Parts of A Mobile Cell Phone and Their Function
Parts of A Mobile Cell Phone and Their Function
Parts of A Mobile Cell Phone and Their Function
There are all kinds of parts and electronic components in a mobile cell phone. These parts and
components can be divided into Big Parts and Small Parts. This article explains all about big
parts and components in a mobile cell phone and their function.
When learning how to repair a mobile cell phone, it is important to identify its parts and
understand their function. Here I must also remind you that any PCB of a mobile phone is
divided into 2 sections namely: Network Section; and Power Section. Have a look at the image
below to understand PCB of a mobile cell phone.
Mobile Phone PCB Diagram with Parts
Big Parts of a Mobile Cell Phone and Their Function:
1. Antenna Switch: It is found in the Network Section of a mobile phone
Cell Phone Antenna Switch
and is made up of metal and non-metal. In GSM sets it is found in white color and in
CDMA sets it is found in golden metal.
Work: It searches network and passes forward after tuning.
Faults: If the Antenna Switch is faulty then there will be no network in the mobile
phone.
2. P.F.O: It is found near the Antenna Switch in the Network Section of the
Cell Phone PFO
PCB of Mobile Phone. It is also called P.A (Power Amplifier) and Band Pass Filter.
Work: It filters and amplifies network frequency and selects the home network.
Faults: If the PFO is faulty then there will be no network in the mobile phone. If it gets
short then the mobile phone will get dead.
3. RF IC / Hagar / Network IC: This electronic component found near
Cell Phone Network IC / RF IC
the PFO in the Network Section of a Mobile Phone. It is also called RF signal processor.
Work: It works as transmitter and receiver of audio and radio waves according to the
instruction from the CPU.
Faults: If the RF IC is faulty then there will be problem with network in the mobile
phone. Sometimes the mobile phone can even get dead.
4. 26 MHz Crystal Oscillator: It is found near the PFO in the Network
Mobile Phone 26 MHz Crystal Oscillator
Section of a Mobile Phone. It is also calledNetwork Crystal. It is made up of metal.
Work: It creates frequency during outgoing calls.
Faults: If this crystal is faulty then there will be no outgoing call and no network in the
mobile phone.
5. VCO: It is found near the Network IC in the Network Section of a Mobile
Mobile Phone VCO
Phone.
Work: It sends time, date and voltage to the RF IC / Hager and the CPU. It also creates
frequency after taking command from the CPU.
Faults: If it is faulty then there will be no network in the mobile phone and it will display
Call End or Call Failed.
6. RX Filter: It is found in the Network Section of a Mobile Phone.
Mobile Phone RX Filter
Work: It filters frequency during incoming calls.
Faults: If it is faulty then there will network problem during incoming calls.
7. TX Filter: It is found in the Network Section of a Mobile Phone.
Mobile Phone TX Filter
Work: It filters frequency during outgoing calls.
Faults: If it is faulty then there will network problem during outgoing calls.
8. ROM: It is found in the Power Section of a Mobile Phone.
Mobile Phone ROM
Work: It loads current operating program in a Mobile Phone.
Faults: If ROM is faulty then there will software problem in the mobile phone and the
set will get dead.
9. RAM: It is found in the Power Section of a Mobile Phone.
Mobile Phone RAM
Work: It sends and receives commands of the operating program in a mobile phone.
Faults: If RAM is faulty then there will be software problem in the mobile phone and it
will get frequently get hanged and the set can even get dead.
10. Flash IC: It is found in the Power Section of a Mobile Phone. It is also
Cell Phone Flash IC
called EEPROM IC, Memory IC, RAM IC and ROM IC.
Work: Software of the mobile phone is installed in the Flash IC.
Faults: If Flash IC is faulty then the mobile phone will not work properly and it can even
get dead.
11. Power IC: It is found in the Power Section of a Mobile Phone. There are
Cell Phone Power IC
many small components mainly capacitor around this IC. RTC is near the Power IC.
Work: It takes power from the battery and supplies to all other parts of a mobile phone.
Faults: If Power IC is faulty then the set will get dead.
12. Charging IC: It is found in the Power Section near R22.
Cell Phone Charging IC
Work: It takes current from the charger and charges the battery.
Faults: If Charging IC is faulty then the set will not get charged. If the Charging IC is short
then the set will get dead.
13. RTC (Simple Silicon Crystal): It is Real Time Clock and is found in
Mobile Phone RTC (Real Time Clock)
the Power Section near Power IC. It is made up of either metal or non-metal. It is of long
shape.
Work: It helps to run the date and time in a mobile phone.
Faults: If RTC is faulty then there will be no date or time in the mobile phone and the set
can even get dead.
14. CPU: It is found in the Power Section. It is also called MAD IC, RAP IC
Cell Phone CPU
and UPP. It is the largest IC on the PCB of a Mobile Phone and it looks different from all
other ICs.
Work: It controls all sections of a mobile phone.
Faults: If CPU is faulty then the mobile phone will get dead.
15. Logic IC / UI IC: It is found in any section of a mobile phone. It has 20
Cell Phone Logic IC
pins or legs. It is also called UI IC and Interface IC.
Work: It controls Ringer, Vibrator and LED of a mobile phone.
Faults: If Logic IC / UI IC is faulty then Ringer, Vibrator and LED of mobile phone will nor
work properly.
16. Audio IC: It is found in Power Section of a mobile phone. It is also
Cell Phone Audio IC
called Cobba IC and Melody IC.
Work: It controls Speaker and Microphone of a mobile phone.
Faults: If Audio IC is faulty then Speaker and Microphone of a mobile phone will not
work and the set can even get dead.