Edwards Signaling 302-EPM-194 Data Sheet

Edwards Signaling Catalog u Conventional Initiating
Rate Compensation
Heat Detectors
Box mount
Surface Mount
302 Series
MEA
Overview
Application
Series 302 heat detectors are designed for use in normal environments as well as environments where the detectors are subject to
weather, moisture (internal condensation), and explosive atmospheres. They are normally-open devices designed to close an
electrical circuit upon activation. All models feature rate compensation and are available with either 135 F (57.2 C) or 194 F (90
C) ratings. They are self restoring, hermetically sealed, shock and
corrosion resistant, and are tamperproof.
Sensors rated at 135 F (57.2 C) will not respond to momentary

temperature fluctuations less than 30 F/minute between 60 F
(16 C) and 100 F (38 C). Sensors rated at 194F (90 C) will not
respond to momentary temperature fluctuations less than 50 F/
minute between 60 F (16 C) and 150 F (66 C). 302 Series sensors should not be used in environments where conditions exceed
these parameters. Do not install them in hot air ducts, in front of
heaters, in paint booths that use heat to cure paint, or any other
location subject to temperature fluctuation.
Standard Features
Sensors Rated
Temperature
Minimum Ambient
Air Temperature
Maximum Ceiling
Temperature
Rate compensation offsets thermal lag
135 F (57.2 C)
194 F (90 C)
-40 F (-40 C)
-40 F (-40 C)
100 F (38 C)
150 F (66 C)
Self-restoring no manual reset required

Explosion proof and weatherproof models available
Weatherproof models available that do not require a special
backbox
The sensor's aluminum tube acts as a heat collector when sources of heat radiate directly on the tube. Install these sensors out of
direct sunlight and away from radiating heat sources including the
direct flow from heaters and heat ducts.
Box mount and surface mount models available
Page 1 of 4

S85001-0589
D ATA S H E E T
Not to be used for installation purposes. Issue 2
Typical Wiring
Rate Compensation
302 Series sensors feature rate compensation, which improves
performance by offsetting thermal lag, an inherent property of
conventional fixed temperature heat sensors.
A slow rate of temperature rise allows the heat to penetrate the
inner expansion struts. The tubular shell and the struts expand
slowly until the total device has been heated to its rated temperature level of 135 F (57.2 C) or 194 F (90 C). At this point, the
silver contact points close and an alarm is initiated.
When subjected to a rapid rate temperature rise, there is not as
much time for heat to penetrate the inner strut. However, the rapid
lengthening of the shell allows the struts to come together at a
lower level.
Black
To control
panel or
next device
End of
Line
Resistor
302 Series Detectors
White
Electrical Rating
Voltage
6-125 VAC
6-25 VDC
125 VDC
When the surrounding air temperature returns to below the rated

level, the shell contracts, forcing the contacts to open, thus automatically resetting the sensor.
Current
5 amps
1 amp
0.5 amp
Maintenance
302 Series heat sensors are low maintenance. Sensors automatically restore when temperatures drop below their rated temperatures. The accumulation of dust and dirt does not normally affect
the sensors operation.
Fine silver contact

Expansion struts
High expansion sensing
shell, 0.040 anodized aluminum
Heat control sleeve
Testing
Testing for operation is simple and can be done before or after the
sensor has been installed. Heat the sensor with a hair dryer (do
not use any device with an open flame to test sensors). The sensor should operate shortly after the hot air is applied.
Setting screw
Devcon hermetic seal
Refer to NFPA 72, National Fire Alarm Code and/or the local
authority having jurisdiction to determine testing frequency, record
keeping, and other testing considerations.
Detector Spacing
Model
UL- Vertical Spacing
(all models)
UL- Horizontal Spacing
(all models)
FM - Horizontal
or vertical spacing.*
302
50' x 50'
(15.2 x 15.2 m)
40' x 40'
(12.2 x 12.2 m)
30' x 30'
(9.1 x 9.1m)
302-AW
50' x 50'
(15.2 x 15.2 m)
40' x 40'
(12.2 x 12.2 m)
30' x 30'
(9.1 x 9.1m)
302-ET
50' x 50'
(15.2 x 15.2 m)
40' x 40'
(12.2 x 12.2 m)
30' x 30'
(9.1 x 9.1m)
302-EPM
40' x 40'
(12.2 x 12.2 m)
30' x 30'
(9.1 x 9.1m)
Not Listed
Spacing is based on smooth ceilings that are up to 10' (3 m) high. Refer to NFPA 72 for ceilings that are not considered smooth or are higher than 10' (3
m).
* EPM models are not FM approved.
Dimensions
Model
Tube Length
Tube Diameter
NPT Thread
Hex Base
Page 2 of 4

