Drive

General-Purpose AC Servo
J2-Super Series
CC-Link Compatible
MODEL
J2-Super Series
MR-J2S- CP-S084
SERVO AMPLIFIER
INSTRUCTION MANUAL
MR-J2S- CP-S084
Servo Amplifier Instruction Manual
MODEL
MODEL
CODE
HEAD OFFICE : TOKYO BLDG MARUNOUCHI TOKYO 100-8310

F
F
This Instruction Manual uses recycled paper.

SH (NA) 030036-F (0709) MEE Printed in Japan Specifications subject to change without notice.
Safety Instructions
(Always read these instructions before using the equipment.)
Do not attempt to install, operate, maintain or inspect the servo amplifier and servo motor until you have read
through this Instruction Manual, Installation guide, Servo motor Instruction Manual and appended documents
carefully and can use the equipment correctly. Do not use the servo amplifier and servo motor until you have a
full knowledge of the equipment, safety information and instructions.
In this Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".
Indicates that incorrect handling may cause hazardous conditions,

WARNING resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous conditions,

CAUTION resulting in medium or slight injury to personnel or may cause physical
damage.
Note that the CAUTION level may lead to a serious consequence according to conditions. Please follow the
instructions of both levels because they are important to personnel safety.
What must not be done and what must be done are indicated by the following diagrammatic symbols:
: Indicates what must not be done. For example, "No Fire" is indicated by .
: Indicates what must be done. For example, grounding is indicated by .
In this Instruction Manual, instructions at a lower level than the above, instructions for other functions, and so
on are classified into "POINT".
After reading this installation guide, always keep it accessible to the operator.
A- 1
1. To prevent electric shock, note the following
WARNING
Before wiring or inspection, turn off the power and wait for 15 minutes or more until the charge lamp turns
off. Then, confirm that the voltage between P and N is safe with a voltage tester and others. Otherwise,
an electric shock may occur. In addition, always confirm from the front of the servo amplifier, whether the
charge lamp is off or not.
Connect the servo amplifier and servo motor to ground.
Any person who is involved in wiring and inspection should be fully competent to do the work.
Do not attempt to wire the servo amplifier and servo motor until they have been installed. Otherwise, you
may get an electric shock.
Operate the switches with dry hand to prevent an electric shock.
The cables should not be damaged, stressed, loaded, or pinched. Otherwise, you may get an electric
shock.
During power-on or operation, do not open the front cover of the servo amplifier. You may get an electric
shock.
Do not operate the servo amplifier with the front cover removed. High-voltage terminals and charging area
are exposed and you may get an electric shock.
Except for wiring or periodic inspection, do not remove the front cover even of the servo amplifier if the
power is off. The servo amplifier is charged and you may get an electric shock.
2. To prevent fire, note the following
CAUTION
Install the servo amplifier, servo motor and regenerative resistor on incombustible material. Installing them
directly or close to combustibles will lead to a fire.
Always connect a magnetic contactor (MC) between the main circuit power supply and L1, L2, and L3 of
the servo amplifier, and configure the wiring to be able to shut down the power supply on the side of the
servo amplifier’s power supply. If a magnetic contactor (MC) is not connected, continuous flow of a large
current may cause a fire when the servo amplifier malfunctions.
When a regenerative resistor is used, use an alarm signal to switch main power off. Otherwise, a
regenerative transistor fault or the like may overheat the regenerative resistor, causing a fire.
3. To prevent injury, note the follow
CAUTION
Only the voltage specified in the Instruction Manual should be applied to each terminal. Otherwise, a burst,
damage, etc. may occur.
Connect the terminals correctly to prevent a burst, damage, etc.
Ensure that polarity ( , ) is correct. Otherwise, a burst, damage, etc. may occur.
Take safety measures, e.g. provide covers, to prevent accidental contact of hands and parts (cables, etc.)
with the servo amplifier heat sink, regenerative resistor, servo motor, etc.since they may be hot while
power is on or for some time after power-off. Their temperatures may be high and you may get burnt or a
parts may damaged.
During operation, never touch the rotating parts of the servo motor. Doing so can cause injury.
A- 2
4. Additional instructions
The following instructions should also be fully noted. Incorrect handling may cause a fault, injury, electric
shock, etc.
(1) Transportation and installation
CAUTION
Transport the products correctly according to their weights.
Stacking in excess of the specified number of products is not allowed.
Do not carry the servo motor by the cables, shaft or encoder.
Do not hold the front cover to transport the servo amplifier. The servo amplifier may drop.
Install the servo amplifier in a load-bearing place in accordance with the Instruction Manual.
Do not climb or stand on servo equipment. Do not put heavy objects on equipment.
The servo amplifier and servo motor must be installed in the specified direction.
Leave specified clearances between the servo amplifier and control enclosure walls or other equipment.
Do not install or operate the servo amplifier and servo motor which has been damaged or has any parts
missing.
When you keep or use it, please fulfill the following environmental conditions.
Conditions
Environment
Servo amplifier Servo motor
In [ ] 0 to 55 (non-freezing) 0 to 40 (non-freezing)
Ambient operation [ ] 32 to 131 (non-freezing) 32 to 104 (non-freezing)
temperature [ ] 20 to 65 (non-freezing) 15 to 70 (non-freezing)
In storage
[ ] 4 to 149 (non-freezing) 5 to 158 (non-freezing)
Ambient In operation 90%RH or less (non-condensing) 80%RH or less (non-condensing)
humidity In storage 90%RH or less (non-condensing)
Ambience Indoors (no direct sunlight) Free from corrosive gas, flammable gas, oil mist, dust and dirt
Altitude Max. 1000m (3280 ft) above sea level
HC-KFS Series
HC-MFS Series X Y : 49
HC-UFS13 to 73
HC-SFS81
HC-SFS52 to 152
HC-SFS53 to 153 X Y : 24.5
HC-RFS Series
[m/s2] 5.9 or less
HC-UFS 72 152
HC-SFS121 201
HC-SFS202 352 X : 24.5
HC-SFS203 353 Y : 49
HC-UFS202
X : 24.5
HC-SFS301
(Note) Y : 29.4
Vibration HC-KFS Series
HC-MFS Series X Y : 161
HC-UFS 13 to 73
HC-SFS81
HC-SFS52 to 152
HC-SFS53 to 153 X Y : 80
HC-RFS Series
[ft/s2] 19.4 or less
HC-UFS 72 152
HC-SFS121 201
HC-SFS202 352 X : 80
HC-SFS203 353 Y : 161
HC-UFS202
X : 80
HC-SFS301
Y : 96
Note. Except the servo motor with reduction gear.
A- 3
CAUTION
Provide adequate protection to prevent screws and other conductive matter, oil and other combustible
matter from entering the servo amplifier and servo motor.
Do not drop or strike servo amplifier or servo motor. Isolate from all impact loads.
Securely attach the servo motor to the machine. If attach insecurely, the servo motor may come off during
operation.
The servo motor with reduction gear must be installed in the specified direction to prevent oil leakage.
Take safety measures, e.g. provide covers, to prevent accidental access to the rotating parts of the servo
motor during operation.
Never hit the servo motor or shaft, especially when coupling the servo motor to the machine. The encoder
may become faulty.
Do not subject the servo motor shaft to more than the permissible load. Otherwise, the shaft may break.
When the equipment has been stored for an extended period of time, consult Mitsubishi.
(2) Wiring
CAUTION
Wire the equipment correctly and securely. Otherwise, the servo motor may misoperate.
Do not install a power capacitor, surge absorber or radio noise filter (FR-BIF option) between the servo
motor and servo amplifier.
Connect the output terminals (U, V, W) correctly. Otherwise, the servo motor will operate improperly.
Connect the servo motor power terminal (U, V, W) to the servo motor power input terminal (U, V, W)
directly. Do not let a magnetic contactor, etc. intervene.
Servo amplifier Servo motor Servo amplifier Servo motor

U U
U U
V V
V M V M
W W
W W
Do not connect AC power directly to the servo motor. Otherwise, a fault may occur.
The surge absorbing diode installed on the DC output signal relay of the servo amplifier must be wired in
the specified direction. Otherwise, the forced stop (EMG) and other protective circuits may not operate.
Servo amplifuer Servo amplifuer
COM COM
(24VDC) (24VDC)
Control Control
output output
RA RA
signal signal
When the cable is not tightened enough to the terminal block (connector), the cable or terminal block
(connector) may generate heat because of the poor contact. Be sure to tighten the cable with specified
torque.
A- 4
(3) Test run adjustment
CAUTION
Before operation, check the parameter settings. Improper settings may cause some machines to perform
unexpected operation.
The parameter settings must not be changed excessively. Operation will be insatiable.
(4) Usage
CAUTION
Provide an external emergency stop circuit to ensure that operation can be stopped and power switched
off immediately.
Any person who is involved in disassembly and repair should be fully competent to do the work.
Before resetting an alarm, make sure that the run signal of the servo amplifier is off to prevent an
accident. A sudden restart is made if an alarm is reset with the run signal on.
Do not modify the equipment.
Use a noise filter, etc. to minimize the influence of electromagnetic interference, which may be caused by
electronic equipment used near the servo amplifier.
Burning or breaking a servo amplifier may cause a toxic gas. Do not burn or break a servo amplifier.
Use the servo amplifier with the specified servo motor.
The electromagnetic brake on the servo motor is designed to hold the motor shaft and should not be used
for ordinary braking.
For such reasons as service life and mechanical structure (e.g. where a ballscrew and the servo motor
are coupled via a timing belt), the electromagnetic brake may not hold the motor shaft. To ensure safety,
install a stopper on the machine side.
(5) Corrective actions
CAUTION
When it is assumed that a hazardous condition may take place at the occur due to a power failure or a
product fault, use a servo motor with electromagnetic brake or an external brake mechanism for the
purpose of prevention.
Configure the electromagnetic brake circuit so that it is activated not only by the servo amplifier signals
but also by an external forced stop (EMG).
Contacts must be open when
servo-on (RYn0) is off, when a trouble Circuit must be
(RX(n+1)A or RX(n+3)A) is present and opened during
when an electromagnetic brake interlock forced stop (EMG).
(MBR).
Servo motor
RA EMG
24VDC
Electromagnetic brake
When any alarm has occurred, eliminate its cause, ensure safety, and deactivate the alarm before
restarting operation.
When power is restored after an instantaneous power failure, keep away from the machine because the
machine may be restarted suddenly (design the machine so that it is secured against hazard if restarted).
A- 5
(6) Maintenance, inspection and parts replacement
CAUTION
With age, the electrolytic capacitor of the servo amplifier will deteriorate. To prevent a secondary accident
due to a fault, it is recommended to replace the electrolytic capacitor every 10 years when used in general
environment.
Please consult our sales representative.
(7) General instruction

To illustrate details, the equipment in the diagrams of this Specifications and Instruction Manual may have
been drawn without covers and safety guards. When the equipment is operated, the covers and safety
guards must be installed as specified. Operation must be performed in accordance with this Specifications
and Instruction Manual.
About processing of waste

When you discard servo amplifier, a battery (primary battery), and other option articles, please follow the law of
each country (area).
FOR MAXIMUM SAFETY

These products have been manufactured as a general-purpose part for general industries, and have not
been designed or manufactured to be incorporated in a device or system used in purposes related to
human life.
Before using the products for special purposes such as nuclear power, electric power, aerospace,
medicine, passenger movement vehicles or underwater relays, contact Mitsubishi.
These products have been manufactured under strict quality control. However, when installing the product
where major accidents or losses could occur if the product fails, install appropriate backup or failsafe
functions in the system.
EEP-ROM life
The number of write times to the EEP-ROM, which stores parameter settings, etc., is limited to 100,000. If
the total number of the following operations exceeds 100,000, the servo amplifier and/or converter unit may
fail when the EEP-ROM reaches the end of its useful life.
Write to the EEP-ROM due to parameter setting changes
Home position setting in the absolute position detection system
Write to the EEP-ROM due to device changes
Write to the EEP-ROM due to point table changes
PRECAUTIONS FOR CHOOSING THE PRODUCTS

Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi;
machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage,
accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other
than Mitsubishi products; and to other duties.
A- 6
COMPLIANCE WITH EC DIRECTIVES
1. WHAT ARE EC DIRECTIVES?
The EC directives were issued to standardize the regulations of the EU countries and ensure smooth
distribution of safety-guaranteed products. In the EU countries, the machinery directive (effective in
January, 1995), EMC directive (effective in January, 1996) and low voltage directive (effective in January,
1997) of the EC directives require that products to be sold should meet their fundamental safety
requirements and carry the CE marks (CE marking). CE marking applies to machines and equipment
into which servo amplifiers have been installed.
(1) EMC directive

The EMC directive applies not to the servo units alone but to servo-incorporated machines and
equipment. This requires the EMC filters to be used with the servo-incorporated machines and
equipment to comply with the EMC directive. For specific EMC directive conforming methods, refer to
the EMC Installation Guidelines (IB(NA)67310).
(2) Low voltage directive

The low voltage directive applies also to servo units alone. Hence, they are designed to comply with
the low voltage directive.
This servo is certified by TUV, third-party assessment organization, to comply with the low voltage
directive.
(3) Machine directive

Not being machines, the servo amplifiers need not comply with this directive.
2. PRECAUTIONS FOR COMPLIANCE

(1) Servo amplifiers and servo motors used
Use the servo amplifiers and servo motors which comply with the standard model.
Servo amplifier series :MR-J2S-10CP-S084 to MR-J2S-700CP-S084

MR-J2S-10CP1-S084 to MR-J2S-40CP1-S084
Servo motor series :HC-KFS
HC-MFS
HC-SFS
HC-RFS
HC-UFS
HA-LFS
HC-LFS
(2) Configuration
Control box
Reinforced
insulating type
Reinforced 24VDC
insulating power
No-fuse Magnetic supply
transformer Servo
breaker contactor
motor
Servo
NFB MC amplifier M
(3) Environment
Operate the servo amplifier at or above the contamination level 2 set forth in IEC60664-1. For this
purpose, install the servo amplifier in a control box which is protected against water, oil, carbon, dust,
dirt, etc. (IP54).
A- 7
(4) Power supply
(a) Operate the servo amplifier to meet the requirements of the overvoltage category II set forth in
IEC60664-1. For this purpose, a reinforced insulating transformer conforming to the IEC or EN
Standard should be used in the power input section.
(b) When supplying interface power from external, use a 24VDC power supply which has been
insulation-reinforced in I/O.
(5) Grounding
(a) To prevent an electric shock, always connect the protective earth (PE) terminals (marked ) of the
servo amplifier to the protective earth (PE) of the control box.
(b) Do not connect two ground cables to the same protective earth (PE) terminal (marked ). Always
connect the cables to the terminals one-to-one.
PE terminals PE terminals
(c) If a leakage current breaker is used to prevent an electric shock, the protective earth (PE) terminals
(marked ) of the servo amplifier must be connected to the corresponding earth terminals.
(6) Wiring
(a) The cables to be connected to the terminal block of the servo amplifier must have crimping
terminals provided with insulating tubes to prevent contact with adjacent terminals.
Crimping terminal
Insulating tube
Cable
(b) Use the servo motor side power connector which complies with the EN Standard. The EN Standard
compliant power connector sets are available from us as options.
(7) Auxiliary equipment and options

(a) The no-fuse breaker and magnetic contactor used should be the EN or IEC standard-compliant
products of the models described in section 15.2.2.
(b) The sizes of the cables described in section 15.2.1 meet the following requirements. To meet the
other requirements, follow Table 5 and Appendix C in EN60204-1.
Ambient temperature: 40 (104) [ ( )]
Sheath: PVC (polyvinyl chloride)
Installed on wall surface or open table tray
(c) Use the EMC filter for noise reduction.
(8) Performing EMC tests

When EMC tests are run on a machine/device into which the servo amplifier has been installed, it
must conform to the electromagnetic compatibility (immunity/emission) standards after it has
satisfied the operating environment/electrical equipment specifications.
For the other EMC directive guidelines on the servo amplifier, refer to the EMC Installation
Guidelines (IB(NA)67310).
A- 8
CONFORMANCE WITH UL/C-UL STANDARD
(1) Servo amplifiers and servo motors used
Use the servo amplifiers and servo motors which comply with the standard model.
Servo amplifier series :MR-J2S-10CP-S084 to MR-J2S-700CP-S084
Servo motor series :HC-KFS
HC-MFS
HC-SFS
HC-RFS
HC-UFS
HA-LFS
HC-LFS
(2) Installation
Install a cooling fan of 100CFM (2.8m3/min) air flow 4 in (10.16 cm) above the servo amplifier or
provide cooling of at least equivalent capability.
(3) Short circuit rating
This servo amplifier conforms to the circuit whose peak current is limited to 5000A or less. Having
been subjected to the short-circuit tests of the UL in the alternating-current circuit, the servo
amplifier conforms to the above circuit.
(4) Capacitor discharge time
The capacitor discharge time is as listed below. To ensure safety, do not touch the charging section for
15 minutes after power-off.
Servo amplifier Discharge time [min]
MR-J2S-10CP(1)-S084 20CP(1)-S084 1
MR-J2S-40CP(1)-S084 60CP-S084 2
MR-J2S-70CP-S084 to 350CP-S084 3
MR-J2S-500CP-S084 700CP-S084 5
(5) Options and auxiliary equipment

Use UL/C-UL standard-compliant products.
(6) Attachment of a servo motor

For the flange size of the machine side where the servo motor is installed, refer to “CONFORMANCE
WITH UL/C-UL STANDARD” in the Servo Motor Instruction Manual.
(7) About wiring protection

For installation in United States, branch circuit protection must be provided, in accordance with the
National Electrical Code and any applicable local codes.
For installation in Canada, branch circuit protection must be provided, in accordance with the Canada
Electrical Code and any applicable provincial codes.
<<About the manuals>>
This Instruction Manual and the MELSERVO Servo Motor Instruction Manual are required if you use
the MR-J2S-CP-S084 for the first time. Always purchase them and use the MR-J2S-CP-S084 safely.
Relevant manuals
Manual name Manual No.
MELSERVO-J2-Super Series To Use the AC Servo Safely IB(NA)0300010
MELSERVO Servo Motor Instruction Manual SH(NA)3181
EMC Installation Guidelines IB(NA)67310
A- 9
MEMO
A - 10
CONTENTS
1. FUNCTIONS AND CONFIGURATION 1- 1 to 1-28
1.1 Introduction.............................................................................................................................................. 1- 1
1.1.1 Features of CC-Link communication functions............................................................................. 1- 1
1.1.2 Function block diagram ................................................................................................................... 1- 2
1.1.3 System configuration........................................................................................................................ 1- 4
1.2 Servo amplifier standard specifications ................................................................................................ 1- 7
1.3 Function list ............................................................................................................................................. 1- 9
1.4 Model code definition ............................................................................................................................. 1-11
1.5 Combination with servo motor.............................................................................................................. 1-13
1.6 Structure.................................................................................................................................................. 1-14
1.6.1 Part names of servo amplifier ........................................................................................................ 1-14
1.6.2 Part name of CC-Link unit ............................................................................................................. 1-18
1.6.3 Removal and reinstallation of the front cover .............................................................................. 1-19
1.7 Servo system with auxiliary equipment............................................................................................... 1-21
1.8 Flowchart of Operation Method ............................................................................................................ 1-26
2. INSTALLATION 2- 1 to 2- 4
2.1 Environmental conditions....................................................................................................................... 2- 1

2.2 Installation direction and clearances .................................................................................................... 2- 2
2.3 Keep out foreign materials ..................................................................................................................... 2- 3
2.4 Cable stress .............................................................................................................................................. 2- 4
3. CC-Link COMMUNICATION FUNCTIONS 3- 1 to 3-56
3.1 Communication specifications................................................................................................................ 3- 1

3.2 System configuration............................................................................................................................... 3- 2
3.2.1 Configuration example..................................................................................................................... 3- 2
3.2.2 Wiring method .................................................................................................................................. 3- 3
3.2.3 Station number setting .................................................................................................................... 3- 5
3.2.4 Communication baud rate setting .................................................................................................. 3- 6
3.2.5 Occupied station count setting ........................................................................................................ 3- 6
3.3 Functions .................................................................................................................................................. 3- 7
3.3.1 Function block diagram ................................................................................................................... 3- 7
3.3.2 Functions ........................................................................................................................................... 3- 7
3.4 Servo amplifier setting............................................................................................................................ 3- 8
3.5 I/O signals transferred to/from the programmable controller CPU ................................................... 3- 9
3.5.1 I/O signals.......................................................................................................................................... 3- 9
3.5.2 Detailed explanation of I/O signals................................................................................................ 3-12
3.5.3 Monitor codes ................................................................................................................................... 3-24
3.5.4 Instruction codes (RWwn+2 RWwn+3) ....................................................................................... 3-25
3.5.5 Answer codes (RWrn+2).................................................................................................................. 3-32
3.5.6 Setting the CN1A CN1B external input signals ........................................................................ 3-33
3.6 Data communication timing charts ...................................................................................................... 3-34
3.6.1 Monitor codes ................................................................................................................................... 3-34
3.6.2 Instruction codes.............................................................................................................................. 3-36
1
3.6.3 Remote register-based position/speed setting............................................................................... 3-38
3.7 Function-by-function programming examples .................................................................................... 3-41
3.7.1 System configuration example ....................................................................................................... 3-41
3.7.2 Reading the servo amplifier status ................................................................................................ 3-42
3.7.3 Writing the operation commands................................................................................................... 3-43
3.7.4 Reading the data.............................................................................................................................. 3-44
3.7.5 Writing the data............................................................................................................................... 3-46
3.7.6 Operation .......................................................................................................................................... 3-49
3.8 Continuous operation program example.............................................................................................. 3-52
3.8.1 System configuration example when 1 station is occupied ......................................................... 3-52
3.8.2 Program example when 1 station is occupied............................................................................... 3-53
3.8.3 System configuration example when 2 stations are occupied ..................................................... 3-54
3.8.4 Program example when 2 stations are occupied .......................................................................... 3-55
4. SIGNALS AND WIRING 4- 1 to 4-36
4.1 Standard connection example ................................................................................................................ 4- 2

4.2 Internal connection diagram of servo amplifier ................................................................................... 4- 4
4.3 I/O signals................................................................................................................................................. 4- 5
4.3.1 Connectors and signal arrangements ............................................................................................. 4- 5
4.3.2 Signal (devices) explanations .......................................................................................................... 4- 6
4.4 Detailed description of signals (devices) ............................................................................................... 4- 8
4.4.1 Forward rotation start Reverse rotation start Temporary stop/Restart................................. 4- 8
4.4.2 Movement finish Rough match In position................................................................................ 4- 9
4.4.3 Torque limit...................................................................................................................................... 4-11
4.5 Alarm occurrence timing chart ............................................................................................................. 4-12
4.6 Interfaces................................................................................................................................................. 4-13
4.6.1 Common line .................................................................................................................................... 4-13
4.6.2 Detailed description of the interfaces ............................................................................................ 4-14
4.7 Input power supply circuit..................................................................................................................... 4-17
4.7.1 Connection example ........................................................................................................................ 4-17
4.7.2 Terminals.......................................................................................................................................... 4-19
4.7.3 Power-on sequence........................................................................................................................... 4-20
4.8 Connection of servo amplifier and servo motor ................................................................................... 4-22
4.8.1 Connection instructions .................................................................................................................. 4-22
4.8.2 Connection diagram ........................................................................................................................ 4-22
4.8.3 I/O terminals .................................................................................................................................... 4-24
4.9 Servo motor with electromagnetic brake ............................................................................................. 4-26
4.10 Grounding ............................................................................................................................................. 4-30
4.11 Servo amplifier terminal block (TE2) wiring method ....................................................................... 4-31
4.11.1 For the servo amplifier produced later than Jan. 2006 ............................................................. 4-31
4.11.2 For the servo amplifier produced earlier than Dec. 2005.......................................................... 4-33
4.12 Instructions for the 3M connector....................................................................................................... 4-35
5. OPERATION 5- 1 to 5-46
5.1 When switching power on for the first time.......................................................................................... 5- 1

5.1.1 Pre-operation checks ........................................................................................................................ 5- 1
5.1.2 Startup ............................................................................................................................................... 5- 2
5.2 Automatic operation mode...................................................................................................................... 5- 5
2
5.2.1 What is automatic operation mode? ............................................................................................... 5- 5
5.2.2 Automatic operation using point table ........................................................................................... 5- 7
5.2.3 Remote register-based position/speed setting............................................................................... 5-17
5.3 Manual operation mode ......................................................................................................................... 5-23
5.4 Manual home position return mode ..................................................................................................... 5-25
5.4.1 Outline of home position return ..................................................................................................... 5-25
5.4.2 Dog type home position return ....................................................................................................... 5-27
5.4.3 Count type home position return ................................................................................................... 5-29
5.4.4 Data setting type home position return ........................................................................................ 5-31
5.4.5 Stopper type home position return ................................................................................................ 5-32
5.4.6 Home position ignorance (servo-on position defined as home position)..................................... 5-34
5.4.7 Dog type rear end reference home position return....................................................................... 5-35
5.4.8 Count type front end reference home position return.................................................................. 5-37
5.4.9 Dog cradle type home position return ........................................................................................... 5-39
5.4.10 Home position return automatic return function....................................................................... 5-41
5.4.11 Automatic positioning function to the home position ................................................................ 5-42
5.5 Absolute position detection system....................................................................................................... 5-43
6. PARAMETERS 6- 1 to 6-26
6.1 Parameter list .......................................................................................................................................... 6- 1

6.1.1 Parameter write inhibit ................................................................................................................... 6- 1
6.1.2 List ..................................................................................................................................................... 6- 2
6.2 Detailed explanation .............................................................................................................................. 6-24
6.2.1 Electronic gear ................................................................................................................................. 6-24
6.2.2 Changing the status display screen............................................................................................... 6-25
6.2.3 S-pattern acceleration/deceleration ............................................................................................... 6-25
6.2.4 Changing the stop pattern using a limit switch ........................................................................... 6-26
6.2.5 Alarm history clear.......................................................................................................................... 6-26
6.2.6 Rough match output ........................................................................................................................ 6-26
6.2.7 Software limit................................................................................................................................... 6-26
7. MR Configurator (SERVO CONFIGURATION SOFTWARE) 7- 1 to 7-20
7.1 Specifications ........................................................................................................................................... 7- 1

7.2 System configuration............................................................................................................................... 7- 1
7.3 Station setting.......................................................................................................................................... 7- 3
7.4 Parameters ............................................................................................................................................... 7- 4
7.5 Point table ................................................................................................................................................ 7- 6
7.6 Device assignment method ..................................................................................................................... 7- 8
7.7 Test operation ......................................................................................................................................... 7-12
7.7.1 Jog operation .................................................................................................................................... 7-12
7.7.2 Positioning operation....................................................................................................................... 7-14
7.7.3 Motor-less operation ........................................................................................................................ 7-16
7.7.4 Output signal (DO) forced output .................................................................................................. 7-17
7.7.5 Single-step feed ................................................................................................................................ 7-18
7.8 Alarm history .......................................................................................................................................... 7-20
3
8. DISPLAY AND OPERATION 8- 1 to 8-24
8.1 Display flowchart..................................................................................................................................... 8- 1

8.1.1 Display flowchart from powering ON to OFF................................................................................ 8- 1
8.1.2 Display mode transition................................................................................................................... 8- 2
8.2 Status display .......................................................................................................................................... 8- 3
8.2.1 Display transition ............................................................................................................................. 8- 3
8.2.2 Display examples .............................................................................................................................. 8- 4
8.2.3 Status display list ............................................................................................................................. 8- 5
8.3 Diagnosis mode ........................................................................................................................................ 8- 6
8.3.2 Diagnosis mode list........................................................................................................................... 8- 7
8.4 Alarm mode .............................................................................................................................................. 8- 9
8.4.2 Alarm mode list................................................................................................................................ 8-10
8.5 Point table mode ..................................................................................................................................... 8-12
8.5.1 Point table transition ...................................................................................................................... 8-12
8.5.2 Point table mode setting screen sequence..................................................................................... 8-13
8.5.3 Operation method ............................................................................................................................ 8-14
8.6 Parameter mode ..................................................................................................................................... 8-16
8.6.1 Parameter mode transition............................................................................................................. 8-16
8.6.2 Operation example .......................................................................................................................... 8-17
8.7 External I/O signal display.................................................................................................................... 8-19
8.8 Output signal (DO) forced output ......................................................................................................... 8-20
8.9 Test operation mode ............................................................................................................................... 8-21
8.9.1 Mode change..................................................................................................................................... 8-21
8.9.2 Jog operation .................................................................................................................................... 8-22
8.9.3 Positioning operation....................................................................................................................... 8-23
8.9.4 Motor-less operation ........................................................................................................................ 8-24
9. GENERAL GAIN ADJUSTMENT 9- 1 to 9-12
9.1 Different adjustment methods ............................................................................................................... 9- 1

9.1.1 Adjustment on a single servo amplifier.......................................................................................... 9- 1
9.1.2 Adjustment using MR Configurator (servo configuration software) ........................................... 9- 2
9.2 Auto tuning .............................................................................................................................................. 9- 3
9.2.1 Auto tuning mode ............................................................................................................................. 9- 3
9.2.2 Auto tuning mode operation ............................................................................................................ 9- 4
9.2.3 Adjustment procedure by auto tuning............................................................................................ 9- 5
9.2.4 Response level setting in auto tuning mode .................................................................................. 9- 6
9.3 Manual mode 1 (simple manual adjustment)....................................................................................... 9- 7
9.3.1 Operation of manual mode 1 ........................................................................................................... 9- 7
9.3.2 Adjustment by manual mode 1 ....................................................................................................... 9- 7
9.4 Interpolation mode ................................................................................................................................. 9-10
9.5 Differences in auto tuning between MELSERVO-J2 and MELSERVO-J2-Super .......................... 9-11
9.5.1 Response level setting ..................................................................................................................... 9-11
9.5.2 Auto tuning selection....................................................................................................................... 9-11
4
10. SPECIAL ADJUSTMENT FUNCTIONS 10- 1 to 10-10
10.1 Function block diagram ...................................................................................................................... 10- 1

10.2 Machine resonance suppression filter ............................................................................................... 10- 1
10.3 Adaptive vibration suppression control ............................................................................................ 10- 3
10.4 Low-pass filter ..................................................................................................................................... 10- 4
10.5 Gain changing function....................................................................................................................... 10- 5
10.5.1 Applications................................................................................................................................... 10- 5
10.5.2 Function block diagram ............................................................................................................... 10- 5
10.5.3 Parameters .................................................................................................................................... 10- 6
10.5.4 Gain changing operation.............................................................................................................. 10- 8
11. INSPECTION 11- 1 to 11- 2
12. TROUBLESHOOTING 12- 1 to 12-14
12.1 Trouble at start-up .............................................................................................................................. 12- 1

12.2 Operation at error occurrence ............................................................................................................ 12- 2
12.3 CC-Link communication error ........................................................................................................... 12- 3
12.4 When alarm or warning has occurred ............................................................................................... 12- 3
12.4.1 Alarms and warning list .............................................................................................................. 12- 4
12.4.2 Remedies for alarms..................................................................................................................... 12- 5
12.4.3 Remedies for warnings................................................................................................................ 12-12
13. OUTLINE DIMENSION DRAWINGS 13- 1 to 13- 8
13.1 Servo amplifiers................................................................................................................................... 13- 1

13.2 CC-Link option unit (MR-J2S-T01) ................................................................................................... 13- 5
13.3 Connectors............................................................................................................................................ 13- 6
14. CHARACTERISTICS 14- 1 to 14- 8
14.1 Overload protection characteristics ................................................................................................... 14- 1

14.2 Power supply equipment capacity and generated loss .................................................................... 14- 2
14.3 Dynamic brake characteristics........................................................................................................... 14- 4
14.3.1 Dynamic brake operation............................................................................................................. 14- 4
14.3.2 The dynamic brake at the load inertia moment ........................................................................ 14- 6
14.4 Encoder cable flexing life .................................................................................................................... 14- 7
14.5 Inrush currents at power-on of main circuit and control circuit .................................................... 14- 7
15. OPTIONS AND AUXILIARY EQUIPMENT 15- 1 to 15-44
15.1 Options.................................................................................................................................................. 15- 1

15.1.1 Regenerative options .................................................................................................................... 15- 1
15.1.2 FR-BU2 brake unit ....................................................................................................................... 15- 8
15.1.3 Power regeneration converter .................................................................................................... 15-14
15.1.4 Cables and connectors................................................................................................................. 15-17
15.1.5 Junction terminal block (MR-TB20) .......................................................................................... 15-25
5
15.1.6 Battery (MR-BAT, A6BAT)......................................................................................................... 15-26
15.2 Auxiliary equipment .......................................................................................................................... 15-27
15.2.1 Recommended wires.................................................................................................................... 15-27
15.2.2 No-fuse breakers, fuses, magnetic contactors........................................................................... 15-30
15.2.3 Power factor improving reactors ................................................................................................ 15-31
15.2.4 Relays............................................................................................................................................ 15-32
15.2.5 Surge absorbers ........................................................................................................................... 15-32
15.2.6 Noise reduction techniques......................................................................................................... 15-33
15.2.7 Leakage current breaker ............................................................................................................ 15-40
15.2.8 EMC filter..................................................................................................................................... 15-42
APPENDIX App- 1 to App- 4
App 1. Status indication block diagram ................................................................................................. App- 1

App 2. Junction terminal block (MR-TB20) terminal block labels ...................................................... App- 2
App 3. Combination of servo amplifier and servo motor ...................................................................... App- 3
App 4. Change of connector sets to the RoHS compatible products .................................................... App- 4
6
1. FUNCTIONS AND CONFIGURATION
1.1 Introduction
When used with the MR-J2S-T01 CC-Link option unit, the MR-J2S- CP-S084 CC-Link compatible servo
amplifier can support the CC-Link communication functions. Up to 42 axes of servo amplifiers can be
controlled/monitored from the programmable controller side.
As the servo, it is based on the MR-J2S-CP AC servo amplifier with built-in positioning functions and has
the function to perform positioning operation by merely setting the position data (target positions), servo
motor speeds, acceleration and deceleration time constants, etc. to point tables as if setting them in
parameters. The servo amplifier is the most appropriate to configure a program-free, simple positioning
system or to simplify a system, for example.
There are 3 points of point tables as standard, and they can be increased up to 31 points by using the
optional MR Configurator (servo configuration software).
All servo motors are equipped with an absolute position encoder as standard. An absolute position
detection system can be configured by merely adding a battery to the servo amplifier. Once the home
position has been set, home position return is not required at power on, alarm occurrence, etc.
The MR-J2S-CP-S084 is made easier to use and higher in function by using it with the MR Configurator
(servo configuration software).
1.1.1 Features of CC-Link communication functions
(1) Fast communication

Fast communication can be made by cyclic transmission of not only bit data but also word data.
(a) The highest communication speed is 10Mbps.
(b) The broadcast polling system ensures as high as 3.9ms to 6.7ms even at the maximum link scan
(10Mbps).
(2) Variable communication speed/distance system

Selection of speed/distance allows use in a wide range of areas from a system requiring high speed to a
system requiring long distance.
(3) System fault prevention (station separating function)

Because of connection in the bus system, any remote or local station that has become faulty due to
power-off or the like does not affect communications with normal remote and local stations.
In addition, use of the two-piece terminal block allows the unit to be changed during data link.
(4) Factory Automation compatible

As the remote device stations of CC-Link, the servo amplifiers share a link system and can be
controlled/monitored with programmable controller user programs.
From the programmable controller side, the running speed, acceleration/deceleration time constant
and other settings of servo motors can be changed/checked and the servo motors started and stopped.
1- 1
1.1.2 Function block diagram
The function block diagram of this servo is shown below.

(1) MR-J2S-350CP-S084 or less
Regenerative option
Servo amplifier P C D Servo motor

Diode
NFB (Note 1)
stack Relay
MC L1 U U
(Note 2)
L2 Regenerative Current V V
Power transistor M
detector
supply L3 W W
CHARGE
lamp
(Note 3) Cooling fan Dynamic

brake
L11 B1
Control Electro-
L21 power magnetic
supply B2
brake
Base Voltage Overcurrent Current
CN2
amplifier detection protection detection
Encoder
Current
control
Point table
Model adaptive control
Acceleration Deceleration
No. Position Speed time time Dwell Auxiliary
data constant constant
1 1000 1000 80 80 0 0
Speed
control 2 2000 2000 100 100 0 0
3 4000 2000 70 60 500 1
4 500 2000 60 70 1000 1
5 1000 2000 80 80 0 0
Position 6 2000 1000 80 80 0 0
control
7 1000 1000 80 80 0
8 1000 1000 100 100 0 0
1000 100 100 0 0
31 2000 2000 80 80 0 0
Position MR-BAT
command
CON1
creation
Optional battery
(for absolute position
I/F detection system)
CN1A CN1B CN3
DI/O Control CN30 Controller

Servo on
CN40
MR-J2S-T01
Start option unit RS-232C/RS-422
Failure, etc
CN10
CC-Link
Note 1. The built-in regenerative resistor is not provided for the MR-J2S-10CP (1)-S084.
2. For 1-phase 230VAC, connect the power supply to L1, L2 and leave L3 open. Refer to section 1.2 for the power supply
specification. L3 is not provided for a 1-phase 100 to120VAC power supply.
3. Servo amplifiers MR-J2S-200CP-S084 have a cooling fan.
1- 2
(2) MR-J2S-500CP-S084 700CP-S084

Regenerative option
Servo amplifier P C N Servo motor

Diode
NFB stack Relay
MC L1 U U
(Note)
L2 Regenerative Current V V
Power M
transistor detector
supply L3 W W
CHARGE
lamp
Cooling fan Dynamic

brake
L11 B1
Control Electro-
L21 power magnetic
supply B2
brake
Base Voltage Overcurrent Current
CN2
amplifier detection protection detection
Encoder
Current
control
Point table
Model adaptive control
Acceleration Deceleration
No. Position Speed time time Dwell Auxiliary
data constant constant
1 1000 1000 80 80 0 0
Speed
control 2 2000 2000 100 100 0 0
3 4000 2000 70 60 500 1
4 500 2000 60 70 1000 1
5 1000 2000 80 80 0 0
Position 6 2000 1000 80 80 0 0
control
7 1000 1000 80 80 0
8 1000 1000 100 100 0 0
1000 100 100 0 0
31 2000 2000 80 80 0 0
Position MR-BAT
command
CON1
creation
Optional battery
(for absolute position
detection system)
I/F
CN1A CN1B CN3
DI/O Control CN30 Controller

Servo on
CN40
MR-J2S-T01
Start option unit RS-232C/RS-422
Failure, etc
CN10
CC-Link
Note. Refer to section 1.2 for the power supply specification.
1- 3
1.1.3 System configuration
This section provides operations using this servo.

Use of CC-Link enables you to freely configure any system from a single-axis system to an up to 42-axis
system. Further, you can assign external input signals to the pins of the connector CN1A and CN1B by
setting parameter No. 116 to 118 and parameter No. 79 to 83.
Set the following values to the point table.
Name Setting range Unit

0.001[mm]
0.01[mm]
Position data 999999 to 999999
0.1[mm]
1[mm]
Servo motor speed 0 to max. speed [r/min]
Acceleration time constant 0 to 20000 [ms]
Deceleration time constant 0 to 20000 [ms]
Dwell 0 to 20000 [ms]
0 to 3
Auxiliary function
(Refer to section 5.2)
Up to 31 points can be set to the point table.
1- 4
(1) Operation using CC-Link communication functions

(a) Operation
All signals can be controlled by CC-Link communication. Also, each point table setting, point table
selection, parameter value change, setting, monitor, servo motor operation and others can be
performed.
(b) Configuration
Programmable controller
CC-Link master unit
Servo amplifier Option unit

(Axis 1) MR-J2S-T01
CN10
CN1A
CN1B
CN2 CN3 CN30
Power supply
CN40
Servo motor CC-Link
Servo amplifier Option unit

(Axis 2) MR-J2S-T01
CN10
CN1A
CN1B
CN2 CN3 CN30

Power supply
CN40
To the next axis
Servo motor
1- 5
(2) Operation using CC-Link communication functions and external input signals
(a) Operation
Using parameter No. 116 to 118 and parameter No. 79 to 83, input signals can be assigned to the
external input signals of CN1A and CN1B. The signals assigned to the external input signals
cannot be used with the CC-Link communication functions. Output signals can be used with the
CN1A and CN1B connectors and CC-Link communication functions simultaneously.
(b) Configuration
CC-Link master unit
External I/O
signal Servo amplifier Option unit
(Axis 1) MR-J2S-T01
CN10
CN1A
CN1B
CN2 CN3 CN30

Power supply
CN40
Servo motor
CC-Link
External I/O
signal Servo amplifier Option unit
(Axis 2) MR-J2S-T01
CN10
CN1A
CN1B
CN2 CN3 CN30

Power supply
CN40 To the next axis
Servo motor
1- 6
1.2 Servo amplifier standard specifications
POINT
Refer to section 3.1 for the specifications of the CC-Link communication
functions.
Servo amplifier
MR-J2S- -S084 10CP 20CP 40CP 60CP 70CP 100CP 200CP 350CP 500CP 700CP 10CP1 20CP1 40CP1
Item
3-phase 200 to 230VAC, 50/60Hz 1-phase 100 to
Voltage/frequency 3-phase 200 to 230VAC, 50/60Hz
or 1-phase 230VAC, 50/60Hz 120VAC 50/60Hz
Power supply
3-phase 200 to 230VAC:

1-phase
Permissible voltage fluctuation 170 to 253VAC 3-phase 170 to 253VAC
85 to 127VAC
1-phase 230VAC: 207 to 253VAC
Permissible frequency fluctuation Within 5%
Power supply capacity Refer to section14.2
Inrush current Refer to section 14.5
Control system Sine-wave PWM control, current control system
Dynamic brake Built-in
Overcurrent shut-off, regenerative overvoltage shut-off, overload shut-off (electronic
thermal relay), servo motor overheat protection, encoder error protection, regenerative
Protective functions
brake error protection, undervoltage, instantaneous power failure protection, overspeed
protection, excessive error protection
Operational Positioning by specifying the point table No. (31 points)
specifications
Position command Set in point table. 1-point feed length setting range: 1[ m] to 999.999[mm]
Point table
input
number
Speed command Set in point table. Acceleration/deceleration time is set in point table.
input
input S-pattern acceleration/deceleration time constant is set in parameter No.14.
Command system
Signed absolute value command system, incremental value command system, signed
System
absolute value command/incremental value command specifying system
Operational Remote register setting is used for positioning.
Position specifications
command Position command Remote register is used to set position command data.
data input input Feed length input setting range: 1 m to 999.999m
(when 2 Remote register is used to make selection from point table.
Speed command
stations Remote register is used to set speed command data (speed).
input
are S-pattern acceleration/deceleration time constant is set in parameter No.14.
occupied) Signed absolute value command system, incremental value command system, signed
System
absolute value command/incremental value command specifying system
Point table number input, position data input system
Automatic Point table Positioning operation is performed once in accordance with the position and speed
Operation mode
operation commands.
mode Automatic continuous Varied speed operation (2 to 31 speeds), automatic continuous positioning operation (2 to
operation 31 points)
Manual Jog operation is performed in accordance with the parameter-set speed command by
operation Jog contact input or through CC-Link communication function.
mode
1- 7
Servo amplifier
MR-J2S- -S084 10CP 20CP 40CP 60CP 70CP 100CP 200CP 350CP 500CP 700CP 10CP1 20CP1 40CP1
Item
Home position return is made starting with Z-phase pulse after passage of proximity dog.
Home position address may be set. Home position shift distance may be set. Home position
Dog type
return direction may be selected.
Automatic at-dog home position return return/automatic stroke return function
Home position return is made by counting encoder pulses after contact with proximity dog.
Home position address may be set. Home position shift value may be set. Home position
Count type
return direction may be set.
Home position return is made without dog.
Data setting type Home position may be set at any position by manual operation, etc. Home position address
may be set.
Home position return is made by pressing machine part against stroke end.
Stopper type
Home position address may be set. Home position return direction may be set.
Manual
Home position Position where servo-on (RYn0) is switched on is defined as home position.
home
Operation mode
ignorance Home position address may be set.

position
(Servo-on position as
return
home position)
mode
Home position return is made with respect to the rear end of a proximity dog.
Dog type rear end Home position address may be set. Home position shift value may be set. Home position
reference return direction may be set.
Home position return is made with respect to the front end of a proximity dog.
Count type front end Home position address may be set. Home position shift value may be set. Home position
reference return direction may be set.
Home position return is made with respect to the front end of a proximity dog by the first
Z-phase pulse.
Dog cradle type Home position address may be set. Home position shift value may be set. Home position
return direction may be set.
Automatic positioning to home High-speed automatic return to a defined home position.
position
Absolute position detection, backlash function
Other functions Overtravel prevention using external limit switch
Software stroke limit
Self-cooled,
Structure Self-cooled, open (IP00) Force-cooling, open (IP00)
open (IP00)
[ ] 0 to 55 (non-freezing)
In operation
Ambient [ ] 32 to 131 (non-freezing)
temperature [ ] 20 to 65 (non-freezing)
In storage
Environment
Ambient In operation 90%RH or less (non-condensing)

humidity In storage
Indoors (no direct sunlight)
Ambient
Free from corrosive gas, flammable gas, oil mist, dust and dirt
Altitude Max. 1000m (3280ft) above sea level
5.9 [m/s2] or less
Vibration
19.4 [ft/s2] or less
[kg] 0.7 0.7 1.1 1.1 1.7 1.7 2.0 2.0 4.9 7.2 0.7 0.7 1.1
Mass
[lb] 1.5 1.5 2.4 2.4 3.75 3.75 4.4 4.4 10.8 15.87 1.5 1.5 2.4
1- 8
1.3 Function list
The following table lists the functions of this servo. For details of the functions, refer to the reference field.
Function Description Reference
Select the required ones from among 31 preset point tables and
perform operation in accordance with the set values.
Positioning by automatic operation Section 5.2
Use the external input signal or communication function to choose
the point tables.
Servo motor speed can be varied continuously until the preset Section 5.2.2
Varied speed operation
moving distance is reached. (Max. set speeds: 31 speeds) (4)(b)
By merely choosing one point table and starting operation,
Automatic continuous positioning
positioning can be executed continuously in accordance with Section 5.2.2 (4)
operation
several point tables.
Dog type, count type, data setting type, stopper type, home
Manual home position return position ignorance, dog type rear end reference, count type front Section 5.4
end reference, dog cradle type
High-resolution encoder of 131072 pulses/rev is used as a servo
High-resolution encoder
motor encoder.
By merely setting the home position once, home position return
Absolute position detection system Section 5.5
need not be done at each power on.
You can switch between gains during rotation and gains during
Gain changing function Section 10.5
stop or use an external signal to change gains during operation.
Servo amplifier detects mechanical resonance and sets filter
Adaptive vibration suppression control Section 10.3
characteristics automatically to suppress mechanical vibration.
Suppresses high-frequency resonance which occurs as servo
Low-pass filter Section 10.4
system response is increased.
Analyzes the frequency characteristic of the mechanical system by
Machine analyzer function simply connecting a MR Configurator (servo configuration
software)-installed personal computer and servo amplifier.
Can simulate machine motions on a personal computer screen on
Machine simulation
the basis of the machine analyzer results.
Personal computer changes gains automatically and searches for
Gain search function
overshoot-free gains in a short time.
Slight vibration suppression control Vibration of 1 pulse at servo motor stop is suppressed. Parameter No. 20
The electronic gear is used to make adjustment so that the servo
amplifier setting matches the machine moving distance. Also,
Electronic gear changing the electronic gear value allows the machine to be moved Section 6.2.1
at any multiplication ratio to the moving distance using the servo
amplifier.
Automatically adjusts the gain to optimum value if load applied to
Auto tuning the servo motor shaft varies. Higher in performance than MR-J2 Section 9.2
series servo amplifier.
S-pattern acceleration/deceleration time
Acceleration/deceleration can be made smoothly. Section 6.2.3
constant
Used when the built-in regenerative resistor of the servo amplifier
Regenerative option does not have sufficient regenerative capability for the Section 15.1.1
regenerative power generated.
Used when the regenerative option cannot provide enough
Brake unit regenerative power. Section 15.1.2
Can be used with the servo amplifier of 5kW or more.
Used when the regenerative option cannot provide enough
Regeneration converter regenerative power. Section 15.1.3
Can be used with the servo amplifier of 5kW or more.
1- 9
Function Description Reference

By using the MR Configurator (Servo configuration Software), the
Alarm history current alarm and five past alarm numbers are stored and Section 7.8
displayed.
By changing the parameter setting or using the MR Configurator Parameter No.78 to 83
(Servo Configuration Software), any devices can be assigned to 9 Parameter No.88 to 90
I/O signal selection (Device setting) input, 5 output and 1 I/O pins. Parameter No.116
to 118
Section 7.6
Servo motor-torque is limited.
Torque limit Section 4.4.3
Parameter 2 limit value
Status display The servo status is displayed. Section 8.2
Jog operation, positioning operation, motor-less operation, DO
Test operation mode Section 7.7
forced output, 1-step feed
The servo motor travel region can be limited using the forward
Limit switch Section 6.2.4
rotation stroke end (LSP)/reverse rotation stroke end (LSN).
The travel region is limited using parameters in terms of address.
Software limit The function similar to that of a limit switch is limited by Section 6.2.7
parameter.
1 - 10
1.4 Model code definition
(1) Rating plate

(a) Servo amplifier
MITSUBISHI AC SERVO Model

MODEL MR-J2S-60CP-S084 Capacity
POWER : 600W
INPUT : 3.2A 3PH+1PH200-230V 50Hz Applicable power supply
3PH+1PH200-230V 60Hz
5.5A 1PH230V 50/60Hz
OUTPUT: 170V 0-360Hz 3.6A Rated output current
SERIAL : A5*******
TC3**AAAAG52 Serial number
PASSED
MITSUBISHI ELECTRIC CORPORATION
MADE IN JAPAN
MR-J2S-100CP-S084 or less MR-J2S-200CP-S084 350CP-S084
Rating plate
Rating plate
MR-J2S-500CP-S084 MR-J2S-700CP-S084
Rating plate
Rating plate
(b) CC-Link option unit

MR-J2S-T01
MITSUBISHI AC SERVO
MODEL
MR-J2S-T01 Model
TC350A072G51 PASSED Rating plate

MITSUBISHI ELECTRIC CORPORATION
MADE IN JAPAN
1 - 11
(2) Model of servo amplifier

MR–J2S– CP –S084
Series
Power Supply
Symbol Power supply
3-phase 200 to 230VAC

None
(Note1) 1-phase 230VAC
(Note2)
1-phase 100V to 120VAC
1
Note 1. 1-phase 230V is supported
by 750W or less.
2. 1-phase 100V to 120V is
supported by 400W or less.
Built-in positioning functions
Rated output
Rated Rated
Symbol Symbol
output [W] output [W]
10 100 100 1000
20 200 200 2000
40 400 350 3500
60 600 500 5000
70 750 700 7000
1 - 12
1.5 Combination with servo motor
The following table lists combinations of servo amplifiers and servo motors. The same combinations apply
to the models with electromagnetic brakes and the models with reduction gears.
Servo motors
Servo amplifier HC-SFS HC-UFS
HC-KFS HC-MFS HC-RFS
1000r/min 2000r/min 3000r/min 2000r/min 3000r/min
MR-J2S-10CP(1)-S084 053 13 053 13 13
MR-J2S-20CP(1)-S084 23 23 23
MR-J2S-40CP(1)-S084 43 43 43
MR-J2S-60CP-S084 52 53
MR-J2S-70CP-S084 73 73 72 73
MR-J2S-100CP-S084 81 102 103
MR-J2S-200CP-S084 121 201 152 202 153 203 103 153 152
MR-J2S-350CP-S084 301 352 353 203 202
MR-J2S-500CP-S084 502 353 503 352 502
MR-J2S-700CP-S084 702
Servo motors
Servo amplifier HA-LFS
HC-LFS
1000r/min 1500r/min 2000r/min
MR-J2S-60CP-S084 52
MR-J2S-100CP-S084 102
MR-J2S-200CP-S084 152
MR-J2S-350CP-S084 202
MR-J2S-500CP-S084 502 302
MR-J2S-700CP-S084 601 (Note) 701M (Note) 702
Note. Consult us since the servo amplifier to be used with any of these servo motors is optional.
1 - 13
1.6 Structure
1.6.1 Part names of servo amplifier

Name/Application Reference
Battery holder
Section5.5
Contains the battery for absolute position data backup.
Battery connector (CON1)

Used to connect the battery for absolute position data Section5.5
backup.
Display
The 5-digit, seven-segment LED shows the servo Chapter8
status and alarm number.
Operation section
Used to perform status display, diagnostic, alarm,
parameter and point table setting operations.
MODE UP DOWN SET
MODE UP DOWN SET
Used to set data. Chapter8
Used to change the

display or data in each
mode.
Used to change the

mode.
I/O signal connector (CN1A)

Section4.3
Used to connect digital I/O signals.
I/O signal connector (CN1B)

Section4.3
MR-J2S-T01 connector (CN3)

Chapter7
Connector for connection of the MR-J2S-T01 CC-Link
Section15.1.4
option unit.
Rating plate Section1.4
Charge lamp
Lit to indicate that the main circuit is charged. While
this lamp is lit, do not reconnect the cables.
Encoder connector (CN2) Section4.3

Used to connect the servo motor encoder. Section15.1.4
Main circuit terminal block (TE1)

Section4.7.2
Used to connect the input power supply and servo
Section13.1
motor.
Control circuit terminal block (TE2) Section4.7.2

Used to connect the control circuit power supply and Section13.1
regenerative option. Section15.1.1
Protective earth (PE) terminal ( ) Section4.10

Ground terminal. Section13.1
Fixed part (2 places)
(For MR-J2S-70CP-S084
100CP-S084 3 places)
1 - 14
(2) MR-J2S-200CP-S084 MR-J2S-350CP-S084
POINT
This servo amplifier is shown without the front cover. For removal of the
front cover, refer to section 1.6.3.
Battery holder
Section5.5

backup.
Display
Operation section
Used to perform status display, diagnostic, alarm,
MODE UP DOWN SET
MODE UP DOWN SET
Used to set data. Chapter8
Used to change the

mode.
Used to change the

mode.

Section4.3

Section4.3

Chapter7
Section15.1.4
option unit.
Charge lamp
Lit to indicate that the main circuit is charged. While
this lamp is lit, do not reconnect the cables.

Main circuit terminal block (TE1)

Section4.7.2
Used to connect the input power supply and servo
Section13.1
motor.

Used to connect the control circuit power supply and Section13.1
regenerative option. Section15.1.1
Cooling fan Protective earth (PE) terminal ( ) Section4.10

Fixed part (4 places)
1 - 15
(3) MR-J2S-500CP-S084
POINT
The servo amplifier is shown without the front cover. For removal of the

backup.
Battery holder
Section5.5
Display
Operation section
MODE UP DOWN SET Used to perform status display, diagnostic, alarm,
MODE UP DOWN SET
Used to set data.

Chapter8
Used to change the
mode.
Used to change the

Fixed part mode.
(4 places)
Section4.3

Section4.3

Chapter7
Section15.1.4
option unit.

Charge lamp
Lit to indicate that the main circuit is charged.
While this lamp is lit, do not reconnect the cables.
Control circuit terminal block (TE2)

Section4.7.2
Used to connect the control circuit power supply and
Section13.1
regenerative option.
Main circuit terminal block (TE1) Section4.7.2

Used to connect the input power supply and servo Section13.1
motor. Section15.1.1

Cooling fan
Protective earth (PE) terminal ( ) Section4.10
1 - 16
(4) MR-J2S-700CP-S084
POINT
The servo amplifier is shown without the front cover. For removal of the
backup.
Battery holder
Section5.5
Display
Operation section
MODE UP DOWN SET Used to perform status display, diagnostic, alarm,
MODE UP DOWN SET
Used to set data.

Chapter8
Used to change the

mode.
Used to change the

mode.
Section4.3

Section4.3

Chapter7
Section15.1.4
option unit.
Charge lamp
Lit to indicate that the main circuit is charged.
While this lamp is lit, do not reconnect the cables.

Used to connect the control circuit power supply. Section13.1

Main circuit terminal block (TE1) Section4.7.2

Used to connect the input power supply, regenerative Section13.1
option and servo motor. Section15.1.1
Cooling fan Protective earth (PE) terminal ( ) Section4.10

Fixed part Ground terminal. Section13.1
(4 places)
1 - 17
1.6.2 Part name of CC-Link unit
CC-Link connector (CN10) Section
Fixed part (2 places) Wire the CC-Link cable. 3.2.2
Station number switches (RSW1, RSW2)

Set the station number of the servo amplifier.
MR-J2S-T01
RSW1: Set the ten place. Section
3.2.3
RSW2: Set the one place.

C
N
Baud rate switch (RSW3)

1
0
Section
R Select the CC-Link communication baud rate. 3.2.4
S
W
1
Occupied station count switch (SW1) Section
2
Set the number of occupied stations. 3.2.5
3
Rating plate Section

1
2 1.4
S
W
Servo amplifier connector

C Connect with the CN3 connector of the MR-J2S-CP-S084 Section
N 4.3.1
3
0 servo amplifier.
Communication alarm display section

Indicates alarms in CC-Link communication.
L.ERR SD Section
C 12.3
N
4
L.RUN RD
0
S.ERR WD
Personal computer connector (CN40)

Connect the personal computer. Chapter 7
Charge lamp
Lit when the control circuit is powered on.
Green: Normal
Orange: Watchdog
1 - 18
1.6.3 Removal and reinstallation of the front cover
Before removing or installing the front cover, turn off the power and wait for 15
minutes or more until the charge lamp turns off. Then, confirm that the voltage
WARNING between P and N is safe with a voltage tester and others. Otherwise, an electric
shock may occur. In addition, always confirm from the front of the servo amplifier
whether the charge lamp is off or not.
(1) For MR-J2S-200CP-S084 or more

Removal of the front cover Reinstallation of the front cover
1)
Front cover hook

2) (2 places)
2)
Front cover
1)
Front cover socket

(2 places)
1) Hold down the removing knob. 1) Insert the front cover hooks into the front cover sockets of
the servo amplifier.
2) Pull the front cover toward you. 2) Press the front cover against the servo amplifier until the
removing knob clicks.
(2) For MR-J2S-500CP-S084

1)
Front cover hook

(2 places)
2)
2)
1)
Front cover
Front cover socket
(2 places)
1) Hold down the removing knob. 1) Insert the front cover hooks into the front cover sockets of
1 - 19
(3) For MR-J2S-700CP-S084

Front cover
hook
(2 places)
B) A)
2)
2)
1) A)
1)
Front cover socket

(2 places)
1) Push the removing knob A) or B), and put you 1) Insert the two front cover hooks at the bottom into the
finger into the front hole of the front cover. sockets of the servo amplifier.
1 - 20
1.7 Servo system with auxiliary equipment
To prevent an electric shock, always connect the protective earth (PE) terminal
WARNING (terminal marked ) of the servo amplifier to the protective earth (PE) of the
control box.

