Viewsonic Vg1930wm-1 SM

Service Manual
ViewSonic VG1930wm-1
Model No. VS11354
19 Color TFT LCD Display
(VG1930wm-1_SM Rev. 1a Oct. 2006)
ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright
Copyright 2006 by ViewSonic Corporation. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranty of merchantability or fitness for any
particular purpose. Further, ViewSonic reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation of ViewSonic to notify any
person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision
SM Editing Date
1a
10/25/2006
ViewSonic Corporation
ECR Number
Description of Changes
Initial Release
Editor
Jamie Chang
Confidential - Do Not Copy
VG1930wm-1
TABLE OF CONTENTS
1.
Precautions and Safety Notices
2.
Specification
3.
Front Panel Function Control Description
11
4.
Circuit Description
17
5.
Adjustment Procedure
28
6.
Troubleshooting Flow Chart
39
7.
Recommended Spare Parts List
47
8.
Exploded Diagram and Exploded Parts List
49
9.
Block Diagram
52
10. Schematic Diagrams
53
11. PCB Layout Diagrams
60
ii
VG1930wm-1
1. Precautions and Safety Notices

1. SAFETY PRECAUTIONS
This monitor is manufactured and tested on a ground principle that a users safety comes first. However,
improper used or installation may cause damage to the monitor as well as to the user.
WARNINGS:
This monitor should be operated only at the correct power sources indicated on the label on the rear of the
monitor. If youre unsure of the power supply in you residence, consult your local dealer or Power Company.
Use only the special power adapter that comes with this monitor for power input.
Do not try to repair the monitor by yourself, as it contains no user-serviceable parts. Only the qualified
technician can repair it.
Do not remove the monitor cabinet. There are high-voltage parts inside that may cause electric shock to
human bodies.
Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.
Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power cable immediately and
consult your closed dealer.
Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply non-ammonia
based cleaner onto the cloth, not directly onto the glass screen.
Do not place heavy objects on the monitor or power cord.
2. PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety visual inspections and the protection
afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage,
wattage, etc. Before replacing any of these components read the parts list in this manual carefully. The use of
substitute replacement parts, which do not have the same safety characteristics as specified in the parts list,
may create shock, fire, or other hazards.
3. SERVICE NOTES
When replacing parts or circuit boards, clamp the lead wires around terminals before soldering.
Keep wires away from high voltage, high temperature components and sharp edges.
Keep wires in their original position so as to reduce interference.
Adjustment of this product please refers to the user manual.
VG1930wm-1
4. Handling and Placing Methods
VG1930wm-1
VG1930wm-1
2. Specification
1. INTPRODUCTION
VG1930wm
FEATURES
19 w
Size
300 cd/
Luminance (Typ)
TFTLCD PANEL
Contrast Ratio (Typ)
700:1
Colors (6 bits + 2 bits FRC)
16.2 M
Response Time (Typ)
5 ms
Viewing Angle (H/V)
160 / 160 @>=10
Recommend resolution
Input Signal
Sync Compatibility
Compatibility
Power Voltage
Power Consumption
1440x900@60Hz
Analog (75ohms, 0.7/1.0 Vp-p)
Yes
Digital
Yes
Separate Sync
Yes
Composite Sync
Yes
Sync on Green
Yes
PC
Yes
Power Mac
Yes
TV Box (NextVision 6)
Yes
AC 100-240V, 50/60Hz
Yes
On Mode(Max / Typ)
43 W/38W
1 W
Off Mode (Max)
Audio
Ergonomics
OSD Control
Dimension
Weight
Operating Condition
Storage Condition
Yes
Tilt ( 20 - -5 )
Yes
Swivel
Yes
Pivot
No
Height Adjust
Yes
[ 1 ] [ 2 ] [ ][] []
Yes
Physical (W x H x D)
460 x 434 x 230 mm
Package (W x H x D)
560 x 525 x 282 mm
Physical (Net Weight)
5.4 kg
Package (Gross Weight)
6.9 kg
Temperature (/)
32-104 / 0-40
Humidity (%)
10 % - 90 %
Temperature (/)
-4-140 / -20-60
Humidity (%)
10% - 90 %
UL, CUL, FCC-B (ICES), CB, CE, TCO'03, ICES-003B, ISO13406-2, TUV/GS,
Regulation
TUV ERGO(covers ISO13406-2 & MPRII), TUV-S, NOM, GOST-R, HYGIENIC

(20 copies), ENERGY, Energy Star, CCC, BSMI, PSB, C-TICK, KTL/MIC,
SASO, WEEE, RoHS
VG1930wm-1
2 GENERAL specification
Test Resolution & Frequency
1440x900 @ 60Hz
Test Image Size
Full Size
Contrast and Brightness Controls
Factory Default:
Contrast = 70%, Brightness = 100%
VIDEO INTERFACE
Analog Input Connector
Video Cable Strain Relief
DB-15 (Analog), refer the appendix A

Equal to twice the weight of the monitor for five
minutes
Video Cable Connector DB-15 Pin out
Compliant DDC 1/2B
Video Signals
Video RGB (Analog) Separate,
Video Impedance
75 Ohms (Analog)
Maximum PC Video Signal
950 mV with no damage to monitor
Maximum Mac Video Signal
1250 mV with no damage to monitor
DDC 1/2B
Compliant with Revision 1.3
Sync Compatibility
Separate Sync
Video Compatibility
Shall be compatible with all PC type computers,

Macintosh computers, and after market video cards
640 x 350, 640 x 480, 720 x 400 (640 x 400*), 800 x
Resolution Compatibility
600, 832 x 624, 1024 x 768, 1152 x 864, 1280 x 960,

1280 x 1024,1440x900
Exclusions
Not compatible with interlaced video
POWER SUPPLY
Internal Power Supply
Part Number:RLPR-025
Input Voltage Range
90 to 264 VAC
Input Frequency Range
47 to 63 Hertz
Short Circuit Protection
OUTPUT CAN BE SHORTED WITHOUT DAMAGE
Over Current Protection
4 A TYPICAL AT 14.2 VDC
Leakage Current
3.5MA (MAX) AT 254VAC / 60HZ
Efficiency
80% TYPICAL AT 115VAC FULL LOAD
Fuse
INTERNAL AND NOT USER REPLACEABLE
Power Dissipation
38 WATTS (TYP)
Max Input AC Current
0.8 ARMS @ 90VAC, 0.4 ARMS @265VAC
Inrush Current (Cold Start)
40 A @ 120VAC, 60 A (MAX) @ 220VAC

SHALL START AND FUNCTION PROPERLY WHEN
UNDER FULL LOAD, WITH ALL COMBINATIONS
Power Supply Cold Start
VG1930wm-1
Power Supply Transient Immunity

Power Supply Line Surge Immunity
OF INPUT VOLTAGE, INPUT FREQUENCY, AND

OPERATING TEMPERATURE
SHALL BE ABLE TO WITHSTAND AN ANSI/IEEE
C62.41-1980 2000V 200 AMPERE RING WAVE
TRANSIENT TEST WITH NO DAMAGE
Shall be able to withstand 1.5 times nominal line
voltage for one cycle with no damage
Shall be able to function properly, without reset or
Power Supply Missing Cycle Immunity
visible screen artifacts, when cycle of AC power is

randomly missing at nominal input
The power supply shall not produce audible noise
that would be detectable by the user. Audible shall
Power Supply Acoustics
be defined to be in compliance with ISO 7779 (DIN

EN27779:1991) Noise measurements of machines
acoustics.
Power
Switch
noise
shall
not
be
considered
Separate 3-prong NEMA 5-15P type plug. Length =
US Type Power Cable
1.8m. Connects to display.

Color = Black
Schuko CEE7-7 type plug.
European Type Power Cable
Length = 1.8m, Connects to display.

Color = Black
Separate 3-prong type plug.

CCC Type Power Cable
Length = 1.8m. Connects to display.

Color = Black
Separate 2-prong NEMA 1-15P type plug. Length =
PSE Type Power Cable
1.8m. Connects to display.

Color = Black
Power Saving Operation(Method)

Power Consumption
Recovery Time
VESA DPMS Signaling

On Mode <42 W (max)
Off Mode< 1W
On Mode = N/A, Active Off < 3 sec
ELECTRICAL REQUIREMENT
Horizontal / Vertical Frequency

Horizontal Frequency
30 82 kHz
50 75* Hz.
Vertical Refresh Rate

Maximum Pixel Clock
135 MHz
VG1930wm-1
Sync Polarity
Independent of sync polarity.
Timing Table
SOG
Timing
Composite
Separated
Item
Digital - TMDS
Analog
Remark
640 x 350@70Hz,31.5KHz
640 x 400@60Hz,31.5KHz
640 x 400@70Hz,31.5KHz
640 x 480@50Hz,24.7KHz
640 x 480@60Hz,31.5KHz
DMT
640 x 480@67Hz,35KHz
For MAC
640 x 480@72Hz,37.9KHz
DMT
640 x 480@75Hz,37.5KHz
DMT
720 x 400@70Hz,31.5KHz
10
720 x 480@60Hz,31.5KHz
DTV
11
720 x 576@50Hz,31.3KHz
DTV
12
800 x 600@56Hz,35.1KHz
DMT
13
800 x 600@60Hz,37.9KHz
DMT
14
800 x 600@72Hz,48.1KHz
DMT
15
800 x 600@75Hz,46.9KHz
DMT
16
832 x 624@75Hz,49.7KHz
MAC
17
1024 x 768@50Hz,39.6KHz
18
1024 x 768@60Hz,48.4KHz
DMT
19
1024 x 768@70Hz,56.5KHz
DMT
20
1024 x 768@72Hz,58.1KHz
21
1024 x 768@75Hz,60KHz
DMT
22
1024 x 768@75Hz,60.2KHz
For MAC
23
1152 x 864@75Hz,67.5KHz
DMT
24
1152 x 870@75Hz,68.7KHz
For MAC
25
1152 x 900@67Hz,62.5KHz
For SUN
26
1280 x 720@50Hz,37.5KHz
DTV
27
1280 x 720@60Hz,45KHz
DTV
28
1280 x 768@50Hz,39.6KHz
29
1280 x 768@60Hz,47.8KHz
DMT;
30
1280 x 768@75Hz,60.3KHz
DMT;
31
1280 x 960@50Hz,49.4KHz
32
1280 x 960@60Hz,59.7KHz
DMT
DMT
VG1930wm-1
33
1280 x 960@75Hz,75.2KHz
34
1280 x 1024@50Hz,52.7KHz
35
1280 x 1024@60Hz,64KHz
DMT
36
1280 x 1024@75Hz,80KHz
DMT
37
1440 x 900@60Hz59.9KHz
DMT
Primary Presets
1440x900 @ 60Hz
User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration
Changing Modes
Maximum Mode Change Blank Time for image stability: 3 seconds (Max), excluding Auto Image Adjust time.
Under DOS mode (640 x 350, 720 x 400 & 640 x 400), it should recall factory setting when execute Auto Image
Adjust.
The monitor needs to do Auto Image Adjust the first time when a new mode is detected. (See section 0-Touch
Function Actions)
FRONT PANEL CONTROLS AND INDICATORS
Front Panel Hardware Controls

Power Switch (Front Head)
Power Control, soft Power Switch.

