3800 Appendices

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.
com
Parker Fluid Connectors Group

North American Divisions & Distribution Service Centers
Hose, Tubing and Bundles:

Available in a wide variety of
sizes and materials including
rubber, wire-reinforced,
thermoplastic, hybrid and
custom compounds.
Worldwide Availability:
Parker operates Fluid
Connectors manufacturing
locations and sales offices
throughout North America,
South America, Europe and
Asia-Pacific.
For information, call toll free...
1-800-C-PARKER
(1-800-272-7537)
Distribution Service Centers
Energy Products Division

Stafford, TX
phone 281 566 4500
fax 281 530 5353
Buena Park, CA
phone 714 522 8840
fax 714 994 1183
Fluid System Connectors

Division
Otsego, MI
phone 269 694 9411
fax 269 694 4614
Hose Products Division
Wickliffe, OH
phone 440 943 5700
fax 440 943 3129
Industrial Hose Division
Wickliffe, OH
phone 440 833 2173
fax 440 833 2122
Parflex Division
Ravenna, OH
phone 330 296 2871
fax 330 296 8433
Quick Coupling Division
Minneapolis, MN
phone 763 544 7781
fax 763 544 3418
Conyers, GA
phone 770 929 0330
fax 770 929 0230
Louisville, KY
phone 502 937 1322
fax 502 937 4180
Portland, OR
phone 503 283 1020
fax 503 283 2201
Toledo, OH
phone 419 878 7000
fax 419 878 7001
fax 419 878 7420
(FCG Kit Operations)
Canada
Grimsby, ONT
phone 905 945 2274
fax 905 945 3945
(Contact Grimsby for other
Service Center locations)
Quick Coupling Products
Fittings:
Available in inch and metric
sizes covering SAE, BSP,
DIN, GAZ, JIS and ISO thread
configurations, manufactured
from steel, stainless steel,
brass, aluminum, nylon and
thermoplastic.
North American Divisions
Catalog 3800
Your complete source for

quality tube fittings, hose & hose
fittings, brass & composite
fittings, quick disconnect
couplings, valves and assembly
tools, locally available from a
worldwide network of authorized
distributors.
Tube Fittings Division

Columbus, OH
phone 614 279 7070
fax 614 279 7685
Catalog 3800 /USA 19M 02/14 QCD AP
Parker Hannifin Corporation

8145 Lewis Road
Minneapolis, MN 55427
phone 763 544 7781
fax 763 544 3418
www.parker.com/quickcouplings
February 2014
2014 Parker Hannifin Corporation

Quick Couplings, Swivels, Valves,
Diagnostic Equipment
Catalog 3800 USA | February 2014
Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.com
Quick Coupling Division Locations
About Parker Hannifin Corporation

Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. A Fortune 500
corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that
control motion in some 1,000 industrial and aerospace markets. Parker is the only manufacturer to 7,500 distributors serving
nearly 400,000 customers worldwide.
Parkers Charter
Minneapolis, MN
Grantsburg, WI
To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. More
specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve
profitable growth through premier customer service.
Product Information
North American customers seeking product information, the location of a nearby distributor, or repair services will receive
prompt attention by calling the Parker Product Information Center at our toll-free number: 1-800-C-PARKER (1-800-272-7537).
In Europe, call: 00800-C-PARKER-H (00800-2727-5374).
Chetek, WI
Union City, PA
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS
CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors
provide product or system options for further investigation by users having technical expertise.
The user, through its own analysis and testing, is solely responsible for making the final selection of the system and
components and assuring that all performance, endurance, maintenance, safety and warning requirements of the
application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow
the information concerning the product in the current product catalog and in any other materials provided from Parker or
its subsidiaries or authorized distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon
data or specifications provided by the user, the user is responsible for determining that such data and specifications are
suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.
Offer of Sale
The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its
authorized distributors. This offer and its acceptance are governed by the provisions stated in the Offer of Sale.
2014, Revised Feb 2014, Parker Hannifin Corporation, All Rights Reserved.
The Aerospace Group is a

leader in the development,
design, manufacture and
servicing of control systems
and components for aerospace
and related high-technology
markets, while achieving
growth through premier
customer service.
The Climate & Industrial

Controls Group designs,
manufactures and markets
system-control and fluidhandling components and
systems to refrigeration,
air-conditioning and industrial
customers worldwide.
The Fluid Connectors Group

designs, manufactures and
markets rigid and flexible
connectors, and associated
products used in pneumatic
and fluid systems.
The Seal Group designs,

manufactures and distributes
industrial and commercial
sealing devices and related
products by providing
superior quality and total
customer satisfaction.
The Hydraulics Group designs,

produces and markets a
full spectrum of hydraulic
components and systems
to builders and users of
industrial and mobile
machinery and equipment.
The Filtration Group designs,

quality filtration and
clarification products,
providing customers with
the best value, quality,
technical support, and
global availability.
The Automation Group is

a leading supplier of pneumatic
and electromechanical
to automation customers
worldwide.
The Instrumentation Group

is a global leader in the design,
manufacture and distribution
of high-quality critical flow
components for worldwide
process instrumentation,
ultra-high-purity, medical
and analytical applications.
Table of Contents
Pneumatic Quick Couplings.................................Section

Hydraulic Quick Couplings.................................Section

Thermoplastic Couplings.. ........................................Section
Swivels.. ...................................................................Section
A
B
C
D
Valves....................................................................Section E
Diagnostic Products..............................................Section F

Appendices:
Fluid Compatibility Chart........................................................I
Safety Guide....................................................................VI
Offer of Sale.................................................................IX
Glossary of Terms.............................................................X

Minneapolis, MN
Fluid Compatibility Chart........................................................I

Safety Guide...................................................................VII
Offer of Sale.................................................................IX
Appendices
F Diagnostic
E Valves
D Swivels
Glossary of Terms...............................................................X
C Thermoplastics
Appendices
B Hydraulics
A Pneumatics
F-33

Minneapolis, MN
Appendix
Fluid Compatibility Chart
Codes
For recommendations for media not listed below, please
contact your Parker representative or the factory.
The following seal compound and body material

compatibility chart is provided as an aid in selecting a
specific synthetic rubber compound or body material for
a particular application. Operating and environmental
conditions must be considered when making the
selection of a quick coupling.
Refer to the appropriate section of the catalog for
Ordering Information for Seal Codes for specific
products.
To indicate a special material just add the appropriate
code letter as a suffix to the catalog number of the
coupler.
It is not necessary to use the code STD as the standard
Nitrile seal will be used when another code is not used.
Note
This chart is intended as a guide only and is not be
considered as a recommendation to use Parker quick
action couplings in a specific application or with a
specific fluid, other factors that must be considered
include but are not limited to: fluid and ambient
temperature, system pressure, both operating and peak,
frequency of connect and disconnect, and applicable
standards or regulations.
CODES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient Data Available
3M FC-75
ACETAMIDE
ACETIC ACID (5%)
ACETONE
ACETOPHENONE
ACETYL ACETONE
ACETYL CHLORIDE
ACETYLENE
AIR (200 DEGREES F.)
ALUMINUM ACETATE
ALUMINUM BROMIDE
ALUMINUM CHLORIDE (10%)
ALUMINUM CHLORIDE (100%)
ALUMINUM FLOURIDE
ALUMINUM NITRATE
ALUMINUM SALTS
ALUMINUM SULPHATE
ALUMS (NH3,Cr,K)
AMMONIA (ANHYDROUS)
AMMONIA (COLD, GAS)
AMMONIA (HOT, GAS)
AMMONIUM CARBONATE
AMMONIUM CHLORIDE
AMMONIUM HYDROXIDE
AMMONIUM NITRATE
AMMONIUM PERSULFATE SOLUTION
AMMONIUM PHOSPHATE
(MONO-, DI-, TRI-BASIC)
AMMONIUM SALTS
AMMONIUM SULFATE
AMYL BORATE
AMYL CHLORIDE
AMYL CHLORONAPHTHALENE
AMYL NAPHTHALENE
ANIMAL OIL (LARD OIL)
AROCLOR 1248
AROCLOR 1254
AROCLOR 1260
AROMATIC FUEL (50%)
ARSENIC ACID
ASPHALT
ASTM OIL, NO. 1
ASTM OIL, NO. 2
BODY MATERIAL SEAL MATERIAL