(a) For 3-phase 200V to 230VAC or 1-phase 230VAC
(Note 2)
Options and auxiliary equipment Reference Options and auxiliary equipment Reference
Power supply
No-fuse breaker Section 15.2.2 Regenerative option Section 15.1.1
Magnetic contactor Section 15.2.2 Cables Section 15.2.1
MR Configurator Power factor improving reactor Section 15.2.3
Chapter 7
(Servo configuration software)
Servo amplifier CC-Link unit
No-fuse breaker MR-J2S-T01
(NFB) or fuse MITSUBISHI
CC-Link
CN10
Command device
To CN1A
Magnetic Junction
contactor terminal block
(MC) To CN1B
Power To CN3
factor
improving CHARGE
To CN30
reactor
(FR-BAL) MR Configurator
To CN2 Personal
(Servo configuration
computer
L1 software)
L2 To CN40 MRZJW3-
U V W
SETUP161E
L3
Protective earth (PE) terminal

(Note 1)
Encoder cable
(Note 1)
Power supply lead
Control circuit terminal block D
L21
L11
P
Regenerative
option
C Servo motor
Note 1. The HC-SFS, HC-RFS, HC-UFS 2000r/min series have cannon connectors.
2. A 1-phase 230VAC power supply may be used with the servo amplifier of MR-J2S-70CP-S084 or less. For 1-phase
230 VAC, connect the power supply to L1 and L2 terminals and leave L3 open. Refer to section 1.2 for the power supply
specification.
1 - 21
(b) For 1-phase 100V to 120VAC

(Note 2) Options and auxiliary equipment Reference Options and auxiliary equipment Reference
Power supply
Chapter 7
Servo amplifier CC-Link unit
No-fuse breaker MR-J2S-T01
(NFB) or fuse
MITSUBISHI
CC-Link
CN10
Command device
To CN1A
Magnetic Junction
contactor To CN1B terminal block
(MC)
Power To CN3
factor
improving CHARGE
To CN30
reactor
(FR-BAL)
To CN2 Personal
computer
L1
L2 To CN40 MRZJW3-
U V W
SETUP161E
Protective earth (PE) terminal (Note 1)

Encoder cable
(Note 1)
Power supply lead
Control circuit terminal block D
L21
L11
P
Regenerative
option
C Servo motor
Note 1. The HC-SFS, HC-RFS, HC-UFS 2000r/min series have cannon connectors.
2. Refer to section 1.2 for the power supply specification.
1 - 22
(2) MR-J2S-200CP-S084 MR-J2S-350CP-S084
POINT
The configuration of the MR-J2S-T01 CC-Link unit is the same as in (1) in
this section.
(Note) Options and auxiliary equipment Reference Options and auxiliary equipment Reference
Power supply
Chapter 7
No-fuse
breaker
(NFB) or
fuse Servo amplifier
Command device
To CN1A
Magnetic
contactor Junction terminal
(MC) block
To CN1B
Power
factor
improving To CN2 To CN3
reactor Personal
L11 computer
(FR-BAL)
L21
L1
U V W P C
L2
L3 Regenerative option
Note. Refer to section 1.2 for the power supply specification.
1 - 23
(3) MR-J2S-500CP-S084
POINT
this section.
(Note 2)
Power supply
Options and auxiliary equipment Reference Options and auxiliary equipment Reference
No-fuse Magnetic contactor Section 15.2.2 Cables Section 15.2.1
breaker
(NFB) or MR Configurator Power factor improving reactor Section 15.2.3
Chapter 7
fuse (Servo configuration software)
Magnetic
contactor
(MC)
Power
factor Servo amplifier
improving Command device
reactor
(FR-BAL) To CN1A
L1 Junction terminal
L2 block
L3 To CN1B
(Note 1) C P U
Regenerative option
V To CN3
W MR Configurator
Personal software)
To CN2 computer MRZJW3-
L11 SETUP161E
L21
Note 1. When using the regenerative option, remove the lead wires of the built-in regenerative resistor.
1 - 24
(4) MR-J2S-700CP-S084
POINT
this section.
(Note 2) Options and auxiliary equipment Reference Options and auxiliary equipment Reference
Power supply
Chapter 7
No-fuse
breaker
(NFB) or
fuse Command device
Servo amplifier
L11
To CN1A
L21
Junction terminal
Magnetic block
contactor
(MC) To CN1B
Power
To CN3 MR Configurator
factor
improving
Personal software)
reactor
computer MRZJW3-
(FR-BAL) To CN2 SETUP161E
L3 U
L2 V
L1 W
C P
(Note 1) Regenerative option
Note 1. When using the regenerative option, remove the lead wires of the built-in regenerative resistor.
1 - 25
1.8 Flowchart of Operation Method
Using the CC-Link communication functions, this servo enables a wide variety of operation methods. The
operation method changes depending on the input signal, parameter and point table setting.
The flow of the operation method that changes depending on the signal and parameter setting status is
shown in the following chart for your reference.
Remote input-based point

1 station
occupied table No. setting auxiliary
function valid
MR-J2S-T01 occupied
station count setting
switch SW1
OFF OFF
MR-J2S-CP-S084
+
MR-J2S-T01 OFF ON
(Refer to section 3.2.5) Remote input position/speed

specifying system selection
(RY(n+2)A)
OFF
2 stations
occupied ON Remote register-based
point table No. setting
auxiliary function invalid
Parameter No.41
0
Remote register-based
1 position data setting/point
table No. (speed) setting
2 auxiliary function invalid
Remote register-based
position data/speed data
setting auxiliary function
invalid
1 - 26
Reference Main description

Positioning operation is Section 3.8.2 Positioning is started by
Point table making the start signal
executed once with Section
auxiliary function position data handled valid after selection of
5.2.2 (1)
0 as absolute value. the point table with the
Continuous positioning Section 3.8.2 remote input. Using the
operation is executed with Section auxiliary function,
1 position data handled as automatic continuous
Absolute value 5.2.2 (4)(b)1)
absolute values. operation can be
command
specifying system 2 Positioning operation is Section 3.8.2 performed with
executed once with Section multiple point tables.
Parameter No.0 position data handled 5.2.2 (2)
3 as incremental value.
0
Continuous positioning Section 3.8.2
operation is executed with Section
1 position data handled as 5.2.2 (4)(b)1)
Point table incremental values.
auxiliary function
Positioning operation is Section 3.8.2
0 executed once in Section
Incremental value incremental value 5.2.2 (1)
command command system.
specifying system 1
Continuous positioning Section 3.8.2
operation is executed Section
in incremental value 5.2.2 (4)(b)2)
Remote input absolute command system.
value/incremental value Positioning is started by
selection (RY(n+2)B) Positioning operation is making the start signal
executed once with
OFF position data handled valid after selection of
Parameter No.0 Absolute value as absolute value. the point table with the
command Section remote register. The
0 specifying system ON Positioning operation is 3.6.3 (1)
executed once with auxiliary function
position data handled cannot be used.
Section
1 as incremental value. 3.7.6 (3)
Incremental value Positioning operation is
command executed once in
specifying system incremental value
Remote input absolute command system.
value/incremental value Set the position data
selection (RY(n+2)B) Positioning operation is
executed once with directly with the remote
OFF position data handled register, and use the
Parameter No.0 Absolute value as absolute value. settings of the point
command table selected with the
specifying system ON Positioning operation is
0 executed once with Section remote register as the
position data handled 3.6.3 (2) servo motor speed and
1 as incremental value. acceleration/deceleratio
Positioning operation is n time constants.
Incremental value
command executed once in Positioning is started by
specifying system incremental value making the start signal
Remote input absolute command system. valid. The auxiliary
value/incremental value Set the position data
selection (RY(n+2)B) Positioning operation is Section 3.6.3(3)
executed once with Section 3.8.4
and servo motor speed
OFF position data handled Section 5.2.3(1) directly with the remote
Parameter No.0 Absolute value as absolute value. register.
command Positioning operation is Section Use the settings of the
0 specifying system ON
executed once with 3.6.3 (3) point table No. 1 as the
position data handled Section acceleration/deceleratio
as incremental value. 5.2.3 (2) n time constants.
1
Incremental value Positioning operation is Positioning is started by
command executed once in Section 3.6.3(3) making the start signal
specifying system incremental value Section 3.7.6(2)
valid. The auxiliary
command system. Section 5.2.3(3)
function cannot be used.
1 - 27
MEMO
1 - 28
2. INSTALLATION
2. INSTALLATION
Stacking in excess of the limited number of products is not allowed.

Install the equipment on incombustible material. Installing them directly or close to
combustibles will lead to a fire.
Install the equipment in a load-bearing place in accordance with this Instruction
Manual.
Do not get on or put heavy load on the equipment to prevent injury.
Use the equipment within the specified environmental condition range. (For the
environmental conditions, refer to section 2.1.)
Provide an adequate protection to prevent screws, metallic detritus and other
conductive matter or oil and other combustible matter from entering the servo
CAUTION amplifier.
Do not block the intake/exhaust ports of the servo amplifier. Otherwise, a fault may
occur.
Do not subject the servo amplifier to drop impact or shock loads as they are
precision equipment.
Do not install or operate a faulty servo amplifier.
When the product has been stored for an extended period of time, consult
Mitsubishi.
When treating the servo amplifier, be careful about the edged parts such as the
corners of the servo amplifier.
2.1 Environmental conditions
Environment Conditions
In [ ] 0 to 55 (non-freezing)
Ambient operation [ ] 32 to 131 (non-freezing)
temperature [ ] 20 to 65 (non-freezing)
In storage
Ambient In operation
90%RH or less (non-condensing)
humidity In storage
Indoors (no direct sunlight)
Ambience
Free from corrosive gas, flammable gas, oil mist, dust and dirt
Altitude Max. 1000m (3280 ft) above sea level
[m/s ] 5.9 [m/s2] or less
2
Vibration
[ft/s2] 19.4 [ft/s2] or less
2- 1
2. INSTALLATION
2.2 Installation direction and clearances
Do not hold the front cover to transport the controller. The controller may drop.
The equipment must be installed in the specified direction. Otherwise, a fault may
CAUTION occur.
Leave specified clearances between the servo amplifier and control box inside
walls or other equipment.
(1) Installation of one servo amplifier

Control box Control box
40mm
(1.6 in.)
or more
Servo amplifier Wiring clearance
70mm
(2.8 in.) Up
10mm 10mm
(0.4 in.) (0.4 in.)
or more or more
Down
40mm
(1.6 in.)
or more
2- 2
2. INSTALLATION
(2) Installation of two or more servo amplifiers

Leave a large clearance between the top of the servo amplifier and the internal surface of the control
box, and install a cooling fan to prevent the internal temperature of the control box from exceeding the
environmental conditions.
Control box
10mm
100mm (0.4 in.)
(4.0 in.) or more
or more
30mm 30mm
(1.2 in.) (1.2 in.)
or more or more
40mm
(1.6 in.)
or more
(3) Others
When using heat generating equipment such as the regenerative option, install them with full
consideration of heat generation so that the servo amplifier is not affected.
Install the servo amplifier on a perpendicular wall in the correct vertical direction.
2.3 Keep out foreign materials
(1) When installing the unit in a control box, prevent drill chips and wire fragments from entering the
servo amplifier.
(2) Prevent oil, water, metallic dust, etc. from entering the servo amplifier through openings in the control
box or a cooling fan installed on the ceiling.
(3) When installing the control box in a place where there are much toxic gas, dirt and dust, conduct an
air purge (force clean air into the control box from outside to make the internal pressure higher than
the external pressure) to prevent such materials from entering the control box.
2- 3
2. INSTALLATION
2.4 Cable stress
(1) The way of clamping the cable must be fully examined so that flexing stress and cable's own weight
stress are not applied to the cable connection.
(2) For use in any application where the servo motor moves, fix the cables (encoder, power supply, brake)
supplied with the servo motor, and flex the optional encoder cable or the power supply and brake
wiring cables. Use the optional encoder cable within the flexing life range. Use the power supply and
brake wiring cables within the flexing life of the cables.
(3) Avoid any probability that the cable sheath might be cut by sharp chips, rubbed by a machine corner
or stamped by workers or vehicles.
(4) The flexing lives of the cables are shown below. In actuality, provide a little allowance for these values.
For installation on a machine where the servo motor will move, the flexing radius should be made as
large as possible. Refer to section 14.4 for the flexing life.
2- 4
3. CC-Link COMMUNICATION FUNCTIONS
3.1 Communication specifications
POINT
This servo is equivalent to a remote device station.
For details of the programmable controller side specifications, refer to the CC-Link system master unit
manual.
Item MR-J2S-T01 specifications

Power supply 5VDC supplied from servo amplifier
Applicable CC-Link version Ver.1.10
Applicable servo amplifier MR-J2S- CP -S084
Communication speed 10M/5M/2.5M/625k/156kbps
Communication system Broadcast polling system
Synchronization system Frame synchronization system
Encoding system MRZI
CC-Link
Transmission path format Bus format (conforming to EIA RS485)

Error control system CRC (X16+X12+X5+1)
Connection cable CC-Link Ver.1.10-compliant cable (Shielded 3-core twisted pair cable)
Transmission format Conforming to HDLC
Remote station number 1 to 64
(Note) Communication speed 156Kbps 625Kbps 2.5Mbps 5Mbps 10Mbps
Cable Maximum overall cable length 1200m 900m 400m 160m 100m
length Inter-station cable length 0.2m or more
Max. 42 (when 1 station is occupied by 1 servo amplifier), (max. 32 when
Number of servo amplifiers connected 2 stations are occupied by 1 servo amplifier), when there are only remote
device stations. Can be used with other equipment.
Note. If the system comprises of both CC-Link Ver.1.00- and Ver.1.10-compliant cables, Ver.1.00 specifications are applied to the
overall cable length and the cable length between stations. For more information, refer to the CC-Link system master/local unit
user's manual.
3- 1
3.2 System configuration
3.2.1 Configuration example
(1) Programmable controller side

Fit “Type AJ61BT11”, “Type A1SJ61BT”, “Type AJ61QBT11” or “Type A1SJ61QBT” “Control &
Communication Link system master/local module” to the main or extension base unit which is loaded
with the programmable controller CPU used as the master station.
(2) Wiring
Connect the programmable controller CC-Link unit master station and MR-J2S-T01 CC-Link option
unit by a CC-Link Ver.1.10-compliant cable.
CC-Link unit
CC-Link Ver.1.10-compliant cable
(3) For the CPU having the automatic refresh function (Example: QnA series CPU)
Transfer of data to/from the corresponding devices is performed from a sequence ladder and the
devices are automatically refreshed by the refresh buffer of the master station at the END instruction
to make communications with the remote devices.
(4) For the CPU having no automatic refresh function (Example: AnA series CPU)
Transfer of data to/from the refresh buffer of the master station is performed directly from a sequence
ladder to make communications with the remote devices.
3- 2
3.2.2 Wiring method
(1) Communication connector

The pin layout of the communication connector CN10 on the MR-J2S-T01 option unit is shown below.
Signal
Pin No. name
1 1 DA
2 2 DB
3 3 DG
4 4 SLD
5 5 FG
(2) Connection example

The servo amplifier and programmable controller CC-Link master unit are wired as shown below.
Refer to section 15.2.1 (3) for the CC-Link Ver.1.10-compliant cable used for connection.
CC-Link master unit MR-J2S-T01
CN10
DA DA
DB DB
DG DG
SLD SLD
FG
(3) Example of connecting multiple servo units

As the remote I/O stations of CC-Link, servo amplifiers share the link system and can be
controlled/monitored using programmable controller user programs.
Termination register CC-Link master unit
(Note 1) Termination
MR-J2S-T01 option unit register MR-J2S-T01 option unit
DA
CC-Link connector (CN10) CC-Link connector (CN10)
DB
1 DA 1 DA
DG 2 DB 2 DB
3 DG 3 DG
SLD
4 SLD 4 SLD
FG 5 FG 5 FG
Max. number of axes: 42 stations

(When 1 station is occupied)
(Note 2) CC-Link Ver.1.10-compliant cable
Note 1. Use the termination resistor supplied with the programmable controller. The resistance of the termination resistor depends on
the cable used. For details, refer to the open field network CC-Link catalog (L(NA)74108143).
2. Refer to (4) in this section.
3- 3
(4) How to wire the CC-Link terminal block (TE5)

(a) Strip the sheath of the cable and separate the internal wires and braided shield.
(b) Strip the sheaths of the braided shield and internal wires and twist the cores.
Braided shield
Approx. 10mm (0.394in.)

3-core twisted pair cable
(c) Match and twist the wires and braided shield of the cable connected to the preceding axis or
programmable controller and the corresponding wires and braided shield of the cable connected to
the subsequent axis.
(d) For the last axis, work the termination resistor supplied to the CC-Link master unit as shown
below.
Termination register
(10mm (0.394in.)) (10mm (0.394in.))
Remove sheath Remove sheath Fold lead wire
Cut Cut
(e) Insert the core of the cable into the opening and tighten it with a flat-blade screwdriver so that it
will not come off. (Tightening torque: 0.5 to 0.6N m) When inserting the wire into the opening,
make sure that the terminal screw is fully loose.
CC-Link terminal block
Opening
Loosen Tighten
Wire
To the next
station
Flat blade screwdriver

To the preceding station or
Tip thickness 0.4 to 0.6mm (0.016 to 0.024in.)
programmable controller
Full wide 2.5 to 3.5mm (0.098 to 0.138in.)
POINT
Do not solder the cores as it may cause a contact fault.
Use of a flat-blade torque screwdriver is recommended to manage the screw tightening torque. The
following table indicates the recommended products of the torque screwdriver for tightening torque
management and the flat-blade bit for torque screwdriver. When managing torque with a Phillips bit,
please consult us.
Product Model Manufacturer/Representative
Torque screwdriver N6L TDK Nakamura Seisakusho
Bit for torque screwdriver B-30, flat-blade, H3.5 X 73L Shiro Sangyo
3- 4
3.2.3 Station number setting
(1) How to number the stations

Set the servo station numbers before powering on the servo amplifiers. Note the following points when
setting the station numbers.
(a) Station numbers may be set within the range 1 to 64.
(b) One servo amplifier occupies 1 or 2 stations. (One station of programmable controller remote device
station)
(c) Max. number of connected units: 42

Note that the following conditions must be satisfied.
{(1 a) (2 B) (3 d) (4 d)} 64
a: Number of 1-station occupying units
b: Number of 2-station occupying units
c: Number of 3-station occupying units (not available for MR-J2S-CP-S084)
d: Number of 4-station occupying units (not available for MR-J2S-CP-S084)
{(16 A) (54 B) (88 C)} 2304
A: Number of remote I/O stations 64
B: Number of remote device stations 42
C: Number of local stations 26
(d) When the number of units connected is 4, station numbers can be set as shown below.
Servo amplifier No.1 Servo amplifier No.2 Servo amplifier No.3
Programmable controller (When 2 stations are (When 2 stations are (When 2 stations are
CC-Link remote I/O station occupied) occupied) occupied)
master unit (1 station occupied) Remote device station Remote device station Remote device station
Station No.1 Station No.2 Station No.4 Station No.6
Number of connected units is 4.
(2) Station number setting method

Set the station number with the station number switches (RSW1, RSW2) on the option unit MR-J2S-
T01 front. The station number that may be set is any of 1 to 64 in decimal. In the initial status, the
station number is set to station 1.
RSW1
2 3
1
Set the tens. (initial value: 0)

0
5
6
9
8 7
RSW2
2 3
1
Set the units. (initial value: 1)

0
5
6
9
8 7
3- 5
3.2.4 Communication baud rate setting
Set the transfer baud rate of CC-Link with the transfer baud rate switch (RSW1) on the option unit MR-
J2S-T01 front. The initial value is set to 156kbps.
The overall distance of the system changes with the transfer speed setting. For details, refer to the CC-
Link system master/local unit user's manual.
RSW3
No. Baud rate
2 3 0 (initial value) 156kbps
1
4
1 625kbps
0
5
2 2.5Mbps
6
9
8 7 3 5Mbps
4 10Mbps
5 to 9 Not used
3.2.5 Occupied station count setting
Set the number of occupied stations with the occupied station count switch (SW1) on the option unit MR-
J2S-T01 front. The usable I/O signals and the number of connectable units change with the set number of
occupied stations. Refer to section 3.2.3. In the initial status, the number of stations occupied is set to 1.
SW1 setting Number of occupied stations
OFF 1
OFF 1 station occupied

OFF
2
(Initial value)
OFF 1
OFF 2 stations occupied

ON
2
3- 6
3.3 Functions
This section explains the transfer of I/O data to/from the servo amplifier in CC-Link, using function
blocks.
(1) Between the master station and servo amplifier in the CC-Link system, link refresh is normally
performed at intervals of 3.5 to 18ms (512 points). The link scan time of link refresh changes with the
communication speed. For details, refer to the CC-Link system master/local unit user's manual.
(2) The I/O refresh and master station sequence program are executed asynchronously. Some
programmable controllers allow link scans to be synchronized with programmable controller scans.
(3) The FROM instruction from the buffer memory of the CC-Link system master/local unit is used to
read data from the servo amplifier, and the TO instruction is used to write data. Some programmable
controllers allow automatic refresh to be set to omit the FROM and TO instructions.
Servo amplifier
Programmable controller CC-Link unit
programmable controller
1) AJ61BT11
Servo amplifier CPU

CPU
CC-Link interface
CC-Link interface
I/O signal 3) CC-Link
Input
Interface with
Ver.1.10-compliant
I/O interface
cable
CPU
2) Buffer memory access

Buffer Output
memory
3.3.2 Functions
The following table lists the functions that may be performed from the programmable controller in the
CC-Link system in the CC-Link operation mode or test operation mode.
Operation mode
Item
CC-Link operation mode Test operation mode
Monitor
Operation
Parameter write
Parameter read
Point table data write
Point table data read
3- 7
3.4 Servo amplifier setting
(1) Servo amplifier side operation modes

The MR-J2S- CP-S084 servo amplifier has the following operation modes.
Operation mode Description

The buttons in the operation section of the servo amplifier are operated to run the servo
Test operation mode
motor.
CC-Link communication functions are used to operate the servo with the programmable
CC-Link operation mode
controller programs.
(2) Operation mode changing

(a) Operation mode changing conditions
Change the operation mode after making sure that.
1) The servo motor is at a stop.
2) The forward rotation start (RYn1) or reverse rotation start (RYn2) is OFF.
(b) Operation mode changing method

When changing from test operation to CC-Link operation, deselect test operation by switching
power OFF/ON.
Change with parameter unit
A
CC-Link
Test operation mode
operation mode
B
Symbol Changing Description

Select the test operation mode with the button in
A
the operation section of the servo amplifier.
Test operation mode
Test operation mode
Deselect test operation mode by switching power
B
OFF/ON.
3- 8
3.5 I/O signals transferred to/from the programmable controller CPU
3.5.1 I/O signals
The input signals may be used as either the CC-Link or CN1A CN1B external input signals. Make
selection in parameter No. 116 117 118. The output signals can be used as both the CC-Link CN1A
CN1B external input signals.
POINT
In the factory-shipped status, the forward rotation stroke end (RYn4),
reverse rotation stroke end (RYn5) and proximity dog (RYn3) are valid as
the CN1A CN1B external input signals.
(1) When 1 station is occupied

RYn/RXn: 32 points each, RWrn/RWwn: 4 points each
Programmable controller Servo amplifier (RYn) Servo amplifier Programmable controller (RXn)
(Note) Signal External (Note) Signal External
Signal name Signal name
Device No. abbreviation input Device No. abbreviation output
RYn0 Servo-on SON RXn0 Ready RD CN1B-19

RYn1 Forward rotation start ST1 RXn1 In position INP
RYn2 Reverse rotation start ST2 RXn2 Rough match CPO CN1B-4
RYn3 Proximity dog DOG RXn3 Home position return completion ZP CN1A-18
RYn4 Forward rotation stroke end LSP CN1B-16 RXn4 Limiting torque TLC
RYn5 Reverse rotation stroke end LSN CN1B-17 RXn5 Reserved
RYn6 Automatic/manual selection MD0 RXn6 Electromagnetic brake interlock MBR
RYn7 Temporary stop/Restart STP RXn7 Temporary stop PUS
RYn8 Monitor output execution demand MOR RXn8 Monitoring MOF
Instruction code execution Instruction code execution
RYn9 COR RXn9 COF
demand completion
RYnA Point table No. selection 1 DI0 RXnA Warning WNG
RYnB Point table No. selection 2 DI1 RXnB Battery warning BWNG
RYnC Point table No. selection 3 DI2 RXnC Movement finish MEND CN1B-6
RYnD Point table No. selection 4 DI3 RXnD Reserved
RYnE Point table No. selection 5 DI4 RXnE Position range output POT
RYnF Reserved RXnF Reserved
RY(n+1)0 RX(n+1)1
to Reserved to Reserved
RY(n+1)9 RX(n+1)9
RY(n+1)A Reset RES RX(n+1)A Trouble ALM CN1B-18
Remote station communication
RX(n+1)B CRD
RY(n+1)B ready
to Reserved RX(n+1)C
RY(n+1)F to Reserved
RX(n+1)F
Programmable controller Servo amplifier (RWwn) Servo amplifier Programmable controller (RWrn)
Address No. Signal name Address No. Signal name
RWwn Monitor 1 RWrn Monitor 1 data
RWwn+1 Monitor 2 RWrn+1 Monitor 2 data
RWwn+2 Instruction code RWrn+2 Answer code
RWwn+3 Writing data RWrn+3 Reading data
Note. "n" depends on the station number setting.
3- 9
(2) When 2 stations are occupied

RXn/RYn: 64 points each, RWrn/RWwn: 8 points each
Programmable controller Servo amplifier (RYn) Servo amplifier Programmable controller (RXn)
(Note 1) Signal External (Note 1) Signal External
Device No. abbreviation input Device No. abbreviation output
Yn0 Servo-on SON RXn0 Ready RD CN1B-19

RYn1 Forward rotation start ST1 RXn1 In position INP
RYn2 Reverse rotation start ST2 RXn2 Rough match CPO CN1B-4
RYn3 Proximity dog DOG RXn3 Home position return completion ZP CN1A-18
RYn4 Forward rotation stroke end LSP CN1B-16 RXn4 Limiting torque TLC
RYn5 Reverse rotation stroke end LSN CN1B-17 RXn5 Reserved
RYn6 Automatic/manual selection MD0 RXn6 Electromagnetic brake interlock MBR
RYn7 Temporary stop/Restart STP RXn7 Temporary stop PUS
RYn8 Monitor output execution demand MOR RXn8 Monitoring MOF
Instruction code execution Instruction code execution
RYn9 COR RXn9 COF
demand completion
RYnA Point table No. selection 1 DI0 RXnA Warning WNG
RYnB Point table No. selection 2 DI1 RXnB Battery warning BWNG
RYnC Point table No. selection 3 DI2 RXnC Movement finish MEND CN1B-6
RYnD Point table No. selection 4 DI3 RXnD Reserved
RYnE Point table No. selection 5 DI4 RXnE Position range output POT
RYnF RXnF
RY(n+1)F RX(n+1)F
Position instruction execution Position instruction execution
RY(n+2)0 RX(n+2)0
demand (Note 2) completion
Speed instruction execution Speed instruction execution
RY(n+2)1 RX(n+2)1
demand (Note 2) completion
RY(n+2)2
to Reserved RX(n+2)2 Point table No. output 1 PT0
RY(n+2)5
RY(n+2)6 Internal torque limit selection TL2 RX(n+2)3 Point table No. output 2 PT1
RY(n+2)7 Proportion control PC RX(n+2)4 Point table No. output 3 PT2
RY(n+2)8 Gain changing CDP RX(n+2)5 Point table No. output 4 PT3
RY(n+2)9 Reserved RX(n+2)6 Point table No. output 5 PT4
RX(n+2)7
Position/speed specifying system
RY(n+2)A to Reserved
selection
RX(n+2)9
RX(n+2)A
Absolute value/incremental value
RY(n+2)B to Reserved
selection
RX(n+2)F
RY(n+2)C RX(n+3)0
RY(n+2)F RX(n+3)9
RY(n+3)0
to Reserved RX(n+3)A Trouble ALM CN1B-18
RY(n+3)9
Remote station communication
RY(n+3)A Reset RES RX(n+3)B CRD
ready
RY(n+3)B RX(n+3)C
RY(n+3)F RX(n+3)F
Note 1. "n" depends on the station number setting.
2. Select the command system using parameter No. 41.
3 - 10
Programmable controller Servo amplifier (RWwn) Servo amplifier Programmable controller (RWrn)
(Note 1) (Note 1)
Address No. Address No.
RWwn (Note 2) Monitor 1 RWrn Monitor 1 data lower 16 bit
RWwn+1 (Note 2) Monitor 2 RWrn+1 Monitor 1 data upper 16 bit
RWwn+2 Instruction code RWrn+2 Answer code
RWwn+3 Writing data RWrn+3 Read the data
(Note 3) Position command data lower 16 bit/Point table
RWwn+4 RWrn+4
No.
RWwn+5 Position command data upper 16 bit RWrn+5 Monitor 2 data lower 16 bit
RWwn+6 (Note 4) Speed command data/Point table No. RWrn+6 Monitor 2 data upper 16 bit
RWwn+7 Reserved RWrn+7 Reserved
Note 1. "n" depends on the station number setting.

2. Specify the code of the lower 16 bit as the monitor code of 32-bit data.
3. When the parameter No. 41 setting is " 0", specify the point table No. in RWwn+4. When the parameter No. 41 setting is
" 1" or " 2", specify the position data in RWwn+4/RWwn+5 and turn ON Position instruction execution demand
(RY(n+2)0).
4. When the parameter No. 41 setting is " 1", specify the point table No. in RWwn+6. When the parameter No. 41 setting is
" 2", specify the speed data in RWwn+6, and turn ON Speed instruction execution demand (RY(n+2)1). When the parameter
No. 41 setting is " 0", the RWwn+6 value is not used.
3 - 11
3.5.2 Detailed explanation of I/O signals
(1) Input signals

The signal whose Device No. field has an oblique line cannot be used in CC-Link.
Device No.
Signal name Description 1 station 2 stations Remarks
occupied occupied
Servo-on Turning RYn0 ON powers on the base circuit, making RYn0 RYn0 (Note 1)
operation ready to start. (Servo on status)
Turning it OFF powers off the base circuit, coasting the
servo motor. (Servo off status)
Forward rotation start 1. In absolute value command system RYn1 RYn1 (Note 1)
Turning RYn1 ON for automatic operation executes
positioning once on the basis of the position data set to the
point table.
Turning RYn1 ON for a home position return immediately
starts a home position return.
Keeping RYn1 ON for JOG operation performs rotation in
the forward rotation direction.
Forward rotation indicates the address increasing
direction.
2. In incremental value command system
positioning once in the forward rotation direction on the
basis of the position data set to the point table.
Turning RYn1 ON for a home position return immediately
starts a home position return.
the forward rotation direction.
Forward rotation indicates the address increasing
direction.
Reverse rotation start Use this device in the incremental value command system. RYn2 RYn2 (Note 1)
positioning once in the reverse rotation direction on the
basis of the position data set to the point table.
the reverse rotation direction.
Reverse rotation indicates the address decreasing
direction.
Reverse rotation start (RYn2) is also used as the start
signal of the high-speed automatic positioning function to
the home position.
Proximity dog In the shipment status, the proximity dog external input RYn3 RYn3 (Note 1)
signal (CN1B-7) is valid. For use in CC-Link, make it
usable in parameter No. 116. When RYn3 is turned OFF,
the proximity dog is detected. The polarity of dog detection
can be changed using parameter No. 8.
Parameter No. 8 Proximity dog (RYn3) detection polarity

0 (initial value) OFF
1 ON
3 - 12
Device No.
occupied occupied
Forward rotation stroke In the factory-shipped status, the forward rotation stroke RYn4 RYn4 (Note 1)
end end is valid as the external input signal (CN1B-16) and the (Note 2)
Reverse rotation stroke end reverse rotation stroke end is valid as the external input RYn5 RYn5
signal (CN1B-17).
When starting operation, short CN1B-16 - SG and CN1B-
17 - SG. Opening them causes a sudden stop, resulting in
servo lock.
For use in CC-Link, make it usable in parameter No. 116.
When starting operation, turn RYn4/RYn5 to ON. Turning
it to OFF causes a sudden stop, resulting in servo lock. A
stopping method can be changed in parameter No.22.
When not using the forward/reverse rotation stroke end,
set “Automatic ON in parameter No. 84.
(Note) Input signal Operation

RYn4 RYn5 CCW direction CW direction
1 1
0 1
1 0
0 0
Note. 0: OFF 1: ON
Automatic/manual Turning RYn6 ON selects the automatic operation mode, RYn6 RYn6 (Note 1)
selection and turning it OFF selects the manual operation mode.
Temporary stop/Restart Turning RYn7 ON during automatic operation makes a RYn7 RYn7
temporary stop.
Turning RYn7 ON again makes a restart.
Forward rotation start (RYn1) or Reverse rotation start
(RYn2) is ignored if it is turned ON during a temporary
stop.
When the automatic operation mode is changed to the
manual operation mode during a temporary stop, the
movement remaining distance is erased.
During a home position return or during JOG operation,
Temporary stop/Restart input is ignored.
3 - 13
Device No.
occupied occupied
Monitor output execution When RYn8 is turned ON, the following data and signals RYn8 RYn8
demand are set. At the same time, RXC turns ON. While RXn8 is
ON, the monitor values are kept updated.
1) When 1 station is occupied
Remote register RWrn: Data demanded by Monitor 1
(RWwn)
Remote register RWrn+1: Data demanded by Monitor 2
(RWwn+1)
Remote register RWrn+2: Answer code indicating
normal or error
2) When 2 stations are occupied
Remote register RWrn: Lower 16 bits of data demanded
by Monitor 1 (RWwn)
Remote register RWrn+1: Upper 16 bits of data
demanded by Monitor 1 (RWwn)
Remote register RWrn+5: Lower 16 bits of data
demanded by Monitor 2 (RWwn+2)
Remote register RWrn+6: Upper 16 bits of data
demanded by Monitor 2 (RWwn+2)
Remote register RWrn+2: Answer code indicating
normal or error
Instruction code execution Turning RYn9 ON executes the processing corresponding RYn9 RYn9
demand to the instruction code set to remote register RWwn+2.
After completion of instruction code execution, the answer
code indicating normal or error is set to RWrn+2. At the
same time, RXn9 turns ON.
3 - 14
Device No.
occupied occupied
Point table No. selection 1 The point table Nos. combined by RYnA, RYnB, RYnC, RYnA RYnA (Note 1)
RYnD and RYnE are indicated in the following table. (Note 2)
Point table No. selection 2 RYnB RYnB
(Note) Input signals
Point table No. selection 3 Point table No. RYnC RYnC
RYnA RYnB RYnC RYnD RYnE
Point table No. selection 4 0 (for manual home RYnD RYnD
position return) 0 0 0 0 0
Point table No. selection 5 1 1 0 0 0 0
RYnE RYnE
2 0 1 0 0 0
3 1 1 0 0 0
4 0 0 1 0 0
5 1 0 1 0 0
6 0 1 1 0 0
7 1 1 1 0 0
8 0 0 0 1 0
9 1 0 0 1 0
10 0 1 0 1 0
11 1 1 0 1 0
12 0 0 1 1 0
13 1 0 1 1 0
14 0 1 1 1 0
15 1 1 1 1 0
16 0 0 0 0 1
17 1 0 0 0 1
18 0 1 0 0 1
19 1 1 0 0 1
20 0 0 1 0 1
21 1 0 1 0 1
22 0 1 1 0 1
23 1 1 1 0 1
24 0 0 0 1 1
25 1 0 0 1 1
26 0 1 0 1 1
27 1 1 0 1 1
28 0 0 1 1 1
29 1 0 1 1 1
30 0 1 1 1 1
31 1 1 1 1 1
Note. 0: OFF 1: ON
Position instruction When RY(n+2)0 is turned ON, the point table No. or RY(n+2)0
demand position command data set to remote register
RWwn+4/RWwn+5 is set.
When it is set to the servo amplifier, the answer code
indicating normal or error is set to RWrn+2. At the same
time, RX(n+2)0 turns ON.
Refer to section 3.6.3 for details.
Speed instruction demand When RY(n+2)1 is turned ON, the point table No. or speed RY(n+2)1
command data set to remote register RWwn+6 is set.
When it is set to the servo amplifier, the answer code
indicating normal or error is set to RWrn+2. At the same
time, RX(n+2)1 turns ON.
Refer to section 3.6.3 for details.
3 - 15
Device No.
occupied occupied
Internal torque limit Turning RY(n+2)6 OFF makes the torque limit value of RY(n+2)6 (Note 1)
selection parameter No. 28 (internal torque limit 1) valid, and
turning it ON makes that of parameter No. 29 (internal
torque limit 2) valid. (Refer to section 4.4.3)
Proportion control When RY(n+2)7 is turned ON, the speed amplifier is RY(n+2)7 (Note 1)
switched from the proportional integral type to the (Note 2)
proportional type.
If the servo motor at a stop is rotated even one pulse by an
external factor, it develops torque in an attempt to
compensate for a position shift. When the shaft is locked
mechanically after Movement finish (RXnC) is turned OFF,
for example, turning Proportion control (RY(n+2)7) ON as
soon as Movement finish (RXnC) turns OFF allows control
of unnecessary torque developed in an attempt to
compensate for a position shift.
When the shaft is to be locked for an extended period of
time, turn Internal torque limit selection (RY(n+2)6) ON
simultaneously with Proportion control (RY(n+2)7) to make
the torque not more than the rated torque using Internal
torque limit 2 (parameter No. 29).
Gain changing When RY(n+2)8 is turned ON, the load inertia moment RY(n+2)8 (Note 1)
ratio changes to parameter No. 64 (ratio of load inertia
moment to servo motor inertia moment 2), and the
corresponding gain values change to the values obtained by
multiplying parameter No. 65 to 67.
Position/speed specifying Select how to give a position command/speed command. RY(n+2)A
system selection (Refer to section 3.6.3.)
OFF: Remote input-based position/speed specifying system
Specifying the point table No. with Point table No.
selection (RYnA to RYnE) gives a position
command/speed command.
ON : Remote register-based position/speed specifying
system
Setting the instruction code to the remote register
(RWwn+4 to RWwn+6) gives a position
command/speed command.
Using parameter No. 41, select the instruction code
to be set.
Absolute value/incremental RY(n+2)B is made valid when the remote register-based RY(n+2)B
value selection position/speed specifying system is selected with
Position/speed specifying system selection (RY(n+2)A) and
the absolute value command system is selected in
parameter No. 0. Turn RY(n+2)B OFF or ON to select
whether the set position data is in the absolute value
command system or incremental value command system.
OFF: Position data is handled as an absolute value.
ON : Position data is handled as an incremental value.
3 - 16
Device No.
occupied occupied
Reset Keeping RY(n+1)A or RY(n+3)A ON for 50ms or longer RY(n+1)A RY(n+3)A (Note 1)
allows an alarm to be deactivated.
Some alarms cannot be deactivated by Reset RY(n+1)A or
RY(n+3)A. (Refer to section 12.4.1.)
If RY(n+1)A or RY(n+3)A is turned ON with no alarm
occurring, the base circuit will not be shut off. When
" 1 " is set in parameter No. 55 (function selection 6),
the base circuit is shut off.
This signal is not designed to make a stop. Do not turn it
ON during operation.
Forced stop This signal is exclusively used as a CN1A/CN1B external
input signal. It cannot be used for CC-Link.
Opening EMG-SG results in a forced stop status, switches
the servo off, and operates the dynamic brake to make a
sudden stop.
Short EMG-SG in the forced stop status to cancel the
forced stop status.
Note 1. Can be used as a CN1A/CN1B external input signal by setting parameter No. 116 to 118, parameter No. 79 to 83.
2. Can be automatically turned ON (kept ON) internally by setting parameter No. 84 to 86.
3 - 17
(2) Output signals

The signal whose Device No. field has an oblique line cannot be used in CC-Link.
Device No.
Signal name Description 1 station 2 stations
occupied occupied
Ready RXn0 turns ON when the servo amplifier is ready to operate after RXn0 RXn0
servo-on.
In position RXn1 turns ON when the droop pulse value is within the preset in- RXn1 RXn1
position range.
The in-position range can be changed using parameter No. 6.
Increasing the in-position range may result in a continuous
conduction status during low-speed rotation.
RXn1 turns ON at servo-on.
Rough match RXn2 turns ON when the command remaining distance becomes RXn2 RXn2
less than the rough match output range set in the parameter.
RXn2 turns ON at servo-on.
Home position return RXn3 turns ON at completion of a home position return. RXn3 RXn3
completion In an absolute position system, RXn3 turns ON when operation is
ready to start, but turns OFF in any of the following cases.
1) Servo-on (RYn0) is turned OFF.
2) Forced stop (EMG) is turned OFF.
3) Reset (RY(n+1)A or RY(n+3)A) is turned ON.
4) Alarm occurs.
5) Forward rotation stroke end (RYn4) or Reverse rotation stroke
end (RYn5) is turned OFF.
6) Home position return has not been made.
7) Home position return has not been made after occurrence of
Absolute position erase (AL.25) or Absolute position counter
warning (AL.E3).
8) Home position return has not been made after electronic gear
change.
9) Home position return has not been made after the absolute
position system was changed from invalid to valid.
10) Forward rotation starting coordinate system ("000_" of
parameter No. 1) has been changed.
11) Software limit is valid.
12) While a home position return is being made.
When any of 1) to 12) has not occurred and a home position return
is already completed at least once, Home position return
completion (RXn3) turns to the same output status as Ready
(RXn0).
Limiting torque RXn4 turns OFF when the torque set as Internal torque limit 1 RXn4 RXn4
(parameter No. 28) or Internal torque limit 2 (parameter No. 29) is
reached at the time of torque generation.
Electromagnetic brake RXn6 turns OFF at servo-off or alarm occurrence. At alarm RXn6 RXn6
interlock occurrence, it turns OFF independently of the base circuit status.
Temporary stop RXn7 turns ON when deceleration is started to make a stop by RXn7 RXn7
Temporary stop/Restart (RYn7). When Temporary stop/Restart
(RYn7) is made valid again to resume operation, RXn7 turns OFF.
Monitoring Refer to Monitor output execution demand. RXn8 RXn8
3 - 18
Device No.
occupied occupied
Instruction code execution Refer to Instruction code execution demand. RXn9 RXn9
completion
Warning RXnA turns ON when a warning occurs. RXnA RXnA
When no warning has occurred, RXnA turns OFF within about 1s
after power-on.
Battery warning RXnB turns ON when Open battery cable warning (AL.92) or RXnB RXnB
Battery warning (AL.9F) occurs. When no battery warning has
occurred, RXnB turns OFF within about 1s after power-on.
Movement finish RXnC turns ON when In position (RXn1) turns ON and the RXnC RXnC
command remaining distance is "0".
RXnC turns ON at servo-on.
Position range RXnE turns ON when the actual current position falls within the RXnE RXnE
range set in the parameter.
It is OFF when a home position return is not yet completed or
while the base circuit is off.
Position instruction Refer to Speed instruction execution demand (RY(n+2)0). RX(n+2)0
execution completion
Speed instruction Refer to Position instruction execution demand (RY(n+2)1). RX(n+2)1
3 - 19
Device No.
occupied occupied
Point table No. output 1 As soon as Movement finish (RXnC) turns ON, the point table No. RX(n+2)2
Point table No. output 2 is output in 5-bit code. RX(n+2)3
Point table No. output 3 Point table (Note 1) Output signal RX(n+2)4
Point table No. output 4 No. RX(n+2)2 RX(n+2)3 RX(n+2)4 RX(n+2)5 RX(n+2)6 RX(n+2)5
Point table No. output 5 0 (Note 2) 0 0 0 0 0 RX(n+2)6
1 1 0 0 0 0
2 0 1 0 0 0
3 1 1 0 0 0
4 0 0 1 0 0
5 1 0 1 0 0
6 0 1 1 0 0
7 1 1 1 0 0
8 0 0 0 1 0
9 1 0 0 1 0
10 0 1 0 1 0
11 1 1 0 1 0
12 0 0 1 1 0
13 1 0 1 1 0
14 0 1 1 1 0
15 1 1 1 1 0
16 0 0 0 0 1
17 1 0 0 0 1
18 0 1 0 0 1
19 1 1 0 0 1
20 0 0 1 0 1
21 1 0 1 0 1
22 0 1 1 0 1
23 1 1 1 0 1
24 0 0 0 1 1
25 1 0 0 1 1
26 0 1 0 1 1
27 1 1 0 1 1
28 0 0 1 1 1
29 1 0 1 1 1
30 0 1 1 1 1
31 1 1 1 1 1
Note1. 0: OFF 1: ON
2. For manual home position return
RX(n+2)2 to RX(n+2)6 turn OFF in any of the following statuses.
Power on
Servo off
During home position return
Home position return completion
In any of the following statuses, RX(n+2)2 to RX(n+2)6 maintain
their pre-change status (ON/OFF).
When operation mode is changed
When Automatic/manual selection (RYn6) is turned from OFF to
ON or from ON to OFF to change the operation mode.
During manual operation
During execution of automatic positioning to home position
3 - 20
Device No.
occupied occupied
Trouble RX(n+1)A or RX(n+3)A turns ON when the protective circuit is RX(n+1)A RX(n+3)A
activated to shut off the base circuit.
When no alarm has occurred, RX(n+1)A or RX(n+3)A turns OFF
within about 1s after power is switched ON.
Remote station This signal turns ON at power-on and turns off at a trouble RX(n+1)B RX(n+3)B
communication ready occurrence or in the reset (RX (n+1) A or RX (n+3) A) ON status.
(3) Remote registers

The signal whose Remote Register field has an oblique line cannot be used.
(a) Input (Programmable controller Servo amplifier)

Remote register
1 station 2 stations Signal name Description Setting range
occupied occupied
RWwn RWwn Monitor 1 Demands the status indication data of the servo Refer to section
amplifier. 3.5.3.
Setting the monitor code of the status indication item
to be monitored to RWwn and turning RYn8 to ON sets
data to RWrn. RXn8 turns on at the same time.
to be monitored to RWwn and turning RYn8 to ON sets
data to RWrn. RXn8 turns on at the same time.
When demanding 32-bit data, specifying the lower 16-
bit code No. and turning RYn8 to ON sets the lower 16-
bit data to RWwn and the upper 16-bit data to RWrn.
data is stored in the RXn8. RXn8 turns on at the same
time.
Refer to section 3.5.3 for the item of the monitor code of
the status indication.
RWwn+1 RWwn+1 Monitor 2 Demands the status indication data of the servo Refer to section
amplifier. 3.5.3.
to be monitored to RWwn+1 and turning RYn8 to ON
sets data to RWrn+1. RXn8 turns on at the same time.
to be monitored to RWwn+1 and turning RYn8 to ON
sets data to RWrn+5. RXn8 turns on at the same time.
When demanding 32-bit data, specifying the lower 16-
bit code No. and turning RYn8 to ON sets the lower 16-
bit data to RWwn+5 and the upper 16-bit data to
RWrn+6. data is stored in the RXn8. RXn8 turns on at
the same time.
Refer to section 3.5.3 for the item of the monitor code of
the status indication.
3 - 21
Remote register
1 station 2 stations Signal name Description Setting range
occupied occupied
RWwn+2 RWwn+2 Instruction code Sets the instruction code used to perform parameter or Refer to section
point table data read, alarm reference or the like. 3.5.4 (1).
Setting the instruction code to RWwn+2 and turning
RYn9 to ON executes the instruction. RXn9 turns to ON
on completion of instruction execution.
Refer to section 3.5.4 for instruction code definitions.
RWwn+3 RWwn+3 Writing data Sets the written data used to perform parameter or point Refer to section
table data write, alarm history clear or the like. 3.5.4 (2).
Setting the written data to RWwn+3 and turning RYn9
to ON writes the data to the servo amplifier. RXn9 turns
to ON on completion of write.
Refer to section 3.5.4 (2) for written data definitions.
RWwn+4 Point table Set the point table No. to be executed in the automatic Point table No.:
No./Position operation mode when 2 stations are occupied. 0 to 31
command data When the point table No. is set to RWwn+4 and Absolute value
lower 16 bit RY(n+2)0 is turned ON, the point table No. is set to the command: Position
servo amplifier. On completion of setting, RX(n+2)0 turns command data:
ON. 999999 to 999999
When the point table is not used, set the position Incremental value
command data. command: Position
When the lower 16 bits are set to RWwn+4 and the upper command data:
16 bits to RWwn+5, and RY(n+2)0 is turned ON, the 0 to 999999
RWwn+5 Position command position command data in the upper and lower 16 bits
data upper 16 bit are written. On complete of write, RX(n+2)0 turns ON.
Use parameter No. 41 to select whether point table No.
setting or position command data setting will be made.
Refer to section 3.6.3 for details of Point table
No./Position command data.
RWwn+6 Point table When the point table is not used, set the point table No. Point table No.:
No./Speed to be executed or the speed command data (servo motor 0 to 31
command data speed [r/min]). Speed command
When the point table No. is set to RWwn+6 and data:
RY(n+2)1 is turned ON, the point table No. or speed 0 to permissible
command data is set to the servo amplifier. On speed
completion of setting, RX(n+2)1 turns ON.
Use parameter No. 41 to select whether point table No.
setting or speed command data setting will be made.
Refer to section 3.6.3 for details of Point table No./Speed
command data.
3 - 22
(b) Output (Servo amplifier programmable controller)

Note that the data set to RWrn and RWrn+1 depends on whether 1 station or 2 stations are
occupied.
If you set inappropriate code No. or data to the remote register input, the error code is set to
Answer code (RWrn+2). Refer to section 3.5.5 for the error code.
When 1 station is occupied

Remote register Signal name Description
RWrn Monitor 1 data The data of the monitor code set to RWwn is set.
RWrn+1 Monitor 2 data The data of the monitor code set to RWwn+1 is set.
“0000” is set when the codes set to RWwn to RWwn+3 are executed
RWrn+2 Answer code
normally.
RWrn+3 Reading data Data corresponding to the read code set to RWwn+2 is set.
When 2 stations are occupied

Remote register Signal name Description
RWrn Monitor 1 data lower 16bit The lower 16 bits of the data of the monitor code set to RWwn are set.
Monitor 1 data upper 16bit The upper 16 bits of the data of the monitor code set to RWwn are set. A
RWrn+1
sign is set if there are no data in the upper 16 bits.
Answer code “0000” is set when the codes set to RWwn to RWwn+6 are executed
RWrn+2
normally.
RWrn+3 Reading data Data corresponding to the read code set to RWwn+2 is set.
RWrn+4
RWrn+5 Monitor 2 data lower 16bit The lower 16 bits of the data of the monitor code set to RWwn+1 are set.
Monitor 2 data upper 16bit The upper 16 bits of the data of the monitor code set to RWwn+1 are set.
RWrn+6
A sign is set if there are no data in the upper 16 bits.
RWrn+7
3 - 23
3.5.3 Monitor codes
To demand 32-bit data when 2 stations are occupied, specify the lower 16-bit code No. Use any of the
instruction codes 0101 to 011C to read the decimal point position (multiplying factor) of the status
indication.
Setting any code No. that is not given in this section will set the error code ( 1 ) to Answer code
(RWrn+2). At this time, “0000” is set to RWrn, RWrn+1, RWrn+5 and RWrn+6.
For monitor data, refer to section 8.2.3.
Answer data
Code No.
(Servo amplifier Programmable controller)
Monitored item
1 station 2 stations
Data length Unit
occupied occupied
0000h 0000h
0001h 0001h Current position lower 16bit 16bit
0002h Current position upper 16bit 16bit
0003h 0003h Command position lower 16bit 16bit 10STM[mm] or
0004h Command position upper 16bit 16bit 10STM[inch]
0005h 0005h Command remaining distance lower 16bit 16bit
0006h Command remaining distance upper 16bit 16bit
0007h 0007h Not monitored 16bit
0008h 0008h Point table 16bit [No.]
0009h
000Ah 000Ah Feedback pulse value lower 16bit 16bit [pulse]
000Bh Feedback pulse value upper 16bit 16bit [pulse]
000Ch
000Dh
000Eh 000Eh Droop pulse value lower 16bit 16bit [pulse]
000Fh Droop pulse value upper 16bit 16bit [pulse]
0010h 0010h Torque limit command voltage 16bit 0.01[V]
0011h 0011h Regenerative load factor 16bit [%]
0012h 0012h Effective load factor 16bit [%]
0013h 0013h Peak load factor 16bit [%]
0014h Instantaneously occurring torque 16bit [%]
0015h 0015h ABS counter 16bit [rev]
0016h 0016h Motor speed lower 16bit 16bit 0.1[rev/min]
0017h Motor speed upper 16bit 16bit 0.1[rev/min]
0018h 0018h Bus voltage 16bit [V]
0019h 0019h ABS position lower 16bit 16bit [pulse]
001Ah ABS position middle 16bit 16bit [pulse]
001Bh 001Bh ABS position upper 16bit 16bit [pulse]
001Ch 001Ch Within one-revolution position lower 16bit 16bit [pulse]
001Dh Within one-revolution position upper 16bit 16bit [pulse]
3 - 24
3.5.4 Instruction codes (RWwn+2 RWwn+3)
Refer to section 3.6.2 for the instruction code timing charts.
(1) Read instruction codes

The word data requested to be read with the instruction code 0000h to 0AFFh is read by Read code
(RWrn+3).
Set the command code No. corresponding to the item to RWrn+2. The codes and answer data are all 4-
digit hexadecimal numbers.
Setting any command code No. that is not given in this section will set the error code ( 1 ) to
Answer code (RWrn+2). At this time, "0000" is set to Reading data (RWrn+3).
Reading data (RWrn+3) contents

Code No. Item/Function
0000h Operation mode 0000: CC-Link operation mode
Reads the current operation mode. 0001: Test operation mode
0002h Travel multiplying factor
Reads the multiplying factor of the
position data in the point table set in
parameter No. 1. Travel multiplying factor
0300: 1000
0200: 100
0100: 10
0000: 1
0010h Current alarm (warning) reading

Reads the alarm No. or warning No. 0 0
occurring currently.
Occurring alarm No./warning No.
0020h Alarm number in alarm history (most

recent alarm) 0 0
0021h Alarm number in alarm history (first
recent alarm) Alarm No. that occurred in past
0022h Alarm number in alarm history (second
recent alarm)
0023h Alarm number in alarm history (third
recent alarm)
0024h Alarm number in alarm history (fourth
recent alarm)
0025h Alarm number in alarm history (fifth
recent alarm)
0030h Alarm occurrence time in alarm history
(most recent alarm)
(first recent alarm) Occurrence time of alarm that occurred in past
(second recent alarm)
(third recent alarm)
(fourth recent alarm)
(fifth recent alarm)
3 - 25

0040h Input signal status 0 bit 0 to bit F indicate the OFF/ON statuses of the corresponding
Reads the statuses (OFF/ON) of the input input signals. Refer to section 3.5.1 for the meanings of the
signals. abbreviations.
bitF bit0
When 2 stations are occupied, DI0, DI1 and DI2 do not function
and therefore they are always “0”.
bit0: SON bit4: LSP bit8: MOR bitC: DI2
bit1: ST1 bit5: LSN bit9: COR bitD: DI3
bit2: ST2 bit6: MD0 bitA: DI0 bitE: DI4
bit3: DOG bit7: STR bitB: DI1 bitF:
bitF bit0
bit0: PSR bit4: bit8: CDP bitC:

bit1: SPR bit5: bit9: bitD:
bit2: bit6: TL1 bitA: CSL bitE:
bit3: bit7: PC bitB: INC bitF:
bitF bit0
bit0: bit4: bit8: bitC:

bit1: bit5: bit9: bitD:
bit2: bit6: bitA: RES bitE:
bit3: bit7: bitB: bitF:
0050h Output signal status 0 bit 0 to bit F indicate the OFF/ON statuses of the corresponding
Reads the statuses (OFF/ON) of the output signals. Refer to section 3.5.1 for the meanings of the
Output signals. abbreviations.
bitF bit0
bit0: RD bit4: TLC bit8: MOF bitC: MEND

bit1: INP bit5: bit9: COF bitD:
bit2: CPO bit6: MBR bitA: WNG bitE: POT
bit3: ZP bit7: PUS bitB: BWNG bitF:
bitF bit0
When 2 stations are occupied, MC0 and MC1 do not function and
therefore they are always “0”.
bit0: PSF bit4: PT2 bit8: bitC:
bit1: SPF bit5: PT3 bit9: bitD:
bit2: PT0 bit6: PT4 bitA: bitE:
bit3: PT1 bit7: bitB: bitF:
3 - 26

bitF bit0
When 2 stations are occupied, MC0 and MC1 do not function and
therefore they are always “0”.
bit0: bit4: bit8: bitC:
bit1: bit5: bit9: bitD:
bit2: bit6: bitA: ALM bitE:
bit3: bit7: bitB: CRD bitF:
0081h Energization time Returns the energization time [h].
Reads the energization time from
shipment.
Energization time
0082h Power ON frequency Returns the number of power-on times.

