Professional

1
english USER MANUAL
PROFESSIONAL
CHRONOGRAPH
MOVEMENT
RONDA 5040.D
SWISS MADE WATCHES
2
English User Manual
We would like to thank you for choosing an exclusive AVIATOR watch. Your timepiece was
made and tested using meticulous techniques and premium materials of which we assure the
authenticity.
We certify that your AVIATOR watch is guaranteed against material and manufacturing defects
for 24 months starting from the date of purchase from an official authorised dealer.During this
period of time, the repairs and exchange of defective parts under warranty will be carried free
of charge. This excludes failures due to accidents or careless use.
To fulfil this requirement with any of our international distributors and service centres, your
watch must be accompanied by the international guarantee certificate/card signed by the authorised dealer where the watch was purchased.
The shipping and insurance expenses will be charged to the owner of the watch. AVIATOR/
BURAN SA and the authorised distributors reserve all rights for repair, in accordance with this
warranty.
IMPORTANT:
This warranty does not cover the following parts:
-Damages and or failure in working due to wrong repairing or tampering, to careless use, to
negligence, to changes made to the original structure of the case or band or to intervention
made by people who are not authorised by AVIATOR/BURAN SA;
-Damages to the lens, breaking or scratching on the case, on the ban, on the buckle or on
the plating due to wearing or to bad use of the watch;
-Life of the battery in watches with quartz movement;
-Wearing of leather, textile, rubber or stainless steel band.
SWISS MADE WATCHES
3
English User Manual
Descripion of the display and control buttons
Minute hand
Hour hand
Push-button A
Minute counter
Crown
Center stop-second
Push-button B
1/10 second counter

Second hand
Date
Minute counter
Push-button A
Chronograph: Basic function

(Start / Stop / Reset)
Example:
1
Start: Press push-button A.
2
Stop: to stop the timing, press push-buttion
A once more and read the three chronograph
hands: 1h / 20min / 10 sec.
1/10 second counter
Zero positioning:
Press push-button B.
(The three chronograph hands will be reset to
their zero positions)
Push-button B
PROFESSIONAL
RONDA 5040.D
4
English User Manual
Minute counter
Push-button A
Chronograph:
Accumulated timing
Example:
1/10 second counter
Start: (start timing)
Stop: (e.g. 15 m in 5 sec following
Restart: (timing is resumed)
*Stop: (e.g. 13 min 5 sec following

3 )
= 28 min 10 sec
(Tile accumulated measured time is shown)
1 )
5 Reset:
The three chronograph hands are returned to their zero
positions.
Push-button B
Minute counter
Push-button A
1/10 second counter Push-button B
Push-button B
PROFESSIONAL
Please note:
*Following 4 , the accumulation of the timing can be
continued by pressing push-button A
(Restart / Stop, Restart / Stop, ...)
Chronograph:
Intermediate or interval timing
Example:
1 Start: (start timing)
Display interval:
2
e.g. 10 minutes 10 seconds (timing continues in the background)
Making up the measured time:
* 3
(the 3 chronograph hands are quickly
advanced to the ongoing measured time)
4 Stop: (Final time is displayed)
5 Reset:
The 3 chronograph hands are returned to
their zero position
Please note:
*Following 3 . further intervals or intermediates can
be displayed by pressing push-button B (display interval I make up measured time, ...)
RONDA 5040.D
5
English User Manual
Minute counter
Adjusting the chronograph

hands to zero position
Center stop-second
Example:
One or several chronograph hands are not in their correct
zero positions and have to be adjusted (e. g. following a
battery change).
1/10 second counter

Push-button A
Push-button B
Pull out the crown to position Ill (all 3 chronograph

hands are in their correct or incorrect zero position. The display changes from alarm time to reference time)
Keep push-buttons A and B depressed simultaneously for at least 2 seconds (the cent er stop-second rotates by 360 corrective mode is activated).
Adjusting the center stop-second

Single step
A 1 x short
Continuous
A
long
Adjusting the next hand B
Adjusting the 1/10 second counter hand (position 6h)
Single step
A 1 x short
Continuous
A
long
Adjusting the next hand B
Adjusting the minute counter (position 9h)
Single step
A 1 x short
Continuous
A
long
3
PROFESSIONAL
Returning the crown to position I

Termination of the chronograph hands adjustment (can be
carried out at any time)
RONDA 5040.D
6
English User Manual
Second hand Setting the time

1
*Pull out the crown to position III (the watch stops).
Turn the crown until you reach the correct time 8:45.
*Push the crown back into position I.
Please note:
* In order to set the time to the exact second, 1 must
be pulled out when the second hand is in position 60 (I).
Once the hour and minute hands have been set, 3 must
be pushed back into position I at the exact second.
Setting the date (quick mode)
1
3
Pull out the crown to position II (the watch continues

to run).
Turn the crown until the correct date
Push the crown back into position I.
appears.
Please note:
The date can be changed during the date changing
phase between 9:00 PM and 12:00 PM; please note
that the date must be set to the date of the following
day as in this case the automatic date changing does
not occur at midnight.
PROFESSIONAL
RONDA 5040.D
7
English User Manual
Setting the time and date

Example:
-Date / time on the watch: 17 / 1:25 AM
-Present date / time:
04 / 10:39 PM
17
Date
Pull out the crown to position II (watch continues to

run).
Turn the crown until yesterdays date appears
**Pull out the crown to position Ill (the second hand
03
stops. The display changes from alarm lime to reference time.)

04
Date
05
**Turn the crown until the correct date 04 appears.
**Continue to turn the crown until the current time

8:30 PM appears.
05
PROFESSIONAL
**Push the crown back into position I
Please note:
**To set your watch to the exact second, please refer
to the chapter entitled setting the time.
**Please observe the AM/PM clock rhythm.
RONDA 5040.D
Buran SA
Chemin du Val , 2
2900 Porrentruy
Switzerland
Tel. +41 32 466 80 15
Fax. +41 32 466 80 18
e-mail: aviator@aviatorwatch.ch
Copyright 2014
AVIATOR
Printed in Switzerland
SWISS MADE WATCHES

Professional

Uploaded by

Copyright:

Available Formats

Professional

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Professional

Uploaded by

Copyright:

Available Formats

1

english USER MANUAL

SWISS MADE WATCHES

Descripion of the display and control buttons

1/10 second counter

Chronograph: Basic function

1/10 second counter

1/10 second counter

Start: (start timing)

Stop: (e.g. 15 m in 5 sec following

Restart: (timing is resumed)

*Stop: (e.g. 13 min 5 sec following

1/10 second counter Push-button B

Adjusting the chronograph

1/10 second counter

Pull out the crown to position Ill (all 3 chronograph

Adjusting the center stop-second

Returning the crown to position I

Second hand Setting the time

*Pull out the crown to position III (the watch stops).

*Push the crown back into position I.

Setting the date (quick mode)

Pull out the crown to position II (the watch continues

Turn the crown until the correct date

Push the crown back into position I.

Setting the time and date

Pull out the crown to position II (watch continues to

Turn the crown until yesterdays date appears

**Pull out the crown to position Ill (the second hand

stops. The display changes from alarm lime to reference time.)

**Turn the crown until the correct date 04 appears.

**Continue to turn the crown until the current time

**Push the crown back into position I

SWISS MADE WATCHES

You might also like