Green ON
Power LED (Front Head)
Orange Active Off

Dark = Soft Power Switch OFF
[;X] Mute
[ ] Power
[ 1 ] Button 1
Front Panel Controls (Head)

[ ] [ 1 ] [ 2 ] [] []
[ 2 ] Button 2
[] Up arrow button
[] Down arrow button
Note: Power Button, Button 1 and Button 2 must be
one-shot logic operation. (i.e. there should be no
cycling)
OSD must fully appear within 0.5s after pushing Button
Reaction Time
Short Cuts Function from the button(s)

[1]
Main Menu
[2]
Input toggle (Analog or Digital; refer to Appendix D)
VG1930wm-1
[]
Brightness adjust
[]
Contrast adjust
[]+ []
recall both of Contrast and Brightness to default
[1] + [2]
toggle 720x400 and 640x400 mode when input 720x400 or

640x400 mode
[1] + [] + []
White Balance. (Not shown on users guide)
[1] + []
Power Lock
[1] + []
OSD Lock
[1] + [] + [2]
[]+ [ ] + Main Power On
Disable Theft Defence function

All reset
No signal + [ ] + [2]+ Main Power on
Burning mode
Signal + [2] + [ ] + Main Power On
Factory Mode
Remark : All the short cuts function are only available while OSD off
Main Menu Controls

The Main Menu OSD includes most of control functions.
Please refer to APPENDIX C (Main Menu OSD Table) for the detail.
Function descriptions
OSD Lock short cuts function for the buttons
The OSD lock will be activated by pressing the front panel control buttons "(1), & ()" for 10 seconds. If
the user then tries to access the OSD by pressing any of the buttons "1", "", "", "2" a message will
appear on the screen for 3 seconds showing "OSD Locked". The OSD lock will be deactivated by
pressing the front panel control buttons "(1), & ()" again for 10 seconds.
Note1: When the OSD is locked will lock all functions, including Volume and Mute
Note 2: Status bar indicating OSD Lock or Unlock is in progress and when complete it will indicate OSD
Locked
Note 3: OSD Lock should not lock Power Button and Power Lock function
Power Lock short cuts function for the buttons

The power button lock will be activated by pressing the front panel control buttons "(1), & ()" for 10
seconds. Locking the power button means that the user won't be able to turn off the LCD while the power
button is locked. If the user presses the power button while it is locked, a message will appear on the
screen for 3 seconds showing "Power Button Locked". It also means that with the power button locked,
the LCD would automatically turn back "On" when power is restored after a power failure. If the power
button is not in the locked mode, then power should return to it's previous state when power is restored
after a power failure. The power button lock will be deactivated by pressing the front panel control buttons
"(1), & ()" again for 10 seconds.
Note 1: Status bar indicating Power Button lock or unlock is in progress and when complete it will
VG1930wm-1
indicate Power Button Locked

Note 2: Power should only be lockable in the On State
Memory Recall Actions
Memory Recall action on the analog and digital mode as below
1. Recall white balance to factory setting
2. Set the factory defaults as shown in Section 4-8
3. Clean all the mode setting buffer
4. Execute Auto Image Adjust
Note: Memory Recall should have no effect for Language, Power Lock, User Color Settings or Input
Priority
Resolution Notice Actions
1. Resolution Notice OSD should show on screen after changing to non-native mode for 30 sec
2. For auto input select function, it shall meet the requirement in Appendix D.
3. The OSD should disappear after 10 sec or by pushing button [1] or [2]
Resolution Notice function should be disabled when push button [2] under Resolution Notice OSD
0-Touch Function Actions
1. Execute Auto Image Adjust when new mode detected, and save the settings to buffer for further use
2. It should be reset by Memory Recall function(Should not reset by power off, power unplug and others)
OSD Auto Save
The OSD shall save new settings when it is turned off by the user or when it times out. There shall not
be a separate save
10
VG1930wm-1
3. Front Panel Function Control Description
Main Menu
with OSD controls
Front Control Panel

shown below in detail
Standby Power On/Off

Power light
Blue = ON
Orange = Power Saving
Audio Mute button turns the sound off

Displays the Main Menu or exits the control screen and saves
adjustments.
Scrolls through menu options and adjusts the displayed control.

Also a shortcut to display the Contrast adjustment control screen.
Displays the control screen for the highlighted control.
Also toggles between two controls on some screens.
Also a shortcut to toggle analog and digital connection.
11
VG1930wm-1
Do the following to adjust the display setting:

1. To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 15
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2. To select a control to adjust, pressSorTto scroll up or down in the Main Menu.
3. After the desired control is selected, press button [2]. A control screen like the one shown
below appears.
The command line at the bottom of the
control screen tells what to do next from
this screen. You can toggle between control
screens, adjust the selected option, or exit
the screen.
4. To adjust the setting, press the up S or down T buttons.

5. To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:
Adjust the computer's graphics card so that it outputs a 1440 x 900 @ 60Hz video signal to
the LCD display. (Look for instructions on changing the refresh rate in the graphics card's
user guide.)
If necessary, make small adjustments using H. POSITION and V. POSITION until the
screen image is completely visible. (The black border around the edge of the screen should
barely touch the illuminated active area of the LCD display.)
12
VG1930wm-1
Main Menu Controls

Adjust the menu items shown below by using the up S and down T buttons.
Control
Explanation
Auto Image Adjust sizes and centers the screen image automatically.
Contrast adjusts the difference between the image background (black level)
and the foreground (white level).
Brightness adjusts background black level of the screen image.
Input Select toggles between inputs if you have more than one computer
connected to the VG1930wm.
Audio Adjust
Volume increases the volume, decreases the volume, and mutes the audio.
Mute temporarily silences audio output.
Color Adjust provides several color adjustment modes, including preset color
temperatures and a User Color mode which allows independent adjustment of
red (R), green (G), and blue (B). The factory setting for this product is 6500K
(6500 Kelvin).
sRGB-This is quickly becoming the industry standard for color management,

with support being included in many of the latest applications. Enabling this
setting allows the LCD display to more accurately display colors the way they
were originally intended. Enabling the sRGB setting will cause the Contrast and
Brightness adjustments to be disabled.
13
VG1930wm-1
Control
Explanation
9300K-Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).
6500K-Adds red to the screen image for warmer white and richer red.
5400K-Adds green to the screen image for a darker color.
5000K-Adds blue and green to the screen image for a darker color.
User Color Individual adjustments for red (R), green (G), and blue (B).
1. To select color (R, G or B) press button [2].
2. To adjust selected color, pressSandT.
Important: If you select RECALL from the Main Menu when the product is
set to a Preset Timing Mode, colors return to the 6500K factory preset.
Information displays the timing mode (video signal input) coming from the
graphics card in the computer, the LCD model number, the serial number, and
the ViewSonic website URL. See your graphics cards user guide for
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1440 x 900 @ 60Hz (recommended) means that the resolution is
1440 x 900 and the refresh rate is 60 Hertz.
Manual Image Adjust Sub-menu
14
VG1930wm-1
Control
Explanation
H. Size (Horizontal Size) adjusts the width of the screen image.

H./V. Position (Horizontal/Vertical Position) moves the screen image left or
right and up or down.
Fine Tune sharpens the focus by aligning text and/or graphics with pixel
boundaries.
NOTE: Try Auto Image Adjust first.
Sharpness adjusts the clarity and focus of the screen image.
Setup Menu displays the menu shown below:
Language Select allows the user to choose the language used in the menus and
control screens.
15
VG1930wm-1
Control
Explanation
Resolution Notice allows the user to enable or disable this notice.
If you enable the Resolution Notice shown above and your computer is set at a
resolution other than 1440 x 900, the following screen appears.
OSD Position allows the user to move the OSD menus and control screens.
OSD Timeout sets the length of time the OSD screen is displayed. For example,
with a 30 second setting, if a control is not pushed within 30 seconds, the
display screen disappears.
OSD Background allows the user to turn the OSD background On or Off.
Memory Recall returns the adjustments back to factory settings if the display is
operating in a factory Preset Timing Mode listed in the Specifications of this
manual.
16
VG1930wm-1
4. Circuit Description
2. Electronic Circuit Theory
2.1 Switching Mode Power Supply
2.1.1 AC Current Input Circuit
P801 is a connector for connecting AC Power. F801 is a fuse to protect all the circuit. AC input voltage is
from 90v to 264V. R801 and R802 joined between two inputting main circuit to prevent man from shock. L801
is used to clear up low frequency wave. C801 and C802 are used to discharge the waves that L801 produced.
High frequency waves are damped by C801 and C802. D801 is a rectifier which composed of 4 build-in
diodes, it inverts AC to DC.
2.1.2 High Voltage to Low Voltage Control Circuit
C804 is used to smooth the wave from rectifier. IC802 is a highly integrated PWM controller. When
rectified DC high voltage is applied to the HV pin during start-up, the MOSFET Q804 is initially off, and the
Vcc pin capacitor is charged. When the Vcc pin voltage reaches approximately 10V, the control circuitry is
activated and the soft-start begins. The soft-start circuit gradually increases the duty cycle of the MOSFET
from zero to the maximum value over approximately 4ms. If no external feedback/supply current is fed into
the FB pin by the end of the soft-start, the current Setpoint will be above the fault level, FAULT flag is raised, if
the FAULT duration exceeds 80ms, the output controller disable
Resistor R808, R809, R810, R811 are for line over voltage shutdown(OVP)
When PWM is turned off, the main current flow will be consumed through R804 and D802, This will
prevent MOSFET Q804 from being damaged under large current impulse and voltage spike.
D803 and C807 to provide internal Auxiliary voltage to Vcc pin during normal operation. Otherwise, error
amplifier and feedback current input the FB pin for duty cycle control.
2.1.3 DC_5V and DC_14V Output Circuit
For DC 5V, D805 is used to rectify the inducted current. R828 and C814 are used to store energy when current
is reversed. The parts including C818, C822, C820,L803 are used to smooth the current waves.
For DC 14V, D803 is used to rectify the inducted current. R827 and C813 are used to store energy when
current is reversed. The parts including C815, C817 and L802 are used to smooth the current waves.
2.1.4 Feedback and OVP Protect Circuit
Pin R of IC803 is supplied 2.5-v stable voltage. It connects to 5V and 14V output through R822, R823 and
R824. R822, R823 and R824 are output sampling resistor. When the sampling voltage more than 2.5V or less than
2.5V, current of FB IC802 will change, this can change the voltage from T801.
OVP Protect Circuit: When output is overvoltage, the auxiliary winding voltage will be increased, when it
reaches about 14V. Q803 is triggered . It makes the IC802 Pin 1 exceed 5V, then the IC802 output will be disabled.
Q801, R816, R817 and ZD803 make up of dummy loading circuit. For start-up sequence, during 5V output
take place high loading first, this dummy loading circuit operated to insure 14V not be increased.
2. 2 Inverter Circuit
1R503, ZD501, R502, Q501 components convert +14V voltage into +5.0V voltage, and the voltage supply to
IC501. The extra PWM pulse signal (BRIGHTNESS signal)input to control IC through R512, R514, C510, The LCT
pin is set to a DC voltage of 0.7V by using a resistor divider(R507, R516), change the duty of PWM pulse, will
17
VG1930wm-1
regulate the lamp current. The ON/OFF voltage connect to pin10 of IC501 through D501, R501, A voltage of 2V to
pin10 of IC501 enables the IC and activates the striking timer. The SSTCMP pin of IC501 performs the soft function,
the C511 set the time of SST. The operation frequency determined by external capacitor C512, C521 and resistor
R508 connected at CT pin of IC501. C515 connect the TIMER pin of IC501, the capacitor to set striking time and
shunt down delay time. DRV!, DRV2 output for power MOSFET U501, U502.
2.OZ9938 provides two drive signals forU501, U502, and they work in push pull topology driving, two
transformers are connected in parallel with each transformer driving two lamps in series.Turningeach N-Channel
MOSFET on/off complementarily, produces an alternating current through thetransformer primary and
secondary. The on duration of the switches determines the amount of energy delivered to the CCFLs. R504,
C504, R505, C505, R532, C529, R530, C522 are snubber networks, they suppress Voltage transient spike in drain
of power MOSFET.
3. R506, R510, C509, C513, C514, R525, R531, C528, C525, and C527 are connected betweenhigh voltage
output connector and ground, the divided AC voltage is inverted DC voltage through D502, D503, D508, and
D509.The sense voltage feedback to VSEN (pin 6 of IC501) for an over voltage/over current condition during normal
operation. R528, R533 are current sense resistor, current sense signal feed back to Isense (pin 5 of IC501) for lamp
ON detection.
2.2 I/F Board Circuit