Reads the number of power-on times from
shipment.
Power ON frequency
00A0h Ratio of load inertia moment Returns the estimated ratio of load inertia moment to servo motor
Reads the estimated ratio of load inertia shaft inertia moment [times].
moment to servo motor shaft inertia
moment.
Ratio of load inertia moment
00B0h Home position within-1-revolution position Return unit [pulses]

lower 16bit (CYC0)
Reads the lower 16 bits of the cycle
counter value of the absolute home
Cycle counter value
position.
00B1h Home position within-1-revolution position Return unit [pulses]
upper 16bit (CYC0)
Reads the upper 16 bits of the cycle
counter value of the absolute home
Cycle counter value
position.
00B2h Home position Multi-revolution data Return unit [rev]
(ABS0)
Multi-revolution counter value of absolute
home position reading
Multi-revolution counter value
00C0h Error parameter No./Point data No.

reading 0
Reads the parameter No./point table No.
in error. Parameter No. or point table
1: Parameter No.
2: Point table No.
3 - 27

0100h Monitor multiplying factor
to Reads the multiplying factor of the data to
011Dh be read with the monitor code.
The instruction codes 0100 to 011D Monitor multiplying factor
correspond to the monitor codes 0000 to 0003: 1000
011D. 0002: 100
0000 applies to the instruction code that 0001: 10
0000: 1
does not correspond to the monitor code.
0200h Parameter No. 0 to 124 data reading The setting of the requested parameter No. is returned.
to Reads the values set in parameter No. 0 to
027Ch 124.
The decimal value converted from the 2
lower digits of the code No. corresponds to
the parameter No.
If the instruction code is set outside the
range set in parameter No. 19, an error
code is returned and the data cannot be
read.
The parameter No. 1 data is headed by
"FF" when it is read.
0300h Data form of parameter No. 0 to 124 The setting of the requested parameter No. is returned.
to Reads the data format of the values set in
037Ch parameter No. 0 to 124. 0
The decimal value converted from the 2
lower digits of the code No. corresponds to Decimal point position
the parameter No. 0: Without decimal point
If the instruction code is set outside the 1: First least significant digit
(without decimal point)
range set in parameter No. 19, an error Data format 2: Second least significant digit
code is returned and the data cannot be 0: Used unchanged 3: Third least significant digit
read. as hexadecimal 4: Fourth least significant digit
1: Must be converted
into decimal
Parameter write type

0: Valid after write
1: Valid when power is switched on again after write
0401h Position data of point table No. 1 to 31 The position data (upper 16 bits or lower 16 bits) set in the
to Reads the point table data of point table requested point table No. is returned.
041Fh No. 1 to 31.
0400 to 041F: Position data in lower 16
0501h bits of point table No. 1 to 31
to 0500 to 051F: Position data in upper 16
051Fh bits of point table No. 1 to 31
Example
Instruction code 0413: Lower 16 bits of
point table No. 19
Instruction code 0513: Upper 16 bits of
point table No. 19
0601h Servo motor speed of point table No. 1 to The servo motor speed set to the requested point table No. is
to 31 returned.
061Fh The decimal value converted from the 2
the point table No.
Servo motor speed
3 - 28

0701h Acceleration time constant of point table The acceleration time constant set to the requested point table
to No. 1 to 31 No. is returned.
the point table No.
0801h Deceleration time constant of point table The deceleration time constant set to the requested point table
to No. 1 to 31 No. is returned.
the point table No.
0901h Dwell of point table No. 1 to 31 The dwell set to the requested point table No. is returned.
to The decimal value converted from the 2
091Fh lower digits of the code No. corresponds to
the point table No.
0A01h Auxiliary function of point table No. 1 to The Auxiliary function set to the requested point table No. is
to 31 returned.
0A1Fh The decimal value converted from the 2
the point table No.
(2) Write instruction codes

Set the data, which was requested to be written with the instruction code 8010h to 911Fh.
Set the instruction code No. corresponding to the item to Instruction code (RWwn+2) and the written
data to Writing data (RWwn+3). The codes and answer data are all 4-digit hexadecimal numbers.
When the instruction code which has not been described in this section is set, the error code ( 1 )
is stored in answer code (RWrn+2).
Writing data (RWwn+3) contents

Code No. Item
(Programmable controller Servo amplifier)
8010h Alarm reset command 1EA5
Deactivates the alarm that occurred.
8101h Feedback pulse value display data is clear 1EA5
Resets the display data of the status indication
“feedback pulse value” to 0.
8200h Data RAM instruction of parameter No. 0 to 124 Convert the decimal values into hexadecimal before
to Writes the values set in parameter No. 0 to 124 to making setting.
827Ch RAM. These values are cleared when power is
switched off.
The decimal value converted from the 2 lower digits of
the code No. corresponds to the parameter No.
An error code is returned if an instruction code
outside the range set in parameter No. 19 or a value
outside the setting range of the corresponding
parameter is written.
3 - 29

Code No. Item
8300h Data EEP-ROM instruction of parameter 0 to 124 Convert the decimal values into hexadecimal before
to Writes the values set in parameter No. 0 to 124 to making setting.
837Ch EEP-ROM. Written to EEP-ROM, these values are held
if power is switched off.
the code No. corresponds to the parameter No.
An error code is returned if an instruction code outside
the range set in parameter No. 19 or a value outside
the setting range of the corresponding parameter is
written.
8401h Position data RAM command of point table Convert the values into hexadecimal before making
to Writes the position data of point table No. 1 to 31 to setting.
841Fh RAM. These values are cleared when power is switched
off.
8501h
to
851Fh Point
A set of the upper and lower bits makes position data. When changing the
data, always set the data of both lower and upper bits in order of lower 16-bit
data and upper 16-bit data.
8400h to 841Fh: Position data in lower 16 bits of point table No. 1 to 31
8500h to 851Fh: Position data in upper 16 bits of point table No. 1 to 31
Example
Instruction code 8413h: Lower 16 bits of point table No. 19
Instruction code 8513h: Upper 16 bits of point table No. 19
8601h Motor speed of point table Convert the values into hexadecimal before making
to Writes the motor speeds of point table No. 1 to 31 to setting.
861Fh RAM. These values are cleared when power is switched
off.
the code No. corresponds to the point table No.
8701h Acceleration time constant data RAM command of Convert the values into hexadecimal before making
to point table setting.
871Fh Writes the acceleration time constants of point table
No. 1 to 31 to RAM. These values are cleared when
power is switched off.
8801h Deceleration time constant data RAM command of Convert the values into hexadecimal before making
881Fh Writes the deceleration time constants of point table
No. 1 to 31 to RAM. These values are cleared when
3 - 30

Code No. Item
8901h Dwell data RAM command of point table Convert the values into hexadecimal before making
to Writes the dwell data of point table No. 0 to 31 to RAM. setting.
891Fh These values are cleared when power is switched off.
8A01h Auxiliary function data RAM command of point table Convert the values into hexadecimal before making
to Writes the auxiliary function data of point table No. 0 setting.
8A1Fh to 31 to RAM. These values are cleared when power is
switched off.
8B01h Position data EEP-ROM command of point table Convert the values into hexadecimal before making
to Writes the position data of point table No. 1 to 8 to setting.
8B1Fh EEP-ROM. Written to EEP-ROM, these values are held
if power is switched off.
8C01h
to Point
8C1Fh
A set of the upper and lower bits makes position data. When changing the
data, always set the data of both lower and upper bits in order of lower 16-bit
data and upper 16-bit data.
8B01h to 8B1Fh: Position data in lower 16 bits of point table No. 1 to 31
8C01h to 8C1Fh: Position data in upper 16 bits of point table No. 1 to 31
Example
Instruction code 8B13h: Lower 16 bits of point table No. 19
Instruction code 8C13h: Upper 16 bits of point table No. 19
8D01h Servo motor speed data EEP-ROM command of point Convert the values into hexadecimal before making
to table setting.
8D1Fh Writes the servo motor speeds of point table No. 1 to 31
to EEP-ROM. Written to EEP-ROM, these values are
held if power is switched off.
8E01h Acceleration time constant data EEP-ROM command of Convert the values into hexadecimal before making
8E1Fh Writes the acceleration time constants of point table
No. 1 to 31 to EEP-ROM. Written to EEP-ROM, these
values are held if power is switched off.
8F01h Deceleration time constant data EEP-ROM command Convert the values into hexadecimal before making
to of point table setting.
8F1Fh Writes the deceleration time constants of point table
No. 1 to 31 to EEP-ROM. Written to EEP-ROM, these
9001h Dwell data EEP-ROM command of point table Convert the values into hexadecimal before making
to Writes the dwell data of point table No. 1 to 31 to EEP- setting.
901Fh ROM. Written to EEP-ROM, these values are held if
3 - 31

Code No. Item
9101h Auxiliary function data EEP-ROM command of point Convert the values into hexadecimal before making
to table setting.
911Fh Writes the auxiliary function data of point table No. 1
to 31 to EEP-ROM. Written to EEP-ROM, these
3.5.5 Answer codes (RWrn+2)
If any of the monitor codes, instruction codes, position command data/point table Nos., speed command
data/point table Nos. set to the remote register is outside the setting range, the corresponding error code
is set to Answer code (RWwn+2). “0000” is set if they are normal.
Error related to Monitor code 1/Monitor code 2
Error related to Instruction code/Writing data
Error related to Position instruction data/Point table No.
Error related to Speed instruction data/Point table No.
Code No. Error Details

0 Normal answer Instruction was completed normally.
Code error The monitor code not in the specifications was set.
1
Read/write of the point table of No. 32 or later was set.
Parameter point table The parameter No. disabled for reference was set.
2
selection error
Write range error An attempt was made to write the parameter or point table data
3
outside the setting range.
3 - 32
3.5.6 Setting the CN1A CN1B external input signals
Using parameter No. 116 to 118, you can assign the input signals as the CN1A CN1B external input
signals. The signals assigned as the CN1A CN1B external input signals cannot be used in CC-Link.
Refer to section 4.3.2 (1)(a) for the pins to which signals can be assigned.
In the initial status, the forward rotation stroke end, reverse rotation stroke end and proximity dog are
preset to be usable as the CN1B external input signals.
Parameter No.116
0
Signal name Initial value
BIN HEX
0
0
0
Servo-on 0
Reset 0

BIN HEX
Forward rotation stroke end 1
Reverse rotation stroke end 1
3
Forward rotation start 0
Reverse rotation start 0
BIN HEX
Automatic/manual selection 0
Proximity dog 1
2
0
0
BIN 0: Used in CC-Link
BIN 1: Used as CN1A and CN1B external input signal
Parameter No.117
0 0
BIN HEX
Internal torque limit selection 0
Proportion control 0
0
Temporary stop/Restart 0
0

BIN HEX
1
1
0
0
Gain changing selection 0
Parameter No.118
0 0
Initial value
Signal name
BIN HEX
Point table No. selection 1 0
Point table No. selection 3 0 0
Initial value
Signal name
BIN HEX
0
0 0
0
3 - 33
3.6 Data communication timing charts
3.6.1 Monitor codes
(1) When 1 station is occupied

Monitor 1
(RWwn)
Monitor 2
(RWwn+1)
Monitor execution ON
demand (RYn8) OFF
Monitoring ON
(RXn8) OFF
Monitor 1 data
(RWrn)
Monitor 2 data
(RWrn+1)
Answer code
(RWrn+2)
Data HOLD
Set the monitor codes (refer to section 3.5.3) to Monitor 1 (RWwn) and Monitor 2 (RWwn+1) and turn
Monitor output execution demand (RYn8) to ON. Turning Monitor execution demand (RYn8) to ON sets
the next data. Data are all hexadecimal numbers. At this time, Monitoring (RXn8) turns to ON at the
same time.
Monitor data 1 (RWrn): Data demanded by Monitor 1 (RWwn)

Monitor data 2 (RWrn+1): Data demanded by Monitor 2 (RWwn+1)
For 32-bit data, set the lower 16 bits of the monitor code to Monitor 1 (RWwn) and the upper 16 bits to
Monitor 2 (RWwn+1) and read them simultaneously.
The monitor data set to the remote register are always updated while Monitor execution demand (RYn8)
is ON.
When Monitoring (RXn8) turns to OFF, the data set to Monitor data RWrn, RWrn+1 are held. If the
monitor code not in the specifications is set to either Monitor 1 (RWwn) or Monitor 2 (RWwn+1), the
corresponding error code ( 1) is set to Answer code.
3 - 34
(2) When 2 stations are occupied

Monitor 1
(RWwn)
Monitor 2
(RWwn+1)
Monitor execution ON
demand (RYn8)
OFF
Monitoring ON
(RXn8) OFF
Monitor 1 data
lower 16bit (RWrn)
Monitor 1 data
Upper 16bit (RWrn+1)
Monitor 2 data
lower 16bit (RWrn+5)
Monitor 2 data
Upper 16bit (RWrn+6)
Answer code
(RWrn+2)
Data HOLD
Set the monitor codes (refer to section 3.5.3) to Monitor 1 (RWwn) and Monitor 2 (RWwn+1) and turn
Monitor output execution demand (RYn8) to ON. Turning Monitor execution demand (RYn8) to ON sets
the next data. 32-bit data are all divided into the upper 16 bits and lower 16 bits, and set to the remote
register. Data are all hexadecimal numbers. At this time, Monitoring (RXn8) turns to ON at the same
time.
Monitor data 1 lower 16 bit (RWrn): Lower 16 bits of data demanded by Monitor 1 (RWwn)
Monitor data 1 upper 16 bit (RWrn+1): Upper 16 bits of data demanded by Monitor 1 (RWwn)
Monitor data 2 lower 16 bit (RWrn+5): Lower 16 bits of data demanded by Monitor 2 (RWwn+1)
Monitor data 2 upper 16 bit (RWrn+6): Upper 16 bits of data demanded by Monitor 2 (RWwn+1)
A sign is set if data does not exist in RWrn+1 RWrn+6. A “ ” sign is indicated by “0000”, and “ ” by
“FFFF”.
The monitor data set to the remote register are always updated while Monitoring (RXn8) is ON.
When Monitoring (RXn8) turns to OFF, the data set to Monitor data RWrn, RWrn+1, RWrn+5, RWrn+6
are held.
If the monitor code not in the specifications is set to either Monitor 1 (RWwn) or Monitor 2 (RWwn+1), the
corresponding error code ( 1) is set to Answer code.
3 - 35
3.6.2 Instruction codes
(1) Read instruction codes (0000h to 0A1Fh)

Instruction code
(RWwn+2)
Instruction code
execution demand
(RYn9)
Instruction code
(RXn9)
Reading data
(RWrn+3)
Answer code
(RWrn+2)
Data read period
Set the read instruction code (refer to section 3.5.4 (1)) to Instruction code (RWwn+2) and turn
Instruction code execution demand (RYn9) to ON. Turning Instruction code execution demand (RYn9)
to ON sets the data corresponding to the preset read code to Reading data (RWrn+3). Data are all
hexadecimal numbers. At this time, Instruction code execution completion (RXn9) turns to ON at the
same time.
Read the read data set to Reading data (RWrn+3) while Instruction code execution completion (RXn9)
is ON. The data set to Reading data (RWrn+3) is held until the next read instruction code is set and
Instruction code execution demand (RYn9) is turned to ON.
If the instruction code not in the specifications is set to Instruction code (RWwn+2), the corresponding
error code ( 1 ) is set to Answer code. If any unusable parameter, point table is read, the
corresponding error code ( 2 ) is set.
Turn Instruction code execution demand (RYn9) to OFF after completion of data read.
3 - 36
(2) Write instruction codes (8000h to 911Fh)

Instruction code
(RWwn+2)
Writing data
(RWwn+3)
Instruction code
execution demand
(RYn9)
Instruction code Write in execution
processing
Instruction code
(RXn9)
Answer code
(RWrn+2)
Set the write instruction code (refer to section 3.5.4 (2)) to Instruction code (RWwn+2) and the data to
be written (data to be executed) to Writing data (RWwn+3) in hexadecimal, and turn Instruction code
execution demand (RYn9) to ON.
Turning instruction code execution completion to ON sets the data set in Wiring data (RWwn+3) to
the item corresponding to the write instruction code. When write is executed, Instruction code
execution completion (RXn9) turns to ON.
If the instruction code not in the specifications is set to Instruction code (RWwn+2), the corresponding
error code ( 1 ) is set to Answer code.
Turn Instruction code execution demand (RYn9) to OFF after Instruction code execution completion
(RXn9) has turned to ON.
3 - 37
3.6.3 Remote register-based position/speed setting
The functions in this section are usable when Position/speed specifying system selection (RY(n+2)A) is ON
(remote register-based position/speed specifying system is selected) with 2 stations occupied.
The position command/speed command necessary for positioning can be selected by parameter No. 41
setting as indicated below.
Parameter No.41
Set value Position command Speed command

0 Specify the point table No.
1 Set the position Specify the point table No.
2 data. Set the servo motor speed.
(1) When setting the point table No.

Specify the point table No. stored in the servo amplifier and execute positioning.
Preset “ 0” (initial value) in parameter No. 41 to enable point table No.-setting operation.
Point table No.
(RWwn+4)
Position instruction ON
demand
(RY(n+2)0) OFF
Point table No. (Note) Data reserved

designation
Position instruction
execution ON
completion OFF
(RX(n+2)0)
Answer code
(RWrn+2)
8ms
Forward/reverse ON
rotation start
(RYn1 RYn2) OFF
Note. This data is stored into RAM of the servo amplifier. Hence, the data is cleared when power is switched off.
Set the point table No. to point table No. (RWwn+4) and turn Position instruction demand (RY(n+2)0)
to ON.
Turning (RY(n+2)0) to ON stores the position block No. into RAM of the servo amplifier.
When the data is stored, Position instruction execution completion (RX(n+2)0) turns to ON.
If data outside the setting range is set to Position block No. (RWwn+4), the error code (refer to section
3.5.5) is set to Answer code.
Turn Forward rotation start (RYn1)/Reverse rotation start (RYn2) to ON after Position instruction
execution completion (RX(n+2)0) has turned to ON.
3 - 38
(2) When setting the position command data/point table No. (speed command)
Specify the position address with the remote register, and specify the speed command data by
specifying the point table No. to use the preset servo motor speed, acceleration time constant and
deceleration time constant the speed command data, and execute positioning.
Preset “ 1” in parameter No. 41 to enable position command data-set and point table No. (speed
instruction)-setting operation.
Position instruction data
Lower 16bit (RWwn+4)

Upper 16bit (RWwn+5)
Point table No.

(RWwn+6)
demand
(RY(n+2)0) OFF
Speed instruction ON
demand
(RY(n+2)1) OFF
Position data setting
Point table No. (Note) Data reserved
designation
(RX(n+2)0) OFF
(RX(n+2)1) OFF
Answer code
(RWrn+2)
8ms
Forward rotation
Reverse rotation ON
start OFF
(RYn1 RYn2)
Set the lower 16 bits of the position instruction data to Position instruction data lower 16 bit
(RWwn+4), the upper 16 bits of the position instruction data to Position instruction data upper 16 bit
(RWwn+5), and point table for speed command No. to point table No. (RWwn+6), and turn Position
instruction demand (RY(n+2)0) and Speed instruction demand (RY(n+2)1) to ON.
Turning RY(n+2)0 and RY(n+2)1 to ON stores the position command data and point table No. into
RAM of the servo amplifier.
When the data are stored, Position instruction execution completion (RX(n+2)0) and Speed instruction
execution completion (RX(n+2)1) turn to ON.
If data outside the setting range is set to any of Position instruction data lower 16 bit (RWwn+4),
Position instruction data upper 16 bit (RWwn+5) and point table No. (RWwn+6), the error code (refer
to section 3.5.5) is set to Answer code.
Turn Forward rotation start (RYn1) Reverse rotation start (RYn2) to ON after Position instruction
execution completion (RX(n+2)0) and Speed instruction execution completion (RX(n+2)1) have turned
to ON.
3 - 39
(3) When setting the position command data and speed command data
Specify the position address and servo motor speed with the remote register, and execute positioning.
At this time, use the acceleration time constant and deceleration time constant set in point table No. 1.
Preset “ 2” in parameter No. 41 to enable position command data- and speed command data-set
operation.
Lower 16bit (RWwn+4)

Upper 16bit (RWwn+5)
Speed instruction data

(RWwn+6)
demand
(RY(n+2)0) OFF
demand
(RY(n+2)1) OFF
Position speed (Note) Data reserved

data setting
(RX(n+2)0) OFF
(RX(n+2)1) OFF
Answer code
(RWrn+2) 8ms
Forward rotation ON
Reverse rotation OFF
start
(RYn1 RYn2)
Set the lower 16 bits of the position instruction data to Position instruction data lower 16 bit
(RWwn+4), the upper 16 bits of the position instruction data to Position instruction data upper 16 bit
(RWwn+5), and speed instruction data to Speed instruction data (RWwn+6), and turn Position
instruction demand (RY(n+2)0) and Speed instruction demand (RY(n+2)1) to ON.
Turning RY(n+2)0 and RY(n+2)1 to ON stores the position command data and speed command data
into RAM of the servo amplifier.
When the data are stored, Position instruction execution completion (RX(n+2)0) and Speed instruction
execution completion (RX(n+2)1) turn to ON.
If data outside the setting range is set to any of Position instruction data lower 16 bit (RWwn+4),
Position instruction data upper 16 bit (RWwn+5) and Speed command data (RWwn+6), the error code
(refer to section 3.5.5) is set to Answer code.
Turn Forward rotation start (RYn1) Reverse rotation start (RYn2) to ON after Position instruction
execution completion (RX(n+2)0) and Speed instruction execution completion (RX(n+2)1) have turned
to ON.
3 - 40
3.7 Function-by-function programming examples
This section explains specific programming examples for servo operation, monitor, parameter read and
write, and others on the basis of the equipment makeup shown in section 3.7.1.
3.7.1 System configuration example
As shown below, the CC-Link system master local unit is loaded to run two servo amplifiers (1 station
occupied / 2 stations occupied).
X20
Power Master station Input module
CPU
supply (X/Y00 to 1F) (X20 to X2F)
Station No. 1 Station No. 2
Servo amplifier Servo amplifier

(1 station occupied) (2 stations occupied)
3 - 41
3.7.2 Reading the servo amplifier status
Read the status of the servo amplifier from the master station buffer memory. The servo amplifier status
is always stored in the remote input RX (addresses E0H to 15FH). Read the servo amplifier status of
station 1 to M0 M31.
Reads remote input (RX00 to RX1F)

of buffer memory to M0 M31.
Address Remote input

E0H RX0F to RX00 FROM
Station 1 command
E1H RX1F to RX10 M15 M10 M5 M0
E2H RX2F to RX20 RXF to RX0 * 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1
Station 2
E3H RX3F to RX30
In positioning Ready
15EH RX7EF to RX7E0 M31 M26 M21 M16

Station 64 RX1F to RX10 * * * * 1 0 * * * * * * * * * *
15FH RX7FF to RX7F0
Note. area is for one
*: Set 0 or 1 as the bit is Remote station communication ready
not used.
Servo amplifier status (1 station occupied)

M0: Ready (RD) M8: Monitoring (MOF) M16: M24:
M1: In position (INP) M9: Instruction code M17: M25:
M2: Rough match (CPO) execution completion (COF) M18: M26: Trouble (ALM)
M3: Home position return M10: Warning (WNG) M19: M27: Remote station
completion (ZP) M11: Battery warning (BWNG) M20: communication ready
M4: Limiting torque (TLC) M12: Movement finish (MEND) M21: (CRD)
M5: M13: M22: M28:
M6: Electromagnetic brake M14: Position range M23: M29:
interlock (MBR) (POT) M30:
M7: Temporary stop (PUS) M15: M31:
3 - 42
3.7.3 Writing the operation commands
To operate the servo amplifier, write the operation commands to the remote output RY (addresses 160H to
1DFH). Perform positioning operation of point table No. 2 for the servo amplifier of station 2.
Servo-on command (RY00)
Point table No. selection 2 command (RY0B)
Automatic/manual selection command

(RY06)
Forward rotation start command (RY01)
Operation command
Command demand time 10ms
Forward rotation start command reset
Writes M100 to M131 to remote output

(RY00 to RY1F) of buffer memory.
Address
160H RY0F to RY00
M115 M110 M105 M100 TO 1 station
RY0F to RY00 * 0 0 0 1 0 0 0 0 1 1 1 0 0 1 1 command 161H RY1F to RY10
162H RY2F to RY20
2 station
163H RY3F to RY30
Point table selection (bit 1) Automatic/manu Forward Servo ON
al selection rotation start
M131 M126 M121 M116
RY1F to RY10 * * * * * 0 * * * * * * * * * * 1DEH RY7EF to RY7E0
64 station
1DFH RY7FF to RY7F0
Note. area is for one servo amplifier.

*: Set 0 as the bit is not used.
Operation commands (1 station occupied)

M100: Servo-on (SON) M108: Monitor output execution M116: M124:
M101: Forward rotation start (ST1) demand (MOR) M117: M125:
M102: Reverse rotation start (ST2) M109: Instruction code execution M118: M126: Reset (RES)
M103: Proximity dog (DOG) demand (COR) M119: M127:
M104: Forward rotation stroke end M110: Point table No. selection 1 (DI0) M120: M128:
(LSP) M111: Point table No. selection 2 (DI1) M121: M129:
M105: Reverse rotation stroke end M112: Point table No. selection 3 (DI2) M122: M130:
(LSN) M113: Point table No. selection 4 (DI3) M123: M131:
M106: Automatic/manual selection M114: Point table No. selection 5 (DI4)
(MD0) M115:
M107: Temporary stop (STP)
3 - 43
3.7.4 Reading the data
Read various data of the servo amplifier.
(1) Reading the monitor value

Read the (feedback pulse value) of the servo amplifier of station 2 to D10.
Data No. Description

H000A Cumulative feedback pulse data (hexadecimal)
The answer code at instruction code execution is set to D9.

of buffer memory to M200 to M263.
Stores answer code to D9.
Outputs M0 for normal reply.
Read Sets monitor code (H000A) of feedback

setting pulse value to RWW4, RWW5.
Turns on Monitor output execution

demand (RY28).
Reads data to RWR4 and RWR5 of buffer
memory when answer code is normal reply.
Monitor stop
(2) Reading the parameter

Read parameter No. 2 “Function selection 1” of the servo amplifier of station 2 to D1.

H0202 Parameter No. 2 setting (hexadecimal)

Read setting
Writes parameter No. 2 read

(H0202) to RWW6.
Turns on instruction code

execution demand (RY29).
Reads RWR7 of buffer memory to D1
when answer code is normal reply.
Turns off instruction code
execution demand (RY29).

3 - 44
(3) Reading the alarm definition

Read the alarm definition of the servo amplifier of station 2 to D1.

H0010 Occurring alarm/warning No. (hexadecimal)

Read setting
Writes current alarm read (H0010)

to RWW6.
Turns on instruction code execution

demand (RY29).
Reads RWR7 of buffer memory to
D1 when answer code is normal reply.
Turns off instruction code execution
demand (RY29).

3 - 45
3.7.5 Writing the data
This section explains the programs for writing various data to the servo amplifier.
(1) Writing the servo motor speed data of point table

Change the servo motor speed data in the speed block No. 1 of the servo amplifier of station 2 to “100”.
Code No. Description

Write of servo motor speed data of point table No. 1
H8D01
(hexadecimal)
Set data Description

Servo motor speed data of point table No. 1
K100
(decimal)

Read setting In position
Writes speed data (H8D01) of point table

No. 1 to RWW6, and speed data (K100) to
RWW7.

demand (RY29).
Reads RWR6 to D2 when instruction
code execution completion (RX29) turns on.
demand (RY29).

3 - 46
(2) Writing the parameter

Change parameter No. 13 (JOG speed) of the servo amplifier of station 2 to “100”.

H830D Parameter No. 13 write (hexadecimal)

K100 Set data (decimal)

Read setting
Writes parameter No. 13 write (H830D)

to RWW6 and data (K100) to RWW7.

demand (RY29).
Reads RWR6 to D2 when instruction code
execution completion (RX29) turns on.
demand (RY29).

3 - 47
(3) Servo amplifier alarm resetting program examples

(a) Deactivate the alarm of the servo amplifier of station 2 by issuing a command from the
programmable controller. This method is limited to servo alarm occurrence.
Reads remote input (RX20 to RX5F) of

buffer memory to M200 to M263.
Turns on reset command (RY5A).
Reset
command
Turns off reset command (RY5A) if

trouble flag (RX5A) is off.

(b) Deactivate the alarm of the servo amplifier of station 2 using the instruction code.

H8010 Alarm reset command (hexadecimal)

H1EA5 Execution data (hexadecimal)

Reset command
Writes alarm reset command (H8010)

to RWW6 and execution data (H1EA5)
to RWW7.

demand (RY29).
Reads RWR6 to D2 when instruction code
Turns off instruction code execution demand
(RY29).

3 - 48
3.7.6 Operation
This section explains the operation programs of the servo amplifier.
(1) JOG operation

Perform JOG operation of the servo amplifier of station 1 and read the "current position" data.

H0001 Lower 16-bit data of current position (hexadecimal)
H0002 Upper 16-bit data of current position (hexadecimal)

Servo alarm Communication ready
Forward rotation start (RY01)
Forward rotation JOG command
Reverse rotation start (RY02)
Reverse rotation JOG command
Sets monitor code (H0001) of current

position (lower 16 bits) to RWW0.
position (upper 16 bits) to RWW1.
Turns on monitor command (RY08).

Reads RWR0 or RWR1 to D120,
D121 of buffer memory when
Monitoring (RX08) turns on.
CIRCUIT END
3 - 49
(2) Remote register-based position data/speed data setting

Operate the servo amplifier of station 2 after specifying the position data as "100000" and the speed
data as "1000" in the direct specification mode.
Preset " 2" in parameter No. 41.

K100000 Position command data (decimal)
K1000 Speed command data (decimal)
Reads remote input (RX20 to RX5F) of buffer

memory to M200 to M263.
Automatic operation selection (RY26)
Position command selection (RY4A)
Operation In position
command
Writes position command data (K100000)

to RWW8, RWW9, and speed data (K1000)
to RWWA.
Turns on position instruction demand (RY40).
Turns on speed instruction demand (RY41).

Reads RWR6 to D2 when position instruction
execution completion (RX40) and speed
instruction execution completion (RX41) turn
on.
Turns on forward rotation start command
(RY21).
Command request time 10ms
Turns off forward rotation start command

(RY21).
Turns off position instruction demand (RY40).
Turns off speed instruction demand (RY41).
Writes M100 to M163 to remote output (RY20

to RY5F) of buffer memory.
CIRCUIT END
3 - 50
(3) Remote register-based point table No. setting (incremental value command system)
Operate the servo amplifier of station 2 with incremental values after specifying the point table No. 5
in the direct specification mode.
Preset " 0 " in parameter No. 0 and " 2" in parameter No. 41.

K5 Point table No. (decimal)

Position command selection (RY4A)
Incremental value selection (RY4B)
Operation In position
command
Writes point table No. (K5) to RWW8.

Turns on forward rotation start command
(RY21).
Turns off forward rotation start command

(RY21).
Writes M100 to M163 to remote output (RY20

CIRCUIT END to RY5F) of buffer memory.
3 - 51
3.8 Continuous operation program example
This section shows a program example which includes a series of communication operations from a servo
start. The program will be described on the basis of the equipment makeup shown in section 3.8.1, 3.8.3.
3.8.1 System configuration example when 1 station is occupied
As shown below, the CC-Link system master local unit is loaded to run one servo amplifier (1 station
occupied).
Power Master station Input module

CPU
supply (X/Y00 to 1F) (X30 to X3F)
Station No. 1
Servo amplifier
(1 station occupied)
3 - 52
3.8.2 Program example when 1 station is occupied
POINT
To execute a dog type home position return with the CC-Link
communication functions, set " 3 " in parameter No. 116 and use
Proximity dog (DOG) with the remote input (RY03) in this example.
Operate the servo amplifier of station 1 in the positioning mode and read the “current position” data.
Operation: Alarm reset, dog type zeroing, JOG operation, automatic operation under point table
command

H0001 Lower 16-bit data of current position (hexadecimal)
H0002 Upper 16-bit data of current position (hexadecimal)

Writes current alarm read (H0010) to RWW2

at trouble (RY1A) occurrence.
Turns on instruction code execution demand

(RY09).
Reads RWR3 of buffer memory to D11 when
answer code becomes normal reply.
(RY09).
Alarm reset command (RY1A)
Reset
command
Alarm reset command (RY1A) reset

Servo-on command
Automatic/manual operation selection command
Manual operation selection (RY06)
Home position return request
Home position return
command
Forward rotation start request
Forward rotation start request reset
Proximity dog command (RY03)

Proximity dog command
Home position return request reset
Reverse rotation start request
Positioning start command
Positioning In position Rough Home position return
start match completion
command
3 - 53
Positioning start command reset
Point table No. selection command (bit0)

Bit 0 selection
Bit 1 selection
Bit 2 selection
Bit 3 selection
Bit 4 selection

position (lower 16 bits) to RWW0.
position (upper 16 bits) to RWW1.
Turns on monitor output execution demand

(RY08).
Reads RWR0 or RWR1 to D120, D121
of buffer memory when Monitoring
(RX08) turns on.
CIRCUIT END
3.8.3 System configuration example when 2 stations are occupied
As shown below, the CC-Link system master local unit is loaded to run one servo amplifiers (2 station
occupied).
Master
Power Input module
CPU station
supply (X20 to X2F)
(X/Y00 to 1F)
Station No.1
Servo amplifier
(2 station
occupied)
3 - 54
3.8.4 Program example when 2 stations are occupied
POINT
To execute a dog type home position return with the CC-Link
communication functions, set " 3 " in parameter No. 116 and use
Proximity dog (DOG) with the remote input (RY03) in this example.
Operate the servo amplifier of station 1 in the positioning mode and read the “motor speed” data.
Operation: Alarm reset, dog type zeroing, JOG operation, automatic operation under point table
command

H0016 32-bit data of motor speed (hexadecimal)

K5000 Position command data (decimal)
K100 Speed command data (decimal)

Writes current alarm read (H0010) to RWW2

at trouble (RY3A) occurrence.
Turns on instruction code execution demand

(RY09).
Reads RWR3 of buffer memory to D11 when
answer code becomes normal reply.
(RY09).
Alarm reset command (RY3A)
Reset
command
Alarm reset command (RY3A) reset

Servo-on command
Manual operation selection (RY06)
Home position return request
command
Forward rotation start request reset
Proximity dog command (RY03)

Proximity dog command
Home position return request reset
Reverse rotation start request
Positioning instruction selection (RY2A)
Point table/position instruction changing command
3 - 55
Positioning start In position Rough Home position return

command match completion
Writes position command data (K50000) to

RWW4, RWW5, and speed data (K100) to
RWW6.
Turns on speed instruction demand (RY21).

execution completion (RX20) and speed
instruction execution completion (RX21) turn on.
Positioning start command
Positioning start command reset
Turns off speed instruction demand (RY21).
Sets monitor code (H0016) of motor speed

to RWW0.
Turns on monitor output execution demand

(RY08).
Reads RWR0 or RWR1 of buffer memory to
D120, D121 when monitoring (RX08) turns on.
CIRCUIT END
3 - 56
4. SIGNALS AND WIRING
Any person who is involved in wiring should be fully competent to do the work.
Before wiring, turn off the power and wait for 15 minutes or more until the charge
lamp turns off. Then, confirm that the voltage between P and N is safe with a
voltage tester and others. Otherwise, an electric shock may occur. In addition,
always confirm from the front of the servo amplifier whether the charge lamp is off
WARNING or not.
Ground the servo amplifier and the servo motor securely.
Do not attempt to wire the servo amplifier and servo motor until they have been
installed. Otherwise, you may get an electric shock.
The cables should not be damaged, stressed excessively, loaded heavily, or
pinched. Otherwise, you may get an electric shock.
Wire the equipment correctly and securely. Otherwise, the servo motor may
misoperate, resulting in injury.
Connect cables to correct terminals to prevent a burst, fault, etc.
Ensure that polarity ( , ) is correct. Otherwise, a burst, damage, etc. may occur.
The surge absorbing diode installed to the DC relay designed for control output
should be fitted in the specified direction. Otherwise, the signal is not output due to
a fault, disabling the forced stop (EMG) and other protective circuits.
Servo Servo
Amplifier Amplifier
COM COM
(24VDC) (24VDC)
Control Control
CAUTION output
RA
output
RA
signal signal
Use a noise filter, etc. to minimize the influence of electromagnetic interference,

which may be given to electronic equipment used near the servo amplifier.
Do not install a power capacitor, surge suppressor or radio noise filter (FR-BIF
option) with the power line of the servo motor.
When using the regenerative resistor, switch power off with the alarm signal.
Otherwise, a transistor fault or the like may overheat the regenerative resistor,
causing a fire.
Do not modify the equipment.
During power-on, do not open or close the motor power line. Otherwise, a
malfunction or faulty may occur.
POINT
CN1A, CN1B, CN2 and CN3 have the same shape. Wrong connection of
the connectors will lead to a failure. Connect them correctly.
4- 1
4.1 Standard connection example
POINT
As the cable for connection of the servo amplifier and option unit, always
use the MR-J2HBUS05M of 0.5m long. It is not recommended to fabricate
this cable on the user side.
MR-J2S-CP-S084
(Note 3, 7)
CN1A
9 COM
(Note 2, 4) Home position return
18 ZP RA5 completion
(Note 9)
10 RA6
(Note 3, 7) 10m (32.79ft) or less
CN1B
3 VDD (Note 10)
13 COM
(Note 2, 4)
4 CPO RA1 Rough match
(Note 3, 7) 6 MEND RA2 Movement finish

CN1B
Forced stop 18 ALM RA3 Trouble (Note 6)
EMG 15
Forward rotation LSP 16 19 RD RA4 Ready
stroke end
(Note 5) LSN 17
Reverse rotation
stroke end (Note 8)
DOG 7 MR Configurator
Proximity dog
5 (Servo configuration software)
14
(Note 9)
8
MR-JRPCATCBL 3M cable
9
+
SG 10 Personal MR-J2S-T01
SG 20 computer Option unit
SD Plate
CN40
MR-J2HBUS05M cable
CN3
CN30
0.5m or less
(Note 1)
CN10
CC-Link
To Master station,
remote I/O station
4- 2
Note 1. To prevent an electric shock, always connect the protective earth (PE) terminal ( ) of the servo amplifier to the protective earth
(PE) of the control box.
2. Connect the diode in the correct direction. If it is connected reversely, the servo amplifier will be faulty and will not output
signals, disabling the forced stop and other protective circuits.
3. CN1A, CN1B, CN2 and CN3 have the same shape. Wrong connection of the connectors will lead to a fault.
4. The sum of currents that flow in the external relays should be 80mA max. If it exceeds 80mA, supply interface power from
external.
5. When starting operation, always connect the forward/reverse rotation stroke end (LSN/LSP) with SG. (Normally closed
contacts)
6. Trouble (ALM) is connected with COM in normal alarm-free condition.
7. The pins with the same signal name are connected in the servo amplifier.
8. Use MRZJW3-SETUP161E.
9. The signals are not yet assigned in the shipment status.
10. When using the internal power supply (VDD), always connect VDD-COM. Do not connect them when supplying external power.
Refer to section 4.6.2.
4- 3
4.2 Internal connection diagram of servo amplifier
This section gives the internal connection diagram where the signal assignment is in the initial status.
Servo amplifier MR-J2S-T01 option unit
CN1B
24VDC
VDD 3
COM 13
CN1A CN1B CN30

COM 9 18 ALM 2 RXD
Approx.
4.7k
8 19 RD
12 TXD
SG 10, 20 CN1B 9 LG
CN1B 4 CPO
19 SD
5 6 MEND
Approx.
4.7k
DOG 7 18 ALM
Approx.
4.7k
8 19 RD
Approx.
4.7k
9
Approx.
4.7k
14
Approx.
4.7k
EMG 15
Approx.
4.7k
LSP 16
Approx.
4.7k
LSN 17
SG 10, 20
CN3 CN30
CN1A
4- 4
4.3 I/O signals
4.3.1 Connectors and signal arrangements
POINT
The connector pin-outs shown above are viewed from the cable connector
wiring section side.
To the pins left blank in the CN1A/CN1B connectors, input signals can be
assigned by setting parameter No. 116 to 118 and parameter No. 78 to 83.
(1) Signal arrangement

CN1A
CN1B
1 11
1 11
2 12
LG 2 12
3 13 CN10 3 13
4 14 Refer to Section 3.2.2
4 14
VDD COM
5 15 CPO
5 15
6 16
6 16
EMG
7 17 MEND
7 17
8 18
CN10 8 18
DOG
ZP
9 19 ALM
9 19
10 20
COM 10 20
RD
SG SG
SG SG
CN2
CN30
1 11 Connector for connection
CN30 of MR-J2S-T01
2 12
LG LG
LG LG
3 13
CN40 CN40
4 14
3 1
5 15
6 16 SD LG
4 2
MD MDR The connector frames are
7 17 TXD RXD
connected with the PE (earth)
8 18
MR MRR terminal inside the servo amplifier. Refer to Section 15.1.4(3)
P5
9 19 CN3
10 20 Connector for connection
BAT P5
of MR-J2S-CP-S084
P5
4- 5
4.3.2 Signal (devices) explanations
(1) I/O devices

POINT
The devices not indicated in the Connector Pin No. field of the I/O devices
can be assigned to the connector CN1A/CN1B using parameter No. 78 to
83, parameter No. 88 to 90 and parameter No. 116 to 118.
(a) Pins whose devices can be changed

Refer to section 4.6.2 for the I/O interfaces (symbols in the I/O Division field in the table) of the
corresponding connector pins.
Pin type Connector pin No. I/O division Device in initial status
CN1A-8 Without assigned
CN1B-5 Without assigned
CN1B-7 Proximity dog (DOG)
Input-only pins CN1B-9 DI-1 Without assigned
CN1B-15 Forced stop (EMG)
CN1B-16 Forward rotation stroke end (LSP)
CN1B-17 Reverse rotation stroke end (LSN)
The output signal has been assigned in the
I/O pin CN1A-19 DI-1 or DO-1 initial status. Use parameter No. 88 to
determine input or output.
CN1A-18 Home position return completion (ZP)
CN1B-6 Movement finish (MEND)
Output-only pins CN1B-4 DO-1 Rough match (CPO)
CN1B-18 Trouble (ALM)
CN1B-19 Ready (RD)
(b) Input devices
Devices Connector
Device name Functions/Applications
symbol pin No.
Forced stop EMG CN1B-15 Refer to section 3.5.2 (1).
Servo-on SON
Reset RES
Forward rotation stroke end LSP CN1B-16
Reverse rotation stroke end LSN CN1B-17
Forward rotation start ST1
Reverse rotation start ST2
Automatic/manual selection MD0
Proximity dog DOG CN1A-7
Point table No. selection 1 DI0
4- 6
Devices Connector
symbol pin No.
Internal torque limit selection TL2 Refer to section 3.5.2 (1).
Proportion control PC
Temporary stop/Restart STP
Gain changing CDP
(c) Output devices
Devices Connector
symbol pin No.
Trouble ALM CN1B-18 Refer to section 3.5.2 (2).
Ready RD CN1B-19
Movement finish MEND CN1B-6
Rough match CPO CN1B-4
ZP CN1A-18
completion
MBR
interlock
Position range POT
Warning WNG
Battery warning BWNG
Limiting torque TLC
Temporary stop PUS
In position INP
Point No. output 1 PTO
Point No. output 2 PT1
(2) Power supply
Signal Connector
Signal Functions/Applications
symbol pin No.
I/F internal power VDD CN1B-3 Used to output 24V 10% to across VDD-SG.
supply When using this power supply for digital interface, connect it with COM.
Permissible current : 80mA
Digital I/F power COM CN1A-9 Used to input 24VDC (200mA or more) for input interface.
supply input CN1B-13 Connect the positive ( ) terminal of the 24VDC external power supply.
24VDC 10%
Digital I/F common SG CN1A-10 Common terminal for input signals such as SON and EMG. Pins are connected
20 internally.
CN1B-10 Separated from LG.
20
Control common LG CN1A-1 Cannot be used in the MR-J2S-CP-S084.
CN1B-1
CN3- 1
3
11
13
Shield SD Plate Connect the external conductor of the shield cable.
4- 7
4.4 Detailed description of signals (devices)
4.4.1 Forward rotation start Reverse rotation start Temporary stop/Restart
(1) A forward rotation start (RYn1) or a reverse rotation start (RYn2) should make the sequence which
can be used after the main circuit has been established. These signals are invalid if it is switched on
before the main circuit is established.
Normally, it is interlocked with the ready signal (RXn0).
(2) A start in the servo amplifier is made when a forward rotation start (RYn1) or a reverse rotation start
(RYn2) changes from OFF to ON. The delay time of the servo amplifier's internal processing is max.
5ms. The delay time of other signals is max. 10ms.
5ms or less 5ms or less
Servo motor speed

10ms
Forward rotation start (RYn1) or less
or reverse rotation start (RYn2)
8ms or more
Temporary stop/Restart (RYn7)
(3) When a programmable controller is used, the ON time of a forward rotation start (RYn1) or a reverse
rotation start (RYn2) the start/stop (RYn7) signal should be 8ms or longer to prevent a malfunction.
(4) During operation, the forward rotation start (RYn1) or reverse rotation start (RYn2) is not accepted.
The next operation should always be started after the rough match (RXn2) is output with the rough
match output range set to “0” or after the movement finish (RXnC) is output.
4- 8
4.4.2 Movement finish Rough match In position
POINT
If an alarm cause, etc. are removed and servo-on occurs after a stop is
made by servo-off, alarm occurrence or Forced stop (EMG) ON during
automatic operation, Movement finish (RXnC), Rough-match, (RXn2) and
In position (RXn1) are turned on. To resume operation, confirm the
current position and the selected point table No. for preventing
(1) Movement finish

The following timing charts show the output timing relationships between the position command
generated in the servo amplifier and the movement finished (RYnC). This timing can be changed
using parameter No. 6 (in-position range). RYnC turns ON in the servo-on status.
Forward rotation start (RYn1) ON
or reverse rotation start (RYn2) OFF
Position command
5ms or less
Position command and Servo motor speed
servo motor speed
In-position range
ON
Movement finish (RXnC)
OFF
When parameter No. 6 is small

Position command
5ms or less
Position command and Servo motor speed
servo motor speed
In-position range
ON
OFF
When parameter No. 6 is large
(2) Rough match

The following timing charts show the relationships between the signal and the position command
generated in the servo amplifier. This timing can be changed using parameter No. 12 (rough match
output range). RXn2 turns ON in the servo-on status.
Forward rotation start ON Forward rotation start ON

(RYn1) or (RYn1) or
reverse rotation start OFF
(RYn2) reverse rotation start OFF
5ms or less 5ms or less Rough match output range
(RYn2)
Position command Position command
ON ON
Rough match (RXn2) Rough match (RXn2)
OFF OFF
When "0" is set in parameter No. 12 When more than "0" is set in parameter No. 12
4- 9
(3) In position
The following timing chart shows the relationship between the signal and the feedback pulse of the
servo motor. This timing can be changed using parameter No. 6 (in-position range). INP-SG are
connected in the servo-on status.
In-position range
5ms or less
Servo motor speed
ON
In position (RXn1)
OFF
When positioning operation is performed once

or reverse rotation start (RYn2)
OFF
5ms or less
In-position range
Forward
rotation
Servo motor speed
Reverse
rotation
ON
In position (RXn1)
OFF
When servo motor reverses rotation direction during automatic continuous operation
4 - 10
4.4.3 Torque limit
The following table lists the signals and parameters related to the torque limit.
Item Name Remarks

Input signals Internal torque limit selection (RY(n+2)6)
Output signal Limiting torque (RXn4)
No.28 (internal torque limit 1) 0 to 100%
Parameters
No.29 (internal torque limit 2) 0 to 100%
This function limits torque on the assumption that the maximum torque of the servo motor is 100%.
(1) Internal torque limits 1, 2

Use parameter No.28 and 29 to set the internal torque limit. The following graph shows the torque
relative to the setting.
Max. torque
Torque
0
0 100
Torque limit value [%]
(2) Internal torque limit selection (RY(n+2)6)

Internal torque limit selection (RY(n+2)6) may be used to choose the torque limit values made valid.
(Note) Input signals

Torque limit value made valid
RY(n+2)6
0 Internal torque limit 1 (parameter No. 28)
Parameter No. 29 Parameter No. 28: Parameter No. 28
1
Parameter No. 29 Parameter No. 28: Parameter No. 29
Note. 0: off 1: on
4 - 11
4.5 Alarm occurrence timing chart
When an alarm has occurred, remove its cause, make sure that the operation
signal is not being input, ensure safety, and reset the alarm before restarting
CAUTION operation.
As soon as an alarm occurs, turn off Servo-on (RYn0) and power off.
When an alarm occurs in the servo amplifier, the base circuit is shut off and the servo motor is coated to a
stop. Switch off the main circuit power supply in the external sequence. To reset the alarm, switch the
control circuit power supply from off to on, press the "SET" button on the current alarm screen, or turn
the reset (RY(n+1)A or RY(n+3)A) from off to on. However, the alarm cannot be reset unless its cause is
removed.
(Note)
Main circuit
control circuitON Power off Power on
power supply OFF
Base circuit ON
OFF
Dynamic brake Valid
Brake operation Brake operation
Invalid
Servo-on ON
(RYn0) OFF
Ready ON
(RXn0) OFF
Trouble (RX(n+1)A ON
or RX(n+3)A) OFF
1s
Reset (RY(n+1) ON
or RY(n+3)A) OFF 50ms or more 60ms or more
Alarm occurs.
Remove cause of trouble.
Note. Switch off the main circuit power as soon as an alarm occurs.
(1) Overcurrent, overload 1 or overload 2

If operation is repeated by switching control circuit power off, then on to reset the overcurrent
(AL.32), overload 1 (AL.50) or overload 2 (AL.51) alarm after its occurrence, without removing
its cause, the servo amplifier and servo motor may become faulty due to temperature rise.
Securely remove the cause of the alarm and also allow about 30 minutes for cooling before
resuming operation.
(2) Regenerative alarm

If operation is repeated by switching control circuit power off, then on to reset the regenerative
(AL.30) alarm after its occurrence, the external regenerative resistor will generate heat,
resulting in an accident.
(3) Instantaneous power failure

Undervoltage (AL.10) occurs when the input power is in either of the following statuses.
A power failure of the control circuit power supply continues for 60ms or longer and the
control circuit is not completely off.
The bus voltage dropped to 200VDC or less for the MR-J2S- CP-S084, or to 158VDC or less
for the MR-J2S- CP1-S084.
(4) Incremental system

When an alarm occurs, the home position is lost. When resuming operation after deactivating
the alarm, make a home position return.
4 - 12
4.6 Interfaces
4.6.1 Common line
The following diagram shows the power supply and its common line.
Servo amplifier
CN1A CN1A
CN1B 24VDC CN1B RA
VDD
COM ALM, etc.
DO-1
SON, etc.
DI-1 SG MR-J2S-T01
option unit
SG
<Isolated>
LG LG
SD SD
CN3 CN30 CN40
LG
SD
CN2 Servo motor encoder

MR
Servo motor MRR
M
SD
Ground
4 - 13
4.6.2 Detailed description of the interfaces
This section gives the details of the I/O signal interfaces (refer to I/O Division in the table) indicated in
sections 4.3.2. Refer to this section and connect the interfaces with the external equipment.
(1) Digital input interface DI-1

Give a signal with a relay or open collector transistor. Source input is also possible. Refer to (3) in this
section.
For use of internal power supply For use of external power supply
Servo amplifier
Do not connect
24VDC
VDD VDD-COM. Servo amplifier
R: Approx. 4.7k
COM 24VDC
VDD
24VDC
200mA or more R: Approx. 4.7k
COM
For a transistor SON, etc.
Approx. 5mA
SON, etc.
Switch
TR SG
Switch
V CES 1.0V
I CEO 100 A SG
(2) Digital output interface DO-1

A lamp, relay or photocoupler can be driven. Provide a diode (D) for an inductive load, or an inrush
current suppressing resister (R) for a lamp load. (Permissible current: 40mA or less, inrush current:
100mA or less) A maximum of 2.6V voltage drop occurs in the servo amplifier.
(a) Inductive load

24VDC 24VDC Do not connect
VDD VDD VDD-COM.
COM COM
(Note)
Load Load 24VDC
ALM, etc ALM, etc 10%
SG SG
If the diode is not If the diode is not

connected as shown, connected as shown,
the servo amplifier the servo amplifier
will be damaged. will be damaged.
Note. If the voltage drop (maximum of 2.6V) interferes with the

relay operation, apply high voltage (up to 26.4V) from
external source.
4 - 14
(b) Lamp load
VDD VDD VDD-COM.
COM COM
R R (Note)
24VDC
ALM, etc ALM, etc 10%
SG SG

external source.
(3) Source input interface

When using the input interface of source type, all Dl-1 input signals are of source type. Source output
cannot be provided.
SG
SG
R: Approx. 4.7k
(Note) COM R: Approx. 4.7k
COM
For a transistor SON,
Approx. 5mA etc.
Switch
Switch SON,etc.
24VDC
VDD
TR
24VDC
VCES 1.0V 200mA or more
ICEO 100 A
Note. This also applies to the use of the external power supply.
4 - 15
Since no source output is provided, configure the following circuit.
VDD VDD VDD-COM.
COM COM
(Note)
Load Load DC24V
ALM, etc. ALM, etc. 10%
SG SG
If the diode is not connected If the diode is not connected

as shown, the servo amplifier as shown, the servo amplifier
will be damaged. will be damaged.

external source.
4 - 16
4.7 Input power supply circuit
Always connect a magnetic contactor (MC) between the main circuit power supply
and L1, L2, and L3 of the servo amplifier, and configure the wiring to be able to shut
down the power supply on the side of the servo amplifier’s power supply. If a
CAUTION magnetic contactor (MC) is not connected, continuous flow of a large current may
cause a fire when the servo amplifier malfunctions.
Use the trouble (ALM) to switch power off. Otherwise, a regenerative transistor
fault or the like may overheat the regenerative resistor, causing a fire.
4.7.1 Connection example
Wire the power supply and main circuit as shown below so that the servo-on (RYn0) turns off as soon as
alarm occurrence is detected and power is shut off.
A no-fuse breaker (NFB) must be used with the input cables of the power supply.
(1) For 3-phase 200 to 230VAC power supply

Forced
OFF ON
RA stop
MC
MC
SK
NFB MC
Servo amplifier
L1
3-phase
200 to 230 VAC L2
L3
L11
L21
EMG
Forced stop
SG
VDD
COM
ALM RA Trouble
4 - 17
(2) For 1-phase 100 to 120VAC or 1-phase 230VAC power supply

Forced
RA stop OFF ON
MC
MC
SK
Power supply NFB MC

Servo amplifier
1-phase 100 to L1
120VAC or L2
1-phase 230VAC
L3 (Note)
L11
L21
EMG
Forced stop
SG
VDD
COM
ALM RA Trouble
Note. Not provided for 1-phase 100 to 120VAC.
4 - 18
4.7.2 Terminals
The positions and signal arrangements of the terminal blocks change with the capacity of the servo
amplifier. Refer to section 13.1.
Symbol Connection target (Application) Description

Supply L1, L2 and L3 with the following power.
For 1-phase 230VAC, connect the power supply to L1/L2 and leave L3 open.
Servo amplifier MR-J2S-10CP- MR-J2S-100CP- MR-J2S-10CP1-

S084 to S084 to S084 to
Power supply 70CP-S084 700CP-S084 40CP1-S084
L1, L2, L3 Main circuit power supply 3-phase 200 to
L1 L2 L3
230VAC, 50/60Hz
1-phase 230VAC,
L1 L2
50/60Hz
1-phase 100 to
L1 L2
120VAC, 50/60Hz
Connect to the servo motor power terminals (U, V, W). During power-on, do not
U, V, W Servo motor power
open or close the motor power line. Otherwise, a malfunction or faulty may occur.
Servo amplifier MR-J2S-10CP-S084 to MR-J2S-10CP1-S084

Power supply 700CP-S084 to 40CP1-S084
1-phase 200 to 230VAC,
L11, L21 Control circuit power supply L11 L21
50/60Hz
1-phase 100 to 120VAC,
L11 L21
50/60Hz
1) MR-J3-350CP-S084 or less
When using servo amplifier built-in regenerative resistor, connect between P-D
terminals. (Wired by default)
When using regenerative option, disconnect between P-D terminals and connect
regenerative option to P terminal and C terminal.
2) MR-J3-500CP-S084o700CP-S084
P, C, D Regenerative option
MR-J3-500CP-S084 and 700CP-S084 do not have D terminal.
When using servo amplifier built-in regenerative resistor, connect P terminal
and C terminal. (Wired by default)
When using regenerative option, disconnect P terminal and C terminal and
connect regenerative option to P terminal and C terminal.
Refer to sections 15.1.1 for details.
When using the regeneration converter or brake unit, connect it across P-N.
Regeneration converter
N Do not connect it to the servo amplifier of MR-J2S-200CP-S084 or less.
Brake unit
Refer to sections 15.1.2 and 15.1.3 for details.
Connect this terminal to the protective earth (PE) terminals of the servo motor
Protective earth (PE)
and control box for grounding.
4 - 19
4.7.3 Power-on sequence
(1) Power-on procedure

1) Always wire the power supply as shown in above section 4.7.1 using the magnetic contactor with
the main circuit power supply (three-phase 200V: L1, L2, L3, single-phase 230V single-phase 100V:
L1, L2). Configure up an external sequence to switch off the magnetic contactor as soon as an alarm
occurs.
2) Switch on the control circuit power supply L11, L21 simultaneously with the main circuit power
supply or before switching on the main circuit power supply. If the main circuit power supply is not
on, the display shows the corresponding warning. However, by switching on the main circuit power
supply, the warning disappears and the servo amplifier will operate properly.
3) The servo amplifier can accept the servo-on (RYn0) about 1 to 2s after the main circuit power supply
is switched on. Therefore, when servo-on (RYn0) is switched on simultaneously with the main
circuit power supply, the base circuit will switch on in about 1 to 2s, and the ready (RXn0) will
switch on in further about 20ms, making the servo amplifier ready to operate. (Refer to paragraph
(2) in this section.)
4) When the reset (RY(n+1)A or RY(n+3)A) is switched on, the base circuit is shut off and the servo
motor shaft coasts.
(2) Timing chart

Servo-on (RYn0) accepted
(1 to 2s)
Power supply ON
OFF
Base circuit ON
OFF 10ms 10ms 60ms
Servo-on ON
(RYn0) OFF 60ms
Reset (RY(n+1)A ON
or RY(n+3)A) OFF
20ms 10ms 20ms 10ms 20ms 10ms
Ready ON
(RXn0) OFF
Power-on timing chart
4 - 20
(3) Forced stop
Provide an external forced stop circuit to ensure that operation can be stopped and
CAUTION power switched off immediately.
Make up a circuit which shuts off main circuit power as soon as EMG-SG are opened at a forced stop.
To ensure safety, always install an external forced stop switch across EMG-SG. By disconnecting
EMG-SG, the dynamic brake is operated to bring the servo motor to a sudden stop. At this time, the
display shows the servo forced stop warning (AL.E6).
During ordinary operation, do not use the external forced stop (EMG) to alternate stop and run.
The servo amplifier life may be shortened.
Servo amplifier
VDD
COM
EMG
SG
4 - 21
4.8 Connection of servo amplifier and servo motor
4.8.1 Connection instructions
Insulate the connections of the power supply terminals to prevent an electric

WARNING shock.
Connect the wires to the correct phase terminals (U, V, W) of the servo amplifier
and servo motor. Otherwise, the servo motor will operate improperly.
CAUTION
Do not connect AC power supply directly to the servo motor. Otherwise, a fault
may occur.
POINT
Do not apply the test lead bars or like of a tester directly to the pins of the
connectors supplied with the servo motor. Doing so will deform the pins,
causing poor contact.
The connection method differs according to the series and capacity of the servo motor and whether or not
the servo motor has the electromagnetic brake. Perform wiring in accordance with this section.
(1) For grounding, connect the earth cable of the servo motor to the protective earth (PE) terminal ( ) of
the servo amplifier and connect the ground cable of the servo amplifier to the earth via the protective
earth of the control box. Do not connect them directly to the protective earth of the control panel.
Control box
Servo Servo motor

amplifier
PE terminal
(2) Do not share the 24VDC interface power supply between the interface and electromagnetic brake.
Always use the power supply designed exclusively for the electromagnetic brake.
4.8.2 Connection diagram
During power-on, do not open or close the motor power line. Otherwise, a
CAUTION malfunction or faulty may occur.
The following table lists wiring methods according to the servo motor types. Use the connection diagram
which conforms to the servo motor used. For cables required for wiring, refer to section 15.2.1. For
encoder cable connection, refer to section 15.1.4. For the signal layouts of the connectors, refer to section
4.8.3.
For the servo motor connector, refer to chapter 4 of the Servo Motor Instruction Manual.
4 - 22
Servo motor Connection diagram

U (Red)
U
V (White)
V Motor
W (Black)
W
(Green)
(Note 1) 24VDC
B1 (Note 2)
HC-KFS053 (B) to 73 (B)
EMG B2 Electromagnetic
HC-MFS053 (B) to 73 (B) To be shut off when servo-on (RYn0) brake
HC-UFS13 (B) to 73 (B) switches off or by trouble (RX(n+1)A
or RX(n+3)A)
CN2
Encoder cable Encoder
Note 1. To prevent an electric shock, always connect the protective earth (PE) terminal ( ) of the
2. This circuit applies to the servo motor with electromagnetic brake.
U U
V V Motor
W W
(Note 1) 24VDC
B1
HC-SFS121 (B) to 301 (B) (Note 2)
B2
HC-SFS202 (B) to 702 (B)
EMG Electromagnetic
HC-SFS203 (B) 353 (B) To be shut off when servo-on (RYn0) brake
HC-UFS202 (B) to 502 (B) switches off or by trouble (RX(n+1)A
or RX(n+3)A)
HC-RFS353 (B) to 503 (B)
CN2

U U
V V Motor
W W
(Note 1) 24VDC
B1
HC-SFS81(B) (Note 2)
B2
HC-SFS52 (B) to 152 (B)
EMG Electromagnetic
HC-SFS53 (B) to 153 (B) To be shut off when servo-on (RYn0) brake
HC-RFS103 (B) to 203 (B) switches off or by trouble (RX(n+1)A
or RX(n+3)A)
HC-UFS72 (B) 152 (B)
CN2
4 - 23
4.8.3 I/O terminals
(1) HC-KFS HC-MFS HC-UFS3000r/min series
Power supply lead Encoder connector signal arrangement

4-AWG19 0.3m (0.98ft.)
1 2 3
Power supply connector (Molex)
MR MRR BAT
Without electromagnetic brake
a 5557-04R-210 (receptacle) 4 5 6
Encoder cable 0.3m (0.98ft.) 5556PBTL (Female terminal) MD MDR
With connector 1-172169-9 b 7 8 9
With electromagnetic brake
(Tyco Electronics) 5557-06R-210 (receptacle) P5 LG SHD
5556PBTL (Female terminal)

Power supply Power supply View a
connector connector
Pin Signal Pin Signal
5557-04R-210 5557-06R-210
1 U 1 U
1 3 2 V 1 4 2 V
2 4 3 W 2 5 3 W
4 (Earth) 3 6 4 (Earth)
View b
5 (Note) B1
View b
6 (Note) B2
Note. For the motor with
electromagnetic brake,
supply electromagnetic
brake power (24VDC).
There is no polarity.
4 - 24
(2) HC-SFS HC-RFS HC-UFS2000 r/min series
Servo motor side connectors

Servo motor Electromagnetic
For power supply For encoder
brake connector
HC-SFS81(B) The connector
CE05-2A22-
HC-SFS52(B) to 152(B) for power is
23PD-B
HC-SFS53(B) to 153(B) shared.
HC-SFS121(B) to 301(B)
CE05-2A24-
HC-SFS202(B) to 502 (B)
17PD-B MS3102A10SL-
HC-SFS203(B) 353(B)
4P
CE05-2A32-
HC-SFS702(B)
17PD-B MS3102A20-
a
CE05-2A22- 29P
HC-RFS103(B) to 203 (B)
Encoder connector 23PD-B
b The connector
CE05-2A24-
HC-RFS353(B) 503(B) for power is
Brake connector c Power supply connector 10PD-B
shared.
CE05-2A22-
HC-UFS72(B) 152(B)
23PD-B
CE05-2A24- MS3102A10SL-
HC-UFS202(B) to 502(B)
10PD-B 4P
Power supply connector signal arrangement
CE05-2A22-23PD-B CE05-2A24-10PD-B CE05-2A32-17PD-B
Key Key Key

Pin Signal Pin Signal Pin Signal
F
A U F A
A U A U
G A
B V B V D A B V
B E B
H
C
C W G C W C W
E D C B
C D (Earth) D (Earth)
D D (Earth)
E E (Note) B1
View c View c
F F (Note) B2
G (Note) B1 G
H (Note) B2 Note. For the motor with
Note. For the motor with electromagnetic brake,
electromagnetic brake, supply electromagnetic
supply electromagnetic brake power (24VDC).
brake power (24VDC). There is no polarity.
There is no polarity.
Encoder connector signal arrangement Electromagnetic brake connector signal arrangement
MS3102A20-29P MS3102A10SL-4P
Key Key
Pin Signal
Pin Signal Pin Signal
M A BC A (Note)B1
L N A MD K
K T P D B (Note)B2
J E
B MDR L A B
H
S R
F C MR M Note. For the motor with
G
D MRR N SD electromagnetic brake,
View a View b supply electromagnetic
E P
brake power (24VDC).
F BAT R LG There is no polarity.
G LG S P5
H T
J
4 - 25
4.9 Servo motor with electromagnetic brake
Configure the electromagnetic brake operation circuit so that it is activated not only
by the servo amplifier signals but also by an external forced stop (EMG).
Contacts must be open when
servo-on (RYn0) is off or when a Circuit must be
trouble (RY(n+1)A or RX(n+3)A) is opened during
present and when an electromagnetic forced stop (EMG).
brake interlock (MBR).
Servo motor
RA EMG
CAUTION 24VDC
The electromagnetic brake is provided for holding the motor shaft. Do not use it for
ordinary braking.
Before performing the operation, be sure to confirm that the electromagnetic brake
operates properly.
POINT
For the power supply capacity, operation delay time and other
specifications of the electromagnetic brake, refer to the Servo Motor
Instruction Manual.
Note the following when the servo motor equipped with electromagnetic brake is used.
1) In the device setting of the MR Configurator (Servo Configuration software), make the
electromagnetic brake interlock (MBR) available.
2) Do not share the 24VDC interface power supply between the interface and electromagnetic brake.
Always use the power supply designed exclusively for the electromagnetic brake.
3) The brake will operate when the power (24VDC) switches off.
4) While the reset (RY(n+1)A or RY(n+3)A) is on, the base circuit is shut off. When using the servo
motor with a vertical shaft, use the electromagnetic brake interlock (MBR).
5) Turn off the servo-on (RYn0) after the servo motor has stopped.
(1) Connection diagram

Forced
RA stop B1
VDD
COM Z
MBR RA
24VDC B2
4 - 26
(2) Setting
1) In the device setting of the MR Configurator (Servo Configuration Software), make the
electromagnetic brake interlock (MBR) available.
2) Using parameter No. 33 (electromagnetic brake sequence output), set a time delay (Tb) at servo-off
from electromagnetic brake operation to base circuit shut-off as in the timing chart shown in (3) in
this section.
(3) Timing charts

(a) Servo-on (RYn0) command (from controller) ON/OFF
Tb (ms) after servo-on (RYn0) is switched off, servo lock is released and the servo motor coasts.
If the electromagnetic brake is made valid in the servo lock status, the brake life may be shorter.
For use in vertical lift and similar applications, therefore, set delay time (Tb) to the time which is
about equal to the electromagnetic brake operation delay time and during which the load will not
drop.
Coasting
Servo motor speed 0 r/min
(60ms) Tb
ON
Base circuit
OFF
(80ms) Electromagnetic
Electromagnetic (Note 1) ON brake operation
brake interlock delay time
(MBR) OFF
ON
Servo-on(RYn0)
OFF
(Note 3)
Forward rotation start ON
(RYn1) or reverse
rotation start (RYn2) OFF
Electromagnetic Release
brake Activate
Release delay time and external relay (Note 2)
Note 1. ON: Electromagnetic brake is not activated.

