Maintenance Manual For Mitsubishi AC Servo and Spindle Controller CMDSMA1100E

Maintenance Manual
for
MDS-A, MDS-B & MDS-C1
AC Servo Amplifier & Spindle Controller
(Mitsubishi BNP-B2046C)
Publication # CMDSMA1100E
3/2001
CAUTION
This Manual is published to assist experienced personnel on the operation, maintenance

and/or programming of Mazak machine tools.
All Mazak machine tools are engineered with a number of safety devices to protect
personnel and equipment from injury or damage. Operators should not, however, rely
solely upon these safety devices, but should operate the machine only after fully
understanding what special precautions to take by reading the following documentation
thoroughly.
Do not attempt to operate or perform maintenance / repair on the machine without a
thorough understanding of the actions about to be taken. If any question exists, contact
the nearest Mazak service center for assistance.
Certain covers, doors or safety guards may be open or removed to more clearly show
machine components. These items must be in place before operating the machine.
Failure to comply with this instruction may result in serious personal injury or damage to
the machine tool.
This manual was considered complete and accurate at the time of publication, however,
due to our desire to constantly improve the quality and specification of all Mazak
products, it is subject to change or modification.
Notes:
SAFETY PRECAUTIONS
6) Do not deface, scratch or remove any caution
plate. Should it become illegible or missing,
order another caution plate from the supplier,
specifying the part number shown at the lower
right corner of the plate.
BEFORE POWERING UP
DANGER:
Cables, cords or electric wires whose insulation
is damaged can produce current leaks and
electric shocks.
Before using, check their
condition.
WARNING:
1) Be sure the instruction manual and the
programming manual are fully understood
before operating the machine. Every function
and operating procedure should be completely
clear.
2) Use approved oil resistant safety shoes, safety
goggles with side covers, safe clothes, and
other safety protection required.
3) Close all NC unit, operating panel, electric
control panel doors and covers.
CAUTION:
1) The power cable from the factory feeder switch
to the machine main circuit breaker should
have a sufficient sectional area to handle the
electric power used.
2) Cables which must be laid on the floor must be
protected from hot chips, by using rigid or
other approved conduit, so that short-circuits
will not occur.
3) Before first time operation of the machine after
unpacking it or from being idle for a long period
of time (several days or more), each sliding
part must be sufficiently lubricated. To do so,
push and release the pump button several
times until the oil seeps out on the sliding
parts. The pump button has a return spring, so
do not force it to return.
4) Oil reservoirs should be filled to indicated
levels. Check and add oil, if needed.
5) For lubrication points, oil specification and
appropriate levels, see the various instruction
plates.
6) Switches and levers should operate smoothly.
Check that they do.
7) When powering the machine on, turn on the
switches in the following order: first the factory
feeder switch, then the machine main circuit
breaker, and then the control power on switch
located on the operating panel.
8) Check the coolant level, and add coolant, if
needed.
The machine is provided with a number of safety

devices to protect personnel and equipment from
injury and damage.
Operators should not,
however, rely solely upon these safety devices,
but should operate the machine only after fully
understanding what special precautions to take by
reading the following documentation thoroughly.
BASIC OPERATING PRACTICES
DANGER:
1) Some control panels, transformers, motors,
junction boxes and other parts have high
voltage terminals. These should not be touched
or a severe electric shock may be sustained.
2) Do not touch any switches with wet hands.
This too, can produce an electric shock.
WARNING:
1) The emergency stop pushbutton switch
location should be well known, so that it can be
operated at any time without having to look for
it.
2) Before replacing a fuse, turn off the main
incoming power switch to the machine.
3) Provide sufficient working space to avoid
hazardous falls.
4) Water or oil can make floors slippery and
hazardous. All floors should be clean and dry
to prevent accidents
5) Do not operated any switch without a thorough
understanding of the actions about to be taken.
6) Avoid accidental operation of switches.
7) Work benches near the machine must be
strong enough to hold materials placed on
them to prevent accidents. Articles should be
prevented from slipping off the bench surface.
8) If a job is to be done by two or more persons,
coordinating signals should be given at each
step of the operation. The next step should not
be taken unless a signal is given and
acknowledged.
CAUTION:
1) In the event of power failure, turn off the main
circuit breaker immediately.
2) Use the recommended hydraulic oils, lubricants
and grease or acceptable equivalents.
3) Replacement fuses should have the proper
current ratings.
4) Protect the NC unit, operating panel, electric
control panel, etc. from shocks, since this
could cause a failure or malfunction.
5) Do not change parameters or electrical
settings. If changes are unavoidable, record
the values prior to the change so that they can
be returned to their original settings, if
necessary.
S-1
AFTER CONTROL POWER IS TURNED ON

CAUTION:
When the control power ON switch on the
operating panel is on, the "READY" lamp on
the operating panel should also be on (check to
see that it is).
4) Tools and other items around the machine or

equipment should be stored to ensure good
footing and clear aisles.
5) Do not place tools or any other items on the
headstock, turret, covers and similar places
(For T/M).
CAUTION:
1) Tool lengths should be within specified
tolerances to prevent interference.
2) After installing a tool, make a trial run.
ROUTINE INSPECTIONS
WARNING:
When checking belt tensions, do not get your
fingers caught between the belt and pulley.
CAUTION:
1) Check pressure gages for proper readings.
2) Check motors, gear boxes and other parts for
abnormal noises.
3) Check the motor lubrication, and sliding parts
for evidence of proper lubrication.
4) Check safety covers and safety devices for
proper operation.
5) Check belt tensions. Replace any set of belts
that have become stretched with a fresh
matching set.
OPERATION
WARNING:
1) Do not work with long hair that can be caught
by the machine. Tie it back, out of the way.
2) Do not operate switches with gloves on. This
could cause mis-operation.
3) Whenever a heavy workpiece must be moved,
if there is any risk involved, two or more people
should work together.
4) Only trained, qualified workers should operate
forklift trucks, cranes or similar equipment and
apply slings.
5) Whenever operating a forklift truck, crane or
similar equipment, special care should be taken
to prevent collisions and damage to the
surroundings.
6) Wire ropes or slings should be strong enough
to handle the loads to be lifted and should
conform to the mandatory provisions.
7) Grip workpieces securely.
8) Stop the machine before adjusting the coolant
nozzle at the tip.
9) Never touch a turning workpiece in the spindle
with bare hands, or in any other way.
10) To remove a workpiece from the machine other
than by a pallet changer, stop the tool and
provide plenty of distance between the
workpiece and the tool (for M/C).
11) While a workpiece or tool is turning, do not
wipe it off or remove chips with a cloth or by
hand. Always stop the machine first and then
use a brush and a sweeper.
12) Do not operate the machine with the chuck and
front safety covers removed (For T/M).
13) Use a brush to remove chips from the tool tip,
do not use bare hands .
14) Stop the machine whenever installing or
removing a tool.
15) Whenever machining magnesium alloy parts,
wear a protective mask.
WARM UP
CAUTION:
1) Warm up the machine, especially the spindle
and feed shaft, by running the machine for 10
to 20 minutes at about one-half or one-third the
maximum speed in the automatic operation
mode.
2) The automatic operation program should cause
each machine component to operate. At the
same time, check their operations.
3) Be particularly careful to warm up the spindle
which can turn above 4000 rpm.
If the machine is used for actual machining
immediately after being started up following a
long idle period, the sliding parts may be worn
due to the lack of oil. Also, thermal expansion
of the machine components can jeopardize
machining accuracy. To prevent this condition,
always make sure that the machine is warmed
up.
PREPARATIONS
WARNING:
1) Tooling should conform to the machine
specifications, dimensions and types.
2) Replace all seriously worn tools with new ones
to prevent injuries.
3) The work area should be adequately lighted to
facilitate safety checks.
S-2
CAUTION:
1) Thoroughly read and understand the safety
precautions in the instruction manual.
2) Thoroughly read the whole maintenance
manual and fully understand the principles,
construction and precautions involved.
MAINTENANCE OPERATION
DANGER:
1) Those not engaged in the maintenance work
should not operate the main circuit breaker or
the control power "ON" switch on the
operating panel. For this purpose, "Do not
Touch the Switch, Maintenance Operation in
Progress!" or similar warning should be
indicated on such switches and at any other
appropriate locations. Such indication should
be secured by a semi-permanent means in the
reading direction.
2) With the machine turned on, any maintenance
operation can be dangerous. In principle, the
main circuit breaker should be turned off
throughout the maintenance operation.
WARNING:
1) The electrical maintenance should be done by
a qualified person or by others competent to do
the job.
Keep close contact with the
responsible person. Do not proceed alone.
2) Overtravel limit and proximity switches and
interlock mechanisms including functional parts
should not be removed or modified.
3) When working at a height, use steps or ladders
which are maintained and controlled daily for
safety.
4) Fuses, cables, etc. made by qualified
manufacturers should be employed.
BEFORE OPERATION & MAINTENANCE BEGINS
WARNING:
1) Arrange things in order around the section to
receive the maintenance, including working
environments. Wipe water and oil off parts and
provide safe working environments.
2) All parts and waste oils should be removed by
the operator and placed far enough away from
the machine to be safe.
CAUTION:
1) The maintenance person should check that the
machine operates safely.
2) Maintenance and inspection data should be
recorded and kept for reference.
CAUTION:
1) During automatic operation, never open the
machine door. Machines equipped with the
door interlock will set the program to single
step.
2) When performing heavy-duty machining,
carefully prevent chips from being accumulated
since hot chips from certain materials can
cause a fire.
TO INTERRUPT MACHINING
WARNING:
When leaving the machine temporarily after
completing a job, turn off the power switch on
the operation panel, and also the main circuit
breaker.
COMPLETING A JOB
CAUTION:
1) Always clean the machine or equipment.
Remove and dispose of chips and clean cover
windows, etc.
2) Make sure the machine has stopped running,
before cleaning.
3) Return each machine component to its initial
condition.
4) Check the wipers for breakage.
Replace
broken wipers.
5) Check the coolant, hydraulic oils and lubricants
for contamination. Change them if they are
seriously contaminated.
6) Check the coolant, hydraulic oil and lubricant
levels. Add if necessary.
7) Clean the oil pan filter.
8) Before leaving the machine at the end of the
shift, turn off the power switch on the operating
panel, machine main circuit breaker and factory
feeder switch in that order.
SAFETY DEVICES
1) Front cover, rear cover and coolant cover.
2) Chuck barrier, tail barrier and tool barrier (NC
software).
3) Stored stroke limit (NC software).
4) Emergency stop pushbutton switch.
MAINTENANCE OPERATION PREPARATIONS
1) Do not proceed to do any maintenance
operation unless instructed to do so by the
foreman.
2) Replacement parts, consumables (packing, oil
seals, O rings, bearing, oil and grease, etc.)
Should be arranged in advance.
3) Prepare preventive maintenance and record
maintenance programs.
000X717-KY 11/98
S-3
aaaaaaaa
a
a
aaaaa
WARNING
ALWAYS TURN THE MAIN CIRCUIT BREAKER TO THE OFF POSITION & USE AN APPROVED
LOCKOUT DEVICE WHEN COMPLETING MAINTENANCE OR REPAIRS.
THE LOCKOUT PROCEDURE THAT FOLLOWS IS INTENDED TO SAFEGUARD PERSONNEL &
EQUIPMENT DURING MAINTENANCE OPERATIONS, AND, REPRESENTS THE MINIMUM
REQUIREMENTS. ANY ACTION SHOULD BE PRECEDED BY A HAZARD ANALYSIS TO DETERMINE
ANY ADDITIONAL SAFETY PRECAUTIONS THAT MAY BE NECESSARY TO ENSURE THE SAFETY OF
PERSONNEL AND EQUIPMENT.
NOTE: USE OF THE FOLLOWING LOCKOUT PROCEDURE IS MANDATORY WHEN COMPLETING

MAINTENANCE OR REPAIRS.
LOCKOUT PROCEDURE
1)
THE LOCKOUT PROCESS MUST BE PERFORMED BY AUTHORIZED PERSONNEL ONLY.
2)
INFORM ALL EFFECTED PERSONNEL OF YOUR INTENT TO LOCKOUT AND SERVICE THE
SPECIFIED MACHINE.
3)
SHUT OFF MACHINE POWER USING NORMAL SHUT DOWN PROCEDURES.
4)
TURN OFF THE MACHINE AND INDIVIDUAL BUILDING CIRCUIT BREAKERS. MAKE SURE ALL
STORED ELECTRICAL ENERGY IS RELIEVED. (EG: SPINDLE & AXIS SERVO CONTROLLERS)
5)
CONNECT THE LOCKOUT DEVICE AS SHOWN IN FIGURE 1, AND ATTACH THE APPROPRIATE
TAG AT THE MACHINE CIRCUIT BREAKER. THE TAG MUST IDENTIFY THE PERSON
RESPONSIBLE FOR THE LOCKOUT. THIS WILL ENSURE THAT POWER CANNOT BE
RESTORED BY ANYONE ELSE.
6)
TEST THE MACHINE TO VERIFY THAT MACHINE SYSTEMS DO NOT OPERATE IN ANY WAY.
ONCE TESTING IS COMPLETE, MAKE SURE ALL SWITCHES ARE IN THE OFF POSITION.
CONFIRM THAT THE LOCKOUT DEVICES REMAIN PROPERLY INSTALLED.
7)
COMPLETE THE REQUIRED MAINTENANCE OPERATIONS.
8)
MAKE SURE ALL PERSONNEL ARE CLEAR OF THE MACHINE.
9)
REMOVE THE LOCKOUT DEVICE. MAKE SURE ALL PERSONNEL ARE AT A SAFE LOCATION
BEFORE RESTORING MACHINE POWER.
PADLOCK
FIGURE
S-4
INSTALLATION PRECAUTIONS
The following subjects outline the items that
directly affect the machine installation and startup. To ensure an efficient and timely installation,
please follow these recommendations before
calling to schedule a service engineer.
6)
ENVIRONMENTAL REQUIREMENTS
Avoid the following places for installing the
machine:
1) Avoid exposure to direct sunlight and/or near a
heat source, etc. Ambient temperature during
operation: 0 thru 45C (32F to 113F).
2) Avoid areas where the humidity fluctuates
greatly and/or if high humidity is present;
normally 75% and below in relative humidity. A
higher humidity deteriorates insulation and
might accelerate the deterioration of parts.
3) Avoid areas that are especially dusty and/or
where acid fumes, corrosive gases and salt are
present.
4) Avoid areas of high vibration.
5) Avoid soft or weak ground (minimum load
bearing capacity of 1025 lbs./ft2)
In pouring grout, fasten the leveling block

base plates with the collar retaining screws
to prevent the base plates from dropping.
When the grout has completely hardened,
level the machine properly, and tighten M24
nuts to secure the machine to the
foundation.
Note:
The machine must be anchored to the
foundation with J-bolts, expansion bolts or
other suitable method.
The machine accuracy and alignment
specifications quoted by Mazak can usually
be obtained when the minimum foundation
requirements are met. However, production
of close tolerance parts requires the use of an
appropriate certified foundation. Foundations
that do not meet certified specifications may
require more frequent machine re-leveling and
re-alignment, which can not be provided
under terms of warranty.
If any of these conditions cannot be met,
contact the nearest Mazak service office
immediately.
FOUNDATION REQUIREMENTS
For high machining accuracy, the foundation
must be firm and rigid.
This is typically
accomplished by securely fastening the
machine to the foundation with anchor bolts. In
addition, the depth of concrete should be as
deep as possible (minimum 6 - 8 inches). Note
the following:
1) There can be no cracks in the foundation
concrete or surrounding area.
2) Vibration proofing material (such as asphalt)
should be put all around the concrete pad.
3) Form a cone in the foundation for J-bolt
anchors, or use expansion anchors.
4) With the foundation anchor bolt holes open
pour the primary concrete at a minimum
thickness of 6 - 8 inches. Typically, the
concrete must have a minimum compression
rating of 2500 lbs. @ 250 lbs. compression
and strengthened with reinforcing rods. When
the concrete has cured, rough level the
machine, and install the J-bolts, leveling blocks,
etc., and pour grout into foundation bolt holes.
5) Mix an anti-shrinkage agent such as Denka
CSA with concrete, or use Embeco grout to fill
the foundation bolt holes.
S-5
WIRING
1) Use
only
electrical
conductors
with
performance ratings equivalent or superior.
2) Do not connect any power cables for devices
which can cause line noise to the power
distribution panel, such as arc welders and high
frequency machinery.
3) Arrange for a qualified electrician to connect
the power lines.
4) Incoming supply voltage should not deviate
more than 10% of specified supply voltage.
5) Source frequency should be2 Hz of nominal
frequency.
Desirable Independent Grounding:
NC
Machine
Earth resistance:
Less than 100 ohms
Common Grounds:
Resistance to ground
= 100 the number of
devices connected to
the grounding (ohms)
[ CAUTION ]
VERIFY THE ACTUAL MACHINE ELECTRICAL

Note: Never ground equipment as shown below:
POWER REQUIREMENT AND THE MAIN

TRANSFORMER RATING (IF APPLICABLE), AS
WELL AS THE LOCAL ELECTRICAL CODE
BEFORE SIZING AND INSTALLING THE
INCOMING POWER WIRING.
PLEASE SEE THE ADDITIONAL CAUTIONS ON
THE FOLLOWING PAGE.
GROUNDING
1) An isolated earth ground with a resistance to
ground of less than 100 ohms is required.
Typically, a 5/8 copper rod, 8 feet long, and
no more than 5 feet from the machine, is
sufficient.
Building grounds or multiple
machines grounded to the same ground rod,
are not acceptable.
2) The wire size should be greater than AWG
(American Wire Gauge) No. 5 and SWG
(British Legal Standard Wire Gauge) No. 6.
000X713-KY 11/98
S-6
CAUTION
A step-down transformer is optional on some machine models. Be certain to

verify the transformer Kva rating (where applicable), as well as local electrical
code requirements before sizing and installing the incoming power wiring.
Machines not equipped with a main transformer are wired for 230 VAC, 3 phase.
The end user must supply a step-down transformer where factory electrical
power varies more than 10% of the 230 VAC rating.
NOTE:
Step-down or voltage regulating transformers are external (peripheral) to the
machine tool and are considered the primary input line (source) for the machine.
Local electrical code or practice may require a circuit breaker or other switching
device for the isolation of electrical power when this type of transformer is used.
In such cases, the machine tool end user is required to supply the necessary
circuit breaker or switching device.
FAILURE TO COMPLY CAN RESULT IN PERSONAL INJURY AND DAMAGE TO THE

MACHINE. IF ANY QUESTION EXISTS, CONTACT THE NEAREST MAZAK SERVICE
CENTER FOR ASSISTANCE.
S-7
WARNING
MAZATROL CNC CONTROLLERS PROVIDE PARAMETER SETTINGS TO LIMIT SPINDLE

RPM. THESE SETTINGS ARE BASED ON THE MAXIMUM SPEED SPECIFIED BY THE
CHUCK/ACTUATOR MANUFACTURER.
MAKE SURE TO SET THESE PARAMETERS ACCORDING TO CHUCK SPECIFICATION
WHEN INSTALLING A CHUCKING PACKAGE. ALSO, STAMP THE MAXIMUM SPINDLE
RPM ON THE CHUCK IDENTIFICATION PLATE LOCATED ON THE MACHINE TOOL
COVERS.
REFERENCE THE CNC PARAMETER MANUAL SUPPLIED WITH THE SPECIFIC MACHINE
TOOL TO IDENTIFY THE REQUIRED PARAMETERS TO CHANGE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO
THE MACHINE, SERIOUS INJURY OR DEATH.
IF ANY QUESTIONS EXIST, CONTACT THE NEAREST MAZAK SERVICE CENTER FOR
ASSISTANCE.
WARNING
MAZAK MACHINES ARE ENGINEERED WITH A NUMBER OF SAFETY DEVICES TO

PROTECT PERSONNEL AND EQUIPMENT FROM INJURY AND DAMAGE.
DO NOT REMOVE, DISCONNECT, BYPASS OR MODIFY ANY LIMIT SWITCH, INTERLOCK,
COVER, OR OTHER SAFETY FEATURE IN ANY WAY, EITHER MECHANICALLY OR
ELECTRICALLY.
ASSISTANCE.
S-8
WARNING
MAZAK MACHINES ARE ENGINEERED WITH A NUMBER OF SAFETY DEVICES TO

PROTECT PERSONNEL AND EQUIPMENT FROM INJURY AND DAMAGE.
MACHINE OPERATOR DOORS AND COVERS ARE DESIGNED TO WITHSTAND
ACCIDENTAL IMPACT OF A BROKEN INSERT WHERE A MAXIMUM WEIGHT INSERT AT
MAXIMUM TOOL DIAMETER IS RUNNING AT MAXIMUM SPINDLE RPM
NEVER USE A CUTTING TOOL OR TOOL INSERT THAT EXCEEDS MACHINE
SPECIFICATIONS OR THAT OF A SPECIFIC TOOL HOLDER ITSELF, WHICHEVER IS LESS.
THIS RESTRICTION APPLIES TO DIAMETER, WEIGHT, MAXIMUM SPINDLE RPM,
MAXIMUM CUTTING TOOL ROTATION SPEED, ETC.
FOR COMPLETE SPECIFICATIONS, MAKE SURE TO REFERENCE OPERATION,
MAINTENANCE AND DETAIL SPECIFICATION DOCUMENTATION SUPPLIED WITH THE
MACHINE AND BY THE TOOLING MANUFACTURER.
NOTE: THE MAXIMUM INSERT WEIGHT FOR MAZAK MACHINES IS 20 gf. (0.04 lbs.).
ASSISTANCE.
S-9
WARNING
BEFORE STARTING OPERATION, CHECK THAT THE WORKPIECE IS SECURELY MOUNTED

IN A VISE OR A SUITABLE FIXTURE. BE CERTAIN THAT THE MOUNTING IS SUFFICIENT
TO WITHSTAND CUTTING FORCES DURING WORKPIECE MACHINING.
ASSISTANCE.
WARNING
CONFIRM PROPER WORKPIECE FIXTURING/CLAMPING, TOOL SETUP AND THAT THE

MACHINE DOOR IS SECURELY CLOSED BEFORE THE START OF MACHINING.
VERIFY ALL SAFETY PRECAUTIONS OUTLINED IN THIS MANUAL BEFORE USING THE
FOLLOWING CUTTING CONDITIONS:
-
CUTTING CONDITIONS THAT ARE THE RESULT OF THE MAZATROL FUSION 640
AUTOMATIC CUTTING DETERMINATION FUNCTION
CUTTING CONDITIONS SUGGESTED BY THE MACHINING NAVAGATION FUNCTION
CUTTING CONDITIONS FOR TOOLS THAT ARE SUGGESTED TO BE USED BY THE

MACHINING NAVAGATION FUNCTION

ASSISTANCE.
S-10
CENGDB0551E
DOOR INTERLOCK SAFTY SPEC.
Determined by YMW Eng. H.Q. 99/9/1

Revised by YMC Prod. Eng. 99.10.28
MACHINING CENTER
DOOR
MODE
OPEN
MANUAL
AUTO
CLOSE
I
V
OPEN
MANUAL
Prohibit
Prohibit
Prohibit
Prohibit
Prohibit
I (ON)
Limit the rapid override. Max is 12%.
Prohibit to run chip spiral conveyor.
Can run spindle JOG.
Can run spindle Orient.
Can operate manual ATC.
to move axis.
to start spindle running.
to operate manual ATC.
to operate manual Pallet Changer.
to run chip spiral conveyor.
Prohibit cycle start.


Door is always locked. Door lock can be released by pushing DOOR UNLOCK SW on operator panel.
But, it can not release in operating ATC/Pallet changer/Axis/Spindle.
Prohibit
Prohibit
Prohibit
Prohibit
Prohibit
AUTO
CLOSE
SET UP SWITCH
O (OFF)
Limit the rapid override. Max is 12%.

Chip spiral conveyor would stop.
Can run spindle JOG.
Can run spindle Orient.
Can operate manual ATC.
to move axis.
to start spindle running.
to operate manual ATC.
to operate manual Pallet Changer.
to run chip spiral conveyor.
Door is always locked. Door lock can be released by pushing DOOR UNLOCK SW on operator panel.
But, it can not release in auto operation running except single block stop or feed hold stop or M00 program
stop or M01 optional stop and spindle stop. If not, Alarm displayed Door open invalid.
If release the lock by note(*1), Alarm will occur
then stop the all motion.

MANUAL
No Limitation.
No Limitation.
AUTO
No Limitation.
Can not run auto operation.
TURNING CENTER
SET UP SWITCH
DOOR
MODE
O (OFF)
I (ON)
Can operate CHUCK, TAILSLEEVE ,

STEADY REST for Loading workpiece.

Can NOT operate Spindle, Axis, Turret,

MANUAL Coolant, ToolEye, Partscatcher,
Chip Conveyor.
Can not operate Spindle running, but

Can operate Spindle JOG and Spindle Orient.
Limitation of speed for axis movement .
(Override is 10% max.)
1 step index only for turret.
OPEN
AUTO
CLOSE
->
OPEN

Can not run Auto-operation.

MANUAL Can not open the front door in Spindle running, Axis moving, Auto-running( Cycle start, Feed hold ) due to
&
Mechanical locking system. (Except Single Block Stop or M00 program stop or M01 optional stop)
AUTO
But, if release the lock by note(*1), Alarm will occur then stop the all motion.
MANUAL No Limitation.
CLOSE
AUTO
No Limitation.
No Limitation.
*1 : Door lock mechanism can not be released in machine stop by NC power OFF.
If it is necessary to release the lock such as emergencies, the lock can be released by operating the
supplementary lock release mechanism of the main body of the safety door lock switch.
*2 : Override Limitation of Rapid speed of AXIS
Machining Center : 12%. Turning Center : 10%.
*3 : Chip Conveyor and Coolant should stop in the door open.
PED-EDS-001
S-11
CENGDB0551E
APPENDIX
SWITCH PANEL for M640M (Machining Center)
MACHINE SET UP
SWITCH
SWITCH PANEL for M640MT/T (Turning Center)
PED-EDS-001
S-12
DOOR UNLOCK
SWITCH
a
aa
a
a
aa
a
a
aa
aa
a
a
a
aa
a
a
aa
a
a
a
aaa
a
a
a
aa
a
a
a
a
aa
a
a
a
a
aa
a
a
aa
a
a
aa
aa
a
a
aa
aa
a
a
a
aa
a
a
aa
a
a
aa
aa
a
a
aa
aa
a
a
a
aa
a
a
a
a
a
a
aa
aa
a
aa
a
aa
a
a
aa
aa
a
a
a
aa
a
a
aa
a
a
aa
aa
a
a
aa
aa
a
a
aa
aa
a
a
a
aa
a
a
aa
a
a
aa
aa
a
a
aa
aa
a
a
a
aa
a
a
aa
a
a
aa
aa
a
a
aa
aa
a
a
a
aa
a
a
aa
a
a
aa
aa
a
a
aa
aa
a
a
a
aa
aa
a
a
a
a
aa
a
a
aa
aa
a
a
a
a
a
aa
aa
a
a
a
a
aa
a
a
aa
aa
a
a
a
a
a
aa
aa
a
aa
a
aa
a
a
aa
aa
a
a
a
a
a
aa
a
aa
a
a
aa
a
a
a
aa
aa
a
a
a
a
aa
a
a
aa
a
a
aa
a
a
a
aa
aa
a
a
a
a
aa
a
a
aa
aa
a
a
a
a
a
aa
aa
a
aa
a
aa
a
a
aa
aa
a
a
a
a
a
aa
aa
a
a
aa
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
aa
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
a
a
a
a
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
MACHINE DOCUMENTATION
CUSTOMER EVALUATION
The Other Thoroughbred From Kentucky
Your opinion is important to enable us to issue documentation that will fit your needs.
Thank you for taking the time to supply this information.
Date:
Machine Type:
Machine Serial#:
NC Type:
Customer:
Reported By:
Address:
Position:
Telephone#:
Manual Publication #:
Excellent
Good
How well is the documentation suited to your needs?
Were you able to find the necessary information easily?

How well are the manuals organized?
How easy are the manuals to understand?

Are the illustrations helpful?
Overall, how do you rate the documentation?
What did you like about the documentation? How can it be improved?
RETURN TO:
SF-202Xa
MAZAK Corporation
Technical Publication Dept.
8025 Production Drive
Florence, Kentucky 41042
Adequate
Fair
Poor
Notes:
Introduction
Thank you for purchasing the Mitsubishi numericcontrol unit.
This manual describes the handling and caution points for using AC
thisservo.
Incorrect handling may lead tounforeseen accidents, so always read this instructionmanual
thoroughly to ensure correctusage.
Make sure that this instruction manual is delivered to the end user. Keep this manual in a safe
place for future reference.
Precautions for safety

Please read this manual andauxiliary documents before starting installation,
operation,
maintenance or inspection to ensurecorrect usage. Thoroughly understand the device, safety
information andprecautions before startingoperation.
The safety precautions in this instruction manual areranked as "WARNING" and "CAUTION".
When a dangeroussituation may occur if handling is mistaken

leadingtofatal or major injuries.
When a dangerous situation may occur if handling is mistaken
leading to mediumor minor injuries, or physical damage.
1-
may lead to major results depending on

Note thatsome items described as
the situation. In any case, important information that must be observedis described.
The numeric control unit is configured

of the control unit, operation board,servo amplifier,
spindle amplifier, powersupply + servo drive or spindle drive, servomotor, and spindle motor,
etc.
In this manual, the following items are generically called the "servomotor".
Servomotor
Spindle motor
In this manual, the following items are generically called the"servo amplifier".
Servo amplifier
Spindle amplifier
Power supply + servo drive or spindle drive
Changes in terminal names

The terminal names have been changed in two stages as shown below.
2
m
.-c
t-
Prior to March 95
April 95 to March 96
R
S
R/L1
s / L2
T / L3
L+ 1 P
L-/ N
L11 / Ro
L21 / s o
T
P
N
Ro
so
Following April 96
(MDS-B Series)
Ll
L2
L3
L+
LL11
L2 1
I
M6478-ES
For Safe Use

1. Electric shock prevention
/1\ WARNING
A
A
Do not open the front cover whole the power

is ON or during operation. Failure to observe this
could lead to electric shocks.
A
A
Do not remove the front cover even when the power

is OFF unless carrying out wiring work or
periodic inspections. The inside
of the servo amplifier is charged, and can cause electric
shocks.
A
A
A
Ground the servo amplifier and servomotor

with Class 3 grounding or higher.
Do not operate the unit with the front cover removed. The high voltage terminals and charged
sections willbe exposed, and can cause electric shocks.
Wait at leastI O minutes after turning the power

OFF before starting wiring or inspections.
Failure to observe this could lead to electric shocks.
Wiring and inspecbon

work must be done by a qualified technician.
Wire the servo amplifier and servomotor after installation. Failure to observe this could lead to
electric shocks.
Do not touch the switches

with wet hands. Failure to observe
this could lead to electric shocks.
Do not damage, apply forcible stress, place heavy items or engage the cable. to
Failure
observe
this could lead to electric shocks.
2. Fire prevention
CAUTION
Install the servo amplifier, servomotor and regenerative resistor on noncombustible material.
Direct installation on combustible material or near combustible materials could lead
to fires.
Shut off the power onthe servo amplifier sideif a fault occurs in the servo amplifier. Fires could
be caused if a large current continues to flow.
Shut off the power with an error signal when using the regenerative resistor. The regenerative
resistor could abnormally overheat and cause a fire due to a fault in the regenerative transistor,
etc.
...................................................................................................................
I Outline
1.1 Features .............................................................................................................
1.2 System configuration ..........................................................................................
2 System Start Up
3 Addition and Replacement Methods
of Units and Parts........................................
3.1 Unit replacement ................................................................................................
3.2 Servomotor encoder ............................................................................................
3.2.1
OHUOHA typeencoder .............................................................................
3.2.2
OSWOSA type encoder .............................................................................
3.3 Battery unit .........................................................................................................
3.4 Unit fan ...............................................................................................................
4 Daily Maintenance
4.1 Tools formaintenance ........................................................................................
4.2 Periodic inspection ..............................................................................................
5 Maintenance Parts
6 Noise Filter
.........................................................................................................
......................................................................................................
.....................................................................................................
.
.................................................................................................................
I1.MDS-A-CV MDS-B-CV MDS-A-CR Power Supply Section
I-?
I1
1-3
1-7
1-9
1-9
1-12
1-12
I-?
4
1-17
1-18
1-20
1-20
1-20
1-22
1-25
.........................................................................................................
I Troubleshooting
1.1 Status display .....................................................................................................
1.2 Troubleshooting per power supply alarm ...........................................................
1.3 Power supply warnings .......................................................................................
11-1
11-1
11-4
11-17
I11.MDS-A-Vx MDS-B-Vx
Servo System Section

1 MDS-CI-VlN2 Servo Drive Unit................................................................................
1.1 Points changed from B Series .............................................................................
1.1.1
1.1.2
Compatible detectors and compatible motors ............................................

2-system compliance (standard amplifier (MDS-B-VlN2) mode and
high-gain amplifier (MDS-9-Vl4N24) mode).............................................
2 Adjustment Procedure ..............................................................................................
2.1 Initial adjustment .................................................................................................

2.1.1Confirmation
of parameters .......................................................................
2.1 -2 Adjustment of optimum acceleration/deceleration time constant ..............
2.1.3
Adjustment of speed gain ..........................................................................
2.1.4
Zeropointreturn ........................................................................................
2.1.5
Adjustment of absolute position detection .................................................
2.2 Adjustmentdetails ..............................................................................................
2.2.1
Vibration or vibration sounds occur ...........................................................
2.2.2 The cutting surface precision is poor. The roundness is poor ................
2.2.3 Overshooting occurs during positioning . A limit cycle occurs.................
2.2.4 Accumulated feed occurs with pulse feed .................................................
2.3 Adjustment of special functions ..........................................................................
2.3.1 High precisioncontrol mode ......................................................................
3 Troubleshooting (MDS-A/B Series) ..........................................................................

3.1
3.2
3.3
Status display .....................................................................................................

Troubleshooting per servo alarm ........................................................................
Precautions..........................................................................................................
4.1
Servo warnings and servo alarms .......................................................................
4.Troubleshooting (MDS-CI Series)

............................................................................
5 Appendix
5.1
5.2
...................................................................................................................
Changing from closed loop to semi-closed loop .................................................

Servo system configuration table .......................................................................
I
111-1
111-1
111-1
111-2
111-3
111-3
111-3
1114
111-6
111-8
111-9
111-11
111-11
111-1 2
111-13
111-14
111-1 5
111-1 5
111-1 7
111-17
111-23
111-52
111-53
111-53
111-84
111-84
111-86
IV. MDS-A-SP MDS-B-SP
Spindle System Section
..............................................................................................
I.Adjustment Procedure
1.1Trialoperation
.....................................................................................................
1-2 Adjustment of orientation ....................................................................................
1.2.1
Operation
..................................................................................................
1-2.2 Operation sequence ..................................................................................
1.2.3
Encoderorientationstop positions ............................................................
1.2.4
Parameter block diagram for orientation ...................................................
1-2.5 Preparation for adjustment of motor built-in encoder orientation ..............
1-2.6
Preparation for adjustment of encoder orientation ....................................
1.2.7
Preparation for adjustment of magsensor orientation ...............................
1-2.8Adjustment
of orientation ..........................................................................
1-2.9 Adjustment of sew0 rigidity .......................................................................
1-2.10 "Delay/advance control" and "PI control" application ................................
1.2.11 Troubleshooting during orient error ...........................................................
1.3 Synchronous tap adjustment ..............................................................................
1-3.1 Synchronous tap operation adjustment .....................................................
1.3.2
Troubleshooting for synchronous tap error ...............................................
2.Troubleshooting
2.1 Introduction .........................................................................................................
2.2 First step of troubleshooting ...............................................................................
2.3 Second step of troubleshooting ..........................................................................
2.4 Alarm and warning table .............................................................................. :......
2.5 Approach per phenomenon ................................................................................
2.5.1
When alarm or warning is displayed on the 7-segment display ................
2.5.2
When alarm or warning is not displayed on 7-segment unit .....................
2.6 Periodic inspection ..............................................................................................
2.6.1
Inspection of controlunit ...........................................................................
2.6.2
Inspection of motor ....................................................................................
.........................................................................................................
3. Disassembly and Assemblyof Motor

3.1
3.2
.............................................
.........................
Disassembly and assembly of SJ type AC spindle motor ...................................

Disassembly and assembly of SJ-N type AC spindle motor ...............................
.........................................
.................
4. Installation of Orientation Position Detector

4 .I Magnesensor 1-point orientation ........................................................................
4.1.1Magnetand
sensor ...................................................................................
4.1.2
Orientation of magnet and sensor head ....................................................
4.1.3
Caution on installation of magnet ..............................................................
4.1.4 Caution on installation
of sensor head ......................................................
4.1.5
Types and outside dimensions of magnesensor........................................
4.2 Encoder orientation (4096 points) ......................................................................
4.2.1
Configuration
.............................................................................................
4.2.2Outside
dimensions ...................................................................................
5. Contour Control (C-axis Control) Encoder
5.1Separate stand-type encoder .............................................................................
5.1.1
Name: OSE9OK + 1024 BKO-NC6336HOl ............................................
5.1 -2 Outside dimensions ...................................................................................
5.1.3
Connectors ................................................................................................
5.1.4
Mechanical specifications ..........................................................................
5.1.5
Handling, installation and operation of encoder ........................................
5.2 Built-in encoder ...................................................................................................
5.2.1
Model : MBE-9OK ......................................................................................
5.2.2
Model : MHE-9OK ......................................................................................
6.Appendix
6.1Parameter
list .....................................................................................................
..............................................................
...................................................................................................................
ii
iv-1
Iv-1
rv-2
1v-2
1v-3
1v4
1v4
1v-5
1v-6
1v-8
I
V
0I
1v-11
1v-11
I
V
2I
1v-15
I
V
5I
1v-18
N-19
Iv9I
Iv9I
rv-21
1v-23
1v-24
1v-24
1v-38
1v-43
1v-43
1v-44
1v45
N-45
1v-53
1v-62
1v-62
1v-62
1v-63
1v-67
1v-67
1v-69
1v-71
1v-71
1v-72
1v-73
1v-73
1v-73
1v-73
1v-73
1v-74
1v-75
1v-76
1v-76
1v-76
1v-77
1v-77
3. Injury prevention
A CAUTION
Do not apply a voltage other than that
specified in Instruction Manualon each terminal. Failure to
observe this item could lead to ruptures
or damage, etc.
Do not mistake the terminal connections. Failure to observe this item could lead to ruptures
or
damage,
etc.
Do not mistake the polarity

(0,0).Failure to observe this item could lead to ruptures
or
damage,
etc.
Do not touch the servo amplifier fins, regenerative resistor

or servomotor, etc., while the power is
turned ON or immediately after turning the power OFF. Some parts are heated to high
temperatures, and touching these could lead to bums.
4. Various precuations
Observe the following precautions. Incorrect handling of the unit could lead
faults,
to injuries and electric
shocks, etc.
(1) Transportation and installation
/1\ CAUTION
correctly transport the product according its

toweight.
Use the servomotor's suspension bolts only when transporting the servomotor.
Do not
transport the servomotor when
it is installed on the machine.
Do not stack the products above the tolerable number.

Do not hold the cables, axis
or detector when transporting the servomotor.
Do not holdthe connected power supplyor cables when transporting the servomotor.
Do not hold the front cover when transporting the servo
amplifier. The unit could drop.
Follow this Instruction Manual and install the unit in a place where the weight can be borne.
Do not get on top

of or place heavy objects on the unit.
Always observe the installation directions.
Secure the specified distance betweenthe sew0 amplifier and control panel, or between the
servo amplifier and other devices.
Do not installor run a servo amplifieror servomotor that is damaged or missing parts.
Do not block the intake

or exhaust portsof the servomotor provided with
a cooling fan.
Do not let conductiveobjects such as screwsor metal chips, etc., or combustible materials such
as oil enter the servo amplifier
or servomotor.
The servo amplifier and servomotor are precision devices,
so do not drop themor apply strong
impacts to them.
Ill
A CAUTION
A
Store and use the units under the following environment conditions.
Conditions
Environment
0C to+55"C
(with no freezing)
Ambient temperature
Ambienthumidity
TO
followseparatespecifications
Storage temperature
To follow separate specifications
Storage humidity
Atmosphere
A
A
A
A
A
0C to +40"C
(with no freezing)
8O%RH or less
(with
no
dew
condensation)
-15C to +70C
90% RH or less
(with no dew condensation)
Indoors (Where unit is not subject to direct sunlight)
With no corrosive gas, combustible gas. oil mist or dust
1OOOm or less above sea level
Altitude
Vibration
Servomotor
Servo amplifier
'
Securely fix the servomotor to the machine. Insufficient fixing could lead to the servomotor
slipping off during operation.
Always install the servomotor with reduction gears
in the designated direction. Failure to do
so could lead to oil leaks.
Never touch the rotary sections of the servomotor during operations. Install a cover, etc.,
on the shaft.
When coupling to a servomotor shaft end, do not apply an impact
by hammering, etc. The
detector could be damaged.
Do not apply a load exceeding the tolerable load onto the servomotor shaft. The shaft could
break.
or Service Station.
When storing fora long time, please contact the Service Center
IV
(2) Wiring
A
A
A
A
A
A
A
2
A
A
A
A
CAUTION
Correctly and securely perform the wiring. Failure tosodo

could lead to runawayof the
servomotor.
Do not install a condensing capacitor, surge absorber

or radio noise filter on the output side
of
the servo amplifier.
Correctly connect the output side (terminals
U, V, W). Failure to doso could lead to abnormal
operation of the servomotor.
Do not directly connect a commercial power supply to the servomotor. Doing
so could lead to
faults.
When using an inductive load such as a relay, always connect a diode as a noise measure
parallel to that load.
When using a capacitance load such as a lamp,
ahways connect a protective resistor as
a noise
measure serial to that load.
When connecting a DC relay
for the control output
signals such asthe brake signalor contactor, do
not mistake the polarity of the diode. Failure to
observe this could cause the signals notbeto
output due to a fault
or the protective circuit to fail.
Servo amplifier
VIN
(24VDC)
Control output
Do not connect/disconnect the cables connected between the units while theispower
ON.
Securely tighten the cable connector fixing screw
or fixing mechanism. An insecure fixing could
cause the cable to
f a l l off while the power is
ON.
When use of a shielded cable
is instructed in the connection diagrams, always ground the cable
with a cable clamp, etc.
Always separate the signals
wires from the drive wire and power
line.
Use wires and cables that have a wire diameter, heat resistance and flexibility that conforms to
the system.
so that the battery unit is not mistakenly wired.