2.2.1 Power Input
+5V is from the power board and supply for U101(LD1117AL-3.3V)U105(TSUM56AL-1) and panel. +3.3V
output is generated from +5V through C101 and C103 filtering, and U101 outputs. +3.3V is used for U105
(MCU & Scaler: TSUM16AL). +1.8V output is generated from +3.3V through U102 outputs. +1.8V is only used
for U105.
2.2.2 MCU & Scaler(TSUM56AL-LF-1)

The frequency of XTAL1 is 14.318MHz. U105 # 48 is defined as panel-enable. When the I/O port is high,
Q101 and Q103 are conducted. And then after C108 and C109 filtering, obtain the voltage of VLCD, which will
be connected to CN104. U105 # 85 is defined as CCFL-enable. When the I/O port is low, Q106 is pulled up
and the backlights are on; When the I/O port is high, Q106 is conducted and the backlights are off. U105 # 35
is defined as DET-VGA, connected with CN103 #5. U105 # 84 is a pin of hardware reset. U105 # 54-# 55,#
58-# 65, # 67-# 74, # 77-# 78 output LVDS digital data of 8 bit to panel control circuit through CN104. U105 #
86 generates a PWM waveform by regulating the duty to control the brightness of the backlights.
U103 is EEPROM used for saving EDID data, which is connected by SCL and SDA pins with # 31 and # 30 of
TSUM56AL-LF-1.
U106 is a flash memory, U106 # 2, # 1, # 6, # 5 are the communications with U105 # 37-# 40.
U108 is EEPROM used for saving users OSD setting. U108 is connected by SCL and SDA pin with # 44 and
# 43 of TSUM56AL-LF-1.
2.2.3 VGA Input

Signal R, G, B input through CN103 #1, #2, #3, and C112, C113 and C114 filtering the high frequency noise.
Signal HSYNC and VSYNC input through CN103 #13 and #14, and C125, R137, C126, R136 filtering. Then
18
VG1930wm-1
the analog signal enters U105, and then U104 deals with it internally. In addition, TVS101, TVS102, TVS103,
TVS104 (the four are BAV99), ZD101, ZD105, ZD106, ZD107, ZD108(they are constant voltage diode of 5V6)
are ESD protector. Signal DDC-SCL inputs via CN103 #15, and then passes through ZD101 for ESD
protection, goes into EDID EEPROM IC U103. Signal DDC-SDA inputs via CN103 #12, and then passes
through ZD107 for ESD protection, goes into EDID EEPROM IC U103. CN103 #5 is defined as cable detect
pin, this detector realizes via R124 and U105 # 35,The PC-5V of U103 is supplied by PC via CN103 #9 with
D103 for ESD protection, or supplied by Monitor self via D103.U103 is an EEPROM IC, which is a kind of
memory and used for saving EDID data.
2.2.4 DVI Input

Signal R, G, B input through CN102 #1, #2, #9, #10, #17, #18. Signal HSYNC and VSYNC input through
CN103 #1 and #2. Then the digital signal enters U105, and then U104 deals with it internally. In addition,
TVS105, TVS106, TVS107, TVS108 , TVS109, TVS110, TVS111 (the ten are BAV99),are ESD protector.
Signal DDC-SCL inputs via CN103 #15, and then passes through ZD101 for ESD protection, goes into EDID
EEPROM IC U103. Signal DDC-SDA inputs via CN104 #12, and then passes through ZD107 for ESD
protection, goes into EDID EEPROM IC U104. CN102 #15 is defined as cable detect pin, this detector realizes
via R124 and U105 # 35,The PC-5V of U103 is supplied by PC via CN102 #9 with D102 for ESD protection, or
supplied by Monitor self via D103.U104 is an EEPROM IC, which is a kind of memory and used for saving
EDID data.
2.2.5 Button Control

Button Key-Power is defined as power on/off, which is connected to U105 # 90 through CN105 # 6.
Button Key-2 is defined as two functions of selecting and adjustment, which is connected to U105 #94
through CN105 # 5.
Button Key-Up is defined as plus, which is connected to U105 # 95 through CN105 # 8.
Button Key-Down is defined as minus, which is connected to U105 # 99 through CN105 # 7.
Button Key-1 is defined as two functions of menu and exit, which is connected to U105 # 89 through CN105
# 4.
LED indicator on the front bezel is defined as follows:
a. When press button Key-Power, U105 # 91 is pulled down and U105 # 92 is pulled high, so Q102 is
conducted and the LED indicator is green.
b. When in power-saving mode, U105 # 91 is pulled high and U105 # 92 is pulled down, so Q105 is conducted
and the LED indicator is orange.
3. FACTORY PRESET TIMING TABLE

TIMING
640*350@70Hz
IBM
640*400@70Hz
IBM
720*400@70Hz
FH(KHz)
FV(Hz)
31.469
70.086
31.469
70.086
31.469
70.087
Sync
Polarity
+
Total
(Dot/Line)
800
449
800
449
900
449
Active Sync Width Back Porch

Pixel
(Dot/Line) (Dot/Line)
(Dot/Line) Freq.(MHz)
640
350
640
400
720
400
19
96
2
96
2
108
2
48
60
48
35
54
35
25.175
25.175
28.322
VG1930wm-1
MAC
832*624@75Hz
24.700
50.000
31.469
59.940
35.000
66.667
37.861
72.809
37.500
75.000
43.269
85.008
35.156
56.250
37.879
60.317
48.077
72.188
46.875
75.000
53.674
85.061
49.725
74.550
+
+
+
+
+
+
+
+
+
+
800
494
800
525
864
525
832
520
840
500
832
509
1024
625
1056
628
1040
666
1056
625
1048
631
1152
667
640
480
640
480
640
480
640
480
640
480
640
480
800
600
800
600
800
600
800
600
800
600
832
632
96
2
96
2
64
3
40
3
64
3
56
3
72
2
128
4
120
6
80
3
64
3
64
3
48
8
40
25
96
39
120
20
120
16
80
25
128
22
88
23
64
23
160
21
152
27
224
39
VESA
48.363
1344
1024
136
160
1024*768@60Hz
60.004
806
768
29
VESA
1024*768@70Hz
56.476
70.069
60.023
75.029
68.677
84.997
57.700
72.125
67.500
75.000
68.681
75.062
60.000
60.000
75.000
75.000
63.981
60.020
79.976
75.025
+
+
+
+
+
+
+
+
+
+
+
+
+
+
1328
806
1312
800
1376
808
1360
800
1600
900
1456
915
1800
1000
1800
1000
1688
1066
1688
1066
1024
768
1024
768
1024
768
1024
768
1152
864
1152
870
1280
960
1280
960
1280
1024
1280
1024
136
6
96
3
96
3
136
6
128
3
128
3
112
3
112
3
112
3
144
3
144
29
176
28
208
36
144
26
256
32
144
39
312
36
312
36
248
38
248
38
640*480@50Hz
VESA
640*480@60Hz
640*480@67Hz
VESA
640*480@72Hz
VESA
640*480@75Hz
VESA
640*480@85Hz
VESA
800*600@56Hz
VESA
800*600@60Hz
VESA
800*600@72Hz
VESA
800*600@75Hz
VESA
800*600@85Hz
VESA
1024*768@75Hz
VESA
1024*768@85Hz
1024*768@72Hz
VESA
1152*864@75Hz
MAC
1152*870@75Hz
VESA
1280*960@60Hz
1280*960@75Hz
VESA
1280*1024@60Hz
VESA
1280*1024@75Hz
20
19.760
25.175
30.240
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
65.000
75.000
78.750
94.500
78.472
108.000
100.000
108.000
130.000
108.000
135.000
VG1930wm-1
4. Power On/Off Sequence

4.1 Hardware Power ON
When power cord is plugged into AC socket, SMPS starts work and provides U105 with VCC5V. When
VCC5V inputs, U105 resets circuit active, sets U105 all registers to preset modes, and then monitor goes into
stand-by mode. That means hardware power on has been completed.
4.2 Software Power ON/OFF

When press power key, U105 # 90 recieves low pulse,and then U105 will do the power on/off.
-
If Power ON, U105 # 91(LED_Green) will send out Low potential, and then LED green on.
If Power OFF, U105 # 91(LED_Green) will send out High potential, and then LED Off.
The Panel_Vcc, Backlight_En, CLK/DATA output to panel will follow the following sequency.
T1 (ms)
T2 (ms)
T3 (ms)
T4 (ms)
T5 (ms)
T6 (ms)
T7 (ms)
0.1~10
0.5~10
>200
>100
0~50
0.1~25
>1000
5. AC Outlet Pin Assignment
P801
Pin
Symbol
Description
Live
Neutral
GND
21
VG1930wm-1
6. Inner Connector Pin Assignment