ET
3" (76.2 mm)
0.5" (12.7 mm)
0.5" (12.7 mm)
1" (25.4 mm) plastic
EMP
3" (76.2 mm)
0.5" (12.7 mm)
0.5" (12.7 mm)
1.25" (31.75 mm)
brass
WARNING Use For Property Protection Only: Heat detectors do not protect life against fire
and smoke. In most fires, hazardous levels of smoke, heat and toxic gases can build up before a
heat sensor would initiate an alarm. Independent studies indicate that heat sensors should only
be used when property protection alone is involved. In cases where life safety is a factor, the use
of smoke detectors is recommended.
Under no circumstances should heat detectors be relied upon as the sole measure to ensure fire
safety. However, if they are spaced in accordance with the specifications found under Application,
these sensors can contribute, within an overall fire safety program, to reducing the risk of avoidable property losses.
When used with automatic fire suppression systems such as pre-action and deluge sprinkler
systems, carbon dioxide systems, halon systems, and dry chemical systems, at least two sensors should be used to initiate the alarm. This is commonly referred to as cross-zoning or priority
matrix zoning and is necessary to eliminate premature discharge of the system. Refer to NFPA 72
for more information.
S85001-0589
D ATA S H E E T
Ordering Information
Interior applications
302-135
302-194
Ship Wt.
Heat Detector - Rate Compensation, Interior

Vertical Surface Mount FM & UL, 135 F (57.2
C)
Heat Detector - Rate Compensation, Interior
Vertical Surface Mount FM & UL, 194F (90
C).
0.2 lb. (0.09

kg)
For interior mounting.
Moisture & dust proof applications

302-AW-135
302-AW-194
All-weather Heat Detector - Rate

Compensation, Vertical Mounting FM & UL,
135 F (57.2 C)
Compensation, Vertical Mounting FM & UL,
194F (90 C)
Ship Wt.
Hermetically sealed for moisture proof
or dust proof installations. Requires no
special back box when the all-weather
leads are properly spliced to THW
or equivalent type wire and splices are
moisture proof. For indoor or outdoor
use.
Moisture & dust proof applications (box mount)

302-ET-135

Compensation, Vertical, Box Mount ("
NPT), FM & UL, 135 F (57.2 C). Requires
STONCO27 or equivalent.
302-ET-194

Compensation, Vertical, Box Mount ("
NPT), FM & UL, 194F (90 C). Requires
STONCO27 or equivalent.
Ship Wt.
Hermetically sealed for moisture proof
or dust proof installations. Requires no
special back box. Has plastic hexagonal
grip bushing with " conduit threads
for attachment to threaded hub cover,
or any outlet box. For indoor or outdoor
use when watertight seal is required,
use weatherproof box.
Explosion proof applications

302-EPM135
Heat Detector - Rate Compensation,

Explosionproof Mounting UL (Not FM
approved), 135 F (57.2 C). RequiresJALX-11
or equivalent
302-EPM194
Heat Detector - Rate Compensation,

Explosionproof Mounting UL (not FM
approved), 194F (90 C). RequiresJALX-11
or equivalent.
Explosion proof for installation in

hazardous locations. Has hexagonal
grip bushing with " conduit threads for
attachment to threaded hub covers of
series JL fixture fitting manufactured by
Killark Electric Co., or equivalent. Must
be hand tightened only. For indoor use
only.
Decorative white plastic adaptor plate for mounting 302 and 302-AW to any 3" outlet box
or 4" octagon outlet box.
Page 3 of 4

0.1 lb. (0.05

kg)
Ship Wt.
3 " Weatherproof, round backbox and cover (" thread hubs back, four sides and cover)
Explosion proof outlet body
JALX11
0.3 lb. (0.14

kg)
Ship Wt.
Outlet body
STONCO27
0.2 lb. (0.09

kg)
Ship Wt.
Adapter plate
AP-P
0.2 lb. (0.09

kg)
3.0 lb. (1.4 kg)
Ship Wt.
Explosion proof outlet body with cover (" thread hubs back, four sides and cover) - Killark
3.5 lb. (1.6 kg)
S85001-0589
D ATA S H E E T
Contact us...
Phone: 1-800-336-4206
Web: www.edwardssignaling.com
Edwards Signaling is
an EDWARDS brand.
3 Farm Glen Boulevard
Farmington, CT 06032
In Canada, contact Chubb Edwards...
Email: inquiries@chubbedwards.com
Web: www.chubbedwards.com
2013 UTC Fire & Security Americas
Corporation, Inc. All rights reserved.
Specifications subject to change
without notice. Edwards is part of UTC
Climate, Controls & Security, a unit of
United Technologies Corporation.
S85001-0589
D ATA S H E E T
06-27-13
Page 4 of 4

Edwards Signaling 302-EPM-194 Data Sheet

Uploaded by

Copyright:

Available Formats

Edwards Signaling 302-EPM-194 Data Sheet

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Edwards Signaling 302-EPM-194 Data Sheet

Uploaded by

Copyright:

Available Formats

Edwards Signaling Catalog u Conventional Initiating

Sensors rated at 135 F (57.2 C) will not respond to momentary

Rate compensation offsets thermal lag

Self-restoring no manual reset required

Box mount and surface mount models available

302 Series Detectors

When the surrounding air temperature returns to below the rated

Fine silver contact

Heat Detector - Rate Compensation, Interior

0.2 lb. (0.09

For interior mounting.

Moisture & dust proof applications

All-weather Heat Detector - Rate

Moisture & dust proof applications (box mount)

All-weather Heat Detector - Rate

All-weather Heat Detector - Rate

Explosion proof applications

Heat Detector - Rate Compensation,

Heat Detector - Rate Compensation,

Explosion proof for installation in

0.1 lb. (0.05

Explosion proof outlet body

0.3 lb. (0.14

0.2 lb. (0.09

0.2 lb. (0.09

3.0 lb. (1.4 kg)

3.5 lb. (1.6 kg)

You might also like