Check the cables sufficiently before wiring
The battery in the battery unit could short circuit and be charged due to incorrect wiring, and
could lead to battery ignition, heating, rupture
or generation of toxicgas.
(3)Trial operation and adjustment
CAUTION
A
A
Check and adjust each program and parameter

before starting operation. Failure todo so could
lead to unforeseen operation of the machine.
Do not make remarkable adjustments and changes as the operation could become unstable.
(4) Usage methods
CAUTION
Install an external emergency stop circuit

so that the operation can be stopped and power shut
off immediately.
A
0
A
A
A
Turn the powerOFF immediately if smoke, abnormal noise or

odors are generated from the
spindle motor or spindle amplifier.
Unqualified persons must not disassemble or repair the unit.
Never make modifications.
The brakes (magnetic brakes) assembled into the servomotor are for holding, and must
be not
used for normal braking.
There may be cases when holding is not possible due to the magnetic brake's
or the
life machine
construction (when ball screw and servomotor are coupled via a timing belt, etc.). Install a stop
device to ensure safety on the machine side.
After changing the parameters or after maintenance and inspecbon, atways test the operation
before starting actual operation.
Do not enter the movable range of the machine during automatic operation. Never place body
parts near or touch the spindle during rotation.
Follow the power supply specification conditions given in the separate specifications manual for
the power (input voltage, input frequency, tolerable power failure time, etc.).
A
A
A
Reduce magnetic damage by installing a noise filter. The electronic devices used near the sew0
amplifier couldbe affected by magnetic noise.
Use the spindle motor, spindle amplifier and regenerative resistor with the designated
combination. Failure to do
so could lead to fires
or trouble.
(5) Troubleshooting
/1\ CAUTION
If a hazardous situation is predicted during power failure or product trouble,ause

servomotor
with magnetic brakes or install an external brake mechanism.
Use a double circuit configuration
Shut off with NC brakecontrol PLC output.
signal.
Servomotor
I
RA1
EHG
Always turn the input power OFF when an alarm occurs.

Never go near the machine after restoring the power after a failure, as the machine could start
suddenly. (Design the machineso that personal safety can be ensured even if the machine
starts suddenly.)
VI
(6) Maintenance, inspection and part replacement
A CAUTION
Always backup the servo amplifier programs and parameters before starting maintenance
or
inspections.
The capacityof the electrolytic capacitor will drop due to deterioration.
To prevent secondary
damage dueto failures, replacing this part every five years when used under a normal
environment is recommended. Contact the Service Center
or Service Stationfor replacemet.
Do not perform a megger test (insulation resistance measurement) during inspections.
If the batterylow warning is issued, save the machining programs, tool data and parameters
with an input/output unit, and then replace the battery.
Do not short circuit
or charge the battery unit connector terminals.
Do not deform, heator
incinerator the battery unit
or disassemble the internal battery.
Failure to observe this could leadfires,
to heating, ruptureor generation of toxic gases.
When storing the battery unit, avoid places subject to direct sunlight, high temperatures
or
high humidities. Failure to observe this could lead to leaking
or rupture of the internal battery.
A
1 CAUTION
A
/c\
A
Treat this unit as general industrial waste.

If the heat radiating fins are protruding
from the rear of theMDS Series, substitute Freon is
used. Donot disposeof this typeof unit as general industrial waste. Always contact the
Service Stationor Service Centerfor disposal.
Do not disassemble the spindle motor or spindle amplifier.
Plug thegaps on the battery unit with non-conductive material such as cellophane tape before
disposing.
Disposal in the original state allow other metal chips entering the internal battery, and lead to
ruptures or fires.
Dispose of the battery according to local laws.
(8) General precautions

The drawings givenin this Specifications and Maintenance Instruction Manual
show the covers and safety
partitions, etc., removedto provide a clearer explanation. Always return the covers
or partitions to their
respective places before starting operation, and always follow the instructions given
thisIn
manual.
VI I
. ..-
I. MDS-A Series
MDS-B Series
Servo/Spindle System Configuration Section
I
1. Outline
I Outline
The MDS-A Series is a drive system that corresponds to the
MELDAS M500 Series NCthat has been
developed to totally connected the servo drive and spindle drive sections. The MDS-B Series is the
successor to the MDS-A Series, and has been developed to satisfy European Safety Standards. This
Series has the following features.
The MDS-C1 Series is a drive system compatible with the NC system. This high-performance, compact
series is compatible with the MDS-B Series (some changes have been made).
1.I Features
Compact and lightweight
The converters that were conventionally built in each servo and spindle drive have been integrated
into one unit. The drive system volume, installation area and weight have been drastically reduced
with the incorporationof high density mounted electronic parts IGBT-IPM (Intelligent Power Module)
and the high performance heat radiating fin.
Standardization of dimensions
The outline has been standardized *to the book end type, and by unifying the height and depth
dimensions, installation in cabinets has been made easy. Furthermore, by matching the shape with
the NC unit, an integrated appearance with the NC has been realized.
Low heat generation

By incorporating the IPM and using power supply regeneration in the servo drive, the of
amount
heat
generated has been greatly reduced.
High speed and precision processing
A high speed CPU has been mounted on the control PCB, and
100,000
a pulse/rotation sub micron
detector has been incorporated as a standard to allow faster and more precise interpolation.
By incorporatingthestablepositionloopcontrol
(SHG control)method,havinganoutstanding
response, the positioning time and tracking have been improved and the machine vibration during
acceleration/deceleration has been reduced.
The cutting performance and cutting precision during position control have been improved by using
the high speed CPU also for the spindle drive.
High speed spindle orientation
Smooth operations and minimum orientation times have been realized by using the high speed
orientation method while allows direct orientation from the high speed during the spindle drive.
Features of the MDS-B Series
(a) European Safety Standards compliant
Approval from a thirdpartyapprovalagency
(TUV) hasbeenacquiredinrespecttothe
European Safety Standards (LVD Directives).
(Note that theB Series target models are limited to the
CV (power regenerative power supply),
SP (spindle drive) and
V l N 2 (1/2-axis servo drive.)
Addition of power supply emergency stop input line
With theB Series, the external contactor can be directly shut
off from the power supply even when
the emergency stop hot line from the NC does not function for any reason.
(This function is validated with the rotary switch and connected drive parameter settings. Thus, the
functions doe not change from the conventional functions when used in the same manner as the A
Series.)
1-1
1. Outline
(8) Features of the MDS-C1 Series

1) Highperformance
High-performance sew0 control, equivalent to the high gain amplifier

(B-Vl4N24) is mounted.
2) Compact
The fin outline has been downsized

by incorporating high-efficiency fins and a loss
low compact
IPM, and a thin type drive unitis realized.
3) Reliability
Heat generation has been reduced

by incorporating a low
loss IPM, and the strength of the inner
support structure has been increased by integrating the terminal block with the wiring condu
This has improved the reliability compared to the conventional B Series.
Outline dimensions, installation dimensions, terminal connections

Compatible with the current
B Series.
* Some changes have been made
to the PE terminal position and control terminal position (in
some capacities).
Control function (servo)
Thesystemautomaticallyjudgeswhetherthestandardamplifier
(B-VlN2) or highgain
amplifier (B-V14/V24) is mounted. The parameters are compatible. Refer to the following
pages for details.
* Note that there are some restrictions to the motor end encoder.to the
Refer
following pages
for details.
* The system is shipped from the factory with the high-gain specifications. Refer to the
following pages for details.
Control function (spindle)
The control functions and parameters are both compatible.
* This series canbe used without problem together with the
B Series in the same machine.
1. Outline
I.2 System configuration
WARNING
Always ground the spindle driver and spindle motor with Class
3 or higher grounding.
/1\
CAUTION
1. Correctly connect the power phases(U, VI W) of the spindle amplifier and spindle motor.
Failure to doso could cause the spindle motor to malfunction.
2. Do not apply a voltage other than that specified to each terminal. Failure to observe this could
lead to rupturesor trouble.
The system is composed of the following units:

(1) Power supply unit
This unit converts the 3-phase AC power supply intoDC
a power supply for
inverter drive, and regenerates the energy into power or resistance when
decelerating the motor.
(2) Spindle drive unitThis is the inverter unit for spindle motor drive.
(3) Servo drive unit
This is the inverter unit for servomotor drive.
(4) B a t t e r y u n i t = = - - - - - This unit is used to save the datain the absolute position detection system.
---
-- - 0
Drive section wiring system drawing
/I\
CAUTION
1. Shut off the power on the spindle amplifier side if a fault occurs in the spindle amplifier. Fires
flow.
could be caused if a large current continues to
2. Shut off the power with a

fault signal. The regenerative resistor could abnormally overheat and
a fault in the regenerative transistor, etc.
cause a fire due to
1 3.
i
1
Configure the magnetic brake operation circuit as a double circuit

so that tit will function with
the emergency stop switch even when the power supply is OFF, and alarm has occurred or
whentheservoONsignal
is OFF.
Wire the power and main circuit as shown on the next page. Always use a no-fuse breaker
for (NF)
the power input wire.
1-3
.-
. .. .
I.Outline
Observe the following pointsfor the MDS-C1-V1N2 servo drive unit.
CAUTION
<Control mode changeover>

(1) The 2-system compatible software is compatible from Version A1(BND-582WOOO-Al).
Version A0 is not compatible with the standard amplifier mode.
It is compatible only with the
high-gain amplifier mode.
(2) Whether to start the servo amplifier in the standard amplifier compatible mode or the highgain amplifier compatible mode is judged by the servo parameters
SVOO9 to SV012 and
SV033 setting values setin the machine.
(3) When the control mode has been changed to the high-gain amplifier (MDS-B-VI4N24) mode
afterremountingfromthestandardamplifier(MDS-B-VlN2),theparametersmustbe
changed for the high-gain amplifier and the servo parameters must be adjusted.
details.
Refer to the section"111. Servo System, section 1.1.2 2-system compliance" for
'
CAUTION
<Servo alarm "7F">
The actual mode is changed between the standard amplifier mode and high-gain amplifier
mode when the 200V power
is turnedON. Thus, if the above servo parameters are changed,
the alarm"7F" will occur, and the restarting of the power will be requested.
Alarm "7F" is a status flag that occurs when the amplifier mode state changes. It does not
indicate an amplifier fault like the other alarms. (Alarm "7F" is not counted as a fault.)
The system is shipped from the factory with the high-gain amplifier mode. Thus, the amplifier
state after the machine is installed will be as follows.
Standard amplifier parameters + First time200V power is turnedON.
Alarm "7F"
+Second and subsequent time 200V power
is turned ON.
Normal connection
High-gain amplifier parameters+First and subsequent time 200V poweris turnedON.
Normal connection
When using the standard amplifier mode (using the standard amplifier parameters),
the 20OV
power must be turned ON again after the machine is installed. "7F" will appear in the alarm
history, but as"7F"does not indicate an amplifier fault, clear the alarm history and erase the
"7F"record.
If alarm "7F" is detected even afterthe 200V power is turnedON again, an error willbe
detected in the internal memory circuit
(EEPROM). The amplifier mustbe replaced in this
case.
Refer to the section "III. Servo System, section I.I

.2 2-system compliance" for details.
1-4
1. Outline
<MDS-AIB series>
Standard connection
B-V2
NC control
unit
B-v1
A-V1
(1st axis servo drive)(2nd
6-SP
6-CV
A-CV
BV2
A-SP
axis servodrive)(Spindledrive)
A-BT
-lz
60Hz
* Please readthe"MDS-A
Series Specifications BNP-B3759" togetherwiththis
servicing the MDS system.
For V1 and SP
For V2
For CV
Note 1. Starting from production in April 1995, a
Prior to
March 95
R
Ro
I-
so
April 95 to
March 96
L1 I R
L2 I s
L3 I T
L+ I P
L- I N
L11 I R o
L21 I so
GIC3
grounding bar is enclosed with each unit

when shipped. Connect the grounding
wire as shown above, and make sure that
the grounding wiresare not tightened
together.
Note 2. Always install a surge killer on both ends
of the contactor coils.
Note 3. The terminal block names have been
changed in two stages as shown in the
table.
al
Ec
al
1-5
manual when
T
P
N
Following April 96
(MDS-B Series)
L1
L2
L3
L+
LL11
L21
I.Outline
<MDS-Cl series>
Standard connection
NC control
unit
c 1-vl
(1st axis servo drive)
c 1-v2
(2nd axis servo drive)
ClSP
(Spindle drive)
Cl-CV
A-BT
(Powersupply)
(Battery unit)
30
POOVAC
200-23OVAC 6OHz
=Hz
Please read the "MDS SeriesSpecifications

servicing the MDS system.
For V1 and SP
BNP-C3000" together with this manual when
For V2
For CV
I
Note 1. Starting from production in April 1995, a
grounding coveris enclosed with each
unit when shipped. Connect the
grounding wire as shown above, and
make sure that the grounding wires are
not tightened together.
Note 2. Always install a surge killeron both ends
of the contactor coils.
Note 3. The terminal block names have been
changed intwo stages as shown in the
table.
Prior to
I April 95 to I Following April 96
2. System Start Up
2. System Start Up
/1\
WARNING
1. Do not touch the switches with wet hands. Failure to observe this could lead to electric shocks.
2. Do not operate the unit with the front cover removed. The high voltage terminals and charged
sections will be exposed, and can cause electric shocks.
3. Do not open the front cover whole the power

ONisor during operation. Failure to observe this
CAUTION
1. Always check the parameters before starting. Depending on the machine, unforeseen
operation could take place.
2. Do not touch the servo amplifier fins, regenerative resistor or servomotor,

, while
etc.
the power
is turned ON or immediately after turning the power
OFF. Some parts are heated to high
temperatures, and touching these could lead to burns.
. The procedure for starting up the entire system is explained in this chapter.
Refer tothe section for each unit for the individual adjustment procedures.
(1) Connect the units according to the connection drawing. (Refer to 1.2 System configuration wiring
system drawing. Refer to the specifications for details.) Observe the cautions in the specifications
when installing each unit, motor and detector.
(2) Set the rotary switches on each unit. (Refer to the settings below. Refer to the specifications for
details.)
(3) Confirm the wiring and input voltage, etc., and turn
ON the power while the NC emergency stop is
applied. Confirm that theLED displays on each unit are normal. (Refer to following page.)
(4) Confirm that the servo and spindle parameters are set as specified
on the NC screen. (Refer to the
specifications for the parameter definitions and setting methods.)
( 5 ) Release the NC emergency stop and confirm that the movement is normal.
(6) Make adjustments according to each unit section.
If any instabilrty such as runaway of the sew0 axis is sensed with the first machine, lower the
parameter SV013ILMTI value. The limiterwill be applied on the torque and the damage to the
machine canbe reduced.
Rotaryswitchsettings
1)Powerregenerative
type power supply unit
2) Resistanceregenerativetypepowersupply
[ Setting
unitSetting
3) Sewokpindle unit
1-7
-
Setting
0 : Contactor used
I: Contactor notused
0
0 : 1staxis
1 : 2nd axis
1
6 : No. 7 axis
2. System Start Up
Status display
MDS-A-VI (V2)
MDS-B-V1 (V2)
MDS-Cl-VI
-CV
MDS-C1
(V2)
Servo drive unit
30 200/23OVAC ON
MDS-B-SP
MDS-CI-SP
30 200/23OVAC ON
30 200/23OVACON
In initialization
NC power ON
rwer ON
NC pbwer ON
I
Alarm is
displayed
when alarm
occurs
Initial data
communication
with NC
Initial data
communication
with NC
Alarm code
is displayed
whenalarm
BS OFF
I
ReadyON
T]
Emergency
st0
RDY ON
SV OFF
'P
Alarm is
displayed
when alarm
Reaby ON
occurs
RDY ON
SV OFF
pp
SV ONON
BS ON
RDY ON
Normal operation
NO^& operation
Normal operation
NC power OFF
NC power OFF
or emergency
NC p-r
OFF
stop
-L
NC p&er ON
The right segment indicatesthe axis No.

(The No. 1 axis is indicatedin this example.)
I
EmergenIcy stop
NC po&r ON
Wl
I
3. Addition and Replacement Methodsof Units and Parts
3. Addition and Replacement Methods of Units and Parts
/i\
CAUTION
1. Correctly transport the product according to its weight. Doing

so could lead to injuries.
2. Do not stack the products above the tolerable number.
3. Install the unit on non-combustible materials. Installation directly on combustible matters or
near combustible objects could lead to fires.
4. Follow this Instruction Manual and install the unit in a place where the weight can be borne.
5. Do not get on top of or place heavy objects
on the unit. Doingso could lead to injuries.
6 . Use within the designated environmental condition range.
7. Do not let conductive objects such as screwsor metal chips, etc.,or combustible materials
such as oil enter the servo amplifier
or servomotor.
8. Do not block the intakeor exhaust ports of the servomotor provided with a cooling fan. Doing
so could lead to trouble.
9. The servo amplifier and servomotor are precision devices,
so do not drop them
or apply strong
impacts to them.
10. Do not installor run a servo amplifier
or servomotor that is damaged or missing parts.
11. When storing for a long time, please contact the Service Center
or Service Station.
r
Before adding or replacing units

or parts, always turnOFF the main power and confirm that the
CHARGE lamp onthe power supply unitis not lit.
3.1 Unit replacement
CAUTION
1. Do not hold the front cover when transporting the servo amplifier. The unit could drop.
2. Always observe the installation directions. Failure to doso could lead to faults.
3. Secure the specified distance between the spindle amplifier and inner side of the control panel
and the other devices. Failureto do so could lead to faults.
Use the following procedure when replacing the units.

(1) Power supply unit replacement
1) Disconnect the connectors connectedto CN4 and 9.
2) Disconnect the wires connected to L1, L2, L3, @, L+, L-, L l I,L21 and MCI on the terminal
block.
3) Remove the two (four) screws fixingthe unit tothe control panel, and remove the unitfrom the
control panel.
4) Install the new unit following the removal procedurein reverse.
(2) Drive unit replacement (Ex. spindle drive)
1) Disconnect the connectors connected toCNlA, lB,4, 5,6, 7, 8 and 9.
2) Disconnect the wires connected to U, V, W, 6,
L+, L-, L11, L21 on the terminal block.
3) Remove thetwo (four) screws fixing the unit to the control panel, and remove the unit from the
4)
control panel.
Install the new unit following the removal procedure in reverse.
1-9
3. Addition and Replacement Methodsof Units andParts
[Outline drawingfor MDS-A/B series]

(2) Drive unit (for spindle drive)
A-SP-220 to 300
A-SP-04 to 185
B-SP-220 to 300
B-SP-04 to 185

A-CV-37 to 185
B-CV-37 to 185
A-CV-220 to 300
B-CV-220 to 370
)
c
)c
%I %I
L 1 1
L21
L1
21
NCl
11._111
LlL2L30
UIII
L1 L2 L3 0
c>
1-10
rU1V1W7@1
L1
21
[Outline drawing forMDS-Cl series]

c1-cv-37 to 185
(2) Drive unit (for spindle drive)
C1-CV-220 to 300
C1-SP-O4 to 185
:w
L2 1
L1
2 11
KI
1-11
C 1-SP-220 to 300
Iw
L1
2 11
3. Addition and Replacement Methodsof Units andParts
3.2 Servomotor encoder
CAUTION
The MDS-Cl Series is not compatible with the

OHE/OHA encoder (motor end).
(Only MDS-A/B Series)
3.2.1 OHE/OHA type encoder

(I)OHE25K-85,OHA25K-85 (for HA23133 motor)
Installation method
1) Install theM4 screw on the coupling. Make sure that the screw does not protrude on the inside.
2) Remove one ortwo rubber bushings for the motor.
3) Install the O-ring on the encoder spigot section.
4) install the motor detector and insert the key
in the shaft. Make sure that there
is no dirt or burrs
in the key hole at this time, and push the in
key
completely.
5) Install the encoder on the motor. Match the coupling keyway and shaft key position at this time
before inserting. The encoder connector position must be fixed to the motor connector position
or the designated position.
6) Fix the encoder with four
M4 P screws. Align the encoder flange markings and the motor flange
punch position.
7) Install the rubber bushing.
Note) Prevent the coupling screw from loosening.
* The current position will be lost after replacement in the OHA25K-85 type, and initializing
will be required.
Installation procedure drawing
O-ring S75
(2)OHE25K-6,OHA25K4
Installation method
1) Remove the cover screws with aM5 hexagonal wrench and remove the cover.
2) Install the encoder on the motor. Align the motor shaft pin and encoder shaft groove,
and the
encoder flat spring's slotted hole and motor flange pin.
3) Fix the flat spring to the motor with the
M5 screws. (Three positions)
1-12
4) Insert the M6 box screw through the hole on the encoder cover, and fix with six wrenches. Fix
the motor shaft at this time, and tighten the screws
so that the screws will not loosen.
5) Place the seal enclosed with the encoder onto the hole on the encoder cover.
6) Cut thetwo wires from the encoder and wires
the form the motor
to a length that is suitable, and
connect each with joint amplifiers.

7) Remove the cannon connector housing with a special tool, pass through the motor cover hole,
and assemble the housing (including the rubber packing). Fix to the motor cover withM3
four
screws.
8 ) Install the motor cover
to the motor.
M3 screw
M5 screw
M5 box screw
The current position will

be lost after replacement in theOHA25K-4 type, and initializing will be
required.
A 0.5mm2joint amplifier and a cannon connector housing removal toolbe
will
required at this
time.
Name Of
970-901table
tool
Manufacturer
Shell
Rear
nut
tightening
spanner
97D-9011
DDK
Chicago Office
245 West Roosevelt Road, Bldg
. 15
Unit 3,West Chicago, IL60185,U.S.A.
Phone: 708-293-7335 Fax: 708-293-7337
Mountingldismounting of insert
Shell table
(97D-9012)
Rear nut tightening spanner
(97D-9011)
1-13
3. Addition and ReDlacement Methods of Units and Parts
(3) OHE25K-108,OHA25K-108 (for low inertia motor)
,a
O-ring
,
S75
4445 X 0.8 X 15 screw
Detector
HA motor
(Note) If the detector installation direction

is B, C, D, the detector connector must come to the
B, c,
D position shown above.
Mounting method
I ) Install the O-ring(S75) on the detector flange.
2) Install aM4 hexagonal socket screw on the coupling.

3) Align and insert the motor shaft key in the detector
bellow keyway.
4) Align the position mark on the detector and the motor markings.
5 ) Install the detector on the motor. (Use
M5 x 0.8 screws.)
6) Tighten the screw on the keyway to fix the key.

7) Tighten the detector's rubber plug.
(Note) The detector and bellow position
is determined so do not remove the bellow from the
detector.
3.2.2 OSEIOSA type encoder

Note 1. The pole position must be adjusted for the low-inertia motor,
so do not replace the encoder.
Note 2. The IP67 compliant motoris submerge-proof, so do not replace the motor.
Note 3. For the IP65 compliant motor, replace the packing with new packing when replacing the motor.
(1) OSEl04S/l05S, OSAl04S/105S (for HA23133 motor)
Installation method
1) Install the O-ring on the encoder spigot section.

2) Install the encoder on the motor. At this time, align the motor's Oldham position (Oldham
installation screw hole position) and encoder's Oldham mark position. Install the Oldham space
betweenthis.Fixtheencoder'sconnectorpositiontothemotorconnectorpositionor
designated position.
3) Fix the encoder with four

M4 P screws. Align the encoder flange markings and the motor flange
punch position.
* Thecurrentpositionwillbelostafterreplacement
initializing will be required.
in the OSAl04S/I 05s type,and

Align the motots Oldham position and encoder mark
MOtOf
Encoder mark position

Mark
4-M4 X 14
O-ring S75 (When using IP65, replace with the new packing M769D009H01.)
(2) OSEl041105, OSAIW105

Installation method
1) Remove the cover screws with M5
a hexagonal wrench and remove the cover.
2) Install the encoder on the motor. At this time, align the motor shaft pin (Oldham installation
screwholeposition)andtheencoder'sOldhammarkposition.InstalltheOldhamspacer
between this.
3) Fix the motor with fourM4 screws.
4) Connect the two connectors from the encoder with two
the connectors from the motor.
5 ) Remove the cannon connector housing with a special tool, pass through the motor cover hole,
and assemble the housing (including the rubber packing). Fix to the motor cover with four
M3
screws.
6) Install the motor cover to the motor.
Align the motor's Oldham
position and encoder mark
Motor
Motor cover
Encoder
packing.
--
Oldham spacer
4-M4X 18
4-M5 box screw
When using IP65,

replace with the
new

~
~~
The current position will be lost after replacement in the

OHA25K-4 type, and initializing will be
required.
A 0.5mm2 joint amplifier and a cannon connector housing removal tool will be required at this
time.
Mounting/dismounting of insert
3.3 Battery unit

The battery built in the battery unit MDS-A-BT is used to save data in the absolute position detection
system.
o Applicable
battery
: Li battery
o Battery back up time : 7 years (at 265 workdays, 100 holidays)
The back up time will be reduced if there are more holidays or if the
ambient temperature is high.
The batteryis brazed onto the

PCB in the battery unit,
so the battery cannot be replaced by itself. Instead,
the entire unit must
be replaced.
.
Use a M5 screw for installation
166
__
~~
-~
p a t t e r y unit outline drawing
[Replacement procedure]
1. Turn OFF the NF for the input power supply 200/23OVAC, pull out the cable, and remove the
battery unit.
2. Replace the battery unit, and connect the cable.
3. Turn ON the power and confirm the operation.
Note) The backup timeof the built-in backup capacitor in the absolute value detector
OHA25K-
4, -85 and -ET is 20 hours when delivered, and will decrease

by half to ten hours
after five
years of use. Complete the operation within that time.
3.4 Unit 'fan

.
The life of the fan is approximately 5 years during normal use (the life will differ according to the usage
state and environment). Follow the procedure below to replace the fan.
(1) MDS-A/B series
1. Turn OFF the NF for the input power supply 200/23OVAC, wait for the CHARGE lamp on the
power supply unit togo out, and then remove the unit.
2. Remove thetwo fan installation screws on the bottom
of the cooling fin.
3. Remove the connector from the rear of the unit, and replace the fan.
I
L
Remove thetwo screws.
Remove theconnector from theunit.
3. Addition and Replacement Methods

of Units and Parts
(2) MDS-CI series

I.Turn OFF the NF for the input power supply 200/23OVAC, wait for the CHARGE lamp on the
power supply unit to

go out, and then remove the unit.
2. Remove the fan guard from the end of the unit, and remove two
the screws installing the fan.
3. Remove the rubber bushing for the fan power cable, and pull out the connection connector.
4. Disconnect the connection connector, and replace the fan.
71
/ I
Remove the two

screws.
Remove rubber bushing.
1-19
Pull out connection connector and

disconnect connector.
4. Daily Maintenance
WARNING
1. Always wait at least ten minutes after turning the power supplyOFF before starting
maintenance and inspection.
Failure to doso could lead to electric shocks.
2. Maintenance and inspection must be doneby a qualified technician. Failure to observe this
could lead to electric shocks. Contact your nearest Service Center or Service Station for
repairs and part replacement.
4.1 Tools for maintenance
NOTICE
Never perform a megger test (insulation resistance measurement) on the spindle amplifier control
circuit.
(1) Measurement
instruments
.
The following measurement instruments are required to confirm that the correct power
supplied to the servo amplifier and that the servo amplifier wiring
is correct.
Equipment
Tester
Oscilloscope
AC voltmeter
AC ammeter
is being
Application Conditions
Confirm that the wiring to the servo
amplifier is correct before turning
ON
the power.
For general measurement and
troubleshooting.
Measure the AC power voltage. The Measure the AC power voltage being
tolerable differenceis k2Y0 or less.
supplied to the servo amplifier.
Maximum reading lOV, 30V. The DC voltmeter
Measure the DC power voltage.
tolerable difference is+2% or less.
Measure the alternate current being
supplied to the motor.
(2) Tools
Screwdrivers (Large and medium Phillips type, small flat head)
4.2 Periodic inspection

A still type drive unit is being used, but the fan built in the unit and the additional cooling fans must be
inspected periodically.
Theservomotorisbrush-lessandbasicallydoesnotrequiremaintenance,butmustbeinspected
periodically for abnormal noise and vibration.
Recommended periodic inspection items
Item
Cooling fan
(fhn built-in unit)
and additional
cooling fan
(outside unit)
Terminal block
screws
Cables and
connectors
Inspection
frequency
Monthly
As
necessary
As
necessary
1. Can the fan be rotated easily by hand?Clean or replace the

2. Does the fan rotate properly when the fan
power is ON?
3. Is the fan dirty with oil or dirt?
4. Do the bearings make abnormal
sounds?
Tighten and clean
I . Are the screws loose?
the
screws
2. Are the screws dirty with oil
or dirt?
1. Is there any damage or scratches, etc.7Replace the cable
2. Are the connectors loose?
Tighten the
connectors
1. The battery life is
7 years under normal Replace the unit
use. This will differ according to the
usage environment (temperature,
usage frequency, etc.).
Is there any abnormal sound or vibration?
~
Batter Jnit
Every
7 years
Motor Sound,
vibration
Temperature
Insulation
Monthly
Remedies
Inspection details
Monthly
TwiceQear
~ _ _
Are the motor bearings or frame hot when

touched by hand?
Is the resistance1MS2 or higher when
insulated with a500V megger tester
between the motor frame and motor
terminals (U, V, W). (Remove the motor's
cannon plug before measuring).
~~
5. Maintenance Parts
Part
Q'ty
qeplacement
time
5 years
an
luitt-in
nit)
'FA4018-BH20 IAB-CV- 37
55
iKO-NC6855H01
75
VB-v1- 35
VB-v2- 201
0
2020
VB-SP- 22
37
'FA-801 8-BH20 3-V1-45
LKO-NC6855H02 2/B-V2- 3510
3520
3535
3-V2- 4520
4535
Style
Electro7 ics
w - S P - 55
75
110
9/B-cv-110
JS80D22-T
5KO-NC6855H21 9-v145
9-SP-110
[oldt
ype)
W C V - 150
592822-T
185
3KO-NC6855H22
W V 1 - 70
90
W S P - 150
185
JS12D22-T
3KO-NC6855H23
m-cv-220
260
300
B-CV-370
B-V1- 110
150
A/B-SP- 220
260
300
C1 -CV- 150
MMF-09C24TS185
3N4
3KO-NC5332H14 c 1-cv-220
260
300
MELCO
TECHNOREX
370
C1-SP/H- 150
185
220
2605
300:
C1-V1- 70
90
110
150
C l -V2-7035
7045
7070
Remarks
h e fan life will differ
ccording to the
sage conditions.
m e additional
cooling fans must
be prepared by the
machine maker.
(Refer to the
specifications)
No.
1
Part
Applicable
unit
Type
Fan
MMF-06F24ES- I C1-CV-110
(built-in RN5
unit)
BKO-NC5332H12
110
150s
c 1-SP/H- 260
300
c 1-v1-45
C1 -V2-3535
4520
4535
7070s
4545
MMF-04C24DSc 1-SP/H- 22
ROE
37
BKO-NC5332Hll c1-v1- 20
c1-Vl- 35
45s
70s
c 1-v2-2010
2020
351OS
35208
Battery MDS-A-BT- 2
unit
4
6
8
19C
B-AL -7.5K
reactor
-1 1K
-18.5K
-30K
-37K
Zontac- kcording to
tor
power supply unit
Replacement
Remarks
time
The fan life will differ
5 years
according to the
usage conditions.
* The additional
cooling fans must
be prepared by the
machine maker.
(Refer to the
specifications)
Maker
MELCO
TECHNO-
YFB
power supply unit
Mitsubishi
1
7 years
Electric
(only
absolute
position detection system)
MitsubishiAccordingto
When broken
Electric
the
system
configuration
Electric
the
system
configuration
Electric
the
system
configuration
1-23
When broken
Nhen broken
The life will differ

according to the
sage conditions.
As a high frequency chopper current thatis PWM controlled flows to the AC servo/spindle, the leakage
current will be larger than a motor run with a commercial
power supply. Select the leakage breaker
according to the following explanation and securely ground both the amplifier and motor.
1
u, v, w
1 1 1
111
MDS spindle
system
servo
t
111
111
RST
/ I /
111
200/230VAC +
a
Motor
'I
u3,
v3,
Inverter 2
w3
I11
111
I
I
I
I
I
I
I
I
Machine power distribution

box
The commercial frequency compositionof the leakage current for theMELDAS MDS-A Series spindle
and servo system is approximately 6mA for one spindle axis and
1mA for oneservo axis. However, when
selecting the leakage breaker, differences in the motor power line length, distance with the grounding
and motor size, etc., must be considered, and should be calculated
as a max. of 15mA per spindle axis
and 2mA per servo axis.
Furthermore, if other inverter equipment
is connected to the same power line, the leakage current for that
so select and install the leakage breaker
in the position marked
equipment must also be considered, and
@ above.
Select a leakage breaker (for inverters) that removes the high frequency elements with a filter, and that
detects only the leakage current within the commercial frequency range (approx.
50 to 60Hz).
is used, the breaker may
If a leakage breaker that is too sensitive towards the high frequency elements
malfunction.
Note) There is one spindle axis and three servo axes in theMDS Series, and if the total of the leakage
current from the equipment on the same power line is 7mA, select a leakage so
breaker
that the
following calculated value is within the rated non-operative sensitivity current.
15mA + 2mA X 3 + 7mA = 28mA
When using a leakage tester to investigate the cause of leakage breaker malfunction, etc., selec
one thatis not affected easily by the high frequency and which has a measurement
of 50range
to
60Hz.
Example) LC-30F manufactured by Soko Denki
Note) Always ground the machine with class3 grounding for safety purposes.
6. Noise Filter
6. Noise Filter
(1) Selection
If radio noise needs to be reduced, select one of the following noise filters according to the type of
power supply unit being used.
~~~~
MDS-A-CVMDS-B-CV37
55
77
110
150.185
220,260,300
I
I
~~
~~
Noise filter type

(Tohoku Kinzoku)
LF-330
LF-340
I
LF-350
I
LF-360
I
LF-380K
parallel
I inLF-380K
filters
Two
~~
I
I
I
I
1 parallel
LF-380K
in
Twofilters
MDS-B-CV-370
(2) Noise filter installation position

Insert the noise filter atthe unit's input.
Power distribution panel
NFB
1Power
Powersupply
(MDS-A-CV)
supply
!-i
i
i
*Connect to the
transformer input
for the power units
used by the
transformer.
(3) Specifications
~
Rated
voltage
AC
DC (V)
Part
name
I
I
I
330
340
350
360
380K
200v
I
I
Test voltageAC (V)

between case
terminals for one
minute
Rated
current
AC
DC (A)
30A
40A
50A
I
I
200V
200V
200V
60A
2OOV
80A
1500
1500
1500
1500
2000
1-25
~~~
Insulation
resistance
(MW)
SOOVDC
Leakage
current
(mA)
250V 6OHz
Working
temperature
range
("C)
-20 to +55
-20 to +45
6. Noise Filter
(4) Shape and dimensions
LF-300 Series
4-4.5
LF-330
160
-~
A
180
B
170
200
C
60
29
60
30
F
135
220
220
320
E
120
200
200
~
300
G
150
240
240
H
35
40
340
50
I
65
80
80
I00
(mm)
40
LF-K Series
H
-
Name
LF-380K
Terminal
plate
M6
kFi
400
670 TE-K22
1-26
380
560500
170
6.50
9X6
11. MDS-A-CV
MDS-B-CV
MDS-A-CR
Power Supply Section
1. Troubleshooting
1 Troubleshooting
1.I Status display
WARNING
1. Do not touch the switches with

wet hands. Failure to observe this could lead to electric shocks.
3. Do not open the front cover whole the power
ON
isor during operation. Failureto observe this
/I\
CAUTION
1. Always check the parameters before starting. Depending on the machine, unforeseen
operation could take place.

2. Do not touch the sew0 amplifier fins, regenerative resistor
or servomotor, etc., whilethe power
is turnedON or immediately after turning the power OFF. Some parts are heated to high
temperatures, and touching these could lead to burns.
The power supply state is displayed on the 7-segmentLED on the top of the power supply. When an
alarm occurs,the alarmNo. will display on 7-segment LED on the servo/spindle drive connected with the
communication cable(CN4) and on theNC diagnosis screen.
(1) Alarm display on NC diagnosis screen
Alarm displaywith 7-segment LED on drive unit

If the sewo/spindle alarms#60 to #7F display on the diagnosis screen, a power supply alarm has
occurred. The power supply alarm will display as the alarm for the axis connected to the power
supply communication cable (CN4). At the same time, the same alarm
No. will display on the
spindle/sento drive unit's 7-segment
LED. An example is shown below.
The power supply 1 alarm is
displayed as the Z axis alarm
The power supply 2 alarm is

displayed as the spindle alarm
[ALARM MESSAGE]
t N C ALARM>
SERVO ALARM 6A Z
SERVO ALARM 67 S
[SERVO MONITOR]
ALARM
E7
6A
[SPINDLE MONITOR]
ALARM
I1 - 1
67
1. Troubleshooting
NC
Power supply 1
Spindle
Power supply 2
-El
I
Pawer supply 1 alarm

is displayed
b
C
d
: Flicker
I ReadyOFFFrom2OOVAC(24VDC)ONtorelease
Pawer supply 2 alarm
of emergencystop.
Servo OFF Displayed for approx. 1 see. after emergency stop is released and then
changes to d display.
Servo ON Indicates that emergency stop is released and operation
Alarm or warning has occurred
: Alarm display codeuhis display code differs from the alarm

No.)
I1 - 2
is possible.
I.Troubleshootinn
E r Idr&
Alarm display model

A-CV
63
6 4 1
Meaning
B-CV ICl-CVl A-CR
Detection timing
nstantaneous
stop
(24VDC)
Constantly
after
power
is
turned ON
PR
'over
module
overcurrent
Constantly
after
power
is turned ON
PR
-requency
error
Constantly
after
power
is turned ON
PR
ON
PR
Auxiliary
regeneration
error
Constantly
after
power
turned
is
Jot used
iushWhen
error
ready
relay
OFF
Jot used
OFF
ready
When
phase
3pen
Constantly
Natch
dog
power
after
ready
ready ON
tumed
is
OFF
ready
When
3round
fault
OFF
ready
PR
ON
PR
ON
ready ON
PR
During
:ontactor melt
PR
OFF readyDuring melt

iush relay
PR
circuit
dain
error
When
ready
OFF
ready ON
'arameter
When
error
NC power is turned ON
PR
PR
Vlemory
Immediately
errorturned
power
after
is
ON
VD converter
error/power
Immediately
after
power
;upply
OWconstantly error
Instantaneous stop/extemal
emergency stop
76
77
E8
E9
E
E6
0 error
AR
is turned
AR
NR
During ready ON
Over-regeneration
Constantly
turned
power
after
is
75
AR
ON
PR
RegenerativeresistoroverheatConstantlyafterpower
is turned ON
PR
Overvoltage
Constantly
power
after
is turned ON
NR
External emergency stop

settina
Auxiliary regeneration
When NC power is turned ON
Constantly after power is turned ON
I -
AR
frequency over
ready
During
warning
Instantaneous
stop
External
emergency
stop
input
When
ready
Over-regeneration
During
warning
ON
NC power is turned ON
ON
[Alarm No.] Alarm No. displayed on the drive unit connected to the power supply unit
[LED display] LED displayed on power supply unit
[Release]AR
: Released whenpowersupplyunitpower is turned ON again.
PR : Released when NC power is turned ON again.
NR: Released with NC reset key.
I1 - 3
1. Troubleshooting
1.2 Troubleshooting per power supply alarm
CAUTION
When an alarm occurs, remove the cause of the alarm, confirm that an operation signal
is not
being input, and secure the safety. Then reset the alarm to resume operation.
When an alarm occurs
in the spindle amplifier, the base will be off
shut
and the motorwill coastto a stop.
Turn the powerOFF with an external sequence.
(I)Alarm No.
[Meaning]
[Detection]
Instantaneous
stop
The 24VDC voltage connected to the CN22 connector
has dropped.
I.Troubleshooting
(2) Alarm No.
[Meaning]
[Detection]
Oneration
unit
1
-~~~~~
C1-CV A-CR
B-CV
This is a overcurrent in the power module in the power A-CV
0
0
0
supplyConstantly after power is turned ON
module
overcurrent
Power
~~
~~
Investigation results
Investigation item
Remedy
Zonfirm the operation state at Occurs each time servo turns
ON Replace the unit.
xxurrence and repeatability
after turning2OOVAC ON.
Occurs often during servo ON Perform investigation item3.
Occurs when motor decelerates
Occurs when continuous
Perform investigation item2.
operation for long time is
performed. Unit is hot.
Lower motor load and operation
Investigate the load state,
The total of all motors' loads
frequency.
of each
exceeds power supply rated start/stop
frequency
motor.
caDacitv.
Perform investiaation item3.
] Not exceeded.
Investigate whether the power
s pply is normal.
1) Is rated power supply
Power capacity is insufficient.
Increase the power supply
capacity secured?
caDacitv.
2) Confirm that the poweris
Power is less than 17OV.
170V or more even during
capacity.
motor acceleration/
Power is higher than 17OV.
Perform item 3).
deceleration.
3) Observe the power voltage 1. Distortion in voltage waveform. Eliminate the waveform distortion.
with a synchroscope.
1. Increase the power capacity or
power cable size.
( A l s o during acceleration/
deceleration)
2. Improve the other
semiconductor units where
waveform distortion is
occurring.
(Add anAC reactor.)
2. When there is a partial drop.
~~~
~~
~~
3. Other waveform or frequency

error.
Measure thevoltage be6&enp
The voltage difference between Improve the power phase
R-S, S-T, T-R with a tester.
each wire is1OV or more.

None of the above apply.
balance.
Grounding is incomplete.
Alarm occurs easily when a
certain device operates.
No problem found.
Correctly ground.
Perform the noise measures for
the device on the left.
Replace the unit.
Investigate the installation

environment.
Is the grounding correct?
Is there any noise generating
equipment in the surrounding
area?
I1 - 5
I.Troubleshooting
(3) Alarm No.
[Meaning]
[Detection]
Frequency
error
The power frequency is not within the specifications
range.
Remedy
lnvestiaation item
is turned Perform investigation item2.
Confirm the operation state at Occurs each time power
Occurrence and repeatability
ON.
Occurs periodically regardless of
operation state.
Performjnvestigation item 3.
Occurs only when motor
accelerates/decelerates.
Review the power facilities.
Measure power voltage when The frequency is deviated from
50Ha3Y0 or 60Hzlt3Y0.
operation is normal
The frequency may deviate from
50H~i3%
or 60H2&3% dueto
fluctuation in the frequency.
There is a partial dropin the
Take measures for the power unit
voltage waveform.
or device causing the problem.
(Add an AC reactor, etc.)
The frequency is 50H*3% or
Replace the unit.
60Ha3%.
No problem found.
The frequency fluctuation during Review the power facilities.
Measure the power voltage
acceleration/decelerationis
while the motor is
accelerating/decelerating.
great.
There is a partialdrop in the
Take measures for the power unit
or device causing the problem.
voltage waveform during
(Add an AC reactor, etc.)
deceleration.
No problem found.
The grounding is incomplete.
Correctly ground.
environment.
Replace the unit.
No problem found.
~~~
1. Troubleshooting
(4) Alarm No.

