Conplast PA211: Water Reducing Admixture

Conplast PA211
constructive solutions
Water reducing admixture

Uses
Dosage
To improve the effectiveness of the water content of a

concrete mix.
At higher dosages to provide a cost effective means of

reducing concrete permeability and thereby reducing
water penetration.
The optimum dosage of Conplast P211 to meet specific

requirements should always be determined by trials using
the material and conditions that will be experienced in use.
The normal dosage range is 0.4 to 0.8 litres/100 kg of
cementitious material, including PFA, GGBFS and microsilica.
Use at other dosages
Advantages
Allows specified strength grades to be met at reduced

cement content or increased workability.
Water reduction significantly improves compressive

strengths at all ages and enhances durability through
the production of low permeability concrete.
Minimises the risk of segregation and bleeding and

assists in the production of a dense, close textured
surface, improving durability.
Chloride free, safe for use in pre-stressed and

reinforced concrete.
Standard compliance
Dosages outside the normal ranges quoted above can be

used to meet particular mix requirements. Contact Fosroc
for advice in these cases.
Properties
Appearance:
Specific gravity:
Chloride content:
Air entrainment:
Alkali content:
Brown liquid
o
Typically 1.17 at 20 C
Nil to BS 5075
Typically less than 2% additional air
is entrained at normal dosages
Typically less than 5.0 g. Na2O
equivalent/litre of admixture. A fact
sheet on this subject is available.
Instruction for use
Conplast P211 complies with BS 5075 Part 1 and with

ASTM C-494 as Type A.
Compatibility
Conplast P211 complies with the requirements of the United

Kingdom Water Fittings Byelaws Scheme and is listed in the
Directory of Materials as suitable for use in contact with
potable water under its previous name of Conplast P211.
Conplast P211 is compatible with other Fosroc admixtures

in the same concrete mix. All admixtures should be added
to the concrete separately and must not be mixed together
prior to addition. The performance of concrete containing
more than one admixture should be assessed by trial mixes.
Description
Conplast P211 is a chloride free water-reducing admixture
based on selected sugar-reduced lignosulphonates. It is
supplied as a brown solution which instantly disperses in
water.
Conplast P211 disperses the fine particles in the concrete
mix, enabling the water content of the concrete to perform
more effectively and improving the consistency of the
concrete. This produces higher levels of workability for the
same water content, allowing benefits such as water
reduction and increased strengths to be taken.
Technical support
Fosroc provides a technical advisory service for on-site
assistance and advice on mix design, admixture selection,
evaluation trials and dispensing equipment.
Conplast P211 is suitable for use with all types of ordinary

Portland cements and cement replacement materials such
as PFA, GGBFS and micro-silica.
Dispensing
The correct quantity of Conplast P211 should be measured
by means of a recommended dispenser. The admixture
should then be added to the concrete with the mixing water
to obtain the best results. Contact Fosroc for advice
regarding suitable equipment and its installation.
Effects of overdosing
An overdose of double the intended amount of Conplast
P211 will result in an increase in retardation as compared to
that normally obtained at the intended dosage. Provided
that adequate curing is maintained, the ultimate strength of
the concrete will not be impaired by increased retardation
and will generally be increased. The effects of overdosing
will be further increased if sulphate resisting cement or
cement replacement materials are used.
Page 1
Conplast PA211
Over-dosage may also cause increased air entrainment,
which will tend to reduce strength. The degree of this effect
will depend on the particular mix design and overdose level.
Fire
Estimating - Packaging
Cleaning and disposal
Conplast P211 is available in drum or bulk supply.

larger users, storage tanks can be supplied.
For
Storage
Conplast P211 has a minimum shelf life of 12 months
o
provided the temperature is kept within the range of 2 C to
o
50 C. Should the temperature of the product fall outside
this range then contact Fosroc for advice.
Freezing point: Approximately 3oC
Conplast P211 is water based and non-flammable.
Spillages of Conplast P211 should be absorbed onto sand,

earth or vermiculite and transferred to suitable containers.
Remnants should be hosed down with large quantities of
water.
The disposal of excess or waste material should be carried
out in accordance with local legislation under the guidance
of the local waste regulatory authority.
Additional information
Conplast P211 was previously known as Conplast 211.
Precautions
Note 1: CPL Regulations 1984 Supply Schedule 1

Note 2: HSE Publication Guidance Note EH40
Health and safety

Conplast P211 does not fall into the hazard classifications of
current regulations (see notes 1 and 2 below). However, it
should not be swallowed or allowed to come into contact
with skin and eyes.
Suitable protective gloves and goggles should be worn.
Splashes on the skin should be removed with water. In
case of contact with eyes rinse immediately with plenty of
water and seek medical advice. If swallowed seek medical
attention immediately do not induce vomiting.
For further information consult the Material Safety Data
Sheet available for this product.
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
Fosam Company Limited

Head Office
Post Box 11081
Jeddah - 21453
Saudi Arabia
www.fosroc.com
Telephone: +966 2 637 5345
Fax: +966 2 637 5891
email: fosam@fosroc.com
Regional Offices
Jeddah Sales Office
Jeddah Showroom
Riyadh
Dammam
Khamis Mushayt
Tel: (02) 608 0999

Tel: (02) 665 0187
Tel: (01) 482 9303
Tel: (03) 814 1282
Tel: (07) 250 0469
Fax: (02) 635 3330

Fax: (02) 667 4844
Fax: (01) 482 7562
Fax: (03) 814 1581
Fax: (07) 250 0469
Yanbu Tel: (04) 322 4280

Makkah Tel: (02) 542 0869
Medinah Tel: (04) 845 1767
Jubail Tel: (03) 362 3904
Fax: (04) 391 2980

Fax: (02) 542 0869
Fax: (04) 846 3195
Fax: (03) 362 3875
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 2
FO SA/CONPLAST PA211/05/A

Conplast PA211: Water Reducing Admixture

Uploaded by

Copyright:

Available Formats

Conplast PA211: Water Reducing Admixture

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Conplast PA211: Water Reducing Admixture

Uploaded by

Copyright:

Available Formats

Conplast PA211

Water reducing admixture

To improve the effectiveness of the water content of a

At higher dosages to provide a cost effective means of

The optimum dosage of Conplast P211 to meet specific

Allows specified strength grades to be met at reduced

Water reduction significantly improves compressive

Minimises the risk of segregation and bleeding and

Chloride free, safe for use in pre-stressed and

Dosages outside the normal ranges quoted above can be

Instruction for use

Conplast P211 complies with BS 5075 Part 1 and with

Conplast P211 complies with the requirements of the United

Conplast P211 is compatible with other Fosroc admixtures

Conplast P211 is suitable for use with all types of ordinary

Cleaning and disposal

Conplast P211 is available in drum or bulk supply.

Conplast P211 is water based and non-flammable.

Spillages of Conplast P211 should be absorbed onto sand,

Note 1: CPL Regulations 1984 Supply Schedule 1

Health and safety

Fosam Company Limited

Telephone: +966 2 637 5345

Fax: +966 2 637 5891

Tel: (02) 608 0999

Fax: (02) 635 3330

Yanbu Tel: (04) 322 4280

Fax: (04) 391 2980

You might also like