Manual Piso Elevado

Tate Product Guide-13v2:Tate Product Guide.
qxd 3/25/14 11:10 AM Page 1
Access Floor Solutions

Product Guide
SustainAbility
to the Power of
Tate Product Guide-13v2:Tate Product Guide.qxd 3/25/14 11:10 AM Page 2
Developer/Built-to-Suit: KDC Development,

AAA Customer Contact Center, Oklahoma City, OK, 150,000 ft 2
High Performance and Sustainable: Great River Energy,

Maple Grove, MN, 166,000 ft 2, LEED Platinum
Tate Access Floors & SustainAbility

Social and environmental responsibility have long been key
corporate objectives within Tate. Through continuous
improvements and focus our Ability to Sustain our environment,
customers, community and company is stronger today than it
has ever been.
Environment: Over the years Tate has taken many
initiatives to reduce the environmental impact of our
manufacturing process from reducing energy usage
through automation, utilizing 100% wind power, significantly
reducing VOCs from the paint line and implementing a 100%
grey water recycling system that saves 4 million gallons annually.
Our quest for continual improvement has recently lead us to ISO
14001:2004, ISO 9001:2008 & OHSAS 18001:2007
certifications and membership in the EPAs Green Power
Partnership to support sustainable technologies.
Developer/Multi-Tenant: Buchanan Partners,

Bowie Corporate Center, Bowie, MD, 125,000 ft 2, LEED Gold
Data Center: Montana State Fund, Helena, MN, 2,000 ft 2
Customers: Tate is committed to providing the best
Community: As an advocate of green
quality access floors in the world by requiring
construction we support both our business and

local community through participations in key
stringent product performance and consistency

criteria from both its manufacturing operations and partners.
organizations, ethical procurement and supply chain
With the continued addition of sustainable technology and
management and social responsibility.
capacity in our fully owned manufacturing facilities, coupled with
Company: Tate is ensuring the sustainability of our
international manufacturing agreements we ensure our ability to
company through our graduate recruitment and
respond to our customers needs quickly and efficiently delivering
mentoring program and by giving each employee
on-time shipments at a rate needed to support any size installation.
adequate training in sustainability issues. Being sure that
Access flooring and underfloor service distribution offer a more
everyone from key suppliers to installation contractors are fully
sustainable solution for the design and construction of
involved in helping maintain the SustainAbility of Tate.
commercial buildings. The distribution of HVAC, electrical power,
To learn more about Tates SustainAbility visit us online at

www.tateinc.com/sustainability.aspx
voice and data cabling and other utilities underneath an

accessible modular floor offers enhanced energy-efficiency, lifecycle material savings, configuration flexibility and sustainability.
3
Technical Resources:
Design & Resource Support
Tate offers a variety of avenues to access our unsurpassed
technical assistance and support from design through construction
completion. Draw upon our unmatched breadth of experience
using one or more of our valuable resources.
Tate Technical Hotline

Dial 800.231.7788 or e-mail tateinfo@tateinc.com to consult directly with our engineers
for design and construction support or assistance with seismic calculations.
Design & Specification Guide

A comprehensive resource for architects and specifiers complete with full
product details, architectural drawings and specifications in CSI format.
On-Site & On-Line Education

AIA, USGBC, IFMA and IDCEC continuing education credits are available
through on-site underfloor service distribution presentations by Tate professionals,
or by visiting www.tateinc.com/resources/online_education.aspx.
Plenum Integrity Guides

Trade specific guides for properly designing, sealing, inspecting and
commissioning underfloor air distribution systems are available for the
architect, general contractor, and commissioning agent.
Interactive Cost Models

Use this tool to create customized cost comparisons of conventional
overhead service distribution versus access floor and underfloor services.
Contact us for a demonstration.
Dealer Network
Tates worldwide team of dealers will assist you with your
building needs. Find a dealer in your area by clicking on contacts
at www.tateinc.com.
High Performance & Sustainable Building

As a member of the USGBCl, Tate participates in supporting the goals of
creating a healthy environment. Contact a Tate LEED Accredited professional
to find out how underfloor service distribution has helped over 185 projects
achieve LEED certification or visit our website at www.tateinc.com/tate_leed.aspx
Comprehensive Website
Find everything you need from detailed product information,
technical support documentation and specifications to industry links,
project case studies and more at www.tateinc.com.
Visit www.tateinc.com or call the Technical Services Team at 800.231.7788.
Access Floor Products
ConCore Panels ..........................page

All Steel Panels ...........................page
Steel System Understructure.......page
Woodcore System.......................page
Aluminum System .......................page
Finishes .......................................page
7
8
9
10
12
14
Important Load Criteria and Key Features

CISCA Recommended Test Procedures for Raised Floors is the
system Tate conducts CISCA Concentrated load tests with
most widely accepted test methodology for raised floors in the
panels installed on thier actual understructure. This test is called
United States. This document provides a standard methodology
Design or Working Load defined as:
for all manufacturers to use when testing their products to
Design Load1 is the safe working load that can be applied to
determine the performance. When a raised floor system is
the system using a one sq.in. indentor without experiencing
specified to a performance criteria per CISCA the specification is
permanent set. This test is conducted in conformance with
stating the type of test method that must be used in order to
CISCA Concentrated Load test method but with panel tested on
evaluate if the raised floor system meets the said criteria.
actual understructure instead of steel blocks.
In addition to CISCA test methods Tate lists performance
Safety Factor is another term used by Tate to indicate that the
characteristics using test methods similar to CICSA, but are
panel supported on actual understructure system can withstand
used in international raised floor standards. We provide this
a point load of no less than (2) two times its design load rating
information to help report the load performance of an installed
without failure when tested in accordance with CISCA Ultimate
system more accurately.
Load test method. Failure is defined as the point at which the

system will no longer accept the load.
For Instance, Tate uses Design Load because CISCAs method

for Concentrated load is conducted with the panel resting on
Safety Factor2 is the multiple of the design load to the ultimate load.
ConCore System (Explanation and/or benefit)
Design Features
Panel Construction
Flat steel top sheet welded 156 times to a waffle shape bottom sheet then filled internally with lightweight cement.
Recycled Content
49% recycled content. Over 15% post-consumer.
Positive Engagement
Tates PosiLock pedestal head positions and retains panels in place without screws.
Combustibility*
Class A flame spread rating, and noncombustible compliant with ASTM E136-99.
Corner Screws
Screws do not extend below panel underneath. Screws are designed with retention feature.
Finish Options
Almost unlimited factory laminated finish options. PosiTile carpet & Integral Trim edge for HPL.
Performance
Walkability*
Quiet & solid underfoot with a sound transmission of 53 NNIC.
Safety Factor*
System provides a safety factor greater than two during static point load tests meeting all international standards.
Overload Protection
System yields gradually for built in safety.
Panel Strength Options
5 interchangeable panel strengths, meet all the requirements of a modern office building.
Cutout Strength*
System maintains design load and minimum safety factor strength when cut.
Air Leakage*
Straight, die cut panel edges yield low and predictable panel seam air leakage rates.
Plenum Divider
Attaches to pedestals maintaining underfloor access. Adjustable to meet any width requirement.
Clean Air Plenum
Painted steel panels with tight seams minimize dust and debris entering the air delivery plenum.
Industry Commitment
Tate is the oldest and largest manufacturer dedicated solely to the R&D and marketing of access flooring.
Lifting & Handling
Easy to carry with one hand and can be removed with a suction cup lifter. Panels are 25% lighter than concrete panels.
Shock Resistance
Fully encapsulated steel shell designed to resist damage when dropped.
Cracking & Reuse
Steel panels are free from unsightly cracks which improve life cycle and reuse.
Edge Design
Thin edge design eliminates adhesives from leaking between panels locking them place.
Ease of Cutting
Steel panel filled with cement cuts without special blades.
Attaching Walls
Screws and shot-pin can be driven directly into the panel without sacrificing its integrity.
Service & Usability
Key Features
Plenum
steel blocks. In order to more accurately represent an installed
*Independently certified test reports are available upon request.

