desulfurization kinetics, high-ac-
tivity catalyst, state-of-the-art reactor internal, and engineering exper-
tise in the design of new and revamped ULSD units. The ULSD process
can be applied over a very wide range of reactor pressures.
Our highest activity CoMo catalyst is specically formulated with
high-desulfurization activity and stability at low reactor pressure (~ 500
psig) to produce 5 wppm diesel. This catalyst is suitable for revamping
existing low-pressure hydrotreaters or in new units when minimizing
hydrogen consumption.
The highest activity NiMo catalyst is suitable at higher pressure when
secondary objectives such as cetane improvement and density reduction
are required. Topse offers a wide range of engineering deliverables to
meet the needs of the reners. Our offerings include process scoping
study, reactor design package, process design package, or engineering
design package.
Installation: Topse has licensed 34 ULSD hydrotreaters of which 26
units are designed for less than 10 wppm sulfur in the diesel. Our reac-
tor internals are installed in more than 60 units.
References: Cost-Effectively Improve Hydrotreater Designs, Hydrocar-
bon Processing, November 2001 pp. 4346.
The importance of good liquid distribution and proper selection of
catalyst for ultra deep diesel HDS, JPI Petroleum Rening Conference,
October 2000, Tokyo.
Low, G., J. Townsend, and T. Shooter, Systematic approach for the
revamp of a low-pressure hydrotreater to produce 10-ppm, sulfur-free
diesel at BP Conyton Renery, 7th ERTC, November 2002, Paris.
Electrical desalting
Application: For removal of undesirable impurities such as salt, water,
suspended solids and metallic contaminants from unrened crude oil,
residuums and FCC feedstocks.
Description: Salts such as sodium, calcium and magnesium chlorides
are generally contained in the residual water suspended in the oil phase
of hydrocarbon feedstocks. All feedstocks also contain, as mechanical
suspensions, such impurities as silt, iron oxides, sand and crystalline salt.
These undesirable components can be removed from hydrocarbon feed-
stocks by dissolving them in washwater or causing them to be water-
wetted. Emulsion formation is the best way to produce highly intimate
contact between the oil and washwater phases.
The electrical desalting process consists of adding process (wash)
water to the feedstock, generating an emulsion to assure maximum
contact and then utilizing a highly efcient AC electrical eld to resolve
the emulsion. The impurity - laden water phase can then be easily with-
drawn as underow.
Depending on the characteristics of the hydrocarbon feedstock be-
ing processed, optimum desalting temperatures will be in the range of
150 F to 300 F. For unrened crude feedstocks, the desalter is located in
the crude unit preheat train such that the desired temperature is achieved
by heat exchange with the crude unit products or pumparound reux.
Washwater, usually 3 6 vol%, is added upstream and / or downstream
of the heat exchanger(s). The combined streams pass through a mixing
device thereby creating a stable water - in - oil emulsion. Properties of the
emulsion are controlled by adjusting the pressure drop across the mixing
device.
The emulsion enters the desalter vessel where it is subjected to a
high - voltage electrostatic eld. The electrostatic eld causes the dis-
persed water droplets to coalesce, agglomerate and settle to the lower
portion of the vessel. The water phase, containing the various impurities
removed from the hydrocarbon feedstock, is continuously discharged to
the efuent system. A portion of the water stream may be recycled back
to the desalter to assist in water conservation efforts. Clean, desalted
hydrocarbon product ows from the top of the desalter vessel to subse-
quent processing facilities.
Desalting and dehydration efciency of the oil phase is enhanced by
using EDGE (Enhanced Deep-Grid Electrode) technology which creates
both high - and low - intensity AC electrical elds inside the vessel. De-
mulsifying chemicals may be used in small quantities to assist in oil / wa-
ter separation and to assure low oil contents in the efuent water.
Licensor: CB&I Howe - Baker Process and Technology.
Ethers
Application: Production of high-octane reformulated gasoline compo-
nents (MTBE, ETBE, TAME and/or higher molecular-weight ethers) from
C
1
to C
2
alcohols and reactive hydrocarbons in C
4
to C
6
cuts.
Description: Different arrangements have been demonstrated depend-
ing on the nature of the feeds. All use acid resins in the reaction section.
The process includes alcohol purication (1), hydrocarbon purication
(2), followed by the main reaction section. This main reactor (3) operates
under adiabatic upow conditions using an expanded-bed technology
and cooled recycle. Reactants are converted at moderate well-controlled
temperatures and moderate pressures, maximizing yield and catalyst life.
The main efuents are puried for further applications or recycle.
More than 90% of the total per pass conversion occurs in the ex-
panded-bed reactor. The efuent then ows to a reactive distillation
system (4), Catacol. This system, operated like a conventional distillation
column, combines catalysis and distillation. The catalytic zones of the
Catacol use xed-bed arrangements of an inexpensive acidic resin cata-
lyst that is available in bulk quantities and easy to load and unload.
The last part of the unit removes alcohol from the crude rafnate
using a conventional waterwash system (5) and a standard distillation
column (6).
Yields: Ether yields are not only highly dependent on the reactive olens
content and the alcohols chemical structure, but also on operating
goals: maximum ether production and/or high nal rafnate purity (for
instance, for downstream 1-butene extraction) are achieved.
Economics: Plants and their operations are simple. The same inexpen-
sive (purchased in bulk quantities) and long-lived, non-sophisticated cat-
alysts are used in the main reactor section catalytic region of the Catacol
column, if any.
Installation: Over 25 units, including ETBE and TAME, have been licensed.
Twenty-four units, including four Catacol units, are in operation.
Licensor: Axens.
Ethers
Application: To produce high-octane, low-vapor-pressure oxygenates
such as methyl tertiary butyl ether (MTBE), tertiary amyl methyl ether
(TAME) or heavier tertiary ethers for gasoline blending to reduce olen
content and/or meet oxygen/octane/vapor pressure specications. The
processes use boiling-point/tubular reactor and catalytic distillation
(CD) technologies to react methanol (MeOH) or ethanol with tertiary
isoolens to produce respective ethers.
Description: For an MTBE unit, the process can be described as follows.
Process description is similar for production of heavier ethers. The C
4
s
and methanol are fed to the boiling-point reactor (1)a xed-bed,
downow adiabatic reactor. In the reactor, the liquid is heated to its
boiling point by the heat of reaction, and limited vaporization occurs.
System pressure is controlled to set the boiling point of the reactor con-
tents and hence, the maximum temperatures. An isothermal tubular re-
actor is used, when optimum, to allow maximum temperature control.
The equilibrium-converted reactor efuent ows to the CD column (2)
where the reaction continues. Concurrently, MTBE is separated from un-
reacted C
4
s as the bottom product.
This scheme can provide overall isobutylene conversions up to
99.99%. Heat input to the column is reduced due to the heat produced
in the boiling-point reactor and reaction zone. Over time, the boiling-
reactor catalyst loses activity. As the boiling-point reactor conversion de-
creases, the CD reaction column recovers lost conversion, so that high
overall conversion is sustained. CD column overhead is washed in an
extraction column (3) with a countercurrent water stream to extract
methanol. The water extract stream is sent to a methanol recovery col-
umn (4) to recycle both methanol and water.
C
4
s ex-FCCU require a well-designed feed waterwash to remove
catalyst poisons for economic catalyst life and MTBE production.
Conversion: The information below is for 98% isobutylene conversion,
typical for renery feedstocks. Conversion is slightly less for ETBE than for
MTBE. For TAME and TAEE, isoamylene conversions of 95%+ are achiev-
able. For heavier ethers, conversion to equilibrium limits are achieved.
Economics: Based on a 1,500-bpsd MTBE unit (6,460-bpsd C
4
s ex-
FCCU, 19% vol. isobutylene, 520-bpsd MeOH feeds) located on the US
Gulf Coast, the inside battery limits investment is:
Investment, $ per bpsd of MTBE product 3,500
Typical utility requirements, per bbl of product
Continued
Installation: Over 60 units are in operation using catalytic distillation
to produce MTBE, TAME and ETBE. More than 100 ether projects have
been awarded to CDTECH since the rst unit came onstream in 1981.
Snamprogetti has over 20 operating ether units using tubular reactors.
Licensor: Snamprogetti S.p.A.
Ethers, continued
EthersETBE
Application: The Uhde (Edeleanu) ETBE process combines ethanol and
isobutene to produce the high-octane oxygenate ethyl tertiary butyl
ether (ETBE).
Feeds: C
4
cuts from steam cracker and FCC units with isobutene con-
tents ranging from 12% to 30%.
Products: ETBE and other tertiary alkyl ethers are primarily used in gas-
oline blending as an octane enhancer to improve hydrocarbon com-
bustion efciency. Moreover, blending of ETBE to the gasoline pool will
lower vapor pressure (Rvp).
Description: The Uhde (Edeleanu) technology features a two-stage re-
actor system of which the rst reactor is operated in the recycle mode.
With this method, a slight expansion of the catalyst bed is achieved that
ensures very uniform concentration proles in the reactor and, most
important, avoids hot spot formation. Undesired side reactions, such as
the formation of di-ethyl ether (DEE), are minimized.
The reactor inlet temperature ranges from 50C at start-of-run to
about 65C at end-of-run conditions. One important feature of the two-
stage system is that the catalyst can be replaced in each reactor sepa-
rately, without shutting down the ETBE unit.
The catalyst used in this process is a cation-exchange resin and is available
from several manufacturers. Isobutene conversions of 94% are typical for
FCC feedstocks. Higher conversions are attainable when processing steam-
cracker C
4
cuts that contain isobutene concentrations of about 25%.
ETBE is recovered as the bottoms product of the distillation unit. The
ethanol-rich C
4
distillate is sent to the ethanol recovery section. Water is
used to extract excess ethanol and recycle it back to process. At the top
of the ethanol / water separation column, an ethanol / water azeotrope is
recycled to the reactor section. The isobutene-depleted C
4
stream may
be sent to a rafnate stripper or to a molsieve-based unit to remove
oxygenates such as DEE, ETBE, ethanol and tert- butanol.
Utility requirements: (C
4
feed containing 21% isobutene;
per metric ton of ETBE):
Steam, LP, kg 110
Steam, MP, kg 1,000
Electricity, kWh 35
Water, cooling, m
3
24
Installations: The Uhde (Edeleanu) proprietary ETBE process has been
successfully applied in two reneries, converting existing MTBE units.
Another MTBE plant is in the conversion stage.
EthersMTBE
Application: The Uhde (Edeleanu) MTBE process combines methanol
and isobutene to produce the high-octane oxygenatemethyl tertiary
butyl ether (MTBE).
Feeds: C
4
-cuts from steam cracker and FCC units with isobutene con-
tents range from 12% to 30%.
Products: MTBE and other tertiary alkyl ethers are primarily used in gas-
oline blending as an octane enhancer to improve hydrocarbon combus-
tion efciency.
Description: The technology features a two-stage reactor system of
which the rst reactor is operated in the recycle mode. With this meth-
od, a slight expansion of the catalyst bed is achieved which ensures very
uniform concentration proles within the reactor and, most important,
avoids hot spot formation. Undesired side reactions, such as the forma-
tion of dimethyl ether (DME), are minimized.
The reactor inlet temperature ranges from 45C at start-of-run to
about 60C at end-of-run conditions. One important factor of the two-
stage system is that the catalyst may be replaced in each reactor sepa-
rately, without shutting down the MTBE unit.
The catalyst used in this process is a cation-exchange resin and is
available from several catalyst manufacturers. Isobutene conversions of
97% are typical for FCC feedstocks. Higher conversions are attainable
when processing steam-cracker C
4
cuts that contain isobutene concen-
trations of 25%.
MTBE is recovered as the bottoms product of the distillation unit.
The methanol-rich C
4
distillate is sent to the methanol-recovery section.
Water is used to extract excess methanol and recycle it back to process.
The isobutene-depleted C
4
stream may be sent to a rafnate stripper
or to a molsieve-based unit to remove other oxygenates such as DME,
MTBE, methanol and tert-butanol.
Very high isobutene conversion, in excess of 99%, can be achieved
through a debutanizer column with structured packings containing ad-
ditional catalyst. This reactive distillation technique is particularly suited
when the rafnate-stream from the MTBE unit will be used to produce
a high-purity butene-1 product.
For a C
4
cut containing 22% isobutene, the isobutene conversion
may exceed 98% at a selectivity for MTBE of 99.5%.
Utility requirements, (C
4
feed containing 21% isobutene; per metric ton
of MTBE):
Steam, MP, kg 100
Electricity, kWh 35
Water, cooling, m
3
15
Steam, LP, kg 900

Continued
Installation: The Uhde (Edeleanu) proprietary MTBE process has been
successfully applied in ve reneries. The accumulated licensed capacity
exceeds 1 MMtpy.
EthersMTBE, continued
Application: Selective conversion of a wide range of gas oils into high-
value products. Typical feedstocks are virgin or hydrotreated gas oils but
may also include lube oil extract, coker gas oil and resid.
Products: High-octane gasoline, light olens and distillate. Flexibility of
mode of operation allows for maximizing the most desirable product.
The new Selective Component Cracking (SCC) technology maximizes
propylene production.
Description: The Lummus process incorporates an advanced reaction
system, high-efciency catalyst stripper and a mechanically robust, sin-
gle-stage fast uidized bed regenerator. Oil is injected into the base of
the riser via proprietary Micro-Jet feed injection nozzles (1). Catalyst and
oil vapor ow upwards through a short-contact time, all-vertical riser (2)
where raw oil feedstock is cracked under optimum conditions.
Reaction products exiting the riser are separated from the spent cat-
alyst in a patented, direct-coupled cyclone system (3). Product vapors are
routed directly to fractionation, thereby eliminating nonselective, post-
riser cracking and maintaining the optimum product yield slate. Spent
catalyst containing only minute quantities of hydrocarbon is discharged
from the diplegs of the direct-coupled cyclones into the cyclone contain-
ment vessel (4). The catalyst ows down into the stripper (5).
Trace hydrocarbons entrained with spent catalyst are removed in the
stripper using stripping steam. The net stripper vapors are routed to the
fractionator via specially designed vents in the direct-coupled cyclones.
Catalyst from the stripper ows down the spent-catalyst standpipe and
through the slide valve (6). The spent catalyst is then transported in di-
lute phase to the center of the regenerator (8) through a unique square-
bend-spent catalyst transfer line (7). This arrangement provides the low-
est overall unit elevation. Catalyst is regenerated by efcient contacting
with air for complete combustion of coke. For resid-containing feeds, the
optional catalyst cooler is integrated with the regenerator. The resulting
ue gas exits via cyclones (9) to energy recovery/ue gas treating. The
hot regenerated catalyst is withdrawn via an external withdrawal well
(10). The well allows independent optimization of catalyst density in the
regenerated catalyst standpipe, maximizes slide valve (11) pressure drop
and ensures stable catalyst ow back to the riser feed injection zone.
Economics:
Investment (basis: 30,000 bpsd including reaction/regeneration sys-
tem and product recovery. Excluding offsites, power recovery and
ue gas scrubbing US Gulf Coast 2001.)
$/bpsd (typical) 2,2003,000
Utilities, typical per bbl fresh feed:
Electricity, kWh 0.81.0
Steam, 600 psig (produced) 50200
Maintenance, % of investment per year 23
Continued
Installation: Fourteen grassroots units in operation and one in design
stage. Fifteen units revamped and two in design stage.
Licensor: ABB Lummus Global.
Fluid catalytic cracking, continued
Application: To convert heavy distillates and residues into high-value
products, including selective propylene production when required, us-
ing the Shell FCC Process.
Description: In this process, Shells high-performance feed nozzle system
feeds hydrocarbons to a short contact-time riser; this design ensures
good mixing and rapid vaporization into the hot catalyst stream. Crack-
ing selectivity is enhanced by the feed nozzles and proprietary riser-in-
ternals, which reduce back mixing at lower pressure drop.
Riser termination design incorporates reliable close-couple cyclones
that provide rapid catalyst/hydrocarbon separation. It maximizes desired
product yields, with no slurry clean up required. Stripping begins inside
the rst cyclone, followed by a high-capacity bafe structure.
A single-stage partial or full-burn regenerator delivers excellent per-
formance at low cost. Proprietary internals are used at the catalyst inlet
to disperse catalyst, and the catalyst outlet to provide signicant catalyst
circulation enhancement. Catalyst coolers can be added for more feed-
stock exibility.
Cyclone-systems in the reactor and regenerator use a proprietary
design, thus providing reliability, efciency and robustness. Flue gas
cleanup can be incorporated with Shells third-stage separator.
Two FCC design options are available. The Shell 2 Vessel design is
recommended to handle less heavy feeds with mild coking tendencies;
the Shell External Reactor is preferred for heavy feeds with high coking
tendencies. These designs are proven reliability champions due to sim-
plicity of components and incorporation of Shells extensive operating
experience.
Installations: Over 30 grassroots units designed/licensed, including 7 to
handle residue feeds, and over 30 units revamped.
Supplier: Shell Global Solutions International B.V.

Application: Selective conversion of gas oil feedstocks.
Products: High-octane gasoline, distillate and C
3
C
4
olens.
Description: Catalytic and selective cracking in a short-contact-time riser
(1) where oil feed is effectively dispersed and vaporized through a pro-
prietary feed-injection system. Operation is carried out at a temperature
consistent with targeted yields. The riser temperature prole can be op-
timized with the proprietary mixed temperature control (MTC) system
(2). Reaction products exit the riser-reactor through a high-efciency,
close-coupled, proprietary riser termination device RS
2
(Riser Separa-
tor Stripper) (3). Spent catalyst is pre-stripped followed by an advanced
high-efciency packed stripper prior to regeneration. The reaction prod-
uct vapor may be quenched using BPs proprietary technology to give
the lowest possible dry gas and maximum gasoline yield. Final recovery
of catalyst particles occurs in cyclones before the product vapor is trans-
ferred to the fractionation section.
Catalyst regeneration is carried out in a single regenerator (4)
equipped with proprietary air and catalyst distribution systems, and may
be operated for either full or partial CO combustion. Heat removal for
heavier feedstocks may be accomplished by using reliable dense-phase
catalyst cooler, which has been commercially proven in over 24 units and
is licensed exclusively by Stone & Webster/Axens. As an alternative to
catalyst cooling, this unit can easily be retrotted to a two-regenerator
system in the event that a future resid operation is desired.
The converter vessels use a cold-wall design that results in mini-
mum capital investment and maximum mechanical reliability and safety.
Reliable operation is ensured through the use of advanced uidization
technology combined with a proprietary reaction system. Unit design is
tailored to the reners needs and can include wide turndown exibility.
Available options include power recovery, wasteheat recovery, ue gas
treatment and slurry ltration. Revamps incorporating proprietary feed
injection and riser termination devices and vapor quench result in sub-
stantial improvements in capacity, yields and feedstock exibility within
the mechanical limits of the existing unit.
Installation: Stone & Webster and Axens have licensed 27 full-technol-
ogy units and performed more than 150 revamp projects.
Reference: Letzsch, W. S., 1999 FCC Technology Advances, 1999
Stone & Webster Eleventh Annual Rening Seminar at NPRA Q&A, Dal-
las, Oct. 5, 1999.
Licensor: Stone & Webster Inc., a Shaw Group Co. /Axens, IFP Group
Technologies.

Application: Selectively convert gas oils and resid feedstocks into higher-
value products using the FCC/RFCC/PETROFCC process.
Products: Light olens (for alkylation, polymerization, etherication or
petrochemicals), LPG, high-octane gasoline, distillates and fuel oils.
Description: The combustor-style unit is used to process gas oils and
moderately contaminated resids, while the two-stage unit is used for
more contaminated resids.
In either unit style, the reactor section is similar. An acceleration me-
dia of light hydrocarbons, steam or a mixture of both contacts regener-
ated catalyst at the base of the riser (1). This patented acceleration zone
(2), with elevated Optimix feed distributors (3), enhances the yield struc-
ture by effectively contacting catalyst with nely atomized oil droplets.
The reactor zone features a short-contact-time riser and a state-of-
the-art riser termination device (4) for quick separation of catalyst and
vapor, with high hydrocarbon containment (VSS/VDS technology). This
design offers high light olen and gasoline yields and selectivity with
low dry gas yields. Steam is used in an annular stripper (5) to displace
and remove entrained hydrocarbons (AF stripper technology) from the
catalyst. Existing units can be revamped to include these features (15).
The combustor-style regenerator (6) burns coke in a fast-uidized
environment completely to CO
2
with very low levels of CO. The circula-
tion of hot catalyst (7) from the upper section to the combustor pro-
vides added control over the burn-zone temperature and kinetics and
enhances radial mixing. Catalyst coolers (8) can be added to new and
existing units to reduce catalyst temperature and increase unit exibility
for commercial operations of feeds up to 6 wt% Conradson carbon.
For heavier resid feeds, the two-stage regenerator is used. In the
rst stage, upper zone (9), the bulk of the carbon is burned from the
catalyst, forming a mixture of CO and CO
2
. Catalyst is transferred to
the second stage, lower zone (10), where the remaining coke is burned
in complete combustion, producing low levels of carbon on regener-
ated catalyst. A catalyst cooler (11) is located between the stages. This
conguration maximizes oxygen use, requires only one train of cyclones
and one ue gas stream (12), avoids costly multiple ue gas systems
and creates a hydraulically-simple and well-circulating layout. The two-
stage regenerator system has processed feeds up to 10 wt% Conradson
carbon.
PETROFCC is a customized application using mechanical features
such as RxCAT technology for recontacting carbonized catalyst, high-
severity processing conditions and selected catalyst and additives to
produce high yields of propylene, light olens and aromatics for petro-
chemical applications.
Installations: All of UOPs technology and equipment are commercially
proven for both process performance and mechanical reliability. UOP
has been an active designer and licensor of FCC technology since the
early 1940s and has licensed more than 215 FCC, Resid FCC, and MSCC
process units. Today, more than 150 of these units are operating world-
wide. In addition to applying our technology and skills to new units, UOP
is also extensively involved in the revamping of existing units. During the
past 15 years, UOPs FCC Engineering department has undertaken 40 to
60 revamp projects or studies per year.
Licensor: UOP LLC.
Application: Conversion of gas oils and residues to high-value products
using the efcient and exible Orthoow catalytic cracking process.
Products: Light olens, high-octane gasoline, and distillate.
Description: The converter is a one-piece modularized unit that ef-
ciently combines KBRs proven Orthoow features with ExxonMobils
advanced design features. Regenerated catalyst ows through a wye
(1) to the base of the external vertical riser (2). Feed enters through
the proprietary ATOMAX-2 feed injection system. Reaction vapors pass
through a patented right-angle turn (3) and are quickly separated from
the catalyst in a patented closed-cyclone system (4). Spent catalyst ows
through a two-stage stripper equipped with DynaFlux bafes (5) to the
regenerator (6) where advanced catalyst distribution and air distribution
are used. Either partial or complete CO combustion may be used in the
regenerator, depending on the coke-forming tendency of the feedstock.
The system uses a patented external ue gas plenum (7) to improve me-
chanical reliability. Catalyst ow is controlled by one slide valve (8) and
one plug valve (9). An advanced dense-phase catalyst cooler (10) is used
to optimize protability when heavier feeds are processed.
Economics:
Investment (basis: 50,000-bpsd fresh feed including converter,
fractionator, vapor recovery and amine treating, but not power
recovery; battery limit, direct material and labor, 2002 Gulf
Coast)
$ per bpsd 1,9502,150
Utilities, typical per bbl fresh feed
Steam, 600 psig (produced) lb 40200
Catalyst, makeup, lb/bbl 0.100.15
Maintenance, % of plant replacement cost/yr 3
Installation: More than 150, resulting in a total of over 4 million bpd
fresh feed, with 20 designed in the past 12 years.
References: New developments in FCC feed injection and stripping
technologies, NPRA 2000 Annual Meeting, March 2000.
RegenMax technology: staged combustion in a single regenera-
tor, NPRA 1999 Annual Meeting, March 1999.
Licensor: Kellogg Brown & Root, Inc.


Application: FLEXICRACKING IIIR converts high-boiling hydrocarbons in-
cluding residues, gas oils, lube extracts and/or deasphalted oils to higher
value products.
Products: Light olens for gasoline processes and petrochemicals, LPG,
blend stocks for high-octane gasoline, distillates and fuel oils.
Description: The FLEXICRACKING IIIR technology includes process de-
sign, hardware details, special mechanical and safety features, control
systems, ue gas processing options and a full range of technical servic-
es and support. The reactor (1) incorporates many features to enhance
performance, reliability and exibility, including a riser (2) with patented
high-efciency close-coupled riser termination (3), enhanced feed injec-
tion system (4) and efcient stripper design (5). The reactor design and
operation maximizes the selectivity of desired products, such as naphtha
and propylene.
The technology uses an improved catalyst circulation system with
advanced control features, including cold-walled slide valves (6). The
single vessel regenerator (7) has proprietary process and mechanical fea-
tures for maximum reliability and efcient air/catalyst distribution and
contacting (8). Either full or partial combustion is used. With increasing
residue processing and the need for additional heat balance control,
partial burn operation with outboard CO combustion is possible, or KBR
dense phase catalyst cooler technology may be applied. The ExxonMobil
wet gas scrubbing or the ExxonMobil-KBR Cyclones TSS technologies
can meet ue gas emission requirements.
Yields: Typical examples:
Resid feed VGO + lube extracts VGO feed
mogas distillate mogas
operation operation operation
Feed
Gravity, API 22.9 22.2 25.4
Con carbon, wt% 3.9 0.7 0.4
Quality 80% Atm. Resid 20% Lube Extracts 50% TBP 794F
(Hydrotreated)
Product yields
Naphtha, lv% ff 78.2 40.6 77.6
(C
4
/ FBP) (C
4
/ 430F) (C
4
/ 260F) (C
4
/ 430F)
Mid Dist., lv% ff 13.7 49.5 19.2
(IBP / FBP) (430 / 645F) (260 / 745F) (430 / 629F)

Continued
Installation: More than 70 units with a design capacity of over 2.5-mil-
lion bpd fresh feed.
References: Ladwig, P. K., Exxon FLEXICRACKING IIIR uid catalytic
cracking technology, Handbook of Petroleum Rening Processes, Sec-
ond Ed., R. A. Meyers, Ed., pp. 3.33.28.
Licensor: ExxonMobil Research and Engineering Co. and Kellogg Brown
& Root, Inc. (KBR).
Fluid catalytic crackingpretreatment
Application: Topses FCC pretreatment technology is designed to treat
a wide variety of feedstocks ranging from gas oils through heavy-vacu-
um gas oils and coker streams to resids. This pretreatment process can
maximize FCC unit performance.
Objectives: The processing objectives range from deep desulfurization
for meeting gasoline-sulfur specications from the FCC products, to de-
nitrogenation and metals removal, thus maximizing FCC catalyst activ-
ity. Additional objectives can include Conradson carbon reduction and
saturation of polyaromatics to maximize gasoline yields.
Description: The Topse FCC Pretreatment technology combines under-
standing of kinetics, high-activity catalysts, state-of-the-art internals and
engineering skills. The unit can be designed to meet specic process-
ing objectives in a cost-effective manner by utilizing the combination of
processing severity and catalyst activity.
Topse has experience in revamping moderate- to low-pressure units
for deep desulfurization. Such efforts enabled reners to directly blend
gasoline produced from the FCC and meet future low-sulfur (less than
30 ppm) gasoline specications.
An additional option is Topses Aroshift process that maximizes the
conversion of polyaromatics which can be equilibrium limited at high
operating temperatures. The Aroshift process increases the FCC conver-
sion, and the yield of gasoline and C
3
/C
4
olens, while reducing the
amount of light- and heavy-cycle oil. Furthermore, the quality of the
FCC gasoline is improved.
Topse has a wide variety of catalysts for FCC pretreatment service.
The catalyst types cover TK-558, a CoMo catalyst with high desulfurization
activity, and TK-559, a NiMo catalyst with hydrodesulfurization and hy-
drodenitrogenation activity. Topse offers a wide range of engineering
scopes from scoping studies, reactor design packages and process de-
sign packages to engineering design packages.
Operating conditions: Typical operating pressures range from 60 bar
(900 psi) to 125 bar (1,800 psi), and temperatures from 300C (575F)
to 430C (800F).
References: Patel R., H. Moore and B. Hamari, FCC hydrotreater re-
vamp for low-sulfur gasoline, NPRA Annual Meeting, San Antonio,
March 2123, 2004.
Patel, R., P. Zeuthen and M. Schaldemose, Advanced FCC feed pre-
treatment technology and catalysts improves FCC protability, NPRA
2002 Annual Meeting.
Installations: Four units are operating in the US.
Gas treatingH
2
S removal
Application: Remove H
2
S selectively, or remove a group of acidic impuri-
ties (H
2
S, CO
2
, COS, CS
2
and mercaptans) from a variety of streams, de-
pending on the solvent used. FLEXSORB SE technology has been used in
reneries, natural gas production facilities and petrochemical operations.
FLEXSORB SE or SE Plus solvent is used on: hydrogenated Claus plant
tail gas to give H
2
S, ranging down to H
2
S <10 ppmv; pipeline natural
gas to give H
2
S <0.25 gr/100 scf; or Flexicoking low-Btu fuel gas. The
resulting acid gas byproduct stream is rich in H
2
S.
Hybrid FLEXSORB SE solvent is used to selectively remove H
2
S, as
well as organic sulfur impurities commonly found in natural gas.
FLEXSORB PS solvent yields a treated gas with: H
2
S <0.25 gr/100
scf, CO
2
<50 ppmv, COS and CS
2
<1 ppmv, mercaptans removal >95%.
This solvent is primarily aimed at natural gas or syngas cleanup. The
byproduct stream is concentrated acid gases.
Description: A typical amine system ow scheme is used. The feed gas
contacts the treating solvent in the absorber (1). The resulting rich sol-
vent bottom stream is heated and sent to the regenerator (2). Regen-
erator heat is supplied by any suitable heat source. Lean solvent from
the regenerator is sent through rich/lean solvent exchangers and coolers
before returning to the absorber.
FLEXSORB SE solvent is an aqueous solution of a hindered amine.
FLEXSORB SE Plus solvent is an enhanced aqueous solution, which has
improved H
2
S regenerability yielding <10 vppm H
2
S in the treated gas.
Hybrid FLEXSORB SE solvent is a hybrid solution containing FLEXSORB
SE amine, a physical solvent and water. FLEXSORB PS solvent is a hybrid
consisting of a different hindered amine, a physical solvent and water.
Economics: Lower investment and energy requirements based primarily
on requiring 30% to 50% lower solution circulation rates.
Installations: Total gases treated by FLEXSORB solvents are about 2 bil-
lion scfd and the total sulfur recovery is about 900 long tpd.
FLEXSORB SE31 plants operating, two in design
FLEXSORB SE Plus16 plants operating, two startups in 2004, six
in design
Hybrid FLEXSORB SEtwo plants operating, two in design
FLEXSORB PSfour plants operating.
Reference: Garrison, J., et al., Keyspan Energy Canada Rimbey acid gas
enrichment with FLEXSORB SE Plus technology, 2002 Laurance Reid
Gas Conditioning Conference, Norman, Oklahoma.
Adams-Smith, J., et al., Chevron USA Production Company, Carter
Creek Gas Plant FLEXSORB tail gas treating unit, 2002 GPA Annual
Meeting, Dallas.
Fedich, R., et al., Selective H
2
S Removal, Hydrocarbon Engineer-
ing, May 2004.

Gasification
Application: The FUTURE ENERGY (FE) Gasication process (formerly
known as the GSP process or NOELL process and now owned by
FE) processes liquid, solid or gaseous waste materials from the renery
(petcoke, heavy residues), chemical industry and coals (hard coal, lig-
nite) into a clean, tar-free synthesis gas, which can be further converted
into value materials such as methanol, hydrogen, fertilizers or energy.
Byproducts are a vitried granulated slag, elemental sulfur and soluble
heavy metal suldes recovered in the wastewater treatment.
Due to the reducing atmosphere prevailing in all process stages, gas-
ication, in contrast to incineration, allows treatment of waste materi-
als and residues meeting high environmental standards and to utilize the
product syngas for chemical production or power generation. Toxic com-
ponents are decomposed, and there will not be a de-novo synthesis.
Description: The basic version of FEs entrained-ow gasier was devel-
oped for the gasication of pulverized brown coal. Later, this gasier
technology was shaped up for the universal use of ash-containing fuels.
The reactants are fed to the gasier via special-design burners on top of
the reaction chamber and are converted in a ame reaction.
The oxygen-to-fuel ratio is trimmed to keep the gasication temperature
at a level at which the inorganic matter melts and ows vertically downward
in parallel with the gasication gas and leaves the gasier through a special
discharge unit. Carbon conversion rates of more than 99% are achieved.
Dependent on the further use of the gas produced, a direct-contact water-
spray-quench system or an indirect-cooling heat recovery steam generator
system can be installed downstream of the gasier.
The gasication chamber is enclosed by a cooling screen which con-
sists of gas-tight welded cooling tubes. These are studded and refrac-
tory-lined with a thin layer of a special SiC ramming mass. Liquid slag
on this cooling screen cools down and solidies and forms a compact
slag layer that performs similar to a refractory lining. The solidied slag
layer grows in thickness until the ash-fusion temperatures are exceeded.
Slag then hitting the wall remains in liquid condition, ows downward
the wall and discharges at the bottom together with the gasication
gas. The reactor design with cooling screen described requires gasica-
tion feeds with ash contents of more than 1 wt% allowing the solidied
slag layer to constantly regenerate. This is not given if the ash content is
lower. In this case, a cooling wall reactor design is used, where a refrac-
tory lining replaces the missing slag layer. A water jacket is substituted
for the tube screen.
Economics: Unit costs are very much dependent on the value/tipping
fee of the feed material and the total plant design, as well as the nal
product/single processing steps desired.

Continued
Installations: The FE gasier has been operating successfully at SVZ
Schwarze Pumpe, Spreeetal/Spreewitz, Germany, since 1984, rst on
brown coal and then on sludges, ash-containing oils and slurries. The
cooling screen design ensures long gasier availability periods before
requiring repair or relining. Over eight years, it has been proven on
an industrial scale. Compared with a conventional refractory lining,
the cooling screen is insensitive to high ash content or uctuating ash
composition. The gasier can be started up or shut down within a few
minutes.
A further example is the Seal Sands gasication facility, Middles-
brough, UK, of BASF plc., which was constructed to process 110,000
tpy of liquid waste (mixtures of nitriles and amines, as well as cyanide
and ammonia compounds). A 140 MWth Autothermal Oil Conversion
Plant for Sokolovsk uheln, a.s., Vresov, Czech Republic, is under con-
struction.
References: GasicationAn opportunity to design environmentally
compatible processes in the chemical and pulp & paper industry, Chem.
Eng.Technology, Vol. 26 (2003), Wiley-VCH, Verlag, Weinheim.
Experience during erection and commissioning of the gasication
plant Seal Sands, UK, 2001 Gasication Technologies Conference, San
Francisco, Oct. 710, 2001.
Gasication of solids bearing tars in the entrained ow gasiers
of FUTURE ENERGY, 6th European Gasication Conference, Brighton,
May 1012, 2004.
Licensor: FUTURE ENERGY GmbH.
Gasification, continued
Gasification
Application: The GE Gasication Process (formerly known as the Texaco
Gasication Process) converts residual liquid renery bottoms streams
containing high sulfur and metals to hydrogen, fuel gas, chemical syn-
thesis gas ( CO + H
2
) and high-pressure steam. Renery liquid-waste
streams may be used as supplemental feed. A coke water slurry may also
be used as an alternate feed.
The sulfur is removed as H
2
S compatible with standard renery sul-
fur recovery units (SRUs) or acid-gas reinjection. Metals are removed in
a lter cake, which may be optionally processed (offsite or onsite) for
nickle (Ni) and vanadium (V) recovery. If desired up to 95% of the car-
bon in the feed can be recovered as a byproduct puried-CO
2
stream
compatible with enhanced oil or gas recovery.
The process converts the lowest value residual streamsvisbreaker
tar, deasphalter tar or cokeinto high-value products. Typically 8090%
of the energy in the tar is recovered in product and HP-export steam
streams. Fuel gas produced in gasication is well suited for combustion
turbines. It has a higher mass ow than natural gas and typically gener-
ates 10 20% more power than natural gas in a combustion turbine.
The gasication process is an environmentally acceptable and energy
efcient solution for residual renery bottoms streams.
Products: Hydrogen, synthesis gas (CO + H
2
), fuel gas, sulfur (as acid
gas) and lter cake (for metals recovery).
Process: Liquid-bottoms tar stream is mixed with hot soot water and
fed with oxygen to the pressurized refractory-lined gasier. The gas-
ier operates at high pressure (400 800 psig) and temperatures
(2,300 2,700F), which breaks down all hydrocarbons into CO and H
2
with a small amount of soot (unconverted carbon) and ash. Gasier
pressures up to 1,250 psig are possible in an alternate water-quench
design.
A syngas cooler chills the gasier outlet gas and produces high-pres-
sure steam (up to 2,000 psig). The cooled gas is scrubbed with water
to remove the soot and ash. All or a portion of the moisturized gas is
reacted in a xed-bed catalytic shift reactor; CO reacts with steam to
produce additional hydrogen and CO
2
. This allows the adjustment of
the H
2
/ CO ratio in the syngas to any value greater than 1. More heat
is recovered from the exothermic - shift reaction by superheating steam
and economizing boiler feedwater. Excess condensate is blown down to
an offsite sour-water stripper (SWS).
The dry gas is then separated into its various components using
conventional amine, physical solvent or cryogenic gas separations. A
conventional PSA unit is used for nal hydrogen purication.
A portion of the byproduct soot water is recycled to the gasier; the
remainder is ltered to remove the soot and ash. The lter cake can be
Continued
optionally processed using commercial metals reclaiming processes to
recover the Ni and V.
Yields:
Feed, source Maya Crude Oil Sands
Type SDA Tar Visbr Tar
API 4.4 0
Sulfur, wt% 7 7
Ni + V, ppm 1,200 600
Products
Hydrogen, Mscf / bbl 14 14
CO
2
, tons / bbl 0.5 0.5
Fuel gas, 10
6
Btu / bbl 0.8 0.8
Economics:
Investment, $ per bpsd 16,000 14,000
(basis 10,000 bpsd, on plot facilities only, exclude contingency,
owners cost, sales tax 1st Q, 2004, US Gulf)
Utilities, typical per bbl feed
Steam SH HP, export, lb 500 600
Steam Satd LP, cons, lb 0 100
Power (exc l CO
2
compression), kWh 12 12
Oxygen, tons 0.2 0.2
Water, cooling, gal 1,800 1,400
Installation: More than 50 resid-bottoms units utilizing the GE Gasi-
cation Process are in commercial operation worldwide in various ap-
plications including hydrogen production, combustion turbine fuel gas
production and syngas for chemical synthesis.
Licensor: GE Energy.
Gasification
Application: The Shell Gasication Process (SGP) converts the heaviest
residual liquid hydrocarbon streams with high-sulfur and metals content
into a clean synthesis gas and valuable metal oxides. Sulfur (S) is re-
moved by normal gas treating processes and sold as elemental S.
The process converts residual streams with virtually zero value as
fuel-blending components into valuable, clean gas and byproducts.
This gas can be used to generate power in gas turbines and for making
H
2
by the well-known shift and PSA technology. It is one of the few ul-
timate, environmentally acceptable solutions for residual hydrocarbon
streams.
Products: Synthesis gas (CO+H
2
), sulfur and metal oxides.
Process description: Liquid hydrocarbon feedstock (from very light
such as natural gas to very heavy such as vacuum ashed cracked
residue, VFCR and ashphalt) is fed into a reactor, and gasied with
pure O
2
and steam. The net reaction is exothermic and produces a
gas primarily containing CO and H
2
. Depending on the nal syngas
application, operating pressures, ranging from atmospheric up to 65
bar, can easily be accommodated. SGP uses refractory-lined reactors
that are tted with both burners and a heat-recovery-steam generator,
designed to produce high-pressure steamover 100 bar (about 2.5
tons per ton feedstock). Gases leaving the steam generator are at a
temperature approaching the steam temperature; thus, further heat
recovery occurs in an economizer.
Soot (unconverted carbon) and ash are removed from the raw gas
by a two-stage waterwash. After the nal scrubbing, the gas is virtually
particulate-free; it is then routed to a selective-acid-gas-removal system.
Net water from the scrubber section is routed to the soot ash removal
unit (SARU) to lter out soot and ash from the slurry. By controlled oxi-
dation of the ltercake, the ash components are recovered as valuable
oxidesprincipally vanadium pentoxide. The (clean) ltrate is returned
to the scrubber.
A related processthe Shell Coal Gasication Process (SCGP)gas-
ies solids such as coal or petroleum coke. The reactor is different, but
main process layout and work-up are similar.
Installation: Over the past 40 years, more than 150 SGP units have been
installed that convert residue feedstock into synthesis gas for chemical
applications. The latest, agship installation is in the Shell Pernis renery
near Rotterdam, The Netherlands. This highly complex renery depends
on the SGP process for its H
2
supply. Similar projects are underway in
Canada and Italy.
The Demkolec Power plant at Buggenum, The Netherlands pro-
duces 250 Mwe based on the SCGP process. The Shell middle distillate

Continued
synthesis plant in Bintulu, Malaysia, uses SGP to convert 100 million scfd
of natural gas into synthesis gas that is used for petrochemical applica-
tions.
Reference: Shell Gasication Process, Conference Dening the Fu-
ture, Bahrain, June 12, 2004.
Shell Gasication Process for Upgrading Gdansk Renery, The
6th European Gasication Conference IChemE, Brighton, May 1012,
2004.
Overview of Shell Global Solutions Worldwide Gasication Devel-
opments, 2003 Gasication Technologies Conference, San Francisco,
Oct. 1215, 2003.
Application: Convert high-sulfur gasoline streams into a low-sulfur gas-
oline blendstock while minimizing octane loss, yield loss and operating
cost using S Zorb sulfur removal technology.
Products: A zero sulfur blending stock for gasoline motor fuels.
Description: Gasoline from the uid catalytic cracker unit is combined
with a small hydrogen stream and heated. Vaporized gasoline is injected
into the uid-bed reactor (1), where the proprietary sorbent removes
sulfur from the feed. A disengaging zone in the reactor removes sus-
pended sorbent from the vapor, which exits the reactor to be cooled.
Regeneration: The sorbent (catalyst) is continuously withdrawn from the
reactor and transferred to the regenerator section (2), where the sulfur
is removed as SO
2
and sent to a sulfur-recovery unit. The cleansed sor-
bent is reconditioned and returned to the reactor. The rate of sorbent
circulation is controlled to help maintain the desired sulfur concentra-
tion in the product.
Economics:
Typical operating conditions:
Pressure, psig 100 500
Space velocity, whsv 4 8
Hydrogen purity, % 70 99
Total H
2
usage, scf / bbl 40 60
Case study premises:
25,000 - bpd feed
775 - ppm feed sulfur
25 - ppm product sulfur ( 97% removal )
No cat gasoline splitter
Results:
C
5
+ yield, vol% of feed >100%
Lights yield, wt% of feed < 0.1
(R+M) loss
2 <0.3
Operating cost, /gal* 0.9
* Includes utilities, 4% per year maintenance and sorbent costs.
Installation: Forty-three sites licensed as of 1Q 2004.

Application: Ultra-deep desulfurization of FCC gasoline with minimal
octane penalty using Prime-G+ process.
Description: FCC debutanizer bottoms are fed directly to a rst reactor
wherein, under mild conditions, diolens are selectively hydrogenated
and mercaptans are converted to heavier sulfur species. The selective
hydrogenation reactor efuent is then usually split to produce an LCN
(light cat naphtha) cut and an HCN (heavy cat naphtha).
The LCN stream is mercaptans-free with a low-sulfur and diolen
concentration, enabling further processing in an etherication or alkyla-
tion unit. The HCN then enters the main Prime-G+ section where it under-
goes in a dual catalyst reactor system; a deep HDS with very limited olens
saturation and no aromatics losses produces an ultra-low-sulfur gasoline.
The process provides exibility to advantageously co-process other
sulfur-containing naphthas such as light coker naphtha, steam cracker
naphtha or light straight-run naphtha.
Industrial results:
Full-range FCC Gasoline, Prime-G+
40C220C Feed Product
Sulfur, ppm 2,100 50*
(RON + MON) / 2 87.5 86.5
(RON + MON) / 2 1.0
% HDS 97.6
30 ppm pool sulfur after blending
Pool sulfur specications as low as less than 10 ppm are attained
with the Prime-G+ process in two units in Germany.
Economics:
Investment: Grassroots ISBL cost, $/bpsd 600800
Installation: Ninety-two units have been licensed for a total capacity of
2.4 million bpsd. Thirty-two Prime-G+ units are already in operation, pro-
ducing ultra-low-sulfur gasoline. Twenty other units will come onstream
at the end of 2004.
OATS process: In addition to the Prime-G+ technology, the OATS
(olens alkylation of thiophenic sulfur), initially developed by BP, is also
exclusively offered for license by Axens for ultra-low-sulfur gasoline
production.
Reference: Prime-G+: From pilot to start-up of worlds rst commercial
10 ppm FCC gasoline desulfurization process, NPRA Annual Meeting,
March 1719, 2002, San Antonio.
Licensor: Axens.