[Meaning]
[Detection]
Auxiliary
regeneration
error
The auxiliary regeneration transistor in the power
supply is continuously ON.
Operation unit
A-CV I B-CV ICl-CVI A-CR
l o l o l
l o 1
Investigation item
lnvestiqation results
Remedy
Dirt on the regenerative
Take measures so that cutting oil
Cutting oil or oil mist is adhered on
resistance urriton the unit rear. the regenerative resistance unit. or dust does not get on the fins on
the unit rear, and perform
investigation item2.
Not dirty.
Replace the unit.
Confirm the conductivity
of
is a conductivity.
Replace the unit. There
the terminal block (P, N, R, S,
Clean the resistor or fin and take Resistance
T) and the resistor surface
with
measures so that oil and dust do
a tester.
not get on them.If the alarm
occurs again, replace the unit.
(5) Alarm No.

[Meaning]
[Detection]
1
The rush resistance short circuit relay in the power

ON.
supply does not turn
When ready OFF
ready ON
Investigation item
Investigate the repeatability
environment.
Is the groundingcorrect?
area?
(6) Alarm No.@

[Meaning]
[Detection]
Rush
relay
error
Occurs every readyON
Occurs periodically
Remedy
Replace the unit.
No problem found.
Correctly ground.
Replace the unit.
Openphase
One phase of input 30AC2OOV is not connected.

When ready OFF
ready ON
voltage with a tester.
There is a phase with no voltage.
All phases arenormal.
Oneration
unit
A-CV B-CV Cl-CV A-CR
~
Remedy
Supply the correct power.
Perform investigation items3 and

4 for alarm 71 Instantaneous stOD.
I1 - 7
I.Troubleshooting
(7) Alarm No.

[Meaning]
[Detection]
Watch
dog
The power supply software process did not end within
the designated time.
Investigation item
environment.
area?
(8) Alarm No.
[Meaning]
[Detection]
t
IL
Occurs every readyON
Occurs periodically
Oneration
unit
I
I
~~~.
~
Remedy
Replace the unit.
Correctly ground.
theindevice
on the left.
certain device operates. equipment
the surrounding
Replace
the
unit.
No problem found.
Ground
fault
Motor ground fault
When ready OFF 4 ready ON
Investigation item
Measure the insulation
1OOkQ or less
between theU W terminals of
all motors and the grounding q o o k ~
or more
with a megger tester.
Is motor or cable covered with Oil isfound.
oil?
Perform the insulation

measurement again.
Oil is not found.

1Mi2 or less
1Ma or more
'
'
'
Remedy
Motor defect or cable ground fault.
Replace motor and cable.
Take measuresso that oil does
not come in contact.
Clean the motor's cannon
connector and inside the terminal
box.
If the error occurs again, perform
Replace motor or cable.
Replace the unit.
I.Troubleshooting
(9) Alarm No.
[Meaning]
[Detection]
Contactor
melt
The externally connected contactor is on even during
ready OFF.
Duringready OFF
Contactor is not externally
installed.
Connector is externally installted.
Alarm 6A occurs.
Alarm 6A does not occur.
Investigation item
Is the contactor externally
installed?
Has the contactor melted?

Disconnect the contactor
exciting wire and start up.
Has an error occurred on theError has occurred.
driver side (power module
error, etc.) before alarm6A
Error has not occurred.
Occurred?
Is the contactor exciting wiring
correctly passed though the
MC1-RO terminal?
I
Remedy
Set the power supply rotary switch
(SWI1 to 1.
Remove driver side error cause
and then replace contactor.
Replace contactor.
Wire as shown below. Wiring is not correct.
II
II
RO
EMG
Switch, etc.
Wiring is correct.
( I O ) Alarm No.
[Meaning]
[Detection]
Rush
relay
melt
The rush resistance short circuit relay in the power

supply is ON.
Duringready OFF
~~
Replace the unit.
Oneration
unit
I
~~~
~~
investigation item
Investigate the repeatability.
Remedy
Occurs each time power is turned
ON.
2
Occurs periodically.

environment.
Correctly ground.

area?
No problem found.
3 Has an error occurred on the Error has occurred.
driver side (power module
error, etc.) before alarm6B
occurred?
I1 - 9
Perform the noisemeasures for
the device o n the left.
Replace the unit.

Remove driver side error cause
and then replace power supply
unit.
Replace the unit. Error has not occurred.
I.Troubleshooting
(1I)
Alarm No.
[Meaning]
[Detection]
Maincircuiterror
Charging to the main circuit is not normal.

When ready OFF
ready ON
ODeration
unit
Remedy
lnvestiaation item
for Replace the unit.
Observe the CHARGE lamp The CHARGE lamp remains lit
lighting when the alarm occurs. a short time.
The CHARGE lamp lights
momentarily but soon the alarm
occurs, and when the contactor
turns OFF, it goes
out
immediately.
Perform investigation item2, and
The CHARGE lamp does not light.
then replace the unit.
Disconnect thePN terminal
(1) Error on the power supply
Replace the unit.
block wiring and confirm the
side.
following resistance values with(2) Error on the driver side
Review thePN wiring and
a tester.
investigate the drive unit.
Replace the unit.
Both (1) and (2) are normal.
Driver
Driver
Power
supply
Defect
Short circuit or infinite
supply side
Short circuit or several 1 0 0 0

Short circuit or infinite
Disconnect only thePN wiring

on the power supply.
Measure the positions(1) and
(2) with a tester.
Short circuit or several 1 OOR
11- 10
I
I
I.Troubleshootinn
(I
2)
Alarm No.
[Meaning]
[Detection]
Parameter
error
The power supply unit (CR) capacity and the
regenerative resistance type (rtyp) set in the
parameter PRYP are not set to an adequate
combination.
When NC power is turned ON
Investigation item
Remedy
Change the setting to the

following combinations.
1 Confirm the parametersof the
drive unit connected to the

power supply unit.
Spindle : SPO41 (PlYP)
Servo : SV036 (PTYP)
Servo/spindle parameter :
svo36 sP041 PlYP

F E D C B A 9 8 7 6 5 4 3 2 1 0
wl
lptypl Power supply type
External regenerative resistancetype

(Set type from following table)
(Set type from following table)
89
Power supply type

CR-10
CR- 51
CR-22
CR-37
CR-55
CR-75
CR-90
External regenerative resistance and power supply

(A-CR) compatibility table
11-11
PtyP
81
82
83
1. Troubles hooting
(13) Alarm No.
Memory
error
[Meaning]
[Detection]
Error in the memory circuit in the power supply

Immediately after power is turned ON
Investigation item
1
environment.
area?
(14) Alarm No.
16FJ
[Meaning]
[Detection]
Remedy
the the
unit.repeatability.
Occurs each time power is turnedReplace
Investigate
ON.
No problem found.
Correctly ground.
Replace the unit.
AID converter error/power supply error
Error in the N D converter in the power supply, or the

driver detected an error in the power supply
Immediately after power is turned ON ( N D converter
error)/constantly (power supply error)
Remedy
results
Investigation
item
lnvestigation
Check
power
the
supply
7segment LED display: -
F is flickering.
Other alarm codeis flickering.

0 is displayed.
F is displayed.
8 is displayed.
b, c, d are displayed.
Other display
Investigate
rotary
theswitch
Setting
setting.
A/D converter
error.
Perform same remedies as for
alarm 6E memory error.
Refer to each alarm section.
Refer to alarm68 watch dog
alarm.
Refer to alarm 68 watch dog
alarm.
isReplace
01.orunit.
the
Setting is not 0 or
Correctly
1.
set
the
rotary
switch.
mistaken.
wiring
is
driver
Replace
The
Check
cable.
the
the
communicationcablewiring.There
replacing
Try
driver
the
communication cable.
is noshield.
wiring
The
is
OK.
OK replacement.
after
Cable
defect.
NG
even
after
replacement.
Replace
the
unit.
Perform
investigation
item
4.
I.Troubleshooting
(15) Alarm No.
1711
weaning]
Instantaneous stop/external emergency stop
Theexternallyinstalledcontactoris OFF.
An instantaneous stop exceeding 25ms occurred.
Duringready ON
[Detection]
Investigation item
Is the externally installed
contactor OFF due to
emergency stop, etc.?
Check the sequence.
1731
weaning]
[Detection]
~~
, o
Perform investigation item1

again. If there is no error, perform
Occurs sometimes during

operation (not-regulated).
The wiring or sequence is
Is the RST wiring correct?
incorrect.
Is the contactor wiring
No error.
sequence correct?
Observe the power waveform Instantaneous power failure or
voltage drop occur often.
No error.
(16) Alarm No.
ODeration
unit
B-CV Cl-CV
A-CV A-CR
Remedy
The power supply operates
normally. Check the machine
sequence. When directly turning
OFF the contactor with the
emergency stop button, etc., and
the NC emergency stop is applied
simultaneously with the contactor
OFF, emergency stop will occur
instead of alarm.
Contactor isOFF.
Contactor is notOFF.
Occurs constantly during ready
ON.
Occurs with certain operation.
Occurrence state.
Repair the items noted on the left.

Replace the unit.
Over-regeneration
Theregenerativeresistor'sloadexceededthe
tolerable value.
ODeration
unit
I
A-CV B-CV C1-CV A-CR
Remedy
Check for the effect of power
The regeneration load display
fluctuation, grounding connection
increases when the poweris
state and the regenerative load
and noise. If there is no
turned ON and the motor is
displayed onthe monitor
abnormality, replace the unit.
screen? Confirm by changing rotated.
A-CR : Perform investigation
the operation mode.
The regeneration load display
item 2.
increases each time the motor
B-CV . Perform investigation
decelerates, and an alarm
item 3.
occurs.
Theregenerationloaddisplay
If thereisnoproblemafter
increaseseachtimethemotorperforminginvestigationitem
2,
decelerates, but an alarm does
ease the operation mode.
the
when
occur
not
is
I mode
1
I
Investigation item
1 What is the alarm Occurrence
operation
eased.
I I
I I
I1 - 13
-
1. Troubleshooting
Investigation item
Remedy
The setting is incorrect. (Refer to Set to the correct setting, and
Confirm that the external
regenerative resistance type the parameter settings for alarm confirm again.
"6D".
OL set in the parameter (PTYP) of
the drive unit connected to the The setting is correct.
z power supply unitis correct.
0 Confirm that the rotary switch
cv is set to"0'.
* This maybe set to "2" for
- special specifications.
3 Confirm whether the operation
is correct after performing
investigation item3 for alarm
"75*,
and that the regenerative
resistance value, etc., is
correct.
I
I
)
.
I I
(17) Alarm No.
1741
[Meaning]
-~
[Detection]
Regenerative resistance overheat
Theexternalregenerativeresistancethermalrelay
has functioned.
Investigation item
Confirm whether the resistor
has overheated.
Note) Do not touch the
resistor or case
directly. It ishot and
can cause burns.
Confirm the alarm history.
The over-regeneration
warning or over-regeneration
alarm has occurred.
Is the resistor installation
correct?
Confirm theCN22 (B)
connector pins 1 and 2.
Confirm whether there is a
short circuit caused by the
lnvestiaation results
The unitis hot.
The unitis not hot.
~~
srform investigation
item
3.
The alarm has occurred.

there is no abnormality, ease the
The alarm has not occurred.
The wire is cut.

There is no conductivity in the
resistor's terminal relay.
The wire is correct.
I1 - 14
"..
~~~
resistor's terminal or wire.
yl_
regenerative resistor.
Install in a well-ventilated
place.
Cool with a fan, etc.
Replace with correct wiring.
Replace the resistor.
Replace the unit.
I.Troubleshooting
(18) Alarm No.

[Meaning]
[Detection]
Overvoltage
The voltagebetweenPNexceeded410V
ODeration
unit
I
A-CV 6-CV C1-CV A-CR
0
~
Investigation item
Remedy
What state did the alarm occurOccurs each time the motor
in?
decelerates.
I
Occurs always during a certain Perform investigation item3.
deceleration mode.
Look at the alarm history on the
EO is output right before the
power supply diagnosis screen.overvoltage.
(Over-regeneration warning)
Others
Observe the regeneration load
Decrease the simultaneous Regeneration load
of the axis where the alarm when several axes decelerate
deceleration frequency.
occurred on the servo/spindle simultaneously.
monitor screen.
Other than the above.
Investigate whether the power
s DDIV
is normal.
I) Is rated p e r supply
Power capacity is insufficient.
Increase the powersupplycapacity.
capacity secured?
Power isless than 17OV.
2) Confirm that the poweris
capacity.
170V or more even during
motor acceleration/
Perform item 3).
Power is higher than 17OV.
deceleration.
3) Observe the power voltage 1. Distorhon in voltage waveform. Eliminate the waveform distortion.
I.
Increase the power capacity or
( A l s o during acceleration/
power cable size.
2. Improve the other
deceleration)
semiconductor units where
waveform distortion is
occurring.
2. When there is a partial drop.
(Add an AC reactor.)
~
3. Other waveform or frequency

error.
Measure the voltage between The voltage difference between
R S . S-T. T-R with a tester.
each wireis 1OV or more.
None of the above
amlv.
Observe the power waveform Instantaneous power failure or
voltage drops occur often.
No error.
environment.
Is there any noise generating Alarm occurs easily when a
equipment in the surrounding certain device operates.
area?
No problem found.
I1 - 15
Improve the power phase

balance.
Perform investigation item5 .

Correctly ground.
the device on theleft.
Replace the unit.
1. Troubleshooting
(19) Alarm No. @ External emergency stop setting error
[Meaning]
[Detection]
1771
[Meaning]
[Detection]
ODeration
unit
Therotaryswitchsettingandparameter(PTYP)
setting do not match.
Investiaation item
Confirm the rotary switch
When not using external
setting and the parameter
emergency stop
1. The rotary switch is set to
4 or
(PTYP) of the drive unit
connected to the power supply 5.
unit.
2.The parameter (PTYP)is set
to **40 to **79.
When using external emergency
stop
1. The rotary switch is set
to 0 or
1.
2. The parameter (PTYP)is set
to **oo to **39.
The combination is correct.
(20)Alarm No.
Remedy
1. Set the rotary switch to0 or 1.
2. Set the parameter (PTYP) to
**oo to **39.
1. Set the rotary switch to

4 or 5.
2. Set the parameter (PTYP) to

**40 to **79.
Replace the unit.
Power module overheat
Overheating of the power module (IPM) in the power

supply was detected.
Investigation item
Investigate the heat radiating
environment
1) Rotation of fan on rear of The fanis not rotating correctly.
unit
2) Contamination of radiating Remarkable amounts of cutting
fins on rear of unit
oil or dust are adhered on the
radiating fins.
3) Measurement of unit
55C is exceeded.
ambient temperature
The groundingis incomplete.
environment.
Alarms occur easily when a
Are there any noise generatingNo particular problem.
devices in the periphery?
I1 - 16
Remedy
Replace the Take measures

fan
to prevent cutting
Clean the fins oil or dust from
contacting the
fins.
Consider ventilatingor cooling
measures for the panel.
Correctly ground.
Take noise measuresfor the
device on the left.
Replace the unit.
1. Troubleshooting
1.3 Power supply warnings

The power supply warnings are not displayed on the servo/spindle monitor screen. The warning
will be
displayed on the power supply's 7-segmentLED and in the alarm historyon the power supply diagnosis
screen.
Operation can be continued after the warning, but
it does indicate that thereis a factor for an alarm.
(1) AlarmhistorydisplayAuxiliaryregenerationfrequency
[Meaning]
[Detection]
1
(2) Alarm
history
display
Instantaneous
stop
warning
[Detection]
1
E l
Thisindicatesthattheinstantaneousregeneration
energy is large, and regeneration was not possible
only with the power supply regeneration. Due to this,
regeneration at the auxiliary regeneration's
performance limit occurred. When this warning occurs,
the auxiliary regeneration will not function,
so this
could lead to an overvoltage alarm.
Duringready ON
Investigation item
Perform inspectionitems 3 and
following in alarm 75
overvoltage.
[Meaning]
over LED display
Remedy
LED display
An abnormal instantaneous stop occurredfor 25ms or

more. An alarm did not occur because the main circuit
voltage did not drop. This may cause an
instantaneous stop alarm, overvoltage alarm
or power
module error.
Duringready ON
Investigation item
Perform inspection items3 and
following in alarm 71
instantaneous stop.
Remedy
11-17
,
... . .j.. .
1. Troubleshooting
(3) AlarmhistorydisplayExternalemergencystopinput
[Meaning]
[Detection]
LED display
The external emergency stop signal was input.

24V is not applied
on the CN23 connector.
Investigation item
When not using external
[4j
I
Oneration
unit
Remedy
Set to invalid. Refer to
The external emergency stop
is
investigation item 1 of alarm 76.
set to valid. emergency stop Investigate
the rotary switch and

parameter (PTYP).
When using external
Replace the unit.

24V is applied on the CN23
connector. emergency stop
Investigate the CN23 Perform
investigation
itemon the CN23
24V
is not applied
1
connector
voltage.
connector.
Correctly wire.
0Investigate whether the The wireis broken or breaks
CN23 connectororcable is sometimes.
broken.
Replace the switch.
The contact is defective or
is
@ Investigate the external
emergency stop switch periodically defective.
I contact.
I
I
3.
(4) Alarm
history
[Meaning]
[Detection]
display
Over-regeneration LED display
11-1
80% of the over-regeneration alarm level was reached.

Duringready ON
Investigation item
Perform the investigation
items for alarm73 overregeneration.
Remedy
111. MDS-A-VX
MDS-B-VX
Servo System Section
1. MDS-C1-Vl/V2 Servo Drive Unit
1. MDS-ClmV1/V2Servo Drive Unit

1.I Points changed from B Series
1.I-1 Compatible detectors and compatible motors
(1) Compatibledetectors
Note that some detectors are not compatible with the C1 Series.
0: Connectable, x: Not connectable
Detector model
Detector type
MDS-C1MDS-8MDS-BV1N2 Series
Series V1N2 Series
_ _ V14N24
.~
~
ABZ
(+ low-speed serial)
High-speed serial
Motor end
detector
Motor built-in
encoder
OHE25K-6, OHE25K-85,
OHA25K-6, OHA25K-85
OSEl04.OSE104S. OSEl04S1.
OSE104S2
OSE105,OSE105S, OSElO5S1,
OSA105S2
OBA13.OSAl4.OBA17
I High-speedserial
I
IABZ
Linear
scale
High-speed serial
OSE104-ET, OSAl04-ET
OSA1054ET. OSElO5-ET
Optical scale, magnetic scale,MP scale
AT41(Mitsutoyo)
FME type, FLE type (Futaba Denshi)
AT342 (Mitsutotyo) Resolution O.*m
LC191 M (Heidenhain) Resolution
0. l u m
AT343 (Mitsutoyo) Resolution 0.05pm
Heidenhain analog output scale
(LF Series, LS Series)
+ MDS-B-HR (Scale interface unit)
~~
I o l x
OHE2500
OHE-25K-ET, OHA-25K-ET
detector
l x
0
0
0
~~
(2) Compatiblemotors
: (INC specification)
(ABS specification)
2) HC R motor
(ABS specification)
3) HANmotor
(ABS specification)
4) HA L motor
(ABS specification)
5) HA-LH S1 motor
(ABS specification)
: (ABS specification)
6 ) HA-FFmotor
: (ABS specification)
7) HC-MFmotor
8 ) HA compact motor : (INC specification)
HA-FE**
(ABS specification)
HA-FH**
1) HCmotor
HC***-E42/E51,
HC***-A42/A51
HC***R-E42/E51f
HC***R-A42/A51
HA***N/INC high-speed serial encoder,
HA***N/ABS high-speed serial encoder
HA***L/INC high-speed serial encoder,
HA***L/ABS high-speed serial encoder
HA-LH**Sl/INC high-speed serial encoder,
HA-LH**Sl/ABS high-speedserial encoder
HA-FF***
HC-MF***
HA053NC, 13NC/INC high-speed serial encoder,
HA053NC, 13NC/ABS high-speed serial encoder,
INC high-speed serial encoder= OSE104/S/Sl, OSE105/S/S1

ABS high-speed serial encoder= OSA104/S/Sl, OSA105/S/Sl
111 - 1
1. MDS-Cl-VlN2 Servo Drive Unit
1.1-2 2-system compliance (standard amplifier (MDS0B-V1/V2) mode and high-gain

amplifier (MDS-B-V14/V24) mode)
'
(1) Outline
With the C1 Series, control can be carried out in the standard amplifier (MDS-B-V1N2) mode and
high-gain amplifier (MDS-B-Vl4N24) mode. This allows the amplifier to be changed from the
standard amplifier (MDS-B-V1N2) orfromthehigh-gainamplifier
(MDS-B-Vl4N24) with the
same parameters.
When the standard amplifier is replaced with the high-gain amplifier, the amplifieris recognized
automatically by the status of the servo parameters set with the machine.
CAUTION
When the control mode has been changed to the high-gain amplifier
(MDS-B-Vl4N24) mode
after remounting from the standard amplifier (MDS-B-V1/V2), the parameters must be changed
for the high-gain amplifier and
the servo parameters mustbe adjusted.
(2) Compdtible software version
The 2-system compatible software

is compatible from Version A1 (BND-582W000-Al).
* Version A0 is not compatible with the standard amplifier mode. It is compatible only with the
high-gain amplifier mode.
(3) Judging changeover of control mode
Whether to start the servo amplifier in the standard amplifier compatible mode or the high-gain
amplifier compatible modeis judged by the servo parameters
SVOO9 to SVO12 and SV033 setting
values set in the machine.
Setting in which not even
one of the following
Servo
svm
'0 Sv012
parameters
svO33 (SSF2)/bii8
svO33 ( S S F 2 ) b i i
SVOO9 = 4096 or more, conditions is satisfied.

SVOlO = 4096 or more,
s v o 1 1 = 768 or more, and S V m = 4096 or more*
~ ~ 0 =1768
2 or more.
svol
SV010= =
768 or mo18,
or more,
and
SVOl2 = 768 or more
0
0
Control mode
High-gain mode
Standard mode
svo1o=*
svo1o=*
svoo9=*
svoo9=*
svol1=*
svo12=*
svo11=*
SVOl2=*
svol1=*
svo12=*
0
1
1
1
svoo9=*
Standard
svo1o=*
High-gain
Highgain
mode modemode
CAUTION
The actual mode is changed between the standard amplifier mode and high-gain amplifier mode
when the 200V poweris turned ON. Thus, if the above servo parameters are changed, the alarm
"7F"will occur, and the resetting
of the power will be requested. Alarm"7F"may also occur when
the poweris turned ON for thefirst time after the machine is installed.
If alarm "7F"occurs, turn the
power ON again. The alarm"7F"will not occur after the second and subsequent power
ON unless
the above servo parametersare set.
(4) Display of servo monitor type for highgain mode and standard amplifier mode
(Servo Monitor screen)

Whether the system is running
in the high-gain mode or standard amplifier mode can be confirmed
with the type displayed on
the Servo Monitor screen.
~~
~~~~
~~
Unit type
MDS-C1-VI -000
For standard amplifier mode
MDS-C1- V 2 - 0 0 0 0
MDS-C1-V145S
MDS-C1 -V2-7070S
MDS-C1 -V2-351
OS
MDS-C1 -V2-3520S
c1v2soooo
c 1Vsl4S
c1v2s7s7s
C1 V2s3510
c1v2s3520
c1v1sooo
I11 - 2
For high gain mode

ClV1-000
ClV2-0000
c1v 1 4 s
ClV2-7S7S
ClV2-3510
C1 V2-3520
2. Adjustment Procedure
2.1 Initial adjustment
/1\
CAUTION
Do not make remarkable adjustments and changes of the parameters as the operation could
become unstable.
2.1 .I Confirmation of parameters

Confirm thesew0 parameters once again after installing the machine and checking the wiring, etc.
(1) Confirmthatthe
sew0 specificationparameterdata(machinespecifications,servosystem
specifications) are correct.
Refer to the SERVO MONITOR screen (3/3)[SERVO DIAGNOSIS] for the servo system, and
confirm that the amplifier
type (UNIT TYP), control method(CONTROL), motor end detector(MOT
DT), machine end detector (MAC
DT) and motor(MOTOR) are correct.
SERVO MONITOR (SERVODIAGNOSIS) Screen
DIAGNOSIS][SERVO
<x>
3/3
<Y>
<2>
UNIT TYP
UNIT NO
S W VER
CONTROL
MOT DT
MAC DT
MOTOR
WORK TIME
ALM HlST
(2) Confirm that the standard parameters

for the specifications motor areset.
Refer to the specificationsfor the standard parametersfor each motor type.
I11 - 3
. .,
~
2.1.2 Adjustment of optimum accelerationldeceleration time constant

The rapid traverse acceleration/deceleration time constants are adjusted according
settings as theydiffer according to the load inertia, friction and motor capacity.
to the following
(1) Set the acceleration/deceleration time constant initial value. The basic setting equation
below.
Ts = 1000 (2nN/60) (J, + JL) / (0.8 Tm
Ts
N
J,
JL
, ,T
TF
- TF)
is shown
(ms)
Acceleration/deceleration timeconstant (rns)

Motor speed duringraFidtraverse(rpm)
Motorinertia(kg0crn.s
)
Load
inertia (kg*cms2)
: Maximum output torque for amplifier (during motor combination) (kgocm)
: Motor shaft conversion load torque during rapid traverse (kgocm)
:
:
:
:
(2) The rapid traverseacceleration/decelerationmode is selected and the time constants set
in the NC
device parameter axis specifications screen.
(3) After reciprocating with rapid traverse for about five times, adjustacceleration/deceleration
the
time
constant so that the MAX current 1 value on the servo monitor screen(1/3)is within the optimum
maximum current value range givenin Table 3.1.
Note)
If the maximum current value exceeds the optimum maximum current value given in
Table 3.1, the acce'leration/decelerationconstant mustbe increased.
The max. current1 indicates the maximum value
(stall current conversionYO(absolute
value)) from whenthe NC power is tumed ON, so the NC power mustbe turned OFF
when repeating rapid traverse operation to confirm the current.
The max. current 2 indicates the absolute valuethe
of max. current in
2 sec.intervals, so
the powerdoes not need tobe turned OFF when adjusting while looking at this value.
Motor current
J
l I
Max. current 1
Max. current 2
>
<
2 sec.
Table 3.1 Max. output torque per motor and optimum max. current
Standard
2000rpm
motor
I
Motor
HA40N
OON
HA200N
HA700N
HASOON
243 to
Optimum max.
Tmax
current
to 400 14.2
325 to 365
25.5 HA80N
42.0 HA1 230 to 260
200 to 225
60.0
87.0 HA300N to 200
to 205
120.0
220
153.0
Standard
3000rpm
motor
1
Motor
Tmax
HA053N 355 0.7

1.4
HA13N
2.8
HA23N
5.6
HA33N
HA43N 180
HA83N 185 19.2
HA1 03N 19540.0
to
56.0
HA203N
80.0
HA303N
HA703N
180to
105.0
160
9 HC52
21 8.8
HC52
366 to 323
11.8
21
HC103
16.7
321 to 283
HC102
21.6
317
HC152
35.3
251 to 222
HC153
28.4
to 359
228
HC202
41.7
214
HC203
40.2
to 259
20959.0
HC352
19155.9
HC353
to 237
Tmax
Motor
HA50NL
HAlOONL
HA150NL
HA200NL
HA300NL
HA-LH11K2
1K5
13.0
20.9
31.,.0
32.0
52.0
72.0
158.0
215.0
Optimum max.
current
320 to 365
265 to 300
to 315
175 to 195
175 to 195
145 to 165
HASOONL
180 to 205
195 to 220
HA-LH1
Optimum max.
current
210 to 240
210 to 240
205 to 230
205 to 230
260 to 295 10.2
245 to 275
220 to 245
185 to 210
160 to 180
i
to 249
to 243
to216
Optimum max.
current
HA53NL
HA1 03NL
HA1 53NL
HA203NL
HA303NL
HA503NL
22.5
275
22.8
37.0
60.0
78.0
360 to 410
285 to 320
195 to 220
200 to 230
195 to 225
155 to 175
14.1
2.1.3 Adjustment of speed gain

(1) The speed related gain is adjusted on theservo adjustment parameter screen. The corresponding
items are2.VGNI (SVOOS), 3.VIA (SV008) and4. VIL (SV007).
VIL (SV007) is used only for the closed loop, so the adjustment procedure will be explained
later.
The standard value for the VIA (SV008) speed integrated gain
is 1364, andis set to 1900 when
using the feed fonnrard control or
SHG control in the high precision control mode.
(If the machine system resonance frequency is low and the speed loop gainVGNI (SVOOS)
does not increase, the VIA (SV008) may need to be lowered, but in this case, the other values
above will be the standard values and
do not need tobe adjusted.)
Servo adjustment parameter screen

2/6
[SERVO PARAMI
<x>
<Y>
cc>
<2>
1 PGNZ ( l/SEC)
2 VGN
3 VIA
4 VIL
5 FFC
6 JL
7 FHz(Ht)
8 TOP(%)
0 LYCl(X)
1 0 LUC2(%)
11 O V S l (%I
12 O V S Z ( W )
The VGNl (SVOOS) optimum value and maximum value will change according to the load so
inertia
refer to the following diagram and set the initial
VGNl (SVOOS) value. The following diagram shows
the values when the motor and load are linked,
so the motor may vibrate even with a lower setting
when gears are used, or due to the coupling method
ball screw
and twisting even
if linking is used. In
that case, lower the value to that which
is SO lower than the value where vibration occurs, and reset.
Load inertiascale (load inertialmotor inertia)
Load inertia scale (load inertialmotor inertia)
unitsingle
Motor
<HC**>
500
400
HC202
HC352
-H a 5 2
HC702
HC902
HC203
HC353
HC453
HC703
300
Standard
VGNl
200
\ HC53
100
HClO2
HC152
Load inertia scale (all load inertidmotor inertia)
(2) Perform rapid traverseacceleration/decelerationand confirm the following.

Has the load current on the servo monitor screen fluctuated after stopping? (Changed
by * l o or
more)
Is vibration still felt in the table and cover? (Vibration may also occurtodue
the hydraulic pump,
etc.)
If the above vibration or abnormal sound occurs, lower

VGNl (SVOOS) by 50 at a time. Set the value
as 0.7 times the gain when the abnormality stopped.
The VGNl (SVOOS) is finely adjusted with the servo amplifier's
DA output function. Check the
current stability after
outputting
the
current
command
and
performing
rapid
traverse
acceleratiorVdecelemtion. Set the VGNl (SVOOS) value as0.7times theVGNl (SVOOS) value when
current vibration such as shown below stopped.
Command speed
current
The vibration may occur due to the machine resonance, and if the frequency is known may be
eliminated by settingthe frequency in the machine resonance suppression frequency
FHz (SV038)
without loweringVGNl (SVOOS). If the vibration is eliminated with this setting, raiseVGNl (SV005)
again, and confirm the limit.
If the optional adaptive filter
is mounted, turnON servo parameter"27. SSFl bit F"and the machine
resonance will be eliminated automatically.
I11 - 7
--_
......
2.1.4 Zero point return

(1) Parameter settings
1) Servoparameters
The MDS-A/B Series servo does not require special parameter settings even when the1 shot
type scale is used in the closed loop.
2) NC parameters (zero point return parameters)

Basically, the settings are the same as the M300 Series. However, in the M500 Series, the
4.
grspc (grid space) setting unit is mm, and there
is no limit to the setting amount. (In the M300,
the zero point position may deviate if the servo parameter RNG (equivalent to RNGl in the
MDS-A/B Series) if it is not a divisor.)
(2) Theory of zero point
The basic configuration of zero point return is shown
below.
I) The reference for the zero point position is the last Z phase passed before reaching the dog
OFF stop, and theNC creates the hypothetical grid for each grspc from Zthe
phase.
2) The position stopped at after the distance(L) from the dog OFF position to the next grid+ the
grid shift amount(G28sft) is moved is the zero point.
Motor speed
Z phase
NC hypothetical grid
'I
Dog
Zero point reference

2 phase
I
G28sf t
3
I
(3) Confirmation of zero point return position

Confirm that the zero point position is correct with the cycle (P)
counter
on the servo monitor screen.
Repeat zero point return about five times, and confirm that the cycle counterisvalue
the same after
reaching the zero point.
(Note) After zero point return, the high speed zero point return mode (not usingZ phase) will be
applied from the second return,
so turn OFF the power beforestarting each zeropoint return.
(Dog-type zero point return can be performed without turning the powerOFF each time by
turning ON the automatic dog method or manual dog method in the NC user parameter's
axis parameter.)
2.1.5 Adjustment of absolute position detection

TO confirm the absolute position detection with absolute position deviation, etc., investigation, confirm
the data on the servo monitor's ABSOLUTE POSITION MONITOR screen.
(1) Confirmation of ABSOLUTE POSITION MONITOR screen data
ABSOLUTE POSITION MONITOR Screen
POSITION MONITOR]
DlAGN 2 .
(C)
(X)
2/3
ABS SYS
POF POS
PON POS
MAC POS
Rn
Pn
No.
1
2
3
4
7
8
9
10
11
12
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Display item
ABSSYS
Description
The servo side absolute position detection system is
displayed.
ES : Semi-closed
EC : Ball screw end detection
LS : Absolute position linear scale
The absolute position before the power was turned
OFF last
POF POS (command unit)
is displayed.
The absolute position when the power was turned ON this
PON POS (command unit)
time is displayed.
(Absolute position detected when power is turned ON.)
The coordinate value in the
NC basic machine coordinate
MAC POS (Command unit)
system is displayed.
The detector's multi-rotation counter value (motor .
RO
cumulated speed) registered when the reference point was
set is displayed.
The position in one detector rotation registered when the
PO
reference point was set is displayed.
The absolute position error registered when the reference
EO
point was setis displayed.
The current motor accumulated speed is displayed.
Rn
The current position inone motor rotationis displayed.
Pn
(x division)
The absolute position error when the
NC power is turned
En
OFF is displayed.
ABSn (NC interpolation unit) The current absolute position displayed.
The MP scale offset amount when the power is turned
ON is
MPOS
displayed. Other displays may be used for special
specifications.
111
-9
(2) Confirmation of absolute position detection

1)
Currentmonitor
Turn the NC power and MDS Series input power
OFF and ON several timesin the emergency
stop state and confirm the following:
Check that the relationof the power OFF position and power ON position is not greatly
deviated. (However, there maybe a difference due to sequential axes or unbalanced axes.)
Confirm that ABSn, Rn and Pn do not move greatly. (However, Pn will change as shown
below, so 4094,4095
0, 1 movement can be considered.)
Encoder
type
OHA25K
Rn
N-
N+
c
N+ 2
X division
rN+3
1 motor rotation
Write down the ABSn, Rnand Pn values displayed when the zero point position is set. The
absolute position detection can
be confirmed with the following equation when absolute
position deviation occurs.
(Substitute the noted ABSn, Rn and Pn values
as ABSO,RO and PO.)
The above values will
be displayed on the monitor screen,
so confirm that the left side equals
the right sidewith the following equation.
ABSn = (Rn - RO + (Pn - PO)/x} *PIT*PCl/PCZ/hterpolation unit
Machine position= ABSn X Interpolation unit
2.2 Adjustment details

22.1 Vibration or vibration sounds occur
(1) A fine vibration is felt when the machine is touched, or the machine makes
a groaning sound.
I Lower 5. VGNl by 50 at a time. (Lower limit50)
Lower 11. IQG by50 at a time. (Lower limit 128)
Lower 12.IDG by 50 at a time. (Lower limit256)
Set 27. SSFl vfctl(bit 4), vfct2 (bit5) in the following order.
Set 27. SSFl aflt (bitF).

Use both 4) and 5) above.
(2) Vibration and sounds occur during rapid traverse.

Lower 5.VGNl by 50 at a time. (Lower limit50)
1)
Lower 11. IQG by 50 at atime. (Lower limit 128)
2)
3) Lower 12. IDG by 50 at a time. (Lower limit256)
Set 27. SSFl v
f
c
t
l (bit 4), vfct2 (bit5) in the following order.
4)
vfctl (bit4)
vfct2 (bit5)
5)
6)
7)
I
3)
Set 27. SSFl aflt (bitF).

Use both 4) and 5 ) above.
Set a value that the
is cutting feedspeed + 1OOrpm in 29. VCS and set the same value as
5. VGNl
in 6. VGN2.
Repeat rapid traverse, and lower6. VGN2 by 10 at a time. (Lower limit
0)
I11 - 11
2.2.2 The cutting surface precision is poor. The roundness is poor.

(1) The taper and arc
45" direction surface precision is poor.
Raise 5. VGNl by 20 at a time. (The limit is when vibration or sounds occur when stopping or during
1)
rapid traverse.)
Raise 8. VIA by 200 at a time. (Upper limit 2000)
2)
r;
Raise 5. VGNl by 20 at a time.

(The limitis when vibration or sounds occur when stopping or during rapid traverse.)
Raise 8. VIA by 200 at a time. (Uppeclimit
2000)
When the axis load is unbalanced, perform unbalance torque compensation
(32, TOF), and remove
the electrical unbalance element.
[YO]
on the I/F diagnosis screen sew0 monitor, and feed the axis with manual
Look at the power load
pulse by 10 to20 pulses in the + and - directions. If the current loadis positive, check the maximum
value, and if negative check the minimum value. Set the average of
value
the + and - directions
value inTOF.
<Example>
When + direction +50%, - direction -10% {(+50)+(-10)}/2 = +20
20
TOF
When + direction -3o%o, - direction -10% {(-30)+(-10)}/2 = -20
-20
TOF
Select the lost motion compensation type.
(Set the 27. SSFl bit 8 or bit 9 to validate lost motion
compensation.)
In the MDS Series, the lost motion compensation type 2 is the standard, and is suitable for the
following cases.
Highspeedmachining
Closedloop
Lost motion compensationtype I
Lost motion compensationtype 2
Set 27. SSFl lmctl (bit 8).
Set 27. SSFl Imct2 (bit 9).
Gradually increase 16. LMCl from 0 by
Look at the current load
[%] on theI/F diagnoss screen
20. If this is set too high, the axis will eat
sew0 monitor, and feed with manual feed etc. (the feed
into the workpiece.
rate is approx. 500 to lOOOmm/m).
Check the currentload value.
I Double the checked value and setit in 16.LMCl.
The 16. LMG1 optimum y a l ~ eis the maximum value where overshoot does not occur when one
pulse is fed and the direction is reversed.
If differing compensation amounts
are required in the- + direction and+
direction, set the
compensation gain for- + direction in 16. LMC1, and the
+
- direction compensation gain in
41. LMC2.
:.
:.
- -
Too large
111 - 12
--
--
~~~
~~~
~~
~~
(3)The load fluctuation is large during cutting and vibration or surface precision defects occur.
(Especially during heavy cutting)
Raise 5. VGNI by 20 at a time.
I)
(The limit is when vibration or sounds occur when stopping or during rapid traverse.)
Raise 8. VIA by 200 at a time. (Upper limit
2000)
2)
2.2.3 Overshooting occurs during positioning.A limit cycle occurs.