1 For more information on design load visit Tates website and click on Resources / White Papers.
2 The UKs PSA MOB PF2 PS/SPU for raised access floors, the Australian Standard AS 4154-1993 for access floors and The European Standard for Access Floors EN
12825:2001 all require a min safety factor based on point load tests.
ACCESS FLOOR PRODUCTS
ConCore Panels
ConCore Access Floor panels are epoxy coated unitized
shells consisting of a flat steel top sheet welded to a formed
steel bottom sheet filled with a highly controlled mixture of
lightweight cement. Manufactured to exacting
tolerances, these non-combustible, rigid, solid
panels deliver the ultimate in strength, durability,
and acoustic performance.
Applications
With five standard load performance grades and an extensive
selection of understructure supports and floor finishes, it is
recommended that you visit our website: www.tateinc.com for
further information on product details, finish options, architectural
details, system specification, and selecting the proper panel to
meet the needs of your specific application.
Library: Champaign Public Library, Champaign, IL, 122,000 ft 2
Municipal Government: Johnson County Sunset Drive,

Olathe, KS, 136,000 ft 22, LEED Gold
ConCore Performance Selection Chart

System Performance Criteria* (Tested on Actual Understructure)
Static Loads
Rolling Loads
Understructure
System
Weight
(lbs/ft2)
Design
Loads1
(lbs)
Safety
Factors2
(min 2.0)
10
Passes
(lbs)
10,000
Passes
(lbs)
Impact
Loads
(lbs)
ConCore 1000
PosiLock
8.0 (39kg/m2)
1000 (4.4kN)
PASS
800 (3.6kN)
600 (2.7kN)
150 (68kg)
ConCore 1250
PosiLock
8.5 (42kg/m2)
1250 (5.6kN)
PASS
1125 (5.0kN)
875 (3.9kN)
150 (68kg)
ConCore 1500
PosiLock
9.0 (44kg/m )
1500 (6.7kN)
PASS
1250 (5.6kN)
1000 (4.4kN)
150 (68kg)
ConCore 1000
Bolted Stringer
9.0 (44kg/m2)
1000 (4.4kN)
PASS
800 (3.6kN)
600 (2.7kN)
150 (68kg)
ConCore 1250
Bolted Stringer
10.0 (49kg/m2)
1250 (5.6kN)
PASS
1000 (4.4kN)
800 (3.6kN)
150 (68kg)
ConCore 1500
Bolted Stringer
10.5 (51kg/m2)
1500 (6.7kN)
PASS
1250 (5.6kN)
1000 (4.4kN)
150 (68kg)
ConCore 2000
Bolted Stringer
11.5 (56kg/m2)
2000 (8.9kN)
PASS
1500 (6.7kN)
1250 (5.6kN)
150 (68kg)
ConCore 2500
Bolted Stringer
12.0 (59kg/m )
2500 (11.1kN)
PASS
2000 (8.9kN)
2000 (8.9kN)
150 (68kg)
ConCore 3000
Bolted Stringer
13.0 (63kg/m2)
3000 (13.3kN)
PASS
2700 (12.0kN) 2400 (10.7kN)
200 (91kg)
Panel
*All tests are performed using CISCAs Recommended Test Procedures for Access Floors with the exception of Design Load
1. Design Load is tested using CISCAs Concentrated Load test method on actual understructure instead of steel blocks. Design Load is
determined by taking the lesser value of ultimate load divided by two or the point at which permanent damage begins to occur (yield point).
2. Safety factor is the multiple of Design load to the Ultimate Load. International standards and Tate recommend a minimum of 2.
All Steel Panels

All Steel Access Floor panels are epoxy coated unitized
shells consisting of a flat steel top sheet welded to a
Table
formed steel bottom sheet. Manufactured to exacting
Header
tolerances, these non-combustible rigid, solid panels

deliver the ultimate in strength and durability with the
Table
Table
Header
Header
Content
Content
Content
convenience of lightweight construction.

Panel Features
The safe working load or design load for the panels are
equal to the concentrated load
Lightweight for ease of handling
Excellent grounding and electrical continuity
Applications
Full range of factory applied finishes
Completely non-combustible
Interchangeable with Concore, Perforated, and Grate panels
Available in 24" and 60cm sizes
With three standard load performance grades and complete

interchangeability with ConCore, Perforated and Grate airflow
panels, these panels coupled with an extensive selection of
understructure supports and floor finishes are suitable for a wide
range of applications from typical data/computer centers to
telecommunication rooms, mission critical facilities, electronic
assembly areas, and general purpose equipment applications.
Casino: Starlight Casino, Queensborough, BC, 100,000 ft 2
Renovation: Engberg Anderson Design Partnership,

Milwaukee, WI, 18,800 ft 2, LEED Gold
All Steel Performance Selection Chart

Static Loads
Rolling Loads
Panel
Understructure
System
Weight
(lbs/ft2)
Design
Loads1
(lbs)
Safety
Factors2
(min 2.0)
10
Passes
(lbs)
10,000
Passes
(lbs)
Impact
Loads
(lbs)
All Steel 1000
Bolted Stringer
6.0 (29kg/m2)
1000 (4.4kN)
PASS
400 (1.8kN)
400 (1.8kN)
150 (68kg)
All Steel 1250
Bolted Stringer
7.0 (34kg/m2)
1250 (5.6kN)
PASS
500 (2.2kN)
500 (2.2kN)
150 (68kg)
All Steel 1500
Bolted Stringer
8.5 (42kg/m2)
1500 (6.7kN)
PASS
600 (2.7kN)
600 (2.7kN)
150 (68kg)
Understructure Systems
for ConCore and All Steel Systems
PosiLock
Understructure Features
PosiLock design provides self-engagement and positioning of

floor panels.
Self-capturing fastener remains within the panel - will not get lost.
Steel pedestal head provides optimum strength.
Pedestal nut provides anti-vibration and locking features.
Seismic force-resistant pedestals are available that limit or

eliminate the need for special bracing.
Typical floor heights from 6"-16" (15cm-40cm).
Panel engagement
feature viewed from
underside
Low Finished Floor Height PosiLock

Available in floor heights from 27/8" to 4" (7cm-10cm).
PosiLock design provides self-engagement and positioning

of floor panels.
27/8" (7cm) finished floor height is ideal for renovation applications while
providing enough space under the floor to allow for easy cable
management.
Excellent for classroom renovations and the creation of training areas.
Easily levels uneven floors.
PosiLock pedestal for low floor

height systems
Bolted Stringer
Designed for computer rooms, data centers, industrial applications,

and heavy rolling load areas.
Allows floors to be built over 24" (60cm) high.
Panels can be gravity-held in understructure for fast removal and replacement.
Stringers provide lateral resistance to heavy rolling loads and seismic loading.
Seismic force-resistant pedestals are available that limit or eliminate the

need for special bracing.
Typical floor heights from 12"-36" (30cm-90cm).