6.1 CN501, CN502, CN503, CN504 (Connect to Panel Backlight, SM02B-BHSS-1-TB or equivalent)
Pin
Symbol
Description
H.V.
High voltage for lamp
L.V.
Low voltage for lamp
6.2 CN101 (Power BD to Interface BD)

Pin No.
Symbol
Description
VCC5V
+5.1V INPUT
VCC5V
+5.1V INPUT
GND
ON/OFF
BRIGHTNESS
GND
Ground
VOL
Volume control input (For VA703m only)
MUTE
GND
CCFL on/off control
Panel luminance control (CCFL brightness)
Mute control input (For VA703m only)
6.3 CN105 (Interface BD to Keypad) DC power on/off control

Pin
Symbol
No.
Description
LED_ GREEN
Orange LED lighting control
LED_ ORANGE
Green LED lighting control
GND
Ground
KEY_POWER
DC power on/off control,
KEY_UP&
OSD control to adjust value to increase,
KEY_DOWN&2
Select control and auto adjustment control,
GND
OSD control to adjust value to decrease
KEY_1
OSD menu and exit
6.4 CN104 (Connect I/F BD to panel, FI-X30S-H or Equivalent)

Pin No.
Symbol
Function
*-
RXO0-
minus signal of odd channel 0(LVDS)
RXO0+
plus signal of odd channel 0(LVDS)
RXO1-
RXO1+
RXO2-
RXO2+
GND
Ground
RXOC-
minus signal of odd clock channel (LVDS)
22
VG1930wm-1
RXOC+
plus signal of odd clock channel (LVDS)
10
RXO3-
11
RXO3+
12
RXE0-
minus signal of even channel 0(LVDS)
13
RXE0+
plus signal of even channel 0(LVDS)
14
GND
Ground
15
RXE1-
16
RXE1+
17
GND
Ground
18
RXE2-
19
RXE2+
20
RXEC-
minus signal of even clock channel (LVDS)
21
RXEC+
plus signal of even clock channel (LVDS)
22
RXE3-
23
RXE3+
24
GND
Ground
25
GND
Ground
26
GND
Ground or Open
27
GND
Ground
28
VCC
Power supply (5.0 V)
29
VCC
30
VCC
6.5 CN103 (D-SUB Connector)

Pin
Symbol
Pin
Symbol
Pin
Symbol
Red video input
Red GND
11
GND
Green video input
Green GND
12
Serial data (SDA)
Blue video input
Blue GND
13
H / H+V SYNC
GND
+5V(from PC)
14
VSYNC
Cable Detect
10
GND
15
Data clock line (SCL)
6.6 CN102 (DVI Connector)

Pin
Symbol
T.M.D.S.Data2-
T.M.D.S.Data1-
17
T.M.D.S.Data0-
T.M.D.S.Data2+
10
T.M.D.S.Data1+
18
T.M.D.S.Data0+
19
T.M.D.S.Data0/5 Shield
T.M.D.S.Data2/4
Shield
Pin
11
Symbol
Pin
T.M.D.S.Data1/3
Shield
Symbol
T.M.D.S.Data4-
12
T.M.D.S.Data3-
20
T.M.D.S.Data5-
T.M.D.S.Data4+
13
T.M.D.S.Data3+
21
T.M.D.S.Data5+
DDC Clock
14
+5V Power
23
22
T.M.D.S.clock Shield
VG1930wm-1
DDC Data
15
Ground(for+5V)
23
T.M.D.S.Clock+
No Connect
16
Hot Plug Ddtect
24
T.M.D.S.Clock-
7. Key Parts Pin Assignment

7.1 IC802 (TOP245Y or TOP246Y, Power Control IC)
Pin
Symbol
I/O
Description
Control
Line Sense
External Current Limit
Source of MOSFET(GND)
Frequency
Drain of MOSFET
7.2 IC501 (OZ9938GN, CCFL inverter controller IC)

Pin No.
Symbol
I/O
Description
DRV1
Drive output
VDDA
Supply voltage input
TIMER
Timing capacitor to set striking time and shut down delay time
DIM
ISEN
Current sense feedback
VSEN
Voltage sense feedback
OVPT
Over-voltage/over-current protection threshold setting pin
NC
ON/OFF control of IC
Analog dimming or Internal LPWM dimming or external PWM

pulse input for dimming function
NC
10
ENC
11
LCT
12
SSTCMP
Capacitor for soft start time and loop compensation
13
CT
Timing resistor and capacitor for operation and striking frequency
14
GNDA
15
DRV2
16
PGND
Timing capacitor to set internal PWM dimming frequency and

also a pin for analog dimming selection
Ground for analog signals

O
Drive output
Ground for power paths
7.3 U105(TSUM56AL-LF-1)
Pin
Symbol
I/O
Description
NC
Not connected
GND
Ground
NC
Not connected
NC
Not connected
24
VG1930wm-1
GND
Ground
NC
Not connected
NC
Not connected
AVDD_DC
NC
Not connected
10
NC
Not connected
11
GND
Ground
12
NC
Not connected
13
NC
Not connected
14
AVDD_DC
15
REXT
16
AVDD_PLL
PLL Power
17
BIN0M
Reference ground for analog blue input
18
BIN0P
Analog blue input
19
GIN0M
Reference ground for analog green input
20
GIN0P
Analog green input
21
SOGIN0
Sync-on-green input
22
RIN0M
Reference ground for analog red input
23
RIN0P
Analog red input
24
AVDD_ADC
ADC Power
25
REFM
Internal ADC bottom de-coupling pin
26
REFP
Internal ADC top de-coupling pin
27
HSYNC0
Analog HSYNC input
28
VSYNC0
Analog VSYNC input
29
GND
30
DDCA_SDA/RS232_TX
I/O
31
DDCA_SCL/RS232_RX
I/O
32
33
34
VDDP
GND
VDDC
35
GPIO_P15/PWM0
36
37
38
39
40
41
42
NC
SDO
SCZ
SCK
SDI
NC
NC
43
GPIO_P11/I2C_MDA
I/O
44
GPIO_P10/I2C_MCL
I/O
45
46
47
NC
NC
NC
ADC Power
ADC Power
External resistor 390 ohm to AVDD_ADC
I
I
I/O
I
O
O
O
Ground
DDC Data for Analog Interface; 4mA driving strength/UART
Transmitter/GPIO
DDC Clock for Analog Interface/UART Receiver/GPIO
Digital Output Power
Ground
Digital Core Power
General Purpose Input/Output; 4mA driving strength/Pulse Width
Modulation Output; 4mA driving strength
Not Connected
SPI Flash Serial Data Output
SPI Flash Chip Select
SPI Flash Serial Clock
SPI Flash Serial Data Input
Not Connected
Not Connected
General Purpose Input/Output; 4mA driving strength/I2C Master
Data
General Purpose Input/Output; 4mA driving strength/I2C Master
Clock
Not Connected
Not connected
Not connected
25
VG1930wm-1
GPIO_P27/PWM1
49
VDDP
50
GND
51
VDDC
Digital Core Power
52
MODE[0]
Chip Configuration Input
53
MODE[1]
Chip Configuration Input
54
LVA3P
A-Link Positive LVDS Differential Data Output
55
LVA3M
A-Link Negative LVDS Differential Data Output
56
VDDP
57
GND
58
LVACKP
A-Link Positive LVDS Differential Clock Output
59
LVACKM
A-Link Negative LVDS Differential Clock Output
60
LVA2P
61
LVA2M
62
LVA1P
63
LVA1M
64
LVA0P
65
LVA0M
66
VDDC
Digital Core Power
67
LVB3P
B-Link Positive LVDS Differential Data Output
68
LVB3M
B-Link Negative LVDS Differential Data Output
69
LVBCKP
B-Link Positive LVDS Differential Clock Output
70
LVBCKM
B-Link Negative LVDS Differential Clock Output
71
LVB2P
72
LVB2M
73
LVB1P
74
LVB1M
75
VDDP
76
GND
77
LVB0P
78
LVB0M
79
GND
Ground
80
BYPASS
For External Bypass Capacitor
81
NC
Not connected
82
VDDC
83
GND
84
RST
85
GPIO_P12
I/O
General Purpose Input/Output; 4mA driving strength/Pulse Width

Modulation Output; 4mA driving strength
48

Ground
Ground
Ground
Digital Core Power

Ground
I
I/O
Chip Reset; High Reset

General Purpose Input/Output; 4mA driving strength
26
VG1930wm-1
PWM1/GPIO_P25
87
RSTN
88
GPIO_P00/SAR1
I/O
89
GPIO_P01/SAR2
I/O
90
GPIO_P02/SAR3
I/O
91
GPIO_P06
I/O
92
GPIO_P07
I/O
93
PWM0/GPIO_P26
I/O
Pulse Width Modulation Output; 4mA driving strength/General

Purpose Input/Output; 4mA driving strength
94
GPIO_P13
I/O
95
GPIO_P14
I/O
96
XIN
Crystal Oscillator Input
97
XOUT
Crystal Oscillator Output
98
AVDD_MPLL
MPLL Power
99
GPIO_P16/PWM2
100
NC
I/O
Pulse Width Modulation Output; 4mA driving strength/General
86
I/O
Purpose Input/Output; 4mA driving strength

Chip Reset; Low Reset
General Purpose Input/Output; 4mA driving strength/SAR ADC
Input
Input
Input
General Purpose Input/Output; 6/12mA programmable driving
strength
General Purpose Input/Output; 6/12mA programmable driving
strength
General Purpose Input/Output; 4mA driving strength/

Pulse Width Modulation Output; 4mA driving strength
Not connected
27
VG1930wm-1
5. Adjustment Procedure
1.
Key Function Description

CONTROL KEY
[AUTO] [2]
By pressing [AUTO] key, Auto Image Adjust is performed
[MENU] [1]
By pressing [MENU] key, Main menu display

A. When MENU OSD display, press these keys to change the contents of an
adjustment item, or change an adjustment value
B. When MENU OSD is un-display, press these keys to change brightness and
contrast
Power on or power off the monitor
[] []
[POWER]
2.
KEYS FUNCTION
Hot Key Operation

Hot Key Function
Item
Function Detail
Recall Contrast or Brightness while in the Contrast or Brightness adjustment;
[] + []
Recall both Contrast and Brightness when the OSD is not open
[1] +[2]
Toggle 720x400 and 640x400 mode when input 720x400 or 640x400 mode
[1] + [] + []
(keep pushing 5 sec)
White Balance (Not shown on users guide)
[1] + []
Power Lock
[1] + []
OSD Lock
[] + []+ [ ]
Enter Factory Mode
Remark: All the function above are only available while OSD off
3.
OSD Control
3.1 OSD table
Layer 1
Layer 2
Layer 3
Auto Image Adjust

