Model 413

Remote Start
Owner’s Guide

© 2009 Directed Electronics, Vista, CA

G4103P 2009-07
Contents
Government Regulations..................................................................................... ii
Warning! Safety first......................................................................................... iii
What is Included ............................................................................................1
Important Information.........................................................................................1
System Maintenance..................................................................................1
Your Warranty...........................................................................................1
Remote Control Functions....................................................................................2
Standard Configuration..............................................................................2
Using Your System . ..........................................................................................3
Locking.....................................................................................................3
Unlocking.................................................................................................3
Disabling (optional) Starter Kill ...................................................................3
Panic Mode..............................................................................................4
Remote Start..............................................................................................4
Rear Defogger...........................................................................................5
Valet Take-Over.........................................................................................6
Timer Mode..............................................................................................7
Starter Anti-Grind Circuitry..........................................................................8
Disabling the Remote Start system................................................................8
Ignition Controlled Door Locks.....................................................................9
Rapid Resume Logic.........................................................................................10
Owner Recognition..........................................................................................10
Programming Options.......................................................................................11
Glossary of Terms............................................................................................12
Convenience Expansions .................................................................................13
Quick Reference Guide.....................................................................................15
Limited Lifetime Consumer Warranty...................................................................17
Notes.............................................................................................................19

© 2009 Directed Electronics. All rights reserved. i

Government Regulations
This device complies with Part 15 of FCC rules. Operation is subject to the fol-
lowing two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television, which can be determined by
turning the equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

This device complies with the Industry Canada Radio Standards Specification
RSS 210. Its use is authorized only on a no-interference, no-protection basis; in
other words, this device must not be used if it is determined that it causes harm-
ful interference to services authorized by IC. In addition, the user of this device
must accept any radio interference that may be received, even if this interference
could affect the operation of the device.

Warning:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.

ii © 2009 Directed Electronics. All rights reserved.

 Warning! Safety first
The following safety warnings must be observed at all times:

Due to the complexity of this system, installation of this product must only be
performed by an authorized Directed dealer.

When properly installed, this system can start the vehicle via a command signal
from the remote control. Therefore, never operate the system in an enclosed area
or partially enclosed area without ventilation (such as a garage). When parking
in an enclosed or partially enclosed area or when having the vehicle serviced,
the remote start system must be disabled using the installed toggle switch. It is
the user’s sole responsibility to properly handle and keep out of reach from chil-
dren all remote control devices to assure that the system does not unintentionally
remote start the vehicle. THE USER MUST INSTALL A CARBON MONOXIDE
DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED
OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES
REMAIN CLOSED. These precautions are the sole responsibility of the user.

Use of this product in a manner contrary to its intended mode of operation may
result in property damage, personal injury, or death. (1) Never remotely start the
vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with
the keys in the ignition. The user must also have the neutral safety feature of the
vehicle periodically checked, wherein the vehicle must not remotely start while
the car is in gear. This testing should be performed by an authorized Directed
dealer in accordance with the Safety Check outlined in the product installation
guide. If the vehicle starts in gear, cease remote start operation immediately and
consult with the authorized Directed dealer to fix the problem.

After the remote start module has been installed, contact your authorized dealer

© 2009 Directed Electronics. All rights reserved. iii

to have him or her test the remote start module by performing the Safety Check
outlined in the product installation guide. If the vehicle starts when performing
the Neutral Safety Shutdown Circuit test, the remote start unit has not been
properly installed. The remote start module must be removed or the installer must
properly reinstall the remote start system so that the vehicle does not start in gear.
All installations must be performed by an authorized Directed dealer.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN

GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERAT-
ING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT
IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY
CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AU-
THORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED
REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR
PAY FOR INSTALLATION OR REINSTALLATION COSTS.

This product is designed for fuel injected, automatic transmission ve-

hicles only. Use of this product in a standard transmission vehicle is
dangerous and contrary to the product's intended use.

iv © 2009 Directed Electronics. All rights reserved.

What is Included
• The control module
• An HX Plus receiver/antenna
• Two 4 - button remote controls (P/N 474P)
• A push-button Valet switch
• Your warranty card
• A shut-down toggle switch

Important Information
Congratulations on the purchase of your remote start keyless en-
try system. This system has been designed to provide years of trou-
ble free operation. By carefully reading this Owner’s Guide prior
to using your system, you will maximize the use of this system and
its features. Additional or replacement copies of this guide can be
printed by accessing the Directed Electronics internet website at
www.pythoncarsecurity.com.