Hot Dipped Galvanized Pedestals
Seismic Pedestals
Available with standard and fillet welded base assembly.
Steel pedestal head provides optimum strength.
Seismic force-resistant pedestals are available that limit or eliminate the

need for special bracing.
Vertical supports ranging from 16 gauge 7/8 (2.2cm) galvanized tubing

to Schedule 40 pipe.
Pedestals can accommodate finished floor heights over 36" (90cm).
Easily levels uneven floors.
Woodcore Panels
Woodcore panels consist of high density composite wood
core glued to and encased in hot dipped galvanized formed
steel sheets. These panels are ULC Listed for flame spread
and smoke development and provide excellent rigidity,
durability, and acoustic performance.
Panel Features
Mechanically attached air seal gasket available.
No added urea formaldehyde wood is available upon

request.
High strength to weight performance.
Full range of factory laminated finishes.
support systems and numerous factory laminated finishes. Fully
Finishes available with Integral Trim edge.
Interchangeable steel perforated and die cast aluminum grates
Internally grounded.
are also available.Together they meet the needs of a wide range
Applications
Woodcore panels are available with several understructure
of applications from office environments to data centers,

telecommunication, and mission critical facilities.
Owner Occupied: ABSA, Edmonton, AB, 21,500 ft 2
Government: Calgary Water Centre, Calgary, AB, 183,000 ft 2
Woodcore Performance Chart

Static Loads
Rolling Loads
Understructure
System
Weight
(lbs/ft2)
WC5000
CornerLock
6.9 (34kg/m2)
1000 (4.4kN)
PASS
1000 (4.4kN)
700 (3.1kN)
150 (68kg)
WC5000
Snap-Tite/Bolt-Tite
7.4 (36kg/m )
1000 (4.4kN)
PASS
1000 (4.4kN)
700 (3.1kN)
150 (68kg)
WC5000
Heavy Duty Stringer
7.6 (37kg/m2)
1250 (5.6kN)
PASS
1250 (5.6kN)
875 (3.9kN)
150 (68kg)
WC6000
Heavy Duty Stringer
8.3 (41kg/m )
1500 (6.7kN)
PASS
1500 (6.7kN)
1050 (4.7kN)
150 (68kg)
Panel
Design
Loads
(lbs)
Safety
Factors
(min 2.0)
10
Passes
(lbs)
10,000
Passes
(lbs)
Impact
Loads
(lbs)
10
Understructure
Snap-Tite and Bolt-Tite Stringer

understructure system used primarily for
gravity held panels with Integral Trim
edge in computer room or equipment
rooms. This system allows for quick
and easy access to the underfloor area.
Heavy Duty Stringer

The heavy duty stringer is designed for
installations requiring additional design
and rolling load capacities. Panels are
gravity-held in the understructure for
fast removal and replacement.
Cornerlock
understructure system with the air
seal gasket mechanically
attached to the panel. Used
primarily for office environments
with modular carpet tile.
Renovation: Christman Headquarters,

Lansing, MI, 20,000 ft 2
11
Aluminum Panel Floor Systems

Floating Floors by Tate
Available in two strengths - FF1250 and FF3000
Solid Panel
Die Cast aluminum panels meet class A fire rating.
Available with a wide selection of conductive and static

dissipative coverings or coatings.
Contains no ferrous materials to disrupt magnetic fields.
Panel-to-pedestal contact ensures continuous conductivity.
Excellent rolling load performance.
Lightweight for ease of handling.
Conductive gasket ensures continuous conductivity.
Floating Floors Performance Selection Chart

Static Loads
Rolling Loads (lbs)
Understructure
System
Weight
(lbs/ft2)
Design
Loads*
(lbs)
Safety
Factors*
(min 2.0)
FF 1250 Solid Panels
All
6.50 (32kg/m2)
1250 (5.6kN)
Pass
1000 (4.4kN) 1000 (4.4kN)
150 (68kg)
FF 1250 Perforated Panels
All
6.50 (32kg/m2)
1250 (5.6kN)
Pass
1000 (4.4kN) 1000 (4.4kN)
100 (45kg)
FF1250 Grates
All
7.25 (35kg/m )
1250 (5.6kN)
Pass
1000 (4.4kN) 1000 (4.4kN)
150 (68kg)
FF 3000 Solid Panels
All
7.60 (37kg/m2) 2250 (10.0kN)
Pass
2000 (8.9kN) 2000 (8.9kN)
200 (91kg)
FF 3000 Perforated Panels
All
7.40 (36kg/m2)
Pass
1500 (6.7kN) 2000 (8.9kN)
100 (45kg)
Panel
2000 (8.9kN)
10
Passes
(lbs)
10,000
Passes
(lbs)
Understructure
FF3000 Panel
Stringerless System
FF1250 Panel
Interchangeable Panels
12
Bolted Stringer System
Impact
Loads
(lbs)
Federal Government: United States Census Bureau,

Suitland, MD, 1,000,000 ft 2
Developer/Multi-Tenant: Cadillac Fairview,

RBC Centre, Toronto, ON, 1,130,000 ft 2
13
14
Higher Education: Yale University, Kroon Hall,

New Haven, CT, 58,200 ft 2 ,LEED Platinum
Exclusive Tate Finishes

Stone Tile
Terrazzo Stone Tile Features
Made of a polyester resin, calcium carbonate, glass and

marble chips.
Ground smooth, polished, sealed and routed for a beautiful

long lasting finish.
Recycled glass and resin fillers contain high recycled content.
Installs quickly saving time and maintaining accessibility.
Porcelain Tile Features
Made with PVC Edge for consistent seams that look more like
tradition grout lines.
Wide selection of colors and style from multiple manufactures.
Installs quickly saving time and maintaining accessibility.
For more info on Tates Terrazzo Stone Finish visit

www.tateinc.com/products/tate_terrazzo.aspx
PosiTile Carpet
PosiTile System Features
24" and 60cm PosiTile carpet tiles with four permanently

affixed positioning buttons are quickly positioned on access
floor panels for one-to-one fit.
No sticky adhesive on floor panels when carpet tiles are

removed.
Carpet waste is avoided when floor panels and carpet tiles

with matching cutout holes are relocated. No attic stock of
carpet required due to planned churn.
Makes workstation relocation fast and inexpensive.
PosiTile is available in a multitude of colors and patterns.
Available with state-of-the-art static control properties.
A totally sustainable, cradle to cradle carpet tile product.
For more info or to download a copy of Tates PosiTile brochure

visit www.tateinc.com/products/positile.aspx
Tate Hardwood
Engineered Hardwood System Features
Made of a 3.4mm natural wood bonded to 11mm

