MC78LC00 Series Micropower Voltage Regulator: THIN SOT23 5 NTR Suffix CASE 483

MC78LC00 Series
Micropower Voltage
Regulator
Features
MARKING DIAGRAMS AND

PIN CONNECTIONS
THIN SOT235
NTR SUFFIX
CASE 483
GND
Vin
Vout
Low Quiescent Current of 1.1 mA Typical

Excellent Line and Load Regulation
Maximum Operating Voltage of 12 V
Low Output Voltage Option
High Accuracy Output Voltage of 2.5%
Industrial Temperature Range of 40C to 85C
Two Surface Mount Packages (SOT89, 3 Pin, or SOT23, 5 Pin)
PbFree Packages are Available
Typical Applications
4 N/C
1
(Top View)
SOT89
H SUFFIX
CASE 1213
GND 1
Vin 2
TAB
1
Battery Powered Instruments

HandHeld Instruments
Camcorders and Cameras
5 N/C
Vout 3
xx AYW G
G
http://onsemi.com
xxx AYW G
G
The MC78LC00 series of fixed output low dropout linear regulators

are designed for handheld communication equipment and portable
battery powered applications which require low quiescent current. The
MC78LC00 series features an ultralow quiescent current of 1.1 mA.
Each device contains a voltage reference unit, an error amplifier, a
PMOS power transistor, and resistors for setting output voltage.
The MC78LC00 has been designed to be used with low cost ceramic
capacitors and requires a minimum output capacitor of 0.1 mF. The
device is housed in the microminiature Thin SOT235 surface mount
package and SOT89, 3 pin. Standard voltage versions are 1.5, 1.8,
2.5, 2.7, 2.8, 3.0, 3.3, 4.0, and 5.0 V. Other voltages are available in
100 mV steps.
Tab
(Top View)
(Tab is connected to Pin 2)
Vin
VO
xxx = Version
A = Assembly Location
Y = Year
W = Work Week
G
= PbFree Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
Vref
1
GND
This device contains 8 active transistors.
Figure 1. Representative Block Diagram
Semiconductor Components Industries, LLC, 2006
January, 2006 Rev. 9
Publication Order Number:

MC78LC00/D
MC78LC00 Series
PIN FUNCTION DESCRIPTION

Pin No.
Pin Name
GND
Description
Vin
Positive power supply input voltage
Vout
Regulated Output
N/C
No Internal Connection
N/C
No Internal Connection
Power supply ground
MAXIMUM RATINGS
Symbol
Value
Unit
Input Voltage
Rating
Vin
12
Output Voltage
Vout
0.3 to Vin +0.3
Power Dissipation and Thermal Characteristics

Case 48301 (Thin SOT235) NTR Suffix
Power Dissipation @ TA = 85C
Thermal Resistance, JunctiontoAmbient
Case 1213 (SOT89) H Suffix
Power Dissipation @ TA = 25C
Thermal Resistance, JunctiontoAmbient
PD
RqJA
140
280
mW
C/W
PD
RqJA
300
333
mW
C/W
Operating Junction Temperature
TJ
+125
Operating Ambient Temperature
TA
40 to +85
Storage Temperature
Tstg
55 to +150
Tsolder
10
sec
Lead Soldering Temperature @ 260C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
http://onsemi.com
2
MC78LC00 Series
ELECTRICAL CHARACTERISTICS (Vin = Vout(nom.) + 1.0 V, Cin = 1.0 mF, Cout = 1.0 mF, TJ = 25C, unless otherwise noted.) (Note 5)
NTR SUFFIX
Symbol
Characteristic
Output Voltage (TA = 25C, Iout = 1.0 mA)
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.3 V
4.0 V
5.0 V
Vout
Output Voltage (TA = 40C to 85C)