➢ System Maintenance
The system requires no specific maintenance. Your remote is powered
by a miniature 3V CR2032 battery that lasts approximately one year
under normal use. When the battery weakens, the LED on the remote
dims and operating range will be reduced.

➢ Your Warranty
Your warranty card must be completely filled out and returned within
10 days of purchase. Your product warranty will not be honored if
your warranty card is not returned. Make sure that you receive the
warranty card from your dealer. You may also register online at
www.prodregister.com/directed.

© 2009 Directed Electronics. All rights reserved. 1

 Remote Control Functions
The receiver uses a computer-based learn routine to learn the remote
control buttons. The standard button configuration is described below.

➢ Standard Configuration
Button
The lock function is controlled by pressing button for one second.
When held for more than 1.5 seconds, Panic is activated.

Button
The unlocking function is controlled by pressing
�������

on the remote
control for one second. You can also turn Panic off with this button.

Button
�������

Silent Mode and an optional auxiliary function are controlled by press-

™

ing . Silent Mode works by pressing for less than one second
��� �������

before locking or unlocking. An optional trunk release is controlled by

pressing and holding for 1.5 seconds.
�������

Button
Remote start is activated when you press this button for one second.

�������
+ Buttons
Car Finder is controlled by pressing these two buttons.

+ +
�������
Buttons
When simultaneously pressed these buttons control the rear window
defogger during remote starting.

and Buttons
Timer mode is activated when you press these buttons.

2 �������
© 2009 Directed Electronics. All rights reserved.
Using Your System
➢ Locking
Pressing for one second locks the system. (if the door locks are con-
nected). The horn honks (if connected) and the parking lights flash once
to confirm locking of the system. The optional Failsafe® Starter Kill also
activates and prevents the vehicle’s starter from cranking.
�������

➢ Unlocking
Pressing for one second unlocks the doors (if connected). The horn
honks twice (if connected) and the parking lights flash twice to confirm
unlocking of the system. The optional Failsafe Starter Kill is deactivat-
ed.
�������

➢ Disabling (optional) Starter Kill

If your remote control is lost or damaged, you can manually override
the starter kill. To do this, you must have the ve­hi­cle's ignition key and
know where the Valet button is located. Be sure to check with the in-
staller for the location of the Valet button.

To override the starter kill, turn the ignition on and press

and release the Valet button within 10 seconds. The
vehicle should start. If it does not start, you may have
waited too long; turn the ignition off and repeat the
process.

Location of Valet button: ____________________

© 2009 Directed Electronics. All rights reserved. 3

➢ Panic Mode
If you are threatened in or near your vehicle, you can attract attention
by trig­ger­ing the system with your remote control. Press for 1.5
seconds to enter Panic Mode. In Panic Mode, the horn will honk and
the parking lights will flash for 30 seconds. To stop Panic Mode at
any time, press , or on the remote control.
�������

Note: In order for Panic Mode to be effective, the vehicle’s horn (or
optional siren) and the vehicle's parking lights must be connected.
�������

�������

➢ Remote Start
This feature allows you to remotely start and run your vehicle for a
pro­gram­ma­ble period of time. This makes it possible to warm up the
engine, as well as adjust the interior tem­per­a­ture of the ve­hi­cle with
the climate control system. If interior heating or cooling is desired, the
climate controls must be preset, and the fan blower must be set to the
desired level prior to remote starting the vehicle.

Important! Never remotely start the vehicle with the vehicle

in gear, and never remotely start the vehicle with the key in the
ignition.

To remote start the vehicle:

• Press the button on the remote control 1 time and hold for 1
second.
• The parking lights flash to confirm the vehicle is attempting to start.
(In gasoline vehicles, the engine will start 4 seconds after the park-
ing lights flash. In diesel vehicles, the engine will start when the
WAIT-TO-START timer has expired.)
• Once the vehicle has started, it will run for the pre-­pro­gram­med
period of time (12, 24, or 60 minutes) or until a shutdown input
is trig­gered.
4 © 2009 Directed Electronics. All rights reserved.
When you are ready to drive the vehicle:
1. Insert the ignition key and turn it to the ON (not the START)
po­sition.
2. Press the brake pedal. The remote start system shuts down and the
motor continues to run because the ignition has been turned on.

Note: If the brake pedal is pressed before the key is in the ON position,
the engine will shut down.

While the vehicle is running during remote start operation, the system
monitors the ve­hi­cle and automatically shuts down the engine if it receives
any of the following shut-down inputs:

• The brake pedal is pressed.

• The hood is opened.
• The shutdown toggle switch is put into the OFF position.
• The pre-programmed run time (12, 24, or 60 minutes) has elapsed.
• Remote control button is pressed.

