Corsair Instructionmanual

CARF-Models /WGLQIR#FDUIPRGHOVFRP
Building Instructions for CARF-Models F4U-1D Corsair

Thank you very much for purchasing our CARF-Models Corsair all composite aircraft, made
with our all composite prouction technique. The master plug of this Corsair was designed with a
3D CAD program, and then milled on our 3D capable CNC-router. Skilled craftsmen and
experienced modellers have finalized the shapes and contours as well as the details of the plane,
before the production mold was made. This high-tech marvel of production tooling is a precise,
handcrafted set of molds, which will allow us to supply precision composite parts for many years
to come.
Before you get started building and setting-up your aircraft, please make sure you have read this
instruction manual several times, and understood it. If you have any questions, please dont
hesitate to contact us. Below are the contact details:
Email:
Telephone:
Website:
ordersupport@carf-models.com
Phone your CARF Rep!!! He will be there for you.
http://www.carf-models.com
Liability Exclusion and Damages

You have acquired a kit, which can be assembled into a fully working R/C model when fitted out
with suitable accessories, as described in the instruction manual with the kit. However, as
manufacturers, we at CARF-Models are not in a position to influence the way you build and
operate your model, and we have no control over the methods you use to install, operate and
maintain the radio control system components. For this reason we are obliged to deny all liability
for loss, damage or costs which are incurred due to the incompetent or incorrect application and
operation of our products, or which are connected with such operation in any way. Unless
otherwise prescribed by binding law, the obligation of the CARF-Models company to pay
compensation is excluded, regardless of the legal argument employed. This applies to personal
injury, death, damage to buildings, loss of turnover and business, interruption of business or other
direct and indirect consequent damages. In all circumstances our total liability is limited to the
amount which you actually paid for this model.
BY OPERATING THIS MODEL YOU ASSUME FULL RESPONSIBILITY
FOR YOUR ACTIONS.
It is important to understand that CARF-Models Co., Ltd, is unable to monitor whether you follow
the instructions contained in this instruction manual regarding the construction, operation and
maintenance of the aircraft, nor whether you install and use the radio control system correctly. For
this reason we at CARF-Modelsare unable to guarantee or provide a contractual agreement with
any individual or company that the model you have made will function correctly and safely. You,
as operator of the model, must rely upon your own expertise and judgement in acquiring and
operating this model.
Instruction Manual F4U-1D Corsair
Page 2
&$5)0RGHOV/WGLQIR#FDUIPRGHOVFRP
Supplementary Safety Notes

Pre-flight checking:
Before every flying session check that all the models working systems function correctly, and be
sure to carry out a range check.
The first time you fly any new model aircraft we strongly recommend that you enlist the help of an
experienced modeller to help you check the model and offer advice while you are flying. He
should be capable of detecting potential weak points and errors.
Be certain to keep to the recommended CG position and control surface travels. If adjustments are
required, carry them out before operating the model.
Be aware of any instructions and warnings of other manufacturers, whose product(s) you use in
this particular aircraft, especially engine and radio equipment.
Please dont ignore our warnings, or those provided by these other manufacturers. They refer to
facts and processes which, if ignored, could result in permanent damage or fatal injury.
Attention !
This Scale-Aircraft is a high-end product and can create an enormous risk for both pilot and
spectators, if not handled with care, and used according to the instructions. Make sure that you
operate your Corsair according to the AMA rules, or those laws and regulations governing the
model flying in the country of use. The engine, servos and control surfaces have to be attached
properly. Please use only the recommended engines, servos, propellers, and accessories supplied
in the kit. Make sure that the Centre of Gravity is located in the recommended place. Use the
nose heavy end of the CG range for your first flights, before you start experimenting with moving
the CG back. If you find that you need to relocate your batteries or even add weight in the aircraft
to move the CG to the recommended position, please do so and dont try to save weight or hassle.
A tail heavy plane, in a first flight, can be an enormous danger for you and all spectators. Fix any
weights, and heavy items like batteries, very securely to the plane.
Make sure that the plane is secured properly when you start the engine. Have at least 2 helpers
hold your plane from the tail end, or from behind the wing tips, before you start the engine. Make
sure that all spectators are behind, or far in front, of the aircraft when running up the engine. Make
sure that you range check your R/C system thoroughly before the first flight. It is absolutely
necessary to range check your complete R/C installation first WITHOUT the engine running.
Leave the transmitter antenna retracted, and check the distance you can walk before fail-safe
occurs. Then start up the engine, run it at about half throttle and repeat this range check with the
engine running. Make sure that there is no range reduction before fail-safe occurs. Only then
make the 1st flight. If you feel that the range with engine running is less then with the engine off,
please contact the radio supplier and the engine manufacturer and DONT FLY at that time. If you
fly with 2.4 GHz technology, please follow the radio manufacturers instructions for range
checking. Always check range before a flying session!
Page 3
&$5)0RGHOV/WGLQIR#FDUIPRGHOVFRP
After starting your engine the first time, check for vibrations through the whole throttle range. The
engine should run smoothly with no unusual vibration. If you think that there are any excessive
vibrations at any engine rpms, DONT FLY at this time and check your engine, spinner and
propeller for proper balancing. Please follow the engine manufacturers run-in recommendations
and make sure that the engine is ran-in properly before you attempt the first flight.
The light- weight sandwich composite parts dont like too much vibration and they can suffer
damage. The low mass of all the parts results in a low physical inertia, so that any excess
vibrations can affect the servos and linkages. Check that the M3 bolts retaining the horizontal
stablisers on to the aluminium tube are installed and tight, and that the hinge wires for the rudder,
elevators and ailerons cannot come out. Make sure that your main and stab tubes are not damaged.
If you have the wing fold version, make sure that the wings lock smoothly in the down position
and that the wings are attached with the 4 bolts securely. Test cycle the folding sequence several
times when the engine is running and make sure that the down lock is always safe.
A special note if the Moki 215 or Moki 250 radial is used: Please make sure that no electric wire
can touch any hot component on the engine. All wires should be protected by additional spiral
tubing and should be fixed with cable ties on to the firewall. Any rubbing of wires needs to be
prevented by using rubber grommets where they are fed through the firerwall. Do not assume that
a radial engine runs without vibration. A radial engine with a single sided counter balance on the
crank shaft does have very noticable vibrations, which seem softer than the vibrations of a
single or twin cylinder gas engine, but they are just as abrasive to any rubbing components.
Check the retract system for reliable function. You should be able to cycle the gear at least 3
times, after the gear was retracted for 10 minutes. Please take the time to confirm that the air
system is not leaking. Depending on the many different possibilities for air leaks, the air system
might seem perfectly sealed when the gear is down, but when the gear is up, a leak might show.
Make sure that all screws and bolts on the landing gear have been tightened and checked. We rely
on the QC-procedures of our subcontractor Sierra Giant Scale and do NOT check the landing
gear equipment before it is sent to you. Please for your own interest check every bolt, and if
necessary, secure it with Locktite or similar. Check the safe function of the gear before you install
it permanently in the wing.
On the hydraulic system for the wing fold, please ONLY use T-Fittings which grab the tube from
the outside, such as Festo Push-In Tees. An oil spill is not only very time consuming to clean up,
it might ultimately be a high risk for the wing fold system to fail in flight.
If you carefully checked all the points above and followed our advice exactly, you will have a safe
and successful first flight - and many hours of pleasure with your CARF-Models F4U-1D Corsair.
Please check the important values at the end of this manual for control throws and Center of
Gravity!
Page 4
C$5)0RGHOV/WGLQIR#FDUIPRGHOVFRP
The Fiberglass Parts and their internal structure