Application: Reduce sulfur in gasoline to less than 10 ppm by
hydrodesulfurization followed by cracking and isomerization to recover
octane with the OCTGAIN process.
Description: The basic ow scheme of the OCTGAIN process is similar to
that of a conventional naphtha hydrotreater. Feed and recycle hydrogen
mix is preheated in feed/efuent exchangers and a red heater then in-
troduced into a xed-bed reactor. Over the rst catalyst bed, the sulfur
in the feed is converted to hydrogen sulde (H
2
S) with near complete
olen saturation. In the second bed, over a different catalyst, octane is
recovered by cracking and isomerization reactions. The reactor efuent
is cooled and the liquid product separated from the recycle gas using
high- and low-temperature separators.
The vapor from the separators is combined with makeup gas, com-
pressed and recycled. The liquid from the separators is sent to the prod-
uct stripper where the light ends are recovered overhead and desulfur-
ized naphtha from the bottoms. The product sulfur level can be as low
as 5 ppm. The OCTGAIN process can be retrotted into existing renery
hydrotreating units. The design and operation permit the desired level
of octane recovery and yields.
EMRE has an alliance with Kellogg Brown & Root (KBR) to provide
this technology to reners.
Yields: Yield depends on feed olens and desired product octane.
Installations: Commercial experience with two operating units.
Reference: Halbert, T., et al., Technology Options For Meeting Low-Sul-
fur Mogas Targets, NPRA Annual Meeting, March 2000.
Licensor: ExxonMobil Research and Engineering (EMRE) Co.

Application: Reduce sulfur in FCC gasoline to levels as low as <10 wppm
by selective hydrotreating to maximize octane retention with the SCAN-
ning technology.
Description: The feed is mixed with hydrogen, heated with reactor efu-
ent exchange and passed through a pretreat reactor for diolen satura-
tion. After further heat exchange with reactor efuent and preheat using
a utility, the hydrocarbon/hydrogen mixture enters the main reaction sec-
tion which features ExxonMobil Research and Engineering Co. (EMRE)
proprietary selective catalyst systems. In this section of the plant, sulfur
is removed in the form of H
2
S under tailored process conditions, which
strongly favor hydrodesulfurization while minimizing olen saturation.
The feed may be full-range, intermediate or heavy FCC-naphtha
fraction. Other sulfur-containing streams such as light-coker naphtha,
steam cracker or light straight-run naphthas can also be processed with
FCC naphthas. SCANning technology can be retrotted to existing
units such as naphtha or diesel hydrotreaters and reformers. SCANning
technology also features ExxonMobils proprietary reactor internals such
as Automatic Bed Bypass Technology for onstream mitigation of reactor
plugging/pressure drop buildup.
For high-sulfur feeds and/or very low-sulfur product, with low levels
of product mercaptans variations in the plant design from SCANning I
Process to the SCANning II Process for greater HDS selectivity, or addi-
tion of a ZEROMER process step for mercaptan conversion, or addition
of an EXOMER process unit for mercaptan extraction.
EMRE has an alliance with Kellogg Brown & Root (KBR) to pro-
vide SCANning technology to reners and an alliance with Merichem
Chemicals & Renery Services LLC to provide EXOMER technology to
reners.
Yields: Yield of C
5
+ liquid product is typically over 100 LV%.
Installation: Thirty-one units under design, construction or operation
having combined capacity of over 900,000 bpsd.
References: Sapre, A.V., et al., Case History: Desulfurization of FCC
naphtha, Hydrocarbon Processing, February 2004.
Ellis, E. S., et al., Meeting the Low Sulfur Mogas Challenge, World
Rening Association Third European Fuels Conference, March 2002.
H
2
S and SWS gas conversion
Application: The ATS process recovers H
2
S and NH
3
in amine regenera-
tor offgas and sour water stripper gas (SWS gas) as a 60% aqueous
solution of ATS ammonium thiosulfate (NH
4
)
2
S
2
O
3
, which is the stan-
dard commercial specication. The ATS process can be combined with
a Claus unit; thus increasing processing capacity while obtaining a total
sulfur recovery of > 99.95%. The ATS process can also handle SWS gas
alone without ammonia import while the S / N balance is adjusted by
exchanging H
2
S surplus and decit with a Claus unit.
ATS is increasingly used as a fertilizer (12- 0 - 0 -26S) for direct appli-
cation and as a component in liquid fertilizer formulations.
Description: Amine regenerator off gas is combusted in a burner / waste
heat boiler. The resulting SO
2
is absorbed with ammonia in a two-stage
absorber to form ammonium hydrogen sulte (AHS). NH
3
and H
2
S con-
tained in the SWS gas plus imported ammonia (if required) is reacted
with the AHS solution in the ATS reactor. The ATS product is withdrawn
as a 60% aqueous solution that meets all commercial specications for
usage as a fertilizer. Unreacted H
2
S is returned to the H
2
S burner.
Except for the H
2
S burner / waste heat boiler, all process steps occur
in the liquid phase at moderate temperatures and neutral pressure. The
AHS absorber and ATS reactor systems are chilled with cooling water.
More than 99.95% of the sulfur and practically 100% of the am-
monia contained in the feed gas streams are recovered. Typical emission
values are:
SO
x
<100 ppmv
NO
x
<50 ppmv
H
2
S <1 ppmv
NH
3
<20 ppmv
Installation: One Topse 30,000 mtpy ATS plant is operating in Northern
Europe.

H
2
S removal
Application: LO-CAT removes H
2
S from gas streams and produces el-
emental sulfur. LO-CAT units are in service treating renery fuel gas,
hydrodesulfurization offgas, sour-water-stripper gas, amine acid gas,
claus tail gas and sulfur tank vent gas. Sulfur capacities are typically less
than 25 ltpd down to several pounds per day. Key benets of operation
are high (99.9%) H
2
S removal efciency, and exible operation, with vir-
tually 100% turndown capability of H
2
S composition and total gas ow.
Sulfur is recovered as a slurry, lter cake or high-purity molten sulfur.
The sulfur cake is increasingly being used in agriculture, but can also be
deposited in a nonhazardous landll.
Description: The conventional conguration is used to process combus-
tible gas and product gas streams. Sour gas contacts the dilute, propri-
etary, iron chelate catalyst solution in an absorber (1), where the H
2
S is
absorbed and oxidized to solid sulfur. Sweet gas leaves the absorber for
use by the renery. The reduced catalyst solution returns to the oxidizer
(2), where sparged air reoxidizes the catalyst solution. The catalyst solu-
tion is returned to the absorber. Continuous regeneration of the catalyst
solution allows for very low chemical operating costs.
In the patented autocirculation conguration, the absorber (1) and
oxidizer (2) are combined in one vessel, but separated internally by baf-
es. Sparging of the sour gas and regeneration air into the specially
designed bafe system creates a series of gas lift pumps, eliminating
the external circulation pumps. This conguration is ideally suited for
treating amine acid gas and sour-water-stripper gas streams.
In both congurations, sulfur is concentrated in the oxidizer cone
and sent to a sulfur lter, which can produce lter cake as high as 85%
sulfur. If desired, the lter cake can be further washed and melted to
produce pure molten sulfur.
Operating conditions: Operating pressures range from vacuum condi-
tions to 1,000 psi. Operating temperatures range from 40F to 140F.
Hydrogen sulde concentrations range from a few ppm to 100%. Sul-
fur loadings range from a few pounds per day to 25+ tons per day. No
restrictions on type of gas to be treated; however, some contaminants,
such as SO
2
, may increase operating costs.
Installations: Presently, 160 licensed units are in operation with four
units under construction.
Reference: Heguy, D. L. and G. L. Nagl, Consider optimized Iron-Redox
processes to remove sulfur, Hydrocarbon Processing, January 2003, pp.
5357.
Licensor: Gas Technology Products LLC, a Merichem Co.
H
2
S removal
Applications: Sulfur-Rite is a solid-bed scavenger for removal of H
2
S from
aerobic and anaerobic gas streams. Suitable applications are generally
sulfur loads below 200 lb/d sulfur, and/or remote renery locations. Sul-
fur vents, loading and unloading facilities, or backup insurance for other
renery sulfur-removal systems are examples.
The spent media is nonpyrophoric, and is suitable for disposition in
nonhazardous landlls.
Description: Single-bed (shown) or dual lead-lag congurations are
possible. Sour gas is saturated prior to entering media bed. Gas enters
vessel top, ows over media where H
2
S is removed and reacted. Sweet
gas exits the bottom of vessel. In the single-vessel conguration, when
the H
2
S level exceeds the level allowed, the vessel must be bypassed,
media removed through the lower manway, fresh media installed and
vessel returned to service.
For continuous operation, a dual lead-lag conguration is desir-
able. The two vessels operate in series, with one vessel in the lead posi-
tion, the other in the lag position. When the H
2
S level at the outlet of
the lead vessel equals the inlet H
2
S level (the media is completely spent),
the gas ow is changed and the vessels reverse rolls, so that the lag
vessel becomes the lead vessel. The vessel with the spent media is
bypassed. The media is replaced, and the vessel with fresh media is re-
turned to service in the lag position.
Operating conditions: Gas streams up to 400F can be treated. Gas
streams should be at least 50% water saturated.
Installations: Five units installed.
Licensor: Gas Technology Products LLC, a Merichem Co.

H
2
S removal, Thiopaq
Application: The biological Thiopaq process selectively removes and con-
verts H
2
S and light mercaptans from gas streams, aqueous streams and/
or light hydrocarbons to elemental sulfur or sulfate.
Product: The sulfur produced is hydrophilic; thus, it prevents equipment
from fouling and blocking. Moreover, this characteristic makes the prod-
uct suitable for agricultural use as fertilizer or as an insecticide. Alterna-
tively, the sulfur can be molten to a high-purity product meeting inter-
national Claus sulfur specications.
Description: The Thiopaq process consists of three integrated process
sections: an absorption section to remove the H
2
S from the gas stream,
bioreactor(s) and a sulfur-separation section.
The heart of this process is the proprietary bioreactor. In this air-lift-loop
reactor, sulde (HS
) is oxidized under controlled conditions to elemental sul-

fur in the presence of microorganisms. These aerobic (oxygen consuming)
organisms use the released energy from the sulde oxidation for metabolic
processes. The elemental sulfur produced has a hydrophilic nature and is sep-
arated from the aqueous efuent in a proprietary three-phase separator.
The scrubbing step to remove H
2
S from the gas streams is inte-
grated into the Thiopaq process and regenerates the scrubbing solution,
rather than its disposal. Regeneration is possible because the alkalinity
consumption due to the absorption of H
2
S is compensated by the oxida-
tion of H
2
S to elemental sulfur.
Operating conditions: The absorber operates at the pressure of feed and
at bio reactor temperature. The bioreactor operates at atmospheric pres-
sure and 3035C. If the feed is available at a higher temperature, then
it requires cooling before entering the absorber.
Economics: The costs associated with using Thiopaq to treat typical re-
nery spent caustic of a owrate of 9,510 gpd containing 2,970 lbs/day
of sulde:
Capital cost, budget $1,500,000
Annual operating cost $158,000
The cost of an LPG ow of 1,500 BSD and recovery of 1,500 lbs/d of
sulfur and achieving < 5ppm H
2
S in the treated LPG:
The costs for an offgas owrate of 24,200 lbs/hr and recovery of 7.8
tpd of sulfur:

Continued
Installations: Thirty-two units are operating worldwide to remove sulfur
from gas and liquid streams in a variety of industries. This includes a 13-
mtpd unit in a renery service in Egypt.
Licensors: UOP LLC, Shell International Oil Products B.V., and Paques
Bio System B.V.
H
2
S removal, Thiopaq, continued
Hydrocracking
Application: Upgrade vacuum gas oil alone or blended with various
feedstocks (light-cycle oil, deasphalted oil, visbreaker or coker-gas oil).
Products: Middle distillates, very-low-sulfur fuel oil, extra-quality FCC
feed with limited or no FCC gasoline post-treatment or high VI lube
base stocks.
Description: This process uses a rening catalyst usually followed by a
zeolite-type hydrocracking catalyst. Main features of this process are:
High tolerance toward feedstock nitrogen
High selectivity toward middle distillates
High activity of the zeolite, allowing for 34 year cycle lengths and
products with low aromatics content until end of cycle.
Three different process arrangements are available: single-step/
once-through; single-step/total conversion with liquid recycle; and two-
step hydrocracking. The process consists of: reaction section (1, 2), gas
separator (3), stripper (4) and product fractionator (5).
Product quality: Typical for HVGO (50/50 Arabian light/heavy):
Feed, Jet
HVGO fuel Diesel
Sp. gr. 0.932 0.800 0.826
TBP cut point, C 405565 140225 225360
Sulfur, ppm 31,700 <10 <10
Nitrogen, ppm 853 <5 <5
Metals, ppm <2
Cetane index 62
Flash pt., C 6 40 125
Smoke pt., mm, EOR 2628
Aromatics, vol%, EOR < 12 < 8
Viscosity @ 38C, cSt 110 5.3
PAH, wt%, EOR <2
Economics:
Investment: (Basis: 40,000-bpsd unit, once-through, 90% conver-
sion, battery limits, erected, engineering fees included, 2000 Gulf
Coast), $ per bpsd 2,0002,500
Fuel oil, kg 5.3
Water, cooling, m
3
0.64
Steam, MP balance
Installation: More than 50 references, cumulative capacity exceeding 1
million bpsd, conversion ranging from 50% to 99%.
Licensor: Axens.

Hydrocracking
Application: Convert naphthas, AGO, VGO, DAO, cracked oils from FCC
units, delayed cokers and visbreakers, and intermediate products from
residue hydroprocessing units using the Chevron Lummus Global ISO-
CRACKING Process.
Products: Lighter, high-quality, more valuable products: LPG, gasoline,
catalytic reformer feed, jet fuel, kerosene, diesel and feeds for FCC, eth-
ylene cracker or lube oil units.
Description: A broad range of both amorphous/zeolite and zeolitic
catalysts, including noble-metal zeolitic catalysts, are used to tailor the
ISOCRACKING Process exactly to the reners objectives. In general,
the process involves a staged reactor system with an initial stage of
hydrotreating and partially hydrocracking the feed, and a subsequent
stage continuing the conversion or product upgrade process in a more
favorable environment.
Feeds can be introduced in between stages using Chevron Lummus
Global patented split-feed injection technology, or efuent ow paths can
be arranged to best utilize hydrogen and minimize quench-gas requirements
using proprietary SSRS (single-stage reaction sequenced) technology.
Most modern large-capacity ow schemes involving heavy sour gas
oils require two reactors (1, 4) and one high-pressure separation system
(2) with an optional recycle gas scrubber (5) and one recycle-gas com-
pressor (8). The low-pressure separators (3), product stripper (6) and
fractionator (7) provide the exibility to fractionate products either in
between reaction stages or at the tail-end, depending on desired prod-
uct slate and selectivity requirements.
Single-stage options are used in once-through mode typically for
mild hydrocracking or when a signicant quantity of unconverted oil is
required for FCC, lubes, or ethylene units. The single-stage recycle op-
tion is used for lower capacity units when economical. The reactors use
patented internals technology called ISOMIX for near-awless mixing
and redistribution.
Yields: Typical from various feeds:
Feed VGO VGO VGO VGO
Gravity, API 24.1 24.1 24.1 21.3
TBP range, F 7001,100 7001,100 7001,100 7001,100
Nitrogen, wppm 2,500 2,500 2,500 900
Sulfur, wt % 1.9 1.9 1.9 2.5
Mode Max. Diesel Max. Jet Max. Mid- Max. Mid-
Distillate Distillate
+ Lubes
Yields, vol %
Naphtha 22.8 30.8 14.0 18
Jet/kerosine 79.7 22.0 50
Diesel 85.5 73.0 35
UCO 10
Continued
Feed VGO VGO VGO VGO
Product quality
Kerosine smoke, mm 2932 2932 2932
Diesel cetane number 5864 5864 5864
UCO BMCI 68
UCO Waxy V.I. 143145
UCO Dewaxed V.I. 131133
Economics: ISBL total installed cost of 35,000-BPSD unit at 100% con-
version to middle distillates using Middle Eastern VGO feed (USGC, mid-
2004 basis): $110 million.
Process fuel (absorbed), MMBtu/hr 180
Electricity, MW 10
CW, gpm 2,500
Steam (export at 150 psig), M lb/hr 22
Installation: More than 50 units worldwide with over 800,000-bpsd to-
tal capacity.
Hydrocracking, continued
Hydrocracking
Application: Desulfurization, demetalization, CCR reduction and hydro-
cracking of atmospheric and vacuum resids using the LC-FINING Pro-
cess.
Products: Full range of high-quality distillates. Residual products can
be used as fuel oil, synthetic crude or feedstock for a resid FCC, coker,
visbreaker or solvent deasphalter.
Description: Fresh hydrocarbon liquid feed is mixed with hydrogen and
reacted within an expanded catalyst bed (1) maintained in turbulence by
liquid upow to achieve efcient isothermal operation. Product quality is
maintained constant and at a high level by intermittent catalyst addition
and withdrawal. Reactor products ow to a high-pressure separator (2),
low-pressure separator (3) and product fractionator (4). Recycle hydro-
gen is separated (5) and puried (6).
Process features include onstream catalyst addition and withdrawal.
Recovering and purifying the recycled H
2
at low pressure rather than at high
pressure can reduce capital cost and allows design at lower gas rates.
Reactor temperature, F 725 840
Reactor pressure, psig 1,400 3,500
H
2
partial pressure, psig 1,000 2,700
LSHV 0.1 to 0.6
Conversion, % 40 97+
Desulfurization, % 60 90
Demetalization, % 50 98
CCR reduction, % 35 80
Yields: For Arabian heavy/Arabian light blends:

Atm. resid Vac. resid
Feed
Gravity, API 12.40 4.73 4.73 4.73
Sulfur, wt % 3.90 4.97 4.97 4.97
Ni/V, ppmw 18 /65 39 /142 39 /142 39 /142
Conversion, vol% (1,022F+) 45 60 75 95
Products, vol%
C
4
1.11 2.35 3.57 5.53
C
5
350F 6.89 12.60 18.25 23.86
350 700F (650F) (15.24) 30.62 42.65 64.81
700 (650F) 1,022F (55.27) 21.46 19.32 11.92
1,022F+ 25.33 40.00 25.00 5.0
C
5
+, API/wt% S 23.70 / 0.54 22.5 / 0.71 26.6 / 0.66 33.3 / 0.33
Continued
Economics:
Investment, estimated (US Gulf Coast, 2000)
Size, bpsd fresh feed 92,000 49,000
$/bpsd typical fresh feed 2,200 3,500 4,200 5,200
Utilities, per bbl fresh feed
Fuel red, 10
3
Btu 56.1 62.8 69.8 88.6
Electricity, kWh 8.4 13.9 16.5 22.9
Steam (export), lb 35.5 69.2 97.0 97.7
Water, cooling, gal. 64.2 163 164 248
Installation: Five LC-FINING units are in operation, one LC-FINING Unit is
in construction and two LC-FINING Units are in engineering.
Hydrocracking
Application: Convert a wide variety of feedstocks including vacuum
deep-cut gas oil, coker gas oils, de-asphalted oil (DAO), and FCC cy-
cle oils into high-quality, low-sulfur fuels using ExxonMobil Research
and Engineering Companys (EMRE) moderate pressure hydrocracking
(MPHC) process.
Products: Products include a wide range of high-quality, low-sulfur dis-
tillates and blending stocks including LPG, high-octane gasoline, high-
quality reformer naphtha. Unconverted bottoms product from the MPHC
unit is very low in sulfur and is an excellent feedstock for uid catalytic
cracking (FCC), lube-oil basestock production, steam cracking and low-
sulfur fuel oil.
Description: The process uses a multiple catalyst system in multi-bed
reactor(s) that incorporates proprietary advanced quench and redistri-
bution internals (Spider Vortex). Heavy hydrocarbons and recycle gas
are preheated and contact the catalyst in the trickle-phase xed-bed
reactor(s). Reactor efuent is ashed in high- and low-temperature sep-
arators. An amine scrubber removes H
2
S from the recycle gas before it
gets compressed and re-circulated back to the unit. An optimized, low
cost stripper/fractionator arrangement is used for product recovery.
When higher-quality distillates are required, the addition of a low-
cost, highly integrated distillate post-treating unit (PTU) can be incor-
porated in the design to meet or exceed high-pressure hydrocracking
product quality at lower capital cost and hydrogen consumption
Operating conditions and yields: Typical operating conditions on a Mid-
dle East VGO for a once-through MPHC operation are shown:
Operation conditions:
Conguration MPHC MPHC MPHC
Nominal conversion, % 35 50 50
H
2
pressure, psig 800 800 1,250
Yields:
Naphtha, wt% 4 10 10
Kero/jet, wt% 6 10 10
Diesel, wt% 22 26 27
LSGO (FCC feed), wt% 65 50 50
H
2
consumption, wt% 1.0 1.5 1.3 1.8 1.5 2.0
Product quality:
Kero sulfur, wppm 20 200 20 200 20 200
Kero smoke Pt, mm 13 18 15 20 17 22
Diesel sulfur, wppm 30 500 30 300 30 200
Diesel cetane no. 45 50 47 52 50 55

Continued
Utilities, per bbl of feed:
Electric power, kW 4.1 7.2
Fuel (absorbed), Btu 67,100 69,600
Steam, MP (export), lb (15.9) (21.1)
Water, cooling, gal 101 178
Wash water, gal 1.5 2.2
Lean amine, gal 36.1 36.1
EMREs MPHC process is equally amenable to revamp or grassroots
applications. EMRE has an alliance with Kellogg Brown & Root (KBR) to
provide MPHC technology to reners.
Economics: Investment $/ bpsd 2,000 3,000
Installation: Four operating units; two in construction.
Hydrocracking
Application: Topses hydrocracking process (ULTRACRACKING) can be
used to convert straight run vacuum gas oils and heavy cracked gas oils
to high quality sulfur-free naphtha, kerosene, diesel, and FCC feed,
meeting current and future regulatory requirements. In addition, high VI
lube stocks and petrochemical feedstock can be produced to increase
the renerys protability.
Product: By proper selection of operating conditions, process congu-
ration, and catalysts, the Topse ULTRACRACKING process can be de-
signed for high conversion to produce high smoke point kerosine and
high cetane diesel. The process can also be designed for lower conver-
sion/upgrade mode to produce low sulfur FCC feed with the optimum
hydrogen uptake or high VI (>145) lube stock. The FCC gasoline pro-
duced from a Topse ULTRACRACKING unit does not require post-treat-
ment for sulfur removal.
Description: The ULTRACRACKING process uses well proven co-current
downow xed bed reactors with state - of - the - art reactor internals and
catalysts. The process uses recycle hydrogen and can be congured in
partial conversion once-through feed mode or with recycle of partially
converted oil to obtain 100% conversion to diesel and lighter prod-
ucts. Topses zeolitic and amorphous hydrocracking catalysts have been
proven in several commercial hydrocrackers.
Operating conditions: Typical operating pressure and temperatures
range from 55 to 170 bar (800 to 2500 psig) and 340 to 420C (645 to
780F).
Installations: One operating licensed hydrocracker. Topse hydrocracking
catalysts are in use in ve hydrocrackers.

Hydrocracking
Application: To convert heavy VGO and other low-cost cracked and ex-
tracted feedstocks into high-value, high-quality products, such as low-
sulfur diesel, jet fuel, high-octane light gasoline and reformer feed via
the Shell Hydrocracking Process. Unconverted or recycle oil are prime
feeds for secondary processing in FCCUs, lube base oil plants and eth-
ylene crackers.
Description: Heavy feed hydrocarbons are preheated with reactor efu-
ent (1). Fresh hydrogen is combined with recycle gas from the cold high-
pressure separator, preheated with reactor efuent, and then heated in
a single-phase furnace. Reactants pass via trickle ow through multi-bed
reactor(s) containing proprietary pre-treat, cracking and post-treat cata-
lysts (2). Interbed ultra-at quench internals and high dispersion nozzle
trays combine excellent quench, mixing and liquid ow distribution at
the top of each catalyst bed while maximizing reactor volume utiliza-
tion. After cooling by feed streams, reactor efuent enters a separator
system. Hot efuent is routed to fractionation (3).
Two-stage, series ow and single-stage unit design congurations
are available including a single-reactor, stacked-bed design suitable for
capacities up to 10,000 tpd in partial or full-conversion modes. The
catalyst systems are carefully tailored for the desired product slate and
catalyst cycle length.
Installations: Over 30 new and revamp designs installed or under de-
sign. Revamps have been implemented in own or other licensors de-
signs usually to debottleneck and increase feed heaviness.
Supplier: Shell Global Solutions International B.V.
Hydrocracking
Application: Convert a wide variety of feedstocks into lower-molecular-
weight products using the Unicracking and HyCycle Unicracking process.
Feed: Feedstocks include atmospheric gas oil, vacuum gas oil, FCC/RCC
cycle oil, coker gas oil, deasphalted oil and naphtha for production of LPG.
Products: Processing objectives include production of gasoline, jet fuel,
diesel fuel, lube stocks, ethylene-plant feedstock, high-quality FCC feed-
stock and LPG.
Description: Feed and hydrogen are contacted with catalysts, which in-
duce desulfurization, denitrogenation and hydrocracking. Catalysts are
based upon both amorphous and molecular-sieve containing supports.
Process objectives determine catalyst selection for a specic unit. Prod-
uct from the reactor section is condensed, separated from hydrogen-rich
gas and fractionated into desired products. Unconverted oil is recycled
or used as lube stock, FCC feedstock or ethylene-plant feedstock.
Yields: Example:
FCC cycle Vacuum Fluid coker
Feed type oil blend gas oil gas oil
Gravity, API 27.8 22.7 8.4
Boiling, 10%, F 481 690 640
End pt., F 674 1,015 1,100
Sulfur, wt% 0.54 2.4 4.57
Nitrogen, wt% 0.024 0.08 0.269
Principal products Gasoline Jet Diesel FCC feed
Yields, vol% of feed
Butanes 16.0 6.3 3.8 5.2
Light gasoline 33.0 12.9 7.9 8.8
Heavy naphtha 75.0 11.0 9.4 31.8
Jet fuel 89.0
Diesel fuel 94.1 33.8
600F + gas oil 35.0
H
2
consump., scf/bbl 2,150 1,860 1,550 2,500
Economics: Example:
Investment, $ per bpsd capacity 2,0004,000
Fuel, 10
3
Btu 70120
Electricity, kWh 710
Installation: Selected for 161 commercial units, including several converted
from competing technologies. Total capacity exceeds 3.6 million bpsd.
Licensor: UOP LLC.

Hydrocracking, resid
Application: High-conversion catalytic hydrocracking of petroleum resid-
ua, heavy oil and bitumen, using a molecular-sized, dispersed catalyst.
The (HC)
3
dispersed catalyst may also be used as an additive in existing
ebullated-bed resid hydrocrackers, to signicantly reduce process foul-
ing, and to increase feedstock exibility and conversion.
Process description: The (HC)
3
hydrocracking process battery limits in-
clude a unit for adding ppm levels of the proprietary liquid catalyst pre-
cursor in the resid feed, from which a molecular-sized catalyst is created
in-situ. The battery limits also include hydrogen and feed heaters, one
or two stages of gas-liquid, back-mixed reactors operating at constant
catalyst activity throughout the liquid phase, a product separator for
bottoms recycle, inline distillate hydrotreating and recycle gas cleaning.
Liquid mixing and reactor temperature homogeneity are ensured via a
recirculation pump at the bottom of the reactor. The process does not
suffer from pressure drop or fouling, and produces a constant-quality
hydrocracked product. Run lengths of ve or more years between turn-
arounds are expected with the (HC)
3
technology.
H
2
partial pressure, psi 1,000 2000
LHSV, hr
1
0.4 2.0
Investment and operating costs: (2004 US Gulf Coast basis)
Capital investment: $2,5004,000 per bpsd [for (HC)
3

standalone process]
Utilities: per bbl of feed
Fuel, 10
3
Btu 30 90
Power, kWh 5 12
Water, cooling (20F rise), gal 30 70
Catalyst makeup, $ 0.4 1.5 for
standalone hydrocracker
For (HC)
3
catalyst as an additive to improve ebullated bed operation:
Capital cost is minimal; expect no increase in net, combined catalyst
costs [that is, supported catalyst plus (HC)
3
additive].
Installations: The (HC)
3
additive is expected to be utilized in a commer-
cial ebullated bed plant in 2004.
Licensor: Hydrocarbon Technologies, Inc.
Hydrocracking/hydrotreating
VGO/DAO
Application: The T-Star Process is an ebullated-bed process for the
hydrotreatment / hydrocracking of vacuum gas oils. The T-Star Process
is best suited for difcult feedstocks (coker VGO, DAO), high-severity
operations and applications requiring a long run length.
Description: A T-Star process ow diagram, which includes inte-
grated mid-distillate hydrotreating, is shown above. The typical
T-Star battery limits include oil/hydrogen red heaters, an advanced hot
high-pressure design for product separation and for providing recycle
to the ebullating pump, recycle gas scrubbing and product separation.
Catalyst is replaced periodically from the reactor, without shutdown.
This ensures the maintenance of constant, optimal catalyst activity and
consistent product slate and quality. After high-pressure recovery of
the efuent and recycle gas, the products are separated and stabilized
through fractionation. A T-Star unit can operate for four-year run lengths
with conversion in the 20 50% range and hydrodesulfurization in the
93 99% range.
Hydrogen partial pressure, psi 6001,500
LHSV, hr
1
0.53.0
VGO conversion, % 2060
Examples: In Case 1, a deep-cut Arab heavy VGO is processed at 40 wt%
conversion with objectives of mild conversion and preparing specica-
tion diesel and FCC unit feed. In Case 2, a VGO blend containing 20%
coker material is processed at lower conversion to also obtain specica-
tion FCC unit feedstock and high-quality diesel.
Economics: Basis 2002 US Gulf Coast
Investment in $ per bpsd 1,2002,500
Utilities, per bbl of feed
Fuel, 10
3
Btu 60
Power, kWh 3
Catalyst makeup, $ 0.050.20
Installation: The T-Star process is commercially demonstrated based on
the ebullated-bed reactor. Axens has licensed more than 1.5 MMbpsd
of capacity in gas oil, VGO and residue. Axens has seven commercially
operating ebullated-bed units and one start-up.
Reference: A novel approach to attain new fuel specications, Petro-
leum Technology Quarterly, Winter 1999/2000.
Licensor: Axens.
Hydrodearomatization
Application: Topses two-stage hydrodesulfurization hydrodearomati-
zation (HDS/HDA) process is designed to produce low-aromatics distil-
late products. This process enables reners to meet the new, stringent
standards for environmentally friendly fuels.
Products: Ultra-low sulfur, ultra-low nitrogen, low-aromatics diesel, ker-
osine and solvents (ultra-low aromatics).
Description: The process consists of four sections: initial hydrotreating, in-
termediate stripping, nal hydrotreating and product stripping. The initial
hydrotreating step, or the rst stage of the two-stage reaction process,
is similar to conventional Topse hydrotreating, using a Topse high-activ-
ity base metal catalyst such as TK-573 to perform deep desulfurization
and deep denitrication of the distillate feed. Liquid efuent from this
rst stage is sent to an intermediate stripping section, in which H
2
S and
ammonia are removed using steam or recycle hydrogen. Stripped distil-
late is sent to the nal hydrotreating reactor, or the second stage. In
this reactor, distillate feed undergoes saturation of aromatics using a Top-
se noble metal catalyst, either TK-907/TK-911 or TK-915, a high-activity
dearomatization catalyst. Finally, the desulfurized, dearomatized distillate
product is steam stripped in the product stripping column to remove H
2
S,
dissolved gases and a small amount of naphtha formed.
Like the conventional Topse hydrotreating process, the HDS/HDA
process uses Topses graded bed loading and high-efciency patented
reactor internals to provide optimum reactor performance and catalyst
use leading to the longest possible catalyst cycle lengths. Topses high
efciency internals have a low sensitivity to unlevelness and are designed
to ensure the most effective mixing of liquid and vapor streams and max-
imum utilization of catalyst. These internals are effective at high liquid
loadings, thereby enabling high turndown ratios. Topses graded-bed
technology and the use of shape-optimized inert topping and catalysts
minimize the build-up of pressure drop, thereby enabling longer catalyst
cycle length.
Operating conditions: Typical operating pressures range from 20 to 60
barg (300 to 900 psig), and typical operating temperatures range from
320C to 400C (600F to 750F) in the rst stage reactor, and from
260C to 330C (500F to 625F) in the second stage reactor. An ex-
ample of the Topse HDS/HDA treatment of a heavy straight-run gas oil
feed is shown below:
Feed Product
Specic gravity 0.86 0.83
Sulfur, ppmw 3,000 1
Nitrogen, ppmw 400 <1
Total aromatics, wt% 30 <10
Cetane index, D-976 49 57
Continued
References: Cooper, Hannerup and Sgaard-Andersen, Reduction of
aromatics in diesel, Oil and Gas, September 1994.
de la Fuente, E., P. Christensen, and M. Johansen, Options for meet-
ing EU year 2005 fuel specications, Fourth ERTC, November 1999.
Installation: A total of ve, two in Europe and three in North America.
Hydrodearomatization, continued
Hydrodesulfurization
Application: The ISAL process enables reners to meet the worlds most
stringent specications for gasoline sulfur while also controlling product
octane.
This moderate-pressure, xed-bed hydroprocessing technology de-
sulfurizes gasoline-range olenic feedstocks and selectively recongures
lower octane components to control product octane. This process can
be applied as a stand-alone unit or as part of an overall integrated ow
scheme for gasoline desulfurization.
Description: The ow scheme of the ISAL unit is very similar to that of
a conventional hydrotreater. The naphtha feed is mixed with hydrogen-
rich recycle gas and processed across xed catalyst beds at moderate
temperatures and pressures. Following heat exchange and separation,
the reactor efuent is stabilized. The similarity of an ISAL unit to a con-
ventional naphtha hydrotreating unit makes new unit and revamp im-
plementation both simple and straightforward. In addition to new unit
designs, the technology has been applied both to idle reforming and
hydrotreating units.
Product quality: The ISAL units operation can be adjusted to achieve
various combinations of octane recovery and yield. Yield/octane rela-
tionships for an integrated ow scheme processing an FBR FCC naphtha
containing 420 wppm sulfur and 24 wt% olens are:
Yield, vol% 99.5 97.2
Sulfur, wppm 10 10
(R + M) / 2 change 2 0
Economics: The capital and operating costs of an ISAL unit are slightly
higher than those of a typical naphtha hydrotreating unit. With this pro-
cess, reners benet from the ability to produce a higher-octane product
at incremental additional operating cost primarily related to additional
hydrogen consumption.
Installation: Four ISAL applications have been implemented in the
US, with an additional three ISAL units currently in the process design
stage.
Licensor: UOP LLC (in cooperation with PDVSA-INTEVEP).
HydrodesulfurizationUDHDS
Application: A versatile family of premium distillates technologies is
used to meet all current and possible future premium diesel upgrad-
ing requirements. Ultra-deep hydrodesulfurization (UDHDS) process can
produce distillate products with sulfur levels below 10 wppm from a
wide range of distillate feedstocks.
Products: High volume yield of ultra-low-sulfur distillate is produced.
Cetane and API gravity uplift, together with the reduction of polyaro-
matics to less than 6 wt% or as low as 2 wt%, can be economically
achieved.
Description: The UDHDS reactor and catalyst technology is offered
through Akzo Nobel Catalysts bv. A single-stage, single-reactor process
incorporates proprietary high-performance distribution and quench in-
ternals. Feed and combined recycle and makeup gas are preheated and
contact the catalyst in a downow, concurrent xed-bed reactor. The
reactor efuent is ashed in a high- and a low-pressure separator. An
amine-absorber tower is used to remove H
2
S from the recycle gas. In
the example shown, a steam stripper is used for nal product recovery.
The UDHDS technology is equally applicable to revamp and grassroots
applications.
Economics:
Investment (Basis: 25,00035,000 bpsd, 1Q 2000 US Gulf Coast)
New unit, $ per bpsd 1,000 to 1,800
Installation: Over 60 distillate upgrading units have applied the Akzo
Nobel ultra-deep HDS technology. Twenty-ve of these applications pro-
duce, or will produce, <10ppm sulfur, using UDHDS technology.
Reference: Technology for premium distillates, ERTC Low-Sulfur Fuels
Workshop, February/March 2002, London.
Licensor: Akzo Nobel Catalysts bv.
Hydrofinishing
Application: Deeply saturate single- and multiple-ring aromatics in base-
oil feedstocks. The product will have very low-aromatics content, very
high-oxidation stability and high thermal stability.
Description: ISOFINISHING catalysts hydrogenate aromatics at relative-
ly low reaction temperatures. They are especially effective in complete
polyaromatics saturationa reaction that is normally equilibrium limited.
Typical feedstocks are the efuent from a dewaxing reactor, efuent from
hydrated feeds or solvent-dewaxed feedstocks. The products are highly
stabilized base-oil, technical-grade white oil or food-grade white oil.
As shown in the simplied ow diagram, feedstocks are mixed with
recycle hydrogen and fresh makeup hydrogen, heated and charged to a
reactor containing ISOFINISHING Catalyst (1). Efuent from the nishing
reactor is ashed in high-pressure and low-pressure separators (2, 3).
A very small amount of light products are recovered in a fractionation
system (4).
Yields: For a typical feedstock, such as dewaxing reactor efuent, the
yield can be >99%. The chemical-hydrogen consumption is usually very
low, less than ~10 Nm
3
/m
3
oil.
Economics:
Investment: For a stand-alone ISOFINISHING Unit, the ISBL capital is
about 3,000 5,000 $/bpsd, depending on the pressure
level and size.
Utilities: Typical per bbl feed:
Power, kW 2.6
Fuel, kcal 3.4 x 10
3

Installation: Twenty units are in various stages of operation, construction
or design.
Reference: NPRA Lubricants & Waxes Meeting, November 2002, Hous-
ton, Paper LW-02-128.
Hydrofinishing/hydrotreating
Application: Process to produce nished lube-base oils and special oils.
Feeds: Dewaxed solvent or hydrogen-rened lube stocks or raw vacuum
distillates for lubricating oils ranging from spindle oil to machine oil and
bright stock.
Products: Finished lube oils (base grades or intermediate lube oils) and
special oils with specied color, thermal and oxidation stability.
Description: Feedstock is fed together with make-up and recycle hydro-
gen over a xed-bed catalyst at moderate temperature and pressure.
The treated oil is separated from unreacted hydrogen, which is recycled.
Very high yields product are obtained.
For lube-oil hydronishing, the catalytic hydrogenation process is
operated at medium hydrogen pressure, moderate temperature and low
hydrogen consumption. The catalyst is easily regenerated with steam
and air.
Operating pressures for hydrogen-nishing processes range from
25 to 80 bar. The higher-pressure range enables greater exibility with
regard to base-stock source and product qualities. Oil color and thermal
stability depend on treating severity. Hydrogen consumption depends
on the feed stock and desired product quality.
Utility requirements (typical, Middle East Crude), units per m
3
of feed:
Electricity, kWh 15
Steam, MP, kg 25
Steam, LP, kg 45
Fuel oil, kg 3
Water, cooling, m
3
10
Installation: Numerous installations using the Uhde (Edeleanu) propri-
etary technology are in operation worldwide. The most recent reference
is a complete lube-oil production facility licensed to the state of Turk-
menistan.

Hydrogen
Application: To produce hydrogen from light hydrocarbons using steam-
methane reforming.
Feedstock: Natural gas, renery gas, LPG and naphtha.
Product: High-purity hydrogen and steam.
Description: Light hydrocarbon feed (1) is heated prior to passing
through two xed-catalyst beds. Organic sulfur compounds present in
feed gas (e.g., mercaptans) are converted to hydrogen sulde (H
2
S) and
mono-olens in the gas phase are hydrogenated in the rst bed of co-
balt molybdenum oxide catalyst (2). The second bed contains zinc oxide
to remove H
2
S by adsorption. This sulfur-removal stage is necessary to
avoid poisoning of the reforming catalysts. Treated feed gas is mixed
with steam and heated before passing to the reformer where the hydro-
carbons and steam react to form synthesis gas (syngas).
Foster Wheeler supplies proprietary side-red Terrace Wall reform-
ers, with natural draft mode for increased reliability, compact plot layout
with convection section mounted directly above the radiant section and
modular fabrication option. Top-red reformers are options for large
capacity plants.
Syngas containing hydrogen, methane, carbon dioxide (CO
2
), car-
bon monoxide (CO) and water leaves the reformer and passes through
the waste-heat boiler to the shift reactor (3) where most of the CO is
converted to CO
2
and hydrogen by reaction with steam. For heavier
feedstocks, pre-reforming is used for conversion of feedstock upstream
of the reformer.
The syngas is cooled through a series of heat-recovery exchangers
before free water is recovered in a knockout drum. The resultant raw
hydrogen stream passes to the pressure swing adsorption (PSA) unit
for purication (4) to 99.9% hydrogen product quality. Tail gas from
the PSA unit provides a substantial proportion of the ring duty for the
reformer. The remaining fuel is supplied from feed gas or other sources
(e.g. renery fuel gas).
Demineralized water make-up is deaerated, mixed wth recovered
condensate and preheated through a series of heat recovery exchangers,
before passing to the steam drum. Saturated and superheated steam is
raised by heat exchange with the reformed gas and ue gas in the con-
vection section of the reformer. Steam export quantities can be varied
between 1,250 to 5,750 lbs per MMscfd of hydrogen produced using
air pre-heat and auxiliary ring options.
Economics: Plant design congurations are optimized to suit the clients
economic requirements, using discounted cash-ow modeling to estab-
lish the lowest lifecycle cost of hydrogen production.

Continued
Investment: 10 100 MMscfd, 1st Q 2004, USGC $7 55 million
Utilities, typical per MMscfd of hydrogen produced
(natural gas feedstock):
Feed + fuel, lb 960
Water, demineralized, lb 4,420
Steam, export, lb 3,320
Water, cooling, US gal 1,180
Electricity, kWh 12
Reference: Ward, R. D. and N. Sears, Hydrogen plants for the new mil-
lenium, Hydrocarbon Engineering, Vol. 7, June 2002.
Installation: Over 100 plants, ranging from 1 MMscfd to 95 MMscfd
in a single-train conguration and numerous multi-train congurations.
Licensor: Foster Wheeler.
Hydrogen, continued
Hydrogen
Application: Production of hydrogen ( H
2
) from hydrocarbon (HC) feed-
stocks, by steam reforming.
Feedstocks: Ranging from natural gas to heavy naphtha as well as po-
tential renery offgases. Many recent renery hydrogen plants have
multiple feedstock exibility, either in terms of back-up or alternative
or mixed feed. Automatic feedstock change-over has also successfully
been applied by TECHNIP in several modern plants with multiple feed-
stock exibility.
Description: The generic owsheet consists of feed pretreatment, pre-
reforming (optional), steam-HC reforming, shift conversion and hydro-
gen purication by pressure swing adsorption (PSA). However, it is often
tailored to satisfy specic requirements.
Feed pretreatment normally involves removal of sulfur, chlorine and
other catalyst poisons after preheating to 350C to 400C.
The treated feed gas mixed with process steam is reformed in a red
reformer (with adiadatic pre-reformer upstream, if used) after neces-
sary superheating. The net reforming reactions are strongly endother-
mic. Heat is supplied by combusting PSA purge gas, supplemented by
makeup fuel in multiple burners in a top-red furnace.
Reforming severity is optimized for each specic case. Waste heat
from reformed gas is recovered through steam generation before the
water-gas shift conversion. Most of the carbon monoxide is further con-
verted to hydrogen. Process condensate resulting from heat recovery
and cooling is separated and generally reused in the steam system after
necessary treatment. The entire steam generation is usually on natural
circulation, which adds to higher reliability. The gas ows to the PSA unit
that provides high-purity hydrogen product (up to < 1ppm CO) at near
inlet pressures.
Typical specic energy consumption based on feed + fuel export
steam ranges between 3.0 and 3.5 Gcal / KNm
3
( 330 370 Btu / scf ) LHV,
depending upon feedstock, plant capacity, optimization criteria and
steam-export requirements. Recent advances include integration of hy-
drogen recovery and generation, and recuperative (post-)reforming also
for capacity retrots.
Installations: TECHNIP has been involved in over 240 hydrogen plants
worldwide, covering a wide range of capacities. Most installations are
for renery application with basic features for high reliability and opti-
mized cost.
Licensor: Technip.
Hydrogen
Application: Produce hydrogen for renery hydrotreating and hydro-
cracking or other renery, petrochemical and industrial applications.
Feed: Natural gas, renery offgas, LPG/butane, light naphtha and mul-
tiple feedstock.
Product: High-purity hydrogen (>99.9%). CO, CO
2
and/or electricity
may also be produced separately for byproduct credit.
Description: The feedstock (natural gas, for example) is desulfurized (1),
mixed with steam and converted to synthesis gas in the reformer (2) over
nickel catalysts at 2040 bar pressure and temperatures of 800 900C.
The Uhde steam reformer is a top-red reformer, which has tubes
made of centrifugally cast alloy steel and a proprietary cold outlet
manifold system to enhance reliability. Subsequent high-pressure steam
generation (3) and superheating permit maximum process heat recovery
to achieve an optimized energy-efcient process.
The carbon monoxide (CO) shift occurs in a single-stage, adiabatic high-
temperature reactor (4). Pressure swing adsorption (5) is a well-established
purication step to obtain high-purity hydrogen (99.9 % and higher).
The Uhde reformer design with the unique proprietary cold outlet
manifold system enables construction and operation of world-scale re-
formers with hydrogen capacities up to 220,000 Nm
3
/ h (197 MMscfd)
in single-train conguration.
Economics: Depending on the individual plant concept, the typical con-
sumption gure (feed + fuel steam) is approximately 3.15 Gcal /1,000
Nm
3
(335 MMBtu/MMscf).
Installations: Uhde has recently commissioned two of the worlds larg-
est hydrogen plants for SINCOR C.A., Venezuela (2 x 98,000 Nm
3
/ h or
2 x 88 MMscfd ) and Shell Canada Ltd., Canada (2 x 130,000 Nm
3
/ h or
2 x 116 MMscfd ). More than 60 Uhde reformers have been constructed
worldwide.
References: Larsen, J., M. Michel, J. Zschommler (Uhde), M. Whysall
and S. Vanheertum (UOP), Large-scale hydrogen plants, Uhde and
UOPs experience, AIChE 2003 Spring Meeting, New Orleans, March
30 April 3, 2003.
Michel, M., Design and Engineering Experience with Large-Scale
Hydrogen Plants, Oil Gas European Magazine, Vol. 30 (2004) No. 2 in:
Erdl Erdgas Kohle Vol. 120 (2004) No. 6, pp. OG 85 88.