Brass Steel 316 S.S. 303 S.S.
Nitrile E.P. Fluorocarbon Neoprene
4
4 4 4
4
4 1 2
3
3
1
1
1
2 1 1
2
2 2 1
2
2 2 2
4
2 2 2
3
2 1 1
1
2
1
1
1
2
1
1
1
2
1
1
4
4 4 4
4
4 4 4
3
3
3
3
3
2
2
2
3
3 3 3
3
3 2 2
4
4 4 4
2
3 2 3
4
4 4 4
3
2 1 1
3
2
4
1
3
2
4
1
3
2 3 3
3
3 2 3
3
3 1 2
3
3 1 1
3
3
1
2
1
1
1
1
2
1
3
1
3
1
3
1
3
3
1
1
1
1
2
2
3
3
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
2
3
1
1
1
3
1
1
1
3
1
2
3
1
3
3
3
1
1
1
1
1
3
1
1
1
1
1
1
1
3
3
3
3
1
1
3
4
4
1
1
1
3
3
3
3
2
1
2
3
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
4
3
3
3
2
4
4 4 4
3
3 2 3
4
4 4 4
4
2 1 1
4
4 4 4
4
4 4 4
2
2
2
2
2
3 3 3
2
3 3 3
2
3 3 3
4
4
4
4
3
3 1 1
3
3 1 1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
4
3
3
3
3
3
1
2
3
2
3
2
1
4
2
3
1
1
2
3
1
3
1
3
4
3
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
3
3
2
3
3
1
3
1
2
1
2

Minneapolis, MN
Appendices

MEDIA
Appendix
Appendices

MEDIA
ASTM OIL, NO. 3
ASTM OIL, NO. 4
ASTM REFERENCE FUEL A
ASTM REFERENCE FUEL B
ASTM REFERENCE FUEL C
AUTOMOTIVE BRAKE FLUID
BARIUM CHLORIDE
BARIUM HYDROXIDE
BARIUM SALTS
BARIUM SULFIDE
BEER
BEET SUGAR LIQUORS
BENZALDEHYDE
BENZENE
BENZENESULFONIC ACID (10%)
BENZINE
BENZOIC ACID
BENZYL ALCOHOL
BENZYL CHLORIDE
BLEACH LIQUOR
BORAX
BORDEAUX MIXTURE
BORIC ACID
BRAKE FLUID (NON-PETROLEUM)
BRINE (SODIUM CHLORIDE)
BROMINE
BROMINE WATER
BUNKER OIL
BUTADIENE (MONOMER)
BUTANE
BUTANE (2,2, & 2,3-DIMETHYL)
BUTANOL (BUTYL ALCOHOL)
BUTTER - ANIMAL FAT
BUTYL BUTYRATE
BUTYL STEARATE
CALCINE LIQUORS
CALCIUM ACETATE
CALCIUM BISULFITE
CALCIUM CARBONATE
CALCIUM CHLORIDE
CALCIUM HYDROXIDE
CALCIUM HYPOCHLORITE
CALCIUM SALTS
CALCIUM SULFIDE
CALICHE LIQUORS
CANE SUGAR LIQUORS
CARBON BISULPHIDE
CARBON DIOXIDE
CARBON DISULFIDE
CARBON MONOXIDE
CARBON TETRACHLORIDE
CARBONIC ACID
CASTOR OIL
CELLUGUARD
CELLULUBE (NOW FYRQUEL)
CHINA WOOD OIL (TUNG OIL)
CHLORINATED SALT BRINE
CHLORINATED SOLVENTS
CHLOROBENZENE
CHLOROBUTADIENE
CHLOROFORM
CHLORPHENOL
COCONUT OIL
COPPER CHLORIDE
COPPER SALTS
COPPER SULFATE
1
1
1
1
1
1
1
1
3
2
1
1
3
2
1
1
3
2
1
1
4
4
4
4
3
3 2 3
3
2 2 3
4
4 4 4
3
2 3 3
3
3 1 1
3
3
1
1
3
3 2 3
3
2 3 3
3
3
3
3
4
4 4 4
3
3 3 3
4
3 1 2
3
3 2 3
4
4 4 4
3
2 3 3
4
4 4 4
3
3 2 3
4
4
4
4
3
3
1
1
4
4 4 4
4
4 4 4
4
4 4 4
3
2 1 2
3
1 1 1
4
4
4
4
2
1
1
1
2
3
1
2
4
4 4 4
4
4 4 4
4
4 4 4
4
4 4 4
3
3 2 3
3
2 3 2
3
3 2 3
3
3 2 3
3
3 2 3
4
4 4 4
3
3 2 2
4
4 4 4
4
2
1
1
4
4 4 4
1
2 1 1
2
2 2 2
1
1 1 1
2
3 1 3
3
3 1 2
1
1 1 1
4
4 4 4
4
4
4
4
2
2
1
1
4
4
4
4
4
4 4 4
3
3 2 3
4
4 4 4
3
2 2 1
4
4 4 4
4
4 4 4
4
4 4 4
4
4 4 4
3
3 2 3
II
1
3
2
3
1
3
1
3
2
3
3
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
3
3
3
3
1
3
3
3
3
2
3
3
3
1
2
1
2
1
1
1
3
1
1
1
3
3
3
2
1
3
3
3
1
3
1
3
1
2
1
1
3
1
2
3
1
1
2
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
3
3
1
1
3
3
1
1
2
3
2
1
1
2
1
1
3
1
1
3
3
3
3
3
3
3
3
3
3
3
3
3
1
3
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
3
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
3
2
3
3
2
1
1
1
1
1
2
3
3
2
2
3
2
3
2
3
2
1
2
1
3
3
3
3
1
2
1
2
3
3
4
2
2
1
1
1
2
1
1
1
1
3
1
3
2
3
1
1
1
3
2
3
3
3
3
3
3
3
2
1
1

Minneapolis, MN
Appendix
CORN OIL
COTTONSEED OIL
CREOSOLS
CREOSOTE
CRESYLIC ACID
CRUDE OIL
CUTTING OIL
DECANE
DENATURED ALCOHOL
DETERGENT, WATER SOLUTION
DIESEL FUEL
DIETHYLENE GLYCOL
DIMETHYL FORMAMIDE
DOW CHEMICAL HD50-4
DOW CORNING 200, 510, 550
DOWTHERM A,E
ETHANOL
ETHYL CHLORIDE
ETHYL HEXANOL
ETHYLENE DICHLORIDE
ETHYLENE GLYCOL
FATTY ACIDS
FREON 11
FREON 12
FREON 22
FREON 134a
FUEL OIL
GALLIC ACID
GAS, LIQUID, PROPANE (LPG)
GAS, NATURAL
GASOLINE
GELATIN
GLUCOSE
GLYCERINE (GLYCEROL)
GLYCOLS
GREEN SULFATE LIQUOR
GULF - FR FLUID (EMULSION)
GULF - FR FLUID G
GULF - FR FLUID P
HELIUM
HEPTANE
HYDRAULIC OIL (PETROLEUM BASE)
HYDRAULIC OIL (WATER BASE)
HYDRAZINE
HYDROGEN GAS
HYDROLUBE
ISO OCTANE
ISOBUTYL ALCOHOL
ISOPROPYL ALCOHOL
ISOPROPYL ETHER
JP3 AND JP4
KEROSENE
LARD, ANIMAL FAT
LINSEED OIL
LUBRICATING OIL SAE 10, 20, 30, 40, 50
MAGNESIUM SALTS
MAGNESIUM SULPHATE
MERCURY
METHANE
METHANOL
METHYL BROMIDE
METHYL CHLORIDE (DRY)
METHYL CHLORIDE (WET)
METHYL ETHER
METHYL ETHYL KETONE (MEK)
MIL-F-81912 (JP-9)