1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.3 V
4.0 V
5.0 V
Vout
Min
Typ
Max
1.455
1.746
2.425
2.646
2.744
2.94
3.234
3.9
4.90
1.5
1.8
2.5
2.7
2.8
3.0
3.3
4.0
5.0
1.545
1.854
2.575
2.754
2.856
3.06
3.366
4.1
5.10
1.455
1.746
2.425
2.619
2.716
2.910
3.201
3.9
4.90
1.5
1.8
2.5
2.7
2.8
3.0
3.3
4.0
5.0
1.545
1.854
2.575
2.781
2.884
3.09
3.399
4.1
5.10
Unit
V
Line Regulation (Vin = VO(nom.) + 1.0 V to 12 V, Iout = 1.0 mA)
Regline
0.05
0.2
%/V
Load Regulation (Iout = 1.0 mA to 10 mA)
Regload
40
60
mV
Output Current (Note 6)

1.5 V, 1.8 V (Vin = 4.0 V)
2.5 V, 2.7 V, 2.8 V, 3.0 V (Vin = 5.0 V)
3.3 V (Vin = 6.0 V)
4.0 V (Vin = 7.0 V)
5.0 V (Vin = 8.0 V)
Iout
35
50
50
80
80
50
80
80
80
100
35
30
30
30
70
60
53
38
Dropout Voltage (Iout = 1.0 mA, Measured at Vout 3.0%)

1.5 V
1.6 V3.2 V
3.3 V3.9 V
4.0 V5.0 V
mA
mV
VinVout
Quiescent Current (Iout = 1.0 mA to IO(nom.))
IQ
1.1
3.6
mA
Output Voltage Temperature Coefficient
Tc
"100
ppm/C
Output Noise Voltage (f = 1.0 kHz to 100 kHz)
Vn
89
mVrms
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MILSTD883, Method 3015
Machine Model Method 200 V
2. Latch up capability (85C) "100 mA
3. Maximum package power dissipation limits must be observed.
TJ(max) * TA
PD +
RqJA
4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
5. Low duty pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
6. Output Current is measured when Vout = VO1 3% where VO1 = Vout at Iout = 0 mA.
http://onsemi.com
3
MC78LC00 Series
ELECTRICAL CHARACTERISTICS (Vin = Vout(nom.) + 1.0 V, Cin = 1.0 mF, Cout = 1.0 mF, TJ = 25C, unless otherwise noted.) (Note 11)
HT SUFFIX
Symbol
Characteristic
Output Voltage
30HT1 Suffix
33HT1 Suffix
40HT1 Suffix
50HT1 Suffix
Min
Typ
Max
2.950
3.218
3.900
4.875
3.0
3.3
4.0
5.0
3.075
3.382
4.100
5.125
0.05
0.2
40
40
50
60
60
60
70
90
35
35
45
55
50
50
65
80
40
35
25
25
60
53
38
38
1.1
1.1
1.2
1.3
3.3
3.3
3.6
3.9
100
Unit
V
(Vin = 5.0 V)
(Vin = 5.0 V)
(Vin = 6.0 V)
(Vin = 7.0 V)
Line Regulation
Vin = [VO + 1.0] V to 10 V, IO = 1.0 mA
Regline
Load Regulation (IO = 1.0 to 10 mA)

30HT1 Suffix (Vin = 5.0 V)
Regload
Output Current (Note 12)

Dropout Voltage
30HT1 Suffix
33HT1 Suffix
40HT1 Suffix
50HT1 Suffix
mV
IO
mA
Vin VO
(IO = 1.0 mA)

(IO = 1.0 mA)
(IO = 1.0 mA)
(IO = 1.0 mA)
Quiescent Current
ICC
Output Voltage Temperature Coefficient
TC
%/V
mV
mA
ppm/C
7. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MILSTD883, Method 3015
Machine Model Method 200 V
8. Latch up capability (85C) "100 mA
9. Maximum package power dissipation limits must be observed.
TJ(max) * TA
PD +
RqJA
10. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
11. Low duty pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
12. Output Current is measured when Vout = VO1 3% where VO1 = Vout at Iout = 0 mA.
DEFINITIONS
Load Regulation
difference between the input current (measured through the

LDO input pin) and the output current.
The change in output voltage for a change in output current

at a constant temperature.
Line Regulation
Dropout Voltage
The change in output voltage for a change in input voltage.