Albasia wood backer.
Sanded smooth and finished with an field applied eco certified

high solids oil for a long lasting durable finish.
Different shades can be accomplished with the use of a stain

and oil mix which is field applied and buffed.
Factory laminated with no trim edge for monlithic look
Square sides with top edges beveled.
The backer is made from "compressed" vertical plies of rapidly

renewable plantation Albasia.
Naturally VOC free.
Virtually free of petroleum products and carrying a long

potential use has minimized its environmental footprint.
No harsh chemicals required to clean hardwood tile.
For more info on Tates Engineered Hardwood Finish visit

www.tateinc.com/products/tate_hardwood.aspx
15
Aesthetic Options For Any Application

Finishes
The advantages of access flooring and underfloor service
distribution are beneficial to a wide range of building applications from office to educational, mission critical, casinos and beyond.
Just like the buildings themselves, the spaces within them have
varied and specific requirements, both functionally and
aesthetically. Tate offers a wide variety of factory laminated finishes
so you can implement the appropriate look, feel and durability for
any application. As with conventional flooring, the access floor
finish options are limitless.
Selection of the many floor materials and finishes available
Cork
Wood Laminate
Engineered Hardwood
Porcelain
High Pressure Laminate
Static Control Vinyl
Rubber
Luxury Vinyl
Terrazzo
Freelay Hard Surfaces
Carpet Tile
Linoleum
Finishes Online
There are many different materials, vendors and application methods
used to apply finishes on or over access flooring. Tate has
comprised an online resource of tested and approved finishes for
access floor applications. On the website you will find vendor contact
information, application renderings, and product photos to help you
select a finish for your facility.
To access the finishes section of our website please visit
www.tateinc.com/products/finishes.aspx. If you are interested in
using a material or vendor that does not appear on the list or would
like a printed finished brochure please contact the Tate Hotline at
877-999-8283 or e-mail tateinfo@tateinc.com
16
Data Center Airflow Solutions
Directional Airflow Panels ............page

Standard Airflow Panels ..............page
Manual Controls ..........................page
Automatic Controls......................page
Fan-Assisted Controls .................page
ContainAire ..............................page
KoldLok, HotLok, AisleLok ..........page
Other Airflow Mgt Solutions.........page
18
19
20
21
22
24
26
27
17
Directional Airflow Panels

Higher Cooling Capacity and Improved Energy Efficiency
NEW!
Directional Perf Panel
(with 25% open area)
DirectAire Panel
DirectAire Panels
Directional Perf Panels
Unlike other airflow panels the DirectAire and DirectAire X2
Like the DirectAire panels the Directional Perf angles the airflow
angle the airflow toward the server rack to significantly reduce
toward the server rack to significantly reduce bypass air and
bypass air and achieve a 93% Total Air Capture (TAC) rate. This
achieve a 93% Total Air Capture (TAC) rate. This means
means 93% of the air delivered through the panel is entering the
nearly twice the airflow through the panel is entering the face of
face of a standard 42U rack. DirectAire is designed for a one-to-
the rack, improving cooling capacity and energy efficiency.
one pairing with a rack while DirectAire X2 divides the airflow to
Panel Features
provide even distribution to racks on both sides of a cold aisle.

25% open area delivers 765CFM @ .1 H2O
Panel Features
Directional air flow achieves a 93% total air capture
68% Open Area provides 2,600 CFM @ .1 H2O
Cools up to 8kW per rack
Supports 20kW per rack @ .1 H2O (X2, 10kW per rack)
Available in 3 concentrated load ratings 800, 1000 and 1250
Available in 24 and 60cm panel sizes
Available with or without a slide damper
Airflow Panel System Load Performance Chart* (Tested on Actual Understructure)

Static Loads
System
Weight
(lbs/ft2)
Design
Loads1
(lbs)
Rolling Loads
Safety
Factors2
(min 2.0)
10
Passes
(lbs)
10,000
Passes
(lbs)
Impact
Loads
(lbs)
Total
Air
Capture
Panel
Understructure
DirectAire & X2
Bolted Stringer
13.0 (63kg/m2) 2500 (11.1kN)
Min. > 2.0
2000 (8.9kN)
2000 (8.9kN)
200 (91kg)
93%
DPerf 800
Bolted Stringer
9.5 (46kg/m2)
800 (3.6kN)
Min. > 2.0
150 (68kg)
93%
DPerf 1000
Bolted Stringer
10.0 (49kg/m )
1000 (4.4kN)
Min. > 2.0
150 (68kg)
93%
DPerf 1250
Bolted Stringer
10.5 (51kg/m2)
1250 (5.6kN)
Min. > 2.0
150 (68kg)
93%
determined by taking the lesser value of ultimate load divided by two or the point at which permanent damage begins to occur.
2. Safety factor is the factor of Design load that can be divided into the Ultimate Load. International standards recommend a minimum of 2.
DATA CENTER AIRFLOW

MANAGEMENT SOLUTIONS
18
Standard Airflow Panels
GrateAire Panel
Perforated Panel
GrateAire Panels
Perforated Panels
Panel Features
Panel Features
GrateAire die-cast aluminum panels are compatible with any

24 or 60cm bolted stringer systems.
Perforated steel panels are compatible with any 24 or 60cm

bolted stringer systems.
56% unobstructed open area
25% open area
Rolling load capacity equal to that of ConCore 1250 panels

(1000 lbs/800 lbs).
Design loads with safety factors of 2, not recommended for

rolling loads.
Available with top surface adjustable damper.
All panels are available with top surface adjustable damper.
Available with an unpainted textured surface or epoxy

powder coatings.
Steel perforated panels are available with High Pressure

Laminate, vinyl and rubber floor coverings.
Interchangeable with laminated ConCore, All Steel,

Woodcore and Aluminum panels in a stringered system.
Interchangeable with laminated ConCore, All Steel and

Woodcore panels in a stringered system.
Perforated aluminum panels available for use with a bolted

stringer aluminum system.
Airflow Panel System Load Performance Chart* (Tested on Actual Understructure)

Static Loads
Rolling Loads
Panel
Understructure
System
Weight
(lbs/ft2)
GrateAire
Bolted Stringer
8.0 (39kg/m2)
1000 (4.4kN)
Min. > 2.0
1000 (4.4kN)
800 (3.6kN)
100 (45kg)
50%
Perf 800
Bolted Stringer
9.5 (46kg/m )
800 (3.6kN)
Min. > 2.0
150 (68kg)
50%
Perf 1000
Bolted Stringer
10.0 (49kg/m2)
1000 (4.4kN)
Min. > 2.0
150 (68kg)
50%
Perf 1250
Bolted Stringer
10.5 (51kg/m )
1250 (5.6kN)
Min. > 2.0
150 (68kg)
50%
Design
Loads1
(lbs)
Safety
Factors2
(min 2.0)
10
Passes
(lbs)
10,000
Passes
(lbs)
Impact
Loads
(lbs)
Total
Air
Capture
1. Design Load is tested using CISCAs Concentrated Load test method on actual understructure instead of steel blocks. Design Load is determined by
taking the lesser value of ultimate load divided by two or the point at which permanent damage begins to occur.
2. Safety factor is the factor of Design load that can be divided into the Ultimate Load. International standards recommend a minimum of 2.
19
Manual Controls for Airflow Panels