OFF: Electromagnetic brake is activated.
2. Electromagnetic brake is released after delaying for the release delay time of electromagnetic brake and operation time of
external circuit relay. For the release delay time of electromagnetic brake, refer to the Servo Motor Instruction Manual.
3. After the electromagnetic brake is released, turn ON the RYn1 or RYn2.
4 - 27
(b) Forced stop (EMG) ON/OFF

Dynamic brake
Dynamic brake
Forward Electromagnetic brake
Servo motor speed Electromagnetic brake
rotation
Electromagnetic brake release
0r/min
(10ms) (180ms)
ON
Base circuit
OFF
(180ms)
Electromagnetic (Note) ON Electromagnetic brake
brake interlock (MBR) operation delay time
OFF
Invalid (ON)
Forced stop (EMG)
Valid (OFF)
Note. ON: Electromagnetic brake is not activated.

(c) Alarm occurrence

Dynamic brake
Dynamic brake
Forward Electromagnetic brake
Servo motor speed
rotation Electromagnetic brake
0r/min
(10ms)
ON
Base circuit
OFF
(Note) ON Electromagnetic brake

Electromagnetic
brake interlock (MBR) operation delay time
OFF
No (ON)
Trouble (RX(n+1)A or
RX(n+3)A) Yes (OFF)
Note. ON: Electromagnetic brake is not activated.

4 - 28
(d) Both main and control circuit power supplies off

Dynamic brake
Dynamic brake
(10ms) Electromagnetic brake
Forward
Servo motor speed (Note 1)
rotation 15 to 60ms Electromagnetic brake
0r/min
ON
Base circuit
OFF
Electromagnetic (Note 2) ON
brake interlock (MBR)
OFF
No (ON) operation delay time
RX(n+3)A) Yes (OFF)
Main circuit ON
power
Control circuit OFF
Note 1. Changes with the operating status.

2. ON: Electromagnetic brake is not activated.
(e) Only main circuit power supply off (control circuit power supply remains on)
Dynamic brake
Dynamic brake
(10ms) Electromagnetic brake
Forward
Servo motor speed (Note 1)
rotation 15 or more Electromagnetic brake
0r/min
ON
Base circuit
OFF
(Note 3) ON
Electromagnetic
brake interlock (MBR) OFF
No (ON) operation delay time
(Note 2)
RX(n+3)A) Yes (OFF)
Main circuit ON
power supply OFF
Note 1. Changes with the operating status.

2. When the main circuit power supply is off in a motor stop status, the main circuit off warning (AL.E9) occurs and the
trouble (RX(n+1)A or RX(n+3)A) does not turn off.
3. ON: Electromagnetic brake is not activated.
4 - 29
4.10 Grounding
Ground the servo amplifier and servo motor securely.

WARNING To prevent an electric shock, always connect the protective earth (PE) terminal of
the servo amplifier with the protective earth (PE) of the control box.
The servo amplifier switches the power transistor on-off to supply power to the servo motor. Depending on
the wiring and ground cable routing, the servo amplifier may be affected by the switching noise (due to
di/dt and dv/dt) of the transistor. To prevent such a fault, refer to the following diagram and always
ground.
To conform to the EMC Directive, refer to the EMC Installation Guidelines (IB (NA) 67310).
Control box
Servo motor
NFB MC Servo amplifier
CN2
L1
(Note) Encoder
Line filter
Power supply L2
L3
L11
U U
L21
V V M
W W
CN3
CN30
Programmable
controller
CN10
Ensure to connect it to PE
MR-J2S-T01 terminal of the servo amplifier.
Do not connect it directly to
the protective earth of
the control panel.
Outer
Protective earth(PE) box
Note. For 1-phase 230VAC, connect the power supply to L1 L2 and leave L3 open.
There is no L3 for 1-phase 100 to 120VAC power supply. Refer to section 1.2 for the power supply specification.
4 - 30
4.11 Servo amplifier terminal block (TE2) wiring method
POINT
Refer to Table 15.1 in section 15.2.1 for the cable size used for the cable.
4.11.1 For the servo amplifier produced later than Jan. 2006
(1) Termination of the cables

(a) Solid wire
After the sheath has been stripped, the cable can be used as it is.
Sheath Core
Approx. 10mm
(b) Twisted wire

1) When the wire is inserted directly
Use the cable after stripping the sheath and twisting the core. At this time, take care to avoid a
short caused by the loose wires of the core and the adjacent pole. Do not solder the core as it may
cause a contact fault. Alternatively, a bar terminal may be used to put the wires together.
2) When the wires are put together

Using a bar terminal.
Cable Size Bar Terminal Type
Crimping Tool Manufacturer
[mm2] AWG For 1 cable For 2 cables
1.25/1.5 16 AI1.5-10BK AI-TWIN 1.5-10BK
CRIMPFOX ZA 3 Phoenix Contact
2/2.5 14 AI2.5-10BU
Cut the wire running out of bar terminal to less than 0.5mm.
Less than 0.5mm
When using a bar terminal for two wires, insert the wires in the direction where the insulation
sleeve does not interfere with the next pole and pressure them.
Pressure
Pressure
4 - 31
(2) Termination of the cables

(a) When the wire is inserted directly
Insert the wire to the end pressing the button with a small flat blade screwdriver or the like.
Button
Small flat blade

screwdriver or the like When removing the short-circuit bar
from across P-D, press the buttons
of P and D alternately pulling the
short-circuit bar. For the installation,
Twisted wire
insert the bar straight to the end.
(b) When the wires are put together using a bar terminal
Insert a bar terminal with the odd-shaped side of the pressured terminal on the button side.
Bar terminal for one

wire or solid wire
Bar terminal for two wires
4 - 32
4.11.2 For the servo amplifier produced earlier than Dec. 2005
1) Termination of the cables

Solid wire: After the sheath has been stripped, the cable can be used as it is.
Approx. 10mm
(0.39inch)
Twisted wire: Use the cable after stripping the sheath and twisting the core. At this time, take
care to avoid a short caused by the loose wires of the core and the adjacent pole.
Do not solder the core as it may cause a contact fault. Alternatively, a bar
terminal may be used to put the wires together.
Cable size Bar terminal type

2 Crimping tool Manufacturer
[mm ] AWG For 1 cable For 2 cables
1.25/1.5 16 AI1.5-10BK AI-TWIN 1.5-10BK CRIMPFOX ZA3
or Phoenix Contact
2/2.5 14 AI2.5-10BU
CRIMPFOX UD 6
2) Connection
Insert the core of the cable into the opening and tighten the screw with a flat-blade screwdriver
so that the cable does not come off. (Tightening torque: 0.3 to 0.4N m (2.7 to 3.5Ib in)) Before
inserting the cable into the opening, make sure that the screw of the terminal is fully loose.
When using a cable of 1.5mm2 or less, two cables may be inserted into one opening.
4 - 33
Flat-blade screwdriver
Tip thickness 0.4 to 0.6mm (0.016 to 0.024in.)
Overall width 2.5 to 3.5mm (0.098 to 0.138in.)
To loosen. To tighten.
Cable
Opening
Control circuit terminal block
Use of a flat-blade torque screwdriver is recommended to manage the screw tightening torque. The
following table indicates the recommended products of the torque screwdriver for tightening torque
management and the flat-blade bit for torque screwdriver. When managing torque with a Phillips bit,
please consult us.
Product Model Manufacturer/Representative

Torque screwdriver N6L TDK Nakamura Seisakusho
Bit for torque screwdriver B-30, flat-blade, H3.5 X 73L Shiro Sangyo
4 - 34
4.12 Instructions for the 3M connector
When fabricating an encoder cable or the like, securely connect the shielded external conductor of the
cable to the ground plate as shown in this section and fix it to the connector shell.
External conductor Sheath Core Sheath

External conductor
Strip the sheath. Pull back the external conductor to cover the sheath
Screw
Cable
Screw
Ground plate
4 - 35
MEMO
4 - 36
5. OPERATION
5. OPERATION
POINT
In the shipment status, Forward rotation stroke end (LSP), Reverse rotation
stroke end (LSN) and Proximity dog (DOG) are valid as the CN1A/CN1B
external input signals. However, this chapter explains them with the register
No. of the remote input.
5.1 When switching power on for the first time
5.1.1 Pre-operation checks
Before starting operation, check the following.
(1) Wiring
(a) A correct power supply is connected to the power input terminals (L1, L2, L3, L11, L21) of the servo
amplifier.
(b) The servo motor power terminals (U, V, W) of the servo amplifier match in phase with the power
input terminals (U, V, W) of the servo motor.
(c) The servo motor power terminals (U, V, W) of the servo amplifier are not shorted to the power input
terminals (L1, L2, L3) of the servo motor.
(d) The earth terminal of the servo motor is connected to the PE terminal of the servo amplifier.
(e) Note the following when using the regenerative option, brake unit or power regeneration converter.
1) For the MR-J2S-350CP-S084 or less, the lead has been removed from across D-P of the control
circuit terminal block, and twisted cables are used for its wiring.
2) For the MR-J2S-500CP-S084 or more, the lead has been removed from across P-C of the servo
amplifier built-in regenerative resistor, and twisted cables are used for its wiring.
(f) When stroke end limit switches are used, the signals across LSP-SG and LSN-SG are on during
operation.
(g) 24VDC or higher voltages are not applied to the pins of connectors CN1A and CN1B.
(h) SD and SG of connectors CN1A and CN1B are not shorted.
(i) The wiring cables are free from excessive force.
(2) Environment
Signal cables and power cables are not shorted by wire offcuts, metallic dust or the like.
(3) Machine
(a) The screws in the servo motor installation part and shaft-to-machine connection are tight.
(b) The servo motor and the machine connected with the servo motor can be operated.
5- 1
5. OPERATION
5.1.2 Startup
WARNING Do not operate the switches with wet hands. You may get an electric shock.
Before starting operation, check the parameters. Some machines may perform
Take safety measures, e.g. provide covers, to prevent accidental contact of hands
and parts (cables, etc.) with the servo amplifier heat sink, regenerative resistor,
CAUTION servo motor, etc.since they may be hot while power is on or for some time after
power-off. Their temperatures may be high and you may get burnt or a parts may
damaged.
During operation, never touch the rotating parts of the servo motor. Doing so can
cause injury.
Connect the servo motor with a machine after confirming that the servo motor operates properly alone.
For startup reference, a single machine structure will be described. Refer to this section and start up the
machine safely.
(1) Machine conditions

P
Servo amplifier Reduction ratio Ballscrew

1/n 1/2 PB PB 10mm(0.39inch)
Position data (P) 200mm(787.40inch)

Servo motor Speed (V) 2500r/min
HC-MFS131072pulse/rev Ta Tb Acceleration time constant (Ta) 200ms
V Deceleration time constant (Tb) 300ms
Regenerative Servo motor
option speed 0r/min
MR-RB032
Point table No. 1
1) Absolute position detection system used
2) Command resolution: 10 m
3) Command system: Absolute value command system
4) Electronic gear calculation
CMX(pulse) 131072 131072 131072 32768

1 1 ................................................ (5.1)
CDV( m) 5000 1250
1000 10 1000
n PB 2
CMX 32768
CDV 1250
5) For the device command method, external input signals are used by the point table selection,
forward rotation start (RYn1), servo-on (RYn0) and other commands.
6) Point table No.1 is used to execute automatic operation once.
5- 2
5. OPERATION
(2) Startup procedure

(a) Power on
1) Switch off the servo-on (RYn0).
2) When main circuit power/control circuit power is switched on, "PoS" (Current position) appears
on the servo amplifier display.
In the absolute position detection system, first power-on results in the absolute position lost
(AL.25) alarm and the servo system cannot be switched on. This is not a failure and takes place
due to the uncharged capacitor in the encoder.
The alarm can be deactivated by keeping power on for a few minutes in the alarm status and
then switching power off once and on again.
Also in the absolute position detection system, if power is switched on at the servo motor speed
of 500r/min or higher, position mismatch may occur due to external force or the like. Power must
therefore be switched on when the servo motor is at a stop.
(b) Test operation
Using jog operation in the "test operation mode" of the MR Configurator (Servo Configuration
Software), operated at the speed as low as possible, check whether the servo motor rotates
correctly. (Refer to section 7.7.1, 8.9.2)
(c) Parameter setting
Set the parameters according to the structure and specifications of the machine. Refer to chapter 5
for the parameter definitions and to sections 7.4 and 8.6 for the setting method.
Parameter Name Setting Description
20
Command system, regenerative
No.0 Absolute value command system.
option selection
MR-RB032 regenerative option is used.
10
When forward rotation start (RYn1) is
valid, address is incremented in CCW
No.1 Feeding function selection direction.
Since command resolution is 10 times,
feed length multiplication factor of 10
times is selected.
1
No.2 Function selection 1
Absolute position detection system.
No.4 Electronic gear numerator (CMX) 32768 From calculation result of formula (5.1)
No.5 Electronic gear denominator (CDV) 1250 From calculation result of formula (5.1)
After setting the above parameters, switch power off once. Then switch power on again to make the
set parameter values valid.
(d) Point table setting
Set the point table according to the operation pattern. Refer to section 5.2 for the point table
definitions and to sections 7.5 and 8.5 for the setting method.
Position data Servo motor Acceleration time Deceleration time Dwell [ms] Auxiliary
[ 10STM m] speed [r/min] constant [ms] constant [ms] function
20000 2500 200 300 0 0
(e) Servo-on
Switch the servo-on in the following procedure.
1) Switch on main circuit/control circuit power.
2) Switch on the servo-on (RYn0).
When placed in the servo-on status, the servo amplifier is ready to operate and the servo motor is
locked. By using the sequence in the diagnostic mode in section 8.3, the ready status can be shown
on the servo amplifier display. In the operation-ready status, the following screen appears.
5- 3
5. OPERATION
(f) Home position return

Perform home position return as required. Refer to section 5.4 for home position return types. A
parameter setting example for dog type home position return is given here.
Parameter Name Setting Description
000
Dog type home position return is selected.
Home position return is started in address
No.8 Home position return type
incremented direction.
Proximity dog (RYn3) is valid when DOG-
SG are opened.
No.9 Home position return speed 1000 Motion is made up to proximity dog at 1000r/min.
No.10 Creep speed 10 Motion is made up to home position at 10r/min.
No.11 Home position shift distance 0 No home position shift
Set the current position at home position return
No.42 Home position return position data
completion.
No.43 Moving distance after proximity dog Not used in dog type home position return.
After setting the above parameters, switch power off once. Then switch power on again to make the
set parameter values valid.
Set the input signals as listed below and switch on the forward rotation start (RYn1) to execute
home position return.
Device name Symbol ON/OFF Description
Automatic/manual selection RYn6 ON
Point table No. selection 1 RYnA OFF Home position return mode is selected.
Point table No. selection 2 RYnB OFF
Forward rotation stroke end RYn4 ON CCW rotation side limit switch is turned on.
Reverse rotation stroke end RYn5 ON CW rotation side limit switch is turned on.
Servo-on RYn0 ON Servo is switched on.
(g) Automatic operation

Set the input signals as listed below and switch on the forward rotation start (RYn1) to execute
automatic operation in accordance with point table No.1.
Device name Symbol ON/OFF Description
Automatic/manual selection RYn6 ON Automatic operation mode is selected.
Servo-on RYnA ON Servo is switched on.
Forward rotation stroke end RYnB ON CCW rotation side limit switch is turned on.
Reverse rotation stroke end RYn4 ON CW rotation side limit switch is turned on.
Point table No. selection 1 RYn5 ON
Point table No.1 is selected.
Point table No. selection 2 RYn0 OFF
(h) Stop
In any of the following statuses, the servo amplifier interrupts and stops the operation of the servo
motor.
When the servo motor used is equipped with an electromagnetic brake, refer to section 4.9 (3). Note
that forward rotation stroke end (RYn4), reverse rotation stroke end (RYn5) off has the same
stopping pattern as described below.
1) Servo-on (RYn0) OFF
The base circuit is shut off and the servo motor coasts.
2) Alarm occurrence
When an alarm occurs, the base circuit is shut off and the dynamic brake is operated to bring the
servo motor to a sudden stop.
3) Forced stop (EMG) OFF
The base circuit is shut off and the dynamic brake is operated to bring the servo motor to a
sudden stop. Servo forced stop warning (AL.E6) occurs.
4) Forward rotation stroke end (RYn4), reverse rotation stroke end (RYn5) OFF
The droop pulse value is erased and the servo motor is stopped and servo-locked. It can be run in
the opposite direction.
5- 4
5. OPERATION
5.2 Automatic operation mode
5.2.1 What is automatic operation mode?
(1) Command system

After selection of preset point tables using the input signals or communication, operation is started by
the forward rotation start (RYn1) or reverse rotation start (RYn2). Automatic operation has the
absolute value command system, incremental value command system.
(a) Absolute value command system
As position data, set the target address to be reached.
Setting range: 999999 to 999999 [ 10STM m] (STM feed length multiplication parameter No.1)
999999 999999
Position data setting range

STM
[ 10 m]
(b) Incremental value command system

As position data, set the moving distance from the current address to the target address.
Setting range: 0 to 999999 [ 10STM m] (STM feed length multiplication parameter No.1)
Current address Target address
Position data |target address - current address|
(2) Point table

(a) Point table setting
Up to 15 point tables may be set.
Set the point tables using the MR Configurator (Servo Configuration) Software, servo amplifier
operation section or CC-Link write instruction code.
The following table lists what to set: Refer to section 5.2.2 for details of the settings.
Name Description
Position data Set the position data for movement.
Servo motor speed Set the command speed of the servo motor for execution of positioning.
Acceleration time constant Set the acceleration time constant.
Deceleration time constant Set the deceleration time constant.
Dwell Set the waiting time when performing automatic continuous operation.
Auxiliary function Set when performing automatic continuous operation.
(b) Selection of point table

Using the input signal or CC-Link, select the point table No. with the remote input and remote
register from the command device (controller) such as a personal computer.
The following table lists the point table No. selected in response to the remote input. When 2
stations are occupied, the point table No. can be selected by remote register setting. (Refer to
section 3.6.3.)
5- 5
5. OPERATION
(Note) Remote input

Selected point table No.
RYnE RYnD RYnC RYnB RYnA
0 0 0 0 0 0 (Manual home position return mode)
0 0 0 0 1 1
0 0 0 1 0 2
0 0 0 1 1 3
0 0 1 0 0 4
0 0 1 0 1 5
0 0 1 1 0 6
0 0 1 1 1 7
0 1 0 0 0 8
0 1 0 0 1 9
0 1 0 1 0 10
0 1 0 1 1 11
0 1 1 0 0 12
0 1 1 0 1 13
0 1 1 1 0 14
0 1 1 1 1 15
1 0 0 0 0 16
1 0 0 0 1 17
1 0 0 1 0 18
1 0 0 1 1 19
1 0 1 0 0 20
1 0 1 0 1 21
1 0 1 1 0 22
1 0 1 1 1 23
1 1 0 0 0 24
1 1 0 0 1 25
1 1 0 1 0 26
1 1 0 1 1 27
1 1 1 0 0 28
1 1 1 0 1 29
1 1 1 1 0 30
1 1 1 1 1 31
Note. 0: OFF
1: ON
5- 6
5. OPERATION
5.2.2 Automatic operation using point table
(1) Absolute value command system

(a) Point table
Set the point table values using the MR Configurator (Servo Configuration software), from the
servo amplifier operating section or the remote register of CC-Link.
Set the position data, motor speed, acceleration time constant, deceleration time constant, dwell
and auxiliary function to the point table. The following table gives a setting example. However, this
function cannot be used when the point table No. is selected using the remote register of CC-Link.
Name Setting range Unit Description

(1) When using this point table as absolute value command system
Set the target address (absolute value).
Position data 999999 to 999999 10STM m (2) When using this point table as incremental value command system
Set the moving distance. A "-" sign indicates a reverse rotation
command.
Set the command speed of the servo motor for execution of positioning.
Motor speed 0 to permissible speed r/min The setting should be equal to or less than the instantaneous permissible
speed of the servo motor.
Acceleration
0 to 20000 ms Set the time until the rated speed of the servo motor is reached.
time constant
Deceleration
0 to 20000 ms Set the time until the servo motor running at rated speed comes to a stop.
time constant
This function is valid when the point table is selected using the input
signal or the remote input of CC-Link. It cannot be used when the point
table No. is selected using the remote register of CC-Link.
Set "0" in the auxiliary function to make the dwell invalid.
Dwell 0 to 20000 ms Set "1" in the auxiliary function and 0 in the dwell to perform continuous
operation.
When the dwell is set, the position command of the selected point table is
completed, and after the set dwell has elapsed, the position command of
the next point table is started.
(1) When using this point table in the absolute value command system
0: Automatic operation is performed in accordance with a single point
table chosen.
1: Operation is performed in accordance with consecutive point tables
without a stop.
Auxiliary
0 to 3 (2) When using this point table in the incremental value command system
function
table chosen.
3: Operation is performed in accordance with consecutive point tables
without a stop.
When a different rotation direction is set, smoothing zero (command
output) is confirmed and the rotation direction is then reversed.
Setting "1" in point table No.31 results in an error.
For full information, refer to (4) in this section.
(b) Parameter setting

Set the following parameters to perform automatic operation.
1) Command mode selection (parameter No.0)
Select the absolute value command system.
Parameter No. 0
0
Absolute value command system
5- 7
5. OPERATION
2) Forward rotation start coordinate system selection (parameter No.1)

Choose the servo motor rotation direction at the time when the forward rotation start (RYn1) is
switched on.
Servo motor rotation direction
Parameter No. 1 setting
when forward rotation start (RYn1) is switched on
CCW rotation with position data
0
CW rotation with position data
CW rotation with position data
1
CCW rotation with position data
CCW
CW
3) Feed length multiplication selection (parameter No.1)

Set the unit multiplication factor (STM) of position data.
Parameter No.1 setting Feed unit [μm] Position data input range [mm]
0 1 999.999 to 999.999
1 10 9999.99 to 9999.99
2 100 99999.9 to 99999.9
3 1000 999999 to 999999
(c) Operation
Choosing the point table using RYnA to RYnE and turning RYn1 ON starts positioning to the
position data at the preset speed, acceleration time constant and deceleration time constant. At
this time, reverse rotation start (RYn2) is invalid.
Item Setting method Description
Automatic operation mode selection Automatic/manual selection (RYn6) Turn RYn6 ON.
Point table No. selection 1 (RYnA)
Point table No. selection 2 (RYnB)
Point table selection Point table No. selection 3 (RYnC) Refer to section 5.2.1 (2).
Point table No. selection 4 (RYnD)
Point table No. selection 5 (RYnE)
Start Forward rotation start (RYn1) Turn RYn1 ON to start.
5- 8
5. OPERATION
(2) Incremental value command system

(a) Point table
Set the point table values using the MR Configurator (Servo Configuration software), from the
servo amplifier operating section or the remote register of CC-Link.
Set the position data, motor speed, acceleration time constant, deceleration time constant, dwell
and auxiliary function to the point table. The following table gives a setting example.
Name Setting range Unit Description

Set the moving distance.
Position data 0 to 999999 10STM m The unit can be changed using feed length multiplication factor selection
of parameter No. 1.
Set the command speed of the servo motor for execution of positioning.
Servo motor
0 to permissible speed r/min The setting should be equal to or less than the instantaneous permissible
speed
speed of the servo motor.
Acceleration
0 to 20000 ms Set the time until the rated speed of the servo motor is reached.
time constant
Deceleration Set the time until the servo motor running at rated speed comes to a
0 to 20000 ms
time constant stop.
Set "0" in the auxiliary function to make the dwell invalid.
Dwell 0 to 20000 ms Set "1" in the auxiliary function and 0 in the dwell to perform continuous
operation.
When the dwell is set, the position command of the selected point table is
completed, and after the set dwell has elapsed, the position command of
the next point table is started.
table chosen.
Auxiliary
0 1 1: Operation is performed in accordance with consecutive point tables
function
without a stop.
When a different rotation direction is set, smoothing zero (command
output) is confirmed and the rotation direction is then reversed.
Setting "1" in point table No.31 results in an error.
For full information, refer to (4) in this section.
(b) Parameter setting

Set the following parameters to perform automatic operation.
1) Command mode selection (parameter No.0)

Select the incremental value command system.
Parameter No. 0
1
Incremental value command system
5- 9
5. OPERATION
2) ST1 coordinate system selection (parameter No.1)

Choose the servo motor rotation direction at the time when the forward rotation start (RYn1)
signal or reverse rotation start (RYn2) signal is switched on.

Parameter No.1 setting
Forward rotation start (RYn1) ON Reverse rotation start (RYn2) ON
0 CCW rotation (address incremented) CW rotation (address decremented)
1 CW rotation (address incremented) CCW rotation (address decremented)
RYn1:ON RYn2:ON
CCW CCW
CW CW
RYn2:ON RYn1:ON
Parameter No. 1 0 Parameter No. 1 1
3) Feed length multiplication selection (parameter No.1) Set the unit multiplication factor (STM) of
position data.
Parameter No.1 setting Feed unit [μm] Position data input range [mm]
0 1 0 to 999.999
1 10 0 to 9999.99
2 100 0 to 99999.9
3 1000 0 to 999999
(c) Operation
Choosing the point table using RYnA to RYnE and turning RYn1 ON starts a motion in the
forward rotation direction over the moving distance of the position data at the preset speed and
acceleration time constant.
Turning RYn2 ON starts a motion in the reverse rotation direction according to the values set to
the selected point table.

Automatic operation mode
Automatic/manual selection (RYn6) Turn RYn6 ON.
selection
Point table No. selection 1 (RYnA)
Point table No. selection 2 (RYnB)
Point table selection Point table No. selection 3 (RYnC) Refer to section 5.2.1 (2).
Point table No. selection 4 (RYnD)
Point table No. selection 5 (RYnE)
Turn RYn1 ON to start motion in
Forward rotation start (RYn1) forward rotation direction.
Start
Reverse rotation start (RYn2) Turn RYn2 ON to start motion in
reverse rotation direction.
5 - 10
5. OPERATION
(3) Automatic operation timing chart
The timing chart is shown below.

Automatic/manual ON
selection (RYn6) OF
ON
Servo-on (RYn0) (Note 2)
OF 5ms or more
Forward rotation ON
start (RYn1) OF 8ms or more
Reverse rotation ON 5ms or more
start (RYn2) (Note 1) OF
8ms or more
Point table No. 1 2

5ms or less
Forward
rotation Point table No. 1
Servo motor speed 0r/min
Reverse Point table No. 2
rotation
In position (RXn1) ON
OF
ON
Rough match (RXn2)
OF
Movement finish ON
(RXnC) OF
Point No. output 1 2

(RX(n+2)2 to RX(n+2)6)
Ready (RXn0) ON
OF
Trouble ON
(RX(n+1)A or RY(n+3)A) OF
Note 1. Reverse rotation start (RYn2) is invalid in the absolute value command system.
2. External input signal detection delays by the input filter setting time of parameter No. 2. Also, make up a sequence
that will change the point table selection earlier by the time that takes into account the output signal sequence from
the controller and the variation of a signal change due to the hardware.
5 - 11
5. OPERATION
(4) Automatic continuous operation
POINT
This function is valid when the point table is selected using the input signal
or the remote input of CC-Link. It cannot be used when the point table No. is
selected using the remote register of CC-Link.
(a) What is automatic continuous operation?

By merely choosing one point table and making a start (RYn1 or RYn2), operation can be
performed in accordance with the point tables having consecutive numbers.
Automatic operation is available in two types: varied speed operation and automatic continuous
positioning operation.
Either type may be selected as follows.
1) In absolute value command specifying system

Point table setting
Auxiliary function
Dwell When position data is When position data is
absolute value incremental value
Automatic continuous Speed changing operation
operation Automatic continuous 0 1 3
positioning operation 1 or more 1 3
2) In incremental value command system

Point table setting
Dwell Auxiliary function
Automatic continuous Speed changing operation
operation Automatic continuous 0 1
positioning operation 1 or more 1
(b) Varied speed operation

Speed during positioning operation can be changed by setting the auxiliary function of the point
table. Use the number of point tables equal to the number of speeds to be set.
By setting "1" to the auxiliary function, operation is performed at the speed set in the next point
table during positioning. The position data valid at this time is the data selected at start and the
acceleration and deceleration time constants of the subsequent point tables are made invalid.
By setting "1" to the auxiliary function of up to point table No.30, operation can be performed at a
maximum of 31 speeds. Set "0" to the auxiliary function of the last point table.
When performing varied speed operation, always set "0" to the dwell. If "1" or more is set,
automatic continuous positioning operation is made valid.
The following table gives a setting example.
Point table No. Dwell [ms] (Note 1) Auxiliary function Variable speed operation
1 0 1
2 0 1 Consecutive point table data
3 0 0 (Note 2)
4 0 1
5 0 1
Consecutive point table data
6 0 1
7 0 0 (Note 2)
Note 1. Always set "0".
2. Always set "0" or "2" to the auxiliary function of the last point table among the consecutive point tables.
5 - 12
5. OPERATION
1) Absolute value command specifying system

This system is an auxiliary function for point tables to perform automatic operation by
specifying the absolute value command or incremental value command.
Positioning in single direction
The operation example given below assumes that the set values are as indicated in the
following table. Here, the point table No. 1 uses the absolute value command system, the point
table No. 2 the incremental value command system, the point table No. 3 the absolute value
command system, and the point table No. 4 the incremental value command system.
Point table Position data Servo motor Acceleration time constant Deceleration time constant Dwell [ms] Auxiliary
No. [ 10STM m] speed [r/min] [ms] [ms] (Note 1) function
1 5.00 3000 100 150 0 1
2 3.00 2000 Invalid Invalid 0 3
4 6.00 500 Invalid Invalid 0 2 (Note 2)
0: When point table is used in absolute value command system
2: When point table is used in incremental value command system
Acceleration time constant

Deceleration time constant
of point table No. 1 (100)
Speed
Forward Speed (1000)
Servo motor speed rotation (3000) Speed
(2000) Speed (500)
0
3.00 6.00
Position address
0 5.00 8.00 10.00 16.00
Selected point table No. 1

(RYn1) OFF
Point No. out put

1
(RX(n+2)2 to RX(n+2)6)
5 - 13
5. OPERATION
Positioning that reverses the direction midway

The operation example given below assumes that the set values are as indicated in the
following table. Here, the point table No. 1 uses the absolute value command system, the point
table No. 2 the incremental value command system, and the point table No. 3 the absolute
value system.
1 5.00 3000 100 150 0 1
0: When point table is used in absolute value command system
2: When point table is used in incremental value command system

Speed
Speed
Forward (3000)
(2000)
rotation
Servo motor speed 0
Reverse Speed (1000) Acceleration time constant
rotation
7.00
Position address
0 5.00 8.00 12.00

(RYn1)
OFF
Point No. out put

1
(RX(n+2)2 to RX(n+2)6)
5 - 14
5. OPERATION
2) Incremental value command system

The position data of the incremental value command system is the sum of the position data of
the consecutive point tables.
The operation example given below assumes that the set values are as indicated in the following
table.
1 5.00 3000 100 150 0 1
2. Always set "0" to the auxiliary function of the last point table among the consecutive point tables.

Forward Speed
Servo motor speed Speed
rotation (3000)
(2000) Speed
0 (1000)
5.00 6.00 3.00

Position address
0 5.00 11.00 14.00
(Note) ON
Forward rotation start (RYn1)
OFF
Point No. out put

(RX(n+2)2 to RX(n+2)6) 1
Note. Turning on Reverse rotation start (RYn2) starts positioning in the reverse rotation direction.
5 - 15
5. OPERATION
(c) Temporary stop/restart

When RYn7 is turned ON during automatic operation, the motor is decelerated to a temporary stop
at the deceleration time constant in the point table being executed. When RYn7 is turned ON
again, the remaining distance is executed.
If the forward/reverse rotation start signal (RYn1 or RYn2) is ignored if it is switched on during a
temporary stop.
The remaining moving distance is cleared when the operation mode is changed from the automatic
mode to the manual mode during a temporary stop.
The temporary stop/restart input is ignored during zeroing and jog operation.
1) When the servo motor is rotating
Acceleration time constant Deceleration time constant
of point table No. n of point table No. n
Servo motor speed Remaining

distance
0
Point table No. n

ON
Temporary stop/Restart (RYn7) OFF
Temporary stop (RXn7) ON
OFF
Rough match (RXn2) ON
OFF
OFF
Movement finish (RXnC) ON
OFF
Point No. out put
No. n
(RX(n+2)2 to RX(n+2)6)
2) During dwell
Point table No. n Point table No. n 1
Dwell ta tb
ta tb
Servo motor speed
0
Point table No. n

ON
Temporary stop/Restart (RYn7) OFF
ON
Temporary stop (RXn7)
OFF
ON
Rough match (RXn2)
OFF
OFF
ON
OFF
Point No. out put
No. n
(RX(n+2)2 to RX(n+2)6)
5 - 16
5. OPERATION
5.2.3 Remote register-based position/speed setting
This operation can be used when 2 stations are occupied. This section explains operation to be performed
when the remote register is used to specify the position command data/speed command data.
(1) Absolute value command positioning in absolute value command system

The position data set in the absolute value command system are used as absolute values in
positioning. Set the input signals and parameters as indicated below.
Item Used device/parameter Description

Automatic operation mode Automatic/manual selection (RYn6) Turn RYn6 ON.
Remote register-based position/speed Position/speed specifying system selection
Turn RY(n+2)A ON.
setting (RY(n+2)A)
0 : Absolute value command
Command system Parameter No.0
system is selected.
2 : Remote register-based
Remote register-based position/speed
Parameter No.41 position/speed specifying
system is selected.
Position command data lower 16 bit Set the lower 16 bits of position
(RWwn+4) data to RWwn+4, and the upper 16
Position data
Position command data upper 16 bit bits to RWwn+5.
(RWwn+5) Setting range: 999999 to 999999
Servo motor speed Speed command data (RWwn+6) Set the servo motor speed.
Set the position data to RWwn+4/RWwn+5, and the speed command data to RWwn+6, and store them
into the servo amplifier.
In the absolute value command system, Absolute value/incremental value selection (RY(n+2)B) can be
used to select whether the values set to the position data are absolute values or incremental values.
The position data set to RWwn+4/RWwn+5 are handled as absolute values when RY(n+2)B is turned
OFF or as incremental values when it is turned ON. During operation, how the position data will be
handled (absolute values or incremental values) depends on the status of RY(n+2)B when Forward
rotation start (RYn1) is turned ON.
Here, RY(n+2)B is turned OFF since the position data are handled as absolute values.
5 - 17
5. OPERATION
Automatic/manual selection ON
(RYn6) OFF
ON
Servo-on (RYn0)
OFF
Position/speed specifying ON
system selection (RY(n+2)A) OFF
Incremental value/absolute ON
value selection (RY(n+2)B) OFF
(Note 1) (Note 1)
ON 5ms or more 5ms or more
OFF
8ms or more 8ms or more
Position data
Position data 1 Position data 2
(RWwn+4 RWwn+5)
Speed data (RWwn+6) Speed data 1 Speed data 2

(Note 2)
Position instruction execution ON
demand (RY(n+2)0) OFF
(Note 2)
Speed instruction execution ON
5ms or less
Forward Absolute value

rotation data 1
Reverse Absolute value
rotation data 2
ON
In position speed (RXn1)
OFF
ON
Rough match (RXn2)
OFF
ON
OFF
ON
Ready (RXn0)
OFF
Trouble (RX(n+1)A or ON
RX(n+3)A) OFF
Note 1. An external input signal is detected after a delay of the input filter setting time in parameter No. 2. Also, configure a sequence
that will change Point table selection earlier with consideration given to the output signal sequence from the controller and the
variations of signal changes due to the hardware.
2. For details of the operation timing of RY(n 2)0 and RY(N 2)1, refer to the section 3.6.3 (3).
5 - 18
5. OPERATION
(2) Incremental value command positioning in absolute value command system

The position data set in the absolute value command system are used as incremental values in
positioning. Set the input signals and parameters as indicated below.

Turn RY(n+2)A ON.
setting (RY(n+2)A)
0 : Absolute value command
Command system Parameter No.0
system is selected.
system is selected.
Position data
Here, Absolute value/incremental value selection RY(n+2)B is turned ON since the position data are
handled as incremental values.
5 - 19
5. OPERATION
(RYn6) OFF
ON
Servo-on (RYn0)
OFF
Incremental value/absolute ON
value selection (RY(n+2)B) OFF
(Note 1) (Note 1)
ON 5ms or more 5ms or more
OFF
8ms or more 8ms or more
Position data Position data 1 Position data 2
(RWwn+4 RWwn+5)

(Note 2)
(Note 2)
5ms or less

rotation data 1
rotation data 2
ON
OFF
ON
Rough match (RXn2)
OFF
ON
OFF
ON
Ready (RXn0)
OFF
RX(n+3)A) OFF
Note 1. An external input signal is detected after a delay of the input filter setting time in parameter No. 2. Also, configure a sequence
that will change Point table selection earlier with consideration given to the output signal sequence from the controller and the
variations of signal changes due to the hardware.
5 - 20
5. OPERATION
(3) Positioning in incremental value command system

Execute positioning in the incremental value command system. Set the input signals and parameters
as indicated below.

Turn RY(n+2)A ON.
setting (RY(n+2)A)
1 : Incremental value
Command system Parameter No.0 command system is
selected.
system is selected.
Position data
Set " 1 " in parameter No. 0 to select the incremental value command system. In the incremental
value command system, the position data are handled as incremental values. Hence, Absolute
value/incremental value selection (RY(n+2)B) is invalid.
5 - 21
5. OPERATION
(RYn6) OFF
ON
Servo-on (RYn0)
OFF
(Note 1)
ON 5ms or more
OFF
8ms or more (Note 1)
ON 5ms or more
Reverse rotation start (RYn2)
OFF
8ms or more
Position data Position data 1 Position data 2
(RWwn+4 RWwn+5)

(Note 2)
(Note 2)
5ms or less

rotation data 1
rotation data 2
ON
OFF
ON
Rough match (RXn2)
OFF
ON
OFF
ON
Ready (RXn0)
OFF
RX(n+3)A) OFF
Note 1. An external input signal is detected after a delay of the input filter setting time in parameter No. PD19. Also, configure a
sequence that will change Point table selection earlier with consideration given to the output signal sequence from the controller
and the variations of signal changes due to the hardware.
5 - 22
5. OPERATION
5.3 Manual operation mode
For machine adjustment, home position matching, etc., jog operation may be used to make a motion to
any position.
(1) Setting
Set the input signal and parameters as follows according to the purpose of use. In this case, the point
table No. selection 1 to 5 (RYnA to RYnE) are invalid.

Manual operation mode selection Automatic/manual selection (RYn6) Turn RYn6 OFF.
Servo motor rotation direction Parameter No.1 Refer to (2) in this section.
Jog speed Parameter No.13 Set the speed of the servo motor.
Use the acceleration/deceleration
Acceleration/deceleration time constant Point table No.1
time constants in point table No.1.
(2) Servo motor rotation direction

Parameter No. 1 setting
Forward rotation start (RYn1) ON Reverse rotation start (RYn2) ON
0 CCW rotation CW rotation
1 CW rotation CCW rotation
RYn1:ON RYn2:ON
CCW CCW
CW CW
RYn2:ON RYn1:ON
Parameter No. 1 0 Parameter No. 1 1
(3) Operation
By turning RYn1 ON, operation is performed under the conditions of the jog speed set in the
parameter and the acceleration and deceleration time constants in set point table No.1. For the
rotation direction, refer to (2) in this section. By turning RYn2 ON, the servo motor rotates in the
reverse direction to forward rotation start (RYn1).
5 - 23
5. OPERATION
(4) Timing chart

ON
Servo-on (RYn0)
OFF
ON 80ms
Ready (RXn0)
OFF
Trouble ON
(RX(n+1)A or RX(n+3)A) OFF
Automatic/manual ON
mode selection (RYn6) OFF
Movement finish ON
(RXnC) OFF
ON
Rough match (RXn2) OFF
Forward
rotation
Reverse
rotation
ON
Forward rotation start Forward rotation jog
OFF
(RYn1)
ON
Reverse rotation start Reverse rotation jog
OFF
(RYn2)
5 - 24
5. OPERATION
5.4 Manual home position return mode
5.4.1 Outline of home position return
Home position return is performed to match the command coordinates with the machine coordinates. In
the incremental system, home position return is required every time input power is switched on. In the
absolute position detection system, once home position return is done at the time of installation, the
current position is retained if power is switched off. Hence, home position return is not required when
power is switched on again.
This servo amplifier has the home position return methods given in this section. Choose the most
appropriate method for your machine structure and application.
This servo amplifier has the home position return automatic return function which executes home
position return by making an automatic return to a proper position if the machine has stopped beyond or
at the proximity dog. Manual motion by jog operation or the like is not required.
(1) Manual home position return types

Choose the optimum home position return according to the machine type, etc.
Type Home position return method Features

General home position return method using a
With deceleration started at the front end of a proximity dog.
proximity dog, the position where the first Repeatability of home position return is
Dog type home position Z-phase signal is given past the rear end of the dog excellent.
return or a motion has been made over the home position The machine is less burdened.
shift distance starting from the Z-phase signal is Used when the width of the proximity dog
defined as a home position.(Note) can be set greater than the deceleration
distance of the servo motor.
With deceleration started at the front end of a Home position return method using a
proximity dog, the position where the first Z-phase proximity dog.
signal is given after advancement over the preset Used when it is desired to minimize the
Count type home
moving distance after the proximity dog or a motion length of the proximity dog.
position return
has been made over the home position shift distance
starting from the Z-phase signal is defined as a
home position.
Data setting type home
An arbitrary position is defined as a home position. No proximity dog required.
position return
Since the machine part collides with the
The position where the machine stops when its part
Stopper type home machine be fully lowered.
is pressed against a machine stopper is defined as a
position return The machine and stopper strength must be
home position.
increased.
Home position ignorance
The position where servo is switched on is defined as
(Servo-on position as
a home position.
home position)
The position where the axis, which had started The Z-phase signal is not needed.
decelerating at the front end of a proximity dog, has
Dog type rear end
moved the after-proximity dog moving distance and
reference
home position shift distance after it passed the rear
end is defined as a home position.
The position where the axis, which had started The Z-phase signal is not needed.
decelerating at the front end of a proximity dog, has
Count type front end
moved the after-proximity dog moving distance and
reference
home position shift distance is defined as a home
position.
The position where the first Z-phase signal is issued
Dog cradle type after detection of the proximity dog front end is
defined as a home position.
Note. The Z-phase signal is a signal recognized in the servo amplifier once per servo motor revolution and cannot be used as an output
signal.
5 - 25
5. OPERATION
(2) Home position return parameter

When performing home position return, set parameter No.8 as follows.
Parameter No. 8
0
Home position return method························································1)
0: Dog type
1: Count type
2: Data setting type
3: Stopper type
4: Home position ignorance (Servo-on position as home position)
5: Dog type rear end reference
6: Count type front end reference
7: Dog cradle type
Home position return direction ······················································2)
0: Address increment direction
1: Address decrement direction
Proximity dog input polarity ···························································3)

0: OFF indicates detection of the dog.
1: ON indicates detection of the dog.
1) Choose the home position return method.
2) Choose the starting direction of home position return. Set "0" to start home position return in
the direction in which the address is incremented from the current position, or "1" to start home
position return in the direction in which the address is decremented.
3) Choose the polarity at which the proximity dog is detected. Set "0" to detect the dog when the
proximity dog device (RYn3) is OFF, or "1" to detect the dog when the device is ON.
(3) Instructions
1) Before starting home position return, always make sure that the limit switch operates.
2) Confirm the home position return direction. Incorrect setting will cause the machine to run
reversely.
3) Confirm the proximity dog input polarity. Otherwise, misoperation can occur.
5 - 26
5. OPERATION
5.4.2 Dog type home position return
A home position return method using a proximity dog. With deceleration started at the front end of the
proximity dog, the position where the first Z-phase signal is given past the rear end of the dog or a motion
has been made over the home position shift distance starting from the Z-phase signal is defined as a home
position.
(1) Signals, parameters

Set the input signals and parameters as follows.
Item Device/Parameter used Description

Point table No. selection 1 (RYnA) Turn RYnA OFF.
Manual home position return Point table No. selection 2 (RYnB) Turn RYnB OFF.
mode selection Point table No. selection 3 (RYnC) Turn RYnC OFF.
Point table No. selection 4 (RYnD) Turn RYnD OFF.
Point table No. selection 5 (RYnE) Turn RYnE OFF.
Remote register-based Position/speed specifying system selection
Turn RY(n+2)A OFF.
position/speed setting (RY(n+2)A)
0 :Dog type home position return is
Dog type home position return Parameter No.8
selected.
Refer to section 5.4.1 (2) and choose home
Home position return direction Parameter No.8
position return direction.
Refer to section 5.4.1 (2) and choose dog
Dog input polarity Parameter No.8
input polarity.
Home position return speed Parameter No.9 Set speed until detection of dog.
Creep speed Parameter No.10 Set speed after detection of dog.
Set when shifting the home position
Home position shift distance Parameter No.11 starting at the first Z-phase signal after
passage of proximity dog rear end.
Use the acceleration/deceleration time
acceleration/deceleration time Point table No.1
constants of point table No.1.
constants
Home position return position Set the current position at home position
Parameter No.42
data return completion.
(2) Length of proximity dog

To ensure that the Z-phase signal of the servo motor is generated during detection of the proximity
dog (RYn3), the proximity dog should have the length which satisfies formulas (5.2) and (5.3).
V td .............................................................................. (5.2)
L1
60 2
L1 : Proximity dog length [mm]

V : Home position return speed [mm/min]
td : Deceleration time [s]
L2 2 S ................................................................................... (5.3)
L2 : Proximity dog length [mm]

S : Moving distance per servo motor revolution [mm]
5 - 27
5. OPERATION
(3) Timing chart

ON
OFF
ON
Rough match (RXn2)
OFF
Home position return ON
completion (RXn3) OFF Home position shift
Home position return Point table No. 1
Point table No. 1 distance Parameter No. 11
speed Parameter No. 9 Deceleration time constant
Acceleration time Creep speed
constant Home position
Parameter No. 10
Servo motor speed td

5ms or less
Proximity dog Home position address
Parameter No. 42
ON
Z-phase
OFF
ON
Proximity dog (RYn3)
OFF
ON 8ms or more
OFF
ON
OFF
The parameter No.42 (home position return position data) setting value is the positioning address
after the home position return is completed.
(4) Adjustment
In dog type home position return, adjust to ensure that the Z-phase signal is generated during dog
detection. Locate the rear end of the proximity dog (RYn3) at approximately the center of two
consecutive Z-phase signals.
The position where the Z-phase signal is generated can be monitored in "Within one-revolution
position" of "Status display".
0 65536 0
Servo motor Z-phase

Proximity
dog
Proximity dog ON
(RYn3) OF
5 - 28
5. OPERATION
5.4.3 Count type home position return
In count type home position return, a motion is made over the distance set in parameter No.43 (moving
distance after proximity dog) after detection of the proximity dog front end. The position where the first Z-
phase signal is given after that is defined as a home position. Hence, if the proximity dog (RYn3) is 10ms
or longer, there is no restriction on the dog length. This home position return method is used when the
required proximity dog length cannot be reserved to use dog type home position return or when the
proximity dog (RYn3) is entered electrically from a controller or the like.


Manual home position return Point table No. selection 2 (RYnB) Turn RYnB OFF.
mode selection Point table No. selection 3 (RYnC) Turn RYnC OFF.
Turn RY(n+2)A OFF.
1: Count type home position return
Count type home position return Parameter No.8
is selected.
Refer to section 5.4.1 (2) and choose home
position return direction.
Refer to section 5.4.1 (2) and choose dog
input polarity.
Home position return speed Parameter No.9 Set speed until detection of dog.
Creep speed Parameter No.10 Set speed after detection of dog.
Set when shifting the home position,
starting at the first Z-phase signal given
Home position shift distance Parameter No.11
after passage of the proximity dog front end
and movement over the moving distance.
Moving distance after proximity Set the moving distance after passage of
Parameter No.43
dog proximity dog front end.
constants of point table No.1.
constants
Parameter No.42
5 - 29
5. OPERATION
(2) Timing chart

ON
OFF
Rough match ON
(RXn2) OFF
completion (RXn3) OFF Home position
Home position return Point table No. 1 shift distance
Point table No. 1 Deceleration time
Acceleration time constant speed Parameter No. 9 constant
Parameter No. 11
Creep speed Home position
Parameter No. 10
Servo motor speed

5ms or less
Moving distance after Proximity dog Home position address
proximity dog Parameter No. 42
Parameter No. 43
Z-phase ON
OFF
Proximity dog (RYn3) ON
OFF
Forward rotation ON 8ms or more
start (RYn1) OFF
Reverse rotation ON
start (RYn2) OFF
5 - 30
5. OPERATION
5.4.4 Data setting type home position return
Data setting type home position return is used when it is desired to determine any position as a home
position. JOG operation can be used for movement.


Manual home position return mode Point table No. selection 2 (RYnB) Turn RYnB OFF.
selection Point table No. selection 3 (RYnC) Turn RYnC OFF.
Turn RY(n+2)A OFF.
setting (RY(n+2)A)
2: Data setting type home
Data setting type home position return Parameter No.8
position return is selected.
Set the current position at home
Home position return position data Parameter No.42
position return completion.
(2) Timing chart

Automatic/manual ON
selection (RYn6) OFF
ON
OFF
Rough match ON
(RXn2) OFF
Home position ON
return completion OFF
(RXn3)
Home position address

Parameter No. 42
Servo motor speed
5ms or less

start (RYn1) OFF
Reverse rotation ON
start (RYn2) OFF
Movement to the home position Operation for home position return
5 - 31
5. OPERATION
5.4.5 Stopper type home position return
In stopper type home position return, a machine part is pressed against a stopper or the like by jog
operation to make a home position return and that position is defined as a home position.


Manual home position Point table No. selection 2 (RYnB) Turn RYnB OFF.
return mode selection Point table No. selection 3 (RYnC) Turn RYnC OFF.
Turn RY(n+2)A OFF.
Stopper type home position 3: Stopper type home position return is
Parameter No.8
return selected.
Home position return Refer to section 5.4.1 (2) and choose the home
Parameter No.8
direction position return direction.
Home position return speed Parameter No.9 Set the speed till contact with the stopper.
Time from when the part makes contact with
the stopper to when home position return data
Stopper time Parameter No.44
is obtained to output home position return
completion (RXn3)
Stopper type home position Set the servo motor torque limit value for
Parameter No.45
return torque limit execution of stopper type home position return.
Home position return Use the acceleration time constant of point
Point table No.1
acceleration time constant table No.1.
Home position return Set the current position at home position
Parameter No.42
position data return completion.
5 - 32
5. OPERATION
(2) Timing chart
Automatic/manual ON
Movement finish ON
(RXnC) OFF
Rough match ON
(RXn2) OFF
Home position retum ON
completion (RXn3) OFF
Point table No.1
Acceleration time constant Home position address
speed Parameter No.9
Parameter No.42
Servo motor speed
5ms or less Stopper

start (RYn1) OFF
Reverse rotation ON
start (RYn2) OFF
Stopper time
Limiting torque ON Parameter No.44
(RXn4) OFF
Torque limit value Parameter No.28 (Note) Parameter 45 Parameter No.28
Note. The torque limit that is enabled at this point is as follows.
(Note)
Internal torque limit Torque limit to be
Limit value status
selection enabled
(RY(N 2)6)
0 Parameter No.45
Parameter No.29 Parameter No.45 Parameter No.45
1
Parameter No.29 Parameter No.45 Parameter No.29
Note. 0: OFF
1: ON
5 - 33
5. OPERATION
5.4.6 Home position ignorance (servo-on position defined as home position)
The position where servo is switched on is defined as a home position.
(1) Signals, parameter

Set the input signals and parameter as follows.

Home position ignorance Parameter No.8 4: Home position ignorance is selected.
Parameter No.42
(2) Timing chart

Servo-on (RYn0) ON
OFF
ON
Ready (RXn0)
OFF
Automatic/manual
selection (RYn6) ON
OFF
Movement finish (RXnC) ON

OFF
Rough match ON
(RXn2) OFF
Home position ON
return completion OFF
(RXn3)

Parameter No. 42
Servo motor speed
5 - 34
5. OPERATION
5.4.7 Dog type rear end reference home position return
POINT
This home position return method depends on the timing of reading
Proximity dog (RYn3) that has detected the rear end of a proximity dog.
Hence, if a home position return is made at the creep speed of 100r/min, an
error of 200 pulses will occur in the home position. The error of the home
position is larger as the creep speed is higher.
The position where the axis, which had started decelerating at the front end of a proximity dog, has
moved the after-proximity dog moving distance and home position shift distance after it passed the rear
end is defined as a home position. A home position return that does not depend on the Z-phase signal can
be made.

Set the input signals and parameters as indicated below.

Turn RY(n+2)A OFF.
Dog type rear end reference home 5: Select the dog type rear end
Parameter No.8
position return reference.
Refer to section 5.4.1 (2) and select the
home position return direction.
dog input polarity.
Home position return speed Parameter No.9 Set the speed till the dog is detected.
Creep speed Parameter No.10 Set the speed after the dog is detected.
Set when the home position is moved
Home position shift distance Parameter No.11 from where the axis has passed the
proximity dog rear end.
Set the moving distance after the axis
Moving distance after proximity dog Parameter No.43
has passed the proximity dog rear end.
Home position return acceleration/ Use the acceleration/deceleration time
Point table No.1
deceleration time constants constant of point table No. 1.
5 - 35
5. OPERATION
(2) Timing chart

Automatic/manual ON
ON
OFF
ON
Rough match (RXn2)
OFF
Moving distance after proximity dog
Home position return speed
Home position shift distance
Creep speed
Servo motor speed

5ms or less
Proximity dog Parameter No. 42
ON
OFF
ON
OFF
8ms or more
ON
OFF
5 - 36
5. OPERATION
5.4.8 Count type front end reference home position return
POINT
This home position return method depends on the timing of reading
Proximity dog (RYn3) that has detected the front end of a proximity dog.
Hence, if a home position return is made at the home position return speed of
100r/min, an error of 200 pulses will occur in the home position. The error of
the home position is larger as the home position return speed is higher.
The position where the axis, which had started decelerating at the front end of a proximity dog, has
moved the after-proximity dog moving distance and home position shift distance is defined as a home
position. A home position return that does not depend on the Z-phase signal can be made. The home
position may change if the home position return speed varies.


Turn RY(n+2)A OFF.
Count type dog front end reference 6: Select the count type dog front
Parameter No.8
home position return end reference.
dog input polarity.
Home position shift distance Parameter No.11 from where the axis has passed the
proximity dog rear end.
Set the moving distance after the axis
Moving distance after proximity dog Parameter No.43
has passed the proximity dog rear end.
Home position return acceleration/ Use the acceleration/deceleration time
Point table No.1
deceleration time constants constant of point table No. 1.
5 - 37
5. OPERATION
(2) Timing chart

Automatic/manual ON
ON
OFF
ON
Rough match (RXn2)
OFF
Moving distance after proximity dog
Home position return speed Home position shift distance
Creep speed
Servo motor speed

5ms or less
Proximity dog (DOG) Parameter No. 42
ON
Proximity dog (RXn3)
OFF
Forward rotation ON
start (RYn1) OFF
8ms or more
Reverse rotation ON
start (RYn2) OFF
5 - 38
5. OPERATION
5.4.9 Dog cradle type home position return
The position where the first Z-phase signal is issued after detection of the proximity dog front end can be
defined as a home position.


Turn RY(n+2)A OFF.
Dog cradle type home position
Parameter No.8 7: Select the dog cradle type.
return
dog input polarity.
Home position shift distance Parameter No.11
from the Z-phase signal position.
constant of point table No. 1.
constants
5 - 39
5. OPERATION
(2) Timing chart

Automatic/manual ON
ON
OFF
ON
Rough match (RXn2)
OFF
Home position return speed Home position shift distance
Creep speed
Servo motor speed

5ms or less
Proximity dog Parameter No. 42
ON
Z-phase
OFF
ON
OFF
Forward rotation ON
start (RYn1) OFF
8ms or more
Reverse rotation ON
start (RYn2) OFF
5 - 40
5. OPERATION
5.4.10 Home position return automatic return function
If the current position is at or beyond the proximity dog in dog or count type home position return, you
need not make a start after making a return by jog operation or the like.
When the current position is at the proximity dog, an automatic return is made before home position
return.
Home position return direction Proximity dog
Home position

start position
At a start, a motion is made in the home position return direction and an automatic return is made on
detection of the limit switch. The motion stops past the front end of the proximity dog, and home position
return is resumed at that position. If the proximity dog cannot be detected, the motion stops on detection
of the opposite limit switch and AL. 90 occurs.
Limit switch
Home position return direction Proximity dog Limit LS
Home
position

start position
Software limit cannot be used with these functions.
5 - 41
5. OPERATION
5.4.11 Automatic positioning function to the home position
POINT
You cannot perform automatic positioning from outside the position data
setting range to the home position. In this case, make a home position return
again using a manual home position return.
If this function is used when returning to the home position again after performing a manual home
position return after a power-on and deciding the home position, automatic positioning can be carried out
to the home position at high speed. In an absolute position system, manual home position return is not
required after power-on.
Please perform a manual home position return beforehand after a power-on.
Set the input signals and parameter as follows.