(I) For semi-closed loop
1)
Raise 8. VIA by 200 at a time. (Upper limit
2000)
2)
Note 1. If the overshoot amount is large
(5p or more), confirm the droop on servo
the monitor screen, and if
the same amountof overshooting occurs, take the above measures.
If no improvements are seen after the above measures are taken,
3.PGN1
set to approx.20, or
increase the axis specifications
acceleration/deceleration time constant.
If the droop does not overshoot, the motor is
itself
not overshooting and only the machine system is
overshooting. Adjust the machine system.
(2)For f u l l closed loop

Raise 8. VIA by200 at a time. (Upper limit
2000)
2)
Lower 3.PGNI by 5 at a time. (Lower limit
20.)
3)
However, set the interpolation between axes to the same value.
Set 27.SSFI ovstl(bit A), and increase 31.
OVSI by 2% at a time from2. (Upper limit IO)
4)
After settingOVSl, turn theNC power OFF and ON once.
Set 27.SSFI vcntl(bit 0), and increase7.VIL by 15 at a time from 0. (Upper limit 656)
5)
Return 27. SSFI vcntl (bit 0)to 0, set vcnt2 (bitl), and raise 7. VIL by 65 at a time from 0.
6)
(Upper limit 1640)
Try combining4) and 5 ) , or 4) and 6 ) .
7)
Note 1. If the overshooting or limit cycle
is improved with5 ) but the response is poor, perform the same
measure as 6).
Note 2. In case of full-closed loop as with Note1 for the semi-closed loop,if the droop on the sew0 monitor
screen is not overshooting, the overshooting is not occurring near the scale, and only the machine
system is overshooting. Adjust the machine system.
1)
I11 - 13
.
2.2.4 Accumulated feed occurs with pulse feed

(1)
Command several pulses, and confirm that the droop corresponding to the command pulse
is
occurring by checking the droop on the sew0 monitor screen.
Droop is not occurring
Droop is occurring
Movement has been made to near the
Raise 5 . VGNl by 50 at a time.
1)
1)
(The limit is when vibration
or sounds
position detector (scale, ball screw end
detector) in the motoror full closed loop.
occur when stoppingor during rapid
traverse.)
The following machine system
is
accumulated feed.
Raise 8. VIA by 200 at a time.
2)
Adjust the machine system.
(Upper limit2000)
Perform the same measures as 1.2.3
(2)
5).
2.3 Adjustment of special functions

2.3.1 High precision control mode
When
performing
high
precision
control,
the
various
parameters
for
performing
acceleration/
deceleration before interpolation, feed forward control and SHG control, etc. must be set.
(1) Outline
The delaycausedbytheNCsidecommandtimeconstants
is removedwithacceleration/
decelerationbeforeinterpolation.Thedelaycausedbytheposition
loop ontheservosideis
corrected only with
feed forward control in the
M300 Series, but the correction has been stabilized in
the M500 Series by combining SHGcontrol andfeed forward control.
(2) Basic parameters for high precision control
Servo parameter setting procedure to use
SHG control
No.
1
No.
SV003
svoo4
SV008
I I
SVOl5
I
I
PGNl
PGN2
SHGC
VIA
Position control
parameters
Speed control
parameters
Parameter
name
Class
I
I
Details
Parameter name Parameter
PGNl
When using SHG control in the position loop gain,
PGN2
set these three parameters with the following
combination.
SHGC SV057
3
When performing SHG control with the speed integral
VIA
gain, set 1900.
When performing SHG control with the acceleration
FFC
set aain.
forward
feed
100.
FFC
L
11
Combination of parameters during

SHG control
Remarks
No.?
I No.2
N0.3
33
38
47
102
125
86
281 225
Ia7
1900
I900
1900
Set 50 when using the
100
loo
100
low inertia motor.
I
I
II
1
\
Always observe the above relation for the three parameters related to position control.
Setting the same value as
PGNl and setting SHG control will double the conventional control's
position loop gain and
be effective.
As the response duringacceleration/deceleration in SHG control is smoother than the
conventional position control,
if PGNl = 33 (l/S) in the conventional position control, further gain
up may be possible with SHGcontrol.
I11 - 15
Y..yuuT(D
SHG control effect

The SHG control is capable of compensating the position tracking error that occurs with the
servo positionloop time constant as with the conventional feed forward control. The equivalent
1 to 3 are shown below.
feed forward gains for the above No.
,
No.
1
2
3
38
Equivalentfeed forward (%)

87
90
SHGC
187
225
281 125
PGN2
86 33
102
PGNl
47
94
The equivalent feed forward comparison are all based on PGNl

the = 33 conventional control.
Combination with feed forward control
If a compensation close to 100%
is required, combine the use with feed forward control.
In this case, the setting limit of the feed forward gain (fwd_g) is 40%. (Theoretically, 50% is
equivalent to 1OOYO,but excessive overshooting will occur.
If under 40%, the overshooting may
occur due to the machine,so determine the value by adjusting.)
Setting limits
All axes must be matched for the SHG control parameters (PGNl , PGN2, SHGC) and feed
forward gain (fwdg). (For interpolation axis)
1) Calculation of equivalent feed forwardYOduring SHG control.
(The equivalent feed forward gain is compared to when PGN1=33.)
Equivalent FF (%) = 100
41-
33
PGNl
)2
2) Calculation of equivalent feed forward

YOduring SHG control+ feed forward control
~~
~~
~~
f w d L
50
)2'x(
Equivalent FF (YO)
= 100
33
2.PGN1
)2
Setting of feed forward gain

SHG
control
Nom
fwdJ
Equivalent feed fonuard gain

(%)
~
No.1
40
95
No.2
40
97
Equivalent FFGis the

comparison of when
PGNl=33 SHG control
is not being used.
3. Troubleshooting (MDS-A/B Series)

3.1 Status display
/1\
WARNING
I. Do not touch the switches with wet hands. Failure to observe this could lead to electric shocks.
3. Do not open the front cover whole the powerON

is or during operation. Failure to observe this
CAUTION
1. Always check the parameters before starting. Depending on the machine, unforeseen operation
could take place.
2. Do not touch the servo amplifier fins, regenerative resistor

or servomotor, etc., while the power is
turned ON or immediately after turning the power
OFF. Some parts are heated to high
temperatures, and touching these could lead to bums.
The state of the drive unit is displayed on the 7-segment display on the drive unit and the NC servo
monitor screen.
Confirm one of these displays before troubleshooting.
Caution: The machine's power distribution box door must

be opened to confirm the drive unit's 7segment display. Take special care not to touch the conductive parts at this time.
(1) 7-segmentdisplay
The drive unit state is indicted with the 7-segment display on the drive unit.
When an alarm occurs, the alarm
No. will be displayed. If several alarms occur simultaneously for
one axis, the latest alarm
No. will be displayed.
Sento Drive Unit Status Display

Amplifier display
AA
Ab
AC
Ad
A
F#
9*
F# -. E*
F# -. **
#
*
**
Details
Initializing. Standby forNC power start up
(When NC power ON OFF)
(No display)
Initializing. Standby forNC power start up
(When NC power has not been turned
ON yet)
Initializing. Requesting parameter transmission
Initializing. Requesting parameter conversion
servo main
for tandby
IT start
NC display
Servo OFF
Servo ON
9*
E*
**
Warning
(* is 0 to F. Note "E6","E7" and "EA" are status displays).
Alarm occurrincr
: Axis No.
: Warning No.
: Alarm No. (Refer to <Servo alarm> <Warning> Tables on following pages.)
I11 - 17
The status display after initializing will repeat lighting and going out per axis and show the axes
in
order. An exampleis shown below.
(Example 1)
1st axis in a single-axis drive unit. Display of servo ON state.
(Example 2)
With the above axis. Displayof emergency stop signal input from NC.
(Example 3) L axis is 1st axis,

M axis is 2nd axisin 2-axes integrated drive unit. Display
of servo ON
state.
(Not lit)
(
L
i
)
(Example 4)
M axis state
L axis state
With the above axes. Display of motor overheat alarm (No.

46) in L axis. (Emergency
stop is applied onM axis)
> - r n
(Not
(Flicker)
L axis state
l
i
)
d
(Flier)
(Flicker)
M axis state
'
(Not lit)
7
(2) Servo monitor screen display(NC screen)

The NC will display the servo alarm in
No.
the servo alarm column
in the servo monitor screen when
an alarm occursin the drive unit. TheNos. are the same as the drive unit's 7-segment display but,
may differ depending on the alarm details. (Ex. When isthere
an obstaclein the communication with
the drive unit.)
Nothing will display when operations are normal.
Theservomonitorscreen
isdisplayedbypressingtheNC
functionselectionkey
.
(diagnosis), and then pressing menu key ISERVO MONITOR1
The servo alarm Nos. may display on other screens depending on the NC type. Refer to
instruction manual for details on this.
1the NC
plry
Abbr.
Name
f l f 2 f 3 f 4
11
ASE
12
ME
Memory error
13
SWE
error
16
RDl
,de
17
Meaming
Alarmtwaming
check P
e
r
i
d
Release Class
sewion
A9E
-
18
VVAT
1A
I;El
mr
error
processing
position detection
communication
m
&rial detector
mmunication
AR
0 - - -
The memoryIC (SRAM or FLROM) check sum was
AR
0 - - -
PR
PR
PR
o - -
PR
o - -
PR
PR
-
PR-
illegal.
converter error
The axis setting rotary switchwas set illegal in the

2-axes integrated drive unit.
error
SUB)
The software data processingwas not completed

within the normal time. Includes peripheral G/A
errors.
The differential inputof the U, V, or W phase of the
pole position detectiin signal of the OHE type
detector wre both "H"or "L".
The AD converterfor current detection did not
function correctly during initialization.
The absolute positionor pole position datafrom the
OHA type detector or serial pulse encoder
was not
corredly sent.
The initial communication with the serial encoder
installed on the ball screw end was not possible.
An error was detectedin the data stored in the

EEROM of the serialpulse encoder installed on the PR
ball screw end. (Alarm output by the detector.)
Deteriorationof the LEDs in the serial pulse
PR
encoder installed onthe ball screw end was
detected. (Alarm outputby the detector.)
1B
;cpu
> P U error (SUB)
1c
bled
ED error (SUB)
1D
aat
)ata error
1E
;OH
The thermal protectorbuilt in the detector operated

detector thermal
in the serial pulse encoder installed
on the ball
wmr (SUB)
screw end. (Alarm output by the detector.)
1F
i
t
r
e
hrnmunication error
SUB)
Communication withthe detector in the serial pulse

encoder installed on
the ball screw end was cut
off.
PR
20
JSl
40 signal detected1
The differential input

of the A, B or 2 phase signal
from the motor end installation detector
were both
"H" or "L". (Software detectionin B Series.)
PR
21
rls2
rlo signal detected2
The differential inputof the A, B or Z phase signal

from the machine end installation detector
were both
"H"or "L". (Software detection in B Series.)
PR
25
W E
I\b6olute
position lost
AR
o - -
26
NAE
Not used axis error
PR
PR
PR
o - -
PR
o o c
(SUB)
An error was detected

in the per rotation position
data of the serial pulse encoder installed on ball
the
screw end. (Alarm output
by the detector.)
The absolute position datain the absolute position

detector was lost.
A powt3r module erroroccurred in theaxis that is not
"F*' by theaxis setting rotary
being controlled set as
switch in the 2-axes integrated drive unit.
27
SCCPC
Absolute position
detection scale CPU
error
20
SOSP
Absolute position
overspeed
29
SABS
Absolute position
amiterror
2A
SlNC
Relativeposition
circuit error
26
SCPU
Scale CPU error
An error was detected in the CPU of the absolute

position linearscale. (Alarm output by the
detector.)
The scale moved atmore than45mdsec during
initialization with the absolute position linear
scale.
(Alarm output from the linearscale.)
A hardware error was detected
in the absolute
position detectioncircuit of the absolute position
linear scale. (Alarm output by the linear
scale.)
A hardware error was detected
in the relative
position detection circuit
of the absolute position
linear scale. (Alarm output by the linear scale.)
A CPU error was detectedin the serial pulse
encoder installed onthe motor end. (Alarm output
by the detector.)
I11 - 19
PR
PR
0
0
O
0
C
0
3. Troubleshooting (MDS-AlB Series)
Display
I
Abbr.
Name
Deterioration of theLEDsinthe
serial pulse
PR
ScaleLEDerrorencoderinstalledonthemotorendwasdetected.
(Alarm output by the detector.)
An error was detected in the per rotation position
PR
Scale dataerrordata
of the serial pulseencoderinstalledonthe
motor end. (Alarm output
by the detector.)
Communication withthe OHA type detector or
communication
PR
serial pulse encoder installed on the motor end and
error
the detector was cut
off.
2c
SLED
2D
SDAT
2F
STRE
31
os
OveFSpeed
32
PMOC
Power module
overcurrent
34
DP
CRC error
35
DE
Data error
36
TE
Transmission error
37
PE
Parameter error
38
TP1
Protocol error1
39
TP2
Protocol error 2
3A
oc
Overcurrent
An
excessive
current
speed.
PR
An overcurrentwas detected in the IPM used in the

servo drive's
circuit.
main
PR
The motor speed reached 1.2 times

the
rated
~~
A CRC erroroccurred in the communication data

from the NC.
The movement command data from
the NC is
abnormally large.
The cyclic data transmissionfrom the NCwas
terminated.
There is error in the servo parameters transmitted
from the NC duringservo drive initialization.
There was an errorin the communication protocol
with the NC. (Frame error)
There was an error inthe communication protocol
with the NC. (Information error)
flowed to the motor.

Overheating of the IPM used in theservo driver's
main circuit was detected.
(1)
A skip of the detector feedback signal pulse
. .
occurred in the OHE type or OHA type detector
used in thesemi-closed loop system and ball
screw
end
closed loop
system.
(2) A skip of the detector feedback signal pulse
in
the low-speed serial type absolute position
linear scale.
PR
PR
PR
A
-
PR
PR
PR
PR
PMOH
Power module Overheat
42
FE 1
Feedback error 1
43
FE2
Feedbackerror 2
A deviationoccurred in the feedback amount from

the motorenddetectorandmachineenddetectorin
the closed loop system.
PR
46
OHM
Motor oveheat
The motor or detedor thermal

protector
operated.
NR
OL 1
The motor current operatedin the range set with

overload
detection
level (parameter OLL) and
overload time constant (parameter OLT).
A current commandwith a maximum output current
exceeding 95% continued for 1 secondor more.
Overload
the
1
A
C
-
PR
38
50
Alann/waming
lelease
Meaming
PR
NR
~ _ _ _ _ ~
51
- OL2
52
OD1
Overload 2
NR
The actual position to the command exceeded the

excessive errorwidth 1 (parameter OD1) when the
NR
servo was turned ON.
Excessive error 1
_ _ ~
~
53
OD2
Excessive error 2
54
OD3
Excessiveerror 3
58
CLEO
Collision
detection
59
CLEl
actual position tothe command exceeded the

excessiveerrorwidth 2 (parameterOD2)whenthe
servo
was turned OFF.
~The motor currentdid not flow when the excessive
error1alarmwasdetected.(Addedwiththe
B
Series.)
A collision detection type 1 error was detected
durina the GO modal (rapid traverse).
Collision
detection
NR
NR
NR
~~
A collision detection type 1 error was detected

during the G1 modal (cuttingfeed).
NR
Abbr.
Meaming
Name
Acollisiondetection type 2 errorwasdetected.
Release Class
NR
Alarmhuaming
check Deriod
f l f 2
- -
An error occurred in the power supply unit. (Refer to
82 INSP
Power supply no signal supply or incorrect connection was detected.

(Only A Series)
The servo amplifier software process
was not
executed within the designated time.
Watch dog
AR
<Sew0 warnings>
Displsr
--I
Name
Meaming
Initial communication with the low-speed serial
90
PR
type absolute position linear scale was not
91
92
93
wAM
96
MPE
possible.
The absolute position serial data
was not properly
sentfromthe
OHA type detectorand low-speed
serial type absolute
position
linear
scale.
9 WAN
wAB
El WOL
E3
WAC
E4
W E
II
The format of the serial data from

the OHA type
detector wasincorred.
The absolute position counter cannot
be set as the
Absolute
position
absolute position data fluctuated when NC
the power
fluctuation
tumed
was
ON.
In the MP scale absolute detection system, an
excessive deviationin the motor end installation
MP scale feedback
detector and MP scale feedbadc amount was
error
detected.
In the MP scale absolute position detection
PR
system, an error was detected
in the offset data
MP scale offset error
read when theNC power was tumed ON.
An error was detected in the multi-rotation counter
High-speed serial mu)tiin the serial pulse encoder installed on the motor
rotation counter
end or ball screw end.
The voltage of the battery supplied to the absolute Batteryvow
position detector dropped.
An 80% level of the overload 1 alarm was detected.
Overload
warning
(If operation is continued, the overload1 alarm may
occur.)
Absolute position
The absolute position counter value
is illegal.The
absolute position mustbe initialized.
A parameter exceeding the setting range was set.
Parameter error warningThe illegal parameterw i l l be ignored andthe
previously set valuewill be held.
1'
I
97
9f
Release Class
I
I
111 - 21
I
I
A
A
IPRIA
A
A
A
IC
ct
Alarmhvaming
check period
3. Troubleshooting (RADS-A/B Series)
<Status displays other than alarms and warnings>

Dmplay
Alarmhnaming
Abbt.
Name
E6
AXE
Removing control axis
E7
NCE
NC emergency stop
E8EB
Meaming
The axis removal command is input from the NC.
The emergency stop command is input from the NC.
A warning was generated with the power supply
Release Class
check
f l f Z f 3 f 4
0 0 0
unit.
details.)
(Refer to the power supply unit item for
[Release]
AR : The alarm is released by turning the servo drive unit power
OFF and ON.
PR : The alarmis released by turning theNC power OFF and ON.
NR : The alarmis released by NC reset.
(However, overload alarm"50cannot be released until the load
is lowered passed the reset
level (50% of the current value on the monitor screen.))
- Automatically restored when the warning state is eliminated.
[Class]
c
A
: Detects both axes even during the Z-axes integrated drive unit.
: Detects each axis independently.
[Alarm/waming checkperiod]
fl
: When servo drive unit power is turned
ON.
f 2 : When NC power is turned ON (emergency stopON)
f 3 : During normal operation (servo
ON)
f4
: During axis removal (ready
ON, sew0 OFF)
(Note' : Warning "93" may occur after axis removal while installing the axis again.)
3. Troubleshooting (MDS-NB Series)
3.2 Troubleshooting per servo alarm
CAUTION
When an alarm occurs, remove

the cause of the alarm, confirm that an operation signal
is not
being input, and secure the safety. Then reset the alarm to resume operation.
When an alarm occurs
in the spindle drive, the servo will Oturn
F F and the motor will coast to a stop. Turn
the power OFF with an external sequence.
To release the alarm, remove the cause and then turn the power
ON.
(1) Alarm No.
[Meaning]
MDS-NB-V2)
Illegal setting of the axis setting rotary switch in the drive unit.
Investigation item
Confirm the rotary switch setting.One setting is 7 E.
Remedy
Correctly set. (Set aNo. that is
the axis No. minus 1.)
The L axis and M axis are set to Same as above.
the same No.
Replace the drive unit.
None of the above.
(2) Alarm No.

[Meaning]
Axis selectionerror(only
1121
error
Memory
Error in thedriveunitmemoryIC
peripheral G/A
Check for abnormalitiesin the

unit's peripheral environment.
(Ex. ambient temperature,
noise, grounding)
Alarm
period
check
(SRAM orFLROM)and
If1
f2
f3
I
I
f4
Remedy
Always occurs.
Returns to normal once, but
recurs periodically.
No special abnormalities were Replace the drive unit.
found.
An abnormalitywas found in the Take measures according to the
ambient peripheral environment. cause.
Ex. High temperature .....
confirm cooling fan
Grounding not enforced.....
add grounding measures.
111 - 23
(3) Alarm No.
[Meaning]
Software
processing
error
The drive unit software data processing was not completed
within the normal time or an illegal
IT process was input.
Investigation item
Remedy
Try replacing with the drive unit
Check whether the sew0
Changed
with the original software version.
software version was changed
recently.
Perform investigation item
2.
Not changed.
Always occurs. Confirm the repeatability.
Check for abnormalities in the No special abnormalities were Replace the drive unit.
found.
to the
~n
abnormalrty was found in the Take measures according
noise, grounding)
Ex. High temperature ...._
confirm cooling fan
.....
Grounding not enforced
(4) Alarm No.
[Meaning]
position
Pole
detection
error
, ,
: I q ~ ; h ~ ; ~ ~ r i ~
Error in the output of the OHE

type detector (motor end
installation)
phases
U, VI W
1) When the "H" differential inputsfrom the U, V or W phases
are both"L".
2) When the states of theU, V and W phases are all "H" or
'
"L".
Investigation item
Check theservo parameter
(SV25) setting value.
2 Tug the connector by hand to
Remedy
or "3" is set in the parameter Correctly set.
detector setting position even
though the OHE type detector is
not connected.
The setting is correct.
Correctly connect.
Disconnected (loose).
" O n
check whether the detector

connector (unit side and detector
side) isnot loose.
Not disconnected.
OFF and. check A connection defect was found.
3
the detectorcable connection
with a tester.
Connection was normal.
The alarm is on the unit.
4 Try connecting with another
normal axis unit and check
The alarm is on the detector.
whether the defectis on the unit
side or detector side. (Refer to
section incautions
the
2.3.)
I

Replace
the detector cable.
Turn
the power
Replace the detector (motor).
(5) Alarm No.
1171
AD converter error
Alarmcheckeriod
[Meaning] AD converter IC error in the drive unit
Investigation item
Confirm the repeatability.
for abnormalities in the

noise, grounding)
Remedy
Always occurs.
No special abnormalities were Check
found.
An abnormalitv was found in the Take measures according to the
Ex. High temperature __...
confirm cooling fan
Alarmcheckeriod
(6) Alarm No.
[Meaning]
Initial
communication
error
Initialcommunicationwiththedetectorwasnotpossibleina
system using the OHA
type detector (motor endor ball screw
end installation)or serial pulse encoder.
Investigation item
1
Check the servo parameter
"l",
"5' or " 9 is set in the
Remedy
Set correctly.
parameter detector setting

position even though theOHA
type detector is not connected.
Correctly connect.
Tug the connector by hand to Disconnected (loose).
Not disconnected.
side) is not b
s
e
.
Turn the powerOFF and check A connection defect was found. Replace the detector cable.
the detector cable connection
with a tester.
The alarm is on the detector. Replace the motor (detector).
(7) Alarm No. @ Serial pulse encoder communication error (SUB)
[Meaning]
The initial communication with the serial encoder installed

on
the ball screw end was not possible.
Investigation item
Perform the items
2 and following
for alarm No. "18".
Remedy
I11 - 25
,
( 8 ) Alarm No.
Serial pulse
encoder
CPU error (SUB)
Alarm
check
[Meaning] An error was detected in the data stored in theEEROM of the

serial
pulse
encoder
installed
on
the
ball
screw
end.
1
i
Investigation item
Perform the items
2 and following
for alarm No. "18 ' .
(9) Alarm No.
eriod
Remedy
Serial pulseencoder LED error (SUB)
[Meaning] Deterioration of the LEDs in the serial pulse encoder installed

on the ball screw end
was detected.
1
Investigation item
Perfom the items2 and following
for alarmNo. "18'.
(10) Alarm No.
Remedy
data error (SUB)
Alarm
check
Serial pulse
encoder
[Meaning] An error was detected in the per rotation position data of the
serial
pulse
encoder
installed
on the ball screw
end.
(Alarm outputby the detector.)
Investigation item
Perform the items
2 and following
for alarm No. "18.
~
(11) Alarm No.
Serial pulseencoderthermalerror
weaning] The thermal protectorbuiltin
the detectoroperatedin the

serial pulse encoder installed on the
ball screw end.
Investigation item
Perform the items
2 and following
for alarm No. ''18".
(12) Alarm No.

[Meaning]
I11 26
Aqn;hy;31ri;d,
Remedy
Communication with the detectorin the serial pulse encbder

installed on the ball screw endwas cut off.
Investigation resub
Remedy
Serial pulse encodercommunication error (SUB)
Investigation item
Perform the items 2 and following
for alarm No. "18.
eriod
Remedy
(13) Alarm No.

[Meaning]
No
detected
signal
eriod
check
Alarm
Error in the OHE,OHA type detector (motor end installation)

A,
B or 2 phase
Investigation r
e
s
u
k
in the parameter
detector setting position even
though the OHE or
OHA type
detector is not installed.
Tug the connectorby hand to
Not disconnected.
cOnnecfOr (unit side and detector
side) is notloo~e.
Turn the power OFF and check A connection defect was found.
with a tester.
The alarmis on the unit.
Try connecting with another
The alarmis on the detector.
the cautions in section 2.3.)
No special abnormalities were
Check for abnormalities in the
found.
'unit's peripheral environment.
An abnormality was found in the
ambient peripheral environment.
noise, grounding)
Investigation item
Check theservo parameter
(14) Alarm No.

weaning]
1211
"0'or "3" is set
Remedy
Correctly set.

Correctly connect.
Replace the detector cable.
Replace the motor (detector).

Take measures according to the
cause.
confirm coolingfan
No signal detected2
Error in the OHE-ET, OHA-ET type detector or each sale

(machine end installation)A, B or 2 phase.
Investigation b m
(-5)
setting.
"4","5"," 8 ' or "9' is set inthe
Remedy
Correctly set.
parameter detector setting

position even though the
OHEET or OHA-ET type detector or
each scale is not connected.
__
Perform investigationitem 2.
The valueis correct.-~ _ _
Perform the items foralarm "20".
111 - 27
.
.I"
(15) Alarm No.
1251
Absolute
check
Alarm
position
lost
period
[Alleaning] When absolute position data is lost.

This occurs when the power in the absolute position
detector is lost, and will return to normal when the unit's
2OOVAC is reset and zero point return is performed again.
~~~
~~
~~
Investigation reSub
Investigation item
Was disconnected.
Check whether the absolute
position detector cable (including Guideline:
battery connection cable) was left At delivery:
20 hours or more
disconnected for a while.
After 5 years:
10 hours or more
Was not disconnected.
Check whether a battery error Alarm occurred.
alarm occurred recently.
Did not occur.
Tug the detector connector (unit Was disconnected(loose).
and detector side) tosee if it has Was not disconnected.
disconnected.
Also check the cable between
the battery unit and drive unit.
was found.
Turn the powerOFF and check A. connection defect
the detector cablewnnedon
with a tester.
Check the repeatability.
Does not recur.
Perform zero point return again.

whether the defect is on the unit
the cautions in section
2.3.)
Always recurs.

found.
An abnormalitywas found in the
Remedy
Reset the amplifier's
2OOVAC
power and perform zero point
return again.
Perform investigation item 2.

Check the battery voltage.
Correctly connect.

Perform investigation item7 , and
if thereis no error, continue to
Use.

cause.grounding)
noise,
codfirm cooling fan
Grounding not enforced.
_.
..
(16)
period
check
Alarm
Alarm
error
No.
axisusedNot
[Meaning] A IPM alarm is occurring in an axis that is set"F"
asin the unit
axis settingrotary switch and which is not being controlled.
(Alarm only for 2-axes integrated drive unit)
~
~~~~
Investigation item
Check whether a wire
is
Connected.
connected to the motor output
terminal block( U W ) for the
Not connected.
axis set as
"F".
Check the repeatabillty.
Always recursor returns to
normal but recurs Deriodicallv.
Does not recur.
noise, grounding)
(17) Alarm No.
[Meaning]
Remedy
Perform the items for alarm
No.
"32".
if there is no error, continue to
use.

found.
An abnormality was found in the Take measures according to the
confirm cooling fan
Grounding not enforced..
...
Absolutepositiondetectionscale
CPU error
Alarm check Deriod
The CPU in the absolute position linear scale did not operate
correctly. (Alarm output by the linear scale.)
Investigation item
Remed
Tug the detectorcable
Is disconnected (orloose).
connector (unit side and
NC
Not disconnected.
side) tosee if it is disconnected.
2 Turn thepower OFF and check Connection is faultv.
the detector cable connection Connection is connect.
with a tester.
The alarm is on the detector. Perform investigation item4.
the cautionsin section 2.3.)
Check for abnormalities in the No special abnormalities were Replace the detector (linear
unit's peripheral environment. found.
scale.)
noise, grounding.)
ambient peripheral environment.cause.
Ex. High temperature _....
confirm cooling fan
1
~~~~~

I11 - 29
-.-,
.,,
(18) Alarm No.
1281
Absolute position overspeed
Alarm check period
weaning] The scale moved at more than 45mm/sec during initialization

when NC poweris turned ON with the absolute value linear:
scale. (Alarm output from the linear scale.)
~~
Remedy
Investigation kern
Investigation resub
Check the absolute value linear The specifications are not for the
Set the SV025: MTYP parameter
absolute value linear scale.
scale specifications.
correctly.
The specifications are for the Perform investigation item
2.
Is the machine moving during theIs moving.
Check the motor mechanical
alarm?
brakes and machine system.
Is not moving.
3.
Tug the detector connector (unit Was disconnected(loose).
Correctly connect.
and detector side) to
see if it has
disconnected.
4.
the detector cable connection Connection was normal.
5.
with a tester.
Try connectingwith another
The alarm is on the detector. Perform investigation item
6.
the cautionsin Section 2.3.)
Check for abnormalities
in the
No special abnormalities were Replace the detector (linear
&le).
An abnormalrty was found in the Take measures according to the
noise, grounding)
confirm cooling fan
...
(19) Alarm No.
Absolute
position
detection
circuit
error
, ,
liia~;h~~3~ri;d
[Meaning] An error O C C U K ~in~ the absolute position detection side circuit

oftheabsolutepositionlinearscale.(Outputfromthelinear
-
Scale)
Investigation item
Perform the items for alarm No.
'I28l.
111
- 30
Remedy
(20)Alarm No.
[Meaning]
Relativepositiondetectioncircuiterror
An error was detected in the linear scale side absolute position

detection circuit. (Output from the linear scale)
Investigation item
Remedy
Is the machine moving during the
Is not moving)
alarm?
Is moving
Perform
Is moving Check whether movement
is investigation item3.
normal atlow speeds.
Check the cautionary items
Is not moving
before turning the power
ON.
Check the wiring
Check the parameters
Correctly connect.
Tug the detector cable (unit andWas disconnected (loose).
detector side) tosee if it has
disconnected.
Turn the power OFF and check A connection defect was found. Replace the detector cable.
the dekstor cable connection
with a tester.
the cautions in section2.3.)
Check for abnormalities in the No special abnormalities were Replace the motor (detector).
found.
noise, grounding)
confirm cooling fan
...
(21) Alarm No.

[Meaning]
mning]
An error was detected in the data stored in the EEROM

of the
serial pulse encoder connected to the motor end.
(Alarm output from the detector or the linear scale.)
lnvestiaation item
Perform item3 and following of
alarm No. "2A".
(2Z)Alann No.
Serial pulseencoder CPU error
Remedy
Serial pulse
encoder LED error
Deterioration of the LEDs in the serial pulse encoder

connected tothe motor end was detected.
(Alarm output from the detector or the linear scale.)
Investigation item
alarm No. "X.
I11 - 31
~*....
Remedy
(23) Alarm No. (2D( Serial

pulse
encoder
data
error
weaning]
An error was detected in the per rotation position data of the

serial
pulse
encoder
connected
the
motor
to end.
(Alarm output from the detector)
Investigation item
alarm No. "2A".
(24) Alarm No.
[Meaning]
kimph~kqri;d,
Remedy
Detector
communication
error
Communication with theOHA type detector or serial pulse
encoder connected to the motor end and the detector
was cut
Off.
Investigation item
Perform item 3 and following
of
alarm No. "2A".
(25) Alarm No.

weaning]
1311
Remedy
Overspeed
The motor speed is exceeding the tolerable speed.

Investigation item
Remedy
Is moving
Perform
Is moving Check whether movement
is investigation item3.
Is not moving
before turning the power
ON.
Check the wiring
The
motor
has
3000mm
Correctly
set.
specifications, but is set for
2000rpm.
Correct to below the rated
speed.
Is too high.
Is set to below the rated
speed.
I Is the machine moving during theIs not moving
alarm?
2
normal at low
speeds.
Check thesew0 parameter

(MTYP) setting value:.
Is the rapid traverse rate too

high?
Motor speed=
Rapid traverse rate(mm/min) x pc2
Ball screw lead (mm)
PC1
is too low.
Check the current value
I I
6
displayed
. - on the servo
monitor screen.
Lower
the rapid
time
80% or moreof the maximum Check
whether
the traverse
time constant
constant so that the current value
value is displayed.
during rapid traverse
acceleration/decelertion is less
than 80% of the maximum value.
The setting is less than 80% of
Perform investigation
item 6.
the maximum value.
Perform items 2 and followingin

alarm No. "28'.
111 - 32
(26) Alarm No.
1321
Power module overcurrent
peaning] An overcurrent was detected in the IPM used by the servo

drive.
1
I
3
5
6
Investigation item
Remedy
Are theUVW phases on the unitThere is a short circuit or
Replace theUVW wires.
output short circuited.
conductivity.
Disconnect theUVW wires
from the terminal block and No conductivity. Perform investigation item
2.
the motor cannon plug and
check betweenUVW with a
tester.
Check theUVW wires for a
There is a short circuit
or
Replace theU W wires.
ground fault.
conductivity.
Check between the UVW
No conductivlty.
wiresandgroundingwitha
tester in the itemIstate.
Check for a motor ground fault. There is a short circuit
or
Replace the motor.
Check betweenthe U W
conductivity.
wires and groundingwith a
No conductivity.
megger testerin the item1
(Same level as other axes)
state.
The settings are incorrect.
Correctly set.
setting values.
Refer to the adjustment
procedures.
The settings are correct.
Tug the detector connector (unitWas disconnected (loose).
Correctly connect.
and detector side)
to see if it has Was
not
disconnected.
Perform
investigation
item
6.
disconnected.
with a tester.
Does not recur.
Recurs periodically.
Always recurs.
Try connectingwith another
Replace the motor (detector). The alarm is
the cautionsin section 2.3.)
Check for abnormalities in the No special abnormalities were Wait.
noise, grounding)
confirm cooling fan
I11 - 33
~~
(27) Alarmcheck
No. Alarm
CRC error
weaning]
A CRC error occurredin the communication data from the NC. f l
f2
period
f4
f3
~~
Investigation item
Tug the connection connectors The connectors are
between the NC and drive unit, disconnected (loose).
battery unit and drive unit, and Not disconnected.
between drive units to
see ifthey
are loose. Check that an
excessive force is not being
applied on the connector section.
Turn the powerOFF and check A connection defectwas found.
the connection of the
communication cable in item 1 Connection is normal.
with a tester. Try replacing with a
normal cable.
Check whether the NC and driveWas changed.
unit software version
was
recently changed.
Remedy
Correctly connect.
2.
Replace the communication

cable.
3.
Try returning to the original
software version.
If the problem is not solved,

perform investigation item 4.
Not changed.
Replace with another normal
The alarm is on the unit side. Replace the drive unit.
unit, and check whether the errorThe amplifier is not the cause. Perform investigation item
5.
is on the NC side or unit side.
I
Check for abnormalities in the No special abnormalities were I Replace the MCP card on theNC
side.
found.
to the
An abnormalitywas found in the Take measures according
noise, grounding)
Ex. High temperature.....
confirm cooling fan
...
(28) Alarm No.
1351
Alarm. check period

( f l I f2 I f3 I f4
Data error
weaning] ThemovementcommanddatafromtheNC
large.
1
Investigation item
(29) Alarm No.
is abnormally
Transmission
error
[Meaning] The cyclic data transmission from the NC was terminated.

Investigation item
1 Perform the items for alarmNo.
J
"34".
~ - l o l o l - ~
Remedy
k 4 z w p h ~ ~ 3 ~ r i ~ ,
Remedy
n.
1371
eriod
No.check
Alarm
Parameter
error
Alarm(30)
weaning]
during
There is error in the servo parameters transmitted from the

NC
0
~~
Investigation item
The illegal parameter No.
is
displayed on the NC diagnosis
Screen, so adjust the sento
parameter with the parameter
adjustment procedures.
The servo parameter (PIT)
(RNG) (PC?)(PC2) combination
is illegal or the setting range is
exceeded.
~~~~
is incorrect.
The parameterNo. is other than
1 to64.
Remedy
Set the correct parameter. The setting
when parameter No. is 101.
Illegal or setting range is
Refer to the parameter settings

and supplementary explanations
in the specifications, and reset to
the correct value.
The settingis correct.

No.
"34"-
Note thatif an alarm 37 occurs in a system using the

MDS-AVx Series servo software versionB and
above and provided with anOHE 25 encoder, there may be no signal(V, W phase).
(31)Alarm No.
Protocol
error
weaning] There was a protocol error in the communication with the NC.
(Frame error)
1
Investigation item
No.
Remedy
"34".
(32)Alarm No.
weaning]
Protocol
error
There was a protocol error in the communication with the NC.

(Information error)
Investigation item
No.
I I"34".
(33)
arm NO.
Remedy
Overcurrent
weaning] The motor drive current is excessive.
Investigationitem
1

No.
"32.
Remedy
exceed
(34)Alarm No.
Power
module
overheat
[Meaning] Overheating of the IPM usedin the servo drive was detected.
Investigation item
Alarm check period
&
Remedy
1 Investigate the heat radiating
environment
1) Rotation of fan on rear of
unit
2) Contamination of radiating
Take measures
fan is not rotating correctly. Replace the The
fan
to prevent cutting
Remarkable amounts of cutting Clean the fins oil or dust from
contacting the
fins.
radiating fins.
55C is exceeded.
ambient temperature
2
The grounding is incomplete. Investigate
installation
Correctlythe
ground.
noise measures for
the
Alarms occur easily when aTake
environment.
device on the left.
Replace the unit.
periphery?
I devices in the
I
I
II I
(35) Alarm No.
[Meaning]
1421
Feedback error 1
1) A skip of the detector feedback signal pulse occurred in the

OHE type or OHA type detector used in the semi-closed
loop system and ball screw end closed loop system.

2) A skip of the detector feedback'signal pulse in the lowspeed serial type absolute position linear scale.
Investigation-item1
Remedy
Perform the item 3 and following
for alarm No. "20".
(36) Alarm No.
[Meaning]
1431
Feedback error 2
1) A deviation occurred in the feedback amount from the
motor end detector and machine end detector

in the closed
2) The serial pulse encoderis detected in the semi-closed

loop.
1
Investigation item
Perform the items
3 and following
for alarm No."2A".
Remedy
(37) Alarm No.overheat

Motor
weaning]
Alarm
eriod check
The thermal protector built in the motor (detector) operated.

* In the MDS-B Series,thisisconnected
by the
serial
communication with the detector.
Remedy
Recurs within one minute
of start Perform investigation item3.
up.
Recurs periodically after
operating forsome time.
The motor is hot.
Lessen the operation pattern.
Investigation item
Check the motor temperature

when the alarm occurs.
The motor is not hot.

Tug the detector cable
connectors (unit side and motor disconnected (loose).
side cannons) tosee if they are Not disconnected.

perform investigation item3.
Correctly connect. The connectors are
loose.
Turn thepower OFF and check A connection defect was found. Replace the detector cable.
the detector cable connection Connection is normal.
with a tester.
Check the thermal relay terminal No conductivity or resistance is Perform investigation item6.
conductivity in the detector's
high.
cannon Wnnecfor with a tester. Normal (short circuit)
(Excluding MDS-B Series)
Between pin Nos. 'T' and 'V'
If the thermal connection is as No conductivityor large
Replace the motoror detector.
shown belowfor OHE25K-6,
resistance in the motor and
OHA25K-4, OSE104/105 and
detector thermal.
OSAl04/105, so cut the wire
Normal
between the motor and detector
with a joint amplifier, and check
the thermal conductivityfor each.
For OHE25K-85,0HA25K-85,
OHE25K-108 and OHA25K-108,
the thermal is only on the
detector side, so the detector is
defective if there is no
conductivity.
Replace with anothernormal axis The alarmis on the unit side.
unit, and check ifthe defect is on Occurs evenif unit is replaced.
Replace the unit.

the unit.
Check for abnormalities in the No special abnormalities were Replace the motor.
found.
unifs peripheral environment.
Take measures according to the An abnorm
(Ex. Ambient temperature,
noise, grounding)
confirm cooling fan
...
I11 - 37
3. Troubleshooting (MDS-AIB Series)
(38) Alarm No.
Overload 1
[Meaning] The time that the motor drive current exceeded the overload
detection level (parameterOLL) converted with stall
conversion exceeded the overload time constant (parameter
OLT).
Investigation item
(OLL) (OLT) setting values.
Standard setting values
OLL: 60 (unit: sec.)
n l
T-~ c n
UL I .
I J W

Check whether the motor is

hunting.
Remedy
The setting is not the standard Correct to the standard setting
value if special specifications are
setting value.
not being used.
The value is the standard settingPerform investigation item2.
value.
r
I
I The motor is hot.

Hunting is occurring.
Ease the operation pattern.
1
procedures and readjust.
Check the cable wiring and
connector connections.
Check for mistaken
parameter settings.
Adjust the gain.

perform investigationitem 4.
4.
Replace the unit.
5.
Hunting is not occurring.

Replace with another normal axis
unit and check whether the
Problem still occurs even after
defect is on the unit. (Refer to unit
the is replaced.
cautions in section2.3.)
Check the machine system.
Check if the current value on theThe value is abnormal.
6.
NC servo monitor screen is
The value is correct.
abnormally high when stopped
and operating.
Check for abnormalities in the No special abnormalities were Replace the motor (detector).
found.
noise, grounding)
Ex. High temperature .__..
confirm cooling fan
...
111
- 38
ISupplementary
explanation]
1) MDS-B Series
The unit was run in the region
of the thermal characteristics
shown with 'slanted lines below.
With the MDS-B Series, continuous protection characteristics were realized by changing the overload
alarm detection process.
Note 1) The overload 1 detection region canbe changed with the parameters(SV021: )LT, SV022: OLL) in the same manner
as MDS-A. However, as long as there is no particular reason, use the standard parameters.
Note 2) With this alarm, as the overload detection method has been changed, the alarm occurrence time and the value
displayed at "Overload(YO)"
on the servo monitor screen may differ fromMDS-A
the Series even when usingthe same
operation pattern.
Note 3) To prevent operationfrom being resumed immediately from the overload state, this alarm cannot be reset until the
control power( L l l , L12) continuity stateis not continued for several minutes after the alarm occurs.
The condition for resetting the alarm
is that the "Overload (YO)''
display value must drop to
50% or less. The time to wait
for this alarm to reset will differ accordingto the servo parameters (OLT and OLL), but
is approximately five minutes
with the standard parameters.
If the control poweris turned ON again immediately after the alarm has occurred,
the alarm will not
be reset due to the
above operation.Wait at least 5 minutes in the continuity state, and then carry out
NC reset or turn the power ON
again.
@ Overload 1 detection rangefor other than HA-LHl5K2-Sl

Overload protection characteristics
1000
0.1
0
50
&LL-SO
t OLL
150
2 00
250
300
350
Motor current (YOto stall rating)
Overload 1 detection range for HA-LHSKZ-S?