A lot of engineering went into the structural integrity of the 3-part wing, especially keeping in
mind that a complex wing folding mechanism is to be used. Fuselage and tail planes are a fairly
standard design based on the many years of production experience of CARF Models. The hardware is complete and well chosen for the task. Much of it is pre-installed in the ARF version.
Page 5
CARF-Models Ltd.
info@carf-models.com
Getting Started!
It is highly recommended to assemble your Corsair following the steps in this instruction manual
closely. A lot of building steps are interacting and there are not too many choices as to what
should be done first, and what last. We recommend to follow this manual closely to avoid time
consuming and expensive mistakes.
CARF-Models offers the F4U-1D Corsair in 3 different versions. This manual starts at the very
beginning of assembling a folding wing kit version (#792000).
Assembling the plug-in wing version (#791000) doesnt make much difference, to the general
building approach, of course will be simplifying the build a lot. The whole chapter about the
folding wing hardware installation, and also the hydraulics installation and plumbing, can be
skipped.
Most of you will be curious about what amount of building the ARF version (#793000) will
require from you. The photos below show all the parts, which the factory installs for you before
the plane is packed and shipped. If you look at these photos, you will ask, what you still will have
to do? Well, its not much anymore.
ARF Corsair Building Jobs: Installing your engine, your servos, and adjusting your
linkages. For transport reasons we do not glue the rudder fin on to the fuselage, but this is a
10 minute job to do. Assemble the 3 torsion linkages and connecting them to the controls
and the servos. Installing the landing gear (actually bolting it in), glueing in the clear
canopy and painting the whole plane in the scheme you picked. Thats all. All in all, you
might need to read a few tiny parts of landing gear installation, and then the last 10-12
pages about engine and RC installation. And of course, the finish and the preflight info.
Now, is it worth the extra money to go with
the ARF version?
...it depends on you!
If you are a builder, you will enjoy the build
every bit as much as if youre more a flyer
and go for the ARF version.
All this is already

installed
in the CARF
Corsair ARF.
Page 6
CARF-Models Ltd.
1.
Main Gear and Gear Door Installation
To start with the gear installation first cut the borders of the gear cutouts along the line and clean
the edges. The cut out parts will not be needed anymore, so you can cut slightly smaller and sand to
fit. Please note the cutting line Gear doors and permanent mounting covers have to be cut from the
laminated carbon fibre part . Fit the 2 permanent covers in tightly, and make sure that around each
gear doors edges is a nice and constant gap of approx. 1 mm all around.
Cut the opening for gear

doors and permanent covers
in the center wing and also
cut the gear doors an permanent covers from the
carbon parts. See the lines
on the photos!
Now use a jig saw blade to remove the center area plywood from the gear mount. When we build
the internal structure of the Corsair wing, we have to make sure that the two gear ribs are in the
absolutely correct alignment and position, so that the wheel will fit nicely into the wing. And its
tight back there. So we square the mounts by leaving the gear mounting rails and the center wood
connected by a few tabs. It is a few minutes work to cut this part out. Be careful not to damage the
top wing skin with the jig saw blade. After the center wood is cut out and removed, youre the first
person in the world to see the wood structure beneath, so if there is need to re-glue a glue joint,
now will be the time to do so. Clean the wood edges with sand paper, where necessary.
Important: After cutting the wood please

check all glue joints which appear below.
Use epoxy glue and, if needed, some little
patches of fiberglass reinforcement.
Page 7
CARF-Models Ltd.
The Landing Gear Unit with Rotating Strut
lowest
Trial fit the landing gear unit now. You will

see that you will have to mill a notch in the
cooler intake area on the front inside corner,
so that the mounting tab of the landing gear
can be inserted. Having the gear unit in
place, you will have to mark and cut the inner
permanent cover in this area, too.
notch
The front outer corner of the gear unit is

surely going to touch the top skin of the
wing. Its very tight there, and you can mill
out the 2mm sandwich foam to gain another
2mm space. You can also grind the gear unit
a little bit to round corners, which will give
you another one or two mm. Cycle the gear
by hand to see if strut and wheel do not bind
or hit anywhere. If the mounting rails are not
100% parallel, please use very thin plywood
(included in the hardware bag) to slightly
pack the mounting areas.
Page 8
CARF-Models Ltd.
If necessary, you can pack a few

layers of 0.8 mm plywood on top of
the rails to get the landing gear unit 12 mm further up. As soon as the gear
cycles smoothly use a pen to mark the
holes to be drilled.
With the gear mounted, determine the
best wood tab positions for the little
sheet metal screws to hold the
permanent gear covers in place. You
can use scrap pieces of 3mm plywood
to make the tabs and glue them in
place with thick CA. Fit the
permanent covers with tape and drill
1.5mm holes, which will work
perfectly for the supplied 2.2mm
sheet metal screws.
Check allignment of gear to be

parallel in front and side view.
Page 9
CARF-Models Ltd.
The front gear door, which covers the strut, will

be attached when the landing gear is finally
mounted. So please disregard this step for now.
The two main doors for the wheel wells are going
to be attached next.
Create two 50 mm long hinge pins

from the 2mm steel wire, bend one end 90 deg.
Cut 2 plastic tubes per hinge, approx. 20 mm
long, and slide them on the hinge pin. Assemble
hinge pins and plastic tubes into the hinges. Trial
fit the doors with the assembled hinges into the
wheel opening. You will realize that the doors
(laminated carbon sheet) are thinner than the
sandwich material of the wing. To create the
correct hinge geometry you must remove the
sandwich foam around the white plastic tubes, so
that the gear door surface and wing skin are on
the same level.
4 mm
Determine the hinge position according to the

photos and create a slot in the wheel bay edge
approx 5 mm long and 3 mm wide at every hinge
point. Sand the inside of the gear doors
in the hinge area and tack the hinges in
place with a drop of CA. Make sure
that the position of the hinges match
the slots. Use a 2mm steel pin to align
both hinges per door. The hinge pin
must be at least 4 mm away from the
door edge (see dimension on photo) to
enable the door to open fully.
Once all fits nicely, glue the white tubes with a

drop of 5 minute epoxy into the wing. Use wide
masking tape to hold the gear door in place while
the glue is setting. After the glue has set, take off
the masking tape and check movement. Glue little
recessed tabs from 0.8mm plywood on the rear
edge and front edge of the wheel bay cutout for
the gear door to rest against when closed. The
rear resting lip should not be in the exact center
of the cutout, because it could fowl interfere the
wheel.
After everything works smoothly, you can apply
nice epoxy fillets to every glue joint, as some
joints have been only tack-glued during the
assembly process.
Page 10
CARF-Models Ltd.
Now you can install the mounting

plates for the gear door cylinders,
which are made from 3mm plywood
and are glued to the bottom of the
wheel bay. The length and the stroke
of the Robart Cylinders is perfectly
right. There is no room for an
additional clevis, but a 90 degree
bend of the 2mm pushrod, screwed
all the way into the piston rod of the
cylinder, works perfectly.
We recommend to screw the mounts
for the Robart cylinders directly on
to the plywood board and cut the
screw tip off. Then take the
assembled unit, confirm the correct
location and glue in with epoxy.
Usually you do not have to remove
the mounts anymore, you only have
to make sure that you can access the
e-clip for the pin at any time, to
remove or replace the cylinder, if
necessary one day.
Set the end positions so that the
cylinder still has about 1 mm
Note: the photos show the folding
available travel when the gear door
wing mechanism already installed.
is mechanically closed. This will
Our instruction book describes this
hold the gear door tight during
working step at a later stage.
flight. When the cylinder is fully
extended, the angle of the gear doors
should be perfectly right, too. We
designed the hinges and control
horns matching the dimensions and
stroke of these cylinders.
The result of your hard work: A giant wheel in a perfectly
snug wheel well, covered with tightly fitted gear doors.
Page 11
CARF-Models Ltd.
2.
The wing fold mechanism
We recommend to read this following step several times before you actually start working on the
wing fold installation. This is the most complicated (and most critical) building step of your
CARF Corsair assembly and you should try to understand every paragraph in full, imagine all
possible consequences of the critical work steps. This part of the build should not be rushed, you
should allow at least 3-4 building days, to allow glue joints to cure over night before you continue
step by step.
The wing fold mechanism is a CARF Models development, where we put the most emphasis on
the simplicity of the system. On purpose we did not want to rely on a locking pin or any other
additional mechanical features, which might seem safe at first glance, but create potential of
failure when you look closer. So the design of our wing fold uses the same strong mechanical
feature as most retract systems do. A hydraulic cylinder is mounted in the outer wing stud, which
is permanently mounted to the center wing mounts with an axle. No hydraulic fluid lines need to
be disconnected when taking the outer wings off for transportation and storage. The sliding lock
pin unlocks the bottom hook of the outer stud when the cylinder expands, and pushes the pin into
the opposite end of the slot in the inner mounting claws. Then the force of the cylinder pushes the
outer wing upwards. When the wing is almost vertical, the lock pin could slide back to the outer
position in the slot, causing the wing to flop back and forth in the wind when folded all the way
up. To prevent this, a keeper is mounted to the locking pin, which interlocks with a small pin in
the center wing fold mount. Incredibly simple, but very effective and safe.
The Haeusl hydraulic system itself has been used in retract systems for many years, and has
proven its reliability world wide. Jet modelers know Haeusl pumps very well, these high precision
units are used as fuel pumps by most turbine manufacturers. The hydraulics come with a separate
instruction manual, which you please read with great care before you start installing the system
into your Corsair.
Page 12
CARF-Models Ltd.
The first step is to trial fit the