Brass

Steel 316 S.S. 303 S.S.
2
1 1 1
3
2 1 2
3
2 1 2
3
3 2 1
4
2 1 2
3
2 1 1
4
1 1 1
4
4 4 4
4
4 4 4
3
3
1
1
1
1 1 1
3
1 1 1
4
4 1 1
4
4
4
4
4
4
4
4
3
1 2 2
1
3 3 3
2
3 1 3
4
4 4 4
3
3 1 2
2
2 1 2
3
3 1 2
1
4 4 4
1
1 3 1
1
3 1 1
1
1 1 1
3
1 1 1
3
3 2 2
1
3
1
1
2
3 1 1
1
2 1 1
3
3 1 1
1
1 1 1
2
1 1 1
3
2 2 2
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
1
1 1 1
1
1 1 1
1
1
1
1
4
1
1
1
4
3 1 1
2
2 1 1
4
4 4 4
1
1 1 1
4
4 1 1
1
1 2 1
1
1 1 1
1
1
1
1
1
1 1 1
1
1
1
1
3
1 1 1
1
1
1
1
4
4 4 4
3
3 2 2
3
3 1 1
1
3 1 1
1
1 1 1
4
1 1 1
2
3
1
1
1
3
1
3
4
4 4 4
1
1
1
1
1
1 1 1
III
1
3 1
1
3 1
3
3 1
1
3 1
3
3 1
2
3 1
1
3 1
1
3 1
1
1 1
1
1
1
1
3 1
1
1 1
2
1 3
4
1
3
2
1
1
3
3 1
3
1 3
1
3 1
1
1 1
3
3 1
1
1 1
2
3 1
2
3 2
2
3 1
3
3 3
2
1 4
1
3 1
2
2 1
1
3
1
1
3 1
3
3 1
1
1 1
1
1 1
1
1 1
1
1 3
2
1
1
1
3
1
1
1
1
3
2
2
1
1 1
1
3 1
1
3
1
2
1
3
2
1 3
1
1 1
1
1 1
1
3 1
2
1 1
2
1 1
2
3 3
1
3
1
1
3 1
1
2
1
1
3 1
1
3
1
1
1 1
1
1 1
1
1 1
1
3 1
1
1 3
2
3 1
3
3
1
3
3
1
1
3 1
3
1
3
3
3 1
3
3
3
2
3
3
2
3
1
2
3
1
3
2
1
3
1
3
1
3
1
2
3
1
1
1
2
2
2
1
3
1
1
1
1
2
2
1
3
1
2
1
2
2
1
2
2
1
2
3
3
2
2
3
2
1
1
1
2
1
3
3
3
3
3
3

Minneapolis, MN
Appendices

MEDIA
Appendix
Appendices

MEDIA

Nitrile
E.P. Fluorocarbon Neoprene
MIL-H-5606
1
1 1 1
MIL-H-6083
1
1 1 1
MIL-H-7083
1
1 1 1
2
1 1 1
MIL-H-8446 (MLO-8515)
MIL-L-2104 & 2104B
1
1 1 1
3
2 1 1
MIL-L-7808
MILK
2
1 1 1
MINERAL OILS
1
1 1 1
2
1 1 1
MLO-7277 AND MLO-7557
MOBILE HF
1
1 1 1
4
4 4 4
MONOMETHYL HYDRAZINE
NAPHTHA (COAL OR PETROLEUM)
2
1 2 2
NAPHTHALENE
2
1 2 2
2
1 2 2
NAPHTHENIC ACID
NEATSFOOT OIL
4
4 4 4
3
2 1 1
NICKEL, ACETATE
NICKEL CHLORIDE
3
3 2 2
NICKEL SALTS
4
4 4 4
NICKEL SULFATE
3
3 1 1
NITROGEN
1
1 1 1
NITROUS OXIDE
2
2 2 1
OCTYL ALCOHOL
1
1 1 1
OLIVE OIL
2
1 1 1
ORTHO-DICHLOROBENZENE
2
2 2 2
OXALIC ACID
3
3 2 1
OXYGEN (200-400 DEGREES F.)
1
1 1 1
OXYGEN, COLD
1
1 1 1
OZONE
3
3 1 1
PALMITIC ACID
1
2 1 1
PARA-DICHLOROBENZENE
2
1 1 2
1
1 1 1
PARKER O LUBE
PEANUT OIL
2
1 1 1
2
2
2
2
PENTANE (2-3-METHYL, & 2-4 DIMETHYL)
PERCHLORIC ACID -2N
3
3 2 2
PERCHLOROETHYLENE
3
2 2 2
PETROLATUM
1
1 1 1
PETROLEUM OIL, BELOW 250 DEGREES F.
1
1
1
1
PHENOL
1
1 1 1
PHOSPHORIC ACID (3 MOLAR)
3
3 2 2
PHOSPHORIC ACID (CONCENTRATED) 3
3 2 2
PHOSPHOROUS TRICHLORIDE
3
3 1 1
PICRIC ACID, MOLTEN
3
3 2 2
PICRIC ACID, WATER SOLUTION
3
3 2 2
PINE OIL
2
2 1 2
PLATING SOLUTIONS (CHROME)
1
3 1 1
PLATING SOLUTIONS (OTHER)
4
1 1 1
PNEUMATIC SERVICE
1
1 1 1
POTASSIUM ACETATE
2
1 2 2
POTASSIUM CHLORIDE
3
3 1 2
POTASSIUM CYANIDE
3
2 2 2
POTASSIUM DICHROMATE
3
1 2 2
POTASSIUM HYDROXIDE (50%)
3
2 1 2
POTASSIUM NITRATE
2
1 1 1
POTASSIUM SALTS
4
4 4 4
POTASSIUM SULFATE
3
2 1 1
PRL-HIGH TEMP. HYDR. OIL
4
4 4 4
PRODUCER GAS
2
1 1 1
PROPANE
1
3 1 1
PROPYL ACETATE
3
1 1 1
PROPYL ALCOHOL
1
1 1 1
PROPYLENE
1
1 1 1
PYDRAUL 10E
3
1 1 1
PYDRAUL A-200, C SERIES
3
1 1 1
PYDRAUL, 3 SERIES
3
1 1 1
PYROGARD 42, 43, 53, 55
(PHOSPHATE ESTER)
4
4 4 4
IV
1 3 1
1 3 1
1 1 2
2 3 1
1 3 1
2 3 1
1 1 1
1 3 1
3 3 1
1 3 1
2 1 4
2 3 1
3 3 1
2 3 1
1 2 1
2 1 3
1 1 1
1 1 1
1 1 1
1 1 1
1 4 4
2 3 1
1 2 1
3 3 1
2 1 1
3 3 2
2 1 1
3 1 1
1 2 1
3 3 1
1 3 1
1 3 1
1
3
1
3 2 1
2 3 1
1 3 1
1
3
1
3 3 1
1 1 1
3 1 1
3 1 1
2 2 1
1 1 1
1 3 1
4 1 1
1 1 1
1 1 1
2 1 3
1 1 1
1 1 1
1 1 1
2 1 3
1 1 1
1 1 1
1 1 1
2 3 1
1 3 1
1 3 1
3 2 3
1 1 1
3 3 1
3 1 3
3 3 1
3 1 1
2
1
2
1
2
3
1
2
3
2
2
3
3
3
3
2
2
2
1
1
4
2
2
3
2
3
1
3
2
3
1
3
2
2
3
2
2
3
2
3
3
2
1
3
3
3
1
2
1
1
1
2
1
1
1
2
2
2
3
1
3
3
3
3
3 1 1

