CIP25-Corrosion of Steel in Concrete

Copyrighted information from the National Ready Mixed Concrete Association. All rights reserved.
Reproduction prohibited without permission. Print copies can be obtained from NRMCA (301) 587-1400 x 101
NRMCA
What, Why & How?

Corrosion of Steel
in Concrete
CONCRETE IN PRACTICE
CIP 25
WHY Does Steel in Concrete Corrode?

Steel in concrete is usually in a noncorroding, passive
condition. However, steel-reinforced concrete is often
used in severe environments where sea water or deicing salts are present. When chloride moves into the
concrete, it disrupts the passive layer protecting the steel,
causing it to rust and pit.
WHAT is Corrosion of Steel?

ASTM terminology (G 15) defines corrosion as the
chemical or electrochemical reaction between a material, usually a metal, and its environment that produces
a deterioration of the material and its properties. For
steel embedded in concrete, corrosion results in the formation of rust which has two to four times the volume
of the original steel and none of its good mechanical
properties. Corrosion also produces pits or holes in the
surface of reinforcing steel, reducing strength capacity
as a result of the reduced cross-sectional area.
WHY is Corrosion of Steel a Concern?

Reinforced concrete uses steel to provide the tensile
properties that are needed in structural concrete. It prevents the failure of concrete structures which are subjected to tensile and flexural stresses due to traffic,
winds, dead loads, and thermal cycling. However, when
reinforcement corrodes, the formation of rust leads to
a loss of bond between the steel and the concrete and
subsequent delamination and spalling. If left unchecked,
the integrity of the structure can be affected. Reduction in the cross-sectional area of steel reduces its
strength capacity. This is especially detrimental to the
performance of tensioned strands in prestressed concrete.
Carbonation of concrete is another cause of steel corrosion. When concrete carbonates to the level of the
steel rebar, the normally alkaline environment, which
protects steel from corrosion, is replaced by a more
neutral environment. Under these conditions the steel
is not passive and rapid corrosion begins. The rate of
corrosion due to carbonated concrete cover is slower
than chloride-induced corrosion.
Occasionally, a lack of oxygen surrounding the steel rebar
will cause the metal to dissolve, leaving a low pH liquid.
HOW to Prevent Corrosion?

Quality ConcreteConcrete Practices
The first defense against corrosion of steel in concrete
is quality concrete and sufficient concrete cover over
the reinforcing bars. Quality concrete has a water-tocementitious material ratio (w/c) that is low enough to
slow down the penetration of chloride salts and the development of carbonation. The w/c ratio should be less
than 0.50 to slow the rate of carbonation and less than
0.40 to minimize chloride penetration. Concretes with
low w/c ratios can be produced by (1) increasing the
cement content; (2) reducing the water content by using
water reducers and superplasticizers; or (3) by using
larger amounts of fly ash, slag, or other cementitious
materials. Additionally, the use of concrete ingredients
containing chlorides should be limited. The ACI 318
Building Code provides limits on the maximum amount
of soluble chlorides in the concrete mix.
Another ingredient for good quality concrete is air entrainment. It is necessary to protect the concrete from
freezing and thawing damage. Air entrainment also reduces bleeding and the corresponding increased permeability due to the bleed channels. Spalling and scaling can accelerate corrosion damage of the embedded
reinforcing bars. Proper scheduling of finishing operations is needed to ensure that the concrete does not scale,
spall, or crack excessively.
The correct amount of steel will help keep cracks tight.
ACI 224 helps the design engineer to minimize the formation of cracks that could be detrimental to embedded steel. In general, the maximum allowable crack
widths are 0.007 inch in deicing salt environments and
0.006 inch in marine environments.
Adequate cover over reinforcing steel is also an important factor. Chloride penetration and carbonation will
occur in the outer surface of even low permeability
concretes. Increasing the cover will delay the onset of
corrosion. For example, the time for chloride ions to
reach a steel rebar at 2 inches from the surface is four
times that with a 1 inch cover. ACI 318 recommends a
minimum of 1.5 inches of cover for most structures,
and increases it to 2 inches of cover for protection from
deicing salts. ACI 357 recommends 2.5 inches of minimum cover in marine environments. Larger aggregates
require more cover. For aggregates greater than 3/4 inch,
a rule of thumb is to add to the nominal maximum aggregate size 3/4 inch of cover for deicing salt exposure,
or 1-3/4 inch of cover for marine exposure. For example,
concrete with 1 inch aggregate in a marine exposure
should have a 2-3/4 inch minimum cover.
The concrete must be adequately consolidated and
cured. Moist curing for a minimum of seven days at
70F is needed for concrete with a 0.40 w/c ratio,
whereas six months is needed for a 0.60 w/c ratio to
obtain equivalent performance. Numerous studies show
that concrete porosity is reduced significantly with increased curing times and, correspondingly, corrosion
resistance is improved.
Modified Concretes and Corrosion Protection Systems