Hydrogenation
Application: CDHydro is used to selectively hydrogenate diolens in
the top section of a hydrocarbon distillation column. Additional appli-
cationsincluding mercaptan removal, hydroisomerization and hydro-
genation of olens and aromatics are also available.
Description: The patented process CDHydro combines fractionation
with hydrogenation. Proprietary devices containing catalyst are in-
stalled in the fractionation columns top section (1). Hydrogen is in-
troduced beneath the catalyst zone. Fractionation carries light com-
ponents into the catalyst zone where the reaction with hydrogen
occurs. Fractionation also sends heavy materials to the bottom. This
prevents foulants and heavy catalyst poisons in the feed from con-
tacting the catalyst. In addition, clean hydrogenated reux contin-
uously washes the catalyst zone. These factors combine to give a
long catalyst life. Additionally, mercaptans can react with diolens to
make heavy, thermally-stable suldes. The suldes are fractionated
to the bottoms product. This can eliminate the need for a separate
mercaptan removal step. The distillate product is ideal feedstock for
alkylation or etherication processes.
The heat of reaction evaporates liquid, and the resulting vapor is
condensed in the overhead condenser (2) to provide additional reux.
The natural temperature prole in the fractionation column results in a
virtually isothermal catalyst bed rather than the temperature increase
typical of conventional reactors.
The CDHydro process can operate at much lower pressure than
conventional processes. Pressures for CDHydro are typically set by the
fractionation requirements. Additionally, the elimination of a separate
hydrogenation reactor and hydrogen stripper offers signicant capital
cost reduction relative to conventional technologies.
Feeding CDHydro with reformate and light-straight run for benzene
saturation provides the rener with increased exibility to produce RFG.
Isomerization of the resulting C
5
/ C
6
overhead stream provides higher
octane and yield due to reduced benzene and C
7
+
content compared to
typical isomerization feedstocks.
Economics: Fixed-bed hydrogenation requires a distillation column fol-
lowed by a xed-bed hydrogenation unit. CDHydro eliminates the xed-
bed unit by incorporating catalyst in the column. When a new distilla-
tion column is used, capital cost of the column is only 5% to 20% more
than for a standard column depending on the CDHydro application.
Elimination of the xed-bed reactor and stripper can reduce capital cost
by as much as 50%.
Installation: Twenty-seven CDHydro units are in commercial operation
for C
4
, C
5
, C
6
and benzene hydrogenation applications. Fourteen units
have been in operation for more than ve years and total commer-
Continued
cial operating time now exceeds 100 years for CDHydro technologies.
Twelve additional units are currently in engineering / construction.
Licensor: CDTECH.
Hydrogenation, continued
HydrogenHTCR-based
Application: Production of hydrogen from hydrocarbon feedstocks such
as: natural gas, LPG, naphtha, renery offgases, etc., using the Haldor
Topse Convective Reformer (HTCR). Plant capacities range up to 20,000
Nm
3
/h (20 MM scfd), and hydrogen purity from 99.5% to 99.999% is
attainable. This is achieved without steam export.
Description: The HTCR-based hydrogen plant can be tailor-made to suit
the customers needs with respect to feedstock exibility. A typical plant
comprises the following: The hydrocarbon feedstock is desulfurized.
Subsequent, process steam is added, and the mixture is fed to the HTCR
where the hydrocarbons are converted to CO, CO
2
and H
2
by steam
reforming. Process gases are reacted in a CO shift converter and puried
by pressure swing absorption (PSA) to obtain product-grade hydrogen.
PSA offgases are consumed as fuel in the HTCR. Excess heat in the plant
is efciently used for process heating and process steam generation.
A unique feature of the HTCR is its high thermal efciency. Product gas
and ue gas are both cooled to 600 C (1,100 F ) by providing heat to the
reforming reaction. The high-thermal efciency is used to design energy-ef-
cient hydrogen plants based on the HTCR without any steam export.
Economics: HTCR-based hydrogen plants provide the customer with a
low investment and low operating cost option for hydrogen production.
The plant can be supplied skid-mounted providing a short erection
time. The plants have high exibility, reliability and safety. Fully auto-
mated operation, startup and shutdown allow minimum operator at-
tendance. Net energy efciency of 3.4 to 3.6 Gcal / KNm
3
H
2
is achieved
depending on size and feedstock (360 380 Btu /scf).
Installations: Twenty-seven HTCR units are in operation.

HydrogenHTER-p based
Application: Topses proprietary and patented HTER-p (Haldor Top-
se Exchange Reformer parallel installation) technology is a revamp
option for production increase in a steam-reforming-based hydrogen
plant. The technology allows hydrogen capacity increases of more than
25%. This option is especially advantageous because the signicant ca-
pacity expansion is possible with minimal impact on the existing tubular
reformer, which usually is the plant bottleneck.
Description: The HTER-p is installed in parallel with the steam methane
reformer (SMR) and fed independently with desulfurized feed taken
upstream the reformer section. This enables individual adjustment of
feed rate and steam-to-carbon ratio to obtain the desired conversion.
The hydrocarbon feed is reformed over a catalyst bed installed in the
HTER-p. Process efuent from the SMR is transferred to the HTER-p
and mixed internally with the product gas from the HTER-p catalyst.
The process gas supplies the required heat for the reforming reaction
in the tubes of the HTER-p. Thus, no additional ring is required for the
reforming reactions in the HTER-p.
Economics: An HTER-p offers a compact and cost-effective hydrogen
capacity expansion. The investment cost is as low as 60% of that for a
new hydrogen plant. Energy consumption increases only slightly. For a
25% capacity increase, the net energy consumption is 3.13 Gcal / kNm
3
H
2
(333 MM Btu / scf H
2
).
References: Dybkjr, I., and S. W. Madsen, Novel Revamp Solutions
for Increased Hydrogen Demands, Eighth European Rening Technol-
ogy Conference, November 1719, 2003, London, UK

HydrogenMethanol-to-Shift
Application: Topses proprietary Methanol-to-Shift technology is a re-
vamp option for hydrogen production increase for a reforming-based
hydrogen plant. This technology can raise hydrogen production ca-
pacity by more than 25%. The capacity expansion is exible and can
be changed in very short time; the technology is suitable for capacity
peak shaving and offers the rener higher feedstock and product slate
exibility.
Description: Additional hydrogen is produced by reforming of methanol
over Topses novel dual-function catalystLK-510. When installed in the
existing CO shift converter and fed simultaneously with methanol and re-
formed gas, the LK-510 catalyst promotes both the conversion of CO with
steam to H
2
and CO
2
and the reforming of methanol to H
2
and CO
2
.
Methanol from a day tank is pumped to a steam-heated evaporator
and fed as vapor to the existing CO shift converter, now loaded with
the LK-510 catalyst. In most cases, it will be necessary to revamp the
PSA unit for the additional capacity and to check the equipment down-
stream of the CO shift converter and modify as required.
Economics: The Methanol-to-Shift revamp technology is a low-invest-
ment option for hydrogen capacity increase and is rapid to install. The
total investment cost is less than 40% of that of a new hydrogen plant.
Methanol consumption is approximately 0.54 kg/Nm
3
hydrogen (0.03
lb/scf H
2
).
References: Dybkjr, I., and S. W. Madsen, Novel Revamp Solutions
for Increased Hydrogen Demands, Eighth European Rening Technol-
ogy Conference, November 1719, 2003, London, UK.

Hydrogenrecovery
Application: To recover and purify hydrogen or to reject hydrogen from
renery, petrochemical or gas processing streams using a PRISM mem-
brane. Renery streams include hydrotreating or hydrocracking purge,
catalytic reformer offgas, uid catalytic cracker offgas or fuel gas. Pet-
rochemical process streams include ammonia synthesis purge, methanol
synthesis purge or ethylene offgas. Synthesis gas includes those gener-
ated from steam reforming or partial oxidation.
Product: Typical hydrogen (H
2
) product purity is 9098% and, in some
cases, 99.9%. Product purity is dependent upon feed purity, available
differential partial pressure and desired H
2
recovery level. Typical H
2
re-
covery is 8095% or more.
The hydrocarbon-rich nonpermeate product is returned at nearly
the same pressure as the feed gas for use as fuel gas, or in the case of
synthesis gas applications, as a carbon monoxide (CO) enriched feed to
oxo-alcohol, organic acid, or Fisher-Tropsch synthesis.
Description: Typical PRISM membrane systems consist of a pretreatment
(1) section to remove entrained liquids and preheat feed before gas en-
ters the membrane separators (2). Various membrane separator con-
gurations are possible to optimize purity and recovery, and operating
and capital costs such as adding a second stage membrane separator
(3). Pretreatment options include water scrubbing to recover ammonia
from ammonia synthesis purge stream.
Membrane separators are compact bundles of hollow bers contained in
a coded pressure vessel. The pressurized feed enters the vessel and ows on
the outside of the bers (shell side). Hydrogen selectively permeates through
the membrane to the inside of the hollow bers (tube side), which is at lower
pressure. PRISM membrane separators key benets include resistance to wa-
ter exposure, particulates and low feed to nonpermeate pressure drop.
Membrane systems consist of a pre-assembled skid unit with pres-
sure vessels, interconnecting piping, and instrumentation and are fac-
tory tested for ease of installation and commissioning.
Economics: Economic benets are derived from high-product recoveries
and purities, from high reliability and low capital cost. Additional ben-
ets include relative ease of operation with minimal maintenance. Also,
systems are expandable and adaptable to changing requirements.
Installations: Over 270 PRISM H
2
membrane systems have been com-
missioned or are in design. These systems include over 54 systems in re-
nery applications, 124 in ammonia synthesis purge and 30 in synthesis
gas applications.
Licensor: Air Products and Chemicals, Inc.

Hydrogensteam methane
reforming (SMR)
Application: Production of hydrogen from hydrocarbon feedstocks such
as: natural gas, ethane, LPG, naphtha, renery offgases, etc., using the
Haldor Topse radiant-wall Steam Methane Reformer (SMR). Plant ca-
pacities range from 5,000 Nm
3
/h to more than 200,000 Nm
3
/h hydro-
gen (200+ MMscfd H
2
) and hydrogen purity of up to 99.999+%.
Description: The Haldor Topse SMR-based hydrogen plant is tailor-made
to suit the customers needs with respect to economics, feedstock ex-
ibility and steam export. In a typical Topse SMR-based hydrogen plant,
a mix of hydrocarbon feedstocks or a single feedstock stream is rst de-
sulfurized. Subsequently, process steam is added, and the mixture is fed
to a prereformer. Further reforming is carried out in the Haldor Topse
radiant wall SMR. The process gas is reacted in a medium-temperature
CO shift reactor and puried by pressure swing absorption (PSA) to ob-
tain product-grade hydrogen. PSA offgases are used as fuel in the SMR.
Excess heat in the plant is efciently used for process heating and steam
generation.
The Haldor Topse radiant wall SMR operates at high outlet temper-
atures up to 950C (1,740F). The Topse reforming catalysts allow op-
eration at low steam-to-carbon ratio. Advanced Steam Reforming uses
both high outlet temperature and low steam-to-carbon ratio, which are
necessary for high-energy efciency and low hydrogen production cost.
The Advanced Steam Reforming design is in operation in many indus-
trial plants throughout the world.
Economics: The Advanced Steam Reforming conditions described can
achieve a net energy efciency as low as 2.96 Gcal/kNm
3
hydrogen us-
ing natural gas feed (315 Btu/scf H
2
).
Installations: More than 125 units.
References: Rostrup-Nielsen, J. R. and T. Rostrup-Nielsen, Large scale
hydrogen production, CatTech, Vol. 6, no. 4, 2002.
Dybkjr, I., and S. W. Madsen, Advanced reforming technologies
for hydrogen production, Hydrocarbon Engineering, December/Janu-
ary 1997/1998.
Gl, J.N., and I. Dybkjr, Options for hydrogen production, HTI
Quarterly: Summer 1995.

Hydroprocessing, residue
Application: Produces maximum distillates and low-sulfur fuel oil, or
low-sulfur LR-CCU feedstock, with very tight sulfur, vanadium and CCR
specications, using moving bed bunker and xed-bed technologies.
Bunker units are available as a retrot option to existing xed-bed resi-
due HDS units.
Description: At limited feed metal contents, the process typically uses
all xed-bed reactors. With increasing feed metal content, one or more
moving-bed bunker reactors are added up-front of the xed-bed re-
actors to ensure a xed-bed catalyst life of at least one year. A steady
state is developed by continuous catalyst addition and withdrawal: the
catalyst aging is fully compensated by catalyst replacement, at typically
0.5 to 2 vol% of inventory per day.
An all bunker option, which eliminates the need for catalyst change-
out, is also available. A hydrocracking reactor, which converts the syn-
thetic vacuum gasoil into distillates, can be efciently integrated into the
unit. A wide range of residue feeds, like atmospheric or vacuum residues
and deasphalted oils, can be processed using Shell residue hydropro-
cessing technologies.
Reactor pressures: 100 200 bar 1,450 3,000 psi
Reactor temperatures: 370 420C 700 790F
Yields: Typical yields for an SR HYCON unit on Kuwait feed:
Feedstock SR (95% 520C+) with integrated HCU
Yields: [%wof] [%wof]
Gases C
1
C
4
3 5
Naphtha C
5
165C 4 18
Kero + gasoil 165 370C 20 43
VGO 370 580C 41 4
Residue 580C+ 29 29
H
2
cons. 2 3
Economics: Investment costs for the various options depend strongly on
feed properties and process objectives of the residue hydroprocessing
unit. Investment costs for a typical new single string 5,000 tpsd SR-Hy-
con unit will range from 200 to 300 MM US$; the higher gure includes
an integrated hydrocracker.
Installation: There is one unit with both bunker reactors and xed-bed
reactors, operating on short residue (vacuum residue) at 4,300 tpd or
27 Mbpsd capacity, and two all-xed bed units of 7,700 and 7,000 tpd
(48 and 44 Mbpsd resp.), the latter one in one single string. Commercial
experiences range from low-sulfur atmospheric residues to high-metal,
high-sulfur vacuum residues with over 300-ppmw metals.
Continued
Reference: Scheffer, B., et al, The Shell Residue Hydroconversion Pro-
cess: Development and achievements, The European Rening Technol-
ogy Conference, London, November 1997.
Hydroprocessing, residue, continued
Hydroprocessing, ULSD
Application: A versatile family of ExxonMobil Research and Engineering
Co. (EMRE) process technologies and catalysts are used to meet all cur-
rent and possible future premium diesel requirements.
ULSD HDS Ultra-deep hydrodesulfurization process to produce distil-
late products with sulfur levels below 10 wppm.
HDHC Heavy-distillate mild-hydrocracking process for the reduction of
T90 and T95 boiling points, and high-level density reduction.
MAXSAT High-activity aromatics saturation process for the selective
reduction of polyaromatics under low pressure and tempera-
ture conditions.
CPI Diesel cloud point improvement by selective normal parafn hydro-
cracking (MDDW) or by parafn isomerization dewaxing (MIDW).
Description: EMRE units combine the technologies listed above in
low-cost integrated designs to achieve the necessary product uplift at
minimum investment and operating cost. For ultra-low-sulfur-diesel
hydrodesulfurization (ULSD HDS), a single-stage single-reactor process
can be designed. A small cetane improvement, together with the reduc-
tion of polyaromatics to less than 11 wt.% or as low as 5 wt.%, can be
economically achieved with proper specication of catalyst, hydrogen
partial pressure, space velocity and the installation of high-performance
Spider Vortex internals.
The addition of heavy-diesel hydrocracking (HDHC) function to the
HDS reactor can achieve T95 boiling point reduction together with
higher levels of density and aromatics reduction and greater cetane
improvement.
When feedstock aromatics are very high, or very low aromatics in
the product are desired, a second-stage aromatics saturation (MAXSAT)
system is specied to avoid very high design pressures required for a
single-step base-metal hydrotreating catalyst system. When the distil-
late product must also meet stringent uidity specications, EMRE can
offer either parafn isomerization dewaxing (MIDW) or selective normal
parafn cracking-based dewaxing technologies (MDDW). These can be
closely integrated with ULSD HDS and other functions to achieve the full
upgrading requirements.
The EMRE ULSD technologies are equally amenable to revamp or
grassroots applications. EMRE has an alliance with Kellogg Brown &
Root (KBR) to provide these technologies to reners.
Economics:
Investment: (Basis: 20,00035,000 bpsd, 1st quarter
2004 US Gulf Coast)
New unit, $/bpsd 1,2002,000

Continued
Installation: Nineteen distillate upgrading units have applied the EMRE
ULSD technologies. Twelve of these applications are revamps.
Hydroprocessing, ULSD, continued
Hydrotreating
Application: Hydroprocessing of middle distillates, including cracked
materials (coker/visbreaker gas oils and LCO), using SynTechnology
maximizes distillate yield while producing ultra-low-sulfur diesel (ULSD)
with improved cetane and API gain, reduced aromatics, T95 reduction
and cold-ow improvement through selective ring opening, saturation
and/or isomerization. Various process congurations are available for
revamps and new unit design to stage investments to meet changing
diesel specications.
Products: Maximum yield of improved quality distillate while minimizing
fuel gas and naphtha. Diesel properties include less than 10-ppm sulfur,
with aromatics content (total and/or PNA), cetane, density and T95 de-
pendent on product objectives and feedstock.
Description: SynTechnology includes SynHDS for ultra-deep desulfuri-
zation and SynShift / SynSat for cetane improvement, aromatics satura-
tion and density / T95 reduction. SynFlow for cold ow improvement can
be added as required. The process combines ABB Lummus Globals co-
current and/or patented countercurrent reactor technology with special
SynCat catalysts from Criterion Catalyst Co. LP. It incorporates design
and operations experience from Shell Global Solutions to maximize reac-
tor performance by using advanced reactor internals.
A single-stage or integrated two-stage reactor system provides
various process conguration options and revamp opportunities. In a
two-stage reactor system, the feed, makeup and recycle gas are heated
and fed to a rst-stage cocurrent reactor. Efuent from the rst stage
is stripped to remove impurities and light ends before being sent to the
second-stage countercurrent reactor. When a countercurrent reactor is
used, fresh makeup hydrogen can be introduced at the bottom of the
catalyst bed to achieve optimum reaction conditions.
Operating conditions: Typical operating conditions range from 500
1,000 psig and 600F 750F. Feedstocks range from straight-run gas
oils to feed blends containing up to 70% cracked feedstocks that have
been commercially processed. For example, the SynShift upgrading of
a feed blend containing 72% LCO and LCGO gave these performance
gures:
Feed blend Product
Gravity, API 25 33.1
Sulfur, wt% (wppm) 1.52 (2)
Nitrogen, wppm 631 <1
Aromatics, vol% 64.7 34.3
Cetane index 34.2 43.7
Liquid yield on feed, vol% 107.5

Continued
Economics: SynTechnology encompasses a family of low-to-moder-
ate pressure processes. Investment cost will be greatly dependent on
feed quality and hydroprocessing objectives. For a 30,000 to 35,000-
bpsd unit, the typical ISBL investment cost in US$/bpsd (US Gulf Coast
2000) are:
Revamp existing unit 450 950
New unit for deep HDS 1,100 1,200
New unit for cetane improvement and HDA 1,500 1,600
Installation: SynTechnology has been selected for more than 30 units,
with half of the projects being revamps. Seven units are in operation.
Licensor: ABB Lummus Global, on behalf of the SynAlliance, which in-
cludes Criterion Catalyst and Technologies Co., and Shell Global Solu-
tions.
Hydrotreating, continued
Hydrotreating
Application: Reduction of the sulfur, nitrogen and metals content of
naphthas, kerosines, diesel or gas oil streams.
Products: Low-sulfur products for sale or additional processing.
Description: Single or multibed catalytic treatment of hydrocarbon liq-
uids in the presence of hydrogen converts organic sulfur to hydrogen
sulde and organic nitrogen to ammonia. Naphtha treating normally oc-
curs in the vapor phase, and heavier oils usually operate in mixed-phase.
Multiple beds may be placed in a single reactor shell for purposes of
redistribution and/or interbed quenching for heat removal. Hydrogen-
rich gas is usually recycled to the reactor(s) (1) to maintain adequate hy-
rogen-to-feed ratio. Depending on the sulfur level in the feed, H
2
S may
be scrubbed from the recycle gas. Product stripping is done with either
a reboiler or with steam. Catalysts are cobalt-molybdenum, nickel-mo-
lybdenum, nickel-tungsten or a combination of the three.
Operating conditions: 550F to 750F and 400 psig to 1,500 psig reac-
tor conditions.
Yields: Depend on feed characteristics and product specications. Re-
covery of desired product almost always exceeds 98.5 wt% and usually
exceeds 99%.
Economics:
Utilities, (per bbl feed) Naphtha Diesel
Fuel, 10
3
Btu release 48 59.5
Electricity, kWh 0.65 1.60
Water, cooling (20F rise), gal 35 42
Hydrotreating
Application: CDHydro and CDHDS are used to selectively desulfurize
FCC gasoline with minimum octane loss.
Products: Ultra-low-sulfur FCC gasoline with maximum retention of
olens and octane.
Description: The light, mid and heavy cat naphthas (LCN, MCN, HCN)
are treated separately, under optimal conditions for each. The full-range
FCC gasoline sulfur reduction begins with fractionation of the light
naphtha overhead in a CDHydro column. Mercaptan sulfur reacts quan-
titatively with excess diolens to produce heavier sulfur compounds, and
the remaining diolens are partially saturated to olens by reaction with
hydrogen. Bottoms from the CDHydro column, containing the reacted
mercaptans, are fed to the CDHDS column where the MCN and HCN
are catalytically desulfurized in two separate zones. HDS conditions are
optimized for each fraction to achieve the desired sulfur reduction with
minimal olen saturation. Olens are concentrated at the top of the
column, where conditions are mild, while sulfur is concentrated at the
bottom where the conditions result in very high levels of HDS.
No cracking reactions occur at the mild conditions, so that yield
losses are easily minimized with vent-gas recovery. The three product
streams are stabilized together or separately, as desired, resulting in
product streams appropriate for their subsequent use. The two columns
are heat integrated to minimize energy requirements. Typical reformer
hydrogen is used in both columns without makeup compression. The
sulfur reduction achieved will allow the blending of gasoline that meets
current and future regulations.
Catalytic distillation essentially eliminates catalyst fouling because
the fractionation removes heavy-coke precursors from the catalyst zone
before coke can form and foul the catalyst pores. Thus, catalyst life in
catalytic distillation is increased signicantly beyond typical xed-bed
life. The CDHydro/CDHDS units can operate throughout an FCC turn-
around cycle up to ve years without requiring a shutdown to regener-
ate or to replace catalyst. Typical xed-bed processes will require a mid
FCC shutdown to regenerate/replace catalyst, requiring higher capital
cost for feed, storage, pumping and additional feed capacity.
Economics: The estimated ISBL capital cost for a 35,000-bpd CDHydro/
CDHDS unit with 95% desulfurization is $26 million (2000 US Gulf Coast).
Direct operating costsincluding utilities, catalyst, hydrogen and octane
replacementare estimated at $0.04/gal of full-range FCC gasoline.
Installation: Fourteen CDHydro units are in operation treating FCC gaso-
line and 10 more units are currently in engineering/construction. Eight
CDHDS units are in operation with 10 additional units currently in en-
gineering/construction. Forty-six units have been awarded with a total
capacity of one million bpsd.
Licensor: CDTECH.

Hydrotreating
Application: Hydrotreating of light and middle distillates and various gas
oils, including cracked feedstocks (coker naphtha, coker LGO and HGO,
visbreaker gas oil, and LCO) using the ISOTREATING Process for deep
desulfurization, denitrication and aromatics saturation and to produce
low-sulfur naphtha, jet fuel, ultra-low sulfur diesel (ULSD), or improved-
quality FCC feed.
Description: Feedstock is mixed with hydrogen-rich treat gas, heated
and reacted over high-activity hydrogenation catalyst (1). Several CoMo
and NiMo catalysts are available for use in the ISOTREATING Process. One
or multiple beds of catalyst(s), together with Chevron Lummus Globals
advanced high-efciency reactor internals for reactant distribution and
interbed quenching, are used.
Reactor efuent is cooled and ashed (2) producing hydrogen-rich
recycle gas, which, after H
2
S removal by amine (3), is partially used as
quench gas while the rest is combined with makeup hydrogen gas to
form the required treat gas. An intermediate pressure level ash (4) can
be used to recover some additional hydrogen-rich gas from the liquid
efuent prior to the ashed liquids being stripped or fractionated (5) to
remove light ends, H
2
S and naphtha-boiling range material, and/or to
fractionate the higher boiling range materials into separate products.
Operating conditions: Typical reactor operating conditions can range
from 600 1,800 psig and 550 750F, 3501,300 psia hydrogen partial
pressure, and 0.6-3 hr
1
LHSV, all depending on feedstock(s) and prod-
uct quality objective(s).
Yields: Depends on feedstock(s) characteristics and product require-
ments. Desired product recovery is maximized based on required ash
point and/or specic fractionation specication. Reactor liquid product
(350F plus TBP material) is maximized through efcient hydrogenation
with minimum lighter liquid product and gas production. Reactor liq-
uid product (350F plus) yield can vary between 98 vol% from straight-
run gas oil feed to >104 vol% from predominantly cracked feedstock
to produce ULSD (<10 wppm sulfur). Chemical-hydrogen consumption
ranges from 450 900
+
scf/bbl feed.
Economics: Investment will vary depending on feedstock characteristics
and product requirements. For a 40,00045,000-bpsd unit for ULSD,
the ISBL investment cost (US Gulf Coast 2004) is $600900/bpsd for a
revamped unit and $1,5001,800/bpsd for a new unit.
Installation: Currently, there are more than 50 units operating based on
ISOTREATING technology and an additional 14 units in various stages of
engineering.

Hydrotreating
Application: The process was developed for the hydrotreatment for
middle distillates to reduce sulfur and, with the appropriate catalysts,
aromatics to meet the most stringent fuel specications.
Products: Low-sulfur and aromatic middle distillate suitable for diesel.
Description: The essential feature of the SuperTreet process is an in-
terstage separation. The rst-stage catalyst bed is generally lled with
standard HDS catalyst to remove the less refractory sulfur compounds
that accounts for a large part, 80%+, of the contained sulfur in a typical
middle distillate. The hot, high-pressure separation enables removing
H
2
S before introduction of the treated stream to the second reactor. H
2
S
inhibits desulfurization reactions, and so this feature greatly enhances
the effectiveness of the second-stage hydrotreating.
Fresh hydrogen is introduced to the second reactor to further remove
more refractory sulfur compounds such as dibenzothiophenes. The ad-
vent of sulfur-tolerant HDA catalysts means that this nal desulfurization
and dearomatization can both occur in this second reactor. The inter-
mediate removal of H
2
S and the introduction of fresh hydrogen feed
provides a much improved environment for the removal of the most
difcult compounds.
Typical operating conditions: These are very dependent on the nature of
the feed stream and product specication; typically the operating pres-
sure is in the region of 40 bar. The system can be adapted to maximize
the re-use of existing equipment in a revamp situation.
References: McKinley, D. H. and M. A. Wood, Deep DesulfurizationAn
Insight into the Catalyst Bed, AIChE, Spring National Meeting 1995.
Lawrence, R. C., D. H. McKinley and M. A. Wood, Process Develop-
ments in Gasoil Hydrotreating, OAPEC SeminarRening Industry in
the Arab Countries and the Challenges of the 21st Century, 1996.
Lawrence, R. C., D. H. McKinley and M. A. Wood, Further Process
Developments in Gasoil Hydrotreating, Japan Petroleum Institute Con-
ference, Kyoto, 1998.
Licensor: Davy Process Technology Ltd.

Hydrotreating
Application: Topse hydrotreating technology has a wide range of ap-
plications, including the purication of naphtha, distillates and residue,
as well as the deep desulfurization and color improvement of diesel fuel
and pretreatment of FCC and hydrocracker feedstocks.
Products: Ultra-low-sulfur diesel fuel, and clean feedstocks for FCC and
hydrocracker units.
Description: Topses hydrotreating process design incorporates our in-
dustrially proven high-activity TK catalysts with optimized graded-bed
loading and high-performance, patented reactor internals. The combi-
nation of these features and custom design of grassroots and revamp
hydrotreating units result in process solutions that meet the reners
objectives in the most economic way.
In the Topse hydrotreater, feed is mixed with hydrogen, heated
and partially evaporated in a feed/efuent exchanger before it enters
the reactor. In the reactor, Topses high-efciency internals have a low
sensitivity to unlevelness and are designed to ensure the most effective
mixing of liquid and vapor streams and the maximum utilization of the
catalyst volume. These internals are effective at a high range of liquid
loadings, thereby enabling high turndown ratios. Topses graded-bed
technology and the use of shape-optimized inert topping and catalysts
minimize the build-up of pressure drop, thereby enabling longer catalyst
cycle length. The hydrotreating catalysts themselves are of the Topse
TK series, and have proven their high activities and outstanding perfor-
mance in numerous operating units throughout the world. The reactor
efuent is cooled in the feed-efuent exchanger, and the gas and liquid
are separated. The hydrogen gas is sent to an amine wash for removal
of hydrogen sulde and is then recycled to the reactor. Cold hydrogen
recycle is used as quench gas between the catalyst beds, if required. The
liquid product is steam stripped in a product stripper column to remove
hydrogen sulde, dissolved gases and light ends.
Operating conditions: Typical operating pressures range from 20 to 80
barg (300 to 1,200 psig), and typical operating temperatures range from
320C to 400C (600F to 750F).
References: Cooper, B. H. and K. G. Knudsen, Production of ULSD: Cat-
alyst, kinetics and reactor design, World Petroleum Congress, 2002.
de la Fuente, E., P. Christensen and M. Johansen, Options for meet-
ing EU year 2005 fuel specications, ERTC, November 1999.
Patel, R. and K. Knudsen, How are reners meeting the ultra-low-
sulfur diesel challenge, NPRA Annual Meeting, March 2003.
Installation: More than 40 Topse hydrotreating units for the various ap-
plications above are in operation or in the design phase.
Hydrotreating
Application: The IsoTherming process provides reners an economical
means to produce ultra-low-sulfur diesel (ULSD), low-sulfur and low-
nitrogen FCC feedstocks, and other very low-sulfur hydrocarbon prod-
ucts. In addition, IsoTherming can provide a cost-effective approach to
wax and petrolatum hydrogenation to produce food-grade or pharma-
ceutical-grade oil and wax products, and lubestock hydroprocessing for
sulfur reduction and VI improvement.
Products: ULSD, low-sulfur FCC feed, low-sulfur gasoline-kerosine type
products. High-quality lube-oil stock and food- and pharmaceutical-
grade oil and wax.
Description: This process uses a novel approach to introduce hydrogen
into the reactor; it enables much higher space velocities than conven-
tional hydrotreating reactors. The IsoTherming process removes the
hydrogen mass transfer limitation and operates in a kinetically limited
mode since hydrogen is delivered to the reactor in the liquid phase as
soluble hydrogen.
The technology can be installed as a simple pre-treat unit ahead
of an existing hydrotreater reactor or a new stand-alone process unit.
Fresh feed, after heat exchange, is combined with hydrogen in Reactor
One mixer (1). The feed liquid with soluble hydrogen is fed to IsoTherm-
ing Reactor One (2) where partial desulfurization occurs. The stream is
combined with additional hydrogen in Reactor Two Mixer (3), and fed to
IsoTherming Reactor Two (4) where further desulfurization takes place.
Treated oil is recycled (5) back to the inlet of Reactor One. This re-
cycle stream delivers more hydrogen to the reactors and also acts as a
heat sink; thus, a nearly isothermal reactor operation is achieved.
The treated oil from IsoTherming Reactor Two (4) may then be fed
to additional IsoTherming reactors and / or to a trickle hydrotreating re-
actor (6) in the polishing mode to produce an ultra-low-sulfur product.
Operating conditions: Typical diesel IsoTherming conditions are:
Diesel feed IsoTherming Treated product
pre-treat reactor from existing
conventional
reactor
LCO, vol% 40
SR, vol% 60
Sulfur, ppm 7,500 900 5
Nitrogen, ppm 450 50 0
H
2
consumption, scf/bbl 300 150
LHSV, Hr
1
* 5 2.5
Reactor T 30 30
Reactor pressure, psig 1,110 900
*Based on fresh feedrate without recycle

Continued
Economics: Revamp investment (basis 15,000 20,000 bpsd, 1Q 2004,
US Gulf Coast) $400/bpsd diesel
Installation: First commercial diesel unit onstream October 2002.
Licensor: P. D. Licensing, LLC (Process Dynamics, Inc.).
Hydrotreating
Application: The IsoTherming process provides reners an economical
means to produce ultra-low-sulfur diesel (ULSD), low-sulfur and low-
nitrogen FCC feedstocks, and other very low-sulfur hydrocarbon prod-
ucts. In addition, IsoTherming can provide a cost-effective approach to
wax and petrolatum hydrogenation to produce food-grade or pharma-
ceutical-grade oil and wax products, and lubestock hydroprocessing for
sulfur reduction and VI improvement.
Products: ULSD, low-sulfur FCC feed, low-sulfur gasoline-kerosine type
products. High-quality lube-oil stock and food- and pharmaceutical-
grade oil and wax.
Description: This process uses a novel approach to introduce hydrogen
into the reactor; it enables much higher space velocities than conven-
tional hydrotreating reactors. The IsoTherming process removes the
hydrogen mass transfer limitation and operates in a kinetically limited
mode since hydrogen is delivered to the reactor in the liquid phase as
soluble hydrogen.
The technology can be installed as a simple pre-treat unit ahead
of an existing hydrotreater reactor or a new stand-alone process unit.
Fresh feed, after heat exchange, is combined with hydrogen in Reactor
One mixer (1). The feed liquid with soluble hydrogen is fed to IsoTherm-
ing Reactor One (2) where partial desulfurization occurs. The stream is
combined with additional hydrogen in Reactor Two Mixer (3), and fed to
IsoTherming Reactor Two (4) where further desulfurization takes place.
Treated oil is recycled (5) back to the inlet of Reactor One. This re-
cycle stream delivers more hydrogen to the reactors and also acts as a
heat sink; thus, a nearly isothermal reactor operation is achieved.
The treated oil from IsoTherming Reactor Two (4) may then be fed
to additional IsoTherming reactors and / or to a trickle hydrotreating re-
actor (6) in the polishing mode to produce an ultra-low-sulfur product.
Operating conditions: Typical diesel IsoTherming conditions are:
Diesel feed IsoTherming Treated product
pre-treat reactor from existing
conventional
reactor
LCO, vol% 40
SR, vol% 60
Sulfur, ppm 7,500 900 5
Nitrogen, ppm 450 50 0
H
2
consumption, scf/bbl 300 150
LHSV, Hr
1
* 5 2.5
Reactor T 30 30
Reactor pressure, psig 1,110 900
*Based on fresh feedrate without recycle

Continued
Economics: Revamp investment (basis 15,000 20,000 bpsd, 1Q 2004,
US Gulf Coast) $400/bpsd diesel
Installation: First commercial diesel unit onstream October 2002.
Hydrotreating
Application: Hydrodesulfurization, hydrodenitrogenation and hydro-
genation of petroleum and chemical feedstocks using the Unionning
and MQD Unionning processes.
Products: Ultra-low-sulfur diesel fuel; feed for catalytic reforming,
FCC pretreat; upgrading distillates (higher cetane, lower aromatics);
desulfurization, denitrogenation and demetallization of vacuum and at-
mospheric gas oils, coker gas oils and chemical feedstocks.
Description: Feed and hydrogen-rich gas are mixed, heated and contact-
ed with regenerable catalyst (1). Reactor efuent is cooled and separated
(2). Hydrogen-rich gas is recycled or used elsewhere. Liquid is stripped
(3) to remove light components and remaining hydrogen sulde, or frac-
tionated for splitting into multiple products.
Operating conditions: Operating conditions depend on feedstock and
desired level of impurities removal. Pressures range from 500 to 2,000
psi. Temperatures and space velocities are determined by process objec-
tives.
Yields:
Purpose FCC feed Desulf. Desulf. Desulf.
Feed, source VGO + Coker AGO VGO DSL
Gravity, API 17.0 25.7 24.3 32.9
Boiling range, F 400/1,000 310/660 540/1,085 380/700
Sulfur, wt% 1.37 1.40 3 1.1
Nitrogen, ppmw 6,050 400 1,670 102
Bromine number 26
Naphtha, vol% 4.8 4.2 3.9 1.6
Gravity, API 45.0 50.0 54.0 51
Boiling range, F 180/400 C
4
/325 C
4
/356 C
5
/300
Sulfur, ppmw 50 <2 <2 <1
Nitrogen, ppmw 30 <1 <2 <0.5
Distillate, vol% 97.2 97.6 98.0 99.0
Gravity, API 24.0 26.9 27.8 35.2
Boiling range, F 400+ 325/660 300+ 300
Sulfur, wt% 0.025 0.001 0.002 0.001
H
2
consump., scf/bbl 700 350 620 300
Economics:
Investment, $ per bpsd 1,2002,000
Fuel, 10
3
Btu 40100
Installation: Several hundred units installed.
Licensor: UOP LLC.
Hydrotreating
Application: RCD Unionning process reduces the sulfur, nitrogen, Con-
radson carbon, asphaltene and organometallic contents of heavier resi-
due-derived feedstocks to allow them to be used as either specication
fuel oils or as feedstocks for downstream processing units such as hydro-
crackers, uidized catalytic crackers, resid catalytic crackers and cokers.
Feed: Feedstocks range from solvent-derived materials to atmospheric
and vacuum residues.
Description: The process uses a xed-bed catalytic system that operates at
moderate temperatures and moderate to high hydrogen partial pressures.
Typically, moderate levels of hydrogen are consumed with minimal pro-
duction of light gaseous and liquid products. However, adjustments can
be made to the units operating conditions, owscheme conguration or
catalysts to increase conversion to distillate and lighter products.
Fresh feed is combined with makeup hydrogen and recycled gas,
and then heated by exchange and red heaters before entering the
units reactor section. Simple downow reactors incorporating a graded
bed catalyst system designed to accomplish the desired reactions while
minimizing side reactions and pressure drop buildup are used. Reactor
efuent ows to a series of separators to recover recycle gas and liquid
products. The hydrogen-rich recycle gas is scrubbed to remove H
2
S and
recycled to the reactors while nished products are recovered in the
fractionation section. Fractionation facilities may be designed to simply
recover a full-boiling range product or to recover individual fractions of
the hydrotreated product.
Economics:
Investment (basis: 15,000 20,000 bpsd, 2Q 2002, US Gulf Coast)
$ per bpsd 2,000 3,500
Utilities, typical per barrel of fresh feed (20,000 bpsd basis)
Fuel, MMBtu/hr 46
Electricity, kWh 5,100
Steam, HP, lb / hr 8,900
Steam, LP, lb / hr 1,500
Installation: Twenty-six licensed units with a combined licensed capacity
of approximately 900,000 bpsd. Commercial applications have included
processing of atmospheric and vacuum residues and solvent-derived
feedstocks.
Licensor: UOP LLC.

Hydrotreatingaromatic saturation
Application: Hydroprocessing of middle distillates, including cracked
materials (coker/visbreaker gas oils and LCO), using SynTechnology
maximizes distillate yield while producing ultra-low-sulfur diesel (ULSD)
with improved cetane and API gain, reduced aromatics, T95 reduction
and cold-ow improvement through selective ring opening, saturation
and/or isomerization. Various process congurations are available for
revamps and new unit design to stage investments to meet changing
diesel specications.
Products: Maximum yield of improved quality distillate while minimizing
fuel gas and naphtha. Diesel properties include less than 10-ppm sulfur,
with aromatics content (total and/or PNA), cetane, density and T95 de-
pendent on product objectives and feedstock.
Description: SynTechnology includes SynHDS for ultra-deep desulfuri-
zation and SynShift/SynSat for cetane improvement, aromatics satura-
tion and density/T95 reduction. SynFlow for cold ow improvement can
be added as required. The process combines ABB Lummus Globals co-
current and/or patented countercurrent reactor technology with special
SynCat catalysts from Criterion Catalyst Co. LP. It incorporates design
and operations experience from Shell Global Solutions to maximize reac-
tor performance by using advanced reactor internals.
A single-stage or integrated two-stage reactor system provides
various process conguration options and revamp opportunities. In a
two-stage reactor system, the feed, makeup and recycle gas are heated
and fed to a rst-stage cocurrent reactor. Efuent from the rst stage
is stripped to remove impurities and light ends before being sent to the
second-stage countercurrent reactor. When a countercurrent reactor is
used, fresh makeup hydrogen can be introduced at the bottom of the
catalyst bed to achieve optimum reaction conditions.
Operating conditions: Typical operating conditions range from 500
1,000 psig and 600F750F. Feedstocks range from straight-run gas
oils to feed blends containing up to 70% cracked feedstocks that have
been commercially processed. For example, the SynShift upgrading of
a feed blend containing 72% LCO and LCGO gave these performance
gures:
Feed blend Product
Gravity, API 25 33.1
Sulfur, wt% (wppm) 1.52 (2)
Nitrogen, wppm 631 <1
Aromatics, vol% 64.7 34.3
Cetane index 34.2 43.7
Liquid yield on feed, vol% 107.5
Economics: SynTechnology encompasses a family of low-to-moderate
pressure processes. Investment cost will be greatly dependent on feed

Continued
quality and hydroprocessing objectives. For a 30,000 to 35,000-bpsd unit,
the typical ISBL investment cost in US$/bpsd (US Gulf Coast 2002) are:
Revamp existing unit 450950
New unit for deep HDS 1,1001,200
New unit for cetane improvement and HDA 1,5001,600
Installation: Eleven SynTechnology units are in operation with an addi-
tional seven units in design and construction.
Licensor: ABB Lummus Global, on behalf of the SynAlliance, which in-
cludes Criterion Catalyst Co., LP, and Shell Global Solutions.
Hydrotreatingaromatic saturation, continued
Hydrotreatingcatalytic dewaxing
Application: A versatile family of premium distillates technologies is
used to meet all current and possible future premium diesel upgrading
requirements. The addition of selective normal parafn hydrocracking
(CFI) function to the deep hydrodesulfurization (UDHDS) reactor will im-
prove the diesel product cold ow properties for a wide range of waxy
distillate feedstocks.
Products: Ultra-low-sulfur distillate is produced with modest amounts
of lighter products. Low-cloud point, or pour point product quality die-
sel, can be achieved with the CFI processes.
Description: This Akzo-Fina CFI technology is offered through the alli-
ance between Akzo Nobel Catalysts and Fina Research S.A. When the
distillate product must meet stringent uidity specications, Akzo No-
bel can offer this selective normal parafn cracking based CFI dewax-
ing technology. Dewaxing is generally a higher-cost process but delivers
higher total product quality. This technology can be closely integrated
with UDHDS and other functions to achieve the full upgrading require-
ments in low-cost integrated designs. The CFI process uses a single-stage
design even with high levels of heteroatoms in the feed. Akzo Fina CFI
technology is equally applicable to revamp and grassroots applications.
Economics:
Investment (Basis: 15,00025,000 bpsd, 1Q 2000 US Gulf Coast)
Grassroots unit, $ per bpsd 1,000 to 2,000
Installation: Over 17 distillate upgrading units have applied the Akzo
Fina CFI technology.
Reference: MAKFining-Premium Distillates Technology: The future of
distillate upgrading, NPRA Annual Meeting, March 2000, San Antonio.
Licensor: Akzo Nobel Catalysts bv and Fina Research S.A.
Hydrotreating, diesel
Application: Produce ultra-low-sulfur diesel (ULSD) and high-quality die-
sel fuel (low aromatics, high cetane) via Prime-D toolbox of proven state-
of-the-art technology, catalysts and services.
Description: In the basic process, as shown in the diagram, feed and
hydrogen are heated in the feed-reactor efuent exchanger (1) and fur-
nace (2) and enter the reaction section (3), with possible added volume
for revamp cases. The reaction efuent is cooled by the exchanger (1)
and air cooler (4) and separated in the separator (5). The hydrogen-
rich gas phase is treated in an existing or new amine absorber for H
2
S
removal (6) and recycled to the reactor. The liquid phase is sent to the
stripper (7) where small amounts of gas and naphtha are removed and
high-quality product diesel is recovered.
Whether the need is for a new unit or for maximum reuse of existing
diesel HDS units, the Prime-D hydrotreating toolbox of solutions meets
the challenge. Process objectives ranging from low-sulfur, ultra-low-sul-
fur, low-aromatics, and/or high cetane number are met with minimum
cost by:
Selection of the proper catalyst from the HR 400 series, based on
the feed analysis and processing objectives. HR 400 catalysts cover the
range of ULSD requirements with highly active and stable catalysts. HR
426 CoMo exhibits high desulfurization rates at low to medium pres-
sures; HR 448 NiMo has higher hydrogenation activity at higher pres-
sures; and HR 468 NiCoMo is very effective for ULSD in the case of
moderate pressures.
Use of proven, efcient reactor internals, EquiFlow, that allow
near-perfect gas and liquid distribution and outstanding radial tempera-
ture proles.
Loading catalyst in the reactor(s) with the Catapac dense load-
ing technique for up to 20% more reactor capacity. Over 8,000 tons of
catalyst have been loaded quickly and safely in recent years using the
Catapac technique.
Application of Advanced Process Control for dependable opera-
tion and longer catalyst life.
Sound engineering design based on years of R&D, process design
and technical service feedback to ensure the right application of the
right technology for new and revamp projects.
Whatever the diesel quality goalsULSD, high cetane or low aro-
maticsPrime-Ds Hydrotreating Toolbox approach will attain your goals
in a cost-effective manner.
Installation: Over 100 middle distillate hydrotreaters have been li-
censed or revamped. They include 23 low- and ultra-low-sulfur diesel
units (<50 ppm), as well as a number of cetane boosting units. Most
of those units are equipped with Equiow internals.
Continued
References: Getting Total Performance with Hydrotreating, Petroleum
Technology Quarterly, Spring 2002.
Premium Performance Hydrotreating with Axens HR 400 Series
Hydrotreating Catalysts, NPRA Annual Meeting, March 2002, San
Antonio.
The Hydrotreating Toolbox Approach, Harts European Fuel News,
May 29, 2002.
Squeezing the most from hydrotreaters, Hydrocarbon Asia, April/
May 2004.
Licensor: Axens.
Hydrotreating, diesel, continued
Hydrotreatinglube and wax
Application: The IsoTherming process provides reners with a cost-
effective approach to lube and wax hydrotreating to produce high-qual-
ity lube-base stocks and food-grade waxes.
Products: High-quality lube oils, food- or pharmaceutical-grade oil and
wax products.
Description: This process uses a novel approach to introduce hydro-
gen into the reactor; it enables much higher LHSV than conventional
hydrotreating reactors. The IsoTherming process removes the hydro-
gen mass transfer limitation and operates in a kinetically limited mode
since hydrogen is delivered to the reactor in the liquid phase as soluble
hydrogen.
The technology can be installed as a simple pre-treat unit ahead of
an existing hydrotreater reactor or a new stand-alone process unit. Fresh
feed, after heat exchange, is combined with hydrogen in Reactor One
mixer (1). The liquid feed with soluble hydrogen is fed to IsoTherming
Reactor One (2) where partial desulfurization, denitrocation and satu-
ration occurs.
The stream is combined with additional hydrogen in Reactor
Two mixer (3), and fed to IsoTherming Reactor Two (4) where further
desulfurization, denitrocation and saturation take place. Treated oil is
recycled (5) to the inlet of Reactor One. This recycle stream delivers more
hydrogen to the reactors and also acts as a heat sink; thus, a nearly iso-
thermal reactor operation is achieved.
Economics: Investment (basis 5,000 bpd)
Lube-base oil grassroots $7.5 million
Lube-base oil retrot $3.1 million
Parafn wax grassroots $6.0 million
Micro-wax grassroots $13.0 million
White oil $10.7 million

HydrotreatingRDS/VRDS/UFR/OCR
Application: Hydrotreat atmospheric and vacuum residuum feedstocks
to reduce sulfur, metals, nitrogen, carbon residue and asphaltene con-
tents. The process converts residuum into lighter products while im-
proving the quality of unconverted bottoms for more economic down-
stream use.
Products: Residuum FCC feedstock, coker feedstock, SDA feedstock or
low-sulfur fuel oil. VGO product, if separated, is suitable for further up-
grading by FCC units or hydrocrackers for gasoline/mid-distillate manu-
facture. Mid-distillate material can be directly blended into low-sulfur
diesel or further hydrotreated into ultra-low-sulfur diesel (ULSD).
The process integrates well with residuum FCC units to minimize
catalyst consumption, improve yields and reduce sulfur content of FCC
products. RDS/VRDS also can be used to substantially improve the yields
of downstream cokers and SDA units.
Description: Oil feed and hydrogen are charged to the reactors in a
once-through operation. The catalyst combination can be varied signi-
cantly according to feedstock properties to meet the required product
qualities. Product separation is done by the hot separator, cold separator
and fractionator. Recycle hydrogen passes through an H
2
S absorber.
A wide range of AR, VR and DAO feedstocks can be processed. Ex-
isting units have processed feedstocks with viscosities as high as 6,000
cSt at 100C and feed-metals contents of 500 ppm.
Onstream Catalyst Replacement (OCR) reactor technology has been
commercialized to improve catalyst utilization and increase run length
with high-metals, heavy feedstocks. This technology allows spent cata-
lyst to be removed from one or more reactors and replaced with fresh
while the reactors continue to operate normally. The novel use of up-
ow reactors in OCR provides greatly increased tolerance of feed solids
while maintaining low-pressure drop.
A related technology called UFR (upow reactor) uses a multibed
upow reactor for minimum pressure drop in cases where onstream
catalyst replacement is not necessary. OCR and UFR are particularly well
suited to revamp existing RDS/VRDS units for additional throughput or
heavier feedstock.
Installation: Over 20 RDS/VRDS units are in operation. Six units have
extensive experience with VR feedstocks. Twelve units prepare feedstock
for RFCC units. Three OCR units and one UFR unit are in operation, with
another two in engineering. Total current operating capacity is about
900,000 bpsd
References: Reynolds, Resid Hydroprocessing With Chevron Technol-
ogy, JPI, Tokyo, Japan, Fall 1998.
Reynolds and Brossard, RDS/VRDS Hydrotreating Broadens Appli-
cation of RFCC, HTI Quarterly, Winter 1995/96.