Contrast/Brightness
Audio
Color Adjust
Contrast (+ / -)
*3,4
Brightness (+ / -)
*3,4
Volume
Volume (+ / -)
Mute
On/Off
sRGB
9300K
7500K
6500K
5400K
User Color
Red (+ / -)
Green (+ / -)
28
VA1930wm-1
Blue (+ / -)
Information
H Position (+ / -)
H/V Position
Manual Image Adjust
V Position (+ / -)
H Size
+/-
Fine Tune
+/-
Sharpness
+/English
French
German
Italian
Language Select
Spanish
Finnish
Japanese
Setup Menu
Simplified Chinese
Traditional Chinese
Resolution Notice
On/Off
OSD Position
H Position (+ / -)
*3
V Position (+ / -)
*3
OSD Time Out

OSD Background
On/Off
Memory Recall
3.2 OSD lock Menu function
OSD Lock Menu Function Check

Item
Method
Activate OSD lock
[1] + [] 10S
Deactivate OSD lock:
[1] + [] 10S(again)
Phenomenon
Press any of buttons"1", "",
"", "2" will appear "OSD Locked" 3s
NOTICE:
When the OSD is locked will lock all functions.
Status bar indicating OSD Lock or Unlock is in progress and when complete it will indicate OSD Locked
OSD Lock should not lock Power Button and Power Lock function
3.3 Power lock Menu function

Power Lock Menu Function Check
Item
Method
Phenomenon
29
VA1930wm-1
Can not turn off the LCD;

Press the power button will appear "Power Button
Activate Power Lock
Locked" OSD 3s;
[1] + [] 10S
LCD would automatically turn back "On" when

power is restored after a power failure
Deactivate Power Lock
[1] + [] 10S(again)
NOTICE:
Status bar indicating Power Button lock or unlock is in progress and when complete it will indicate Power Button
Locked
Power should only be lockable in the On State
3.4 Resolution notice function

Resolution Notice Menu
Item
Method
Phenomenon
Resolution Notice OSD should show on screen

Activate
Resolution
after changing to non-native mode for 30 sec,

And it should disappear after 10s
Notice Menu
------
or by pushing button [1] or [2]

Deactivate
Push button [2] under Resolution Notice OSD,
Resolution Notice Menu
select Disable
-------
3.5 Factory Mode Introduction

When input the signal, press power key to turn off the monitor. Press [] +[] +[ ] at the same time so
as to enter factory mode. After power on, press Menu[1] key, you can see the Factory menu.
INL-V0
: Currently using panel model name
V4 060922
: Currently using firmware version information.
Auto Color
: Automatically calibrate chip ADC parameter by using chip internal DAC
Color Temperature : The R, G, B of 9300K and 6500K and 5400K and User Mode
Colors are all generated from scaling back end.
4. Burn-in pattern
If it is a new monitor, and in factory mode, if no VGA signal input, Burn-in pattern will self generate automatically.
Burn in patterns are: full Red, Green, Blue, White and Black. You can not escape from Burn-in pattern until plug in
VGA Cable, and then press the power key. Turn the monitor off and then turn it on.

30
VA1930wm-1
5. Auto Color (Automatically calibrate chip ADC parameter by using chip internal DAC)
If it is a new-built set and it is first time to do the auto color, please confirm the following steps:
-Connect the VGA cable with the standard video pattern generator and display 16-gray pattern on the monitor.
- Press Power to power off the monitor.
- Press [] +[] +[ ] simultaneously to enter factory mode.
- Press Menu[1], then press Auto[2] to execute Auto color item.
- After the Auto Color process finished, please press Power to restart monitor.
6. EDID (Rewrite EDID data to EEPROM)

If we need to rewrite the EEPROM data, please confirm the following steps.
1. Plug in VGA Cable; we can rewrite the EDID data to EEPROM by using EDID Rewrite program.
2. If the EDID Rewrite process finished, please pull out VGA cable and press 2+ at the same time.
3. Pull out AC power cable or press power key to restart.
7. Upload firmware to MCU via VGA Cable

7.1 Connect ISP board between monitor and PC as below configure
Service
cable
ISP Board
D-Sub
D-SUB
Port 25pin
Print Port
Insert to Print
LCD Monitor
7.2 Using mStar ISP Tool Update FW:

(1). Seletct Read, Choose the corresponding firmware, load to MCU.

31
VA1930wm-1
(2). Select Connect, auto connect for ISP.
(3). Select Run, start ISP.
(4). When the picture show Verify OK, ISP finished.

32
VA1930wm-1
After repair, to ensure the quality you should do the following test and adjustment
Item
Test OSD function
Content
Equipment
1.Signal is set as 1280x1024@60Hz

2. LCM button are from left to right, checking whether each single
function key and compound function key can be worked.
Contrast Check
1. Set input mode to 1280x1024@60Hz

2. Set Pattern to 32 gray shades
3. Set contrast to the max. The brightest 6~8 shades brightness cannot
Chroma
Signal Generator
Chroma
Signal Generator
be distinguished.
Color Temperature
Modes switching
check
Y measurement at
default setting
Panel Flicker
check
1. Do Auto color at 640 x 480@60Hz, 5-Mosic pattern

2. Measure color temperature, check it complies with the following
temperature:
5400K x=0.335 +/- 0.02, y=0.350 +/- 0.02
6500K x=0.313 +/- 0.02, y=0.329 +/- 0.02
7500K x=0.299 +/- 0.02, y=0.315 +/- 0.02
9300K x=0.283 +/- 0.02, y=0.298 +/- 0.02
Chroma Signal
Generator and color
analyzer
1. Use Chroma Pattern Generator to make sequence.

VESA (640x480 800x600 1024x768 1280x1024), MAC 832x624
DOS (640x350 720x400), the detail supported modes and power
saving signal.
2. Confirm the above timing modes must be full screen and the
picture must be normal.
3. LED is Orange at power saving mode.
Chroma Signal
Generator
1. Set brightness to default value 100 and contrast to default value

70 at 6500K
2. At full white patter, Measure Y, which should be 250cd/m
Chroma Signal
Generator and Color
Analyzer
1. Mode: 1440x900@60Hz
2. Set Brightness& contrast to default value
3. Do Auto Image Adjust
4. Shut down PC to check whether theres glitter on the center of the
Equipment::
Chroma Signal
Generator & PC
picture.
Power saving
1.
2.
3.
4.
5.
Mode: 1440x900@60Hz
Pattern: full white
Brightness: Max.
Contrast: Default
Check power consumption at each modes
State
Power Consumption
LED color
Normal
Green
42W
Stand By
< 2W
Orange
1
Power Key Off
No

33
Chroma signal
generator and Power
meter
AC input: 230V/50Hz
VA1930wm-1
Packing For Shipping

1.
Packing Procedure
1.1
Paste protection film to protect the monitor. (Figure 1)
1.2
Put the monitor in the PE bag and seal the bag with tape. (Figure 2)
Figure 1
Figure 2
1.3
Put the cushions on the monitor.
1.4
Place the monitor into the carton and then put all the accessories into the carton. At last, close the
carton and seal it with tape. (Figure 3)
Monitor Head
VGA cable
Power cord
Audio cable
Figure 3

34
VA1930wm-1
Disassembly Procedure
Adjust Stand

35
VA1930wm-1

36
VA1930wm-1

37
VA1930wm-1
Power Board
Speaker
I/F Board
Chassis
LVDS Cable
P-Led Cable
Function Key
Bezel
OSD Board
Hold

38
VA1930wm-1
6. Troubleshooting Flow Chart

1. Common Acknowledge
z
If you change the interface board, be sure that the U103, U105, U106 and U108 these three components also
changed to the new I/F board because there was program inside. If not, please re-write EDID and upload
firmware into U106 via VGA Cable.
If you adjust clock and phase, please do it at the condition of Windows shut down pattern.
If you confirm the R.G.B. color is normal or not, please do it under 16-grey scalar pattern.
This LCM is analog interface. So if the entire screen is an abnormal color that means the problem happen in
the analog circuit part, if only some scale appears abnormal color that stand the problem happen in the digital
circuit part.
If you check the H/V position, please use the crosshatch pattern.
This LCM support more than 30 timing modes, if the input timing mode is out of specification, the picture may
appears abnormally.
If brightness uneven, repairs Inverter circuit or change a new panel.
If you find the vertical line or horizontal line lost on the screen, please change panel.
If you find the speaker dont working, please dont plug in audio cable, unless change new speaker.

39
VA1930wm-1
2. No Power & Power LED Off

No power
Check primary
Check circuit
Check IC802,
rectifier voltage
if short
C804, T801,
Check F801, P801,

RT,801,D801
Check pin6 of IC802

CheckC810,D803,C807,
voltage about 12V
Check pin2 of IC802
Check primary OVP, OLP
voltage about 2V
and secondary feedback,
Check pin1 of IC802
Check R811, R810,
voltage is below 1V
R809, R808,R814
END
40
VA1930wm-1
3. DC output voltage is unstable

Unstable power
Check sampling
Circuit
Check R822,
R823, R824
Change R822,
R823, R824
Check the C
pin voltage of
IC803 if 3V
Check the R pin

voltage of IC803
about 2.5V
Change
IC803
Check R819, R820
Check pin2 of
IC802 voltage
is 3V
Check R818, D804,

C807 if short
Change
R818, D804,
Check pin1 of
IC802 voltage
below 1V
Change R808, R 809,

R810, R 811, R815,
END

41
VA1930wm-1
4. Output power is unstable

Unstable power
Check sampling
Check R810,
Circuit
R811, R818
Change R810, R811,

R818
Check the R pin
Check the C pin
voltage of IC803
voltage of IC803
Change
about 2.5V
if 3V
IC803
Check R809, R808, R814,

D809
Check pin1 of
Check D806, C815 if
IC802 voltage
short
is 5.8V
Change
D806, C815
Check pin3 of
Change R801, R805,
IC802 voltage
R822, R823, R817
about 1V
END

42
VA1930wm-1
5. Backlight cant be turned on

Black screen
NG
Check power
supply:pin 1,2 of
CN101
Power fail
YES
NG
Check FB102,FB103,
FB105,FB106
Check power supply

for U105
YES
NG
Check reset (pin84) of

U105
Check C144,R172
YES
NG
Check crystal (pin 96,97)
waveform of U105
Check
X101,C153,C154
YES
Check CCFLEnable(pin 85)

of U105
NG
YES
YES
Check pin4 of
CN101
Inverter Fail
NG
Check R167,Q106,
R108,R110
U105 FAIL