Minneapolis, MN
Appendix
PYROGARD D
SEA WATER (SALT WATER)
SHELL IRUS 905
SILICONE GREASES
SILVER NITRATE
SKYDROL 500, TYPE 2
SKYDROL 7000, TYPE 2
SOAP SOLUTIONS
SODIUM ACETATE
SODIUM BICARBONATE (BAKING SODA)
SODIUM BISULPHATE OR BISULPHITE
SODIUM BORATE
SODIUM CARBONATE (SODA ASH)
SODIUM CHLORIDE
SODIUM CYANIDE
SODIUM HYDROXIDE (CAUSTIC SODA, LYE)
SODIUM HYDROXIDE, 50%
SODIUM METAPHOSPHATE
SODIUM NITRATE
SODIUM PERBORATE
SODIUM PEROXIDE
SODIUM PHOSPHATES
SODIUM SALTS
SODIUM SULFATE
SODIUM SULFIDE AND SULFITE
SODIUM THIOSULFATE
SOYBEAN OIL
STANNOUS CHLORIDE (15%)
STEAM, BELOW 400 DEGEEES F.
STODDARD SOLVENT
SUCROSE SOLUTIONS
SULFUR
SULFUR LIQUORS
SULFUR (MOLTEN)
SULFUR DIOXIDE (DRY)
SULFUR TRIOXIDE (DRY)
SUNSAFE
TANNIC ACID (10%)
TAR, BITUMINOUS
TARTARIC ACID
TERPINEOL
TERTIARY BUTYL ALCOHOL
TETRACHLOROETHANE
TETRACHLOROETHYLENE
TETRAETHYL LEAD
TETRAETHYL LEAD (BLEND)
TITANIUM TETRACHLORIDE
TOLUENE
TRANSFORMER OIL
TRANSMISSION FLUID (TYPE A)
TRICHLOROETHANE
TRICHLOROETHYLENE
TRICRESYL PHOSPHATE
TURBINE OIL #15 (MIL-L-7808A)
TURPENTINE
VARNISH
WATER
WHISKEY
WINE
WOOD OIL
XYLENE
ZINC SULFATE

Nitrile
E.P. Fluorocarbon Neoprene
4
4 4 4
2
3
1
1
4
4
4
4
1
1 1 1
3
3 1 2
3
1
1
1
3
1
1
1
3
3 1 1
1
1 1 1
2
2
1
1
3
3
2
1
3
2 2 2
4
1
1
1
3
2 2 2
3
1 1 1
3
2
1
2
3
3
1
2
2
1 2 2
3
2 1 1
3
3 1 1
3
1 2 2
1
3 2 1
4
4 4 4
3
2 1 1
3
3
2
3
3
3 1 2
2
1 1 1
3
3
2
3
1
3
1
1
2
1 1 1
1
1 1 1
2
1 1 1
1
1 1 1
3
3 1 1
3
1
1
3
2
2
2
3
3
1 1 1
1
3
2
3
2
1 1 1
2
3 3 2
4
4 4 4
1
1
1
1
4
2 1 2
3
2 2 4
1
1 1 1
1
1
1
1
2
1 2 3
1
1 1 1
1
1 1 1
1
1
1
1
4
2 1 4
3
2 2 2
4
1 2 2
4
2
1
1
3
2 1 1
1
1 1 1
1
3 1 1
1
3 1 1
1
3 1 1
4
2 1 1
1
2 1 1
3
3 2 2
1
3
1
1
1
3
1
1
2
1
3
1
3
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
2
1
2
1
2
1
1
1
1
1
1
1
1
1
2
1
1
3
1
1
3
1*
1
3
1
1
3
1
2
2
3
3
3
1
3
2
1
3
1
1
2
3
1
2
2
3
2
2
3
3
3
3
2
3
2
3
2
3
3
3
1
3
1
3
3
3
3
3
3
1
2
3
1
3
2
3
1
1
1
1
1
1
1
3
3
3
1
1
3
1
1
1
1
3
2
1
3
1
1
1
1
1
4
2
2
1
4
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
2
2
2
1
1
3
3
2
2
1
1
1
1
1
1
2
2
2
2
2
2
2
2
1
1
1
3
1
3
2
2
1
2
3
3
3
2
2
3
2
3
2
3
3
2
3
3
3
2
2
3
3
3
3
3
3
2
1
1
2
3
1

Minneapolis, MN
Appendices

MEDIA
Appendix
PF Series (Plastic/Polypropylene Material)

Ratings Code:
Appendices
G Good to excellent. Little or no swelling, tensile or surface changes. Preferred choice.

L Marginal or conditional. Noticeable effects but not necessarily indicating lack of serviceability. Further testing suggested
for
specific application.Very long-term effects such as stiffening or potential for crazing should be evaluated.
P Poor or unsatisfactory. Not recommended without extensive and realistic testing.
Indicates that this was not tested.
# For Teflon. Indicates good chemical resistance but potential for excessive permeation.
MEDIA Rating
MEDIA Rating
Acetaldehyde P
Acetates L
Acetic Acid
G
L
Acetic Anhydride
Acetone G
Acetyl Bromide
Acetyl Chloride
L
Air G
Alcohols L
Aluminum Salts
G
Ammonia G
Amyl Acetate
L
Aniline G
Animal Oils
G
Arsenic Salts
L
Aromatic Hydrocarbons
Barium Salts
G
Benzaldehyde L
Benzene (Benzol)
L
Benzyl Alcohol
G
Bleaching Liquors
Boric Acid Solution

G
Bromine P
Butane L
Butanol
Butyl Acetate
P
Calcium Salts
G
G
Carbon Dioxide
Carbon Disulfide
L
Carbon Tetrachloride
P
Caustic Potash
G
G
Caustic Soda
Chloracetic Acid
L
Chlorine (Dry)
P
Chlorine (Wet)
P
Chlorobenzene P
Chloroform P
Chromic Acid
G
Copper Salts
G
Cresol L
Cyclohexanone L
Ethers P
L
Ethyl Acetate
Ethyl Alcohol
G
Ethylamine L
Ethyl Bromide
Ethyl Chloride
P
Fatty Acids
G
Ferric Salts
G
Formaldehyde G
Formic Acid
G
Freon L
Gasoline L
Glucose G
Glycerine G
Hydriodic Acid
Hydrochloric Acid (Conc.)
G
G
Hydrochloric Acid (Med. Conc.)
Hydrofluoric Acid
G
L
Hydrogen Peroxide (Conc.)
Hydrogen Peroxide (Dil.)
L
G
Hydrogen Sulfide
Iodine G
Kerosene P
Ketones G
Lacquer Solvent
L
Lactic Acid
G
Lead Acetate
G
Linseed Oil
G
Magnesium Salts
G
Naphtha L
Natural Gas
L
Nickel Salts
G
Nitric Acid (Conc.)
P
Nitric Acid (Dil.)
L
Nitrobenzene G
Nitrogen Oxides
Nitrous Acid
G
Oils (Animal and Mineral)
L
Oils (Vegetable)
L
Oxygen L
L
Perchloric Acid
Phenol G
Potassium Salts
G
Pyridine G
G
Silver Nitrate
Soap Solutions
G
Sodium Salts
G
Stearic Acid
L
Sulfur Chloride
P
Sulfuric Acid (Conc.)
L
Sulfuric Acid (Dil.)
G
Sulfurous Acid
L
Tannic Acid
G
Tanning Extracts
L
Titanium Salts
P
Toluene (Toluol)
Trichloracetic Acid
G
Trichlorethylene P
Turpentine P
Urea G
Uric Acid
Water G
Xylene (Xylol)
P
Zinc Chloride
G
VI

