125pf e

July.
13, 2009
Oscillator frequency calibration with CL=12.5pF crystal and Ricoh RTC IC

Ricoh recommends to use CL=6pF to 8pF crystal with our RTC. On the other hand, some
crystal vendors offer CL=12.5pF crystal as their standard crystal. This document explains how
to use CL=12.5pF crystal with Ricohs RTC for its oscillator frequency calibration.
Items are as follows:
Ricoh RTC lineup which is applied to this document
What is the load capacitance of a crystal (CL)?
The effect of using CL=12.5pF crystal with Ricohs RTC
How to adjust the clock frequency with the calibration function of Ricoh RTC
How to evaluate the clock gain or loss
Notes on using the oscillator calibration circuit
< Ricoh RTC lineup which is applied to this document >
This document is applied to the following Ricoh RTC lineup:
Table 1: The RTC applied to this document
SSOP8
SSOP10
SSOP10G
TSSOP10G
FFP12
SSOP16
SPI
RS5C348A/B RV5C348A/B RT5C348B R2043K
(4 wire)
R2043T
3 wire
RS5C338A
RV5C338A
R2033T
R2061Kxx R2061Sxx
RV5C339A
R2062Kxx
R2033K
I2C Bus RS5C372A/B
RV5C386A
R2051T01 R2051Kxx R2051Sxx
RV5C387A
R2023T
R2023K
< What is the load capacitance of a crystal (CL)? >
Fig. 1 shows the typical oscillator circuit of CMOS clock IC. The load capacitance (CL) of the
crystal is a critical parameter. The CL is not the capacitance of the crystal itself.
VDD
VDD
OSCIN
CG
RF
RD
CS
CD
32768Hz
Crystal
CS: Stray Capacitance
OSCOUT
Fig.1: Typical Oscillation Circuit
When CS+CGCD/(CG+CD) is equal to CL, the crystal oscillates at its nominal frequency
(32768Hz).
When CS+CGCD/(CG+CD) is bigger than CL, the crystal oscillates slower than 32768Hz.
And, when CS+CGCD/(CG+CD) is smaller than CL, the crystal oscillates faster than 32768Hz.
1/4
< The effect of using CL=12.5pF crystal with Ricohs RTC>

The Ricohs RTC ICs on the Table 1 incorporate CG and CD. These values are calculated and
designed for CL=6 to 8pF crystal.
VDD
CGin
VDD
OSCIN
Oscillation
CGin,CDin 12pF(Typ.)
CS
Circuit
RD
CDin
OSCOUT
32768Hz
Crystal(CL=6 to 8pF)
Fig.2: Oscillation Circuit for Ricohs RTC

When we use 12.5pF crystal, and if CGout=CDout=12pF are added as in Fig 3, output
frequency will be 32768Hz as in the previous formula. (CS=0.5pF)
VDD
VDD
CGin,CDin 12pF(Typ.)
CGin
OSCIN
Oscillation
CGout,CDout 12pF
CGout
CDout
Circuit
RD
CDin
CS
CS 0.5pF
32768Hz
Crystal (CL=12.5pF)
OSCOUT
Fig.3: Oscillation Circuit for Ricohs RTC and 12.5pF crystal