assembled wing fold unit to the center
wing spar. Every spar has been drilled
and sanded to fit the wing fold claw
before the joining process of the
center wings mold halves. However,
it is quite possible that slight
adjustments need to be carried out,
such as sanding or grinding mounting
surfaces and holes, especially for
alignment purposes.
Unbolt the up-lock and remove from
the sliding pin for now. The up lock
only works properly when the
pressurized cylinder operates the
movement of the aluminum stud. If
the aluminum stud is moved by hand
during the installation and the sliding
pin is not in the upper end position of
the slot, the aluminum up-lock feature
can interfere with the pin and get
damaged. As soon as the operation is
carried out by the cylinder, forcing the
sliding pin into the end positon before
any rotating movement is initiated,
this problem will not occur anymore.
Use 6x M5 bolts and stop nuts to bolt
each unit in place. Check the
alignment in the down and up folded
position as shown on the photos.
If the alignment is slightly off,
honestly, there is not very much to do
except a lot of grinding, which in
return would weaken the spar
substantially. Slight misalignments
sometimes occur in the up folded
position, when the spar twisted
slightly during the mold joining
procedure. Our recommendation is to
accept it, as it does not have any
structural or aerodynamical effects in
flight, and it is usually not visible at
all when the wing is mounted. You
should also check the distance
between the up folded wing stud and
Unbolt this up-lock

beforemoving the
unitby hand!
allignment check
from side
distance check
from top
to center wing
edge
Page 13
CARF-Models Ltd.
the top skin of the center wing. It is very

difficult to center the spar perfectly when
joining the molds, but slight corrections can
be made by grinding the holes in both spar
and aluminum claws a little bit. As a rule of
thumb a tolerance of 3 mm (1/8") is
acceptable.
Then slide the carbon sleeves on the
aluminum studs, check that they dont have
inacceptable play and that the length would
not fowl the movement of the folding wing.
The rear edge of the carbon sleeve must
match the rear end of the aluminum stud, so
that only the 8mm steel pin is visible. The
inner edge (towards the root) must have a few
mm clearance around the aluminum claws
mounted to the center wing. Slide the outer
wing over the sleeve and confirm that the root
edge would fit reasonably close to the root
edge of the center wing. Up to 1 mm can be
adjusted when gluing the sleeve into the wing,
so this should not worry you right now. As we
want to glue the wing fold permanently to the
center wing, we want to make sure that no
serious mismatch would occur.
Photo of outer wings line-up with

center wing edges
When the alignment of the wing folds is

acceptable, you should take the claws off the
spar, degrease the claws with alcohol or
acetone, and wax the bolts thoroughly. Then
apply Aeropoxy (or UHU Endfest) to the
surfaces, holes and bolts and permanently
install everything finally. Attention: Do NOT
tighten the bolts all the way! Leave them
turn open, to allow the glue to form a
perfectly matching bead between the spar and
the aluminum part. After the glue has settled
the next day, tighten the bolts finally by
applying the torque youre used to apply when
tightening e.g. an M5 prop bolt.
Attention: The above is a mandatory, but irreversible working step. Youre in trouble now if
you did not wax the bolts or didnt trial fit and move the outer wings to the up and down lock
positions. The folding studs must move freely, without any resistance, through the whole range of
movement. If the stud is not moving freely, the mounting claws are under tension when bolted to
the spar. You also must be able to slide the locking pin all the way down in the downlock position
with two fingers. If you feel resistance here, you will risk a down lock failure later. Make sure
everything operates smoothly and freely! A folding wing is a beautiful scale feature, but it requires
technical understanding and careful attention to the mechanical design to operate safely!
Page 14
CARF-Models Ltd.
The next step is to glue the sleeves
into the outer wings. Therefore sand
the inner surface of the outer wings
and the top and bottom edge of the
sleeves with rough sand paper. Trial
fit the wing and grind inside the wing
if you need to adjust the height for
perfect alignment between outer and
center wing. You can grind away
some of the carbon, up to 1 mm is
acceptable. The amount of carbon in
the outer wing is way overbuilt and
represents a huge safety margin. As
soon as the wing can be slid on
without force, wrap 3 layers of carbon
rovings on a length of 2-3 cm around
the sleeve. Then apply laminating
resin to the rovings. Use a little bit
milled fiber to thicken the resin which
is then applied on the joint surfaces.
Slide the wings right on, adjust them
perfectly to the surface of the center
wing and hold them in place with a
full width masking tape. Support the
wing tip, if necessary, or use a long
piece of masking tape to support it
towards the center wing. Let the resin
set over night.
Add Carbon strings

HERE...
...and HERE!
Next you should create the permanent

fixture of the outer wing on the wing
fold spar. We recommend to use 2 M4
bolts per wing panel, this gives you
redundancy in regards to engine
vibrations, which can losen a bolt
eventually and youll be glad to have
a second one
While the outer wing panel is securely
taped in the down position to the
center wing, drill with dia. 3.3mm
through wing, sleeve and aluminum
wing fold. Be very careful not to
damage the cylinder rod of the wing
fold cylinder. You should use a depth
gauge (any brass tube over the drill bit
will do) or a very short drill bit to
prevent drilling too deep.
Page 15
CARF-Models Ltd.
Then use an M4 tap and tap the thread

carefully so that you can insert and
tighten the M4x8 mm bolts.
Countersink the bolt heads so that
they sit firmly on the carbon sleeve.
Next day you take the wings off,
check the glue joints inside the wing,
and apply 2 strings of carbon fibre
rovings with laminating resin along
each corner of the joint, to create a
nice fillet between sleeve and wing
skin. Also double check the glue of
the two rear ribs with resin and micro
ballon. During the waiting time for
the resin to cure, you can disassemble
the wing fold and determine the
position of the front folding hinge.
You need to use an extended pin,
made from aluminum tubes, carbon
tubes or even a long round wood
dowel, to carry over the position of
the virtual axis of rotation to the front
hinge. Trial fit the wood spar in the
wing and mark the holes to be drilled
to mount the aluminum hinge to that
spar. Bolt the aluminum hinge on to
the plywood and glue the plywood
permanently in place, leaving the
extended pin as a jig in place.
A 10 mm steel,
aluminum, carbon or wood rod
needs to be modified with a 6 mm
diameter tip, to
allign the front
hinge with the
wing fold unit,
exactly parallel
and co-axial!
Page 16
CARF-Models Ltd.
Mount the opposite aluminum hinge

with an M6 bolt and a temporary nut.
Tack it to the outer wood support to
the aluminum hinge, following the
approximate curve of the wing. Slide
the outer wing on and trial fit the
wood piece in the outer wing panel.
This works best when you have the
wings folded upright. It gives you
room to work. You might have to
shape the outer contour of the wood,
or remove and re-tack the hinge to the
wood to achieve a good result. When
the wood basically fits the outer wing,
you should pull the wing off and bolt
the aluminum hinge permanently to
the wood by using the 3.5mm sheet
metal screws, just as you did on the
center wing hinge.
Apply 30 min epoxy with some
microballon and/or milled fibre to the
wood piece which holds the outer
front aluminum hinge. Even if you do
not get the joint perfectly in one shot,
you can easily create a nice fillet to
this short plywood spar later on, after
you disassembled the front hinge by
removing the M6 bolt and temporary
nut and sliding the outer panel off, to
hold the aluminum hinge securely in
the outer wing.
You might have to adjust the cutout for the

main wing spar in the outer wing, so that
when folded all the way up, the wing skin does
not fowl the folding mech. Use the milled
cover as template, but make sure the hole is
always at least 2 mm smaller than the cover.
Ready to fill the joints with epoxy/microballon...
Note: your kit has M4 bolts and T-nuts included instead of the self tappers as in the
pics!
Page 17
CARF-Models Ltd.
Now first move the wing up and

down and finally shape the
contact edges of the center wing
with a narrow sanding block or
permagrit file so that the
movement is smooth without
any binding or locking.
Take the short piece of
aluminum tube, taper the edges
slightly and slide it into the outer
wing rear tube sleeve. Glue the
reinforcement ribs into the
center and outer wing. Glue a
little piece of the sleeve tube into
the center wing and glue an
approx. 20 mm piece of tube
into the outer wing sleeve, so
that when the wings fold down,
it slides approx. 6 mm (1/4")
into the center wing sleeve. We
have included some sleeve and
some tube for you in the
hardware bag.
The shape of this additional wood rib looks a little

different to what is included in your kit. But the
function is the same.
Congratulations: You have

managed to install the wing fold
mechanics into your Corsair
wing. This was the most
complicated task. The remaining
building steps should go very
straight forward.
Page 18
CARF-Models Ltd.
Alternatively: Plug In Wings (#791000)