The measurement is made under conditions of low dissipation
or by using pulse technique such that the average chip
temperature is not significantly affected.
The input/output differential at which the regulator output

no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 3% below its
nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical over and undershoot response when input voltage is

excited with a given slope.
Maximum Power Dissipation
The maximum total dissipation for which the regulator will

operate within its specifications.
Maximum Package Power Dissipation
The maximum power package dissipation is the power

dissipation level at which the junction temperature reaches its
maximum operating value, i.e. 125C. Depending on the
ambient power dissipation and thus the maximum available
output current.
Quiescent Current
The quiescent current is the current which flows through the

ground when the LDO operates without a load on its output:
internal IC operation, bias, etc. When the LDO becomes
loaded, this term is called the Ground current. It is actually the
http://onsemi.com
4
MC78LC00 Series
3.2
3.2
VO, OUTPUT VOLTAGE (V)
3.1
3
IO = 1 mA
2.9
IO = 10 mA
2.8
2.7
2.6
IO = 5 mA
2.5
2.4
2.2
2.5
2.8
IO = 5.0 mA
2.6
2.4
MC78LC30HT1
IO = 10 mA
2.7
2.9
3.1
3.3
2.2
2.5
3.5
Vin, Input Voltage (V)
2.9
3.1
Figure 2. Output Voltage versus Input Voltage
2.7
3.3
3.5
3.2
3.05
NTR Series
40C
IO = 1.0 mA
3.0
TA = 25C
2.3
2.95
80C
2.9
2.85
2.8
2.75
25C
2.7
2.65
3.1
TA = 30C
3.0
2.9
20
40
60
80
100
TA = 25C
2.8
MC78LC30HT1
2.7
2.6
0
0
120
20
TA = 80C
100
120
IO, Output Current (mA)
40
60
80
Figure 4. Output Voltage versus Output Current
Figure 5. Output Voltage versus Output Current
2.0
Vin VO, DROPOUT VOLTAGE (V)
Vin VO, DROPOUT VOLTAGE (V)
TA = 25C
NTR Series
MC78LC30NTR
TA = 25C
1.8
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
0
10
20
30
40
1.6
1.2
0.8
0
0
50
MC78LC30HT1
TA = 25C
0.4
10
20
30
40
50
Figure 6. Dropout Voltage versus Output Current
Figure 7. Dropout Voltage versus Output Current
http://onsemi.com
5
MC78LC00 Series
3.10
MC78LC30NTR
Vin = 4.0 V
IO = 10 mA
3.06
3.1
3.02
2.98
2.94
2.9
40
20
20
40
60
3.06
3.02
2.98
MC78LC30HT1
2.94
2.90
40
80
20
20
40
60
80
TA, Ambient Temperature (C)
Figure 8. Output Voltage versus Temperature
Figure 9. Output Voltage versus Temperature
1.4
1.3
IQ, QUIESCENT CURRENT (mA)
MC78LC30NTR
TA = 25C
IO = 0 mA
1.2
1.1
1
0.9
0.8
3
10
11
TA = 25C
1.3
1.2
1.1
1.0
MC78LC30HT1
0.9
0.8
3.0
12
4.0
7.0
8.0
9.0
10
1.2
MC78LC30NTR
Vin = 4.0 V
IO = 0 mA
1.25
0.75
0.5
20
6.0
Figure 11. Quiescent Current versus Input Voltage
1.75
1.5
5.0
Figure 10. Quiescent Current versus Input Voltage
1.4
Vin = 5.0 V
IO = 10 mA
20
40
60
Vin = 5.0 V
1.1
1.0
0.9
0.8
0.6
40
80
MC78LC30HT1
0.7
20
20
40
60
80
Figure 12. Quiescent Current versus Temperature
Figure 13. Quiescent Current versus Temperature
http://onsemi.com
6
MC78LC00 Series
0.8
Vin Vout, DROPOUT VOLTAGE (V)
Vin Vout, DROPOUT VOLTAGE (V)
0.8
NTR Series
0.7
HT1 Series
0.7
0.6
IO = 10 mA
0.6
0.5
0.5
0.4
0.4
0.3
0.3
0.2
0.2
IO = 1.0 mA
0.1
0.1
0
0.0
2.0
1.0
3.0
4.0
5.0
0
0
6.0
1.0
2.0
VO, Set Output Voltage (V)
Output Voltage
Deviation (mV)
INPUT VOLTAGE/OUTPUT VOLTAGE (V)
Input Voltage (V)
6.0
NTR Series
5.0
4.0
Vin = 4.5 V to 5.5 V
Vout = 3.0 V
200
RL = 3 k
Cout = 0.1 mF
100
0
100
200
300
0.5
1.0
1.5
2.0
2.5
6.0
8.0
7.5
Input Voltage
7.0
6.5
6.0
HT1 Series
5.5
Output Voltage
5.0
CO = 0.1 mF
IO = 1.0 mA
4.5
4.0
0
2.0
6.0
4.0
t, Time (ms)
Figure 16. Line Transient
Figure 17. Line Transient Response
1.5
TA = 25C
3.0
NTR Series
Ig GROUND CURRENT (mA)
Vout, OUTPUT VOLTAGE (V)
5.0
Time (mS)
3.5
2.5
2.0
1.5
IO = 50 mA
1.0
100 mA
0.5
0
4.0
Figure 15. Dropout Voltage versus