Experimented data for RV5C338A on this circuit is as follows:
Table 2: Characteristics for the circuit in Fig3
VDD=3v, Ta=25C, Crystal is MS2V-TS (CL=12.5pF) (Micro Crystal)
CGout=CDout=0pF
CGout=CDout=12pF
(without using CGout and
(with using CGout and
CDout)
CDout)
Frequency
32770.49Hz
32767.96Hz
Oscillation
Frequency
+75.99ppm
-1.22ppm
deviation
(gains 204sec a month)
(loses 3.3sec a month)
(32768Hz as standard)
Time keeping current
0.35A
0.53A
Minimum
time
keeping
0.90v
1.04v
voltage
Negative Resistance
-719k
-164k
Oscillation allowance
11.4 times
3.4 times
If 12.5pF crystal is used with CGout and CDout, our RTC oscillates at its very close frequency
to the specified value.
2/4
But power consumption increases from 0.35A to 0.53A, minimum time keeping voltage
decreases, oscillation negative resistance is worse, and oscillator margin decreases.
Most of crystal manufacturers recommend users to make the negative resistance of the
oscillation circuit bigger enough against the equivalent series resistor of the crystal. Oscillator
margin means the equivalent series resistor of the crystal (Refer to the specifications of the
crystal.) plus negative resistance, and the sum divides by the equivalent series resistor.
Generally it is 5.0times or more. If oscillation margin is around 3.4 times, this oscillator will
oscillate in normal condition, but may halt under bad conditions such as low temperature. The
definition of negative resistance and its measurement method are also written in the catalogs of
the crystals. Ricoh recommends to use CGout<15pF and CDout=0pF.
< How to adjust the clock frequency with software calibration of Ricoh RTC>
If 12.5pF crystal is used without CGout and CDout, Ricohs RTC will run approximately 80ppm
faster than normal use, that is, 210sec every month. But Ricohs RTC incorporates the clock
adjustment circuit. To correct time error in the oscillation frequency of the crystal oscillator, the
oscillation adjustment circuit is configured to allow correction of a time count gain or loss from
the CPU within a maximum range of 189ppm. The oscillation adjustment circuit can adjust
80ppm-gain clock used even if 12.5pF crystal is used for precision clock.
To correct time count gain, write the oscillation adjustment value calculated with the next
formula to the oscillation adjustment register.
Oscillation adjustment value = (oscillator frequency target frequency) 10 + 1
Generally, the temperature characteristics of the 32768Hz crystal oscillator describe a parabola
of which peak is at 25C. Therefore, to obtain the accurate clock under the average temperature,
rather higher target frequency may be appropriate. (+1 to 6ppm higher than 32768Hz).
For example, in the Table 2, oscillator frequency is 32770.49Hz (CGout=CDout=0pF). When the
desired frequency is 32768.05Hz, the oscillation adjustment value is (32770.49-32768.05) 10
+ 1 = 25.4 25. 25 is described 19h in hexadecimal numeral. (00011001) shall be
written to address 7h.
< How to evaluate the clock gain or loss>
The oscillator adjustment circuit is configured to change time counts of 1 second on the basis of
the settings of the oscillation adjustment register once in 20seconds. The oscillation adjustment
circuit does not effect the frequency of 32768Hz-clock pulse output from the 32KOUT
(CLKOUT) pin. Therefore, after writing the oscillation adjustment register, we cannot measure
the clock error with probing 32KOUT (CLKOUT) clock pulses. The way to measure the clock
error as follows:
(1) Output a 1Hz clock pulse of Pulse Mode with interrupt pin
Each RTC has different 1Hz output pin and the way to set the register.
Table 3: 1Hz output pin and the way to set the register for output 1Hz clock
Setting
Output Pin
RS5C372A
/INTRA(5pin)
Address Eh (00000011)
RS5C372B
/INTR(5pin)
RS/RV5C338A
/INTR(6pin)
Address Eh (00XX0011)
RV5C339A
/INTRA(6pin)
RS/RV/RT5C348A/B, R2043T
/INTR(6pin)
RV5C386A/387A,R2023T
/INTRA(6pin)
R2043K,R2033K
/INTR(10pin)
R2023K
/INTRA(10pin)
R2051Kxx,R2061Kxx, R2062Kxx
/INTR(9pin)
/INTR(10pin)
R2051Sxx,R2061Sxx
3/4
(2) After setting the oscillation adjustment register, 1Hz clock period changes every 20seconds
like Fig. 4.
1Hz clock pulse
T0
T0
T0
19 times
T1
1 time
Fig.4
Measure the interval of T0 and T1 with frequency counter.
digits is recommended for the measurement.
A frequency counter with 7 or more
(3) Calculate the typical period from T0 and T1

T = (19T0+1T1)/20
Calculate the time error from T.
Example: The time error for previous example. When oscillation frequency is 32770.49Hz and
19h is set as the oscillator calibration value, T0 is 0.99992402s and T1 is 1.00138875s.
Then, T = (190.99992402+11.00138875)/20 = 0.99999726.
Time error/day = (0.99999726-1)60seconds60minutes24hours = -0.24sec/day.
We set the oscillation adjustment register to run clock just a little faster than nominal with
considering crystal temperature characteristics. As a result, the actual time error is a little fast.
< Notes on using the oscillator calibration circuit>
When using the oscillator calibration circuit,
(1) Ricohs RTC does not have non-volatile memory. Therefore, the system must store the
oscillator adjustment value to non-volatile memory external of the RTC. The system must write
the oscillation adjustment value to RTC, when setting the clock and calendar data.
(2) The oscillation adjustment circuit does not affect the frequency of 32768Hz-clock pulse
output from the 32KOUT (CLKOUT) pin. If the frequency of clock pulse from 32KOUT
(CLKOUT) pin should be accurate, change the 12.5pF crystal to a 6pF crystal.
(3) If following 3 conditions are completed, actual clock adjustment value could be different from
target adjustment value that set by oscillator adjustment function.
1. Using oscillator adjustment function
2. Access to RTC at random, or synchronized with external clock that has no relation to RTC, or
synchronized with periodic interrupt in pulse mode.
3. Access to RTC more than 2 times per each second on average.
For more details, please contact to Ricoh.
4/4

125pf e

Uploaded by

Copyright:

Available Formats

125pf e

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

125pf e

Uploaded by

Copyright:

Available Formats

July.

Oscillator frequency calibration with CL=12.5pF crystal and Ricoh RTC IC

Fig.1: Typical Oscillation Circuit

< The effect of using CL=12.5pF crystal with Ricohs RTC>

Fig.2: Oscillation Circuit for Ricohs RTC

Fig.3: Oscillation Circuit for Ricohs RTC and 12.5pF crystal

A frequency counter with 7 or more

(3) Calculate the typical period from T0 and T1

You might also like