Not much is to be said about the plug in
wings fit the wing tubes and slide the
wings on to the center wing. Install the 2 half
ribs in the very tip of the airfoil and glue the
front wing dowel into one side. This wing
dowel is only necessary for precise
alignment of the leading edge, it will not
have to hold a lot of flying load, as the
torsion load is carried by the two wing tubes
mainly.
As a reinforcement of the rear wing tube,
please glue in the two hard balsa supports
with epoxy resin and microballon after
cutting out the gear doors, then add another
layer of fiberglass from the front to reinforce
the rear wing tube mount in the center wing.
Check the glue joints of the ribs in the outer
wing panels and if you find any voids or
cracks, which we have overlooked, please
fill with epoxy and some microballon.
Now glue in the two root rib reinforcements
into both outer wing panels and center wing,
where the wing fixing bolt will be located.
Drill through the root ribs in this area, insert
an M6 T-nut from the inside into the outer
wing panel and trial fit the M6 wing bolt
from the inside of the wheel wells. We
recommend to screw one of the white plastic
knurled nuts on the wing bolt all the way to
the head and glue on with thin CA. This will
create a wing bolt which can be tightened by
hand, without having to use an allen hex key
when assembling the plane at the field. Now
glue in scrap balsa pieces to create a surface
where the outer wing and the center wing
butt together. This will prevent both root ribs
to be pulled together and possibly break
away from the wing skin when accidentally
overtightening the bolt. Now, losing this bolt
can have dramatic consequences, even
though the wing is mounted with a twin tube
system. It still can slide off during flight.
Make sure that the bolt is tightened properly
and check this before every flight.
Page 19
CARF-Models Ltd.
3.
Flap and aileron

attachment
Except for the very first kits, the flaps

and ailerons have all hard points
installed, where the control horns, ball
links and sliding connecting tabs are
mounted.
The most important task is that you
align ailerons and flaps when the
outer wing panels and the center wing
are joined, before you finally glue the
flap offset hinges and the aileron
hinge posts in.
The ailerons had a set of hinge posts
installed in the factory, to make sure
that the critical hinge axis is placed
correctly, also that the hinge posts can
move freely in the cutouts. Mark the
hinge post positions to the aileron
spar of the outer wing panel and mill
3 slots (3mm wide).
Do not yet glue at this point.
drawing of hinge
Page 20
CARF-Models Ltd.
Mill the slots into the flaps, outer

wing panels and center wing,
according to drawing and photos.
Make sure that you carry over the
measurements correctly.
It is very helpful to have a long
straight piece of aluminum or wood,
which can help to align the 4 flaps and
ailerons and outer flap to straight
trailing edges. Use a waterproof pen
and mark the position of flaps and
ailerons. You can use some masking
tape to protect the surface of the parts.
Some pens will not be 100%
removable from the silver paint of the
parts, after installation is completed.
Assemble the flap hinges with the

3mm thick flap-side piece and the 2
2mm thick wing-side pieces with an
M4 bolt and stop nut.
115 mm
The edges of the wing surfaces need

to be sanded from the inside, so that
the flaps can be installed deep enough
into the wing. Use a flat permagrit
plate or a rough sand paper glued to a
piece of thin plywood.
m
22 m
Photo of assembled hinge
Page 21
CARF-Models Ltd.
Dry fit the wing side of the flap offset

hinges and the hinge posts of the
ailerons all together. Once you are
sure that the alignment of the 6 flaps
and 2 ailerons is correct, glue the flapside hinges into the flaps according to
drawing and photos. Do take only a
reasonable amount of 30 min epoxy,
because too much could heat up
inside the flap and could distort the
fiberglass surface. Let the epoxy cure
well. Then dry fit the wing-side of the
flap offset hinges and the hinge posts
of the ailerons all together. Glue in the
hinge posts and front parts of the
offset hinges.
You should not use a resin too fast for
the job. It can take quite some time to
align all surfaces properly. 5 minute
epoxy is definitely NOT suited, and
30 minute epoxy can still be too fast.
Finish one wing first, and then start
with the opposite wing. Do not
attempt to glue all 8 surfaces at the
same time. Use the straight edge again
if you need to make sure that the
trailing edge is straight.
When all is glued and freely moving,
take the hinges apart and take all
controls off. Use resin filled with
microballon to create nice fillets
around the flap hinges.
Page 22
CARF-Models Ltd.
Slide every hinge

down into the slot
until the shoulder
touches the wing
surface
Center hinge of center wing top view
Inner and center hinge of center wing
Outer center wing hinge and both outer

wing hinges
cut here
Note: When you glue the flap hinges to the outer wing, (where the root hinge does not have a
wood support in the spar) please remember that the control rod will need clearance below the
20 mm tube. So you might have to cut the outer one of the front hinges short, as shown on the
photo, before you finally glue it in.
Page 23
CARF-Models Ltd.
Now determine the position of the control

horns for aileron and flaps. As all controls
are completely internal, it is very important
to get the position of the horns right.
Especially the aileron horn is only 25 mm
long, so a play free linkage, a perfect horn
and servo installation is mandatory.
Aileron: Mill an opening into the aileron at
the root and slot the spar inside the aileron,
to accept the horn. You can cut away the
front root of the aileron as well, which give
you a bit more room to work. Glue the
control horn in, as close to the top surface
as possible. Use a straight edge to extend
the top airfoil contour to the front, to get
the horn to the perfect position. Glue in the
opposite aileron horn at the same time, and
make sure that the position is identical.
This will make sure that deflections of both
ailerons will be identical as well. Use 30
min epoxy, and make sure that the glue
joint is solid and strong!!! Due to the short
arm (less than 25mm, 1" to the axis of
rotation) there will be a very high force on
the horn and the glue joint during flight. If
this joint breaks, the chances of aileron
flutter are high, which can lead to loss of
control and disintegration in flight.
Lastly, drill/mill a hole into the aileron spar
of the wing, so that the control linkage can
be installed later.
Aileron horn: Sand

surface and glue
extremely well! Your
plane lives off this
joint!
Outer Flap: The control horn, just like on

the ailerons, is installed in the very inner
edge of the flap. Therefore mill the flat
spot open and slot the balsa spar behind it.
Measure from the axis of rotation (hinge
pin hole) and write down the distance. It
should be around 40mm. You must make
sure that all 4 flap horns are installed with
that very same distance from the axis of
rotation, to allow a syncronized movement
without having to use 4 separate channels
or matchboxes for the flaps. Locate the
position of the pushrod. If necessary grind
away any excess glue you used to mount
and secure the flap offset hinge.
Page 24
CARF-Models Ltd.
Inner Flap: Drill a 3mm hole into
the root of the most inner flap at
the same distance from the axis of
rotation as the control horn is
mounted on the outer flap. This is
to mount an M3 ball link to the
root of the inner flap. As you cant
install a T-Nut from the inside, we
opted to use a short piece of
threaded rod, glued in with epoxy.
Behind the surface is a plywood
reinforcement. If you do not find a
plywood reinforcement when you
drill, just mill out the whole
surface in front of the flap spar and
insert a piece of scrap plywood.
Glue with resin.Here, however,
you indeed could use a 3mm T-Nut
from the inside, because the inside
is accessible. Mount an M3 ball
link, either with an M3 bolt, or
with an M3 secure nut on to the
threaded stud. Drill/mill an
elongated hole for the pushrod into
the spar.
Using 2 channels for the flaps, you
would use 2 y-harnesses and
combine each inner and outer flap
to one channel, and vice versa.
Inner flap: M3 bolt or all thread stud glued in.
Middle flap:
Slider glued into inner flap - middle flap slotted.
The middle flap moves by a sliding

plate interlocking into a slot. Mill a
long slot in the butting surfaces
and glue the phenolic plate into the
inner flap. Please make sure that
the angle of that plate follows the
curve of the trailing edge
somewhat, so that it will not bind
inside of the small, curved middle
flap. The slot in the middle flap
needs to be nice and tight around
the plate, so that the middle flap
does not rattle on the plate.
However, it really is enough to slot
the fiberglass surface. Any
additional reinforcement of that
slot is not necessary.
Allow flexing of flap hinges!
Page 25
CARF-Models Ltd.
If you want, you can install your servos at this point to make sure that the travel of every control
surface is sufficient and that nothing locks or binds. If necessary, you need to adjust the linkage
holes drilled in the spar and mill away some fiberglass material around the control horns.
Inner Flap Servo
Outer Flap Servo
Aileron Servo (install with an extended screwdriver)

