Analog Devices Welcomes Hittite Microwave Corporation: No Content On The Attached Document Has Changed

Analog Devices Welcomes
Hittite Microwave Corporation

NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC547LP3 / 547LP3E
v02.0612
Switches - SPDT - SMT
GaAs MMIC SPDT NON-REFLECTIVE

SWITCH, DC - 20 GHz
Typical Applications
Features
The HMC547LP3 & HMC547LP3E is ideal for:
High Isolation: >50 dB up to 5 GHz

>45 dB up to 15 GHz
Basestation Infrastructure
Low Insertion Loss: 1.6 dB @ 10 GHz

2 dB @ 20 GHz
Fiber Optics & Broadband Telecom

Microwave Radio & VSAT
Fast Switching
Military Radios, Radar, & ECM
Non-Reflective Design
Test Instrumentation
QFN SMT Package, 9 mm2
Functional Diagram
General Description
The HMC547LP3 & HMC547LP3E are general purpose broadband high isolation non-reflective GaAs
MESFET SPDT switches in low cost leadless QFN
surface mount plastic packages. Covering DC to
20 GHz, the switch offers high isolation and low
insertion loss. The switch features >50 dB isolation
up to 5 GHz and >45 dB isolation up to 15 GHz.
The switch operates using complementary negative
con-trol voltage logic lines of -5/0V and requires no
bias supply. The HMC547LP3 & HMC547LP3E are
packaged in leadless QFN 3x3 mm surface mount
packages.
Electrical Specifications, TA = +25 C, With 0/-5V Control, 50 Ohm System

Parameter
Insertion Loss
Isolation
DC - 6.0 GHz
DC - 15.0 GHz
DC - 20.0 GHz
Return Loss
Return Loss RF1, RF2
Min.
45
40
33
Typ.
Max.
Units
1.5
1.6
1.8
2.0
1.9
2.0
2.2
2.5
dB
dB
dB
dB
50
45
38
dB
dB
dB
On State
DC - 20.0 GHz
17
dB
Off State
DC - 6.0 GHz
DC - 15.0 GHz
DC - 20.0 GHz
25
17
13
dB
dB
dB
Input Power for 1 dB Compression
0.5 - 20.0 GHz
23
dBm
Input Third Order Intercept

(Two-Tone Input Power= +7 dBm Each Tone)
0.5 - 10.0 GHz

0.5 - 20.0 GHz
48
45
dBm
dBm
DC - 20 GHz
3
6
ns
ns
Switching Characteristics
tRISE, tFALL (10/90% RF)
tON, tOFF (50% CTL to 10/90% RF)
Frequency
DC - 6.0 GHz
DC - 10.0 GHz
DC - 15.0 GHz
DC - 20.0 GHz
20
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC547LP3 / 547LP3E
v02.0612

SWITCH, DC - 20 GHz
Return Loss
Insertion Loss
-5
-1
-2
-3
+25 C
+85 C
-40 C
-4
RFC
RF1,RF2 ON
RF1,RF2 OFF
-10
-15
-20
-25
-30
-5
-35
10
15
20
25
10
FREQUENCY (GHz)
Isolation Between Ports RFC and RF1/RF2
-10
-10
ISOLATION (dB)
ISOLATION (dB)
-40
-50
-30
-40
-50
-60
-60
-70
-70
-80
-80
0
10
15
20
25
10
FREQUENCY (GHz)
15
20
25
FREQUENCY (GHz)
Input P1dB and P0.1dB

Compression Point
Input Third Order Intercept Point

55
30
50
25
INPUT IP3 (dBm)
INPUT P1dB AND P0.1dB (dBm)
25
RF2 PATH ON
RF1 PATH ON
-20
RF1
RF2
-30
20
Isolation Between Ports RF1 and RF2
-20
15
FREQUENCY (GHz)
RETURN LOSS (dB)
INSERTION LOSS (dB)
20
P1dB
P0.1dB
15
45
40
+25 C
+85 C
-40 C
35
30
25
10
0
10
12
FREQUENCY (GHz)
14
16
18
20
10
12
14
16
18
20
FREQUENCY (GHz)
Phone: 978-250-3343
Fax: 978-250-3373
HMC547LP3 / 547LP3E
v02.0612

SWITCH, DC - 20 GHz
Absolute Maximum Ratings
Control Voltages
RF Input Power (Vctl = -5V)
+30 dBm
State
Bias Condition
Control Voltage Range (A & B)
+0.5V to -7.5 V
Low
0 to -0.5V @ 10 uA Max.
Hot Switch Power Level

(Vctl = -5V)
+23 dBm
High
-5V @ 3 uA Typ. to -7V @ 10 uA Typ. ( 0.5 V)
Channel Temperature
150 C
Continuous Pdiss (T=85C)

(derate 4 mW/C about 85C)
0.26 W
Thermal Resistance
(Insertion Loss Path)
420 C/W
Thermal Resistance
(Terminated Path)
250 C/W
Storage Temperature
-65 to +150 C
Operating Temperature
-40 to +85 C
ESD Sensitivity (HBM)
Class 1A
Truth Table
Control Input
Signal Path State
RFC to RF1
RFC to RF2
High
Low
On
Off
Low
High
Off
On
ELECTROSTATIC SENSITIVE DEVICE

OBSERVE HANDLING PRECAUTIONS
Phone: 978-250-3343
Fax: 978-250-3373
HMC547LP3 / 547LP3E
v02.0612

SWITCH, DC - 20 GHz
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
Outline Drawing
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.