43
VA1930wm-1
6. Black Screeqn and backlight turn on

44
VA1930wm-1
7. White Screen
White screen
OK
LVDS Cable
Reinsert
Workmanship
NG
OK
Change
LVDSCable
LVDS cable NG
NG
OK
OK
Check VLCD
is 5V
Check LVDS
signal
NG
Panel Fail
NG
Check Panel-Enable of
U105(pin48)
OK
U105 Fail
NG
Check
Q101,Q103,Q110,
C108,
C109
END

45
VA1930wm-1
8. Bad Screen
Bad Screen
OK
LVDS Cable
Reinsert
Workmanship
NG
OK
Change LVDS
Cable
LVDS Cable NG
NG
NG
Check Crystal:
pin96,97 of U105
CheckX101, C153,
C154
OK
Check the pins of
U105

46
VA1930wm-1
7. Recommended Spare Parts List

RECOMMENDED SPARE PARTS LIST (VG1930wm-1)
ViewSonic Model Number: VS11354
Serial No. Prefix: QC4
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Accessories:
PC Board
Assembly:
Cabinets:
Cables:
Electronic
Components:
Packing Material:
Plastics:
Description
Power Cord 10A/250V 6FT (Australia)
Power Cord 16A/250V 6FT (Europe)
Power Cord 5A/250V (Singapore)
Power Cord, 10A/250V BLK 6FT (China)
Power Cord 10A/125V BLK 6FT UL/CSA USA RoHS
Power Cord 7A/125V 6FT (Taiwan)
Power Cord 16A/250V 6FT (Korea)
Kit Accessory - INL-V0
Sub Board
Key Board
Led Board
Interface Board
Back Cover
Cover - Hinge (B)
Front Panel (Bazel)
Audio Cable (1P 6FT)
D-Sub Cable (Black)
Wire (HRN Assy) #28,RoHS
Wire (HRN Assy),270mm#28,RoHS
Flat Cable FFC 30P 160mm,RoHS
Speaker W/Case 1.5W 16 350mm
LCD PANEL 19" MT190AW01-V0,AM19000040
Foam - Right
Foam - Left
PE Bag - L620xW510xT0.6mm
Craft Box
Bag, Plastic W(575+300)xL1125xT0.05mm
Generic Foam Set
Generic Box
Pedestal (Stand)
Rev: 1a
ECR/ECN
ViewSonic P/N
A-00003671
A-00003674
A-00003675
A-00005255
A-00006679
A-00006733
A-00006734
A-00008064
B-00008023
B-00008024
B-00008025
B-00008165
C-00008180
C-00008182
C-00008183
CB-00008002
CB-00008009
CB-00008010
CB-00008011
CB-00008013
E-00008012
E-00008016
P-00008167
P-00008168
P-00008170
P-00008171
P-00008172
P-00001347
P-00002515
PL-00008045
Ref. P/N
453070800420R
453070800210R
453070800230R
453070800170R
453070800250R
453070800480R
453070800500R
703000003110R
790691401600R
790691501000R
790682201000R
790691302600R
714050007400R
501020209600R
714030007400R
453030300120R
453010100150R
430300400110R
430300800710R
430303000600R
618100101500R
631102090600R
506040009710R
506040009700R
506120301700R
506020012300R
506120006300R
30833
20653
714010008600R
Location
Universal number#
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic
Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
47
VG1930wm-1
BOM LIST (VG1930wm-1)

Rev: 1a
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
ViewSonic P/N
P-00008167
P-00008168
N/A
N/A
CB-00008002
A-00006679
CB-00008009
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
P-00008171
P-00008170
N/A
N/A
A-00008064
N/A
N/A
N/A
C-00008182
N/A
N/A
N/A
E-00008012
N/A
C-00008180
N/A
N/A
C-00008183
N/A
N/A
N/A
N/A
N/A
PL-00008045
N/A
N/A
HW-00005269
HW-00005270
N/A
B-00008165
B-00008023
B-00008025
B-00008024
E-00008016
N/A
N/A
CB-00008010
CB-00008013
CB-00008011
N/A
N/A
N/A
Ref. P/N
506040009710R
506040009700R
506039000100R
506037005900R
453030300120R
453070800250R
453010100150R
506431000300R
506431003100R
506440002300R
506440002400R
506250012200R
506390000600R
506390500100R
506390210400R
506440002600R
506391000030R
506520700100R
506020012300R
506120301700R
506150007200R
506039003600R
703000003110R
714078061101R
501030204400R
501060200500R
501020209600R
509116608100R
509112306100R
503040000310R
618100101500R
509112306100R
714050007400R
506430300003R
501020209400R
714030007400R
501010207700R
501030204300R
506102000400R
506102000300R
501120104400R
714010008600R
714088061100R
502090304100R
509146305300R
509000000700R
506380001200R
790691302600R
790691401600R
790682201000R
790691501000R
631102090600R
631102090610R
631102090720R
430300400110R
430303000600R
430300800710R
505040503400R
509146304100R
505040204000R
Description
CUSHION,EPS-R, LE1945
CUSHION,EPS-L, LE1945
CORNER PAPER,1000x50x50xT5mm
CARDBOARD,COVER,L1160xW1150xH120mm,LE194
CABLE,AUDIO 1P 6FT BLACK/GREEN CP03B06P0
PWR CORD 10A/125V BLK 6FT UL/CSA,SVT 18x
CABLE,D-SUB 15P MALE 6FT BLACK,SZ4120955
FILM,PE 500mmx900M ROHS
FILM,PROTECTION,UNPRINTED,430x280x0.1mm,
LABEL,BLANK,76.2x76.2mm,LE1709(UPC)
LABEL,BLANK,50x25mm,LE1709(S/N)
LABEL,AGENCY,LE1945(VA1930wm)
LABEL,HI-POT PASS, LE1709
LABEL,ENERGY STAR, LE1709
LABEL,CARTON(5ms),L89xW58 LE1941
LABEL,BLANK,210x65mm,LE1709(PALLET)
LABEL,POP,FOR BEZEL, LE1945
FLYER,LCDTV,LE1945(VA1930wm)
CARTON,VIEWSONIC(VG1930wm), LE1945
BAG,EPE+PE,L620xW510xT0.6mm, LE1925
PALLET,L1140xW1130xH120mm,LE1945
CORNER PAPER,1980x50x50xT5mm, LP1701
KIT,ACCESSORY,LE1945(VA1930wm)
ASSY,FINAL(B,V0/G1&2&3),W/SPK,US,LE1945BUTTON,FUNCTION KEY, LE1941
HOLDER,KEY PAD, LE1941
COVER,HINGE(B), LE1945
SCREW,P,CROSS,M4*8,Zn,ROHS
SCREW,P,CROSS,T.T-3*6,ZnROHS
RUBBER,COVER(B), LE1534
SPEAKER 1.5W 16 350mm,R/B,W/CASE,X3516
SCREW,P,CROSS,T.T-3*6,ZnROHS
ASSY,BACK COVER, LE1945
FILM,PET,L115xW30xT0.05mm, LE1741
COVER,BACK(B),W/DVI, LE1941
ASSY,BEZEL, LE1945
BEZEL,FRONT,LE1945
BUTTON,POWER KEY, LE1941
LOGO PLATE,VIEWSONIC, LE1709(THREE BIRDS
LOGO PLATE,VIEWSONIC, LE1709
LENS, LE1941
ASSY,STAND LE1945
ASSY,PANEL(V0/G1&2),W/SPK,LE1945-642
CHASSIS,W/DVI, LE1941
SCREW,PW,CROSS,W/WAS,M3*5,NI
BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RO
TAPE,MYLAR,66000x20xT0.05
PCBA,I/F BOARD, LE1945-642
PCBA,P/I BOARD, LE1941-642
PCBA,LED BOARD, LE1941
PCBA,KEYPAD BOARD, LE1941
LCD PANEL 19" MT190AW01-V0-G1,AM19000040
HRN ASS'Y 4P 240mm UL1571#28,RoHS
HRN LVDS FFC 30P 160mm,RoHS
HRN ASS'Y 4Px2 to 8P,270mm UL1571#28,RoH
INSULATOR,PP,10x15x10X0.3mm,GLUE(3M), LE
SCREW,P,CROSS W/WAS,M3*4,Zn ROHS
INSULATOR,MYLAR,L370xW6xT0.3mm,LE1909
48
Location
Universal number#
Q'ty
100
100
5.556
2.778
100
100
100
0.25
100
100
100
100
100
100
100
6.25
100
100
100
100
1.389
5.556
100
100
100
100
100
400
500
400
100
500
100
100
100
100
100
100
100
100
100
100
100
100
600
400
0.12
100
100
100
100
100
0
0
100
100
100
400
400
250
VG1930wm-1
8. Exploded Diagram and Exploded Parts List
49
VG1930wm-1
EXPLODED PARTS LIST (VG1930wm-1)

Rev: 1a
Item
1
1-1
1-2
1-3
2
3
4
5
5-1
5-2
5-3
5-4
5-5
5-6
5-7
5-8
6
7
8
9
10
11
12
ViewSonic P/N
C-00008183
N/A
N/A
N/A
N/A
N/A
N/A
N/A
E-00008016
E-00008012
N/A
B-00008024
B-00008023
N/A
B-00008165
HW-00005269
N/A
N/A
N/A
PL-00008045
N/A
C-00008182
B-00008025
Ref. P/N
714030007400R
501010207700R
501030204300R
501120104400R
501060200500R
501030204400R
509112306100R
714088061100R
631102090600R
618100101500R
509146304100R
790691501000R
790691401600R
502090304100R
790691302600R
509146305300R
501020209400R
503040000310R
509142306500R
714010008600R
509116608100R
501020209600R
790682201000R
Description
ASSY,BEZEL,LE1945
BEZEL, Front,LE1945
Button,Power key,LE1941
LENS, LE1941
holder,Keypad,LE1941
button,function key,LE1941
SCREW,P,CROSS T.T-3*6,Zn,ROHS
ASSY,Panel,W/SPK LE1945
Panel INNOLUX
Speaker 1.5W
SCREW,P,CROSS W/WAS,M3*4,Zn ROHS
PCBA,KEY PAD BOARD,LE1941
PCBA,P/I Board,LE1941
CHASSIS,W/DVI, LE1941
PCBA,I/F Board,LE1945
SCREW,PW,CROSS,W/WAS,M3*5,NI
COVER,BACK(B),W/DVI, LE1941
Rubber,COVER(B)
SCREW,P,CROSS W/WAS,T.T3*6,BLK ROHS
ASSY,STAND LE1945
SCREW,P,CROSS,M4*8,Zn,ROHS
Cover,hinge,LE1945
PCBA,LED BOARD, LE1941
50
Q'ty
1
1
1
1
1
1
3
1
1
1
4
1
1
1
1
6
1
1
2
1
4
1
1
VG1930wm-1
PACKING PART LIST ( VG1930wm-1 )