Hydrotreatingresid
Application: Upgrade or convert atmospheric and vacuum residues us-
ing the Hyvahl xed-bed process.
Products: Low-sulfur fuels (0.3% to 1.0% sulfur) and RFCC feeds (re-
moval of metals, sulfur and nitrogen, reduction of carbon residue). Thirty
percent to 50% conversion of the 565C
+
fraction into distillates.
Description: Residue feed and hydrogen, heated in a feed/efuent ex-
changer and furnace, enter a reactor sectiontypically comprising of a
guard-reactor section, main HDM and HDS reactors.
The guard reactors are onstream at the same time in series, and they
protect downstream reactors by removing or converting sediment, met-
als and asphaltenes. For heavy feeds, they are permutable in operation
(PRS technology) and allow catalyst reloading during the run. Permuta-
tion frequency is adjusted according to feed-metals content and process
objectives. Regular catalyst changeout allows a high and constant pro-
tection of downstream reactors.
Following the guard reactors, the HDM section carries out the re-
maining demetallization and conversion functions. With most of the
contaminants removed, the residue is sent to the HDS section where the
sulfur level is reduced to the design specication.
The PRS technology associated with the high stability of the HDS
catalytic system leads to cycle runs exceeding a year even when process-
ing VR-type feeds to produce ultra-low-sulfur fuel oil.
Yields: Typical HDS and HDM rates are above 90%. Net production of
12% to 25% of diesel + naphtha.
Economics:
Investments (Basis: 40,000 bpsd, AR to VR feeds,
2002 Gulf coast), US$/ bpsd 3,5005,500
Utilities, per bbl feed:
Fuel, equiv. fuel oil, kg 0.3
Power, kWhr 10
Steam production, MP, kg 25
Steam consumption, HP, kg 10
Water, cooling, m
3
1.1
Installation: Three units are in operation (one on atmospheric-residue
feed, the other two on vacuum residue). The total installed capacity will
reach 134,000 bpsd.
References: Option for Resid Conversion, BBTC, Oct. 89, 2002, Istanbul.
Maintaining on-spec products with residue hydroprocessing,
2000 NPRA Annual Meeting, March 2628, 2000, San Antonio.
Licensor: Axens.
Isomerization
Application: C
5
/C
6
parafn-rich hydrocarbon streams are isomerized to
produce high RON and MON product suitable for addition to the gaso-
line pool.
Description: Several variations of the C
5
/ C
6
isomerization process are
available. With either a zeolite or chlorinated alumina catalyst, the choice
can be a once-through reaction for an inexpensive-but-limited octane
boost, or, for substantial octane improvement and as an alternate (in ad-
dition) to the conventional DIH recycle option, the Ipsorb Isom scheme
shown to recycle the normal parafns for their complete conversion.
The Hexorb Isom conguration achieves a complete normal parafn con-
version plus substantial conversion of low (75) octane methyl pentanes
gives the maximum octane results. With the most active isomerization
catalyst (chlorinated Alumina catalyst), particularly with the Akzo Nobel /
Axens jointly developed ATIS2L catalyst, the isomerization performance
varies from 84 to 92: once-through isomerization -84, isomerization
with DIH recycle -88, Ipsorb -90, Hexorb-92.
Operating conditions: The Ipsorb Isom process uses a deisopentanizer
(1) to separate the isopentane from the reactor feed. A small amount of
hydrogen is also added to reactor (2) feed. The isomerization reaction
proceeds at moderate temperature producing an equilibrium mixture of
normal and isoparafns. The catalyst has a long service life. The reactor
products are separated into isomerate product and normal parafns in
the Ipsorb molecular sieve separation section (3) which features a novel
vapor phase PSA technique. This enables the product to consist entirely
of branched isomers.
Economics: (Basis: Ipsorb A Isomerization unit with a 5,000-bpsd 70
RONC feed needing a 20-point octane boost):
Investment*, million US$ 13
Utilities:
Steam, HP, tph 1.0
Steam, MP, tph 8.5
Steam, LP, tph 6.8
Power, kWh /h 310
Cooling water, m
3
/ h 100
* Mid-2002, Gulf coast, excluding cost of noble metals
Installation: Of 30 licenses issued for C
5
/ C
6
isomerization plants, 12
units are operating including one Ipsorb unit.
Reference: Axens/Akzo Nobel, Advance solutions for parafn isomeri-
zation, NPRA Annual Meeting, March 2004, San Antonio.
Licensor: Axens.
Isomerization
Application: Convert normal olens to isoolens.
Description:
C
4
olefin skeletal isomerization (IsomPlus)
A zeolite-based catalyst especially developed for this process pro-
vides near equilibrium conversion of normal butenes to isobutylene at
high selectivity and long process cycle times. A simple process scheme
and moderate process conditions result in low capital and operating
costs. Hydrocarbon feed containing n-butenes, such as C
4
rafnate, can
be processed without steam or other diluents, nor the addition of cata-
lyst activation agents to promote the reaction. Near-equilibrium con-
version levels up to 44% of the contained n-butenes are achieved at
greater than 90% selectivity to isobutylene. During the process cycle,
coke gradually builds up on the catalyst, reducing the isomerization ac-
tivity. At the end of the process cycle, the feed is switched to a fresh
catalyst bed, and the spent catalyst bed is regenerated by oxidizing the
coke with an air/nitrogen mixture. The butene isomerate is suitable for
making high purity isobutylene product.
C
5
olefin skeletal isomerization (IsomPlus)
A zeolite-based catalyst especially developed for this process pro-
vides near-equilibrium conversion of normal pentenes to isoamylene at
high selectivity and long process cycle times. Hydrocarbon feeds con-
taining n-pentenes, such as C
5
rafnate, are processed in the skeletal
isomerization reactor without steam or other diluents, nor the addition
of catalyst activation agents to promote the reaction. Near-equilibrium
conversion levels up to 72% of the contained normal pentenes are ob-
served at greater than 95% selectivity to isoamylenes.
Economics: The ISOMPLUS process offers the advantages of low capital
investment and operating costs coupled with a high yield of isobutylene.
Also, the small quantity of heavy byproducts formed can easily be blend-
ed into the gasoline pool. Capital costs (equipment, labor and detailed
engineering) for three different plant sizes are:
Total installed cost: Feedrate, Mbpd ISBL cost, $MM
10 8
15 11
30 30
Utility costs: per barrel of feed (assuming an electric-motor-driven
compressor) are:
Power, kWh 3.2
Fuel gas, MMBtu 0.44
Steam, MP, MMBtu 0.002
Water, cooling, MMBtu 0.051
Nitrogen, scf 57250
Continued
Installation: Two plants are in operation. Two licensed units are in vari-
ous stages of design.
Licensor: CDTECH and Lyondell Chemical Co.
Isomerization, continued
Isomerization
Application: Hydrisom is ConocoPhillips selective diolen hydrogena-
tion process, with specic isomerization of butene-1 to butene-2 and
3-methyl-butene-1 to 2-methyl-butene-1 and 2-methyl-butene-2. The
Hydrisom process uses a liquid-phase reaction over a commercially avail-
able catalyst in a xed-bed reactor.
Description: ConocoPhillips Hydrisom Process is a once-through reac-
tion and, for typical cat cracker streams, requires no recycle or cooling.
Hydrogen is added downstream of the olen feed pump on ratio control
and the feed mixture is preheated by exchange with the fractionator
bottoms and/or low-pressure steam. The feed then ows downward
over a xed bed of commercial catalyst.
The reaction is liquid-phase, at a pressure just above the bubble
point of the hydrocarbon/hydrogen mixture. The rise in reactor tem-
perature is a function of the quantity of butadiene in the feed and the
amount of butene saturation that occurs.
The Hydrisom process can also be congured using a proprietary
catalyst to upgrade streams containing diolens up to 50% or more,
e.g., steam cracker C
4
steams, producing olen-rich streams for use as
chemical, etherication and/or alkylation feedstocks.
Installation of a Hydrisom unit upstream of an etherication and/
or alkylation unit can result in a very quick payout of the investment
due to:
Improved etherication unit operations
Increased ether production
Increased alkylate octane number
Increased alkylate yield
Reduced chemical and HF acid costs
Reduced ASO handling
Reduced alkylation unit utilities
Upgraded steam cracker or other high diolen streams (30% to
50%) for further processing.
Installation: Ten units licensed worldwide, including an installation at
ConocoPhillips Sweeny, Texas, Renery.
Isomerization
Application: The widely used Butamer process is a high-efciency, cost
effective means of meeting the demands for the production of isobu-
tane by isomerizing normal butane (nC
4
) to isobutane (i C
4
).
Motor-fuel alkylate is one blending component that has seen a sub-
stantial increase in demand because of its parafnic, high-octane, low-
vapor pressure blending properties. Isobutane is a primary feedstock for
producing motor-fuel alkylate.
Description: UOPs innovative hydrogen-once-through (HOT) Butamer
process results in substantial savings in capital equipment and utility
costs by eliminating the need for a product separator or recycle-gas
compressor.
Typically, two reactors, in series ow, are used to achieve high
onstream efciency. The catalyst can be replaced in one reactor while
operation continues in the other. The stabilizer separates the light gas
from the reactor efuent.
A Butamer unit can be integrated with an alkylation unit. In this
application, the Butamer unit feed is a side-cut from an isostripper col-
umn, and the stabilized isomerate is returned to the isostripper column.
Unconverted n-butane is recycled to the Butamer unit, along with n-bu-
tane from the fresh feed. Virtually complete conversion of n-butane to
isobutane can be achieved.
Feed: The best feeds for a Butamer unit contain the highest practical
n-butane content, and only small amounts of isobutane, pentanes and
heavier material. Natural gas liquids (NGL) from a UOP NGL recovery unit
can be processed in a Butamer unit.
Yield: The stabilized isomerate is a near-equilibrium mixture of isobutane
and n-butane with small amounts of heavier material. The light-ends
yield from cracking is less than 1 wt-% of the butane feed.
Installation: More than 70 Butamer units have been commissioned, and
additional units are in design or construction. Butamer unit feed capaci-
ties range from 800 to 35,000+ bpsd (74 to 3,250 tpd).
Licensor: UOP LLC.
Isomerization
Application: The Par-Isom process is an innovative application using
high-performance nonchlorided-alumina catalysts for light-naphtha
isomerization. The process uses PI-242 catalyst, which approaches the
activity of chlorided alumina catalysts without requiring organic chloride
injection. The catalyst is regenerable and is sulfur and water tolerant.
Description: The fresh C
5
/ C
6
feed is combined with make-up and re-
cycle hydrogen which is directed to a charge heater, where the reactants
are heated to reaction temperature. The heated combined feed is then
sent to the reactor. Either one or two reactors can be used in series, de-
pending on the specic application.
The reactor efuent is cooled and sent to a product separator where
the recycle hydrogen is separated from the other products. Recovered
recycle hydrogen is directed to the recycle compressor and back to the
reaction section. Liquid product is sent to a stabilizer column where light
ends and any dissolved hydrogen are removed. The stabilized isomerate
product can be sent directly to gasoline blending.
Feed: Typical feed sources for the Par-Isom process include hydrotreated
light straight-run naphtha, light natural gasoline or condensate and light
rafnate from benzene extraction units.
Water and oxygenates at concentrations of typical hydrotreated
naphtha are not detrimental, although free water in the feedstock must
be avoided. Sulfur suppresses activity, as expected, for any noble-metal
based catalyst. However, the suppression effect is fully reversible by sub-
sequent processing with clean feedstocks.
Yield: Typical product C
5
+ yields are 97 wt% of the fresh feed. The
product octane is 81 to 87, depending on the ow conguration and
feedstock qualities.
Installation: The rst commercial Par-Isom process unit was placed in
operation in 1996. There are currently 10 units in operation. The rst
commercial application of PI-242 catalyst was in 2003, and the unit has
demonstrated successful performance meeting all expectations.
Licensor: UOP LLC.
Isomerization
Application: Most of the implemented legislation requires limiting
benzene concentration in the gasoline pool. This has increased the
demand for high-performance C
5
and C
6
naphtha isomerization tech-
nology because of its ability to reduce the benzene concentration in
the gasoline pool while maintaining or increasing the pool octane. The
Penex process has served as the primary isomerization technology for
upgrading C
5
/ C
6
light straight-run naphtha.
Description: UOPs innovative hydrogen-once-through (HOT) Penex pro-
cess results in sustantial savings in capital equipment and utility costs by
eliminating the need for a product separator or recycle-gas compressor.
The Penex process is a xed-bed process that uses high-activity chlo-
ride-promoted catalysts to isomerize C
5
/ C
6
parafns to higher-octane-
branched components. The reaction conditions promote isomerization
and minimize hydrocracking.
Typically, two reactors, in series ow, are used to achieve high
onstream efciency. The catalyst can be replaced in one reactor while
operation continues in the other. The stabilizer separates light gas from
the reactor efuent.
Products: For typical C
5
/ C
6
feeds, equilibrium will limit the product to
83 to 86 RONC on a single hydrocarbon pass basis. To achieve higher
octane, UOP offers several schemes in which lower octane components
are separated from the reactor efuent and recycled back to the reac-
tors. These recycle modes of operation can lead to product octane as
high as 93 RONC, depending on feed quality.
Yields:
Penex process: Octane 86
Penex process/DIH: Octane 90
Penex process/Molex process: Octane 91
DIP/Penex process/DIH: Octane 93
Feed: Penex process can process feeds with high levels of C
6
cyclics and
C
7
components. In addition, feeds with substantial levels of benzene
can be processed without the need for a separate saturation section.
Installation: UOP is the leading world-wide provider of isomerization tech-
nology. More than 120 Penex units are in operation. Capacities range
from 1,000 bpsd to more than 25,000 bpsd of fresh feed capacity.
Licensor: UOP LLC.

Isooctane
Application: Conversion of isobutylene contained in mixed-C
4
feeds to
isooctane (2,2,4 tri-methyl pentane) to produce a high-quality gasoline
blendstock. The full range of MTBE plant feeds can be processedfrom
renery FCC, olen-plant rafnate and isobutane dehydrogenation pro-
cesses. The NExOCTANE process is specically developed to minimize
conversion costs of existing MTBE units and offers a cost-effective alter-
native to MTBE production.
Products: Isooctene and isooctane can be produced, depending on the
reners gasoline pool. Typical product properties are:
Isooctene Isooctane
RONC 101103 99100
MONC 8587 9699
Specic gravity 0.7010.704 0.7260.729
Vapor pressure, psia 1.8 1.8
T50, F 215 212
T90, F 250 246
ASTM EP, F 380390 370380
Description: In the NExOCTANE process, reuse of existing equipment
from the MTBE unit is maximized. The process consists of three sections.
First, isobutylene is dimerized to isooctene in the reaction section. The
dimerization reaction occurs in the liquid phase over a proprietary acidic
ion-exchange resin catalyst, and it uses simple liquid-phase xed-bed
reactors. The isooctene product is recovered in a distillation system that
generally can utilize the existing fractionation equipment. Recovered
isooctene product can be further hydrogenated to produce isooctane. A
highly efcient trickle-bed hydrogenation technology is offered with the
NExOCTANE process. This compact and cost-effective technology does
not require recirculation of hydrogen. In the renery, the NExOCTANE
process ts as a replacement to MTBE production, thus associated ren-
ery operations are mostly unaffected.
Economics:
Investment cost for revamps depend on the existing MTBE plant
design, capacity and feedstock composition. Typical utility requirements
per bbl product:
Water, cooling, ft
3
1.2
Installation: Process has been in commercial operation since 2002.
Licensor: Kellogg Brown & Root, Inc., and Fortum Oil and Gas OY.

Isooctane/isooctene
Application: CDIsoether is used for manufacture of high-octane, low-
vapor pressure, MTBE-free isooctene and/or isooctane for gasoline
blending. Coproduction of MTBE and isooctene/isooctane in the desired
ratio is also possible.
Feed: Hydrocarbon streams containing reactive tertiary olens such as:
FCC C
4
s, steamcracker C
4
s or isobutane dehydrogenation product.
Products: Isooctene or isooctane stream containing at least 85% of C
8
s,
with less than 5,000 ppm oligomers higher than C
12
s.
Description: Depending on conversion and investment requirements,
various options are available. CDIsoether can provide isobutylene con-
version of up to 99%. The C
4
feed is mixed with a recycle stream con-
taining oxygenates (such as TBA and MTBE), used as selectivator and
heated before entering the reactor. The reactor (1) is a water-cooled
tubular reactor (WCTR) or a boiling-point reactor (BPR).
The heat of reaction is removed by circulating water through the
shell of the WCTR, while the heat of reaction remains in the two-phase
BPR efuent. There is no product recycle. The reactor efuent ows,
along with the selectivator, to the reaction column (2), where isobutene
conversion is maximized using catalytic distillation and isooctene prod-
uct is fractionated as bottoms product.
Unreacted C
4
s are taken as column overhead and the selectivator is
drawn as a side stream for recycle together with some C
4
hydrocarbons.
The isooctene product can be sent to storage or fed to the hydrogena-
tion unit to produce saturated hydrocarbonisooctane.
Economics:
Investment (Basis grassroots CDIsoethers unit, charging FCC C
4
s)
US$5,0007,000 per bpsd of isooctene product
Investment for retrotting an existing MTBE unit to isooctene
production US$500 750 per bpsd of isooctene produced
Utilities, per bbl of isooctene:
Steam, (300 psig), lb 200250
Water, cooling, gal 1,5002,000
Power, kWh 1.62.0
Licensor: Snamprogetti SpA.

Isooctene/Isooctane/ETBE
Application: To produce isooctene or isooctane from isobutylene both
stepsvia catalytic dimerization followed by hydrogenation; with inter-
mediate and nal fractionation as required to meet nal product speci-
cations. Ideally, it is a drop-in to an existing MTBE reactor with pat-
ented use of modier to improve selectivity and prolong catalyst life.
The process can be easily modied to make ETBE from ethanol and
isobutylene as well.
Description: The process produces an isooctene intermediate or nal
product starting with either a mixed C
4
feed or on-purpose isobutylene
production. It is based on a highly selective conversion of isobutylene to
isooctene followed by hydrogenation, which will convert over 99.5%
of the isooctene to isooctane. The product has high-gasoline blending
quality with superior octane rating and low Rvp. The design has the
added advantage of being inter-convertible between isooctene/isooc-
tane and MTBE production.
Economics: The drop-in design capability offers an efcient and cost-
effective approach to conversion of existing MTBE units. In retro-t ap-
plications, this feature allows for maximum utilization of existing equip-
ment and hardware, thus reducing the capital costs of conversion to an
alternate process/production technology. For the production of isooc-
tane, the process uses low-risk conventional hydrogenation with slight
design enhancements for conversion of isooctene.
The unit can be designed to be inter-convertible between MTBE, iso-
octene/isooctane and/or ETBE operations. Thus, economics, as well as
changes in regulations, can dictate changes in the mode of operation
over time.
Commercial plants: Preliminary engineering and licensing is under eval-
uation at several MTBE producers worldwide.
Licensor: Lyondell Chemical and Aker Kvaerner.

LPG recovery
Application: Recovery of propane and heavier components from various
renery offgas streams and from low-pressure associated natural gas.
Propane recovery levels approaching 100% are typical.
Description: Low-pressure hydrocarbon gas is compressed and dried be-
fore being chilled by cross-exchange and propane refrigerant. The chilled
feed stream is then contacted with a recycled liquid ethane stream in the
propane absorber. The absorber bottoms is pumped to the deethanizer,
which operates at higher pressure than the absorber. The tower over-
head is condensed with propane refrigerant to form a reux stream
composed primarily of ethane. A slip stream of the reux is withdrawn
and recycled back to the propane absorber. The deethanizer bottoms
stream contains the valuable propane and heavier components which
may be further processed as required by conventional fractionation.
Economics: Compared to other popular LPG recovery processes, PRO-
MAX typically requires 1025% less refrigeration horsepower.
Installation: First unit under construction for Pertamina.
Reference: US Patent 6,405,561 issued June 18, 2002.
Licensor: Black & Veatch Pritchard, Inc.

Lube and wax processing
Application: Vacuum gas oils (VGOs) are simultaneously extracted and
dewaxed on a single unit to produce low-pour aromatic extracts and
lube-base stocks having low-pour points. Low viscosity grades (60 SUS)
to bright stocks can be produced. With additional stages of ltration,
waxes can be deoiled to produce fully rened parafn waxes.
Products: Lube-base stocks having low pour points ( 20C). Very low
pour point aromatic extracts. Slack waxes or low-oil content waxes.
Description: Process Dynamics integrated extraction/dewaxing technol-
ogy is a revolutionary process combining solvent extraction and solvent
dewaxing onto a single unit, using a common solvent system, for extrac-
tion and dewaxing steps. This process offers the advantage of operating
a single unit rather than separate extraction and dewaxing units; thus,
reducing both capitol and operating costs. The more selective solvent
system produces lube-base stocks of higher quality and higher yields
when compared to other technologies.
Primary solvent and warm feed are mixed together; temperature is
controlled by adding the cosolvent solvent. Filtrate or wax may be re-
cycled for solids adjustment. Cold cosolvent is added, and the slurry is
ltered (or separated by other means). Solvents are recovered from the
primary ltrate producing an aromatic extract. The wax cake is repulped
with additional solvent/cosolvent mix and reltered. Solvents are recov-
ered from the ltrate producing a lube-base stock.
Extraction/dewaxing comparisons of 90 SUS stock
Furfural/MEK Process Dynamics
A B
Rafnate yields, vol% 53 60 71
Dewaxed oil properties:
Viscosity @40C, cSt 16.5 18.7 20
Viscosity index 92 98 92
Pour pt., F 5 5 5
Installation: Basic engineering package for the rst commercial unit has
been completed.

Lube extraction
Application: Bechtels Furfural Rening process is a solvent-extraction
process that uses furfural as the solvent to selectively remove undesir-
able components of low lubrication oil quality, which are naturally pres-
ent in crude oil distillate and residual stocks. This process selectively re-
moves aromatics and compounds containing heteroatoms (e.g., oxygen,
nitrogen and sulfur). The unit produces parafnic rafnates suitable for
further processing into lube base stocks.
Products: A rafnate that may be dewaxed to produce a high-qual-
ity lube-base oil, characterized by high viscosity index, good thermal
and oxidation stability, light color and excellent additive response. The
byproduct extracts, being high in aromatic content, can be used, in
some cases, for carbon black feedstocks, rubber extender oils and other
nonlube applications where this feature is desirable.
Description: The distillate or residual feedstock and solvent are contact-
ed in the extraction tower (1) at controlled temperatures and owrates
required for optimum countercurrent, liquid-liquid extraction of the
feedstock. The extract stream, containing the bulk of the solvent, exits
the bottom of the extraction tower. It is routed to a recovery section to
remove solvent contained in this stream. Solvent is separated from the
extract oil by multiple-effect evaporation (2) at various pressures, fol-
lowed by vacuum ashing and steam stripping (3) under vacuum. The
rafnate stream exits the overhead of the extraction tower and is routed
to a recovery section to remove the furfural solvent contained in this
stream by ashing and steam stripping (4) under vacuum.
The solvent is cooled and recycled to the extraction section. Over-
head vapors from the steam strippers are condensed and combined with
the solvent condensate from the recovery sections and are distilled at
low pressure to remove water from the solvent. Furfural forms an azeo-
trope with water and requires two fractionators. One fractionator (5)
separates the furfural from the azeotrope, and the second (6) separates
water from the azeotrope. The water drains to the oily-water sewer. The
solvent is cooled and recycled to the extraction section.
Economics:
Investment (Basis: 10,000-bpsd feed rate capacity,
2004 US Gulf Coast), $/ bpsd 2,600
Fuel, 10
3
Btu (absorbed) 120
Electricity, kWh 2
Steam, lb 5
Installation: For almost 60 years, this process has been or is being used
in over 100 licensed units to produce high-quality lubricating oils.
Lube extraction
Application: Bechtels MP Rening process is a solvent-extraction pro-
cess that uses N-methyl-2-pyrrolidone (NMP) as the solvent to selec-
tively remove the undesirable components of low-quality lubrication oil,
which are naturally present in crude oil distillate and residual stocks.
The unit produces parafnic or naphthenic rafnates suitable for further
processing into lube-base stocks. This process selectively removes aro-
matics and compounds containing heteroatoms (e.g., oxygen, nitrogen
and sulfur).
Products: A rafnate that may be dewaxed to produce a high-qual-
ity lube-base oil, characterized by high viscosity index, good thermal
and oxidation stability, light color and excellent additive response. The
byproduct extracts, being high in aromatic content, can be used, in
some cases, for carbon black feedstocks, rubber extender oils and other
nonlube applications where this feature is desirable.
Description: The distillate or residual feedstock and solvent are contact-
ed in the extraction tower (1) at controlled temperatures and owrates
required for optimum countercurrent, liquid-liquid extraction of the
feedstock. The extract stream, containing the bulk of the solvent, exits
the bottom of the extraction tower. It is routed to a recovery section
to remove solvent contained in this stream. Solvent is separated from
the extract oil by multiple-effect evaporation (2) at various pressures,
followed by vacuum ashing and steam stripping (3) under vacuum.
The rafnate stream exits the overhead of the extraction tower and is
routed to a recovery section to remove the NMP solvent contained in
this stream by ashing and steam stripping (4) under vacuum.
Overhead vapors from the steam strippers are condensed and com-
bined with solvent condensate from the recovery sections and are dis-
tilled at low pressure to remove water from the solvent (5). Solvent is
recovered in a single tower because NMP does not form an azeotrope
with water, as does furfural. The water is drained to the oily-water sew-
er. The solvent is cooled and recycled to the extraction section.
Economics:
Fuel, 10
3
Btu (absorbed) 100
Electricity, kWh 2
Steam, lb 5
Installation: This process is being used in 15 licensed units to produce high-
quality lubricating oils. Of this number, eight are units converted from phe-
nol or furfural, with another three units being planned for conversion.
Continued
Lube hydrotreating
Application: The Bechtel Hy-Finishing process is a specialized hydrotreating
technology to remove impurities and improve the quality of parafnic
and naphthenic lubricating base oils. In the normal conguration, the
hydrogen nishing unit is located in the processing scheme between the
solvent extraction and solvent dewaxing units for a lube plant operating
on an approved lube crude. In this application, the unit operates under
mild hydrotreating conditions to improve color and stability, to reduce
sulfur, nitrogen, oxygen and aromatics, and to remove metals.
Another application is Hy-Starting, which is a more severe hydro-
treating process (higher pressure and lower space velocity) and upgrades
distillates from lower-quality crudes. This unit is usually placed before
solvent extraction in the processing sequence to upgrade distillate qual-
ity and, thus, improve extraction yields at the same rafnate quality.
Description: Hydrocarbon feed is mixed with hydrogen (recycle plus
makeup), preheated, and charged to a xed-bed hydrotreating reac-
tor (1). Reactor efuent is cooled in exchange with the mixed feed-hy-
drogen stream. Gas-liquid separation of the efuent occurs rst in the
hot separator (2) then in the cold separator (3). The hydrocarbon liquid
stream from each of the two separators is sent to the product stripper (4)
to remove the remaining gas and unstabilized distillate from the lube-oil
product. The product is then dried in a vacuum ash (5). Gas from the
cold separator is amine-scrubbed (6) to remove H
2
S before compression
in the recycle hydrogen compressor (7).
Economics:
Investment (Basis 7,000-bpsd feedrate capacity,
2004 US Gulf Coast), $/bpsd 4,200
Fuel, 10
3
Btu (absorbed) 20
Electricity, kWh 5
Steam, lb 15

Lube hydrotreating
Application: Hy-Raff is a new process to hydrotreat rafnates from an
extraction unit of a solvent-based lube oil plant for upgrading standard
Group I lube-base oils to produce Group II base oils. Sulfur is reduced to
below 0.03 wt% and saturates are increased to greater than 90 wt%.
The integration of this process into an existing base oil plant allows
the operator to cost-effectively upgrade base-oil products to the new
specications rather than scrapping the existing plant and building an
expensive new hydrocracker-based plant.
The product from the Hy-Raff unit is a lube-base oil of sufcient
quality to meet Group II specications. The color of the nished prod-
uct is signicantly improved over standard-base oils. Middle distillate
byproducts are of sufcient quality for blending into diesel.
Description: Rafnate feed is mixed with hydrogen (recycle plus make-
up), preheated, and charged to a xed-bed hydrotreating reactor (1).
The reactor efuent is cooled in exchange with the mixed feed-hydrogen
stream. Gas-liquid separation of the efuent occurs rst in the hot sepa-
rator (2) then in the cold separator (3). The hydrocarbon liquid stream
from each of the two separators is sent to the product stripper (4) to
remove the remaining gas and unstabilized distillate from the lube-oil
product, and product is dried in a vacuum ash (5). Gas from the cold
separator is amine-scrubbed (6) for removal of H
2
S before compression
in the recycle-hydrogen compressor (7).
Economics:
2004 U.S. Gulf Coast), $/bpsd 5,900
Utilitiies, typical per bbl feed:
Fuel, 10
3
Btu (absorbed) 70
Electricity, kWh 5
Steam, lb 15
Lube oil refining, spent

Application: The Revivoil process can be used to produce high yields of
premium quality lube bases from spent motor oils. Requiring neither
acid nor clay treatment steps, the process can eliminate environmental
and logistical problems of waste handling and disposal associated with
conventional re-rening schemes.
Description: Spent oil is distilled in an atmospheric ash distillation
column to remove water and gasoline and then sent to the Thermal
Deasphalting (TDA) vacuum column for recovery of gas oil overhead
and oil bases as side streams. The energy-efcient TDA column features
excellent performance with no plugging and no moving parts. Metals
and metalloids concentrate in the residue, which is sent to an optional
Selectopropane unit for brightstock and asphalt recovery. This scheme
is different from those for which the entire vacuum column feed goes
through a deasphalting step; Revivoils energy savings are signicant,
and the overall lube oil base recovery is maximized. The results are sub-
stantial improvements in selectivity, quality and yields.
The nal, but very important step for base oil quality is a specic
hydronishing process that reduces or removes remaining metals and
metalloids, Conradson Carbon, organic acids, and compounds contain-
ing chlorine, sulfur and nitrogen. Color, UV and thermal stability are
restored and polynuclear aromatics are reduced to values far below the
latest health thresholds. Viscosity index remains equal to or better than
the original feed. For metal removal (> 96%) and rening-purication
duty, the multicomponent catalyst system is the industrys best.
Product quality: The oil bases are premium products; all lube oil base
specications are met by Revivoil processing from Group 1 through
Group 2 of the API basestocks denitions. Besides, a diesel can be ob-
tained, in compliance with the EURO 5 requirements (low sulfur).
Health & safety and environment: The high-pressure process is in line
with future European specications concerning carcinogenic PNA com-
pounds in the nal product at a level inferior to 5 wppm (less than 1
wt% PCA - IP346 method).
Economics: The process can be installed stepwise or entirely. A simpler
scheme consists of the atmospheric ash, TDA and hydronishing unit
and enables 70 80% recovery of lube oil bases. The Selectopropane
unit can be added at a later stage, to bring the oil recovery to the 95%
level on dry basis. Economics below show that for two plants of equal
capacity, payout times before taxes are two years in both cases.
Investment: Basis 100,000 metric tpy, water-free, ISBL 2004 Gulf
Coast, million US$
Configuration 1 (Atm. ash, TDA and Hydronishing units) 30
Configuration 2 (Same as above + Selectopropane unit) 35

Continued
Utilities: Basis one metric ton of water-free feedstock
Config. 1 Config. 2
Electrical power, kWh 45 55
Fuel, million kcal 0.62 0.72
Steam, LP, kg 23.2
Steam, MP, kg 872 890
Water, cooling, m
3
54 59
Installation: Ten units have been licensed using all or part of the Revivoil
Technology.
Licensor: Viscolube SpA and Axens.
Lube oil refining, spent, continued
Lube treating
Application: Lube rafnates from extraction are dewaxed to provide base-
stocks having low pour points (as low as 35C). Basestocks range from
light stocks (60N) to higher viscosity grades (600N and bright stock).
Byproduct waxes can also be upgraded for use in food applications.
Feeds: DILCHILL dewaxing can be used for a wide range of stocks that boil
above 550F, from 60N up through bright stock. In addition to rafnates
from extraction, DILCHILL dewaxing can be applied to hydrocracked stocks
and to other stocks from rafnate hydroconversion processes.
Processes: Lube basestocks have low pour points. Although slack wax-
es containing 210 wt% residual oil are the typical byproducts, lower-
oil-content waxes can be produced by using additional dewaxing and/or
warm-up deoiling stages.
Description: DILCHILL is a novel dewaxing technology in which wax crystals
are formed by cooling waxy oil stocks, which have been diluted with ketone
solvents, in a proprietary crystallizer tower that has a number of mixing
stages. This nucleation environment provides crystals that lter more quickly
and retain less oil. This technology has the following advantages over con-
ventional incremental dilution dewaxing in scraped-surface exchangers: less
lter area is required, less washing of the lter cake to achieve the same
oil-in-wax content is required, refrigeration duty is lower, and only scraped
surface chillers are required which means that unit maintenance costs are
lower. No wax recrystallization is required for deoiling.
Warm waxy feed is cooled in a prechiller before it enters the DILCHILL
crystallizer tower. Chilled solvent is then added in the crystallizer tower
under highly agitated conditions. Most of the crystallization occurs in
the crystallizer tower. The slurry of wax/oil/ketone is further cooled in
scraped-surface chillers and the slurry is then ltered in rotary vacuum
lters. Flashing and stripping of products recover solvent. Additional l-
tration stages can be added to recover additional oil or/to produce low-
oil content saleable waxes.
Economics: Depend on the slate of stocks to be dewaxed, the pour
point targets and the required oil-in-wax content.
Utilities: Depend on the slate of stocks to be dewaxed, the pour point
targets and the required oil-in-wax content.
Installation: The rst application of DILCHILL dewaxing was the conver-
sion of an ExxonMobil afliate unit on the U.S. Gulf Coast in 1972. Since
that time, 10 other applications have been constructed. These applica-
tions include both grassroots units and conversions of incremental dilu-
tion plants. Six applications use warm-up deoiling.

Lube treating
Application: Process to produce lube oil rafnates with high viscosity
index from vacuum distillates and deasphalted oil.
Feeds: Vacuum distillate lube cuts and deasphalted oils.
Products: Lube oil rafnates of high viscosity indices. The rafnates con-
tain substantially all of the desirable lubricating oil components present
in the feedstock. The extract contains a concentrate of aromatics that
may be utilized as rubber oil or cracker feed.
Description: This liquid-liquid extraction process uses furfural as the se-
lective solvent to remove aromatics and other impurities present in the
distillates and deasphalted oils. Furfural has a high solvent power for
those components that are unstable to oxygen as well as for other un-
desirable materials including color bodies, resins, carbon-forming con-
stituents and sulfur compounds. In the extraction tower, the feed oil is
introduced below the top at a predetermined temperature. The rafnate
phase leaves at the top of the tower, and the extract, which contains the
bulk of the furfural, is withdrawn from the bottom. The extract phase
is cooled and a so-called pseudo rafnate may be sent back to the
extraction tower. Multi-stage solvent recovery systems for rafnate and
extract solutions secure energy efcient operation.
3
of feed:
Electricity, kWh 10
Steam, MP, kg 10
Steam, LP, kg 35
Fuel oil, kg 20
Water, cooling, m
3
20
etary technology are in operation worldwide. The most recent is a com-
plete lube-oil production facility licensed to the state of Turkmenistan.
Mercaptan removal
Application: Extraction of mercaptans from gases, LPG, lower boiling
fractions and gasolines, or sweetening of gasoline, jet fuel and diesel by
in situ conversion of mercaptans into disuldes.
Products: Essentially mercaptan sulfur-free, i.e., less than 5 ppmw, and
concomitant reduced total sulfur content when treated by Merox ex-
traction technique.
Description: Merox units are designed in several ow congurations,
depending on feedstock type and processing objectives. All are charac-
terized by low capital and operating costs, ease of operation and mini-
mal operator attention.
Extraction: Gases, LPG and light naphtha are countercurrently extracted
(1) with caustic containing Merox catalyst. Mercaptans in the rich caustic
are oxidized (2) with air to disuldes that are decanted (3) before the
regenerated caustic is recycled.
Sweetening: Minalk is now the most prevalent Merox gasoline sweeten-
ing scheme. Conversion of mercaptans into disuldes is accomplished
with a xed bed of Merox catalyst that uses air and a continuous injec-
tion of only minute amounts of alkali. Sweetened gasoline from the
reactor typically contains less than one ppm sodium.
Heavy gasoline, condensate, kerosine/jet fuel and diesel can be
sweetened in a xed-bed unit that closely resembles Minalk, except that
a larger amount of more concentrated caustic is recirculated intermit-
tently over the catalyst bed. A new additive, Merox Plus catalyst activa-
tor, can be used to greatly extend catalyst life.
Economics: Typical capital investment and operating costs of some
Merox process schemes are given based on 2004 dollars for a 10,000-
bpsd capacity liquid unit and 10 million-scfd gas unit with modular de-
sign and construction.

Heavy
naphtha
Product Gas LPG Gasoline fixed bed
Scheme Ext. Ext. Minalk
Est. plant capital, modular $10
3
2,600 2,000 1,100 1,500
Direct operating cost, /bbl
(/10
6
scf) (1.5) 0.4 0.2 1.0
Installations: Capacity installed and under construction exceeds 13 million
bpsd. More than 1,600 units have been commissioned to date, with capaci-
ties between 40 and 140,000 bpsd. UOP has licensed gas Merox extraction
units with capacities as high as 2.9-billion-scfd for mercaptan control.
Licensor: UOP LLC.

NO
x
abatement
Application: Flue gases are treated with ammonia via ExxonMobils pro-
prietary selective noncatalytic NO
x
reduction technologyTHERMAL
DeNO
x
. NO
x
plus ammonia (NH
3
) are converted to elemental nitrogen
and water if temperature and residence time are appropriate. The tech-
nology has been widely applied since it was rst commercialized in
1974.
Products: If conditions are appropriate, the ue gas is treated to achieve
NO
x
reductions of 40% to 70%+ with minimal NH
3
slip or leakage.
Description: The technology involves the gas-phase reaction of NO with
NH
3
(either aqueous or anhydrous) to produce elemental nitrogen if con-
ditions are favorable. Ammonia is injected into the ue gas using steam
or air as a carrier gas into a zone where the temperature is 1,600F
to 2,000F. This range can be extended down to 1,300F with a small
amount of hydrogen added to the injected gas. For most applications,
wall injectors are used for simplicity of operation.
Yield: Cleaned ue gas with 40% to 70%+ NO
x
reduction and less than
10-ppm NH
3
slip.
Economics: Considerably less costly than catalytic systems but relatively
variable depending on scale and site specics. Third-party studies have
estimated the all-in cost at about 600 US$ / ton of NO
x
removed.
Installation: Over 135 applications on all types of red heaters, boilers
and incinerators with a wide variety of fuels (gas, oil, coal, coke, wood
and waste). The technology can also be applied to full-burn FCCU re-
generators.
Reference: McIntyre, A. D., Applications of the THERMAL DeNO
x
pro-
cess to utility and independent power production boilers, ASME Joint
International Power Generation Conference, Phoenix, 1994.
McIntyre, A. D., The THERMAL DeNO
x
process: Liquid fuels appli-
cations, International Flame Research Foundations 11th Topic Oriented
Technical Meeting, Biarritz, France, 1995.
McIntyre, A. D., Applications of the THERMAL DeNO
x
process to
FBC boilers, CIBO 13th Annual Fluidized Bed Conference, Lake Charles,
Louisiana, 1997.
Licensor: ExxonMobil Research and Engineering Co., via an alliance with
Engineers India Ltd. (for India) and Hamon Research-Cottrell (for the rest
of the world).