Minneapolis, MN
Appendix
Safety Guide
SAFETY GUIDE FOR SELECTING AND USING QUICK

ACTION COUPLINGS AND RELATED ACCESSORIES
DANGER: Failure or improper selection or improper use of quick action couplings or related accessories can
cause death, personal injury and property damage. Possible consequences of failure or improper selection or
improper use of quick action couplings or related accessories include but are not limited to:
Couplings or parts thrown off at high speed.
Dangerously whipping hose.
High velocity fluid discharge.
Contact with conveyed fluids that may be hot,
Explosion or burning of the conveyed fluid. cold, toxic, or otherwise injurious.
Contact with suddenly moving or falling objects
Sparking or explosion while paint or flammable
that are to be held in position or moved by the liquid spraying.
conveyed fluid.
Before selecting or using any Parker quick action couplings or related accessories, it is important that you read
and follow the following instructions.
1.2Fail-Safe: Quick action couplings or the hose they are

attached to can fail without warning for many reasons. Design
all systems and equipment in a fail-safe mode, so that failure
of the quick action coupling or hose will not endanger persons
or property.
1.3Distribution: Provide a copy of this safety guide to each
person that is responsible for selecting or using quick action
coupling products. Do not select or use quick action couplings
without thoroughly reading and understanding this safety guide
as well as the specific Parker publications for the products
considered or selected.
1.4 User Responsibility: Due to the wide variety of operating
conditions and uses for quick action couplings, Parker and its
distributors do not represent or warrant that any particular quick
action coupling is suitable for any specific end use system. This
safety guide does not analyze all technical parameters that
must be considered in selecting a product. The user, through
its own analysis and testing, is solely responsible for:
Making the final selection of the quick action couplings.
Assuring that the users requirements are met and that the
use presents no health or safety hazards.
Providing all appropriate health and safety warnings on the
equipment on which the quick action couplings are used.
1.5 Additional Questions: Call the appropriate Parker customer
service department if you have any questions or require any
additional information. For the telephone numbers of the
appropriate customer service department, see the Parker
publication for the product being considered or used.
2.0 QUICK ACTION COUPLING SELECTION INSTRUCTIONS
2.1Pressure: Quick action couplings selection must be made
so that the published rated pressure of the coupling is equal to
or greater than the maximum system pressure. Surge pressures
in the system higher than the rated pressure of the coupling will
shorten the quick action couplings life. Do not confuse burst
pressure or other pressure values with rated pressure and do
not use burst pressure or other pressure values for this purpose.
2.2 Fluid Compatibility: Quick action couplings selection must

assure compatibility of the body and seal materials with the
fluid media used. See the fluid compatibility chart in the Parker
publication for the product being considered or used.
2.3Temperature: Be certain that fluid and ambient
temperatures, both steady and transient, do not exceed the
limitations of the quick action couplings. Use caution and hand
protection when connecting or disconnecting quick action
couplings that are heated or cooled by the media they are
conducting or by their environment.
2.4Size: Transmission of power by means of pressurized
liquid varies with pressure and rate of flow. The size of the quick
action couplings and other components of the system must be
adequate to keep pressure losses to a minimum and avoid
damage due to heat generation or excessive fluid velocity.
2.5 Pressurized Connect or Disconnect: If connecting or
disconnecting under pressure is a requirement, use only quick
action couplings designed for that purpose. The rated operating
pressure of a quick action coupling may not be the pressure at
which it may be safely connected or disconnected.
2.6Environment: Care must be taken to ensure that quick
action couplings are either compatible with or protected from
the environment (that is, surrounding conditions) to which
they are exposed. Environmental conditions including but not
limited to ultraviolet radiation, ozone, moisture, water, salt
water, chemicals, and air pollutants can cause degradation and
premature failure.
2.7 Locking Means: Ball locking quick action couplings can
unintentionally disconnect if they are dragged over obstructions
on the end of a hose or if the sleeve is bumped or moved
enough to cause disconnect. Sleeves designed with flanges to
provide better gripping for oily or gloved hands are especially
susceptible to accidental disconnect and should not be used
where these conditions exist. Sleeve lock or union (threaded)
sleeve designs should be considered where there is a potential
for accidental uncoupling.
2.8 Mechanical Loads: External forces can significantly reduce
quick action couplings life or cause failure. Mechanical loads
which must be considered include excessive tensile or side
loads, and vibration. Unusual applications may require special
testing prior to quick action couplings selection.
2.9 Specifications and Standards: When selecting quick action
couplings, government, industry, and Parker specifications
must be reviewed and followed as applicable.
VII

Minneapolis, MN
Appendices
1.1Scope: This safety guide provides instructions for selecting

and using (including installing connecting, disconnecting, and
maintaining) quick action couplings and related accessories
(including caps, plugs, blow guns, and two way valves). This
safety guide is a supplement to and is to be used with, the
specific Parker publications for the specific quick action
couplings and related accessories that are being considered
for use.
Appendix
Safety Guide
2.10Vacuum: Not all quick action couplings are suitable or

recommended for vacuum service. Quick action couplings used
for vacuum applications must be selected to ensure that the
quick actions couplings will withstand the vacuum and pressure
of the system.
3.6 Hose Whips: Use a hose whip (a short length of hose

between the tool and the coupling half) instead of rigidly
mounting a coupling half on hand tools or other devices. This
reduces the potential for coupling damage if the tool is dropped
and provides some isolation from mechanical vibration which
could cause uncoupling.
2.11 Fire Resistant Fluids: Some fire resistant fluids require

seals other than the standard nitrile used in many quick action
couplings.
4.0 QUICK ACTION COUPLING MAINTENANCE INSTRUCTIONS

4.1 Even with proper selection and installation, quick action
coupling life may be significantly reduced without a continuing
maintenance program. Frequency should be determined by the
severity of the application and risk potential. A maintenance
program must be established and followed by the user and
must include the following as a minimum:
2.12 Radiant Heat: Quick action couplings can be heated to

destruction or loss of sealability without contact by such nearby
items as hot manifolds or molten metal. The same heat source
may then initiate a fire. This can occur despite the presence of
cool air around the quick action couplings.
4.2 Visual Inspection of Quick Action Couplings: Any of the

following conditions require immediate shut down and
replacement of the quick action coupling:
2.13 Welding and Brazing: Heating of plated parts, including

quick action couplings and port adapters, above 450F (232C)
such as during welding, brazing, or soldering may emit deadly
gases and may cause coupling seal damage.
Cracked, damaged, or corroded quick action coupling parts.
3.0 QUICK ACTION COUPLING INSTALLATION INSTRUCTIONS
Leaks at the fitting, valve or mating seal.
3.1 Pre-Installation Inspection: Before installing a quick

action coupling, visually inspect it and check for correct style,
body material, seal material, and catalog number. Before
final installation, coupling halves should be connected and
disconnected with a sample of the mating half with which
they will be used.
Broken coupling mounting hardware, especially breakaway

clamps.
3.2 Quick Action Coupling Halves From Other Manufacturers

If a quick action coupling assembly is made up of one Parker
half and one half from another manufacturer, the lowest
pressure rating of the two halves should not be exceeded.
Remove excess dirt buildup on the coupling locking means

or on the interface area of either coupling half.
3.3 Fitting Installation: Use a thread sealant, lubricant, or

a combination of both when assembling pipe thread joints in
quick action couplings. Be sure the sealant is compatible with
the system fluid or gas. To avoid system contamination, use a
liquid or paste type sealant rather than a tape style. Use the
flats provided to hold the quick action coupling when installing
fittings. Do not use pipe wrenches or a vice on other parts of
the coupling to hold it when installing or removing fittings as
damage or loosening of threaded joints in the coupling assembly
could result. Do not apply excessive torque to taper pipe threads
because cracking or splitting of the female component can
result.
4.4 Functional Test: Operate the system at maximum operating pressure and check for possible malfunctions and freedom
from leaks. Personnel must avoid potential hazardous areas
while testing and using the system.
3.4 Caps and Plugs: Use dust caps and plugs when quick
action couplings are not coupled to exclude dirt and
contamination and to protect critical surfaces from damage.
Leaking seals or port connections.
Clamps, guards, and shields.