Set Output Voltage
Figure 14. Dropout Voltage versus Set Output Voltage
300
3.0
VO, Set Output Voltage (V)
TA = 25C
IO = 0 mA
1.0
NTR Series
50 mA
0.8
200 mA
0.6
100 mA
50 mA
0.4
200 mA
0.2
200 mA
0
0.5
1.0
1.5
2.0
2.5
0.5
1.0
1.5
2.0
2.5
Figure 19. Ground Current versus Input Voltage
http://onsemi.com
7
MC78LC00 Series
APPLICATIONS INFORMATION
Thermal
A typical application circuit for the MC78LC00 series is

shown in Figure 20.
As power across the MC78LC00 increases, it might

become necessary to provide some thermal relief. The
maximum power dissipation supported by the device is
dependent upon board design and layout. Mounting pad
configuration on the PCB, the board material, and also the
ambient temperature effect the rate of temperature rise for
the part. This is stating that when the MC78LC00 has good
thermal conductivity through the PCB, the junction
temperature will be relatively low with high power
dissipation applications.
The maximum dissipation the package can handle is
given by:
Input Decoupling (C1)
A 0.1 mF capacitor either ceramic or tantalum is

recommended and should be connected close to the
MC78LC00 package. Higher values and lower ESR will
improve the overall line transient response.
Output Decoupling (C2)
The MC78LC00 is a stable component and does not

require any specific Equivalent Series Resistance (ESR) or
a minimum output current. Capacitors exhibiting ESRs
ranging from a few mW up to 3.0 W can thus safely be used.
The minimum decoupling value is 0.1 mF and can be
augmented to fulfill stringent load transient requirements.
The regulator accepts ceramic chip capacitors as well as
tantalum devices. Larger values improve noise rejection and
load regulation transient response.
PD +
If junction temperature is not allowed above the

maximum 125C, then the MC78LC00NTR can dissipate
up to 357 mW @ 25C.
The power dissipated by the MC78LC00NTR can be
calculated from the following equation:
Hints
Please be sure the Vin and GND lines are sufficiently

wide. When the impedance of these lines is high, there is a
chance to pick up noise or cause the regulator to
malfunction.
Set external components, especially the output capacitor,
as close as possible to the circuit, and make leads as short as
possible.
Battery or
Unregulated
Voltage
TJ(max) * TA
RqJA
Ptot + [Vin * Ignd (Iout)] ) [Vin * Vout] * Iout
or
P ) Vout * Iout
VinMAX + tot
Ignd ) Iout
If an 80 mA output current is needed then the ground

current from the data sheet is 1.1 mA. For an
MC78LC30NTR (3.0 V), the maximum input voltage will
then be 7.4 V.
+
C1
Vout
+
C2
Figure 20. Basic Application Circuit for NTR Suffixes
http://onsemi.com
8
MC78LC00 Series
MJD32C
0.033 mF
2
100
Vin
Vin
VO
MC78LC00
VO
MC78LC00
R1
1
0.1 mF
ICC
C1
0.1 mF
GND
R2
GND
GND
Figure 21. Current Boost Circuit
R2
Figure 22. Adjustable VO

