LM7905,LM7912,LM7915

LM79XX Series 3-Terminal Negative Regulators

Literature Number: SNOSBQ7B

LM79XX Series
3-Terminal Negative Regulators
General Description
The LM79XX series of 3-terminal regulators is available with
fixed output voltages of 5V, 12V, and 15V. These devices
need only one external component a compensation capacitor at the output. The LM79XX series is packaged in the
TO-220 power package and is capable of supplying 1.5A of
output current.
These regulators employ internal current limiting safe area
protection and thermal shutdown for protection against virtually all overload conditions.
Low ground pin current of the LM79XX series allows output
voltage to be easily boosted above the preset value with a

resistor divider. The low quiescent current drain of these

devices with a specified maximum change with line and load
ensures good regulation in the voltage boosted mode.
For applications requiring other voltages, see LM137
datasheet.

Features
n
n
n
n

Thermal, short circuit and safe area protection

High ripple rejection
1.5A output current
4% tolerance on preset output voltage

*Required if regulator is separated from filter capacitor by

more than 3". For value given, capacitor must be solid
tantalum. 25F aluminum electrolytic may be substituted.
Required for stability. For value given, capacitor must be
solid tantalum. 25F aluminum electrolytic may be substituted. Values given may be increased without limit.
For output capacitance in excess of 100F, a high current
diode from input to output (1N4001, etc.) will protect the
regulator from momentary input shorts.

Connection Diagram
TO-220 Package

00734014

Front View
Order Number LM7905CT, LM7912CT or LM7915CT
See NS Package Number TO3B

Typical Applications
Fixed Regulator

00734003

2004 National Semiconductor Corporation

DS007340

www.national.com

LM79XX Series 3-Terminal Negative Regulators

September 2001

LM79XX Series

Absolute Maximum Ratings (Note 1)

(Vo = 5V)

25V

(Vo = 12V and 15V)

30V

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.

Power Dissipation (Note 2)

Input Voltage

Storage Temperature Range

(Vo = 5V)

25V

(Vo = 12V and 15V)

35V

Internally Limited

Operating Junction Temperature Range

0C to +125C
65C to +150C

Lead Temperature (Soldering, 10 sec.)

230C

Input-Output Differential

Electrical Characteristics
Conditions unless otherwise noted: IOUT = 500mA, CIN = 2.2F, COUT = 1F, 0C TJ +125C, Power Dissipation 1.5W.

Symbol
VO

Part Number

LM7905C

Output Voltage

5V

Input Voltage (unless otherwise specified)

10V

Parameter
Output Voltage

Conditions

Min

Typ

Max

TJ = 25C

4.8

5.0

5.2

5mA IOUT 1A,

4.75

5.25

50

mV

15

mV

P 15W
VO

Line Regulation

Units

(20 VIN 7)

TJ = 25C, (Note 3)

8
(25 VIN 7)

2
(12 VIN 8)
VO

Load Regulation

TJ = 25C, (Note 3)
5mA IOUT 1.5A

15

100

mV

250mA IOUT 750mA

50

mV

IQ

Quiescent Current

TJ = 25C

mA

IQ

Quiescent Current

With Line

0.5

mA

0.5

mA

(25 VIN 7)

Change

With Load, 5mA IOUT 1A

Vn

IOMAX

Output Noise Voltage

TA = 25C, 10Hz f 100Hz

Ripple Rejection

f = 120Hz

Dropout Voltage

TJ = 25C, IOUT = 1A

1.1

Peak Output Current

TJ = 25C

2.2

Average Temperature

IOUT = 5mA,

0.4

mV/C

Coefficient of

0 C TJ 100C

125

66

dB

(18 VIN 8)

54

Output Voltage

Electrical Characteristics
Conditions unless otherwise noted: IOUT = 500mA, CIN = 2.2F, COUT = 1F, 0C TJ +125C, Power Dissipation 1.5W.
Part Number

LM7912C

LM7915C

Output Voltage

12V

15V

Input Voltage (unless otherwise specified)

Symbol
VO

Parameter
Output Voltage

19V

Conditions

Min

Line Regulation

23V
Max

TJ = 25C

11.5 12.0 12.5

5mA IOUT 1A,

11.4

P 15W
VO

Typ

TJ = 25C, (Note 3)

Min

Typ

Max

14.4

15.0

15.6

15.75

12.6 14.25

(27 VIN 14.5)

(30 VIN 17.5)

mV

80

100

(30 VIN 14.5)

(30 VIN 17.5)

mV

30

(22 VIN 16)

www.national.com

Units

50

(26 VIN 20)

(Continued)
Conditions unless otherwise noted: IOUT = 500mA, CIN = 2.2F, COUT = 1F, 0C TJ +125C, Power Dissipation 1.5W.
Part Number

LM7912C

LM7915C

Output Voltage

12V

15V

Input Voltage (unless otherwise specified)

Symbol
VO

Parameter

19V

Conditions

Load Regulation

Min

Max

5mA IOUT 1.5A

15

250mA IOUT 750mA

Min

Typ

Max

200

15

200

mV

75

75

mV

1.5

TJ = 25C, (Note 3)

IQ

Quiescent Current

TJ = 25C

Quiescent Current

With Line

1.5

Change

mA

0.5

0.5

mA

(30 VIN 14.5)

(30 VIN 17.5)

With Load, 5mA IOUT 1A

IOMAX

23V

Typ

IQ

Vn

Units

Output Noise Voltage

TA = 25C, 10Hz f 100Hz

Ripple Rejection

f = 120 Hz

0.5

0.5

300

V
mA

375

70

dB

(25 VIN 15)

(30 VIN 17.5)

V
V

54

70

54

Dropout Voltage

TJ = 25C, IOUT = 1A

1.1

1.1

Peak Output Current

TJ = 25C

2.2

2.2

Average Temperature

IOUT = 5mA,

0.8

1.0

mV/C

Coefficient of

0 C TJ 100C

Output Voltage
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but do not guarantee Specific Performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: Refer to Typical Performance Characteristics and Design Considerations for details.
Note 3: Regulation is measured at a constant junction temperature by pulse testing with a low duty cycle. Changes in output voltage due to heating effects must
be taken into account.