System fluid level, fluid type and any air entrapment.
4.5 Replacement Intervals: Specific replacement intervals

must be considered based on previous service life, government
or industry recommendations, or when failures could result in
unacceptable downtime, damage or injury risk. See instruction
1.2 above.
Additional copies of the preceding safety information can be
ordered by requesting Safety Guide For Selecting and Using
Quick Action Couplings and Related Accessories, Parker
Publication No. 3800-B1.0
Contact The Quick Coupling Division, Minneapolis, MN.
Appendices
3.5 Coupling Location: Locate quick action couplings where

they can be reached for connect or disconnect without exposing
the operator to slipping, falling, getting sprayed, or coming in
contact with hot or moving parts.
4.3 Visual Inspection All Other: The following items must be

tightened, repaired or replaced as required:
VIII

Minneapolis, MN
Appendix
Offer of Sale
1. Terms and Conditions. Sellers willingness to offer Products, or accept an order for Products,
to or from Buyer is subject to these Terms and Conditions or any newer version of the terms
and conditions found on-line at www.parker.com/saleterms/. Seller objects to any contrary or
additional terms or conditions of Buyers order or any other document issued by Buyer.
12. Cancellations and Changes. Orders shall not be subject to cancellation or change by Buyer
for any reason, except with Sellers written consent and upon terms that will indemnify, defend and
hold Seller harmless against all direct, incidental and consequential loss or damage. Seller may
change product features, specifications, designs and availability with or without notice to Buyer.
2. Price Adjustments; Payments. Prices stated on Sellers quote or other documentation offered
by Seller are valid for 30 days, and do not include any sales, use, or other taxes unless specifically
stated. Unless otherwise specified by Seller, all prices are F.C.A. Sellers facility (INCOTERMS
2010). Payment is subject to credit approval and is due 30 days from the date of invoice or such
other term as required by Sellers Credit Department, after which Buyer shall pay interest on any
unpaid invoices at the rate of 1.5% per month or the maximum allowable rate under applicable law.
13. Limitation on Assignment. Buyer may not assign its rights or obligations under this agreement
without the prior written consent of Seller.
14. Force Majeure. Seller does not assume the risk and shall not be liable for delay or failure
to perform any of Sellers obligations by reason of circumstances beyond the reasonable control
of Seller (hereinafter Events of Force Majeure). Events of Force Majeure shall include without
limitation: accidents, strikes or labor disputes, acts of any government or government agency,
acts of nature, delays or failures in delivery from carriers or suppliers, shortages of materials, or
any other cause beyond Sellers reasonable control.
3. Delivery Dates; Title and Risk; Shipment. All delivery dates are approximate and Seller
shall not be responsible for any damages resulting from any delay. Regardless of the manner of
shipment, title to any products and risk of loss or damage shall pass to Buyer upon placement
of the products with the shipment carrier at Sellers facility. Unless otherwise stated, Seller may
exercise its judgment in choosing the carrier and means of delivery. No deferment of shipment
at Buyers request beyond the respective dates indicated will be made except on terms that will
indemnify, defend and hold Seller harmless against all loss and additional expense. Buyer shall be
responsible for any additional shipping charges incurred by Seller due to Buyers acts or omissions.
15. Waiver and Severability. Failure to enforce any provision of this agreement will not waive
that provision nor will any such failure prejudice Sellers right to enforce that provision in the
future. Invalidation of any provision of this agreement by legislation or other rule of law shall not
invalidate any other provision herein. The remaining provisions of this agreement will remain in
full force and effect.
4. Warranty. Seller warrants that the Products sold hereunder shall be free from defects in
material or workmanship for a period of twelve months from the date of delivery to Buyer or 2,000
hours of normal use, whichever occurs first. The prices charged for Sellers products are based
upon the exclusive limited warranty stated above, and upon the following disclaimer: DISCLAIMER
OF WARRANTY: THIS WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO
PRODUCTS PROVIDED HEREUNDER. SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS AND
IMPLIED, INCLUDING DESIGN, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
16. Termination. Seller may terminate this agreement for any reason and at any time by
giving Buyer thirty (30) days written notice of termination. Seller may immediately terminate
this agreement, in writing, if Buyer: (a) commits a breach of any provision of this agreement (b)
appointments a trustee, receiver or custodian for all or any part of Buyers property (c) files a
petition for relief in bankruptcy on its own behalf, or by a third party (d) makes an assignment for
the benefit of creditors, or (e) dissolves or liquidates all or a majority of its assets.
17. Governing Law. This agreement and the sale and delivery of all Products hereunder shall be
deemed to have taken place in and shall be governed and construed in accordance with the laws
of the State of Ohio, as applicable to contracts executed and wholly performed therein and without
regard to conflicts of laws principles. Buyer irrevocably agrees and consents to the exclusive
jurisdiction and venue of the courts of Cuyahoga County, Ohio with respect to any dispute,
controversy or claim arising out of or relating to this agreement.
5. Claims; Commencement of Actions. Buyer shall promptly inspect all Products upon delivery.
No claims for shortages will be allowed unless reported to the Seller within 10 days of delivery. No
other claims against Seller will be allowed unless asserted in writing within 30 days after delivery.
Buyer shall notify Seller of any alleged breach of warranty within 30 days after the date the defect
is or should have been discovered by Buyer. Any action based upon breach of this agreement or
upon any other claim arising out of this sale (other than an action by Seller for an amount due on
any invoice) must be commenced within 12 months from the date of the breach without regard to
the date breach is discovered.
18. Indemnity for Infringement of Intellectual Property Rights. Seller shall have no liability for
infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights
except as provided in this Section. Seller will defend and indemnify Buyer against allegations
of infringement of U.S. patents, U.S. trademarks, copyrights, trade dress and trade secrets
(Intellectual Property Rights). Seller will defend at its expense and will pay the cost of any
settlement or damages awarded in an action brought against Buyer based on an allegation
that a Product sold pursuant to this Agreement infringes the Intellectual Property Rights of a
third party. Sellers obligation to defend and indemnify Buyer is contingent on Buyer notifying
Seller within ten (10) days after Buyer becomes aware of such allegations of infringement,
and Seller having sole control over the defense of any allegations or actions including all
negotiations for settlement or compromise. If a Product is subject to a claim that it infringes
the Intellectual Property Rights of a third party, Seller may, at its sole expense and option,
procure for Buyer the right to continue using the Product, replace or modify the Product so
as to make it noninfringing, or offer to accept return of the Product and return the purchase
price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller
shall have no liability for claims of infringement based on information provided by Buyer, or
directed to Products delivered hereunder for which the designs are specified in whole or part
by Buyer, or infringements resulting from the modification, combination or use in a system of
any Product sold hereunder. The foregoing provisions of this Section shall constitute Sellers
sole and exclusive liability and Buyers sole and exclusive remedy for infringement of Intellectual
Property Rights.
6. LIMITATION OF LIABILITY. UPON NOTIFICATION, SELLER WILL, AT ITS OPTION, REPAIR OR