Increased corrosion resistance can also come about
by the use of concrete additives. Silica fume, fly ash,
and blast-furnace slag reduce the permeability of the
concrete to the penetration of chloride ions. Corrosion
inhibitors, such as calcium nitrite, act to prevent corrosion in the presence of chloride ions. In all cases, they
are added to quality concrete at w/c less than or equal
to 0.45.
Water repellents may reduce the ingress of moisture
and chlorides to a limited extent. However, ACI 222
indicates that these are not effective in providing longterm protection. Since good quality concrete already
has a low permeability, the additional benefits of water
repellents are not as significant.
Other protection techniques include protective membranes, cathodic protection, epoxy-coated reinforcing
bars, and concrete sealers (if reapplied every four to
five years).
References
1. Building Code Requirements for Reinforced Concrete, ACI
318, American Concrete Institute, Farmington Hills, MI.
2. Corrosion of Metals in Concrete, American Concrete
Institute, Farmington Hills, MI.
3. Control of Cracking in Concrete Structures, ACI 224R,
American Concrete Institute, Farmington Hills, MI.
4. Design and Construction of Fixed Offshore Concrete
Structures, ACI 357R, American Concrete Institute,
Farmington Hills, MI.
5. Perenchio, W.F., Corrosion of Reinforcing Steel, ASTM STP
169C, 1994, pp. 164-172.
6. Whiting, D., ed., Paul Klieger Symposium on Performance of
Concrete, ACI SP-122, 1990, 499 pp.
7. Berke, N.S., Corrosion Inhibitors in Concrete, Concrete
International, Vol. 13, No. 7, 1991, pp. 24-27.
8. Berke, N.S., Pfeifer, D.W., and Weil, T.G., Protection Against
Chloride Induced Corrosion, Concrete International, Vol. 10,
No. 12, 1988, pp. 44-55.
HOW to Limit Corrosion

1. Use good quality concrete-air entrained with a w/c of 0.40, or less.
2. Use a minimum concrete cover of 1.5 inches and at least 0.75 inch larger than the nominal maximum size
of the coarse aggregate.
3. Increase the minimum cover to 2 inches for deicing salt exposure and to 2.5 inches for marine exposure.
4. Ensure that the concrete is adequately cured.
5. Use fly ash, blast-furnace slag, or silica fume and/or a proven corrosion inhibitor.
Technical information prepared by
National Ready Mixed Concrete Association
900 Spring Street
Silver Spring, Maryland 20910
Printed in U.S.A.
National Ready Mixed Concrete Association.

All rights reserved.
No part of this publication may be reproduced in any form, including
photocopying or other electronic means, without permission in writing
from the National Ready Mixed Concrete Association.
Copyright NATIONAL READY MIXED CONCRETE ASSOCIATION, 1995
CIP 100/25/0060/10.0/DMSC

CIP25-Corrosion of Steel in Concrete

Uploaded by

Copyright:

Available Formats

CIP25-Corrosion of Steel in Concrete

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CIP25-Corrosion of Steel in Concrete

Uploaded by

Copyright:

Available Formats

Copyrighted information from the National Ready Mixed Concrete Association. All rights reserved.

What, Why & How?

WHY Does Steel in Concrete Corrode?

WHAT is Corrosion of Steel?

WHY is Corrosion of Steel a Concern?

HOW to Prevent Corrosion?

Modified Concretes and Corrosion Protection Systems

HOW to Limit Corrosion

National Ready Mixed Concrete Association.

Copyright NATIONAL READY MIXED CONCRETE ASSOCIATION, 1995

You might also like