Page 26
CARF-Models Ltd.
4.
Rear End
3 jobs have to be done at the tail end

of the plane. Firstly, the former for the
tailwheel need to be installed and the
gear door hinged. Secondly, the
elevators have to be attached to the
stab panels and the elevator torsion
linkage has to be installed, and thirdly,
the rudder, torsion linkage and fin
Assembled wooden
have to be installed. Lets start with the framework for
tailgear formers.
tailgear
Glue the interlocking wood parts of
the tailgear formers together and trial
mount the tailgear. It will be quite
difficult to mount the tail gear
cylinder when the former assembly
has already been glued in the fuselage.
Therefore it is important that you first
understand the installation method
with the slot in the wood and the
phenolic shims, to be glued to the
wood when the installation is finally
complete.
Install the complete tailgear and
cylinder temporarily into the wooden
framework before you finally glue it
into the fuselage.
Cut a slot into the fin root rib of the
fuselage according to the photos. Dry
fit the assembly into the fuselage.
When everything sits on its correct
place, glue the former assembly into
the fuselage using 30 min epoxy.
Scuff the glueing surfaces very well
and clean from dust with alcohol.
The cylinder mount is

removable until the
tailgear is finally installed, last the phenolic washer should
be glued with CA.
Page 27
CARF-Models Ltd.
Tail gear doors They are hinged in the very same way as the main gear doors. They are split in
the center, so that they can open even though the hinge line is slightly curved. They also give you
the option to install a tail hook, where all 4 doors have to be operational. If you intend not to
install a tail hook, you can glue the two rear doors in and only make the two front doors
operational. On the following pages we will describe the installation of 4 operational doors.
Tailgear Doors:
First, install the tailgear and make
sure that it retracts completely. The
tailwheel does not completely retract
into the fuselage, so you need to
create a cutout for the wheel. Keep
this cutout as tight as possible around
the wheel, it helps to center the wheel
and to support the gear doors in the
closed position later on. Then install 2
hinges to every door. See drawing and
photos for the correct hinge pin
position in relation to the doors edge.
Cut the hinge slots into the fuselage
and trial fit with a hinge pin and 2
Slot the fuselage in th hinge area like on the main gear
small white plastic tube pieces on
doors. 3 hinges for front door, 2 hinges for rear door.
each side of each hinge. You should
be able to tack all tubes to the
fuselage so that the doors move freely.
Now connect each front and rear door
with a short steel pin and 2 pieces of
plastic tube. The steel pin can be
glued into one tube, but must slide
freely in the other tube. Last but not
least, install the control horn, which
also acts as a close-lock in the
correct position and attach the springs
between the tail gear frame and the
control horns. You will have to play
with gear and doors quite a bit to find
the perfect spring tension and the best
position for the horns. These horns
also create a stop towards the fuselage Inside view of hinges with plastic tube and steel pin
skin inside the gear well. You can
reshape them, if necessary, or attach
Close-locks for front and rear door and connection pin
little plywood spacers to the inside of between both doors
the fuselage where they rest against.
Finally, disassemble the doors and fill
all tack-glue joints with 30 min epoxy
or resin and microballon to strengthen
them.
Page 28
CARF-Models Ltd.
Glue in the servo mount for the tail
gear steering right behind the wing
saddle and reinforce with some
fiberglass cloth. Install the servo and
set up the pull pull cables. We
recommend to feed them through two
sleeves (white plastic tube) in the tail
wheel former (see photo). When the
tail gear retracts these cables lengthen.
Make sure that they cannot loop
around the servo arm and lock up the
tail wheel so that it isnt able to lock
down. We recommend to use a short
piece of Tygon tubing to make the
cables stiff in the servo arm area. You
can also use springs or rubber bands
and pull them sideways to keep them
under tension. But be careful that the
rubber bands are not too strong. This
resistance can also cause the tailgear
to not lock down properly. If you want
to use a Y-lead for your tailwheel and
rudder servo, you must cross over the
tailwheel cables to get the same
direction of deflection as the rudder.
Rudder Fin:
Take the vertical fin and slot its root
surface according to the plywood spar
penetrating the fuselages fin fillet.
Slide the horizontal stab panels on to
confirm the correct angle and glue the
fin on to the fuselage. Sand the
surfaces with rough sand paper and
clean with alcohol before you glue
with 30 min epoxy. As soon as the
glue has set, mark the position of the
top hinge post by installing the rudder
temporarily. You can slide in the hinge
pin from the bottom side, but make
sure that you can grip it with a pair of
pliers later to get it out again. Mill the
top surface of the fin to accept the top
hinge post. There is only one hinge
post installed to the rudder, so make
sure that this post is mounted
properly. Glue in the plywood rib so
that the top surface of the 3mm
phenolic hinge post is flush with the
Position of tail gear

steering servo and
location for the pull/
pull wires to the tail
gear control horn.
Here you see the
springs mounted between the tail gear and
the door control horns.
Process of installing the single rudder hinge post. Take

great care because this is the only one...
Page 29
CARF-Models Ltd.
corner of the fin. When the glue has

set, drill 2 3mm holes and install the 2
M3 T-Nuts. Counter sink the holes in
the phenolic hinge post so that the
screw heads are flush with the posts
top surface. Install the rudder
temporarily to see if movement is
sufficient. You can open the slot in the
rudder slightly to allow the deflection
you desire.
Carry over the hole for the 10 mm
torsion linkage from the rudder to the
fuselage. You can drill this hole 2 mm
larger in diameter, because you will
install a ball bearing later, once the
position is perfectly determined. Take
the rudder off from the fin and glue in
the sockets/rails for the torsion linkage.
Assemble the torsion linkage from the
prepared parts, which you find in your
hardware bag, according to drawing
and photos. Dont forget to install the
ball bearing with its plywood socket to
the rod. Dry fit the linkage to the
rudders receptacle and mount
everything to the fin/fuselage. Then
you can glue the plywood bearing
socket into the fuselage. The torsion
linkage will remain in the fuselage
forever, but you still can remove the
rudder for maintenance reasons, if you
have to. The rudder servo is mounted
in the tail gear former assembly. The
push push setup of the rudder linkage
makes a second support of the torsion
linkage obsolete. You will find that the
torsion linkage becomes fully defined
and solid as soon as both pushrods are
installed between torsion rod and servo
horn.
Process of gluing the

rudder fin to the fuselage
and installing the main
fin spar.
Page 30
CARF-Models Ltd.
approx.
45 mm
Use a couple of 0.8mm ply spacers when

installing the rudder torsion linkage finally.
Servo linkages as usual...

Stab/Elevator:
First install the anti rotation pins to
the stab. Drill a 6mm hole into the
fuselages stab fairing and the stab
rootrib, wax the hole in the fuselage
fairing, stick the 6mm carbon anti
rotation pin into the fuselage and
apply 30 min epoxy on the outer part.
Then slide the stabs on the tube and
over the anti rotation pin, secure with
tape and let the epoxy set. After
sufficient time remove the stab, check
the glue joint of the anti rotation pin
and if necessary, fill the remaining
gaps with glue.
Drill 6mm, and then WAX the hole

and the surface around!
Mill the slots for the hinge posts into

the stab surfaces spar. Shorten the
inner hinge post so that it does not
interfere with the stab tube. The
elevators have to be attached to the
Page 31
CARF-Models Ltd.
stab surfaces while these are
attached to the fuselage.
Similar to the rudder, mill a
12 mm hole into the root ribs
of the stab fillet. See
dimensions on the photos on
the right. Dry fit stab with
elevators to the fuselage. Use
the elevator torsion linkage
(assembled according to the
drawing/photo) to align the
elevators properly. Then glue
the hinge posts into the stab
spar. Disassemble stabs and
elevators and fill the joints
with 30 min epoxy, where
necessary. Make sure that
these hinge posts are glued
well into the stab.
Now slide the ball bearings
with their plywood sockets on
the torsion linkage and glue
the plywood sockets into the
fuselage. Use 30 min epoxy
and sand the surfaces well
before applying glue. Mount
stab/elevator assembly while
you glue the bearing sockets
in, and make sure the
elevators move freely. After
the glue has set, drill 2 holes
through the LEFT elevator/
torsion linkage with 2.4 mm
diameter. Tap an M3 thread
into each hole, counter sink
the screw head into the
elevator from the bottom side
and mount both bolts. NOW
drill the holes for the opposite
RIGHT elevator, first
adjusting both trailing edges
exactly to the fillets on the
fuselage (you can trust the
incidence of this fillet 100%).
Next tap these holes M3,
countersink the bolt heads
and install the bolts to see the
result of your work. In case
Modify the
marked
hinge posts
to fit
38mm
Center of torsion linkage is 38 mm behind rear edge of stab tube
Use 0.8mm plywood as spacers between the edges of the counter