1000
I00
10
0.1
1
0
I11 - 39
3. Trou bleshootinq(MDS-NB Series)
2)
MDS-A series
A
loo -
50
Operation nut possible

range due to current
h
0
limit
Q)
E
i=
10 -
5 .
I Fixed value
0.5
100
200
300
400
500
OLL = 150%
OLT = 60 sec.
Note 2) The A level is for parameter SVOl3: ILMTl = 500.
The A level will change proportionally whenthe parameteris changed.
Note 3) The motor's rated current ratio and time shown with 0 ,0,x and A symbols in the
diagram will differ according to the motor.
Note 1) Parameterstandardsettingvalue
(39)
Alarm
No.
Overload 2
Alarm check Deriod
[Meaning] A current command that is 95% or more of the amplifier's

maximum output current value continued
for Isecond or
more.
~~~
~~
Investigation item
Check if the PN voltage is beingThe voltageis supplied.
supplied to the amplifier.
The voltage is not supplied.
Check the axis where the
alarm occurred, and the axis
farthest from the power
supply.
Confirm that the power supply There is no voltage at the PN
unit CHARGE lamp is lit and terminal. (The lampis not lit.)
check the PN terminal voltage. There is a voltage at the
PN
I terminal.
Is an abnormally large current
The maximum value exceeds
value displayed on the NC servo
monitor screen during
table on the previous page.
acceleration/deceleration?
A correct value is displayed.
for alarm No."50".
I11 - 41
-
"..
..I
Remedy
Check the power supply

unit.
. .
Check the PN wiring between the
I units.
Lengthen the
the
acceleration/decelerationtime level indicated
constant, and lower to
80% of the
limit value.
[supplementary explanation1
1) MDS-B Series
The unit was run in the region
of the thermal characteristics shown with slanted lines
below.
Overload 2 detection rangefor other thanHA-LHlSKZ-SI

t 000
100
h
0
Q)
u)
10
i=
0.1
IO
@ Overload 2 detection rangefor HA-LHSKZ-SI
characteristics
protection
Overload
When rotating
When stopped
1000
100
0.1
0
50
1 OLL-
100
so
OLL
200
150
Motor current (YOto stall rating)
111 42
250
300
350
3. Troubleshootina (MDS-A/B Series)
2)
MDS-Aseries
100
overload 1
Overload 2
50
Continuous operation range

Operation not possible
range due to current
limit
i=
10
1
0.5
I
100
200
300
400
500
= 150%
OLT = 60 sec.
Note 2) The A level is for parameter SVOl3: ILMTl = 500.
changed.
The A level will change proportionally when the parameter is
Note 3) The motor's rated current ratio and time shown with 0 ,0 , x and A symbols in the
diagram will differ according to the motor.
Note 1) Parameter standardsettingvalueOLL
I11 - 43
oI__.
.. .
Motor
Level
Time
Level
Level
Time
Level
Time
HA 40N
OLL
OLT
250
IO
450%
1 sec.
472%
80N
OLL
OLT
250
10
400
424
1OON
OLL
OLT
250
10
285
300
200N
OLL
OLT
200
250
260
300N
OLL
OLT
180
220
230
700N
OLL
OLT
180
220
231
900N
OLL
OLT
180
240
252
053
OLL
OLT
250
10
265
279
13
OLL
OLT
250
10
265
279
23N
OLL
OLT
250
10
255
270
33N
OLL
OLT
250
10
255
270
43N
OLL
OLT
250
10
320
340
83N
OLL
OLT
250
10
300
318
103N
OLL
OLT
220
275
291
203N
OLL
OLT
190
235
246
303N
OLL
OLT
180
195
205
703N
OLL
OLT
180
195
207
50NL
OLL
OLT
250
10
400
425
1OONL
OLL
OLT
250
10
330
350
150NL
OLL
OLT
250
10
345
365
200NL
OLL
OLT
200
10
220
231
300NL
OLL
OLT
200
215
228
500NL
OLL
OLT
180
180
193
204
193
247
260
LH11K2-SI
LH15K2-Sl
(40)Alarm No.
Excessive
error
[Meaning] The actual position to the command exceeded the value set in
parameter setting valueOD1 (excessive error width during
servo ON) when the servo was turnedON.
The actual machine position deviated an amount exceeding the value set in OD1 from the ideal
machine position for the command position.
This will occurif the actual machine position enters the shaded area
shown below.
Position
1I
servo OFF
Investigation item
Check if the PN voltage is being
supplied to the amplifier.
Check the axis where the
alarm occurred, and theaxis
farthest from the power
supply.
Confirm that the power supply
unit CHARGE lamp is lit and
check the PN terminal voltage.
(OD1) setting value.
OD1 = 002 =
Rapid traverse rate
(rndrnin.1
60 x PGNl
Os (mm)
Ideal machine position
Time
Servo ON
The voltageis supplied.
Remedy
The voltageis not supplied.
There is no voltage at the

PN
terminal. (The lamp is not lit.)
PN
There is a voltage at the
terminal. units.
The setting is not the standard
setting value.
Check the power supply unit.
The setting is the standard

setting value.

for alarm No. "50".
I11 - 45
..
-.

Correct to the standard setting
not being used.
3. Troubleshooting (RADS-NB Series)
(41) Alarm No.
weaning)
1531
Excessive
error
li~rph~~3~ri;d,
The actual position to the command exceeded the value set in

parametersettingvalue OD2 (excessiveerrorwidthduring
servo OFF) duringsew0 OFF.
Investigation item
OD1 = OD2 =
Rapid traverse rate
(mrWrnin.1
60 x PGN1
0.5 (mm)
Check if the machineis moving

during servo OFF.
Investigation results Remedy

The settingis not the standard Correct to the standard setting
setting value.
not being used.
2.
setting value.
Is moving.
-
Is not moving.
Is disconnected (loose).
Tug the communication cable

connector from the NC to the Normal.
terminator (unit side and NC
side) tosee if it is disconnected.
Turn the power OFF, and check A connection defectwas found.
the communication cable
Normal.
connection with a tester.
Try changing with a normal
cable.
Replacewith another normal axisThe alarmis on the unit.
unk and check whether the
defect is on the unit. (Refer to unit
the is replaced.
cautions in section2.3.)
Check the machine and

mechanical brakes.
3.
Correctly connect.
4.
cable.
5.
Replace the unit.
Replace the NC side MCP card.
1
If the problemis not solved,
perform investigation item
6.
Correctly connect.
7.
Tug the detector cable connectorIs disconnected (loose).

Normal.
(unit side and motor side cannon)
to checkif it is disconnected.
Tum the power OFF, and checkA connection defectwas found.
8.
Normal.
with a tester.
found.
to the
An abnormality was found in the Take measures according
noise, grounding)
confirm cooling fan
...
(42) Alarm No.

[Illleaning]
was
1541
Excessive
error
eriod
check
Alarm
The motor current did not flow when the excessive error
1
alarm
Investigation item
Remedy
if the PN voltage is being The voltage is supplied. Check Perform investigation item3.
supplied to the drive unit.
is no voltage at the PN Check the power supply unit. There
unit CHARGElamp is lit and terminal. (The lamp is not lit.)
check thePN terminal voltage. There is a voltage at the
Check the PN wiring between
PN
the units.
terminal.
Check whether the motor powerThe power wire is not connected Correctly connect the power
wire is connected to the motor. or the power wire is broken. wire.
Disconnect the power wire The power wire is correctly
from the terminal block, and connected.
check between theUVW
wires with a tester.
Replace the motor.
The alarm is on the motor.
the cautions in section
2.3.)
(43)Alarm No.
Collision detection 0 (CLEO)
eriod
check
Alarm
[Meaning] A collision detection type 1 error was detected during theGO

modal (rapid traverse).
A disturbance torque that exceeds the external disturbance
torque was detected.
[Detecting] During servo ON
Investigation item
Remedy
Is the collision detection functionThe collision detection function Perform investigation item2.
is not used.
being used?
Check whether the machine has
Modify so that the machine does
The machine has collided.
not collide.
collided.
The collision detection function Perform investigation item3.
is used, but the machine has not
collided.
Change sv060 (TLMT) to "0".
The setting is incorrect.
2 Check the parameters.
Is sv060 (TLMT) set to"O"?
Increase the time constant, and
3 Check whether the current has The current is90% or more of
reached the current limit value the current limit value.
or 90% of the limit value .during
The current is less than
90% of Perform investigation item4.
normal rapid traverse
the current limit value.
acceleration/deceleration.
4
Adjust the collision detection The alarm does not occur.

function again, and try
The alarm occurs.
operation. (Refer to the separate
collision detection function
specifications.)
Is vibrating.
Does the machineor current
vibrate?
Try increasing the detection

level.
Is not vibrating.
The alarm does not occur.
The alarm occurs.
I11 - 47
Eliminate the vibration by

adjusting the gain, etc., and then
If the problem is not solved
by
replacing the unit, try increasing
the level.
, Replace the unit.
section.
(44) Alarm No.
[Meaning]
1 (CLEI)
Collision
detection
eriod
check
Alarm
A collision detection type 1 error was detected during the

G1
modal (cutting feed).

A disturbance torque that exceeds the external disturbance
torque was detected.
Investigation item
Remedy
1 Is the collision detection functionThe collision detection function Perform investigationitem 2.
is not used.
being used?
Check whether the machine hasThe machine has collided.
collided.
not collide.
The collision detection function Perform investigation item 3.
is used, but the machine has not
collided.
Change sv060 (TLMT)to "0".
The setting
2 Check the parameters.
- is incorrect.
IS sv060 (TLMT) set to
"o~'?
3 Check whether the current has The current is90% or more of
reached the currentlimit value
or 90% of the limit value during
item 4.
The current is less than
90% of Perform investigation
normal cutting feed
4
The alarm does not occur. Adjust the collision detection
The alarm occurs.
specifications.)
Is vibrating.
5 Does the machineor current
vibrate?
perform investigationitem 4.
Is not vibrating.
If the problemis not solvedby
6 Try increasing the detection
the level.
level*
The alarm occurs. Redace the unit:
II
(45) Alarm No.
detection
Collision
eriod
check
Alarm
[Meaning] A collision detectiontype 2 error was detected.

Acurrentcommandatthemaximumperformanceofthedrive
unit was detected.
Investigationresults
Investigation item
Perform the investigation items
for alarm 58.
(46) Alarm No.
Remedy
to
[Meaning] An error occurred in the power supply unit.
1 I
Investigation item
Refer to11. MDS-NB-CV power
supply
Remedy
I
I11 - 48
3. Troubleshootina (MDS-A/B Series)
(47) Alarm No.

weaning]
Power supply no signal
The cable connected to the power supply is broken

or the
connection is mistaken.
3
~
Investigation item
Check if the connector for the
communication cablewith the
power supplyis disconnected.
Turn thepower OFF and check
the cable connectionwith a
tester.
Try changing the cable
with a
normal cable.
Connect with another normal
axis unit, and check
if the defect
is on the drive unit side
or power
supply side.
(48)Alarm No.
weaning]

noise, grounding)
(49) Alarm No.
Alarm check period

I f 1 I f Z l f 3 1 f 4 1
I0
~~
0
~-
Remedy
software version.
Not changed.
2.
found.
the Take measures according to the An abnorm
confirm cooling fan
...
add grounding measures. I
The
initial
communication
with
the
low
speed
serial
type
absolute position linearscale was not possible.
Alarm check period

f l I f2 I f3 I f4
- ~
Remedy
Communication
error
The absolute position serial data was not properly sent during
normal operation.
Investigation item
Perform the items3 and following
for alarm No. "25"
It was changed.
Low speed serialinitialcommunicationerror
(50) Warning No.

cable.
The aiarmis on the drive unit

side.
The alarmis on the power supplyReplace the power supply unit.
side.
Investigation item
Perform investigation items of
alarm No.58.
weaning]
A broken wireor incorrect

connection was found.
The connection is normal.
The servo drive software process wasnotexecutedwithinthe

designated time.
Investigation item
[Illleaning]
Remedy
Correctly connect.
Watch dog
recently.
Is not disconnected.
111 - 49
Remedy
1
O
(51) Warning NO.

[Meaning]
Serialformaterror
The format of the serial data

from the absolute position
detector was incorrect.
Investigation item
Perform the items
3 and following
for alarmNo. "25@
(52) Warning No.
1931
Remedy
Absolute position fluctuation

Alarm
check
period
[Meaning] The absolute position counter cannot be set as the absolute

position data fluctuated when the
NC power was turnedON.
1
Investigation item
for alarmNo. "25"
(53) Alarm
MP No.
weaning]
scale feedback error

In the MP scale absolute detection system, an excessive
deviationinthemotorendinstallationdetectorand
MP scale
feedback amountwas detected.
f1
f2
f3
f4
Remedy
li~~;h~kqri;d,
0
1
Investigation item
Perform the items
3 and following
for alarm No. '25"
( 5 4 ) Alarm No.
1971 MP offset
scale
Remedy
error
Alarm check period

f2
f3
f4
[Meaning] In the MP scale absolute position detection system, an error f1
was detected in the offset dataread when the NC power was
0
turned ON.
1
1
Investigation item
Perform the items
3 and following
for alarmNo. "25"
Remedy
(55)Alarm No. @ High-speed serialmulti-rotationcountererrorAlanncheckeriod

[Meaning]
An error was detectedin the multi-rotation counter in the serial

pulse encoder connected to the motor end or ball screw end.
-
Investigation item

for alarm No. '25"
111 - 50
Remedy
( 5 6 ) Warning
eriod
No.
check
Alarm
drop
voltage
Battery
[meaning] The voltage of the battery supplied to the absolute position

detector
pped.
1
0
1
Investigation item
Remedy
Check the battery unit voltage. The battery voltage has dropped.Replace the battery.
There is no error in the battery Perform investigation item2.
voltage.
Perform the items3 and following
for alarm No. "25'
(57) Warning
period
No.check
Alarm
warning
Overload
[Meaning] An 80% level of the overload 1 alarm was detected.

As this is not an alarm, continued use
is possible, but the
overload 1 alarm may occur.
Investigation item
Check whether the motoris hot.
The motoris not hot.
Check if there is an error when

acceleration/ decelerationis
The motoris hot.

Operation is possible without
error
Remedy
No.
w&nu
uu
perfomred.
Operation is abnormal.
( 5 8 ) Warning No.
[Meaning]

1. If the operation pattern canbe
eased, ease it.
2. If operation is possible without
an alarm occurring, continue
use.
Perform the items
3 and following
for alarm No. "50".
Absolute
position
counter
warning
Alarm
check
eriod
The absolute position counter valueis illegal.

If thepower is being turned ON for the first time, perform
zero point return, turn the power
OFF and ON once to
restore the value.
Investigation item
Remedy
Investigate the state where the Occurs when NC power
is turned Check the battery voltage,
warning occurred.
ON.
perform zero point return, and
then turn DowerOFF and ON.
Perform the items for alarm"25".
Occurs during operation.
Check the battery voltage.
An alarm occurred.
Check the detector and cable.
Did not occur.
I11 - 51
(59) Warning NO.
Parameter
error
warning
[Meaning] A parameter exceeding the setting range was set.

The illegal parameter will be ignored and the previously setI
value will be held.
1
Investigation item
Set the correct value according to
the parameter adjustment
procedure.
(60) Warning No.
Alarm check Period
- l o l o l - l
Remedy
NC emergency
stop
[Meaning] An emergency stop signal is being sent from the NC or an

alarm occurred in another axis.
Investigation item
Remedy
stop switch is activated.
Emergency stopis released.
Release the emergency stop.
The machinestarts up normally. Normal
"E7" is still displayed.
Check if a terminator or batteryAbnormal place found
Correct the abnormality.
unit is connected or if
"34".
Normal
disconnected.
I Check if the NC side emergency Emergency stopis activated.
2
3
3.3 Precautions
(1) When changing the motor and amplifier combination due to troubleshooting, avoid running the
motor with an amplifier that has a capacity larger than the designated amplifier. The motor may be
demagnetized.
However, checkingin the emergency stop stateis no problem.
Running the motor with an amplifier having a capacity smaller than that designated
is no problem.
4. Troubleshooting (MDS-C1 Series)

4.1 Servo warnings and servo alarms
(1) Precautions and matters to confirm
If an error occurs in the servo system, a servo warning or servo alarm will
sew0
occur.
warning
If a or
servo alarm occurs, pay attention to the following points and check the state of the system. Then,
carry out the inspections and repairs described in this section.
CAUTION
1. This servo system uses a large capacity electrolytic capacitor. When the
CHARGE lamp on
-CV)in the system is lit, there
is still a voltage in the
the front of the power supply (MDS-C1
unit
unit. Take care to prevent electric shocks and short circuits. (The voltage will remain for
several minutes after the power
is turned OFF.)
2. The continuity inside the driver cannot be checked due to the structure.
3. Do not carry out a megger test as the driver could be damaged.

<Matters to confirm>
1. What alarm No. is displayed?
2. Can the error or fault be repeated? (Investigate alarm history)
3. Is the motor and servo driver temperature and ambient temperature correct?
4. Are the servo driver, control unit and motor grounded?
5. Did the problem occur during acceleration, deceleration or constant speed operation?
What was thespeed?
6. Is there any difference in the state during forward run and reverse run operation?
7 . Was there a instantaneous power failure?
8. Did theproblem occur when a certain operationor command was carried out?
9. How often does the problem occur?
10. Does the problem occur when the load is applied or removed?
11. Has the driver unit been replaced, any part been replaced, or any remedial measure been
taken?
12. How many years have passed since operation was started?
13. Is the power voltage normal?Is there any great fluctuation according to the time zone?
11
F1 (flicker)
F +axisNo.
37 (flicker)
Alarm No.
(flicker)
F1
F + axis No.
37
lit (flicker)
Not
Alarm No.
LED display during servo alarm
F1
F + axis No.
9F
Warning No.
F1
F + axis No.
lit 9F
Warning No.
LED display during servo warning
I11 - 53
*
.
Not
4. Troubleshooting (MDS-CI Series)

~~~~
~~~
~~
(2) Troubleshooting at start up

If the NC system does not start up correctly and a system error occurs when
NCthe
power is turned
ON,the servo driver may not have been started
up correctly.
Confirm theLED display on the driver, and take measures according to this section.
~~
LED display
AA
Symptom
Initial communication
with the NC was not
completed correctly.
Ab
Initial communication
with the NC was not
carried out.
Investigation
method
I
Remedy
I
Is there any other driver set to theSet correctly.
same axis No.?
Set correctly.
Is the number of NC controlled
axes correct?
Is the connector (CNlA, CN1 B) Connect correctly.
disconnected?
Replace the cable.
Is the cable disconnected?
Check the continuity witha tester.
The axis is not used,or is Is the axis setting rotary switch setSet correctly.
I between 7 and F'? I
I
set to disabled.
Connect correctly.
Communication withNC is Is the connector (CNlA, CNlB)
disconnected?
incorrect.
Replace the cable.
Is the cable disconnected?
Check the continuity witha tester.
Cause of occurrence
The driver axisNrsetting
is incorrect.
The NC setting is
incorrect.
Communication withNC is
incorrect.
~~
I11 - 54
4. Troubleshooting (MDS-Cl Series)
(3) List of servo alarms and warnings

No.
10
Abbr.
11
12
13
14
15
ASE
ME
SWE
SWE2
Name
Axis selection error

Memoryerror
Software processing error
Software processing error2
16r R
o
l PdeposiWndetedkmemrrl
17
18
19
ADE
WAT
1A
stei
1B
Scpu
1C
1D
1E
S M
Sdat
Sohe
1F
stre
20
21
hlst
AIC
RS
AR
AR
PR
PR
C
C
C
No.
40
41
43
44
PR
Initial communication error

Serial detector initial communication
PR
error (SUB)
sABs
s,Nc
PR
4B
A
A
A
4C
4D
4E
4F
BV
A
50
NS2
PR
EEPROM/LED error(SUB)
PR
Data error (SUB)
PR
ROM--hemal error
(SUB)
Serial detector communication error PR
(SUB)
PR
. w m t ! $ p d 3
PR
No signal 2
OLl
OL2
OS
~Spemdde#Wtimrrwwarhm
PR
SP
Absdutepositionlost
AR
PR
PR
PR
A
C
A
A
54
55
56
57
OD3
ABSE
NAE
22
23
24
25
26
27
28
29
Natusedaxiserror
SCcpu Scale CPU error (SUB)

Sosp Scaleoverspeted (SUB)
Sabs
detectbn arcuit
error (SUB)
PR
28
SCPU
Relative position detection circuit error PR

(SUB)
PR
ScaleCPUerror
2C
20
SLED
EEPROM/LEDerror
PR
SDAT
Scaledataerror
PR
2E
SRRER0"cmw
2F
STRE
30
31
32
33
34
35
36
37
38
39
3A
A
A
A
A
A
A
PR
Serial detector communication error PR

OR 3
PR
3
U
e
r
PR
OS
Overspeed
PR
PMOC Overcurrent ( I P M error)
w ovrrrrdcogb
PR
DP
PR
NC communication CRC error
DE
NC communication Data error
NC comrnunicationComrnunicationemr PR
TE
PR
PE
Initial parameter error
TP1
NC communication Protocol error 1 PR
TP2 NC communication Protocol error 2 PR
PR
OC
Overcurrent
PMOH Overheat (IPM error)
PR
PR
PR
PR
SP
NR
SP
NR
A
A
PR VL
fPRfVC
r n f
Relative position detection circuit
error
NR
A
NR
A
NR 52
A
ON) OD1
NR
A
OFF) OD2
53
NR
A
Excessive error3 (no power)
Overload detection 1
51
Overload detection 2
Excessive error 1 (at servo
Excessiveerror2 (at servo
59
GLGl
Collision detection method1.Gl
5A
CLT2
Collision
detection
method
2
NR
NR
NR
SP
5B
5C
ORFE f0riQntatiaWfeedbadrenor
50
5E
5F
60
61
62
0
1
1
641
A
A
I AIC
NR 58 A
Collision detection method1.GO CLGO
SVJ
A
A
SVJ 63
C
A PR
65
C
66
A
67
C dog68
RS
1 PR I SP
45
BV 46
OHM Motor overheat
A PR
47
A PR
48SCGPU
IScaleCPU error
49
SOSP Scaleoverspeeb
M u t e position dtztedion circuit
A
4A
AD converter m r
CPU error(SUB)
Abbr.
Name
KE3 A-TK unit changeover error
una communication error
KE2 A-TK
FE1 42
C
1
Feedbackerror
FE2 Feedbackerror2
CAXC C axis changeover a l a m
1
1
2
3
4
5
6
7
8
69
6A
flnstantaneowp o w e r failure
f ~ o u r r t module
t overcurrent
PR
R
[PR] V
\Auxiliary
regeneration
error
[PRI V
relay
Rush
error
Open phase
Watch
/Gourd fauft
1 PR 1V/R
1 i
[PRf V
vm
] A R
1 PR v
A
1Contadormeltiq
[PRI V
8
/Rush mlayrnetting
PR [V/R
6B ,
3c
Main circuit m o r
PR ]V/R
6C
C
3D
6D
D
3E
AR vm
6E [
E
lNlemoryemr
3F
AR 1 V/R
6F
f
fAoenor (PS error)
Note 1) For RS, PR: Reset by turning NC power OFF, AR: Reset by turning servo driver power
OFF.
*: This is a warning display, andthe servo will not turn OFF.
Note 2) For N C , A: Alarm occurring for each axis, C: Common alarm
in driver, SP: Spindle alarm,SVJ: MDS-A-SVJ alarm,
AV: MDS-A-Vx alarm, BV: MDS-B-Vx alarm, VL: MDS-B-Vx4L alarm, V: Power regeneration power supply alarm.
R: Resistor regeneration power supply alarm
38
I11 - 55
1
1
No.
Abbr.
70
Name
I RS I
l~~~~
71
emergr#rcystap
~~
72
73
1.
74/
75
J
K
/ovler-.regeneration
/Regerrerative&storover)leat
L - 1
76
I F - w a w m m
77
~PowlermaduleOr)/fin (R) overheat

I
I
I
PR
PR
NR
AIC
No.
Abbr.
RS
Name
AIC
A0
A1
t
1 R,
A2
R
I V/R
ARI
A3
A4
A5
A6 V
PR
I
1 V/R
A7
In READY OFF (n is control axis No.)

(In servo ON (nis control axis No.)
Dn
In SERVO OFF (n is control axis No.)
lcontrol axis No. display (n is control axis No.)
Fn
Note 1) For R S , PR: Reset by turningNC power OFF, AR: Reset by turning servo driver power OFF.
*: This is a warning display, and the servo
w i l l not turnOFF.
Note 2) For A/C, A: Alarm occurring for each axis, C: Common alarm in driver, SP: Spindle alarm, SVJ: MDS-A-SVJ alarm,
AV: MDS-A-Vx alarm, BV: MDS-B-Vx alarm, VL: MDS-B-Vx4L alarm, V: Power regeneration p o w e r supply alarm,
R: Resistor regenerationpower supply alarm
Bn
Cn
111 - 56
(4) Alarm details

Servo alarms
Abbr. I
Details
I RS I N C
During theseF-check when the driver power was
turned ON, an error
( 5 ) LED AR
C
ME
Memoryerror
was detected
the
Inmemory
IC/FB
IC.
(Refer
the
tosection
display No. at memory error.)
SWE Software processingerrorThesoftwaredataprocessdidnotendwithinthespecifiedtime.PRC
SWE2 Sofhware processing
error The
2 current
processing
processor
is not
operating
correctly.
PR
C
During the self-check when the driver power was turned ON, an
ADE AD converter error
PRerrorA
was detectedin the N D converter for current detection.
Initial communication with the high-speed serial detector connected
PR
A
wAT lnitiilcommunication error
to the motor endwas not possible.
In
the
system
using
the
OHA25K-ET
or
high-speed
serial
detector
as
stei Serial detectorinitial
themachineenddetector,initialcommunicationwiththedetectorPRA
communication error (SUB) was not possible.
An errorwas detected in the data storedin the EEPROM of the
PR
A
Scpu CPU
high-speed serial detector connected to the machine end.
error
Name
The linear scale connected to the machine end detected an

EEPROMED error(SUB)EEPROMerror.
Or, deteriorationoftheLEDswasdetected
in thePRA
An error was detected at a position within one rotation of the highSdat Data error (SUB)
PR
speed serial detector connected
to the machine end.
The linear scale connected
to the machine end detected an error
in
ROM-RAM/thermal error
sohe (SUB)
the.RO".
Or, the thermalprotectorbuiltin
the high-speedPRA
senal detector connected to the machine end activated.
detector
Communication
with
the
high-speed
serial
detector
connected
to the PR
stre Serial
communication error (SUB) machine end
was disconnected.
NS2
No
signal
2
An
A,
B
or Z phase
error
was
detected
the
inclosed
loop
system.
PR
A
The
backup
vottage
in
the
absolute
position
detector
dropped.
last
ABSE Absolute position
be guaranteed.
The absolute position cannot
A power module error occurred
in the axis for which
the axis
NAE Not used axis error
PR
selection rotary switchis set to [Fl.
position detection The CPU in the absolute position linear scale connectedto the
A PR
sccpu Absolute
scale CPUerror(SUB)machineend
is notoperatingcorrectly.
The absolute position linear scale connected to the machine end
Absolute position
detectedaspeedof45m/sec.
or morewhentheNCpowerwasPR
(SUB)
turned ON.
The absolute position linear scale connectedthe
tomachine end
detection
Sabs qbsqlute
position
PR
a r w R error
(SUB)
detected
an
error
in the
scale or scalecircuit.
The absolute position linear scale connected the
to machine end
Rebtive position
detected a speed exceeding the scale's maximum movement
circuit error (SUB)
SDeed.
Sled
SDAT Scale data

STRE
os
'
i
Serial detector
communication error
Overspeed
An errorwas detected in the data storedin the EEPROMotthe

high-speed serial detector connected to the motor end.
Deterioration of the LEDs in the
high-speed serial detector
connected to the motor end was detected.
An error was detected at a position within
one rotation of the highspeed serial detector connected to the motor end.
Communication with the high-speed serial detector connected to the
motor endwas disconnected.
A speed exceeding the motor's tolerable speed was detected.
(Maximum motor speed x 1.2)
A
A
PR
PR
PR
PR
PR
module error
The IPM used the
by
inverter
detected
overcurrent.
an
PR
PMOC Power
(overcurrent)
NC communication CRC
Anerrorwasdetected in thedatasentfromtheNC
to the driver.PRC
DP
error
DE
NC communication Data error An error was detected in the movement command data from the NC. PR
NC communication
Communication
from
disconnected.
the
was
C
NCPR
Communication error
An illegal parameter
detected
was
parameters
in the
when
sent
PE
Initial parametererrorNCpowerwasturnedON.(Refertosection
(6) ErrorparameterNo.PRA
at initial parameter error)
TP1
~~o~mmunication
TP2
OC
NC communicati Protoc01e r r o ~2 An error was detected in the axis information data sent from the NC. PR A
PMO"
- r - - -
SLED EEPROMED error

error
SCPU Scale CPU
error
Overcurrent
Power module error
(averheat)
FE1
IFeedbackerror 1
FE2
Feedbackerror 2
An
error
was
detected
excessive
An current
was
detected
in the
communication
frame
sent
from
the
NC. PR
inmotor
the
drive
current.
APR
The IPM used byinverter

the detected
overheating.
A
PR
The feedback pulse was skipped

or a Z phase error wasdetected in
the Dosition detector.
Excessive deviation was detected in the feedback amount of the
motor end detector and machine end detector within the closed loop. PR A
An FB IC
error
was
detected
the
insemi-closed
1000.
I I
I11 - 57
4. Troubieshootina (MDS-C1 Series)
No.
Name
Abbr.
46
OHM
Motor overheat
50
OLl
Overload 1
51
OL2
Overload 2
52
OD1
Excessive error1
53
OD2
Excessiveerror 2
Details
RS
An error was detected in the temperature of the motor being driven.

NR
Or, the thermal protector built
in the high-speed serial detector
connected to the motorend activated.
The servomotor or servo driver load level obtained from the motor
NR
current reached the overload level set with the overload detection
level (svO22: OU).
A current command95% or more of the driver's maximum
NR
performance continuedfor 1 sec. or more.
The differenceof the ideal position and actual position exceeded
parameter SVO23: OD1 (or SVO53: 0 0 3 ) when the servo
was turned NR
ON.
The differenceof the ideal position and actual position exceeded NR
parameter SV026: OD2 when the servo was turned OFF.
The motor currentwas not flowing whenthe excessive error alarm1
NC
A
A
A
A
Servo warnings
No.
Abbr.
9o
wsT
Low-speed serial initial

communication error
91
WAS
L0W-S-d
serial
communication error
92
WAF
Low-speed serial protocol

error
93
WAM
Absolute
96
MPE
MP scale feedback error
97
MPO
MP scale offset error
Name
High-speed serialmultirotation counter error
9E
RS
Details
Initial communication with the absolute position linear was
scale
not PR
possible.
An error was detected in the communication with the detector
in the
*
absolute position detection system usingthe OHA25K-ET/absolute
position linear scale.
An error was detected in the data from the detector in the absolute
*
position detection system using the OHA25K-ET/absolute
position
linear scale.
Fluctuation exceedingthe tolerable valuewas detected in the
PR
absolute position detected when the NC power was turned ON.
Excessive deviationwas detected-inthe feedback amount of the.
*
motor end detector andMP scale In the MP scale absolute posltlon
detection system.
An error was detected in the offset data readin when the NC power
was tu&
ON within the MP scale absolute position detection
PR
system.
OSElO4/OSA104/OSE105/OSA105/OSE1W-F/OSA104ET/OSE105-ET/OSA105-ET. The absolute posltlon cannot be
*
guaranteed.
The voltageof the battery supplying to the absolute position detector
*
has dropped.
A level 80% of the overloadalarm 1 was detected.
*
WAB
Batteryvoitage drop
El
WOL
E3
WAC
E4
E6
E7
WPE
Overload warning
-lute
position counter
Deviation of the absolute position and relative position
was detected.
warning
Parameter error warning
A parameter exceedingthe setting range was set.
Control axis removal warningThe controlaxis is removed.
N C emergency stop
The NC is in the emergency stop state.
NCE
A
A
A
A
A
An error was detected in the multi-rotation counter of
9F
AXE
NC
A
A
*
*
A
A
(5) LED display No. at memory error
When a memory error (alarm

12) occurs, in most cases, a connection is not established with the NC.
If the connection is not established even when normally connected with the NC, check the servo
driver's LED display to see whether a memory error (alarm
12) has occurred.
The faulty section can be pinpointed according to the No. on
displayed
the LED at this time. (Refer to
the following table.)
Alarm display
Same display as other alarms
Only 12 and No. flicker on the

LED (Not connected withLED)
At servo driver powerON
At NC power ON
(6) Error parameter No. at initial parameter error
When an initial parameter error (alarm 37) occurs, the erroneous parameter is displayed on the NC
Diagnosis screen.
The display method differs according to each
NC, so refer to the respectiveNC Instruction Manual.
Normally the parameter No. (SVOOxx) is displayed at this time.

There is also a special 3-digitNo. (Refer to the following table.)
In this case, an erroris occurring for several parameters,so correctly set the related parameters.
No.
Details
The
maximum
rapid
traverse
rate
value
set
with the NC is incorrect.
69 This normally does not occur, but could be
caused by the NC system software.
71 The maximum cutting feedrate value set bythe NC is incorrect.
This normally does not occur, but couldbe caused by the NC system software.
The constants used by the following functionsare overflowing.
Electronic gears
Position loop gain
lol
Speed feedback conversion
Related parameter
NC axis parameter rapid
NC axis parameter clamp
svoo1 :PCl,SV002:PC2
SV003:PGNl, SVO18:PIT
SVO19:RNG1, SV020:RNG2
SV049:PGNl sp
Confirm thateach related parameteris correctly set.

Turn the absolute position detection parameter OFF.
connected detectoris an incremental specification detector,
so to carry out absolutesvol 7:SPEC, SV025:MTYP
02 The
position detection, exchange the detector withan absolute position specification
detector.
The sety option is not provided.
103 The optlon IS requlred for closed loop (including ball screw end detection) or dual
feedback control function.

servo option is not provided.
o4 The
The SHG control functionis an option.
105 The servo option is not provided.
The adaptive filter function is an option.
106 The servo option is not provided.
The MP scale absolute position detection function
is an option.
I11 - 59
~.
~~~~
SV057:SHGC
SV058:SHGCsp
SVO27:SSFl/aflt
SVOl7:SPEC/mp, mpt3
(7) Troubleshooting according to each servo alarm
[Alannlwarning checkperioq
f l : At servo driver power ON
f2: At NC power ON there after (emergency stop
ON)
f3: During normal operation (servo ON)
f4: During axis removal
(READY ON, sew0 OFF)
(Note) Warning "93"could occur wheninstalling the axis again after removing it once.
Alarm No.
12
Memory error:
Error in the drive unit memory
IC (SRAM or FLROM)
Investigation item
Confirm the repeatability.
Alarm check period

fl
f2
f3
f4
Investigation resub
Remedy
Always occurs.

2.

Check for abnormalities in the No special abnormalities were Replace the drive unit.
found.
An abnormality was foundin the Take measures accordingto the
noise, grounding)
confirm cooling fan
add -grounding measures.
I
I
Alarm No.
13
Software processing error:

The drive unit software data processing was not completed
within the normal time or an illegal
IT process was input.
I
Alarm check period

fl
92
f3
f4
0
0
0I
I
Investigation resutts
Investigation item
Changed
recently.
Not changed.
Remedy
2.
Confirm the repeatability. Atways occurs.

noise, grounding)

3.

found.
Ex. High temperature ...._
confirm cooling fan
.....
~larm
NO.
14
I Software
processing
error
2:
Of the driver softwareprocessing times, the current
loop
process was not completed within the set time.
1
I
Investigation item
Check whether theservo

software versionwas changed
recently.
Changed
Remedy
Not changed.
Confirm the repeatabillty.
Always occurs.


found.

noise, grounding)
Alarm No.
17

confirm cooling fan
N D convertererror:
Alarm check period
Anerroroccurred in thedriveunit's A/D converter.
s
I
Alarm check
period
I
Investigation
results
1Always occurs.
Investigation item
Confirmtherepeatability.
I
I

unit's peripheralenvironment.
(EX. ambient temperature,
noise,grounding)
ambient
peripheral
environment.

No specialabnormalitieswere
found.
Remedy
~~~~

cause.
confirm cooling fan
I11 - 61
-*~
,,
Alarm No.
18
3
4
Initial communication error:

Alarm check period
f4
Initial communication with the detector was not possible in af l
f3
f2
system using a high-speed serial detector at the motor end. 0
results
Investigation
Investigation item
Remedy
Correctly setSV025.
The valueis not correct.
Check thesew0 parameter
2.
Correctly connect.
Tug the connector to check
if the Disconnected (loose).
3.
detector connector (driver side Not disconnected.
and detector side) is
disconnected.
Turn the powerOFF and check Connection is defective.
with a tester
The alarmis on the unit.
Interchange with another normal
5.
axis drive, and check whether The alarmis on the detector.
the faultis located in the driver
side or detector side.
No special abnormalities were Replace the detector.
in tke
found.
An abnormallty was found
in the Take measures accordingto the
noise, grounding)
confirm cooling fan
I
Serial detector initial communication error

(SUB):
Alarm check,period
f4
Initial communicationwith the detector was not possible
in the
f2
fl
f3
system usingOHA25K-ET or a high-speed serial detector at the 0
machine end.
Investigation item
Remedy
Investigate the items for alarm
No. 'I18".
Alarm No.
1A
Alarm No.
1B
2
3
Alarm check period

CPU error (SUB):
An error was detectedin the data storedin the EEPROM of the fl f2
f3
f4
high-speed serial detector connected
to the motor end.
0
0
0
Remedy
.
Investigation
resub
Investigation item
Correctly connect.
Tug the connector to check if Disconnected
the
(loose).
absolute position linear scale
Not disconnected.
connector (driver sideand scale
side) is disconnected.
OFF and check Connection is defective. Turn the Replace
power the detector cable.
Connection is normal.
with a tester.
The alarm ison the unit. Interchange with another normal
axis drive, and check whether ThealarmoccurswiththePerforminvestigationitem
4.
the fault is located in the driver absolute position linearscale.
side or scale side.
Check for abnormalities in the No special abnormalities were Replace the absolute position
linear scale. found.
in the Take measures according to the An abno
noise, grounding)
confirm cooling fan
AIarm No.
1c
Alarm check period

EEPROWLED error(SUB):
The linear scale connected to the machine end detected an f l
f4
f2
f3
EEPROM error.
Or, deteriorationof the LEDs was detected in the high-speed
0
0
0
serial detector connected to the machine end.
Investigation item
Remedy

No. "1B .
Alarm No.
1D
Alarm check period

Data error(SUB):
An error was detected at a position within one rotation of the f l
f4
f2
f3
-
Investigation item
1
Remedy
The linear scale connected to the machine end detected an error

in the ROWRAM.
Or, the thermal protector built in the high-speed serial detector
connected
to
the machine end activated.
ROM-RAMI
(SUB):
error
thermal
;arihy;kfe[%

NO.Y B .
Alarm No.
1F
(SUB):
Serial detector communication error
Alarm check period
Communication with the high-speed serial detector connectedfl
to
f4
f3
the machine end was disconnected.
-
Investigation item
1
Investigate the itemsfor alarm

No. "1B .
Alarm No.
1E
Investigate the items2 and

following for the alarmNo. "18".
I11 - 63
Remedy
'
Alarm No.
21
Alarm check period

No signal 2:
An A, B or Z phase error was detected in the closed loop system.
Investigation item
:heck the servo parameter
:SV025)setting value.
Remedy
or
is set for the Correctly set.
parameter detector setting even
though the OHE-ET, OHA-ET
detector or various scale is not
connected.
"4", "5",
" 8 1
" 9 t
The settina is correct.

Tug the connector by hand to
Not disconnected.
side) is notloose.
~~

2.
Correctlv connect.
3.

4.
with a tester.
Redace the drive unit.
The alarm is on the detector. Perform investigation item
5.
No special abnormalities were Replace the motor (detector).
in the
found.
An abnormalltywas found in the Take measures accordingto the
noise, grounding)
ambient peripheral environment.Cause.
confirm cooling fan
.....
~~
Alarm No.
, I
lost:
position
Absolute
!aj&;hr!er!
This occurs when the power
in the absolute position detector is
lost, and will return to normal when the unit's
2OOVAC is reset
and zero mint return is Derformed aaain.
Investigationitem
~~~~
I
~~
Investigation
resuns
~~~
Check whether the absolute

Was disconnected.
position detector cable (includingGuideline:
At delivery:
battery connection cable)
was left
disconnected for a while.
20 hours or more
After 5 years:
10 hours or more
I Was not disconnected.

Check whether a battery error
Remedv
Reset the drive unit's

2OOVAC
power and perform zero point
return again.

Check the batten, voltaae.
Alarm occurred.
Did not occur.

Tug the detector connector (unit Was disconnected (loose).
Correctlv connect.
and detector side) to
see if it has was not disconnect&
disconnected.
Also check the cable between
the battery unitanddriveunit.
Turn the power OFF and check A connection defect was found.
I1

Does not recur.
Perform zero point return again.

if there is no error, continue to
use.
~~
Always recurs.
I Thealarmisontheunit.

noml axis unit and check
detector
or
side
side.
I
found.
noise, grounding)
ReDlace the drive unit.