➢ Rear Defogger

To turn the rear defogger Off:

1. Simultaneously press & release the + + buttons on the
�������

remote control.
2. The lights flash 2 times.
3. The rear defogger does not activate when the vehicle is remote
started. �������

Note: If the remote start is On, the parking lights turn Off then flash
2 times before returning to normal. The defogger, if active, stops.

© 2009 Directed Electronics. All rights reserved. 5

To turn the rear defogger On:
1. Simultaneously press & release the + + buttons on the
�������

remote control.
2. The lights flash 3 times.
3. The rear defogger activates when the vehicle is remote started.
�������

Note: If the remote start is On the lights turn Off then flash 3-times be-
fore returning to normal, and the defogger activates as programmed.

➢ Valet Take-Over
The Valet Take-Over feature allows the vehicle to remain running after
the key has been removed from the ignition. This feature is useful for
occasions when you wish to exit and lock the vehicle for short periods
of time, but would like to leave the motor running and the climate
controls on.

To perform Valet Take-Over:

1. Before turning off the engine, press and release on the remote
control for 1 second.
2. Turn the ignition key to the OFF position. (The engine will stay
running.)
3. The vehicle will run for the pre-­pro­gram­med period of time (12,
24, or 60 minutes) or until a shutdown input is trig­gered.

6 © 2009 Directed Electronics. All rights reserved.

➢ Car finder
Car finder allows you to locate your vehicle, by having the system flash
the parking lights on your vehicle..

To activate:
1. Press and release the and buttons at the same time.
�������

2. The lights flash 5 times slowly allowing you to locate your ve-
hicle.

➢ Timer Mode
When you activate timer mode the system automatically starts the ve-
hicle every three hours for a maximum of 6 starts. The pre-programmed
engine runtime is 12 minutes.

• Press and to activate timer mode. The parking lights flash

four times, and after a 1 second delay, the engine starts.
• To shutdown the engine, press the remote start button . The
�������

system remains in timer mode and will continue to start every 3

hours unless cancelled by turning on the ignition or by activating
�������

the brake, or neutral safety shutdown wires.

• The parking lights flash 4 times indicating timer mode is exited.

Important! Timer Mode should be used only in open

areas. Never start and run the vehicle in an enclosed space
such as a garage or carport.

© 2009 Directed Electronics. All rights reserved. 7

➢ Starter Anti-Grind Circuitry
Whenever the vehicle is remote started, advanced anti-grind circuitry
prevents the starter from engaging, even if the key is turned to the start
position. This prevents damage to the starter motor if the key is turned to
the start position during remote start operation.

Note: Anti-grind circuitry only works when the remote start system is
op­er­at­ing the motor and the optional Failsafe® Starter Kill relay is in-
stalled.

➢ Disabling the Remote Start system

This feature allows your system's remote start unit to be temporarily
disabled to prevent the vehicle from being remote started accidentally.
This feature is useful if the vehicle is being serviced or stored in an
enclosed area. To disable the remote start, move the shutdown toggle
switch to the OFF position. The switch can be installed in a location of
your choice. Check with your installer for recommended locations.

Location Of Shutdown Switch_________________________

8 © 2009 Directed Electronics. All rights reserved.

➢ Ignition Controlled Door Locks

If power door locks have been connected to your system, the vehicle's doors will
lock three seconds after the ignition has been turned On and unlock when the
ignition is turned Off.

Important: In order for the ignition controlled door locks to work the
feature must be programmed On.

If the ignition is turned on when the vehicle is remote started the doors
will not lock until the remote start shuts off. To avoid being locked out
of the vehicle, do not turn the ignition on until you are ready to drive
the vehicle.

© 2009 Directed Electronics. All rights reserved. 9

Rapid Resume Logic
This Directed Electronics system will store its current state to non-volatile
memory. If power is lost and then reconnected the system will recall the
stored state from memory. This means if the unit is in Locked Mode and
the battery is dis­con­nect­ed for any reason, such as servicing the car,
when the battery is re­con­nect­ed the unit will still be in Locked Mode.
This applies to all states of the system.

Owner Recognition
Owner Recognition is a revolutionary feature avail­able only from Di-
rected. Using a Directed Bitwriter® hand-held programming tool, your
dealer can program different settings for each trans­mit­ter that is used
with the system. Then, when a specific transmitter is used, the settings
assigned to that transmitter are recalled. Owner Rec­og­ni­tion lets up to
four users have different settings to meet their specific needs. It is almost
like having four separate alarms in your vehicle, one for each user.