Opposed Blade Damper (OBD)

Tate's opposed blade damper allows the user infinite airflow
adjustability with very little airflow resistance. Easy adjustable
through the top surface of a GrateAire or DirectAire panel for
balancing airflow to IT equipment with fixed requirements.
Key Performance Characteristics
Provides more airflow at 100% open than slide dampers
Easily adjustable from above without grate removal
Drop in design allows for easy retrofits under Tate airflow panels
Opposed Blade Damper for use with

DirectAire and GrateAire Panels
Multi-Zone Opposed Blade Damper

Tate's multi-zone opposed blade damper enables the airflow
delivery to be balanced based on the specific load in a 14U
section of the rack. The damper allows data center operators to
individually adjust airflow to three zones within the rack (top,
middle and bottom) without removing the DirectAire panel,
ensuring fast and accurate balancing to the fixed IT load.
Reduces cooling energy usage.
For use with full or partial loaded racks.
Provides the most granular airflow control available
Multi-zone Opposed Blade Damper for use

with DirectAire Panels
Easily adjustable from above without panel removal
Slide Damper
Tate's slide damper is used to manually control airflow under
a GrateAire or Perforated panel. The slide damper is
mechanically attached to the panel to provide airflow control.
Easily adjustable from above without panel removal
Mechanically attached to panel for easy underfloor access
Manual Damper for use with

GrateAire and Perf Panels
DATA CENTER AIRFLOW

20
Automatic Controls for DirectAire Panels

SmartAire - Automatic VAV

The data center is in constant flux. Load diversity between racks
and variable server loads are the norm. New demands to reduce
energy consumption in the green data center require a fine
balance to ensure proper air flow to each rack during peak,
partial load and idle IT hardware operation.
Tates SmartAire electronically controlled variable-air-volume
damper adjusts cooling to allow for variable loads within a server
rack. The damper opens and closes to adjust the amount of
airflow and ensure the proper inlet temperature is maintained on
a rack-by-rack basis.
SmartAire Automatic Variable-Air-Volume Damper

for use with DirectAire Panels
Available Control Options

- SmartAire C - client sensor network
For more information about

DirectAire, SmartAire and
PowerAire, get Tates In-floor
Cooling Solutions for Data
Centers brochure online at:
www.tateinc.com
- SmartAire S - 1 rack mounted temperature sensor

- SmartAire M - 3 rack mounted temperature sensor
- SmartAire P - pressure differential sensor
- SmartAire T - technician activated temperature sensor
Temp Display and Setpoint Interface

for SmartAire & PowerAire
0-100% Open VAV Actuating SmartAire Damper
Sensor Mounted to the Face of the

Rack for SmartAire & PowerAire
SmartAire Key Performance Characteristics

0-22kW supported IT load per DirectAire/SmartAire pair
User programmable set point
Power disruption fail safe to fully open position
6 vane damper for large open area
Zero maintenance
Damper position is infinitely variable from 0-100%
Quick and easy installation
High Precision, Quick Response Temperature Measurement
Multiple control options available
Viewable maximum temp for walkthrough check of each rack
Optional BMS interface
Available Automatic Transfer Switch offers N+1 reliability
21
Fan Assisted Controls for DirectAire Panels

PowerAire High Volume Fan Assist Module

for use with DirectAire Panels
PowerAire Quad Fan Assist Module with redundant fan

output for low finished floor heights
PowerAire
PowerAire Quad
Tates PowerAire fan assist module is designed to provide a blast
The PowerAire Quad fan assist module is equipped with 4 fans
of cooling through an individual airflow panel. The fan
connected in parallel to provide built in redundancy. This unit is
automatically turn on when conditions require additional cooling.
only 4 deep making it ideal for retrofit situations with finished
Options are available to utilize rack mounted temperature
floor heights as low as 7.5. This unit can cool up to 18kW of
sensors or an existing client sensor network to control the fan.
supported IT load per PowerAire Quad/DirectAire @ .1 H2O
Equipped with a variable speed fan drive the fan can be throttled
PowerAire Quad Key Performance Characteristics
up or down based on the heat load requirements. This powerful
Zero maintenance
solution is capable of cooling up to 25kW of IT load at .1 H2O for
Installation can be carried out by IT staff
solving the toughest hot spots in a data center.
Multiple control options available:

PowerAire Key Performance Characteristics
- PowerAire Quad C - client sensor network
Zero maintenance
- PowerAire Quad S - 1 rack mounted temperature sensor
Installation can be carried out by IT staff
- PowerAire Quad M - 3 rack mounted temperature sensors
Multiple control options available:
Available in 100-120V or 200-240V power input options
- PowerAire C - client sensor network
- PowerAire S - 1 rack mounted temperature sensor

- PowerAire M - 3 rack mounted temperature sensors
Fan speed is infinitely variable from 0-100%
Viewable Peak Temp for walkthrough check of each rack
Fan speed is infinitely variable from 0-100%

Viewable Peak Temp for walkthrough check of each rack
DATA CENTER AIRFLOW

22
Airflow Panel CFM and kW Capacity Chart

Airflow
Panel
0.02 H2O (5 Pa)
0.04 H2O (10 Pa)
0.06 H2O (15 Pa)
0.08 H2O (20 Pa)
0.10 H2O (25 Pa)
CFM (L/s) (kW/Rack) CFM (L/s) (kW/Rack) CFM (L/s) (kW/Rack) CFM (L/s) (kW/Rack) CFM (L/s) (kW/Rack)
DirectAire
w/o Damper
1151 (543)
8.5
1626 (767)
12.0
2007 (947)
14.8
2318 (1093)
17.1
2594 (1224)
19.1
w/ OBD
986 (465)
7.3
1427 (673)
10.5
1789 (844)
13.2
2056 (970)
15.2
2331 (1100)
17.2
w/ SmartAire
938 (443)
6.9
1310 (618)
9.7
1666 (786)
12.3
1912 (902)
14.1
2134 (1007)
15.8
w/ PowerAire
2717 (1282)
20.1
2780 (1312)
20.5
2877 (1358)
21.2
2974 (1404)
22.0
3014 (1422)
22.2
w/ PA Quad
2012 (950)
14.9
2061 (973)
15.2
2111 (996)
15.6
2158 (1018)
15.9
2199 (1038)
16.2
w/o Damper
357 (168)
2.6
496 (234)
3.7
602 (284)
4.4
689 (325)
5.1
765 (361)
5.6
w/ Slide damper
260 (123)
1.9
367 (173)
2.7
447 (211)
3.3
515 (243)
3.8
574 (271)
4.2
w/o Damper
916 (432)
3.6
1320 (623)
5.2
1608 (759)
6.4
1860 (878)
7.4
2096 (989)
8.3
w/ OBD
907 (428)
3.6
1313 (620)
5.2
1587 (749)
6.3
1841 (869)
7.3
2062 (973)
8.2
w/ Slide damper
504 (238)
2.0
712 (336)
2.8
876 (413)
3.5
1008 (476)
4.0
1128 (532)
4.5
w/o Damper
332 (152)
1.3
476 (224)
1.9
584 (275)
2.3
666 (314)
2.6
746 (352)
3.0
w/ Slide damper
237 (112)
0.9
328 (155)
1.3
402 (190)
1.6
461 (218)
1.8
515 (243)
2.0
Directional Perf
GrateAire
Standard Perf
*Cooling capacity per rack are calculated based on the following formula (CFM x TAC) / 126 (CFM needed to cool 1kW @ 25T)
Data Center Syracuse University,