MJD32C
Q1
0.033 mF
Q2
Vin
C2
MMBT2907
ALT1
VO
MC78LC00
R1
1
0.1 mF
0.1 mF
GND
GND
Figure 23. Current Boost Circuit with

Overcurrent Limit Circuit
+ V
O(Reg)
1 ) R2
) ICC R2
R1
http://onsemi.com
9
O(short circuit)
V BE2
R2
V BE1 ) V BE2
R1
MC78LC00 Series
ORDERING INFORMATION
Nominal
Output Voltage
Marking
Package
MC78LC15NTR
1.5
LAG
Thin SOT235
MC78LC15NTRG
1.5
LAG
Thin SOT235
(PbFree)
MC78LC18NTR
1.8
LAH
Thin SOT235
MC78LC18NTRG
1.8
LAH
Thin SOT235
(PbFree)
MC78LC25NTR
2.5
LAI
Thin SOT235
MC78LC25NTRG
2.5
LAI
Thin SOT235
(PbFree)
MC78LC27NTR
2.7
LAJ
Thin SOT235
MC78LC27NTRG
2.7
LAJ
Thin SOT235
(PbFree)
MC78LC28NTR
2.8
LAK
Thin SOT235
MC78LC28NTRG
2.8
LAK
Thin SOT235
(PbFree)
MC78LC30NTR
3.0
LAL
Thin SOT235
MC78LC30NTRG
3.0
LAL
Thin SOT235
(PbFree)
MC78LC33NTR
3.3
LAM
Thin SOT235
MC78LC33NTRG
3.3
LAM
Thin SOT235
(PbFree)
MC78LC40NTR
4.0
LEC
Thin SOT235
MC78LC40NTRG
4.0
LEC
Thin SOT235
(PbFree)
MC78LC50NTR
5.0
LAN
Thin SOT235
MC78LC50NTRG
5.0
LAN
Thin SOT235
(PbFree)
MC78LC30HT1
3.0
0C
SOT89
MC78LC30HT1G
3.0
0C
SOT89
(PbFree)
MC78LC33HT1
3.3
3C
SOT89
MC78LC33HT1G
3.3
3C
SOT89
(PbFree)
MC78LC40HT1
4.0
0D
SOT89
MC78LC40HT1G
4.0
0D
SOT89
(PbFree)
MC78LC50HT1
5.0
0E
SOT89
MC78LC50HT1G
5.0
0E
SOT89
(PbFree)
Device
Shipping
3000 Units/7 Tape & Reel
1000 Units Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative.
http://onsemi.com
10
MC78LC00 Series
PACKAGE DIMENSIONS
THIN SOT235
NTR SUFFIX
PLASTIC PACKAGE
CASE 48302
ISSUE E
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. MAXIMUM LEAD THICKNESS INCLUDES
LEAD FINISH THICKNESS. MINIMUM LEAD
THICKNESS IS THE MINIMUM THICKNESS
OF BASE MATERIAL.
4. A AND B DIMENSIONS DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
L
G
A
DIM
A
B
C
D
G
H
J
K
L
M
S
J
C
0.05 (0.002)
MILLIMETERS
MIN
MAX
2.90
3.10
1.30
1.70
0.90
1.10
0.25
0.50
0.85
1.05
0.013
0.100
0.10
0.26
0.20
0.60
1.25
1.55
0_
10 _
2.50
3.00
SOLDERING FOOTPRINT*
0.95
0.037
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm
inches
*For additional information on our PbFree strategy and soldering