REPLACE A DEFECTIVE PRODUCT, OR REFUND THE PURCHASE PRICE. IN NO EVENT SHALL
SELLER BE LIABLE TO BUYER FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF, OR AS THE RESULT OF, THE SALE, DELIVERY, NON-DELIVERY,
SERVICING, USE OR LOSS OF USE OF THE PRODUCTS OR ANY PART THEREOF, OR FOR ANY
CHARGES OR EXPENSES OF ANY NATURE INCURRED WITHOUT SELLERS WRITTEN CONSENT,
EVEN IF SELLER HAS BEEN NEGLIGENT, WHETHER IN CONTRACT, TORT OR OTHER LEGAL
THEORY. IN NO EVENT SHALL SELLERS LIABILITY UNDER ANY CLAIM MADE BY BUYER
EXCEED THE PURCHASE PRICE OF THE PRODUCTS.
7. User Responsibility. The user, through its own analysis and testing, is solely responsible
for making the final selection of the system and Product and assuring that all performance,
endurance, maintenance, safety and warning requirements of the application are met. The user
must analyze all aspects of the application and follow applicable industry standards and Product
information. If Seller provides Product or system options, the user is responsible for determining
that such data and specifications are suitable and sufficient for all applications and reasonably
foreseeable uses of the Products or systems.
8. Loss to Buyers Property. Any designs, tools, patterns, materials, drawings, confidential
information or equipment furnished by Buyer or any other items which become Buyers property,
will be considered obsolete and may be destroyed by Seller after two consecutive years have
elapsed without Buyer ordering the items manufactured using such property. Seller shall not be
responsible for any loss or damage to such property while it is in Sellers possession or control.
19. Entire Agreement. This agreement contains the entire agreement between the Buyer and
Seller and constitutes the final, complete and exclusive expression of the terms of sale. All prior
or contemporaneous written or oral agreements or negotiations with respect to the subject
matter are herein merged.
9. Special Tooling. A tooling charge may be imposed for any special tooling, including without
limitation, dies, fixtures, molds and patterns, acquired to manufacture Products. Such special
tooling shall be and remain Sellers property notwithstanding payment of any charges by Buyer.
In no event will Buyer acquire any interest in apparatus belonging to Seller which is utilized in
the manufacture of the Products, even if such apparatus has been specially converted or adapted
for such manufacture and notwithstanding any charges paid by Buyer. Unless otherwise agreed,
Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other
property in its sole discretion at any time.
20. Compliance with Law, U. K. Bribery Act and U.S. Foreign Corrupt Practices Act. Buyer agrees
to comply with all applicable laws and regulations, including both those of the United Kingdom
and the United States of America, and of the country or countries of the Territory in which Buyer
may operate, including without limitation the U. K. Bribery Act, the U.S. Foreign Corrupt Practices
Act (FCPA) and the U.S. Anti-Kickback Act (the Anti-Kickback Act), and agrees to indemnify
and hold harmless Seller from the consequences of any violation of such provisions by Buyer, its
employees or agents. Buyer acknowledges that they are familiar with the provisions of the U.
K. Bribery Act, the FCPA and the Anti-Kickback Act, and certifies that Buyer will adhere to the
requirements thereof. In particular, Buyer represents and agrees that Buyer shall not make any
payment or give anything of value, directly or indirectly to any governmental official, any foreign
political party or official thereof, any candidate for foreign political office, or any commercial entity
or person, for the purpose of influencing such person to purchase products or otherwise benefit
the business of Seller.
10. Buyers Obligation; Rights of Seller. To secure payment of all sums due or otherwise, Seller
shall retain a security interest in the goods delivered and this agreement shall be deemed a
Security Agreement under the Uniform Commercial Code. Buyer authorizes Seller as its attorney
to execute and file on Buyers behalf all documents Seller deems necessary to perfect its security
interest.
Appendices
11. Improper use and Indemnity. Buyer shall indemnify, defend, and hold Seller harmless from
any claim, liability, damages, lawsuits, and costs (including attorney fees), whether for personal
injury, property damage, patent, trademark or copyright infringement or any other claim, brought
by or incurred by Buyer, Buyers employees, or any other person, arising out of: (a) improper
selection, improper application or other misuse of Products purchased by Buyer from Seller; (b)
any act or omission, negligent or otherwise, of Buyer; (c) Sellers use of patterns, plans, drawings,
or specifications furnished by Buyer to manufacture Product; or (d) Buyers failure to comply with
these terms and conditions. Seller shall not indemnify Buyer under any circumstance except as
otherwise provided.
IX

Minneapolis, MN
Appendix
Glossary of Terms
Air Inclusion: The ambient atmosphere forced into the system

during the connection of the quick disconnect halves.
Pressure Operating: The pressure at which a system

is operated.
Break-Away: Automatic disconnection of a coupling when an

axial separation force is applied.
Pressure Plug: Plug which incorporates a seal capable of

withstanding the rated pressures on the female half.
Brinelling: Dimples or grooves worn into the shoulder of a

male half by the locking balls in the female half.
Proof Pressure: The non-destructive test pressure in excess

of the maximum rated operating pressure.
Burst Pressure: The pressure at which a device loses the

capability to retain pressure.
Push To Connect (Auto Lock): Locking arrangement which

permits one handed connection by pushing the nipple into
the coupler.
Case Hardening: Hardening the surface of low carbon steel.
Rated Pressure: The maximum pressure at which a product

is designed to operate.
Cold Flow: Continued deformation under load.

Connect Under Pressure: Ability to connect coupling halves
with internal line pressure applied to either both sides or
one side.
Single-Acting Sleeve: Permits pull-to-disconnect convenience

on implement line when female body is clamp mounted.
Making connection requires manually pulling female body
forward, inserting male tip, then allowing body and tip to return
to original position in the clamp.
Coupling, Female Half: Other nomenclature coupler,

socket, body.
Sleeve Lock: Arrangement which provides an additional

lock which must be actuated before the locking sleeve can
be retracted.
Coupling, Male Half: Other nomenclature nipple, plug,

adapter.
Coupling, Quick Disconnect: A component which can
quickly join or separate a fluid line without the use of tools
or special devices.
Spillage: The fluid removed from the system due to

disconnection of a coupling assembly. This is the fluid
trapped between the mating seal and the valve seal of the
coupling halves.
Differential Pressure (P): The difference in pressure

between any two points of a system or a component.
Surge Pressure: The pressure existing from surge conditions.
Double-Acting Sleeve: Permits push-to-connect and pull-todisconnect convenience on implement line when female half
is clamp mounted and connected with a hose.
Surge Flows: A rapid increase in fluid flow.

Thermal Build-Up: Hydraulic pressure caused by expansion of
the fluid due to heat from an external source such as sunlight.
Dust Cap: Dust or dirt repelling enclosure for both halves.
Trapped Pressure: Pressurized hydraulic fluid trapped behind

closed coupling valve.
Dust Plug: Dust or dirt repelling enclosure both halves.