Syracuse, NY, 12,000 ft 2
23
Aisle Containment
Cold Aisle Containment
Hot Aisle Containment
A cold aisle containment system can be created using
A hot aisle containment system will need to use the ContainAire
ContainAire partitions or a retracting roof. A retracting roof keeps
partitions around the top of the racks since the hot air will need
the cool air closer to the equipment however, Partitions can be
to exhaust through the ceiling return grilles. These systems can
used when solid ceiling tiles are in place over the aisle.
be used with any door option.
ContainAire Partitions
The ContainAire Vertical Partition System combines costeffectiveness and ease of installation to create the finest ceiling
mounted partition system for both hot and cold aisle containment.
Tate formulated special ceiling attachments with a 360 degree swivel
so as to easily attach to ceiling grid in any direction and at any point
along the track.
High-grade aluminum tracks are connected with splicers and then
hung with UL and FM rated fire suppression links designed so that
curtains fall away during a fire, allowing sprinklers full operation range.
ContainAire Partition (close-up of fire suppression link)
ContainAire Retracting Roof
ContainAire Retracting Roof

The Tate ContainAire retracting roof system is a UL material solution
Features
for both cold and hot aisle containment. It combines cost-
Modular design (all parts snap together)
effectiveness, ease of installation, fire safety, and clean aesthetics.
2-6 foot wide models (60cm-180cm)
High-grade aluminum track, UL rated drop in panels make for a
Unlimited lengths
below sprinkler containment solution. The ContainAire retracting roof
UL/FM rated ceiling panels
kit includes all of the components and fasteners required to
Flat roof to prevent overhead obstructions
assemble and install the roof containment. Tate roofs can be
No tools required for installation
installed on the top of the rack cabinets.
DATA CENTER AIRFLOW

24
ContainAire Strip Door
ContainAire Sliding Door
ContainAire Strip Door
ContainAire Hinged & Sliding Door
The ContainAire Strip Door system provides a cost-effective and
The Tate ContainAire Hinged & Sliding Doors are constructed on a
easy to install ceiling mounted solution for sealing the aisles of the
sturdy aluminum frame designed to be durable and long lasting.
containment system. Strip doors provide a reliable barrier that keeps
Other features include a locking door, magnetic stays and no floor
hot and cold air stream segregated while also allowing for easy
threshold, which eliminates a tripping hazard.
access to the containment aisle even when carrying servers and
Each door kit includes all of the components and fasteners required
other objects.
to assemble and install the door. The door can be installed without
The ContainAire Strip Door kit includes all of the components and
having to hang it onto the aisle end racks. Instead the door sits on
fasteners required to assemble and install the system. The
the floor with two small attachments to the top of the racks.
ContainAire Strip Door can be installed on the drop-ceiling grid or be
Features
hung onto any stationary ceiling system such as cable trays, U
No threshold design prevents tripping
channel, and or directly into a variety of ceiling materials (metal,
Custom sizes & attachments (locks, stays)
cement, etc.).
Left or right handed door
Features
Sturdy aluminum supports
Modular design (all parts snap together)
Clear see-through panel
1-6 foot (30cm-180cm) long kits (easy to ship)
Side panels attach easily without hanging from the racks
96-182 (244cm-462cm) drop down length

UL and FM rated fire suppression links
360 degree ceiling attachment
For more information get Tates

ContainAire aisle containment
systems brochure online at:
www.tateinc.com
Overlapping vinyl (prevents leaks)

No tools required for installation
25
Other Airflow Management Products

Improved Air Sealing Performance
Bypass airflow can have a significant impact on the cooling

capacity and efficiency of any data center. Part of best practice
design for raised floor data centers includes the elimination of
by-pass air. By-pass air is any air delivered into the data center
that is not consumed by the equipment and exhausted as waste
heat. Some of the easiest and most commonly used products to
reduce by-pass air include the use of containment systems,
blanking panels, angular or directional air delivery, and air sealing
grommets for all wire and cable penetrations in the floor.
KoldLok Surface Mount
KoldLok
Tate offers the full range of surface mount and flush mount
KoldLok grommets in addition to the co-branded Tate KOLDLOK
air sealing grommet. Tate KOLDLOK is a 8.75x11 (22.2cm x
27.9cm) injection molded ABS plastic grommet designed to
mount in a raised floor panel. Supplied with an optional rigid lid
capable of supporting up to 250lbs (113kg) this grommet is
Tate KoldLok w/ Optional Lid
designed to be installed at the same time as the raised floor. Tate

has identified a standard cut-out location that works with any
rack to ensure that the cutout is always in the proper location
inside the back door.
HotLok
HotLok products consisting of blanking panels and rack mounted
grommets reduce high intake air temperatures by preventing hot
exhaust air from circulating to the front of the IT cabinets. This
improves IT equipment reliability and supports cooling infrastructure
optimization.
AisleLok
AisleLok products such as under rack panels and expandable air
HotLok Snap-In Blanking Panels
sealing tape are engineered to seal a variety of openings in the aisle,

blocking bypass airflow and maximizing cooling performance.
Properly managed airflow in the aisle increases efficiency, capacity
and reliability.
AisleLok Under Rack Panel
DATA CENTER AIRFLOW

26
Other Airflow Management Products

Rack Shield
The Tate Rack Shield isolation system is designed to capture
subfloor supply and dedicate it to the IT hardware thermal load. The
Rack Shield ensures that cold supply air will not spill from rack-torack across a row or around the ends.
Made with high-grade aluminum track and fire resistant clear panels
on smooth rollers the Rack Shield can be created in several sizes
depending on the area of isolation.
CRAC Hood
Rack Shield
The CRAC Hood extension is a ceiling return duct that connects the
top of the CRAC unit directly to a ceiling return plenum greatly
increasing cooling capacity and efficiency by capturing hot exhaust
air and channeling it directly into the CRAC unit. The CRAC Hood
will eliminate hot and cold air mixture helping to maintain the proper
Delta T. It will also balance the thermal load by drawing air from one
common source.
The Tate CRAC Hood is a recommended extension for both cold
CRAC Hood
(shown with access door)
and hot aisle containment because it combines cost-effectiveness

and ease of installation. Over the long-term the CRAC Hood will also
reduce total cost of ownership by improving the efficience of the
CRAC unit. The sturdy pre-painted metal frame is also equipped
with a door system for AC units with pre-filters.
In-Floor Velocity Adjustor

The Velocity Adjustor is designed to slow subfloor air velocity so
as to increase pressure. This simple scientific solution will balance
subfloor pressure, enabling supply air to be delivered at any place in
the data center. The Velocity Adjustor installs between subfloor
stations. Careful placement is a must so as to properly affect the air
In-Floor Velocity Adjustor
stream and to ensure product longevity.