Automatic/manual selection (RYn6) Short MD0 ON.
Point table No. selection 1 (RYnA) Open DI0 OFF.
Manual home position return mode Point table No. selection 2 (RYnB) Open DI1 OFF.
Home position return speed Parameter No.9 Speed is set up.
Home position return acceleration Use the acceleration time constant of point table
Point table No.1
time constant No.1.
Set up the home position return speed of the automatic positioning function to the home position by
parameter No.9. Use the data of point table No.1 to set the acceleration time constant and deceleration
time constant. When reverse rotation start (RYn2) is ON, it will position automatically at the home
position.
Home position return speed Deceleration time constant
Parameter No. 9 of point table No. 1
of point table No. 1
Servo motor speed
Home position

OFF
Reverse rotation start (RYn2) ON

OFF
5 - 42
5. OPERATION
5.5 Absolute position detection system
If an absolute position erase alarm (AL.25) or an absolute position counter warning

CAUTION (AL.E3) has occurred, always perform home position setting again. Not doing so
can cause runaway.
POINT
When the following parameters are changed, the home position is lost when
turning on the power after the change. Execute the home position return
again when turning on the power.
First digit of parameter No.1 (ST1 coordinate system selection)
Parameter No. 4 (Electronic gear numerator)
Parameter No. 5 (Electronic gear denominator)
Parameter No. 42 (Home position return position data)
This servo amplifier contains a single-axis controller. Also, all servo motor encoders are compatible with
an absolute position system. Hence, an absolute position detection system can be configured up by merely
loading an absolute position data back-up battery and setting parameter values.
(1) Restrictions
An absolute position detection system cannot be built under the following conditions.
1) Stroke-less coordinate system, e.g. rotary shaft, infinite positioning.
2) Operation performed in incremental value command type positioning system.
(2) Specifications
Item Description
System Electronic battery backup system
1 piece of lithium battery ( primary battery, nominal 3.6V)
Battery
Type: MR-BAT or A6BAT
Maximum revolution range Home position 32767 rev.
(Note 1) Maximum speed at power failure 500r/min
(Note 2) Battery backup time Approx. 10,000 hours (battery life with power off)
(Note 3) Data holding time during battery
2 hours at delivery, 1 hour in 5 years after delivery
replacement
Battery storage period 5 years from date of manufacture
Note 1. Maximum speed available when the shaft is rotated by external force at the time of power failure or the like.
2. Time to hold data by a battery with power off. It is recommended to replace the battery in three years independently of
whether power is kept on or off.
3. Period during which data can be held by the super capacitor in the encoder after power-off, with the battery voltage low or
the battery removed, or during which data can be held with the encoder cable disconnected.
Battery replacement should be finished within this period.
5 - 43
5. OPERATION
(3) Structure
Component Description
Servo amplifier
Use standard models.
Servo motor
Battery MR-BAT or A6BAT
Use a standard model.
Encoder cable
When fabricating, refer to section 15.1.4.
(4) Outline of absolute position detection data communication

For normal operation, as shown below, the encoder consists of a detector designed to detect a position
within one revolution and a cumulative revolution counter designed to detect the number of
revolutions.
The absolute position detection system always detects the absolute position of the machine and keeps
it battery-backed, independently of whether the general-purpose programming controller power is on
or off. Therefore, once the home position is defined at the time of machine installation, home position
return is not needed when power is switched on thereafter.
If a power failure or a fault occurs, restoration is easy.
Also, the absolute position data, which is battery-backed by the super capacitor in the encoder, can be
retained within the specified period (cumulative revolution counter value retaining time) if the cable is
unplugged or broken.
Servo amplifier
Point table No. selection
Position control
data
Speed control
I/O circuit EEP-ROM memory
(RYnA to RYnE), etc. LSO Current position
1XO
Position data, speed data Backup at
power off 1X
(current position read) LS
Detection of position
Speed detection
within one revolution
Battery MR-BAT
Servo motor
1 pulse/rev. Cumulative
revolution counter High-speed serial
Super capacitor communication
Within one-revolution counter
(5) Battery installation procedure
Before installing a battery, turn off the main circuit power while keeping the control
circuit power on. Wait for 15 minutes or more until the charge lamp turns off. Then,
WARNING confirm that the voltage between P and N is safe with a voltage tester and others.
Otherwise, an electric shock may occur. In addition, always confirm from the front
of the servo amplifier whether the charge lamp is off or not.
POINT
The internal circuits of the servo amplifier may be damaged by static electricity.
Always take the following precautions.
Ground human body and work bench.
Do not touch the conductive areas, such as connector pins and electrical
parts, directly by hand.
5 - 44
5. OPERATION
1) Open the operation window. (When the model used is the MR-J2S-200CP-S084 MR-J2S-
350CP-S084 or more, also remove the front cover.)
2) Install the battery in the battery holder.
3) Install the battery connector into CON1 until it clicks.

Battery connector
Operation window Battery connector
CON1
CON1
Battery
Battery Battery holder Battery holder
For MR-J2S-100CP-S084 or less For MR-J2S-200CP-S084 MR-J2S-350CP-S084
Battery connector
CON1
Battery holder Battery
For MR-J2S-500CP-S084 MR-J2S-700CP-S084
(6) Parameter setting

Set parameter No.2 (Function selection 1) as indicated below to make the absolute position detection
system valid.
Parameter No.2
1
Selection of absolute position detection system

0: Incremental system
1: Absolute position detection system
5 - 45
5. OPERATION
MEMO
5 - 46
6. PARAMETERS
6. PARAMETERS
Never adjust or change the parameter values extremely as it will make operation
CAUTION instable.
6.1 Parameter list
6.1.1 Parameter write inhibit
POINT
Set "000E" when using the MR Configurator (Servo Configuration
Software) to make device setting.
After setting the parameter No.19 value, switch power off, then on to
make that setting valid.
In the servo amplifier, its parameters are classified into the basic parameters (No.0 to 19), expansion
parameters 1 (No.20 to 53), expansion parameters 2 (No.54 to 77), special parameters 1 (No.78 to 90)
special parameters 2 (No. 91 to 99) and option unit parameters (No. 100 to 124) according to their safety
aspects and frequencies of use. In the factory setting condition, the customer can change the basic
parameter values but cannot change the expansion parameter 1 2 values and special parameter 1 2
values. When fine adjustment, e.g. gain adjustment, is required, change the parameter No.19 setting to
make the expansion parameters write-enabled.
The following table lists the parameters whose values are made valid for reference/write by setting
parameter No. 19. Operation can be performed for the parameters marked .
Basic Expansion Expansion Special Special Option unit

Parameter
Operation parameters parameters 1 parameters 2 parameter 1 parameter 2 parameter
No.19 setting
No.0 to No.19 No.20 to No.53 No.54 to No.77 No.78 to No.90 No.91 to No.99 No.100 to 124
0000 Reference
(initial value) Write
Reference No.19 only
000A
Write No.19 only
Reference
000B
Write
Reference
000C
Write
Reference
000E
Write
Reference
000F
Write
Reference
000AB
Write
6- 1
6. PARAMETERS
6.1.2 List
POINT
The parameters marked * before their symbols are made valid by
switching power off once and then switching it on again after parameter
setting.
Refer to the corresponding reference items for details of the parameters.
(1) Item list

Customer
Class No. Symbol Name and Function Initial value Unit
setting
0 *STY Command system, regenerative option selection 0000
1 *FTY Feeding function selection 0000
2 *OP1 Function selection 1 0002
3 ATU Auto tuning 0105
4 *CMX Electronic gear numerator 1
5 *CDV Electronic gear denominator 1
6 INP In-position range 100 m
7 PG1 Position control gain 1 35 rad/s
Basic parameters
8 ZTY Home position return type 0010

9 ZRF Home position return speed 500 r/min
10 CRF Creep speed 10 r/min
11 ZST Home position shift distance 0 m
12 CRP Rough match output range 0 10STM m
13 JOG Jog speed 100 r/min
14 *STC S-pattern acceleration/deceleration time constant 0 ms
15 *SNO Station number setting 0 station
16 *BPS Communication baud rate selection, alarm history clear 0000
17 For manufacturer setting 0100
18 *DMD Status display selection 0000
19 *BLK Parameter write inhibit 0000
6- 2
6. PARAMETERS
Customer
setting
22 OP4 Function selection 4 0000
24 FFC Feed forward gain 0 %
25 0
27 4000
28 TL1 Internal torque limit 1 100 %
29 TL2 Internal torque limit 2 100 %
30 *BKC Backlash compensation 0 pulse
31 0
For manufacturer setting
32 0
33 MBR Electromagnetic brake sequence output 100 ms
Expansion parameters 1
34 GD2 Ratio of load inertia moment to Servo motor inertia moment 70 0.1 times
36 VG1 Speed control gain 1 177 rad/s
38 VIC Speed integral compensation 48 ms
39 VDC Speed differential compensation 980
41 *DSS Remote register-based position/speed specifying system selection 0000
42 *ZSP Home position return position data 0 10STM m
43 DCT Moving distance after proximity dog 1000 10STM m
44 ZTM Stopper type home position return stopper time 100 ms
45 ZTT Stopper type home position return torque limit value 30 %
46
LMP Software limit 0 10STM m
47
48
LMN Software limit 0 10STM m
49
50
*LPP Position range output address 0 10STM m
51
52
*LNP Position range output address 0 10STM m
53
6- 3
6. PARAMETERS
Customer
setting
58 0000
60 0000
61 NH1 Machine resonance suppression filter 1 0000
62 NH2 Machine resonance suppression filter 2 0000
63 LPF Low-pass filter, adaptive vibration suppression control 0000

64 GD2B Ratio of load inertia moment to servo motor inertia moment 2 70 0.1 times
65 PG2B Position control gain 2 changing ratio 100 %
66 VG2B Speed control gain 2 changing ratio 100 %
67 VICB Speed integral compensation changing ratio 100 %
68 *CDP Gain changing selection 0000
69 CDS Gain changing condition 10 (Note)
70 CDT Gain changing time constant 1 ms
71 100
72 10000
73 10
75 100
76 100
77 100
78 *DI0 I/O device selection 0000
79 *DI1 Input device selection 1 0000
Special parameters 1

88 *DO1 Output device selection 1 0005
89 *DO2 Output device selection 2 0D04
90 *DO3 Output device selection 3 0102
91 0000
92 0000
93 400
94 100
96 1
97 0
98 50
99 0000
Note. Depends on the parameter No. 68 setting.
6- 4
6. PARAMETERS
Customer
setting
100 0000
101 0000
102 0000
103 0000
104 1
105 1
106 0
107 0
108 0
109 0
Option unit parameter
110 0
111 0
112 0
113 0
114 0
115 0001
116 *IN1 External I/O function selection 1 0230
119 0
120 0
121 0
122 0
123 0
124 0
6- 5
6. PARAMETERS
(2) Detail list
Initial Setting
Class No. Symbol Name and Function Unit
value range
0 *STY Command system, regenerative option selection 0000 Refer to
Used to select the command system and regenerative option. Name
and
0 0
function
Selection of command system column.
0: Absolute value command system
1: Incremental value command system
Selection of regenerative option

(Refer to section 15.1.1)
0: Not used (The built-in regenerative resistor is used.
However, the MR-J2S-10CP-S084 does not have a built-in
regenerative resistor and therefore cannot use it.)
1: FR-RC, FR-BU2
2:MR-RB032
3:MR-RB12
4:MR-RB32
5:MR-RB30
6:MR-RB50 (Cooling fan is required)
8:MR-RB31
9:MR-RB51 (Cooling fan is required)
Select the regenerative option that is compatible with the
servo amplifier.
Selection of an incompatible option will result in a parameter
error.
Basic parameters
1 *FTY Feeding function selection 0000 Refer to

Used to set the forward rotation start coordinate system and feed length Name
multiplying factor.
and
0 function
column.
Forward rotation start coordinate system selection
(Refer to section 5.2.2 to 5.2.4)
0: Address is incremented in CCW direction
1: Address is incremented in CW direction
Feed length multiplication factor (STM)

(Refer to section 5.2.2 to 5.2.4)
0: 1 time
1: 10 times
2: 100 times
3: 1000 times
Servo-on (RYn0) -off, forced stop (EMG) -off

follow-up for absolute value command
in incremental system
0: Invalid
1: Valid
Normally, when this servo amplifier is used
in the absolute value command method of the
incremental system, placing it in a servo off or
forced stop status will erase the home position.
When "1" is set in this parameter, the home
position will not be erased if the servo amplifier
is placed in a servo off or forced stop status.
Operation can be resumed when servo-on (SON)
is turned on again or forced stop (EMG) is canceled.
6- 6
6. PARAMETERS
Initial Setting
value range
2 *OP1 Function selection 1 0002 Refer to
Used to select the input filter and absolute position detection system. Name
and
0 0
function
Input filter column.
If external input signal causes chattering due
to noise, etc., input filter is used to suppress it.
0: None
1: 0.88[ms]
2: 1.77[ms]
3: 2.66[ms]
4: 3.55[ms]
5: 4.44[ms]
Selection of absolute position detection system
0: Incremental system
1: Absolute position detection system
3 ATU Auto tuning 0105 Refer to

Used to selection the response level, etc. for execution of auto tuning.
(Refer to chapter 9) Name
and
0 0 function
Auto tuning response level setting column.
Set Response Machine resonance

value level frequency guideline
1 Low 15Hz
Basic parameters
2 response 20Hz
3 25Hz
4 30Hz
5 35Hz
6 45Hz
7 55Hz
Middle
8 70Hz
response
9 85Hz
A 105Hz
B 130Hz
C 160Hz
D 200Hz
E High 240Hz
F response 300Hz
If the machine hunts or generates large gear sound,
decrease the set value.
To improve performance, e.g. shorten the settling time,
increase the set value.
Gain adjustment mode selection
(For more information, refer to section 9.1.1.)
Set value Gain adjustment mode Automatically set parameters
0 Interpolation mode GD2(parameter No.34), PG2(parameter No.35),
VG2(parameter No.37), VIC(parameter No.38)
1 Auto tuning mode 1 PG1(parameter No.7), GD2(parameter No.34),
PG2(parameter No.35), VG1(parameter No.36),
VG2(parameter No.37), VIC(parameter No.38)
2 Auto tuning mode 2 PG1(parameter No.7), PG2(parameter No.35),
VG1(parameter No.36), VG2(parameter No.37),
VIC(parameter No.38)
3 Manual mode 1 PG2(parameter No.35)
4 Manual mode 2
6- 7
6. PARAMETERS
Initial Setting
value range
4 *CMX Electronic gear numerator 1 0 to
Set the value of electronic gear numerator. Setting "0" sets the number of 65535
encoder pulses internally. (Refer to section 6.2.1)
5 *CDV Electronic gear denominator 1 1 to
Set the value of electronic gear denominator. (Refer to section 6.2.1) 65535
6 INP In-position range 100 m 0 to
Used to set the droop pulse range in command unit when Movement finish 10000
(RXnC) or In-position (RYn1) is output.
7 PG1 Position control gain 1 36 rad/s 4 to 1000
Used to set the gain of position loop 1. (Refer to chapter 9)
Increase the gain to improve tracking performance in response to the command.
8 ZTY Home position return type 0010 Refer to
Used to set the home position return system, home position return direction and Name
proximity dog input polarity. (Refer to section 5.4) and
function
0 column.
Home position return system

0: Dog type
1: Count type
2: Data setting type
3: Stopper type
4: Home position ignorance
(Servo-on position as home position)
Basic parameters
5: Dog type rear end reference

6: Count type front end reference
7: Dog cradle type
Home position return direction
0: Address increment direction
1: Address decrement direction
Proximity dog input polarity
0: OFF indicates detection of the dog.
1: ON indicates detection of the dog.
9 ZRF Home position return speed 500 r/min 0 to

Used to set the servo motor speed for home position return. permissible
(Refer to section 5.4) speed
10 CRF Creep speed 10 r/min 0 to
Used to set the creep speed after proximity dog detection. permissible
(Refer to section 5.4) speed
11 ZST Home position shift distance 0 m 0 to 65535
Used to set the shift distance starting at the Z-phase pulse detection position
inside the encoder. (Refer to section 5.4)
12 CRP Rough match output range 0 10STM 0 to 65535
Used to set the command remaining distance range where the rough match m
(RXn2) is output.
13 JOG Jog speed 100 r/min 0 to
Used to set the jog speed command. permissible
speed
14 *STC S-pattern acceleration/deceleration time constant 0 ms 0 to 100
Set when inserting S-pattern time constant into the acceleration/deceleration
time constant of the point table. (Refer to section 6.2.3)
This time constant is invalid for home position return.
6- 8
6. PARAMETERS
Initial Setting
value range
15 *SNO Station number setting 0 station 0 to 31
Used to specify the station number.
Always set one station to one axis of servo amplifier. If one station number is set
to two or more stations, normal communication cannot be made.
16 *BPS Communication baud rate selection, alarm history clear 0000 Refer to
Used to select the serial communication baud rate, select various Name
communication conditions, and clear the alarm history. and
function
0 0 column.
Serial baud rate selection
0: 9600 [bps]
1: 19200[bps]
2: 38400[bps]
3: 57600[bps]
Alarm history clear (Refer to section 6.2.5)

0: Invalid
1: Valid
When alarm history clear is made valid,
the alarm history is cleared at next power-on.
After the alarm history is cleared, the setting
is automatically made invalid (reset to 0).
Basic parameters

Do not change this value by any means.
18 *DMD Status display selection 0000 Refer to
Used to select the status display shown at power-on. (Refer to section 7.2) Name
and
0 0 function
Status display on servo amplifier display column.
at power-on
00: Current position (initial value)
01: Command position
02: Command remaining distance
03: Point table No.
04: Cumulative feedback pulses
05: Servo motor speed
06: Droop pulses
07: For manufacturer adjustment
08: Analog torque limit voltage
09: Regenerative load ratio
0A: Effective load ratio
0B: Peak load ratio
0C: Instantaneous torque
0D: Within one-revolution position low
0E: Within one-revolution position high
0F: ABS counter
10: Load inertia moment ratio
11: Bus voltage
12: Option unit communication status
6- 9
6. PARAMETERS
Initial Setting
value range
19 *BLK Parameter write inhibit 0000 Refer to
Used to select the reference and write ranges of the parameters. Name
Operation can be performed for the parameters marked . and
Option function
Expansion Expansion Special Special
Basic unit
Set parameters parameters parameter parameter column.
Operation parameters parameter
value 1 No.20 to 2 No.54 to 1 No.78 2 No.91
No.0 to 19 No.100 to
53 77 to No.90 to No.99
No.124
0000 Reference
(initial
value) Write
No.19
Reference
Basic parameters
only
000A
No.19
Write
only
Reference
000B
Write
Reference
000C
Write
(Note) Reference
000E Write
(Note) Reference
000F Write
(Note) Reference
00AB Write
Note. Set this parameter when making device setting using the MR Configurator
(Servo Configuration Software).
Used to select slight vibration suppression control. Name
Valid when "03 " or "04 " is set in parameter No. 3 (Auto tuning). and
function
0 0 0 column.
Slight vibration suppression control selection
0: Invalid
1: Valid

22 OP4 Function selection 4 0000 Refer to

Used to select stop processing at forward rotation stroke end (RYn4), reverse Name
rotation stroke end (RYn5) off. and
function
0 0 column.
Stopping method used when forward rotation
stroke end (RYn4), reverse rotation stroke
end (RYn5) device or software limit is valid
0: Sudden stop (home position erased)
1: Slow stop (home position erased)
Stopping method used when software limit is valid

0: Sudden stop (home position erased)
1: Slow stop (home position erased)

6 - 10
6. PARAMETERS
Initial Setting
value range
24 FFC Feed forward gain 0 % 0 to 100
Set the feed forward gain. When the setting is 100%, the droop pulses during
operation at constant speed are nearly zero. However, sudden
acceleration/deceleration will increase the overshoot. As a guideline, when the
feed forward gain setting is 100%, set 1s or more as the
acceleration/deceleration time constant up to the rated speed.
26 Do not change this value by any means. 0
27 4000
28 TL1 Internal torque limit 1 100 % 0 to 100
Used to limit servo motor-torque on the assumption that the maximum torque
is 100%. (Refer to section 4.4.3) When 0 is set, torque is not produced.
29 TL2 Internal torque limit 2 100 % 0 to 100
Used to limit servo motor-torque on the assumption that the maximum torque
is 100%. (Refer to section 4.4.3) When 0 is set, torque is not produced.
Made valid by switching on the internal torque limit selection (RY(n+2)6).
30 *BKC Backlash compensation 0 pulse (Note)
Used to set the backlash compensation made when the command direction is 0
reversed. to
This function compensates for the number of backlash pulses in the opposite 1600
direction to the home position return direction. In the absolute position
detection system, this function compensates for the backlash pulse count in
the direction opposite to the operating direction at power-on.
Note. The setting range differs depending on the software version of servo
amplifiers.
Version A2 or later: 0 to 1600
Version A1 or before: 0 to 1000
33 MBR Electromagnetic brake sequence output 100 ms 0 to 1000
Used to set the delay time (Tb) between when the electromagnetic brake
interlock (MBR) switches off and when the base circuit is shut off.
34 GD2 Ratio of load inertia moment to servo motor inertia moment 70 0.1 0 to 1000
Used to set the ratio of the load inertia moment to the servo motor shaft times
inertia moment. (Refer to chapter 9)
When auto tuning is selected, the result of auto tuning is automatically set.
35 PG2 Position control gain 2 35 rad/s 1 to 1000
Used to set the gain of the position loop. (Refer to chapter 9)
Set this parameter to increase the position response level to load disturbance.
Higher setting increases the response level but is liable to generate vibration
and/or noise.
36 VG1 Speed control gain 1 177 rad/s 20 to
Normally this parameter value need not be changed. 8000
Higher setting increases the response level but is liable to generate vibration
and/or noise. (Refer to chapter 9)
37 VG2 Speed control gain 2 817 rad/s 20 to
Set this parameter when vibration occurs on machines of low rigidity or large 20000
backlash. Higher setting increases the response level but is liable to generate
vibration and/or noise. (Refer to chapter 9)
6 - 11
6. PARAMETERS
Initial Setting
value range
38 VIC Speed integral compensation 48 ms 1 to 1000
Used to set the integral time constant of the speed loop. (Refer to chapter 9)
39 VDC Speed differential compensation 980 0 to 1000
Used to set the differential compensation. (Refer to chapter 9)
Made valid when the proportion control (PC) is switched on.
41 *DSS Remote register-based position/speed specifying system selection 0000 Refer to
This parameter is made valid when Position/speed specification selection Name
(RY(n+2)A) is turned ON with 2 stations occupied. Select how to receive the and
position command and speed command. function
When 1 station is occupied, selection of "0001" or "0002" will result in a column.
parameter error.
0 0 0
Set value Position command Speed command
0 Specify the point table No.
1 Set the position Specify the point table No.
data.
2 Set the servo motor speed.
42 *ZSP Home position return position data 0 10STM 32768

Used to set the current position on completion of home position return. m to
(Refer to section 5.4) 32767
43 DCT Moving distance after proximity dog 1000 10STM 0 to
Used to set the moving distance after proximity dog in count type home m 65535
position return. (Refer to section 5.4.3)
44 ZTM Stopper type home position return stopper time 100 ms 5 to 1000
In stopper type home position return, used to set the time from when the
machine part is pressed against the stopper and the torque limit set in
parameter No.45 is reached to when the home position is set.
45 ZTT Stopper type home position return torque limit value 30 % 1 to 100
Used to set the torque limit value relative to the max. torque in [%] in stopper
type home position return. (Refer to section 5.4.5)
46 LMP Software limit 0 10STM 999999
47 Used to set the address increment side software stroke limit. The software limit m to
is made invalid if this value is the same as in "software limit ". 999999
Set the same sign to parameters No.46 and 47. Setting of different signs will
result in a parameter error.
Set address:
Upper 3 Lower 3
digits digits
Parameter No. 47
Parameter No. 46
6 - 12
6. PARAMETERS
Initial Setting
value range
48 LMN Software limit 0 10STM 999999
49 Used to set the address decrement side software stroke limit. The software limit m to
is made invalid if this value is the same as in "software limit ". 999999
Set the same sign to parameters No.48 and 49. Setting of different signs will
result in a parameter error.
Set address:
Upper 3 Lower 3
digits digits
Parameter No. 49
Parameter No. 48
50 *LPP Position range output address 0 10STM 999999
51 Used to set the address increment side position range output address. Set the m to
same sign to parameters No.50 and 51. Setting of different signs will result in a 999999
parameter error.
In parameters No. 50 to 53, set the range where position range (RXnE) turns on.
(Refer to section 4.3.2 (1)(c))
Set address:
Upper 3 Lower 3
digits digits
Parameter No. 51
Parameter No. 50
52 *LNP Position range output address 0 10STM 999999
53 Used to set the address decrement side position range output address. Set the m to
same sign to parameters No.52 and 53. Setting of different signs will result in a 999999
parameter error.
Set address:
Upper 3 Lower 3
digits digits
Parameter No. 53
Parameter No. 52

Used to select how to process the base circuit when reset (RES) is valid. Name
and
0 0 0 function
column.
Processing of the base circuit when reset (RES) is valid.

0: Base circuit shut off
1: Base circuit not shut off

Used to select the protocol of serial communication. Name
and
0 0 0 function
column.
Protocol checksum selection
0: With station numbers
1: No station numbers
6 - 13
6. PARAMETERS
Initial Setting
value range
60 0000
61 NH1 Machine resonance suppression filter 1 0000 Refer to
Used to selection the machine resonance suppression filter. Name
(Refer to section 10.2) and
function
0 column.
Notch frequency selection

Set "00" when you have set adaptive vibration
suppression control to be "valid" or "held"
(parameter No. 63: 1 or 2 ).
Setting Setting Setting Setting
Frequency Frequency Frequency Frequency
value value value value
00 Invalid 08 562.5 10 281.3 18 187.5
01 4500 09 500 11 264.7 19 180
02 2250 0A 450 12 250 1A 173.1
03 1500 0B 409.1 13 236.8 1B 166.7

04 1125 0C 375 14 225 1C 160.1
05 900 0D 346.2 15 214.3 1D 155.2
06 750 0E 321.4 16 204.5 1E 150
07 642.9 0F 300 17 195.7 1F 145.2
Notch depth selection

Setting
Depth Gain
value
0 Deep 40dB
1 to 14dB
2 8dB
Shallow
3 4dB
62 NH2 Machine resonance suppression filter 2 0000 Refer to

Used to set the machine resonance suppression filter. Name
and
0 function
column.
Notch frequency
Same setting as in parameter No. 61
However, you need not set "00" if you have
set adaptive vibration suppression control to
be "valid" or "held".
Notch depth
Same setting as in parameter No. 61
6 - 14
6. PARAMETERS
Initial Setting
value range
63 LPF Low-pass filter, adaptive vibration suppression control 0000 Refer to
Used to selection the low-pass filter and adaptive vibration suppression Name
control. (Refer to chapter 10) and
function
0 column.
Low-pass filter selection

0: Valid (Automatic adjustment)
1: Invalid
When you choose "valid", the filter of the handwidth
represented by the following expression is set automatically.
For 1kW or less
VG2 setting 10
[Hz]
2 (1 GD2 setting 0.1)
For 2kW or more
VG2 setting 5
[Hz]
2 (1 GD2 setting 0.1)
Adaptive vibration suppression control selection
Choosing "valid" or "held" in adaptive vibration
suppression control selection makes the machine
resonance control filter 1 (parameter No. 61) invalid.

0: Invalid
1: Valid
Machine resonance frequency is always detected
and the filter is generated in response to resonance
to suppress machine vibration.
2: Held
The characteristics of the filter generated so far are held,
and detection of machine resonance is stopped.
Adaptive vibration suppression control sensitivity selection
Used to set the sensitivity of machine resonance detection.
0: Normal
1: Large sensitivity
64 GD2B Ratio of load inertia moment to servo motor inertia moment 2 70 0.1 0 to 3000
Used to set the ratio of load inertia moment to servo motor inertia moment times
when gain changing is valid.
65 PG2B Position control gain 2 changing ratio 100 % 10 to 200
Used to set the ratio of changing the position control gain 2 when gain
changing is valid.
Made valid when auto tuning is invalid.
66 VG2B Speed control gain 2 changing ratio 100 % 10 to 200
Used to set the ratio of changing the speed control gain 2 when gain changing
is valid.
Made valid when auto tuning is invalid.
67 VICB Speed integral compensation changing ratio 100 % 50 to
Used to set the ratio of changing the speed integral compensation when gain 1000
changing is valid. Made valid when auto tuning is invalid.
6 - 15
6. PARAMETERS
Initial Setting
value range
68 *CDP Gain changing selection 0000 Refer to
Used to select the gain changing condition. (Refer to section 10.5) Name
and
0 0 0 function
column.
Gain changing selection

Gains are changed in accordance with the settings
of parameters No. 64 to 67 under any of the following
conditions:
0: Invalid
1: Gain changing (CDP) signal is ON
2: Command frequency is equal to higher than
parameter No. 69 setting
3: Droop pulse value is equal to higher than

4: Servo motor speed is equal to higher than
69 CDS Gain changing condition 10 kpps 10 to
Used to set the value of gain changing condition (command frequency, droop pulse 9999
pulses, servo motor speed) selected in parameter No. 68. The set value unit r/min
changes with the changing condition item. (Refer to section 10.5)
70 CDT Gain changing time constant 1 ms 0 to 100
Used to set the time constant at which the gains will change in response to the
conditions set in parameters No. 68 and 69.
73 10
74 10
75 100
76 100
77 100
78 *DI0 I/O device selection 0000 Refer to
Used to select whether the CN1A-19 pin will be used as an input device or
Name
output device. and
function
0 0 0 column.
CN1A-19 pin
0: Output device
1: Input device
6 - 16
6. PARAMETERS
Initial Setting
value range
79 *DI1 Input device selection 1 0000 Refer to
Used to select the functions of the CN1A-8 and CN1A-19 pins. Name
and
function
column.
Set the function of the CN1A-8 pin.
The set value and its function are the same as
those of the CN1A-19 pin.
Set value Input selection Set value Input selection

00 Without assigned function 13
01 Forced stop 14
02 Servo-on 15
03 Reset 16
04 Forward rotation stroke end 17
05 Reverse rotation stroke end 18
06 Forward rotation start 19
07 Reverse rotation start 1A
08 Automatic/manual selection 1B
09 Proximity dog 1C
0A 1D
0B 1E
0C 1F
0D 20 Point table No. selection 1
0E 21 Point table No. selection 2
0F 22 Point table No. selection 3
10 Internal torque limit selection 23 Point table No. selection 4
11 Proportion control 24 Point table No. selection 5
12 Temporary stop/Restart 25

Used to select the functions of the CN1B-5 and CN1B-7 pins. Name
and
function
column.
Set the function of the CN1B-5 pin.
The set value and its function are the same as those of the
CN1A-19 pin. Refer to parameter No. 79 (input device
selection 1).
selection 1).
6 - 17
6. PARAMETERS
Initial Setting
value range
and
function
column.
selection 1).
selection 1).

and
function
column.
selection 1).
selection 1).

and
function
column.
selection 1).
selection 1).
6 - 18
6. PARAMETERS
Initial Setting
value range
Select the function device signals that will turn ON automatically. Name
and
0 function
Initial value column.
Signal name
BIN HEX
0
Forced stop 0
0
Servo-on 0
0
Initial value
Signal name
BIN HEX
Forward rotation stroke 0
Reverse rotation stroke 0
0
0
0
Initial value
Signal name
BIN HEX
Automatic/manual 0
0
0
0
0
BIN 0: Used in CC-Link or as external input
signal
BIN 1: Automatic ON

Select the function device signal that will turn ON automatically. Name
and
0 0 0 function
Signal name
BIN HEX
0
0
0
0
signal
BIN 1: Automatic ON
6 - 19
6. PARAMETERS
Initial Setting
value range
Select the function device signals that will turn ON automatically. Name
and
0 0 function
Signal name
BIN HEX
0
Initial value
Signal name
BIN HEX
0
0
0
0
signal
BIN 1: Automatic ON

88 *DO1 Output device selection 1 0005 Refer to
Name
and
function
column.
The set value and its function are the same as
those of the CN1A-19 pin.
Set value Output selection Set value Output selection

00 Without assigned function 13
01 Ready 14
02 Trouble 15
03 In position 16
04 Rough match 17
05 18
completion
06 19
interlock
07 1A
08 Position range 1B
09 Warning 1C
0A Battery warning 1D
0B Limiting torque 1E
0C Temporary stop 1F
0D Movement finish 20 Point No. output 1
0E 21 Point No. output 2
0F 22 Point No. output 3
10 23 Point No. output 4
11 24 Point No. output 5
12 25
6 - 20
6. PARAMETERS
Initial Setting
value range
89 *DO2 Output device selection 2 0D04 Refer to
and
function
column.
CN1A-19 pin. Refer to parameter No. 88 (output device
selection 1).
selection 1).
90 *DO3 Output device selection 3 0102 Refer to

and
function
column.
selection 1).
selection 1).

93 400
94 100
95 1
96 1
97 0
98 50
99 0000
102 0000
103 0000
104 1
105 1
106 0
107 0
108 0
109 0
110 0
111 0
112 0
113 0
114 0
115 0001
6 - 21
6. PARAMETERS
Initial Setting
value range
116 *IN1 External I/O function selection 1 0230 Refer to
Set any signals to be imported from CN1. Name
and
0 function
Signal name
BIN HEX
0
0
0
Servo-on 0
Reset 0
Initial value
Signal name
BIN HEX
Forward rotation stroke end 1
Reverse rotation stroke end 1
3
Forward rotation start 0
Reverse rotation start 0
Initial value
Signal name
BIN HEX
Automatic/manual 0
Proximity dog 1
2
0
0
BIN 1: Used as CN1A/CN1B external input
signal

and
0 0 function
Signal name
BIN HEX
Internal torque limit selection 0
0
Temporary stop/Restart 0
0
Initial value
Signal name
BIN HEX
1
1
0
0
Gain changing selection 0
signal
6 - 22
6. PARAMETERS
Initial Setting
value range
and
0 0 function
Signal name
BIN HEX
0
Initial value
Signal name
BIN HEX
0
0
0
0
signal

121 0
122 0
123 0
124 0
6 - 23
6. PARAMETERS
6.2 Detailed explanation
6.2.1 Electronic gear
CAUTION False setting will result in unexpected fast rotation, causing injury.
POINT
1 CMX
The range of the electronic gear setting is. 1000. If you set
10 CDV
any value outside this range, a parameter error (AL.37) occurs.
After setting the parameter No.4, 5 value, switch power off, then on to
make that setting valid.
(1) Concept of electronic gear

Use the electronic gear (parameters No.4, 5) to make adjustment so that the servo amplifier setting
matches the moving distance of the machine. Also, by changing the electronic gear value, the machine
can be moved at any multiplication ratio to the moving distance on the servo amplifier.
Motor
CMX Parameter No. 4
distance
CMX + Deviation
Moving
CDV Parameter No. 5 CDV - counter
Encoder feedback pulses

Electronic gear
Parameters No. 4, 5 Encoder
The following examples are used to explain how to calculate the electronic gear value.
POINT
The following specification symbols are needed for electronic gear
calculation.
Pb : Ballscrew lead [mm(in.)]
n : Reduction ratio
Pt : Servo motor resolution [pulse/rev]
S : Travel per servo motor revolution [mm/rev]
(a) Ballscrew setting example n

Machine specifications n=NL/NM=1/2
NL
Ballscrew lead: Pb 10 (0.39) [mm(in.)] Pb=10(0.39)[mm(in.)]
Reduction ratio: n 1/2 NM
Servo motor resolution: Pt 131072 [pulse/rev] Servo motor 131072[pulse/rev]
CMX pt pt 131072 131072 32768
CDV S n pb 1000 1/2 10 1000 5000 1250
Hence, set 32768 to CMX and 1250 to CDV.
(b) Conveyor setting example r=160(6.30)[mm(in.)]
Machine specifications
Pulley diameter: r 160 (6.30) [mm(in.)] n Servo motor

131072[pulse/rev]
Reduction ratio: n 1/3 NL NM
Servo motor resolution: Pt 131072 [pulse/rev] n=NL/NM=1/3
CMX pt pt 131072 131072 32768

CDV S n r 1000 1/3 160 1000 167551.61 41888
Reduce CMX and CDV to the setting range or less, and round off the first decimal place.
Hence, set 32768 to CMX and 41888 to CDV.
6 - 24
6. PARAMETERS
6.2.2 Changing the status display screen
The status display item of the servo amplifier display shown at power-on can be changed by changing the
parameter No.18 (status display selection) settings. In the initial condition, the servo amplifier display
shows the servo motor speed.
For display details, refer to section 8.2.
Parameter No. 18
0 0
Status display on servo amplifier display
at power-on
00: Current position (initial value)
01: Command position
02: Command remaining distance
03: Point table No.
04: Cumulative feedback pulses
05: Servo motor speed
06: Droop pulses
07: For manufacturer setting
08: Analog torque limit voltage
09: Regenerative load ratio
0A: Effective load ratio
0B: Peak load ratio
0C: Instantaneous torque
0D: Within one-revolution position low
0E: Within one-revolution position high
0F: ABS counter
10: Load inertia moment ratio
11: Bus voltage
12: Option unit communication status
6.2.3 S-pattern acceleration/deceleration
In servo operation, linear acceleration/deceleration is usually made. By setting the S-pattern

acceleration/deceleration time constant (parameter No.14), a smooth start/stop can be made. When the S-
pattern time constant is set, smooth positioning is executed as shown below. Note that the time
equivalent to the S-pattern time constant setting increases until positioning (RXnC) is complete.
Acceleration time Deceleration time
constant constant
Rated
speed
Preset
speed
Servo motor
speed
0 [r/min]
Ta Tb Ts
Ta Ts Tb
Ta: Time until preset speed is reached

Tb: Time until stop
Ts: S-pattern acceleration/deceleration time constant
(parameter No. 14)
Setting range 0 to 100ms
6 - 25
6. PARAMETERS
6.2.4 Changing the stop pattern using a limit switch
The servo amplifier is factory-set to make a sudden stop when the limit switch or software limit is made
valid. When a sudden stop is not required, e.g. when there is an allowance from the limit switch
installation position to the permissible moving range of the machine, a slow stop may be selected by
changing the parameter No.22 setting.
Parameter No. 22 setting Description
0 (initial value) Droop pulses are reset to make a stop. (Sudden stop)
1 Droop pulses are drawn out to make a slow stop. (Slow stop)
6.2.5 Alarm history clear
The alarm history can be confirmed by using the MR Configurator (Servo Configuration Software). The
servo amplifier stores one current alarm and five past alarms from when its power is switched on first. To
control alarms which will occur during operation, clear the alarm history using parameter No.16 (alarm
history clear) before starting operation. Clearing the alarm history automatically returns to “ 0 ”.
This parameter is made valid by switching power off, then on after setting.
Parameter No. 16
Alarm history clear

0: Invalid (not cleared)
1: Valid (cleared)
6.2.6 Rough match output
Rough match (RXn2) is output when the command remaining distance reaches the value set in parameter
No. 12 (rough match output range). The set remaining distance is 0 to 65535 [ 10STM m].
Command remaining distance ( 10STM m)
set in parameter No. 12
Actual servo motor speed

Servo motor
Command pulse
speed
Rough match ON
(RXn2) OFF
ON
In position (RXnC)
OFF
6.2.7 Software limit
A limit stop using a software limit is made as in stroke end operation. When a motion goes beyond the
setting range, the motor is stopped and servo-locked. This function is made valid at power-on but made
invalid during home position return. This function is made invalid when the software limit setting is
the same as the software limit setting. A parameter error (AL. 37) will occur if the software limit
setting is less than the software limit setting.
Inhibited area
Movable area
Unmovable Movable
Current position
Software limit
6 - 26
7. MR Configurator (SERVO CONFIGURATION SOFTWARE)
The MR Configurator (Servo Configuration software) (MR2JW3-SETUP161E) uses the communication

function of the servo amplifier to perform parameter setting changes, graph display, test operation, etc. on
a personal computer.
7.1 Specifications
Item Description
Communication signal Conforms to RS-232C
Baud rate 57600, 38400, 19200, 9600
System Station selection
Monitor Display all High-speed monitor, trend graph
Alarm Display, history, amplifier data
I/O display, function device display, no motor rotation, total power-on time, software number
Diagnostic
display, motor data display, tuning data, absolute encoder data, axis name setting
Parameters Parameter list, tuning, change list, detailed information, device setting
Test Jog, positioning, operation w/o motor, forced output, single-step feed.
Advanced-function Machine analyzer, gain search, machine simulation
Program-data Point table
File operation Data read, save, print
Others Help display
7.2 System configuration
(1) Components
To use this software, the following components are required in addition to the servo amplifier and
servo motor.
Model (Note 1) Description

IBM PC-AT compatible where the English version of Windows® 95, Windows® 98, Windows® Me,
Windows NT® Workstation 4.0, Windows® 2000 Professional, Windows® XP Professional or Windows®
XP Home Edition operates
Processor: Pentium® 133MHz or more (Windows® 95, Windows® 98,Windows NT® Workstation 4.0,
Windows® 2000 Professional)
Pentium® 150MHz or more (Windows® Me)
(Note 2)
Pentium® 300MHz or more (Windows® XP Professional, Windows® XP Home Edition)
Personal computer
Memory: 16MB or more (Windows® 95), 24MB or more (Windows® 98)
32MB or more (Windows® Me, Windows NT® Workstation 4.0, Windows® 2000
Professional)
128MB or more (Windows® XP Professional, Windows® XP Home Edition)
Free hard disk space: 60MB or more
Serial port used
Windows® 95, Windows® 98, Windows® Me, Windows NT® Workstation 4.0, Windows® 2000
OS
Professional, Windows® XP Professional, Windows® XP Home Edition (English version)
One whose resolution is 800 600 or more and that can provide a high color (16 bit) display.
Display
Connectable with the above personal computer.
Keyboard Connectable with the above personal computer.
Mouse Connectable with the above personal computer. Note that a serial mouse is not used.
Printer Connectable with the above personal computer.
MR-CPCATCBL3M
Communication cable
When this cannot be used, refer to (3) section 15.1.4 and fabricate.
Note 1. Windows and Windows NT are the registered trademarks of Microsoft Corporation in the United State and other countries.
Pentium is the registered trademarks of Intel Corporation.
2. On some personal computers, this software may not run properly.
7- 1
(2) Configuration diagram

For use of RS-232C
Servo amplifier
U
Personal computer V
W
Communication
cable
CN3 CN2 Servo motor
To RS-232C MR-J2S-T01
CC-Link option unit
CN30
CN40
MR-JRPCATCBL 3M
7- 2
7.3 Station setting
Click “System” on the menu bar and click “Station Selection” on the menu.
When the above choices are made, the following window appears.
(1) Station number setting

Choose the station number in the combo box and click the “Station Settings” button to set the station
number.
POINT
This setting should be the same as the station number which has been set
in the parameter in the servo amplifier used for communication.
(2) Closing of the station setting window

Click the “Close” button to close the window.
7- 3
7.4 Parameters
Click “Parameters” on the menu bar and click “Parameter List” on the menu.
a)
b)
c)
d)
e)
f)
g)
h)
(1) Parameter value write ( a) )

Click the parameter whose setting was changed and press the “Write” button to write the new
parameter setting to the servo amplifier.
(2) Parameter value verify ( b) )

Click the “Verify” button to verify all parameter values being displayed and the parameter values of
7- 4
(3) Parameter value batch-read ( c) )

Click the “Read All” button to read and display all parameter values from the servo amplifier.
(4) Parameter value batch-write ( d) )

Click the “Write All” button to write all parameter values to the servo amplifier.
(5) Parameter change list display ( e) )

Click the “Change List” button to show the numbers, names, initial values and current values of the
parameters whose initial value and current value are different. In the offline mode, the parameter
change list is not shown.
(6) Parameter default value indication ( f) )

Click the “Set to default” button to show the initial value of each parameter.
(7) Parameter value change ( g) )

Choose the parameter to be changed, enter a new value into the “Parameter value” input field, and
press the enter key or Enter Data button.
(8) Parameter data file read

Used to read and display the parameter values stored in the file. Use the file selection window to read.
(9) Parameter value storage

Used to store all parameter values being displayed on the window into the specified file. Use the file
selection window to store.
(10) Parameter data list print

Used to print all parameter values being displayed on the window. Use the “File” menu on the menu
bar to print.
(11) Parameter list window closing ( h) )

Click the “Close” button to close the window. If the “Close” button is clicked without (1) parameter
value write or (4) parameter value batch-write being performed, the parameter value changed is
made invalid.
7- 5
7.5 Point table
Click “Position-Data” on the menu bar and click “Point Tables” on the menu.
a)
b)
c)
d)
h)
e) g) f)
(1) Point table data write ( a) )

Click the point table data changed and press the “Write” button to write the new point table data to the
servo amplifier.
(2) Point table data verify ( b) )

Click the “Verify” button to verify all data being displayed and the data of the servo amplifier.
7- 6
(3) Point table data batch-read ( c) )

Click the “Read All” button to read and display all point table data from the servo amplifier.
(4) Point table data batch-write ( d) )

Click the “Write All” button to write all point table data to the servo amplifier.
(5) Point table data insertion ( e) )

Click the “Insert Row” button to insert one block of data into the position before the point table No.
chosen. The blocks after the chosen point table No. are shifted down one by one.
(6) Point table data deletion ( f) )

Click the “Delete Row” button to delete all data in the point table No. chosen. The blocks after the
chosen point table No. are shifted up one by one.
(7) Point table data change ( g) )

Click the data to be changed, enter a new value into the “Setting” input field, and press the enter key
or Enter Data button.
(8) Point table data file read

Used to read and display the point table data stored in the file. Use the “File” menu on the menu bar to
read.
(9) Point table data storage

Used to store all point table data being displayed on the window into the specified file. Use the “File”
menu on the menu bar to store.
(10) Point table data list print

Used to print all point table data being displayed on the window. Use the “File” menu on the menu
bar to print.
(11) Point table data list window closing ( h) )

7- 7
7.6 Device assignment method
POINT
When using the device setting, preset “000E” in parameter No. 19.
(1) How to open the setting screen

Click “Parameters” on the menu bar and click “Device setting” in the menu.
Making selection displays the following window.
Click “Yes” button reads and displays the function assigned to each pin from the interface unit and
extension IO unit.
Click “No” button displays the initial status of the interface unit and extension IO unit.
Click “Cancel” button terminates the processing.
Click “Yes” button or “No” button displays the following two windows.
7- 8
(2) Screen explanation

(a) DIDO device setting window screen
This is the device assignment screen of the servo amplifier displays the pin assignment status of
a)
b)
c)
d)
1) Read of function assignment ( a) )

Click the “Read” button reads and displays all functions assigned to the pins from the servo
amplifier.
2) Write of function assignment ( b) )

Click the “Write” button writes all pins that are assigned the functions to the servo amplifier.
3) Verify of function assignment ( c) )

Click the “Verify” button verifies the function assignment in the servo amplifier with the device
information on the screen.
4) Initial setting of function assignment ( d) )

Click the “Set to Default” button initializes the function assignment.
7- 9
(b) DIDO function display window screen

This screen is used to select the device assigned to the pins.
The functions displayed below * and * are assignable.
a)
b)
Move the pointer to the place of the function to be assigned. Drag and drop it as-is to the pin you
want to assign in the DIDO device setting window.
1) Assignment checking, automatic ON setting ( a) )

Press this button to display the screen that shows the assignment list and enables auto ON
setting.
Refer to (c) in this section for more information.
2) Quitting
Click “Close” button to exit from the window. ( b) )
7 - 10
(C) Function device assignment checking auto ON setting display

Click the “ / ” button in the DIDO function display window displays the following window.
a)
b)
c)
d)
e)
The assigned functions are indicated by .

The functions assigned by auto ON are grayed. When you want to set auto ON to the function that
is enabled for auto ON, click the corresponding cell. Clicking it again disables auto ON.
1) Auto ON read of function assignment ( a) )

Click “Auto ON read” button reads the functions set for auto ON from the interface unit and
extension IO unit.
2) Auto ON write of function assignment ( b) )

Click “Auto ON write” button writes the functions currently set for auto ON to the interface unit
and extension IO unit.
3) Auto ON verify of function assignment ( c) )

Click “Auto ON verify” button verifies the current auto ON setting in the interface unit and
extension IO unit with the auto ON setting on the screen.
4) Auto ON initial setting of function assignment ( d) )

Click “Auto ON initial setting” button initializes the auto ON setting.
5) Quitting the function device assignment checking/auto ON setting window ( e) )

Click “Close” button exits from the window.
7 - 11
7.7 Test operation
When confirming the machine operation in the test operation mode, use the
machine after checking that the safety mechanism such as the forced stop (EMG)
CAUTION operates.
If any operational fault has occurred, stop operation using the forced stop (EMG).
7.7.1 Jog operation
POINT
For the program operation, refer to the manual of MR Configurator.
The servo motor will not operate if the forced stop (EMG), forward
rotation stroke end (LSP) and reverse rotation stroke end (LSN) are off.
Make automatic ON setting to turn on these devices or make device
setting to assign them as external input signals and turn on across these
signals and SG. (Refer to section 7.6.)
When an alarm occurs, the JOG operation is automatically canceled.
Hold down the “Forward” or “Reverse” button to rotate the servo motor. Release the “Forward” or
“Reverse” button to stop.
Click “Test” on the menu bar and choose “Jog” on the menu.
Clicking displays the following window.
Since this window shows the precaution for use of the MR-J2S-B, click the "OK" button.
7 - 12
a)
c)
b) d)
e)
f)
(1) Servo motor speed setting ( a) )

Enter a new value into the “Motor speed” input field and press the enter key.
(2) Acceleration/deceleration time constant setting ( b) )

Enter a new value into the “Accel/decel time” input field and press the enter key.
(3) Servo motor start ( c), d) )

Hold down the “Forward” button to rotate the servo motor in the CCW rotation direction.
Hold down the “Reverse” button to rotate the servo motor in the CW rotation direction.
(4) Servo motor stop ( e) )

Release the “Forward” or “Reverse” button to stop the rotation of the servo motor.
(5) Jog operation window closing ( f) )

Click the “Close” button to cancel the jog operation mode and close the window.
(6) Cancel of jog operation

To cancel jog operation, switch off the power of the servo amplifier.
7 - 13
7.7.2 Positioning operation
POINT
When an alarm occurs, the positioning operation is automatically
canceled.
Click the “Forward” or “Reverse” button to start and rotate the servo motor by the preset moving distance
and then stop.
Click “Test” on the menu bar and click “Positioning” on the menu.
7 - 14
a)
d)
b)
e)
c)
f)
g)
(1) Servo motor speed setting ( a) )

Enter a new value into the “Motor speed” input field and press the enter key.
(2) Acceleration/deceleration time constant setting ( b) )

Enter a new value into the “Accel/decel time” input field and press the enter key.
(3) Moving distance setting ( c) )

Enter a new value into the “Move distance” input field and press the enter key.
(4) Servo motor start ( d), e) )

Click the “Forward” button to rotate the servo motor in the forward rotation direction.
Click the “Reverse” button to rotate the servo motor in the reverse rotation direction.
(5) Temporary stop of servo motor ( f) )

Click the “Pause” button to stop the servo motor temporarily.
(6) Positioning operation window closing ( g) )

Click the “Close” button to cancel the positioning operation mode and close the window.
(7) Cancel of positioning operation

To cancel positioning operation, switch off the power of the servo amplifier.
7 - 15
7.7.3 Motor-less operation
POINT
When this operation is used in an absolute position detection system, the
home position cannot be restored properly.
Without a servo motor being connected, the output signals are provided and the servo amplifier display
shows the status as if a servo motor is actually running in response to the external I/O signals.
The sequence of the host programmable controller can be checked without connection of a servo motor.
Click “Test” on the menu bar and click “Operation w/o Motor” on the menu.
a) b)
(1) Execution of motor-less operation ( a) )

Click “Start” to perform motor-less operation.
(2) Termination of motor-less operation ( b) )

Click “Close” to close the window.
(3) Cancel of motor-less operation

To cancel motor-less operation, switch off the power of the servo amplifier.
7 - 16
7.7.4 Output signal (DO) forced output
POINT
When an alarm occurs, the DO forced output is automatically canceled.
Each servo amplifier output signal is forcibly switched on/off independently of the output condition of the
output signal.
Click “Test” on the menu bar and click “Forced Output” on the menu.
a)
b)
c)
(1) Signal ON/OFF setting ( a), b) )

Choose the signal name or pin number and click the “ON” or “OFF” button to write the corresponding
signal status to the servo amplifier.
(2) DO forced output window closing ( c) )

Click the “Close” button to cancel the DO forced output mode and close the window.
(3) Cancel of DO forced output

To cancel DO forced output, switch off the power of the servo amplifier.
7 - 17
7.7.5 Single-step feed
POINT
When an alarm occurs, the 1-step feed is automatically canceled.
Operation is performed in accordance with the preset point table No.

Click “Test” on the menu bar and click “Single-step Feed” on the menu.
a)
b)
c)
d)
7 - 18
(1) Point table No. setting ( a) )

Enter the point table No. into the “Point table No.” input field and press the enter key.
(2) Servo motor start ( b) )

Click the “Start” button to rotate the servo motor.
(3) Temporary stop of servo motor ( c) )

Press the “Pause” button to stop the servo motor temporarily.
(4) Servo motor stop ( d) )

Click the “Pause” button again during a temporary stop of the servo motor to clear the remaining
moving distance.
(5) Single-step feed window closing ( e) )

Click the “Close” button to cancel the single-step feed mode and close the window.
(6) Cancel of single-step feed

To cancel single-step feed, switch off the power of the servo amplifier.
7 - 19
7.8 Alarm history
Click “Alarms” on the menu bar and click “History” on the menu.
a) b)
(1) Alarm history display

The most recent six alarms are displayed. The smaller numbers indicate newer alarms.
(2) Alarm history clear ( a) )

Click the “Clear” button to clear the alarm history stored in the servo amplifier.
(3) Closing of alarm history window ( b) )

7 - 20
8. DISPLAY AND OPERATION
8.1 Display flowchart
Use the display (5-digit, 7-segment LED) on the front panel of the servo amplifier for status display,
parameter setting, etc. Set the parameters before operation, diagnose an alarm, confirm external
sequences, and/or confirm the operation status.
8.1.1 Display flowchart from powering ON to OFF
Servo amplifier power ON
Communication waiting status (Note)
During initialization
communication
It is difficult to check with eyes due to normal transit

in a short time.
During communication
Normal operation display (Refer to section 8.1.2)
Communication error
(Note)
Servo amplifier power OFF
or
Turn the servo amplifier OFF and eliminate its cause

referring to section 12.4.
Note. MR-J2S-T01 optional module is not connected.
MR-J2S-T01 optional module will be unconnected during powering ON.
For these status, turning the servo amplifier OFF and connect MR-J2S-T01 properly.
8- 1
8.1.2 Display mode transition
Press the "MODE" "UP" or "DOWN" button once to move to the next screen. Refer to section 8.2 and later
for the description of the corresponding display mode.
To refer to or set the expansion parameters 1, expansion parameters 2, special parameters 1, special
parameters 2 and option unit parameter make them valid with parameter No.19 (parameter write
disable).
Display mode transition Initial screen Function Reference

Servo status display.
At power-on, appears after
Section 8.2
Status display displaying MR-J2S-T01 option unit
communication.
Alarm display, external signal display, output
signal (DO) forced output, test operation,
software version display, VC automatic offset, Section 8.3
Diagnosis
motor series ID display, motor type ID display,
encoder ID display
Current alarm display, alarm history display,
parameter error No. display, point table error
Alarm No. display. Section 8.4
Display and setting of point table data.
Point table Section 8.5
Display and setting of basic parameters.
Basic parameter
button
MODE Display and setting of expansion parameters 1.
Expansion parameter 1
Display and setting of expansion parameters 2.

Expansion parameter 2
Section 8.6
Display and setting of special parameters 1.
Special parameter 1
Display and setting of special parameters 2.

Special parameter 2
Display and setting of option unit parameter.

8- 2
8.2 Status display
The servo status during operation is shown on the 5-digit, 7-segment LED display. Press the "UP" or
"DOWN" button to change display data as desired. When the required data is selected, the corresponding
symbol appears. Press the "SET" button to display its data. At only power-on, however, data appears after
the symbol of the status display selected in parameter No. 18 has been shown for 2[s].
The servo amplifier display shows the lower five digits of 16 data items such as the motor speed.
8.2.1 Display transition
After choosing the status display mode with the "MODE" button, pressing the "UP" or "DOWN" button
changes the display as shown below.
To Bus voltage
Current position Regenerative load ratio
Command position Effective load ratio
Command remaining
Peak load ratio
distance
Point table No. Instantaneous torque
Cumulative feedback Within one-revolution

pulses UP position Low
DOWN
Within one-revolution
Servo motor speed position High
Droop pulses ABS counter
For manufacturer setting Load inertia moment ratio
For manufacturer setting Bus voltage
Option unit communication

status
To Current position
8- 3
8.2.2 Display examples
The following table lists display examples.
Item Status Displayed data
Forward rotation
at 2500r/min
Servo motor
speed
Reverse rotation
at 3000r/min
Reverse rotation is indicated by " ".
Load inertia
15.5 times
moment
11252pulse
Multi-
revolution
counter
12566pulse
Lit
Negative value is indicated by the lit

decimal points in the upper four digits.
8- 4
8.2.3 Status display list
The following table lists the servo statuses that may be shown.
Status display Symbol Unit Description Display range
10STM The current position from the machine home position of 0 is 99999 to
Current position PoS
mm displayed. 99999
10STM The command position is displayed. 99999 to
Command position CPoS
mm 99999
Command 10STM The command remaining distance of the currently selected point table 99999 to
rn
remaining distance mm is displayed. 99999
Point table No. PT The point table No. being executed is displayed. 0 to 31
Feedback pulses from the servo motor encoder are counted and
Cumulative displayed. 99999 to
C pulse
feedback pulses When the value exceeds 9999999, it returns to zero. 99999
Press the "SET" button to reset the display value to zero.
The servo motor speed is displayed.
5400 to
Servo motor speed r r/min " " is added to the speed of the servo motor rotating in the CW
5400
rotation.
The number of droop pulses in the deviation counter is displayed.
" " is added to the droop pulses in the CW rotation. 99999 to
Droop pulses E pulse
The displayed number of pulses is not yet multiplied by the electronic 99999
gear value.
For manufacturer F % For manufacturer setting. 0 to 200
setting u V 0.00 to 10.00
Regenerative load The ratio of regenerative power to permissible regenerative power is
L % 0 to 100
ratio displayed in %.
The continuous effective load torque is displayed.
Effective load ratio J % The effective value in the past 15 seconds is displayed relative to the 0 to 300
rated torque of 100%.
The maximum torque generated during acceleration/deceleration, etc.
Peak load ratio b % The highest value in the past 15 seconds is displayed relative to the 0 to 300
rated torque of 100%.
Torque that occurred instantaneously is displayed.
Instantaneous
T % The value of the torque that occurred is displayed in real time relative 0 to 400
torque
to the rate torque of 100%.
Position within one revolution is displayed in encoder pulses.
Within one-
The value returns to 0 when it exceeds the maximum number of
revolution position Cy1 pulse 0 to 99999
pulses.
Low
The value is incremented in the CCW direction of rotation.
The within one-revolution position is displayed in 100 pulse
Within one- increments of the encoder.
100
revolution position Cy2 The value returns to 0 when it exceeds the maximum number of 0 to 1310
pulse
High pulses.
The value is incremented in the CCW direction of rotation.
Travel value from the home position in the absolute position detection
32768 to
ABS counter LS rev systems is displayed in terms of the absolute position detectors
32767
counter value.
Load inertia The estimated ratio of the load inertia moment to the servo motor
dC times 0.0 to 300.0
moment ratio shaft inertia moment is displayed.
Bus voltage Pn V The voltage (across P-N) of the main circuit converter is displayed. 0 to 450
Communication waiting status AA Ab
Option unit
During initialization communication AC Ad
communication oS
During communication CO
status
Communication stop status due to alarm
8- 5
8.3 Diagnosis mode
After choosing the diagnosis mode with the "MODE" button, pressing the "UP" or "DOWN" button changes
the display as shown below.
To Teaching
Sequence Software version Low
External I/O signal display Software version High
Output signal (DO) Option unit software version

forced output Low
Test operation mode Option unit software version

Jog feed UP High
DOWN
Test operation mode
Positioning operation
Test operation mode

Motor series ID
Motor-less operation
Test operation mode

Machine analyzer operation Motor type ID
Encoder ID
For manufacture setting
To Sequence
8- 6
8.3.2 Diagnosis mode list
Name Display Description

Not ready.
Indicates that the servo amplifier is being initialized or an alarm
has occurred.
Sequence
Ready.
Indicates that the servo was switched on after completion of
initialization and the servo amplifier is ready to operate.
Indicates the ON-OFF states of the external I/O signals.