Flow Checking: Occurs when a nipple valve closes during
flow conditions, such as when quickly lowering a heavy
implement.(Also called Check Off, Back Checking or Lock-up.)
Twist Lock: A locking arrangement which requires a rotational

actuation to unlock the mating halves.
Flush Position (Valve): When the coupler valve is fully open,

allowing maximum oil flow.
Types of Quick Disconnect Coupling Valve:
Force to Connect: Axial and/or rotational force required to

make a complete connection.
Double Shut-off Valve (DSO): A valve in the female half and a

valve in the male half.
Force to Disconnect: The reverse of the above.
Single Shut-off Valve (SSO): Generally, a valve in the female

half with no valve in the male half.
Straight-Thru (ST): This provides straight through flow.
Appendices
Induction Hardening: Localized hardening of medium

carbon steel.
NOTE: Refer to Parkers Publication No. 3800-B1.0: Safety

Guide for Selecting and Using Quick Action Couplings and
Related Accessories.
Peak Pressure: Maximum momentary pressure encountered

in the operation of a component.
Pressure Cap: Cap which incorporates a seal capable of
withstanding the rated pressures on the male half.
Pressure Impulse Test: Subjecting a component to a specified
pressure at a specified rate of increase or decrease for a
specified time limit.

Minneapolis, MN
Quick Coupling Division Locations
About Parker Hannifin Corporation

Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. A Fortune 500
corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that
control motion in some 1,000 industrial and aerospace markets. Parker is the only manufacturer to 7,500 distributors serving
nearly 400,000 customers worldwide.
Parkers Charter
Minneapolis, MN
Grantsburg, WI
To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. More
specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve
profitable growth through premier customer service.
Product Information
North American customers seeking product information, the location of a nearby distributor, or repair services will receive
prompt attention by calling the Parker Product Information Center at our toll-free number: 1-800-C-PARKER (1-800-272-7537).
In Europe, call: 00800-C-PARKER-H (00800-2727-5374).
Chetek, WI
Union City, PA
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS
CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors
provide product or system options for further investigation by users having technical expertise.
The user, through its own analysis and testing, is solely responsible for making the final selection of the system and
components and assuring that all performance, endurance, maintenance, safety and warning requirements of the
application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow
the information concerning the product in the current product catalog and in any other materials provided from Parker or
its subsidiaries or authorized distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon
data or specifications provided by the user, the user is responsible for determining that such data and specifications are
suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.
Offer of Sale
The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its
authorized distributors. This offer and its acceptance are governed by the provisions stated in the Offer of Sale.
2014, Revised Feb 2014, Parker Hannifin Corporation, All Rights Reserved.
The Aerospace Group is a

leader in the development,
design, manufacture and
servicing of control systems
and components for aerospace
and related high-technology
markets, while achieving
growth through premier
customer service.
The Climate & Industrial

Controls Group designs,
system-control and fluidhandling components and
systems to refrigeration,
air-conditioning and industrial
customers worldwide.
The Fluid Connectors Group

designs, manufactures and
markets rigid and flexible
connectors, and associated
products used in pneumatic
and fluid systems.
The Seal Group designs,

manufactures and distributes
industrial and commercial
sealing devices and related
products by providing
superior quality and total
customer satisfaction.
The Hydraulics Group designs,

produces and markets a
full spectrum of hydraulic
to builders and users of
industrial and mobile
machinery and equipment.
The Filtration Group designs,

quality filtration and
clarification products,
providing customers with
the best value, quality,
technical support, and
global availability.
The Automation Group is

a leading supplier of pneumatic
and electromechanical
to automation customers
worldwide.
The Instrumentation Group

is a global leader in the design,
manufacture and distribution
of high-quality critical flow
components for worldwide
process instrumentation,
ultra-high-purity, medical
and analytical applications.
Parker Fluid Connectors Group

North American Divisions & Distribution Service Centers
Hose, Tubing and Bundles:

Available in a wide variety of
sizes and materials including
rubber, wire-reinforced,
thermoplastic, hybrid and
custom compounds.
Worldwide Availability:
Parker operates Fluid
Connectors manufacturing
locations and sales offices
throughout North America,
South America, Europe and
Asia-Pacific.
For information, call toll free...
1-800-C-PARKER
(1-800-272-7537)
Distribution Service Centers
Energy Products Division

Stafford, TX
phone 281 566 4500
fax 281 530 5353
Buena Park, CA
phone 714 522 8840
fax 714 994 1183
Fluid System Connectors

Division
Otsego, MI
phone 269 694 9411
fax 269 694 4614
Hose Products Division
Wickliffe, OH
phone 440 943 5700
fax 440 943 3129
Industrial Hose Division
Wickliffe, OH
phone 440 833 2173
fax 440 833 2122
Parflex Division
Ravenna, OH
phone 330 296 2871
fax 330 296 8433
Minneapolis, MN
phone 763 544 7781
fax 763 544 3418
Conyers, GA
phone 770 929 0330
fax 770 929 0230
Louisville, KY
phone 502 937 1322
fax 502 937 4180
Portland, OR
phone 503 283 1020
fax 503 283 2201
Toledo, OH
phone 419 878 7000
fax 419 878 7001
fax 419 878 7420
(FCG Kit Operations)
Canada
Grimsby, ONT
phone 905 945 2274
fax 905 945 3945
(Contact Grimsby for other
Service Center locations)
Fittings:
Available in inch and metric
sizes covering SAE, BSP,
DIN, GAZ, JIS and ISO thread
configurations, manufactured
from steel, stainless steel,
brass, aluminum, nylon and
thermoplastic.
North American Divisions
Catalog 3800
Your complete source for

quality tube fittings, hose & hose
fittings, brass & composite
fittings, quick disconnect
couplings, valves and assembly
tools, locally available from a
worldwide network of authorized
distributors.
Tube Fittings Division

Columbus, OH
phone 614 279 7070
fax 614 279 7685
Catalog 3800 /USA 19M 02/14 QCD AP

8145 Lewis Road
Minneapolis, MN 55427
phone 763 544 7781
fax 763 544 3418
February 2014
2014 Parker Hannifin Corporation

Quick Couplings, Swivels, Valves,
Diagnostic Equipment
Catalog 3800 USA | February 2014

3800 Appendices

Uploaded by

Copyright:

Available Formats

3800 Appendices

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

3800 Appendices

Uploaded by

Copyright:

Available Formats

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.

Parker Fluid Connectors Group

Hose, Tubing and Bundles:

Distribution Service Centers

Energy Products Division

Fluid System Connectors

Quick Coupling Products

North American Divisions

Your complete source for

Tube Fittings Division

Catalog 3800 /USA 19M 02/14 QCD AP

Parker Hannifin Corporation

2014 Parker Hannifin Corporation

Quick Coupling Products

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.com

Quick Coupling Division Locations

About Parker Hannifin Corporation

The Aerospace Group is a

The Climate & Industrial

The Fluid Connectors Group

The Seal Group designs,

The Hydraulics Group designs,

The Filtration Group designs,

The Automation Group is

The Instrumentation Group

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.com

Parker Hannifin Corporation

Fluid Compatibility Chart........................................................I

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.com

Parker Hannifin Corporation

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.com

Fluid Compatibility Chart

The following seal compound and body material

CODES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient Data Available

BODY MATERIAL SEAL MATERIAL

Parker Hannifin Corporation

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.com

Fluid Compatibility Chart

CODES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient Data Available

Parker Hannifin Corporation

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.com

Fluid Compatibility Chart

CODES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient Data Available

BODY MATERIAL SEAL MATERIAL

Parker Hannifin Corporation

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.com

Fluid Compatibility Chart

CODES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient Data Available

BODY MATERIAL SEAL MATERIAL

Parker Hannifin Corporation

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.com

Fluid Compatibility Chart

CODES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient Data Available

BODY MATERIAL SEAL MATERIAL

Parker Hannifin Corporation

Quick Coupling Division - Order Today, SHIP TODAY at www.PartsGopher.com

Fluid Compatibility Chart

PF Series (Plastic/Polypropylene Material)

G Good to excellent. Little or no swelling, tensile or surface changes. Preferred choice.

Boric Acid Solution