Rev: 1a
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ViewSonic P/N
N/A
N/A
N/A
P-00008167
CB-00008002
CB-00008009
A-00008064
A-00006679
P-00008168
P-00008170
P-00008171
N/A
N/A
N/A
Ref. P/N
506431000300R
506039003600R
506039000100R
506040009710R
453030300120R
453010100150R
703000003110R
453070800250R
506040009700R
506120301700R
506020012300R
506440002300R
506038005000R
506150007210R
Description
FILM,PE 500mmx900M ROHS
CORNER PAPER,1980x50x50xT5mm
CORNER PAPER,1000x50x50mmxT5mm
CUSHION,EPS-R, LE1945
CABLE,AUDIO 1P 6FT BLACK/GREEN CP03B06P0
CABLE,D-SUB 15P MALE 6FT BLACK,SZ4120955
KIT,ACCESSORY,LE1945(VG1930wm)
PWR CORD 10A/125V BLK 6FT UL/CSA,SVT 18x
CUSHION,EPS-L, LE1945
BAG,EPE+PE,L620xW510xT0.6mm, LE1925
CARTON,VIEWSONIC, LE1945
CARTON Label, LE1941
CARDBOARD,L1150xW580xT4mm LE1945
PALLET,L1140xW565xH120mm,LE1945
51
Q'ty
1/32
0.125
0.125
1
1
1
1
1
1
1
1
1
2/32
1/32
VG1930wm-1
9. Block Diagram
52
VG1930wm-1
ADJ
VOUT
+
C104
0.1/50V
C102
C103
0.1/50V
C101
VCC3.3
U102
FS8860-18PJ
VIN
VOUT
VCC1.8
2
1
2
3
4
5
6
7
8
VCC5V
VCC5V
R108
4K7
ON/OFF
SBRI
ON/OFF
R110
4K7
VOL_C
MUTE_C
CCFL_ENABLE
1
Q106
PMBT3904
22u/25V
+
C106
0.1/50V
C105
1
VCC5V
CN101
4500-06
VCC1.8
ADJ
VCC3.3
VLCD
VLCD 4
R107
390
R163
1
3 Q105
PMBT3906
1K
R191
4K7
R106
10K
LED_G_C
VCC3.3
C109
0.1/50V
C111
10u/25V
C108
2
Q103
PMBT3904
LED_G//LED_O
+
3
20K
220u/16V
3 R197
1
R102
Q110
2N7002
1
PANEL_ENABLE
R105
4K7
Q101
AP2305GN
100K
0.1/50V
R190
3
51
C107
From Power &

Inverter
VIN
VCC3.3
VCC3.3
U101
FS8860-33PJ
100u/16V
D101
SKS20-04AT
100u/16V
VCC5V
LED_A//LED_B
R101
390
R162
1
3 Q102
PMBT3906
1K
LED_A_C
CN105
LED_A//LED_B
LED_G//LED_O
1
2
3
4
5
6
7
8
2x4P 2.0mm
From keypad
POWER
MENU_UP//Key_Mute&
DOWN_EXIT//Key_&2
KEY_1
C161
C162
1000p/50V 1000p/50V
Model
Title
Date
53
VG1930wm-1
DC to DC
Rev:
DVI-D_CON
1K
R125
FB101
DDCA_SCL_I 3
R127
100
R129
100
R130
100
R131
100
DDCA_SDA_I 3
R132
100
DDCA_SDA
NC
NC
33p/50V
220p/50V
C123
C124
C125
C126
DDCA_SCL
NC
NC
C121
100
C122
75 1%
R135
2K2
2K2
NC
C120
R136
R137
75 1%
R134
ZD108
5V6
NC
ZD107
5V6
C119
ZD106
5V6
75 1%
ZD105
5V6
R133
ZD101
5V6
120
DET_VGA 3
VSYNC
HSYNC
9
10
11
12
13
14
15
16
DAT1DAT1+
RX0RX0+
GND
RX5RX5+
GND
RXC+
RXC-
17
18
19
20
21
22
23
24
DAT0DAT0+
SCL_DVI
SDA_DVI
3
3
VCC3.3
R123
4K7
DVI5V
R126
R128
DET_DVI 3
100
4K7
R124
4K7
RX1RX1+
GND
RX3RX3+
5V
GND
HP
SCL_DVI_I
SDA_DVI_I
Q104
1R103
4K7/NC
HP_CTRL
PMBT3904/NC
DCLK+
DCLK-
R122
VCC3.3
100
100
100
100
R192
R193
R152
R153
C127 0.1/50V
DETECT
1
2
3
4
5
6
7
8
5V6
60
RIN
3
GNDR
3
GIN
3
GNDG
3
BIN
3
GNDB
3
SOG
3
PC5V_VGA 3
DAT2DAT2+
RX2RX2+
GND
RX4RX4+
SCL
SDA
VS
ZD104
FB113
0.047/25V
0.047/25V
0.047/25V
0.047/25V
0.047/25V
0.047/25V
0.047/25V/NC
5V6
16
15
60
100 C112
100 C113
100 C114
100 C115
100 C116
100 C117
470/NCC118
ZD103
14
FB112
R113
R114
R116
R117
R119
R120
R121
5V6
13
60
ZD102
12
FB111
17
11
CN103
DZ11AA1-H5W6-4F
R
1
6
G
2
7
B
3
8
4
9
5
10
VCC3.3
VCC3.3
3
B+
BG+
GR+
RCLK+
CLK-
3
3
3
3
3
3
3
3
TVS102
BAV99
TVS103
BAV99
TVS104
BAV99
1
1
1
G
B
DETECT
3
TVS112
BAV99
3
TVS111
BAV99
2
3
TVS110
BAV99
3
TVS109
BAV99
3
TVS108
BAV99
2
3
TVS107
BAV99
3
TVS106
BAV99
TVS105
BAV99
VCC3.3
TVS101
BAV99
10
10
10
10
10
10
10
10
R138
R139
R140
R141
R142
R143
R144
R145
DAT0+
DAT0DAT1+
DAT1DAT2+
DAT2DCLK+
DCLK-
D103
VCC3.3
D102 BAV70
4K7
4K7
3
0.1/50V
DVI5V
8
7
6
5
R151
100
SCL_DVI
SDA_DVI
WP
A0
A1
A2
GND
VCC
WP
SCL
SDA
8
7
6
5
CAT24WC02W
CAT24WC02W
R149
R150
VCC
WP
SCL
SDA
1
2
3
4
PC5V_VGA
VCC3.3
BAV70
U103
R146
R147
R148
C128
0.1/50V
U104
1 A0
2 A1
3 A2
4 GND
C129
4K7
4K7
4K7
DDCA_SCL
DDCA_SDA
Model
Title
Date
54
VG1930wm-1
INPUT
Rev:
R173
R174
R172
10K
0.1/50V
C151 0.1/50V
C143 0.1/50V
22u/25V
C142
0.1/50V
0.1/50V
8
7
6
5
8
7
6
5
C139
22u/25V
0.1/50V
0.1/50V
C132
C137
C136
VDVI
C131
C140
1u/16V
FB106
60
VDDP
0.1/50V
VCC3.3
C150
R171
CN104
FFC-CON
0.1/50V
R170
VLCD
C149
26
REFP
REFM
25
NC
NC
NC
X101
14.31818MHz
C138
61
60
59
58
55
54
FB103
60
VPLL
VDDC
0.1/50V
LVA2M
LVA2P
LVACKM
LVACKP
LVA3M
LVA3P
VCC1.8
C135
LVA1M
LVA1P
63
62
FB105
60
MUTE_C
VOL_C
SBRI
CCFL_ENABLE
PANEL_ENABLE
HDCP_WP
0.1/50V
70
69
68
67
65
64
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
1K
1K
1K
4.7K
100
100
VMPLL
C148
LVBCKM
LVBCKP
LVB3M
LVB3P
LVA0M
LVA0P
R164
R165
R166
R167
R168
R181
VCC3.3
0.1/50V
78
77
74
73
72
71
I2C_MCL
I2C_MDA
LED_G_C
LED_A_C
C134
LVB0M
LVB0P
LVB1M
LVB1P
LVB2M
LVB2P
HP_CTRL
Key_1
POWER
MENU_UP//Key_mute&
DOWN_EXIT//Key_&2
0.1/50V
94
93
86
85
48
47
1K
1K
1K
1K
1K
R157
R158
R159
R160
R161
C147
GPIO_P13
PWM0/GPIO_P26
PWM1/GPIO_P25
GPIO_P12
GPIO_P27/PWM1
PWM2/GPIO_P24
1
2
3
4
22u/25V
42
41
44
43
36
45
46
XOUT
97
MODE[0]
MODE[1]
RST
4K7 52
4K7 53
84
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
10u/25V
2
5
11
29
33
50
57
76
79
83
C144
VCC5V
C154 22p/50V
VCTRL
VCC5V
XIN
81
C153 22p/50V 96
REXT
BYPASS
15
80
SST25VF010A
R169
390 1%
SDO
SCZ
SCK
SDI
0.1/50V
SO
CS#
SCK
SI
FB104
60
R180
GPIO_P22
GPIO_P23
GPIO_P10/I2C_MCL
GPIO_P11/I2C_MDA
TSUM56AL-1
C152
0.1/50V
C141
AVDD
VCC
HOLD#
WP#
GND
37
38
39
40
4K7
1
2
3
4
8
7
6
5
92
91
90
89
88
87
U106
2
1
6
5
AVDD
82
66
51
34
GPIO_P07
GPIO_P06
GPIO_P02/SAR3
GPIO_P01/SAR2
GPIO_P00/SAR1
RSTN
VCC3.3
8
7
3
4
VCC3.3
C133
RX2P
RX2N
RX1P
RX1N
RX0P
RX0N
RXCKP
RXCKN
GPIO_P14
GPIO_P16/PWM2
DDCD_SDA
DDCD_SCL
VDDC
VDDC
VDDC
VDDC
32
49
56
75
VDDP
VDDP
VDDP
VDDP
24
98
16
AVDD_ADC
3
4
6
7
9
10
12
13
95
99
100
1
AVDD_PLL
R+
RG+
GB+
BCLK+
CLK2 WP
2 DET_DVI
SDA_DVI_I
SCL_DVI_I
BIN0N
BIN0P
GIN0N
GIN0P
SOGIN0
RIN0N
RIN0P
HSYNC0
VSYNC0
DDCA_SDA/RS232_TX
DDCA_SCL/rs232_RX
GPIO_P15/PWM0
VDDC
VCC3.3
22u/25V
2
2
17
18
19
20
21
22
23
27
28
30
31
35
VDDP
4K7x4
RP103
C145
2
2
2
2
2
2
2
2
GNDB
BIN
GNDG
GIN
SOG
GNDR
RIN
HSYNC
VSYNC
DDCA_SDA_I
DDCA_SCL_I
2 DET_VGA
AVDD_MPLL
2
2
2
2
2
2
2
2
2
2
2
AVDD_DVI
AVDD_DVI
8
14
VDVI VMPLLVPLL AVDD
4K7x4
RP102
1
2
3
4
1
2
3
4
RP101
4K7x4
C158 1000P/50V
C159 1000P/50V
C160 1000P/50V
U108
I2C_MCL
I2C_MDA
R178 100
R179
8
7
6
5
100
VCC
WP
SCL
SDA
A0
A1
A2
GND
0.1/50V
C156
1
C157 1000P/50V
VCC3.3
1
2
3
4
U109
HDCP_WP
AT24C04N
8
7
6
5
VCC
WP
SCL
SDA
A0
A1
A2
GND
AT24C04N/NC
1
2
3
4
Model
Title
Date
55
VG1930wm-1
SCALER
Rev:
CN901
8
7
6
5
4
3
2
1
CN903
1
2
3
4
R901
1
2
3
4
Power
2K2
R902
2K2
MUTE
SW TACT
1
2
4
3
SW TACT
1
2
4
3
SW TACT
SW905
1
2
4
3
SW TACT
SW906
1
2
4
3
ZD902
5V6/NC
4
3
SW904
1
2
SW903
5V6/NC
1 4
2 3
SW TACT
SW902
SW901
1
LED901
3
LED Y/B
CN902
from keypad to power key
from keypad
IF Harness
BD
ZD901
From
LED_B
LED_O
SW TACT
POWER
Model
56
VG1930wm-1
Title
Keypad & Power key
Date
Rev:
R703
10K
C706 0.47uF
INL
15
16
Vs
Vs
470uF/16V LEFT_SPEAKER+
12
Mute
TDA_7496L
OutR
14
Svr
10
5K6
C707
1K
1K
R710
C701
C709
R709
220uF/16V
0.1/50V
Gnd
20
Gnd
19
Gnd
18
Gnd
13
Gnd
3
Gnd
2
4700pF
C712
Gnd
Volume
4700pF
2K
R712
R701
C711
2K
+
5K6
+14V
470uF/16V RIGHT_SPEAKER+
C701 change to 220uF from 470uF