balance surface of the elevator,to make sure nothing locks up.
Make sure the root surface is matching the fillet with symmetrical gaps on both sides.
Insert 30 min epoxy through
the root ribs to fill the joints of
the hinge posts to the rear stab
spar. Then place it vertically
until the resin has cured. That
way it will not run off the joint.
Make sure that

the torsion
linkage stays in
during the whole
joining process.
Page 32
CARF-Models Ltd.
something went wrong
with your drilling and your
elevators are not 100
parallel, we have included
a second piece of carbon
rod for a second attempt.
Last but not least mark the
position of the stab tube
and the support rib in the
stab and drill a 3 mm hole
through stab and tube from
the bottom side. Do not
drill all the way through.
Take the stabs off and glue
an M3 T-nut into the tube
as a thread for the stab
securing bolts. You can
trim that T-nut to fit best
inside the tube. Wax a long
M3 bolt and screw it into
the nut during gluing so
that the thread stays clean
and vertical alignment is
maintained.
The result of your work is
a beautifully clean rudder
and elevator installation,
without any visible control
horns and linkages. You
are nearing the closing
stages of your building
work, left is the front end
of the plane.
The recommended
standard is
the single
servo
version,as
shown in the
pics here.
Optionally
you can use 2
elevator
servos, for
which you
have to split
the torsion
linkage.
Drill with 3 mm (mark the position carefully and precisely) and then glue in an M3 T-nut
Page 33
CARF-Models Ltd.
5.
The front end.
The cowling has 3 fixing points. Each

fixing point consists of an aluminum
tab, bolted to the fuselages firewall
with 2 M4 bolts, and a plywood tab,
glued into the cowling, holding an M4
T-nut, bolted against that aluminum
tab. The idea behind this approach is
to be able to access the mounting
bolts from the rear of the cowl
through the cooling air vents. If a
radial engine is installed, access to the
firewall from the front is very limited
due to the cylinders and the ring
muffler. Thus fixing the cowl from the
rear is very convenient. If you intend
to install a twin cylinder gas engine,
you can feel free to alter the cowl
fixture and simplify the process,
however, we recommend to use our
suggestion.
First glue on the firewall. One 3mm
plywood is glued from the inside to
the firewall (use microballon filled
epoxy to fill any gap due to the seam
band inside) and one 3mm plywood is
glued from the outside. This outside
plywood former is reinforced with a
second one, smaller in diameter,
which you need to glue on as well.
After the glue has set, tack the 3
aluminum tabs to the firewall with a
drop of thin CA glue. Use a balsa
stick along the fuselages outer
contour to determine the position of
the cowl, matching the position of the
milled plywood mount to be glued
inside the cowling.
Now tape the cowl to the fuselage. At
the top the rear surface butts against
the fuselage. At the bottom you need
to use some scrap balsa to create a jig,
which you can tack in place with a
few drops of CA. Make sure that the
top contour of the cowling is perfectly
in line with the fuselages contour,
Page 34
CARF-Models Ltd.
and the rear edge is parallel to the
firewall. After the alignment is set and
confirmed, tack the milled plywood
mounts inside the cowl, so that the
holes for the bolt match. Then you can
take the cowl off, fill the glue joints of
the plywood tabs inside the cowling
with epoxy and milled fibre, and we
recommend to add a little bit of
fiberglass cloth from the front to
reinforce the joint. Drill a 4mm hole
through the 2 inner holes of each
aluminum tab and through the firewall,
then break the aluminum tabs off.
Enlarge the holes in the firewall to
5.5mm diameter, insert M4 T-nuts from
the inside into the firewall and mount
the aluminum tabs permanently with 2
M4 bolts. Now glue a T-Nut to each
aluminum tab from the front, lining up
with the outer hole. Sand the glue
surfaces well, degrease with alcohol and
glue with a good epoxy, preferably
Hysol or UHU Endfest 300. Wax an M4
bolt and turn it into the nut to keep the
thread free of glue. Alternatively: Glue a
scrap piece of plywood from the front
against the plywood tabs in the cowl,
enlarge the holes to 5.5mm diameter
and install a T-nut the right way around.
12 mm
left
6 mm
down
Now its time to mount the engine, in

our Instruction Manual we describe the
installation of the Moki 250 5 cylinder
radial. Please be aware that the engine
diameter is not much smaller than the
cowl diameter. So, centering the engine
is crucial. First determine the center
point of the round firewall. The inner
hole is a perfect circle, central to the
outer contour. Thus it should be easy to
create the center point. A right thrust of
2.5 degree is recommended, so the
center of the engine thrust line must be
moved to the left (viewed from the front
against the firewall) by 12 mm. 0.5 deg.
upthust will be perfect. this and the
sligthly nose down cowl, makes it 6 mm
to the bottom.
Page 35
CARF-Models Ltd.
After creating the center point for your thrust line, create a template of the bolt pattern of your
engine from cardboard (including the center point) and use this template to drill your holes. It is
recommended to drill one single hole first, and then mount the engine with one bolt only. Mount
the cowl and confirm that the engine position is correct. Set the right thrust with large spacers.
Therefore you can use self tapping screws for the other mounting holes. Its not so easy with the
Moki mount, because the mounting holes are in an irregular positon, due to the 5 cylinder
locations.You might have to check both the center of prop shaft and distance of each valve rocker
to the inside of the cowl. If you find something
off, you still can move the mounting pattern of
the engine and drill the other holes, then fill the
wrongly drilled hole with a wood dowel and redrill this hole in the corrected spot.
Using M5 T-nuts the correct way from the inside
to mount your engine is not sufficient. These
will be pulled into the plywood over time and
your engine becomes lose. This can result in
fatal situations in flight. Please use large
aluminum plates or washers and glue the T-nuts
reversed on to these plates. They will distribute
the load of the bolt better to the firewalls back
side.
Now install the throttle servo and the ignition
unit inside the fuselage to the back of the
firewall. Of course there are plenty of
possibilities how and where to install both, but
please be aware that you MUST make sure that
no wire or connector can rub against the
firewall, nor touch the hot cylinders, exhaust
headers or ring exhaust. Please take great care in
perfecting your installation in this area. A small
mistake can result in the engine quitting in
flight. We have experienced this ourselves. No
cable must go through the firewall without a
rubber grommet. If you think that a radial engine
has no or very little vibration, you are very
wrong. The vibrations of a radial engine are of
different nature than the vibrations of a gas twin
cylinder engine, but they are significant and
should not be ignored. Keep cables and wires as
short as possible, fix them inside the fuselage
reliably so that they cannot lengthen or be pulled
towards the front. Test every wire that it can
under NO CIRCUMSTANCES reach a hot
engine part. Last but not least, make sure that the
ignition unit is mounted as isolated as possible,
keep batteries, receiver, servos, switches and
power leads as far away as possible.
Page 36
CARF-Models Ltd.
6.
Final wiring and

fuel/air/hydraulic
plumbing
The fuel tank installation is very

straight forward. First finish the
internal plumbing of the fuel tank as
usual and then install it to the center
board with Velcro. Fit the board into
the fuselage and glue it to the side
walls. Reinforce with fiberglass band.
On the opposite side of this center
board you can now install your
receiver, Powerbox or DPSI, if you
chose to use one. The switches can be
installed so that they are accessible
through a hatch in the fuselage,
charging sockets for receiver and
ignition battery as well. We suggest a
very practical solution with the photo
on the bottom of this page.
Aileron and flap servo extensions can
be soldered up using multi pin
connectors. Standard extension leads
of your radio manufacturer can also
be used. For the outer wing servos
you will have to permanently install
approximately 50 cm (20") long
extension wires into the center wing.
Make sure that during the wing
folding procedure the outer
connectors cannot be disconnected
accidentally. At the receivers side you
can use another short extension lead
so that you dont have to plug the
aileron/flap servo leads directly into
the receiver at every setup at the
flying field. The long extension
permanently installed in the center
wing can also incorporate a Y-harness
to the inner flap servo.
For elevator and rudder servos lead
extensions can be hard wired or
standard extensions of your radio
Page 37
CARF-Models Ltd.
manufacturer can be used. Use a Yharness to connect the tail wheel