Solving for TJ:

TJ = TA + PD (JC + CA) or
= TA + PDJA (without heat sink)
Where:
TJ = Junction Temperature
TA = Ambient Temperature
PD = Power Dissipation

Design Considerations
The LM79XX fixed voltage regulator series has thermal
overload protection from excessive power dissipation, internal short circuit protection which limits the circuits maximum
current, and output transistor safe-area compensation for
reducing the output current as the voltage across the pass
transistor is increased.
Although the internal power dissipation is limited, the junction temperature must be kept below the maximum specified
temperature (125C) in order to meet data sheet specifications. To calculate the maximum junction temperature or
heat sink required, the following thermal resistance values
should be used:

Package
TO-220

Typ

Max

Typ

JC

JC

JA

JA

C/W

C/W

C/W

C/W

3.0

5.0

60

40

JA
JC
CA
CS

= Junction-to-Ambient Thermal Resistance

= Junction-to-Case Thermal Resistance
= Case-to-Ambient Thermal Resistance

= Case-to-Heat Sink Thermal Resistance

SA = Heat Sink-to-Ambient Thermal Resistance

Max

www.national.com

LM79XX Series

Electrical Characteristics

LM79XX Series

high frequency characteristics. If aluminum electrolytics are

used, their values should be 10F or larger. The bypass
capacitors should be mounted with the shortest leads, and if
possible, directly across the regulator terminals.

Typical Applications
Bypass capacitors are necessary for stable operation of the
LM79XX series of regulators over the input voltage and
output current ranges. Output bypass capacitors will improve
the transient response by the regulator.
The bypass capacitors, (2.2F on the input, 1.0F on the
output) should be ceramic or solid tantalum which have good

High Stability 1 Amp Regulator

00734005

Load and line regulation < 0.01% temperature stability 0.2%

Determine Zener current
Solid tantalum

*Select resistors to set output voltage. 2 ppm/C tracking suggested

Current Source

00734007

www.national.com

LM79XX Series

Typical Applications

(Continued)
Light Controller Using Silicon Photo Cell

00734008

*Lamp brightness increase until iI= iQ ( 1 mA) + 5V/R1.

Necessary only if raw supply filter capacitor is more that 2" from LM7905CT

High-Sensitivity Light Controller

00734009

*Lamp brightness increases until ii = 5V/R1 (Ii can be set as low as 1 A)

Necessary only if raw supply filter capacitor is more that 2" from LM7905

Variable Output

00734002

*Improves transient response and ripple rejection. Do not increase beyond 50 F.

Select R2 as follows:
LM7905CT

300

LM7912CT

750

LM7915CT

1k

www.national.com

LM79XX Series

Typical Applications

(Continued)

15V, 1 Amp Tracking Regulators

00734001

(-15)

(+15)

Load Regulation at IL = 1A

40mV

2mV

Output Ripple, CIN = 3000F, IL = 1A

100 Vms

100 Vms

Temperature Stability

50mV

50mV

Output Noise 10Hz f 10kHz

150 Vms

150 Vms

*Resistor tolerance of R4 and R5 determine matching of (+) and () outputs.

**Necessary only if raw supply filter capacitors are more than 3" from regulators.
Dual Trimmed Supply

00734004

www.national.com

LM79XX Series

Schematic Diagrams
5V

00734012

12V and 15V

00734013

www.national.com

LM79XX Series 3-Terminal Negative Regulators

Physical Dimensions

inches (millimeters)

unless otherwise noted

TO-220 Outline Package (T)

Order Number LM7905CT, LM7912CT or LM7915CT
NS Package Number T03B

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONALS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.

2. A critical component is any component of a life support

device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.

BANNED SUBSTANCE COMPLIANCE

National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship
Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no Banned
Substances as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
www.national.com

National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Franais Tel: +33 (0) 1 41 91 8790

National Semiconductor
Asia Pacific Customer
Support Center
Email: ap.support@nsc.com

National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560

IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products

Applications

Audio

www.ti.com/audio

Communications and Telecom www.ti.com/communications

Amplifiers

amplifier.ti.com

Computers and Peripherals

www.ti.com/computers

Data Converters

dataconverter.ti.com

Consumer Electronics

www.ti.com/consumer-apps

DLP Products

www.dlp.com

Energy and Lighting

www.ti.com/energy

DSP

dsp.ti.com

Industrial

www.ti.com/industrial

Clocks and Timers

www.ti.com/clocks

Medical

www.ti.com/medical

Interface

interface.ti.com

Security

www.ti.com/security

Logic

logic.ti.com

Space, Avionics and Defense

www.ti.com/space-avionics-defense

Power Mgmt

power.ti.com

Transportation and Automotive www.ti.com/automotive

Microcontrollers

microcontroller.ti.com

Video and Imaging

RFID

www.ti-rfid.com

OMAP Mobile Processors

www.ti.com/omap

Wireless Connectivity

www.ti.com/wirelessconnectivity
TI E2E Community Home Page

www.ti.com/video

e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright 2011, Texas Instruments Incorporated