NO
x
reduction, low-temperature
Application: The LoTOx low-temperature oxidation process removes NO
x
from ue gases in conjunction with BELCOs EDV wet scrubbing system.
Ozone is a very selective oxidizing agent; it converts relatively insoluble
NO and NO
2
to higher, more soluble nitrogen oxides. These oxides are
easily captured in a wet scrubber that is controlling sulfur compounds
and/or particulates simultaneously.
Description: In the LoTO
x
process, ozone is added to oxidize insoluble
NO and NO
2
to highly oxidized, highly soluble species of NO
x
that can
be effectively removed by a variety of wet or semi-dry scrubbers. Ozone,
a highly effective oxidizing agent, is produced onsite and on demand
by passing oxygen through an ozone generatoran electric corona de-
vice with no moving parts. The rapid reaction rate of ozone with NO
x
results in high selectivity for NO
x
over other components within the gas
stream.
Thus, the NO
x
in the gas phase is converted to soluble ionic com-
pounds in the aqueous phase; the reaction is driven to completion, thus
removing NO
x
with no secondary gaseous pollutants. The ozone is con-
sumed by the process or destroyed within the system scrubber. All sys-
tem components are proven, well-understood technologies with a his-
tory of safe and reliable performance.
Operating conditions: Ozone injection typically occurs in the ue-gas
stream upstream of the scrubber, near atmospheric pressure and at
temperatures up to roughly 150C. For higher-temperature streams, the
ozone is injected after a quench section of the scrubber, at adiabatic
saturation, typically 60C to 75C. High-particulate saturated gas and
sulfur loading (SO
x
or TRS) do not cause problems.
Economics: The costs for NO
x
control using this technology are espe-
cially low when used as a part of a multi-pollutant control scenario.
Sulfurous and particulate-laden streams can be treated attractively as no
pretreatment is required by the LoTOx system.
Installation: The technology has been developed and commercial-
ized over the past seven years, winning the prestigious 2001 Kirkpat-
rick Chemical Engineering Technology Award. As of early 2002, four
full-scale commercial installations are operating successfully. Pilot-scale
demonstrations have been completed on coal- and petroleum-coke red
boilers, as well as renery FCC units.
Reference: Confuorto, et al., LoTO
x
technology demonstration at Mar-
athon Ashland Petroleum LLCs renery at Texas City, Texas, NPRA An-
nual Meeting, March 2004, San Antonio.
Licensor: Belco Technologies Corp., as a sub-licensor for The BOC
Group, Inc.

Olefin recovery
Application: Recovery of olens from renery and/or petrochemical
offgas streams that may otherwise be burned as fuel or ared.
Description: Well-proven low-temperature technology that achieves
high olen recoveries, often with minimal power consumption or rotat-
ing equipment.
The process owsheet can be optimized based on feed and product
pressures and the value of recovered olens. All necessary refrigeration
may be produced by turbo-expansion of feed gases to a low-pressure
fuel gas header. Plate-n heat exchangers are used to give high-energy
efciency and to maximize olen recovery.
Reux heat exchanger technology is used for very high olen recov-
ery, whereby a plate-n heat exchanger separates the desired olens in
a similar way to an absorption column.
Olen recovery units are normally supplied as a number of pre-as-
sembled modules for ease of installation and commissioning.
Economics: Olen recoveries in excess of 98% can be economically
achieved yielding payback times of typically less than 30 months.
Installation: Costain Oil, Gas & Process Ltd. has supplied approximately
15 units for recovery of propylene and butylenes from renery offgases
and dehydrogenation plant efuent, with numerous further installations
for recovery of ethylene, LPG and hydrogen.
Reference: Johnson, G. L., et al., Low temperature separation of hy-
drocarbon gas, US patent no. 6581410.
Tomlinson, T. R., Improved operating margins with ethylene recov-
ery, Petroleum Technology Quarterly, Spring 2002, p. 125.
Licensor: Costain Oil, Gas & Process Ltd.

Olefins recovery
Application: Recover high-purity hydrogen (H
2
) and C
2
+
liquid products
from renery offgases using cryogenics.
Description: Cryogenic separation of renery offgases and purges con-
taining 1080% H
2
and 15 40% hydrocarbon liquids such as ethylene,
ethane, propylene, propane and butanes. Renery offgases are option-
ally compressed and then pretreated (1) to remove sulfur, carbon di-
oxide ( CO
2
), H
2
O and other trace impurities. Treated feed is partially
condensed in an integrated multi-passage exchanger system (2) against
returning products and refrigerant.
Separated liquids are sent to a demethanizer (3) for stabilization while
hydrogen is concentrated (4) to 90 95%
+
purity by further cooling.
Methane, other impurities, and unrecovered products are sent to fuel or
optionally split into a synthetic natural gas (SNG) product and low-Btu
fuel. Refrigeration is provided by a closed-loop system (5). Mixed C
2
+
liq-
uids from the demethanizer can be further fractionated (6) into nished
petrochemical feeds and products such as ethane, ethylene, propane
and propylene.
Operating conditions: Feed capacities from 10 to 150+ million scfd. Feed
pressures as low as 150 psig. Ethylene recoveries are greater than 95%,
with higher recoveries of ethane and heavier components. Hydrogen
recoveries are better than 95% recovery.
Economics: Hydrogen is economically co-produced with liquid hydro-
carbon products, especially ethylene and propylene, whose high value
can subsidize the capital investment. High hydrocarbon liquid products
recovery is achieved without the cost for feed compression and subse-
quent feed expansion to fuel pressure. Power consumption is a function
of hydrocarbon quantities in the feed and feed pressure. High-purity
hydrogen is produced without the investment for a back-end PSA
system. Project costs can have less than a two-year simple payback.
Installations: Five operating renery offgas cryogenic systems processing
FCC offgas, cat reformer offgas, hydrotreater purge gas, coker offgas
and renery fuel gas. Several process and refrigeration schemes used
since 1987 with the most recent plant startup in 2001.
Reference: US Patents 6,266,977 and 6,560,989.
Trautmann, S. R. and R. A. Davis, Renery offgasesalternative
sources for ethylene recovery and integration, AIChE Spring Meeting,
New Orleans, March 14, 2002, Paper 102d.
Licensor: Air Products and Chemicals Inc.

Olefins recovery
Application: Linde BOC Process Plants Cryo-Plus process recovers ethyl-
ene or propylene and heavier components from renery offgas streams.
Typical applications are on cat crackers, cokers or reformers downstream
of the existing gas-recovery systems. Incremental valuable hydrocarbons
that are currently being lost to the renery fuel system can now be eco-
nomically recovered.
Description: Renery offgases from cat crackers, cokers or other sources
are rst dehydrated by molecular sieve (1). The expander/compressor
(2a) compresses the gas stream, which is then cooled by heat exchange
with internal process streams (3). Depending on the richness of the feed
gas, supplemental refrigeration (4) may be used to further cool the gas
stream prior to primary vapor/liquid separation (5). Light gases are fed
to a turboexpander (2b) where the pressure is reduced resulting in a low
discharge temperature. The expander discharge is fed to the bottom of
the LEFC (6). The HEFC (7) overhead is cooled and fed to the top of the
LEFC. The recovered ethylene or propylene and heavier liquid stream exit
the bottom of the HEFC (7). Process advantages include:
Low capital cost
High propylene or high ethylene recovery (up to 99%)
Low energy usage
Small footprintcan be modularized
Simple to operate
Wide range of turndown capability.
Economics: Typically, the payback time for plant investment is one to
two years.
Installation: Sixteen plants operating in US reneries, with two under
construction. The rst plant was installed in 1984.
References: Buck, L., Separating hydrocarbon gases, US Patent No.
4,617,039, Oct. 14, 1986.
Key, R., and Z. Malik, Technology advances improve liquid recovery
from renery offgases, NPRA Annual Meeting, San Antonio, March
2628, 2000.
Licensor: Linde BOC Process Plants LLC, a member of Linde Engineering
Division.
Olefins-butenes extractive distillation

Application: Separation of pure C
4
olens from olenic/parafnic C
4
mix-
tures via extractive distillation using a selective solvent. BUTENEX is the
Uhde technology to separate light olens from various C
4
feedstocks,
which include ethylene cracker and FCC sources.
Description: In the extractive distillation (ED) process, a single-com-
pound solvent, N-Formylmorpholine (NFM), or NFM in a mixture with
further morpholine derivatives, alters the vapor pressure of the com-
ponents being separated. The vapor pressure of the olens is lowered
more than that of the less soluble parafns. Parafnic vapors leave the
top of the ED column, and solvent with olens leaves the bottom of the
ED column.
The bottom product of the ED column is fed to the stripper to
separate pure olens (mixtures) from the solvent. After intensive heat
exchange, the lean solvent is recycled to the ED column. The solvent,
which can be either NFM or a mixture including NFM, perfectly satises
the solvent properties needed for this process, including high selectivity,
thermal stability and a suitable boiling point.
Economics:
Consumption per metric ton of FCC C
4
fraction feedstock:
Steam, t / t 0.5 0.8
Water, cooling ( T = 10C ), m
3
/ t 15.0
Electric power, kWh/t 25.0
Product purity:
n - Butene content 99.
+
wt. % min.
Solvent content 1 wt. ppm max.
Installation: Two commercial plants for the recovery of n - butenes have
been installed since 1998.

Olefins-dehydrogenation
Application: The Uhde STeam Active Reforming STAR process produces
(a) propylene as feedstock for polypropylene, propylene oxide, cumene,
acrylonitrile or other propylene derivatives, and (b) butylenes as feed-
stock for methyl tertiary butyl ether (MTBE), alkylate, isooctane, polybu-
tylenes or other butylene derivatives.
Feed: Liqueed petroleum gas (LPG) from gas elds, gas condensate
elds and reneries.
Product: Propylene (polymer- or chemical-grade); isobutylene; n-butylenes;
high-purity hydrogen (H
2
) may also be produced as a byproduct.
Description: The fresh parafn feedstock is combined with parafn re-
cycle and internally generated steam. After preheating, the feed is sent
to the reaction section. This section consists of an externally red tubular
xed-bed reactor (Uhde reformer) connected in series with an adiabat-
ic xed-bed oxyreactor (secondary reformer type). In the reformer, the
endothermic dehydrogenation reaction takes place over a proprietary,
noble metal catalyst.
In the adiabatic oxyreactor, part of the hydrogen from the interme-
diate product leaving the reformer is selectively converted with added
oxygen or air, thereby forming steam. This is followed by further dehy-
drogenation over the same catalyst. Exothermic selective H
2
conversion
in the oxyreactor increases olen product space-time yield and supplies
heat for further endothermic dehydrogenation. The reaction takes place
at temperatures between 500C600C and at 4 bar6 bar.
The Uhde reformer is top-red and has a proprietary cold out-
let manifold system to enhance reliability. Heat recovery utilizes process
heat for high-pressure steam generation, feed preheat and for heat re-
quired in the fractionation section.
After cooling and condensate separation, the product is subse-
quently compressed, light-ends are separated and the olen product is
separated from unconverted parafns in the fractionation section.
Apart from light-ends, which are internally used as fuel gas, the
olen is the only product. High-purity H
2
may optionally be recoverd
from light-ends in the gas separation section.
Economics: Typical specic consumption gures (for polymer-grade
propylene production) are shown (per metric ton of propylene prod-
uct):
Propane, kg/metric ton 1,200
Fuel gas,GJ/metric ton 6.4
Circul. cooling water, m
3
/metric ton 220
Electrical energy, kWh/metric ton 180
Installations: Two commercial plants using the STAR process for dehy-

Continued
drogenation of isobutane to isobutylene have been commissioned (in
the US and Argentina). More than 60 Uhde reformers and 25 Uhde
secondary reformers have been constructed worldwide.
References: Heinritz-Adrian, M., N. Thiagarajan, S. Wenzel and H. Gehrke,
STARUhdes dehydrogenation technology (an alternative route to C
3
-
and C
4
-olens), ERTC Petrochemical 2003, Paris, France, March 2003.
Thiagarajan, N., U. Ranke and F. Ennenbach, Propane/butane de-
hydrogenation by steam active reforming, Achema 2000, Frankfurt,
Germany, May 2000.
Olefins-dehydrogenation, continued
3
C
4
cuts
Application: To dimerize light olens such as ethylene, propylene and
butylenes using the Dimersol process. The main applications are:
Dimerization of propylene, producing a high-octane, low-boiling
point gasoline called Dimate
Dimerization of n-butylene producing C
8
olens for plasticizer syn-
thesis.
The C
3
feeds are generally the propylene cuts from catalytic crack-
ing units. The C
4
cut source is mainly the rafnate from butadiene and
isobutylene extraction.
Description: Dimerization is achieved in the liquid phase at ambient
temperature by means of a soluble catalytic complex. One or several
reactors (1) in series are used. After elimination of catalyst (2, 3), the
products are separated in an appropriate distillation section (4).
Product quality: For gasoline production, typical properties of the Di-
mate are:
Specic gravity, @15C 0.70
End point, C 205
70% vaporized, C 80
Rvp, bar 0.5
RONC 96
MONC 81
RON blending value, avg. 103
Economics: For a plant charging 100,000 tpy of C
3
cut (% propylene)
and producing 71,000 tpy of Dimate gasoline:
Investment for a 2002 ISBL Gulf Coast erected cost,
excluding engineering fees, US $7 million
Utilities per ton of feed
Electric power, kWh 10.8
Steam, HP, t 0.14
Water, cooling, t 28.5
Catalyst + chemicals, US$ 9.3
Installation: Twenty-seven units have been built or are under construc-
tion.
Reference: Olen oligomerization with homogeneous catalysis, 1999
Dewitt Petrochemical Conference, Houston.
Licensor: Axens.

Application: To produce C
6
+ isoolen fractions that can be used as
high-octane blending stocks for the gasoline pool and high-smoke-
point blending stocks for kerosine and jet fuel. The Polynaphtha and
Selectopol processes achieve high conversions of light olenic fractions
into higher value gasoline and kerosine from propylene and mixed-bu-
tene fractions such as C
3
and C
4
cuts from cracking processes.
Description: Propylene or mixed butenes (or both) are oligomerized
catalytically in a series of xed-bed reactors (1). Conversion and selectiv-
ity are controlled by reactor temperature adjustment while the heat of
reaction is removed by intercooling (2). The reactor section efuent is
fractionated (3), producing rafnate, gasoline and kerosine.
The Selectopol process is a variant of the polynaphtha process where
the operating conditions are adjusted to convert selectively the isobu-
tene portion of an olenic C
4
fraction to high-octane, low-Rvp gasoline
blending stock. It provides a low-cost means of debottlenecking existing
alkylation units by converting all of the isobutene and a small percent-
age of the n-butenes, without additional isobutane.
Polynaphtha and Selectopol processes have the following features:
low investment, regenerable solid catalyst, no catalyst disposal problems,
long catalyst life, mild operating conditions, versatile product range,
good-quality motor fuels and kerosine following a simple hydrogenation
step and the possibility of retrotting old phosphoric acid units.
The polygasoline RON and MON obtained from FCC C
4
cuts are sig-
nicantly higher than those of FCC gasoline and, in addition, are sulfur-
free. Hydrogenation improves the MON, whereas the RON remains high
and close to that of C
4
alkylate.
Kerosine product characteristics such as oxidation stability, freezing
point and smoke point are excellent after hydrogenation of the polynaph-
tha product. The kerosine is also sulfur-free and low in aromatics.
The Polynaphtha process has operating conditions very close to those
of phosphoric acid poly units. Therefore, an existing units major equip-
ment items can be retained with only minor changes to piping and instru-
mentation. Some pretreatment may be needed if sulfur, nitrogen or water
contents in the feed warrant; however, the equipment cost is low.
Economics: Typical ISBL Gulf Coast investments for 5,000-bpd of FCC
C
4
cut for polynaphtha (of maximum exibility) and Selectopol (for maxi-
mum gasoline) units are US$8.5 million and US$3.0 million, respectively.
Respective utility costs are US$4.4 and US$1.8 per ton of feed while
catalyst costs are US$0.2 per ton of feed for both processes.
Installations: Seven Selectopol and polynaphtha units have been licensed (ve
in operation), with a cumulative operating experience exceeding 40 years.
Licensor: Axens.

Oxygen enrichment for Claus units
Application: Increase the capacity of Claus plants and decompose haz-
ardous materials such as ammonia
Description: As clean fuels regulations become effective, reners
must recover more sulfur in their Claus plants. As a byproduct of deep
desulfurization, ammonia is generated and typically must be decom-
posed in the Claus plant. To upgrade the sulfur recovery units (SRUs)
accordingly, oxygen enrichment is an efcient and low-cost option. Oxy-
gen enrichment can increase sulfur capacity substantially and is capable
of decomposing ammonia from sour-water stripper gas very efciently.
Oxygen addition can be done in three levels, depending on the re-
quired capacity increase:
1. Up to approximately 28% oxygen. Oxygen is simply added to the
Claus furnace air. This can raise sulfur capacity up to 30%.
2. Up to approximately 40% oxygen. The burner of the Claus fur-
nace must be replaced. Up to 50% additional sulfur capacity can be
achieved by this method.
3. Beyond 40% oxygen. The temperature in the Claus furnace is ele-
vated so high that the product gas must be recycled to maintain temper-
ature control. This process is expensive and, therefore, rarely applied.
Oxygen sources can be liquid oxygen tanks, onsite ASUs or pipeline
supply. Oxygen consumption in Claus plants uctuates widely in most
cases; thus, tanks are the best choice due to ease of operation, exibility
and economy. For oxygen addition into the CS air duct, a number of
safety rules must be observed. The oxygen metering device FLOWTRAIN
contains all of the necessary safety features, including ow control, low-
temperature and low-pressure alarm and switch-off, and safe standby
operation. All features are connected to the Claus plants process con-
trol system.
An efcient mixing device ensures even oxygen distribution in the
Claus air. A proprietary Claus burner was developed especially for ap-
plication for air- and oxygen-enriched operations. This burner provides
for a short and highly turbulent ame, which ensures good approach
toward equilibrium for Claus operation and for the decomposition of
ammonia.
Economics: As oxygen enrichment provides substantial additional Claus
capacity, it is a low-cost alternative to building an additional Claus plant.
It can save investment, manpower and maintenance.
Installed cost for oxygen enrichment per level 1 is typically below
$250,000. For level 2, the investment costs range from $200,000 to
$500,000 and depend on the size of the Claus plant. Operating costs
are varied and depend on the duration of oxygen usage. Typically, an-
nual costs of oxygen enrichment are estimated as 10% to 40% of the
cost for a Claus plant, providing the same additional sulfur capacity.

Continued
Installations: Over 10, plus numerous test installations to quantify the
effects of capacity increase and ammonia decomposition
Reference: Reinhardt, H. J. and P. M. Heisel, Increasing the capacity of
Claus plants with oxygen, Reports on Science and Technology, No. 61
(1999), p. 2 ff.
Contributor: Linde AG, Gas Division.
Oxygen enrichment for Claus units, continued
Oxygen enrichment for FCC units
Application: Increase the throughput capacity by up to 50% and/or con-
version in FCC units; process heavier feeds
Description: Clean fuels regulations are being implemented. Plus, the de-
mand for transport fuels continually shifts toward more kerosine and diesel.
The reason is that the regulations and the change in demand are totally in-
dependent developments. But both contribute to the requirement of more
exibility in the uid catalytic cracking units (FCCUs). Consequently, FCCUs
require more exibility to treat a wider range of feeds, especially heavier
feeds, and increasing throughput capacity. Both goals can be achieved via
oxygen enrichment in the FCC regeneration.
In the FCC reactor, long-chain hydrocarbons are cleaved into shorter
chains in a uidized-bed reactor at 450 550C. This reaction produces
coke as a byproduct that deposits on the catalyst. To remove the coke
from the catalyst, it is burned off at 650 750C in the regenerator. The
regenerated catalyst is returned to the reactor.
Oxygen enrichment, typically 27 vol% oxygen, intensies catalyst re-
generation and can substantially raise throughput capacity and/or conver-
sion of the FCC unit.
Oxygen sources can be liquid oxygen tanks, onsite ASUs or pipe-
line supply. Oxygen consumption in FCC units uctuates widely in most
cases; thus, tanks are the best choice with respect to ease of operation,
exibility and economy.
For oxygen addition into the CS air duct, a number of safety rules
must be observed. The oxygen metering device FLOWTRAIN contains all
necessary safety features, including ow control, low-temperature and
low-pressure alarm and switch-off, and safe standby operation. All of
these features are connected to the FCC units process control system.
An efcient mixing device ensures even oxygen distribution in the air
feed to the FCC regeneration.
Economics: Oxygen enrichment in FCC regeneration is economically
favorable in many plants. For example, one renery increased through-
put by 15%. The net improvement was a 26% increase in higher-value
products, such as naphtha. Likewise, lower value products increased
only 5%, as fuel gas. The net prot increased substantially.
Installed cost for oxygen enrichment is typically below $250,000.
Operating costs will depend on the cost for oxygen and the duration
of oxygen enrichment. Economical oxygen usage can be calculated on
a case-by-case basis and should include increased yields of higher-value
products and optional usage of lower value feeds.
Installations: Currently, two units are in operation, plus test installations
to quantify the effects of higher capacity and conversion levels.
Reference: Heisel, M. P., C. Morn, A. Reichhold, A. Krause, A. Berlanga,
Cracking with Oxygen, to be published in Linde Technology 1, 2004.
Contributor: Linde AG, Gas Division.

Paraxylene
Application: CrystPX is a modern crystallization technology to produce
high-purity paraxylene (PX). This process offers lower capital cost and ap-
plies a simpler process scheme when compared to other technologies.
CrystPX can be used in grassroots designs as a more economical alterna-
tive to adsorption processes, or applied in various revamp congurations
to improve product purity, increase capacity or lower operating costs.
Description: CrystPX uses reliable suspension crystallization as the meth-
od to produce PX from a mixture of C
8
aromatics. The technology incor-
porates an optimized arrangement of equipment to conserve the cool-
ing energy and reduce recycle rates. A pusher-type centrifuge separates
PX crystals from the mother liquor, which is recycled to another stage,
or xylene isomerization unit. The number of stages required is set by
the feedstock composition and recovery required. The PX crystals are
washed with paraxylene product, avoiding the use of other components
that must subsequently be separated.
This process is economical to use with equilibrium xylene feedstock
(20 25% PX); or with more concentrated feeds, such as originating
from selective toluene conversion processes. In these cases, the process
technology is even more economical to produce high-purity PX product.
This technology takes advantage of recent advances in crystallization
techniques and advancements in equipment to create this economically
attractive method for PX recovery and purication.
The design uses only crystallizers and centrifuges in the primary op-
eration. This simplicity of equipment promotes low maintenance costs,
easy incremental expansions and controlled exibility. For the case with
concentrated feedstock, high-purity PX is produced in the front section
of the process at warm temperatures, taking advantage of the high con-
centration of PX present in the feed. At the back end of the process, ad-
ditional PX recovery is obtained through a series of crystallizers operated
successively at colder temperatures. This scheme minimizes the need
for recycling excessive amounts of ltrate, thus reducing total energy
requirements.
Process advantages include:
High PX purity and recovery (99.8 + wt.% purity at up to 95%
recovery)
Crystallization equipment is simple, easy to procure and opera-
tionally trouble free
Compact design requires small plot size, and lowest capital invest-
ment
Operation is exible to meet market requirements for PX purity
System is easily amenable to future requirement for incremental
capacity increases
Feed concentration of PX is used efciently
Technology is exible to process a range of feed concentrations
(20 95 wt.% PX) using a single or multistage system.
Aromatics complex using CrystPX technology is cost competitive
with adsorption-based systems for PX recovery
Continued
Economics: Table 1 lists the benets of the CrystPX process.
TABLE 1. Techno-economic comparison of CrystPX to conventional
technologies
Basis: 90% PX feed purity, 400,000 tpy of 99.9 wt% PX
CrystPX Other crystallization technologies
Investment cost, $MM 26.0 40.0
Paraxylene recovery, % 95 95
Electricity consumption, kWh/ ton PX 50 80
Operation mode Continuous Batch
Note: CrystPX is a proprietary process technology marketed and licensed
by GTC Technology Inc., in alliance with Lyondell Chemical Co.
Paraxylene, continued
Prereforming with feed
ultra purification
Application: Ultra-desulfurization and adiabatic-steam reforming of hy-
drocarbon feed from renery offgas or natural gas through LPG to naph-
tha feeds as a prereforming step in the route to hydrogen production.
Description: Sulfur components contained in the hydrocarbon feed are
converted to H
2
S in the HDS vessel and then fed to two desulfurization
vessels in series. Each vessel contains two catalyst typesthe rst for
bulk sulfur removal and the second for ultrapurication down to sulfur
levels of less than 1 ppb.
The two-desulfurization vessels are arranged in series in such a way
that either may be located in the lead position allowing online change
out of the catalysts. The novel interchanger between the two vessels
allows for the lead and lag vessels to work under different optimized
conditions for the duties that require two catalyst types. This arrange-
ment may be retrotted to existing units.
Desulfurized feed is then fed to a xed bed of nickel-based catalyst
that converts the hydrocarbon feed, in the presence of steam, to a prod-
uct stream containing only methane together with H
2
, CO, CO
2
and
unreacted steam which is suitable for further processing in a conven-
tional red reformer. The CRG prereformer enables capital cost savings
in primary reforming due to reductions in the radiant box heat load. It
also allows high-activity gas-reforming catalyst to be used. The ability to
increase preheat temperatures and transfer radiant duty to the convec-
tion section of the primary reformer can minimize involuntary steam
production.
Operating conditions: The desulfurization section typically operates be-
tween 170 C and 420 C and the CRG prereformer will operate over a
wide range of temperatures from 250 C to 650 C and at pressures up
to 75 bara.
Installation: CRG process technology covers 40 years of experience with
over 150 plants built and operated. Ongoing development of the cata-
lyst has lead to almost 50 such units since 1990.
Catalyst: The CRG catalyst is manufactured under license by Synetix.
Licensor: The process and CRG catalyst are licensed by Davy Process
Technology.


Application: Selective conversion of gas oil and heavy residual feed-
stocks.
Products: High-octane gasoline, distillate and C
3
C
4
olens.
Description: For residue cracking the process is known as R2R (reactor2
regenerators). Catalytic and selective cracking occurs in a short-contact-
time riser (1) where oil feed is effectively dispersed and vaporized through a
proprietary feed-injection system. Operation is carried out at a temperature
consistent with targeted yields. The riser temperature prole can be opti-
mized with the proprietary mixed temperature control (MTC) system (2).
Reaction products exit the riser-reactor through a high-efciency,
close-coupled, proprietary riser termination device RS
2
(riser separator
stripper) (3). Spent catalyst is pre-stripped followed by an advanced
high-efciency packed stripper prior to regeneration. The reaction prod-
uct vapor may be quenched using BPs proprietary technology to give
the lowest dry gas and maximum gasoline yield. Final recovery of cata-
lyst particles occurs in cyclones before the product vapor is transferred
to the fractionation section.
Catalyst regeneration is carried out in two independent stages (4,
5) equipped with proprietary air and catalyst distribution systems re-
sulting in fully regenerated catalyst with minimum hydrothermal deac-
tivation, plus superior metals tolerance relative to single-stage systems.
These benets are derived by operating the rst-stage regenerator in a
partial-burn mode, the second-stage regenerator in a full-combustion
mode and both regenerators in parallel with respect to air and ue gas
ows. The resulting system is capable of processing feeds up to about
6 wt% ConC without additional catalyst cooling means, with less air,
lower catalyst deactivation and smaller regenerators than a single-stage
regenerator design. Heat removal for heavier feedstocks (above 6 CCR)
may be accomplished by using a reliable dense-phase catalyst cooler,
which has been commercially proven in over 24 units and is licensed
exclusively by Stone & Webster/Axens.
The converter vessels use a cold-wall design that results in mini-
mum capital investment and maximum mechanical reliability and safety.
Reliable operation is ensured through the use of advanced uidization
technology combined with a proprietary reaction system. Unit design
is tailored to reners needs and can include wide turndown exibility.
Available options include power recovery, wasteheat recovery, ue-gas
treatment and slurry ltration.
Existing gas oil units can be easily retrotted to this technology. Re-
vamps incorporating proprietary feed injection and riser termination de-
vices and vapor quench result in substantial improvements in capacity,
yields and feedstock exibility within the mechanical limits of the exist-
ing unit.

Continued
Installation: Stone & Webster and Axens have licensed 27 full-technol-
ogy R2R units and performed more than 150 revamp projects.
Reference: Letzsch, W. S., Commercial performance of the latest FCC
technology advances, NPRA Annual Meeting, March 2000.
Licensor: Stone & Webster Inc., a Shaw Group Co., and Axens, IFP
Group Technologies.
Resid catalytic cracking, continued
SBS SO
3
removal process
Application: SBS is a patented process used for high level of SO
3
reduc-
tion with either wet scrubbing systems or dry systems such as an ESP.
When used in conjunction with BELCOs wet scrubbing system, and the
LoTOx* process, one can achieve simultaneously very high reduction of
particulate, SO
2
, SO
3
and NO
x
in a single scrubber vessel.
Description: SBS injection technology uses sodium bisulte ( SBS ) as the
reagent. A clear solution of sodium bisulte is injected into the hot ue
gas stream upstream of the emission control devices used to remove
particulate and SO
2
from the ue gas. SO
3
in the ue gas reacts with
the injected SBS to produce dry sodium sulfate and sodium bisulfate
particles, which are removed downstream along with the other particu-
late.
The reaction rates are fast; so, only short residence times are required
between reagent injection and the downstream particulate collection
device. Both sodium bisulte ( NaHSO
3
) and sodium sulte ( Na
2
SO
3
)
make up the reagent feed. Because the reactions are specic to SO
3
,
very little reagent is injected.
Operating conditions: SBS injection occurs in the ue-gas duct upstream
of the scrubber or ESP, at atmospheric pressure and typical ue-gas tem-
peratures. High particulate and sulfur levels do not cause problems for
this process.
Economics: When very high levels of SO
3
reduction are required, the
SBS process is extremely competitive against alternate processes and
equipment.
Development status: Full-scale applications of the process have been
operating successfully at several large power station applications in
the US.
* LoTox is a trademark of The BOC Group.
Reference: Weaver, Barrasso and Jarvis, An update of wet scrubbing
control technology for FCCU-multiple pollutant control, NPRA Annual
Meeting, San Antonio, March 2003.
Licensor: Belco Technologies Corp., as a sub-licensor for Codan Devel-
opment LLC.
SO
2
removal, regenerative
Application: Regenerative scrubbing system to recover SO
2
from ue gas
containing high SO
2
levels such as gas from FCC regenerator or inciner-
ated SRU tail gas and other high SO
2
applications. The LABSORB process
is a low pressure drop system and is able to operate under varying condi-
tions and not sensitive to variations in the upstream processes.
Products: The product from the LABSORB process is a concentrated SO
2
stream consisting of approximately 90% SO
2
and 10% moisture. This
stream can be sent to the front of the SRU to be mixed with H
2
S and
form sulfur, or it can be concentrated for other marketable uses.
Description: Hot dirty ue gas is cooled in a ue-gas cooler or waste-
heat recovery boiler prior to entering the systems. Steam produced can
be used in the LABSORB plant. The gas is then quenched to adiabatic
saturation (typically 50C75C) in a quencher/pre-scrubber; it proceeds
to the absorption tower where the SO
2
is removed from the gas. The
tower incorporates multiple internal and re-circulation stages to ensure
sufcient absorption.
A safe, chemically stable and regenerable buffer solution is con-
tacted with the SO
2
-rich gas for absorption. The rich solution is then
piped to a LABSORB buffer regeneration section where the solution is
regenerated for re-use in the scrubber. Regeneration is achieved using
low-pressure steam and conventional equipment such as strippers, con-
densers and heat exchangers.
Economics: This process is very attractive at higher SO
2
concentrations
or when liquid or solid efuents are not allowed. The systems buffer
loss is very low, contributing to a very low operating cost. Additionally,
when utilizing LABSORB as an SRU tail-gas treater, many components
normally associated with the SCOT process are not required; thus saving
considerable capital.
Installations: One SRU tail-gas system and two FCCU scrubbing systems.
Reference: Confuorto, Weaver and Pedersen, LABSORB regenerative
scrubbing operating history, design and economics, Sulfur 2000, San
Francisco, October 2000.
Confuorto, Eagleson and Pedersen, LABSORB, A regenerable wet
scrubbing process for controlling SO
2
emissions, Petrotech-2001, New
Delhi, January 2001.
Licensor: Belco Technologies Corp.

Sour gas treatment
Application: The WSA process (Wet gas Sulfuric Acid) treats all types of
sulfur-containing gases such as amine and Rectisol regenerator offgas,
SWS gas and Claus plant tail gas in reneries, gas treatment plants,
petrochemicals and coke chemicals plants. The WSA process can also be
applied for SO
x
removal and regeneration of spent sulfuric acid.
Sulfur, in any form, is efciently recovered as concentrated commer-
cial-quality sulfuric acid.
Description: Feed gas is combusted and cooled to approximately
420C in a waste heat boiler. The gas then enters the SO
2
converter
containing one or several beds of SO
2
oxidation catalyst to convert SO
2

to SO
3
. The gas is cooled in the gas cooler whereby SO
3
hydrates to
H
2
SO
4
(gas), which is nally condensed as concentrated sulfuric acid
(typically 98% w/w).
The WSA condenser is cooled by ambient air, and heated air may be
used as combustion air in the burner for increased thermal efciency. The
heat released by incineration and SO
2
oxidation is recovered as steam.
The process operates without removing water from the gas. Therefore,
the number of equipment items is minimized, and no liquid waste is
formed. Cleaned process gas leaving the WSA condenser is sent to stack
without further treatment.
The WSA process is characterized by:
More than 99% recovery of sulfur as commercial-grade
sulfuric acid
No generation of waste solids or wastewater
No consumption of absorbents or auxiliary chemicals
Efcient heat recovery ensuring economical operation
Simple and fully automated operation adapting to variations in
feed gas ow and composition.
Installation: More than 45 units worldwide.
Spent acid regeneration

Application: The WSA process (Wet gas Sulfuric Acid) treats spent sulfu-
ric acid from alkylation as well as other types of waste sulfuric acid in the
petrochemical and coke chemicals industry. Amine regenerator offgas
and /or renery gas may be used as auxiliary fuel. The regenerated acid
will contain min. 98% H
2
SO
4
and can be recycled directly to the alkyla-
tion process.
The WSA process is also applied for conversion of H
2
S and removal
of SO
x
.
Description: Spent acid is decomposed to SO
2
and water in a burner
using amine regenerator offgas or renery gas as fuel. The SO
2
contain-
ing ue gas is cooled in a waste-heat boiler and solid matter originating
from the acid feed is separated in an electrostatic precipitator. By add-
ing preheated air, the process gas temperature and oxygen content are
adjusted before the catalytic converter when converting SO
2
to SO
3
. The
gas is cooled in the gas cooler whereby SO
3
is hydrated to H
2
SO
4
(gas),
which is nally condensed as 98% sulfuric acid.
The WSA condenser is cooled by ambient air; the heated air may be
used as combustion air in the burner for increased thermal efciency. The
heat released by incineration and SO
2
oxidation is recovered as steam.
The process operates without removing water from the gas. There-
fore, the number of equipment items is minimized and no liquid waste
is formed. This is especially important in spent acid regeneration where
SO
3
formed by the acid decomposition will otherwise be lost with the
wastewater.
The WSA process is characterized by:
More than 99% recovery of sulfuric acid
No generation of waste solids or wastewater
No consumption of absorbents or auxiliary chemicals
Efcient heat recovery ensuring economical operation
Simple and fully automated operation adapting to variations in
feed ow and composition.
Installation: More than 45 WSA units worldwide, including 8 for spent
acid regeneration.

Spent lube oil re-refining

Application: The Revivoil process can be used to produce high yields of
premium quality lube bases from spent motor oils. Requiring neither
acid nor clay treatment steps, the process can eliminate environmental
and logistical problems of waste handling and disposal associated with
conventional re-rening schemes.
Description: Spent oil is distilled in an atmospheric ash distillation
column to remove water and gasoline and then sent to the Thermal
Deasphalting (TDA) vacuum column for recovery of gas oil overhead
and oil bases as side streams. The energy-efcient TDA column features
excellent performance with no plugging and no moving parts. Metals
and metalloids concentrate in the residue, which is sent to an optional
Selectopropane unit for brightstock and asphalt recovery. This scheme
is different from those for which the entire vacuum column feed goes
through a deasphalting step; Revivoils energy savings are signicant,
and the overall lube oil base recovery is maximized. The results are sub-
stantial improvements in selectivity, quality and yields.
The nal, but very important step for base oil quality is a specic
hydronishing process that reduces or removes remaining metals and
metalloids, Conradson Carbon, organic acids, and compounds contain-
ing chlorine, sulfur and nitrogen. Color, UV and thermal stability are
restored and polynuclear aromatics are reduced to values far below the
latest health thresholds. Viscosity index remains equal to or better than
the original feed. For metal removal (> 96%) and rening-purication
duty, the multicomponent catalyst system is the industrys best.
Product quality: The oil bases are premium products; all lube oil base
specications are met by Revivoil processing from Group 1 through
Group 2 of the API basestocks denitions. Besides, a diesel can be ob-
tained, in compliance with the EURO 5 requirements (low sulfur).
Health & safety and environment: The high-pressure process is in line
with future European specications concerning carcinogenic PNA com-
pounds in the nal product at a level inferior to 5 wppm (less than 1
wt% PCA - IP346 method).
Economics: The process can be installed stepwise or entirely. A simpler
scheme consists of the atmospheric ash, TDA and hydronishing unit
and enables 70 80% recovery of lube oil bases. The Selectopropane
unit can be added at a later stage, to bring the oil recovery to the 95%
level on dry basis. Economics below show that for two plants of equal
capacity, payout times before taxes are two years in both cases.
Investment: Basis 100,000 metric tpy, water-free, ISBL 2004 Gulf
Coast, million US$
Configuration 1 (Atm. ash, TDA and Hydronishing units) 30
Configuration 2 (Same as above + Selectopropane unit) 35

Continued
Utilities: Basis one metric ton of water-free feedstock
Config. 1 Config. 2
Electrical power, kWh 45 55
Fuel, million kcal 0.62 0.72
Steam, LP, kg 23.2
Steam, MP, kg 872 890
Water, cooling, m
3
54 59
Installation: Ten units have been licensed using all or part of the Revivoil
Technology.
Licensor: Axens and Viscolube SpA.
Spent oil lube re-refining, continued
Sulfur degassing
Application: Hydrogen sulde (H
2
S) removal from sulfur.
Description: Sulfur, as produced by the Claus process, typically contains
from about 200 ppmw to 500 ppmw H
2
S. The H
2
S may be contained in
the molten sulfur as H
2
S or as hydrogen polysuldes (H
2
S
x
). The dissolved
H
2
S separates from the molten sulfur readily, but the H
2
S
x
does not.
The sulfur degassing process accelerates the decomposition of hy-
drogen polysuldes to H
2
S and elemental sulfur (S). The dissolved H
2
S
gas is released in a controlled manner. Sulfur temperature, residence
time and the degree of agitation all inuence the degassing process.
Chemical catalysts, including oxygen (air) that accelerate the rate of H
2
S
x
decomposition are known to improve the degassing characteristics.
In fact, the majority of successful commercial degassing processes
use compressed air, in some fashion, as the degassing medium. Research
performed by Alberta Sulphur Research Ltd. has demonstrated that air is
a superior degassing agent when compared to nitrogen, steam or other
inert gases. Oxygen present in air promotes a level of direct oxidation of
H
2
S to elemental S, which reduces the gaseous H
2
S partial pressure and
increases the driving force for H
2
S
x
decomposition to the more easily
removed gaseous phase H
2
S.
The MAG degassing system concept was developed to use the
benets of degassing in the presence of air without relying on a costly
compressed air source. With the MAG system, motive pressure from a
recirculated degassed sulfur stream is converted to energy in a mixing
assembly within the undegassed sulfur. The energy of the recirculated
sulfur creates a high air-to-sulfur interfacial area by generating intense
turbulence within the jet plume turning over the contents many times,
thus exposing the molten sulfur to the sweep air. Intimate mixing is
achieved along with turbulence to promote degassing. This sulfur de-
gassing system can readily meet a 10 ppmw total H
2
S (H
2
S + H
2
S
x
)
specication.
Tests show degassing rate constants nearly identical to traditional air
sparging for well-mixed, air-swept degassing systems. Thus, comparable
degassing to air sparging can be achieved without using a compressed
air source. The assemblies are designed to be self-draining of molten
sulfur and to be easily slipped in and out for maintenance through the
pit nozzles provided. The mixing assemblies require no moving parts or
ancillary equipment other than the typical sulfur-product-transfer pump
that maximizes unit reliability and simplies operations.
The process is straightforward; it is inherently safer than systems
using spray nozzles and/or impingement plates because no free fall of
sulfur is allowed.
Economics: Typically does not require changes to existing sulfur process-
ing infrastructure.
Continued
Installation: Several units are in design.
Reference: US Patent 5935548 issued Aug. 10, 1999.
Licensor: Black & Veatch Pritchard, Inc.
Sulfur degassing, continued
Sulfur recovery
Application: The COPE process for O
2
enrichment is utilized to increase
capacity and recovery of existing Claus sulfur recovery / tail gas cleanup
units, provide redundant sulfur processing capacity, and improve com-
bustion performance of units processing lean acid gas.
Description: The sulfur processing capacity of typical Claus sulfur recovery
units can be increased to more than 200% of the base capacity through
partial to complete replacement of combustion air with pure O
2
. SRU ca-
pacity is typically limited by hydraulic pressure drop. As O
2
replaces combus-
tion air, the quantity of inert nitrogen is reduced, allowing additional acid
gas to be processed. The process can be implemented in two stages.
As the O
2
enrichment level increases, the combustion temperature (1)
increases. COPE Phase I, which does not use a recycle stream, can often
achieve 50% capacity increase through O
2
enrichment to the maximum
reaction furnace refractory temperature limit of about 2,700 2,800F.
Higher O
2
enrichment levels are possible with COPE Phase II which uses
an internal process recycle stream to moderate the combustion tempera-
ture allowing enrichment up to 100% O
2
. Flow through the remainder of
the SRU (2, 3, & 4) and the tail gas cleanup unit is greatly reduced.
Ammonia and hydrocarbon acid gas impurity destruction and ther-
mal stage conversion are improved at the higher O
2
enriched combustion
temperatures. Total SRU sulfur recovery is increased by 0.5 to 1%. A single
proprietary COPE burner handles acid gas, recycle gas, air and oxygen.
Operating conditions: Combustion pressure from 6 to 12 psig; combus-
tion temperature up to 2,800F. Oxygen concentration from 21% to
100%. SRU sulfur recovery is 95 98%.
Economics: Expanded SRU and tail gas unit retrot sulfur processing
capacity at capital cost of 15 25% of new plant cost. New plant sav-
ings of up to 25%, and redundant capacity at 15% of base capital cost.
Operating costs are a function of oxygen cost, reduced incinerator fuel,
and reduced operating and maintenance labor costs.
Installations: Twenty-one COPE trains in operation at twelve locations.
Reference: US Patents 4,552,747 and 6,508,998.
Sala, L., W. P. Ferrell, and P. Morris, The COPE processincrease
sulfur recovery capacity to meet changing needs, European Fuels Week
Conference, Giardini Naxos, Taormina, Italy, April 2000.
Nasato, E., and T. A. Allison, COPE EjectorProven Technology,
Sulphur 2002, Vienna, Austria, October 2002.
Licensor: Goar, Allison & Associates, Inc. and Air Products and Chemi-
cals, Inc.

Sulfur recovery
Application: Removal of dissolved H
2
S and H
2
S
x
from produced liquid
sulfur by the DGAASS process. Undegassed sulfur can create odor
problems and poses toxic and explosive hazards during the storage and
transport of liquid sulfur.
Description: Degasication is accomplished in a pressurized vertical vessel
where undegassed sulfur is efciently contacted with pressurized process
air (instrument or clean utility air). The contactor vessel may be located at
any convenient location. The undegassed sulfur is pumped to the vessel
and intimately contacted with air across special xed vessel internals.
Operation at elevated pressure and a controlled temperature accel-
erates the oxidation of H
2
S and polysuldes (H
2
S
x
) to sulfur.
The degassed sulfur can be sent to storage or directly to loading
without additional pumping. Operation at elevated pressure allows the
overhead vapor stream to be routed to the traditional incinerator loca-
tion, or to the SRU main burner or TGTU line burnerthus eliminating
the degassing unit as an SO
2
emission source.
Economics: DGAASS achieves 10 ppmw combined H
2
S / H
2
S
x
in prod-
uct sulfur. Elevated pressure results in the following benets: low capital
investment, very small footprint, low operating cost and low air require-
ment. Operation is simple, requiring minimal operator and maintenance
time. No chemicals or catalysts are required.
Installations: Sixteen units in operation. Eighteen additional trains in en-
gineering and construction phase with total capacity over 19,000 ltpd.
Reference: US Patent 5,632,967.
Nasato, E., and T. A. Allison, Sulfur DegasicationThe DGAASS
Process, Proceedings of the 1998 Laurance Reid Gas Conditioning
Conference, Norman, Oklahoma, March 1998.
Fenderson, S., Continued development of the DGAASS sulfur de-
gasication process, Brimstone Sulfur Recovery Symposium, Canmore,
Alberta, May 2001.
Licensor: Goar, Allison & Associates, Inc.
Thermal gasoil process

Application: The Shell Thermal Gasoil process is a combined residue and
waxy distillate conversion unit. The process is an attractive low-cost con-
version option for hydroskimming reneries in gasoil-driven markets or
for complex reneries with constrained waxy distillate conversion capac-
ity. The typical feedstock is atmospheric residue, which eliminates the
need for an upstream vacuum asher. This process features Shell Soaker
Visbreaking technology for residue conversion and an integrated recycle
heater system for the conversion of waxy distillate.
Description: The preheated atmospheric (or vacuum) residue is charged
to the visbreaker heater (1) and from there to the soaker (2). The con-
version takes place in both the heater and soaker and is controlled by
the operating temperature and pressure. The soaker efuent is routed
to a cyclone (3). The cyclone overheads are charged to an atmospheric
fractionator (4) to produce the desired products including a light waxy
distillate. The cyclone and fractionator bottoms are routed to a vacuum
asher (6), where waxy distillate is recovered. The combined waxy distil-
lates are fully converted in the distillate heater (5) at elevated pressure.
Yields: Depend on feed type and product specications.
Feed atmospheric residue Middle East
Viscosity, cSt @ 100C 31
Products, % wt.
Gas 6.4
Gasoline ECP 165C 12.9
Gasoil ECP 350C 38.6
Residue ECP 520C+ 42.1
Viscosity 165C plus, cSt @100C 7.7
Economics: The investment amounts to 1,400 1,600 US$/bbl installed
excluding treating facilities and depending on capacity and congura-
tion (basis: 1998).
Utilities, typical consumption per bbl of feed @ 180C:
Fuel, 10
3
cal 34
Water, cooling, m
3
0.17
Installation: Thirteen Shell thermal gasoil units have been built or are
under construction. Post startup services and technical services on exist-
ing units are available from Shell.
Reference: Thermal Conversion Technology in Modern Power Integrat-
ed Renery Schemes, 1999 NPRA Annual Meeting.
Continued
Licensor: Shell Global Solutions International B.V., and ABB Lummus
Global B.V.
Thermal gasoil process, continued
Treatinggases
Application: AMINEX and THIOLEX systems extract H
2
S, COS and CO
2
from gases with amine or caustic solution using FIBER-FILM Contactor
technology.
Description: In an AMINEX system, the amine phase ows along the
bers of the FIBER-FILM Contactor as it preferentially wets the bers.
Hydrocarbon also ows through the contactor parallel to the amine-
wetted bers where the H
2
S, COS and/or CO
2
are extracted into the
aqueous phase. The two phases disengage in the separator vessel with
the rich amine owing to the amine regeneration unit and the treated
gas owing to storage.
Similarly, a THIOLEX system uses the same process utilizing caustic
to preferentially wet the bers where the H
2
S, COS and CO
2
are ex-
tracted into the caustic phase. The rich caustic ows to suldic caustic
storage, and treated gas ows to storage. MEA can be added to the
fresh caustic to catalyze the hydrolysis of COS into H
2
S and CO
2
which
are subsequently removed by the caustic phase.
Competitive advantages: FIBER-FILM Contactor technology requires
smaller processing vessels, allowing for shorter separation times and less
suldic treating solution generation. Result: Saving valuable plant space
and reducing capital expenditures.
Installations: Three installations worldwide in THIOLEX service.
Reference: Hydrocarbon Processing, Vol. 63, No. 4, April 1984, p. 87.
Licensor: Merichem Chemicals & Renery Services LLC.