steering servo to the rudder
(remember to cross over the pull/pull
cables to synchronise the direction of
movement).
Now prepare the wooden board to be
mounted into the center wing. Glue
the wood rails along the edges to the
bottom side of the center wing
laminate. Then use 4 sheet metal
screws to mount the board to these
wooden rails, so that it remains
removable for maintenance.
Installation of all components is also
much easier when it is removed from
the center wing.
First mount the air valves for retracts
and gear doors. In our solution we
have introduced the use of 2 JetTronic valves. Air plumbing is
straight forward, main gear and main
gear doors can be permanently
connected, the cylinder for the tail
wheel needs to be Td in with 2 quick
disconnectors. Please make sure that
all air lines are installed clean and
tidy, so that you can trouble shoot
easily if something is not working
correctly. Make sure that the color
coding is clear, the UP line should be
different in color than DOWN line.
Also keep in mind that you have
similar 3mm Festo tubing to be
installed for the wing fold. Pick the
colors carefully before you start
plumbing.
Electronically you can connect the air
valves with a Y-harness into one
receiver channel. Please put a slow
motion function to the gear channel (4
seconds UP and 1 second DOWN).
Then program the switch points
according to the valve instruction,
retract valve close to the DOWN
position, gear door valve close to the
Page 38
CARF-Models Ltd.
UP position. Therefore we suggest the

following: Set the travel of the gear
channel in your transmitter to 90 %
each way. Program the switch points
accordingly. Then increase the travel
again to 100%. That way the valves
will always switch very reliably
exactly where and when you want.
Hydraulic setup for the wing folds is
next. First install servo, valve, pump
and accumulator as suggested on the
photos. It is important that you follow
the setup and plumbing instructions of
the hydraulic system manufacturer
(Haeusl), which in case of system
updates always will overrule the
instructions given in this manual. That
there is no side load on the hydraulic
valves piston, it needs to be installed
on a rotating pin. We have included a
few milled phenolic parts, which you
can use for the valve mount.
Now, permanently install the
hydraulic lines from the cylinders to
the valve. Start on the pump side and
leave the cylinder sides long and
open. The right/left UP-lines come
together with a T-fitting (use only the
black push-in fittings) and push into
one connector at the valve block. The
DOWN lines with a T-fitting into the
other connector at the valve block.
The pump outlet is connected to the
valve where it is marked with in.
The accumulator is connected parallel
to the pump on the pressure side with
a T push-in fitting. Both feed and
return line can be Tygon. The feed
line connects the long pickup tube in
the plastic bag with the pump and the
return line connects the valves return
outlet with the plastic bag.
Schematic drawing of hydraulic plumbing
We recommend to use Baby Oil as

hydraulic medium. This is clean, nontoxic, not harmful to the skin, has no
Page 39
CARF-Models Ltd.
color, no smell and can be cleaned up after a plumbing mishap easily.

Now take a look at the cylinder side of the hydraulic lines. The cylinders in the wing fold have
3mm Festo Push-in fittings as well. The UP-side exits the cylinder at the back face.
First drill a hole into the root rib behind the top rear claw of the wing folds center wing mount.
That is the best position to feed the hydraulic lines through. Make sure it is big enough so that
both lines can slide through without resistance. When the wings move, these lines will have to
slide a few cm in and out. Connect the DOWN line straight into the cylinder and strap the UP line
to the cylinder with cable ties, so that they will not bind or interfere with the carbon sockets in the
outer wing panels. Then loop the UP line inside the aluminum frame to enter the cylinder straight
from the rear. Please slide the wings on and off several times and make sure that no tube rubs or is
squeezed or pinched inside the socket. Make sure that this is not the case in both UP and DOWN
position of the wing, as the cylinder moves up and down inside the socket during the folding cycle
quite a bit.
We recommend NOT to fill any hydraulic oil until the plane is painted. An oil spill can really
cause a lot of trouble for the paint job later. After the plane is painted and completed, a spill
mishap will not affect the strength and integrity of the wing structure. Baby Oil does lift off slowly
but surely, and it has no or only very little mechanical impact on the sandwich structure, the glue
and the plywood. It will be an unpleasant experience, but not a disaster for the plane.
Still, we will describe the filling and priming procedure at this point. Come back to this chapter
later, after the plane is painted:
Disconnect the return line from the plastic bladder. Extend this return line with a 50 cm piece of
Tygon tubing into a plastic cup placed beside or behind the center wing. Connect a piece of Tygon
tube to the return connector of the plastic bladder and fill it with baby oil. You should keep the
original container you purchased the baby oil in connected to the bladder. Or use a large syringe to
refill the plastic bladder as the pump operates the cylinders the first time. Make sure that you do
not get too much air into the plastic bladder.
We do the priming with the outer wing panels removed! Connect an air compressor and put 3-4
bar of pressure into the accumulators back side. This keeps the operating pressure low for the
first tests. Then connect the pump battery and immediately the pump should start running.
Squeeze the bladder to get liquid to the pump right away, so that it doesnt run dry. Depending on
the valve and cylinder positions, the wing fold will travel to one end position and the pump will
stop when the pressure in the system has reached the same pressure as inside the accumulator.
Now turn the servo to move the valve to the other end position, and the wing folds should move
slowly to the opposite position. You will find that oil exits the return line, which hopefully still is
feeding into the plastic cup placed on the table outside the center wing
The pump will switch on and off during the operating cycle, trying to keep the operating pressure
in the system constant. If movement is too slow, increase the pressure in the accumulator by one
or two bar. You should not need more than 4 bar, though, when the outer wing panels are not
mounted, to move the cylinders between their end positions. Cycle the wing fold several times.
Make sure that you refill the plastic bladder after every cycle. Thats why we recommend to keep a
Page 40
CARF-Models Ltd.
large syringe (or the original container) full of baby oil connected to the bladder permanently.
Watch the return line and the plastic cup, as it will fill quickly with every cycle.
When no air bubbles are visible in the return line during the cycles, connect the return line to the
bladder. Make sure the bladder is air free. It should be filled with oil approx. 25mm (1") thick.
Then cycle the system a few more times, trying to logically imagine possible air pockets in the
cylinders, moving and turning the complete center wing to try to get the air pockets placed right in
front of the cylinders tube fittings, forcing them out of the return lines during the cycles. This air
will collect in the bladder and must be released as the final step of the priming procedure. After all
air is out slide both outer wing panels on, secure them with the fixing bolts and increase operating
pressure to 6 bar. Then cycle the system again to test the speed of movement. Ideally, the pump
should operate in 1 second intervals, switching on and off during the cycle. If the pump runs
constantly during the cycle, reduce the pressure in the accumulator. If the cylinders do not safely
reach the end positions, especially in the DOWN position, increase the pressure in the
accumulator. If the pump switches on and off in 1-second intervals approximately, you have found
the correct operating pressure.
Page 41
CARF-Models Ltd.
7.
Paint and Finish
The surface of your Corsair with its silver top coat is almost ready to apply the final paint. Use a
ScotchBrite pad to roughen the surface slightly, just so that it breaks the shiny gloss. Use some
acetone or denaturized alcohol to clean the surface and remove any grease. Then tape off all
externally visible components or openings to protect the inside from any overspray. Of course,
remove engine and landing gear if you can. Do not use any primer!
Apply your scheme with any kind of 2 component polyurethane paint or base coat laquer. After
curing you should apply all trims and decals, before you finally shoot a very thin layer of flat clear
coat (or glossy, if the full scale plane youre replicating is a restored and shiny bird).
Now you can scratch the panel lines with a screw driver or steel ruler, chip color off the leading
edge areas and around rivets and hatches, if you want to create a scale patina on your plane. The
silver top coat of the fiberglass parts will shine through and look like beat up aluminum. Finally
use a pad of ScotchBrite and rub the surface in flight direction. Add a little dust of black charcoal
powder while youre doing this. The rest of patina will come by time
Cut and shape the vacuum formed radiator intake details,

paint and glue them in. Use some tape to grip and pull
them firmly from inside against the radiator inlet
After trimming and painting

