Nitokit Surface Sealant

Nitokit Surface Sealant
constructive solutions
Epoxy resin sealant and resurfacing

compound
Uses
Mixing
Sealing cracks externally.
Mix both components till a homogeneous mixture is

obtained. It is important that both components are
intermixed thoroughly and that no traces of the
components remain unmixed. Total mixing time 3 to 5
minutes. Apply sealant using spatula, palette knife,
Swedish knife or squeeze.
Fixing injection packers.

Levelling concrete surface irregularities.
Adhesive for bonding steel plates to concrete.
Properties
Used in conjunction with Nitokit injection system.
Colour:
Specific gravity:
Volume solid:
Minimum application
temperature:
Pot life:
As a general multi-purpose epoxy paste adhesive.

Description
Nitokit Surface Sealant, a two part filled epoxy, is an
accessory to the Nitokit epoxy resin, and Conbextra
Injection System. Nitokit Surface Sealant is used to seal
over the cracks in structural materials such as concrete.
The seal prevents flow-out of resin when injected into the
cracks. Nitokit Surface Sealant is also used to bond
injection nipples to the surface of the cracks. It is also
used in evening out substrates and filling blow-holes prior
to applying floor and wall epoxy and urethane based
coating and toppings.
Full cure:
Maximum service
temperature:
Bond strength:
Clean the surface and remove any dust, unsound or

contaminated material, plaster, oil, paint, grease,
corrosion deposits or algae.
Surface preparation
Surface should preferably be prepared using high

pressure water jetting or light abrasive blasting, followed
by thorough washing to remove dust and remaining
particles.
Nitokit Surface Sealant has to retain the injection system

under pressure. Care must be taken to provide a bond
surface which is clean, dry and sound.
3.
+ 70oC
> cohesive strength of
concrete
Preparation
Instruction for use
2.
5oC
o
2 hours at 20 C
hour at 30oC
o
4 days at 30 C
Application instructions
Nitokit Surface Sealant consists of two parts thixotropic,

solvent free, epoxy resin compound of grey colour.
1.
Grey
1.75
100%
Oil and grease deposits should be removed by steam

cleaning, detergent scrubbing or the use of a proprietary
degreaser. The effectiveness of decontamination should
then be assessed by a pull-off test. No independent
priming system is required.
Remove heavy deposits of grease and dirt by

scrubbing with Fosroc Chemical Degreaser and
washed with plenty of clean water to ensure complete
removal of oil and grease. Dirt alone may be
removed with wire brushes or similar mechanical
means. Both surface and cracks must be allowed to
dry thoroughly.
Curing
Allow the sealant to cure for at least 8 hours at 35oC
before injecting Nitokit epoxy resin injection system.
Remove deteriorated concrete, laitance and paint.

The best treatment is commercial shot blasting with
sand, steel-shot or a proprietary abrasive. Where
shot blasting is impracticable, use rotary wire
brushes, sander or cup grinders.
Note: At low ambient temperature the curing time must

be extended in order to allow sufficient strength to build up
in sealant.
Blow the cracks and treated surfaces with a clean dry

(filtered) compressed air-blast to ensure complete
removal of all dust and loose particles.
A fast set grade is available on request.
Page 1
Nitokit Surface Sealant

Removal of cured sealant
Packaging
After the Nitokit system has set, the sealant may be ground
or sanded off or, alternatively, softened with a hot air blower
and pared off.
Nitokit Surface Sealant:

Fosroc Solvent 102
1 kg and 5 kg
4 litre can
Coverage
Make good any depressions or damaged areas with further

quantities of surface sealant.
Cleaning
2
1.75 kg/m /mm thickness
Recoatability
Tools and equipment should be cleaned with Fosroc

Solvent 102 immediately after use.
Recoatable with all coatings based on epoxy and coal

tar epoxy within a maximum interval of 48 hours.
Precautions
Supply
Health and safety
Reference should be made to our local Sales Department

Staff or Local Agents. Contract supplies may be arranged
with the factory in Jeddah.
Some people are sensitive to epoxy resins so gloves and

barrier cream, Vaseline, Kerodex 71, Rozalex 9, Debba-wet
work or similar, should be used when handling these
products. If contact with the resin occurs, it must be
removed, before it hardens, with resin removing cream such
as Kerocleanse 22, and Rozalex 42 followed by washing
with soap and water. Do not use solvent.
Technical Service
An advisory service is maintained from Jeddah for on-site
assistance and advice on the use of Fosam product range.
This service is supported by a team of Specialists in the
field.
Provide adequate ventilation during application and curing

process.
Additional information
Fire
Nitokit Surface Sealant is flammable.
naked flames or smoke during use.
Technical data and guidance can be provided on a wide

range of admixtures and concreting aids including,
Accelerators, Retarders, Waterroofers, Mould Release
Agents, Surface Retarders, Workability aids and Repair
materials.
Do not use near
Flash point
Fosroc Solvent 102
60oC
32oC
Storage
Shelf life 12 months if stored in a dry and cool place, below
25oC.
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
Fosam Company Limited

Head Office
Post Box 11081
Jeddah 21453
Saudi Arabia
www.fosroc.com
Telephone: +966 2 637 5345
Fax: +966 2 637 5891
email: fosam@fosroc.com
Regional Offices
Jeddah Sales Office
Jeddah Showroom
Riyadh
Dammam
Khamis Mushayt
Tel: (02) 6080999

Tel: (02) 665 0787
Tel: (01) 482 9303
Tel: (03) 814 1282
Tel: (07) 250 0469
Fax: (02) 635 3330 Yanbu Tel: (04) 322 4280

Fax: (02) 667 4884 Makkah Tel: (02) 542 0869
Fax: (01) 482 7562 Medinah Tel: (04) 845 1767
Fax: (03) 814 1581 Jubail
Tel: (03) 362 3904
Fax: (07) 250 0469
Fax: (04) 391 2980

Fax: (02) 542 0869
Fax: (04) 846 3195
Fax: (03) 362 3875
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 2
FO SA/NKSS/05/B

Nitokit Surface Sealant

Uploaded by

Copyright:

Available Formats

Nitokit Surface Sealant

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Nitokit Surface Sealant

Uploaded by

Copyright:

Available Formats

Nitokit Surface Sealant

Epoxy resin sealant and resurfacing

Sealing cracks externally.

Mix both components till a homogeneous mixture is

Fixing injection packers.

Used in conjunction with Nitokit injection system.

As a general multi-purpose epoxy paste adhesive.

Clean the surface and remove any dust, unsound or

Surface should preferably be prepared using high

Nitokit Surface Sealant has to retain the injection system

Instruction for use

Nitokit Surface Sealant consists of two parts thixotropic,

Oil and grease deposits should be removed by steam

Remove heavy deposits of grease and dirt by

Remove deteriorated concrete, laitance and paint.

Note: At low ambient temperature the curing time must

Blow the cracks and treated surfaces with a clean dry

A fast set grade is available on request.

Nitokit Surface Sealant

Nitokit Surface Sealant:

Make good any depressions or damaged areas with further

Nitokit Surface Sealant:

Tools and equipment should be cleaned with Fosroc

Recoatable with all coatings based on epoxy and coal

Health and safety

Reference should be made to our local Sales Department

Some people are sensitive to epoxy resins so gloves and

Provide adequate ventilation during application and curing

Technical data and guidance can be provided on a wide

Do not use near

Fosam Company Limited

Telephone: +966 2 637 5345

Fax: +966 2 637 5891

Tel: (02) 6080999

Fax: (02) 635 3330 Yanbu Tel: (04) 322 4280

Fax: (04) 391 2980

You might also like