~~~
~~~

cause.
confirin cooling fan
~.
~

, .
Alarm No.
27
I
I
Scale CPU error:

;arihjcTT;{
The CPU in the absolute position linear scale connected to the
machine
end
operating
correctly.
is not
-
Investigation item
1 Tug the connector to check
if the
absolute position linear scale
connector (unit side and scale
2
OFF and check
with a tester.
I whether the defectis on the unit
I
- side or scale side.
4 Check for abnormalities in the
noise, grounding.)
Alarm No.
28
Is disconnected (or loose).
Not disconnected.
1
I
Remedy
Correctly connected.

Connection is faulty. Turn the power
Connection is connectReplace the drive unit.

The alarm occurs with the
absolute Dosition linear scale.
No special abnormalities were Replace the absolute position

linear scale.
found.
An abnormality was found in theTake measures accordingto the
confirm cooling fan
...
add aroundina measures.
Alarm check period

Scale overspeed(SUB):
The absolute position linear scale detected a speed of 45m/sec.
fl
f2
f4 f3
or more when the NC power was turned ON.
0
-
Investigation item
Remedy
Set the SV025: MTYP parameter
Check the absolute value linear The specifications are not for the
scale specifications.
Correctly.
The specifications are for the Perform investigation item2.
Check the motor mechanical
Is moving.
Check whether the machine was
brakes and machine system.
operating when the alarm
occurred.
Is not moving.
Correctly connect.
Tug the connector
to check if the
Was disconnected (loose).
absolute position linear Scale
Was notdisconneed.
with a tester.
whether *e defect is on the unit absolute position linear scale.
Check for abnormalities in the No special abnormalities were Replace the absolute position
found. linear scale.
noise, grounding)
Ex. High temperature ._...
confirm cooling fan
...
I11 - 66
Alarm No.
29
Absolute position detection circuit error (SUB):

Alarm check period
The absolute position linear scale connected to the machinefl
end p2
f4
f3
detected an error in the scale or scale circuit.
0
0
0
Investigationstem
No."28".
Remedy
Alarm No.
2A
Relative position detection circuit error (SUB):

Alarm check period
The absolute position linear scale connected to the machinefl
end p2
f4
f3
detected aspeed exceeding the absolute position linear scale's
0
0
0
maximum movement speed.
Remedy
Investigation item
I
The machine was operating.
Check whether the machine was
operating when the alarm
The machine was not operating. Perform investigation item2.
OCCUTTed.
Check whether movement is
Is moving
Is not moving
before turning the powerON.
Check the wiring
Correctly
I
Tug the connector
tocheck if the Was disconnected(loose). connect.
absolute position linearscale
side)is disconnected.
I
A connection defect was found. Replace the-detector cable.
Turn the p o w e r OFF and check
with a tester.
Replace
drive
unit.
the
I
I Tw c o n n a n a with another
I Thealarmisontheunit.
normal axis u h and check
absolute position linear scale.
side or dewor side.
No special abnormalities were Replace the-motor (absolute
Check for abnormalities inthe
position linear scale).
found.
unifs peripheral environment.
noise, grounding)
Ex. High temperature ..... .
confirm cooling fan
...
I1 !
2
II
II
4
I5
Alarm No.
2B
eck
~~
~~
CPU error:
An error was detected in the data stored in theEEPROM of the
~-
Inveitigation item
Investigate the items 3 and
followina for the alarmNo. "2A'.
Alarm No.
EEPROMILED error:
An error was detected in the
EEPROM of the high-speed serial
detector connected to the motor end.
Investigation item
following for the alarmNo. "2A".
PC
~~~~
I11 - 67
Remedy
Alarm check period

f4
f3
fl f2
0
0
0
Remedy
Alarm No.
error:I Data
check
Alarm
An error was detected at a position within one rotation
of the
2D
I
I
I
Investigation item
1
error:
Alarm
check
Communication with the high-speed serial detector connected to
the motor end was disconnected.
Remedy
Alarm check period

Overspeed:
A speed exceeding the motor's tolerable speed was detected. fl
f3
f4
(Maximum motor speedx 1.2)
0
0
0
Investigation item
Is the machine moving during theIs not moving

alarm?
Is moving
Check whether movement

is
Check whether the rapid

traverse rateis too fast.

3.
Is moving
Is not moving

before turning the powerON.
Is too high.
Investigate the items

2 and
following for the alarm
No. "18.
...
Check the wiring

Correct tobelow the rated speed.
4.
Lower the rapid traverse time
constant so that the current value
during rapid traverse
acceleration/decelerationis less
than 8OYo of the maximum value.
5.
I11
e
Remedy
2.
Is set to below the rated

speed.
80% or more of the maximum
Check whether the time constant
value is displayed.
is too low.
Check the current value
displayed on theservo
monitor Screen.
The setting is less than80% of
the maximum value.
"
period

following for the alarm
No. 11181'.
Alarm No.
31
-.
Remedy
I Serial
detector
communication
Investigation item
Investigatethe items 3 and

following for the alarmNo. "2A".
Alarm No.
2F
period
- 68
,._"
Alarm No.
32
Power module error (overcurrent):

The IPM used by the inverter detected an overcurrent.
Alarm check period

fl
f2
f4 f3
-
Investigation item
1
U, V, W phases on the Short-circuited, or not Are the

unit output short circuited.
energized.
Disconnect theU, V, W wires .
from the terminal block and Normal.
the motor cannon plug and
check betweenU, V, W with
a tester.
h
:e
c
kthe U, V, W wires
Remedy
Replace the U, VI W wires.
for a Short-circuited, or not

p u n d fault.
energized.
Check between theU, V, W Normal.
wires and grounding with a
tester in the itemIstate.
Replace theU, V, W wires.
or not
:heck for a motor ground fault.
Check between theU, V, W energized.
wires and grounding
with a
Normal.
mqger tester in the
(Same level as other axes)
Replace the motor. Short-circuited,
State.
~~~~
>heck the servo parameter The settings are incorrect.

setting values.
The settings are correct.
procedures.
Correctly set.
Tug the detector connector (unitWas disconnected (loose).

3nd detector side) to
see if it has
not disconnected.
lisconnected.
rum the powerOFF and check A connection defect was found.
e
' detector cab' mnnecfjon
' Connection was normal.
with a tester.
Does not recur.
Correctly connect.

noise, grounding)

Recurs Deriodicallv.
Always recurs.

No special abnormalities were Wait.

found.
confirm cooling fan

...
I11 - 69
....* "
- .. .
Alarm No.
34
NC communication CRC error:

Alarm check period
in the data sent from the
NC to the driver. fl I 42 I f3 1 f4
0
0 1 0
I
Investigation item
Tug the connection connectors The connectors are

between the NC and drive unit, disconnected (loose).
battery unit and drive unit, and
Not disconnected.
between drive units to
see if they
are loose. Check that an
excessive force is not being
applied on the connector section.
Remedy
Correctly connect.
Turn the powerOFF and check A connection defect was found. Replace the communication
cable.
the connection of the
communication cable in item1
with a tester. Try replacing with a
normal cable.
C h k k whether the NC and drive Was changed.
software version.
unit software version was
recently changed.
Not changed.
The alarm is on the unit side. Replace the drive unit.
Replace with another normal
unit, and check whether the errorThe driver is not the cause. Perform investigation item5.
is on the NC side or unit side.
Check for abnormalities in the No special abnormalities were Replace the MCP card on the NC
found.
side.
to the
An abnormality was found in the Take measures according
noise, grounding)
ambient peripheral environment. Cause.
confirm cooling fan
...
~~
Alarm No.
An
in the
movement command data from the
35 communication
NC error was detected
Data
error:
yr;hryT;:
NC.
~~
~~
36
Investigation item
Investigate the items for
alarm
No. "34".
Alarm No.
NC communication Communication error:

Communication from the NC was disconnected.
Remedy
Alarm check period

f2
f4 f3
fl
Investigation
item

No. "34".
Remedy
Investigation
results
Alarm No.
Initial parameter error:

Alarm check period
An illegal parameter was detectedin the parameters sent when fl f2
f4
f3
the NC power was turnedON.
0
0
Investigation item
Remedy
illegal parameter No. is
The settingis incorrect. The
Set the correct parameter.
displayed on the NC diagnosis The setting is correct.
screen, so adjust the servo
The DarameterNo. is other than Perform investiaation item2
parameter with the parameter 11 to&.
when paramet& No. is 101.
adjustment procedures.
Check whetherthe servo
Illegal or setting range is
Refer to the parameter settings
parameter (PIT) (RNG1) (RNG2) exceeded.
and supplementary explanations
(PC1) (PC2) combination is
in the specifications, and reset to
illegal, or whether the setting
the correct value.
The settingis correct.
range hasbeen exceeded.
Check the items for alarmNo.
37
Alarm No.
NC communicationprotocolerror 1:
Alarm check period
in the communication frame sent from the
fl f2
f3
f4
NC.
Investigation item
investigation results
Remedy
Investigate theitems for alarm
No. "34".
Alarm No.
NC communication protocol error2:

Alarm check period
An error was detectedin the axis information data sent from thef l
f2
f4
f3
NC.
- ' O 0
0
Investigation item
investigation results
Remedy
No. "34*.
39
1
L
Alarm No.
3A
1
Overcurrent:
An excessive current was detected
in the motor drive current.
Investigation item
Alarm No.
36
1 Power module
loverheat):
error
The IPM used byi&erter

thedeiected
overheating.
Investigation Item
environment
1) Rotation of fan on rear of
The fan is not rotating correctly.
unit
Alarm check period

f2
fl
f3
f4
0
0
0
Remedy
Remarkable amountsof cutting

radiating fins.
55C is exceeded.
ambient temperature
in the The grounding is incomplete.
noise, grounding)
No particular problem.
111 - 71
Alarm
check
Deriod
fl
-
f2
0
f3
0
f4
0
Remedy
Replace the
fan
I Take measures
to prevent cutting
Clean the fins oil or dust from
contacting the
fins.
Correctly ground.
Take noise measures for the Alarms occur e
device on theleft. certain device operates.
Alarm No.
42
Feedback error1:
The feedback pulse was skipped or Zaphase error was
detected in the position detector.
Investigation item
Investigate items 3 and following
for alarm No. "21".
Alarm check period

fl
42
f4
f3
Remedy
Alam No.
Feedback error2:
Alarm check period
Excessive deviation was detected in the feedback amount off l the f2
f4
f3
motor end detector and machine end detector within the closed
0
0
loop.
An FB IC error was detected in the semi-closed loop.
Investigation item
Remedy
Investigate items 3 and following
for alarm No. "2A".
43
Motor overheat:
Alarm check period
An errorwasdetectedinthetemperatureofthemotorbeing
f l I 42 I f3 I f4
driven.
Or,thethermalprotectorbuilt
in thehigh-speedserialdetector
0
0
I connected to thema 3r end activated.
Investigation item
Remedy
Recurs within one minute start
of
UPRecurs periodically after
2.
operating for some time.
The motoris hot.
Lessen the operation pattern.
1
If the problemis not solved,
The motoris not hot.
The connectors are
Tug the detector cable
Correctly connect.
connectors (unit side and motor disconnected (loose).
side cannons) tosee if they are Not disconnected.
Perform investiggtion item 4.
loose.
with a tester.
If the thermal connection is as No conductivity or large
Replace the motor or detector.
shown below for OSEl04/105 resistance in the motor and
and OSA104/105,so cut the wire detector thermal.
between the motor and detector
with a joint amplifier, and check
the thermal conductivity for each.
46 NoA'ann
I-I I I
~~~
Replace with another normal axis

The alarmis on the unit side.
Replace the unit.
unit, and checkif the defect is on Occurs evenif unit is replaced. Perform investigation item7.
the unit.
An abnormallty was found in theTake measures according to the
noise, grounding)
Ex. High temperature ..._.
confirm cooling fan
...
I11 - 72
Alarm No.
1-
I Overload 1:
Alarm check period

The servomotoror servo driver load level obtained from the
motor current reached the overload level set with the overload
I detection level (SV022: OLL).
Investigation item
Remedy
The setting is not the standardCorrect to the standard setting
(OU) (OLT) setting values.
setting value.
Standard setting values
OLL: 150
not being used.
~~~~~
The value is the standard settingPerform investigation item2.

value.
~
~~

The motor is hot.
Ease the operation pattern.

3.
Check whether the motor
is
hunting.
Hunting is occurring.

3.
procedures and readjust.
Check the cable wiring and
connector connections.
Check for mistaken
parameter settings.
Adjust the gain.
L
4.
Hunting is not occurrina.

Replace with another normal axisThe alarmis on the unit.
defect is on the unit.
unit is replaced.

4.
Check whether the current value

The value is abnormal.
displayed on theNC Servo
The value is correct.
Monitor screenis abnormally
large when stoppedor during
operation.
Check the machine system.

unirs peripheral environment.
(Ex- ambient temperature,
noise, grounding)

found.

5.
6.
An abnormality was found in theTake measures according

to the
confirm cooling fan

...
I11 - 73
-
-UP_..
.,
Alarm No.
51
~~
A current command95% or more of the driver's maximum

performance continued for1 sec. or more.
Overload 2:
~~
Investigation item
Check whether the PN poweris The voltage is supplied.
being supplied to the driver.
Check the axis for which the
alarm is occurring and the
axis farthest from the power
supplythe PN
is no voltage at
unit CHARGE lamp is lit and
check the PN terminal voltage. There is a voltage at the PN
1 yy;hy;ejri;: 1
-
Remedy
2.
Check the power supply unit. There

terminal. units.
The maximum value exceeds the
Lengthen the acceleration/
Check whether the current value
deceleration time constant, and
level indicatedwith an x in the
displayed on the NC Servo
lower to80% of the limit value.
Monitor screen is abnormally
table on the previous page.
large during acceleration/
A correct value is displayed.
deceleration.
for alarmNo. "50.
~~~
~~
~~
. Alarm check period

Excessive error I:
Thedifferenceoftheidealpositionandactualpositionexceeded
f3
f4
'
parameter SV023: OD1 (or SV053: 0 0 3 ) when the servo was
0
turned ON.
Investigation item
Remedy
is supplied.
Perform investigation item 3. The voltage
Check whether the PN power is
being suppliedto the driver.
PerForm investigation item2.
The voltageis not SUPPlidalarm is occurring and the
supplyThere isthe
no vottage
at the unit.
PN
Confirm that the power supply Check
power suppljr
unit CHARGE lamp is lit and terminal. (The lampis not lit.)
check the PN terminal voltageCheck the PN wiring between the
There is a voltage at the PN
terminal.
units.
The setting is not the standard Correct to the standard
Checktheservoparameter
specification valueif special
setting value.
specifications are not being used.
setting value.
Alarm No.
52
fl
I11 - 74
lsupplementary explanation
I
The actual machine position deviated an amount exceeding the value set in OD1 from the ideal
machine position for the command position.
This will occurif the actual machine position enters the shaded area shown below.
Command positic
\
Position
OD 1
OD 1
servo OFF
>
Time
Servo ON
I11 - 75
___L
..
Alarm No.
53
error
The
difference of
Excessive
2: the ideal position and actual position exceeded
rajrn;hT;3pr;:
parameter SV026: OD2when the servo was turned
OFF.
I
Investigation item
:heck the servo parameter
lOD2) setting value.
:heck if the machine is moving Is moving.

juring sew0 OFF.
Is not moving.
Not disconnected.
Turn the powerOFF, and check A connection defectwas found.

the communication cable
Try changing with a normal
cable.
Replace with another normal axisThe alarm is on the unit.
defect is on the unit.
unit is replaced.
____
Tug the detector cable connectorIs disconnected ( l o o s e ) .

(unit side and motor side cannon)
Not disconnected.
to check ifit is disconnected.
Turn the powerOFF, and check
with a tester.
noise, grounding)
Remedy
The setting is not the standard Zorrect to the standard setting
lalue if special specifications are
setting value.
lot being used.
setting value.
Tug the communication cable

zonnector from the NC to the
terminator (unit side and NC
side) to see if it is disconnected.
'erform investigation item2.

:heck the machine and
nechanical brakes.
>erform investigation item
3.
Zorrectly connect.
3erform investigation item4.
=able.
Replace the NC side MCP card.
1
If the problem is not
solved,
Correctly connect.
7.
A connection defectwas found.
Not disconnected.

8.
No special abnormalities were Replace the motor.

found.
An abnormallty was found in the Take measures according to the
confirm cooling fan
...
Alarm No.
54
Excessive error3:
Alarm check period
The motor current was not flowing when the excessive error f l
f4
f2
f3
alarm 1 was detected.
0
0
Investigation item
Remedy
Check whether the PN power isThe voltage is supplied.
being supplied to the driver.
alarm is occurring and the
supply.
Check the power supply unit. There is no
unit CHARGE lamp is
lit and
check the PN terminal voltage. There is a voltage at the PN Check the PN wiring between
the units.
terminal.
Increase the acceleration/
Check whether the motor powerThe power wire is not connected
deceleration time constant, and
wire is connected to the motor. or the power wire is broken.
lower to approx.80% of the limit
Disconnect the power wire
value.
from the terminal block, and
check between the UVW
The power wire is correctly
wires with a tester.
connected.
Replace the motor.
The alarm ison the motor.
I
f3
f4
1 error was detected during the
GO
fl
f2
A collision detection type
modal (rapid traverse).
0
(A disturbance torque that exceeds the external disturbance torque was detected.)
Investigation
Investigation
item
results
Remedy
Is the collision detection function The collision detection function Perform investigation item2.
is not used.
being used?
Check whether the machine has
The machine has collided.
not collide.
collided.
The collision detection function Perform investigation item 3.
not
machine
has
the
I isbut
used,
I
I
collided.
Change SV060 (TLMT) to"0".
Check the parameters.
Is SV060 (TLMT) set to"O"?
Check whether the current has The current is90% or moreof
or 90% of the limit value during The current is less than
90% of Perform investigation item4.
normal rapid traverse
Adjust the collision detection

The alarm occurs.
specifications.)
Does the machine or current Is vibrating.
vibrate?
Try increasing the detection
Is not vibrating.
level.
The alarm occurs.
I11 - 77

If the problem is not solved by
the level.
4. Troubieshootina (MDS-C1 Series)
Alarm No.
59
Collision detection1:
Alarm check period
A collision detection type1 error was detected during the
G1
f3
f4
f2
fl
modal (cutting feed).
(A disturbance torque that exceeds the external disturbance 0
torque was detected.)
Investigation item
I I
I I
2
Remedy
The collision detection function Perform investigation item2.
is not used.
Check whetherthe machine has The machine has collided.
collided.
not collide.
The collision detection Gnction Perform investigation item3.
is used, butthe machine has not
collided.
~~
Checktheparameters.
Is SV060 (TLMT) set to"OH?
~~~~
I'
Thesetting is incorrect.
1
I
Change SV060 (TLMT) to "0".
I
I

performinvestigationitem 4.
or 90% of the limit value during The current is less than 90h of Perform investigation item 4.
normal cutting feed
~occur.
not
does
The alarm
I
I
Adjust the collision
detection
The alarm occurs.
specifications.)
Is vibrating.
5 Does the machine or current
vibrate?
3 Check whether the current has The currentis 90h or more of
~~
6 Try increasing the detection

level.
Alarm No.
SA
The alarm does not occur. If the problem

is not solved by
replacing the unit,try increasing
the level.
The alarm occurs.
Collision detection2:
A collision detection type
2 error was detected.
Investigation item
Remedy

No. "58".
Alarm No.
60 to 7E
Power supply alarm:

An alarm is occurring in the power supply unit.
investigation item
1
~~~
Is not vibrating. Perform investigation item 6.
11
1
~~
MDS-C1 -CV
Refer to the power supply
sDecifications.
Alarm check period

fl
-
f2
f3
f4
Remedy
No.
A
I
-
Amplifier power reset request:

Alarm check period
An error was detected when the control mode (high gain mode,
f4
standard mode) was selected.
Or, an error was detected in EEPROM
the
if this error is detected
again after the power is reset.
7F
-1
fl
investigation item
Confirm the repeatabillty.
2 Check for abnormalities inthe

noise, grounding)
Alarm No.
Always occurs.


found.

confirm cooling fan
-
check
I Alarm
The servodrive software process was not executed within the
designated time.
Investigation item
Check whether
the
servo
:software version was changed
Irecentty-
Remedy
I Watch don:
I
I
Investigation
results
I It was
changed.
I
Remedy
I Try
returning
the
original
to
period
software version.
Not changed.
~

peripheral environment.
noise, grounding)
Iunit's

found.
confirm cooling fan
Grounding not enforc
ed.....
I11 - 79
,.. ...,
_",
4. Troubleshootina (MDS-C1 Series)
HR unit connection error:

Alarm check period
f4
f2
f3
Incorrect connection or disconnection
of the MDS-B-HR
fl
connected the machine end was detected.
0
0
0
Investigation item
Remedy
Correctly connect.
Tug the connector to checkthe
if Is disconnected (loose).
MDS-B-HR connector (unit side, 1s not disconnected.
2.
HR side and linear scale side)
is
disconnected.
- 1
Turn the power OFF and checkThe connection is defective.
the connectionOf the detector
cable (between driver and
I/F
I
I
I
unit, and and
between I/F unit
scale) with a tester.
Alarm occurs in unit.
Interchange with another correct
axis unit (Or MDS-B-HR), and
4.
Alarm occurs in MDS-B-HR
check whether the faulty section
(linear scale).
is in the unitor MDS-B-HR
(linear scale).
Check for abnormalities in the No special abnormalities were Replace MDS-B-HR (linear
found.
scale).
to the
An abnormality was found
in the Take measures according
noise, grounding)
confirm cooling fan
...
Alarm No.
~~
~~
~~
HR unit HSS communication error:

Alarm check period
The MDS-B-HR connected to the machine end detected an ferror
l
f2
f3
f4
in the communication with the absolute position linear scale. 0
0
0
Investigation item
Remedy
1 Investigate the items for alarm
I No. "89.
I
I
Alarm No.
8A
HR unit scale judgment error:

The MDS-B-HR connected to themachineendcould
the connectedscale's analog wave cycle.
Remedy
investiaation results
lnvestiaation
item
Correctlv connect.
I s c o n n e c t e d (Ioose).
MDS-B-HR connector (unit side, Is not disconnected.
HR side and linear scale side)
is
disconnected.
Turn the power OFF and check The connectionis defective.
the connectionof the detector
cable (between driver andI/F
unit, and between I/F unit and
scale) with a tester.
Interchange with another correctAlarm occurs in unit.
axis unit (or MDS-B-HR), and
Perform
Alarm occurs in MDS-6-HR
check whether the faulty section
(linear scale).
is in the unitor MDS-B-HR
(linear scale).
No special abnormalities were Replace MDS-B-HR (linear
Check for abnormalitiesin the
found.
scale).
An abnormality was found
in the Take measures according
to the
noise,
grounding)
confirm cooling fan
...
add aroundina measures.
8C
Ala-No-
II
111 - 80
A
a
ln No.
80
I HR unit CPU error:
I The CPU forthe MDS-B-HR connectedtothemachineendis

I not operating correctly.
Deriod
check
1 Alarm
' fl
1
0
-
f2
-
f i
I
f4
1
Investigation item
I
Investigation
results
Remedy
Tug the connector
to check if the Is disconnected (loose).
Correctly connect.
MDS-B-HR connector (unit side Is not disconnected.
and HR side) is disconnected.
Turn the powerOFF and check The connection is defective.
the connection of the detector Connection is normal.
cable (between driver andI/F
unit) with a tester.
Interchange with another correct
Alarm occurs in unit.
axis unit, and check whether theAlarm occurs inMDS-B-HR.
faulty section isin the unitor
MDS-B-HR.
No special abnormalities were Replace MDS-B-HR.
found.
An abnormality was found in theTake measures according to the
noise, grounding)
confirm cooling fan
...
Alarm No.
HR unit data error:

Alarm check period
An errorwas detected in the analog interpolation data for the f l
f4
f2
f3
MDS-B-HR connected to the main side.
0
0
0
Investigation item
Investigation resub
Remedy
No- "89.
8E
Ahrm No.
90
Low+peed serial initial communication error:

Initial communication with the absolute position linear
scale was
not possible.
Investigation item
No. " 5 8 .
Alarm No.
91
I
1
Low4speed serial communicationerror:

An error was detected in the data from the detector in the
absolute position detection system using the
OHA25K-ETI
absolute position linearscale.
lnvestiaation
item
I
I
Alarm check period

f4
fl p2
f3
0
Remedy
Alarm check period

f4
fl
f2
f3
-
Remedv
Investigate the items-3and

foliowing for alarm No."251
Alann No.
92
Low-speed serial protocol error:

An error was detected in the data from the detector in the
absolute position detection system using the
OHA25K-ET/
absolute position linearscale.
Investigation item
Inveswate the items 3 and
following for alarmNo. "25"
I11 - 81
Alarm check period

fl
f4
f2
f3
-
Remedy
rive
Alarm No.
Alarm check period

Absolute position fluctuation:
f4
f3
Fluctuation exceeding the tolerable value
was detected in the
fl
f2
- 0
absolute position detected when the NC power was turned ON.
Investigation item
Remedy
Correctly connect.
1 Tug the connector to check if The
the connectors are
detector connector (unit side
disconnected (loose).
and detector side) is
2.
Not disconnected.
disconnected.
Check the cable between the
unit battery
same time.
2 Turn the powerOFF and check Connection is defective.
the detector cable connection Perform
investigation
item
3.
Connection
is normal.
with a tester.
Perform investigation item5 ,
The erroris not repeatable.
3 Check the repeatability.
and connect and use if there
is
Carry out zero point return
no abnormality.
again.
The error is always repeated, orPerform investigation item 4.
the state is recovered once, but
the error is repeated.
The alarm is on the unit side. Replace the unit.
4 Replace with another normal axis
5.
unit, and checkif the defect is onOccurs evenif unit is replaced. Perform investigation item
the unit.
5 Check for abnormalities in the No special abnormalities were Replace the motor.
found.
An abnormalitywas found in the Take measures according
- to the
cause.
ambient
peripheral
environment.
noise, grounding)
confirm cooling fan
...
93
and
I I
Alarm No.
96
MP scale feedback error:

Alarm check period
Excessive deviation was detected in the feedback amount off l the f2
f4
f3
motor end detector and
MP scale in theMP scale absolute
0
0
0
position detection system.
Investigation item
Remedy
Investigatethe items 3 and
following for alarmNo. "25'
Alarm No.
97
1
b
IMP scale offset error:

Alarm check period
Excessive deviation was detected in the feedback amount offl
the f2
f4 f3
motor end detector and MP scale in the MP scale absolute
0
position detection system.
Investigation item
Remedy
following for alarmNo. "25"
Alarm No.
9E
An error was detected in the multi-rotation counter with the

high-speed serial detector connected to the motor end and ball
0
0
High-speed
screw end. serial multi-rotation
counter
error:
Fr;hrF3pT;f
Investigation item
Remedy
following for alarm No."25'
Alarm No.
SF
Battery voltage drop:

Alarm check period
f2
f4 f3
The voltage of the battery supplied to the absolute position f l
detector dropped.
0
0
0
Investigation item
Remedy
Check the battery unit voltage.
Replace the battery. The battery voltage ha
There is no error in the battery Perform investigation item2.
voltage.
Investigate the items
3 and
following for alarm No. "25l
Alarm No.
El
Overload warning:
An 80% level of the overload
1 alarm was detected.
Alarm check period

fl f2
f4 f3
-
Investigation item
Check whether the motor is hot.
Remedy
"50".
if there is an error
when
acceleration/ deceleration is
performed.

2.
The motor is hot.
1. If the operation pattern canbe
Operation is possible without Check
eased, ease it. error.
2. If operation is possible without
an alarm occurring, continue
use.
Operation is abnormal.
for alarm No."50'.
Alarm No.
Absolute position counter warning:

Alarm check period
f2
f4 f3
fl
Deviation of the absolute position and relative position
was
detected.
0
0
Investigation item
Remedy
Check the battery
voltage,
Occurs whenNC power is turned Investigate
the state
where the
ON.
warning occurred.
perform zero point return, and
then turn powerOFF and ON.
"25'.
Occurs during operation.
Check the batterywoltage. An alarm occurre
Check whether a battery error
Check the detector and cable.
Did not occur.
E3
Alarm No.
E4
Parameter error warning:

A parameter exceeding the setting range was set.
Alarm check period

fl
f2
f4 f3
-
Investigation item
Set the correct value according to
the parameter adjustment
procedure.
Alarm No.
Remedy
NC emergency stop:
Alarm check period
f3
f4
f2
signal
is being sentfrom the NC or an alarm fl
axis.
0
0
0
Remedy
Emergency stopis activated.
Emergency stopis released.
The machinestarts up normally. Normal
"E7" is still displayed.
Check if a terminator
or battery
Correct the abnormality.
Abnormal place found
unit is connected or if
Normal
"34".
disconnected.
E7
An emergency stop
occurred in another
Investigation item
Check if the NC side emergency
stop switch is activated.
Release the emergency stop.
I11 - 83
5. Appendix
5. Appendix
5.1 Changing from closed loop to semi-closed loop
To move the axis with the semi-closed loop for troubleshooting due to a defect in the closed toop or for
temporary operation, changeover with the following procedure.
1. Leave the parameter SVOI7 SPEC bit 5 setting as it is, and change the other bits to
0.
2. Set parameter SVOl9RNGI according to the motor shaft end detector type.
HA053/13
For
10
Forothermotors100(Motorenddetector
: OHA25K,OHE25K, OSAl04,OSEl04)
1000 (Motor end detector : OSAlO5, OSElO5)
3. Set parameter SV020 RNG2 to the same value as SVO19 RNGl .
4.
Leave the lower 8-bit of parameter

SV025 MTYP as is, and change the upper 8-bit as shown below.
ForHA053/1333xx
For othermotors
(xx is thesamesettingasthelower8-bit)
OOxx (xx is thesamesettingasthelower8-bit)
Motor end detector: OHE, OSE type

1l x x (xx is the same setting as the lower 8-bit)
Motor end detector: OHA, OSA type
5. Turn the NC power OFF andON and confirm the axis movement.
6. Confirm the backlash amount,1 pulse response, and overshooting duringacceleration/deceleration,
and change the compensation amounts
if necessary.
Note 1) Write down the parameter data before changing

so it can be applied when returning to closed
loop.
Note 2) Always perform set the reference point again when returning to the closed loop in the
absolute position detection system.
I11 - 84
~,.._.
-.
_-._-
5. Appendix
Parameters p e r servo system

Relative position detection
Para
loop
Absolute position detection
Closed loop
Ball screw end

detection
Closed loop
detection
bit7=l
~~
I
100
Ball screw pitch
(OHE25WOSE104) .....................................
..........................................................................
o
l
t
0
0(OSEIoa
o
l
t
o
o (OSE105)
Scaleresolution
100
(OHA25WOSA104)
......................................
1OOO (OSA105)
10 (HA053/13)
10 (HA053/13)
.....................................
.....................................
svo20 Samesettingas
RNG2 mol 9
100
Same settingas
(OHE25WOSE104)
(OHE25WOSE104) svol9
.................................... .....................................
100
lo00 (OSE1050)
lo00 (OSE1050)
O0
~~~~&~
/OR
1OOO (OSA105)
Scale resolution
lo00 (OSE105)
lo00 (OSE105)
93WA3xx
l
x
x
(HA053/13) (HA053/13)
.....................................
...............................
...... .....................................
............................................................................
( 0 ~ 5 ~ 0 ~ ~ 1 0 4 )
ooxx
4ow6oxx
8oXX
50W60XX
SO>ovAOXX
......................................
(oHE~~WOSEI
04) (OSE25WOSE104) (OHE25WOSE104)
(OHE25WOSE104) (OHE25WOSE104)
............................................................................
h....
.....................................................................
I.....................................
22xx (OsA105)
92>OvA2>0<
52>Ov6=
(OSE105)
(OSE105) (OSE105)
hl myp I
m25
Ball screw pitch

....................................
10 (HA053/13)
10 (HA053/13)
............................................................................
100
100
(OHE25WOSE104) (OHE25WOSE104)
............................................................................
53w63xx
bit7=l
~~~
.10
.......(HAOW1
......................3)
......
Detector
Is2xx
The l v , 0.lp.m changeover is performed with the NC parameters.

(When using HA053/13,0.1pmcannot be used.)
111 - a5
~~
Amplifier
Capacity
Confi guration
System
Detector
Motor enddetector
Servo amplifier
Type
Motor
or OHE25K-6
HA40N
OSE
10410SE
105
more
MDS-AB-V1-
HA23N'OHE25K-85
OSEl04SIOSE105S
HA33N
Low inertia
OHE25K-108
OSEl04S/OSEl05S motor
MDS-NB-V2-0
HA053
Built-in encoder
Machine end
detector
E l
Motor shaft enddetector

Max. tracking capacity:
5MPPS
Min.
resolution
: 0.0036'
speed
Max.
: 3000rpm
1
I
I OHE25K-6
lml
Motor shaft end detector

5MPPS
Min.
resolution
: 0.0036'
Max. speed
: 3000rpm
u-
MDS-AIB-V2-0
Q
0
0
CN2
OHE25K-ET
OSEl04ET
OSAl04ET
CN2
IHA40N
CN3
/061104/0SE105
MDS-AB-VI-0 OHE25K-85
1 1
I
or
I Connection of various
mz3N
scales with a 1p
specification, 0 . 5 ~
OSEl04S/OSElO5S
HA33N
specification
pulse
FIB
CN2
OHE25K-108
inertia
possible.
Low
(Ex. MP
scale
OSEl04S/OSE105S
motor
MDS-AIB-V2-0
(Mitsubishi
HA053
Heavy
Built-in encoder
Industries))
orOHA25K-4
HA40N
MDS-NB-V1-0 OSAl04/0SA105 Imore
HA23NOHA25K-85
OSAl04S/OSAlO5S
HA33N
CN2
CN3
Motor shaft detector

end
5MPPS
Min.
resolution
: 0.0036"
: 3000rpm
Max.
speed
MDS-NB-V2-0 OHA25K-108
inertia
Low
I OHE25K-6
HA053
I OHE25K-6
MDS-AB-VI-0
Max. tracking capacity

(according to maker)
Min. resolution
(according to maker)
FIB cable 1
Motor Machine
end
end
l-
Motor shaftdetector
end
5MPPS
Min.
resolution
: 0.0036'
: 3000rpm
speed
Max.
I OHE25K-6
0.83MPPS
Min.resolution : l p
Max.
speed
: 50mlmin.
1 I
IHA40N or I
OSEl0410SE105
mG3N
MDS-NB-V1-0
OHE25K-85
OSEl04SIOSEl05S HA33N
OHE25K-108
Low
inertia
MDS-AB-VI-0
OSE10410SE105
more
OHE25K-85
. .. ..IHA40Nor
OHA25K-ET
OSAl04ET
OSAl05ET
CN3
HA23N
Absolute
linear
value
CN2
OHE25K-108
MDS-A/B-V2-0
CN2
(Mitsutoyo)
CN3
Tv. MDS-A-SP
MDS-B-SP
Spindle System Section
1 Adjustment Procedure
1.I Trial operation
Do not make remarkable adjustments and changes

of the parametersas the operation could
become unstable.
Link the motor and machine, and check the control status while breaking in the machine.
(1) Do the command speed andactual speed match.
When they do not match, confirm the following
;
1) Are the spindle parameters(SPOOO to SP384) correctly set?
Especially check that the following parameters are correctly: set
1) SP017 (TSP)
2) SPO34 (SFNC2)
3) SPO40 (MTYP)
4) SP257 to SP384
2) Confirm that the following spindle

NC parameters are correctly set:
I)
Slimitl to 4
2) Smaxl to4
3) Smini
(2) Is the rotation smooth?

(3) Are there any abnormal noises?
(4) Are there any unusualodors?
(5)
Is the bearing temperature abnormal?
Next, run the motor

with an actual load, and confirm that there are no errors.
IV - I
.l_l
..
, .
1.2 Adjustment of orientation

1.2.1 Operation
1-
There are three types

of orientation stop that can be selected by setting parameter
.
1. PRE ........____............
(a)Spindleapproachesthestoppositionintherotationdirectionwhich
is
same as that of ongoing rotation.
2. Fonward run ..........._ (b) Spindle always approaches the stop position in the forward run direction.
3. Reverse run ............ ( c ) Spindle always approaches the stop position in the reverse run direction.
OHC
IV-2
Operation sequence
When orient command signal ORC turns O N , motor speed changes from steady run speed to
position loop changeoverspeedandatthesametime"stoppositioncommand"(multipoint
orientation) is read.
Whenmotorspeedreachesthepositionloopchangeoverspeed,controlmodechangesfrom
"speed control" mode to "position control" mode (position loop gain parameter (Note
1)).
(Position loop changeover speed is automatically set in accordance with position loop gain setting.)
When control mode changes to position control mode, the distance to the stop is
position
calculated
and spindlespeed is decelerated in accordance with the deceleration pattern set by parameter
to stop.
, orientedcompletesignal
When the spindleentersthe"in-position"rangesetbyparameter
ORCF turns ON.
The zeropoint can be shifted by setting parameter
.
When orient command signal (ORC) is turned OFF, motor speed returns to the previously set
reference speed.
1-1
=
I]
Motor speed
d
I
ORC
stop position
command
12b i
GRl. CR2, GR3
b-
QRCF
Note)
1-1
1-1
is used for magnesensor/motor built-ine n d e r type orientation, and

encoder type orientation.
IV-3
.~ .
for
1.2.3 Encoder orientation stop positions

The stop positions willbe asshown below depending on the direction that the encoder is installed.
Case 2
Case 1
Encoder
p
&
Motor
Installation
direction
Arrow A
Looking from arrowA
Looking from arrowA

Forward run
Reverse run
%j
ci$til
Normal
orientation
Forward
run
Reverse run
COOH
(270"
8obH
080' 1
800H
(180' 1
1.2.4 Parameter block diagram for orientation

Speed c o n t r o l blodc
block
Position
control
r
I
I
1-
I
From CNC
>
Power
amplifier
: Parameter name
&
'
Position feedback
Spindle
- .
Speed feedback
motor
GRB 1
CRA 1
Encoder
0-
Bit5 or Bit6
p[
x
-
IV-4
6
6
1.2.5 Preparation for adjustment

of motor built-in encoder orientation
[Related Parameters]
Parameter No.
SPOOl
SP004
SP005
SPO06
SP007
SP025
I
I
PGM
SP097
OINP
OSP
CSP
OPST
GRAl
GRA2
GRA3
GRA4
I
GRBl
I GRB2
GRB3
GRB4
SPEC0
SP098
VGOP
SP099
VGOl
SP100
VGoD
SP105
SP106
SP107
SP108
SP109
IQGO
IDGO
CSPZ
CSP3
CSP4
SP119
MPGH
SP120
MPGL
SP027
I
Abbrev.
SP029
SP030
SP031
SP121
SP122
MPCSH
MPCSL
Name
Ivalue
Default
Position loop gainfor magnesensor or motor
100
built-in encoder orientation
I Orientation
in-Dosition
width
I
16
0
Orientation changeover speed limit value
20
Deceleration rate during orientation
0
Orientation position shift amount
1
No. of gear teeth on spindle side1
1
SP026
No. of gear teeth on spindle side
2
1
3
1
SP028
4
I No.motor
side
ofon
teeth
aear
1
I
1
I No.motor
side
ofon
teeth
clear
2
I
1
1
No. of gear teeth on motor side
3
1
SP032
4
0000
Orientation specifications
Speed loop gain proportional item during
63
orientation
60
Speed loop gain integral item during orientation
Speed loop gain delayladvance item during
15
orientation
100
Current loop gain magnification during orientation
1
100
2
0
Orientation deceleration rate2
0
0
Orientation position loop gainH coil
0
compensation magnification
Orientation position loop gainL coil
0
Deceleration rate H coil magnificatiduring
orientation
Deceleration rate L coil magnification during
0
orientation
~~
[Preparation]
1) Confirm that the parameters are set to the values given above.
IV-5
~~~
1.2.6 Preparation for adjustment of encoder orientation

Parameter No.
SPO02
SPO04
SP005
SP006
SP007
SP025
SP026
SP027
SP028
SP029
SP030
SP031
SP032
SP096
SP097
Abbrev.
PGE
OSP
CSP
GRAl
G W
GRA3
GRA4
GRBI
P
GRB2
GRB3
GRB4
EGRA
SPEC0
1
SP098
VGoP
SPO99
VGOI
SPIOO
VGoD
SP105
SP106
SP107
SP108
SP109
IQGO
IDGO
SP119
MPGH
SP120
MPGL
SP121
MPCSH
SP122
MPCSL
CSP2
CSP3
CSP4
Default value
Name
100
Position loop gain during encoder orientation
16
Orientation in-position width OlNP
0
20
0
Orientation position shift amount OPST
Ito 32767
No. of gear teeth on spindle side 1
1 to 32767
1 to 32767
Ito 32767
1 to 32767
No. of gear teeth on motor side 1
Ito 32767
2
1 to 32767
1 to 32767
0
Encoder clear ratio
0000
63
orientation
60
Speed loop gain delay/advance item during
15
orientation
100
1
Current loop gain magnification during orientation 2 . 100
0
Orientation deceleration rate 2
0
0
Orientation positionloop gain H coil
0
Orientation position loop gain
L coil
0
Deceleration rateH coil magnification during
0
orientation
orientation
IV-6
[Preparation]
1)
The accurate gear ratio (or pulley ratio) from the motor shaft
required.
Confirm
that
the
correct
No. of gear
teeth
is
set
in
ISP032 (GRBI) 1.
.ISP025 (GRA1) I to I SP028 (GRA4) I = A
Note)
to the encoder rotation axis
1-
is
to
cxE
IsPo25 (GRA1) Ito I SPO32 (GRB4)
may be set by the user, so make sure that these

are set accurately to correspond to the machine.
IV-7
1.2.7 Preparationfor adjustment of magnesensor orientation

Pat.eter
Abbrev.
SPOOl
PGM
I
I
I
SP026
SP027
1
I
GRA2
GRA3
SP030
SP031
SP032
GRB2
GRB3
GRB4
Position loop gain for magnesensor or motor

I built-in
encoder orientation
SP098
1 1 1
SP099
SP100
SP106
IDGO
_ _ _ ~
Name
Orientation in-position width 16

Orientation position shift amount
1
1
orientation
Speed loop gain delay/advance item during
orientation
Current loop gain magnification during
orientation 1
Current loop gain magnification during
orientation 2
Orientation position loop gainH coil
L coil
Orientation position loop gain
Deceleration rateH coil magnification during
orientation
orientation
SP108
SP109
CSP3
SP119
MPGH
SP120
MPGL
SP121
MPCSH
SP122
MPCSL
SP123
MGDO
Magnesensor output peak value
SP124
MGDl
Magnesensor linear zone width
SP125
MGD2
Magnesensor changeover point
CSP4
IV-8
Default value
100
0
20
0
1 to 32767
1 to 32767
1 to 32767
1 to 32767
1 to 32767
1 to 32767
1 to 32767
1 to 32767
0000
63
60
15
100
100
0
0
0
0
0
Standard magnet= 542

Compact magnet = 500
Standard magnet= 768
Compact magnet= 440
Standard magnet = 384
Compact magnet = 220
[Preparation]
1)
The accurate gear ratio

(or pulley ratio)from the motor shaft to the magnesensor rotationisaxis
required.
Confirm
that
the
correct
No. of gear
teeth
is set
in
to
1-
. 1-
1to- 1
1-
Note)
may be set by theuser, so make sure that these

are set accurately to correspond to the machine.
Spindle
TT-
(A-F: No. of gear teeth)
IV-9
1.2.8 Adjustment of orientation

<Adjustment>
( { } for encoder orientation )
Orient positionshift adjustment

There is no volume or rotary switch for the osition shift.
.
position
parameter
with
the
shift
Set
1-
After setting
achieved.
, perform orientation, and adjustso that the target stop point

is
Orientation
Point at which speed
changes to oriented speed
Normal speed
Refer to the following table and set the corresponding orientation set.
~
~~
Adjustment
m
p
s
o
o
s
1
Phenomena
Overrun at stop
Long orientation time
Hunting at stop
alarm
Excessive
error
Note 1)
-/
: increase
setting
value.
: Do not change setting value.
s-Note 2)
1-1
Adjust
: Decreasesettingvalue.
The excessive error alarm will also occur when the detector direction
SP097
(SPECO) is incorrectly set.
1{ -
1-
} first and then adjust
1-1
To execute the shortest orientation time per gear setting, adjust
1, -
1in the same manner.

To set the shortest orientation time coil
perwhen using the
coil changeover motor, adjust
, 1,1ISP121 (MPSCH) Iand 1 SP122 (MPCSL) 1 in the Same manner.
and
If the
gear
ratio
is
excessive
error
alarm
occurs
and
cannot
be
remedied
with
the
above
adjustments,
Ifthe spindle rotates slowl in the forward/reverse run direction and does not stop during magnesensor
orientation, change the
detector installation direction bit.
ISP0970]
IV- 10
1.2.9 Adjustment of servo rigidity

Carry out adjustments with the following procedures to raise the servo rigidity.
to the extent that overrun does not occur during orientation.
Raise the position loop gain
For motor built-in encoder orientation and ma nesensor orientation:
Raise the
value.
1-
For encoder orientation : Raise the
SPOO2 (PGE)
1 value.
1-
Raise
the
and
values
with
the
same
proportion
the
degree
to
that vibration does not occur during orientation sto
is set to80, set
For example, if
1 - f
1I
to 80.
The value of SPlOO (VGOD) can be increased to raise the impact response during stopping.
However, if this value istoolarge,thetorque
for thepositiondeflectionwilldrop.Thus,the
movement couldbe adversely affected suchas the orientation stop position being inconsistent, etc.
PI control will be applied
if this value is set to0.
1.2.10 "Delay/advance control" and"PI control" application
1-
Normally, "delay/advance control" is selected. (
1 -
# 0)
In the case described below, select the"PI control" function. (

# 0)
Frictional torqueof spindle is large and particularly accurate stop is required.
When "PI control" is used, sew0 rigidity will be somewhat inferior than that in "delay/advance" control.
IV- 11
-._
.~
1.2.1 1 Troubleshooting during orient error

(1) Does not orient (Keeps rotating)
Cause
The parameter
setting valueis
inappropriate.
Remedy
Check items
The parameters with the orient
Set SP037 (SFNC5) correctly.
detector do not match.
1-
Remarks
Motor buitt-in encoder orient

............. 4
Encoder orient
............. 1
Magnesensor orient
............. 2
Specifications are Motor built-in encoder
not correct.
orientation is being carriedout
with a standard motor not
provided with theZ phase.
The connector pinNo. is
incorrect, or the connector
No.
where the wire is connected
is
incorrect.
The wireis broken. .
Change to the motor

with the
with Zmotor built-in encoder
phase.
For motor built-in

encoder orientation.
Change the wiring.
Change the wire.
(2) Stops after exceeding stopping point.