6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOT FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC547LP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC547LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]

547
XXXX
547
XXXX
[1] Max peak reflow temperature of 235 C

[2] Max peak reflow temperature of 260 C
[3] 4-Digit lot number XXXX
Phone: 978-250-3343
Fax: 978-250-3373
HMC547LP3 / 547LP3E
v02.0612

SWITCH, DC - 20 GHz
Pin Descriptions
Pin Number
Function
Description
1, 5, 9, 12, 16
N/C
This pin should be connected to PCB RF ground to

maximize isolation
2, 4, 6, 8, 13, 15
GND
Package bottom has exposed metal paddle that must also

be connected to PCB RF ground.
3, 7, 14
RFC, RF1, RF2
This pin is DC coupled and matched to 50 Ohm. Blocking

capacitors are required if RF line potential is not equal to 0V.
10
See truth table and control voltage table.
11
See truth table and control voltage table.
Interface Schematic
Suggested Driver Circuit
Phone: 978-250-3343
Fax: 978-250-3373
HMC547LP3 / 547LP3E
v02.0612

SWITCH, DC - 20 GHz
Evaluation PCB
List of Materials for Evaluation PCB 105711 [1]

Item
Description
J1 - J3
PCB Mount SRI SMA Connector
J4 - J6
DC Pin
R1 - R2
100 Ohm Resistor, 0603 Pkg.
U1
HMC547LP3 / HMC547LP3E
SPDT Switch
PCB [2]
107521 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
The circuit board used in the application should be

generated with proper RF circuit design techniques.
Signal lines at the RF port should have 50 Ohm
impedance and the package ground leads and
package bottom should be connected directly to
the ground plane similar to that shown above. The
evaluation circuit board shown above is available
from Hittite Microwave Corporation upon request.
[2] Circuit Board Material: Rogers 4350
Phone: 978-250-3343
Fax: 978-250-3373

Analog Devices Welcomes Hittite Microwave Corporation: No Content On The Attached Document Has Changed

Uploaded by

Copyright:

Available Formats

Analog Devices Welcomes Hittite Microwave Corporation: No Content On The Attached Document Has Changed

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Analog Devices Welcomes Hittite Microwave Corporation: No Content On The Attached Document Has Changed

Uploaded by

Copyright:

Available Formats

Analog Devices Welcomes

Hittite Microwave Corporation

THIS PAGE INTENTIONALLY LEFT BLANK

Switches - SPDT - SMT

GaAs MMIC SPDT NON-REFLECTIVE

The HMC547LP3 & HMC547LP3E is ideal for:

High Isolation: >50 dB up to 5 GHz

Low Insertion Loss: 1.6 dB @ 10 GHz

Fiber Optics & Broadband Telecom

Military Radios, Radar, & ECM

QFN SMT Package, 9 mm2

Electrical Specifications, TA = +25 C, With 0/-5V Control, 50 Ohm System

Input Power for 1 dB Compression

0.5 - 20.0 GHz

Input Third Order Intercept

0.5 - 10.0 GHz

GaAs MMIC SPDT NON-REFLECTIVE

Isolation Between Ports RFC and RF1/RF2

Input P1dB and P0.1dB

Input Third Order Intercept Point

INPUT P1dB AND P0.1dB (dBm)

Isolation Between Ports RF1 and RF2

Switches - SPDT - SMT

RETURN LOSS (dB)

INSERTION LOSS (dB)

GaAs MMIC SPDT NON-REFLECTIVE

Switches - SPDT - SMT

Absolute Maximum Ratings

RF Input Power (Vctl = -5V)

Control Voltage Range (A & B)

Hot Switch Power Level

-5V @ 3 uA Typ. to -7V @ 10 uA Typ. ( 0.5 V)

Continuous Pdiss (T=85C)

ESD Sensitivity (HBM)

Signal Path State

ELECTROSTATIC SENSITIVE DEVICE

GaAs MMIC SPDT NON-REFLECTIVE

Switches - SPDT - SMT

5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.

Package Body Material

Low Stress Injection Molded Plastic

RoHS-compliant Low Stress Injection Molded Plastic

Package Marking [3]

[1] Max peak reflow temperature of 235 C

GaAs MMIC SPDT NON-REFLECTIVE

Switches - SPDT - SMT

This pin should be connected to PCB RF ground to

Package bottom has exposed metal paddle that must also

RFC, RF1, RF2

This pin is DC coupled and matched to 50 Ohm. Blocking

See truth table and control voltage table.

See truth table and control voltage table.

Suggested Driver Circuit

GaAs MMIC SPDT NON-REFLECTIVE

Switches - SPDT - SMT

List of Materials for Evaluation PCB 105711 [1]

PCB Mount SRI SMA Connector

100 Ohm Resistor, 0603 Pkg.