Treatinggasoline
Application: MERICAT systems oxidize mercaptans to disuldes in gaso-
line or condensate by reacting mercaptans with air and caustic in the
presence of catalyst using FIBER-FILM Contactor technology.
Description: In a MERICAT system, the caustic phase ows along the -
bers of the FIBER-FILM Contactor as it preferentially wets the bers. The
hydrocarbon mixes with air through a proprietary air sparger and ows
through the caustic-wetted bers where the mercaptans are converted
to disuldes in the caustic phase and are absorbed back into the hydro-
carbon phase. The two phases disengage and the phenolic caustic ows
to storage or can be shipped to Merichem as a product.
smaller processing vessels, allowing for shorter separation times and
less waste generation. Result: Saving valuable plant space and reducing
capital expenditures.
Installations: 121 installations worldwide.
Treatinggasoline and light

hydrocarbon liquids
Application: THIOLEX/REGEN systems extract H
2
S and mercaptans from
gases and light liquid streams, including gasoline, with caustic using
FIBER-FILM Contactor technology. It can also be used to hydrolyze COS
contained in LPG.
Description: In a THIOLEX system, the caustic phase ows along the
bers of the FIBER-FILM Contactor as it preferentially wets the bers. Hy-
drocarbon also ows through the caustic-wetted bers where the H
2
S
and mercaptans are extracted into the caustic phase. The two phases
disengage and the caustic ows to the REGEN where the suldic caustic
is regenerated using air and catalyst. The disulde oil formed in this re-
action may be removed via gravity separation, FIBER-FILM solvent wash-
ing or a combination of the two. The regenerated caustic ows back to
the THIOLEX system for continued re-use.
less suldic caustic generation. Result: Saving valuable plant space and
reducing capital expenditures.
Reference: Oil & Gas Journal, August 12, 1985, p. 78.
Treatinggasoline desulfurization,
ultra deep
Application: EXOMER extracts recombinant mercaptan sulfur from se-
lectively hydrotreated FCC gasoline streams with a proprietary treating
solution. This is done using FIBER-FILM Contactor technology to reduce
total sulfur content. EXOMER is jointly developed with ExxonMobil Re-
search & Engineering Co.
Description: In an EXOMER system, the lean treating solution phase
ows along the bers of the FIBER-FILM Contactor, along with the hy-
drocarbon phase, allowing the recombinant mercaptans to be extracted
into the treating solution in a non-dispersive manner. The two phases
disengage in the separator vessel with the treated hydrocarbon owing
to storage.
The separated rich treating solution phase is sent to the regenera-
tion unit where sulfur-bearing components are removed. The removed
sulfur is sent to another renery unit for further processing. After pol-
ishing, the lean treating solution is returned to the extraction step for
further use.
Economics: EXOMER allows reners to meet new stricter sulfur speci-
cations while preserving octane. The capital expenditure for a grass roots
EXOMER solution is 3550% of the cost of most incremental conven-
tional hydrotreating solutions. Operating costs per barrel can be more
than 6070% less than conventional hydrotreating.
FIBER-FILM Contactor technology requires smaller processing ves-
sels; thus, allowing for shorter separation times and less spent treating
solution generation. Result: Saving valuable plant space and reducing
Installations: Three installations worldwide.
Reference: Hydrocarbon Processing, February 2002, p. 45.
Application: NAPFINING/MERICATII/AQUAFINING systems remove naph-
thenic acids and/or mercaptans from kerosine with caustic, air and cata-
lyst using FIBER-FILM Contactor technology followed by an upow cata-
lyst impregnated carbon bed.
Description: In the NAPFINING system, the caustic phase ows along
the bers of the FIBER-FILM Contactor as it preferentially wets the -
bers. Kerosine simultaneously ows through the caustic-wetted bers
where naphthenic acids react with the caustic phase to form sodium
naphthenate. The two phases disengage and the kerosine ows to the
MERICAT II where the mercaptans react with caustic, air and catalyst in
the FIBER-FILM Contactor and are subsequently converted to disuldes.
The two phases disengage and the kerosine ows upward through a
catalyst-impregnated carbon bed where any remaining mercaptans are
converted to disuldes.
An AQUAFINING system is then used to wash any sodium entrained
in the kerosine leaving the MERICAT II vessel. Salt driers and clay lters
may be used to remove additional water, surfactants and particulates to
ensure a completely clean stream.
Reference: Hydrocarbon Technology International, 1993.

Application: AMINEX extracts H
2
S, COS and CO
2
from light-liquid streams
with an amine solution using FIBER-FILM Contactor technology.
Description: In an AMINEX system, the amine phase ows along the bers
of the FIBER-FILM Contactor as it preferentially wets the bers. Hydrocar-
bon also ows through the amine-wetted bers where the H
2
S, COS and/
or CO
2
are extracted into the amine phase. The two phases disengage in
the separator vessel with the rich amine owing to the amine regenera-
tion unit and the treated light liquids owing to storage.
smaller processing vessels, allowing for shorter separation times and less
suldic treating solution generation. Result: Saving valuable plant space
and reducing capital expenditures.
Installations: Twelve installations worldwide.
Reference: Hydrocarbon Processing, Vol. 63, No. 4, April 1984, p. 87.
Application: ECOMERICAT removes phenols from phenolic caustics us-
ing a FIBER-FILM Contactor while neutralizing the free caustic content.
Description: In an ECOMERICAT system, the spent caustic is contacted
with a slipstream of sweetened gasoline and CO
2
whereby the sprung
phenols are extracted into the gasoline and the free caustic is neutral-
ized, yielding neutral brine with minimal COD.
Competitive advantages are:
Minimizes disposal cost at existing efuent caustic processing fa-
cilities.
Reduces phenol content of spent caustic and returns value to the
gasoline product.
Operates over a wide pH range.
Simple to operate.
Installations: One installation worldwide.

Application: CHLOREX removes inorganic chloride compounds from liq-
uid and gas reformer products using a FIBER-FILM Contactor and an
alkaline water treating solution.
Description: The CHLOREX system uses an alkaline water solution to
react chloride impurities contained in the reformate feeding the stabi-
lizer or the overhead product with sodium hydroxide. Fresh caustic and
fresh process water are added to the system to maintain the pH of the
recycle solution. Water makeup is set to maintain the total sodium of
the recycled solution within a specied range.
Installations: Four installations worldwide.

Treatingspent caustic deep

neutralization
Application: MERICON systems neutralize spent caustics containing sul-
des, mercaptans, naphthenic acids and phenols.
Description: In a MERICON system, spent caustic is neutralized with acid
to a low pH. The sprung acid oils are separated from the low pH brine.
The resulting acid gases (H
2
S and mercaptans) ow to a sulfur plant.
Any acid oils produced in the neutralization reaction are returned to the
renery for processing. The acidied brine is further stripped with fuel
gas to remove traces of H
2
S and mercaptans. The brine is mixed with
caustic to return it to a neutral pH.
Minimal operator attention and 100% onstream factor between
turnarounds
Minimal capital investment with over 70 years of knowhow
Maximum COD reduction
Non-odorous neutralized brine product.
Installations: Nineteen installations worldwide.
Reference: Petroleum Technology Quarterly, Spring 2001, p. 55.

Treatingsweetening
Application: MERICAT II oxidizes mercaptan sulfur components to di-
suldes to reduce product corrosivity and odor. The streams treated
are jet fuel, kerosine, natural gasoline and selectively hydrotreated FCC
gasolines.
Description: A MERICAT II system removes mercaptans with a FIBER-
FILM Contactor, air, oxidation catalyst and caustic solution followed by
an upow catalyst-impregnated carbon bed reactor for removal of high-
boiling mercaptans.
Minimal caustic and catalyst consumption
Operating simplicity
Minimal capital investment
Online recausticizing
Liquid sweetening step keeps out organic acids that can plug xed
beds.
Installations: Thirty-two installations worldwide.

Vacuum distillation
Application: Process to produce vacuum distillates that are suitable for
lubricating oil production by downstream units, as well as feedstocks to
FCC and hydrocracker units.
Feeds: Atmospheric bottoms from crude oils (atmospheric residue) or
hydrocracker bottoms.
Products: Vacuum distillates of precisely dened viscosities and ash
points as well as vacuum residue with specied softening point, penetra-
tion and ash point.
Description: Feed is preheated in a heat-exchanger train and fed to the
red heater. The heater-coil temperature is controlled to produce the
required quality of vacuum distillates and residue. Uhde (Edeleanu)-de-
signed units ensure that vaporization occurs in the furnace coils to mini-
mize superheating the residue. Circulating reux streams enable maxi-
mum heat recovery and reduced column diameter.
Wash trays minimize the metals content in the heaviest vacuum
distillate to avoid difculties in downstream lubricating oil production
plants. Heavy distillate from the wash trays is recycled to the heater inlet
or withdrawn as metals cut.
When processing naphthenic residues, a neutralization section may
be added to the fractionator.
3
of feed:
Electricity, kWh 7
Steam, MP, kg 30
Steam production, LP, kg 35
Fuel oil, kg 15
Water, cooling, m
3
10
etary technology are in operation worldwide. The most recent reference
is a complete lube-oil production facility licensed to the state of Turk-
menistan.

Visbreaking
Application: Manufacture incremental gas and distillate products and simul-
taneously reduce fuel oil viscosity and pour point. Also, reduce the amount
of cutter stock required to dilute the resid to meet the fuel oil specications.
Foster Wheeler / UOP offer coil type visbreaking processes.
Products: Gas, naphtha, gas oil, visbroken resid (tar).
Description: In a coil type operation, charge is fed to the visbreaker
heater (1) where it is heated to a high temperature, causing partial va-
porization and mild cracking. The heater outlet stream is quenched with
gas oil or fractionator bottoms to stop the cracking reaction. The va-
por-liquid mixture enters the fractionator (2) to be separated into gas,
naphtha, gas oil and visbroken resid (tar).
Operating conditions: Typical ranges are:
Heater outlet temperature, F 850 910
Quenched temperature, F 710 800
An increase in heater outlet temperature will result in an increase in
overall severity.
Yields:
Feed, source Light Arabian Light Arabian
Type Atm. resid Vac. resid
Sulfur, wt% 3.0 4.0
Concarbon, wt% 8.5 20.3
Viscosity, CKS @ 130 F 150 30,000
CKS @ 210 F 25 900
Products, wt%
Gas 3.1 2.4
Naphtha (C
5
330 F) 7.9 6.0
Gas oil (330 600 F) 14.5 15.5
(1)
Visbroken resid (600 F+) 74.5 76.1
(2)
(1)
330 662F cut for Light Arabian vacuum residue.
(2)
662 F + cut for Light Arabian vacuum residue.
Economics:
Investment (basis: 40,000 10,000 bpsd, 2Q 2004, US Gulf),
$ per bpsd 800 1,600
Fuel, MMBtu 0.1195
Power, kW/bpsd 0.0358
Steam, MP, lb 6.4
Water, cooling, gal 71.0
Installation: Over 50 units worldwide.

Continued
Reference: Handbook of Petroleum Rening Processes, 2nd Ed., Mc-
Graw-Hill, 1997, pp. 12.8312.97.
Licensor: Foster Wheeler/ UOP LLC.
Visbreaking, continued
Visbreaking
Application: The Shell Soaker Visbreaking process is most suitable to re-
duce the viscosity of vacuum (and atmospheric) residues in (semi) complex
reneries. The products are primarily distillates and stable fuel oil. The to-
tal fuel oil production is reduced by decreasing the quantity of cutter stock
required. Optionally, a Shell vacuum asher may be installed to recover
additional gas oil and waxy distillates as cat cracker or hydrocracker feed
from the cracked residue. The Shell Soaker Visbreaking technology has
also proven to be a very cost-effective revamp option for existing units.
Description: The preheated vacuum residue is charged to the visbreaker
heater (1) and from there to the soaker (2). The conversion takes place
in both the heater and the soaker. The operating temperature and pres-
sure are controlled such as to reach the desired conversion level and/
or unit capacity. The cracked feed is then charged to an atmospheric
fractionator (3) to produce the desired products like gas, LPG, naph-
tha, kerosine, gas oil, waxy distillates and cracked residue. If a vacuum
asher is installed, additional gas oil and waxy distillates are recovered
from the cracked residue.
Yields: Vary with feed type and product specications.
Feed, vacuum residue Middle East
Viscosity, cSt @100C 770
Products, wt%
Gas 2.3
Gasoline, 165C EP 4.7
Gas oil, 350C EP 14.0
Waxy distillate, 520C EP 20.0
Residue, 520C+ 59.0
Viscosity, 165C plus, cSt @100C 97
Economics: The investment amounts to 1,000 to 1,400 US$/bbl installed
excluding treating facilities and depending on capacity and the presence
of a vacuum asher (basis: 1998).
Utilities, typical consumption per bbl feed @180C:
Fuel, 10
3
kcal 16
Water, cooling, m
3
0.1
Installation: Eighty-six Shell Soaker Visbreaking units have been built or
are under construction. Post startup services and technical services for
existing units are available from Shell.
Reference: Visbreaking Technology, Erdl und Kohle, January 1986.
Licensor: Shell Global Solutions International B.V. and ABB Lummus
Global B.V.
Wax hydrotreating
Application: Hydrogen nishing technology has largely replaced clay
treatment of low-oil-content waxes to produce food- and medicinal-
grade product specications (color, UV absorbency and sulfur) in new
units. Advantages include lower operating costs, elimination of environ-
mental concerns regarding clay disposal and regeneration, and higher
net wax product yields.
Bechtel has been offering for license the Wax Hy-Finishing process.
Bechtel now is marketing a line of modular, standard hydrogen nish-
ing units for wax treatment. Standard sizes are 500, 1,000, 2,000 and
3,000-bpsd feedrate.
The core of the unit is standardized; however, individual modules are
modied as needed for specic client needs. This unit will be fabricated
to industry standards in a shop environment and delivered to the plant
site as an essentially complete unit. Cost and schedule reductions of at
least 20% over conventional stick-built units are expected. The standard
licensors process guarantees and contractors performance guarantees
(hydraulic and mechanical) come with the modules.
Description: Hard-wax feed is mixed with hydrogen (recycle plus make-
up), preheated, and charged to a xed-bed hydrotreating reactor (1).
The reactor efuent is cooled in exchange with the mixed feed-hydrogen
stream. Gas-liquid separation of the efuent occurs rst in the hot sepa-
rator (2) then in the cold separator (3). The hydrocarbon liquid stream
from each of the two separators is sent to the product stripper (4) to
remove the remaining gas and unstabilized distillate from the wax prod-
uct, and the product is dried in a vacuum ash (5). Gas from the cold
separator is either compressed and recycled to the reactor or purged
from the unit if the design is for once-through hydrogen.
Economics:
2004 US Gulf Coast), $/bpsd 6,000
Utilitiies, typical per bbl feed:
Fuel, 10
3
Btu (absorbed) 30
Electricity, kWh 5
Steam, lb 25

Wet gas scrubbing (WGS)
Application: To reduce uid catalytic cracking unit (FCCU) particulate
(catalyst) and sulfur oxides (SO
x
) emissions to achieve compliance with
environmental regulationsgenerally NSPS (New Source Performance
Standards) and consent decrees (in the US). The technology can also be
adapted for other renery applications, e.g., coke calciners when ue
gases must be treated to reduce SO
x
and particulate emissions.
Description: The WGS process takes dirty gas from FCCUs and simul-
taneously removes particulate matter and SO
x
via direct contact with a
buffered liquid. Particulate removal is accomplished via inertial impaction
of the particulate with the scrubbing liquid. SO
2
removal is accomplished
via absorption into and reaction with the buffered scrubbing liquid. SO
3
removal is accomplished via a combination of nucleate condensation,
absorption and inertial impaction. All of this can be accomplished with
low- (3-in. of water column) or no pressure drop. This is important when
aged heat recovery systems are involved.
The liquid purge from the WGS system is further treated in either the
renery wastewater system or in a segregated system, either of which
will remove solids for landll disposal and will reduce the chemical oxy-
gen demand (COD) of the stream to meet local discharge requirements.
Operation of WGS systems demonstrates:
Flexible/forgiving performance under a wide range of FCCU op-
erations/upsets
Service factors equal to or better than FCCUs with runs exceeding
10 years
Low/zero pressure drop
Ability to meet stringent emission regulations, e.g., consent de-
cree requirements.
Performance: All WGS facilities are in compliance with their permitted
values. Compliance has been achieved for the current consent decree
particulate limits that can require emission of less than -lb of particu-
lates /1,000 lb of coke burned. They are also in compliance with consent
decree SO
2
requirements of 25 vppmd @ 0% O
2
and SO
3
consent de-
cree emission requirements of less than 10 vppmd. In addition, the WGS
has recorded run lengths in excess of 10 years without affecting FCCU
throughput.
Installation: Seventeen operating plants have over 400 years of operating
experience. Four additional units are in various stages of engineering.
Reference: 1991 AIChE Spring National Meeting, Paper No. 62c.
1990 National Petroleum Reners Association Annual Meeting, Pa-
per No. AM-90-45, March 1990.

Continued
1996 National Petroleum Reners Association Annual Meeting, Pa-
per No. AM-96-47, March 1996.
Technology owner: ExxonMobil Research and Engineering Co.
Licensor: Hamon Research-Cottrell, GN-Hamon, LLC.
Wet gas scrubbing (WGS), continued
Wet scrubbing system, EDV
Application: EDV Technology is a low pressure drop scrubbing system,
to scrub particulate matter (including PM2.5), SO
2
and SO
3
from ue
gases. It is especially well suited where the application requires high reli-
ability, exibility and the ability to operate for 4 7 years continuously
without maintenance shutdowns. The EDV technology is highly suited
for FCCU regenerator ue-gas applications.
Products: The efuents from the process will vary based on the re-
agent selected for use with the scrubber. In the case where a sodium-
based reagent is used, the product will be a solution of sodium salts.
Similarly, a magnesium-based reagent will result in magnesium salts.
A lime/limestone-based system will produce a gypsum waste. The EDV
technology can also be used with the LABSORB buffer thus making
the system regenerative. The product, in that case, would be a usable
condensed SO
2
stream.
Description: The ue gas enters the spray tower through the quench
section where it is immediately quenched to saturation temperature.
It proceeds to the absorber section for particulate and SO
2
reduction.
The spray tower is an open tower with multiple levels of BELCO-G-
Nozzles. These nonplugging and abrasion-resistant nozzles remove
particulates by impacting on the water/reagent curtains. At the same
time, these curtains also reduce SO
2
and SO
3
emissions. The BELCO-
G-Nozzles are designed not to produce mist; thus a conventional mist
eliminator is not required.
Upon leaving the absorber section, the saturated gases are direct-
ed to the EDV ltering modules to remove the ne particulates and ad-
ditional SO
3
. The ltering module is designed to cause condensation of
the saturated gas onto the ne particles and onto the acid mist, thus
allowing it to be collected by the BELCO-F-Nozzle located at the top.
To ensure droplet-free stack, the ue gas enters a droplet separa-
tor. This is an open design that contains xed-spin vanes that induce a
cyclonic ow of the gas. As the gases spiral down the droplet separa-
tor, the centrifugal forces drive any free droplets to the wall, separat-
ing them from the gas stream.
Economics: The EDV wet scrubbing system has been extremely suc-
cessful in the incineration and rening industries due to the very high
scrubbing capabilities, very reliable operation and reasonable price.
Installation: More than 200 applications worldwide on various pro-
cesses including 37 FCCU applications, 3 CDU applications and 1 uid-
ized coker application to date.
Reference: Confuorto and Weaver, Flue gas scrubbing of FCCU re-
generator ue gasperformance, reliability, and exibilitya case his-
tory, Hydrocarbon Engineering, 1999.
Continued
Eagleson and Dharia, Controlling FCCU emissions, 11th Ren-
ing Technology Meeting, HPCL, Hyderabad, 2000.
Licensor: Belco Technologies Corp.
Wet scrubbing system, EDV, continued
White oil and wax hydrotreating
Application: Process to produce white oils and waxes.
Feeds: Nonrened as well as solvent- or hydrogen-rened naphthenic or
parafnic vacuum distillates or deoiled waxes.
Products: Technical- and medical-grade white oils and waxes for plasti-
cizer, textile, cosmetic, pharmaceutical and food industries. Products are
in accordance with the US Food and Drug Administration (FDA) regula-
tions and the German Pharmacopoeia (DAB 8 and DAB 9) specications.
Description: This catalytic hydrotreating process uses two reactors. Hydro-
gen and feed are heated upstream of the rst reaction zone (containing a
special presulded NiMo/alumina catalyst) and are separated downstream
of the reactors into the main product and byproducts (hydrogen sulde
and light hydrocarbons). A stripping column permits adjusting product
specications for technical-grade white oil or feed to the second hydro-
genation stage.
When hydrotreating waxes, however, medical quality is obtained in
the one-stage process. In the second reactor, the feed is passed over a
highly active hydrogenation catalyst to achieve a very low level of aromat-
ics, especially of polynuclear compounds. This scheme permits each stage
to operate independently and to produce technical- or medical-grade
white oils separately. Yields after the rst stage range from 85% to 99%
depending on feedstock. Yields from the second hydrogenation step are
nearly 100%. When treating waxes, the yield is approximately 98%.
3
of feed:
1st stage for 2nd stage for Food-grade
techn. white oil med. white oil wax
Electricity, kWh 197 130 70
Steam, LP, kg 665 495 140
Water, cooling, m
3
48 20 7
Hydrogen, kg 10.0 2.6 1.6
Installation: Four installations use the Uhde (Edeleanu) proprietary tech-
nology, one of which has the largest capacity worldwide.
Licensor: Uhde GmbH and through sublicense agreement with BASF.
Rening Articles
C onocoPhillips S Zorb Gasoline Sulfur Removal Technology
by Jeff Vander Laan, ConocoPhillips
T he State of Liquid Redox
by Gary J. Nagl, Gas Technology Products
S uncors Optimization of a Sulfur Recovery Facility
by Dean Freeman, Suncor; Jackie Barnette and Gary Nagl, Gas Technology Products
A TCO Midstreams Gas Sweetening Experience Using Iron-Redox Technology
by Gary Gialet, Curtis Sexsmith, Rob Girard, Neil McCagherty, Neil Carnegie, Spencer Yelland, and
Dave Graubard, Gas Technology Products
S ulfur reduction: What are the options?
by C. Fredrick, Merichem Chemicals & Renery Services
P luses and minuses of caustic treating
by F. J. Suarez, Merichem Co.
[RETURN TO EQUIPMENT AND SERVICES PROVIDERS]
ARCA Regler GmbH
Kempener Strasse 18
Toenisvorst 47918
Germany
Tel: +49-(0)2156-7709-0
Fax: +49-(0)2156-770955
E-mail: sale@arca-valve.com
www.arca-valve.com
Executives:
Sales Manager (Chemical Industry) Mr. Lothar Grutesen
Sales Manager (Power Plants) Mr. Johannes Fliegen
The principle of the company is to develop, produce and sell control valves and the
corresponding pneumatic, electro-pneumatic and the recently introduced second
generation intelligent positioners.
.
[RETURN TO COMPANY EQUIPMENT & SERVICES DIRECTORY]
Axens
89, bd Franklin Roosevelt BP 50802
92508 Rueil-Malmaison Cedex
France
Tel: 33 1 47 14 21 00
Fax: 33 1 47 14 25 00
http://www.axens.net
Description: Axens is a refining, petrochemical and natural gas market focused
supplier of process technology, catalysts, adsorbents and services, backed by
nearly fifty years of commercial success. Axens is a world leader in several
areas, such as: Petroleum hydrotreating & hydroconversion, FCC gasoline
desulfurization, Catalytic Reforming, BTX (benzene, toluene, xylenes) production
& purification, Selective Hydrogenation of olefin cuts, Sulfur recovery catalysts.
Axens is a fully-owned subsidiary of IFP.
Executives: Jean Sentenac, Chairman & CEO
Jean-Pierre Franck, Chief Operating Officer
Michel Dugert, Managing Director & Process Licensing
Francis Nativel, Managing Director & Performance Programs
Christian Vaute, Managing Director & Procatalyse Catalysts and Adsorbents
Burckhardt Compression AG
IM Link 5, P.O. Box 65
Winterthur CH-8404
Switzerland
Tel: +41 (0) 52 262 55 00
Fax: +41 (0) 52 262 00 51
E-mail: info@burckhardtcompression.com
www.burckhardtcompression.com
Executives:
Vice President Marketing Peter Huber
Vice President Sales Martin Heller
Company Description:
Burckhartd Compression is a world leader in reciprocating compressor technology and
the only manufacturer of a complete series of labyrinth (Laby circle r), process gas and
hyper compressors for numerous applications. Their compressors are used in the field of
oil refining, chemical and petrochemical industries, air separation, as well as gas
transport and storage. Burckhardt Compression has a worldwide service network.
.
DMC Clad Metal Div.
Dynamic Materials Corp.
5405 Spine Road
Boulder, CO 77379
USA
Tel: 303-604-3902
Fax: 303-604-1839
E-mail: sales@dynamicmaterials.com
Website: www.dynamicmaterials.com
Executives:
Sales Jose Olivas
Sales Jim Gray
Manufacturer of DELTACLAD , explosion weld clad metal. Corrosion resistant
applications in chemical process equipment and oil refineries including: heat exchangers,
reactors, towers, separators and other vessels. Metals clad include: steel, SS, aluminum,
titanium, zirconium, nickel and copper alloys. ISO certified factories in the US and
Europe.
.
Engelhard Corporation
101 Wood Avenue
Iselin, NJ 08830
USA
Tel: 732-205-5000
Fax: 732-205-5915
E-mail: info@engelhard.com
Executives:
Barry W. Perry, Chairman & Chief Executive Officer
Victor Sprenger, Group Vice-President Process Technologies
Engelhard Corporation is a surface and materials science company that develops
technologies to improve customers products and processes. A Fortune 500 company,
Engelhard is a world-leading provider of technologies offering a comprehensive range of
FCC catalysts, environmental and performance additives for the petroleum refining
industry. For more information, visit Engelhard on the Internet at www.engelhard.com .
Emerson Process Management, Fisher Valve Division
301 S. 1
st
Ave.
Marshalltown, IA 50158
USA
Tel: 641-754-3011
http://www.fisher.com
The Fisher Valve Division of Emerson Process Management delivers time-tested and
innovative control valve solutions designed to help reduce plant maintenance costs,
reduce capital requirements, reduce the cost of regulatory compliance, and increase
process availability.
[RETURN TO COMPANY EQUIPMENT & SERVICES DIRECTORY]
Gas Technology Products LLC,
A Member of the Merichem Family of Companies
846 E. Algonquin Rd., Suite A100
Schaumburg, IL 60173
USA
Tel: 847-285-3850
Fax: 847-285-3888
http://www.gtp-merichem.com
Description: Devising a comprehensive, flexible hydrogen sulfide (H2S)
removal/recovery solution requires more than a systems, media and equipment
it requires expertise. With more than twenty-five years of experience in H2S
removal, Gas Technology Products LLC understands the needs of every
operator and every plant.
Products: Gas Technology Products provides a full line of complementary
hydrogen sulfide oxidation products: LO-CAT and LO-CAT II, Sulfur-Rite
and The EliminatorTM processes, along with its ARI-100 mercaptan oxidation
products and engineering services.
GTP offers both liquid and solid media desulfurization technologies to sweeten
gas streams and ventilation air containing virtually any levels of hydrogen sulfide
or mercaptans for systems of widely ranging capacities. For any size or type
application, GTP offers complete turnkey systems and can take total system
responsibility.
As a wholly owned subsidiary of Merichem Chemicals & Refinery Services LLC,
Gas Technology Products LLC is a part of a fully integrated organization with
unmatched technical knowledge, applications expertise, and worldwide service
coverage.
SAMSON AG Mess- und Regeltechnik
Weismllerstrae 3
Frankfurt am Main
Hessen 60314
Germany
Tel: +49 69 4009-0
Fax: +49 69 4009-1507
E-mail: samson@samson.de
www.samson.de
SAMSON produces control valves and butterfly valves in all commonly used materials
and in accordance with the DIN, ANSI, and JIS standards. The valves are suitable for use
in all areas of process engineering. SAMSON also manufactures self-operated regulators
for simple control systems. Sophisticated transmitters, controllers, and automated systems
round off our product line.
.
SNC-Lavalin GDS, Inc.
9009 West Loop South, Suite 800
Houston, TX 77096-1719
USA
Tel: 713-667-9162
Fax: 713-667-9241
E-mail: gdseng@gdseng.com
Executives:
President James M. Walters, P.E.
Vice President, Engineering Gary L. Gibson, P.E.
SNC-Lavalin GDS specializes in full service engineering, procurement and construction
management services, particularly for the petrochemical and refining industries. As part
of the SNC-Lavalin Group we are a leading engineering and construction firm in the
world. The Group has offices in 30 countries and is doing work in some 100 countries.
.
Thermo Electron Corporation
9303 W. Sam Houston Pkwy. S.
Houston, TX 77099
USA
Tel: 877-290-7422
Fax: 713-272-4573
Website: www.thermo.com
E-mail: oilandgas@thermo.com
Executives:
Director of Sales John Schwin
Director of Marketing Karen Minyard
Thermo Electron Corporation is a world leader in instrumentation. We enable our
customers to analyze, detect, measure, and control with increasingly advanced
precision. The Process Instruments Division offers a variety of gas flow computers, data
acquisition systems, liquid flowmeters, data management solutions, gas analyzers, level
sensors, and much more to the petroleum industry.
.
UOP LLC
25 E. Algonquin Ave.
Des Plaines, IL 60017-5017
USA
847 391 2000
847 391 2253 (fax)
www.uop.com <http://www.uop.com/>
UOP LLC is a leading international supplier and licensor of process technology,
catalysts, adsorbents, process plants, equipment and consulting services to the petroleum
refining, petrochemical, and gas processing industries. UOP's expertise extends from
R&D to the manufacture and sale of adsorbents, catalysts, and specialty chemicals. We
focus on delivering solutions to improve our customers' competitiveness.
President & CEO: Carlos Guimaraes
US Filter
301 West Military Road
Rothschild, WI 54474
USA
Tel: 713-359-7211
Fax: 713-355-3219
E-mail: hpi@usfilter.com
www.usfilter.com
US Filter provides total water management for all waters used by, generated by or
emanating from the petroleum and petrochemical industries. Whether upstream or
downstream, no matter what the application or its global location, US Filter has the
expertise needed to resolve your water issues.
.
KBC Advanced Technologies, Inc.
14701 Saint Marys Lane, Suite 300
Houston, TX 77079 USA
Tel: 281-293-8200
Fax: 281-293-8290
Web: www.kbcat.com
E-mail: kbc@kbcat.com
KBC Advanced Technologies is a leading independent consulting and services group, delivering
improvements in business performance and asset value to owners and operators in the oil
refining, petrochemical and processing industries worldwide. KBC analyses plant operations and
business processes, and recommends changes that deliver material and measurable
improvements in profitability.
Executives:
Peter J. Close, Chief Executive Officer
Nicholas J. Stone, Finance Director
W. George Bright, Chief Operating Officer
Axens Axens is a rening, petrochemical and
natural gas market focused supplier of process tech-
nology, catalysts, adsorbents and services, backed
by nearly 50 years of commercial success. Axens is a
world leader in several areas, such as:
Petroleum hydrotreating & hydroconversion
FCC gasoline desulfurization
Catalytic Reforming
BTX (benzene, toluene, xylenes) production &
purication
Selective Hydrogenation of olen cuts
Sulfur recovery catalysts.
Axens is a fully-owned subsidiary of IFP.
Benzene reduction
Catalytic reforming
Diesel hydrotreating
Ethers
Hydrocracking
Hydrocracking/hydrotreatingVGO/DAO
Hydrotreatingresid
Isomerization
Lube oil rening, spent
3
C
4
cuts
Spent oil lube re-rening
Processes
Technology Solutions, a division of ConocoPhillips,
is a premier provider of technology solutions for the
vehicles of today and the oilelds and energy sys-
tems of tomorrow. Backed by modern research fa-
cilities and a strong tradition of innovation, we de-
velop technologies that help oil and gas producers,
reners, and manufacturers reach their objectives
through the development and implementation of
leading-edge technologies. From enhanced produc-
tion methods, to gasoline sulfur removal processes,
to valuable catalysts that enhance fuel cell opera-
tion, Technology Solutions prepares producers, re-
ners, and consumers alike for a cleaner, more ben-
ecial future.
C onocoPhillips S Zorb Gasoline Sulfur Removal
Technology
by Jeff Vander Laan, ConocoPhillips
Alkylation
Coking
Isomerization
Articles
Processes
Devising a comprehensive, exible hydrogen sul-
de (H
2
S) removal/recovery solution requires more
than systems, media and equipment it requires
expertise. With more than twenty-ve years of ex-
perience in H
2
S removal, Gas Technology Products
LLC understands the needs of every operator and
every plant.
Gas Technology Products provides a full line of
complementary hydrogen sulde oxidation prod-
ucts: LO-CAT and LO-CAT II, Sulfur-Rite and
The EliminatorTM processes, along with its ARI-
100 mercaptan oxidation products and engineer-
ing services.
GTP offers both liquid and solid media
desulfurization technologies to sweeten gas streams
and ventilation air containing virtually any levels
of hydrogen sulde or mercaptans for systems of
widely ranging capacities. For any size or type ap-
plication, GTP offers complete turnkey systems and
can take total system responsibility.
As a wholly owned subsidiary of Merichem Chemi-
cals & Renery Services LLC, Gas Technology Prod-
ucts LLC is a part of a fully integrated organization
with unmatched technical knowledge, applications
expertise, and worldwide service coverage.
T he State of Liquid Redox
by Gary J. Nagl, Gas Technology Products
S uncors Optimization of a Sulfur Recovery Facility
by Dean Freeman, Suncor; Jackie Barnette and Gary Nagl, Gas
Technology Products
A TCO Midstreams Gas Sweetening Experience
Using Iron-Redox Technology
by Gary Gialet, Curtis Sexsmith, Rob Girard, Neil McCagherty,
Neil Carnegie, Spencer Yelland, and Dave Graubard,
Gas Technology Products
H
2
S removal (LO-CAT)
H
2
S removal (Sulfur-Rite)
Articles
Processes
A leader in processing renery spent caustic
streams at its USA processing plants for chemicals re-
covery for over 50 years, Merichem Company has
more recently been recognized worldwide for its ex-
pertise and technology for processing spent caustics
within the renery.
Over 25 years experience licensing more than 450 hydrocarbon
caustic and other aqueous phase treating sytems worldwide.
Over 150 hydrocarbon treating systems have been modularly
designed and built at our Houston, Texas detailed engineering
and fabrication facility.
Our FIBER-FILM non-dispersive mass transfer technology has
been licensed and chosen by more than 75% of worldwide
reneries that have added caustic treating systems during the
last ten years.
Full-service engineering and fabrication services from Houston
as well as abroad.
Each unit is custom-designed to the clients specications and
standards.
ISO 9001/Q9001 Certied since 1994.
39 international ofces representing Merichem in 54 countries
are in constant contact with regional renery and petrochem-
ical businesses.
Superior technical service support.
Expertise in all aspects of plant efuent caustic management.
Since 1974, Merichems Process Technology Division has been
providing technologies to the hydrocarbon process industry.
One of the most widely applied technologies employs the FI-
BER-FILM Contactor, which is a mass transfer device consisting
of a retaining cylinder packed with very ne, proprietary bers.
This revolutionary system virtually eliminates the problems as-
sociated with conventional dispersive mass transfer methods.
S ulfur reduction: What are the options?
by C. Fredrick, Merichem Chemicals & Renery Services
P luses and minuses of caustic treating
by F. J. Suarez, Merichem Co.
H2S removal (LO-CAT)
H2S removal (Sulfur-Rite)
Treatinggases
Treatinggasoline
Treatinggasoline and light hydrocarbon liquids
Treatinggasoline desulfurization, ultra deep
Treatingspent caustic deep neutralization
Treatingsweetening
Articles
Processes
1
ConocoPhillips S Zorb Gasoline Sulfur Removal Technology:
Unique Chemistry, Proven Performance, and Optimized Design
By
Jeff Vander Laan
Technology Product Director
ConocoPhillips
Introduction
ConocoPhillips Company breakthrough technology, S Zorb Sulfur Removal
Technology (SRT), substantially lowers the sulfur concentration in FCC gasoline
while still protecting octane-rich olefins and aromatics. In the S Zorb process
sulfur-containing molecules react with the novel S Zorb sorbent that retains the
sulfur atom from the molecule while the hydrocarbon portion of the molecule is
released back into the process stream. This unique reaction pathway does not
generate free H
2
S; therefore, preventing recombination of hydrogen sulfide and
olefins to form mercaptans. This technology was first demonstrated at the
ConocoPhillips refinery in Borger, Texas, USA in April 2001 and a second
commercial unit began operation in November 2003 and ConocoPhillips refinery
in Ferndale, Washington, USA.
Recent work conducted as part of a process optimization study led
ConocoPhillips to further optimize the S Zorb process resulting in a reduction of
capital and operational costs. In addition, this work led to the discovery of an
interesting S Zorb phenomenon. Pilot plant studies showed that olefin
conversion, hydrogen consumption and octane loss all decrease with increasing
reactor temperature while selectivity for sulfur removal increases. Subsequent
testing in the Borger unit confirmed these results on a commercial scale. The
resulting process enhancements are incorporated into an optimized design for
the unit that is being built at the ConocoPhillips Lake Charles Refinery, located in
Westlake, Louisiana, USA as well as a 4
th
ConocoPhillips unit that is in the
advanced stages of project approval. This paper will focus on the optimized
design, improved sulfur selectivity, additional enhancements to the technology,
and operational details from the two commercial S Zorb units.
Overview of S Zorb Sulfur Removal Chemistry
The ConocoPhillips S Zorb SRT is an advanced processing technology for
extracting sulfur atoms from gasoline blend stocks. It is not a
hydrodesulfurization technology. Rather, it uses a novel sorbent that specifically
absorbs sulfur-containing molecules and removes the sulfur atom from the
molecule. The sulfur atom is retained on the sorbent while the hydrocarbon
portion of the molecule is released back into the process stream. This unique
reaction pathway does not generate free H
2
S, and, therefore avoids problems
associated with H
2
S inhibition and mercaptan recombination. Figure 1 compares
S Zorb SRT chemistry with hydrotreating.
RETURN TO ARTICLE MENU
2
Figure 1: S Zorb vs. Hydrotreating
The S Zorb chemistry leaves the hydrocarbon stream virtually unchanged except
for the removal of sulfur. Hence the ConocoPhillips S Zorb SRT process can
economically reduce the sulfur content of gasoline to less than 10 ppm with
minimal octane loss, minimal hydrogen consumption and near zero volume loss.
Hydrogen consumption is kept low by minimizing the extent of olefin saturation.
Another interesting aspect of the S Zorb chemistry is the order of sulfur reactivity.
Figure 2 shows a comparison of the reaction rates for different species of sulfur
compounds that are typically found in cracked naphthas. This figure does not
compare the rates on an absolute basis, but rather on a relative basis where the
first-order rate of sulfur removal has been normalized relative to thiophene. On
an absolute basis, the sulfur removal rates observed with S Zorb SRT are
several times faster than those reported for HDS. As the figure illustrates,
thiophene is the hardest molecule to remove for either process; however, there is
an enhancement in activity for alkylated thiophenes, alkylated benzothiophene,
and benzothiophene for the S Zorb sorbent. As a result, S Zorb SRT offers much
more flexibility and forgiveness with regard to gasoline endpoint changes and
other operational upsets which may lead to significant variations in the feed sulfur
speciation.
3
Figure 2. Comparison of relative reaction rates for different sulfur
compounds. The HDS data were taken from Hatanaka et al. (1).
The ability to retain high sulfur conversion while minimizing olefin hydrogenation
and the subsequent octane loss presents a significant advantage of S Zorb SRT
over hydrotreating technologies, as shown in Figure 3. (HDS data are from
McGuff (2) and S Zorb SRT data are from the Borger, Texas commercial unit.)
Relative
Reactivity for S Zorb SRT
1.0
2.1
3.7
4.0
7.0
10.0
1
10
Thiophene C1-C2
Thiophenes
C3+ Thiophenes Alkyl-
Benzothiophenes
Benzothiophene Mercaptans
& Sulfides
Relative
Reactivity for HDS
1.0 1.0
0.3
2.0
5.5 5.5
1
10
Thiophene C1-C2
Thiophenes
Benzothiophenes
& Sulfides
Relative
Reactivity for S Zorb SRT
1.0
2.1
3.7
4.0
7.0
10.0
1
10
Thiophene C1-C2
Thiophenes
Benzothiophenes
& Sulfides
Relative
Reactivity for HDS
1.0 1.0
0.3
2.0
5.5 5.5
1
10
Thiophene C1-C2
Thiophenes
Benzothiophenes
& Sulfides
4
Figure 3. Olefin Retention Comparisons
0
20
40
60
80
100
80 85 90 95 100
Sulfur Conversion, %
O
l
e
f
i
n

C
o
n
v
e
r
s
i
o
n
,

%
Conventional fixed bed Selective HDS
Selective HDS S Zorb SRT
Octane loss at a specified sulfur conversion is determined by the type of olefins
saturated, not just by the total olefin conversion. As sulfur conversion
requirements increase, the more severe operating conditions required will cause
octane loss to increase. This is true of all technologies, but less so for the S Zorb
process. Data compiled throughout the development of S Zorb SRT and from
commercial experience demonstrate the high selectivity of the S Zorb
technology, which results in superior octane retention capabilities.
A recently completed optimization study resulted in the discovery of an
interesting S Zorb phenomenon, which does not occur in hydrotreating. S Zorb
pilot plant work showed that olefin conversion, hydrogen consumption, and
octane loss all decrease with increasing reactor temperature. Figure 4 shows the
decrease in olefins conversion with temperature observed in pilot plant
operations and confirmed through commercial operations at the first S Zorb unit
located in Borger, TX. Figure 5 shows the temperature effect on RON and MON
observed in commercial trials.
5
Figure 4: Temperature Effect - Olefin Conversion
Figure 5: Temperature Effect - RON & MON
Temperature Temperature
O
c
t
a
n
e

L
o
s
s

RON Loss
MON Loss
RON Loss
MON Loss
RON Loss
MON Loss
Commercial Unit
Figure 6 summarizes the effect of temperature on octane loss for various types of
feeds with varying levels of feed sulfur. In all cases there was a significant
reduction in octane loss with the higher reactor temperature and a very slight
increase in light ends formation (less than 0.2 wt%).
Olefin Conversion with Temperature
O
l
e
f
i
n

C
o
n
v
e
r
s
i
o
n
Temperature Temperature
Pilot Plant
Commercial Unit
6
Figure 6: Temperature Effect Feed Variation
Process Description, Revamp Options, and Flexibility
Process Description
To take advantage of the unique selectivity for sulfur removal at low levels of
olefin hydrogenation, the S Zorb process was designed using a fluidized bed
reactor with continuous regeneration to control the steady-state level of sulfur on
the sorbent in the reactor. The use of a continuously regenerated, fluid bed
reactor system means that an S Zorb unit achieves true steady state operation,
with no degradation in performance throughout the run.
Gasoline feed is combined with a hydrogen stream that is vaporized in the
charge heater and injected into the bottom of the fluidized bed reactor. As the
vaporized feed stream moves through the bed, the sorbent removes sulfur
compounds from the hydrocarbon vapor. The sulfur-free hydrocarbon portion of
the molecule stays in the process stream. The sulfur atom remains with the
sorbent, which is transported to the regenerator. In the regenerator, sorbent is
oxidized to produce sulfur dioxide (SO
2
). The regenerator effluent is treated and
then recycled back to the regenerator. The regenerated sorbent is transferred to
a reducing vessel before being returned to the reactor. A general overview of
the S Zorb process is illustrated in Figure 7.
Feed 2
915 ppm S
Feed 3
1300 ppm S
Feed 4
1990 ppm S
Feed 1
735 ppm S
HCN of
Feed 1
1000 ppm S
O
c
t
a
n
e