The upper segments correspond to the input signals and the
lower segments to the output signals.
External I/O signal
Refer to section 8.7. Lit: ON
display
Extinguished: OFF
The I/O signals can be changed using the MR Configurator (servo
configuration software MRZJW3-SETUP161E).
The digital output signal can be forced on/off. (Refer to section
Output signal (DO) 8.8)
forced output
Jog operation can be performed when there is no command from

the external command device. (Refer to section 8.9.2)
Jog feed
The MR Configurator (servo configuration software MRZJW3-

SETUP161E) is required for positioning operation. This operation
Positioning cannot be performed from the operation section of the servo
operation amplifier.
Test
Positioning operation can be performed once when there is no
operation
command from the external command device.
mode
Without connection of the servo motor, the servo amplifier
Motor-less provides output signals and displays the status as if the servo
operation motor is running actually in response to the external input
signal. (Refer to section 8.9.4)
Merely connecting the servo amplifier allows the resonance point
Machine
of the mechanical system to be measured.
analyzer
The MR Configurator (servo configuration software MRZJW3-
operation
SETUP161E) is required for machine analyzer operation.
Indicates the version of the software.
Software version Low
Indicates the system number of the software.

Software version High
Indicates the version of the option unit software.

Option unit software
version Low
Indicates the version of the option unit software.

Option unit software
version High
Manufacturer setting screen. Do not perform operation on this

For manufacturer screen.
setting
8- 7

Press the "SET" button to show the motor series ID of the servo
motor currently connected.
Motor series ID
For indication details, refer to the optional MELSERVO Servo
Motor Instruction Manual.
Press the "SET" button to show the motor type ID of the servo
motor currently connected.
Motor type ID
Press the "SET" button to show the encoder ID of the servo motor
currently connected.
Encoder ID
This is the screen for manufacturer setting. Do not perform
For manufacturer operation on this screen.
setting
8- 8
8.4 Alarm mode
The current alarm, past alarm history and parameter error are displayed. The lower 2 digits on the
display indicate the alarm number that has occurred or the parameter number in error. Display examples
are shown below.
After choosing the alarm mode with the "MODE" button, pressing the "UP" or "DOWN" button changes the
display as shown below.
To Parameter error No.
Alarm history
Current alarm
(Fourth alarm in past)
Alarm history Alarm history

(Last alarm) (Fifth alarm in past)
UP
Alarm history Alarm history

(Second alarm in past) DOWN (Sixth alarm in past)
Alarm history
(Third alarm in past) Parameter error No.
To Current alarm
8- 9
8.4.2 Alarm mode list

Indicates no occurrence of an alarm.
Current alarm
Indicates the occurrence of overvoltage (AL.33).
Flickers at occurrence of the alarm.
Indicates that the last alarm is overload 1 (AL.50).
Indicates that the second alarm in the past is overvoltage

(AL.33).
Indicates that the third alarm in the past is undervoltage

(AL.10).
Alarm history
Indicates that the fourth alarm in the past is overspeed (AL.31).
Indicates that there is no fifth alarm in the past.
Indicates that there is no sixth alarm in the past.
Indicates no occurrence of parameter error.
Indicates that the data of parameter No. 1 is faulty.
Parameter error No.

Displayed when any of the set point table values exceeds the
setting range.
The display given on the left indicates an error in the position
data of point table No. 1.
P: Position data, d: Servo motor speed, A: Acceleration time
constant, b: Deceleration time constant, n: Dwell,
H: Auxiliary function
8 - 10
Functions at occurrence of an alarm

(1) The current occurring alarm is displayed. If an alarm occurs while viewing the other mode screen, the
screen switches to this screen automatically.
(2) If during alarm occurrence, the other screen can be viewed by pressing the button in the operation
section. At this time, the decimal point in the fourth digit remains flickering.
(3) For any alarm, remove its cause and clear it in any of the following methods (for clearable alarms,
refer to section 12.4.1).
(a) Switch power OFF, then ON.
(b) Press the "SET" button on the current alarm screen.
(c) Turn on the reset (RY(n+1)A or RY(n+3)A) signal.
(4) Use parameter No. 16 to clear the alarm history.
(5) Pressing "SET" on the alarm history display screen for 2s or longer shows the following detailed
information display screen. Note that this is provided for maintenance by the manufacturer.
(6) Press "UP" or "DOWN" to move to the next history.
8 - 11
8.5 Point table mode
You can set the target position, servo motor speed, acceleration time, deceleration time, dwell and auxiliary
function.
8.5.1 Point table transition
After choosing the point table mode with the "MODE" button, pressing the "UP" or "DOWN" button
changes the display as shown below.
Point table No. 1
Point table No. 2
UP
DOWN
Point table No. 30
Point table No. 31
8 - 12
8.5.2 Point table mode setting screen sequence
Press "SET" in the point table mode. The following screen appears.
Press "UP" or "DOWN" to move to the next screen.
Position data
Servo motor speed
UP

DOWN
Dwell
Auxiliary function
8 - 13
8.5.3 Operation method
(1) Setting of 5 or less-digit value

The following example provides the after-power-on operation procedure to set "1" in the auxiliary
function of point table No.1.
(Note)
Press MODE three times.
··········The point table No. appears.
Press UP or DOWN to choose point table No. 1.
Press SET once.
Press UP five times.
Press SET twice.
··········The setting of the specified point table No. flickers.
Press UP once.
··········The setting can be changed during flickering.
Use UP or DOWN to change the setting.
Press SET to enter the value.
Note. The example assumes that the status display screen that appears at power-on has been
set to the servo motor speed in parameter No. 18.
Press "UP" or "DOWN" after completion of the setting to return to the setting item screen. Further,
press "UP" and "DOWN" together to return to the point table No. display screen.
During flickering, press "MODE" for 2[s] to discard the new value and display the old value.
8 - 14
(2) Setting of 6 or more-digit value

The following example gives the after-power-on operation procedure to change the target value of
point table No.1 to "123456".
(Note)
Press MODE three times. Press UP or DOWN to choose point table No. 1.
Press SET once.
Press SET once.
Setting of upper 3 digits Setting of lower 3 digits

Press MODE once.
Press SET once.
The screen flickers.
Press UP or DOWN to
change the setting.
Press SET once.
Enter the setting.
Press MODE once.
Press "UP" or "DOWN" after completion of the setting to return to the setting item screen. Further,
press "UP" and "DOWN" together to return to the point table No. display screen.
8 - 15
8.6 Parameter mode
POINT
To use the expansion parameters, change the parameter No. 19 (parameter
write inhibit) value. (Refer to section 5.1.1)
8.6.1 Parameter mode transition
After choosing the corresponding parameter mode with the "MODE" button, pressing the "UP" or "DOWN"
button changes the display as shown below.
To status display mode
MODE
Basic parameters Expansion parameters 1 Expansion parameters 2 Special parameters 1 Special parameter 2 Option unit parameter
Parameter No. 0 Parameter No. 20 Parameter No. 54 Parameter No. 78 Parameter No. 91 Parameter No. 100
UP
DOWN
The parameter whose abbreviation is marked * is made valid by switching power off, then on after
changing its setting. (Refer to section 6.1.2)
8 - 16
8.6.2 Operation example
(1) Parameter of 5 or less digits

The following example shows the operation procedure performed after power-on to change the home
position setting method (Parameter No.8) into the data setting type. Press "MODE" to switch to the
basic parameter screen.
Press MODE four times. Select parameter No.8 with UP or DOWN.
The parameter number is displayed.
Press UP or DOWN to change the number.
Press SET twice.

The set value of the specified parameter number flickers.
Press UP twice.
During flickering, the set value can be changed.
Use UP or DOWN .
( 2: Data setting type)
Press SET to enter.
To shift to the next parameter, press the "UP" or "DOWN" button.

When changing the parameter No.8 (home position return type) setting, change its set value, then
switch power off once and switch it on again to make the new value valid.
8 - 17
(2) Signed 5-digit parameter

The following example gives the operation procedure to change the home position return position data
(parameter No. 42) to "-12345".
(Note)
Press MODE three times. Press UP or DOWN to choose parameter No. 42.
Press SET once.
Setting of upper 1 digits Setting of lower 4 digits

Press MODE once.
Press SET once.
The screen flickers.
Press UP or DOWN to
change the setting.
Press SET once.
Enter the setting.
Press MODE once.
When changing the parameter No. 42 setting, change its set value, then switch power off once and
switch it on again to make the new value valid.
8 - 18
8.7 External I/O signal display
The ON/OFF states of the digital I/O signals connected to the servo amplifier can be confirmed.
(1) Operation
Call the display screen shown after power-on.
Using the "MODE" button, show the diagnostic screen.
Press UP once.
External I/O signal display screen
(2) Display definition

The segments of the seven-segment LEDs correspond to the pins.
CN1A CN1B CN1B CN1B CN1B CN1A CN1B CN1B CN1B CN1B
19 15 9 8 7 8 14 5 17 16
Input signals
Always lit
Output signals
CN1A CN1B CN1B CN1B CN1B CN1A CN1A

14 18 4 6 19 18 19
Lit: ON
Extinguished: OFF
The 7-segment LED shown above indicates ON/OFF.

Each segment at top indicates the input signal and each segment at bottom indicates the output
signal. The signals corresponding to the pins in the respective control modes are indicated below.
8 - 19
8.8 Output signal (DO) forced output
POINT
When the servo is used in a vertical lift application, turning on
Electromagnetic brake interlock (MBR) will release the electromagnetic
brake, causing a drop. Take drop preventive measures on the machine side.
The output signal can be forced on/off independently of the servo status. This function is used for output
signal wiring check, etc. This operation must be performed in the servo off state (RYn1 off).
Call the display screen shown after power-on.
Using the "MODE" button, show the diagnostic screen.
Press UP twice.
Press SET for more than 2 seconds.

Switch on/off the signal below the lit segment.
Always lit
Indicates the ON/OFF of the output signal. The correspondences
between segments and signals are as in the output signals of the
CN1A CN1B CN1B CN1B CN1B CN1A CN1A external I/O signal display.
14 18 4 6 19 18 19
(Lit: ON, extinguished: OFF)
Press MODE once.
The segment above CN1A-pin 18 is lit.
Press UP once.
CN1A-pin 18 is switched on.

(CN1A-pin 18-SG conduct.)
Press DOWN once.
CN1A-pin 18 is switched off.
8 - 20
8.9 Test operation mode
The test operation mode is designed to confirm servo operation and not to confirm
machine operation. In this mode, do not use the servo motor with the machine.
CAUTION Always use the servo motor alone.
If any operational fault has occurred, stop operation using the forced stop (EMG) .
POINT
The test operation mode cannot be used in the absolute position detection
system. Use it after choosing "Incremental system" in parameter No. 1.
The MR Configurator (servo configuration software) is required to perform
Test operation cannot be performed if the servo-on (RYn1) signal is not
turned OFF.
8.9.1 Mode change
Call the display screen shown after power-on. Choose jog operation/motor-less operation in the following
procedure. Using the "MODE" button, show the diagnostic screen.
Press UP three times. Press UP five times.
Press SET for more Press SET for more than 2s.
than 2s.
When this screen When this screen is displayed,
appears, jog feed can motor-less operation can be
be performed. performed.
Flickers in the test operation mode.
8 - 21
8.9.2 Jog operation
Jog operation can be performed when there is no command from the external command device.
(1) Operation
Connect EMG-SG to start jog operation and connect VDD-COM to use the internal power supply.
Hold down the "UP" or "DOWN" button to run the servo motor. Release it to stop. When using the MR
Configurator (servo configuration software), you can change the operation conditions. The initial
conditions and setting ranges for operation are listed below.
Item Initial setting Setting range

Speed [r/min] 200 0 to instantaneous permissible speed
Acceleration/deceleration time constant [ms] 1000 0 to 50000
How to use the buttons is explained below.
Button Description
Press to start CCW rotation.
"UP"
Release to stop.
Press to start CW rotation.
"DOWN"
Release to stop.
If the communication cable is disconnected during jog operation performed by using the MR
Configurator (servo configuration software), the servo motor will be decelerated to a stop.
(2) Status display

You can confirm the servo status during jog operation.
Pressing the "MODE" button in the jog operation-ready status calls the status display screen. With
this screen being shown, perform jog operation with the "UP" or "DOWN" button. Every time you press
the "MODE" button, the next status display screen appears, and on completion of a screen cycle,
pressing that button returns to the jog operation-ready status screen. For full information of the status
display, refer to section 8.2. In the test operation mode, you cannot use the "UP" and "DOWN" buttons
to change the status display screen from one to another.
(3) Termination of jog operation

To terminate the jog operation, switch power off.
8 - 22
8.9.3 Positioning operation
POINT
The MR Configurator (servo configuration software) is required to perform
Positioning operation can be performed once when there is no command from the external command
device.
(1) Operation
Connect EMG-SG to start positioning operation and connect VDD-COM to use the internal power
supply.
Pressing the "Forward" or "Reverse" button on the MR Configurator (servo configuration software)
starts the servo motor, which will then stop after moving the preset travel distance. You can change
the operation conditions on the MR Configurator (servo configuration software). The initial conditions
and setting ranges for operation are listed below.
Item Initial setting Setting range

Travel distance [pulse] 10000 0 to 9999999
Speed [r/min] 200 0 to instantaneous permissible speed
Acceleration/deceleration time constant [ms] 1000 0 to 50000
How to use the keys is explained below.
Key Description
"Forward" Press to start positioning operation CCW.
"Reverse" Press to start positioning operation CW.
Press during operation to make a temporary stop. Pressing
the "Pause" button again erases the remaining distance.
"Pause"
To resume operation, press the button that was pressed to
start the operation.
If the communication cable is disconnected during positioning operation, the servo motor will come to
a sudden stop.
(2) Status display

You can monitor the status display even during positioning operation.
(3) Termination of positioning operation

To terminate the positioning operation, switch power off.
8 - 23
8.9.4 Motor-less operation
Without connecting the servo motor, you can provide output signals or monitor the status display as if the
servo motor is running in response to external input signals. This operation can be used to check the
sequence of a host programmable controller or the like.
(1) Operation
After turning off the signal across SON-SG, choose motor-less operation. After that, perform external
operation as in ordinary operation.
(2) Status display

You can confirm the servo status during motor-less operation.
Pressing the "MODE" button in the motor-less operation-ready status calls the status display screen.
With this screen being shown, perform motor-less operation. Every time you press the "MODE" button,
the next status display screen appears, and on completion of a screen cycle, pressing that button
returns to the motor-less operation-ready status screen. For full information of the status display,
refer to section 8.2. In the test operation mode, you cannot use the "UP" and "DOWN" buttons to
change the status display screen from one to another.
(3) Termination of motor-less operation

To terminate the motor-less operation, switch power off.
8 - 24
9. GENERAL GAIN ADJUSTMENT
9.1 Different adjustment methods
9.1.1 Adjustment on a single servo amplifier
The gain adjustment in this section can be made on a single servo amplifier. For gain adjustment, first
execute auto tuning mode 1. If you are not satisfied with the results, execute auto tuning mode 2, manual
mode 1 and manual mode 2 in this order.
(1) Gain adjustment mode explanation
Parameter No. 3 Estimation of load inertia Automatically set

Gain adjustment mode Manually set parameters
setting moment ratio parameters
PG1 (parameter No. 7)
GD2 (parameter No. 34)
Auto tuning mode 1 PG2 (parameter No. 35) Response level setting of
010 Always estimated
(initial value) VG1 (parameter No. 36) parameter No. 3
VG2 (parameter No. 37)
VIC (parameter No. 38)
PG2 (parameter No. 35) GD2 (parameter No. 34)
Auto tuning mode 2 020 VG1 (parameter No. 36) Response level setting of
VG2 (parameter No. 37) parameter No. 3
PG2 (parameter No. 35) GD2 (parameter No. 34)
Manual mode 1 030 Fixed to parameter No.
VG1 (parameter No. 36) VG2 (parameter No. 37)
34 value
Manual mode 2 040
PG2 (parameter No. 35) PG1 (parameter No. 7)
Interpolation mode 000 Always estimated
VG2 (parameter No. 37) VG1 (parameter No. 36)
9- 1
(2) Adjustment sequence and mode usage

START
Usage
Interpolation Yes Used when you want to
made for 2 or more
axes? match the position gain
No Interpolation mode (PG1) between 2 or more
axes. Normally not used for
Operation other purposes.
Allows adjustment by
Auto tuning mode 1
merely changing the
response level setting.
Operation
First use this mode to make
adjustment.
Yes No
OK? OK? Used when the conditions of
auto tuning mode 1 are not
No Yes met and the load inertia
Auto tuning mode 2 moment ratio could not be
estimated properly, for
Operation example.
Yes
OK?
This mode permits
No adjustment easily with three
Manual mode 1 gains if you were not
satisfied with auto tuning
Operation results.
Yes
OK?
You can adjust all gains
No
manually when you want to
Manual mode 2 do fast settling or the like.
END
9.1.2 Adjustment using MR Configurator (servo configuration software)

This section gives the functions and adjustment that may be performed by using the servo amplifier with
the MR Configurator (servo configuration software) which operates on a personal computer.
Function Description Adjustment
With the machine and servo motor You can grasp the machine resonance frequency and
coupled, the characteristic of the determine the notch frequency of the machine
mechanical system can be measured by resonance suppression filter.
giving a random vibration command from You can automatically set the optimum gains in
Machine analyzer
the personal computer to the servo and response to the machine characteristic. This simple
measuring the machine response. adjustment is suitable for a machine which has large
machine resonance and does not require much settling
time.
Executing gain search under to-and-fro You can automatically set gains which make positioning
positioning command measures settling settling time shortest.
characteristic while simultaneously
Gain search
changing gains, and automatically
searches for gains which make settling
time shortest.
Response at positioning settling of a You can optimize gain adjustment and command
Machine simulation machine can be simulated from machine pattern on personal computer.
analyzer results on personal computer.
9- 2
9.2 Auto tuning
9.2.1 Auto tuning mode
The servo amplifier has a real-time auto tuning function which estimates the machine characteristic (load
inertia moment ratio) in real time and automatically sets the optimum gains according to that value. This
function permits ease of gain adjustment of the servo amplifier.
(1) Auto tuning mode 1

The servo amplifier is factory-set to the auto tuning mode 1.
In this mode, the load inertia moment ratio of a machine is always estimated to set the optimum gains
automatically.
The following parameters are automatically adjusted in the auto tuning mode 1.
Parameter No. Abbreviation Name

7 PG1 Position control gain 1
34 GD2 Ratio of load inertia moment to servo motor inertia moment
36 VG1 Speed control gain 1
38 VIC Speed integral compensation
POINT
The auto tuning mode 1 may not be performed properly if the following
conditions are not satisfied.
Time to reach 2000r/min is the acceleration/deceleration time constant of 5s or
less.
Speed is 150r/min or higher.
The ratio of load inertia moment to motor inertia moment is not more
than 100 times.
The acceleration/deceleration torque is 10% or more of the rated torque.
Under operating conditions which will impose sudden disturbance torque
during acceleration/deceleration or on a machine which is extremely loose,
auto tuning may not function properly, either. In such cases, use the auto
tuning mode 2 or manual mode 1,2 to make gain adjustment.
(2) Auto tuning mode 2

Use the auto tuning mode 2 when proper gain adjustment cannot be made by auto tuning mode 1.
Since the load inertia moment ratio is not estimated in this mode, set the value of a correct load
inertia moment ratio (parameter No. 34).
The following parameters are automatically adjusted in the auto tuning mode 2.

9- 3
9.2.2 Auto tuning mode operation
The block diagram of real-time auto tuning is shown below.
Load inertia
Automatic setting moment
Encoder
Command Control gains Current Servo
PG1,VG1 control motor
PG2,VG2,VIC
Current feedback
Set 0 or 1 to turn on. Real-time auto Position/speed

tuning section feedback
Load inertia
Gain
moment ratio
table Switch estimation section Speed feedback
Parameter No. 3 Parameter No. 34

Load inertia moment
ratio estimation value
First digit
Third digit Response level setting
Auto tuning selection
When a servo motor is accelerated/decelerated, the load inertia moment ratio estimation section always
estimates the load inertia moment ratio from the current and speed of the servo motor. The results of
estimation are written to parameter No. 34 (load inertia moment ratio). These results can be confirmed on
the status display screen of the servo amplifier display section.
If the value of the load inertia moment ratio is already known or if estimation cannot be made properly,
chose the "auto tuning mode 2" (parameter No.3: 2 ) to stop the estimation of the load inertia
moment ratio (Switch in above diagram turned off), and set the load inertia moment ratio (parameter No.
34) manually.
From the preset load inertia moment ratio (parameter No. 34) value and response level (The first digit of
parameter No. 3), the optimum control gains are automatically set on the basis of the internal gain tale.
The auto tuning results are saved in the EEP-ROM of the servo amplifier every 60 minutes since power-
on. At power-on, auto tuning is performed with the value of each control gain saved in the EEP-ROM
being used as an initial value.
POINT
If sudden disturbance torque is imposed during operation, the estimation
of the inertia moment ratio may malfunction temporarily. In such a case,
choose the "auto tuning mode 2" (parameter No. 3: 2 ) and set the
correct load inertia moment ratio in parameter No. 34.
When any of the auto tuning mode 1, auto tuning mode 2 and manual
mode 1 settings is changed to the manual mode 2 setting, the current
control gains and load inertia moment ratio estimation value are saved in
the EEP-ROM.
9- 4
9.2.3 Adjustment procedure by auto tuning
Since auto tuning is made valid before shipment from the factory, simply running the servo motor
automatically sets the optimum gains that match the machine. Merely changing the response level
setting value as required completes the adjustment. The adjustment procedure is as follows.
Auto tuning adjustment
Acceleration/deceleration repeated
Yes Load inertia moment ratio

estimation value stable?
No
Auto tuning
conditions not satisfied. No
(Estimation of load inertia
moment ratio is difficult)
Yes
Choose the auto tuning mode 2
(parameter No.3 : 2 ) and set
the load inertia moment ratio
(parameter No.34) manually.
Adjust response level setting

so that desired response is
achieved on vibration-free level.
Acceleration/deceleration repeated
Requested No
performance satisfied?
Yes
END
To manual mode
9- 5
9.2.4 Response level setting in auto tuning mode
Set the response (The first digit of parameter No.3) of the whole servo system. As the response level
setting is increased, the track ability and settling time for a command decreases, but a too high response
level will generate vibration. Hence, make setting until desired response is obtained within the vibration-
free range.
If the response level setting cannot be increased up to the desired response because of machine resonance
beyond 100Hz, adaptive vibration suppression control (parameter No. 63) or machine resonance
suppression filter (parameter No. 61 62) may be used to suppress machine resonance. Suppressing
machine resonance may allow the response level setting to increase. Refer to section 10.2 for the setting of
machine resonance suppression filter, and to section 10.3 for the setting of adaptive vibration suppression
control.
Parameter No. 3
Auto tuning response level setting

Gain adjustment mode selection
Machine characteristic
Response level setting Machine resonance
Machine rigidity Guideline of corresponding machine
frequency guideline
1 Low 15Hz
2 20Hz
3 25Hz
Large conveyor
4 30Hz
5 35Hz
6 45Hz Arm robot
7 55Hz
General machine
8 Middle 70Hz
tool conveyor
9 85Hz Precision
A 105Hz working
machine
B 130Hz
Inserter
C 160Hz
Mounter
D 200Hz Bonder
E 240Hz
F High 300Hz
9- 6
9.3 Manual mode 1 (simple manual adjustment)
If you are not satisfied with the adjustment of auto tuning, you can make simple manual adjustment with
three parameters.
9.3.1 Operation of manual mode 1
In this mode, setting the three gains of position control gain 1 (PG1), speed control gain 2 (VG2) and
speed integral compensation (VIC) automatically sets the other gains to the optimum values according to
these gains.
GD2
User setting
PG1
PG2
VG2
Automatic setting VG1
VIC
Therefore, you can adjust the model adaptive control system in the same image as the general PI control
system (position gain, speed gain, speed integral time constant). Here, the position gain corresponds to
PG1, the speed gain to VG2 and the speed integral time constant to VIC. When making gain adjustment
in this mode, set the load inertia moment ratio (parameter No. 34) correctly.
9.3.2 Adjustment by manual mode 1
POINT
If machine resonance occurs, adaptive vibration suppression control
(parameter No. 63) or machine resonance suppression filter (parameter No.
61 62) may be used to suppress machine resonance. (Refer to section 10.2,
10.3.)
(1) For speed control

(a) Parameters
The following parameters are used for gain adjustment:
(b) Adjustment procedure

Step Operation Description
Set an estimated value to the ratio of load inertia moment to servo
1
motor inertia moment (parameter No. 34).
Increase the speed control gain 2 (parameter No. 37) within the Increase the speed control gain.
2 vibration- and unusual noise-free range, and return slightly if vibration
takes place.
Decrease the speed integral compensation (parameter No. 38) within Decrease the time constant of the speed
3
the vibration-free range, and return slightly if vibration takes place. integral compensation.
If the gains cannot be increased due to mechanical system resonance or Suppression of machine resonance.
the like and the desired response cannot be achieved, response may be Refer to section 10.2, 10.3.
4 increased by suppressing resonance with adaptive vibration
suppression control or machine resonance suppression filter and then
executing steps 2 and 3.
While checking the settling characteristic and rotational status, fine- Fine adjustment
5
adjust each gain.
9- 7
(c) Adjustment description

1) Speed control gain 2 (parameter No. 37)
This parameter determines the response level of the speed control loop. Increasing this value
enhances response but a too high value will make the mechanical system liable to vibrate. The
actual response frequency of the speed loop is as indicated in the following expression:
Speed loop response Speed control gain 2 setting
frequency(Hz) (1 ratio of load inertia moment to servo motor inertia moment) 2
2) Speed integral compensation (VIC: parameter No. 38)

To eliminate stationary deviation against a command, the speed control loop is under
proportional integral control. For the speed integral compensation, set the time constant of this
integral control. Increasing the setting lowers the response level. However, if the load inertia
moment ratio is large or the mechanical system has any vibratory element, the mechanical
system is liable to vibrate unless the setting is increased to some degree. The guideline is as
indicated in the following expression:
Speed integral compensation 2000 to 3000
setting(ms) Speed control gain 2 setting/ (1 ratio of load inertia moment to
servo motor inertia moment setting 0.1)
(2) For position control

(a) Parameters
The following parameters are used for gain adjustment:
(b) Adjustment procedure

Set an estimated value to the ratio of load inertia moment to servo
1
motor inertia moment (parameter No. 34).
Set a slightly smaller value to the position control gain 1 (parameter
2
No. 7).
Increase the speed control gain 2 (parameter No. 37) within the Increase the speed control gain.
3 vibration- and unusual noise-free range, and return slightly if vibration
takes place.
Decrease the speed integral compensation (parameter No. 38) within Decrease the time constant of the speed
4
the vibration-free range, and return slightly if vibration takes place. integral compensation.
5 Increase the position control gain 1 (parameter No. 7). Increase the position control gain.
If the gains cannot be increased due to mechanical system resonance or Suppression of machine resonance.
the like and the desired response cannot be achieved, response may be Refer to section 10.2, 10.3.
6 increased by suppressing resonance with adaptive vibration
suppression control or machine resonance suppression filter and then
executing steps 3 to 5.
While checking the settling characteristic and rotational status, fine- Fine adjustment
7
adjust each gain.
9- 8
(c) Adjustment description

1) Position control gain 1 (parameter No. 7)
This parameter determines the response level of the position control loop. Increasing position
control gain 1 improves track ability to a position command but a too high value will make
overshooting liable to occur at the time of settling.
Position control
gain 1 guideline
Speed control gain 2 setting
(1 ratio of load inertia moment to servo motor inertia moment)
( 13 to 15 )
2) Speed control gain 2 (VG2: parameter No. 37)
This parameter determines the response level of the speed control loop. Increasing this value
enhances response but a too high value will make the mechanical system liable to vibrate. The
actual response frequency of the speed loop is as indicated in the following expression:
Speed loop response Speed control gain 2 setting
frequency(Hz) (1 ratio of load inertia moment to servo motor inertia moment) 2
3) Speed integral compensation (parameter No. 38)

To eliminate stationary deviation against a command, the speed control loop is under
proportional integral control. For the speed integral compensation, set the time constant of this
integral control. Increasing the setting lowers the response level. However, if the load inertia
moment ratio is large or the mechanical system has any vibratory element, the mechanical
system is liable to vibrate unless the setting is increased to some degree. The guideline is as
indicated in the following expression:
Speed integral 2000 to 3000
compensation setting(ms) Speed control gain 2 setting/ (1 ratio of load inertia moment to
servo motor inertia moment 2 setting 0.1)
9- 9
9.4 Interpolation mode
The interpolation mode is used to match the position control gains of the axes when performing the
interpolation operation of servo motors of two or more axes for an X-Y table or the like. In this mode, the
position control gain 2 and speed control gain 2 which determine command track ability are set manually
and the other parameter for gain adjustment are set automatically.
(1) Parameter
(a) Automatically adjusted parameters
The following parameters are automatically adjusted by auto tuning.
(b) Manually adjusted parameters

The following parameters are adjustable manually.
(2) Adjustment procedure

Set 15Hz (parameter No. 3: 010 ) as the machine resonance frequency of response
1 Select the auto tuning mode 1.
in the auto tuning mode 1.
During operation, increase the response level setting (parameter No. 2), and Adjustment in auto tuning mode
2
return the setting if vibration occurs. 1.
Check the values of position control gain 1 (parameter No. 7) and speed control
3 Check the upper setting limits.
gain 1 (parameter No. 36).
4 Set the interpolation mode (parameter No. 3: 000 ). Select the interpolation mode.
Set the position control gain 1 of all the axes to be interpolated to the same
5 value. At that time, adjust to the setting value of the axis, which has the Set position control gain 1.
smallest position control gain 1.
Using the speed control gain 1 value checked in step 3 as the guideline of the
6 upper limit, look at the rotation status and set in speed control gain 1 the value Set speed control gain 1.
three or more times greater than the position control gain 1 setting.
Looking at the interpolation characteristic and rotation status, fine-adjust the
7 Fine adjustment.
gains and response level setting.
(3) Adjustment description

(a) Position control gain 1 (parameter No. 7)
This parameter determines the response level of the position control loop. Increasing position
control gain 1 improves track ability to a position command but a too high value will make
overshooting liable to occur at the time of settling. The droop pulse value is determined by the
following expression.
Rotation speed (r/min) 131,072(pulse)
Droop pulse value (pulse)
Position control gain 1 setting
(b) Speed control gain 1 (parameter No. 36)
Set the response level of the speed loop of the model. Make setting using the following expression
as a guideline.
Speed control gain 1 setting Position control gain 1 setting 3
9 - 10
9.5 Differences in auto tuning between MELSERVO-J2 and MELSERVO-J2-Super
9.5.1 Response level setting
To meet higher response demands, the MELSERVO-J2-Super series has been changed in response level
setting range from the MELSERVO-J2 series. The following table lists comparison of the response level
setting.
Parameter No. 3
Auto tuning response level setting
MELSERVO-J2 series MELSERVO-J2-Super series

Response level setting Machine resonance frequency Response level setting Machine resonance frequency guideline
1 15Hz
1 20Hz 2 20Hz
3 25Hz
4 30Hz
5 35Hz
2 40Hz 6 45Hz
7 55Hz
3 60Hz 8 70Hz
4 80Hz 9 85Hz
5 100Hz A 105Hz
B 130Hz
C 160Hz
D 200Hz
E 240Hz
F 300Hz
Note that because of a slight difference in gain adjustment pattern, response may not be the same if the
resonance frequency is set to the same value.
9.5.2 Auto tuning selection
The MELSERVO-J2-Super series has an addition of the load inertia moment ratio fixing mode. It also has
the addition of the manual mode 1 which permits manual adjustment with three parameters.
Parameter No. 3

Gain adjustment mode Remarks
MELSERVO-J2 series MELSERVO-J2-Super series
Interpolation mode 0 0 Position control gain 1 is fixed.
Auto tuning mode 1 1 1 Ordinary auto tuning
Estimation of load inertia moment
Auto tuning
Auto tuning mode 2 2 ratio stopped.
Response level setting valid.
Auto tuning Manual mode 1 3 Simple manual adjustment
invalid Manual mode 2 2 4 Manual adjustment of all gains
9 - 11
MEMO
9 - 12
10. SPECIAL ADJUSTMENT FUNCTIONS
POINT
The functions given in this chapter need not be used generally. Use them
if you are not satisfied with the machine status after making adjustment
in the methods in chapter 9.
If a mechanical system has a natural resonance point, increasing the servo system response may cause
the mechanical system to produce resonance (vibration or unusual noise) at that resonance frequency.
Using the machine resonance suppression filter and adaptive vibration suppression control functions can
suppress the resonance of the mechanical system.
10.1 Function block diagram
Speed Parameter Parameter Parameter Parameter Current

control No.61 No.63 No.62 No.63 command
00 0 00 Low-pass 0 Servo
filter motor
Machine resonance Machine resonance 1 Encoder

suppression filter 1 except 00 suppression filter 2 except 00
Adaptive vibration
suppression control 1 or 2
10.2 Machine resonance suppression filter
(1) Function
The machine resonance suppression filter is a filter function (notch filter) which decreases the gain of
the specific frequency to suppress the resonance of the mechanical system. You can set the gain
decreasing frequency (notch frequency) and gain decreasing depth.
Mechanical Machine resonance point

system
response
Frequency
Notch
depth
Frequency
Notch frequency
10 - 1
You can use the machine resonance suppression filter 1 (parameter No. 61) and machine resonance
suppression filter 2 (parameter No. 62) to suppress the vibration of two resonance frequencies. Note
that if adaptive vibration suppression control is made valid, the machine resonance suppression filter
1 (parameter No. 61) is made invalid.
Machine resonance point
Mechanical
system
response
Frequency
Notch
depth
Frequency
Parameter No. 61 Parameter No. 62
POINT
The machine resonance suppression filter is a delay factor for the servo
system. Hence, vibration may increase if you set a wrong resonance
frequency or a too deep notch.
(2) Parameters
(a) Machine resonance suppression filter 1 (parameter No. 61)
Set the notch frequency and notch depth of the machine resonance suppression filter 1 (parameter
No. 61)
When you have made adaptive vibration suppression control selection (parameter No. 63) "valid" or
"held", make the machine resonance suppression filter 1 invalid (parameter No. 61: 0000).
Parameter No. 61
Notch frequency
Setting Setting Setting Setting
Frequency Frequency Frequency Frequency
value value value value
00 Invalid 08 562.5 10 281.3 18 187.5
01 4500 09 500 11 264.7 19 180
02 2250 0A 450 12 250 1A 173.1
03 1500 0B 409.1 13 236.8 1B 166.7
04 1125 0C 375 14 225 1C 160.1
05 900 0D 346.2 15 214.3 1D 155.2
06 750 0E 321.4 16 204.5 1E 150
07 642.9 0F 300 17 195.7 1F 145.2
Notch depth
Setting
value Depth (Gain)
0 Deep ( 40dB)
1 ( 14dB)
2 ( 8dB)
3 Shallow( 4dB)
10 - 2
POINT
If the frequency of machine resonance is unknown, decrease the notch
frequency from higher to lower ones in order. The optimum notch
frequency is set at the point where vibration is minimal.
A deeper notch has a higher effect on machine resonance suppression but
increases a phase delay and may increase vibration.
The machine characteristic can be grasped beforehand by the machine
analyzer on the MR Configurator (servo configuration software). This
allows the required notch frequency and depth to be determined.
Resonance may occur if parameter No. 61 62 is used to select a close
notch frequency and set a deep notch.
(b) Machine resonance suppression filter 2 (parameter No. 62)

The setting method of machine resonance suppression filter 2 (parameter No. 62) is the same as
that of machine resonance suppression filter 1 (parameter No. 61). However, the machine
resonance suppression filter 2 can be set independently of whether adaptive vibration suppression
control is valid or invalid.
10.3 Adaptive vibration suppression control
(1) Function
Adaptive vibration suppression control is a function in which the servo amplifier detects machine
resonance and sets the filter characteristics automatically to suppress mechanical system vibration.
Since the filter characteristics (frequency, depth) are set automatically, you need not be conscious of
the resonance frequency of a mechanical system. Also, while adaptive vibration suppression control is
valid, the servo amplifier always detects machine resonance, and if the resonance frequency changes,
it changes the filter characteristics in response to that frequency.
Machine resonance point Machine resonance point
Mechanical Mechanical
system system
response response
Frequency Frequency
Notch Notch
depth depth
Frequency Frequency
Notch frequency Notch frequency
When machine resonance is large and frequency is low When machine resonance is small and frequency is high
POINT
The machine resonance frequency which adaptive vibration suppression
control can respond to is about 150 to 500Hz. Adaptive vibration
suppression control has no effect on the resonance frequency outside this
range. Use the machine resonance suppression filter for the machine
resonance of such frequency.
Adaptive vibration suppression control may provide no effect on a
mechanical system which has complex resonance characteristics or which
has too large resonance.
Under operating conditions in which sudden disturbance torque is imposed
during operation, the detection of the resonance frequency may malfunction
temporarily, causing machine vibration. In such a case, set adaptive
vibration suppression control to be "held" (parameter No. 63: 2 ) to fix
the characteristics of the adaptive vibration suppression control filter.
10 - 3
(2) Parameters
The operation of adaptive vibration suppression control selection (parameter No.63).
Parameter No. 63
Adaptive vibration suppression control selection

Choosing "valid" or "held" in adaptive vibration suppression
control selection makes the machine resonance suppression
filter 1 (parameter No. 61) invalid.
0: Invalid
1: Valid
Machine resonance frequency is always detected to
generate the filter in response to resonance, suppressing
machine vibration.
2: Held
Filter characteristics generated so far is held, and detection of
machine resonance is stopped.
Adaptive vibration suppression control sensitivity selection
Set the sensitivity of detecting machine resonance.
0: Normal
1: Large sensitivity
POINT
Adaptive vibration suppression control is factory-set to be invalid
(parameter No. 63: 0000).
The filter characteristics generated are saved in the EEP-ROM every 60
minutes since power-on. At next power-on, vibration suppression control is
performed with this data saved in the EEP-ROM being used as an initial
value.
Setting the adaptive vibration suppression control sensitivity can change
the sensitivity of detecting machine resonance. Setting of "large sensitivity"
detects smaller machine resonance and generates a filter to suppress
machine vibration. However, since a phase delay will also increase, the
response of the servo system may not increase.
10.4 Low-pass filter
(1) Function
When a ballscrew or the like is used, resonance of high frequency may occur as the response of the
servo system is increased. To prevent this, the low-pass filter is factory-set to be valid for a torque
command. The filter frequency of this low-pass filter is automatically adjusted to the value in the
following expression:
Speed control gain 2 setting 10
Filter frequency(Hz)
2 (1 Ratio of load inertia moment to servo motor inertia moment setting 0.1)
(2) Parameter
Set the operation of the low-pass filter (parameter No. 63.)
Parameter No. 63
Low-pass filter selection

0: Valid (automatic adjustment) initial value
1: Invalid
POINT
In a mechanical system where rigidity is extremely high and resonance is
difficult to occur, setting the low-pass filter to be "invalid" may increase
the servo system response to shorten the settling time.
10 - 4
10.5 Gain changing function
This function can change the gains. You can change between gains during rotation and gains during stop
or can use an external signal to change gains during operation.
10.5.1 Applications
This function is used when:

(1) You want to increase the gains during servo lock but decrease the gains to reduce noise during rotation.
(2) You want to increase the gains during settling to shorten the stop settling time.
(3) You want to change the gains using an external signal to ensure stability of the servo system since the
load inertia moment ratio varies greatly during a stop (e.g. a large load is mounted on a carrier).
The valid control gains PG2, VG2, VIC and GD2 of the actual loop are changed according to the conditions
selected by gain changing selection CDP (parameter No. 68) and gain changing condition CDS (parameter
No. 69).
CDP
Parameter No.68
External signal
CDP
Command pulse
frequency
Droop pulses
Changing
Model speed
Comparator
CDS
Parameter No.69
GD2
Parameter No.34
Valid
GD2B GD2 value
Parameter No.64
PG2
Parameter No.35
Valid
PG2 PG2B PG2 value
100
VG2
Parameter No.37
Valid
VG2 VG2B VG2 value
100
VIC
Parameter No.38
Valid
VIC VICB VIC value
100
10 - 5
10.5.3 Parameters
When using the gain changing function, always set " 4 " in parameter No.3 (auto tuning) to choose
the manual mode of the gain adjustment modes. The gain changing function cannot be used in the auto
tuning mode.
Parameter Abbrev-
Name Unit Description
No. iation
7 PG1 Position control gain 1 rad/s Position and speed gains of a model used to set the response
36 VG1 Speed control gain 1 rad/s level to a command. Always valid.
Ratio of load inertia moment to 0.1 Control parameters before changing
34 GD2
servo motor inertia moment times
35 PG2 Position control gain 2 rad/s
37 VG2 Speed control gain 2 rad/s
38 VIC Speed integral compensation ms
Ratio of load inertia moment to 0.1 Used to set the ratio of load inertia moment to servo motor
64 GD2B
servo motor inertia moment 2 times inertia moment after changing.
Position control gain 2 changing Used to set the ratio (%) of the after-changing position
65 PG2B %
ratio control gain 2 to position control gain 2.
Speed control gain 2 changing Used to set the ratio (%) of the after-changing speed control
66 VG2B %
ratio gain 2 to speed control gain 2.
Speed integral compensation Used to set the ratio (%) of the after-changing speed integral
67 VICB %
changing ratio compensation to speed integral compensation.
68 CDP Gain changing selection Used to select the changing condition.
kpps Used to set the changing condition values.
69 CDS Gain changing condition pulse
r/min
You can set the filter time constant for a gain change at
70 CDT Gain changing time constant ms
changing.
10 - 6
(1) Parameters No. 7, 34 to 38

These parameters are the same as in ordinary manual adjustment. Gain changing allows the values of
ratio of load inertia moment to servo motor inertia moment, position control gain 2, speed control gain
2 and speed integral compensation to be changed.
(2) Ratio of load inertia moment to servo motor inertia moment 2 (parameter No. 64)
Set the ratio of load inertia moment to servo motor inertia moment after changing. If the load inertia
moment ratio does not change, set it to the same value as ratio of load inertia moment to servo motor
inertia moment (parameter No. 34).
(3) Position control gain 2 changing ratio (parameter No. 65), speed control gain 2 changing ratio (parameter
No. 66), speed integral compensation changing ratio (parameter No. 67)
Set the values of after-changing position control gain 2, speed control gain 2 and speed integral
compensation in ratio (%). 100% setting means no gain change.
For example, at the setting of position control gain 2 100, speed control gain 2 2000, speed integral
compensation 20 and position control gain 2 changing ratio 180%, speed control gain 2 changing
ratio 150% and speed integral compensation changing ratio 80%, the after-changing values are as
follows:
Position control gain 2 Position control gain 2 Position control gain 2 changing ratio /100 180rad/s
Speed control gain 2 Speed control gain 2 Speed control gain 2 changing ratio /100 3000rad/s
Speed integral compensation Speed integral compensation Speed integral compensation changing
ratio /100 16ms
(4) Gain changing selection (parameter No. 68)

Used to set the gain changing condition. Choose the changing condition in the first digit. If you set "1"
here, you can use the gain changing (RY (n 2) 8) external input signal for gain changing. The gain
changing signal (RY (n 2) 8) can be assigned to input signals the pins using the MR Configurator
(servo configuration software).
Parameter No. 68
Gain changing selection

Gains are changed in accordance with the settings of
parameters No. 64 to 67 under any of the following conditions:
0: Invalid
1: Gain changing (RY (n 2) 8) input is ON
2: Command frequency is equal to higher than parameter No. 69 setting
3: Droop pulse value is equal to higher than parameter No. 69 setting
4: Servo motor speed is equal to higher than parameter No. 69 setting
(5) Gain changing condition (parameter No. 69)

When you selected "command frequency", "droop pulses" or "servo motor speed" in gain changing
selection (parameter No.68), set the gain changing level.
The setting unit is as follows:
Gain changing condition Unit

Command frequency kpps
Droop pulses pulse
Servo motor speed r/min
(6) Gain changing time constant (parameter No. 70)

You can set the primary delay filter to each gain at gain changing. This parameter is used to suppress
shock given to the machine if the gain difference is large at gain changing, for example.
10 - 7
10.5.4 Gain changing operation
This operation will be described by way of setting examples.
(1) When you choose changing by external input

(a) Setting
Parameter No. Abbreviation Name Setting Unit

Ratio of load inertia moment to
34 GD2 40 0.1 times
servo motor inertia moment
64 GD2B 100 0.1 times
servo motor inertia moment 2
Position control gain 2
65 PG2B 70 %
changing ratio
Speed control gain 2 changing
66 VG2B 133 %
ratio
Speed integral compensation
67 VICB 250 %
changing ratio
0001
68 CDP Gain changing selection (Changed by ON/OFF of
pin CN1A-8)
(b) Changing operation
Gain changing OFF ON OFF

(CDP)
After-changing gain
Change of Before-changing gain

each gain CDT 100ms
Position control gain 1 100

Speed control gain 1 1000
4.0 10.0 4.0
to servo motor inertia moment
Position control gain 2 120 84 120
Speed control gain 2 3000 4000 3000
Speed integral compensation 20 50 20
10 - 8
(2) When you choose changing by droop pulses

(a) Setting
Parameter No. Abbreviation Name Setting Unit

34 GD2 40 0.1 times
servo motor inertia moment
64 GD2B 100 0.1 times
servo motor inertia moment 2
Position control gain 2
65 PG2B 70 %
changing ratio
Speed control gain 2 changing
66 VG2B 133 %
ratio
Speed integral compensation
67 VICB 250 %
changing ratio
0003
68 CDP Gain changing selection
(Changed by droop pulses)
69 CDS Gain changing condition 50 pulse
(b) Changing operation

Command pulse
Droop pulses
CDS
Droop pulses [pulses] 0
CDS
After-changing gain
Before-changing gain
Change of each gain
CDT 100ms
Position control gain 1 100

Speed control gain 1 1000
4.0 10.0 4.0 10.0
to servo motor inertia moment
Position control gain 2 120 84 120 84
Speed control gain 2 3000 4000 3000 4000
Speed integral compensation 20 50 20 50
10 - 9
MEMO
10 - 10
11. INSPECTION
11. INSPECTION
Before starting maintenance and/or inspection, turn off the power and wait for 15
minutes or more until the charge lamp turns off. Then, confirm that the voltage
between P and N is safe with a voltage tester and others. Otherwise, an electric
shock may occur. In addition, always confirm from the front of the servo amplifier
WARNING whether the charge lamp is off or not.
Any person who is involved in inspection should be fully competent to do the work.
Otherwise, you may get an electric shock. For repair and parts replacement,
contact your safes representative.
POINT
Do not test the servo amplifier with a megger (measure insulation
resistance), or it may become faulty.
Do not disassemble and/or repair the equipment on customer side.
(1) Inspection
It is recommended to make the following checks periodically.
(a) Check for loose terminal block screws. Retighten any loose screws.
(b) Check the cables and the like for scratches and cracks. Perform periodic inspection according to
operating conditions.
(2) Life
The following parts must be changed periodically as listed below. If any part is found faulty, it must be
changed immediately even when it has not yet reached the end of its life, which depends on the
operating method and environmental conditions. For parts replacement, please contact your sales
representative.
Part name Life guideline

Smoothing capacitor 10 years
Number of power-on and number of forced
Relay
Servo amplifier stop times : 100,000 times
Cooling fan 10,000 to 30,000hours (2 to 3 years)
Absolute position battery Refer to section 5.5
(a) Smoothing capacitor

Affected by ripple currents, etc. and deteriorates in characteristic. The life of the capacitor greatly
depends on ambient temperature and operating conditions. The capacitor will reach the end of its
life in 10 years of continuous operation in normal air-conditioned environment.
(b) Relays
Their contacts will wear due to switching currents and contact faults occur. Relays reach the end of
their life when the cumulative number of power-on and forced stop times is 100,000, which depends
on the power supply capacity.
(c) Servo amplifier cooling fan
The cooling fan bearings reach the end of their life in 10,000 to 30,000 hours. Normally, therefore,
the fan must be changed in a few years of continuous operation as a guideline.
It must also be changed if unusual noise or vibration is found during inspection.
11 - 1
11. INSPECTION
MEMO
11 - 2
12. TROUBLESHOOTING
12. TROUBLESHOOTING
12.1 Trouble at start-up
Excessive adjustment or change of parameter setting must not be made as it will

CAUTION make operation instable.
POINT
Using the MR Configurator (servo configuration software), you can refer to
unrotated servo motor reasons, etc.
The following faults may occur at start-up. If any of such faults occurs, take the corresponding action.
No. Start-up sequence Fault Investigation Possible cause Reference

1 Power on LED is not lit. Not improved if connectors 1. Power supply voltage fault
LED flickers. CN1A, CN1B, CN2 and CN3 2. Servo amplifier is faulty.
are disconnected.
Improved when connectors Power supply of CN1 cabling is
CN1A and CN1B are shorted.
disconnected.
Improved when connector 1. Power supply of encoder
CN2 is disconnected. cabling is shorted.
2. Encoder is faulty.
Improved when connector Power supply of CN3 cabling is
CN3 is disconnected. shorted.
Ab is displayed on Confirm the connection 1. MR-J2S-T01 is not
LED. between connecters CN3 and connected.
CN30 of MR-J2S-T01. 2. CN3 cable breakage.
Alarm occurs. Refer to section 12.4 and remove cause. Section 12.4
2 Switch on servo-on Alarm occurs. Refer to section 12.4 and remove cause. Section 12.4
(RYn0) signal. Servo motor shaft is 1. Check the display to see if 1. Servo-on (RYn0) is not Section 8.3.2
not servo-locked the servo amplifier is input. (Wiring mistake)
(is free). ready to operate. 2. 24VDC power is not
2. Check the external I/O supplied to COM.
signal indication to see if
the servo-on (RYn0)
signal is ON.
3 Gain adjustment Rotation ripples Make gain adjustment in the Gain adjustment fault Chapter 9
(speed fluctuations) following procedure.
are large at low 1. Increase the auto tuning
speed. response level.
2. Repeat acceleration and
deceleration several times
to complete auto tuning.
Large load inertia If the servo motor may be Gain adjustment fault Chapter 9
moment causes the run with safety, repeat
servo motor shaft to acceleration and
oscillate side to side. deceleration several times to
complete auto tuning.
4 Cyclic operation Position shift occurs Confirm the cumulative Pulse counting error, etc.
command pulses, cumulative due to noise.
feedback pulses and actual
servo motor position.
12 - 1
12. TROUBLESHOOTING
12.2 Operation at error occurrence

An error occurring during operation will result in any of the statuses indicated in the following table.
Operation mode
Error location Description
Test operation CC-Link operation
Servo operation Stop Stop
Servo side alarm
Data communication between servo amplifier and CC-Link unit Continued Continued
occurrence
CC-Link data communication Continued Continued
Option unit
Data communication between servo amplifier and CC-Link unit Stop Stop
communication error
CC-Link data communication Stop Stop
CC-Link
communication error
Servo operation Continued Stop
Programmable
controller error/STOP
Servo operation Stop Continued
Servo side warning
occurrence
CC-Link data communication Continued Continued
12 - 2
12. TROUBLESHOOTING
12.3 CC-Link communication error

This section gives the definitions of the indications given in the communication alarm display section.
The MR-J2S-T01 option unit has six LED indications.
L.RUN : Lit at normal receive of refresh data. Extinguished when data is not received for a given period of
time.
SD : Lit when send data is "0".
RD : Lit when the carrier of receive data is detected.
L.ERR : Lit when the data addressed to the host is in CRC or abort error.
S.ERR : Lit when the servo amplifier is in an alarm status.
WD : Lit when the MR-J2S-T01 option unit is in CPU fault.
(Note) Communication alarm display LED
Operation
L.RUN SD RD L.ERR
Normal communication is made, but a CRC error sometimes occurs due to noise.
Normal communication
Hardware fault
Hardware fault
Receive data results in CRC error, disabling a response.
Data does not reach the host.
Hardware fault
Hardware fault
Polling response is made, but refresh receive is in CRC error.
Hardware fault
Hardware fault
Hardware fault
Data addressed to the host resulted in CRC error.
Data does not reach the host, or the data addressed to the host cannot be received due
to noise.
Hardware fault
Baud rate setting illegal
Station number setting illegal
Baud rate or station number setting changed midway (ERROR flickers for about 4s)
Data cannot be received due to power-off, power supply failure, open cable, etc.
WDT error occurrence (hardware fault)
Note. : Lit : Extinguished : Flicker
(Note)
Communication
Operation (Refer to the above for L.RUN, SD, RD and L.ERR.)
alarm display LED
S.ERR WD
Servo amplifier in normal status
Servo amplifier in alarm occurrence status
Option unit in normal status
Option unit in CPU fault status
Note. : Lit : Extinguished : Flicker : Indefinite
12.4 When alarm or warning has occurred
POINT
Configure up a circuit which will detect the trouble (RX(n+1)A or
RX(n+3)A) signal and turn off the servo-on (RYn0) at occurrence of an
alarm.
12 - 3
12. TROUBLESHOOTING
12.4.1 Alarms and warning list
When a fault occurs during operation, the corresponding alarm or warning is displayed. If any alarm or
warning has occurred, refer to section 12.4.2 or 12.4.3 and take the appropriate action. When an alarm
occurs, Trouble (RX(n+1)A or RX(n+3)A) turns ON.
After its cause has been removed, the alarm can be deactivated in any of the methods marked in the
alarm deactivation column.
Alarm deactivation
Display Name Press "SET" on
Power Alarm reset (RES)
current alarm
OFF ON signal
screen.
AL.10 Undervoltage
AL.12 Memory error 1
AL.13 Clock error
AL.16 Encoder error 1
AL.17 Board error
AL.1A Motor combination error
AL.20 Encoder error 2
AL.24 Main circuit error
AL.25 Absolute position erase
AL.30 Regenerative error (Note) (Note) (Note)
AL.31 Overspeed
Alarms
AL.32 Overcurrent
AL.33 Overvoltage
AL.37 Parameter error
AL.45 Main circuit device overheat (Note) (Note) (Note)
AL.46 Servo motor overheat (Note) (Note) (Note)
AL.50 Overload 1 (Note) (Note) (Note)
AL.51 Overload 2 (Note) (Note) (Note)
AL.52 Error excessive
AL.61 Home operation alarm
AL.72 Option unit communication error
AL.76 Option unit ID error
AL.8A Serial communication time-out error
AL.8D CC-Link alarm
AL.8E Serial communication error
88888 Watchdog
AL.90 Home position return incomplete
AL.92 Open battery cable warning
AL.96 Home position setting warning
AL.98 Software limit warning
AL.9D CC-Link warning 1
Warnings
AL.9E CC-Link warning 2 Removing the cause of occurrence deactivates the alarm
AL.9F Battery warning automatically.
AL.E0 Excessive regenerative warning
AL.E1 Overload warning
AL.E3 Absolute position counter warning
AL.E6 Servo forced stop warning
AL.E9 Main circuit off warning
Note. Deactivate the alarm about 30 minutes of cooling time after removing the cause of occurrence.
12 - 4
12. TROUBLESHOOTING
12.4.2 Remedies for alarms
When any alarm has occurred, eliminate its cause, ensure safety, then reset the
alarm, and restart operation. Otherwise, injury may occur.
CAUTION If an absolute position erase alarm (AL.25) occurred, always make home position
setting again. Otherwise, misoperation may occur.
As soon as an alarm occurs, turn off Servo-on (RYn0) and power off.
POINT
When any of the following alarms has occurred, always remove its cause
and allow about 30 minutes for cooling before resuming operation. If
operation is resumed by switching control circuit power off, then on to reset
the alarm, the servo amplifier and servo motor may become faulty.
Regenerative error (AL.30)
Overload 1 (AL.50)
Overload 2 (AL.51)
The alarm can be deactivated by switching power off, then on press the
"SET" button on the current alarm screen or by turning on the reset
(RY(n+1)A or RY(n+3)A). For details, refer to section 12.4.1.
When an alarm occurs, the trouble (RX(n+1)A or RX(n+3)A) switches on and the dynamic brake is
operated to stop the servo motor. At this time, the display indicates the alarm No.
The servo motor comes to a stop. Remove the cause of the alarm in accordance with this section. The MR
Configurator (servo configuration software) may be used to refer to the cause.
Display Name Definition Cause Action

AL.10 Undervoltage Power supply 1. Power supply voltage is low. Review the power supply.
voltage dropped. 2. There was an instantaneous
MR-J2S- CP-S084: control power failure of 60ms or
160VAC or less longer.
MR-J2S- CP1-S084: 3. Shortage of power supply capacity
83VAC or less caused the power supply voltage to
drop at start, etc.
4. The bus voltage dropped to the
following value or less.
MR-J2S- CP-S084: 200VDC
MR-J2S- CP1-S084: 158VDC
5. Faulty parts in the servo amplifier Change the servo amplifier.
Checking method
Alarm (AL.10) occurs if power is
switched on after disconnection
of all cables but the control
circuit power supply cables.
AL.12 Memory error 1 RAM, memory fault Faulty parts in the servo amplifier Change the servo amplifier.
AL.13 Clock error Printed board fault Checking method
Alarm (any of AL.12 and 13)
occurs if power is switched on
after disconnection of all cables
but the control circuit power
supply cables.
12 - 5
12. TROUBLESHOOTING

AL.15 Memory error 2 EEP-ROM fault 1. Faulty parts in the servo amplifier Change the servo amplifier.
Checking method
Alarm (AL.15)
occurs if power is switched on
after disconnection of all cables
but the control circuit power
supply cables.
2. The number of write times to EEP-

ROM exceeded 100,000.
AL.16 Encoder error 1 Communication 1. Encode connector (CN2) Connect correctly.
error occurred disconnected.
between encoder 2. Encoder fault Change the servo motor.
and servo amplifier 3. Encoder cable faulty Repair or change the cable.
(wire breakage or short)
AL.17 Board error CPU/parts fault 1. Faulty parts in the servo amplifier. Change the servo amplifier.
Checking method
of all cable but the control circuit
power supply cable.
The output 2. The wiring of U, V, W is Correctly connect the output terminals U,
terminals U, V, W of
the servo amplifier disconnected or not connected. V, W of the servo amplifier and the input
and the input terminals U, V, W of the servo motor.
terminals U, V, W of
the servo motor are
not connected.
AL.19 Memory error 3 ROM memory fault Faulty parts in the servo amplifier. Change the servo amplifier.
Checking method
of all cable but the control circuit
power supply cable.
AL.1A Motor Wrong combination Wrong combination of servo amplifier Use correct combination.
combination of servo amplifier and servo motor connected.
error and servo motor.
AL.20 Encoder error 2 Communication 1. Encoder connector (CN2) Connect correctly.
error occurred disconnected.
between encoder 2. Encoder fault Change the servo motor.
and servo amplifier.3. Encoder cable faulty Repair or change the cable.
(wire breakage or shorted)
Encoder detected 4. Excessive acceleration is occurred 1. Decrease the speed control gain 2.
acceleration error. due to oscillation and others. 2. Decrease the auto tuning response level.
AL.24 Main circuit Ground fault 1. Power input wires and servo motor Connect correctly.
error occurred at the power cables are in contact at main
servo motor power circuit terminal block (TE1).
(U,V and W phases) 2. Sheathes of servo motor power Change the cable.
of the servo cables deteriorated, resulting in
amplifier. ground fault.
3. Main circuit of servo amplifier Change the servo amplifier.
failed.
Checking method
AL.24 occurs if the servo is
switched on after disconnecting
the U, V, W power cables from
12 - 6
12. TROUBLESHOOTING

AL.25 Absolute Absolute position 1. Reduced voltage of super capacitor After leaving the alarm occurring for a few
position erase data in error in encoder minutes, switch power off, then on again.
Always make home position setting again.
2. Battery voltage low Change battery.
3. Battery cable or battery is faulty. Always make home position setting again.
Power was switched 4. Super capacitor of the absolute After leaving the alarm occurring for a few
on for the first time position encoder is not charged minutes, switch power off, then on again.
in the absolute Always make home position setting again.
position detection
system.
AL.30 Regenerative Permissible 1. Wrong setting of parameter No. 0 Set correctly.
error regenerative power 2. Built-in regenerative resistor or Connect correctly
of the built-in regenerative option is not
regenerative resistor connected.
or regenerative 3. High-duty operation or continuous 1. Reduce the frequency of positioning.
option is exceeded. regenerative operation caused the 2. Use the regenerative option of larger
permissible regenerative power of capacity.
the regenerative option to be 3. Reduce the load.
exceeded.
Checking method
Call the status display and check
the regenerative load ratio.
4. Power supply voltage is abnormal. Review power supply