The Velocity Adjustor is made of Sandel The fire fighting fabric. This
completely non-flammable cover ensures that the Velocity Adjustor is
completely safe to use in a supply plenum and comes in three sizes
that accommodate most common subfloor height.
In-Ceiling Return Grille

Tates high volume ceiling return grille directs large volumes of hot
exhaust air into the drop ceiling plenum enabling the hot air to exit
freely minimizing mixing with the cooling air flow.
In-Ceiling Return Grille

27
Data Center AT&T, New York, NY, 25,000 ft 2
Data Center Manassas, VA, 100,000 ft 2
DATA CENTER AIRFLOW

28
Underfloor Service Distribution
Underfloor Wire & Cabling ...........page

Underfloor Air Distribution ...........page
In-Floor Chilled Beam..................page
EcoCore......................................page
Casino AirConnect.....................page
30
31
32
33
34
Underfloor Wire & Cable Management

Tates has partnered with Cii, the leading manufacturer of
Key features Modular Power & Data Management
modular power and voice data systems to provide flexible
Flexibility- with plug-and-play units, installing and reconfiguring
solution for commercial interiors. Cii offers superior quality and
the office layout is fast, easy and cost-effective.
fast, flexible service with custom application capabilities.
Capacity multiple outlet units allow high capacity multi-circuit
Ciis StationLink and PVD Servicenter are the modular answer
wiring configurations to be added for future staffing needs.
to providing multiple power and data circuits to desktops and
Customization the StationLink and PVD Servicenter can be
workstations in the office. This plug-and-play system allows you
custom engineered to accommodate any office furniture and
to add new equipment or make moves, adds and changes very
provide any power, voice or data service required.
simply and quickly. The patented connectors are UL listed and

Life Cycle Costs the mobility of these devices allow you to
approved to connect and disconnect while energized, meaning

the circuit breaker does not need to be locked and tagged-out
add, move or relocate as often as you need, without having to
to make changes. As easy as unplugging a lamp, the user can
reinvest in a new power system.
disconnect and move an entire workstation with a minimal
Safety all StationLink and PVD Servicenters are UL and CSA
amount of disruption to the rest of the office.
approved. The power connectors have a first make last

break grounding and are keyed to ensure proper connection.
Telecom
Rack
Power
Breaker
Panel
Zone
Distribution
Box
Home Run
Cable
Power
Distribution
Box
Power
Extender
Cable
Thermostat
Power
Extender
Cable
PCM
(24 volt)
PVD
Servicenter
Data
Voice
30
In-floor Active
Chilled Beams
Underfloor Air Distribution

Tate Advancements in Perimeter Heating and Cooling
Underfloor Air Distribution (UFAD) has become a popular strategy
Advantages of UFAD
for heating and cooling an office building due to the significant
Enhanced indoor environmental quality through superior IAQ,
HVAC energy savings it offers while addressing a variety of other
improved acoustics, and increased daylighting opportunities.
indoor environmental needs. These needs include maintaining

Maximize flexibility at design inception and throughout the life
high-quality clean air, improving personal comfort control,

attenuating noise, responding to organizational and technology
of the building. With UFAD you can relocate, add or remove
changes quickly and easily, and supporting the overall aesthetic
diffusers to rezone the space based on current load profiles.
value of the facility all while being cost-effective in both during
Save 20% or more on your HVAC energy costs through
construction and operation.
economizer operation, and less fan energy requirements.
Tate is committed to improving UFAD design. One of the most
Easily adapts to technological and organizational changes over
critical aspects of any Commercial HVAC system is the ability to
the buildings lifecycle at low cost.
deal with the perimeter load before it affects the occupants

Improve personal comfort control with individual volume and air
inside the building. Tates EcoCore and In-Floor Active Chilled
direction control.
Beam are two of the latest technological advancements by Tate

design to improve UFAD perimeter design.
Reduced first cost and construction time due to significant

reduction in HVAC ductwork.
Reduced operating costs and lower facility and maintenance
costs through accessible, flexible, and adaptable services.
Tate underfloor air distribution system

Ceiling design freedom due
to elimination of ductwork,
cable trays, etc.
Increased daylighting
option through reduction
in large ceiling void
6"
No mixing of indoor
air pollutants
12"
Air supplied underfloor
10% of the amount of air

pressure, reducing sound levels
31
12'6"
Harness Natures Forces
9'0"
Hot air rises
In-Floor Active Chilled Beam

With a wide product range the In-floor Active Chilled Beam offers
many benefits over other perimeter solutions commonly used in
raised floor office environments. Improved energy efficiency, the
reduction of equipment and ductwork under the floor, and the
ability to create a seamlessly integrated look along the perimeter
are just a few of the advantages.
Features & Benefits
In-floor Active Chilled Beam
Handle perimeter heating and cooling loads
for heating and cooling
Chilled water is delivered safely below the floor

Gain the full energy efficiency advantage of water heating and
cooling by conditioning at the source of the load
Ability to use water below dew point and control condensation
Easily manage shoulder season conditioning
Gain advantages of stratified airflow vs. overhead chilled beams
2-Pipe
4-Pipe
2-Pipe with Electric Heat
The 2-Pipe model is designed to have
The 4-Pipe model has the ability to
Much like the 4-Pipe model, this unit is
either hot or cold water pass through the
supply hot and chilled water to the unit
capable of both heating and cooling
unit based on building demands. Supply
without switch over. Two supply and two
without changing the water supply. Both
and return water connections are located
return water connections are located on
supply and return water connections and
on opposite ends of the chilled beam.
opposite ends of the beam. Time
an electrical connection is located on the
Thermostatically controlled the unit time
modulated air and water valves allow the
device. The perimeter demands are met
modulates the air valves and water
unit to meet demand based on a
by time modulating the air valves, water
valves to meet the perimeter demands.
thermostat located in the space.
valves, and electric heat.
Heating
Cooling
In-floor Active Chilled Beam Performance

Chart
Performance
Chart
{
{
Typical Density (TD)

High Density (HD)
Typical Density (TD)
High Density (HD)
200
400
600
800
1000
1200
1400
1600
Capacity (BTU/hr/LF)
32
1800
2000
2200
2400
For more information get