details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
11
INCHES
MIN
MAX
0.1142 0.1220
0.0512 0.0669
0.0354 0.0433
0.0098 0.0197
0.0335 0.0413
0.0005 0.0040
0.0040 0.0102
0.0079 0.0236
0.0493 0.0610
0_
10 _
0.0985 0.1181
MC78LC00 Series
PACKAGE DIMENSIONS
SOT89
H SUFFIX
PLASTIC PACKAGE
CASE 121302
ISSUE C
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETERS
3. 121301 OBSOLETE, NEW STANDARD 121302.
C
J
L
K
D
0.10
E
G
T B
SEATING
PLANE
2 PL
0.10
T B
DIM
A
B
C
D
E
F
G
H
J
K
L
MILLIMETERS
MIN
MAX
4.40
4.60
2.40
2.60
1.40
1.60
0.37
0.57
0.32
0.52
1.50
1.83
1.50 BSC
3.00 BSC
0.30
0.50
0.80
4.25
INCHES
MIN
MAX
0.173
0.181
0.094
0.102
0.055
0.063
0.015
0.022
0.013
0.020
0.059
0.072
0.059 BSC
0.118 BSC
0.012
0.020
0.031
0.167
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including Typicals must be validated for each customer application by customers technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION

LITERATURE FULFILLMENT:
N. American Technical Support: 8002829855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 850821312 USA
Phone: 4808297710 or 8003443860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
291 Kamimeguro, Meguroku, Tokyo, Japan 1530051
Fax: 4808297709 or 8003443867 Toll Free USA/Canada
Phone: 81357733850
Email: orderlit@onsemi.com
http://onsemi.com
12
ON Semiconductor Website: http://onsemi.com

Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
MC78LC00/D

MC78LC00 Series Micropower Voltage Regulator: THIN SOT23 5 NTR Suffix CASE 483

Uploaded by

Copyright:

Available Formats

MC78LC00 Series Micropower Voltage Regulator: THIN SOT23 5 NTR Suffix CASE 483

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MC78LC00 Series Micropower Voltage Regulator: THIN SOT23 5 NTR Suffix CASE 483

Uploaded by

Copyright:

Available Formats

MC78LC00 Series

MARKING DIAGRAMS AND

Low Quiescent Current of 1.1 mA Typical

Battery Powered Instruments

The MC78LC00 series of fixed output low dropout linear regulators

Figure 1. Representative Block Diagram

Semiconductor Components Industries, LLC, 2006

January, 2006 Rev. 9

Publication Order Number:

PIN FUNCTION DESCRIPTION

Positive power supply input voltage

Power supply ground

0.3 to Vin +0.3

Power Dissipation and Thermal Characteristics

Operating Junction Temperature

Operating Ambient Temperature

Lead Soldering Temperature @ 260C

Output Voltage (TA = 40C to 85C)

Line Regulation (Vin = VO(nom.) + 1.0 V to 12 V, Iout = 1.0 mA)

Load Regulation (Iout = 1.0 mA to 10 mA)

Output Current (Note 6)

Dropout Voltage (Iout = 1.0 mA, Measured at Vout 3.0%)

Quiescent Current (Iout = 1.0 mA to IO(nom.))

Output Voltage Temperature Coefficient

Output Noise Voltage (f = 1.0 kHz to 100 kHz)

Load Regulation (IO = 1.0 to 10 mA)

Output Current (Note 12)

(IO = 1.0 mA)

Output Voltage Temperature Coefficient

difference between the input current (measured through the

The change in output voltage for a change in output current

The change in output voltage for a change in input voltage.

The input/output differential at which the regulator output

Line Transient Response

Typical over and undershoot response when input voltage is

Maximum Power Dissipation

The maximum total dissipation for which the regulator will

Maximum Package Power Dissipation

The maximum power package dissipation is the power

The quiescent current is the current which flows through the

VO, OUTPUT VOLTAGE (V)

Vin, Input Voltage (V)

Figure 2. Output Voltage versus Input Voltage

Figure 3. Output Voltage versus Input Voltage

VO, OUTPUT VOLTAGE (V)

VO, OUTPUT VOLTAGE (V)

IO, Output Current (mA)

Figure 4. Output Voltage versus Output Current

Figure 5. Output Voltage versus Output Current

Vin VO, DROPOUT VOLTAGE (V)

IO, Output Current (mA)

IO, Output Current (mA)

Figure 6. Dropout Voltage versus Output Current

Figure 7. Dropout Voltage versus Output Current

VO, OUTPUT VOLTAGE (V)

VO, OUTPUT VOLTAGE (V)

TA, Ambient Temperature (C)

Figure 8. Output Voltage versus Temperature

Figure 9. Output Voltage versus Temperature