Note: Owner Recognition cannot be programmed without a Bitwriter®

and the necessary soft­ware. Check with your dealer for more informa-
tion.

When using Owner Recognition, only the following features are avail-
able.
• Horn function
• Ignition locking and unlocking
• Activation pulses for remote start

10 © 2009 Directed Electronics. All rights reserved.

Programming Options
Programming options control your system's normal, operational set-up.
Most options do not require additional parts, but some may require ad-
ditional installation labor. This system's programming options are listed
below, with the factory default settings in bold:
• 12, 24, or 60 minute run time. your system can be programmed
to allow the vehicle to run for 12, 24, or 60 minutes when remote
started.
• 3, 6, 9, or 12 minute timer mode run time. Your system can be
programmed to allow the vehicle to run for 3, 6, 9, or 12 minutes
when remote started in timer mode. Can be set up from 1 to 16
minutes by your installer.
• Comfort closure is a programming option which closes the ve-
hicle’s windows after remote locking.
• Parking lights flashing or constant. Your system can be programmed
to either flash or to turn on the parking lights constantly during the
entire remote start operation.
• Ignition switch-controlled door-locking on or Off. With this feature
on, the doors will lock 3 seconds after the ignition key is turned on,
and unlock when the ignition key is turned off.
• The horn honk confirmations for locking and unlocking can be
programmed on or Off. In order for this feature to be programmed
on, the horn must be connected to the system.

© 2009 Directed Electronics. All rights reserved. 11

Glossary of Terms
Control Unit: The “brain” of your system. Usually hidden underneath the
dash area of the vehicle. It houses the microprocessor which monitors
your vehicle and controls all system functions.

Failsafe® Starter Kill: An optional automatic switch controlled by your

system which prevents the vehicle’s starter from cranking whenever the
system is locked. The vehicle is never prevented from cranking when
the system is unlocked, in Valet Mode, or if the starter kill switch itself
fails. Your system has feature-ready circuitry for the starter kill, however
installation may require additional labor and parts.

LED: indicator on your remote control when a button is pressed.

Remote control: A hand-held device which operates the various func-

tions of your system.

Valet Button: A small push button mounted at a discretionary location

inside the vehicle. It is used to override the Failsafe® Starter Kill when a
remote control is lost or damaged.

12 © 2009 Directed Electronics. All rights reserved.

Convenience Expansions
Listed below are some of the many expansion options available for
use with your system. Some options may require additional parts and/
or labor. Please consult with your dealer for a complete list of options
available for use with this system.

Power Door Lock Control: Your system is capable of controlling many

types of power door lock systems; however, some door lock systems
may require extra parts. Consult with your dealer to determine which
type of locks your vehicle uses. The system can be programmed to lock
the doors when the ignition is turned on and to unlock them when the
ignition is turned off.

Power Trunk Release: The system’s auxiliary output can be programmed

to operate a factory power release for the vehicle's trunk or hatch. If
the factory release is not power-activated, Directed Electronics 522T
trunk-release solenoid can often be added.

Power Window Control: Power window control is provided with Di-

rected Electronics 529T or 530T systems. The 529T system will roll
up two windows automatically when the system is locked, or roll two
windows down by using the remote control. The 530T will roll two
windows both up and down. The 530T also provides one touch switch
operation.

© 2009 Directed Electronics. All rights reserved. 13

 ✂
Quick Reference Guide
To lock using your remote
• To lock the system press for one second. The doors lock (if con-
nected). The ve­hi­cle’s horn (if connected) honks and the parking
Cut along the dotted line and fold to keep in purse or wallet for a quick and easy reference.

lights flash once to confirm locking.

�������

To unlock using your remote

• To unlock the system press for one second. The doors unlock (if
connected). The vehicle’s horn (if con­nect­ed) honks twice and the
parking lights flash twice. �������

Disabling the optional Failsafe® Starter Kill without a remote control

• Turn on the ignition. Press and release the Valet button with­in 10
sec­onds. The ve­hi­cle starts.

To remote start the vehicle

• Press for 1 second. The parking lights turn on (if connected)
and the vehicle starts. It will run for the programmed duration.

To activate Panic Mode

• Press and hold for 1.5 seconds.

To activate Timer Mode

• Press and to start the vehicle and run it for the set duration.
�������

The vehicle automatically restarts every three hours.

�������

To activate Car Finder

�������

• Press + to activate Car Finder, the vehicle lights flash 5

�������

times.
✂

© 2009 Directed Electronics. All rights reserved. 15

 ✂
To disable the remote start system
• To disable the remote start, move the shutdown toggle switch to
the OFF position.
Location of Shutdown Switch____________________________

Valet Takeover

Cut along the dotted line and fold to keep in purse or wallet for a quick and easy reference.
• Press and release on the remote control one time while the
vehicle is running. Turn the ignition key to the OFF position. The
vehicle remains running, and runs for the pre-­pro­gram­med peri-
od of time (12, 24, or 60 minutes).