Tates In-floor Active Chilled
Beam brochure online at:
www.tateinc.com
EcoCore
Phase Change Technology for Energy Efficiency
EcoCore access floor panels are steel welded shells filled with an
unique mixture of structural cement and PCM that allows the
panel to absorb thermal energy while maintaining the high level of
integrity and quality expected from Tates raised access floors.
This is possible due to utilizing a patent pending method of
mixing microscopic spheres of encapsulated PCM into the
cement. The spheres maintain their size, shape and integrity
throughout phase transitions. This allows the panels to
seamlessly integrate into a raised floor installation providing a low
impact thermal mass to absorb energy during the day that would
otherwise affect both the energy efficiency and comfort level of
the office. The stored energy is then released again overnight as
the temperature drops below the 75 F melting point.
PCM lasts the life of the building (over 100,000 changes)
Benefits of Phase Change in a Raised Floor
Tates raised floor panels provide a safe solution for applying
phase change material in a building. By embedding the material
in cement and then fully encapsulating it in a steel welded shell,
the material is protected from the external environment
Reduce perimeter heating and cooling loads during normal

business hours
Use free or low cost cooling to handle the thermal load stored
in the panels during non-business hours
Gain advantages of a raised floor system
EcoCore Perimeter Solution

Using EcoCore in the perimeter zone of the office will help to reduce the overall peak load in the space and delay the occurrence of the peak
load to later in the day. By reducing the overall peak load the amount of cooling required to keep the space comfortable is reduced. In
addition, by delaying the peak to later in the day the load can often be handled with free economizer cooling or with reduced rate electricity.
2:00PM
Solar load warms the panels during the day.

As the panels warm the phase change
material melts absorbing energy.
8:00PM
The energy is stored in the panels to be

released during non-peak hours.
33
2:00AM
As the panels cool overnight the phase

change material solidifies.
Casino AirConnect
Creating A Healthy Gaming Environment
Tates AirConnect provides significant advantages in maintaining
air quality, flexibility and the aesthetic integrity of a Casinos
gaming environment. AirConnect uses a variable-air-volume
damper or flexible duct to tap into the pressurized plenum of an
underfloor air distribution system. The air is then delivered at or
near the floor through diffusers mounted in slot bases and other
structures built on top of the raised floor. AirConnect offers the
same flexibility and improved indoor air quality of a typical floor
mounted diffuser only the diffusers can be concealed out of sight
for a more appealing aesthetic.
Features
Easily mounts under any slot base cabinet or pit boss stand.
Can be used with any air diffuser provide by a third party
vendor or custom fabricated by the slot base manufacturer
for a seamless integrated look.
All components are quick connect for easy installation and
removal during casino layout configuration changes.
AirConnect with a concealed diffuser
AirConnects plug and play placement flexibility ensure

maximum comfort is maintained.
Delivers air near floor level to maximize acoustic performance,
energy efficiency, and help eliminate smoke in the occupied zone.
Casino: FireKeepers Casino,

Battlecreek, MI, 107,000 ft 2
34
Owner: BASF Headquarters,

Florham Park, NJ, 325,000 ft 2
35
Corporate Headquarters:
7510 Montevideo Road, Jessup, MD 20794
Tate Hotline: 1-800-231-7788
Tel: 410-799-4200 Fax: 410-799-4207
Production Facilities:
7510 Montevideo Road, Jessup, MD 20794
52 Springvale Road, Red Lion, PA 17356
Canadian Office & Production Facilities:
880 Equestrian Court, Oakville, ON L6L 6L7 Canada
Tate Hotline: 1-800-231-7788
Tel: 905+847-0138 Fax: 905+847-0141
tateinc.com
kingspan.com
International Sales & Support Office:
169 Jalan Jurong Kechil
#7-011, Sherwood
Singapore 598669
Tel: 65-6468-1332 Fax: 65-6468-6681
tateglobal.com
Tate Access Floors, Inc.

components are proudly
made in the U.S.A.
A member of
0DUNVPXVWEH
DWOHDVWWDOO
DVVKRZQKHUH
;;
FDUERQ
RIIVHW
Tate, ConCore, PosiLock, PosiTile, PVD Servicenter, Floating Floors, Integral Trim, GrateAire, DirectAire, SmartAire, PowerAire and SustainAbility are registered trademarks of
;;
Tate Access Floors, Inc. ContainAire is a trademark of Tate Access Floors, Inc. 2001 Tate Access Floors, Inc. Revised 2013
FDUERQ
RIIVHW
306RU&0<.

Manual Piso Elevado

Uploaded by

Document Informationclick to expand document informationManual Piso Elevado

Document Informationclick to expand document information

Copyright:

Available Formats

Manual Piso Elevado

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual Piso Elevado

Uploaded by

Copyright:

Available Formats

Tate Product Guide-13v2:Tate Product Guide.

qxd 3/25/14 11:10 AM Page 1

Access Floor Solutions

Tate Product Guide-13v2:Tate Product Guide.qxd 3/25/14 11:10 AM Page 2

Developer/Built-to-Suit: KDC Development,

High Performance and Sustainable: Great River Energy,

Tate Product Guide-13v2:Tate Product Guide.qxd 3/25/14 11:10 AM Page 3

Tate Access Floors & SustainAbility

Developer/Multi-Tenant: Buchanan Partners,

Data Center: Montana State Fund, Helena, MN, 2,000 ft 2

Customers: Tate is committed to providing the best

Community: As an advocate of green

quality access floors in the world by requiring

construction we support both our business and

stringent product performance and consistency

organizations, ethical procurement and supply chain

With the continued addition of sustainable technology and

management and social responsibility.

capacity in our fully owned manufacturing facilities, coupled with

Company: Tate is ensuring the sustainability of our

international manufacturing agreements we ensure our ability to

company through our graduate recruitment and

respond to our customers needs quickly and efficiently delivering

mentoring program and by giving each employee

on-time shipments at a rate needed to support any size installation.

adequate training in sustainability issues. Being sure that

Access flooring and underfloor service distribution offer a more

everyone from key suppliers to installation contractors are fully

sustainable solution for the design and construction of

involved in helping maintain the SustainAbility of Tate.

commercial buildings. The distribution of HVAC, electrical power,

To learn more about Tates SustainAbility visit us online at

voice and data cabling and other utilities underneath an

Tate Product Guide-13v2:Tate Product Guide.qxd 3/25/14 11:10 AM Page 4

Tate Technical Hotline

Design & Specification Guide

On-Site & On-Line Education

Plenum Integrity Guides

Interactive Cost Models

High Performance & Sustainable Building

Tate Product Guide-13v2:Tate Product Guide.qxd 3/25/14 11:10 AM Page 5

Access Floor Products

ConCore Panels ..........................page

Tate Product Guide-13v2:Tate Product Guide.qxd 3/25/14 11:11 AM Page 6

Important Load Criteria and Key Features

system Tate conducts CISCA Concentrated load tests with

most widely accepted test methodology for raised floors in the

panels installed on thier actual understructure. This test is called

United States. This document provides a standard methodology

Design or Working Load defined as:

for all manufacturers to use when testing their products to

Design Load1 is the safe working load that can be applied to

determine the performance. When a raised floor system is

the system using a one sq.in. indentor without experiencing

specified to a performance criteria per CISCA the specification is

permanent set. This test is conducted in conformance with

stating the type of test method that must be used in order to

CISCA Concentrated Load test method but with panel tested on