MR-J2S- CP-S084:260VAC or
more
MR-J2S- CP1-S084:135VAC or
more
5. Built-in regenerative resistor or Change servo amplifier or regenerative
regenerative option faulty. option.
Regenerative 6. Regenerative transistor faulty. Change the servo amplifier.
transistor fault
Checking method
1) The regenerative option has
overheated abnormally.
2) The alarm occurs even after
removal of the built-in
regenerative resistor or
regenerative option.
AL.31 Overspeed Speed has exceeded 1. Input command pulse frequency Set command pulses correctly.
the instantaneous exceeded the permissible
permissible speed. instantaneous speed frequency.
2. Small acceleration/deceleration Increase acceleration/deceleration time
time constant caused overshoot to constant.
be large.
3. Servo system is instable to cause 1. Re-set servo gain to proper value.
overshoot. 2. If servo gain cannot be set to proper
value.
1) Reduce load inertia moment ratio; or
2) Reexamine acceleration/
deceleration time constant.
4. Electronic gear ratio is large. Set correctly.
(parameters No. 4, 5)
5. Encoder faulty. Change the servo motor.
12 - 7
12. TROUBLESHOOTING

AL.32 Overcurrent Current that flew is 1. Short occurred in servo amplifier Correct the wiring.
higher than the output phases U, V and W.
permissible current 2. Transistor (IPM) of the servo Change the servo amplifier.
of the servo amplifier faulty.
amplifier. (If the Checking method
alarm (AL.32) Alarm (AL.32) occurs if power is
occurs again when switched on after U,V and W
turning ON the are disconnected.
servo after resetting
3. Ground fault occurred in servo Correct the wiring.
the alarm by
amplifier output phases U, V and
turning OFF/ON the
W.
power when the
4. External noise caused the Take noise suppression measures.
alarm (AL.32) first
overcurrent detection circuit to
occurred, the
misoperate.
transistor (IPM,
IGBT) of the servo
amplifier may be at
fault. In the case, do
not repeat to turn
OFF/ON the power.
Check the transistor
with the checking
method of “Cause
2”.)
AL.33 Overvoltage Converter bus 1. Regenerative option is not used. Use the regenerative option.
voltage exceeded 2. Though the regenerative option is Make correct setting.
400VDC. used, the parameter No. 0 setting is
" 0 (not used)".
3. Lead of built-in regenerative 1. Change lead.
resistor or regenerative option is 2. Connect correctly.
open or disconnected.
4. Regenerative transistor faulty. Change servo amplifier
5. Wire breakage of built-in 1. For wire breakage of built-in
regenerative resistor or regenerative resistor, change servo
regenerative option. amplifier.
2. For wire breakage of regenerative
option, change regenerative option.
6. Capacity of built-in regenerative Add regenerative option or increase
resistor or regenerative option is capacity.
insufficient.
7. Power supply voltage high. Review the power supply.
8. The jumper across BUE-SD of the Fit the jumper across BUE-SD.
FR-BU2 brake unit is removed.
12 - 8
12. TROUBLESHOOTING

AL.37 Parameter Parameter setting is 1. Servo amplifier fault caused the Change the servo amplifier.
error wrong. parameter setting to be rewritten.
2. Regenerative option not used with Set parameter No.0 correctly.
servo amplifier was selected in
parameter No.0.
3. Value outside setting range has Set the parameter correctly.
been set in some parameter.
4. Value outside setting range has Set parameters No. 4, 5 correctly.
been set in electronic gear.
5. Opposite sign has been set in Set parameters No. 46 to 49 correctly.
software limit increasing side
(parameters No. 46, 47). Similarly,
opposite sign has been set in
software limit decreasing side
(parameters No. 48, 49).
6. Opposite sign has been set in Set parameters No. 50 to 53 correctly.
position range output address
increasing side (parameters No. 50,
51). Similarly, opposite sign has
been set in position range output
address decreasing side
(parameters No. 52, 53).
7. The number of write times to EEP- Change the servo amplifier.
ROM exceeded 100,000 due to
parameter write, etc.
AL.45 Main circuit Main circuit device 1. Servo amplifier faulty. Change the servo amplifier.
device overheat overheat 2. The power supply was turned on The drive method is reviewed.
and off continuously by overloaded
status.
3. Air cooling fan of servo amplifier 1. Exchange the cooling fan or the servo
stops. amplifier.
2. Reduce ambient temperature.
AL.46 Servo motor Servo motor 1. Ambient temperature of servo Review environment so that ambient
overheat temperature rise motor is over 40 (104 ). temperature is 0 to 40 (32 to 104 ).
actuated the 2. Servo motor is overloaded. 1. Reduce load.
thermal sensor. 2. Review operation pattern.
3. Use servo motor that provides larger
output.
3. Thermal sensor in encoder is faulty. Change servo motor.
12 - 9
12. TROUBLESHOOTING

AL.50 Overload 1 Load exceeded 1. Servo amplifier is used in excess of 1. Reduce load.
overload protection its continuous output current. 2. Review operation pattern.
characteristic of 3. Use servo motor that provides larger
servo amplifier. output.
2. Servo system is instable and 1. Repeat acceleration/
hunting. deceleration to execute auto tuning.
2. Change auto tuning response setting.
3. Set auto tuning to OFF and make gain
adjustment manually.
3. Machine struck something. 1. Review operation pattern.
2. Install limit switches.
4. Wrong connection of servo motor. Connect correctly.
Servo amplifier's output terminals
U, V, W do not match servo motor's
input terminals U, V, W.
Checking method
When the servo motor shaft is
rotated with the servo off, the
cumulative feedback pulses do
not vary in proportion to the
rotary angle of the shaft but the
indication skips or returns midway.
AL.51 Overload 2 Machine collision or 1. Machine struck something. 1. Review operation pattern.
the like caused max. 2. Install limit switches.
For the time of the 2. Wrong connection of servo motor. Connect correctly.
alarm occurrence, Servo amplifier's output terminals
refer to the section U, V, W do not match servo motor's
14.1. input terminals U, V, W.
3. Servo system is instable and 1. Repeat acceleration/deceleration to
hunting. execute auto tuning.
2. Change auto tuning response setting.
3. Set auto tuning to OFF and make gain
adjustment manually.
Checking method
When the servo motor shaft is
rotated with the servo off, the
cumulative feedback pulses do
not vary in proportion to the
rotary angle of the shaft but the
indication skips or returns midway.
12 - 10
12. TROUBLESHOOTING

AL.52 Error excessive The difference 1. Acceleration/deceleration time Increase the acceleration/deceleration
between the model constant is too small. time constant.
position and the 2. Internal torque limit 1 (parameter Increase the torque limit value.
actual servo motor No.28) is too small.
position exceeds 2.5 3. Motor cannot be started due to 1. Review the power supply capacity.
rotations. (Refer to torque shortage caused by power 2. Use servo motor which provides larger
the function block supply voltage drop. output.
diagram in section 4. Position control gain 1 (parameter Increase set value and adjust to ensure
1.1.2) No.7) value is small. proper operation.
5. Servo motor shaft was rotated by 1. When torque is limited, increase the
external force. limit value.
2. Reduce load.
3. Use servo motor that provides larger
output.
6. Machine struck something. 1. Review operation pattern.
2. Install limit switches.
7. Encoder faulty Change the servo motor.
8. Wrong connection of servo motor. Connect correctly.
Servo amplifier's output terminals
U, V, W do not match servo
motor's input terminals U, V, W.
AL.61 Home "1" or more has been Setting mistake of auxiliary function Set "0" to auxiliary function of point table
operation set to auxiliary of point table No. 31. No. 31.
alarm function of point
table No. 31.
AL.72 Option unit The option unit is 1. The option unit is not connected. Reconnect the option unit correctly.
communication not connected. 2. Option unit board fault. Change the option unit.
error 3. Cable between option unit and Change the cable.
servo amplifier is faulty.
AL.76 Option unit ID The servo amplifier The option unit not supported by the 1. Connect the option unit supported by
error is receiving an servo amplifier is connected. the servo amplifier.
unsupported ID. 2. Change the option unit.
AL.8A Serial RS-232C or RS-422 1. Communication cable breakage. Repair or change communication cable
communication communication 2. Communication cycle longer than Set correct value in parameter.
time-out error stopped for longer parameter No. 23 setting.
than the time set in 3. Wrong protocol. Correct protocol.
parameter No.23.
AL.8D CC-Link alarm Normal 1. The station number switch setting Set the station number to within the
communication with is 0 or not less than 65. range 1 to 64, and switch power on.
the master station 2. The baud rate switch setting is Set the switch to within the range 0 to 4.
cannot be made. outside the range 0 to 4.
3. The transmission status is Reexamine the wiring.
abnormal.
4. CC-Link twisted cable wiring 1. Repair or change the CC-Link twisted
incorrect. cable.
5. CC-Link twisted cable faulty. 2. Connect the cable or connector
6. The CC-Link connector has come correctly.
off.
7. The terminating resistor is not Connect the terminating resistor correctly.
connected.
8. Noise entered the CC-Link twisted
cable.
AL.8E Serial Serial 1. Communication cable fault Repair or change the cable.
communication communication error (Open cable or short circuit)
error occurred between
2. Communication device (e.g. Change the communication device (e.g.
servo amplifier and
personal computer) faulty personal computer).
communication
device (e.g. personal
computer).
12 - 11
12. TROUBLESHOOTING

88888 Watchdog CPU, parts faulty Fault of parts in servo amplifier Change servo amplifier.
Checking method
Alarm (88888) occurs if power is
of all cables but the control
circuit power supply cables.
12.4.3 Remedies for warnings
If an absolute position counter warning (AL.E3) has occurred, always perform

CAUTION home position setting again. Failure to do so can cause runaway.
POINT
When any of the following alarms has occurred, do not resume operation by
switching power of the servo amplifier OFF/ON repeatedly. The servo
amplifier and servo motor may become faulty. If the power of the servo
amplifier is switched OFF/ON during the alarms, allow more than 30
minutes for cooling before resuming operation.
Excessive regenerative warning (AL.E0)
Overload warning 1 (AL.E1)
The servo off status is established if a servo forced stop warning (AL.E6) or software limit warning
(AL.98) occurs. If any other warning occurs, operation can be continued but an alarm may take place or
proper operation may not be performed. Remove the cause of the warning according to this section. Use
the optional MR Configurator (servo configuration software) to refer to the cause of warning.

AL.90 Home position Positioning 1. Positioning operation was performed Perform home position return.
return incomplete operation was without home position return.
performed without
In incremental
home position
system
return.
Home position 2. Home position return speed could not Review home position return
return ended be decreased to creep speed. speed/creep speed/moving
abnormally. 3. Limit switch was actuated during home distance after proximity dog.
position return starting at other than
position beyond dog.
Positioning 1. Positioning operation was performed Perform home position setting.
operation was without home position setting.
performed without
In absolute position detection system
home position
setting.
Home position 2. Home position setting speed could not Review home position setting
setting ended be decreased to creep speed. speed/creep speed/moving
abnormally. 3. Limit switch was actuated during home distance after proximity dog.
position setting starting at other than
position beyond dog.
Operation was 4. Voltage drop in encoder After leaving the alarm

performed without (Battery disconnected.) occurring for a few minutes,
making home switch power off, then on again.
position setting Always make home position
while an absolute setting again.
position erase 5. Battery voltage low Change battery.
(AL.25) is being 6. Battery cable or battery is faulty. Always make home position
occurred. setting again.
AL.92 Open battery Absolute position 1. Battery cable is open. Repair cable or changed.
cable warning detection system battery 2. Battery voltage supplied for the servo Change battery.
voltage is low. amplifier to the encoder fell to about
3.2V or less.
(Detected with the encoder)
12 - 12
12. TROUBLESHOOTING

AL.96 Home position Home position setting 1. Droop pulses remaining are greater Remove the cause of droop pulse
setting warning could not be made. than the in-position range setting. occurrence
2. Command pulse entered after clearing Do not enter command pulse
of droop pulses. after clearing of droop pulses.
3. Creep speed high. Reduce creep speed.
AL.98 Software limit Software limit set in 1. Software limit was set within actual Set parameter No. 48 to 51
warning parameter is reached. operation range. correctly.
2. Point table of position data in excess of Set point table correctly.
software limit was executed.
3. Software limit was reached during JOG Perform operation within
operation or manual pulse generator software limit range.
operation.
AL.9D CC-Link warning The station number 1. The station number switch position was Return to the setting at power-
1 switch or baud rate changed from the setting at power-on. on.
switch position was 2. The baud rate switch position was
changed from the setting changed from the setting at power-on.
at power-on. 3. The occupied station count switch
position was changed from the setting
at power-on.
AL9E CC-Link warning Communication error of 1. The transmission status is abnormal. Take measures against noise.
2 cable 2. CC-Link twisted cable wiring incorrect. 1. Change the CC-Link twisted
3. CC-Link twisted cable faulty. cable.
4. The CC-Link connector has come off. 2. Connect the cable or
connector correctly.
5. The terminating resistor is not Connect the terminating
connected. resistor correctly.
6. Noise entered the CC-Link twisted
cable.
AL.9F Battery warning Voltage of battery for Battery voltage fell to 3.2VDC or less. Change the battery.
absolute position (Detected with the servo amplifier)
detection system reduced.
AL.E0 Excessive There is a possibility that Regenerative power increased to 85% or 1. Reduce frequency of
regenerative regenerative power may more of permissible regenerative power of positioning.
warning exceed permissible built-in regenerative resistor or 2. Change regenerative option
regenerative power of regenerative option. for the one with larger
built-in regenerative Checking method capacity.
resistor or regenerative Call the status display and check 3. Reduce load.
option. regenerative load ratio.
AL.E1 Overload There is a possibility that Load increased to 85% or more of overload Refer to AL.50, AL.51.
warning overload alarm 1 or 2 alarm 1 or 2 occurrence level.
may occur. Cause, checking method
Refer to AL.50,51.
AL.E3 Absolute position Absolute position encoder 1. Noise entered the encoder. Take noise suppression
counter warning pulses faulty. measures.
2. Encoder faulty. Change servo motor.
The multi-revolution 3. The movement amount from the home Make home position setting
counter value of the position exceeded a 32767 rotation or - again.
absolute position encoder 37268 rotation in succession.
exceeded the maximum
revolution range.
AL.E6 Servo forced stop EMG-SG are open. External forced stop was made valid. Ensure safety and deactivate
warning (EMG-SG opened.) forced stop.
AL.E9 Main circuit off Servo-on (RYn0) was Switch on main circuit power.
warning turned ON with the main
circuit power OFF.
12 - 13
12. TROUBLESHOOTING
MEMO
12 - 14
13. OUTLINE DIMENSION DRAWINGS
13.1 Servo amplifiers
(1) MR-J2S-10CP-S084 to MR-J2S-60CP-S084 MR-J2S-10CP1-S084 to MR-J2S-40CP1-S084

[Unit: mm]
A Approx.70 (2.76) ([Unit: in])

135 (5.32)
Approx.20
6 ( 0.24) mounting hole B Terminal layout
(0.79)
(Terminal cover open)
(0.24)
6
MITSUBISHI MITSUBISHI
OPEN OPEN
C C C C
N N N N
1 1 1 1
168 (6.61)
156 (6.14)
A B A B
C C
Rating plate C C
N N N N
2 3 2 3
E
N TE1 E
N
C C
L1 L2 L3
(Note)
6 (0.24)
U V W
Approx.7
TE2
(0.28)
6 PE terminal
(0.24)
4(0.16)
Variable dimensions Mass

Servo amplifier
A B [kg] ([lb])
MR-J2S-10CP (1)-S084
50 (1.97) 6 (0.24) 0.7 (1.54)
MR-J2S-20CP (1)-S084
MR-J2S-40CP (1)-S084
70 (2.76) 22 (0.87) 1.1 (2.43)
MR-J2S-60CP-S084
Note. This data applies to the 3-phase 200 to 230VAC and 1-phase 230VAC power supply models.
TE1
For 3-phase 200 to 230VAC and 1-phase 230VAC For 1-phase 100 to 120VAC
L1 L2 L3 L1 L2
U V W U V W
Terminal screw: M4 Terminal screw: M4

Tightening torque: 1.2 [N m] (10.6 [lb in]) Tightening torque: 1.2 [N m] (10.6 [lb in])
PE terminals
TE2
Front
D C P L21 L11
Terminal screw: M4
Tightening torque: 1.2 [N m] (10.6 [lb in])
13 - 1
(2) MR-J2S-70CP-S084 MR-J2S-100CP-S084

[Unit: mm]
6 ( 0.24) 70(2.76) ([Unit: in])
mounting hole Approx.70(2.76) 190(7.48)
22
Approx.20
Terminal layout
(0.24)
(0.79)
(0.87)
(Terminal cover open)
6
OPEN OPEN
C C C C
N N N N
1 1 1 1
A B
168(6.61)
156(6.14)
A B
C C
Rating plate C C
N N N N
2 3 2 3
E E
N N
C C
L1 L2 L3
6(0.24)
U V W
PE terminal
Approx.7
6(0.24) TE2 TE1

(0.28)
22 42 6(0.24)
(0.87) (1.65)
6(0.24)
Mass
Servo amplifier
[kg] ([lb])
MR-J2S-70CP-S084
1.7 (3.75)
MR-J2S-100CP-S084
TE1
L1 L2 L3
U V W
Terminal screw: M4
TE2
Front
D C P L21 L11 N
PE terminals
Terminal screw: M4
13 - 2
(3) MR-J2S-200CP-S084 MR-J2S-350CP-S084

[Unit: mm]
([Unit: in])
2- 6 ( 0.24) 90(3.54) Approx.70(2.76) 195(7.68)
mounting hole 6 78(3.07)
(0.24)
(0.24) Terminal layout

6
168(6.61)
156(6.14)
TE2
TE1
PE terminal
Cooling fan wind direction
Mass
Servo amplifier
[kg] ([lb])
MR-J2S-200CP-S084
2.0 (4.41)
MR-J2S-350CP-S084
TE1 PE terminals
L1 L2 L3 U V W
Terminal screw: M4
Terminal screw: M4
TE2
L11 L21 D P C N
Terminal screw: M4
13 - 3
(4) MR-J2S-500CP-S084
2- 6( 0.24) [Unit: mm]
mounting hole ([Unit: in])
(0.24) 130(5.12) (0.24) Approx.70 200(7.87)
Approx.
6 118(4.65) 6 (2.76) (0.19) 5
(0.79)
(0.5)
7.5
Terminal layout
20
OPEN MITSUBISHI MITSUBISHI
OPEN OPEN
TE1
C C C C
N N N N
1 1 1 1
A B A B
C C C C
250(9.84)
235(9.25)
N N N N
2 3 2 3
TE2
N.P. N.P.
6(0.24)
(0.5)
Cooling fan
7.5
Mass
Servo amplifier
[kg] ([lb])
MR-J2S-500CP-S084 4.9 (10.8)
TE1 PE terminals
Terminal screw : M4 Built-in regenerative resistor

L1
Tightening torque : 1.2 [N m] (10.6 [lb in]) lead terminal fixing screw
L2
L3
C
P
N
U
V
W
Terminal screw : M4
Tightening torque : 1.2 [N m] (10.6 [lb in])
TE2
L11 Terminal screw : M3.5

L21
13 - 4
(5) MR-J2S-700CP-S084
2- 6( 0.24) [Unit: mm]
mounting hole ([Unit: in])
(0.39) 180(7.09) Approx.70 200(7.87)
10 160(6.23) 10 (2.76) 138(5.43) 62
Approx.
(0.5)
(2.44) 6(0.24)
7.5
(0.79)
(0.39)
Terminal layout
20
OPEN OPEN
C C C C
N N N N
1 1 1 1
A B A B
C C C C
N N N N
2 3 2 3
TE2
350(13.8)
335(13.2)
OPEN
Cooling fan
TE1
6 (0.24)
(0.5)
7.5
Mass
Servo amplifier
[kg] ([lb])
MR-J2S-700CP-S084 7.2 (15.9)
TE1 PE terminals
L1 L2 L3 C P N U V W
Terminal screw : M4 Built-in regenerative resistor
Tightening torque : 1.2 [N m] (10.6 [lb in]) lead terminal fixing screw
Terminal screw : M4
TE2
L11 Terminal screw : M3.5

L21
13.2 CC-Link option unit (MR-J2S-T01)

2- 6(0.24)Mounting hole [Unit: mm(in)]
Module screw
25(0.98) tightening torque Approx.70(2.76)
135(5.32)
2.5[N m]
(0.24) 6 6 (0.24)
(22.1[lb in])
(0.24)
6
MR-J2S-T0
C
N
1
0
R
S
W
1
2
156(6.14)
168(6.61)
1 Rating
2
S
W
PLATE
C
N
3
0
ERR SD
LRUN RD
SERR WD
C
N
4
0
(0.24)
POWER
CPU ERR
6
Weight: 0.3kg(0.66lb)
13 - 5
13.3 Connectors
(1) Servo amplifier side

<3M >
(a) Soldered type

Model [Unit: mm]
Connector : 10120-3000PE ([Unit: in])
Shell kit : 10320-52F0-008
12.0(0.47)
10.0(0.39)
14.0
22.0 (0.87) (0.55)
Logo, etc. are indicated here.

39.0 (1.54)
23.8 (0.94)
33.3 (1.31)
12.7(0.50)
(b) Threaded type

Model [Unit: mm]
Connector : 10120-3000PE ([Unit: in])
Shell kit : 10320-52A0-008
Note. This is not available as option 12.0
(0.47)
and should be user-prepared.
(0.39)
10.0
22.0 14.0
(0.87) (0.55) 27.4 (1.08)
39.0 (1.54)
(0.94)
23.8
12.7
(0.21)
33.3
5.2
(1.31) (0.50)
(c) Insulation displacement type

Model [Unit: mm]
Connector : 10120-6000EL ([Unit: in])
Shell kit : 10320-3210-000
6.7
11.5(0.45)
( 0.26)
20.9 (0.82) Logo, etc. are indicated here.

2- 0.5 (0.02)
42.0 (1.65)
33.0 (1.30)
29.7 (1.17)
13 - 6
(2) Communication cable connector

<JAE>
[Unit: mm]
([Unit: in])
B
Fitting fixing screw G E (max. diameter of

F
cable used)
C
D
A B C D F
Type E G
1 1 0.25 1 reference
DE-C1-J6-S6 34.5 (1.36) 19 (0.75) 24.99 (0.98) 33 (1.30) 6 (0.24) 18 (0.71) #4-40
13 - 7
MEMO
13 - 8
14. CHARACTERISTICS
14. CHARACTERISTICS
14.1 Overload protection characteristics
An electronic thermal relay is built in the servo amplifier to protect the servo motor and servo amplifier
from overloads. Overload 1 alarm (AL.50) occurs if overload operation performed is above the electronic
thermal relay protection curve shown in any of Figs 14.1. Overload 2 alarm (AL.51) occurs if the
maximum current flew continuously for several seconds due to machine collision, etc. Use the equipment
on the left-hand side area of the continuous or broken line in the graph.
In a machine like the one for vertical lift application where unbalanced torque will be produced, it is
recommended to use the machine so that the unbalanced torque is 70% or less of the rated torque.
1000 1000
During rotation
During rotation
100 100
Operation time [s]

Operation time[s]
During servo lock

10 10
During servo lock

1 1
0.1 0.1
0 50 100 150 200 250 300 0 50 100 150 200 250 300
(Note) Load ratio [%] (Note) Load ratio [%]
a. MR-J2S-10CP-S084 to MR-J2S-100CP-S084 b. MR-J2S-200CP-S084 to MR-J2S-350CP-S084

10000
1000
During rotation
Operation time[s]
During servo lock

100
10
0 50 100 150 200 250 300
(Note) Load ratio [%]
c. MR-J2S-500CP-S084 MR-J2S-700CP-S084
Note. If operation that generates torque more than 100% of the rating is performed with an abnormally high frequency in a servo motor
stop status (servo lock status) or in a 30r/min or less low-speed operation status, the servo amplifier may fail even when the
electronic thermal relay protection is not activated.
Fig 14.1 Electronic thermal relay protection characteristics
14 - 1
14. CHARACTERISTICS
14.2 Power supply equipment capacity and generated loss
(1) Amount of heat generated by the servo amplifier

Table 12.1 indicates servo amplifiers' power supply capacities and losses generated under rated load.
For thermal design of an enclosure, use the values in Table 14.1 in consideration for the worst
operating conditions. The actual amount of generated heat will be intermediate between values at
rated torque and servo-off according to the duty used during operation. When the servo motor is run at
less than the maximum speed, the power supply capacity will be smaller than the value in the table,
but the servo amplifier's generated heat will not change.
Table 14.1 Power supply capacity and generated heat per servo amplifier at rated output
(Note 1) (Note 2)
Area required for heat dissipation
Servo amplifier Servo motor Power supply Servo amplifier-generated heat[W]
capacity[kVA] At rated torque With servo off [m2] [ft2]
HC-KFS053 13 0.3 25 15 0.5 5.4
MR-J2S-10CP(1)
HC-MFS053 13 0.3 25 15 0.5 5.4
-S084
HC-UFS13 0.3 25 15 0.5 5.4
HC-KFS23 0.5 25 15 0.5 5.4
MR-J2S-20CP(1)
HC-MFS23 0.5 25 15 0.5 5.4
-S084
HC-UFS23 0.5 25 15 0.5 5.4
HC-KFS43 0.9 35 15 0.7 7.5
MR-J2S-40CP(1)
HC-MFS43 0.9 35 15 0.7 7.5
-S084
HC-UFS43 0.9 35 15 0.7 7.5
HC-SFS52 1.0 40 15 0.8 8.6
MR-J2S-60CP
HC-SFS53 1.0 40 15 0.8 8.6
-S084
HC-LFS52 1.0 40 15 0.8 8.6
HC-KFS73 1.3 50 15 1.0 10.8
MR-J2S-70CP
HC-MFS73 1.3 50 15 1.0 10.8
-S084
HC-UFS72 73 1.3 50 15 1.0 10.8
HC-SFS81 1.5 50 15 1.0 10.8
MR-J2S-100CP
HC-SFS102 103 1.7 50 15 1.0 10.8
-S084
HC-LFS102 1.7 50 15 1.0 10.8
HC-SFS121 2.1 90 20 1.8 19.4
HC-SFS201 3.5 90 20 1.8 19.4
HC-SFS152 153 2.5 90 20 1.8 19.4
MR-J2S-200CP HC-SFS202 203 3.5 90 20 1.8 19.4
-S084 HC-RFS103 1.8 50 15 1.0 10.8
HC-RFS153 2.5 90 20 1.8 19.4
HC-UFS152 2.5 90 20 1.8 19.4
HC-LFS152 2.5 90 20 1.8 19.4
HC-SFS301 4.8 120 20 2.7 29.1
HC-SFS352 353 5.5 130 20 2.7 29.1
MR-J2S-350CP
HC-RFS203 3.5 90 20 1.8 19.4
-S084
HC-UFS202 3.5 90 20 1.8 19.4
HC-LFS202 3.5 90 20 1.8 19.4
HC-SFS502 7.5 195 25 3.9 42.0
HC-RFS353 5.5 135 25 2.7 29.1
HC-RFS503 7.5 195 25 3.9 42.0
MR-J2S-500CP
HC-UFS352 5.5 195 25 3.9 42.0
-S084
HC-UFS502 7.5 195 25 3.9 42.0
HC-LFS302 4.5 120 25 2.4 25.8
HA-LFS502 7.5 195 25 3.9 42.0
MR-J2S-700CP HC-SFS702 10.0 300 25 6.0 64.6
-S084 HA-LFS702 10.6 300 25 6.0 64.6
Note 1. Note that the power supply capacity will vary according to the power supply impedance. This value assumes that the power
factor improving reactor is not used.
2. Heat generated during regeneration is not included in the servo amplifier-generated heat. To calculate heat generated by the
regenerative option, refer to section 15.1.1.
14 - 2
14. CHARACTERISTICS
(2) Heat dissipation area for enclosed servo amplifier

The enclosed control box (hereafter called the control box) which will contain the servo amplifier
should be designed to ensure that its temperature rise is within 10 ( 50 ) at the ambient
temperature of 40 (104 ). (With a 5 (41 ) safety margin, the system should operate within a
maximum 55 (131 ) limit.) The necessary enclosure heat dissipation area can be calculated by
Equation 14.1.
P
A ............................................................................................................................................. (14.1)
K T
where, A : Heat dissipation area [m2]

P : Loss generated in the control box [W]
T : Difference between internal and ambient temperatures [ ]
K : Heat dissipation coefficient [5 to 6]
When calculating the heat dissipation area with Equation 14.1, assume that P is the sum of all losses
generated in the enclosure. Refer to Table 14.1 for heat generated by the servo amplifier. "A" indicates
the effective area for heat dissipation, but if the enclosure is directly installed on an insulated wall,
that extra amount must be added to the enclosure's surface area.
The required heat dissipation area will vary wit the conditions in the enclosure. If convection in the
enclosure is poor and heat builds up, effective heat dissipation will not be possible. Therefore,
arrangement of the equipment in the enclosure and the use of a cooling fan should be considered.
Table 14.1 lists the enclosure dissipation area for each servo amplifier when the servo amplifier is
operated at the ambient temperature of 40 (104 ) under rated load.
(Outside) (Inside)
Air flow
Fig. 14.2 Temperature distribution in enclosure
When air flows along the outer wall of the enclosure, effective heat exchange will be possible, because
the temperature slope inside and outside the enclosure will be steeper.
14 - 3
14. CHARACTERISTICS
14.3 Dynamic brake characteristics
14.3.1 Dynamic brake operation
(1) Calculation of coasting distance

Fig. 14.3 shows the pattern in which the servo motor comes to a stop when the dynamic brake is
operated. Use Equation 14.2 to calculate an approximate coasting distance to a stop. The dynamic
brake time constant varies with the servo motor and machine operation speeds. (Refer to (2) in this
section.)
ON
Forced stop (EMG)
OFF
Time constant
V0
Machine speed
te Time
Fig. 14.3 Dynamic brake operation diagram
V0 JL
Lmax te 1 ....................................................................................................................... (14.2)
60 JM
Lmax : Maximum coasting distance .................................................................................................[mm][in]

V0 : Machine rapid feed rate ........................................................................................ [mm/min][in/min]
JM : Servo motor inertial moment................................................................................. [kg cm2][oz in2]
JL : Load inertia moment converted into equivalent value on servo motor shaft..... [kg cm2][oz in2]
: Brake time constant ........................................................................................................................ [s]
te : Delay time of control section........................................................................................................... [s]
(There is internal relay delay time of about 30ms.)
(2) Dynamic brake time constant

The following shows necessary dynamic brake time constant for the equations (14.2).
0.02
16 0.018
0.016
Time constant [s]
14 23
[ms]
0.014
12
0.012 23
10 73
Time constant
0.01 73
8 053
0.008
6
0.006
4 0.004 053
2 43 13 0.002 43
0 0 13
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
Speed [r/min] Speed [r/min]
a. HC-KFS series b. HC-MFS series
14 - 4
14. CHARACTERISTICS
0.04 0.045
0.035 121 0.04
Time constant [s]
0.03 0.035 702
Time constant [s]

201
0.025 0.03
352
0.025 202
0.02 301 52
0.02
0.015
0.015 502
0.01 152
0.01
0.005 81 102
0.005
0 0
0 50 500 1000 0 500 1000 1500 2000
c. HC-SFS1000r/min series d. HC-SFS2000r/min series

0.12
0.018
0.1 203 0.016
Time constant [s]

Time constant [s]
53 0.014
0.08
0.012
0.06 0.01 103 503
0.008
0.04 353 153
0.006
0.02 103 0.004
0.002 353
153 203
0 0
0 50 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
e. HC-SFS3000r/min series f. HC-RFS series

0.07
73
0.06
0.05
0.1
Time constant [s]
0.09 0.04
72
0.08 502
Time constant [s]
0.07 352 0.03

0.06
43
0.05
0.02 23
0.04
13
0.03
0.02 0.01
152 202
0.01
0 0
0 500 1000 1500 2000 0 50 500 10001500200025003000
g. HC-UFS 2000r/min series h. HC-UFS3000r/min series
14 - 5
14. CHARACTERISTICS
40.0
35.0
30.0
Time constant [s]
25.0
302
20.0
15.0
10.0
5.0
0
0 500 1000 1500 2000
Speed [r/min]
i. HC-LFS 2000r/min series
14.3.2 The dynamic brake at the load inertia moment
Use the dynamic brake under the load inertia moment ratio indicated in the following table. If the load
inertia moment is higher than this value, the built-in dynamic brake may burn. If there is a possibility
that the load inertia moment may exceed the value, contact Mitsubishi.
Servo amplifier Load inertia moment ratio [times]

MR-J2S-10CP-S084
to MR-J2S-200CP-S084
30
MR-J2S-10CP1-S084
to MR-J2S-40CP1-S084
MR-J2S-350CP-S084 16
MR-J2S-500CP-S084
15
MR-J2S-700CP-S084
14 - 6
14. CHARACTERISTICS
14.4 Encoder cable flexing life
The flexing life of the cables is shown below. This graph calculated values. Since they are not guaranteed
values, provide a little allowance for these values.
1 108 a
5 107
1 107
5 106 a : Long flexing-life encoder cable
MR-JCCBL M-H
MR-JHSCBL M-H
MR-ENCBL M-H
Flexing life [times]
1 106
5 105 b : Standard encoder cable
MR-JCCBL M-L
MR-JHSCBL M-L
1 105
5 104
1 104
b
5 103
1 103
4 7 10 20 40 70 100 200
Flexing radius [mm]
14.5 Inrush currents at power-on of main circuit and control circuit
The following table indicates the inrush currents (reference data) that will flow when the maximum
permissible voltage (253VAC) is applied at the power supply capacity of 2500kVA and the wiring length of
1m (3.28ft).
Inrush Currents (A0-p)

Servo Amplifier
Main circuit power supply (L1, L2, L3) Control circuit power supply (L11, L21)
MR-J2S-10CP-S084
30A (Attenuated to approx. 5A in 10ms)
20CP-S084
MR-J2S-40CP-S084 70 to 100A
60CP-S084 (Attenuated to approx. 0A in 0.5 to 1ms)
MR-J2S-70CP-S084
100CP-S084
MR-J2S-200CP-S084 100 to 130A
350CP-S084 (Attenuated to approx. 0A in 0.5 to 1ms)
MR-J2S-500CP-S084 44A (Attenuated to approx. 20A in 20ms) 30A
MR-J2S-700CP-S084 88A (Attenuated to approx. 20A in 20ms) (Attenuated to approx. 0A in several ms)
MR-J2S-10CP1-S084
59A (Attenuated to approx. 5A in 4ms) 100 to 130A
20CP1-S084
(Attenuated to approx. 0A in 0.5 to 1ms)
MR-J2S-40CP1-S084 72A (Attenuated to approx. 5A in 4ms)
Since large inrush currents flow in the power supplies, always use no-fuse breakers and magnetic
contactors. (Refer to section 15.2.2.)
When circuit protectors are used, it is recommended to use the inertia delay type that will not be tripped
by an inrush current.
14 - 7
14. CHARACTERISTICS
MEMO
14 - 8
15. OPTIONS AND AUXILIARY EQUIPMENT
Before connecting any option or peripheral equipment, turn off the power and wait
for 15 minutes or more until the charge lamp turns off. Then, confirm that the
WARNING voltage between P and N is safe with a voltage tester and others. Otherwise, an
electric shock may occur. In addition, always confirm from the front of the servo
amplifier whether the charge lamp is off or not.
Use the specified auxiliary equipment and options. Unspecified ones may lead to a
CAUTION fault or fire.
15.1 Options
15.1.1 Regenerative options
The specified combinations of regenerative options and servo amplifiers may only
CAUTION be used. Otherwise, a fire may occur.
(1) Combination and regenerative power

The power values in the table are resistor-generated powers and not rated powers.
Regenerative power[W]
Servo amplifier (Note) (Note)
Built-in regenerative MR-RB032 MR-RB12 MR-RB32 MR-RB30 MR-RB31
MR-RB50 MR-RB51
resistor [40 ] [40 ] [40 ] [13 ] [6.7 ]
[13 ] [6.7 ]
MR-J2S-10CP(1)
30
-S084
MR-J2S-20CP (1)
10 30 100
-S084
MR-J2S-40CP (1)
10 30 100
-S084
MR-J2S-60CP-
10 30 100
S084
MR-J2S-70CP-
20 30 100 300
S084
MR-J2S-100CP-
20 30 100 300
S084
MR-J2S-200CP-
100 300 500
S084
MR-J2S-350CP-
100 300 500
S084
MR-J2S-500CP-
130 300 500
S084
MR-J2S-700CP-
170 300 500
S084
Note. Always install a cooling fan.
15 - 1
(2) Selection of the regenerative option

(a) Simple selection method
In horizontal motion applications, select the regenerative option as described below.
When the servo motor is run without load in the regenerative mode from the running speed to a
stop, the permissible duty is as indicated in section 5.1 of the separately available Servo Motor
Instruction Manual.
For the servo motor with a load, the permissible duty changes according to the inertia moment of
the load and can be calculated by the following formula.
Permissible Permissible duty for servo motor with no load (value indication Section 5.1 in Servo Motor Instruction Manual)
duty (m 1)
2
ratedspeed [times/min]
running speed
where m load inertia moment/servo motor inertia moment
From the permissible duty, find whether the regenerative option is required or not.
Permissible duty number of positioning times [times/min]
Select the regenerative option out of the combinations in (1) in this section.
(b) To make selection according to regenerative energy

Use the following method when regeneration occurs continuously in vertical motion applications or
when it is desired to make an in-depth selection of the regenerative option.
a. Regenerative energy calculation
Use the following table to calculate the regenerative energy.
Servo motor speed
tf(1 cycle)
N0
Up
Time
Unbalance torque
M Down
t1 t2 t3 t4
Firiction Tpsa1 Tpsd1 Tpsa2 Tpsd2
torque 1)
( )
(Driving)
Generated torque
TF
2) 4) 8)
5)
TU
6)
3)
(Regenerative) 7)
( )
Formulas for calculating torque and energy in operation
Regenerative power Torque applied to servo motor [N m] Energy [J]
(JL JM) N0 1 0.1047
1) T1 TU TF E1 N0 T1 Tpsa1
9.55 104 Tpsa1 2
2) T2 TU TF E2 0.1047 N0 T2 t1
(JL JM) N0 1 0.1047
3) T3 TU TF E3 N0 T3 Tpsd1
9.55 104 Tpsd1 2
4), 8) T4 TU E4 0 (N0 regeneration)
(JL JM) N0 1 0.1047
5) T5 4 TU TF E5 N0 T5 Tpsa2
9.55 10 Tpsa2 2
6) T6 TU TF E6 0.1047 N0 T6 t3
(JL JM) N0 1 0.1047
7) T7 TU TF E7 N0 T7 Tpsd2
9.55 104 Tpsd2 2
From the calculation results in 1) to 8), find the absolute value (Es) of the sum total of negative
energies.
15 - 2
b. Losses of servo motor and servo amplifier in regenerative mode

The following table lists the efficiencies and other data of the servo motor and servo amplifier in
the regenerative mode.
Servo amplifier Inverse efficiency[%] Capacitor charging[J]

MR-J2S-10CP-S084 55 9
MR-J2S-10CP1-S084 55 4
MR-J2S-20CP-S084 70 9
MR-J2S-20CP1-S084 70 4
MR-J2S-40CP-S084 85 11
MR-J2S-40CP1-S084 85 10
MR-J2S-60CP-S084 85 11
MR-J2S-70CP-S084 80 18
MR-J2S-100CP-S084 80 18
MR-J2S-200CP-S084 85 40
MR-J2S-350CP-S084 85 40
MR-J2S-500CP-S084 90 45
MR-J2S-700CP-S084 90 70
Inverse efficiency ( ) : Efficiency including some efficiencies of the servo motor and servo
amplifier when rated (regenerative) torque is generated at rated
speed. Since the efficiency varies with the speed and generated torque,
allow for about 10%.
Capacitor charging (Ec) : Energy charged into the electrolytic capacitor in the servo amplifier.
Subtract the capacitor charging from the result of multiplying the sum total of regenerative
energies by the inverse efficiency to calculate the energy consumed by the regenerative option.
ER [J] Es Ec
Calculate the power consumption of the regenerative option on the basis of single-cycle operation
period tf [s] to select the necessary regenerative option.
PR [W] ER/tf
(3) Connection of the regenerative option

Set parameter No.0 according to the option to be used.
Parameter No.0
Selection of regenerative
0: Not used (The built-in regenerative resistor is used.
However, the MR-J2S-10CP-S084 does not have a built-in
regenerative resistor and therefore cannot use it.)
1: FR-RC, FR-BU2
2: MR-RB032
3: MR-RB12
4: MR-RB32
5: MR-RB30
6: MR-RB50 (Cooling fan is required)
8: MR-RB31
9: MR-RB51 (Cooling fan is required)
15 - 3
(4) Connection of the regenerative option
POINT
When the MR-RB50 MR-RB51 is used, a cooling fan is required to cool it.
The cooling fan should be prepared by the customer.
The regenerative option will generate heat of about 100 . Fully examine heat dissipation, installation
position, used cables, etc. before installing the option. For wiring, use flame-resistant cables and keep
them clear of the regenerative option body. Always use twisted cables of max. 5m length for connection
with the servo amplifier.
(a) MR-J2S-350CP-S084 or less

Always remove the wiring from across P-D and fit the regenerative option across P-C.
The G3 and G4 terminals act as a thermal sensor. G3-G4 is opened when the regenerative option
overheats abnormally.
Always remove the lead from across P-D.
Servo amplifier
Regenerative option
D
P
P
C
C
G3
(Note 2) G4
5m (16.4 ft) max.
Cooling fan(Note 1)
Note 1. When using the MR-RB50, forcibly cool it with a cooling fan (92 92, minimum air flow : 1.0m3).
2. Make up a sequence which will switch off the magnetic contactor (MC) when
abnormal heating occurs.
G3-G4 contact specifications
Maximum voltage: 120V AC/DC
Maximum current: 0.5A/4.8VDC
Maximum capacity: 2.4VA
For the MR-RB50 install the cooling fan as shown.

[Unit : mm(in)]
Cooling fan installation screw hole dimensions
Top 2-M3 screw hole
(for cooling fan installation)
Cooling fan Terminal block Depth 10 or less
(Screw hole already
machined)
(3.25)
82.5
Thermal relay
(5.24)
133
Bottom 82.5 40 (1.58)

(3.25)
Vertical Horizontal installation Installation surface

installation
15 - 4
(b) MR-J2S-500CP-S084 MR-J2S-700CP-S084

Always remove the wiring (across P-C) of the servo amplifier built-in regenerative resistor and fit
the regenerative option across P-C.
The G3 and G4 terminals act as a thermal sensor. G3-G4 is opened when the regenerative option
overheats abnormally.
Always remove wiring (across P-C) of servo
amplifier built-in regenerative resistor.
Servo amplifier
Regenerative option
P
P
C
C
G3
(Note 2) G4
5m(16.4ft) or less
Cooling fan(Note 1)
Note 1. When using the MR-RB50 MR-RB51, forcibly cool it with a cooling fan (92 92, minimum air flow : 1.0m3).
2. Make up a sequence which will switch off the magnetic contactor (MC)
when abnormal heating occurs.
G3-G4 contact specifications
Maximum voltage: 120V AC/DC
Maximum current: 0.5A/4.8VDC
Maximum capacity: 2.4VA
When using the regenerative resistor option, remove the servo amplifier's built-in regenerative
resistor terminals (across P-C), fit them back to back, and secure them to the frame with the
accessory screw as shown below.
Mounting method
Accessory screw
For MR-J2S-500CP-S084 For MR-J2S-700CP-S084
Accessory screw
Accessory screw
15 - 5
For the MR-RB50 MR-RB51 install the cooling fan as shown.

[Unit : mm(in)]
Cooling fan installation screw hole dimensions
Top 2-M3 screw hole
(for cooling fan installation)
Cooling fan Terminal block Depth 10 or less
(Screw hole already
machined)
(3.25)
82.5
Thermal relay
(5.24)
133
Bottom 82.5 40 (1.58)
(3.25)
Vertical Horizontal installation Installation surface

installation
(5) Outline drawing

(a) MR-RB032 MR-RB12
[Unit: mm (in)]
LA
6 (0.24) mounting hole
6 (0.24)
LB
12 (0.47)
MR-RB
168 (6.61)
144 (5.67)
156 (6.14)
TE1
5 (0.20) Terminal block
G3
G3
G4
G4
TE1
C
P
P
C
Terminal screw: M3
12 (0.47)
Tightening torque:
0.5 to 0.6 [N m] (4 to 5 [lb in])
6 (0.24)
Mounting screw
6 (0.24) 1.6 (0.06)
Screw size: M5
20
(0.79) Tightening torque:
LD
3.24 [N m] (28.7 [lb in])
LC
Regenerative Variable dimensions Mass

option LA LB LC LD [kg] [lb]
MR-RB032 30 (1.18) 15 (0.59) 119 (4.69) 99 (3.9) 0.5 1.1
MR-RB12 40 (1.58) 15 (0.59) 169 (6.69) 149 (5.87) 1.1 2.4
15 - 6
(b) MR-RB30 MR-RB31 MR-RB32

[Unit: mm (in)]
Terminal block
P
C Terminal screw: M4
G3 Tightening torque: 1.2 [N m] (10.6 [Ib in])
G4
Mounting screw
Screw: M6
7 (0.28) 318 (12.52) Tightening torque: 5.4 [N m] (47.79 [Ib in])
17 335 (13.19)
10 90 (3.54) (0.67)
Regenerative
(0.39) 100 (3.94) Mass [kg] (Ib)
option
MR-RB30
MR-RB31 2.9 (6.4)
MR-RB32
(c) MR-RB50 MR-RB51

[Unit: mm (in)]
Cooling fan mounting screw Terminal block
(2-M3 screw)
On opposite side P
49 82.5 C Terminal screw: M4
(1.93) (3.25) G3 Tightening torque: 1.2 [N m]
G4 (10.6 [Ib in])
Mounting screw
7 14 Screw: M6
slot Tightening torque: 5.4 [N m]
(47.79 [Ib in])
Wind blows in the Regenerative

arrow direction Mass [kg] (Ib)
option
MR-RB50
5.6 (12.3)
MR-RB51
2.3 7 (0.28)
(0.09) 200 (7.87) 17 12 108 (4.25) Approx.30 (1.18)
217 (8.54) (0.67) (0.47) 120 (4.73) 8 (0.32)
15 - 7
15.1.2 FR-BU2 brake unit
POINT
Use a 200V class brake unit and a resistor unit with a 200V class servo
amplifier. Combination of different voltage class units and servo amplifier
cannot be used.
Install a brake unit and a resistor unit on a flat surface vertically. When
the unit is installed horizontally or diagonally, the heat dissipation effect
diminishes.
Temperature of the resistor unit case rises to higher than 100 . Keep
cables and flammable materials away from the case.
Ambient temperature condition of the brake unit is between 10 (14 )
and 50 (122 ). Note that the condition is different from the ambient
temperature condition of the servo amplifier (0 (32 ) and 55
(131 )).
Configure the circuit to shut down the power-supply with the alarm
output of the brake unit and resistor unit under abnormal condition.
Use the brake unit with a combination indicated in this section (1).
For executing a continuous regenerative operation, use FR-RC power
regeneration converter.
Brake unit and regenerative options (Regenerative resistor) cannot be
used simultaneously.
Connect the brake unit to the bus of the servo amplifier. As compared to the MR-RB regenerative option,
the brake unit can return larger power. Use the brake unit when the regenerative option cannot provide
sufficient regenerative capability.
When using the brake unit, set the parameter No.0 of the servo amplifier to " 01 ".
When using the brake unit, always refer to the FR-BU2-(H) Brake Unit Instruction Manual.
(1) Selection
Use a combination of servo amplifier, brake unit and resistor unit listed below.
Number of Permissible Total

Applicable servo
Brake unit Resistor unit connected continuous resistance
amplifier
units power [kW] [ ]
MR-J2S-350CP-S084
FR-BU2-15K FR-BR-15K 1 0.99 8
MR-J2S-500CP-S084
MR-J2S-500CP-S084
FR-BU2-30K FR-BR-30K 1 1.99 4
MR-J2S-700CP-S084
15 - 8
(2) Brake unit parameter setting

Normally, when using the FR-BU2, changing parameters is not necessary. Whether a parameter can
be changed or not is listed below.
Parameter Change
possible/ Remarks
No. Name
impossible
0 Brake mode switchover Impossible Do not change the parameter.
1 Monitor display data selection Possible Refer to the FR-BU2-(H) Brake Unit
Instruction Manual.
2 Input terminal function selection 1 Impossible Do not change the parameter.
3 Input terminal function selection 2
77 Parameter write selection
78 Cumulative energization time
carrying-over times
CLr Parameter clear
ECL Alarm history clear
C1 For manufacturer setting
15 - 9
POINT
Connecting PR terminal of the brake unit to P terminal of the servo
amplifier results in brake unit malfunction. Always connect the PR
terminal of the brake unit to the PR terminal of the resistor unit.
ALM EMG OFF ON

RA1
MC
MC
SK
Servo amplifier
NFB MC CN1B
(Note 1) L1 15 EMG
Power L2 10 SG
supply FR-BR
L3 3 VDD
(Note 4) TH1
L11 13 COM P
TH2
L21 18 ALM RA1 PR
FR-BU2
D (Note 6) PR MSG
P P/ SD
(Note 3) A
(Note 7) N/
B
N
C
C BUE
(Note 8)(Note 5)
SD
(Note 2)
Note 1. For power supply specifications, refer to section 1.2.

2. For the servo amplifier of 5k and 7kW, always disconnect the lead of built-in regenerative resistor, which is connected to the P
and C terminals.
3. Connect the P/ and N/ terminals of the brake unit to a correct destination. Wrong connection results in servo amplifier and
brake unit malfunction.
4. Contact rating: 1b contact, 110VAC_5A/220VAC_3A
Normal condition: TH1-TH2 is conducting. Abnormal condition: TH1-TH2 is not conducting.
5. Contact rating: 230VAC_0.3A/30VDC_0.3A
Normal condition: B-C is conducting/A-C is not conducting. Abnormal condition: B-C is not conducting/A-C is conducting.
6. For the servo amplifier of 3.5kW, always disconnect the wiring between P and D terminals.
7. Do not connect more than one cable to each P to N terminals of the servo amplifier.
8. Always connect between BUE and SD terminals (Factory-wired).
15 - 10
(a) Precautions for wiring

The cables between the servo amplifier and the brake unit, and between the resistor unit and the
brake unit should be as short as possible. Always twist the cable longer than 5m (twist five times
or more per one meter). Even when the cable is twisted, the cable should be less than 10m. Using
cables longer than 5m without twisting or twisted cables longer than 10m, may result in the brake
unit malfunction.
Brake unit Resistor unit Brake unit Resistor unit
P P P P P Twist P P Twist P
N N PR PR N N PR PR
5m or less 5m or less 10m or less 10m or less
(b) Cables
1) Cables for the brake unit
For the brake unit, HIV cable (600V grade heat-resistant PVC insulated wire) is recommended.
a) Main circuit terminal

Main Crimping Cable size
Tightening
circuit terminal N/ , P/ , PR,
torque
Brake unit terminal
N/ , P/ , [N m] HIV cables,
screw AWG
PR, ([Ib in]) etc. [mm2]
N/ P/ PR size
FR-BU2-15K M4 5.5-4 1.5(13.3) 3.5 12
FR-BU2-30K M5 5.5-5 2.5(22.1) 5.5 10
Terminal block
15 - 11
b) Control circuit terminal
POINT
Undertightening can cause a cable disconnection or malfunction.
Overtightening can cause a short circuit or malfunction due to damage to
the screw or the brake unit.
Sheath
PC BUE SD RES SD MSG MSG SD SD Core
A B C
Jumper
6mm
Terminal block
Wire the stripped cable after twisting to prevent the cable
from becoming loose. In addition, do not solder it.
Screw size: M3
Tightening torque: 0.5N m to 0.6N m
Cable size: 0.3mm2 to 0.75 mm2
Screw driver: Small flat-blade screwdriver
(Tip thickness: 0.4mm/Tip width 2.5mm)
(c) Crimping terminals for P and N terminals of servo amplifier
POINT
Always use recommended crimping terminals or equivalent since some
crimping terminals cannot be installed depending on the size.
Number of
Servo amplifier Brake unit connected Crimping terminal Applicable tool Manufacturer
units
MR-J2S-350CP-S084 FR-BU2-15K 1
FR-BU2-15K 1 Japan Solderless
MR-J2S-500CP-S084 FVD5.5-S4 YNT-1210S
FR-BU2-30K 1 Terminal
MR-J2S-700CP-S084 FR-BU2-30K 1
15 - 12
(4) Outline dimension drawings

(a) FR-BU2 brake unit
[Unit: mm]
FR-BU2-15K
5 hole
(Screw size: M4)
Rating
plate
5 4
6 56 6 18.5 52 62
68 132.5
FR-BU2-30K
2- 5 hole
(Screw size: M4)
Rating
plate
5 5
6 96 6 18.5 52 59
108 129.5
15 - 13
(b) FR-BR resistor unit

[Unit: mm]
2 C
(Note)
Control circuit (Note)

terminal
Main circuit
terminal
C C
Approx. 35 W1 1 Approx. 35
W 5
Note. Ventilation ports are provided on both sides and the top. The bottom is open.
Approximate
Resistor unit W W1 H H1 H2 H3 D D1 C mass
[kg]([Ib])
FR-BR-15K 170 100 450 410 20 432 220 3.2 6 15(33.1)
FR-BR-30K 340 270 600 560 20 582 220 4 10 30(66.1)
15.1.3 Power regeneration converter
When using the power regeneration converter, set "01 " in parameter No. 0.
(1) Selection
The converters can continuously return 75% of the nominal regenerative power. They are applied to
the servo amplifiers of the MR-J2S-500CP-S084 and MR-J2S-700CP-S084.
Power Nominal
Continuous energization time [sec]
regeneration regenerative Servo amplifier 500
converter power (kW) 300
FR-RC15 15 MR-J2S-500CP-S084 200
FR-RC30 30 MR-J2S-700CP-S084 100
50
30
20
0 50 75 100 150
Nominal regenerative power (%)
15 - 14

Servo amplifier
L11
L21
Power factor improving reactor
NFB MC FR-BAL
L1
(Note 3)
Power L2
supply
L3
VDD
SG COM
EMG
SON ALM RA2
(Note 2)
N P C
5m(16.4ft) or less
N/ P/
RDY
Ready A
SE
RDY B
B
output
C
C
R/L1 Alarm
S/L2 output
T/L3
RX
R
(Note 1)
SX
Phase detection
S terminals
TX
T
Power regeneration
converter FR-RC
FR-RC Operation ready
RA2 EMG OFF ON
B C
MC MC
SK
Note 1. When not using the phase detection terminals, fit short bars across RX-R, SX-S and TX-T. With the short bars
removed, the FR-RC will not operate.
2. When using servo amplifiers of 5kW and 7kW, always remove the lead of built-in regenerative resistor connected to P
terminal and C terminal.
15 - 15
(3) Outside dimensions of the power regeneration converters

[Unit: mm (in)]
Mounting foot (removable)
2- D hole
Mounting foot
E
movable
Rating plate
Display
Front cover panel
window
BA
B
Cooling fan
D F K
EE
AA
C
A
Heat generation area outside mounting dimension
Power
Approx.
regeneration A AA B BA C D E EE K F
Mass [kg(Ib)]
converter
270 200 450 432 195 10 10 8 3.2 87 19
FR-RC-15K
(10.630) (7.874) (17.717) (17.008) (7.677) (0.394) (0.394) (0.315) (0.126) (3.425) (41.888)
340 270 600 582 195 10 10 8 3.2 90 31
FR-RC-30K
(13.386) (10.630) (23.622) (22.913) (7.677) (0.394) (0.394) (0.315) (0.126) (3.543) (68.343)
(4) Mounting hole machining dimensions

When the power regeneration converter is fitted to a totally enclosed type box, mount the heat
generating area of the converter outside the box to provide heat generation measures. At this time, the
mounting hole having the following dimensions is machined in the box.
[Unit: mm (in)]
Approx.AA (2- D hole)
Model A B D AA BA
260 412 10 200 432
FR-RC-15K
(10.236) (16.220) (0.394) (7.874) (17.009)
330 562 10 270 582
FR-RC-30K
(Mounting hole) (12.992) (22.126) (0.394) (10.630) (22.913)
Approx.BA
15 - 16
15.1.4 Cables and connectors
(1) Cable make-up

The following cables are used for connection with the servo motor and other models. Those indicated
by broken lines in the figure are not options.
Servo amplifier MR-J2S-T01
CN10
9)
Operation
CN1A CN1B
panel
CN2 CN3 CN30

12) Personal
Controller
computer
CN40 13)
10)
11)
10)
11) To U, V, W,
18) 19) HC-KFS
HC-MFS
HC-UFS 3000r/min
1) 2)
6)
HC-SFS
14) 15) 16) 17) HC-RFS
HC-UFS 2000r/min
3) 4) 5)
7) 8)
15 - 17
No. Product Model Description Application

1) Standard encoder MR-JCCBL M-L Connector: 10120-3000PE Housing: 1-172161-9 Standard
cable Refer to (2) in this Shell kit: 10320-52F0-008 Connector pin: 170359-1 flexing life
section. (3M or equivalent) (Tyco Electronics or equivalent) IP20
Cable clamp: MTI-0002
(Toa Electric Industry)
2) Long flexing life MR-JCCBL M-H Long flexing
encoder cable Refer to (2) in this life
section. IP20
3) Standard encoder MR-JHSCBL M-L Connector: 10120-3000PE Connector: D/MS3106B20-29S Standard
cable Refer to (2) in this Shell kit: 10320-52F0-008 Cable clamp: D/MS3057-12A flexing life
section. (3M or equivalent) (DDK) IP20
4) Long flexing life MR-JHSCBL M-H Long flexing
encoder cable Refer to (2) in this life
section.
5) IP65-compliant MR-ENCBL M-H Connector: 10120-3000PE Connector: D/MS3106A20-29S Long flexing
encoder cable Refer to (2) in this Shell kit: 10320-52F0-008 (D190) life
section. (3M or equivalent) Cable clamp: CE3057-12A-3 -D IP65
Back shell: CE02-20BS-S-D IP67
(DDK) Not oil-
resistant.
6) Encoder MR-J2CNM Connector: 10120-3000PE Housing: 1-172161-9 IP20

connector set Shell kit: 10320-52F0-008 Pin: 170359-1
(3M or equivalent) (Tyco Electronics or equivalent)
Cable clamp: MTI-0002
(Toa Electric Industry)
7) Encoder MR-J2CNS Connector: 10120-3000PE Connector: D/MS3106B20-29S IP20

connector set Shell kit: 10320-52F0-008 Cable clamp: D/MS3057-12A
(3M or equivalent) (DDK)
8) Encoder MR-ENCNS Connector: 10120-3000PE Connector: D/MS3106A20-29S IP65

connector set Shell kit: 10320-52F0-008 (D190) IP67
(3M or equivalent) Cable clamp: CE3057-12A-3-D
Back shell: CE02-20BS-S-D
(DDK)
15 - 18
No. Product Model Description Application

9) Control signal MR-J2CN1 Connector: 10120-3000PE
connector set Shell kit: 10320-52F0-008
(3M or equivalent) Qty: 2 each
10) Junction MR-J2TBL M Connector: HIF3BA-20D-2.54R Connector: 10120-6000EL For
terminal block Refer to (Hirose Electric) Shell kit: 10320-3210-000 MR-J2S-T01
cable section15.1.5. (3M or equivalent) connection
11) Junction MR-TB20 Refer to section 15.1.5.

terminal block
12) Bus cable MR-J2HBUS05M Connector: 10120-6000EL Connector: 10120-6000EL For
Shell kit: 10320-3210-000 Shell kit: 10320-3210-000 maintenance
(3M or equivalent) (3M or equivalent) junction
card
connection
13) Communication Refer to (3) in this Connector: 5557-04R-210 Connector: DE-9SF-N For
cable section. Terminal: 5556 Case: DE-C1-J6-S6 connection
(Molex) (JAE) with PC-AT-
compatible
personal
computer
14) Power supply MR-PWCNS1 Connector: CE05-6A22-23SD-D-BSS
connector set Refer to the Servo Cable clamp:CE3057-12A-2-D
Motor Instruction (DDK)
Manual. Must be
15) Power supply MR-PWCNS2 Connector: CE05-6A24-10SD-D-BSS used to
connector set Refer to the Servo Cable clamp: CE3057-16A-2-D comply with
Motor Instruction (DDK) the EN
Manual. Standard.
16) Power supply MR-PWCNS3 Plug: CE05-6A32-17SD-D-BSS IP65 IP67
connector set Refer to the Servo Cable clamp: CE3057-20A-1-D
Motor Instruction (DDK)
Manual.
17) Brake connector MR-BKCN Plug: D/MS3106A10SL-4S (D190) (DDK) EN
set Refer to the Servo Cable connector: YS010-5-8 (Daiwa Dengyo) Standard-
Motor Instruction compliant
Manual. IP65 IP67
18) Power supply MR-PWCNK1 Plug: 5559-04P-210 IP20
connector set Refer to the Servo Terminal: 5558PBT3L (For AWG16)(6 pcs.)
Motor Instruction (Molex)
Manual.
19) Power supply MR-PWCNK2 Plug: 5559-06P-210 For motor
connector set Terminal: 5558PBT3L (For AWG16)(8 pcs.) with brake
(Molex) IP20
15 - 19
(2) Encoder cable
If you have fabricated the encoder cable, connect it correctly.