Rear Window Defogger

• Press the ,
�������
and buttons simultaneously to turn the
defogger on or off when remote starting. When pressing these
buttons, the parking lights will flash 2-times if the defogger is set
to off, and will flash 3-times if the defogger is set to on.
�������

16 © 2009 Directed Electronics. All rights reserved.

Limited Lifetime Consumer Warranty
Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace (at
Directed’s election) with a comparable reconditioned model any Directed unit (hereafter the
“unit”), excluding without limitation the siren, the remote transmitters, the associated sensors
and accessories, which proves to be defective in workmanship or material under reason-
able use during the lifetime of the vehicle provided the following conditions are met: the
unit was purchased from an authorized Directed dealer, the unit was professionally installed
and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in
the vehicle in which it was originally installed by an authorized Directed dealer; and the
unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other
dated proof of purchase bearing the following information: consumer’s name, telephone
number and address; the authorized dealers name, telephone number and address; com-
plete product description, including accessories; the year, make and model of the vehicle;
vehicle license number and vehicle identification number. All components other than the
unit, including without limitation the siren, the remote transmitters and the associated sensors
and accessories, carry a one-year warranty from the date of purchase of the same. ALL
PRODUCTS RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF
PURCHASE WILL BE DENIED.
This warranty is non-transferable and is automatically void if: the original purchaser has
not completed the warranty card and mailed it within ten (10) days from the date of pur-
chase to the address listed on the card; the unit’s date code or serial number is defaced,
missing or altered; the unit has been modified or used in a manner contrary to its intended
purpose; the unit has been damaged by accident, unreasonable use, neglect, improper
service, installation or other causes not arising out of defects in materials or construction.
The warranty does not cover damage to the unit caused by installation or removal of the
unit. Directed, in its sole discretion, will determine what constitutes excessive damage and
may refuse the return of any unit with excessive damage.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING
BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-
INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND
DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME
FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS
OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED
SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE
THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST
VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS;
AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING
WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS

© 2009 Directed Electronics. All rights reserved. 17

WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR
REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND.
IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY,
THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN
THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED
SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE
PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME,
LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER
A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT TO
THE CONDITIONS AS DESCRIBED HEREIN. THIS WARRANTY IS VOID IF THE UNIT
HAS NOT BEEN PURCHASED FROM DIRECTED, OR AN AUTHORIZED DIRECTED
DEALER, OR IF THE UNIT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE,
NEGLIGENCE, ACTS OF GOD, NEGLECT, IMPROPER SERVICE, OR OTHER CAUSES
NOT ARISING OUT OF DEFECT IN MATERIALS OR CONSTRUCTION.
Some states do not allow limitations on how long an implied warranty will last or the exclu-
sion or limitation of incidental or consequential damages. This warranty gives you specific
legal rights and you may also have other rights that vary from State to State.
This warranty is only valid for sale of product(s) within the United States of America.
Product(s) sold outside of the United States of America are sold “AS-IS” and shall have NO
WARRANTY, express or implied. This product may be covered by a Guaranteed Protection
Plan (“GPP”). See your authorized Directed dealer for details of the plan or call Directed
Customer Service at 1-800-876-0800.

Make sure you have all of the following information from your authorized Directed dealer:
A clear copy of the sales receipt, showing the following:

o Date of purchase
o Your full name and address
o Authorized dealer’s company name and address
o Type of alarm installed
o Year, make, model and color of the automobile
o Automobile license number
o Vehicle identification number
o All security options installed on automobile
o Installation receipts 920-0003 06-06

18 © 2009 Directed Electronics. All rights reserved.

Notes

© 2009 Directed Electronics. All rights reserved. 19

Notes

20 © 2009 Directed Electronics. All rights reserved.

 The company behind this system is Directed Electronics
Since its inception, Directed Electronics has had one purpose, to provide
consumers with the finest vehicle security and car stereo products and
accessories available. The recipient of nearly 100 patents and Innovations
Awards in the field of advanced electronic technology.

Directed is ISO 9001 registered.

Quality Directed Electronics products are sold and serviced throughout

North America and around the world.

Call (800) 274-0200 for more information about our products and services.

G4103P 2009-07

Vista, CA 92081
www.directed.com
© 2009 Directed Electronics—All rights reserved