the canopy frame, you need
to fit the clear canopy to the
inside, preferrably in two pieces, front and rear. Use ZAP
canopy glue or 30 min epoxy. It is very important that you
tape the canopy on to the fuselage during curing, so that it
stays in undistorted shape.
Page 42
CARF-Models Ltd.
8.
Preflight Check and First Flight
This Scale-Aircraft is a high-end product and can create an enormous risk for both pilot and
spectators, if not handled with care, and used according to the instructions. Make sure that you
operate your Corsair according to the AMA rules, or those laws and regulations governing the
model flying in the country of use. The engine, servos and control surfaces have to be attached
properly. Please use only the recommended engines, servos, propellers, and accessories supplied
in the kit. Make sure that the Centre of Gravity is located in the recommended place. Use the
nose heavy end of the CG range for your first flights, before you start experimenting with moving
the CG back. If you find that you need to relocate your batteries or even add weight in the aircraft
to move the CG to the recommended position, please do so and dont try to save weight or hassle.
A tail heavy plane, in a first flight, can be an enormous danger for you and all spectators. Fix any
weights, and heavy items like batteries, very securely to the plane.
Make sure that the plane is secured properly when you start the engine. Have at least 2 helpers
hold your plane from the tail end or from behind the wing tips, before you start the engine. Make
sure that all spectators are behind, or far in front, of the aircraft when running up the engine. Make
sure that you range check your R/C system thoroughly before the first flight. It is absolutely
necessary to range check your complete R/C installation first WITHOUT the engine running.
Leave the transmitter antenna retracted and check the distance you can walk before fail-safe
occurs. Then start up the engine, run it at about half throttle and repeat this range check with the
engine running. Make sure that there is no range reduction before fail-safe occurs. Only then
make the 1st flight. If you feel that the range with engine running is less then with the engine off,
please contact the radio supplier and the engine manufacturer and DONT FLY at this time. If you
fly with 2.4 GHz technology, please follow the radio manufacturers instructions for range
checking. Always check range before a flying session!
After starting your engine the first time, check for vibrations through the whole throttle range. The
engine should run smoothly with no unusual vibration. If you think that there are any excessive
vibrations at any engine rpms, DONT FLY at this time and check your engine, spinner and
propeller for proper balancing. Please follow the engine manufacturers run-in recommendations
and make sure that the engine is ran-in properly before you attempt the first flight.
The light- weight sandwich composite parts dont like too much vibration and they can suffer
damage. The low mass of all the parts results in a low physical inertia, so that any excess
vibrations can affect the servos and linkages. Check that the M3 bolts retaining the horizontal
stablizers on to the aluminium tube are installed and tight, and that the hinge wires for the rudder,
elevators and ailerons cannot come out. Make sure that your main and stab tubes are not damaged.
If you have the wing fold version, make sure that the wings lock smoothly in the down position
and that the wings are securely attached with the 4 bolts. Test cycle the folding sequence several
times while the engine is running and make sure that the down-lock is always safe.
A special note if the Moki 215 or Moki 250 radial is used: Please make sure that no electric wire
can touch any hot component of the engine. All wires should be protected by additional spiral
tubing and should be fixed with cable ties on to the firewall. Any rubbing of wires needs to be
prevented by using rubber grommets where they are fed through the firerwall. Do not assume that
a radial engine runs without vibration. A radial engine with a single sided counter balance on the
crank shaft does have very noticable vibrations, which seem softer than the vibrations of a
Page 43
CARF-Models Ltd.
single or twin cylinder gas engine, but they are just as abrasive to any rubbing components.
Check the retract system for reliable function. You should be able to cycle the gear at least 3
times, after the gear was retracted for 10 minutes. Please take the time to confirm that the air
system is not leaking. Depending on the many different possibilities for air leaks, the air system
might seem perfectly sealed when the gear is down, but when the gear is up, a leak might show.
Make sure that all screws and bolts on the landing gear have been tightened and checked. We rely
on the QC-procedures of our subcontractor Sierra Giant Scale and do NOT check the landing
gear equipment before it is sent to you. Please, out of your own interest, please check every bolt
and if necessary, secure it with Locktite or similar. Check the safe function of the gear before you
install it permanently in the wing.
On the hydraulic system for the wing fold, please use ONLY T-Fittings which grab the tube from
the outside, such as Festo Push-In Tees. An oil spill is not only very time consuming to clean up,
it might ultimately be a high risk for the wing fold system to fail in flight.
If you have carefully checked all the points above and followed our advice exactly, youll have a
safe and successful first flight - and many hours of pleasure with your CARF-Models Corsair.
Important Note: NEVER attempt to take off with full power, especially when you use powerful
engines like a Moki 250. The plane might nose over and this might create expensive damage.
Under full throttle you will not be able to keep the tail down using the recommended low rate
elevator settings. Always take off with 50% power only, retract the gear and then trottle up to a
comfortable speed. You must manage your throttle stick.responsibly. Your CARF-Models F4U-1D
Corsair CAN BE DESTROYED in the air if you exceed speeds of 200 km/h (125 mph)
noticably! Fly scale!
Do not take off with flaps deployed and be careful to get used to the very powerful flap authority
during landing approaches. We recommend to use a maximum flap setting of 30 deg. for a smooth
elevator control during landing approaches. This is because the huge flaps can cause weak
elevator response during slow speed. In any case, the Corsair wants to be landed tail up, that
means, with a fairly horizontally aligned fuselage. A touch down attempt on 3 wheels will most
likely end in a quite challenging situation.
Important Values:
Center of Gravity: 10-12 mm (1/2) in front of main spar, when looked from the top
Aileron Deflection: 20 mm up, 15 mm down
Elevator Deflection: 20 mm up, 20 mm down
(only for take off a higher up-rate of up to 35 mm is allowed)
Rudder Deflection: 70 mm each side
Flap Deflection: max. 45 degree, practically useful are 35 degree.
Page 44
CARF-Models Ltd.
Included Hardware
Plug-In wing version (791000)
This kit includes: hardware bag No1,
and No2, plus 4 wing tubes. Also
included are 1x fuselage bag, 1x wing
bag, 1x rudder bag and 1x elevator
bag.
Hardware bag No1 (factory-installed in ARF planes)
Wing Fold Kit Version (792000)

This kit includes hardware bag No1,
and No2, plus the complete wing fold
system. Also included are 1x fuselage
bag, 1x wing bag, 1x rudder bag and
1x elevator bag.
Wing Fold ARF Version (793000)
Hardware bag No2 (every version)
This kit includes hardware bag No2,

the hydraulic components from the
complete wing fold system, as well
as1x fuselage bag, 1x wing bag, 1x
rudder bag and 1x elevator bag.
Hardware bag No1 and the mechanical parts of the wing fold system are
already installed in the factory.
Wing fold system complete (partially installed in ARF planes)
fuselage bag
wing bag
elevator bag
rudder bag
Page 45

Corsair Instructionmanual

Uploaded by

Copyright:

Available Formats

Corsair Instructionmanual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Corsair Instructionmanual

Uploaded by

Copyright:

Available Formats

CARF-Models /WGLQIR#FDUIPRGHOVFRP

Building Instructions for CARF-Models F4U-1D Corsair

Liability Exclusion and Damages

Instruction Manual F4U-1D Corsair

Supplementary Safety Notes

Instruction Manual F4U-1D Corsair

Instruction Manual F4U-1D Corsair

The Fiberglass Parts and their internal structure

Instruction Manual F4U-1D Corsair

All this is already

Instruction Manual F4U-1D Corsair

Main Gear and Gear Door Installation

Cut the opening for gear

Important: After cutting the wood please

Instruction Manual F4U-1D Corsair

The Landing Gear Unit with Rotating Strut

Trial fit the landing gear unit now. You will

The front outer corner of the gear unit is

Instruction Manual F4U-1D Corsair

If necessary, you can pack a few

Check allignment of gear to be

Instruction Manual F4U-1D Corsair

The front gear door, which covers the strut, will

Create two 50 mm long hinge pins

Determine the hinge position according to the

Once all fits nicely, glue the white tubes with a

Now you can install the mounting

Instruction Manual F4U-1D Corsair

The wing fold mechanism

The first step is to trial fit the

Unbolt this up-lock

the top skin of the center wing. It is very

Photo of outer wings line-up with

When the alignment of the wing folds is

Add Carbon strings

Next you should create the permanent

Then use an M4 tap and tap the thread

Instruction Manual F4U-1D Corsair

Mount the opposite aluminum hinge

You might have to adjust the cutout for the

Now first move the wing up and

The shape of this additional wood rib looks a little

Congratulations: You have

Alternatively: Plug In Wings (#791000)

Flap and aileron

Except for the very first kits, the flaps

Instruction Manual F4U-1D Corsair

Mill the slots into the flaps, outer

Assemble the flap hinges with the

The edges of the wing surfaces need

Photo of assembled hinge

Instruction Manual F4U-1D Corsair

Dry fit the wing side of the flap offset

Instruction Manual F4U-1D Corsair

Slide every hinge

Inner and center hinge of center wing

Outer center wing hinge and both outer

Now determine the position of the control

Aileron horn: Sand

Outer Flap: The control horn, just like on

CARF-Models /WGLQIR#FDUIPRGHOVFRP