CAUTION Otherwise, misoperation or explosion may occur.
POINT
The encoder cable is not oil resistant.
Refer to section 14.4 for the flexing life of the encoder cable.
When the encoder cable is used, the sum of the resistance values of the
cable used for P5 and the cable used for LG should be within 2.4 .
When soldering the wire to the connector pin, insulate and protect the
connection portion using heat-shrinkable tubing.
Generally use the encoder cable available as our options. If the required length is not found in the
options, fabricate the cable on the customer side.
(a) MR-JCCBL M-L MR-JCCBL M-H

These encoder cables are used with the HC-KFS HC-MFS HC-UFS3000r/min series servo
motors.
1) Model explanation
Model: MR-JCCBL M-
Symbol Specifications
L Standard flexing life
H Long flexing life
Symbol (Note) Cable length [m(ft)]

2 2 (6.56)
5 5 (16.4)
10 10 (32.8)
20 20 (65.6)
30 30 (98.4)
40 40 (131.2) Note. MR-JCCBL M-H has
50 50 (164.0) no 40(131.2) and 50m(164.0ft) sizes.
2) Connection diagram
For the pin assignment on the servo amplifier side, refer to section 4.3.1.
Encoder cable
Servo amplifier
supplied to servo motor
Encoder connector Encoder connector
Servo motor 172161-9 (Tyco Electronics)
Encoder cable
(option or fabricated)
1 2 3
MR MRR BAT
CN2 Encoder
4 5 6
50m(164.0ft) max. 30cm MD MDR

(0.98ft) 7 8 9
P5 LG SHD
15 - 20
MR-JCCBL2M-L MR-JCCBL10M-L MR-JCCBL10M-H

MR-JCCBL5M-L to to
MR-JCCBL2M-H MR-JCCBL30M-L MR-JCCBL50M-H
MR-JCCBL5M-H
Servo amplifier side Encoder side Servo amplifier side Encoder side Servo amplifier side Encoder side
P5 19 7 P5 19 7 P5 19 7
LG 11 LG 11 LG 11
P5 20 P5 20 P5 20
LG 12 LG 12 LG 12
P5 18 P5 18 P5 18
LG 2 LG 2 LG 2
8 8 8
MR 7 1 MR 7 1 MR 7 1
MRR 17 2 MRR 17 2 MRR 17 2
MD 6 4 MD 6 4 MD 6 4
MDR 16 5 MDR 16 5 MDR 16 5
BAT 9 3 BAT 9 3 BAT 9 3
LG 1 LG 1 LG 1
(Note) (Note) (Note)
SD Plate 9 SD Plate 9 SD Plate 9
Note. Always make connection for use in an absolute position detection system.
This wiring is not needed for use in an incremental system.
When fabricating an encoder cable, use the recommended wires given in section 15.2.1 and the MR-
J2CNM connector set for encoder cable fabrication, and fabricate an encoder cable as shown in the
following wiring diagram. Referring to this wiring diagram, you can fabricate an encoder cable of up to
50m(164.0ft) length including the length of the encoder cable supplied to the servo motor.
When the encoder cable is to be fabricated by the customer, the wiring of MD and MDR is not required.
Refer to chapter 3 of the servo motor instruction guide and choose the encode side connector according to
the servo motor installation environment.
For use of AWG22
Servo amplifier side Encoder side
(3M)
P5 19 7
LG 11
P5 20
LG 12
P5 18
LG 2
8
MR 7 1
MRR 17 2
BAT 9 3
LG 1
(Note)
SD Plate 9
Note. Always make connection for use in an absolute position detection system.
This wiring is not needed for use in an incremental system.
15 - 21
(b) MR-JHSCBL M-L MR-JHSCBL M-H MR-ENCBL M-H

These encoder cables are used with the HC-SFS HC-RFS HC-UFS2000r/min series servo motors.
1) Model explanation
Model: MR-JHSCBL M-
Symbol Specifications
L Standard flexing life
H Long flexing life
Symbol Cable length [m(ft)]

2 2 (6.56)
5 5 (16.4)
10 10 (32.8)
20 20 (65.6)
30 30 (98.4)
40 40 (131.2)
50 50 (164.0)
Note. MR-JHSCBL M-L has
no 40(131.2) and 50m(164.0ft) sizes.
Model: MR-ENCBL M-H
Long flexing life
Symbol Cable length [m(ft)]

2 2 (6.56)
5 5 (16.4)
10 10 (32.8)
20 20 (65.6)
30 30 (98.4)
40 40 (131.2)
50 50 (164.0)
2) Connection diagram
For the pin assignment on the servo amplifier side, refer to section 4.3.1.
Servo amplifier
Encoder connector Encoder connector Pin Signal Pin Signal
Encoder cable Servo motor A MD K
M AB
(Optional or fabricated) L C B MDR L
N
C MR M
KT P D
J D MRR N SHD
CN2 Encoder S E
R E P
H G F F BAT R LG
G LG S P5
50m(164.0ft) max. H T
J
15 - 22
MR-JHSCBL2M-L MR-JHSCBL10M-L MR-JHSCBL10M-H

MR-JHSCBL5M-L to to
MR-JHSCBL2M-H MR-JHSCBL30M-L MR-JHSCBL50M-H
MR-JHSCBL5M-H MR-ENCBL10M-H
MR-ENCBL2M-H to
MR-ENCBL5M-H MR-ENCBL50M-H
Servo amplifier side Encoder side Servo amplifier side Encoder side Servo amplifier side Encoder side
P5 19 S P5 19 S P5 19 S
LG 11 LG 11 LG 11
P5 20 P5 20 P5 20
LG 12 R LG 12 LG 12
MR 7 C P5 18 P5 18
MRR 17 D LG 2 LG 2
P5 18
LG 2 R R
BAT 9 F MR 7 C MR 7 C
LG 1 G MRR 17 D MRR 17 D
(Note1)
SD Plate N
BAT 9 F BAT 9 F
(Note2) Use of AWG24
LG 1 G LG 1 G
(Less than 10m(32.8ft))
(Note1) (Note1)
Note 1. This wiring is required for use in the absolute SD Plate N SD Plate N
position detection system. This wiring is not
Use of AWG22 Use of AWG24
needed for use in the incremental system.
(10m(32.8ft) to 50m(164.0ft)) (10m(32.8ft) to 50m(164.0ft))
2. AWG28 can be used for 5m(16.4ft) or less.
When fabricating an encoder cable, use the recommended wires given in section 15.2.1 and the MR-
J2CNS connector set for encoder cable fabrication, and fabricate an encoder cable in accordance with
the optional encoder cable wiring diagram given in this section. You can fabricate an encoder cable of
up to 50m(164.0ft) length.
Refer to chapter 3 of the servo motor instruction guide and choose the encode side connector according
to the servo motor installation environment.
15 - 23
(3) Communication cable (MR-JRCATCBL3M)
POINT
This cable may not be used with some personal computers. After fully
examining the signals of the RS-232C connector, refer to this section and
fabricate the cable.
Select the communication cable according to the shape of the RS-232C connector of the personal
computer used. When fabricating the cable, refer to the connection diagram in this section.
(a) Fabricating instructions

The following must be observed in fabrication.
1) Always use a shielded, multi-core cable and connect the shield with FG securely.
2) The optional communication cable is 3m (9.8 ft) long. When the cable is fabricated, its maximum
length is 15m (49 ft) in offices of good environment with minimal noise.
(b) Outline drawing
A B 5 9
1 2
3 4
1 6
View A
View B
3m(9.8ft)
(c) Connection diagram

Personal computer
side CC-Link unit
TXD 3 2 RXD
RXD 2 4 TXD
GND 5 1 GND
RTS 7
CTS 8 3 SD
DSR 6
DTR 4
D-SUB9 pins
15 - 24
15.1.5 Junction terminal block (MR-TB20)
POINT
When using the junction terminal block, you cannot use SG of CN1A-20
and CN1B-20. Use SG of CN1A-4 and CN1B-4.
(1) How to use the junction terminal block

Always use the junction terminal block (MR-TB20) with the junction terminal block cable (MR-J2TBL
M) as a set. A connection example is shown below.
Servo amplifier
Junction terminal block
Cable clamp
MR-TB20
(AERSBAN- ESET)
CN1A
or
CN1B Junction terminal
block cable
(MR-J2TBL M)
Ground the junction terminal block cable on the junction terminal block side with the standard
accessory cable clamp fitting (AERSBAN ESET). For the use of the cable clamp fitting, refer to
section 15.2.6, (2)(c).
(2) Terminal labels

The junction terminal block does not include the terminal block labels which indicate the signal
layouts for MR-J2S-CP-S084. Cut off the terminal block label in Appendix 2 at the dotted line and fold
it up at the centerline for use.
1) For CN1A 2) For CN1B
LG COM OPC LG VDD P15R COM
10
11
12
13
14
15
16
17
18
19
10
11
12
13
14
15
16
17
18
19
P15R SG SD SG SD
0
(3) Outline drawing

[Unit: mm]
126(4.96) ([Unit: in.])
117(4.61)
B1 B10
50(1.97)
60(2.36)
A1 A10
MITSUBISHI
MR-TB20
10 11 12 13 14 15 16 17 18 19
Terminal
block No.
0 1 2 3 5 6 7 8 9 2- 4.5(0.18)
4
46.2(1.82)
Terminal screw: M3.5

Applicable cable: Max. 2mm 2
(0.28)
(Crimping terminal width: 7.2mm (0.283 in) max.)

7
15 - 25
(4) Junction terminal block cable (MR-J2TBL M)

Model : MR-J2TBL M
Symbol Cable length[m(ft)]

05 0.5 (1.64)
1 1 (3.28)
Junction terminal block side connector (Hirose Electric) Servo amplifier side (CN1A CN1B) connector (3M)
HIF3BA-20D-2.54R (connector) 10120-6000EL (connector)
10320-3210-000 (shell kit)
(Note)
Terminal block label Junction terminal
block terminal Pin No. Pin No.
For CN1A For CN1B No.
LG LG 10 B1 1
0 A1 2
VDD 11 B2 3
P15R 1 A2 4
12 B3 5
2 A3 6
13 B4 7
3 A4 8
COM 14 B5 9
SG SG 4 A5 10
OPC P15R 15 B6 11
5 A6 12
COM 16 B7 13
6 A7 14
17 B8 15
7 A8 16
18 B9 17
8 A9 18
19 B10 19
SD SD 9 A10 20
Plate
Note. In the blank, any signal can be set using the parameter.
15.1.6 Battery (MR-BAT, A6BAT)
POINT
The revision (Edition 44) of the Dangerous Goods Rule of the
International Air Transport Association (IATA) went into effect on
January 1, 2003 and was enforced immediately. In this rule, "provisions of
the lithium and lithium ion batteries" were revised to tighten the
restrictions on the air transportation of batteries. However, since this
battery is non-dangerous goods (non-Class 9), air transportation of 24 or
less batteries is outside the range of the restrictions. Air transportation of
more than 24 batteries requires packing compliant with the Packing
Standard 903. When a self-certificate is necessary for battery safety tests,
contact our branch or representative. For more information, consult our
branch or representative. (As of September, 2007).
Use the battery to build an absolute position detection system.

+
-
15 - 26
15.2 Auxiliary equipment
Always use the devices indicated in this section or equivalent. To comply with the EN Standard or UL/C-
UL (CSA) Standard, use the products which conform to the corresponding standard.
15.2.1 Recommended wires
(1) Wires for power supply wiring

The following diagram shows the wires used for wiring. Use the wires given in this section or
equivalent.
1) Main circuit power supply lead 3) Motor power supply lead

Power supply
L1 U U
L2 V V
L3 W W Motor
L11
6) Power regeneration L21 5) Electromagnetic
converter lead 2) Control power supply lead brake lead
Electro-
Power regeneration N B1 magnetic
converter
B2 brake
Regenerative option
C
Encoder
P
4) Regenerative option lead Encoder cable (refer to section 15.1.4)
MR-J2S-T01
CC-Link cable, (refer to section 15.2.1(3))
The following table lists wire sizes. The wires used assume that they are 600V vinyl wires and the
wiring distance is 30m(98.4ft) max. If the wiring distance is over 30m(98.4ft), choose the wire size in
consideration of voltage drop.
The alphabets (a, b, c) in the table correspond to the crimping terminals (Table 15.2) used to wire the
servo amplifier. For connection with the terminal block TE2 of the MR-J2S-100CP-S084 or less, refer
to section 4.11.
The servo motor side connection method depends on the type and capacity of the servo motor. Refer to
section 4.8.
To comply with the UL/C-UL (CSA) Standard, use UL-recognized copper wires rated at 60 (140 ) or
more for wiring.
15 - 27
Table 15.1 Recommended wires

(Note 1) Wires [mm2]
Servo amplifier
1) L1 L2 L3 2) L11 L21 3) U V W 4) P C 5) B1 B2
MR-J2S-10CP(1)-S084
MR-J2S-20CP(1)-S084
MR-J2S-40CP(1)-S084 1.25 (AWG16) : a
2 (AWG14) : a
MR-J2S-60CP-S084
MR-J2S-70CP-S084
2 (AWG14) : a
MR-J2S-100CP-S084 1.25 (AWG16) 2 (AWG14) : a 1.25 (AWG16)
MR-J2S-200CP-S084 3.5 (AWG12) : b 3.5 (AWG12) : b
(Note 2)
MR-J2S-350CP-S084
5.5 (AWG10) : b 5.5 (AWG10) : b
MR-J2S-500CP-S084 5.5 (AWG10) : b
MR-J2S-700CP-S084 8 (AWG8) : c 8 (AWG8) : c 3.5(AW12) : c
Note 1. For the crimping terminals and applicable tools, refer to table 15.2.
2. 3.5mm2 for use of the HC-RFS203 servo motor.
Use wires 6) of the following sizes with the power regeneration converter (FR-RC).
Model Wires[mm2]
FR-RC-15K 14(AWG6)
Table 15.2 Recommended crimping terminals

Servo amplifier side crimping terminals
Symbol
Crimping terminal Applicable tool Manufacturer
a 32959 47387 Tyco Electronics
b EVD5.5-4 YNT-1210S
Body YF-1 E-4 Japan Solderless
c FVD8-5 Head YNE-38 Terminal
Die DH-111 DH-121
15 - 28
(2) Wires for cables

When fabricating a cable, use the wire models given in the following table or equivalent.
Table 15.3 Wires for option cables

Characteristics of one core (Note 3)
Length Core size Number
Type Model Structure Conductor Insulation coating Finishing Wire model
[m(ft)] [mm2] of Cores
[Wires/mm] resistance[ /mm] ODd[mm] (Note 1) OD [mm]
2 to 10 12 UL20276 AWG#28
0.08 7/0.127 222 0.38 5.6
(6.56 to 32.8) (6 pairs) 6pair (BLACK)
MR-JCCBL M-L
20 30 12 UL20276 AWG#22
0.3 12/0.18 62 1.2 8.2
(65.6 98.4) (6 pairs) 6pair (BLACK)
2 5 12 (Note 2)
0.2 40/0.08 105 0.88 7.2
(6.56 16.4) (6 pairs) A14B2343 6P
MR-JCCBL M-H
10 to 50 14 (Note 2)
0.2 40/0.08 105 0.88 8.0
(32.8 to 164) (7 pairs) A14B0238 7P
2 5 8 UL20276 AWG#28
0.08 7/0.127 222 0.38 4.7
(6.56 16.4) (4 pairs) 4pair (BLACK)
Encoder cable MR-JHSCBL M-L
10 to 30 12 UL20276 AWG#22
0.3 12/0.18 62 1.2 8.2
(32.8 to 98.4) (6 pairs) 6pair (BLACK)
2 5 8 (Note 2)
0.2 40/0.08 105 0.88 6.5
(6.56 16.4) (4 pairs) A14B2339 4P
MR-JHSCBL M-H
10 to 50 12 (Note 2)
0.2 40/0.08 105 0.88 7.2
(32.8 to 164) (6 pairs) A14B2343 6P
2 5 8 (Note 2)
0.2 40/0.08 105 0.88 6.5
(6.56 16.4) (4 pairs) A14B2339 4P
MR-ENCBL M-H
10 to 50 12 (Note 2)
0.2 40/0.08 105 0.88 7.2
(32.8 to 164) (6 pairs) A14B2343 6P
Communication 6 UL20276 AWG#28
MR-CPCATCBL3M 3 (9.84) 0.08 7/0.127 222 0.38 4.6
cable (3 pairs) 3pair (BLACK)
Note 1. d is as shown below.
d
Conductor Insulation sheath
2. Purchased from Toa Electric Industry

3. Standard OD. Max. OD is about 10% greater.
15 - 29
(3) CC-Link twisted cable
POINT
For the cables other than the one indicated here, refer to the open field
network CC-Link catalog (L(NA)74108143).
The specifications of the twisted cable usable in CC-Link and the recommended cable are indicated
below. If the cable used is other than the recommended cable indicated in the following table, we
cannot guarantee the performance of CC-Link. For any inquiry, please contact your nearest
Mitsubishi Electric System Service Co., Ltd.
Item Specifications
Model FANC-110SBH
Manufacturer Kuramo Electric
Application For fixed parts
Size 20AWG 3
Insulator material Polyethylene foam
Sheath
Insulator color Blue, white, and yellow
Braided screen
Sheath material Oil resistant vinyl Tape
Sheath color Brown Insulator
Operating temperature range (Note) 0 to 75 (32 to 167 ) Conductor
Tensile strength 49N Inclusion
Minimum bend radius 35mm Ground wire
Outline dimension Approx. 7.6mm
Approximate mass 70kg/km Fig. 15.1 Structure
Conductor resistance (20 ) 34.5 /km or lower
Characteristic impedance 110 15
UL AWM Style 2464
Applicable specification CAN/CSA-C22.2
No.210.2-M90(cUL)
Note. An upper limit of the operating temperature range shows a heat-resistant temperature of the cable material.
In high-temperature environment, the transmittable distance may be reduced.
15.2.2 No-fuse breakers, fuses, magnetic contactors
Always use one no-fuse breaker and one magnetic contactor with one servo amplifier. When using a fuse
instead of the no-fuse breaker, use the one having the specifications given in this section.
Fuse
Servo amplifier No-fuse breaker Magnetic contactor
Class Current [A] Voltage [V]
MR-J2S-10CP(1)-S084 30 frame 5A K5 10
MR-J2S-20CP-S084 30 frame 5A K5 10
MR-J2S-40CP-S084 20CP1-S084 30 frame 10A K5 15
S-N10
MR-J2S-60CP-S084 40CP1-S084 30 frame 15A K5 20
MR-J2S-70CP-S084 30 frame 15A K5 20
250AC
MR-J2S-100CP-S084 30 frame 15A K5 25
MR-J2S-200CP-S084 30 frame 20A K5 40 S-N18
15 - 30
15.2.3 Power factor improving reactors
The input power factor is improved to be about 90%. For use with a 1-phase power supply, it may be
slightly lower than 90%.
[Unit : mm] Servo amplifier

MR-J2S- CP-S084
([Unit : in.]) NFB
MC FR-BAL
R X L1
3-phase S Y
L2
H 5(0.2)
200 to 230VAC
T Z
L3
Servo amplifier
MR-J2S- CP-S084
NFB
MC FR-BAL
(Note) R X L1
W D1
1-phase S Y
Installation screw 230VAC L2
T Z
L3
D 5(0.2)
RXSY T Z Servo amplifier

MR-J2S- CP1-S084
NFB
MC FR-BAL
C W1 1-phase R X L1
100 to 120VAC S Y
L2
T Z
Note. Connect a 1-phase 230VAC power supply to L1/L2 and keep L3 open.
Dimensions [mm (in) ] Mounting Terminal Mass

Servo amplifier Model
W W1 H D D1 C screw size screw size [kg (lb)]
0
MR-J2S-10CP(1)-S084/ 45-2.5
FR-BAL-0.4K 135 (5.31) 120 (4.72) 115 (4.53) 59 (2.32) 0 7.5 (0.29) M4 M3.5 2.0 (4.4)
20CP-S084 (1.77-0.098 )
0
MR-J2S-40CP-S084/ 57-2.5
FR-BAL-0.75K 135 (5.31) 120 (4.72) 115 (4.53) 69 (2.72) 0 7.5 (0.29) M4 M3.5 2.8 (6.17)
20CP1-S084 (2.24-0.098 )
0
MR-J2S-60CP-S084/ 55-2.5
FR-BAL-1.5K 160 (6.30) 145 (5.71) 140 (5.51) 71 (2.79) 0 7.5 (0.29) M4 M3.5 3.7 (8.16)
70CP-S084/ 40CP1-S084 (2.17-0.098 )
0
75-2.5
MR-J2S-100CP-S084 FR-BAL-2.2K 160 (6.30) 145 (5.71) 140 (5.51) 91 (3.58) 0 7.5 (0.29) M4 M3.5 5.6 (12.35)
(2.95-0.098 )
0
70-2.5
MR-J2S-200CP-S084 FR-BAL-3.7K 220 (8.66) 200 (7.87) 192 (7.56) 90 (3.54) 0 10 (0.39) M5 M4 8.5 (18.74)
(2.76-0.098 )
0
100-2.5
MR-J2S-350CP-S084 FR-BAL-7.5K 220 (8.66) 200 (7.87) 194 (7.64) 120 (4.72) 0 10 (0.39) M5 M5 14.5 (32.0)
(3.94-0.098 )
0
100-2.5
MR-J2S-500CP-S084 FR-BAL-11K 280 (11.02) 255 (10.04) 220 (8.66) 135 (5.31) 0 12.5 (0.49) M6 M6 19 (41.9)
(3.94-0.098 )
0
110-2.5
MR-J2S-700CP-S084 FR-BAL-15K 295 (11.61) 270 (10.62) 275 (10.83) 133 (5.24) 0 12.5 (0.49) M6 M6 27 (59.5)
(4.33-0.098 )
15 - 31
15.2.4 Relays
The following relays should be used with the interfaces.
Interface Selection example

Relay used for input signals (interface DI-1) signals To prevent defective contacts , use a relay for small signal
(twin contacts).
(Ex.) Omron : type G2A , MY
Relay used for digital output signals (interface DO-1) Small relay with 12VDC or 24VDC of 40mA or less
(Ex.) Omron : type MY
15.2.5 Surge absorbers
A surge absorber is required for the electromagnetic brake. Use the following surge absorber or equivalent.
Insulate the wiring as shown in the diagram.
Maximum rating Static

Maximum capacity Varistor voltage
Permissible circuit Surge Energy Rated limit voltage rating (range) V1mA
(reference
voltage immunity immunity power
value)
AC[Vma] DC[V] [A] [J] [W] [A] [V] [pF] [V]
(Note) 220
140 180 5 0.4 25 360 300
500/time (198 to 242)
Note. 1 time 8 20 s
(Example) ERZV10D221 (Matsushita Electric Industry)

TNR-10V221K (Nippon chemi-con)
Outline drawing [mm] ( [in] ) (ERZ-C10DK221)
13.5 (0.53) 4.7 1.0 (0.19 0.04)

(0.65)
16.5
Vinyl tube
3.0 (0.12)
or less
30.0 (1.18)
or more
0.8 (0.03) Crimping terminal

for M4 screw
15 - 32
15.2.6 Noise reduction techniques
Noises are classified into external noises which enter the servo amplifier to cause it to malfunction and
those radiated by the servo amplifier to cause peripheral devices to malfunction. Since the servo amplifier
is an electronic device which handles small signals, the following general noise reduction techniques are
required.
Also, the servo amplifier can be a source of noise as its outputs are chopped by high carrier frequencies. If
peripheral devices malfunction due to noises produced by the servo amplifier, noise suppression measures
must be taken. The measures will vary slightly with the routes of noise transmission.
(1) Noise reduction techniques

(a) General reduction techniques
Avoid laying power lines (input and output cables) and signal cables side by side or do not bundle
them together. Separate power lines from signal cables.
Use shielded, twisted pair cables for connection with the encoder and for control signal
transmission, and connect the shield to the SD terminal.
Ground the servo amplifier, servo motor, etc. together at one point (refer to section 4.10).
(b) Reduction techniques for external noises that cause the servo amplifier to malfunction
If there are noise sources (such as a magnetic contactor, an electromagnetic brake, and many
relays which make a large amount of noise) near the servo amplifier and the servo amplifier may
malfunction, the following countermeasures are required.
Provide surge absorbers on the noise sources to suppress noises.
Attach data line filters to the signal cables.
Ground the shields of the encoder connecting cable and the control signal cables with cable clamp
fittings.
Although a surge absorber is built into the servo amplifier, to protect the servo amplifier and
other equipment against large exogenous noise and lightning surge, attaching a varistor to the
power input section of the equipment is recommended.
15 - 33
(c) Techniques for noises radiated by the servo amplifier that cause peripheral devices to malfunction
Noises produced by the servo amplifier are classified into those radiated from the cables connected
to the servo amplifier and its main circuits (input and output circuits), those induced
electromagnetically or statically by the signal cables of the peripheral devices located near the
main circuit cables, and those transmitted through the power supply cables.
Noises by servo Noises transmitted Noise radiated directly

amplifier in the air from servo amplifier Route 1)
Noise radiated from the

power supply cable Route 2)
Noise radiated from

servo motor cable Route 3)
Magnetic induction
noise Routes 4) and 5)
Static induction
noise Route 6)
Noises transmitted
Noise transmitted through
through electric Route 7)
power supply cable
channels
Noise sneaking from

grounding cable due to Route 8)
leakage current
5)
7) 7)
2)
7)
Sensor
power
1) supply
Servo
2)
amplifier
Instrument Receiver
3)
8)
6)
4) Sensor
3)
Servo motor M
15 - 34
Noise transmission route Suppression techniques

When measuring instruments, receivers, sensors, etc. which handle weak signals and may
malfunction due to noise and/or their signal cables are contained in a control box together with the
servo amplifier or run near the servo amplifier, such devices may malfunction due to noises
transmitted through the air. The following techniques are required.
1. Provide maximum clearance between easily affected devices and the servo amplifier.
1) 2) 3) 2. Provide maximum clearance between easily affected signal cables and the I/O cables of the servo
amplifier.
3. Avoid laying the power lines (Input cables of the servo amplifier) and signal cables side by side or
bundling them together.
4. Insert a line noise filter to the I/O cables or a radio noise filter on the input line.
5. Use shielded wires for signal and power cables or put cables in separate metal conduits.
When the power lines and the signal cables are laid side by side or bundled together, magnetic
induction noise and static induction noise will be transmitted through the signal cables and
malfunction may occur. The following techniques are required.
1. Provide maximum clearance between easily affected devices and the servo amplifier.
4) 5) 6) 2. Provide maximum clearance between easily affected signal cables and the I/O cables of the servo
amplifier.
3. Avoid laying the power lines (Input cables of the servo amplifier) and signal cables side by side or
bundling them together.
4. Use shielded wires for signal and power cables or put the cables in separate metal conduits.
When the power supply of peripheral devices is connected to the power supply of the servo
amplifier system, noises produced by the servo amplifier may be transmitted back through the
7) power supply cable and the devices may malfunction. The following techniques are required.
1. Insert the radio noise filter (FR-BIF) on the power cables (Input cables) of the servo amplifier.
2. Insert the line noise filter (FR-BSF01 FR-BLF) on the power cables of the servo amplifier.
When the cables of peripheral devices are connected to the servo amplifier to make a closed loop
8) circuit, leakage current may flow to malfunction the peripheral devices. If so, malfunction may be
prevented by disconnecting the grounding cable of the peripheral device.
(2) Noise reduction products

(a) Data line filter
Noise can be prevented by installing a data line filter onto the encoder cable, etc.
For example, the ZCAT3035-1330 of TDK and the ESD-SR-25 of NEC Tokin make are available as
data line filters.
As a reference example, the impedance specifications of the ZCAT3035-1330 (TDK) are indicated
below.
This impedances are reference values and not guaranteed values.
Impedance[ ] [Unit: mm]([Unit: in.])

10 to 100MHz 100 to 500MHz
30 1 (0.51 0.04)
80 150 39 1(1.54 0.04) Loop for fixing the

34 1 cable band
13 1
(1.34 0.04)
(1.18 0.04)
TDK
Product name Lot number
Outline drawing (ZCAT3035-1330)
15 - 35
(b) Surge suppressor

The recommended surge suppressor for installation to an AC relay, AC valve, AC electromagnetic
brake or the like near the servo amplifier is shown below. Use this product or equivalent.
MC
Relay
Surge suppressor
Surge suppressor
Surge suppressor This distance should be short

(within 20cm(0.79 in.)).
(Ex.) 972A.2003 50411
(Matsuo Electric Co., Ltd. 200VAC rating)
Rated Outline drawing [Unit: mm] ([Unit: in.])
voltage C [ F] R [Ω] Test voltage AC[V] Vinyl sheath 18 1.5
AC[V] (0.71 0.06)
Blue vinyl cord Red vinyl cord
50 Across 6(0.24)
200 0.5
(1W) T-C 1000(1 to 5s)
10(0.39)or less 10(0.39)or less

4(0.16)
10 3 15 1(0.59 0.04) 10 3 31(1.22)
(0.39 (0.39
0.12) 200(7.87) 48 1.5 200(7.87) 0.15)
or more (1.89 0.06) or more
Note that a diode should be installed to a DC relay, DC valve or

the like. RA
Maximum voltage: Not less than 4 times the drive voltage of
the relay or the like Diode
Maximum current: Not less than twice the drive current of
the relay or the like
(c) Cable clamp fitting (AERSBAN- SET)

Generally, the earth of the shielded cable may only be connected to the connector's SD terminal.
However, the effect can be increased by directly connecting the cable to an earth plate as shown
below.
Install the earth plate near the servo amplifier for the encoder cable. Peel part of the cable sheath
to expose the external conductor, and press that part against the earth plate with the cable clamp.
If the cable is thin, clamp several cables in a bunch.
The clamp comes as a set with the earth plate.
Cable
Cable clamp
(A,B) Earth plate
40(1.57)
Strip the cable sheath of

the clamped area. cutter
cable External conductor

Clamp section diagram
15 - 36
Outline drawing
[Unit: mm]
([Unit: in.])
Earth plate Clamp section diagram
2- 5(0.20) hole 17.5(0.69)

installation hole
30(1.18)
L or less 10(0.39)
B 0.3(0.01)
(0.940)
A
C
6 (0.24)
3 (0.12)
35 (1.38)
7 (0.28)
0.2
(0.940)
0
0.3
0
24
24
(Note)M4 screw 6 22(0.87)
(0.24) 35(1.38)
11(0.43)
Note. Screw hole for grounding. Connect it to the earth plate of the control box.
Type A B C Accessory fittings Clamp fitting L

100 86 30 70
AERSBAN-DSET clamp A: 2pcs. A
(3.94) (3.39) (1.18) (2.76)
70 56 45
AERSBAN-ESET clamp B: 1pc. B
(2.76) (2.20) (1.77)
15 - 37
(d) Line noise filter (FR-BLF, FR-BSF01)

This filter is effective in suppressing noises radiated from the power supply side and output side of
the servo amplifier and also in suppressing high-frequency leakage current (zero-phase current)
especially within 0.5MHz to 5MHz band.
Connection diagram Outline drawing [Unit: mm] ([Unit: in.])

Use the line noise filters for wires of the main power supply FR-BSF01(for MR-J2S-200CP-S084 or less)
(L1 L2 L3) and of the motor power supply (U V W). Pass Approx.110(4.33)
each of the 3-phase wires through the line noise filter an equal
95 0.5(3.74 0.02) 2- 5(0.20)
number of times in the same direction. For the main power supply,
Approx 22.5(0.89)
the effect of the filter rises as the number of passes increases, but
0.02)
generally four passes would be appropriate. For the motor power
supply, passes must be four times or less. Do not pass the
11.25 0.5
(0.44
Approx.65(2.56)
grounding (earth) wire through the filter, or the effect of the filter
33(1.30)
will drop. Wind the wires by passing through the filter to satisfy the
required number of passes as shown in Example 1. If the wires
Approx.65(2.56)
are too thick to wind, use two or more filters to have the required
number of passes as shown in Example 2. Place the line noise
4.5(0.18)
filters as close to the servo amplifier as possible for their best
performance.
Example 1 NFB MC Servo amplifier
Power FR-BLF(MR-J2S-350CP-S084 or more)
L1
supply 31.5(1.24)
L2 7(0.28)
Line noise
7(0.28)
L3
filter
(Number of turns: 4) 130(5.12)
85(3.35)
Example 2 NFB MC
Servo amplifier
2.3(0.09) 80(3.15)
(1.38)
35
Power
L1
supply
160(6.30)
L2
180(7.09)
Line noise L3
filter
Two filters are used
(Total number of turns: 4)
(e) Radio noise filter (FR-BIF)...for the input side only

This filter is effective in suppressing noises radiated from the power supply side of the servo
amplifier especially in 10MHz and lower radio frequency bands. The FR-BIF is designed for the
input only.
Connection diagram Outline drawing (Unit: mm) ([Unit: in.])

Make the connection cables as short as possible. Leakage current: 4mA
Grounding is always required. Red White Blue Green
About 300(11.81)
When using the FR-BIF with a single-phase cable, be sure to

insulate the cables not used for wiring.
NFB MC Servo amplifier
L1
Power 29 (1.14)
L2
supply
42 (1.65)
5 (0.20)
4 (0.16)
L3 hole
Radio noise 58 (2.28) 29 (1.14)

7 (0.28)
filter FR-BIF
44 (1.73)
15 - 38
(f) Varistors for input power supply (Recommended)

Varistors are effective to prevent exogenous noise and lightning surge from entering the servo
amplifier. When using a varistor, connect it between each phase of the input power supply of the
equipment. For varistors, the TND20V-431K and TND20V-471K, manufactured by NIPPON
CHEMI-CON, are recommended. For detailed specification and usage of the varistors, refer to the
manufacturer catalog.
Maximum rating Static

Varistor voltage
Rated Maximum limit capacity
Permissible circuit Surge current Energy rating (range)
Varistor pulse voltage (reference
voltage immunity immunity V1mA
power value)
AC[Vrms] DC[V] 8/20 s[A] 2ms[J] [W] [A] [V] [pF] [V]
TND20V-431K 275 350 10000/1 time 195 710 1300 430(387 to 473)
1.0 100
TND20V-471K 300 385 7000/2 time 215 775 1200 470(423 to 517)
[Unit: mm]
D H T E (Note)L d W
D T Model
Max. Max. Max. 1.0 min. 0.05 1.0
TND20V-431K 6.4 3.3
21.5 24.5 20 0.8 10.0
H
TND20V-471K 6.6 3.5

Note. For special purpose items for lead length (L), contact the manufacturer.
W E
L
15 - 39
15.2.7 Leakage current breaker
(1) Selection method

High-frequency chopper currents controlled by pulse width modulation flow in the AC servo circuits.
Leakage currents containing harmonic contents are larger than those of the motor which is run with a
commercial power supply.
Select a leakage current breaker according to the following formula, and ground the servo amplifier,
servo motor, etc. securely.
Make the input and output cables as short as possible, and also make the grounding cable as long as
possible (about 30cm (11.8 in)) to minimize leakage currents.
Rated sensitivity current 10 {Ig1 Ign Iga K (Ig2 Igm)} [mA] ..........(15.1)
Cable K: Constant considering the harmonic contents

Leakage current breaker
K
Type Mitsubishi products
NV Noise
filter NV-SP
Servo Cable
M Models provided with NV-SW
amplifier
harmonic and surge NV-CP 1
reduction techniques NV-CW
NV-HW
Ig1 Ign Iga Ig2 Igm
BV-C1
General models NFB 3
NV-L
Ig1: Leakage current on the electric channel from the leakage current breaker to the input terminals
of the servo amplifier (Found from Fig. 15.2.)
Ig2: Leakage current on the electric channel from the output terminals of the servo amplifier to the
servo motor (Found from Fig. 15.2.)
Ign: Leakage current when a filter is connected to the input side (4.4mA per one FR-BIF)
Iga: Leakage current of the servo amplifier (Found from Table 15.5.)
Igm: Leakage current of the servo motor (Found from Table 15.4.)
Table 15.4 Servo motor's Table 15.5 Servo amplifier's

120
leakage current leakage current
100 example (Igm) example (Iga)
Leakage current
Servo motor Leakage Servo amplifier Leakage

80 power [kW] current [mA] capacity [kW] current [mA]
0.05 to 0.5 0.1 0.1 to 0.6 0.1
60
0.6 to 1.0 0.1 0.7 to 3.5 0.15
40 1.2 to 2.2 0.2 5 7 2
[mA] 3 to 3.5 0.3
20
5 0.5
0
2 3.5 8 1422 38 80 150 7 0.7 Table 15.6 Leakage circuit breaker selection example
5.5 30 60 100 Rated sensitivity
Cable size[mm2] Servo amplifier current of leakage
Fig. 15.2 Leakage current example circuit breaker [mA]
(Ig1, Ig2) for CV cable run MR-J2S-10CP-S084 to
in metal conduit MR-J2S-350CP-S084
15
MR-J2S-10CP1-S084 to
MR-J2S-40CP1-S084
MR-J2S-500CP-S084 30
MR-J2S-700CP-S084 50
15 - 40
(2) Selection example

Indicated below is an example of selecting a leakage current breaker under the following conditions.
2mm2 5m(196.85inch) 2mm2 5m(196.85inch)
NV
Servo
amplifier
MR-J2S-40CP M HC-MFS43
-S084
Ig1 Iga Ig2 Igm
Use a leakage current breaker designed for suppressing harmonics/surges.

Find the terms of Equation (15.1) from the diagram.
5
Ig1 20 0.1 [mA]
1000
5
Ig2 20 0.1 [mA]
1000
Ign 0 (not used)
Iga 0.1 [mA]
Igm 0.1 [mA]
Insert these values in Equation (15.1).
Ig 10 {0.1 0 0.1 1 (0.1 0.1)}
4 [mA]
According to the result of calculation, use a leakage current breaker having the rated sensitivity
current (Ig) of 4[mA] or more. A leakage current breaker having Ig of 15[mA] is used with the NV-
SP/CP/ SW/CW/HW series.
15 - 41
15.2.8 EMC filter
For compliance with the EMC Directive of the EN Standard, it is recommended to use the following filter.
Some EMC filters are large in leakage current.
(1) Combination with the servo amplifier

Recommended filter
Servo amplifier Mass [kg]([lb])
Model Leakage current [mA]
MR-J2S-10CP-S084 to MR-J2S-100CP-S084
SF1252 38 0.75 (1.65)
MR-J2S-200CP-S084 MR-J2S-350CP-S084 SF1253 57 1.37 (1.65)
MR-J2S-500CP-S084 (Note) HF-3040A-TM 1.5 5.5 (12.13)
MR-J2S-700CP-S084 (Note) HF-3050A-TM 1.5 6.7 (14.77)
Note. Soshin Electric. A surge protector is separately required to use any of these EMC filters. (Refer to the EMC Installation
Guidelines.)

EMC filter EMC filter
(SF1252, SF1253) Servo amplifier (SOSHIN Electric Co., Ltd) Servo amplifier
NFB LINE LOAD MC NFB MC
L1 L1 L1 1 4 L1
(Note 1) (Note 1)
Power L2 L2 L2 Power 2 5 L2
supply supply
L3 L3 L3 3 6 L3
(Note 2)
L11 E L11
L21 L21
1 Surge protector 1
(RAV-781BYZ-2)
2
(OKAYA Electric Industries
3 Co., Ltd.)
1 2 3 Surge protector 2
(RAV-781BXZ-4)
(OKAYA Electric Industries Co., Ltd.)
Note 1. For 1-phase 230VAC power supply, connect the power supply to L1,L2 and leave L3 open.
There is no L3 for 1-phase 100 to 120VAC power supply.
2. Connect when the power supply has earth.
15 - 42
(3) Outline drawing

(a) EMC filter
[Unit: mm(in)]
SF1252 SF1253
149.5(5.886) 6.0(0.236) 209.5(8.248) 6.0(0.236)
L1
L2 LINE L1
L2 LINE
L3 L3
(input side) (input side)
LINE
LINE
168.0(6.614)
156.0(6.142)
140.0(5.512)
168.0(6.614)
156.0(6.142)
140.0(5.512)
LABEL
LABEL
LOAD
LOAD
L1'
L2' LOAD L1'
L2' LOAD
L3'
(output side) L3'
(output side)
8.5 16.0(0.63) 8.5 23.0(0.906)

(0.335) 42.0 (0.335) 49.0
(1.654) (1.929)
HF3040-TM HF-3050A-TM
6-K
3-L 3-L
G 1
D 2
E 1
F 2
J 2
C 1 C 1
H 2
B 2
A 5
Dimensions [mm(in)]
Model
A B C D E F G H J K L M
260 210 85 155 140 125 44 140 70
HF3040A-TM M5 M4
(10.23) (8.27) (3.35) (6.10) (5.51) (4.92) (1.73) (5.51) (2.76) R3.25,
290 240 100 190 175 160 44 170 100 length 8
HF3050A-TM M6 M4
(11.42) (9.45) (3.94) (7.48) (6.89) (6.30) (1.73) (5.51) (3.94)
15 - 43
(b) Surge protector

RAV-781BYZ-2 [Unit: mm]
1) 2) 3)
Black Black Black
5.5 1
11 1
4.2 0.2
28.5 1.0
UL-1015AWG16
30
0
200
1 2 3
4.5 0.5
28 1.0
41 1.0
RAV-781BXZ-4 [Unit: mm]
1) 2) 3) 4)
5.5 1
11 1
4.2 0.2
28.5 1.0
UL-1015AWG16
30
0
200
1 2 3
4.5 0.5
28 1.0
41 1.0
15 - 44
APPENDIX
Instantaneously Effective load Peak load ratio

occurring torque torque
Effective value Peak hold

calculation
App 1. Status indication block diagram
Cumulative Droop pulse Servo motor

command pulse speed Bus voltage
Electronic gear
CMX Position Speed Current
Command generator PWM M Servo motor
CDV control control control
App - 1
Speed feedback
Absolute
Auto position
tuning section encoder
Cumulative Within one- Low

feedback pulse revolution position High ABS counter
Differential
Within one-
revolution position
Current
position ABS counter
calculation
Load inertia
moment ratio
App - 2
10 10 10 10
LG
0 0 0 0
11 11 11 11
1 1 1 1
LG VDD
12 12 12 12
P15R
2 2 2 2
13 13 13 13
3 3 3 3
14 14 14 14
4 4 4 4
SG
SG
15 15 15 15
5 5 5 5
COM OPC
16 16 16 16
6 6 6 6
P15R COM
17 17 17 17
7 7 7 7
18 18 18 18
8 8 8 8
19 19 19 19
9 9 9 9
SD
SD
For CN1B For CN1A
App 2. Junction terminal block (MR-TB20) terminal block labels
APPENDIX
APPENDIX
App 3. Combination of servo amplifier and servo motor
The servo amplifier software versions compatible with the servo motors are indicated in the parentheses.
The servo amplifiers whose software versions are not indicated can be used regardless of the versions.

Servo motor Servo motor
(Software version) (Software version)
MR-J2S-10CP-S084 HC-RFS103 MR-J2S-200CP-S084
HC-KFS053
MR-J2S-10CP1-S084 HC-RFS153 MR-J2S-200CP-S084
HC-KFS13
MR-J2S-10CP1-S084 HC-RFS353 MR-J2S-500CP-S084
HC-KFS23
MR-J2S-20CP1-S084 HC-UFS72 MR-J2S-70CP-S084
MR-J2S-40CP-S084 HC-UFS152 MR-J2S-200CP-S084
HC-KFS43
HC-KFS73 MR-J2S-70CP-S084 HC-UFS352 MR-J2S-500CP-S084
MR-J2S-10CP-S084 HC-UFS502 MR-J2S-500CP-S084
HC-MFS053
MR-J2S-10CP1-S084 MR-J2S-10CP-S084
HC-UFS13
MR-J2S-10CP-S084 MR-J2S-10CP1-S084
HC-MFS13
HC-UFS23
HC-MFS23
HC-UFS43
HC-MFS43
HC-MFS73 MR-J2S-70CP-S084 HC-LFS52 MR-J2S-60CP-S084
HC-SFS81 MR-J2S-100CP-S084 HC-LFS102 MR-J2S-100CP-S084 (Version A1 or later)
HC-SFS121 MR-J2S-200CP-S084 HC-LFS152 MR-J2S-200CP-S084
HC-SFS52 MR-J2S-60CP-S084 HA-LFS502 MR-J2S-500CP-S084
HC-SFS102 MR-J2S-100CP-S084 HA-LFS702 MR-J2S-700CP-S084
HC-SFS152 MR-J2S-200CP-S084
App - 3
APPENDIX
App 4. Change of connector sets to the RoHS compatible products
Connector sets (options) in the following table are changed to the RoHS compatible products after September,
2006 shipment.
Please accept that the current products might be mixed with RoHS compatible products based on availability.
Model Current Product RoHS Compatible Product

MR-J2CNM Amplifier connector (3M or equivalent) Amplifier connector (3M or equivalent)
MR-J2CN1 10120-3000VE (connector) 10120-3000PE (connector)
MR-J2CNS Amplifier connector (3M or equivalent) Amplifier connector (3M or equivalent)
10120-3000VE (connector) 10120-3000PE (connector)
Encoder connector (DDK) Encoder connector (DDK)
MS3057-12A (Cable clump) D/MS3057-12A (Cable clump)
MS3106B20-29S (Straight plug) D/MS3106B20-29S (Straight plug)
MR-ENCNS Amplifier connector (3M or equivalent) Amplifier connector (3M or equivalent)
10120-3000VE (connector) 10120-3000PE (connector)
MS3106A20-29S (D190) (Plug, DDK) D/MS3106A20-29S (D190) (Plug, DDK)
CE3057-12A-3 (D265) (Cable clump, DDK) CE3057-12A-3-D (Cable clump, DDK)
CE02-20BS-S (Back shell, DDK) CE02-20BS-S-D (Back shell, DDK)
MR-PWCNS1 Power supply connector (DDK) Power supply connector (DDK)
CE05-6A22-23SD-B-BSS (Connector and back CE05-6A22-23SD-D-BSS (Connector and back
shell) shell)
CE3057-12A-2 (D265) (Cable clump) CE3057-12A-2-D (Cable clump)
CE05-6A24-24SD-B-BSS (Connector and back CE05-6A24-10SD-B-BSS (Connector and back
shell) shell)
CE05-6A32-17SD-B-BSS (Connector and back CE05-6A32-17SD-D-BSS (Connector and back
shell) shell)
MR-BKCN Electromagnetic brake connector Electromagnetic brake connector
MS3106A10SL-4S (D190) (Plug, DDK) D/MS3106A10SL-4S (D190) (Plug, DDK)
App - 4
REVISIONS
*The manual number is given on the bottom left of the back cover.
Print Data *Manual Number Revision
Jun., 2003 SH(NA)030036-A First edition
Aug., 2004 SH(NA)030036-B Safety Instructions 3.: Sentence change
4. (1): Writing changed in the table
4. (5): Figure change
COMPLIANCE WITH EC DIRECTIVES 2.: Correction to error in writing
CONFORMANCE WITH UL/C-UL STANDARD: Correction to error in writing
Section 1.1: Text partial review
Section 1.1.2: Figure partial correction
Section 1.2: Table item addition
Section 1.3: Partial review of statement in the table
Section 1.4 (1): Figure change
Section 1.4 (2): Remark 1 change
Section 1.5: Remarks change
Section 1.7 (1): (a), (b) Partial review of statement in the table
Section 1.7 (2): Partial review of statement in the table
Section 2.1 (4): Writing changed in the table
Section 3.5.1 (1): Statement addition
Section 3.5.1 (2): Statement change
Section 3.5.2 (3): Correction to error in writing
Section 3.5.3: Partial correction of statement in the table
Figure dimension indication addition, statement review, remarks addition,
correction to error in writing, remarks font change
Section 4.5: Addition to "Caution"
Section 4.5 (3): Writing change
Section 4.6.1: Figure change
Section 4.6.2 (2): Figure change, remarks deletion
Section 4.7.3 (1): Sentence addition
Section 4.8.2: Figure change
Section 4.8.3: Remarks change
Section 4.9: Figure change, statement review
Section 4.9 (1): Figure change
Section 4.9 (2): Statement review
Section 4.9 (3): (d), (e) Figure change, wrong character correction
Section 4.10: Figure partial change
Section 4.11: POINT addition
Section 5.1.2: Caution sentence change
Section 5.1.2 (2): Statement review
Section 5.2.2 (4): Partial sentence change
Section 5.4.2 (3): Timing chart partial addition, sentence change
Section 5.4.6 (2): Sentence change
Aug., 2004 SH(NA)030036-B Section 5.4.7 (2): Timing chart partial addition, sentence change
Section 5.4.11: Timing chart partial addition
Section 5.5 (5): Sentence change
Section 6.1.1: Statement review
Section 6.1.1 (2): Statement addition/correction, parameter No. change,
sentence change in the table
Section 6.2.1: Correction to error in writing
Chapter 7: POINT deletion, statement review
Section 7.2: Statement review, configuration table contents correction
Section 8.2.2: Addition of sentence in the table
Section 8.9: Statement review
Section 10.2 (2): Statement review
Chapter 11: Sentence change
Chapter 12: Statement review
Section 12.4.2: Statement review, sentence addition, addition/change of
indication in the table
Section 12.4.3: Statement review, table item addition
Section 13.1: Correction to error in writing
Section 14.1: Note change
Section 14.3: Graph addition
Section 14.5: Correction to error in writing, review of statement in the table
Chapter 15: Sentence change
Section 15.1.1: Correction to error in writing, table contents addition, POINT
addition, statement addition, outline drawing change, table
contents change
Section 15.1.2: Correction to error in writing, remarks change
Section 15.1.3 (2): Connection diagram change, remarks addition, correction to
error in writing
Section 15.1.4: Change of maker name in the table
Section 15.1.6: POINT addition
Section 15.2.1: Correction to error in writing, remarks font change
Section 15.2.3: Dimension representation change, model name addition,
change of value in the table
Section 15.2.6 (2): Correction to error in writing, connection diagram change,
outline drawing change
Section 15.2.7 (2): Correction to error in writing
Section 15.2.8 (2): Connection diagram change
Section 15.2.8 (3): Outline drawing change
Appendices: Appendix 3 contents review, Appendix 4 addition
Service network: Review
Mar., 2005 SH(NA)030036-C Section 3.5.2 (2): Sentence review
Section 4.5: Caution sentence review
Mar., 2005 SH(NA)030036-C Section 4.8.3 (1): Correction of words and sentences
Section 4.9: Sentence review
Section 5.2.1 (2) (b): Note review
Section 5.5: CAUTION sentence addition (1) Sentence review
Section 6.1.2 (2): No.55 Review of words in the table
Section 7.2 (1): Sentence review
Section 10.4 (1): Correction of words and sentences
Section 12.4.2: Caution sentence addition, Caution sentence review
AL. 17, AL. 19, Sentence addition and review
AL. 33 Sentence addition
Section 15.1.2 (2): Note review
Section 15.1.2 (2) (b): Deletion of words in the figure
Section 15.1.3 (2): Note correction
Section 15.1.4 (1): 1) 6) Correction of words and sentences
Section 15.1.4 (2): 2) Correction of words and sentences
Section 15.1.6: Date change in "POINT"
Section 15.2.1 (1): Table 15.2 Correction of words and sentences
App.5: Correction of telephone No. and date
Jan., 2006 SH(NA)030036-D Safety Instructions (2): Wiring: Sentence addition
Safety Instructions (4): Usage: Sentence addition
Chapter 2: CAUTION addition
Section 3.2.2 (4) (e): Addition of writing on recommended torque screw driver
Section 4.9: CAUTION addition
Section 4.11.1: Addition of descriptions
Section 5.4.10: Correction of Home position return automatic return function
Section 6.1.2 (2): Parameter No.30 Note addition
Section 8.1.1: Addition
Section 12.1: Addition of Fault at Power on
Section 12.1: Change of Test operation status for Servo side alarm occurrence
to “Stop”
Section 12.4.2: AL.72 Addition of Cause
Section 15.2.6 (2) (d): Change of FR-BSF01 outline drawing
Sep., 2006 SH(NA)030036-E Safety Instructions (2): Wiring: Connection diagram change
Section 1.6.3: Caution deletion, Warning addition
Section 3.1: Correction of connection cable in the table
Note change
Section 3.2.1(2): Correction of CC-Link connection cable
Section 3.5.1(1): Correction of the table
Section 3.5.1(2): Correction of the table
Section 3.5.2(3): Correction of Monitor1 in the table
Correction of Monitor2 in the table
Sep., 2006 SH(NA)030036-E Section 3.5.2(3): Correction of Point table No./Speed command data in the
table
Section 3.5.4(1): Sentence review
Correction of the table
Section 3.5.4(2): Sentence review
Chapter 4: CAUTION addition
Section 4.4.2: POINT review
Section 4.7.2: U, V, and W in the table review
Section 4.7.3(3): CAUTION addition
Section 4.8.2: CAUTION addition
Section 5.5(1): Correction of sentence
Section 6.2.1: Correction of POINT
Section 8.2.3: Correction of Command position
Section 12.4.3: Correction of AL.90
Section 13.3(1)(b): Correction of outline dimension drawing
Section 15.1.1(2)(b): Correction of formulas in the table
Section 15.1.5(3): Correction of outline dimension drawing
Sep., 2007 SH(NA)030036-F Safety Instructions
1. To prevent electric shock: Partial change of sentence
2. To prevent fire: Partial change of sentence
4. Additional Instructions
(2) Wiring: Addition of sentence
Section 1.1.2: Addition of Note
Section 1.6.3: POINT: Change of sentence
Section 1.7: Addition of Note
Section 3.5.1(1): Change of Reset device No. RY1A
Section 3.5.1(2): Change of Reserved device No. “RY(n+1)0 to RY(n+1)9” to
“RY(n+1)0 to RY(n+1)F”
Change of Reserved device No. “RXnF to RX(n+1)9” to “RXnF
to RX(n+1)F”
Section 3.5.2(1): Change of device No. in Description of Monitor output
execution demand
Section 3.5.2(2): Change of device No. in Description of Electromagnetic brake
interlock
Change of device No. in Description of Remote station
communication ready
Chapter 4: WARNING: Change of sentence
Section 4.6.2(2): Note addition in diagram
Section 4.6.2(3): Note addition in diagram
Section 4.9(3)(a): Change of diagram, Note addition in diagram
Section 4.9(3)(b) to (e): Note addition in diagram
Section 5.2.3(1) to (3): Addition of RY(n+2)0 and RY(n+2)1 in timing chart and
Note addition
Section 5.4.2 to 5.4.5: Addition of line in table (Remote register-based
position/speed specifying system (only when 2 stations
are occupied))
Section 5.4.7 to 5.6.9: Addition of line in table (Remote register-based
position/speed specifying system (only when 2 stations
are occupied))
Section 5.5: POINT addition
Section 5.5(5): WARNING: Change of sentence
Sep., 2007 SH(NA)030036-F Chapter 11: WARNING: Change of sentence
Section 12.4.2: AL.20 Cause addition
Section 12.4.2: Change of sentence in AL.32. Definition
Section 12.4.2: Addition of Cause 8, 9 for AL.33
Section 12.4.2: Change of sentence in AL51. Definition
Section 13.3: Change of 3M connector to RoHS compatible product
Section 14.2: Addition of servo motor
Chapter 15: WARNING: Change of sentence
Section 15.1.2: Overall change to FR-BU2
Section 15.1.4: Change of 3M connector to RoHS compatible product
Change of DDK connector to RoHS compatible product
Section 15.2.1(3): Change of twisted cable
Section 15.2.6(1)(b): Addition of sentence
Section 15.2.6(2)(d): Change of sentence
Section 15.2.6(f): Addition
Section 15.2.8: Addition of connection diagram and surge protector
Appendix 4: Addition
General-Purpose AC Servo
J2-Super Series
CC-Link Compatible
MODEL
J2-Super Series
MR-J2S- CP-S084
SERVO AMPLIFIER
INSTRUCTION MANUAL
MR-J2S- CP-S084
Servo Amplifier Instruction Manual
MODEL
MODEL
CODE
HEAD OFFICE : TOKYO BLDG MARUNOUCHI TOKYO 100-8310

F
F
This Instruction Manual uses recycled paper.

SH (NA) 030036-F (0709) MEE Printed in Japan Specifications subject to change without notice.

Drive

Uploaded by

Copyright:

Available Formats

Drive

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Drive

Uploaded by

Copyright:

Available Formats

General-Purpose AC Servo

HEAD OFFICE : TOKYO BLDG MARUNOUCHI TOKYO 100-8310

This Instruction Manual uses recycled paper.

Indicates that incorrect handling may cause hazardous conditions,

Indicates that incorrect handling may cause hazardous conditions,

: Indicates what must be done. For example, grounding is indicated by .

2. To prevent fire, note the following

3. To prevent injury, note the follow

(1) Transportation and installation

Servo amplifier Servo motor Servo amplifier Servo motor

(5) Corrective actions

(7) General instruction

About processing of waste

FOR MAXIMUM SAFETY

PRECAUTIONS FOR CHOOSING THE PRODUCTS

(1) EMC directive

(2) Low voltage directive

(3) Machine directive

2. PRECAUTIONS FOR COMPLIANCE

Servo amplifier series :MR-J2S-10CP-S084 to MR-J2S-700CP-S084

(7) Auxiliary equipment and options

(8) Performing EMC tests

(5) Options and auxiliary equipment

(6) Attachment of a servo motor

(7) About wiring protection

1. FUNCTIONS AND CONFIGURATION 1- 1 to 1-28

2.1 Environmental conditions....................................................................................................................... 2- 1

3. CC-Link COMMUNICATION FUNCTIONS 3- 1 to 3-56

3.1 Communication specifications................................................................................................................ 3- 1

4. SIGNALS AND WIRING 4- 1 to 4-36

4.1 Standard connection example ................................................................................................................ 4- 2

5.1 When switching power on for the first time.......................................................................................... 5- 1

6.1 Parameter list .......................................................................................................................................... 6- 1

7. MR Configurator (SERVO CONFIGURATION SOFTWARE) 7- 1 to 7-20

7.1 Specifications ........................................................................................................................................... 7- 1

8.1 Display flowchart..................................................................................................................................... 8- 1

9. GENERAL GAIN ADJUSTMENT 9- 1 to 9-12

9.1 Different adjustment methods ............................................................................................................... 9- 1

10.1 Function block diagram ...................................................................................................................... 10- 1

11. INSPECTION 11- 1 to 11- 2

12. TROUBLESHOOTING 12- 1 to 12-14

12.1 Trouble at start-up .............................................................................................................................. 12- 1

13. OUTLINE DIMENSION DRAWINGS 13- 1 to 13- 8

13.1 Servo amplifiers................................................................................................................................... 13- 1

14. CHARACTERISTICS 14- 1 to 14- 8

14.1 Overload protection characteristics ................................................................................................... 14- 1

15. OPTIONS AND AUXILIARY EQUIPMENT 15- 1 to 15-44

15.1 Options.................................................................................................................................................. 15- 1

APPENDIX App- 1 to App- 4

App 1. Status indication block diagram ................................................................................................. App- 1

1. FUNCTIONS AND CONFIGURATION

1.1.1 Features of CC-Link communication functions

(1) Fast communication

(2) Variable communication speed/distance system

(3) System fault prevention (station separating function)

(4) Factory Automation compatible

1.1.2 Function block diagram

The function block diagram of this servo is shown below.

Servo amplifier P C D Servo motor