L
o
s
s

Base Temperature
Higher Temperature
Feed 2
915 ppm S
Feed 3
1300 ppm S
Feed 4
1990 ppm S
Feed 1
735 ppm S
HCN of
Feed 1
1000 ppm S
O
c
t
a
n
e

L
o
s
s

Base Temperature
Higher Temperature
Base Temperature
Higher Temperature
!Pilot Plant Runs at Similar Sulfur Conversion Levels
7
Figure 7: S Zorb SRT Process Overview
Revamp Options
Refiners evaluating revamp options should give serious considerations to S Zorb
SRT. A review of the S Zorb flow sheet Figure 7 shows that, outside of the
reactor-regenerator section shown within the dashed lines, the process looks
similar to a conventional hydrotreater. Existing hydrotreaters can be converted to
use S Zorb technology, usually with higher throughput. The recycle hydrogen gas
rates used for the S Zorb process are much lower than those typically used for
hydrodesulfurization, which results in additional hydraulic capacity that can be
used for incremental liquid feed. Existing hydrotreater equipment can be easily
revamped for use with S Zorb SRT. The S Zorb process also has the unique
ability to optimize octane retention capabilities across a fairly wide range of
reactor pressures making it a good fit for many revamp scenarios where the
operating pressure is set by existing equipment. As a result of this unique
flexibility, there are many cases where a revamp using S Zorb SRT will be able to
use existing compression, heat exchange, and separation equipment without the
extensive modifications that would be required for a comparable HDS revamp. Of
course, the refiner will also benefit from all the operating advantages and
superior operating performance inherent in S Zorb SRT. If a refiner has already
installed a gasoline desulfurization technology that cannot economically meet the
existing and future limits, replacing the reactor with an S Zorb reactor system is a
viable option.
8
Flexibility
The S Zorb fluidized bed reactor holds an even temperature distribution and
maintains start of run activity throughout the run cycle. Because sorbent is
continually regenerated, there is no measurable coke build up through the run
cycle. Reactor fouling due to diolefin or other contaminants is not a problem for S
Zorb SRT. The S Zorb sorbent has proven to be remarkably tolerant to
contaminants and poisons found in fluidized catalytic cracker (FCC) and coker
naphthas. For example, S Zorb SRT has demonstrated the ability to handle
typical silicon levels found in most coker naphthas with no loss in performance.
During silicon upsets, full activity can be restored either via the natural
replacement of sorbent due to slow attrition or by employing a controlled addition
and withdrawal strategy. In this manner, the S Zorb process design gives refiners
a number of options to insure that optimum sulfur removal activity is maintained,
offering an unprecedented level of flexibility.
It is a well-known fact that nitrogen compounds are poisonous to hydrotreating
catalysts. Refiners who routinely process crude oils that are high in nitrogen
content are well acquainted with the challenges associated with desulfurization of
distillate, naphtha, and other feedstocks using current hydrotreating technologies.
In contrast to hydrotreating, S Zorb pilot plant experiments conducted with FCC
naphtha feeds high in total and basic nitrogen have shown no negative effect on
sulfur removal activity, octane retention, run length, or sorbent requirements. This
is just one more example of how the unique S Zorb chemistry produces a very
robust and flexible desulfurization process.
In addition, the unit is easily adjusted for feed changes and hydrogen purity has
little effect on unit performance. In S Zorb SRT units these features combine to
give stable yet flexible operations and run lengths for gasoline units that can
easily match an FCC unit. Matching the run lengths of the S Zorb unit and the
FCC unit provides refiners with an economic advantage, eliminating the need for
additional tankage to store untreated FCC gasoline during sulfur treatment unit
downtime.
Commercial Experience
Borger Refinery S Zorb Unit
The first commercial installation of S Zorb Sulfur Removal Technology has been
in service at ConocoPhillips refinery in Borger, Texas, USA since April 2001.
The unit was designed to process full range debutanized FCC naphtha with feed
sulfur content up to 1000 ppmw. The unit has very successfully demonstrated
the impressive capabilities of this technology and confirmed our ability to scale
up pilot plant results to a commercial scale. Table 1 shows a side by side
comparison of typical results from the Borger S Zorb unit vs the pilot plant. This
is just one of many examples of how the Borger unit exceeded ConocoPhillips
performance expectations. During the last 3 _ years of operation, this unit has
shown the ability to effectively remove sulfur from feeds ranging from 200 to
9
1400 ppmw and produce product with less than 10 ppmw sulfur. This unit has
demonstrated that S Zorb SRT is a proven, reliable, and flexible process for FCC
Naphtha desulfurization.
Table 1 Comparison of typical performance of the Borger S Zorb unit vs
pilot plant results with Borger feed
Borger S Zorb Unit Pilot Plant
Feed sulfur, ppmw 248 218
Product sulfur, ppmw 14 14
Sulfur Conversion 94.4% 93.6%
Octane Loss, !(R+M)/2 +0.1 -0.1
Charge Rate, mtpd 750 0.14
Reactor Temperature, C 400 413
Reactor Pressure, kb/cm
2
g 9.3 10.6
WHSV, hr
-1
8.0 6.0
Ferndale Refinery S Zorb unit
The largest commercial S Zorb SRT unit was brought on stream in the fourth
quarter of 2003 at ConocoPhillips refinery in Ferndale, Washington, USA. The S
Zorb unit was part of a refinery upgrade project that included the start up of a
new fluidized catalytic cracking unit in the first quarter of 2003. The Ferndale
refinery has a crude oil processing capacity of 95,000 bpd. The S Zorb unit at
Ferndale has a design capacity of 20,000 bpd. It is designed to reduce the sulfur
in a debutanized full range FCC gasoline stream from about 1,500 ppmw down to
10 ppmw.
The Ferndale S Zorb SRT unit was designed and constructed in 17 months and
has proven capable of running at its design capacity and meeting product
specifications. The startup of the S Zorb unit at Ferndale took place in November
of 2003 and was completed successfully and safely. The unit was commissioned
ahead of schedule and came in 10% under budget. Gasoline from the FCC
debutanizer bottoms was introduced to the S Zorb unit on November 15, 2003.
Within 24 hours, the unit was running at design capacity. Sorbent regeneration
began about 48 hours after gasoline was introduced into the unit. In less than 72
hours, the S Zorb unit was stable at steady state conditions.
10
Soon after the initial startup, the Ferndale S Zorb unit began to achieve a high
degree of sulfur removal. Sulfur levels of less than 10 ppmw were observed with
minimal octane loss. Figure 8 is a plot of octane loss versus sulfur conversion
obtained during the first several months of operation. The data show the
excellent capabilities of the S Zorb unit at Ferndale and confirm the ability of S
Zorb SRT to achieve low product sulfur levels and minimum octane loss even at
high sulfur conversions.
Figure 8. Gasoline sulfur conversion and corresponding octane loss
observed at the S Zorb SRT unit at Ferndale refinery
-3.0
-2.5
-2.0
-1.5
-1.0
-0.5
0.0
0.5
1.0
94% 95% 96% 97% 98% 99% 100%
% Desulfurization
O
c
t
a
n
e

L
o
s
s

(
P
r
o
d
u
c
t

-

F
e
e
d
)
Delta RON
Delta MON
Delta Road
S Zorb Process Optimization
Recognizing the importance of continuous improvement, ConocoPhillips
conducted a Process Optimization Study for the S Zorb process. The study was
based on the lessons learned from more than two years of the Borger S Zorb unit
operating experience and the improved process conditions demonstrated in our
pilot plants. Over 150 value-engineering ideas were systematically evaluated,
validated, and, if approved, incorporated into the optimized design.
The objectives for the process optimization work included fine-tuning the basic
technology, reducing the ISBL cost by at least 20%, and matching or exceeding
the reliability, measured as onstream availability, of a fixed-bed
hydrodesulfurization process. Figure 9 depicts the flow scheme of reactor,
regeneration, and sorbent transfer sections of the optimized design.
11
Figure 9: S Zorb Optimized Flow Scheme
Reactor Section
The most significant change in the reactor section was an increase in reactor
pressure. The increase in pressure increases gas residence time in the reactor,
allowing a decrease in reactor sorbent inventory and a decrease in the molar
ratio of hydrogen to hydrocarbon. Higher reactor pressure also increases sorbent
efficiency, which allows an increase in sulfur on sorbent load. The lower gas
volume allows the use of a reciprocating compressor or the possibility for the
refiner to select a once-through hydrogen option. Also, lower gas volumes result
in a reduction of the reactor filter cost. The lower sorbent circulation rate required
as a result of the higher level of sulfur retained on sorbent allows a reduction in
the size of equipment and piping.
Regeneration Section
Better understanding of sorbent regeneration chemistry combined with over two
years of commercial operating experience has enabled optimization of
regenerator operating conditions. The major change is the use of once-through
air regeneration, as opposed to a recycle nitrogen system with makeup air. This
change eliminated the regeneration recycle gas compressor, and the lower gas
volume allows use of a smaller air compressor. The lower gas volume also
reduces the size of both the SO
2
treatment package and the regenerator system
equipment sizes including vessels, piping, and valves. In addition, the
regenerator temperature has been lowered to allow the use of preferred vessel
metallurgy. The lower regenerator temperature shows no apparent effect on
either sulfur removal activity or octane loss.
12
Solids Transfer Section
The solids transfer system, which moves sorbent to and from the reactor and
regenerator systems, has been simplified. The use of one lockhopper system, as
opposed to two-lockhopper operation, has resulted in lower capital requirements
and operating costs (lower nitrogen and hydrogen requirements) without
compromising operability, reliability, or safety. HAZOP reviews have been
conducted to assure the safe operation of the One-Lockhopper System. The
results of the HAZOPs did not show any safety issues associated with the
design.
Reliability
The S Zorb process has the ability to shutdown and isolate the sorbent
regeneration system long enough to perform typical maintenance tasks. This
allows the reactor system to stay online at full charge making low sulfur product.
One objective of the Process Optimization Study was to ensure that the
optimized design matched or exceeded current reliabilities. The Process
Optimization team examined each section of the S Zorb process and made
recommendations to further improve unit reliability. In parallel with the Process
Optimization Study, KBC Advanced Technologies Inc. was requested to perform
an independent reliability assessment for the optimized design. In particular,
KBC was asked to compare S Zorb SRT reliability with hydrodesulfurization
reliability. KBC used their own methodology, equipment reliability database, and
set all the reliability assumptions. They concluded that there was no significant
difference in reliability between S Zorb SRT and hydrodesulfurization.
Conclusions and Future Outlook
The Ferndale units safe and successful start-up and reliable performance
demonstrate the advantages of S Zorb SRT for desulfurization of gasoline
streams. The demonstrated commercial success at Ferndale is complemented
by further reductions in capital and operating costs and improvements in the
technologys performance and reliability. A 38,500 bpd S Zorb unit featuring
these technical improvements is in the advanced stages of design/construction
for the ConocoPhillips refinery at Lake Charles, Louisiana. The combined feed
sulfur level is approximately 1,000 ppm and the unit is being designed to produce
a 10 ppm product. Startup of the S Zorb unit at Lake Charles is scheduled for late
2005. In addition, a 4
th
ConocoPhillips S Zorb unit is in the advanced stages of
project definition and approval. The anticipated design throughput is around
30,000 BPD and is targeted to start-up in late 2006.
The future promises to bring continued downward pressure on the sulfur content
of gasoline even beyond the near term targets that have been established in
many countries around the world. S Zorb technology is strongly positioned to
produce fuels that comply with much more stringent sulfur regulations with little,
13
or potentially no, octane loss, minimal hydrogen consumption, strong operating
reliability, and flexibility.
ConocoPhillips is committed to an active technology development program
focused on additional enhancements to S Zorb SRT. These enhancements
promise to deliver additional improvement to the technology, including further
improvements to the impressive octane retention capability. These
enhancements are expected to be available near term and are considered drop-
in improvements. So, the benefits are immediate requiring little or no capital to
implement.
References
1) S. Hatanaka, M. Yamada, and O. Sadakane, Hydrodesulfurization of
Catalytic Cracked Gasoline. 1. Inhibiting Effects of Olefins on HDS of
Alkyl(benzo)thiophenes Contained in Catalytic Cracked Gasoline, Ind.
Eng. Chem. Res., 1997, 36, 1519-1523.
2) Tim McGuff, Ultra Low Sulfur Gasoline via Catalytic Distillation, CD
Tech, GDS Seminar, July 18, 2001, Houston.
The State of Liquid Redox
By Gary J . Nagl
Gas Technology Products
846 E. Algonquin Road, Suite A100
Schaumburg, IL 60173 USA
Abstract
As early as the beginning of the century, work has been ongoing to develop a liquid
phase, regenerative process for converting hydrogen sulfide (H
2
S) into pure,
elemental sulfur. This work has lead to the introduction of over 25 different processes,
most of which with very little commercial success. However, in the late 1940s, the
North Western Gas Board and the Clayton Aniline Company developed the Stretford
Process, which utilized an aqueous solution of vanadium and anthraquinone (ADA).
Although the Stretford process had some serious process, operational and
environmental problems, the process filled a much-needed niche and became fairly
popular throughout the 50s, 60s and 70s.
In the late 1960s the CIP process, which employed an aqueous solution of chelated
iron, was introduced in the United Kingdom. The process failed miserably; however,
its failure did lead to the successful introduction of the LO-CAT
Process in the late

1970s, which solved many of the problems encountered with the CIP Process and
the Stretford Process. In the late 1980s, another chelated iron process, the Sulferox
Process, was introduced; however, the developers of the LO-CAT and Sulferox
processes have recently combined efforts to improve liquid redox processing even
further.
Throughout the last half of the century, liquid phase oxidation has played an
important role in the recovery of sulfur from various sources of hydrogen sulfide. Of
all the processes available for converting H
2
S to sulfur, current liquid phase oxidation
systems are the most versatile. They are able to treat any type of gas stream containing
H
2
S, at a wide variety of operating conditions and all at removal efficiencies
exceeding 99%. This paper will discuss the major liquid oxidation processes,
describing in detail their advantages and disadvantages. In addition, the current R&D
efforts in the field of liquid phase oxidation will be discussed with a glance of what
future developments may occur.
Keywords: Desulfurization, sulfur recovery, liquid redox, chelated iron, LO-CAT
Introduction
Liquid phase oxidation processes for the removal of hydrogen sulfide (H
2
S) from gas
streams were initially developed to correct certain problems associated with dry
oxidation processes such as iron sponge. The problems being mainly large plot
requirements, replacement of the oxidation media on a frequent basis, and safety
problems. This development work led to the utilization of various oxygen carriers
dissolved or suspended in a liquid phase, which could be regenerated continuously at
ambient temperatures.
Most early development work was done for systems processing coal gas or town gas
with the objective of removing both hydrogen sulfide and ammonia by the formation
of ammonium sulfate and elemental sulfur. Some of these early processes included the
Feld Process, the Gluud Process, and the Koppers C.A.S. Process all of which
employed polythionate solutions. Because of the complex chemistry, none of these
processes achieved any commercial success.
After the failure of the polythionate processes, development shifted towards utilizing
suspensions of iron oxide in aqueous solutions, which in essence was an attempt at a
continuous iron sponge process. The hydrogen sulfide reacts with an alkaline
compound to form hydrosulfide, which reacts with iron oxide to form iron sulfide,
which in turn reacts with oxygen to form iron oxide and sulfur. Development work in
this area lead to the introduction of the Burkheiser, Ferrox and Manchester processes.
During the 1920s the Thylox and Giammarco-Vetrocoke processes met with some
commercial success. However, both of these processes employed thioarsenate
solutions, which resulted in toxicity problems caused by the arsenic.
Another group of processes which showed technical promise but were limited by
toxicity problems were those employing iron cyanide solutions. The Fischer Process
and the Autopurification process are examples. These processes employed ferric and
ferrocyanide complexes as oxidizing agents.
A summary of the various liquid phase oxidation processes, which have been
developed throughout the years, is contained in Table I.
The Stretford Process
The first liquid phase, oxidation process, which gained widespread commercial
acceptance, was the Stretford process. The process was developed by the North
Western Gas Board and the Clayton Aniline Company in England to remove H
2
S
from town gas. The original process utilized an aqueous solution of
carbonate/bicarbonate and anthraquinone disulfonic acid (ADA). However, the
process suffered from several inherent problems. The solution had a very low
capacity for dissolved sulfides resulting in large liquid circulation rates and hence,
high power consumption. In addition, the sulfur formation reaction was very slow
requiring large liquid inventories and resulting in high byproduct formation
(thiosulfates).
These problems were corrected to a certain extent by the addition of alkali vanadates
to the solution, which, in essence, replaced dissolved oxygen as the oxidant in the
conversion of hydrosulfide ions (HS
-
) to elemental sulfur. In the reaction the
vanadium ions undergo a valance change from
+
5 to
+
4. To reoxidize the Va
+4
ions
back to the
+
5 State, ADA is added as an oxygen carrier, and the ADA is
subsequently regenerated with air. The process chemistry can be summarized as
follows;
A typical flow diagram of a Stretford unit is illustrated in Fig. 1.
Although the addition of vanadium to the Stretford Process increases the reaction rate
of hydrosulfide ions to sulfur sufficiently to make the process commercial, it still
produces a significant amount of byproduct thiosulfate. The reaction is still slow
enough that air streams cannot be treated due to the high rate of thiosulfate formation.
Hundreds of Stretford units have been installed throughout the world; however, their
popularity vanished in the mid 1980s after the introduction of the chelated iron
processes which addressed many of the deficiencies of the Stretford process
Chelated Iron-Based, Liquid Redox Processes
Iron is an excellent oxidizing agent for the conversion of H
2
S to elemental sulfur;
however, due to the very low solubility of iron in aqueous solutions, the iron had to
be present in the dry state (iron sponge) or in suspensions (the Ferrox process) or
compounded with toxic materials such as cyanides. In the 1960?s development work
was begun in England to increase the solubility of elemental iron in aqueous
solutions. This work led to the introduction of the CIP process, CIP being an acronym
for "Chelated Iron Process".
In this process, iron, in its ferric state (
+
3), is held in solution by a chelating agent,
namely ethylenediaminetetraacetic acid (EDTA). The intent of the process was to
oxidize sulfide (S
=
) and hydrosulfide (HS
-
) ions to elemental sulfur by the reduction
of the ferric (Fe
+3
) iron to ferrous (Fe
+2
) iron, and the subsequent reoxidation of the
ferrous ions to ferric ions by contact with air. The chemistry of all chelated iron
processes is summarized as follows with (l) and (v) representing the liquid and vapor
states, respectively;
Equations 1 and 2 represents the absorption of H
2
S into the aqueous, chelated iron
solution and its subsequent ionization, while equation 3 represents the oxidation of
sulfide ions to elemental sulfur and the accompanying reduction of the ferric iron to
the ferrous state. Equations 4 and 5 represents the absorption of oxygen into the
aqueous solution followed by oxidation of the ferrous iron back to the ferric state.
Equations 3 and 5 are very rapid. This is in contrast to the oxidation reactions in the
Stretford process when using vanadium. Consequently, iron-based systems generally
produce relatively small amounts of byproduct thiosulfate ions, and in properly
designed units, air streams can actually be processed. However, as in the Stretford
process, equations 1 and 4 are relatively slow and are the rate controlling steps in all
chelated iron processes.
It is interesting to note that the chelating agents do not appear in the process
chemistry, and in the overall chemical reaction, the iron cancels out. So the obvious
question is why is chelated iron required at all, if it doesnt part take in the overall
reaction. The iron serves two purposes in the process chemistry. First, it serves as an
electron donor and acceptor or in other words, a reagent. Secondly, it serves as a
catalyst in accelerating the overall reaction. Because of this dual purpose, the iron is
often called a "catalytic reagent". The chelating agent(s) do not part take at all in the
process chemistry. All the chelating agents do is to increase the solubility of iron in
water, thus reducing the circulation rates required to furnish the two moles of iron
required in equation 3.
Although it appears that chelated iron would solve many problems associated with
previous liquid oxidation processes, the CIP Process failed miserably. In very short
order after starting up, all of the iron precipitated out of solution as iron sulfide, FeS.
The problem was that the chelation strength of many chelating agents varies
considerably with solution pH, and unfortunately, the pHs experienced in the CIP
process were outside the range of EDTA.
In the early 1970s, a small company in the Chicago area (ARI Technologies) started
development work on a process, which employed multiple chelating agents. The idea
being that by employing chelating agents with overlapping pH ranges where the
chelation strengths were high, the iron would stay in solution at all times. This
development work led to the introduction of the LO-CAT
process in the late 1970s.

The process worked well for units processing small quantities of H
2
S; however, in
the first unit processing tons per day of sulfur, the process, in essence, failed. It was
found that the chelating agents were disappearing very rapidly requiring extremely
high chemical makeup rates.
Research found that the chelating agents were being oxidized to useless byproducts
by a free radical mechanism. After a few years of experimentation, the chelate
oxidation rate was reduced to an acceptable level by the introduction of free radical
scavengers and by switching to chelating agents, which were much more resistant to
oxidation.
Iron-based, liquid oxidation has developed into a very versatile processing scheme for
treating gas streams containing moderate amounts of H
2
S. Advantages of these
systems include the ability to treat both aerobic and non-aerobic gas streams, removal
efficiencies in excess of 99.9%, essentially 100% turndown on H
2
S concentration and
quantity, and the production of innocuous products and byproducts.
The three most common processing schemes encountered in iron-based, liquid
oxidation systems are illustrated in Fig. 2 through 4. Fig. 2 shows a "Conventional"
unit, which is employed for processing gas streams, which are either combustible or
cannot be contaminated with air such as carbon dioxide, which is being treated for
beverage purposes. In this scheme, equations 1 through 3 are performed in the
Absorber while equations 4 and 5 are performed in the oxidizer. Fig. 3 illustrates an
"Autocirculation" unit, which is used for processing acid gas (CO
2
and H
2
S) streams
or for other non-combustible streams, which can be contaminated with air. In this
scheme, equations 1 through 3 are performed in the "Centerwell" which is nothing
more than a piece of pipe open on each end. The purpose of the centerwell is to
separate the sulfide ions. from the air to minimize byproduct formation. The volume
within the centerwell is essentially the same as the absorber in a conventional unit.
The other unique feature of the Autocirculation scheme is that no pumps are required
to circulate solution between the centerwell (absorber) and the oxidizer. In these units
there is a larger volume of air than acid gas; consequently, the aerated density on the
outside of the centerwell is less than on the inside resulting in a natural circulation
from the oxidizer into the centerwell.
The last type of processing scheme (Fig. 4) is the aerobic unit (air contaminated with
H
2
S) in which equations 1 through 5 all occur within the same vessel, at the same
time and without separation of the absorber and the oxidizer. These are generally less
expensive units than the other two schemes; however, because there is always oxygen
in the presence of sulfide ions, consequently, these units produce the most
byproducts.
The Present
Although references are continuously made that iron-based, liquid redox systems are
plagued with plugging and foaming problems and that the process cannot be operated
at high pressure due to pump and foaming problems, these problems for the most part
have been solved for some time.
Foaming occurrences are either a start-up phenomenon or the result of large amounts
of liquid hydrocarbons entering the unit. During the initial start-up of a unit, the
surface tension properties of the fresh solution are such that the foaming may occur
during the first few days of operation. However, by following proper start-up
procedures, this foaming is easily avoided. In addition, this foaming tendency is only
experienced when the entire unit is filled with fresh solution, which only happens
during the initial start-up of the unit. Foaming does not occur during subsequent start-
ups.
Continuous incursions of small amounts of liquid hydrocarbons are frequently
experienced with no adverse effect on the operation of a unit; however, the
introduction of large amounts of liquid hydrocarbons can present foaming and
plugging problems. This would also be true of Claus units, selective oxidation
processes and hydrocarbon-based, redox systems. However, for aqueous-based redox
systems, "Designer" surfactants
1
have been developed, which in essence totally
alleviates the problems caused by the introduction of large amounts of liquid
hydrocarbons.
During the early days of liquid redox, sulfur plugging was a severe operating
problem. Packing plugged, static mixers plugged, pipes plugged, heat exchangers
plugged and distributors plugged. For the most part, all of these plugging problems
have been eliminated. Vessels with random packing are no longer used, on-line
cleaning procedures have been developed for static mixers
1
, which require very little
operator attention, proper pipe design has eliminated pipe plugging, proprietary heat
exchanger designs and proper operating procedures have minimized heat exchanger
plugging, newly designed absorber spargers are being installed, which have greatly
extended the life of sour gas spargers and improved quality control of oxidizer sparger
materials and proper operation of the process has minimized oxidizer sparger
plugging.
Operation of aqueous-based liquid redox systems at high pressure has been a problem
due to difficulties with keeping the liquid circulation pumps running. Circulation
pumps were always specified as ANSI, open-impeller centrifugal pumps. The logic
being that closed-impeller pumps would plug with sulfur particles or possibly erode.
Consequently, for high head applications in which open-impeller pumps would not
apply, plunger type pumps were chosen. The plunger pumps had no difficulty
supplying the required head; however, seal rings had extremely short lives. To solve
this problem, a multi-staged, closed-impeller, centrifugal pump was installed in one
high pressure application with excellent results. The pump was in continuos operation
for approximately1_ years without any signs of plugging or erosion. For all future
high-pressure applications, closed-impeller single or multi-stage centrifugal pumps
will be specified. Obviously, the original concern about plugging had no basis.
The Future
Although iron-based, liquid redox processes have gained acceptance as evidenced by
over 150 units being licensed worldwide, there are still areas in the process, which
need to be improved upon. Current areas of R&D efforts are reduction in operating
costs, reduction in equipment size and improvement in molten sulfur color.
Operating costs for aqueous, iron-based redox systems are composed of replacing
chemicals which are either oxidized in the unit or which are physically lost from the
unit and of electrical power required for circulating solution and injecting air. For any
iron-based system there is an economic tradeoff between iron concentration and the
solution circulation rate. Since 2 moles of iron are required for every mole of
hydrogen sulfide (equation 3), the amount of circulating solution required is
dependent on the iron concentration in the solution and the amount of H
2
S in the sour
gas stream the higher the iron concentration, the lower the circulation rate and
hence, the lower the power consumption. Conversely, the higher the iron
concentration, the higher the catalyst makeup rate required to replace iron from
physical losses such as solution lost with sulfur withdrawal. There is an optimum iron
concentration based on the incremental cost of power and the amount of solution,
which is normally lost from the system. This relationship is shown in Figure 5.
Besides replacing iron, which is physically lost from the system with the sulfur and
blowdown streams, chelating agents are chemically oxidized into useless, non-toxic
byproducts within the
system and must be replaced. As stated previously, different chelating agents have
different resistances to chemical oxidation. In addition, chemicals may be added to the
system or made in the unit, which act as free radical scavengers, thus retarding chelate
oxidation. Research continues on the development of oxidation resistant chelates and
on economical, free radical scavengers. For example, many compounds from the
polyamine family have proven to be excellent free radical scavengers reducing chelate
degradation to essentially zero. Unfortunately, the oxidation rates of the polyamines
are extremely high and consequently, uneconomical. Also new chelating agents have
been developed which have very high resistances to oxidation; however, they
currently are uneconomical to manufacture. The search for stable chelating agents
and/or economical free radical scavengers continues.
A large portion of the electrical consumption in an iron-based, liquid oxidation system
is associated with blowing air through the solution to satisfy the oxygen demand of
equation 5. Due to the low solubility of oxygen in water, a large excess of air is
generally employed depending on oxidizer design. Although the air is free, the back
pressure on the blowers is usually between 0.5 and 1.0 bar (g), thus the blower
usually represents a large portion of the units electrical consumption.
A considerable amount of research is currently underway to develop new mass
transfer devices which will improve the oxygen utilization in liquid oxidation systems
with the aim of reducing the quantity of air required (operating cost) and reducing the
size of the oxidizing vessels (capital cost). Currently, there are two types of oxidizers
employed -low head and high head oxidizers. In the low head oxidizers air is sparged
through approximately 3 meters of solution at superficial air velocities of less than 3.5
M/min by means of distributors equipped with EPDM sleeves which are perforated
with very small holes. Solution flow is perpendicular to the airflow. These oxidizers
are relatively poor mass transfer devices; however, they do provide much need
solution inventory for proper operation of the system.
In high head oxidizers air is sparged through approximately 7 meters of solution at
superficial velocities of greater than 10 M/min by means of course bubble pipe
distributors. Solution flow is co-current to the airflow. These oxidizers provide mass
transfer coefficients which are approximately 4 times better than the low head
oxidizers; however, this is at the expense of higher discharge heads on the air
blowers.
Neither the low or high head oxidizers are very good mass transfer devices; however,
they generally do not plug with sulfur and they do supply solution inventory required
for proper operation of the system. A main goal of current research is to develop a
mass transfer device, which will reduce the amount of air required to approximately
stoichiometric quantities, will reduce the oxidizer volume and will not plug with
sulfur. To this end, special synthetic membranes are being tested. Initial results
indicate that the first two objectives of the research stoichiometric air and high
mass transfer coefficients can be obtained. Long term testing is currently being
carried out to determine the plugging tendencies of the membranes. If this last phase
of testing is successful, liquid oxidation systems will become much smaller and less
expensive to operate.
Sulfur produced from liquid redox systems has the same chemical assay as Claus
sulfur, and it does have several commercial uses
2
in its unmelted form. In fact
Lubrizol in France has been recycling its produced sulfur with no adverse effect for
quite some time. However, there is always a desire to improve the appearance (color)
of redox sulfur, which is degraded due to the presence of iron polysulfides.
Development work is being conducted on a variety of filter/wash systems with the
goal of removing the chelated iron from the sulfur cake prior to final use. However,
due to the extremely low price of sulfur and due to the relatively low quantities of
sulfur produced in liquid redox plants, it is difficult justifying much work in this area.
Conclusions
Liquid phase oxidation systems have undergone considerable evolution during the
20
th
century, and this will continue into the 21
st
century. Foreseeable developments
for the near future will be smaller equipment sizes and lower operating costs which
will be achieved by the development of better oxygen mass transfer devices reducing
the amount of air required and the size of oxidizers and by the addition of free radical
scavengers into the systems.
References
1
Reicher, Myron, Niemiec, Bill & Katona, Tamas, "The Use of Liquid Redox
Desulfurization Technology for the treatment of Sour Associated Gases at Elevated
Pressure", presented at the GPA European Chapter Continental Meeting, 1999
2
Nagl, Gary, " Emerging Markets for Liquid Redox Sulfur", presented at Sulphur97,
Vienna, Austria
Table I. Liquid Phase Oxidation Processes
CHEMISTRY PROCESS
Polythionate Solutions Feld Process
Koppers C.A.S. Process
Iron Oxide Suspensions Burkheiser Process
Ferrox Process
Gluud Process
Manchester Process
Thioarsenate Solutions Thylox Process
Giammarco-Vetocoke
Process
Iron Cyanide Solutions Fischer Process
Staatsmijnen-Otto
Autopurification Process
ADA Solutions Stretford Process (4)
Takahax Process (4)
Iron Complex Solutions Cataban Process
Konos Process
CIP Process
Sulfint
Sulferox Process (4)
LO-CAT Process (4)
LO-CAT II Process (4)
(4) Indicates commercial
success
home | products/processes | news | downloads
locations | support | contact us
Suncors Optimization of a Sulfur
Recovery Facility
By Dean Freeman, Suncor,
J ackie Barnette, GTP LLC, Gary Nagl, GTP LLC
Introduction
Suncor Incorporated Resources Group acquired the 7-22 Progress Gas Plant,
located in Spirit River, Alberta, Canada, in 1996. Due to the extremely
competitive nature of the natural gas business, all gas processors, including
Suncor, are obsessed with reducing operating costs. As part of Suncors cost
reduction program, a close examination of their sulfur recovery unit by Suncor
and Gas Technology Products LLC resulted in significant cost savings by
optimizing the method of operation.
The Facility
The 7-22 Progress Gas Plant processes 20 MMSCFD of natural gas at
approximately 950 psig. As shown in Figure 1, the processing train consists of
an MDEA amine unit for removing CO2 and H2S, a glycol dehydrator and an
Autocirculation LO-CAT unit for removing the H2S in the amine acid gas
prior to exhausting to the atmosphere.
The LO-CAT process is a proprietary process, which converts H2S to
elemental sulfur by employing a patented, environmentally safe, multichelate,
iron catalyst. The overall reaction (Rx 1) of the process is the modified Claus
reaction; however, the mechanism for achieving this reaction is much different
than that which occurs in the Claus process.
The LO-CAT process is a liquid phase, ambient temperature process, which is
in contrast to a Claus unit, which is a gas phase, elevated temperature process.
The LO-CAT reactions can be separated into the Absorption Section and the
Regeneration Section. In the Absorption Section, the H2S is absorbed (Rx 2)
from the gas stream into the circulating aqueous (aq.) LO-CAT solution. Once
absorbed, the H2S ionizes (Rx 3) into hydrogen and hydrosulfide ions, and the
hydrosulfide ions then react (Rx 4) with ferric ions to form elemental, solid
sulfur and ferrous ions.
The ferrous ions are not capable of being reduced any further; consequently, to
have a continuous process they must be oxidized back to the ferric state. This is
accomplished by sparging air through the effluent solution from the Absorption
Section of the process. Oxygen is absorbed (Rx 5) into the solution, which then
oxidizes the ferrous ions (Rx 6) back to the ferric state.
Adding reactions 2 through 6 yields reaction 1 with all components in the
gaseous phase with exception of the sulfur, which is in the solid phase.
The LO-CAT unit employed at the Suncor plant was installed in 1990 and is
of the patented Autocirculation design, which is shown in Figure 2. In this
configuration, the Absorption and Regeneration Sections of the process are
located within the same vessel. The acid gas from the amine unit is sparged into
a centerwell (Absorber), which is nothing more than an open-ended pipe located
within a cone-bottom tank. The Absorption reactions (Rx 2 4) occur within
the centerwell. The regeneration air is sparged into the solution outside of the
centerwell where the regeneration reactions (Rx 5 & 6) occur. Since there is
considerably more regeneration air than acid gas, the solution outside of the
centerwell is more aerated (less dense) than the solution inside of the centerwell.
Consequently, this density difference creates a natural liquid circulation from the
Regeneration Section of the vessel to the Absorption Section. Thus liquid
circulation is established without the need of pumps.
Sulfur settles out of solution into the cone section of the Autocirculation Vessel
where it is removed as a 10 wt% to 15 wt% slurry. The sulfur slurry is heated to
approximately 120o C by heat exchange with hot oil, and the solid sulfur is
melted. The molten sulfur and LO-CAT solution are then separated, with the
solution being returned to the process. The melter system operates under
approximately 3.5 barg pressure to prevent the aqueous solution from boiling.
The molten sulfur is allowed to solidify, and is then hauled to a landfill. Due to
the remoteness of the plant and the relatively small amount of sulfur being
produced (2.2 MTPD), it is more economical to dispose of the sulfur at the local
landfill than to sell it to a remote user. Trucking the sulfur to a remote user will
cost more than what the sulfur is worth.
Even though water is produced in the process, a small amount of makeup water
is still required for the LO-CAT unit to compensate for the moisture consumed
in saturating the regeneration air. The plant originally used well water for this
purpose; however, the plant personnel discovered that some of the problems
they were experiencing in the unit, such as occasional foaming, disappeared
when they switched to deionized water. Obviously, the well water contained
surface active components which were conducive to foaming. In general, LO-
CAT units only require water of potable quality.
An Autocirculation LO-CAT unit is an extremely simple system to operate. In
essence, the unit consists of a cone-bottom tank through which air and acid gas
are sparged through an aqueous solution of chelated iron. A small slip stream of
concentrated sulfur slurry is pumped through a hot oil heat exchanger with
molten sulfur being withdrawn from the system, and solution being returned to
the cone-bottom tank. Operators attention is only required to test the solution
for pH and Redox potential once or twice a day.
Operating Costs Associated with the LO-CAT
Unit.
There are two major sources of operating costs associated with a liquid redox
process such as LO-CAT. They being the costs related to chemical makeup
and those related to power consumption. The major components of the power
costs for the Suncor unit involved two, rotary lobe blowers (65 KW/each) used
for blowing air into the process, and the major components of the chemical
makeup costs are associated with iron and chelate makeups and caustic addition
to the unit.
Chelates are water soluble, organic compounds which hold the iron in solution.
By employing the proper chelate, the solubility of iron in water can be increased
from a few parts per million to the 5 wt% range. The chelates will, over time,
oxidize by a free radical mechanism and require replacement. The rate at which
they oxidize can be controlled by utilizing a stabilizing agent, which acts as a
free radical scavenger.
The LO-CAT process utilizes a proprietary means of reducing chelate
degradation. Within the process, a small portion of the H2S is deliberately
converted to thiosulfate ions (S2O3=), which are excellent free radical
scavengers. In fact, many years of research by Gas Technology Products have
failed to result in a better free radical scavenger. By being able to generate
thiosulfate within the process, chelate replacement costs can be held to a
minimum with minimal effort.
Iron is lost from the system by physically removing solution from the unit. For
LO-CAT systems with sulfur melters, the major means of iron lost is by the
blowdown of solution from the unit to control solution specific gravity.
The specific gravity of a LO-CAT solution is dependent upon the amount of
salts, which are dissolved in the solution. Since LO-CAT operates at relatively
low iron concentrations, the chelated iron is not a major contributor to the
density of the solution. This is in sharp contrast to other redox processes. In a
LO-CAT unit, the major contributors to solution density are
carbonate/bicarbonate salts and thiosulfate/sulfate salts. Carbonate/bicarbonate
salts are formed when gas streams containing CO2 are being processed.
Depending on the CO2 partial pressure and the desired pH of the solution, CO2
will develop equilibrium concentrations of carbonate and bicarbonate as follows:
The equilibrium constants for each reaction are pH dependent, increasing with
increasing pH. Although the Suncor LO-CAT unit is processing an acid gas
stream containing a high concentration of CO2, the system is operating at
atmospheric pressure, which yields a relatively low CO2 partial pressure.
Consequently, the carbonate/bicarbonate concentrations in the solutions are also
low.
As previously discussed, thiosulfate formation is desirable as a means of
controlling chelate degradation. However, if solutions become too oxidizing
(high oxidation/reduction potential), thiosulfate can be oxidized to sulfate, which
has no beneficial value in the process. The formation of thiosulfate and sulfate
occur as follows:
It is important to note that the above reactions (Rx 7 11) all produce acidic
products (H+). Consequently, to maintain the solution in the slightly alkaline
range, which is required to promote good absorption of H2S, caustic in some
form (KOH, NaOH or NH3) must be added to the solution. The
thiosulfate/sulfate salts also contribute to increasing the specific gravity of the
solution.
If the concentrations of dissolved salts are allowed to increase unabated, a point
will eventually be reached when one or both of two things will occur. First, the
solution will become less capable of absorbing oxygen and H2S, which will
affect the ability of the process to remove H2S from a gas stream, and second,
the solution will eventually become saturated and salts will actually start
precipitating from the solution resulting in plugging problems. To prevent this
from happening, a small blowdown stream is taken. For systems, which have a
filter for removing sulfur from the unit, a sulfur cake is produced, which usually
contains sufficient solution to compensate for salt formation; however, in a
system, which produces molten sulfur such as Suncor?s, a liquid blowdown
stream is usually required. These blowdown streams represent a lost of iron from
the process, which require makeup iron to be added.
Unless there is a hazardous or toxic component in the gas stream being treated,
which is soluble in aqueous solutions, the blowdown liquid will be merely water
containing dissolved salts; however, it will have a chemical and biological
oxygen demand due to the chelates. Consequently, there is a cost associated
with treating the blowdown stream. In Suncors case the blowdown is hauled
away for remote treatment since there are no onsite wastewater treatment
facilities.
Suncors Optimization
Prior to Suncors purchase of the Spirit River facility, little attention was given
to the LO-CAT unit. In general, over injecting chemicals into a LO-CAT
unit will not result in operating problems, just higher than required operating
costs. Consequently, in remote gas plants such as Spirit River, it is sometimes
difficult to convince operators to change operating conditions if the unit is not
presenting any operating problems. However, this is not Suncors operating
philosophy.
Upon taking ownership of the facility, Suncor contacted Gas Technology
Products and stated that the operating costs associated with the LO-CAT unit
were not cost effective and something had to be done about chemical
consumption, power consumption and the disposal cost of blowdown liquid or
the unit would be shutdown. At this point, Suncor and Gas Technology
Products started working closely together to optimize the system.
The Suncor LO-CAT unit is operating at close to the design conditions of
123.4 Nm3/Hr of acid gas containing 57.5% H2S (2.19 MT/day of sulfur). As
suspected, an initial examination of the unit and a review of historical operating
data show that the chemical addition rates were much higher than the original
design rates, and that the operators were maintaining a lower solution specific
gravity than required by maintaining a higher than normal blowdown rate. For
example, the iron concentration was being maintained at more than twice the
design level while the chelate concentration was more than three times the
design level. In addition, the system was designed to operate with one air blower
in operation; however, the unit was being operated with both air blowers in
operation. These conditions resulted in a very positive, solution oxidation-
reduction potential (redox potential), which promoted the formation of sulfate
rather than thiosulfate resulting in a relatively high chelate oxidation rate.
Consequently, this highly oxidized solution state resulted in high salt formation
and thus a high blowdown rate to maintain the less than design solution specific
gravity. Consequently, the high blowdown rate resulted in a high iron
replacement rate and higher than required solution disposal costs. The unit was
also experiencing symptoms such as occasional sparger plugging, which
indicated that the solution was close to saturation.
The obvious remedy to Suncors problems was to get the solution chemistry
back to a normal state. This was accomplished by discontinuing the chemical
addition of the makeup chelate and the makeup iron. In addition, one air blower
was shutoff, thus immediately reducing power consumption by 50%. During
this period, GTP monitored the solution chemistry on a biweekly basis. Over a
relatively short period of time, the iron, chelate, and stabilizer concentrations and
the solution specific gravity were bought into line. At this time, the chemical
addition and blowdown rates were re-established, but at rates corresponding to
actual processing conditions of the unit. When the unit was operating at design
conditions, power consumption, chemical costs and disposal costs were reduced
by approximately 50%, thus achieving operating costs, which were in line with
Suncors requirements. In addition, problems with sparger plugging were greatly
reduced. All of these reductions were achieved while maintaining an H2S
removal efficiency of greater than 99.99+%. Table 1 summarizes the before and
after operating costs.
It is important to note that these cost savings were obtained by simply turning
pumps and blowers off. No daily detailed chemical analyzes were required, just
simple redox potential, pH and specific gravity readings. And although it took
years to get the LO-CAT solution in a state of near saturation, the situation
was remedied in a matter of weeks.
Although dramatic reductions in chemical costs were achieved at the Suncor
facility, even more chemical savings can be realized in more modern LO-CAT
units due to the ability to more accurately control thiosulfate concentrations.
Conclusions
A determined commitment to teamwork by Suncor and Gas Technology
Products has resulted in a significant reduction in plant operating costs in the LO-
CAT unit while maintaining high H2S removal efficiency and ease of
operation. As summarized by the plant operation staff ?Chemical consumption
and cost savings are important to Suncor. The ultimate is to remain emission free
while running as economical as possible. This process can run emission free
which will in turn guarantee the safety of the plant operators and our
environment.?
ATCO Midstreams Gas Sweetening
Experience Using Iron-Redox
Technology
LO-CAT unit provides highly reliable service
over 12 years of continuous operation.
By:
Gary Gialet Plant Supervisor
Curtis Sexsmith Operator
Rob Girard Maintenance
Neil McCagherty Area Superintendent
Neil Carnegie - Maintenance
Spencer Yelland - Operator
Dave Graubard, Business Development Engineer, GTP
ATCO Midstream (ATCO) works with natural gas producers to gather,
process, and store their natural gas and extract liquids from it. The ATCO LO-
CAT Unit, located in St. Albert, Alberta, Canada at the Carbondale plant, has
provided highly reliable service for over 12 years. The unit has continuously
been producing sweet gas at or below the minimum local requirement for H2S
emissions. ATCO is very pleased with the performance of the LO-CAT unit,
and expects many more years of LO-CAT operation at its St. Albert plant.
Importance of H2S Removal Technologies
Removal of hydrogen sulfide (H2S) from gas streams has been an issue for the
energy industry since its inception. Hydrogen sulfide is an extremely toxic,
corrosive and odorous gas, causing safety and materials issues in its unaltered
form. After burning, the H2S is oxidized to sulfur dioxide (SO2), a major
player in acid rain and greenhouse gas emissions for the downwind neighbors.
So, while sulfur removal from gas streams has been an issue since the inception
of the hydrocarbon-based energy industry, it also continues to get ever-
increasing attention as an environmental issue.
The iron-redox sulfur removal technology has been commercial for 25 years.
The technology has been a dominant process for hydrogen sulfide oxidation
and removal since its introduction due to its high removal efficiency, low cost
of operation, ease of operation and high reliability. Over 200 iron-redox plants
have been installed worldwide since its commercial introduction. The large
majority of these have been the LO-CAT process. ATCOs LO-CAT
experience shows why this technology has been so successful.
Iron-redox ?LO-CAT? process
The LO-CAT process is an aqueous, low temperature process that uses a
regenerable iron catalyst. The iron catalyst oxidizes the hydrogen sulfide to
elemental sulfur. The process is specific to hydrogen sulfide. Other gases,
including carbon dioxide and other sulfur compounds pass through the system
unreacted.
The intent of the process is to oxidize hydrosulfide (HS-) ions to elemental
sulfur by the reduction of the ferric (Fe+3) iron to ferrous (Fe+2) iron, and the
subsequent reoxidation of the ferrous ions to ferric ions by contact with air. The
chemistry of all chelated iron processes is summarized as follows with (l) and
(v) representing the liquid and vapor states, respectively;
Equations 1 and 2 represent the absorption of H2S into the aqueous, chelated
iron solution and its subsequent ionization, while equation 3 represents the
oxidation of hydrosulfide ions to elemental sulfur and the accompanying
reduction of the ferric iron to the ferrous state. Equations 4 and 5 represent the
absorption of oxygen into the aqueous solution followed by oxidation of the
ferrous iron back to the ferric state.
Equations 3 and 5 are very rapid. Consequently, iron-based systems generally
produce relatively small amounts of byproduct thiosulfate and sulfate ions, and
in properly designed units, air streams can actually be processed. However,
equations 1 and 4 are relatively slow and are the rate controlling steps in all
chelated iron processes.
It is interesting to note that the chelating agents do not appear in the process
chemistry, and in the overall chemical reaction, the iron cancels out. So the
obvious question is why is chelated iron required at all, if it doesnt take part in
the overall reaction. The iron serves two purposes in the process chemistry.
First, it serves as an electron donor and acceptor, or in other words, a reagent.
Secondly, it serves as a catalyst in accelerating the overall reaction. Because of
this dual purpose, the iron is often called a ?catalytic reagent?. The chelating
agent(s) do not take part at all in the process chemistry. All the chelating agents
do is solubilize iron in water, thus making it possible to have a solution of iron.
The two most common processing schemes encountered in iron-based, liquid
oxidation systems are illustrated in Fig. 1 and 2. Fig. 1 shows a ?Conventional?
unit, which is employed for processing gas streams, which are either
combustible or cannot be contaminated with air such as carbon dioxide, which
is being treated for beverage purposes. In this scheme, equations 1 through 3
are performed in the Absorber while equations 4 and 5 are performed in the
oxidizer. Fig. 2 illustrates an ?Autocirculation? unit, which is used for
processing acid gas (CO2 and H2S) streams or for other non-combustible
streams, which can be contaminated with air. In this scheme, equations 1
through 3 are performed in the ? Centerwell? which is nothing more than a
piece of pipe open on each end. The purpose of the centerwell is to separate the
sulfide ions. from the air to minimize byproduct formation. The volume within
the centerwell is essentially the same as the absorber in a conventional unit. The
other unique feature of the Autocirculation scheme is that no pumps are
required to circulate solution between the centerwell (absorber) and the
oxidizer. In these units there is a larger volume of air than acid gas;
consequently, the aerated density on the outside of the centerwell is less than on
the inside resulting in a natural circulation from the oxidizer into the centerwell.
Figure 1. Conventional LO-CAT II Unit
Figure 2. Autocirculation LO-CAT II Unit
LO-CAT technology can be applied to natural gas processing in both the
conventional configuration and the autocirculation configuration combined
with an amine unit upstream of the LO-CAT.
The amine/autocirculation LO-CAT combination is advantaged relative to the
conventional LO-CAT when 1) the gas treatment pressure is very high, 2)
when carbon dioxide needs to be removed from the gas stream, or 3) when the
H2S concentration is very low. The amine serves to concentrate the hydrogen
sulfide and reduce the size of the LO-CAT (the materials of construction are
lower for the amine unit than the LO-CAT, which is typically made of stainless
steel.) Reasons 1 and 2 applied in ATCO?s case.
The conventional LO-CAT is advantageous when the carbon dioxide does not
have to be removed. In this case, the LO-CAT can remove the hydrogen
sulfide with one process instead of two, reducing complexity, maintenance, and
operator attention.
Unit History
The unit in St. Albert was originally licensed and built for Norcen Energy
Resources in 1991. Located just north of Edmonton, Alberta, Canada, the unit
treats the acid gas from an amine unit located upstream. Environmental
regulations were and still are very strict in Alberta, especially where local
residents and ranch animals are located close to sour gas operations. Norcen
Energy did an investigation and found that LO-CAT was the technology best
suited for the H2S removal for their needs. The St. Albert unit was
commissioned in 1991 and has run continuously (albeit for scheduled
shutdowns or shutdowns due to the upstream amine unit) for 12+years. In
1994, ATCO began the process of purchasing the Industrial Gas System
division of Norcen Energy and took over the operations at the St. Albert plant
in early 1995.
Figure 3. Carbondale Plant and local resident
Being in an extreme winter environment, the ATCO LO-CAT unit (along with
3 other licensed LO-CAT II units in Alberta) was built to handle the cold
temperatures of northern Alberta. The Autocirculation LO-CAT system
includes a sulfur melter that produces a pure molten sulfur product. The system
was designed to operate in a temperature range of 32 C in summer to -40C in
winter, reflecting the extreme weather conditions in this region of Canada. The
vessels and pipes are insulated and heat traced, and a solution heater is installed
in the autocirculation vessel. The circulation pumps are indoors.
ATCO employs 3 people full-time to operate the Amine/LO-CAT plant, plus 2
maintenance persons with 50% of their time devoted to the plant. The plant is
staffed seven days per week from 8am-4:30pm. The plant runs unattended the
rest of the day. Manpower requirements for the LO-CAT unit are around 1 _ -
2 man-hours per day. The shift includes pulling a fluid sample every day and
analyzing it for specific gravity, sulfur separation, pH, redox, and catalyst
concentration and ratio. Other activities include sulfur handling, pump
adjustments, and filter cleanings.
ATCO Midstream Current Operating Conditions
The plant currently processes 34 MMSCFD at 600 pounds pressure. The H2S
concentration is about .07%.
The gas feed to the LO-CAT unit is about 0.7 MMSCFD, 12 pounds pressure,
and an H2S concentration of 33,000 ppm. The outlet H2S concentration is
below 1 ppm.
LO-CAT Performance
On-line reliability:
In 12 years of operation, the LO-CAT has never been the cause of a production
outage. If a minor upset does occur, the operators can accumulate product in
the LO-CAT vessel for some time (24 hours maximum) depending on how
much H2S is being processed. The ability to accumulate sulfur in the LO-CAT
solution for up to 48 hours without shutting down the production plant provides
flexibility in performing and scheduling routine maintenance.
Turnarounds:
Shutdowns are done each year over a period of 4-6 days. The liquid from the
autocirculation vessel is drained after the sulfur is removed. Storage is rented
for the LO-CAT solution. The LO-CAT autocirculation vessel is washed with
high-pressure water, along with the air and acid gas spargers, and the cooler
downstream of the overhead vent gas. The sulfur separator and melter are both
cleaned out (with HP water 20,000 psi water for melter, 10,000 psi water for
the LO-CAT vessels) during the turnaround.
The operators indicate that the LO-CAT is a very easy unit to start-up and
operate following shutdown. The solution is heated and circulated until the
solution reaches operating temperature (40oC), at which time the gas from the
amine unit is fed to the LO-CAT unit. Our new designs for a LO-CAT unit
allow for 24-36 months without the need for a turnaround for maintenance.
However, if there are other units in the plant that require yearly shutdowns, the
LO-CAT unit will be shutdown also for inspection.
Modifications to the LO-CAT unit
Modifications to the LO-CAT unit have been made in three major areas over
the years:

Odor control

Automated sparger washing

Increased agitation in the sulfur settling cone.
Mercaptan Odor Issues Addressed: The unit was originally designed
without provision for addressing odors due to mercaptans in the gas. Following
start-up, ATCO and GTP together designed a system to remove the odors
being emitted from the plant (see picture below). A fin-fan cooler was installed
to dry the saturated gas from the oxidizer vessel upstream of a new catalytic
oxidizer (incinerator). The moisture removed from the gas stream is returned to
the oxidizer vessel to minimize water lost from the system. Installation of the
cooler and incinerator have resolved the odor issues.
Figure 4. Odor control and water collection system
Automated sparger cleaning. The original LO-CAT unit had provision for
manually opening valves on a header system and water-washing the sparger
lines 3 times a day. After the 1994 shutdown, timers were installed to automate
the process. The more frequent washes have improved performance.
I ncreased agitation in the sulfur settling cone. Air injection ?rings? are
installed in the sulfur settling cone so that ?air blasts? can be injected into the
cone to agitate the sulfur slurry in the settling cone and prevent plugging. The
original valves did not seal properly and air flow was half the design flow.
Properly specified values and air flow have solved the plugging issues.
Figure 5. Air injection rings for cone bottom
Summary/Conclusions
ATCO is very satisfied with the operation and performance of their LO-CAT
unit.

The unit requires 1.5 to 2 man-hours of operation per day

The unit is unattended most of the day

The unit has never experienced an unplanned shutdown in 12 years of
operation.
The unit has provided very reliable service for over 12 years while meeting and
exceeding the environmental requirements for H2S removal and odor control.
The ATCO facility is in good standing with local residents and provincial
regulators.
Neil McCagherty, ATCO Midstream Area Supervisor states: "We have been
very happy with the performance and reliability of our LO-CAT unit. It has
helped to establish the Carbondale Plant as a well run environmentally friendly
plant in the eyes of regulators and our neighbors".
The operating issues experienced by ATCO are well understood by ATCO
and GTP and are reflected in current LO-CAT design. ATCO expects many
more years of reliable LO-CAT operation.
Acknowledgements
Gary Gialet Plant Supervisor
Curtis Sexsmith Operator
Rob Girard Maintenance
Neil McCagherty Area Superintendent
Neil Carnegie - Maintenance
Spencer Yelland - Operator
Doug Heguy Marketing Manager GTP
Bibliography
The State of Liquid-Redox J uly 2002
New Developments to a Long-Established Process Technology
By Douglas L. Heguy and Gary J . Nagl
HYDROCARBON PROCESSING / FEBRUARY 2002 45
C
l
e
a
n

F
u
e
l
s
D
e
s
u
l
f
u
r
i
z
a
t
i
o
n
C. Fredrick, Merichem Chemicals & Refinery Services
LLC, Houston, Texas
S
ulfur reduction in gasoline. People have been talking
about it for years. Refineries have been planning and
working to meet all the various regulations as the
sulfur specifications keep getting lower and harder to reach.
Refineries today are scrambling to meet not only the low
sulfur requirements, but also the imminent ultra-low sulfur
mandates. Billions of dollars will be invested in the next
few years to attain these sulfur levels. The big questions in
everyones mind are:
What to buy?
How much to spend?
What will be the payout?
Can the investment be delayed or staged?
Will the investment made for 30 wt ppm be stranded
capital or can it be modified to later reach 10 wt ppm?
And, most importantly, will any of the sulfur treating
technologies currently available actually work?
Many new technologies are being offered today to meet
the sulfur reduction demands being presented. Unfortu-
nately, the majority of them are unproven in commercial
refineries. Whether refiners were in total disbelief that the
low sulfur regulations would actually come to pass or the
ability to remove sulfur just took that long to be developed,
the technologies that refineries are betting on are pretty
much just thata bet. This is a huge bet for an industry that
inherently hates to take risks. The future of their gasoline
pool depends on the correct choice. Mistakes could set them
back millions of dollars and years of work.
Regulatory trends. The United States Environmental
Protection Agency (EPA) will require most refineries and
distributors to meet EPA Tier 2 regulations beginning in the
next three to four years. This regulation will require refiners
to meet a 30 wt ppm sulfur limit as compared with todays
average of 330340 wt ppm. Staged reductions must start in
2004. Early compliance in 2000-2003 will generate sulfur
credits, which can be used to partially offset the estimated
$8-billion cost to refiners to comply with the new limits.
1
European regulations call for levels of 50 wt ppm sulfur
by 2005, with some EU governments advocating even lower
sulfur levels prior to that time. Many European governments
are giving tax credits to refineries if they beat an earlier,
2004 deadline.
Future legislation in both the U.S. and Europe may
require sulfur levels as low as 10 wt ppm in the gasoline
pool, a level that very few of todays technologies can meet
without significant operating costs. Various lobbying groups
such as the automotive industry are also demanding zero sul-
fur in fuel. Most people believe this means meeting less than
5 wt ppm in the gasoline pool as a practical matter. Table 1
illustrates the regulatory trends for sulfur reduction.
What is the solution? Each technology for sulfur
reduction must be reviewed with deliberation and care.
Regardless of what each company offering a technology
choice may say, not all methods are appropriate for every
application.
TREATMENT OPTIONS
Since the primary contributor of sulfur to the gasoline pool
is FCC gasoline (approximately 90%), FCC gasoline is the
main focus of many refineries sulfur treatment efforts. The
two primary ways to attack the sulfur in the FCC gasoline
pool are pretreatment and post-treatment. Utilizing special
catalysts in the FCC may reduce sulfur levels, but these
catalysts cannot meet the requirements mandated by Tier 2
regulations.
Pretreatment. FCC feed pretreatment using hydrotreating
may be a viable option some refineries may choose. FCC
feed hydrotreating improves overall liquid yield as well as
quality and reduces the SO
X
emissions from the FCC unit.
Pretreatment of the FCC feed is probably the most expensive
way to reduce sulfur in gasoline. Estimates range as high as
$1,500$2,500/bbl to pretreat the FCC feed. All of this money
will probably not allow the refinery to meet the 30 wt ppm
sulfur specification required for the Tier 2 regulations, much
less meet a possible future 10 wt ppm sulfur specification.
Post-treatment. Post-treatment offers the refiner the larg-
Sulfur reduction:
What are the options?
Refiners must choose the technology that makes the most sense to them,
weighing initial capital expenditure, operating costs and product performance
Table 1. Gasoline sulfur specifications
5
Property North America Europe World Fuels Charter
EPA 2006 CaRFG3* Current 2005
Sulfur wt ppm 30 max 15 max 150 max 50 max 30 max
*CARB Phase 3 proposed averaging limit.
est number of options for treating sulfur. A variety of technolo-
gies are available, ranging from catalytic distillation to selective
hydrotreating to adsorption systems. Many of these are still
unproven in full-scale units or have very few units in operation
to measure their actual capabilities. Installation costs for each
unit also vary widely as do the operational costs in both utilities
and octane losses. Every refinery choosing one of these options
will have to carefully consider the pros and cons of each technol-
ogy before making its decisionand hope that the technologies
work as well as advertised. Table 2 compares properties for the
technologies summarized in the following discussion.
Catalytic distillation hydrotreating. One of the earli-
est technologies to come into the market was selective
hydrotreating via catalytic distillation. The single-bed system
reportedly achieves 90% desulfurization of FCC gasoline while
maintaining high yield and minimum octane losses. Distillation
is a significant benefit of this technology when used as a pre-
treatment step, whereby light sulfur compounds are reacted and
removed with the bottom product. This can eliminate the need
for caustic treating the light FCC gasoline fraction downstream
of the fractionation steps. Several of these units are currently
operating. The first was built in 1994.
An additional process involving catalytic distillation in
combination with hydrodesulfurization reportedly reduces the
sulfur approximately 95% in FCC gasoline. This is accom-
plished using a dual-bed system with hydrogen injection into a
distillation column. The light ends are fractionated in the upper
low temperature zone while the heavy ends are concentrated
into a high temperature zone. The primary goal is to maintain
olefin saturation, but still desulfurize. Reported results show
an octane loss of less than 1.0.
The two systems are used in combination by running the
FCC gasoline first through the single-bed column and then
through the dual-bed column for maximum sulfur reduction. In
the first column, mercaptan sulfur reacts with excess diolefins
to produce heavier sulfur compounds. The remaining diolefins
are partially saturated to olefins by reaction with hydrogen.
Bottoms from the first column are fed to the second column
where the mid and heavy naphtha are catalytically desulfurized
in the two separate reaction zones. Hydrogen is added to each
column at typical reformer hydrogen pressure levels.
The first unit using the dual-bed system started up in May
2000 to treat heavy FCC naphtha. The mercaptan levels in the
gasoline product have been low enough that the refinery has
been able to blend and ship gasoline with no further treatment
required.
Conventional hydrofining with octane recovery and
selective cat naphtha hydrofining. Another approach is to
fractionate the FCC naphtha into two or three streamslight
cat naphtha (LCN), intermediate cat naphtha (ICN) and heavy
cat naphtha (HCN)and treat those streams individually. The
ICN and HCN can be combined and selectively hydrotreated
to achieve less than 100 wt ppm sulfur with very little loss
of octane. If the endpoint of the LCN is kept relatively low
46 HYDROCARBON PROCESSING / FEBRUARY 2002
Table 2. Sulfur treating technology comparison
Technology Octane loss Volume loss Sulfur reduction Hydrogen cons. Commercial unit* Addl pros Addl cons
Feed HDS No N/A May not meet High Many 1) Impr. liquid yield Highest initial
30 wt ppm 2) Red. SO
X
emissions capital cost
Catalytic distillation Yes No 1030 wt ppm Yes 1st started up 1)Catalyst cost 2) May
hydrotreating in May 2000 produce recomb. RSH
3) High capital cost
Conventional No Up to 5% 10 wt ppm Yes Operating since 1991 1) Catalyst cost
hydrofining with 2) Total olefin sat
octane recovery and Rvp increase
Selective cat naphtha Yes** No 10 wt ppm Yes Yes 1)Catalyst cost
hydrofining 2) May produce
recomb. RSH
Dual-catalyst reactor Yes No 1030 wt ppm Limited First startup for No need for 1) Catalyst cost
unit producing 10 wt additional 2) Includes diolefin
sulfur expected in 2001. product sat and interstage
Several other units sweetening strip 3) May produce
in operation recomb. RSH
Low pressure Yes 0.32% 10 wt ppm Yes Yes 1)Requires MTBE (or
fixed-bed equiv.) addition for
hydroprocessing max yield case to
recover octane.
Octane neutral case
does not 2) Total olefin
sat and Rvp increase
Olefinic alkylation Yes Yes 10 wt ppm No One - Catalyst cost
Sorbent No Yield is almost 10 wt ppm Low Small-scale startup No recomb. 1) High initial capital
100% of original in 2001 RSH formed cost 2) Sulfur yielded
stream as SO
2
Extractive No No 10 wt ppm No No 1) Cost savings compared 1) Chemical costs
mass transfer *** to HDS as final polishing 2) RSH removal only
step 2) Preserves octane
* Not enough published data exists regarding feed and .
** Can be reduced when used in combination with extractive mass transfer technology.
*** Must be paired with a selective hydroprocessing unit.
(All information in Table 2 is reproduced from published articles regarding each technology.)
(150F), a significant portion of the sulfur in this stream will
be light mercaptans, which can easily be treated using caustic
extraction. Utilizing caustic treating for this stream prevents any
loss of octane that would occur if it were hydrotreated. The total
full-range naphtha stream can also be selectively hydrotreated if
a gasoline splitter is not economically justified.
Two commercially proven technologies have been devel-
oped for treating the ICN and HCN streams. The first process
approach uses an octane recovery technology that is very
similar to a conventional gasoline hydrofinisher or distillate
desulfurization unit. The process involves complete saturation
of olefins via hydrotreating followed by octane recovery via
isomerization to higher octane components (primarily isoparaf-
fins). Here, octane retention is the main advantage. The main
disadvantage is the loss of C
5
+
volumetric yield that accompa-
nies the relatively severe octane recovery step.
This process has been commercially proven, with the first
unit implemented in 1991. New catalyst improvements have
been implemented since the 1991 startup to improve volume
retention while maintaining octane.
The second process technology, selective cat naphtha hydro-
fining process, is a catalytic hydrodesulfurization process that
uses a proprietary catalyst developed for the selective removal of
sulfur from naphtha with minimum hydrogenation of olefins and
octane loss. Commercialization of this process was announced in
1998. A second generation of this technology can achieve product
sulfur levels between 10 and 50 wt ppm using a conventional
hydrotreating process configuration and a new, highly selective cat-
alyst. One of the features of this process is that to minimize olefin
saturation and octane losses, the severity of hydrotreating may be
reduced, allowing the formation of recombinant mercaptans. These
are formed when H
2
S reacts with olefins.
A modeling system has been developed by the licensor
that revolves around octane loss and recombinant mercaptan
formation. This modeling system is essential to predicting the
formation of recombinant mercaptans so they can be effec-
tively dealt with downstream of the unit. If the recombinant
mercaptans formation is not taken into account, the sulfur
specification may not be easily met without significant octane
losses required by running at higher severities.
The second generation of this technology can achieve 10
wt ppm sulfur, while in many cases reducing the octane loss
by as much as 50% from the original technology with some
incremental investment.
2
Dual-catalyst reactor. This technology was developed to
remove sulfur from heavy to mid-range naphthas with modest
octane loss and high gasoline yield. Increased requirements for
sulfur reductions have led to another generation of this technol-
ogy that utilizes a dual-catalytic concept. The second-generation
technology includes a selective hydrogenation reactor upstream
of a splitter with the dual-catalyst reactor system just downstream
of the splitter. The main reactions taking place in the reactor are
hydrogenation of diolefins, isomerization of the olefins double
bond and conversion of mercaptans to heavier sulfur species.
Staged investments may be possible allowing the first
investment to produce sulfur specifications ranging from
50150 wt ppm. The full implementation will reportedly meet
the 1030 wt ppm sulfur requirements. This technology allows
the reduction of olefins in the gasoline pool in the range of 10
to 15 vol%. Olefins may be further reduced, but this would
require higher hydrogen consumption and higher octane loss.
The first two units utilizing this technology were expected
to start up in Germany in 2001.
Low pressure, fixed-bed hydroprocessing. This method
utilizes proprietary, low-pressure, fixed-bed hydroprocessing
technology to selectively reconfigure the lower-octane compo-
nents of its gasoline-range feedstock. The licensor states that it
enables refiners to hydrotreat the sulfur-containing components
of a gasoline pool while also controlling the octane of the
hydrotreated product. The process can independently control
both the octane and product sulfur, which eliminates the octane
penalty typically associated with hydroprocessing.
3
This flex-
ibility is achieved by the use of a catalyst system that reportedly
promotes an array of octane-enhancing reactions.
The flow scheme for this technology is very similar to that
of a conventional naphtha hydrotreater. Capital and operating
costs are also similar to those of a hydrotreater. The cost sav-
ings involve the savings in octane by not requiring as much
MTBE to maintain the octane or by taking a loss on yield,
which is still less expensive than the addition of MTBE to a
hydrotreated stream.
Olefinic alkylation. This technology concentrates on the
thiophenes found in the naphtha stream produced by FCCs. Its
basis is the conversion of thiophenes to higher boiling point com-
pounds that can be readily removed from the gasoline stream.
The conventional method to remove thiophenes is hydrotreat-
ment, which consumes hydrogen and results in losses in octane.
This technology facilitates separation of the thiophenes by
catalytically causing them to react with olefins present in the
naphtha to produce heavier compounds. The higher boiling
sulfur fraction is then removed by fractionation and added to
the diesel refinery stream, where the sulfur can be removed
by hydrotreating. Between 1% and 4% of the feed stream is
separated and sent to the diesel stream.
This process is reported to remove up to 99.5% of the sulfur
from the gasoline stream. Reported octane losses are 2 or less
octane numbers. Product sulfur requirements of 10 wt ppm
can be met.
The first commercial application of this technology has
begun production. Two additional units are expected to come
online in 2002.
Sorbent. This technology utilizes a proprietary sorbent to
attract sulfur-containing molecules and remove the sulfur atom
from the molecule. The sulfur atom is retained on the sorbent,
while the hydrocarbon portion of the molecule is released back
into the process stream. H
2
S is not released into the product
stream, which prevents the recombination reactions of H
2
S and
olefins to make mercaptans.
4
The sulfur is removed in an offgas
stream as SO
2
that must be processed in the Claus unit.
This technology does not utilize any type of hydrotreating
technology, so typical hydrogen concerns of high consump-
tion rates and purity are not issues. In some cases, reformer
hydrogen may be an acceptable hydrogen source.
Several advantages noted by the licensor include yield
preservation, low octane losses, sulfur removal up to 10 wt
ppm and long run lengths. This technology can treat the entire
FCC naphtha stream or parts of the naphtha stream as required
by the refinery.
The first commercial unit started up in 2001 at the devel-
opers refinery. The unit processed 6,600 bpd of full-range
FCC naphtha.
Extractive mass transfer (post-hydrotreater sulfur
removal). A new liquid phase extraction technology has been
developed utilizing a special mass transfer device and a spe-
cially formulated treating solution to substantially enhance the
extraction of higher molecular weight (C
4
+
) mercaptan com-
pounds such as recombinant mercaptans produced after FCC
gasoline hydrotreatment. Individual studies have shown that
several of the available sulfur-treating technologies mentioned
earlier have the potential for recombinant mercaptan formation
as a trade-off to minimize olefin saturation.
This technology has been specifically designed to treat prod-
uct streams from the hydroprocessing sulfur treating units to
allow refiners to meet lower sulfur (10 wt ppm or less) standards
without losing octane. Many of the sulfur-treating technologies
will be able to meet the more stringent standards, but only if they
run at higher severities, causing significant octane losses. The
savings in octane losses frequently pay out the cost of the mass
transfer systems in as little as one to three years.
Capital expenditure for a grassroots system utilizing this
technology is 3550% of the cost of most incremental sec-
ond-stage hydrotreating systems. Operating costs per barrel
can be over 6070% less than hydrotreating. This technology
also provides staged investment options for additional sulfur
removal.
The main advantages are lower investment costs as compared
to a hydrotreating polishing step for final recombinant mercaptan
removal and no octane loss through the system. Using this tech-
nology also allows the other systems to be run at a much lower
severity, thus retaining more octane throughout the system.
The treating solution utilized is a specially formulated solu-
tion produced from common chemicals found in the refining
industry. There are no additional disposal requirements beyond
those of most common chemicals. The system is also regenera-
tive, so chemical usage is minimized.
Outlook. The possibilities for sulfur reduction are as varied as
their results. Some technologies will perform better regarding
loss of octane, while others will perform better regarding volume
losses. Each will be required to meet the specifications mandated
by the U.S. and international communities. The cost for some
technologies in initial capital expenditure may be very high, while
others may have very high operating costs. Regardless of refiners
reasonings, the choices will have to be made soon.
LITERATURE CITED
1
Barsamian, A., Blending Gasoline with Tier 2 Sulfur and MTBE Phaseout, World
Refining, September 2001.
2
Halbert, T. Dr., G. Brignac, J. Greeley, Dr. R. Demmin and E. Roundtree, Getting Sulfur
on Target, Hydrocarbon Engineering, June 2000.
3
Martinez, N., J. A. Salazar, J. Tejada, G. Anots, M. Anand and E. Houde, Meet Gasoline
Pool Sulfur and Octane Targets with the ISAL Process, 2000 NPRA Annual Meeting,
San Antonio, Texas, March 2000.
4
S Zorb Process Overview, Copyright 2000, Phillips Petroleum Company, www.szorb.
com/szorb_processover.htm.
5
Miller, R.B., A. Macris, M.G. Hunter and A.R. Gentry, Pre-treating vs Post-treating
Options Around the FCCU to Meet the Clean Fuels Challenges, ERTC Annual Meet-
ing, Rome, November 2000.
Cyndie Fredrick is the engineering manager for
Merichem Chemicals & Refinery Services LLC. Before
joining Merichem, she was a process engineer for
Conoco in the Excel Paralubes plant in Lake Charles,
Louisiana. She has approximately 10 years of experi-
ence in process operations, technical services and
engineering design in the refining industry. Ms. Fredrick
is a graduate of the University of Arkansas with a BS
degree in chemical engineering.
F. J. Suarez, Merichem Co., Houston, Texas
I
n recent years, refineries and petrochemical plants
worldwide have faced stricter controls on liquid
and gas effluent dicharge streams that could cause
air or water pollution. Spent caustic (NaOH) solutions
are liquid effluents that must be properly managed to
maintain the plant discharges quality. Since there are
different types of spent caustic streams, refiners must
correctly categorize them to use the most effective dis-
posal or treating method.
The hydrocarbon processing industry (HPI) has his-
torically used caustic solutions to extract or treat acidic
impurities such as hydrogen sulfide (H
2
S), mercaptans
and organic acids in hydrocarbon streams. Today, caus-
tic solutions continue to be the primary reagents used in
these treating operations because they have been proven
safe, economical, effective and, above all, environmentally
acceptable. When properly recycled or treated, used caustic
streams do not constitute damaging, hazardous waste.
Over 50 U.S. refineries and 10 outside the U.S. ship
caustic solutions to U.S. chemical plants. Yet these streams
are not classified as RCRA waste by EPA because they
are processed for beneficial reuse. Much of the concern
expressed today about caustic use in HPI operations can
be attributed to the following:
Many plant operators are unaware of options for in-

plant processing or recycling of spent caustic.
Poorly designed caustic treaters can cause operating

problems.
Spent caustic can be turned into hazardous waste by

outside disposal companies.
Unfounded concerns about caustic use, such as these

recent inaccurate statements: Spent caustic will be regu-
lated as hazardous waste by EPA and Spent caustic
disposal costs are as high as U.S.$3.00/gal.
Based on the economic benefits, caustic is still the best
treating reagent available to the HPI. In refineries, caus-
tic is primarily used to remove sulfur compounds from
light streams and oxidize mercaptans in heavier streams.
The pluses and minuses of caustic treating are presented
to help refiners and other petrochemical plant operators
make careful, intelligent economic choices. Although the
focus is on refinery treating operations, the information
presented applies equally well to many other petrochemi-
cal operations.
Removing sulfur compounds from light refinery
streams. The sulfur content of many refinery streams
HYDROCARBON PROCESSING / OCTOBER 1996 117
Pluses and minuses of
caustic treating
Proper use and spent solution
management ensure the safest and
most cost-effective operations
0.16
0.14
0.12
0.10
0.08
0.06
0.04
U
.
S
.
$
/
l
b
1986 87 88 89 90 91 92 93 94 1995
Year
Fig. 1. Average caustic prices (U.S. Gulf Coast).
Table 1. Comparison of capital and operating costs
for a 10,000-bpsd jet fuel caustic treater and a
comparable hydrotreater
Caustic treating Hydrotreating
Capital costs, U.S.$/bbl 150 to 200 1,500 to 2,500
Operating costs, U.S.$/bbl
Catalyst and chemicals .0172 .380
Utilities .0005 .025
Labor .0060 .012
Total .0237 .417
PROCESS TECHNOLOGY
must be reduced. Refinery gases, liquefied petroleum
gases and light naphthas contain sulfur primarily as H
2
S,
carbonyl sulfide (COS) and mercaptans that can easily
be extracted with caustic solutions. These streams are
almost universally treated with caustic (downstream of an
amine extraction system for bulk H
2
S removal) because
capital and operating costs are 80% to 95% lower than
hydrotreating costs. When compared to molecular sieves,
caustic treating is not only cheaper, but also far more reli-
able in meeting product specifications.
Used mercaptide rich caustic from these processes can
be regenerated in a catalytic treating system. Sulfidic
caustic solutions rich in Na
2
S/NaHS can easily be sold,
recycled or treated in situ while maintaining the attrac-
tive economics of caustic treating processes.
Oxidizing mercaptans to sweeten heavier streams.
Unfortunately, sulfur compounds in heavy fractions like
heavy naphtha, jet fuel and diesel are not caustic extract-
able. However, caustic solutions are widely used to convert
odorous and corrosive mercaptans to acceptable disulfide
oil via an air/catalyst oxidation (sweetening) process. If
the total sulfur content is already within product require-
ments, most gasoline, jet fuel, kerosine and diesel frac-
tions can be satisfactorily sweetened with caustic.
Hydrotreating, the most widely used alternative to
caustic sweetening, is very effective. However, hydro-
treating cannot compete with caustic treating in capital
and operating costs. Table 1 compares capital and oper-
ating costs of a 10,000-bpsd jet fuel caustic treater and
a comparable hydrotreater.
Caustic sweetening processes produce organic
byproducts (phenolic caustic and naphthenic caustic
solutions) that must be accounted for when designing
a treating plant. Cracked gasolines contain phenols, a
portion of which are incidentally extracted by the caus-
tic treating solution. For jet fuel, kerosine and diesel
streams, the sweetening process usually uses a caustic
prewash to remove all corrosive naphthenic acids, which
cannot be allowed into the final products. Phenolic and
naphthenic caustic solutions can either be sold or prop-
erly managed in the plant.
In recent years, an old wet sweetening process using
ammonia instead of caustic has been offered as a way
to eliminate coproduct caustic solutions. However, since
ammonia is hydrocarbon soluble and a weak base com-
pared to caustic, extra product cleanup steps and expen-
sive catalytic additives must be used, substantially
increasing treating costs.
In addition, the aqueous ammonia byproduct solution
and the ammonia-laden wash water can be even more dif-
ficult to manage than caustic treating byproducts. Ammo-
nia wastes cannot be recycled either in-plant or outside,
leaving only the option of in-plant waste processing.
If an organic ammonium salt solution is processed in
a refinery sour water stripper, organic acids remain in
the treated sour water and must then be oxidized in the
biological wastewater treating plant. The organic-rich
treated sour water should not be recycled to the crude
desalters, because the acids will eventually end up in the
distillates, to be treated again.
Advantages of caustic as a treating reagent. As
previously stated, aqueous caustic is a proven, safe and
economical chemical treating agent well-adapted for the
HPI and many other industries, including paper, alumi-
num and edible oil.
Economics. Fig. 1 shows caustic prices on the U.S.
Gulf Coast over the last 10 years. Caustic prices fluctu-
ate primarily due to demand for its coproduct, chlorine.
But over the long term, caustics price has increased at a
slightly lower rate than inflation. Refiners can dampen
price fluctuations by entering into long-term contracts as
opposed to buying caustic on the spot market. Caustic is,
and will continue to be, one of the lowest priced inorganic
bases available to the HPI.
Safety. Caustic is also safer than many other chemi-
cals used in the HPI. Storage, handling and personnel
protection requirements for caustic solutions are much
less rigorous than those for sulfuric acid, hydrofluoric
acid, gaseous ammonia, H
2
S, amines and many other
refinery chemicals.
Performance. In process units, caustic is easy to pump
and control. At operating temperatures below 200F, the
metallurgical requirement is typically low-cost carbon
steel.
Since caustic is not soluble in hydrocarbons, complete
phase separation can be achieved in a properly designed
treating unit. Some process designs use vigorous mixing
systems that tend to emulsify the caustic and hydro-
carbon phases. In these cases, a sand filter or water
wash will remove any entrained aqueous material from
the hydrocarbon product. Other modern processes can
affect contact between phases without mixing, result-
ing in clean phase separation without resorting to such
cleanup steps.
Spent caustic management. In comparing caustic
treating to alternative processes, the most critical issue,
after hydrocarbon product specifications and process eco-
nomics, is the management of byproduct spent caustic
solutions. Operating companies often choose a treating
process based on spent caustic disposal rather than the
favorable economics of caustic treating.
Spent caustic disposition, like any other refinery opera-
tion, requires careful evaluation. Unfortunately, many
engineering and technology firms that advise refiners
and design spent caustic handling systems do not have
the knowledge to optimize these systems. Errors made
early in the design process are compounded, resulting in
extremely costly economical and environmental mistakes.
These errors include:
118 HYDROCARBON PROCESSING / OCTOBER 1996
Table 2. Characteristics of a typical refinery
sulfidic caustic stream
Free NaOH, wt% 2 to 10
Na
2
S, NaHS as S
, wt% 0.5 to 4
Mercaptides as S, wt% 0.1 to 4
Carbonate as CO
3
, wt% 0 to 4
pH 13 to 14
Total Na
+
, wt% 4 to 10
Ammonia Traces
Mixing all types of spent

caustic in the same storage
vessel, rendering the entire
mixture unsalable
Designing caustic stor-

age systems that are too
small to allow for the lowest
possible transportation costs
Processing a mixture of
all types of caustics in a sin-
gle treating plant designed
for only one type
Controlling the pH
inadequately in the neu-
tralizers, which reduces the
effectiveness of contaminant
removal.
One of the most critical errors is assuming that all
refinery spent caustic streamssulfidic, cresylic and
naphthenicare alike and can be mixed and handled
together, either by an outside company or an internal
processing plant. Although this scenario might work in a
few cases, mixing spent caustic streams generally results
in higher disposition costs. For example, a refiner could
receive $0.05/gal for selling phenolic caustic while paying
$0.20/gal for removal of sulfidic caustic, but would not find
a market for the mixed caustic stream. Furthermore, the
refiner would pay a hazardous waste processor at least
$1.00/gal in disposal fees and would have to manifest the
mixed caustic as RCRA waste.
Alternatives for managing each type of spent
caustic. Sulfidic caustic. The composition of a typi-
cal refinery sulfidic caustic stream is in Table 2. The
key potential pollutants are sodium sulfide and sodium
mercaptide. These contribute to chemical and biological
oxygen demand (COD and BOD) in wastewater treating
plants, and produce odors and dangerous gases when
neutralized.
Sulfidic caustic solutions can be sold as treat-
ing agents to pulp and paper plants or to the mining
industry for purifying certain metal ores. Since these
end users require consistent quality, sulfidic caustic
is usually sold to intermediate companies that blend
the required product quality while providing just-in-
time transportation and delivery service. The total
sodium content of these streams is important as well as
the sodium-to-sulfur ratio. Although sulfidic caustic
solutions are valuable to the industries that use them,
in actual practice, transportation and handling
costs usually exceed product value. The refiner must
subsidize the operation with fees that can range from
$0.20/gal to $0.60/gal.
When production of sulfidic caustic is high or potential
end users are far away, resulting in high transportation
costs, in-plant processing may be the most economical
option. Here again, know-how is extremely important to
ensure that the treated caustic will not become an envi-
ronmental liability. Refiners have several options:
Deep neutralization to a pH below 4, coupled with

acid-gas handling to prevent transfer of pollutants from
the water to air. Neutralization to a pH of 7 does not
significantly reduce con-
taminants in these streams
and has been improperly
applied by many refiners
without much environmen-
tal benefit.
Partial oxidation of
sodium sulfide to sodium
thiosulfate. This allows
oxidation to be completed
in the wastewater treating
plant to avoid the risk of
releasing unsafe, odorous
H
2
S and mercaptans. Since
caustic is partially regen-
erated in the oxidation pro-
cess, it can also be used as
an alternative to fresh caustic in other plant processes.
Total oxidation of sodium sulfide to sodium sulfate

for maximum removal of COD and BOD before the waste-
water treating plant
Thermal incineration
Cascading to other treating systems for streams like

cracked gasoline while converting the caustic byproduct
to a more valuable product such as cresylic caustic.
Other options used by refiners like sending spent caus-
tic to the crude unit or the sour water stripper are not
considered reliable.
One option refiners try to avoid but often cannot is
outside disposal of sulfidic caustic as hazardous waste.
This can be economically avoided in most cases. The key
is to use high caustic strengths (>20Be) and segregate
the sulfidic product from other spent caustics.
Cresylic caustic. Cresylic acids are, in effect, part of
gasoline and do not reduce its quality. However, extract-
ing these acids from gasoline is sometimes more profit-
able than leaving them in. Cresylic caustic solutions
produced from treating cracked gasolines generally come
from two sources: 1) extraction or oxidation systems
using strong caustic; and 2) oxidation systems using
weak caustic. Table 3 shows typical characteristics of
cresylic caustics.
The first type of byproduct cresylic caustic solution
can be sold at fairly attractive prices, often covering the
value of the hydrocarbon content even after deducting
transportation costs. These streams typically contain at
least 10 wt% of phenolic compounds (average content
is 15 wt%) in addition to sulfur compounds like sodium
sulfide and mercaptans. Cresylic caustic processors
recover phenolic compounds for the production of valu-
able chemicals. When the refinery is far away from the
caustic processor, railroad or barge transportation costs
exceed the cresylic caustic streams value.
The second type of cresylic caustic byproduct contains
less than 5 wt% phenolics. The low acid oil content drasti-
cally increases transportation and processing costs. For
these reasons, this type of byproduct may be more eco-
nomical for in-plant processing. Cresylic caustic solutions
processed in-plant should be segregated from other spent
caustics and neutralized with a mineral acid or acid gas to
a pH of 7. Additional facilities are needed to solvent extract
the neutralized caustic to reduce levels of soluble phenol
and cresols in the water phase. The biological wastewater
Table 3. Characteristics of typical refinery cresylic
caustic streams
Strong caustic D i l u t e
caustic
operation operation
NaOH (at pH 7), wt% 10 to 15 1 to 4
Sulfide as S
, wt% 0 to 1 0 to 0.2
Mercaptide as S
, wt% 0 to 4 0 to 0.5
Cresylic acids, wt% 10 to 25 2 to 5
Carbonates as CO
3
=
, wt% 0 to 0.5 0 to 0.1
pH 12 to 14 12 to 14
treating plant may remove remaining phenolics, provided
the biological mass receives a steady diet of these com-
pounds without abrupt fluctuations in concentration or
total weight. Recovered acid oils can be sold or recycled to
refinery processes that tolerate the oils sodium content.
Naphthenic caustic. These solutions typically con-
tain 5 wt% to 15 wt% naphthenic acids, depending on the
caustic concentration, caustic spending target and acidity
of the jet fuel, kerosine or diesel stock being processed.
Table 4 shows typical characteristics of naphthenate
streams derived from kerosine and diesel stocks.
Naphthenic caustic solutions can be sold, often
resulting in positive value to the refiner, if distance or
low acid concentrations do not result in high freight
costs. Outside processors neutralize these solutions to
recover the naphthenic acids, then refine them for sale
to producers of naphthenate metal salts. Acids derived
from jet fuel/kerosine provide a high acidity in the 240
to 250 mg KOH/g range, while acids from diesel are on
the order of 180 to 200 mg KOH/g. Typically, the higher
acidity products are worth more in the marketplace. Net
return can be as much as two to four times the value of
an equivalent amount of diesel fuel.
For refiners whose treaters produce high volumes
of low-concentration naphthenic caustic solutions, in-
plant processing may be the most economical option.
Naphthenic solutions cannot be mixed and oxidized with
sulfidic caustic since sodium naphthenate creates vigor-
ous foaming during air injection.
Refiners should use a process that: 1) neutralizes
the caustic solution with a mineral acid to a pH of 3
to 4; 2) recovers the sprung acid oils and cleans up the
remaining organics; then 3) brings the pH up to the
range required for final treatment in the wastewater
treating plant. Sprung acid oils can be sold or recycled in
the refinery wherever sodium can be tolerated.
As mentioned earlier, one of the root causes of prob-
lems with caustic treating operations is lack of know-
how by both engineering companies and plant operat-
ing groups that design treaters and manage byproduct
caustic solutions. Poor design and management result
in processing and environmental problems, and finally,
in bad economic decisions.
With few exceptions, caustic treating processes are
extremely cost-effective and environmentally sound.
When sold or transferred as chemical feedstocks to out-
side chemical processors, none of these caustic solutions
are labeled hazardous waste by EPA, nor is such labeling
expected in the foreseeable future.
However, when quality specifications are ignored or
when spent caustic management is left to outside dis-
posal companies, spent caustic solutions can easily be
transformed into hazardous wastes.
Table 4. Characteristics of typical refinery
naphthenic caustic streams
Jet fuel/Kerosine Diesel
NaOH, wt% 1 to 4 1 to 4
Sulfide as S
, wt% 0 to 0.1 Trace

Mercaptide as S
=
, wt% 0 to 0.5 0 to 0.5
Naphthenic acids, wt% 2 to 10 2 to 15
Phenolics, wt% 1 to 3 0 to 1
pH 12 to 14 12 to 14
The author
Felipe J. Suarez is vice president and general manager of
the process technology division of Merichem Co., Houston,
Texas. He has served as special projects manager, technical
services manager, raw materials technical services manager,
proprietary technology group manager, assistant sales
manager and assistant general manager. From 1969 to
1980, he worked for Murphy Oil, Meraux, Louisiana, with
experience in refinery process design and operations. He
holds a BS degree in chemical engineering from Louisiana
State University in Baton Rouge, Louisiana.
HYDROCARBON PROCESSING / OCTOBER 1996 123

Refining Processes 2004 PDF

Uploaded by

Copyright:

Available Formats

Refining Processes 2004 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Refining Processes 2004 PDF

Uploaded by

Copyright:

Available Formats

What are some of the refining processes discussed in the document?

What are some of the refining processes discussed in the document?

What are the characteristics of typical refinery cresylic caustic streams?

What are the characteristics of typical refinery cresylic caustic streams?

Rening Processes Index

Per bbl olefin converted

Alkylation, sulfuric acid

Aromatics extractive distillation

Catalytic cracking (MSCC)

Installation: Thirty-six licensed units with a combined capacity of over

Dieselultra-low-sulfur diesel (ULSD)

Fluid catalytic cracking

Fluid catalytic cracking

Gasoline desulfurization, ultra-deep

Gasoline desulfurization, ultra-deep

Gasoline desulfurization, ultra-deep

) is oxidized under controlled conditions to elemental sul-

Lube oil refining, spent

Olefins-butenes extractive distillation

Resid catalytic cracking

Spent acid regeneration

Spent lube oil re-refining

Thermal gasoil process

Treatinggasoline and light

Treatingspent caustic deep

Process in the late

process in the late 1970s.

Many plant operators are unaware of options for in-

Poorly designed caustic treaters can cause operating

Spent caustic can be turned into hazardous waste by

Unfounded concerns about caustic use, such as these

Mixing all types of spent

Designing caustic stor-

Deep neutralization to a pH below 4, coupled with

Total oxidation of sodium sulfide to sodium sulfate

Cascading to other treating systems for streams like

, wt% 0 to 0.1 Trace

You might also like