~~~~
Cause
Remarks
Check items
The parameter
setting valueis
inappropriate.
. 1-
The same applies

to the followin
Improves when the orientationReadjust

deceleration ratio parameter
ISPOO6 (CSP) I is halved.
ISP108 (CSP3) I
ISP109 (CSP4) I
Improves when the position

eters
SPOO1
(PGM)
and
,loop
gain
paray
Readjust SPOO1 (PGM) and
ISP002 (PGE) Iare halved.

The orient stop direction
is in
one direction (CCW orCW).
1-1
Set
1 to 0 h e ) .
Iv- 12
bit 0 and
The same applies

to the followin
The stop
isOFF.
- position
-
Cause
Machine factor
Check items
Remarks
Remedy
The stop positionis notOFF on There is backlash or slippage For encoder
the encoder axis.
between the spindle and
orientation
encoder.
The gear ratio between the
spindle and encoderis not 1 :1
or 1:2.
There is backlashor slippage
between the spindle and
motor.
spindle and motoris not 1: 1.
~
~~~~
~~~~~
For motor built-in

encoder
orientation.
~~
The position detection cableis Do not junction the cable.

junctioned with a terminal block
(connector), etc.
The position detector cable Correctly treat the shield.
shield treatmentis not correct.
The signal wireis peeled too
Keep the peeled section to
much at the position detector 3cm or less when possible.
cable connector section. Keep the peeled section as far
(The section not having a shieldaway from the drive line as
is long).
possible.
(4) The stop positiondoes not change even when the position shift parameter is changed.
Check items
The parameter
setting valueis
inappropriate
Remedy

If the gear ratio on the left is
spindle and encoderis 1:2
used between the spindle and
(encoder rotates once per two encoder, the position shift
spindle rotations), andthe
amount per spindle rotation is
position shift was changed to 2048 and not4096.
2048.
IV- 13
,
Remarks
1. Adiustment Procedure
(5) Vibrates when stopping.
CaUSe
The parameter
setting value is
nappropriate
Remarks
items
Check
Decrease the position loop

several Hz.
loop gain
Increase the current
Decrease thespeed loop gain

arameter for orientation
The vibration frequency

is
1OHz or higher.
Decrease the current

loop gain
(6) The oriented complete signalis not output.
Cause
items Check
Remedy
Refer to(1) Does not orient.
The machineload The in-positionis too small
is heavy.
(parameter
Change the orientation stop Review the values
set in the
control from delay/advance to
PI control.
I-].)
IV- 14
Remarks
1.3 Synchronous tap adjustment

1.3.1 Synchronous tap operation adjustment
<Preparation>
Before adjusting the synchronous tap, carry out operation with thespeedcommand
adjustment, and thenfollow the steps below.
or orient
<Parameter>
(1) Setting the spindle controller
#
:PO37
Description
Parameter
SFNCS spindle
unction
>ossibilities of orient type and synchronous taptype combinations and setting

lalU0S.
Semi-closed
Closed type
type
No orient
I
I
I
IOrient type
II
Encoder
orient
Magnesensor
orient
Motor built-in
encoder
I
0..... Possible,
lI 0x lI x0 l I o l o
I
l x l x l o l o
..... Not possible
IV- 15
Setting
value
4 1
(2) NC screen settings
Setting value
Description
:User parameter>
Synchronous tapis validated. When not valid, the conventional

tap Valid
zycle will run.
:Machine parameter>
3asic speci- )it3 of
ications
nparl
mrameters
a p t1
Servo
mrameter
[Z axis)
Spindle NC
Darameters
Spindle
parameters
'GNlSP
:svo49)
;gear
;tap 1
;tap 2
;tap 3
;tap 4
stap 1
;tap 2
;tap 3
;tap 4
PGT
SPECT
GRAlGRA4,
GRBl-
GRB4
EGEAR
0:Time
constant set
1:Slope set
Sets the position command time constant for the time constant
1to
set1500
synchronous tap.
(m-1
If the start up timefall
ortime to rotate to the considerable tap
max.Standard:
1000
s p e e d with theS command is t, set the following:
When tap precision is priority : tap-tl = t x 2 (ms)
When tap cycle timeis prionty: tap-tl = t X 1.2 (ms)
Sets the position loop gain during synchronous tap. Always
set.the 1 to 200
same value as for the spindle parameter PGT.
Standard: 10
Set whether the synchronous tap uses the time constant set
method orslope set method.
Sets the gearratio between the spindle and spindle encoder. 0

Always set to0 (1:Iwhen
)
not using the spindle encoder (semi- Standard: 0
closed type).
Sets the max. spindle
speed during theslope set tap cycle at gears0 to 99999
00, 01, 10, 11.
(wm)
Sets the time constant to
the max. tap speed during the slope set 0 to 5000
tap cycle at gears00, 01, 10, 11. The setting method is the same(msec)
as taptl above.
to 100
Sets the position loop gain during synchronous tap. Always set 1the
Standard: 10
same value for(Z axis) parameter PGNlSP.
bit 5 . ....... Sets the detector (spindle encoder) rotation direction
during synchronous tap. Set
0 for semi-closed.
bit 3.-...... Set to1for a strong excitation during synchronous tap.
The response to impact loads
wil increase. Normally0.
bit 0 ........ 0: Closed (when there is an encoder on the spindle)
1: Semi-closed (when there is no encoder on the
spindle)
bit 4 ..... ... Decides the motor command direction (spindle rotation
direction at G84) during synchronous tap.
bitE=O .... Performs zero point return at the beginning of the
synchronous tap mode.
bitE= 1.... Enters the position loop immediately after deceleration
and stopping without performing zero point return.
The gear ratio of each gear step mustset
becorrectly with the no.
of teeth.
Motor
Motor
shaft
side
speed x
No. of teeth (GRB1-GR64)
Spindleside No. of teeth (GRA1-GRA4)
Spindle
= speed
Sets the gear ratio between the spindle and spindle encoder. 0
Always set 0 (1:1) when not using the spindle encoder (semi- Standard: 0
closed type).
<Points of caution>
1) When the spindle is driven with belt
the or the timing belt in the semi-closed method (with no spindle
encoder) thebelt may slipor stretch and make precise synchronized tapping difficult.
belt, use the spindle encoder, and carry out synchronized tapping in the closed
When driving with the
method. In this case, use the encoder type orient for orientation.
2) When the spindle and encoder are connected with a speedofratio
2:l in the closed method (with the
spindleencoder),setthespindleparameterto
1.
Set the spindleNC parameter
E]
to 1.
<Confirmation and adjustment of the operations

Items to check during abnormal
operation
Normal operation
1-1
Spi-speed
Spindle
10 rotations in
Reverse
bit 4 when the
rotation direction goes in the reverse
tap direction.
When the rotation numbers differ,
recheck whether the parameter and
machine specifications match.
Others: Refer to troubleshooting for
synchronous tap error.
Refer to troubleshooting for

Carry out the cutting test with the floating tap chuck installed.
1) Is there any stretchingor shrinking of the tapper?
2) Is precisetap machining carried out?
Refer to troubleshooting for
Carry out the cutting test without the floating tap chuck
installed.
1) Is precise tap machining carried out?
1.3.2 Troubleshooting for synchronous tap error

Cause I mmedy
~
1 Excessivedifferencealarm(alarm
52)
1-1
I) The spindle parameter

bit 5 synchronous tap
detector direction is set
in reverse.
2) The spindle motor cannot follow the command
as the tap
time constantis too short.
Multiply the longer of the
S command's rising time or
falling time by 1.2 or more, and set.
1) The spindle motor cannot follow the command as the tap
time constant is too short.

Multiply the longer of the
S command's rising time or
falling time by 1.2 or more, and set.
3
1-
The spindle rotation movement amount

1) The spindle parameter
bit 0 close/semi-close
does not match the command value.
setting is wrong.
2) The spindle parameter gear ratio
to
1-1
to
gear ratio.
I 1)
Thetapbreaks.
The tap precisionis poor.
[=I
1,-
settings do not match the machine

-
1-
1) The (Z axis) parameter
and spindle parameter
1 x 1 values are not the same.

2) The tap time constant
is too short.
3)The programscrew pitch F and the actual tap pitch are
different.
4) The tap slips at the chuck. Change to a larger chuck with
a looser tightening
toque.
5 ) The prepared hole is shallow and the cut powder is not
removed well.
6) A tap with poor removal of the chip
is used.
(A spiral tap is desirous.)
7 ) The tap depth too
is deep for the tap diameter.
(Normally 2 to 3 times.)
8) A large noise interrupts the position feedback signal, and
the synchronized precisionis poor. In the closed method,
check the spindle encoder cable and in the semi-closed
method check the shield treatment ofspeed
the feedback
cable from the motor.
Check whether a normal shield wire is used iforit is
disconnected.
9) Redace with a new tap.
The spindle stopsor the precision

1) Set the spindle parameter
bit 3 to 1, and select
is poor during tappingas the load
the strong excitation.
is too heavy.
2) Increase speed loop gain during tapping.
3) Use tapping paste.
At low-speed rotations (under1000
1) The position loop gain
is slightly OFF.
rpm) there are no problems, and at (Example)
high speeds:
At close, the pulley ratio when
V belt connection is carried
1) The tap breaks.
out between the motor and spindle does not match the
2) The tap precision is poor.
theoretical gear ratio (a).
1-1
IV- 18
2. Troubleshooting
2. Troubleshooting
1. Always wait at least ten minutes after turning the power supply
OFF before starting maintenance
and inspection.
Failure to do so could lead to electric shocks.
2. Maintenance and inspection must be done by a qualified technician. Failure to observe this could
lead to electric shocks. Contact your nearest Service Center or Service Station for repairs and
part replacement.
2.1 Introduction
If any trouble occurs with the control unit, perform the preliminary checks described below and then
proceed to the troubleshooting described later.
The following preliminary checks are very important when
you consult with service engineer.
Preliminary check
NOTICE
1. Which alarm is displayed on the unit alarm display? Confirm the past alarms on the unit's 7segment displayor on the NC diagnosis screen. (Refer to the alarm and warning in
list2.4.)
2. Is the troubleor failure repeatable?
3. Are ambient and inner-panel temperatures normal?

4. When did the trouble occur (during acceleration,
or deceleration, or steady-speed operation)?
What was the

speed?
5. Is rotation direction correct?
6. Did instantaneous power failure occur?
7. Does the same trouble occur in a specific operation, or when a specific command is given?
8. How frequently does the trouble occur?
9. Does the trouble occur when load is applied,
or when load is removed?
10. Were emergency procedures performed?
11. How many years has the control system been used?
12. Is supply voltage normal?
Does it change from time to time?
2.2 First step of troubleshooting

Perform the following check:
(1) Power supply voltage: 200V(+10%-15%0) 50Hz, 200 230V (+10%-15%) 60Hz
In any case, it should not drop below
-1 5% of 200V.
(Ex.)
Check if the supply voltage drops at a specific time everyday.
Check if the supply voltage drops at start of a specific machine.
(2) Is the peripheral control unitor functions in good condition?
(Ex.)
Are the NC, sequence circuit, etc., proper?
Visually check the conditionof cables and other components.
(3) Is temperature inside and outside the control unit below
55"C?
(4) Visually check the control unit appearance.
(Ex.) Looseness in the connector, damageor entering of foreign matter, etc.
IV- 19
2. Troubleshooting
If the above status confirmation is carried out sufficiently, the faulty section should be apparent.
The most likely troubles or failures
of MDS-A-CV, SP can be largely divided into the following
two groups:
Trouble A
Control unit does not work satisfactorily when

is turned
it
on for the first time
(I).
Controlunitcomesintoastandstillabruptly
Control unit fails from time to time, or error occurs in orientation stop position, or "alarm"
lamp lights(111).
Trouble in power supply unit
Unit trouble
Trouble B
(11).
Trouble
with
detector
Trouble in spindle drive unit
Failure inspeed detect encoder

Trouble in 1024P/rev encoder
Trouble in9OOOOP/rev encoder
Trouble in magnesensor
Trouble in parameter, transfer data

from NC
Trouble with power supply
Trouble with motor
Other troubles (mismatching input sig,nal conditions, cable disconnection, etc.)
2. Troubleshooting
2.3 Second step of troubleshooting

Trouble I
Unit does not work
satisfactorily when
it is turned ON for
the first time
Check items
Remedy
As long as the control unit is handled

carefully, this type of trouble
is quite
unlikely to occur.
The most possible cause is,
(1) Mechanical shock or impact was
(A)
given to the unit during shipment,
installationor handling.
(2) External wiring or sequence is
(2)
incorrect, or disconnected.
Check aroundina wire.
(It is not required to consider power
phase sequence.)
(3)
Check for mistakes in the

parameter settings.
Motor speed cannot be increased.
Confirm that the 7-segment LED in

the unit is lit.
Check the external wiring and
sequence. (Note 1)
The inputloutput signals to the unit
can be checked on the NC spindle
monitor screen.
(3)
Checkthespindleparameters.
(4)
Check that the motor wires are

correctly connected toU W .
When using the built-in motor,
make sure that the waveform
output from the speed detector is
correct.
No-load operation is in good

condition.
(5)
Checktheloadcondition.
Only orientation stop function is not

in good condition (overrun, etc.)
(7) The C axis, synchronous tap, and
spindle synchronous are not
operating normally.
(6)
Adjusttheorientation.
(7)
Adjust and check the waveform

from each detector.
(8)
Referto 2.5.
(4)
(5)
(6)
Visually check if any part of the

equipment is damaged.
(8)
An alarm is displayed on the unit's

7-segment display.
Note 1) "Start signal CW, CCW' should be turned ON after "ready' signal and speed command been
have
input.
IV - 21
,
. ..,
2. Troubleshooting
Check items
Trouble I1
Control unit comes ( I ) Check the input power voltage.
into a standstill
AC200V + I 0% -1 5% 5OHZ
abruptly
AC200 to230V + I 0% -1 5% 60Hz
(2) Analarmisdisplayedontheunit's
7-segment.
Remedy
(1) Restore to normal if abnormal.
Secure a power capacity that can
maintain the voltages on the left
during operations (during
acceleration/deceleration, cutting).
I (2) Referto 2.5.
(3) Is the signal input fromNC correct'?
(3) Check on the NC spindle monitor
(4) Is the waveform output from each
(4) Check the waveform with a

synchroscope, and readjust or
replace.
screen.
detector normal?
Built-in speed detector
1024P/rev encoder
9OOOOP/rev encoder
Magnesensor
~~
Trouble I11
Check iteins
Remedy
Operation is not
In this case, the comprehensive analysis
correct sometimes. must be accomplished to determine the
The orientation
cause (load condition, operation mode,
stop position
etc.).
deviates.
Refer to the causes below.
An alarm displays, ( I ) The input power stopped
( I ) Perform a detailed investigation of
but after turning the instantaneously or dropped, and the
the inwt
. .Dower fluctuation, etc.
power OFF and
instantaneous stop alarm displayed.
I
ON or resetting,
(2) Check if malfunction occurred in
(2) Find the noise source, and install a
the operationis
control circuit, due to large noise.
surge killer, etc.
restored.
The unit is capable of withstanding
Review the unit's grounding,
noise (in power supply) of
detector shields and grounding, etc.
1600V/1ps.
(3) The orientation is incorrect.
(3) Readjust the parameters for
orientation. (Change the SPOOI,
The orientation stop position is
002, and 006 setting values.) When
deviated.
using the 1024P/rev encoder,
The orientation time is long.
inspect the backlash between the
spindle and encoder.
~~
~~
~~
~~
IV - 22
2. Troubleshooting
2.4 Alarm and warning table

Name
12
ME1
Memoryerror 1
M L;1ItZ-
13
SWE
'Oftware pr-ss
error
The
software
data
process
did
not
end
within
the
set
time.
PR
AD
17
L I
c).l
L3
32
34
error
3p11 IUIG UI I V G
Tp2
3B
PMOH Powermodule
overheat
40
KEl
41
KE2
CAXE
PR
PR
39
44
tSI I UI UclcIUlI CU II I L I IC
The current detectionAD converter did not function correctly

during initialization.
No
signal
(spindle
The
signal
was
not
input
from
the
spindle
encoder
(for
1 - 3 4
encoder)
I orientation, C axis), or was not at the normal level.
Excessive speed
The speed command
and
motor
speed
deflection
exceeded
UQL
for a specified time.
the specified value and the state continued
deflection
OS
Overspeed
The motorspeed exceeded 115% of the
set
max.
speed.
PR
A currentexceedingthesetvalueflowedintotheIPMusedby
Power module
PMOC
the spindle drive's main circuit.
overcurrent
DP
CRC error
1 A CRCerroroccurredinthecommunicationdatafromtheNC.
, Themovementcommand from the NCwasexcessivelylarge
AD
____
31
3UI I I UI M I V I GI
control card ROM.
Protocol error2
E\
PR
~~~
There was a protocol error

in the communication withthe NC.
(Information error)
Overheating of the IPM used by thespindledrive'smaincircuitwas
detected.
The
changeover
signal
procedure
was
mistaken
when
using
the TK unit.
TK
unit
The
communication
with
the
TK
unit
was
not
correct
when
communication error using the TK unit.
TK
unit
change
error
C axis changeover
DE>
When usingthecoilchangeovermotor,
C axis control was carried out
DR
I
I .
PR
DD
PR
PR
PR
PR
NR
Note) If the above protective functions activate, the alarmNo.w i l l be displayed on the 7-segment LED built into the
spindle drive, andthe following will occur.
Operation PR : The base currentof the spindle drive will be shut off, the external contactor will turn OFF,
and the spindle motorwill coast to a stop.
Operation NR : The spindle motorwill decelerate and stop with the regenerative motor, and then the base
current wil be shut off.
Operation AR : Only a warning wil display, and operation canbe continued.
IV - 23
2. Troubleshooting
2.5 Approach per phenomenon

.2.5.1 When alarm or warning is displayed on the 7-segment display
(1) Alarm No.
[Meaning]
: Memory
error
A check sum or RAM check error occurred in the spindle drive control unit ROM.
Investigation item
1
Investigate the wiring and

installation environment.
1) Is the unit correctly
grounded?
2) Is there any equipment

generating noise near the
unit?
Remedy
Occurs each time the power is Replace the spindle drive unit.
turned ON.
Perform investgation item
2,
and remedy.
1) The grounding is incomplete. Correctly ground.
2)The alarm occurs easily

when certain equipment
operates.
No special problem.
(2) Alarm No.

[Meaning]
Replace the spindle drive unit.
: Software process error

The spindle drive unit data process did not end within the set time.
Investigation item
1
Take noise prevention

measures for the left equipment.

grounded?
unit?
Investigation resub
Occurs each time the
power is
turned ON.
Remedy
2,
and remedy.
1) The groundingis incomplete.
Correctly ground.
2) The alarm occurs easily

operates.

measures for the
left equipment.
No special problem.
2. Troubleshooting
(3) Alarm No.
: AD converter
error
[Meaning]
The current detectionAD converter circuit did not function correctly during initialization.
Investigation item
Remedy
Occurs each time the power is

turned ON.

and remedy.

1) Is the unitcorrectly
grounded?
unit?
(4) Alarm No.

.

operates.
No special problem.
[Meaning]
Error in the 1024Plrev encoder for orientation 90,000

or
pulse encoder for C axisA, B, Z
phase signals.
~~~~~
Check the spindle parameter

(SP037: SFNCS) setting value.
Remedy
"1*'is set to Bit
0 even though
Correctly set.
encoder orientationis not used.
No special problem.

1211 : No signal detected
Investigation item
1
1) The grounding is incomplete.Correctly ground.

2,
and remedy.
Tug the connector to check if

the detector connector (spindleIs not disconnected (loose).
drive unit side and detector
Correctly connect.
Perform investigation item3,
and remedy.
Turn the power

OFF and check A connection defect or broken
the detector cable connection wire is found.
with a tester.

Correctly connect.'
When usingMBE-9OK for the C Connection

axis detector, peiform
investigationitem 4, and
remedy.
In other cases, replace the
spindle drive unitor detector.
When using theC axis built-in

detector MBE-SOK, check the
output waveform.
The waveformis not correct.
Readjust.
Replace the detector.
The waveform is correct.
IV - 25
2. Troubleshooting
( 5 ) Alarm No.
: Excessive speed deflection
The speed command and current motorspeed difference exceeded50wm or more for
12 seconds.
Investigation item
Investigation resub
Remedy
is not correct.
Correctly wire. The wiring
Check theU W wiring between
the spindle drive unit and motor. The wiring is correct.
Perform investigation item 2,
and remedy.
[Meaning]
'
Check the spindle parameters

(spo34, spo40, sp055vsp257 The correct values are set.
and following) setting values.
Correctly set. The values are not correct

and remedy.
Takes 12sec. or more. Increase

Measure the acceleration/
deceleration time to the max.
spindle speed. If the alarm
Takes 12 sec. or less.
occurs when changing from
forward run (reverse run) to
reverse run (forward run),
measure the time from
the
foward run (reverse run) max.
speed to the reverse run
(forward run)max. speed.
The load amount is 120% or
If the alarmoccurs during
cutting, check the load amount. higher.
The load amount is 119% or
lower.
the spindle parameter

(SP055) setting value.
4,
and remedy.

if
the
detector connector
(spindle drive unit side and
speed detector side)is
disconnected.
Correctly connect.
and remedy.
'
Is disconnected ( l o o s e ) .
Is not disconnected (loose).
Decrease the load.

5,
and remedy.
Turn the powerOFF and check A connection defect or broken Replace the detector cable.
Correctly connect.
wire is found.
the speed detector cable
7,
and remedy.
Adjust so that itis correct.
Check thespeed detector
waveform.
2. Troubleshooting
(6) Alarm No.
[Meaning]
1311 : Overspeed
The motor speed exceeded 115% of the value set in spindle parameter (SPO17:TSP).
Investigation item
1

(SPO17: TSP) setting value.
1) If the alarm occurs during
Remedy
Occurs only duringspeed loop
and remedy.
operation.
Occurs only during position loop.Perform investigation item3,
and remedy.
Occurs constantly.
and remedy.
Increase the setting value.
The setting value
is 2000' or
less.
The setting valueis 2001' or
and remedy.
more.
1) The SP193 bit5 (position

synchronous tap, check the
detector polarity) setting is
incorrect or the tap time
spindle parameter
constant setting is too low.
(SP193:SPECT) setting
value and the tap time
constant.
2) If the alarm occurs during
2) The SP177 bit5 (position
detector polarity) settingis
spindle synchronization,
check the spindle parameter incorrect or the spindle
synchronization time
(SP177: SPECS) setting
constant setting is too low.
value and the spindle
synchronization time
constant.
3)If the alarm occurs during 3)The SP129 bit5 (position
the C axis, check the spindle detector polarity) setting is
incorrect or each feed time
parameter (SP129: SPECC)
constant setting duringC
setting value, and C axis
axis is too low.
rapid traverse and cutting
feed time constants.
The set values are correct.
Correctly set.
Correctly set.
Correctly set.
4,
and remedy.

grounded?

operates.
unit?

measures for the
left equipment.
3)Are the speed and position 3)The shields are not correct. Correctly shield the cables.
detector cables correctly
shielded?
5,
No special problem.
and remedy.
Adjust so that it is correct.
Check the speed detector
waveform.
IV - 27
-....
2. Troubleshooting
(7) Alarm No.
[Meaning]
1921 : Power module overcurrent

A current exceeding the specified value flowed into the IPM used by the spindle drive
unit.
1
Investigation item
Check when the phenomenon
occurred.

(SPO34, SP040, SP055, SP257
Remedy
Occurs before readyON.
i
Occurs
ON. after
The values are not correct.
~~
The correct values are set.
The load amountis 120% or

If the alarm occurs during
cutting, check the load amount. higher.
The load amountis 119% or
lower.
Check the UVW wiring
between the spindle drive unit
and motor.
1) Are the terminal screws
loose?
2) Do the wires short-circuit
between phases?
3) Is there a ground fault
in one
of the phases?
Open both ends of the cable
when checking2)and 3).
Check the motor insulation.
Check between each motor
and ground with a megger
tester.
Check the power voltage.

and remedy.servo
Correctly set.
3,
and remedv.
Decrease the load.
~

4,
and remedy.
1) The screws are loose.
Correctly tighten.
2) There is a short-circuit.
Replace the cable.
3)There is a ground fault.
Replace the cable.
There is no special problem.

5,
and remedy.
Replace the motor.
The resistance value isMS

1Z or
less.
The resistance value 1
isMQ or
more.

6,
and remedy.
The powervobge drops below

170V during acceleration/
deceleration and cutting.
Review the power capacity.
7,
The power voltage is constantly Perform investigation item
and remedv. 171V or more.
~~
~~~~~~

grounded?
2)The alarm occurs easily

unit?
~~~~

operates.
No special problem.
~
~~

~
2. Troubleshooting
(8) Alarm No.
1341 : CRC error

A CRC error occurred in the communication data from the
NC.
[Meaning]
Investigation item
Remedy
Tug the connection connectorsIs disconnected (loose).

or terminating connectors
Force was applied.
between theNC and spindle
No special problem.
drive units, battery unit and
spindle drive unit, and spindle
drive unit and servo drive unit to
check if they are disconnected.
Also check if an excessive force
is being applied on the
connectors.
Correctly connect.
Disconnect each cable in item A connection defectwas found.

1, and check the connection
with a tester.
Replace the cable.
and
Investigate the wiring
grounded?
unit?
(9) Alarm No.

and remedy.
No connection defectwas found.

and remedy.
1) The grounding is incomplete.
Correctly ground.

operates.

No special problem.
Replace the spindle drive unit or

the MCP card on the NC side.
1351 : Data error
[Meaning]
The movement command data from theNC was excessively large during position
control.
Investigation item
Perform the same investigations items and remediesas for
alarm NO.
.
1341
(10) Alarm No. j361 : Transmission error

weaning]
The periodic data transmission fromthe NC was terminated.

~
~~~
Investigation item
Perform the Same investigations items and remedies
as for
alarm No.
.
1341
Remedy
esas
and
2. Troubleshooting
(11) warm NO.
: Parametererror
The spindle parameter sent from the

NC during initialization was illegal.
[Meaning]
~
~~~
Investigation item
setting Values. The No.
Of the
N~ special problem.
parameter with an abnormal
setting will display on the NC
spindle diagnosis screen.
Perform the same investigations items and remedies as for
alarm NO.
.
~~
(12) Alarm NO.
~~~~
Remedy
Correctly set.
and remedy.
: Protocolerror 1
[MeaninglTherewas a protocol errorin the communication with the

NC.(Frame error)
Investigation item
Perform the same investigations items and remedies
as for
alarm No.
.
Remedy
1341
1391 : Protocol error 2
(13)~lannNO.
[Meaning]
items
There was a protocol error in the communication with the NC. (Information error)
Investigation item
Perform the same investigations
Remedy
(14) Alarm No. (381 : Power module overheat
[Meaning]
1
Overheating of the IPM used

in the main circuit of the spindle drive was detected.
Investigation item
environment
1) Rotation of fan onrear of
Remedy
Take
Replace the The
fanmeasures
is not rotating correc
fan
to prevent cutting
Remarkable amounts of cutting Clean the finsoil or dust from
contacting the
fins.
radiatinG fins.
55C is exceeded.
ambient temperature
None of the above apply. Perform investigation item
2.
2 Investigate the installation
The grounding is incomplete.
Correctly ground.
Take noise measures for the
environment.
Alarms occur easily when
a
device onthe left.
Replace the unit.
devices in the periphery?
unit
IV-30
2. Troubleshooting
(15) AlarmNo. 140): TK unit change error

[MeaningJ
The changeover signal procedurewas mistaken when using the TK unit.

Investigation item
Remedy
Refer to the separate

1 amplifier
2 motor specifications (BNP-A-
2993-22).
(10)Alarm No.
[Meaning]
1411 : TK unit communication error

The communication between theTK unit and spindle drive unit was not correct when
using theTK unit.
Investigation item
Remedy
Refer to the separate 1 amplifier
2 motor specifications (BNP-A2993-22).
(17)Alann No.
waning]
1441 : C axis changeover alarm

When using the coil changeover motor,C axis control wascarried out with the H coil.
item
I
Investigation
results
I 1 I CheckInvemtigation
0 is displayed.
the sequence for C axis
changeover. Check the3H bit
~D display for the control input Iis displayed.
on the NC spindle monitor.
II
II
remedv.
0 is displayed.
Check the 3H bit D display for

control output when the
C axis
servo is ON.
Valid.
Check the parameters.
is to1.)
Is the coil changeover valid for (The SPO34 [mkch] bit set
sPecial motor specifications?
~~
Remedy
Issue the correct command.
(Check
sequence.)
the
and
.
Replace the amplifier.
~~~~~
IV - 31
Invalidate.
(Set the SP034 [mkch] bit to0.)
2. Troubleshooting
(18) Alarm No.
[Meaning]
: Motor overheat
The motor overheated and the thermal protector built-in the motor activated.
When this alarm occurs, it cannot

be released until the motor has stopped and the motor cooling fan has run
for 10 or more minutes.
Investigation
item
~
~~~~
Occurs immediatelyafter turning
power ON.
Occurs several minutes after
operation starts.
~~~
Occurs after operating for

a
while.
2
I Tugthe
Remedy
2,
and remedy.

5,
and remedy.
speed detectorcable
Is disconnected ( l o o s e ) .
connector on the spindle drive ' No special problem.
unit tosee if it is disconnected.
I correctlyconnect.
Check thespeed detector cable A connectiondefect is found.

connection.
I Correctlyconnect.
Check betweenOHSl and

OHS2 on the motor thermal
protector with tester.

3,
and remedy.

4,
and remedy.
The resistance valueis several

1O O n or higher.
Replace the motor.
The resistance valueis several

1OSZ or lower.
Check the spindle load amount.The unit is started and stopped Decrease the starting stopping
frequently, or the cutting load is frequency or lower the load.
large.
6,
No special problem.
and remedy.
Check the motor cooling fan The motor cooling fan wiring is Correctly wire.
wiring and rotation.
incorrect.
The wiring is correct but the fanReplace the motor.
does not rotate.
7,
No special problem.
and remedy.
7
motor cooling fan section.
No special problem.
Clean. The guard is clogged. Check the

2. Troubleshooting
(19) Alarm No.

[Meaning]
1501 : Overload
The current flowed to the spindle motor exceeded the overload detection level (spindle
parameter SPO64: OLL) and continued longer than the overload detection time (spindle
parameter SP063: OLT).
Investigation item
Check the spindle parameters The values are not correct.

(spo34,spo40,sp055, sp257 The correct values are set.
Remedy
Correctly set.

and remedy.
Check the spindle parameters Set the standard value.

is notThe
set. standard value
(sp063,spo64)setting values.
The standard value is set.
and remedv.
'
Check theUVW wiring between

the spindle drive unit and motor.
1) The screws are loose.
1) Are the terminal screws
loose?
2) There is a short circuit.
2) Do the wires short-circuit
between phases?
is a ground fault.
3)Is there a ground fault
in one
of the phases?
Open both ends of the cable There is no special problem.
when checking2)and 3). and remedy.
the
detector connector
Is not disconnected(loose).
disconnected.
Turn thep o w e r OFF and check A connection defect or broken
wire is found.
waveform.
Correctly tighten.
Replace the cable.
Replace the cable. 3) There
Correctly connect.
and remedy.
Replace the detectorcable.
Correctly connect.
and remedy.
~
~~~
Adjust so that it iscorrect.

(Refer to PageIV-38)

and remedy.
Check the motor load amount. The load amount exceeds the Decrease the load to within the
motor rating.
motor rating.
No special problem.
and remedy.
Check the motor rotation.
The motor is locked.
Review the machine side.
No special problem.
2. Troubleshooting
(20) Alarm No.

[Meaning]
: Excessive
error
The position tracking errorwas over the specified value (excessive error width setting
value) in the orientation or position loop operation.
Excessive error width setting value
During
orientation
(SP102:OODR)
: Standard
value
32767
(32767 pulses)
During C axis (SP154:CODRL, SP155:CODRH) : Standard value SP154:MCO,
SP155: 1 (120000 pulses)
Duringspindlesynchronization(SP186:SODR)
: Standardvalue32767
(32767 pulses)
During
synchronous
tap
(SP218:TODR)
: Standard
value
32767
(32767 pulses)
Investigation item
Remedy
Perform
investigation
item 2,
and remedy.
Occurs duringC axis.
and remedy.
Occuis during spindie
and
remedy.
synchronization.
Occurs during synchronous tap.Perform investigation item16,
and remedy.
1
Change thebit 5 setting value.
OK if the bit 5 setting value is
If the alarm occurs during
encoder orientation, check the changed.
spindle parameter (SP097:
Return thebit 5 setting value to
NG even if the bit5 setting
SPECO) bit 5 setting value.
the original value, perform
value is changed.
investigation item3,and
remedy.
Occurs during orientation.
OK if PGM and PGE are

doubled orif CSP is decreased
to half.
NG even with the above
settings.
if
the detector connector (spindle 1s not disconneed (loose).
drive unit side and
positionkpeed detector sides)
is disconnected.
Change the setting values.
Turn the powerOFF and check A connection defect or broken

wire is found.
the positionlspeed detector
cable connections with a tester. Connection, is

Correctly connect.

(SPOOI:PGM, SP002:PGE,
POO6: CSP) setting values.
'

waveform.
The waveform is not correct.
The waveformis correct.
Iv-34

and remedy.
Correctly connect.
and remedy.
Perform investigationitem 6,
and remedy.
(Refer to Page IV-35)
position detector.
2. Troubleshooting
Investigation item

(SP129: SPECC)bit 5 setting.
Investigation
results
changed.
Remedy
Change the bit5 setting value.
Return the bit5 setting value to
investigation item8 , and
remedy.
NG evenif the bit5 setting

value is changed.
Change the setting value.
OK if settina value is lowered.

Check the axis specifications
parameter rapid traverse and NG evenif the setting value is
cutting feed rate setting values. lowered.
Return the setting value to the

original value, perform
investigation item9, and
remedy.

Check the axis specifications
parameter time constant setting
value.
NG evenif the setting value is Return the setting value to the
increased.
investigation item 10, and
remedy.
I
~
Check
parameter
spindle
the
value.
setting
the
Change
(sPoo3:FGco, SP130
SP133: PGCI PGC4, SP165: NG evenif the setting value is Return the setting value to the
pG2c, SP166:PG3C) setting
increased.
values.
investigation item1 1 , and
I
is not set.
Check the other spindle
parameters
sp166s No special problem.
SP257 and following)

(SP177: SPECS) bit 5 setting.

changed.
NG evenif the bit 5 setting
value is changed.
Check the spindle parameter's OK if the setting valueis

increased.
spindle synchronous time
constant.
NG evenif the setting value is
increased.
OK if the setting value is

increased.
(SP010: PGS, SP189: PG2S,
sp190:PG3S) setting values- NG even if the setting value
is
increased.
Iv-35
remedy.
Correctly set. The correct value
readjust or replace the position
detector.
Change the bit5 setting value.
Return the bit5 setting value to
remedy.
remedy.
remedv.
2. Troubleshooting
Remedy
The correct value is not set. Correctly set.
Check the other spindle 15
parameter (SP1T7 to sP190,
No special problem.
SP257 and following) setting
values.
detector.
Check the spindle parameter OK if the bit 5 setting value is Change thebit 5 setting value.
(SP193: SPECT) bit 5 setting.
changed.
Return thebit 5 setting value to
NG evenif the bit 5 setting
value is changed.
remedy.
Check the spindle parameter's OK if the setting value is
increased. spindle synchronous time
constant.
NG evenif the setting value
is
increased.
remedy.
is
Check the spindle parameter OK if the setting value
increased.
(SPOO9: PGT, SP221: PG2T,
sp222: PG3T) setting values. ' NG even if the setting value is Return the setting value to the
increased.
remedy.
Correctly set.
1 Check theotherspindle
I Thecorrectvalueisnotset.
values.
detector.
I
Investigation Rem
II
16
17
18
19
The tracking error amount (droop amount) be

can
calculated with the following equation.
If this value exceeds each excessive error width setting, this alarm
wil occur.
The No. of pulses per rotation isas follows:

During C axis
:360000
Other than the above : 4096
(*2) The spindlespeed during C axis is calculatedwith the following equation.
(4)
Spindle speed (rpm) =
C axis feed rate ("/min)

360"
2. Troubleshooting
(21)Alann No.
ml
[Meaning]
The pulse miss value was higher than the parameter set value
(SPI 14: OPER) when
orientation positioning was completed.
lnvestiaation item
Is the speed detector cable
shield correctly treated?
Investigation
results
The shield is correct.
The shieldis correct.
Is the encoder cable

junctioned?
It is junctioned.
It is not junctioned.
Stretch and contract the

encoder or speed detector
. cable, and usea tester to
- check for wire breakage.
4 Are theA, B and Z phase
waveforms of thespeed
detector correctly adjusted?
The wire broken.

The wire is not broken.
(22) Alann No.

[Meaning]
to
[Meaning]
Correctly adjust. Refer to the

adjustment procedures (BNF14052-01).
The waveformis correct. Perform investigation item
4,
and remedy.
: Power supply error
An error occurred in the power supply.
The current flowed to the spindle motor exceeded the overload detection level (spindle
parameter SPO64: OLL) and the time exceeded
80% of the overload detection time
(spindle parameterSP063: OLT).
I 11501-
Check whether the emergency

stop switchis ON.
The emergency stop command was input from theNC or an alarm occurred in another
servo axis or in the spindle.
Switch is ON.
Switch is OFF.
Remedy
: NC emergencystop
Investigation item
weaning]
Remedy
: Overload
warning
Investigation item
Perform the same investigation
and remedies as foralarm No.
(24) Warning No.
Remedy
Correctly treat the shield.
and remedy.
Use one encoder cable.
and remedy.
Replace the cable.
and remedy.
The waveformis deviated.
Investigation item
Refer to the power supply
troubleshooting section.
(23) Warning No.
Performthesameinvestigation
and remedies as for alarm No.
IV - 37
Remedy
Turn OFF the emergency stop
switch.
and remedv.
2. Troubleshootins
2.5.2 When alarm or warning is not displayed on 7-segment unit

(1) Motor does not rotate even when an alarm
is not displayed.
Investigation Rem
The wiring is incorrect. Loose

Check the wiring around the
power supply unit and spindle screws or broken wires are
found.
drive unit.
Also check for looseness in theNo special problem.
terminal screws and for broken
wires, etc.
The voltage exceeds the
Check the input vottage.
specified value.
The voltageis within the
specified value.
Confirm all spindle parameters. The correct valueis not set.
The correct value is set.

4
Remedy
Correctly wire.
Tighten the screws.
Replace the wires.
and remedy.
Restore the power to the
specified value.
and remedy.
Correctly set.
4,
and remedy.
Confirm the input signals.

(Confirm on the spindle
diagnosis screen.)
Are the ready, forwardrun,
reverse run signals input?
The signal is not input or the Correct the input signals.

sequence is incorrect.
The orientation commandis
input.
The forward and reverse run

signals mustbe input at least
one second after ready
ON.
The forward run and reverse
run signals may
be turned ON
simultaneousty.
Confirm thespeed command.
diagnosis screen.)
No special problem.

5,
and remedy.
Correctly input the

speed
command.
The speed command is correctly Replace the spindle drive unit.
input.
The speed command is not

correctly input.
(2) An alarm is not displayed but the motor only rotates slowly. The sound from the motor
is loud.
Check theUVW wiring between The wiring is not correct.
the spindle drive unit and motor.
' The wiring is correct.
Confirm the input voltage.
to the
One of the three phases is not Restore the power
specified value.
the specified value.
3,
No special problem.
and remedy.
speed command.
diagnosis screen.)
Correctly
speed
The speed command is not Confirm
the input the
correctly input.
command.
Investigationitem
Remedy
Correctly wire.
Perform' investigation item2,
and remedy.
4,
The speed command is correctly Perform investigation item
and remedy.
input.
2. Troubles hooting
~~
~~
~~
Investigation item
~~~~

*"peed
detector connector
disconnected.
I Is disconnected (loose).
connect.
Correctlv
and remedy.
Turn the powerOFF and check

waveform.
Remedy

connect.
Correctlv
I The waveform is correct.

and remedy.
Replacethespindledriveunit.
I
I
(3) The commandedspeed and actual speed do not match.