for svr rise up earlier
3
R713
R711
R707
10uF/25V
Q701
PMBT3904
C713
27K
Stby
6
5K1
Q703
PMBT3904
1
11
CN701
4
3
2
1
10K
MUTE
C705
17
R706
47K
27K
OutL
U701
R704
R708
INR
+14V
+14V
R705
5,6
VarOut_R
C704 0.47uF
C703
Line_R
10K
VarOut_L
8
R702
Line_L
2
3
4
5
1
N.C.
P701
+14V
C702
0.1/50V
Layout guide :
1. Tie the I.C. pin 1,2,3,18,19,20 to ground with a
large copper pour (open mask layer)
470uF/25V
+14V
VOL
R714
100
1
Q702
PMBT3904
Model
Title
Date
57
VG1930wm-1
Audio
Rev:
3 +14V
R502
680
C502
2.2u/25V
C501
470u/25V
R503
1K5
R504
33
U501
Q501
PMBT3904
ZD501
5V6
0.1/50V
C503
R517 10/NC
5V
R505
33
C504
1000p/50V
op1
C505
T501
1000p/50V SPW-068
6
C508
R506
3M 3KV
C506
10p/3KV
3
220pF/50V/NC
1
ISSEN SSTCMP
12
VSEN
LCT
11
C510
1000p/50V
OVPT
ENA
10
C515
2.2u/25V
R515
NC
NC
DIM
NC
IC501
OZ9938G
U502
1
68p/50V
CT
13
TIMER
C520
3 ON/OFF
R501
100K 1%
R518
470K 1%
C526
0.1/50V
R526
D505
1M
SN4148
4
C523
10p/3KV
8
220pF/50VNC
3
1
2
1
BAV99
C514
2700p/50V
R521
470
3
D504
BAV99
C519
0.1/50V
CN502
2P
op2
R523
C530
470
op3
R525
3M 3KV
D508 BAV99
2
3
1
R531
3K3 1%
D511 SN4148
op1
D512 SN4148
op2
D513 SN4148
op3
C528
3p/3KV
C525
2200p/50V
D509 BAV99
2
1
C527
2700p/50V
R527
CN503
2P
470
R529
470
3
D507
BAV99
C524
0.068/50V
C518
0.1/50V
2
1
T502
SPW-068
R520
100K 1%
D501
SN4148
C522
1000p/50V
6
AP9971GM
5V
D503
R530
33
C529
1000p/50V
C521
GNDA
14
330p/50V
15
0.1/50V
R532
33
C512
DRV2
0.022/25V
VDDA
C511
4
R513
10K 1%
C509
3p/3KV
AP9971GM
R535 0
604K 1%
16
R516
PGND
R512
110K 1%
R514
47K 1%
DRV1
1000p/50V
3 BRIGHTNESS
CN501
2P
470
C513
2200p/50V
C516
R509
NC
R511
200K 1%/ NC
3K3 1%
R534 0
C507
2.2u/25V
D502
BAV99
R510
3 VCC5V
R508
R507
3M3 1% 51K 1%
R524
3
CN504
2P
R528
390 1%
R533
15K 1%
R519
1M
Model
Title
Date
58
VG1930wm-1
Interter
Rev:
8
3
+ C815
1000u/25V
47p/1KV
C808
R817
200R
VCC5V
ZD801
5V6 NC
7
6
Q801
2PC1815GR
ZD802
16V NC
C807
47u/25V
ZD803
9V1
5uH
L803
1000u/10V
D805
C818
SRF5-04CT
D804
+ A02-LF
R816
100R 1W
470u/25V
C817
0.1/50V
C822
DC
700V
Max.
12p/1KV
C826
AP2761I
Q804
1
+14V
9
DC 700V Max.
10R
R806
D803
UFF80-015CT
10R
1000p/500V
R828
C814
MUR1100ERL
D802
R809
510K
5uH
L802
C820
47u/25V
R803
18K
AC 264V
10
AC 264V
L801
20mH
C806
4700p/400V
RMS
RMS
R808
510K
100u/450V
C804
+ 1
D801
BL4-06
R804
68K 2W
11
T801
SPW-055
1000p/500V
C813
R829
10K
C805
2200p/400V
DC 380V Max.
10R
R827
R810
510K
R802
1M
PMBT3906
C823
2200p/400V
R822
5K1 1%
R819
1K
R830
10K
1K
R821
GND
CS
FB
BO
NCP1337
C810
0.1/50V
2
IC801
LTV817M
R815
12K 1%
R814
1K
R818
200
PMBT3904 NC
Q802
1
R820
1K
D806
1N4148
C
A
C824
0.1/50V NC
C821
0.1/100V
DRV
Vcc
NC
HV
4
3
2
1
C812
220p/50V
100p/1KV
C809
5
6
7
8
R823
51K 1%
14V
ZD804
R805
0R24 2W
IC802
RMS
F801
2A/250V
R807
2.4K
R811
510K
AC 264V
C801
C802
2200p/250V 2200p/250V
R825
1K NC
IC803
TLV431ALP
R826
200R NC
R824
3K3 1%
C827
47u/25V
CN801
1
2
3
4
5
6
7
8
P801
L
Q803
3
NTC 5R
RT801
RMS
AC 264V
2
1K
R813
C803
0.47/275V
R812
10K
0.1/50V
C811
R801
1M
AC_SKT
60mm 8P
TO SCALER BD CN101
VCC5V
ON/OFF
2
BRIGHTNESS
2
Volume
4
Audio_MUTE 4
C825
0.1/50V
Model
Title
Date
59
VG1930wm-1
Power
Rev:
11. PCB Layout Diagrams
60
VG1930wm-1
61
VG1930wm-1
62
VG1930wm-1
63
VG1930wm-1
* Readers Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
Unit
Excellent
Good
Fair
Bad
1. Precautions and Safety Notices

2. Specification
3. Front Panel Function Control Description
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram and Exploded Parts List
9. Block Diagrams
11.PCB Layout Diagrams
B. Are you satisfied with this Service Manual?

Item
Excellent
Good
Fair
Bad
1. Service Manual Content

2. Service Manual Layout
3. The form and listing
C. Do you have any other opinions or suggestions regarding this service manual?
Readers basic dada:
Name:
Title:
Company:
Add:
Tel:
Fax:
E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile
1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes
(marc.maupin@viewsonic.com)
64
VG1930wm-1

Viewsonic Vg1930wm-1 SM

Uploaded by

Copyright:

Available Formats

Viewsonic Vg1930wm-1 SM

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Viewsonic Vg1930wm-1 SM

Uploaded by

Copyright:

Available Formats

Service Manual

(VG1930wm-1_SM Rev. 1a Oct. 2006)

Confidential - Do Not Copy

Precautions and Safety Notices

Front Panel Function Control Description

Troubleshooting Flow Chart

Recommended Spare Parts List

Exploded Diagram and Exploded Parts List

10. Schematic Diagrams

11. PCB Layout Diagrams

Confidential - Do Not Copy

1. Precautions and Safety Notices

2. PRODUCT SAFETY NOTICE

Confidential - Do Not Copy

4. Handling and Placing Methods

Confidential - Do Not Copy

Confidential - Do Not Copy

Contrast Ratio (Typ)

Colors (6 bits + 2 bits FRC)

Response Time (Typ)

Viewing Angle (H/V)

160 / 160 @>=10

Analog (75ohms, 0.7/1.0 Vp-p)

Off Mode (Max)

460 x 434 x 230 mm

560 x 525 x 282 mm

Physical (Net Weight)

Package (Gross Weight)

TUV ERGO(covers ISO13406-2 & MPRII), TUV-S, NOM, GOST-R, HYGIENIC

Confidential - Do Not Copy

Test Image Size

Contrast and Brightness Controls

DB-15 (Analog), refer the appendix A

Video Cable Connector DB-15 Pin out

Compliant DDC 1/2B

Video RGB (Analog) Separate,

Maximum PC Video Signal

950 mV with no damage to monitor

Maximum Mac Video Signal

1250 mV with no damage to monitor

Compliant with Revision 1.3

Shall be compatible with all PC type computers,

600, 832 x 624, 1024 x 768, 1152 x 864, 1280 x 960,

Not compatible with interlaced video

Input Voltage Range

Input Frequency Range

Short Circuit Protection

OUTPUT CAN BE SHORTED WITHOUT DAMAGE

Over Current Protection

4 A TYPICAL AT 14.2 VDC

3.5MA (MAX) AT 254VAC / 60HZ

80% TYPICAL AT 115VAC FULL LOAD

INTERNAL AND NOT USER REPLACEABLE

Max Input AC Current

0.8 ARMS @ 90VAC, 0.4 ARMS @265VAC

Inrush Current (Cold Start)

40 A @ 120VAC, 60 A (MAX) @ 220VAC

Power Supply Cold Start

Confidential - Do Not Copy