Investigation item
1
Confirm thespeed command.

diagnosis screen.)
Check for slips between the
motor and spindle.
(If the belt or
dutch are connected.)

correctly input.
The speed command is correctly
input.
Slipping is found.
No special problem.
is not set.
(spas, spwo, spo17, sp257 The correct value is set.
and following).
Remedy
Correctly input the speed
command.
2,
and remedy.
Repair the machine side.
and remedy.
Correctly set. The correct value
(4) The start up time is long or has become longer.
Investigation item
Check if the frictiontoque has

increased.
Rotate the motor bearings

by
hand tosee that theyare
normal.
The torque has increased.
Remedy
Repairthemachineside.
No special problem.

2,
and remedy.
The bearings do not rotate

smoothly.
The bearings rotate smoothly.
Replace the spindle motor.
Check if the torque limit signal is The signal is input.

being input. (Check on the
The signal is not input.
spindle diagnosis screen.)
IV - 39
."

3,
and remedy.
Do not input the signal.
2. Troubleshooting
( 5 ) The motor stops during cutting.
Investigation item
Remedy
Check the load amount during The load meter indicates a value
Decrease the load.
cutting.
higher than 120% during cutting.
2,
and remedy.
No special problem.
2
Perform the Same investigation

and remedies as for item
(4).
(6) The vibration and noise (gear noise)is large.
Investigation item
Check the machines
movement balance.
(Free run from the max.
speed.)
The same sound is heard duringRepair the machine side.

free run.
No special problem.
~
~~
~~
~~~~~

and remedy.
~ ~ _ _ _ _
Check for a resonance point on

The vibration and sound
the machine.
speed
increases at a certain
(Free run from the max.
during free run.
speed.)
No special problem.
Check the machine backlash.
Remedy
Backlash is large.
No special problem.

3,
and remedy.
4,
and remedy.
Confirm the spindle parameter The phenomenon decreases

(SP022: VGNPl, SP023:
when the setting value
is
VGNll, SPO56: PYVR) settings. lowered to half.
No change evenwith the above
settings.
Change the setting. Note that

the impact response
will
decrease.
remedy.
Tug the connector to checkif

the speed detector connector
speed detector side) is
disconnected.
Correctly connect.

6,
and remedy.
Turn the powerOFF and check A connection defect or broken Replace the 'detector cable.
wire is found.
Correctly connect.
7,
. .
and remedy.
waveform.
2. Troubleshooting
(7) The spindle coasts during deceleration.
Investigation item
1
Check for slips between the

motor and spindle. (If the
belt or
clutch are connected.)
Slipping is found.
Remedy
No special problem.
(8) The rotation is not stable.
Investigation item
Remedy
Confirm the spindle parameter The stabilizes when the setting Change the setting. Note that
(SPO22: VGNP1, SP023:
values are doubled. the gear noise may increase.
VGNI1) settings.
No change even with the above Return the setting value to the
original value, perform settings.
remedy.

if
Is not disconnected(loose).
disconnected.
Turn thepower OFF and check A connection defect
or broken
wire is found.
Check the speeddetector
waveform.

Is grounding properly
performed?
Correctly connect.
and remedy.
Correctly connect.
and remedy.

and remedy.
Correctly ground.
No special problem.
IV - 41
..
2. Troubleshooting
(9) The motor speed does not rise above a certain speed.
Remedy
Correctly input the
speed
Check the speed command.
command.
correctly input.
[Confirm on the spindle
diagnosis screen.)
2,
The speed command is correctly Perform investigation item
Confirm whether the override
and
remedy.
input.
input on the machine operation
Dane1 is beina inwt.
The load has increased.
Check whether the load has
increased suddenly.
3,
No special problem.
and remedy.
Replace the spindle motor.
Check that the motor bearings The bearings do not rotate
smoothly.
can be rotated normally by
hand.
4,
The bearings rotate smoothly. Perform investigation item
and remedy.
Correctly connect.
if
5,
and remedy.
disconnected.
Turn the power
OFF and check A connection defect or broken Replace the detector cableCorrectly connect.
wire is found.
6,
(Especially checkthe shield
and remedy.
wirina.)
Check the speed detector
waveform.
Investigation item
~~
2. Troubleshooting
2.6 Periodic Inspection
1. Always wait at least ten minutes after turning the power supply
OFF before starting maintenance
and inspection.
Failure to doso could lead to electric shocks.
2. Maintenance and inspectron must
be done by a qualified technician. Failure to observe this could
lead to electric shocks. Contact your nearest Service Center or Service Station for repairs and
part
replacement.
The periodic inspection

is particularly important to ensure high-performance operation of equipment, and
trouble-free long useof equipment.
To prevent major accidents, make sure the power is interrupted completely before starting the
inspection. Make sure that the CHARGE lamp on the power supplyisunit
OFF.
2.6.1 Inspection of control unit
NOTICE
Never perform a megger test (insulation resistance measurement) on the spindle amplifier control
circuit.
Check item
Frequency
1. Cooling fan
Monthly
2.Dirt and terminal
Appropriate
interval
screw looseness
3.Wiring
Appropriate
interval
Check
Replace the fan.

(1) Rotate the fan shaft manually to check.
(2)Turn ON the fan to check that the fan runs
powerfully.
(3)Check if abnormal sound occurs in
bearing.
Periodically clean the areas around the
amplifier, especially the cooling fan, and tighten
the inputloutput terminals and connections.
Check that the wires are not contacting the
conductive parts and that they are not caught.
IV - 43
2. Troubleshooting
2.6.2 Inspection of motor

Check
Frequency
1. Noise and
Monthly
OCheck if abnormal sound or intense

vibration occurs.
If abnormal sound or intense vibration occurs,
perform the following check:
(1) Check foundation and installation.
(2)Check shaft alignment.
(3)Check if vibrationis transmitted through
shaft coupling.
(4) Check if bearingis damaged or abnormal
noise occurs.
(5)Check if noise or vibration is caused by
reduction gear orbelt.
(6)Check control unit for condition.
(7)Check cooling fan for condition.
(8)Check belt tension.
Monthly
0 Check bearing temperature.
vibration
2.Temperature
Remedy
Clean
rise
(Normal amb. temp.+ 10 to 40C)

motor frame temperature.
If temperature is high excessively, perform the
following check:
(1) Check cooling fan operation.
(2) Check cooling air passage (between frame
and cover).
(3)
Check load condition.
.--------------------------Refer to2.5.
(4) Check control unit.
0Check if insulation resistanceis excessively
low.
Disconnect the wiring with the spindle drive
unit, and measure the resistance between the
entire circuit and ground. (There
is no problem
if the valueis 1MSL or more with a 500V megger
tester.) If the insulation resistance
is less than
1Ma, clean the inside
of the motor and dry
it
out. To dry, disassemble the motor and heat
it
in a dryer at
a temperature less than90C.
0Check
3. Insulation
resistance
Every 6
months
Weekly,
monthly
0Check
cooling fan for operation, abnormal

noise and vibration.
3. Disassembly and Assembly of Motor

3.1 Disassembly and assembly of SJ type AC spindle motor
Cablesand PCB
Terminal box cover
(1)
_ _ Remove the coverof terminal
box on the fan case.
(2) Disconnect the cables coming

from thepower panel.
a) 3 motor main leads
(U, V and W).
b) 2 cooling fanleads
(BU and BV).
c) 2 thermal protector leads
(OHS1 and OHS2).
d) Mate plug of PCB 's
external connector.
. _,(.
Fan case'
PCB fixing pan head screw
(3) Remove the external

connector fromthe mnnector
PCB
bracket.
Disengage the internal
connector.
(4) Remove thePCB fixing pan
head screws to remove the
PCB.
( 5 ) To assemble, perform the
steps inreverse [ (4) to (1) 1.
External connectorbracket
~~~~~l
connector
Internal connector
\'
'\
Leadprotectionpacking
L.
IV - 45
.,
. -.
3. Disassembly and Assembly of

Motor
Cooling fan
For typessmaller than frame
No.132
(1) Remove the hexagon socket
head bolts fixing the finger
guard.
(2) Remove the pan-head screws

at the centerof the cooling fan
to remove the fan.
(3) Cut the four fan leads.

Remove the pan-head screws
and drawout the fan motor
from the fancase.
'
To assemble, perform the

steps in reverse[ (3) to (1) 1.
Fan motor
--
Fan
For types larger than frameNo. 160

(1) Remove 3 fan case mounting
hexagon socket headbolts.
Pull back the fancase to
remove the fancase together
with fan.

head bolts fixing the finger
guard.
IV - 47
.."_. ."
(3) Cut the three cooling fan leads.

Remove the pan-head screws
fixing the cooling fan and draw
out the fanfrom the fancase.
(4) To assemble again, perform
the steps in reverse

[ (3) to
(1) I.
Cooling fan.
~
- , . - ......
Finger guard
--\\
Sensor and sensor gear

(I)
Disengage the sensor
connector (internal) from the

PCB in the terminal
box.
(2) Remove the three fan
mounting hexagon socket
head bolts. Pull back the fan
case to remove the fan case
together with fan.
IV - 48
.--
-.
..
Remove thetwo pan-head

screws fixing the sensor
bracket to remove the sensor
bracket together with sensor.
(Take care to prevent hitting
the sensor against the sensor
gear.)
To adjust sensor position,
loosen the sensor fixing screw
with the sensor bracket held
in
position and insert
a thickness
gauge into the gap between the
Sensor and the Sensor gear.
Adjust the gap
to 0.15i0.01.
After making sure that the
Sensor marking lines are
aligned with each other, tighten
the Sensor fixing screwto
secure the Sensor in position.
(Refer tothe figure on the
right)
Sensor bracket
Sensor
\.
Sensor bracket mounting screw
\\
"\\
\\
Apply lock paint to the sensor

fixing screw and the sensor
bracket mounting screws.
When the Sensor is put into the
fan c a s e , arrange the sensor
leads properly to prevent
Sensor lead from being
wedged.
Sensor gear
I
(7) To remove the Sensor gear,

screw eye bolts (M8) into the
screw holes and usinga screw
bolt
removing tool, rotate the
with a wrench, etc. Then,
remove.
(8) To install the Sensor gear again,
it must be shrinkage-fit at a
temperature within 100C to
150C.
Note that an excessively high
temperature may cause
distortion to the gear.
Match marking lines
IV - 49
Bearinns
Apply sealing
compound.
Bracket fixing bolt
Remove the bearing case

cover fixing screws and the
bracket fixing hexagon socket
head bolts and remove the
bracket on the opposite drive
side.
When the bracket on the
opposite drive side is installed
again, apply sealing compound
to the fittingsurface.
Bearing case cover fixingscrew
(3) To remove the bearing on the
I^\
opposite drive side, remove the

shaft stop ring and apply a
bearing remover.
The bearing can be removed
together with the shaftcase
cover.
1
I
i
/
Shaft stop ring

drive side, apply a bearing
remover to the innerring of
bearing andturn the handle of
bearing remover.
IV - 50
---
( 5 ) To install bearing onto shaft, all fitting surfaces should

be thoroughly cleaned and smoothed.
Press here.
(6) Apply grease to bearing bore surface and shaft.

Put a pipe
on the bearing inner ring and carefully depress
the bearingwith a press machine.
pipe
Bearing
Installation with press machine

(7) If press machine is not available, lightly hammer the to
pipe
drive.
Use care not to hammer the outer ring
of bearing.
Pipe
Bearing
Installation withhammer
IV - 51
.*-
<Confirmation of motor built-in encoder (speed detector) waveform>

The waveform mustbe confirmed and adjusted before running the motor after disassembly and
reassembly.
Z phase. Refer to the separate ADJUSTMENT
Theexplanationhere is forthemotorwithoutthe
PROCEDURES (BFN-14052-01) when using the
Z phase.
1.
PCB volumelayoutdrawing
Check
PA
PB
AGA
terminals
: A phasesignal
: B phasesignal
: Ground
Volume
VRI : A phase 0 position adjustment
vR2 : A phase gain adjustment
VR3 : B phase 0 position adjustment
VR4 : B phase gain adjustment
2.
Confirmation
method
(1) Set the spindle parameter SP038 (SFNC6) Fbitto "1" and turn the NC power
OFF and ON.
(Enter the open loop.)
( 2 ) Input the forward run command, and gradually raise the motor
speed to 1800rpm.
(3) Measure theA and B phase waveforms with a synchroscope.
(4) Confirm that the waveformis as shown below.If not as shown below, adjust with
VRI to VR4.
( 5 ) If the waveform cannot be adjusted with VRI to 4, readjust the gap between the sensor and
gear teeth.
1) If voltage level does not decrease below
i1.6V: Increase the gap
2 ) If voltage level does not increase above
&
.4V:
I Decrease the gap
(6) Next, reverse run the motor and measure the waveform at 1800rpm.
( 7 ) Set the SP038 (SFNCG) bittoF"0"after completing the confirmation and adjustments, and turn
the NC power OFF andON.
A phase
B phase
Voltage M
B phase A phase
-1.63
-1.55
A phase/B phase output signal waveform

during forward run
A phase/B phase output signal waveform

during reverse run
3. Disassemblv and Assemblyof Motor
3.2 Disassembly and assembly of SJ-N type AC spindle motor

Cables and PCB
terminal
the
Remove
(1)
box cover
on the top
of the fancase.
(2) Disconnect the cables and
leads coming from the power
control box.
3 motor main leads
(U, V and W).
2 cooling fan leads
(BU and BV).
2 thermal protector leads
(OHSl and OHS2).
Mating plug to external
connector of PCB.
Terminal box cover
Fan case
(3) Remove the external
PCB
PCB fixing pan head screw
connector from the connector

bracket. Disengage the
internal connectorfrom the
socket.
(4) Remove the PCB mounting
pan- headscrews to remove
the PCB.
( 5 ) To assemble, perform the
steps in reverse [ (1) to (4) 1.
For details, see (6).
! Lead protection,
- -. packing
IV - 53
(6) Mounting of the PCB
Method: Fix with two bolts together

with the case. Connect
the sensor connector.
Connect the output cable
Do not
Caution:totheamplifier.
allow the motor power
cable to contact the
bottom of the amplifier. J
The motor cableis under the amplifier.
The motor cable protrudes from the amplifier.
3. Disassemblv and Assemblyof Motor
For frameNo. 90
(1) Remove two hexagonsocket
head bolts used to secure the
cooling fan.
The cooling fan canbe
removed fromthe fan case
assembledwith finger guard.
-/--
(2) To reassemble, perform step

(1) in the reverse order.
IV - 55
,
For frame No.112

head bolts used to secure the
finger guard.
(2) Remove the pan-head screws

at the center of the cooling fan
to removethe fan.
Cut the four fan leads of the

cooling fan which are
connected inside the terminal
box.
Remove the pan-headscrews
used to mount the fan motor
assembly and draw out
the fan
motor from the fan case.
(4) To reassemble, perform steps

(1) to (3) in the reverse order.
Fan -motor
..
Sensor and detection drum

(1) Disengage the Sensor
connector (internal) fromthe
PCB in the terminal box.
(2) Remove the threefan case
fixing hexagon socket head
screws.
Pull back the fan case to

case together
remove the fan
with the coding fan.
(3) Remove two pan-head screws

used to fix the sensor bracket
and the Sensor bracketcan be
removed togetherwith sensor.
(Take care to prevent hitting
Fixing screw for installation
the sensor against the

detection drum),
IV - 57
(4) Mounting the sensor
Conditions:
Position with the SensorV-type base
side and the motor base positioning
ring protrusion.
Preparation:
Clean (air blow) the sensor block
mounting face (motor base) and the
sensor V-type base side.
Method:
Lightly fix the Sensor block
with bolts
(so that the block can be moved.)
Tighten the boltso that the Sensor
block is pressed against the mounting
face andso that theV-type base side
contacts the motor base positioning
ring as shown in the figure.
Caution:
Take careso that the sensor base
does not slip from the tightening
of
the bolts.
Do not apply strength to the flexible
plate.
( 5 ) Apply lock paint to the sensor

fixing screw and the sensor
bracket fixing screws.
(6) When the sensoris put into the
fan c a s e , arrange the Sensor
leads properly inside the
terminal box to prevent sensor
lead from being wedged.
(7) Removal of the drum
removal jig.
Caution: The removed drum
To remove the detection drum,
an eye bolt is screwed into the
screw hole (M8 screw), and the
removing bott is removed using
a remover while tuming with a
spanner, etc.
(8) Installation of the drum
Condition:
Heat
fitting
(heated
temperature:
below 150C)
Method:
Confirmthatthedrumisatthespecifiedtemperature.
Hold the drumwith leather gloved hands and quickly insert
it.
Caution:There
mustnot be a magneticfield of over 50G insidetheheatingdevice.
Cotton gloveswill slip.
Confirmation: Is thedrumcompletelyinserted?
IV - 59
_.& .
Bearings
Apply
sealing
compound.
Bracket
fixing
(1) Remove the bearing case

cover fixing screws and the
bracket fixing hexagon socket
head bolts and remove the
bracket on the opposite drive
side.
(2) When the bracket on the
opposite drive side is installed
again, apply a sealing
compound to the fitting
surfaces.
opposite drive side, remove the

C type shaftstopringandapply
a bearing remover.
Turn the removingbolt with
spanner and the bearing can
be removed together
with the
shaft case cover.
Bearingcasecoverfixingscrew
drive side, apply a bearing

remover to the inner ring
of
bearing and turn the handle
of
bearing remover.
Shaft stop ring
IV - 60
bolt
( 5 ) To install the bearing onto the shaft, all fitting surfaces
should be thoroughly cleaned and smoothed.

(6) Apply grease to bearing bore surface and shaft.
Put a pipe on the bearing inner ring and carefully
depress the bearing with a press machine.
&
Press here.
pipe
Bearing
Installation with press machine

( 7 ) If press machineis not available, lightly hammer the pipe to drive the bearing in.
the bearing.
Use care not to hammer the outer of
ring
Bearing
Pipe
Installation with hammer
IV - 61
___5_
...

4.1 Magnesensor I-point orientation
4.1.1 Magnet and sensor
The sensor generatestwo types of voltage signals as shown in Fig.
6.1.
Direction of Rotating
disk rotation
plate
output
Amplifier
1-1
+8-
+sv ;
Between CN6 (7)to (17 )
Fig. 6.1 Sensor Output Voltage

MS signal : Signal voltage output isOV when the centerof magnet comes to the sensor head, and
maximum at both ends
of the magnet.
Spindle is stopped with this signalOV.
at
(Note that the target voltage
will fluctuate a max.of & 2.5V depending on the position shift
setting.)
LS signal : Signal voltage is constant within the magnet zone (width).
This signal is used to verify that spindle remains stopped within the magnet zone.
IV - 62
4.1.2 Orientation of magnet and sensor head

The magnet and sensor head should be installed in the specified orientation.
Standard type
High speed standard type
............. The center reference hole of magnet and the reference notch
of sensor head should come
to
the same side.
Refer to
and [UNACCEPTABLE EXAMPLE11.
High speed miniature type
.._..........The reference notch of sensor head should be positioned in reference with polarity
S)(N.
of
magnet.
Refer to
High speed ring type
............. The reference notch of sensor head should be positioned in reference with(N.
polarity
S)of
magnet.
Refer to
m,
m,
1-
1-1
,14-1
1-
-I,
1-
Magnet is installed on the circumferential surface of rotating disk.

(Circumferential mounting)
The center reference hole of magnet and the reference notch of sensor head should come
to the opposite drive side of the spindle, as shown below.
n
Reference hde
d'-l
'
1
1
1
Reference
notch
View from "A'
Magnet is installed on circumferential surface of rotating

disk.
IV - 63
y u c -
Magnet is installed on the front

or back flat surface of rotating disk.
(Flat mounting)
(1)
Whenthemagnetisinstalledonthe
(2) Whenthemagnetisinstalledonthedrive
opposite drive side of spindle, the reference side of spindle, the reference hole
of magnet
holeofmagnetandreferencenotchofandreferencenotch
of sensorheadshould
sensorheadshouldfaceinward,asshownfaceoutward,asshownbelow.
below.
Reference
notch
Reference
hole
Yp-c
Reference
View from "B"
Reference
hole
notch
Reference
Reference
hole
notch
View from "C"
MagnetisinstalledontheoppositedriveMagnetisinstalledonthedriveside.
side.
13 - 1
1-1
In regard to
, the magnet and sensor head canbe changed to the following
position as long as the reference hole and reference notch are aligned. With this, normal
orientation canbe carried out.
(However, the parameter SP097SPEC0 magnesensor detection polaritybit mustbe
changed in this case.)
Reference hole
Reference natch
[UNACCEPTABLE EXAMPLE1
If the magnet reference hole and sensor head reference notch are not aligned; intense vibratio
will occur when the sensor head is at end of magnet (orientation is impossible.)
Reference hole
Ref&ence notch
Magnet is installed on the circumferential surface

of rotating disk.
(Circumferential mounting)
The sensor head reference notch should be on the opposite drive side and the magnet
should be installed in the polarity shown below.
Drive side
Opposite
drive side
notch
View from ,,A,
Magnet is installed on the circumferential surfaceof rotating disk.
15 - 1
As long as the relation between location of the sensor head reference notch and the polarity
of the magnet are aligned, the sensor head and the magnet can be installed as shown
below in
, and
normal
orientation
can
be
carried
out.
(However, the parameter SP097 SPEC0 magnesensor detection polarity bit must be
Opposite
drive side
Drive side
notch
View from A
notch
IUNACCEPTABLE EXAMPLE 21
If the sensor head reference notch is not alianed DroDerlv in reference to o
Dolarity
f the maanet,
intense vibration occurs when the sensor head is at the end
of the magnet, and orientation is
imoossible.
+
Opposite drive side
Drive side
Drive side
notch
View from A
Reference notch
1-1
In this example, polarity(N, S)of magnet is inverse

to that in
IV - 65
.
..
1-1
The sensor head reference notch

is on the opposite drive side
of spindle and the polarityof
the magnetis as shown below.
n
Drive
Opposite
drive side
Reference
Opposite
drive side
Drive side
Referen
notch
View from A
notch
(CASE1
As long as the relation between location of sensor head reference notch and the polarity
of
the magnet are aligned, the sensor head and the magnet can be installedbelow
as shown
in
and normal orientation can
be carried out.
(However, the parameterSP097 SPEC0 magnesensor detection polarity bit must
be
1,-
Opposite
drive side
li
V
Reference
notch
i from A
Reference notch
\UNACCEPTABLE EXAMPLE31
W
V
i from A
1-
In this example, polarity(N, S)of magnet is inverse to that in
4.1.3 Caution on installation of magnet

When the magnet is installed to the spindle, pay attention to the following:
Do not place a strong magnetic source near the magnet.
Carefully handle the magnet, avoiding mechanical shock to the magnet.
Secure the magnet to the spindle with appropriate screws.
For appropriate screws, refer to the drawing showing the outside view of magnet in the
Page
IV-69.
After the magnet is installed, balance the entire spindle.
Align the center of the magnet (between
N and S) with the center line of the rotating disk and make
sure the orientation of the magnet and sensor head is as indicated4.1.2
in
to
(Page IV-60 to IV-63).
Keep the magnet clean and keep the peripherals free of iron particles and cut chips (iron particles
may cause malfunction).
Apply lock paint etc. to prevent mounting screw from becoming loose.
If the magnetis installed on a ground rotation disk, demagnetize the disk.
Diameter of rotating disk on which the magnet (other than ring is
type)
installed should be within the
range from 80mm to 120mm.
(10) If speed of the spindle exceeds 6000rpm, use a high speed type, high speed miniature
or high
type
speed ring type magnet.
(11) For details of high speed ring type magnet, refer to the relevant description in IV-69.
the Page
1-1
1-1
4.1.4 Caution on installation of sensor head

When the sensor is
installed, pay attentionto the following:
1-
1-
Install the sensor head in accordance with

4.1.2
to
(Page IV-60 to IV-63).
Align the center line
of the sensor head with the center
of magnet.
The gap between the magnet and the sensor head are listed in1 Table
to Table3.
When a standard type magnet is installed in accordance with
or
refer to
Table 1.
When a highspeed standard magnetis installed in accordance with
or
refer
1-,
1-1
1-
,1-1
to Table 1.
,1-
When a standard magnet is installed in accordance with
refer to Table2.
,1When a high speed miniature magnet is installed in accordance1 -with

1
When a high speed standard magnetis installed in accordance with
refer to Table2.
or ,1-
refer
to Table 3.
For highspeed ring type magnet, refer to the outside view in the Page
IV-69.
* When magnets are mass-produced,
it is recommended to prepare jigs for production.
For connector used in the amplifier, BKO-C1810 type is oil-proof, but
BKO-C1730 is not. It is
recommended to place the connector in an oil-free location.
The cable between the amplifier and the controller should be laid down away from high voltage
cables.
Check the connector wiring, securely engage the receptacle and tighten connector lock screws.
IV - 67
.
-p
I
MO 3
Direction f rotation
MO 3
FaceA
f i
permis!
Magnet
I
Table 1
BKO-Cl810H03
Standard
Radius (R)mm
40
50
60
70
Max. gap
mm
mm
2.7f 0.5
2.8f 0.5
3.0f 0.5
3.4f 0.5
Min. gap
11.5f 0.5
9.5f 0.5
8.5f 0.5
8.0k 0.5
BKO-Cl730H06
High speed standard
Min. gap
Max. gapmm
Table 2
BKO-Cl730H06
High speed standard
Gap mm
40
50
BKO-Cl810H03
Standard
Gap mm
6 k 0.5
6 k 0.5
60
6 f 0.5
5 & 0.5
Radius (R)mm
5 f 0.5
5 f 0.5
Table 3
BKO-CI730H09
Radius (R)mm
40
50
60
70
Max. gapmm
6.25f 0.5
6.0f 0.5
5.75f 0.5
5.5f 0.5
IV - 68
mm
1.22f 0.5
1.31 f 0.5
1.5f 0.5
2.38f 0.5
10 f 0.5
8 f 0.5
7 f 0.5
7 f 0.5
High speed miniature

Min.gap
mm
3.3f 0.5
3.7f 0.5
3.85f 0.5
3.87 0.5
4.1.5 Types and outside dimensions of magnesensor

For oriented spindle stop, the following combinations of amplifier, sensor and magnet
are available.
Permissible
Type
Standard
High-speed
standard
High-speed
miniature
High-speed ring
High-speed ring
High-speed ring
High-speed
ring
I
I
I
Combination
Model
speed [RPMI
0 to 6000
MAGSENSOR BKO-C1810H01-3
0 to 12000
0 to 12000
0 to 25000
0 to 25000
0 to 30000
0 to 30000
I
I
I
MAGSENSOR
BKO-C1730H01.2.6
MAGSENSOR BKO-C1730H01.2.9
1
I
H01
H01
H01
I
1
I
I
H02
H02
H02
MAGSENSORBKO-C1730H01.2.13
Sensor Magnet
Amplifier
H01
H01
H01
I
I
I
I
H03
H09
I
I
H41
H42
H01
H43
H44
H06
H02
H02
H02
H02
I
I
Note: Combination of amplifier, sensor and magnetis possible within thesame modelgroup (C1810 or
C 1730).
Outside dimensions:
0 Amplifier HOI
-+
(sensor
Connector
side)
For BKO-Cl810H01, RWR-8F is used.
For BKO-Cl730HO1, TRC116-21A10-7F is used.
onnedor (controllercable side)

Sensor : TRCl16-21A10-7M
Cable : TRC116-12Al
O-7F10.5
Sensor HO2
Reference
Connector
For MKO-C1810H02, R04-P-8M is used.
For BKO-C1730H02, TRCl16-12A10-7M
is used.
IV - 69
Magnet
Pennissible speed
[RPMI
0 to 6000
Outline drawing
p2+a.3
peference hole
2.
0 to 12000
Weight: 4W 1.!3g
7.5
Mounting screw: M4 screw
Weight: 14.8k 0.79
0 to 12000
Mounting screw: M4 screw

Spun ring
0 to 25000
4-F screw
RI-
0 to 25000
Sen
/-
Reference
notch
Polarity (N,S) is indicate ontheside w a l l ofcase.

Sensor head should be installed
so that the reference
'
notch of sensor head comesthe
oncase side.
Refer to page82 and followingfor details.
Magnet
Unit: mm
Type
0 to 30000
BKO-C1730Hll
BKO-C 1 730H
12
BKO-C1730H13
BKO-C1730H14
Caution on installation of H41-44

1. Tolerance to shaft dimension shouldbe "h6'.
2. 2-0Gholes can be used for positioning of spindle
and magnet.
3. Magnet shall be installed as shown
to the left.
4. Misalignment between sensor head and magnet
center line shallbe within Qmm.
5. NS is indicated on the cover sides. Assembleso
that
the
sensor
head's
reference
groove
comes
to
the case side.
0 to 30000
Installation of magnet
IV - 70
4.2 Encoder orientation (4096 points)

4.2.1 Configuration
N/C
Spindle
IV- 71
4.2.2 Outside dimensions

Tolerable rotation
6000 rpm
Encoder model
RFH-1024-22-1M-68
RFH-1024-22-1M-68-8
Encoder (1024P/rev)
8000 rpm
Name plate
1.153
Key dimensions
Connector
Encoder:
Controller cable:
MS3106A20-29S
135
Unit: mm
1chB C
5. Contour Control (C-axis Control)Encoder
5. Contour Control (C-axisControl) Encoder

5.1 Separate stand-type encoder
5.1.I Name : OSE90K+1024BKO-NC6336H01
5.1.2 Outside dimensions
109=
4-M4,6mm deep
*
I
Caution label
Ti-
onnector
Encoder: MS3102A20-29P
Controller cable:MS3106A20-29S (user should prepare this connector)
Note 1. The max. encoder speed must be set to

6,000rpm or less.
Note 2. The dimensional tolerances that are not
indicated are +0.5mm.
Detailed viewof shaft end
5.1.3Connectors
(1) Connectorside: MS3102A20-29P Controller cable side: MS3106A20-29S
(2) Connection(Notsupplied)
1ch
2ch
3ch
4ch
Remarks
Signal output
1024 CTT
1 Crr
A B phase
Z phase
C D phase
90000 Crr
1 Crr
Y phase
B phase
phase
D phase
phase
IV - 73
(
.
-
. ".
C
D
~~
Function
Ich A phase
2ch Z phase
l c h B phase
CaseGND
3ch D phase
4ch
phase
ov
Admitted electrical speed is 166 rpm for signal in 3 channel (C, D phases,
, b phases)
5.1.4 Mechanical specifications

(1) Rotationalcharacteristics
a.
Inertia
b. Shaft frictional torque
c. Shaft angular acceleration
d. Permissible max. speed
:
:
:
:
Max. 100 gcm2

Max. Ikpcm
Max. 10 rad/sec2
7,030 rpm
(2) Mechanicalconstruction
a. Bearing
b.
c.
Weightd.
e.
f.
: Reoiling
not
isrequired
for
100,000 hr of operation
at
2,000
rpm,
and
20,000 hr of operation at 6,000 rpm.
Shaft
runout
: Max.
0.02mm
at
15mm from shaft end
Permissible load
: 10 kg (5 kg during
operation)
in
thrust
direction
20 kg (10 kg during operation) in radial direction
: Max. 2 kg
Error in perpendicularity of flangesurfaceagainst shaft
1 Max. 0.05 mm
Eccentricity
flange
engagement
in
: Max. 0.05 mm
(3) Environment
a. Operating temperature range

b. Storage temperature range
c.
Humidity
d. Vibration
e. Mechanicalimpact
: -5C +55"C
: -20C +85"C
: 95%PH (at45'C) for 8 hours
: 5 to 50 Hz, 1.5 mm full amplitude,30 min. for eachaxis
: 30G,1Imsec., I O times for each axis
5. Contour Control(C-axis Control) Encoder
5.1.5 Handling, installation and operationof encoder

1.
Installation of encoder
It is recommended that flexible coupling be used to connect the encoder to the spindle shaft to
secure the encoder life and performance.
(1) Installation accuracy
Runout and misalignment in encoder connection should be within the following accuracy.
(2) Recommendedcoupling
Manufacturer
Model
Resonance frequency
Error in position detection
Permissible speed
Misalignment
Outside
dimensions
I Eccentricity
Angular
displacement
Max. length
M=. diameter
Example I
TOKUSHU SEIKO
Model M1
1,374 Hz
Example 2
EAGLE
FCS38A
0.7 mm
3,515 Hz
1.2 X
deg.
10,000 rpm
0.16 mm
1.5 deg.
1.5deg.
74.5 mm
057 mm
33 mm
038 mm
0.8
deg.
20,000rpm
For details, refer to the relevant catalog.

2.
Cable
CAUTION
When manufacturing the detector cable,

do not mistake the connection. Failure to observe this
could lead to runaway of the encoder, andto injuries.

In order to assure the maximum performance
of encoder, note thefollowing:
IV - 75
(1) Power supplyof encoder should be more than14.5V1 .

1) Use larger wiresfor +5V and OV lines.
2) Use two or more wires
for +5V and OV lines.
3) Use a cable as short as possible.
(2) In the connector(MS3106A20-29S) on the encoder side, short-circuit between pins

@ and @,
or @ . (Use a short wire of 0.75 sq. 1.25sq.)
3.
Others
(1) The encoder is a precision device,
so take care not to apply strong shocksit.to
(2) Mistaken wiring may cause trouble. Confirm the connector name and pin Nos., etc., before
wiring.
5.2 Built-in encoder

5.2.1 Model: MBE-9OK
Refer to theMBE-9OK (built-in C axis encoder) SPECIFICATIONS
MANUAL [BNP-A299341].
5.2.2 Model: MHE-9OK

Refer to the MHE-9OK (built-in C axis encoder) SPECIFICATIONS MANUAL [BNP-A2993-44].
IMDS-NB-SP (HI parameters I

User (
)I
Type (
)I
Note:Theparameterswithnosettingarehandledasstandardsettings.
motor
), Spindle
Spindle
amplifier
(-SPStandard
SP039
SP041
PTYP
SP042
CRNG
I SP012 I
ATYP
I 1 6i
11
Standard
Class
SP038 SFNC6
SP043
4
4
.-
cI
Standard
.-
(SJ-
SP068 VIGWB
SP069 VlGN
SP070 I FHz
SP071 I
SP072
SP073
S618
SPO19
SP020
SP021
SP022
ZSP
CSNl
SDTS
TLMl
VGNPl
6000 I
01
01
I
I
0
0
01
01
SP074
TRNG
TRANS SPO44
SP075
SP076
SP077
0
0
14
FONS
TDSL
SP078
SPOl5
I SP017 I TSP
01
01
20
63
SPO84
SP085
SP086
12
SP057
I-Sx[ 1 i I 1
SP031
SP032
GRB2
GRB3
GRB4
Setting
SP090
SPO91
SP093
SP062
110
VGHl
OFSN
60
0
Class Name
Standard
Abbr.
Name
Setting
setting
Abbr.
Standard
Setting
setting
Class
.c
a
d
NBL
Y
I SP321 I RPML
0000
Name
SP325
SP326
Y,
0000
0000
SP300
0000
SP302 I NICNT
SP303 NlCT
NCSN
0000 SP305 NWR1
0000
NWR2
SP307 NWR3
0000 I
SP356
VPWML
0000
PML
OOOO
SP357
SP358
SP359 1
SP360
SP361
SP363
ooool
SP367
OOOOI
0000
SP335
SP336
KDlL
KQPL
0000
SP337
SP338
SP339
KQlL
IDSML
IQSML
~1
0000
NEVO
NEVl
SP308
SP309
/spy2/
ooool
ooool
SIQ
DPO
DBS
k
P
3
E
1DIQ
I SP320 I BSD
SP343
SP344
0000
00o0
oo00
ooool
OOOol
OOOO
TMLRL
TMLDL
TMLSL
OOOol
0000
0000
0000
SP370
SP371
I ooi 1
I SP341 I KVQSL I
0000
I SP310
I SP311
I SP312
I SP313
I SP314 SPO
I~ ~ 3 1I %SBS
SP316
SP317
SP318
~~
Standard
Setting
setting
OOOO
0000
0000
NRL
NFL
~~
SP297
SP298
SP299
Abbr.
1 I 1 0 01 I
SP323
NPL
SP324
SP322
OOOOl
0000
SP372
SP373
SP374 I
sp375 1
I
I
OOOol
OOOol
SP377
SP378
SP379
SP380
SP381
SP382
EDOL
SPOL
SBSL
DBSL
oooo
oooo
oooo
oooo
oooo
SP383
DlQL
BSDL
OOOO
OOOO
SP384
SlQL
DPOL
0000

Maintenance Manual For Mitsubishi AC Servo and Spindle Controller CMDSMA1100E

Uploaded by

Copyright:

Available Formats

Maintenance Manual For Mitsubishi AC Servo and Spindle Controller CMDSMA1100E

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Maintenance Manual For Mitsubishi AC Servo and Spindle Controller CMDSMA1100E

Uploaded by

Copyright:

Available Formats

Maintenance Manual

This Manual is published to assist experienced personnel on the operation, maintenance

The machine is provided with a number of safety

AFTER CONTROL POWER IS TURNED ON

4) Tools and other items around the machine or

NOTE: USE OF THE FOLLOWING LOCKOUT PROCEDURE IS MANDATORY WHEN COMPLETING

THE LOCKOUT PROCESS MUST BE PERFORMED BY AUTHORIZED PERSONNEL ONLY.

SHUT OFF MACHINE POWER USING NORMAL SHUT DOWN PROCEDURES.

COMPLETE THE REQUIRED MAINTENANCE OPERATIONS.

MAKE SURE ALL PERSONNEL ARE CLEAR OF THE MACHINE.

In pouring grout, fasten the leveling block

Desirable Independent Grounding:

VERIFY THE ACTUAL MACHINE ELECTRICAL

POWER REQUIREMENT AND THE MAIN

A step-down transformer is optional on some machine models. Be certain to

FAILURE TO COMPLY CAN RESULT IN PERSONAL INJURY AND DAMAGE TO THE

MAZATROL CNC CONTROLLERS PROVIDE PARAMETER SETTINGS TO LIMIT SPINDLE

MAZAK MACHINES ARE ENGINEERED WITH A NUMBER OF SAFETY DEVICES TO

MAZAK MACHINES ARE ENGINEERED WITH A NUMBER OF SAFETY DEVICES TO

BEFORE STARTING OPERATION, CHECK THAT THE WORKPIECE IS SECURELY MOUNTED

CONFIRM PROPER WORKPIECE FIXTURING/CLAMPING, TOOL SETUP AND THAT THE

CUTTING CONDITIONS SUGGESTED BY THE MACHINING NAVAGATION FUNCTION

CUTTING CONDITIONS FOR TOOLS THAT ARE SUGGESTED TO BE USED BY THE

FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO

Determined by YMW Eng. H.Q. 99/9/1

Prohibit cycle start.

Prohibit cycle start.

Limit the rapid override. Max is 12%.

Prohibit cycle start.

Can not run auto operation.

Can operate CHUCK, TAILSLEEVE ,

Can operate CHUCK, TAILSLEEVE ,

Can NOT operate Spindle, Axis, Turret,

Can not operate Spindle running, but

Can operate CHUCK, TAILSLEEVE ,

Can operate CHUCK, TAILSLEEVE ,

Can not run Auto-operation.

The Other Thoroughbred From Kentucky

How well is the documentation suited to your needs?

Were you able to find the necessary information easily?

How easy are the manuals to understand?

Overall, how do you rate the documentation?

Precautions for safety

When a dangeroussituation may occur if handling is mistaken

may lead to major results depending on

The numeric control unit is configured

Changes in terminal names

For Safe Use

Do not open the front cover whole the power

Do not remove the front cover even when the power

Ground the servo amplifier and servomotor

Wait at leastI O minutes after turning the power

Wiring and inspecbon

Do not touch the switches

Servo System Section

Compatible detectors and compatible motors ............................................

2 Adjustment Procedure ..............................................................................................

2.1 Initial adjustment .................................................................................................